The aim of this study was to compare the screw removal torque of mini conical prosthetic components and straight trunnion of indexed morse taper implants, after mechanical cycling. The sample consisted of 40 implants and 20 mini-conical prosthetic components (MC group) and 20 straight trunnion components (ST group). Each group consisted of 10 specimens, with 2 implants in each, and cobalt-chromium metallic crowns were screwed into each sample. The components of the MC group received a torque of 20 N.cm with a digital torque wrench and after 10 minutes were retightened with the same value as the initial torque. The components of the ST group received a torque of 30 N.cm, with a digital torque wrench and after 10 minutes, they were retightened with the same value. The screws of the respective crowns of the two groups received a torque of 10 N.cm and after 10 minutes were retightened with the same value. Each group was subjected to the fatigue test in a mechanical cycler at 2.000.000 cycles, with a load of 250 N and frequency of 4 Hz. At the end of the fatigue test, the loosening torque of each screw of the specimens was measured through a digital torque wrench. The data were analyzed by two-way ANOVA and Tukey test. In both groups, there were loss of torque. The results showed no statistic difference between MC and ST groups.

This study aimed to evaluate the impact of Candida albicans on subgingival biofilm formation on dental implant surfaces. Scanning electron microscopy (SEM) and confocal laser scanning microscopy (CLSM) were used to compare biofilm structure and microbial biomass in the presence and absence of the fungus after periods of 24, 48, and 72 h. Quantitative polymerase chain reaction (qPCR) was used to quantify the number of viable and total micro-organisms for each of the biofilm-forming strains. A general linear model was applied to compare CLSM and qPCR results between control and test conditions. The biofilm developed with C. albicans at 72 h had a higher bacterial biomass, with a significantly higher cell viability (p < 0.05). After both 48 and 72 h of incubation, in the presence of C. albicans, there was a significant increase in counts of Fusobacterium nucleatum and Porphyromonas gingivalis and in the cell viability of Streptococcus oralis, Aggregatibacter actinomycetemcomitans, F. nucleatum, and P. gingivalis. Using a dynamic in vitro multispecies biofilm model, C. albicans exacerbated the development of the biofilm grown on dental implant surfaces, significantly increasing the number and cell viability of periodontal bacteria.

Peri-implant bone resorption has been reported around some implants after loading and this could create problems for the long-term stability of peri-implant soft and hard tissues. The causes are still not completely known, but a relevant importance could be assumed by the presence of a bacterial contamination at the micro-gap level of the implant-abutment junction. In this regard, external and internal implant-abutment assemblies have been shown to be much more permeable to bacterial colonization than Cone-Morse or conical connections. A subcrestal implant placement could have aesthetic advantages allowing a better prosthetic emergence profile. In literature controversial experimental and clinical results have been reported about bone resorption around implants placed equicrestally and subcrestally. Interestingly, Finite Element Analysis (FEA) studies revealed to be extremely useful for assessing the peri-implant bone strain and stress. Thus, the aim of this study was a FEA evaluation of implants with a Cone-Morse implant-abutment assembly (Implacil De Bortoli, São Paulo, Brazil) inserted into a bone block model (width: 10 mm, vertical height: 17.5 mm, thickness of the cortical area: 1.5 mm) mimicking equicrestal and subcrestal placements (1 and 2 mm). The results demonstrated that maximum stresses were observed within the cortical bone around the equicrestally placed implants, the lowest in the implant placed 2-mm subcrestally and intermediate stresses within the implant placed 1-mm subcrestally. Cortical bone was more stressed under lateral loads than axial loads. In conclusion, this FEA study suggested that implant placement at -1 mm could be recommended.

Background: Fiber-reinforced composites (FRCs) have been proposed as an alternative to traditional metal alloys for the realization of frameworks in full-arch implant supported prostheses. The aim of the present in vitro study was to evaluate the deflection under load of seven prostheses endowed with frameworks made of different materials, including different types of fiber reinforced composites (FRCs). Methods: A master cast with four implant analogues in correspondence of the two lateral incisors and the two first molars was used to create full-arch fixed prostheses with the same shape and different materials. Prostheses were made in different materials (framework+veneering material): gold alloy+resin (Au+R), titanium+resin (Ti+R), FRC with multi-directional carbon fibers+resin (ICFRC+R), FRC with unidirectional carbon fibers+composite (UCFRC+C), FRC with glass fibers+resin (GFRC+R), FRC with glass fibers+composite (GFRC+C), resin (R, full-acrylic prosthesis). Flexural tests were conducted using Zwick/Roell Z 0.5 machine and the deflection of the lower surface of the prosthesis was measured in order to obtain load/deflection graphs. Results: Greater rigidity and less deflection were recorded for UCFRC+C, GFRC+C, followed by Ti+R, and Au+R. The greatest deformations were observed for resin alone, ICFRC+R and GFRC+R. The results were slightly different in the incisal region probably due to the greater amount of veneering material in this area. Conclusions: When used to realize full-arch frameworks, Au and Ti allow a predictable mechanical behavior with gradual deformations with increasing load. UCFRC also demonstrated good outcomes and less deflection than ICFRCs when loaded. The GFRC full-arch framework may be a valid alternative, however showed greater deflections. Further studies are needed in order to evaluated how different prosthesis design and material thickness might affect the outcomes.

Background: Patients with thromboembolic disease, prosthetic valves, or coagulation issues are commonly prescribed anticoagulants and antiplatelets. Although common professional oral hygiene might not represent a health concern for these patients, anticoagulant and antiplatelet medication might constitute a challenge for dentists and dental hygienists since possible prolonged bleeding might interfere with dental procedures. The aim of the present study was to investigate the bleeding time of different anticoagulants and antiplatelets during a professional hygiene session adapting the Ivy test to the oral environment; Methods: 93 consecutive patients undergoing professional oral hygiene were recruited. Debridement during oral hygiene was performed using ultrasonic mechanical instrumentation, and bleeding sites were assessed and treated with gentle pressure using sterile gauzes. The time for bleeding cessation was recorded. Patients were categorized into six groups based on their drug intake, Control: no anticoagulants or antiplatelets DTI: direct thrombin inhibitors (dabigatran) AntiXa: directa factor Xa inhibitors (endoxaban, apixaban, rivaroxaban) VKA: vitamin K antagonists (warfarin, acenocoumarol) SAPT: single anti-platelet therapy (acetylsalicylic acid or clopidogrel) DAPT: dual anti-platelet therapy (acetylsalicylic acid and clopidogrel). Bleeding time was measured in seconds and mean values were assessed among the different groups. Differences between groups were investigated with Kruskal-Wallis test followed by Dunn’s post-hoc correction for multiple comparisons or two-way ANOVA followed by Dunnett post-hoc; Results: Control patients presented the lowest bleeding time 50 sec, followed by AntiXa (98), SAPT (105), DTI (120), DAPT (190) and VKA (203). A statistically significant difference was present among control and DTI (p=0.004), VKA (p<0.001), DAPT (p<0.001). Conclusions: Based on the present outcomes, an increased risk of prolonged bleeding emerged in patients taking VKA and DAPT. However, bleeding did not interfere with the oral hygiene ses-sion The optimal period for dental treatment of these patients should be 2-3 hours before the next dose, without the need to temporarily suspend the medication.

Aseptic implant loosening after total joint replacement is partially influenced by material-specific factors when cobalt-chromium alloys are used, including osteolysis induced by wear- and corrosion products, and stress shielding. Here, we aim to characterize a hybrid material consisting of alumina-toughened zirconia ceramics (ATZ) and additively manufactured Ti-35Nb-6Ta (TiNbTa), joined by a glass solder. The structure of the joint, static and fatigue shear strength, the influence of accelerated aging, and the cytotoxicity using an elution assay with human osteoblasts is characterized. Furthermore, the biomechanical properties of functional demonstrators of a femoral component for total knee replacements are evaluated. TiNbTa-ATZ specimens showed a homogenous joint with statistical distributed micro-pores and a slight accumulation of Al-rich compounds at the glass solder-TiNbTa interface. The static shear strength was 26.4 ± 4.2 MPa (Ti-ATZ reference: 38.2 ± 14.4 MPa, p = 0.117), all specimens survived 107 cycles of shear loading to 10 MPa, and aging did not reduce the strength. TiNbTa-ATZ did not impair the proliferation and metabolic activity of human osteoblasts. Functional demonstrators of TiNbTa-ATZ provided a maximum bearable extension-flexion moment of 40.7 ± 2.2 Nm. Biomechanical and biological properties of TiNbTa-ATZ demonstrate potential application for endoprosthetic implants.

The human mandible's cancellous bone, which is characterized by its unique porosity and directional sensitivity to external forces, is crucial for sustaining biting stress. Traditional CAD models fail to fully represent bone's anisotropic structure and thus depend on simple isotropic assumptions. For our research, we use the latest versions of nTopology and Creo Parametric software to make biomimetic Voronoi lattice models that accurately reflect the complex geometry and mechanical properties of trabecular bone. The porosity of human cancellous bone is accurately modeled in this work using biomimetic Voronoi lattice models. The porosities range from 70% to 95%, which can be achieved by changing the pore sizes to 1.0 mm, 1.5 mm, 2.0 mm, and 2.5 mm. Finite element analysis (FEA) was used to examine the displacements, stresses, and strains acting on dental implants with a buttress thread, abutment, retaining screw, and biting load surface. The results show that the Voronoi model accurately depicts the complex anatomy of the trabecular bone in the human jaw, compared to standard solid block models. The ideal pore size for biomimetic Voronoi lattice trabecular bone models is 2 mm, taking into account both the von Mises stress distribution over the dental implant, screw retention, cortical bone, cancellous bone, and micromotions. This pore size displayed balanced performance by successfully matching natural bone's mechanical characteristics. Advanced finite element analysis (FEA) improves biomechanical understanding of how bones and implants interact by creating more accurate models of biological problems and dynamic loading situations. This makes biomechanical engineering better.

This study examines the effect of a hyaluronic acid (HyAc) containing tricalcium phosphate putty scaffold material (TCP-P) and of a particulate tricalcium phosphate (TCP-G) graft on bone formation, volume stability and osteogenic marker expression in biopsies sampled 6 months after bilateral sinus floor augmentation (SFA) in 7 patients applying a split-mouth design. Biopsies were processed for immunohistochemical analysis of resin embedded sections. Sections were stained for collagen type I (Col I), alkaline phosphatase (ALP), osteocalcin (OC) and bone sialoprotein (BSP). Furthermore, the bone area and particle area fraction were determined histomorphometrically. Cone-beam CT data recorded after SFA and 6 month later were used for calculating the graft volume at these two time points. TCP-P displayed more advantageous surgical handling properties and a significantly greater bone area fraction and smaller particle area fraction. This was accompanied by significantly greater expression of Col I and BSP and in osteoblasts and osteoid and a less pronounced reduction in grafting volume with TCP-P. SFA using both types of materials resulted in formation of sufficient bone volume for facilitating stable dental implant placement with all dental implants having been in function without any complications for 6 years. Since TCP-P displayed superior surgical handling properties and greater bone formation than TCP-G, without the Hyac hydrogel matrix having any adverse effect on bone formation or graft volume stability, TCP-P can be regarded as excellent grafting material for SFA in a clinical setting.

Introduction: congenital ureteral stenosis is one of the leading causes of impaired urinary drainage and subsequent dilatation of urinary collecting system, known as hydronephrosis or ureterohy-dronephrosis. Mechanism that leads to obstruction is not clearly known. Multiple studies in rat models have shown increased angiotensin 11 and TGFβ levels in obstructed ureteral tissue. The aim of the study is to investigate expression of fibrosis related genes in obstructive and normal ureteral tissue. Material and methods: it is a monocentric study in which nineteen patients were selected prospec-tively. 17 patients of which underwent Hynes-Anderson pyeloplasty due to the PUJO, 2 patients underwent ureteroneocystostomy due to ureterovesical junction obstruction (UVJO) and 6 patients were chosen for control group: 5 underwent nephrectomies due to the kidney tumor and 1- upper pole heminephrectomy due to the duplex kidney with normal pyeloureteric junctions in all. Tissue RNA was chemically extracted after freezing the biopsy samples in liquid nitrogen, with cDNA synthesis performed immediately after nucleic acid isolation. qPCR to evaluate the relative expres-sion of Tgfb1, Mmp1, Timp1, Pai1, Ctgf and Vegfa was performed. Expression levels of Gapdh and Gpi genes (geometric average) were used to calculate the relative expression of the investigated genes. Outliers were removed prior to calculating confidence intervals for the experimental groups, and Wilcoxon rank-sum test was performed to determine statistical significance of the differences. Results: significant differences between healthy and stenotic tissue samples in Ctgf gene expression levels were observed, with the samples from afflicted tissue showing lower expression. No statistical difference in expression levels of Tgfb1, Timp1, Vegfa, Mmp1, Pai1 was found. Discussion and conclusions: These findings suggest that tissue fibrosis similar to other tissues and organs is not the leading cause of stenosis, at least at the moment of surgery. Decreased CTGF ex-pression is indicative of developmental origin of obstruction.

The aim of this study was to evaluate the use of a flexible synthetic polymer bone graft to provide implant stability in the absence of implant stability during implant placement in a dense cortical bone model. Sockets were prepared on polyurethane blocks according to the standard implant socket drilling protocol in the control group, both oversizing and deepening in group 2, and oversizing only in group 3. In groups 2 and 3, flexible synthetic polymer bone grafts were placed in the sockets prior to implant placement. The implants were placed at bone level in all groups. The highest torque value obtained was recorded as the insertion torque. 75 implant sites in 3 groups were included in the study. The torque values of the implants in the control group were significantly higher than those of the implants with the oversized and deepened sockets and the oversized-only sockets (p<0.05; p<0.01).The torque values of the implants with the oversized and deepened sockets were significantly higher than those of the implants with the oversized-only sockets (p<0.01). In this study, flexible synthetic polymer bone graft was shown to be effective in achieving implant stability in the management of implants with loss of primary stability.

The aim of this study was to evaluate the effect of two different insertion speeds at 8 different insertion torque values ranging from 25-60 during implantation in a dense polyurethane D1 bone model on the placement status and removal torque of dental implants. In this study, 50 pcf single layer polyurethane plates were used. In the study, a total of 320 implant sockets were divided into 2 groups as Group 1 (30 rpm) and Group 2 (50 rpm) in terms of insertion speed. Group 1 and Group 2 were divided into 8 subgroups as 25, 30, 35, 40, 45, 50, 55 and 60 torques. There were 20 implant sockets in each subgroup. During the implantations, implant placement status and removal torque values were assessed. There was a statistically significant difference between the 30 and 50 RPM groups in terms of overall implant placement status (p<0.01). It was found that the removal torque values at 50 RPM were statistically significantly higher than those at 30 RPM (p<0.01). This study showed that in dense D1 bone, the minimum parameters at which all implants could be placed at bone level were 50 torque at 30 rpm and 40 torque at 50 rpm.

Gastroesophageal (GE) junction adenocarcinoma is an aggressive malignancy of growing incidence and is associated with public health issues such as obesity and GERD. Management has evolved over the last 2 decades to incorporate a multidisciplinary approach including endoscopic intervention, and neoadjuvant chemotherapy/ chemoradiation and minimally invasive or more limited surgical approaches. Surgical approaches include esophagectomy, total gastrectomy, and more recently proximal gastrectomy. This review analyzes the evidence for and applicability of these varied approaches in management as well areas of continued controversy and investigation.

Cell junction that is usually associated with dynamic cytoskeletons is essential for a wide range of cellular activities such as cell migration, cell communication, barrier function and signal transduction. Real-time observation of cell junction facilitates understanding of the mechanisms by which cell junction regulate relevant cellular activities. In this study, we examined the binding capacity of a modified tridecapeptide from Cx43 to cell junction protein ZO-1 and sought to create a fluorescent peptide that could be used to label cell junction. To introduce the fluorescent peptide into the cells, a cell-penetrating peptide was linked to the modified tridecapeptide and synthesized. The binding of the modified tridecapeptide was tested using pull down and immunoprecipitation assay. The ability of the peptide to label cell junction was assessed by adding it to fixed or cultured Caco-2 cells. Testing assay revealed that the Cx43-derived peptide can bind to ZO-1. Besides, the peptide was able to label cell junction of fixed cell, although no obvious cell junction labeling was observed clearly in living cells, probably due to the inadequate affinity. These results indicate that a peptide-based strategy for labeling cell junction may be feasible, and efforts to improve its affinity are warranted in the future.

Transcatheter aortic valve implantation (TAVI) has grown exponentially within the cardiology and cardiac surgical spheres. It has now become a routine approach for treating aortic stenosis. Several uncertainties have been raised about TAVI in comparison to conventional surgical aortic valve replacement (SAVR). The primary concerns are with regards to the longevity of the valves. Several factors have been identified that may predict poor outcomes following TAVI. These include the lesser-used finite element analysis (FEA) to quantify the properties of calcifications that affect TAVI valves. This can also be used in conjunction with other integrated software to ascertain the functionality of these valves. Other imaging modalities are now widely available such as Multi-detector row computed tomography(MDCT) which can accurately size the aortic valve annulus.. This may help reduce the incidence of paravalvular leaks and regurgitation which may necessitate further intervention. Structural valve degeneration (SVD) remains a key factor with varying results from current studies. The true incidence of SVD in TAVI compared to SAVR remains unclear with the lack of long term data. It is now widely accepted that both are part of the armamentarium and are not mutually exclusive. Decision-making for the appropriate intervention should be made via shared decision-making involving the heart team.

As medical care aiming to maintain the quality of life for elderly patients is increases, implant treatment for elderly patients is increasing worldwide. Therefore, we aimed to investigate implant stability and the reliability of different measuring devices according to implant placement site and duration in patients aged over 65 years. The study evaluated 60 implants in 60 patients aged ≥ 65 years. The implant placement sites were divided into six evenly distributed sections (n=10) i.e., maxillary right- posterior, A; maxillary anterior, B; maxillary left-posterior, C; mandibular right-posterior, D; mandibular anterior, E; mandibular left-posterior, F. Participants visited the hospital seven times: preoperatively, 1V; implant surgery, 2V; stitch removal, 3V; 1-month follow-up, 4V; 2-months follow-up, 5V; before final-restoration delivery, 6V; and after final-restoration delivery, 7V. The implant stability was evaluated with the Osstell Mentor (ISQ), Periotest M (PTV), and Anycheck (IST). The mean values of ISQ, PTV, and IST were analyzed (α=.05). ISQ, PTV, and IST results of 5V and 6V were significantly higher than those of 2V (P<.05). The lowest ISQ results occurred in E location at 5V and 6V (P<.05). In all mandibular locations, IST results of 7V were significantly higher than those of 2V, 3V, 4V, and 5V (P<.05). ISQ results were negatively correlated with PTV and positively correlated with IST, and PTV was negatively correlated with IST. By considering various factors that affect implant stability, the appropriate implant load application time was determined. This could help increase the implant success rate in elderly patients. And as a diagnostic device for implant stability for evaluation of osseointegration in elderly patients, Anycheck was also able to prove its relative reliability compared to Osstell ISQ Mentor and Periotest M.

Multi-junction solar cells comprised of stacked III-V semiconductor junctions represent the highest-efficiency photovoltaic technology, with recent demonstrations exceeding 47% efficiency . Optimizing the design and thickness of each junction is critical for maximizing performance . This work utilizes Silvaco TCAD tools to systematically optimize a 5-junction cell based on AlInP, AlGaInP, AlGaInAs, GaInP, GaAs, InGaAs, and Ge similar to recent record cells . The junction thicknesses are varied using a predictive profiler to sample the parameter space . For each combination, the spectral absorption and I-V characteristics are simulated to determine the efficiency . Statistical analysis identifies the optimal thickness set that maximizes performance to 26% under 1 sun illumination .

Although the connection of implant abutments to implant analogs and implant bodies has been evaluated separately, comparative evaluation of connections to implant analogs and implant bodies has not been evaluated. The objective of this study was to identify whether torque applied during laboratory manufacturing and during restoration cementation affects the compatibility between the implant body-abutment and the implant analog-abutment, as well as to spot any structural differences. Three different implant system with internal conical connection (Bioinfinity, Dant, and Dentist) were used. For each group, straight abutments (n=20) were tightened to implant analogs (n=10) and implant bodies (n=10) with hand tightening and using torque wrench device. The fitting of componenets were evaluated for each group using linear and volumetric micro-CT analysis. For linear analysis, when the mean differences (difference between measurements of the linear distance of abutments during hand tightening and applying torque) values between implant analog and implant body were compared within groups, There was no statistically significant difference observed in all groups (p&gt; 0.05). Throughout the fabrication and clinical phases, it is recommended to tighten the abutments on the analogs with a torque wrench instrument to minimize the risk of prosthetic incompatibility.

Motivated by the increasing need of optimised micro-devices for droplets production in medical and biological applications, this paper introduces an integrated approach for the study of the liquid-liquid droplet creation in flow-focusing micro cross-junctions. The micro-junction considered is characterised by a restriction of the channels cross-sections in the junction, which has the function of focusing the flow in the region of the droplet formation. The problem is studied numerically in OpenFOAM environment and validated by the comparison with experimental results obtained by high-speed camera images and micro-PIV measurements. The analysis of the forces acting on the dispersed phase during the droplet formation and the diameter of the droplets obtained numerically are considered for the development of a model of the droplet breakup under the squeezing regime. On the basis of energy balancing during the breakup, a relation between interfacial tension, the size of the cross-sections in the junction, and the time interval needed for droplet creation is obtained, which yields a novel correlation between the dimensionless length of the droplet and the dimensionless flow rate. This correlation is general and can be used to predict the droplet diameters produced by similar micro-junctions with different aspect ratios and extended to different geometries of flow-focusing micro-junctions.

The gap junction-coupled astroglial network plays a central role in the regulation of neuronal activity and synchronization, but its involvement in the pathogenesis of neuronal diseases is not yet understood. Here we present the current state of knowledge about the impact of impaired glial coupling in the development and progression of epilepsy and discuss whether astrocytes represent alternative therapeutic targets. We focus mainly on temporal lobe epilepsy (TLE), which is the most common form of epilepsy in adults, characterized by high therapy resistance. Functional data from TLE patients and corresponding experimental models point to a complete loss of astrocytic coupling, but preservation of the gap junction forming proteins connexin43 (Cx43) and connexin30 (Cx30) in hippocampal sclerosis. Several studies further indicate that astrocyte uncoupling represents a causal event in the initiation of TLE, as it occurs very early in epileptogenesis, clearly preceding dysfunctional changes in neurons. However, more research is needed to fully understand the role of gap junction channels in epilepsy and to develop safe and effective therapeutic strategies targeting astrocytes.

Angiogenesis, the sprout and growth of new blood vessels from existing vasculature, is an important process of tumor development for the supply of oxygen and nutrition to cancer cells. Endothelial cell is a critical player in angiogenic process by modulating cell proliferation, cell motility, and cell morphology in the response to pro-angiogenic factors and environments provided by tumor and cancer cells. Recent in vivo and in vitro studies have revealed that gap junction of endothelial cells also participates in the promotion of angiogenesis. Pro-angiogenic factors modulate gap junction function and connexins expression in endothelial cells, whereas endothelial connexins involve in angiogenic tube formation and cell migration of endothelial cells via both gap junction channel function dependent or independent mechanisms. In particular, connexin might have the potential to regulate cell mechanics such as cell morphology, cell migration, and cellular stiffness that are dynamically changed during angiogenic processes. Here, we review the implication for endothelial gap junction and cellular mechanics in vascular angiogenesis.

This article addresses the trajectory tracking between two non-identical systems with chaotic properties. We employ the Rossler chaotic and RCL-shunted Josephson junctions model in similar phase space to study trajectory tracking. In order to achieve the goal tracking, we afford two stages to approximate the target tracking. The first stage utilizes the active control technique to transfer the output signal from the RCLs-J system into the quasi-Rossler system. Then next, the RCLs-J system employs the proposed the iterative learning control scheme and the control signal from the drive system to trace the trajectory of Rossler system. The numerical results demonstrate the proposed method and the tracking system is asymptotically stable.

Background: Cochlear implantation is an efficient treatment for postlingually deafened adults who do not benefit sufficiently from acoustic amplification. Implantation is indicated when it can be foreseen that speech recognition with a cochlear implant (CI) is superior to that with a hearing aid. Especially for subjects with residual speech recognition it is desirable to predict CI outcome on the basis of preoperative audiological tests. Purpose: The purpose of the study was to extend and to refine a previously developed model for CI outcome prediction for subjects with preoperative word recognition to include subjects with no residual hearing by incorporat-ing additional results of routine examinations. Results: By introducing the duration of unaided hearing loss (DuHL) the median absolute error (MAE) of the prediction was reduced. While for subjects with preoperative speech recognition the model modification did not change the MAE, for subjects with no residual speech recognition before surgery, the MAE decreased from 23.7% with the previous model to 17.2% with the extended model. Conclusions: Prediction of word recognition with CI is possible within clinically relevant limits. Outcome prediction is particu-larly important for preoperative counselling and in CI aftercare, to support systematic monitor-ing of CI fitting.

We review the topological gauge theory description of Josephson junction arrays (JJA), fabricated systems which exhibit the superconductor to insulator transition (SIT). This description revealed the topological nature of the phases appearing at the SIT and lead to the discovery of a new state of matter, the superinsulator, characterized by an infinite resistance, even at finite temperature, due to linear confinement of electric charges. This discovery is particularly relevant for the physics of superconducting films with emergent granularity, which are modeled by JJA, and share the same phase diagram.

The tricellular tight junction protein angulin-1/lipolysis-stimulated lipoprotein receptor (LSR) is associated with numerous signal transduction pathways that regulate gene expression, epithelial cell function, and morphogenesis. The impacts of particulate matter on LSR and asthma are not known. Therefore, the aim of the present study was to assess the impacts of particulate matter as one of air pollution on LSR expression in asthma. To this end, we investigated the involvement of LSR in the pathogenesis of bronchial asthma in an ovalbumin (OVA) mouse model of asthma exposed to titanium dioxide (TiO2), and examined plasma LSR levels and their relationship with clinical variables in asthma patients and healthy controls. Plasma LSR levels were lower in asthma patients than in healthy controls. Although plasma levels of receptor for advanced glycation end-products (RAGE) were lower in asthma patients than in healthy controls, high mobility group box protein 1 (HMGB1) levels did not differ between these groups. In asthma patients, LSR levels were correlated with the forced vital capacity percentage, ratio of forced expiration (first second)-to-forced vital capacity, white blood cell count, and blood lymphocyte proportion. In mice, LSR expression was significantly decreased in OVA mice compared with control mice, and changed in OVA mice exposed to TiO2. Transforming growth factor beta levels were increased in OVA mice compared with control mice, and changed in OVA mice exposed to TiO2. Overall, plasma LSR levels were decreased in asthma patients, and were influenced by exposure to air pollution. These findings suggest the involvement of LSR in the pathogenesis of asthma.

Background and Objectives: This study aimed to evaluate the histological and biochemical ef-fects of capsaicin on implant osseointegration and oxidative stress. Materials and Methods: Male Wistar albino rats weighing between 250 and 300 grams were used in this study. Twenty-four rats were randomly divided into three equal groups: implant + control (n= 8), implant + capsai-cin-1 (n= 8), and implant + capsaicin-2 (n= 8). 2.5 mm diameter and 4 mm length titanium im-plants were surgically integrated into the corticocancellous bone parts of the femurs. In the treatment groups, rats were injected intraperitoneally with 25 mg/kg (implant + capsaicin-1) and 50 mg/kg (implant + capsaicin-2) of capsaicin. No additional applications were made in the con-trol group. Three rats in totally were died during and after the experiment, as a result of the an-alyzes performed on 21 animals. Results: The highest total antioxidant status value was found in capsaicin dose 2, according to the analysis. The control group had the highest total oxidant status and oxidative stress index values, while group 2 of capsaicin had the lowest. After analysis, we found that there was no observed positive effect on osteointegration in this study (p> 0.05), alt-hough the bone implant connection was higher in the groups treated with capsaicin. Conclusi-ons: A positive effect on osteointegration was not observed in this study. This may be due to os-teaclast activation. However it was found that it has a positive effect on oxidative stress. Osteo-clast activation may be the cause of this phenomenon. Capsaicin was found to have a positive effect on oxidative stress (p

Porous structured metallic implants are preferable as bone graft substitutes due to their faster tissue integration mediated by bone in-growth and vascularization. The porous scaffolds/ implants should also mimic the graded structure of natural bone to ensure a match of mechanical properties. This article presents a method to design graded porous structured acetabular implant and identifies the suitable parameters for manufacturing the model through additive manufacturing. The design method is based on slice-wise modification to ensure continuity of gradation. Modification of the slices was achieved through the binary image processing route. A geodesic dome type design was adopted for developing the acetabular cup model from the graded porous structure. The model had a solid shell with the target porosity and pore size gradually changing from 65% and 950 µm, respectively, in the inner side to 75% and 650 µm, respectively, towards the periphery. The required dimensions of the unit structures, and the combinations of pore structure and strut diameter to obtain the target porosity and pore size were determined analytically. Suitable process parameters were identified to manufacture the model by Direct Metal Laser Sintering (DMLS) using Ti6Al4V powder after carrying out a detailed experimental study to minimize the variation of surface roughness and warping over different build angles of the strut structures. A dual contour scanning was implemented to simplify the scan strategy. The minimum diameter of struts that could be manufactured using the selected scanning strategy and scanning parameters was found to be 375 µm. Finally, the model was built and from the micro-CT data, the porosities and pore sizes were found to be closely conforming to the designed values. The stiffness of the structures, as found from compression testing, was also found to be well matching with that of human trabecular bone. Further, the structure exhibited compliant bending-dominated behavior under compressive loading.

Background: Actually, resonance frequency analysis (RFA) is the most extended method for measuring implant stability. The implant stability quotient (ISQ) is the measure obtained by the different RFA devices, however, inter- and intra- rater reliability and validity of some devices remains unknown. Methods: Thirty implants were placed in 3 different pig mandibles. ISQ was measured axial and parallel with Osstell® Beacon, Penguin® and MegaISQ® by 2 different operators and one operator performed a test-retest. Intraclass correlation coefficient was calculated to assess the intra- and inter-rater reliability. Pearson correlation coefficient was used to assess the validity. Results: The higher inter- and intra- rater reliability was obtained by Penguin® when measuring axial. The highest ISQ values were obtained using Penguin® in an axial measurement; the lowest, using the MegaISQ® in an axial measurement. The highest correlation values with the other devices were obtained by MegaISQ® measuring axially. Conclusion: Penguin® had a good reliability for measuring ISQ both inter- and intra- rater. Osstell® had good validity for measuring ISQ both axial and parallel and MegaISQ® had the best validity for measuring ISQ axial.

The aim of the present study was to monitor implant stability after sinus floor elevation with two biomaterials during the first 6 months of healing by a resonance frequency analysis (RFA), and how physico-chemical properties affect the implant stability quotient (ISQ) at the placement and healing sites. Bilateral maxillary sinus augmentation was performed in 10 patients in a split-mouth design using a bobine HA (BBM) as a control and porcine HA (PBM). Six months after sinus lifting, 60 implants were placed in the posterior maxilla. The ISQ was recorded on the day of surgery from RFA at T1 (baseline), T2 (3 months), and T3 (6 months). Statistically significant differences were found in the ISQ values during the evaluation period. The ISQ (baseline) was 63.8±2.97 for BBM and 62.6±2.11 for PBM. The ISQ (T2) was ~ 73.5±4.21 and 67±4.99, respectively. The ISQ (T3) was ~ 74.65±2.93 and 72.9±2.63, respectively. All the used HAs provide osseointegration and statistical increases in the ISQ at baseline, T2 and T3 (follow-up), respectively. The BBM, sintered at high temperature with high crystallinity and low porosity, presented higher stability, which demonstrates that variations in the physico-chemical properties of a bone substitute material clearly influence implant stability.

It is becoming clear that in addition to gap junctions, playing a role in cell-cell communication, gap junction proteins, connexins, located in cytoplasmic-compartments may have other important functions. Mitochondrial connexin 43 (Cx43) is increased after ischemic preconditioning and has been suggested to play a protective role in the heart. How Cx43 traffics to the mitochondria and the interactions of mitochondria with other Cx43-containing structures are unknown. In this study, immunocytochemical, super-resolution and transmission electron microscopy were used to detect cytoplasmic Cx43-containing structure and to demonstrate their interactions with other cytoplasmic organelles. The most prominent cytoplasmic Cx43-containing structures, annular gap junctions, were demonstrated to form intimate associations with lysosomes as well as with mitochondria. Surprisingly, the frequency of associations between mitochondria and annular gap junctions was greater than that between lysosomes and annular gap junctions. The benefits of annular gap junction/mitochondrial associations are not known. However, it is tempting to suggest that the contact between annular gap junction vesicles and mitochondria facilitates Cx43 deliver to the mitochondria. Furthermore, it points to the need for investigating trafficking of Cx43 to cytoplasmic compartments and annular gap junction as more than only a vesicle destined for degradation.

Gap junctions (GJs) made of connexin-43 (Cx43) are important for the conduction of electrical impulses in the heart. Modulation of Cx43 activity may be useful in the treatment of cardiac arrhythmias and other dysfunctions. Search of novel GJ modulating agents using molecular docking approach allows to predict the binding affinities that often significantly differ from experimentally estimated their potencies. The objective of this study was to demonstrate that Quantitative Structure-Activity Relationship (QSAR) model could be used for more precise identification of potent Cx43 GJ inhibitors. Using the QSAR model and molecular docking, we evaluated the known Cx43 GJ inhibitors, suggested a new one, and tested it experimentally. Our QSAR model predicted the concentrations required to produce 50% of the maximal effect (IC50) for each of these compounds and estimated the correlation between predicted and experimental IC50ies (pIC50 and eIC50). This led to suggestion of monocyclic monoterpene d-limonene as putative Cx43 inhibitor with pIC50 = 1.07. In turn, dual whole-cell patch-clamp measurements provided eIC50=1.41. The pIC50ies of d-limonene and other Cx43 GJ inhibitors examined by our QSAR model well correlated with their eIC50ies (R = 0.88) in contrast to pIC50s obtained from molecular docking (R = 0.42). However, the molecular docking suggested that inhibitor potency may depend on their docking sites on Cx43.

In this review, we provide an overview of the most common majority and minority charge carrier traps in n-type 4H-SiC material. We focus on the results obtained by different applications of junction spectroscopy techniques. The basic principles behind the most common junction spectroscopy techniques are given. These techniques, namely, deep level transient spectroscopy (DLTS), Laplace DLTS (L-DLTS) and minority carrier transient spectroscopy (MCTS) have led to recent progress in identifying and better understanding of the charge carrier traps in n-type 4H-SiC material.

Due to increased energy intensive human activities resulting accelerated demand for electric power coupled with occurrence of natural disasters with increased frequency, intensity, and duration, it becomes essential to explore and advance renewable energy technology for sustainability of the society. Addressing the stated problem and providing a radical solution has been attempted in this study. To harvest the renewable energy, among variety of solar cells reported, a composite a-Si/CZTS photovoltaic devices has not yet been investigated. The calculated parameters for solar cell based on the new array of layers consisting of a-Si/CZTS are reported in this study. The variation of i) solar cell efficiency as a function of CZTS layer thickness, temperature, acceptor, and donor defect concentration; ii) variation of the open circuit current density as a function of temperature, open circuit voltage; iii) variation of open circuit voltage as a function of the thickness of the CZTS layer has been determined. There has been no reported study on a-Si/CZTS configuration-based solar cell, analysis of the parameters, and study to address the challenges imped efficiency of the photovoltaic device and the same has been discussed in this work. The value of the SnO2/a-Si/CZTS solar cells obtained from the simulation is 23.9 %.

Fatigue analysis plays a vital role in determining the structural integrity and life of a dental implant. With the use of such implants on the rise, there is a corresponding increase in the number of implant failures. As such, the aim of this research paper is to investigate the life of 3D-printed dental implants. The dental implants considered in this study were 3D printed according to the direct metal laser sintering (DMLS) method. Additionally, a finite element model was developed to study their performance, while fatigue life was predicted using Fe-Safe software®. The model was validated experimentally by performing fatigue tests. The life of the dental implants was analysed based on Normal strain and the Brown-Miller with Morrow mean correction factor algorithm. The model revealed that there was a strong correlation between the FEA and the experimental results. The clinical success of 3D-printed dental implant experimentally is 20.51 years and computationally under Normal strain is 19.89 years and Brown-Miller with Morrow mean correction factor is 26.82 years.

This study evaluated the mechanical strengths of three types of orthodontic micro-implants by analyzing their structural configurations. Thirty micro-implants of three types (diameter 1.5 mm, Types A, B, C) were assessed. All micro-implants were manually driven into artificial bones at an 8-mm depth. The insertion torque (IT), pullout strength (PS), and gripping volume (GV) of each type were measured. Intergroup comparisons and intragroup correlation were investigated by statistical analysis. Type B had the greatest inner–outer diameter ratio (0.67), and Type A had the smallest (0.53). The IT of Type A (5.26 Ncm) was significantly (p = 0.038) lower than that of Type C (8.8 Ncm). There was no significant difference in the pullout strength (p = 0.868). The GV of Type A (9.7 mm3) was significant (p < 0.01) greater than Type C (8.4 mm3). Type C was significant (p < 0.01) greater than Type B (7.2 mm3). Spearman’s rho rank correlation test showed that PS of Type B was correlated significantly with GV. In conclusion, the design of thread and its GV were the important factors on the mechanical strengths of micro-implant.

This review article deals with the design of bioactive calcium phosphate coatings deposited on metallic substrates to produce bone implants. The bioceramic coating properties are used to create a strong bonding between the bone implants and the surrounding bone tissue. They provide a fast response after implantation and increase the lifespan of the implant in the body environment. The first part of the article describes the different compounds belonging to the calcium phosphate family and their main properties for applications in biomaterials science. The calcium to phosphorus atomic ratio (Ca/P)at. and the solubility (Ks) of these compounds define their behavior in a physiological environment. Hydroxyapatite is the gold standard among calcium phosphate materials, but other chemical compositions/stoichiometries have also been studied for their interesting properties. The second part reviews the most usual deposition processes to produce bioactive calcium phosphate coatings for bone implant applications. Plasma spraying is the main industrial process, but magnetron sputtering, pulsed laser deposition, electrospray deposition, electrophoretic deposition, and electrodeposition are also widely studied in academic and industrial research. The last part describes the main physicochemical properties of calcium phosphate coatings and their impact on the bioactivity of bone implants in a physiological environment.

Large amounts of gas hydrate are present in marine sediments offshore Taitao Peninsula, near the Chile Triple Junction. Here, marine sediments on the forearc contain carbon that is converted to methane in a zone of very high heat flow and intense rock deformation above the downgoing oceanic spreading ridge separating the Nazca and Antarctic plates. This regime enables vigorous fluid migration. Here we present an analysis of the spatial distribution, concentration, estimate of gas phases (gas hydrate and free gas) and geothermal gradients in the accretionary prism and forearc sediments offshore Taitao (45.5° - 47° S). Velocity analysis of Seismic Profile RC2901-751 indicates gas hydrate concentration values <10% of the total rock volume, and extremely high geothermal gradients (<190 °Ckm^-1). Gas hydrates are located in shallow sediments (90-280 meters below the seafloor). The large amount of hydrate and free gas estimated (7.21x10¹¹ m³ and 4.1x10¹⁰ m³, respectively), the high seismicity, the mechanically unstable nature of the sediments, and the anomalous geothermal conditions, set the stage for potential massive releases of methane to the ocean mainly through hydrate dissociation and/or migration directly to the seabed through faults. We conclude that the Chile Triple Junction is an important methane seepage area and should be the focus of novel geological and ecological research.

Background: Pediatric ureteropelvic junction obstruction (UPJO) is a common urinary tract issue. Accurate assessment of postoperative kidney function is crucial for prognosis. Previous studies mainly focused on postoperative renal function and individual factors. Radionuclide imaging was costly and unsuitable for long-term follow-up. For aligning closely with clinical needs, we emphasizing renal morphology enhancement, and comprehensively analyzed factors influencing UPJO surgery outcomes. Methods: We retrospectively studied 150 pediatric UPJO patients (July 2012-July 2022) with severe anteroposterior renal pelvis dilation (APD grades 4-5) who underwent laparoscopic dismembered pyeloplasty. Demographics, symptoms, preoperative findings, and postoperative renal ultrasounds were assessed. We performed multivariable logistic regression analysis to identify significant predictors of prognosis and construct a regression model. Results: Among the 150 pediatric patients, 78 (52%) showed improvement in renal morphology after surgery. In the multivariate logistic regression analysis, age at surgery, duration of hydronephrosis, body weight, and preoperative creatinine were identified as significant prognostic factors for postoperative outcomes. The nomogram (AUC: 0.92) was constructed based on these factors and could serve as a useful tool for clinicians in evaluating the surgical prognosis of children with UPJO. Conclusions: This study reveals that among pediatric patients with severe hydronephrosis resulting from UPJO, those who are younger, have a shorter duration of illness, normal serum creatinine levels, and a healthy body weight tend to experience better postoperative recovery. This finding emphasizes the importance of adopting more proactive clinical interventions when managing such cases, with the goal of achieving enhanced recovery outcomes for affected children.

Distinguishing circular RNA (circRNA) reads from reads derived from the linear host transcript is a challenging task because of sequence overlap. We developed a computational approach, CiLiQuant, that determines the relative circular and linear abundance of transcripts and gene loci using backsplice and forward splice junction reads generated by existing mapping and circRNA discovery tools.

The response of the Cold-Electron Bolometers (CEBs), integrated into a 2-D array of dipole antennas, has been measured by irradiation from YBa$_2$Cu$_3$O$_{7-\delta}$ (YBCO) 50 $\mu$m long Josephson junction into the THz region at frequencies from 0.1 to 0.8 THz. The possibility of controlling the amplitude-frequency characteristic is demonstrated by the external magnetic field in the traveling wave regime of a long Josephson junction. YBCO junction has been formed on the bicrystal Zr$_{1-x}$Y$_x$O$_2$ (YSZ) substrate by magnetron sputtering and etching of the film. CEBs have been fabricated using an Al multilayer structure by a self-aligned shadow evaporation technique on Si substrate. Both receiver and oscillator have been located inside the same cryostat at 0.3K and 2.7K plates, respectively.

This paper proposes a novel method for optimizing the Cauer-type thermal network model considering both the temperature influence on the extraction of parameters and the errors caused by the physical structure. In terms of prediction of the transient junction temperature and the steady-state junction temperature, the parameters of conventional Cauer-type are modified, and the general method for estimating junction temperature is studied by using the adaptive thermal network model. The results show that junction temperature estimated by adaptive Cauer-type thermal network model is more accurate than that of the conventional model.

Surface treatment of implants facilitates osseointegration, with nanostructured surfaces exhibiting accelerated peri-implant bone regeneration. This study compared bone-to-implant contact (BIC) in implants with hydroxyapatite (HA), sand-blasted and acid-etched (SLA), and SLA with calcium (Ca)-coated (XPEED®) surfaces. Seventy-five disk-shaped grade 4 Ti specimens divided into three groups were prepared, with 16 implants per group tested in New Zealand white rabbits. Surface characterization was performed using X-ray diffraction (XRD), field emission scanning electron microscopy (FE-SEM), digital microscopy, and a contact angle analyzer. Cell viability, proliferation, and adhesion were assessed using MC3T3-E1 cells. Apatite formation was evaluated using modified simulated body fluid (m-SBF) incubation. After 4 weeks of healing, the outcomes reviewed were BIC, bone area (BA), removal torque tests, and histomorphometric evaluation. Microstructure analysis revealed irregular pores across all groups, with the XPEED group exhibiting a nanostructured Ca-coated surface. Surface characterization showed a crystalline CaTiO3 layer on XPEED surfaces, with evenly distributed Ca penetrating the implants. All surfaces provided excellent environments for cell growth. The XPEED and SLA groups showed significantly higher cell density and viability with superior osseointegration than HA (p &lt; 0.05); XPEED exhibited the highest absorbance values. Thus, XPEED surface treatment improved implant performance, biocompatibility, stability, and osseointegration.

The present review compared the efficacy of soft tissue substitutes (STS) and autogenous free gingival graft (FGG) or connective tissue graft (CTG) in mucogingival procedures to increase keratinized tissue (KT) width around teeth and implants. Two independent examiners performed the electronic search on Medline and Cochrane Library based on the following PICO’s format: (P) adult patients; (I) soft tissue substitutes and FGG/CTG; (C) STS vs CTG; STS vs FGG; STS vs CTR; (O) KT width gain; (S) Systematic Reviews, Randomized Controlled Trials. Results showed that around teeth, all biomaterials showed superior performance compared to CAF alone for treating gingival recessions. However, when compared to CTG, ADM yields the most similar outcomes to the gold standard (CTG), even though in multiple recessions CTG still continue to be considered the most favorable approach. Use of STSs (acellular matrix or tissue engineered) in combination with an apically positioned flap resulted in a significantly less gain of KTW compared to what achieved with FGG and APF. Around dental implants, free gingival grafts were deemed more effective than soft tissue substitutes in enhancing keratinized mucosa width.

Breast cancer is the most common cancer in women globally, often necessitating mastectomy and subsequent breast reconstruction. Silicone mammary implants (SMIs) play a pivotal role in breast reconstruction, yet their interaction with the host immune system and microbiome remains poorly understood. This study investigates the impact of SMI surface topography on host antimicrobial responses, wound proteome dynamics, and microbial colonization. Biological samples were col-lected from ten human patients undergoing breast reconstruction with SMIs. Mass spectrometry profiles were analyzed for acute and chronic wound proteomes, revealing a nuanced interplay between topography and antimicrobial respondseproteins. 16S rRNA sequencing assessed mi-crobiome dynamics, unveiling topography-specific variations in microbial composition. Surface topography alterations influenced wound proteome composition. Microbiome analysis revealed heightened diversity around rougher SMIs, emphasizing topography-dependent microbial inva-sion. In vitro experiments confirmed staphylococcal adhesion, growth, and biofilm formation on SMI surfaces, with increased texture correlating positively with bacterial colonization. This comprehensive investigation highlights the intricate interplay between SMI topography, wound proteome dynamics, and microbial transmission. The findings contribute to understanding host-microbe interactions on SMI surfaces, essential for optimizing clinical applications and minimizing complications in breast reconstruction.

The clinical application of Phentolamine Mesylate (PM) as an anaesthetic reversal agent has been documented in paediatric patients and in conservative dentistry, but no studies have been found in implant surgery. A prospective randomised study was conducted in 60 patients eligible for mandibular implant treatment, randomly divided between the Control Group (CG) and Experimental Group (EG), who were administered PM. Haemodynamic changes, adverse effects and patient satisfaction were assessed. No statistically significant differences in haemodynamic changes and postoperative pain were found between CG and EG (p&lt;0.05), except for Systolic Blood Pressure (SBP) which increased slightly in EG, without posing a risk to the patient. There were no differences in the presence of adverse effects between the two groups, except in the CG which presented greater difficulty in chewing and biting (p&lt;0.05) and the EG with greater pain in the injection area (p=0.043). 83.3% of the EG patients would request PM again for future dental treatment. The use of PM offers an alternative in implant surgery, without increasing the risks and increasing the patient's quality of life.

Medical implants made of biodegradable materials could be of advantage for temporary applications such mechanical support during bone-healing or as vascular stents to keep blood vessels open. After completion of the healing process the implant would disappear, avoiding long-term side effects or the need for surgical removal. Various corrodible metal alloys based on magnesium, iron or zinc have been proposed as sturdier and potentially less inflammatory alternative to degradable organic polymers, in particular for load-bearing applications. Despite the recent introduction of magnesium-based screws the remaining hurdles to routine clinical applications are still challenging, such as limiting mechanical material characteristics or unsuitable corrosion characteristics. Here, salient features and clinical prospects of currently investigated biodegradable implant materials are summarized with a main focus on magnesium alloys. A mechanism of action for the stimulation of bone growth due to the exertion of mechanical force by magnesium corrosion products is discussed. To explain divergent in vitro and in vivo effects of magnesium a novel model for bacterial biofilm infections is proposed which predicts crucial consequences antibacterial implant strategies.

Currently the bimatoprost implant (DURYSTA) is approved for a single administration secondary to concern for progressive corneal endothelial cell (CEC) loss with intracameral administration. In order to better understand the cause of CEC loss and other adverse events (AEs) with intracameral administration, multimodal imaging of the implant utilizing optical coherence topography (OCT), robotic ultrasound and bio microscopy video recording was utilized. Inherently the anterior chamber is a non-confined space. In certain examples the implant assumed a round and spotted structure as it picked up iris pigment as it migrated around the anterior chamber. Accordingly, we explored delivery of the implant in the middle segment behind the iris and in front of the pseudophakic lens. We then evaluated the suitability of various imaging modalities to assess the implant in this location. For middle segment administration, the ArcScan Insight 100 robotic ultrasound provided resolution and repeatability sufficient to monitor the implant behind the iris. This preliminary study hypothesizes that DURYSTA migration in the anterior chamber is the main source of AEs. Through use of a confined location, the middle segment, the implant is unlikely to migrate and cause CEC loss while also delivering drug closer to its site of action, the ciliary body. Further efforts are underway to understand the suitability of the middle segment for serial DURYSTA administration to maximize intraocular pressure lowering while minimizing AEs.

Connexins (Cxs) are transmembrane proteins that assemble into gap junction channels (GJCs) and hemichannels (HCs). Previous research supports the involvement of Rho GTPases and actin microfilaments in the trafficking of Cxs, formation of GJCs plaques, and regulation of channel activity. Nonetheless, it remains uncertain whether distinct types of Cxs HCs and GJCs respond differently to Rho GTPases or changes in actin polymerization/depolymerization dynamics. Our investigation revealed that inhibiting RhoA, a small GTPase that controls actin polymerization, or disrupting actin microfilaments with cytochalasin B (Cyto-B), resulted in reduced GJCs plaque size at appositional membranes and increased transport of HCs to non-appositional plasma membrane regions. Notably, these effects were consistent across different Cx types, since Cx26 and Cx43 exhibited similar responses despite having distinct trafficking routes to the plasma membrane. Functional assessments showed that RhoA inhibition and actin depolymerization decreased the activity of Cx43 GJCs while significantly increasing HCs activity. However, the functional status of GJCs and HCs composed of Cx26 remained unaffected. This study supports the hypothesis that RhoA, through its control of the actin cytoskeleton, facilitates the transport of HCs to appositional cell membranes for GJCs formation while simultaneously limiting the positioning of free HCs at non-appositional cell membranes, independently of Cx type. This dynamic regulation promotes intercellular communication and reduces non-selective plasma membrane permeability through a Cx-type dependent mechanism, whereby Cx43 HCs and GJCs are affected, but Cx26 channels are not.

Background: The treatment plan of prosthetic restorations supported by dental implants require comprehensive scientific knowledge to deliver prostheses with good prognosis, even before the implant insertion. This review aims to analyze the main prosthetic determinants of the prognosis of implant-supported prostheses. Methods: A systematic review of the literature was conducted with a PICO question: "For partially or complete edentulous subjects treated with implant-supported prostheses, which prosthetic factors could affect clinical outcomes?". A literature search was performed electronically in PubMed (MEDLINE), Scopus and Cochrane Library with the following equation [PROGNOS* OR RISK] FACTOR IMPLANT DENTAL, and by hand search in relevant journals and throughout the selected papers. Results: This revision was carried out based on 50 papers focused on several prosthodontics-related risk factors that were grouped as follows: implant-connection, loading protocol, transmucosal abutments, prosthetic fit, provisionalization, type of retention, impression technique, fabrication technique, and occlusion. More than a half of the studies were systematic reviews (30%), meta-analysis (16%) or prospective evaluations of prosthesis with various kinds of events (18%). But also narrative reviews of literature (14%) and in vitro/animal studies (16%) were found. Conclusions: The current literature provides insufficient evidence for most of the investigated topics. However, based on the accumulated data, it seems reasonable to defend that the best treatment approach is the use of morse taper implants with transmucosal abutments, recorded by means of rigidly splinted copings through the pick-up technique, and screwed by milled prosthesis occlusally adjusted to minimize functional overloading.

This systematic review investigates the failure rate and marginal bone loss (MBL) of dental implants placed in Solid-organ transplant (SOT) patients compared to healthy controls. Three databases (PubMed, Web of Sciences and the Cochrane Library) were searched up to June 2020 (PROSPERO CRD42019124896). Case-control and cohort studies reporting data failure rate and marginal bone loss (MBL) of dental implants placed in SOT patients were included. The risk of bias of observational studies was assessed through the Newcastle-Ottawa Scale (NOS). Four case-control studies fulfilled the inclusion criteria, all of low risk of bias. Meta-analyses revealed consistently lower implant failure rate than control populations at patient and implant levels. SOT patients had a significant difference of -18% (p-value <0.001) of MLB towards healthy patients. SOT status poses no serious threat to implant survival. Overall, this group of patients presented lower levels of dental implant failure rate and marginal bone loss compared to otherwise healthy patients. Further intervention trials with wider sample size and longer follow-ups are necessary to confirm these summary results.

The continuous advancement of Artificial Intelligence (AI) technology depends on the efficient processing of unstructured data, encompassing text, speech, and video. Traditional serial computing systems based on the von Neumann architecture, employed in information and communication technology development for decades, not suitable for the concurrent processing of massive unstructured data tasks with relatively low-level operations. As a result, there arises a pressing need to develop novel parallel computing systems. Recently, there has been a burgeoning interest among developers in emulating the intricate operations of the human brain, which efficiently processes vast datasets with remarkable energy efficiency. This has led to the proposal of neuromorphic computing systems. Of these, Spiking Neural Networks (SNNs), designed to closely resemble the information processing mechanisms of biological neural networks, are subjects of intense research activity. Nevertheless, a comprehensive investigation into the relationship between spike shapes and Spike-Timing-Dependent Plasticity (STDP) to ensure efficient synaptic behavior remains insufficiently explored. In this study, we systematically explore various input spike types to optimize the resistive memory characteristics of Halfnium-based Ferroelectric Tunnel Junction (FTJ) devices. Among the various spike shapes investigated, the square-triangle (RT) spike exhibited good linearity and symmetry, and a wide range of weight values could be realized depending on the offset of the RT spike. These results indicate that the spike shape serves as a crucial indicator in the alteration of synaptic connections, representing the strength of the signals.

INTRODUCTION: Breast sensibility following reconstruction surgery, though often overlooked, holds significant importance due to its widespread occurrence and profound effects on patients’ well-being and safety. Our objective is to compare the sensory outcomes between DIEP flap microsurgery reconstruction and implant-based reconstruction. Additionally, we explored the potential influence of sociodemographic and clinical factors on sensory recovery, along with assessing temperature discrimination abilities and evaluating quality of life. MATERIAL AND METHODS: We conducted an ambispective descriptive-analytical study, involving women who underwent mastectomy with reconstruction using either DIEP flap and implants at our hospital between 1990 and 2021. Data were collected from medical records, patient histories, physical examination, and validated quality of life questionnaires (BREAST-Q). RESULTS: A total of 99 women with breast reconstruction were included, 47 with DIEP flap and 52 with implants. Sensory recovery in implant-based reconstruction was found to be superior to DIEP flap reconstruction (5.03 and 5.18 respectively, p-value &lt;0.005). A direct correlation was observed between sensory improvement and thermal discrimination (Spearman coefficient 0.9, p-value &lt;0.001). Factors such as radiotherapy, delayed reconstruction with DIEP flap, and height with implants were associated with poorer sensory recovery in the breast. Women experiencing better breast sensibility reported higher satisfaction with their surgeon, medical team, and psychosocial quality of life. CONCLUSION: Women reconstructed with implants or DIEP abdominal flap exhibit suboptimal overall sensory recovery of the reconstructed breast, with slightly better outcomes observed in women reconstructed with implants.

Recently, the indications for Cochlear Implant (CI) have also been extended to subjects with Single Sided Deafness (SSD) in order to restore binaural hearing. The primary objective of this study was to investigate the advantages of CI following one year of usage in SSD subjects. Secondarily we want to assess the long-term stability of the CI. 57 participants performed a complete audiological assessment (speech audiometry in quiet and in noise and localization test). For each was also evaluated subjective hearing profile (with Speech Spatial and Qualities_SSQ questionnaire) and the impact of tinnitus (with the use of Tinnitus Handicap Inventory_THI questionnaire) After one year of CI usage, we observed a significant improvement in speech-to-noise ratio, in sound localization abilities, in the Speech (p-value 0.001) and Spatial (p-value 0.001) subscales of the SSQ questionnaire and in THI questionnaire (p-value 0.001). The improvements in speech in noise and localization abilities and the reduction of the SSQ and THI questionnaires scores were maintained over time (6th to 60th month follow-up). Only eight participants did not fully utilize the CI. CI in SSD represents an effective method for improving speech recognition in noisy environments, restoring sound localization abilities, reducing tinnitus and improve subjective listening skills.

The objective of this study was to compare the distribution of stress in the maxillary bone, dental implants, and prosthetic components supporting implant-supported maxillary overdentures with partial palatal coverage, in both splinted and unsplinted designs. Two models of maxillary overdentures were designed using the Exocad Dental CAD program, which included cancellous and cortical bone. The complete denture design and abutments (locator abutments in the unsplinted and Hader bar with Vertix attachments placed distally in the splinted variant) were also designed. The denture material was PEEK (Polyetheretherketone), and the method used to analyze patient-specific 3D X-ray scans was 3D QCT/FEA (Three-dimensional Quantitative Computed Tomography-Based Finite Element Analysis). Loading was divided into three load cases: frontal region (both incisors of the denture) and distal region (both molars and first premolar of the denture). The forces applied were 150 N with an oblique component with a buccal inclination of 35° in the frontal region, and 600 N with a buccal inclination of 5° (molars) or solely vertical (premolar) in the distal region. The model with locator abutments showed higher stresses in all load cases in both analyzed implant variants and in the maxilla. The differences in stress distribution between the splinted and unsplinted variants were more significant in the distal region. According to the results of the present study, the amount of stress in bone tissue and dental implant parts was smaller in the splinted, bar-retained variant. The findings of this study can be useful in selecting the appropriate prosthetic design for implant-supported maxillary overdentures with partial palatal coverage.

The aim of this study was to analyze surgical and refractive outcomes of XEN glaucoma implant (Allergan, an Abbvie company, Irvine, CA, USA), a minimally invasive surgical device for the treatment of refractory glaucoma. A retrospective chart review of eyes that received XEN Gel Stent placement from December 2014 to October 2019 was conducted. Intraocular pressure (IOP) change, best corrected visual acuity (BCVA), change in glaucoma medications, frequency of slit lamp revision procedures, and frequency of secondary glaucoma surgeries were the primary outcomes. Seventy-two subjects were included in the study: 32 (44%) males and 40 (56%) females. The mean follow-up time was 26.87 ± 15.33 months. The mean IOP before surgery was 24.82 ± 8.03 mmHg and decreased to 17.45 ± 5.84 mmHg at the end of the study, MD = -7.48, CI95 [-10.04; -4.93], p < 0.001. The mean decrease from baseline was 23%. Before surgery BCVA was 0.38±0.30 and at the end of the follow-up period it had improved to 0.47±0.37, MD = 0.09, CI95 [0.04; 0.13], p < 0.001. Additional procedures (fluorouracil injection, Bleb needling) were performed in 11/72 patients (15%). Further glaucoma surgery was necessary for 23.9%% of the patients. Implantation of XEN Gel Stent is both safe and effective for lowering IOP in refractory glaucoma patients.

Some evidence supports the influence of the implant macro-design and primary stability. Additionally, tactile perception can be used to assess implant stability when placing the implant. This research aimed to quantify the primary and secondary stability of three implant systems with two different macro geometries (cylindrical and conical) determined through the insertion torque and the implant stability quotient (ISQ) at the moment of implant placement as a function of implant-related factors (length, width, dental arch, and implant location in the arch), intraoperative factors (bone density determined subjectively by the clinician's tactile perception), and patient-related factors (age, gender and bone density determined objectively in the cone beam computed tomography (CBCT). Methods: 102 implants of three implant systems with two different macro geometries (conical and cylindrical) were placed in 53 patients. The insertion torque, the ISQ at the implant placement (ISQ0), and bone quality according to the clinician's tactile sensation were recorded on the day of the surgery. After a three-month healing period, the ISQ was re-evaluated (ISQ3). Results: Cylindrical implants exhibited significantly higher insertion torque and ISQ at the moment of the surgery and after three months than conical implants. Cylindrical implants also showed significantly lower indices of tactile evaluation of bone quality during the implant placement surgery. However, no differences were demonstrated in the bone density measured objectively in the CBCT. (4) Conclusions: The cylindrical implants achieved the highest values for primary stability (Ncm and ISQ) and secondary stability (ISQ after three months). Insertion torque was the variable that most influenced ISQ on the day of the surgery. Implant location (incisors-canines, bicuspids-molars) and the implant macro geometry were the variables that most influenced the secondary stability (ISQ at three months).

A healthy 47-year-old woman consulted the Oral Surgery and Implantology Unit of the University Hospitals of Geneva with a request to treat her painful tooth 11 and replace the missing tooth 21. The dental history revealed that the patient had lost teeth 21 and 22 due to advanced caries. On clinical examination, tooth 11 showed an ill-fitting prosthetic crown with overhanging margins, an increased localized probing depth of 8 mm in the disto-vestibular area and sensitivity to percussion. The edentulous site 21 showed horizontal bone atrophy. Radiological examination revealed a well-defined unilocular radiotransparent lesion surrounded by a thin radiolucent border, located at the apex of tooth 11 and measuring 10 x 8 mm. The treatment consisted of extraction of 11, enucleation of the apical lesion, insertion of implants at sites 11 and 21 with simultaneous bone augmentation in a single surgical procedure with aesthetic and functional results at 3-year follow-up without any complications. Our case highlights that immediate implant placement in case of cystic periapical lesion represents a good valid alternative to standard treatment.

The type of implant at the fracture site has effects not only from biological perspective but also from mechanical perspective in fracture healing. Biodegradable implants such as magnesium (Mg) based alloys have shown faster secondary bone healing properties as compared to bioinert implants such as titanium (Ti). The general reasoning behind this is the benefit of Mg from biocompatibility perspectives. We study the effect of Ti and Mg as base materials for implants with their different mechanical properties. The focus of our work is on the displacements at the fracture site of the tibia and their influence on the stimulus for bone healing. We have found that in comparison to Ti, Mg implants have minimal stress shielding problem, only which led to better mechanical stimulus at the fracture site.

Deep ultraviolet (DUV) light emitting diode (LED) at emission wavelength of 254 nm is inevitable to replace the conventional toxic mercury UV Lamp as demanded by Minamata Convention of 2020. Both the conventional DUV LEDs (C-LED) and tunnel junction (TJ)-based UVC LEDs are suffering from high operating voltages, low hole injection efficiency and efficiency droops. Therefore, p-AlGaN and n-AlGaN layers-based TJ is one of the most promising parts of optical devices and has been widely utilized as carrier tunneling in DUV LEDs to mitigate both the contact resistance for Ohmic contact and low hole injection efficicny at 254 nm emission. Here an approach is presented to electrically manipulate the quantum tunneling probability by exploiting the transported carriers at the interface of n-AlGaN/p-AlGaN TJ with moderate Si and Mg-doping levels and optimized thickness. As a result, the Augur recomination rate was sucesfully suppressed and quite high radiative recombination rates were achived in the 254nm TJ-based DUV LEDs, which is attributed the improved holes injection toward the MQWs when compared to C-LED. The internal-quantum efficiency (IQE) of approximately ~ 88% in the TJ-based LED with zero efficiency droop is achived, which is 1.3 times greater than the IQE of approximately ~ 66% in the C-LED with efficiency droop of 53%. Based on our known knowledge, this is the highest reported IQE (88%) at emission wavelength of 254 nm in the AlGaN TJ-based LED with efficiency droop of 0%. It was found that the light output powers (LOP) of TJ-LED increases linearly under the varying current density, whereas in the case of C-LED the LOP changes nonlinearly under varying current density. This is attributed to the lower Augure recombination rate in the MQWs of TJ-based DUV LED. The operating voltages were remarkable reduced from 20 V to 5.4 V under 200 mA operation, which is attributed to the thickness and doping optimization in TJ and better selection of realively lower Al-content in the contact-layer. The demonstrated TJ-based DUV LEDs opens the door to epitaxial growth of high-performance UV emitters in MOCVD and MBE for a plethora of biomedical applications.

Today, dental implantology is a reliable technique for the treatment of partial and total edentulism. The fixing of dentures on dental implants can be achieved by a number of different techniques. The choice of technique depends on the specific needs of the patient, the condition of the jawbone and the design of the prosthesis itself. Currently, the two most common types of prosthetic abutment connections are cemented or screwed connections, both of which have disadvantages and ad-vantages. The aim of this study is to analyze, with Finite Element Analysis (FEA), a new Cone Morse connection system between the prosthesis and implant. The connection retention has been analyzed by adopting three different approaches: analytical, in vitro and the FEA method. The systems formed by abutment, healing-cap, and crown with three different inclination conditions were modeled in 3D: 0°, 15° and 30°. With Ansys finite element software, the effect of tilt on system retention was studied. The FEA analysis showed comparable results with in vitro studies regarding the retention strength for an abutment-cap system with a taper of 4°, obtaining 66.6 N compared to 68 N calculated through an in vitro study. The inclination of the abutment affects the retention of the system because the hole made on the surface of the abutment, decreases the contact area between the components. The Cone Morse prosthesis implant connection system is the most stable and efficient system compared to the threaded or cemented system. Retention is influenced by factors such as abutment conicity, insertion strength and the contact surface be-tween components.

(1) Background : When placing implants in the maxillary posterior region with insufficient alveolar bone, a maxillary sinus elevation is necessary. Autogenous bone, though biologically ideal, poses risks and discomfort due to donor site harvesting. Block-type autogenous tooth bone graft material, made from the patient’s own extracted tooth, offers similar biological stability without these drawbacks; (2) Methods : This study observed the progress of 19 implant patients who were treated with maxillary sinus elevation procedures using block-type autogenous tooth bone graft material at the Daegu Catholic University Medical Center. Extracted teeth were processed into demineralized tooth block bone. After elevating the sinus membrane, implants and the tooth bone graft material were placed in the space, and the bony window was repositioned. Postoperative evaluations through clinical observation and radiographic imaging assessed sinus membrane elevation, alveolar bone height increase, and implant osseointegration; (3) Results : Results showed proportional increases in alveolar bone height to the graft material size, with long-term stability. No postoperative complications occurred, even with sinus membrane perforation, and implants remained stable; (4) Conclusions : The study concludes that maxillary sinus lifts using block-type autogenous tooth bone graft material provide excellent bone induction and biocompatibility, making it a highly beneficial method for both dentists and patients.

Background: Restorative materials might significantly affect load transmission at peri-implant bone. The aim of the present study is to evaluate the shock absorption capacity of two different polymeric materials to be used as frameworks for implant-supported prostheses. Methods: A masticatory robot was used to compare the shock absorption capacity of polyether-ketoneketone (PEKK) Pekkton®ivory (Cendres+Mètaux) and glass fiber-reinforced composite (GFRC) TRINIATM (Bicon). Five identical sample crowns for each of the materials was tested un-der the same conditions described in previously published papers (Menini et al. 2013). Forces transmitted at the simulated periimplant bone were recorded and statistically analysed. Results: The statistical analysis of forces transmitted at the simulated dental implant revealed significant differences between all the materials tested and significant differences with the mate-rials tested in a previously published paper (Menini et al. 2013: zirconia, glass ceramic, composite resin, acrylic resin). Only differences between PEKK and veneered PEKK and between PEKK and one of the previously tested composite resins were not statistically significant. PEKK samples demonstrated significantly greater shock absorption capacity compared to GFRC. Conclusions: PEKK revealed optimal shock absorption capacity. Further studies are needed to evaluate its efficacy in case of long span prostheses with reduced prosthetic volume.

Background: This study aimed to evaluate survival rate, marginal bone levels, and full arch prosthetic success on short implants when placed in areas of severely resorbed and edentulous mandibles. Methods: This is a systematic review of all randomized controlled trials of at least 10 patients with a control group in which bone augmentations were performed that were published between January 2010 and February 2023. Only 3 relevant studies met the inclusion criteria. Results: It obtained demonstrate that short-term dental implant survival rates ranged from 94.2% to 97.4% with a 5-year follow-up and the prosthetic success rate varied by 62% during the same follow-up. The mean marginal bone level values ​​of the affected short implants ranged from 0.2 mm to 0.6 mm. Conclusions: The data obtained demonstrated that short dental implants positioned with criterion and precision as a full-arch fixed support are a valid therapeutic choice for the medium-long term rehabilitation of severe edentulous mandibular atrophy.

Denture wearers often complain about jeopardized function and reduced quality of life due to lack of prosthesis’ retention. Implant retained mandibular overdentures, on 2 non-connected implants (2IOD) are well-proven solutions to overcome these issues. We prospectively assessed 69 patients and scrutinized clinical records until at least 7 years of function. Thirty-six were retained on Locator ® Abutments (LA) and thirty-tree on Ball Abutments (BA). Both systems were compared regarding the type, amount and total cost of required maintenance. One implants was lost, yielding 98.7% survival after 7 years. In total 438 technical issues occurred: 121 (27.35%) in BA and 317 (72.4%) in LA. Out of these, 343 events (78%) were solved chairside: 191 (43.6%) were replacements of retention caps, 113 (25.8%) were minor acrylic repairs, in 26 (5.9%) pressure ulcers had to be relieved and 13 (3%) related to abutments. LA required 179 insert replacements compared to 12 in the BA group. The overall initial treatment cost was 3850 euro. The average total maintenance cost in relation to the initial cost for the LA and BA groups was 19.11% (range 0% - 82.24%) and 18.91% (range 0% - 113.26%) respectively (P=0.540). Conclusions: The 7-years maintenance costs for a 2IOD is acceptable when the patient is regularly checked and professionally maintained. Most events are easily solvable chairside, but a few patients required more expensive interventions, regardless of the type of attachment used.

Josephson junctions (JJs) in the presence of a magnetic field exhibit qualitatively different interference patterns depending on the spatial distribution of the supercurrent through the junction. In JJs based on two-dimensional topological insulators (2DTIs), the electrons/holes forming a Cooper pair (CP) can either propagate along the same edge or be split into the two edges. The former leads to a SQUID-like interference pattern, with the superconducting flux quantum $\phi_0$ (where $\phi_0=h/2e$) as a fundamental period. If CPs’ splitting is additionally included, the resultant periodicity doubles. Since the edge states are typically considered as being strongly localized, the critical current does not decay as a function of the magnetic field. Here we go beyond this approach and inspect a topological JJ in the tunneling regime featuring extended edge states. We consider the possibility that the two electrons of a CP propagate and explore the junction independently over length scales comparable with the superconducting coherence length. As a consequence of the spatial extension, we obtain a decaying pattern with different possible periods. In particular, we show that, if crossed Andreev reflections (CARs) are dominant and the edge states overlap, the resulting interference pattern features oscillations whose periodicity approaches $2\phi_0$.

In this review paper, an overview of radiation induced deep level defects in n-type 4H-SiC studied by junction spectroscopy techniques, is given. In addition to carbon vacancy (Vc), present in as-grown material already, we focus on the following deep level defects: silicon vacancy (VSi), carbon interstitial (Ci), and carbon antisite-carbon vacancy (Csi-Vc) pair. Recent advances in measurements by junction spectroscopy techniques that have led the progress toward better understanding of radiation induced defects are presented.

The circuitry of the summarized "floating" differential stages (FDS) based on complementary field-effect transistors with a control p-n junction (CJFET), intended for use in low-noise analog microcircuits, for example, operational amplifiers. The results of modeling the flow characteristics of one of the CJFET FDSs in the LTSpice XVII environment at low temperatures (down to -197 ⁰С) and exposure to a neutron flux in the range of 1e13 ÷ 1e15 n / cm² are presented.

Peri-implantitis continues to be one of the major reasons for implant failures. We propose a new approach for incorporating MTA into Zirconia implant surfaces with Nd:YAG laser and investigate the biological response of peri-implant cells as well as the microbiological response. Discs of Zirconia stabilized with Yttria and Titanium were produced according 4 tested groups: Nd:YAG laser textured Zirconia coated with MTA (Zr MTA); Nd:YAG laser textured Zirconia (Zr Textured); Zirconia and Titanium discs (Zr and Ti ). Contact profilometry was used to evaluate surface roughness. Human osteoblasts, gingival fibroblasts and S. oralis were cultured on samples. Cell adhesion and morphology, cell viability, cell differentiation markers and bacterial growth were assessed. Zr Textured roughness was significantly higher compared to all other groups. Cellular adhesion was observed at 1 day in all samples in both cell lines. Osteoblasts viability was lower in Zr MTA group, unlike fibroblasts viability was shown to be higher in Zr MTA group compared to Zr Textured group at 3 and 7 days. Osteocalcin and IL-8 release by osteoblasts were higher in Zr MTA. Zr Textured showed higher IL-8 values released by fibroblasts. No differences in S. oralis CFUs were observed between groups. The results suggest that Zirconia implant surfaces coated with MTA seems to promote fibroblasts proliferation and osteoblasts differentiation, however does not appear to have antibacterial properties.

Background: We aimed to explore microvascular changes evaluated with optical coherence tomography angiography (OCTA) in patients undergoing epiretinal membrane (ERM) pars-plana vitrectomy (PPV) combined with intravitreal Ozurdex implantation, compared with standard PPV. (2) Methods: Prospective interventional analysis on 25 eyes undergoing PPV+Ozurdex (Group A) and 25 eyes undergoing PPV alone. Best corrected visual acuity (BCVA) and OCTA parameters, such as vessel density (VD) of the superficial and deep capillary plexi (SCP and DCP) in the whole 6.4x6.4 mm and fovea area, were evaluated preoperatively and 3 months after surgery. (3) Results: Postoperative BCVA significantly improved in both groups. No cases of post-operative cystoid macular edema (CME) were reported in Group A vs. 2 eyes in Group B. In Group A we found a statistically significant increase of SCP’s VD in either the whole image (from 42.1±4.1 to 45.6±4.3 %, p=0.01) and the fovea image (from 38.5±7.5 to 41.7±4.2%, p=0.03). In Group B, we reported no significant variations in the SCP’s VDs. In the DCP, VD significantly increased only in the whole image in Group A. Stage 4 ERMs showed the greatest improvement in VD, especially in Group A. (4) Conclusions: In conclusion, intraoperative Ozurdex prompted a significant BCVA recover and limited the occurrence of postoperative CME compared to the standard procedure. Moreover, Ozurdex implant is associated with a better restoration of microvascular structure in either SCP and DCP.

Since the development of CBCT had been utilized in dentistry, the images of the CBCT can assist the surgeon to evaluate the anatomy carefully. Despite the value of the radiology evaluation, the implant procedures may require additional consideration rather than only evaluating the anatomical factors. The purpose of this study is to evaluate the predictability of using CBCT alone to plan for implant placement on the edentulous patient digitally CBCT images were analyzed by clinicians, measuring the ridge heights and widths of 4 selected implant sites in the maxillary and 2 selected implant sites in the mandibular arches for 91 patients planning for the implant-supported overdenture. (A total of 47 patients out of the 91 had completed the implant placement on the edentulous ridge, contributing to 55 upper and/or lower arches (136 dental implants). . Both predictabilities are low, implying the CBCT planning for implant placement on the edentulous ridge is not a good index and is insufficient to predict the surgical procedures as a solo method. The finding of this study indicates that digital planning by CBCT is insufficient to serve as an individual tool to predict implant procedures. Further information and evaluation must be considered for implant placement on the edentulous ridge.

Background - Mandibular flexion (MF) is a complex biomechanical phenomenon, which involves a deformation of the mandible, due mainly to the contraction of the masticatory muscles, and can have numerous clinical effects. The main aim of the current systematic review is to highlight the different factors that can increase MF, to help clinicians, identify patients to whom they should pay more attention. As a secondary outcome, we wanted to analyze the preventive measures and suitable techniques to be adopted to minimize the negative effects of this phenomenon on oral fixed rehabilitations. Methods - The review, which was carried out in accordance with the “Preferred Reporting Items for Systematic reviews and Meta-Analyses” (PRISMA) flowchart, was recorded in the “International Prospective Register of Systematic Reviews” (PROSPERO). As research questions, “Patient/Population, Intervention, Comparison and Outcomes” (PICO) questions were employed. Using the ROBINS-I technique, the risk of bias in non-randomized clinical studies was evaluated. Results - The initial electronic search identified over 1300 potential articles, of which 54 studies were included in this systematic review. Information regarding the relationship between MF and individual factors, mandibular movements, impression-taking and fixed rehabilitations were obtained. Conclusions – The studies included in this systematic review showed that MF is greater during protrusive movements, in the posterior areas of the lower jaw, and in patients with brachial facial type, greater jaw length, small gonial angle and less density, length and bone surface of the symphysis. The biomechanical effects of mandibular flexion on fixed restorations are debated. Prospective clinical and radiological observational studies should be conducted to evaluate the potential short-, medium- and long-term consequences of MF.

Surface chemistry evaluation plays a crucial role in assessing the efficacy of chemical decontamination products for titanium implants. This study aimed to investigate the effectiveness of chemical decontamination solutions in cleaning a contaminated dental implant surface and to evaluate the potential of combining Pluronic gel with hydrogen peroxide (NuBone®Clean) by evaluating pellicle disruption and re-formation on implant surfaces. In addition, ensuring safety with in- vitro and human testing protocols. X-ray Photoelectron Spectroscopy (XPS) was utilized for surface analysis. All the tested gels had some effect on the surface cleanness except for PrefGel®. Among the tested chemical decontamination candidates, NuBone®Clean demonstrated effectiveness in providing a cleaner titanium surface. Furthermore, none of the tested chemical agents exhibited any cytotoxic effects, and the safety assessment showed no adverse events. The results of this study highlight the significance of conducting comprehensive evaluations, encompassing safety and efficacy, before introducing new chemical agents for dental treatments. The findings suggest that NuBone®Clean shows potential as a chemical decontamination solution for implant surfaces. However, further investigation through randomized clinical trials is necessary. By adhering to rigorous testing protocols, the development of safe and efficient chemical decontamination strategies can be advanced, benefiting patients and promoting progress in the field of implant dentistry.

Direct intercellular communication, mediated by gap junctions formed by the connexin transmembrane protein family, is frequently dysregulated in cancer. Connexins have been described as tumour suppressors, but emerging evidence suggests that they can also act as tumour promoters. This feature is connexin- and tissue-specific and may be mediated by complex signalling pathways through gap junctions or hemichannels or by completely junction-independent events. Lung cancer is the number one cancer in terms of mortality worldwide, and novel biomarkers and therapeutic targets are urgently needed. Our objective was to gain a better understanding of connexins in this setting. We used several in silico tools to analyse TCGA data in order to compare connexin mRNA expression between healthy lung tissue and lung tumours and correlated these results with gene methylation patterns. Using Kaplan-Meier plotter tools, we analysed a microarray dataset and an RNA-seq dataset of non-small cell lung tumours in order to correlate connexin expression with patient prognosis. We found that connexin mRNA expression is frequently either upregulated or downregulated in lung tumours. This correlated with both good and poor prognosis (overall survival) in a clear connexin isoform-dependent manner. These associations were strongly influenced by the histological subtype (adenocarcinoma versus squamous cell carcinoma). We present an overview of all connexins but particularly focus on four isoforms implicated in lung cancer: Cx26, Cx30.3, Cx32 and Cx43. We further analysed the protein expression and localization of Cx43 in a series of 72 human lung tumours. We identified a subset of tumours that exhibited a unique strong nuclear Cx43 expression pattern that predicted worse overall survival (p=0.014). Upon sub-stratification, the prognostic value remained highly significant in the adenocarcinoma subtype (p=0.002) but not in the squamous carcinoma subtype (p=0.578). This finding highlights the importance of analysis of connexin expression at the protein level, particularly the subcellular localization. Elucidation of the underlying pathways regulating Cx43 localization may provide for novel therapeutic opportunities.

Implant-supported-screw-retained prostheses are really popular. Some of the most frequent complications have been mechanical complications. These include abutment screw loosening or even screw fracture. Using an intermediate abutment can offer several advantages. However, little literature has been found regarding how this affects the mechanical behavior of dental restorations. This study focuses on understanding the mechanical behavior of implant-supported restorations with a transepithelial component compared to those with a direct implant-supported restoration. It was carried out by using the Finite Element Method (FEM) and was experi-mentally validated. The results showed that in the case of transepithelial-supported restoration, the prosthetic screw mounted over the transepithelial component suffers higher stress than the one screwed directly to the implant. After applying a cyclic fatigue load, it is experimentally proven that, in the transepithelial-supported restorations, the fuse changes from being the screw that goes to the implant, to being the upper one. As a conclusion we can say that the use of an intermediate abutment in dental restoration not only provides better protection to the rest of the dental restoration but also allows easier repair in the event of a fracture. This can potentially lead to more efficient procedures and improved patient outcomes.

Dental implant fracture is closely connected to the stress buildup surrounding the implant system during static loading. In areas where the cross section of the implant rapidly changes or where the geometry of the implant system has discontinuities, stress concentrations arise. Therefore, the implant's design is crucial in preventing early failure of the implant system, including fracture, screw loosening, and increased leakage, in addition to reducing stresses at the implant-abutment interface. In the current work, three-dimensional (3D) models of mechanically connected Ti6Al4V implant systems in various dimensions were constructed. Finite Element Analysis (FEA) was used to conduct a stress study of the created implants under actual acting forces static loading conditions in accordance with ISO 14801. In the created models, design elements including implant screw type, thickness, and taper angle of abutment were modified in order to increase the longevity of the implants. The results show that the equivalent stress level is dramatically reduced from 596.22 MPa to 212.72 MPa in the implant model, which exhibit more homogeneous stress pattern under static loading conditions. Furthermore, the relatively smoother stress transmission observed in this model holds promise for the development of new implants capable of withstanding the forces encountered in the oral environment.

In implantology, among the key choices, to obtain predictable results, it is essential to establish, on the basis of radiographic examinations, the bone site where to insert the implants; these selected locations must be identified first on the mucosa and then on the cortical bone. Surgical guides represent a valid aid especially in complex cases with more than 3 or 4 implants, whereas in single implant cases they are rarely used. This study evaluates the clinical precision with which the implant sites, on the patient's mucosa, are identified in surgical procedures planned without any templates. The verification of this precision is carried out through thermo-printed templates with radiopaque references which could however help the clinician to identify these sites in a simple, rapid and economical way.

The success of total hip arthroplasty depends on the experience of the surgeon, and one of the ways the surgeon currently determines the final implant insertion depth is to listen to the change in audible pitch of the hammering sound. We investigated the use of acoustic vibration emissions as a novel method for insertion quality assessment. A non-invasive contact microphone-based measurement system for insertion depth estimation, fixation and fracture detection was developed using a simplified in vitro bone/implant (n=5). 2583 audio recordings were analysed in vitro to obtain energy spectral density functions. Out of the four main resonant peaks under in vitro conditions, broach insertion depth statistically correlates to increasing 3rd and 4th peak frequencies. Degree of fixation was also observed as higher goodness of fit (0.26-0.78 vs. 0.12-0.51 between two broach sizes, the latter undersized). Finally, however, the moment of fracture could not be predicted. A cadaver in situ pilot study suggests comparable resonant frequencies in the same order of magnitudes with the bone model. Further understanding of the signal patterns are needed for an early warning system diagnostic system for imminent fractures, bone damage, improving accuracy and quality of future procedures.

The first treatments with dental implants had low success rates (75%). Nowadays, oral rehabilitation with titanium dental implants has a high success rate (95-98%). The success rate significantly increases due to increased scientific knowledge about osseointegration, changes in surgical techniques, and the development of implant surface treatments. Despite the high success rate of implants, no protocol defines the time for the prosthesis to be installed and loaded after surgery. This work compares a new dental implant's primary (mechanical) and secondary (osseointegration) stability. Dental implant with micro- and nano-roughness surface was placed in 24 patients with a minimum of 35 N.cm and a maximum of 60 N.cm. Primary stability was quantified with a torque wrench and Ostell Mentor. The secondary stability 45 and 60 days after surgery was measured with Ostell. The results showed no statistical difference in secondary stability at 45 and 60 days postoperatively among implants. The success rate of dental implants can be associated with the surface morphology with micro and nano-roughness and the shape of the fillets of the implant threads. When the manufacturer's guidelines are followed, it is possible to prosthetically rehabilitate the patient with an implant 45 days after surgery.

Background and Objectives: Mechanical and biological complications can lead to system fracture or screw loss on dental implants. Narrow and regular platforms have been used without a consensus about the effect of distance the abutment from the prosthetic platform margin. The aim of this study is to evaluate different insertion torques in the deformation of tri-channel platform connections through two- and three-dimensional measurements with micro-CT. Materials and Methods: 164 implants were divided into groups (platform diameter and type): 3.5, 3.75, and 4.3 mm NP (Narrow Platform), and 4.3 mm RP (Regular Platform). Each implant-platform group was then divided into four subgroups (n = 10) with different torques: T45 (45 Ncm), T80 (80 Ncm), T120 (120 Ncm) and T150 (150 Ncm). The implant-abutment-screw assemblies were scanned and the images obtained were analyzed. Results: A significant difference was observed for the linear and volume measures between the different platforms (p &lt;0.01) and the different implant insertion torques (p &lt;0.01). Qualitative analysis suggested higher deformation resistance for the 3.75 NP compared to the 3.5 NP, and RP was more resistant compared to the NP. Conclusions: The 0.25-mm increment in the implant platform did not increase the resistance to the applied insertion torques; the 4.3-mm implant was significantly stronger compared to the 3.5-mm implant and the proposed micro-CT analysis was considered valid for both 2D and 3D analyses of micro gaps, qualitatively and quantitatively.

The effect of the different dental implants positioning region on the stress performance of the implant-supported prosthesis is not yet clear. This study evaluated the dental treatment with six dental implants in three different models and three different occlusal loading conditions, in terms of the biomechanical response of implants, prosthetic screw and maxilla, using three-dimensional finite element analysis. The finite element models were modelled containing external hexagon implants, as well as a Cobalt-Chromium superstructure. Three types of loads were applied: in the area of ​​the central incisors, first premolar and in the second molars. For the finite element simulations, the von-Mises stress peaks in the implant and in the surrounding cortical bone were analyzed. All recorded results reported higher values ​​for the implant-supported prosthesis in group C compared to the groups A and B. The highest stress values, ​​regardless the evaluated model, was in the prosthesis in group C and in screws, the smallest were in group A.

Shiga toxin-producing Escherichia coli (STEC) are notorious foodborne pathogens capable of causing severe diarrhea and other life-threatening complications in humans. Cattle remain a major reservoir and asymptomatic carriers of STEC. In reservoir animals, the rectoanal junction (RAJ) serves as the primary colonization site of STEC playing a critical role in its transmission to humans through contaminated food sources. However, the molecular mechanisms behind the adaptation of STEC in the RAJ of the asymptomatic reservoir host and its subsequent infection of human colonic epithelial cells in an event of a foodborne transmission to cause diarrhea remain largely unexplored. This study aimed to unravel the intricate dynamics of STEC O157:H7 serotype in these two distinct host environments: bovine RAJ cells and human colonic epithelial cells, during initial colonization. In this context, comparative transcriptomics analysis was employed to investigate the differential gene expression profiles of STEC O157:H7 during its interaction with these cell types. The bacterial cells were cultured under controlled conditions to simulate the microenvironments of both bovine RAJ and human colonic epithelial cells. Using high-throughput RNA sequencing, we identified key bacterial genes and regulatory pathways that were significantly modulated in response to each specific host environment. Our findings reveal distinct expression patterns of bacterial genes involved in virulence, including adherence, metal iron homeostasis and stress response in STEC O157:H7 grown in bovine RAJ cells as op-posed to human colonic epithelial cells six hours post-infection. Additionally, the comparative analysis highlights the potential role of certain genes in host adaptation and tissue-specific pathogenicity. Furthermore, this study sheds light on the potential factors contributing to the survival and persistence of STEC O157:H7 in the bovine reservoir, and its ability to colonize in-testinal epithelium and cause disease in humans.

Deep-ultraviolet (UV) light-emitting diodes (LEDs) based on AlGaN crystals have low light-emission efficiency; therefore, there is a need to improve this light-emission efficiency for a wide range of applications such as water and air sterilizations. UV-light-transparent device structures are considered one of the many solutions toward increasing light output power. To this end, the present study focused on developing a transparent AlGaN-based tunnel junction (TJ) as the anode of a deep-UV LED. Deep-UV LEDs composed of n+/p+-type AlGaN TJs were fabricated under the growth condition that reduced the carrier compensation in the n+-type AlGaN layers. The operating voltage was 10.8 V under the direct current (DC) operation of 63 A/cm2. In addition, magnesium zinc oxide (MgZnO)/Al reflective electrodes were fabricated to enhance the output power of the AlGaN homoepitaxial TJ LED. The output power was 57.3 mW under a DC operation of 63 A/cm2, and it was 1.7 times higher than that realized using the conventional Ti/Al electrodes. The combination of the AlGaN-based TJ and MgZnO/Al reflective contact allows further improvement of the light output power. This study confirms that the AlGaN TJ is a promising UV-transmittance structure that can obtain a high light-extraction efficiency.

The clinical requirement for a good esthetic result for immediate implant placement is the absence of dehiscence in the anterior facial alveolar bone. In the presence of a dehiscence, it is recommend-ed to use a connective tissue graft in addition to immediate implant placement or to change to ear-ly implant placement. However, the literature focusing on dehiscence is scarce, and the influence of different placement times and combined use of connective tissue graft on postoperative esthetics in cases with dehiscence is unclear. Therefore, we quantitatively evaluated the pre-extraction de-hiscence morphology and postoperative changes in the facial tissue of implants in three groups: immediate implant placement (Group I), immediate implant placement with connective tissue graft (Group IC), and early implant placement (Group E). Fifty-two implants were obtained (20 in Group I, 16 in Group IC, and 16 in Group E). A wider dehiscence increases the risk of soft tissue regression, which was one reason for choosing early implant placement. A combination of imme-diate implant placement and connective tissue graft, or early implant placement, tended to result in less soft tissue regression due to the thicker postoperative facial soft tissue volume.

Chlorhexidine digluconate (CHX) has shown the ability to significantly reduce inflammation and marginal bone loss (MBL) at 1-year follow-up but limited data exists regarding its long-term efficacy in peri implant stability. The objective was to compare the long-term effects of a placebo gel (16 patients in Group A) or a 0.20% CHX gel (15 patients in Group B) used at each previous surgical and prosthetic stage. Follow-ups were conducted in 2022, investigating by biological, radiological, clinical, mechanical evaluation the long-term effects. Data were statistically analyzed. The research achieved a 96.7% implant success rate over five years, but 41.9% of patients didn't attend annual oral hygiene check-ups. The average MBL was 1.04 ± 0.39 mm, with no significant differences between the two groups. Notably, patients who attended regular periodontal check-ups experienced significantly less MBL than those who didn't (p &lt;0.05). At five years, the effects of CHX were reduced, with both groups showing moderate bone loss. The results suggest early disinfection could enhance both short and long-term outcomes. In fact, patient with initial minor MBL preserve this advantage also at 5 years of follow-up. Additionally, the data underscore the importance of annual check-ups in early detection and management of biological and mechanical complications.

Growth-preserving instrumentation techniques are utilized in early-onset scoliosis (EOS) cases requiring surgical intervention. Shilla technique corrects the deformity and may reduce the need for surgical treatment with its growth-directing effect. As with other techniques, various prob-lems can be encountered following the administration of the Shilla technique. The aim of this study was to examine the effect of complications encountered with Shilla treatment on correction and growth. Sixteen patients with a follow-up period of at least 1 year who received Shilla growth guidance for EOS were included in the study. No complications occurred in 50% cases and no unplanned surgery was required. Of the remaining 8 patients with postoperative im-plant-related complications (50%), 6 (37.5%) required unplanned surgery; this consequently caused implant failure in the proximal region in 5 cases (31.25%) and deep tissue infection around the implant in 1 case (6.25%). Deformity correction, spine length, and quality-of-life scores significantly improved in EOS through Shilla growth guidance. Although implant-related com-plications were observed and related unplanned surgeries were required with Shilla growth guidance in our patients, these complications did not have a significant negative effect on correc-tion and spine growth.

The aim of this study is to investigate the effect of two antiglaucoma procedures, namely trabeculectomy and Ex-PRESS mini-shunt insertion on the biomechanical properties of the cornea. This is a prospective study. Thirty patients (30 eyes) were included in the study. Nineteen eyes had an Ex-PRESS shunt inserted (Group 1) and 11 had trabeculectomy (Group 2). The examination time points for both groups were 1 to 3 weeks preoperatively and at month 1, 6 and 12 postoperatively. Corneal biomechanical properties [corneal hysteresis (CH) corneal resistance factor (CRF)] were measured with the Ocular Response Analyzer. In group 1, CH was significantly increased at 6 and 12 months compared to baseline values. Corneal hysteresis was also higher at 1 month postoperatively but this increase did not reach statistical significance. In group 2, the CH was significantly increased at all time points compared to the preoperative values. CRF decreased at all time points postoperatively compared to the preoperative values in both groups. The difference (preoperative values to postoperative values at all time points) of the CH and CRF between the two groups was also compared and no significant differences were detected between the two surgical techniques. Trabeculectomy and the EX-PRESS mini-shunt insertion alter significantly the corneal biomechanical properties as a result of the surgical trauma and the presence of the shunt in the corneal periphery. When compared between them they affect the corneal biomechanical properties in a similar way.

Cervical fusion has been a standard procedure for treating the abnormalities associated with the cervical spine. However, the reliability of anterior cervical discectomy and fusion (ACDF) has become arguable due to its adverse effects on the biomechanics of adjacent segments. One of the drawbacks associated with ACDF is adjacent segment degeneration (ASD) which has served as the base for the development of dynamic stabilization systems (DSS) and total disc replacement (TDR) devices for cervical spine. However, the hybrid surgical technique has also gained popularity recently but their effect on the biomechanics of cervical spine is not well researched. Thus, the objective of this FE study was to draw the comparison among single, bi-level and hybrid surgery with DCI implant with traditional fusion. Reduction in range of motion (ROM) for all the implanted models was observed for all the motions except extension, compared to intact model. The maximum increase in ROM of 42% was observed at C5-C6 level in Hybrid-DCI model. The maximum increase in adjacent segment’s ROM of 8.7% was observed in multilevel fusion model. The maximum von Mises stress in the implant was highest for the multilevel DCI model. Our study also showed that the shape of DCI implant permits flexion/extension relatively more compared to lateral bending and axial rotation.

Variations in the implant thread shape and occlusal load behavior may result in significant changes in the biological and mechanical properties of dental implants and surrounding bone tissue. Most previous studies consider a single implant thread design, an isotropic bone structure, and a static occlusal load. However, the effects of different thread designs, bone material properties, and loading conditions are important concerns in clinical practice. Accordingly, the present study performs Finite Element Analysis (FEA) simulations to investigate the static, quasi-static and dynamic response of the implant and implanted bone material under various thread designs and occlusal loading directions (buccal-lingual, mesiodistal and apical). The simulations focus specifically on the von Mises stress, displacement, shear stress, compressive stress and tensile stress within the implant and the surrounding bone. The results show that the thread design and occlusal loading rate have a significant effect on the stress distribution and deformation of the implant and bone structure during clinical applications. Overall, the results provide a useful insight into the design of enhanced dental implants for an improved load transfer efficiency and success rate.

The highest efficiency solar cell won in the efficiency race does not always give the most excellent annual energy yield in the real world solar condition that the spectrum is ever-changing. The study of the radiative coupling of the concentrator solar cells implied that the efficiency could increase by the recycle of the radiative recombination generated by the surplus current in upper junction. Such configuration is called by a super-multi-junction cell. We expanded the model in the concentrator solar cell to non-concentrating installation. It was shown that this super-multi-junction cell configuration was found robust and can keep the maximum potential efficiency (50 % in realistic spectrum fluctuation) up to 10 junctions. The super-multi-junction cell is also robust in the bandgap engineering of each junction. Therefore, the future multi-junction may not be needed to tune the bandgap for matching the standard solar spectrum, as well as relying upon artificial technologies like ELO (Epitaxial lift-off), wafer-bonding, mechanical-stacking, and reverse-growth, but merely uses up-right and lattice-matching growth technologies. We have two challenging techniques; one is the optical cap layer that may be the directional photon coupling layer in the application of the photonics technologies, and another is the high-quality epitaxial growth with almost 100 % of the radiative efficiency.

Both types of surgical guides – with and without metal sleeves are founded beneficial in clinical studies. The aim of this in vitro study was to compare time of surgical procedure in dental implantology depending of used type of the surgical guide. Ten three dimensional (3D) printed models of lower jaws were prepared based on complete virtual model of patient clinical conditions with missing teeth 37, 46 and 47. Five of this models were used for implant sites preparation performed with use of surgical guide without metal sleeves and dedicated surgical kit, and next five were used for the same procedure performed with surgical guide with metal sleeves and dedicated surgical kit. Time of implant site preparation were measured and noted. Statistical analysis was performed using Student’s t test for independent samples. Difference of time in both groups were founded as statistically significant (t=-9.94; df =28; p=0.0000). Type of surgical guide is important factor which can impact on time of implant site preparation and all surgical procedure.

The article reports on a patient who required a cranial protection system.Using additive manufacturing techniques and surgical planning with the help of bio-models, a patient-specific bone implant solution was proposed that allows aesthetic restoration of the affected area and provides an adequate level of protection. In addition, through a comparative analysis with finite elements, the mechanical response to external actions of the medical device, printed with two materials: polymethylmethacrylate (PMMA) and polyether-ether-ketone (PEEK), is simulated. The tested materials have recognized biocompatibility properties, but their costs on the market differ significantly. The results obtained demonstrate the similarities in the responses of both materials. It offers the possibility that low-income people can access these devices, guaranteeing adequate biomechanical safety, considering that PMMA is a much cheaper material than PEEK.

Aim: the purpose of the present prospective, case series study were to report implant survival rate and marginal bone remodeling expected five years after loading using dental implants placed in in the daily practice. Material and Methods: this research was designed as an open-cohort, prospective case series study. Any completely or partially edentulous patients scheduled to receive at least one bone leve were considered eligible for this study. Primary outcomes were: cumulative implant (ISR) and prosthetic (PSR) survival rates, and any complications experienced up the five years follow-up. Secondary outcomes were: marginal bone remodeling, implant insertion torque, implant stability quotient (ISQ), and thickness of gingival biotype. Results: ninety consecutive patients (34 males and 56 females; mean age 53.2±15.4 years; range of 24–81 years), 243 implants were placed and followed for at least five years after loading (mean of 65.4±3.1 months; range of 60–72 months). The mean implant insertion torque was 42.9±4.8 Ncm (range from 15 to 45 Ncm). Overall, 83.5% of the implants (n=203) were placed with an insertion torque between 35 and 45 Ncm. At the one year follow-up, no drop-outs were recorded, but 17 patients (18.9%) with 18 restorations (12.6%) delivered on 34 implants (14%) were lost at the five years examination. At the five-year examination, six implants failed in six patients, resulting in a cumulative ISR of 97.5%. At the five-year follow-up, four prostheses failed (2.8%) resulting in a cumulative PSR of 97.2%. At the five-year examination, five complications were reported by five different patients, resulting in a prosthetic success rate of 96.5%, measured at patient level. Five years after loading, mean MBL was 0.41 ± 0.30 mm (95% CI: 0.26–0.34). Difference from the one year data was 0.04 ± 0.19 mm (95% CI: 0.01–0.07). The mean ISQ value at implant placement was 71.6 ± 5.5 (range of 45–88). Six months later, the mean ISQ was 76.7 ± 4.4 (range of 66–89). The difference was statistically significant (P=0.0001). Statistically significant higher MBL was found for smokers, and patient with thin gingival biotype. Conclusions: High implant survival and success rates could be expected with stable marginal bone remodeling up to five years after loading. Smoking and thin tissue biotype were the most important variabilities associated with higher MBL. Further research are needed to confirm these results.

Background: By using outcome prediction scores, it is possible to distinguish between good and poor performers with cochlear implants (CI) after CI implantation. The reasons for poor performance, despite good basic conditions, can be manifold. On the one hand, the postoperative fitting may be inadequate; on the other, neurophysiological disease processes may impair speech understanding with a CI. These disease processes are not yet fully understood. In acoustics, it is known that the auditory brainstem responses (ABR) and their latencies and amplitudes allow differential diagnosis based on reference values for normal-hearing individuals. The aim of this study was to provide reference values for electrically evoked brainstem responses (EABRs) in terms of rate-dependent latencies and amplitudes. Methods: 20 experienced adult CI recipients with a predicted and measured good postoperative word recognition score were recruited from the clinic’s patient pool. In the same stimulation mode and intensity we measured latencies and interpeak-latencies of EABRs and electrically evoked compound action potentials (ECAPs). With a defined supra-threshold stimulation intensity above the individual ECAP threshold, we applied stimulation at several rates between 11 and 91 stimuli per second. Results: We found rate dependences for EABR latency t3 and t5 in the order of 0.19 ms and 0.37 ms respectively, while ECAP was not affected by rate. Correspondingly, the interpeak intervalls’ rate dependences for t5-t1, t5-t3 and t3-t1 were of the order of 0.37 ms, 0.18 ms and 0.19 ms. Comparing the EABR amplitudes between the stimulation rates 11/s and 81/s, we found that at 81/s the amplitudes were significantly reduced down: to 73% for A3 and 81% for A5. These rate dependences of latency and amplitude in EABR have characteristics comparable to those of acoustic ABR. Conclusions: These data may serve to provide reference values for EABR and ECAP latencies, interpeak intervals and amplitudes with respect to stimulation rate. Altered response patterns of ECAPs and EABRs to normalised stimulation modes could be used in the future to describe and classify neuropathological processes in a better-differentiated way.

Background: To compare the loss of preload in absence of loading and after a fixed number of ideal masticatory cycles in two different connection systems using all-on-four prosthetic model. Methods: Two equal models of an edentulous mandible rehabilitated with all-on-four technique with two types of abutment system (MUA and OT-Bridge) supporting a hybrid prosthesis, were used. Initial torque values of the prosthetic fixing screw, after ten minutes from initial screw tightening and after 400000 masticatory cycles were registered using a mechanical torque gauge. Differences between initial and final torque values were reported for each anchoring system and the two systems were finally compared. Results: No statistically significant differences regarding the loss of preload between MUA and OT-Bridge system were found after 400000 masticatory cycles; however, in MUA system it was found between anterior and posterior implant screws. A significant difference in preload loss was found only for MUA system comparing the initial screw torque to that measured after 10 minutes from the tightening in absence of cyclic loadings. Conclusions: MUA and OT-Bridge are reliable prosthetic anchoring systems able to tolerate repeated masticatory cycles also on distal cantilever in all-on-four rehabilitation model without any significant loss of preload in screw tightening

The most common long-term complication of silicone breast implants (SMI) remains capsular fibrosis. The etiology of this exaggerated implant encapsulation is multifactorial but primarily induced by the host response towards the foreign material silicone. Identified risk factors included specific implant topographies. Of note, breast implant-associated anaplastic large cell lymphoma (BIA-ALCL), has only been observed in response to textured surface implants. We hypothesize that reduction of SMI surface roughness causes less host response hence better cosmetic outcome with fewer complications for the patient. A total of 7 patients received the routinely used CPX®4 breast expander (~60 µM Ra) and the novel SmoothSilk® (~ 4 µM Ra), fixed prepectoral with a titanised mesh pocket and randomized to the left or right breast after bilateral prophylactic NSME (nipple-sparing mastectomy). We aimed to compare the postoperative outcome regarding capsule thickness, seroma formation, rippling, implant dislocation as well as comfortability and practicability. Our analysis shows that surface roughness is an influential parameter in controlling fibrotic implant encapsulation. First time intra-individually compared in patients, our data confirm an improved biocompatibility with minor capsule formation around SmoothSilk® implants with an average shell roughness of 4 µM and in addition an amplification of host response by titanised implant pockets.

Background: Implant surface topography is a key element in achieving osseointegration. Nanostructured surfaces have shown promising results in accelerating and improving bone healing around dental implants. The main objective of the present clinical and histological study is to compare, at 4 and 6 weeks, (w) bone-to-implant contact in implants having either machined surface (MAC), SLA medium roughness surface or a Nanostructured Calcium-Incorporated sur-face (XPEED®). Methods: 35 mini-implants with 3 different surface treatments (XPEED® (n=16) – SLA (n=13) – Machined (n=6), were placed in the posterior maxilla of 11 patients then, retrieved at either 4 or 6w in a randomized split-mouth study design. Results: The BIC rate measured at 4 and 6w respectively, was: 16.8 % (±5.0) and 29.0 % (±3.1) for MAC surface; 18.5 % (±2.3) and 33.7 % (±3.3) for SLA surface; 22.4 % (±1.3) and 38.6 % (±3.2) for XPEED® surface. In all types of in-vestigated surfaces, the time factor appeared to significantly increase the BIC rate (p < .05). XPEED® surface showed a significantly higher values when compared to both SLA and MAC values at 4w (p < .05). Also, at 6w, both roughened surfaces (SLA and XPEED® ) showed signifi-cantly higher values (p < .05) than turned surface (MAC). Conclusion: Nanostructured Calcium titanate coating is able to enhance bone deposition around implants at early healing stages.

Background: Perioperative treatment is a gold standard in locally advanced gastric cancer or GEJ cancer in western population. Unfortunately, the response rate after neoadjuvant chemotherapy (NAC) remains limited. Moreover, there are currently no biomarkers enabling an individual prediction of therapeutic efficacy. The aim of this study was identification of serum biomarkers of early response to NAC. Methods: We conducted this prospective study in the MSCNRIO, in Warsaw, Poland. A total of 71 patients and 15 healthy volunteers signed informed consent. Complete blood count, blood chemical tests, carcinoembryonic antigen (CEA) carcinoma antigen 125 (CA125), carcinoma an-tigen 19.9 (CA19.9), d-dimer, fibrinogen (F) were measured at baseline and before every cycle. Circulating tumour cells (CTCs) and interleukin-1β (IL-1β), interleukin-6 (IL-6), interleukin-8 (IL-8), interleukin-10 (IL-10) were measured in a pilot group of 40 patients at baseline and before cycle two (C2) and cycle three (C3). Results: Of all the measured parameters, only IL-6 serum level was statistically significant. The IL-6 level before C2 of chemotherapy was significantly decreased in complete pathological re-sponse (pCR) vs non-pCR group (3.71 pg/mL vs 7.63 pg/mL, p=0,004). In all patients with IL-6 levels below 5.0 pg/mL in C2, tumour regression TRG1a/1b according to Becker classification and ypN0 were detected in postoperative histopathological specimens. The IL-6 level before C1 of chemotherapy was significantly elevated in ypN+ vs ypN0 (7.69 pg/mL vs 2.89 pg/mL, p=0.022). Conclusions: The trial showed that elevated level of IL-6 prior to treatment and C2 might be a predictor of pathologic response to NAC.

Achievement of solid fusion of the lumbosacral junction (L5-S1 level) is an important factor in adult spinal deformity (ASD) surgery. The purpose of this study is to explore the effectiveness and feasibility of injectable rhBMP-2 (a combination of Eschericia coli-derived rhBMP-2 and hydrogel type β-TCP carrier; NOVOSIS Inject) as a bone substitute for the fusion of lumbosacral junction. 20 patients (average age 69.1 years) diagnosed with ASD with sagittal imbalance who underwent surgical treatment including anterior lumbar interbody fusion (ALIF) in the L5-S1 level were evaluated. Injectable rhBMP-2 was applied in L5-S1 ALIF and followed-up for 1-year. Solid fusion rates and changes of clinical outcomes (Oswestry Disability Index [ODI], Visual Analog Scale [VAS] of back and leg) were measured and analyzed at 6 and 12 months after surgery. All postoperative adverse events were evaluated about the association with injectable rhBMP-2. Fusion rates were 68.4% and 100% at 6 and 12 months after surgery. Compared to baseline, ODI were improved to 45.8% and 63.7%, VAS(back) were improved to 69.2% and 72.8%, and VAS(leg) were improved to 49.2% and 64.8% at 6 and 12 months after surgery (p&lt;0.001, respectively). There were no adverse events associated with injectable rhBMP-2. Thus, injectable rhBMP-2 may be a suitable choice of a bone graft substitute when achieving solid interbody fusion in the lumbosacral junction.

Background: The target volume for post-mastectomy radiation therapy (PMRT) in breast cancer patients with reconstruction has been a subject of debate. This study aimed to assess the radiation dose distribution and treatment outcomes associated with different chest wall (CW) delineation according to ESTRO ACROP guideline for patients underwent implant-based reconstruction. Methods: We conducted a retrospective review of breast cancer patients who underwent mastectomy followed by two-stage implant-based breast reconstruction and adjuvant radiation therapy (RT) between 2007 and 2022. The expanders/implants were positioned retropectorally. The chest wall target volumes were categorized into two groups: the prepectoral group, which excluded the deep lymphatic plexus, and the whole expander group. Results: The study included 26 patients, 15 in prepectoral group and 11 in whole expander group. No significant differences were observed in normal organs exposure between the two groups. There was a trend toward a lower ipsilateral lung mean dose in the prepectoral group (10.2 vs. 11.1 Gy, p=0.06). Both groups exhibited limited instances of reconstruction failure and local recurrence. Conclusions: For patients undergoing two-stage expander-implant retropectoral breast reconstruction and PMRT, our data have provided comparable outcomes and normal organs exposure for those omitting the deep lymphatic plexus.

Extreme atrophy of the maxilla poses still challenging for the clinicians. Some of the techniques used could be complex, risky, expensive, time consuming and should be performed, preferably, only by skilled surgeons. Most the commonly used techniques have been reported to have very high success percentages; however, sometimes complications may occur. In this regard, Premaxillary Device (PD) is a technique that has been devised to render more simple the reconstruction of extremely atrophic maxilla, trying to avoid more complicated and risky surgical procedures. Finite Element Analysis (FEA) allows evaluation of several differen aspects of dental implant biomechanics. Our results showed that the use of PD allows an optimal distribution of the stresses on the basal bone, avoiding tension peaks that could determine bone resorption or, even, implant failure. ANSYS has been used to perform this type of localized finite element analysis; with this type of analysis, it was possible to analyze the peri-crestal area of the plant more precisely and the PD through a more accurate reconstruction of the mesh element, which allowed us to mathematically solve the FEA solution. A most favorable biomechanical behavior has been found for the materials such as titanium alloys and reduce stress levels for bone, implants, screws, and abutments. Moreover, the stress values did not exceed bone strength limits for basal bone and titanium alloy. In conclusion, from a biomechanical point of view, PD could be considered a viable alternative for rehabilitation of severe atrophic maxilla.

The RAINBOW Phase III study established the efficacy of the combination of paclitaxel and ramucirumab, a monoclonal antibody targeting VEGF receptor-2 (VEGF-R2), as second-line therapy. We retrospectively analyzed the data of patients treated with ramucirumab plus paclitaxel at our Institution to evaluate the impact of clinical heterogeneous figures on the efficacy and safety of this combination paclitaxel/ramucirumab in a real- life cohort of patients. After a median follow-up of 10.74 months, the median progression-free survival (PFS) was 5.8 months (95% CI: 3.04 - 5,63). Disease control rate (DCR) was 61% and the median duration of response (DOR) was 5.8 months. Median overall survival (OS) was 8.3 months. A trend toward better outcome was observed in HER2 positive patients. In multivariate analysis, nutritional status (p = 0.0001) and number of metastatic sites (p = 0.0266) resulted significantly related with longer PFS. Our analysis confirmed the efficacy and safety of the combination of ramucirumab with paclitaxel also in the real-life practice and the median PFS is significantly longer than that reported for Western population in previous studies. Subgroup analysis confirms the key-role of nutritional status as prognostic factor and suggests a possible interaction between EGF and angiogenesis pathways that deserves further investigations.