Background: Fiber-reinforced composites (FRCs) have been proposed as an alternative to traditional metal alloys for the realization of frameworks in full-arch implant supported prostheses. The aim of the present in vitro study was to evaluate the deflection under load of seven prostheses endowed with frameworks made of different materials, including different types of fiber reinforced composites (FRCs). Methods: A master cast with four implant analogues in correspondence of the two lateral incisors and the two first molars was used to create full-arch fixed prostheses with the same shape and different materials. Prostheses were made in different materials (framework+veneering material): gold alloy+resin (Au+R), titanium+resin (Ti+R), FRC with multi-directional carbon fibers+resin (ICFRC+R), FRC with unidirectional carbon fibers+composite (UCFRC+C), FRC with glass fibers+resin (GFRC+R), FRC with glass fibers+composite (GFRC+C), resin (R, full-acrylic prosthesis). Flexural tests were conducted using Zwick/Roell Z 0.5 machine and the deflection of the lower surface of the prosthesis was measured in order to obtain load/deflection graphs. Results: Greater rigidity and less deflection were recorded for UCFRC+C, GFRC+C, followed by Ti+R, and Au+R. The greatest deformations were observed for resin alone, ICFRC+R and GFRC+R. The results were slightly different in the incisal region probably due to the greater amount of veneering material in this area. Conclusions: When used to realize full-arch frameworks, Au and Ti allow a predictable mechanical behavior with gradual deformations with increasing load. UCFRC also demonstrated good outcomes and less deflection than ICFRCs when loaded. The GFRC full-arch framework may be a valid alternative, however showed greater deflections. Further studies are needed in order to evaluated how different prosthesis design and material thickness might affect the outcomes.

Background: This study aimed to evaluate survival rate, marginal bone levels, and full arch prosthetic success on short implants when placed in areas of severely resorbed and edentulous mandibles. Methods: This is a systematic review of all randomized controlled trials of at least 10 patients with a control group in which bone augmentations were performed that were published between January 2010 and February 2023. Only 3 relevant studies met the inclusion criteria. Results: It obtained demonstrate that short-term dental implant survival rates ranged from 94.2% to 97.4% with a 5-year follow-up and the prosthetic success rate varied by 62% during the same follow-up. The mean marginal bone level values ​​of the affected short implants ranged from 0.2 mm to 0.6 mm. Conclusions: The data obtained demonstrated that short dental implants positioned with criterion and precision as a full-arch fixed support are a valid therapeutic choice for the medium-long term rehabilitation of severe edentulous mandibular atrophy.

Background - Mandibular flexion (MF) is a complex biomechanical phenomenon, which involves a deformation of the mandible, due mainly to the contraction of the masticatory muscles, and can have numerous clinical effects. The main aim of the current systematic review is to highlight the different factors that can increase MF, to help clinicians, identify patients to whom they should pay more attention. As a secondary outcome, we wanted to analyze the preventive measures and suitable techniques to be adopted to minimize the negative effects of this phenomenon on oral fixed rehabilitations. Methods - The review, which was carried out in accordance with the “Preferred Reporting Items for Systematic reviews and Meta-Analyses” (PRISMA) flowchart, was recorded in the “International Prospective Register of Systematic Reviews” (PROSPERO). As research questions, “Patient/Population, Intervention, Comparison and Outcomes” (PICO) questions were employed. Using the ROBINS-I technique, the risk of bias in non-randomized clinical studies was evaluated. Results - The initial electronic search identified over 1300 potential articles, of which 54 studies were included in this systematic review. Information regarding the relationship between MF and individual factors, mandibular movements, impression-taking and fixed rehabilitations were obtained. Conclusions – The studies included in this systematic review showed that MF is greater during protrusive movements, in the posterior areas of the lower jaw, and in patients with brachial facial type, greater jaw length, small gonial angle and less density, length and bone surface of the symphysis. The biomechanical effects of mandibular flexion on fixed restorations are debated. Prospective clinical and radiological observational studies should be conducted to evaluate the potential short-, medium- and long-term consequences of MF.

Can the type of implant rehabilitation influence peri-implant bone loss in case of full-arch mandibular prosthesis? The purpose of the study was to assess, by orthopantomograms (OPG), bone loss around implants in different types of implant-supported prosthetic rehabilitations and evaluate potential risk factors associated with the number and location of implants that may have an association with bone defect. A radiographic study was conducted on 22317 OPGs in the time range from 2010 to 2024. All OPGs with implant-supported prosthetic mandibular rehabilitations were included in the study. A total of 155 OPGs were evaluated, with peri-implant bone loss identified in 64 (41.3%). Distal implants (furthest from the center) across various positioning patterns were most susceptible to bone loss, with positions 3.6 and 4.6 demonstrating the most frequent occurrences (25 and 26 cases, respectively). χ² test revealed significant associations between both implant positioning pattern (p < 0.001) and number of implants (p < 0.001) with peri-implant bone loss. Also by updating the sample of OPGs, increased susceptibility to bone resorption was found for implants placed distal to the mental foramen compared to mesial ones in full-arch implant-supported fixed prostheses. Prospective clinical studies will then be useful to investigate this finding further.

The effect of the different dental implants positioning region on the stress performance of the implant-supported prosthesis is not yet clear. This study evaluated the dental treatment with six dental implants in three different models and three different occlusal loading conditions, in terms of the biomechanical response of implants, prosthetic screw and maxilla, using three-dimensional finite element analysis. The finite element models were modelled containing external hexagon implants, as well as a Cobalt-Chromium superstructure. Three types of loads were applied: in the area of ​​the central incisors, first premolar and in the second molars. For the finite element simulations, the von-Mises stress peaks in the implant and in the surrounding cortical bone were analyzed. All recorded results reported higher values ​​for the implant-supported prosthesis in group C compared to the groups A and B. The highest stress values, ​​regardless the evaluated model, was in the prosthesis in group C and in screws, the smallest were in group A.

In steel structures, oblique thin steel plates serve as panel zones in structures spanning large spaces (e.g., warehouses and gymnasiums). Considerable research has been conducted on the shear buckling of panels due to seismic loads acting on a structure. Conversely, under snow or wind loads, the panel zone may experience compressive and tensile stresses simultaneously from two directions. Considering the economic preference for thin steel plates, evaluating the elastic critical local buckling stresses in the panel zone under biaxial normal stress may provide essential information to structural engineers. In this study, an elastic buckling analysis based on the energy method is performed to clarify the impact of panel geometry and boundary conditions on the elastic local buckling stresses of oblique panel zones. As confirmed, the buckling stresses derived from the energy method could simulate the local buckling stresses with accuracy comparable to that of finite element analysis, and an engineer-friendly design formula was proposed. Finally, we determined the correlation of the buckling stresses under biaxial stresses and presented a method for evaluating this correlation. Engineers can utilize the provided design equations to more efficiently and accurately calculate buckling loads, facilitating safer and more economical design of structures with oblique plates.

Implant-supported-screw-retained prostheses are really popular. Some of the most frequent complications have been mechanical complications. These include abutment screw loosening or even screw fracture. Using an intermediate abutment can offer several advantages. However, little literature has been found regarding how this affects the mechanical behavior of dental restorations. This study focuses on understanding the mechanical behavior of implant-supported restorations with a transepithelial component compared to those with a direct implant-supported restoration. It was carried out by using the Finite Element Method (FEM) and was experi-mentally validated. The results showed that in the case of transepithelial-supported restoration, the prosthetic screw mounted over the transepithelial component suffers higher stress than the one screwed directly to the implant. After applying a cyclic fatigue load, it is experimentally proven that, in the transepithelial-supported restorations, the fuse changes from being the screw that goes to the implant, to being the upper one. As a conclusion we can say that the use of an intermediate abutment in dental restoration not only provides better protection to the rest of the dental restoration but also allows easier repair in the event of a fracture. This can potentially lead to more efficient procedures and improved patient outcomes.

This study aimed to evaluate the impact of Candida albicans on subgingival biofilm formation on dental implant surfaces. Scanning electron microscopy (SEM) and confocal laser scanning microscopy (CLSM) were used to compare biofilm structure and microbial biomass in the presence and absence of the fungus after periods of 24, 48, and 72 h. Quantitative polymerase chain reaction (qPCR) was used to quantify the number of viable and total micro-organisms for each of the biofilm-forming strains. A general linear model was applied to compare CLSM and qPCR results between control and test conditions. The biofilm developed with C. albicans at 72 h had a higher bacterial biomass, with a significantly higher cell viability (p < 0.05). After both 48 and 72 h of incubation, in the presence of C. albicans, there was a significant increase in counts of Fusobacterium nucleatum and Porphyromonas gingivalis and in the cell viability of Streptococcus oralis, Aggregatibacter actinomycetemcomitans, F. nucleatum, and P. gingivalis. Using a dynamic in vitro multispecies biofilm model, C. albicans exacerbated the development of the biofilm grown on dental implant surfaces, significantly increasing the number and cell viability of periodontal bacteria.

A maxillary totally edentulism was rehabilitated with one-piece implants starting from pre-existing totally removable denture. A 3D digital scan of the removable denture and upper and lower arches was performed. On this basis, a prototype with optimal esthetic and functional outcomes was re-alized and turned into a custom-made radiological stent with markers. The superimposition of STL and DICOM files allowed the virtual planning of one-piece implants ideal position. The stackable templates composed of a fixed component, namely base template, and removable components, were realized. The fixed component, once secured with anchor pins to the bone, was no longer removed. The removable components, screwed to the fixed component, were used to perform the implant surgery and the immediate prosthetic loading. A base template allowed for maintaining a fixed reference during the entire workflow, improving the transition between the digital project, the surgical procedure, and the prosthetic rehabilitation.

The objective of this study was to compare the distribution of stress in the maxillary bone, dental implants, and prosthetic components supporting implant-supported maxillary overdentures with partial palatal coverage, in both splinted and unsplinted designs. Two models of maxillary overdentures were designed using the Exocad Dental CAD program, which included cancellous and cortical bone. The complete denture design and abutments (locator abutments in the unsplinted and Hader bar with Vertix attachments placed distally in the splinted variant) were also designed. The denture material was PEEK (Polyetheretherketone), and the method used to analyze patient-specific 3D X-ray scans was 3D QCT/FEA (Three-dimensional Quantitative Computed Tomography-Based Finite Element Analysis). Loading was divided into three load cases: frontal region (both incisors of the denture) and distal region (both molars and first premolar of the denture). The forces applied were 150 N with an oblique component with a buccal inclination of 35° in the frontal region, and 600 N with a buccal inclination of 5° (molars) or solely vertical (premolar) in the distal region. The model with locator abutments showed higher stresses in all load cases in both analyzed implant variants and in the maxilla. The differences in stress distribution between the splinted and unsplinted variants were more significant in the distal region. According to the results of the present study, the amount of stress in bone tissue and dental implant parts was smaller in the splinted, bar-retained variant. The findings of this study can be useful in selecting the appropriate prosthetic design for implant-supported maxillary overdentures with partial palatal coverage.

Immediate load of full-arch rehabilitations over implants, specially over 4 implants are very well documented in the literature. More recently, the use of computed surgical guides to help the planning and the execution of these treatments, in many situations without the need of raising a flap, and diminishing the appearance of hematomas, bleeding and with less trauma to the patient has gained preference among implantologists. The objective of this case report is to show a clinical case of an immediate load full-arch fixed rehabilitation over 4 implants produced by 3D printing manufacturing technology, and placed with a computed surgical guide, in the same appointment, and the 24 months follow-up. The patient returned after 3 months to replace the immediate temporary fixed prosthesis for a new one, with metallic bar, better teeth and more delicate. Soft and hard tissue around the implants seemed to be stable, without signs of inflammation, either on the 3 or the 24 months follow-up. 3D printing of implants by direct metal laser sintering is a technology that seems to be promising for oral implantology, with solid studies showing reliable results, as seen in this single case. More clinical studies are necessary to testify its efficacy.

Background: Patients with thromboembolic disease, prosthetic valves, or coagulation issues are commonly prescribed anticoagulants and antiplatelets. Although common professional oral hygiene might not represent a health concern for these patients, anticoagulant and antiplatelet medication might constitute a challenge for dentists and dental hygienists since possible prolonged bleeding might interfere with dental procedures. The aim of the present study was to investigate the bleeding time of different anticoagulants and antiplatelets during a professional hygiene session adapting the Ivy test to the oral environment; Methods: 93 consecutive patients undergoing professional oral hygiene were recruited. Debridement during oral hygiene was performed using ultrasonic mechanical instrumentation, and bleeding sites were assessed and treated with gentle pressure using sterile gauzes. The time for bleeding cessation was recorded. Patients were categorized into six groups based on their drug intake, Control: no anticoagulants or antiplatelets DTI: direct thrombin inhibitors (dabigatran) AntiXa: directa factor Xa inhibitors (endoxaban, apixaban, rivaroxaban) VKA: vitamin K antagonists (warfarin, acenocoumarol) SAPT: single anti-platelet therapy (acetylsalicylic acid or clopidogrel) DAPT: dual anti-platelet therapy (acetylsalicylic acid and clopidogrel). Bleeding time was measured in seconds and mean values were assessed among the different groups. Differences between groups were investigated with Kruskal-Wallis test followed by Dunn’s post-hoc correction for multiple comparisons or two-way ANOVA followed by Dunnett post-hoc; Results: Control patients presented the lowest bleeding time 50 sec, followed by AntiXa (98), SAPT (105), DTI (120), DAPT (190) and VKA (203). A statistically significant difference was present among control and DTI (p=0.004), VKA (p<0.001), DAPT (p<0.001). Conclusions: Based on the present outcomes, an increased risk of prolonged bleeding emerged in patients taking VKA and DAPT. However, bleeding did not interfere with the oral hygiene ses-sion The optimal period for dental treatment of these patients should be 2-3 hours before the next dose, without the need to temporarily suspend the medication.

Aseptic implant loosening after total joint replacement is partially influenced by material-specific factors when cobalt-chromium alloys are used, including osteolysis induced by wear- and corrosion products, and stress shielding. Here, we aim to characterize a hybrid material consisting of alumina-toughened zirconia ceramics (ATZ) and additively manufactured Ti-35Nb-6Ta (TiNbTa), joined by a glass solder. The structure of the joint, static and fatigue shear strength, the influence of accelerated aging, and the cytotoxicity using an elution assay with human osteoblasts is characterized. Furthermore, the biomechanical properties of functional demonstrators of a femoral component for total knee replacements are evaluated. TiNbTa-ATZ specimens showed a homogenous joint with statistical distributed micro-pores and a slight accumulation of Al-rich compounds at the glass solder-TiNbTa interface. The static shear strength was 26.4 ± 4.2 MPa (Ti-ATZ reference: 38.2 ± 14.4 MPa, p = 0.117), all specimens survived 107 cycles of shear loading to 10 MPa, and aging did not reduce the strength. TiNbTa-ATZ did not impair the proliferation and metabolic activity of human osteoblasts. Functional demonstrators of TiNbTa-ATZ provided a maximum bearable extension-flexion moment of 40.7 ± 2.2 Nm. Biomechanical and biological properties of TiNbTa-ATZ demonstrate potential application for endoprosthetic implants.

The aim of this study was to compare the screw removal torque of mini conical prosthetic components and straight trunnion of indexed morse taper implants, after mechanical cycling. The sample consisted of 40 implants and 20 mini-conical prosthetic components (MC group) and 20 straight trunnion components (ST group). Each group consisted of 10 specimens, with 2 implants in each, and cobalt-chromium metallic crowns were screwed into each sample. The components of the MC group received a torque of 20 N.cm with a digital torque wrench and after 10 minutes were retightened with the same value as the initial torque. The components of the ST group received a torque of 30 N.cm, with a digital torque wrench and after 10 minutes, they were retightened with the same value. The screws of the respective crowns of the two groups received a torque of 10 N.cm and after 10 minutes were retightened with the same value. Each group was subjected to the fatigue test in a mechanical cycler at 2.000.000 cycles, with a load of 250 N and frequency of 4 Hz. At the end of the fatigue test, the loosening torque of each screw of the specimens was measured through a digital torque wrench. The data were analyzed by two-way ANOVA and Tukey test. In both groups, there were loss of torque. The results showed no statistic difference between MC and ST groups.

This study aims to spatially analyze the distribution characteristics of vacant homes in Asan-si, Chungcheongnam-do, and understand the differences in factors causing vacant homes by type. We use a variety of statistical methods to examine these factors and identify key influencing factors such as the number of vacant stores, changes in overall population, land use complexity, and physical characteristics of land and buildings. The findings reveal that the factors contributing to the occurrence of vacant homes vary significantly by region and property type, highlighting the need for region-specific policies. For instance, in old town areas, small lot ratios and land use complexity are significant, while in rural village, the average number of floors and land use complexity play a major role. This study underscores the diversity of factors influencing vacant homes, suggesting that policies should be tailored to the unique characteristics of different regions to effectively address this issue.

Background/Objectives: Dental implants have become a cornerstone of restorative dentistry, providing a long-lasting method for tooth replacement. The level of osseointegration has a big impact on the biomechanical stability at the bone-implant contact (BIC), which determines how long these implants will work. However, the exact consequences of changing osseointegration levels on different implant designs, especially in bones with variable densities, are not well known. Three short dental implants were tested in this study: BioMet 3iT3, Straumann® Standard Plus Short Regular Neck (SPS-RN), and Straumann® Standard Plus Short-Wide Neck (SPS-WN). 3D finite element analysis (FEA) was used to look at how well they worked biomechanically. This paper tests the implants at four stages of osseointegration: 25%, 50%, 75%, and 100% in both high-density (Bone Type III) and low-density (Bone Type IV) cancellous bone. It also created and examined realistic CAD models under static occlusal loading conditions to assess stress distribution and major strains at the bone-implant contact.; Results: The study discovered that as osteointegration increases, von Mises stress and principal strains go down significantly for all implant types. The SPS-WN implant had the lowest strain values, especially for bone with low density. These reductions demonstrate increased mechanical stability as the bone-implant inter-face becomes more capable of dispersing mechanical stresses, minimizing the potential for localized deformation and bone resorption.; Conclusions: The results highlight the importance of achieving optimum osseointegration to reduce mechanical stress and increase the lifespan of dental implants. The SPS-WN type implant performed better in biomechanical tests than the others, especially when bone conditions were not ideal. This makes it a great choice for clinical applications that need long-term implant success.

Introduction Cochlear implants are a modern approach for the treatment of multiple cases of profound sensorineural hearing loss. Factors such as the ethiology of hearing loss and the potential for achieving good postoperative outcomes are considered in cochlear implantation. Additionally, surgical strategies, protocols, the experience of the surgeon and audiologist, and the presence of postoperative issues and risks that may require revision surgery should also be taken into account. The surgeon specialized in cochlear implantation must inform the patient and his relatives not only about the surgical technique but also about possible complications. The literature shows different rates of complications evaluated both in adults and in children. An evaluation of adverse events in order to prevent complications can be made if the definition of medical complications and mistakes is strictly approached based on the CLAVIEN-DINDO classification system. The rate of complications can be compared with existing literature. Studies demonstrate the need for preoperative vaccination for pneumococcus, which can prevent complications, especially in patients with inner ear malformations who present an increased postoperative risk Relevant Sections This review is structured around the collection of specialized literature from PubMed, organized into subchapters related to intraoperative complications such as Gusher syndrome, foreign body reaction, endocochlear inflammation phenomena, issues related to electrode positioning and associated complications, vestibular phenomena related to cochlear implantation, as well as late complications related to the surgical wound and cochlear implant extrusion. The important sections in this review are: Inner Ear Malformations and Gusher Syndrome: Intraoperative Complication Risks, Electrode Insertion and Positioning Issues, Intracochlear Inflammation, Foreign Body Reaction, and Intracochlear Fibrosis: Phenomena That Can Occur with Cochlear Implantation, Vestibular Disorders, Tardive Postoperative Complications: Wound Injuries and Cochlear Implant Extrusion and Otitis Media and Cholesteatoma as Complications of Cochlear Implantation Conclusions: Postoperative complications, although considered quite rare. The surgical limits and long-term evolution of cochlear implants cannot be concretely established, despite the fact that this intervention is considered safe in the medium and long term. Future directions Given that cochlear implants represent the most modern surgical technique for auditory rehabilitation in adults and children, with massive implications for quality of life, there is a tendency to extend surgical indications in the future, and especially to inform doctors in related specialties about the benefits of this medical device. Surgeons must be knowledgeable about cochlear implantation methods, as well as the methods for managing complications that can arise immediately postoperatively, as well as in the medium and long term.

This study examines the effect of a hyaluronic acid (HyAc) containing tricalcium phosphate putty scaffold material (TCP-P) and of a particulate tricalcium phosphate (TCP-G) graft on bone formation, volume stability and osteogenic marker expression in biopsies sampled 6 months after bilateral sinus floor augmentation (SFA) in 7 patients applying a split-mouth design. Biopsies were processed for immunohistochemical analysis of resin embedded sections. Sections were stained for collagen type I (Col I), alkaline phosphatase (ALP), osteocalcin (OC) and bone sialoprotein (BSP). Furthermore, the bone area and particle area fraction were determined histomorphometrically. Cone-beam CT data recorded after SFA and 6 month later were used for calculating the graft volume at these two time points. TCP-P displayed more advantageous surgical handling properties and a significantly greater bone area fraction and smaller particle area fraction. This was accompanied by significantly greater expression of Col I and BSP and in osteoblasts and osteoid and a less pronounced reduction in grafting volume with TCP-P. SFA using both types of materials resulted in formation of sufficient bone volume for facilitating stable dental implant placement with all dental implants having been in function without any complications for 6 years. Since TCP-P displayed superior surgical handling properties and greater bone formation than TCP-G, without the Hyac hydrogel matrix having any adverse effect on bone formation or graft volume stability, TCP-P can be regarded as excellent grafting material for SFA in a clinical setting.

Resonance inductive coupling is widely used for wireless power transfer (WPT) in medical applications. In this paper, we analyze the LCL-compensated WPT structure and propose a novel constant voltage transmission system based on gain estimation, without any extra feedback from the receiver. The system is capable for implant neural stimulation where the load impedance and the coupling coefficient are both variable. Compared to existing methods for constant voltage transmission, our approach offers advantages in compact size and the compatibility with the industrial, scientific and medical (ISM) band. We validate the load-independent resonant characteristic and the feasibility of constant voltage transmission using an experimental prototype working at 6.78MHz. Finally, we discuss the structure of the implant stimulator and methods of applying the proposed WPT system.

We use binary string to represent a natural number and show the composite procedure of odd-number and even-number functions, thus we propose full binary directed tree to represent the set of natural numbers and give another partition the natural number set to three sets: pure odd, pure even and mixed number. For the Collatz conjecture we make use of the parity of a natural number to analyse the sequence of iteration (or composite) of Collatz function and reduced Collatz function analog to the inverse function. We give tabular and binary strings to the algebra expression to state the sequence of Collatz, this is the key topic to proof the conjecture: the discrete powers of 2 can be changed to ultimately continuous powers of 2, finally get to pure even number and to the smallest number 1. The sequence created by the infinite iterations of the Collatz function becomes the ultimately periodic sequence if any natural number is the beginning value, proving the conjecture that has been held for 87 years.

Keywords: olfactory rehabilitation; chronic pain; fMRI;

(1) Background : When placing implants in the maxillary posterior region with insufficient alveolar bone, a maxillary sinus elevation is necessary. Autogenous bone, though biologically ideal, poses risks and discomfort due to donor site harvesting. Block-type autogenous tooth bone graft material, made from the patient’s own extracted tooth, offers similar biological stability without these drawbacks; (2) Methods : This study observed the progress of 19 implant patients who were treated with maxillary sinus elevation procedures using block-type autogenous tooth bone graft material at the Daegu Catholic University Medical Center. Extracted teeth were processed into demineralized tooth block bone. After elevating the sinus membrane, implants and the tooth bone graft material were placed in the space, and the bony window was repositioned. Postoperative evaluations through clinical observation and radiographic imaging assessed sinus membrane elevation, alveolar bone height increase, and implant osseointegration; (3) Results : Results showed proportional increases in alveolar bone height to the graft material size, with long-term stability. No postoperative complications occurred, even with sinus membrane perforation, and implants remained stable; (4) Conclusions : The study concludes that maxillary sinus lifts using block-type autogenous tooth bone graft material provide excellent bone induction and biocompatibility, making it a highly beneficial method for both dentists and patients.

Conditional heteroskedastic financial time series are commonly modelled by (G)ARCH processes. ARCH(1) and GARCH were recently established in C[0,1] and L^2[0,1]. This article provides sufficient conditions for the existence of strictly stationary solutions, weak dependence and finite moments of (G)ARCH processes for any order in C[0,1] and L^p[0,1]. It deduces explicit asymptotic upper bounds of estimation errors for the shift term, the complete (G)ARCH operators and the projections of ARCH operators on finite-dimensional subspaces. The operator estimaton is based on Yule-Walker equations, and estimating the GARCH operators also involves a result estimating operators in invertible linear processes being valid beyond the scope of (G)ARCH. Moreover, our results regarding (G)ARCH can be transferred to functional AR(MA).

A comprehensive kinetic model of the Fischer-Tropsch synthesis (FTS) is developed in a fixed bed reactor under operating conditions (temperature, 230–235°C, pressure, 20–25 bar, gas hourly space velocity, 4000–5000 cm³(STP)/h/g_catalyst ,H₂/CO feed molar ratio, 2.1) over a Co based catalyst. Reaction rate equations based on Eley-Rideal (ER) type model for initiation step and Langmuir-Hinshelwood-Hougen-Watson (LHHW) type model for propagation and termination steps of the FTS reactions have been considered and the readsorption of olefins were taken into account. The model that was reported in the literature was modified in order to explain many significant deviations from the ASF distribution. Optimum parameters have been obtained by Genetic Algorithms (GA). The calculated activation energies to produce n-paraffins and 1-olefins were in the range of 82.24 to 90.68 kJ/mol and 100.66 to 105.24 kJ/mol, respectively. The hydrocarbon distribution in FTS reactions was satisfactorily predicted particularly for paraffins.

Some peptide-based drugs including oxytocin, vasopressin, ziconotide, pramlintide, nesiritide, and octreotide, contain one intramolecular disulfide bonds. A novel and reusable monodispersed silica nanosphere-supported Pt(IV) complex (SiO2@TPEA@Pt(IV)) was synthesized via a four-step procedure and used for formation of intramolecular disulfide bonds in peptides. TEM and chemical mapping results for the Pt(II) intermediates and for SiO2@TPEA@Pt(IV) show that the silica nanospheres possess a monodisperse spherical structure and contain uniformly distributed Si, O, C, N, Cl, and Pt. The valence state of Pt on the silica nanospheres was characterized by XPS. The Pt(IV) loaded on SiO2@TPEA@Pt(IV) was 0.15 mmol/g, as determined by UV-vis spectrometry. Formation of intramolecular disulfides in six dithiol-containing peptides of variable lengths by use of SiO2@TPEA@Pt(IV) was investigated and the relative oxidation yields were determined by HPLC. In addition, peptide 1 (Ac-CPFC-NH2) was utilized to study the reusability of SiO2@TPEA@Pt(IV). No significant decrease in the relative oxidation yield was observed after ten reaction cycles. Moreover, the structure of SiO2@TPEA@Pt(IV) after being used ten cycles was determined to be similar to its initial one, demonstrating the cycling stability of the complex.

The first Network Arch Bridge (NAB) was opened to traffic 60 years ago and since then the idea spread around the world. It is a type of a tied arch bridge that combines the benefits of tied arch bridges and trusses in a single system, thus it has a very good stiffness even in the case of extremely slender structures. In a Network Arch the hangers are inclined and some of them intersect each other at least twice. The core of a NAB is the hanger arrangement that minimizes the bending moment in the arch to very small values, leading thus to compression in the arch. This paper reviews the Network Arch idea devised by prof. Tveit and extended by researchers and engineers worldwide. A comprehensive review of the literature about the Network Arch is provided and the situation of NABs around the world from the standpoint of location, span, structural system used for the cross-section, bridge type (road, railway, combined or pedestrian) and opening year is discussed.

Peri-implant infective diseases seem to be the most common cause for the late dental implant failure. Therefore, peri-implant microbiota has been intensively studied in modern implantology. Many studies showed a presence of extremely varied microflora in cases of peri-implant infective diseases. The main scope of this observational single-blind study was to analyze the presence of some microbial species in a group of patients with clinical signs of peri-implant mucositis compared to two other groups (patients treated with dental implants but without any clinical signs of peri-implant inflammation and patients treated with no dental implants). The identification of microorganisms was followed by an antibiogram in order to find their sensitivity to various antibiotics. The results showed a microbiota not necessarily specific for each situation (peri-implant infective diseases, healthy tissues around dental implants and healthy natural teeth and gums) with species like Candida albicans, Neisseria mucosa, Prevotella, Staphylococcus aureus, Streptococcus and others. Peri-implant infective diseases presented more bacterial species than other conditions.

In this paper, we present a full coverage path planning (CPP) algorithm for the marine surveys conducted in the convex polygon shaped search area. The survey is supposed to carry out by torpedo-type AUVs (autonomous underwater vehicles). Due to their nonholonomic mechanical characteristics, these vehicles have nonzero minimum turning radius. For any given polygon shaped search area, it can always be partitioned into one or more convex polygons. With this in mind, this paper proposes a novel search algorithm called CbSPSA (Calculation based Shortest Path Search Algorithm) for full coverage of any given convex polygon shaped search area. By aligning the search inter-tracks alongside the edge with the minimum height, we can guarantee the minimum number of the vehicle’s turns. In addition, the proposed method can guarantee the planned path is strictly located inside the polygon area without overlapped or crossed path lines, and also has the total path length as short as possible. Considering the vehicle’s nonzero minimum turning radius, we also propose a sort of smoothing algorithm to smooth the waypoint path searched by CbSPSA so as for the vehicle to exactly follow it. The smoothed path is also guaranteed to be strictly located inside the polygon. Numerical simulation analyses are also carried out to verify the effectiveness of the proposed schemes.

This paper investigates the periodic and quasi-periodic orbits in the symmetric collinear four-body problem through a variational approach. In Section 3, we analyze the conditions under which homographic solutions minimize the action functional. We demonstrate that these solutions for four equal masses arranged in a linear configuration are indeed the minimizers of the action functional and compute the minimum value of the action functional for these solutions. Additionally, we employ numerical experiments using Poincaré sections to explore the existence and stability of periodic and quasi-periodic solutions within this dynamical system. Our results provide a deeper understanding of the variational principles in celestial mechanics and reveal complex dynamical behaviors that are crucial for further studies in multi-body problems. The findings have significant implications for theoretical research and practical applications in astrodynamics and space mission planning.

The human mandible's cancellous bone, which is characterized by its unique porosity and directional sensitivity to external forces, is crucial for sustaining biting stress. Traditional CAD models fail to fully represent bone's anisotropic structure and thus depend on simple isotropic assumptions. For our research, we use the latest versions of nTopology and Creo Parametric software to make biomimetic Voronoi lattice models that accurately reflect the complex geometry and mechanical properties of trabecular bone. The porosity of human cancellous bone is accurately modeled in this work using biomimetic Voronoi lattice models. The porosities range from 70% to 95%, which can be achieved by changing the pore sizes to 1.0 mm, 1.5 mm, 2.0 mm, and 2.5 mm. Finite element analysis (FEA) was used to examine the displacements, stresses, and strains acting on dental implants with a buttress thread, abutment, retaining screw, and biting load surface. The results show that the Voronoi model accurately depicts the complex anatomy of the trabecular bone in the human jaw, compared to standard solid block models. The ideal pore size for biomimetic Voronoi lattice trabecular bone models is 2 mm, taking into account both the von Mises stress distribution over the dental implant, screw retention, cortical bone, cancellous bone, and micromotions. This pore size displayed balanced performance by successfully matching natural bone's mechanical characteristics. Advanced finite element analysis (FEA) improves biomechanical understanding of how bones and implants interact by creating more accurate models of biological problems and dynamic loading situations. This makes biomechanical engineering better.

Dynamic optical structural color is always desired in various display applications and usually involves active materials. Full-color generation, especially bi-directional full-color generation in both reflective and transmissive modes, without any active materials included has been rarely investigated. Herein, we demonstrate a scheme of bi-directional full-color generation based on a plasmonic metasurface modulated by rotation of the polarization angle of the incident light without varying the geometry and the optical properties of the materials and the environment where the metasurface resides. The metasurface unit cell consists of plasmonic modules aligning in three directions and is patterned in a square array. The metasurface structural color device generates full colors in both reflection and transmission. Based on the proposed polarization-dependent structural color, information encoding of three multiplexed animal images and quick-responsive (QR) codes is demonstrated to verify the efficient information encoding and decoding of the proposed scheme. The animals can be seen under different polarization incidence and the QR codes can be successfully decoded by the polarization rotation in transmission. The proposed bi-directional full-color generation metasurface has great potential in applications such as kaleidoscope generation, anti-counterfeiting, dynamic color display, and optical information encoding.

The Geopyörä breakage test uses two counter-rotating wheels to nip and crush rock specimens with a tightly controlled gap between rollers. The force applied and energy consumed during breakage are measured with instrumentation. In contrast to drop weigh test (DWT) methods, the breakage energy is a response to the rock compressive strength and degree of compression, not a controlled test input, such as the kinetic input energy of a falling weight. This paper presents the detailed measures conducted to evaluate the accuracy and precision of energy measurements across various ore types using the Geopyörä device. While force measurement was assessed just for its precision. The outputs are compared directly to the DWT measures of fragmentation at the same energy and fitted A and b parameters. The test reproducibility was evaluated using a Round-Robin methodology, testing several samples in multiple laboratories. The results confirmed that the new test has sufficient accuracy to match DWT results and excellent precision to assure reproducibility.

Background and Objectives: This study aimed to evaluate the histological and biochemical ef-fects of capsaicin on implant osseointegration and oxidative stress. Materials and Methods: Male Wistar albino rats weighing between 250 and 300 grams were used in this study. Twenty-four rats were randomly divided into three equal groups: implant + control (n= 8), implant + capsai-cin-1 (n= 8), and implant + capsaicin-2 (n= 8). 2.5 mm diameter and 4 mm length titanium im-plants were surgically integrated into the corticocancellous bone parts of the femurs. In the treatment groups, rats were injected intraperitoneally with 25 mg/kg (implant + capsaicin-1) and 50 mg/kg (implant + capsaicin-2) of capsaicin. No additional applications were made in the con-trol group. Three rats in totally were died during and after the experiment, as a result of the an-alyzes performed on 21 animals. Results: The highest total antioxidant status value was found in capsaicin dose 2, according to the analysis. The control group had the highest total oxidant status and oxidative stress index values, while group 2 of capsaicin had the lowest. After analysis, we found that there was no observed positive effect on osteointegration in this study (p> 0.05), alt-hough the bone implant connection was higher in the groups treated with capsaicin. Conclusi-ons: A positive effect on osteointegration was not observed in this study. This may be due to os-teaclast activation. However it was found that it has a positive effect on oxidative stress. Osteo-clast activation may be the cause of this phenomenon. Capsaicin was found to have a positive effect on oxidative stress (p

Emerging data processing techniques brought back into attention the HF range communication as an interesting alternative to third-party solutions for IoT applications, such as data transmission in distributed energy production facilities. The physical size of HF antennas, often comparable to the surrounding objects, require in-situ radiation measurements. Drone-borne measuring systems are already known as a flexible solution, but mostly restricted to higher frequency ranges. In this work, we propose to use an electrically small, folded dipole as a probe for drone-borne measurements on HF antennas. We also propose a calibration approach for the effects related to the near-field zone, and to the drone body proximity. The impact of ground reflection is also investigated. We show that despite its low, realized gain figure such a probe can provide stable results for near-field measurements, even at low input power levels.

A well known technique to enhance the signal to noise ratio (SNR) of repetitive signals is to average them. The coherent parts of the signal add up constructively while the incoherent parts are averaged out. The prerequisite is that the signals are acquired under conditions of high repeatability, i.e.\ the signals must be sufficiently similar. In the present technical note we describe an efficient method for maintaining signal similarity by ensuring spatial and temporal proximity of laser waveform signals obtained by a sensor operated from an airborne platform. The method makes use of a few auxiliary parameters such as laser pulse repetition rate, mirror rotation rate, platform altitude, and flight speed. The method can be extended to be operated in real time.

Environmentally friendly and low-cost sensors are needed for the next generation disposable electronics applications. Given its low-cost, availability and biodegradability, paper-based devices are a very promising. Here we demonstrate the fabrication of a tungsten disulphide (WS2) strain sensor on standard copy paper. The WS2 is deposited through direct abrasion of WS2 powder against the paper surface making the fabrication of the device low-tech and cost effective. The fabricated strain gauge devices present gauge factors up to ~70 for strains in the ± 0.5 % range. These values are ~ 9 times larger than that obtained on devices with the same geometry but using a graphite film instead a WS2 as a sensitive material. We demonstrate the potential of these WS2-on-paper strain gauges by integrating them directly on a paper cantilever to sense mass and forces. We show how this very simple device can detect sub-milligram masses. Moreover, we also demonstrate the capability of transducing motion in mechanical resonators by gluing a WS2-on-paper strain gauge on their surface.

Atlas Posterior Arch Deficiency (APAD) is a rare anatomical variation of the atlas vertebra that can be detected using cone-beam computed tomography (CBCT). This study aims to evaluate the prevalence, classification, and clinical implications of APAD in an Italian cohort.

Transcatheter aortic valve implantation (TAVI) has grown exponentially within the cardiology and cardiac surgical spheres. It has now become a routine approach for treating aortic stenosis. Several uncertainties have been raised about TAVI in comparison to conventional surgical aortic valve replacement (SAVR). The primary concerns are with regards to the longevity of the valves. Several factors have been identified that may predict poor outcomes following TAVI. These include the lesser-used finite element analysis (FEA) to quantify the properties of calcifications that affect TAVI valves. This can also be used in conjunction with other integrated software to ascertain the functionality of these valves. Other imaging modalities are now widely available such as Multi-detector row computed tomography(MDCT) which can accurately size the aortic valve annulus.. This may help reduce the incidence of paravalvular leaks and regurgitation which may necessitate further intervention. Structural valve degeneration (SVD) remains a key factor with varying results from current studies. The true incidence of SVD in TAVI compared to SAVR remains unclear with the lack of long term data. It is now widely accepted that both are part of the armamentarium and are not mutually exclusive. Decision-making for the appropriate intervention should be made via shared decision-making involving the heart team.

The aim of this study was to evaluate the use of a flexible synthetic polymer bone graft to provide implant stability in the absence of implant stability during implant placement in a dense cortical bone model. Sockets were prepared on polyurethane blocks according to the standard implant socket drilling protocol in the control group, both oversizing and deepening in group 2, and oversizing only in group 3. In groups 2 and 3, flexible synthetic polymer bone grafts were placed in the sockets prior to implant placement. The implants were placed at bone level in all groups. The highest torque value obtained was recorded as the insertion torque. 75 implant sites in 3 groups were included in the study. The torque values of the implants in the control group were significantly higher than those of the implants with the oversized and deepened sockets and the oversized-only sockets (p<0.05; p<0.01).The torque values of the implants with the oversized and deepened sockets were significantly higher than those of the implants with the oversized-only sockets (p<0.01). In this study, flexible synthetic polymer bone graft was shown to be effective in achieving implant stability in the management of implants with loss of primary stability.

As medical care aiming to maintain the quality of life for elderly patients is increases, implant treatment for elderly patients is increasing worldwide. Therefore, we aimed to investigate implant stability and the reliability of different measuring devices according to implant placement site and duration in patients aged over 65 years. The study evaluated 60 implants in 60 patients aged ≥ 65 years. The implant placement sites were divided into six evenly distributed sections (n=10) i.e., maxillary right- posterior, A; maxillary anterior, B; maxillary left-posterior, C; mandibular right-posterior, D; mandibular anterior, E; mandibular left-posterior, F. Participants visited the hospital seven times: preoperatively, 1V; implant surgery, 2V; stitch removal, 3V; 1-month follow-up, 4V; 2-months follow-up, 5V; before final-restoration delivery, 6V; and after final-restoration delivery, 7V. The implant stability was evaluated with the Osstell Mentor (ISQ), Periotest M (PTV), and Anycheck (IST). The mean values of ISQ, PTV, and IST were analyzed (α=.05). ISQ, PTV, and IST results of 5V and 6V were significantly higher than those of 2V (P<.05). The lowest ISQ results occurred in E location at 5V and 6V (P<.05). In all mandibular locations, IST results of 7V were significantly higher than those of 2V, 3V, 4V, and 5V (P<.05). ISQ results were negatively correlated with PTV and positively correlated with IST, and PTV was negatively correlated with IST. By considering various factors that affect implant stability, the appropriate implant load application time was determined. This could help increase the implant success rate in elderly patients. And as a diagnostic device for implant stability for evaluation of osseointegration in elderly patients, Anycheck was also able to prove its relative reliability compared to Osstell ISQ Mentor and Periotest M.

Although the connection of implant abutments to implant analogs and implant bodies has been evaluated separately, comparative evaluation of connections to implant analogs and implant bodies has not been evaluated. The objective of this study was to identify whether torque applied during laboratory manufacturing and during restoration cementation affects the compatibility between the implant body-abutment and the implant analog-abutment, as well as to spot any structural differences. Three different implant system with internal conical connection (Bioinfinity, Dant, and Dentist) were used. For each group, straight abutments (n=20) were tightened to implant analogs (n=10) and implant bodies (n=10) with hand tightening and using torque wrench device. The fitting of componenets were evaluated for each group using linear and volumetric micro-CT analysis. For linear analysis, when the mean differences (difference between measurements of the linear distance of abutments during hand tightening and applying torque) values between implant analog and implant body were compared within groups, There was no statistically significant difference observed in all groups (p&gt; 0.05). Throughout the fabrication and clinical phases, it is recommended to tighten the abutments on the analogs with a torque wrench instrument to minimize the risk of prosthetic incompatibility.

High-throughput screening technologies continues to produce large amounts of multiomics data from different populations and cell types for various diseases, such as cancer. However, analysis of such data encounters difficulties due to cancer heterogeneity, further exacerbated by human biological complexity and genomic variability. There is a need to redefine the drug discovery development pipeline, bringing an Artificial Intelligence (AI)-powered informational view that integrates relevant biological information and explores new ways to develop effective anticancer approaches. Here, we show SynPred, an interdisciplinary approach that leverages specifically designed ensembles of AI-algorithms, links omics and biophysical traits to predict synergistic anticancer drug synergy. SynPred exhibits state-of-the-art performance metrics: accuracy – 0.85, precision – 0.77, recall – 0.75, AUROC – 0.82, and F1-score - 0.76 in an independent test set. Moreover, data interpretability was achieved by deploying the most current and robust feature importance approaches. A simple web-based application available online at http://www.moreiralab.com/resources/synpred/ was constructed to predict synergistic anticancer drug combinations requiring only the upload of the two drug SMILES to be tested, allowing easy access by non-expert researchers.

The aim of this study was to evaluate the effect of two different insertion speeds at 8 different insertion torque values ranging from 25-60 during implantation in a dense polyurethane D1 bone model on the placement status and removal torque of dental implants. In this study, 50 pcf single layer polyurethane plates were used. In the study, a total of 320 implant sockets were divided into 2 groups as Group 1 (30 rpm) and Group 2 (50 rpm) in terms of insertion speed. Group 1 and Group 2 were divided into 8 subgroups as 25, 30, 35, 40, 45, 50, 55 and 60 torques. There were 20 implant sockets in each subgroup. During the implantations, implant placement status and removal torque values were assessed. There was a statistically significant difference between the 30 and 50 RPM groups in terms of overall implant placement status (p&lt;0.01). It was found that the removal torque values at 50 RPM were statistically significantly higher than those at 30 RPM (p&lt;0.01). This study showed that in dense D1 bone, the minimum parameters at which all implants could be placed at bone level were 50 torque at 30 rpm and 40 torque at 50 rpm.

Background: Cochlear implantation is an efficient treatment for postlingually deafened adults who do not benefit sufficiently from acoustic amplification. Implantation is indicated when it can be foreseen that speech recognition with a cochlear implant (CI) is superior to that with a hearing aid. Especially for subjects with residual speech recognition it is desirable to predict CI outcome on the basis of preoperative audiological tests. Purpose: The purpose of the study was to extend and to refine a previously developed model for CI outcome prediction for subjects with preoperative word recognition to include subjects with no residual hearing by incorporat-ing additional results of routine examinations. Results: By introducing the duration of unaided hearing loss (DuHL) the median absolute error (MAE) of the prediction was reduced. While for subjects with preoperative speech recognition the model modification did not change the MAE, for subjects with no residual speech recognition before surgery, the MAE decreased from 23.7% with the previous model to 17.2% with the extended model. Conclusions: Prediction of word recognition with CI is possible within clinically relevant limits. Outcome prediction is particu-larly important for preoperative counselling and in CI aftercare, to support systematic monitor-ing of CI fitting.

A multiscale model that enables quantitative understanding and prediction of the size effect on scattering properties of micro- and nanostructures is crucial for the design of LED surface textures optimized for high light extraction efficiency (LEE). In this paper, a hybrid process for combining full-wave finite-difference time-domain simulation and a ray-tracing technique based on a bidirectional scattering distribution function model is proposed. We apply this method to study the influence of different pattern sizes of a patterned sapphire substrate on GaN-based LED light extraction from the microscale to the nanoscale. The results show that near-wavelength–scaled patterns with strong diffraction are not expected to enhance LEE. By contrast, microscaled patterns with optical diffusion behavior have the highest LEE at a specific aspect ratio, and subwavelength-scaled patterns that have antireflection properties show marked enhancement of LEE for a wide range of aspect ratios.

(1) Background: This study aimed to compare the effect of polyetheretherketone (PEEK) and titanium abutments on implant prosthetic systems and supporting bone using three-dimensional finite element analysis (FEA); (2) Methods: A three-dimensional finite element analysis was conducted using CATIA and Abaqus software to model mandibular first molar implant systems with titanium and PEEK abutments. Under external loading conditions, finite element analysis was conducted for the stresses in implant components and surrounding bones of each group; (3) Results: The implant fixture of the PEEK model exhibited the highest von Mises stress (VMS). The lowest VMS was observed in the abutment screw of the titanium model. Both implant systems demonstrated similar stress distribution and magnitudes in cortical and cancellous bones; (4) Conclusion: PEEK abutments show similar stress distribution in surrounding bone compared to titanium. However, PEEK absorbs the stresses within the implant system and exhibits the highest VMS values due to its low mechanical and physical properties. Therefore, PEEK abutments need improved mechanical properties for better clinical application.

In this study, the team employed full-scale crash tests to investigate the impact of post-densification technology on the safety performance of separated central median W-beam barriers under low compaction conditions. By precisely simulating the design and construction environment of the central median, the study comprehensively evaluated the barrier's containment, redirection, buffering, and anti-intrusion performances, as well as the deformation of both the barrier and vehicles under various collision scenarios. The results indicate that under low compaction soil conditions, the A-level separated central median barriers reinforced with post-densification technology effectively meet the specified protection requirements. By comparing the influence of soil strength variations on barrier performance under simulated rainfall conditions, it was confirmed that enhancing soil compaction significantly improves soil stability, effectively increases the overall strength and stability of the barriers, reduces deformation, and significantly enhances safety performance. This study not only validates the effectiveness of the reinforcement scheme but also provides new perspectives for the scientific research of safety barriers and offers crucial technical support for the optimal design of road safety protection facilities.

Human decision-making is increasingly supported by artificial intelligence (AI) systems. From medical imaging analysis to self-driving vehicles, AI systems are becoming organically embedded in a host of different technologies. However, incorporating such advice into decision-making entails a human rationalization of AI outputs for supporting beneficial outcomes. Recent research suggests intermediate judgments in the first stage of a decision process can interfere with decisions in subsequent stages. For this reason, we extend this research to AI-supported decision-making to investigate how intermediate judgments on AI-provided advice may influence subsequent decisions. In an online experiment (N=192), we found a consistent bolstering effect in trust for those who made intermediate judgments and over those who did not. Furthermore, violations of total probability were observed at all timing intervals throughout the study. We further analyzed the results by demonstrating how quantum probability theory can model these types of behaviors in human-AI decision-making and ameliorate the understanding the interaction dynamics at the confluence of human factors and information features.

We introduce two symmetric concepts to physics: “distance” (space and time in one) and “wavematter” (electromagnetic wave packet and matter in one). We claim that physics has chosen the wrong concept of time: It is not aware that the time of a moving object flows in a direction other than my time. We provide 15 proofs for our claim by solving 15 mysteries of physics graphically! For example, we prove that length contraction and time dilation are actually geometrical effects in a 4D manifold that we call “Euclidean spacetime” (ES). We prove that the discrepancy in calculating the Hubble constant stems from a systematic error in the redshift measurement. We prove that what I deem wave, deems itself matter, which solves wave–particle duality. We even untangle quantum entanglement without the issue of non-locality. We finally understand why alternative theories of Euclidean relativity have failed: They are all based on four dimensions of space rather than distance. A huge amount of energy was injected into ES at a point that we take as origin. Ever since has this energy been moving radially away at the speed of light. We live in the 3D hypersurface of an expanding 4D hypersphere. Hyperspherical coordinates have the great advantage that they reduce all that is ever happening to just one formula. So, it is the Theory of Everything in these coordinates: “Energy is covering radial distance which, divided by Euclidean time, is equal to the speed of light.” Acceleration and force like gravitation emerge from a rotation of objects in ES and a subsequent projection to 3D space. Matching the symmetry simplifies physics.

A recent finding, based on empirical data of 153 rotationally supported galaxies, with very different morphologies, masses, sizes, and gas fractions, revealed that the baryonic and the dark matter in galaxies are strongly coupled, such that, if the first is known, the second follows and vice versa. Here, we propose a completely theoretical analysis of the dynamics of rotationally supported galaxies, which results in the same conclusion. We find that the relationship between baryonic and dark matter densities at any radius r is governed by the law, ρ(r)_M + ρ(r)_DM = ρ_0, where ρ(r)_M, and ρ(r)_DM are, respectively, the densities of matter and dark matter at radius r, and ρ_0 is the density at the galaxy’s center. Strikingly, we also found that the radius r_s, at which the rotation velocity is equal to half of its maximal value, constitutes a vivid signature of the galaxy, in the sense that it reveals rich information about the galaxy’s dynamics, including the distribution of its matter and dark matter and their total amounts in the galaxy.

The environmental conditions to which dams are exposed play a major role in dictating the progression and manifestation of the alkali-aggregate reaction (AAR). However, in the numerical thermal-mechanical simulation of AAR affected dams, the solar radiation and its associated shadow effects have received little attention. The spatiotemporal distribution of the solar radiation incidence on the dam surfaces has often been addressed in a simplified way or has just been neglected. Yet, far less attention has been given to shadows cast by the dam’s own geometry or the slopes. To illustrate the influence of the nonuniform temperature distribution on dam surfaces due to solar radiation and shading, the analysis of an AAR affected arch dam is presented in this paper.

In view of the limitations of the existing optimization method of suspender cable force, in order to improve the stress of suspender under completion state and avoid frequent adjustment of cable force and grid beam elevation during construction, a new method of cable force optimization is proposed. The article takes the longest large span arch bridge in the world, Pingnan Third Bridge, a Concrete-filled steel tube (CFST) arch bridge with a span of 575m as the engineering background combined with the finite element analysis and multi-objective optimization method. One cable force optimization method that suspender “Real-time correction during construction, in the process variable optimal and results reliable” during panel girder lifting of long span CFST arch bridges is clarified. Taking the panel girder weight and displacement during the construction as parameter variables, the displacement and unevenness of the panel girder under completion state as constraint conditions, the displacement and cable force during the hoisting construction as the objective equation, through the optimization of the objective equation, the suspender cable force and dis-placement of each hoisting section are calculated. The results show that it is feasible to introduce the optimization theory into the cable force optimization when lifting the panel girder. the segment displacement variation is minimized to meet the destination. The cable force distributed evenly under completion state of the bridge that further making sure the completion state satisfies the requirements. No repeating iteration is needed, thus avoiding cumberso me calculation, getting cable force once. With higher optimization efficiency and better effects, the method provides high value for the cable force calculation of same type bridge suspender construction and for guiding construction.

Keywords: Artificial Intelligence in Implantology; AI in Dental Implantology; Machine Learning in Dental Implantology; Deep Learning in Implant Dentistry; Robotics in Dental Implantology; AI-Based Implant Planning.

Porous structured metallic implants are preferable as bone graft substitutes due to their faster tissue integration mediated by bone in-growth and vascularization. The porous scaffolds/ implants should also mimic the graded structure of natural bone to ensure a match of mechanical properties. This article presents a method to design graded porous structured acetabular implant and identifies the suitable parameters for manufacturing the model through additive manufacturing. The design method is based on slice-wise modification to ensure continuity of gradation. Modification of the slices was achieved through the binary image processing route. A geodesic dome type design was adopted for developing the acetabular cup model from the graded porous structure. The model had a solid shell with the target porosity and pore size gradually changing from 65% and 950 µm, respectively, in the inner side to 75% and 650 µm, respectively, towards the periphery. The required dimensions of the unit structures, and the combinations of pore structure and strut diameter to obtain the target porosity and pore size were determined analytically. Suitable process parameters were identified to manufacture the model by Direct Metal Laser Sintering (DMLS) using Ti6Al4V powder after carrying out a detailed experimental study to minimize the variation of surface roughness and warping over different build angles of the strut structures. A dual contour scanning was implemented to simplify the scan strategy. The minimum diameter of struts that could be manufactured using the selected scanning strategy and scanning parameters was found to be 375 µm. Finally, the model was built and from the micro-CT data, the porosities and pore sizes were found to be closely conforming to the designed values. The stiffness of the structures, as found from compression testing, was also found to be well matching with that of human trabecular bone. Further, the structure exhibited compliant bending-dominated behavior under compressive loading.

Background: Actually, resonance frequency analysis (RFA) is the most extended method for measuring implant stability. The implant stability quotient (ISQ) is the measure obtained by the different RFA devices, however, inter- and intra- rater reliability and validity of some devices remains unknown. Methods: Thirty implants were placed in 3 different pig mandibles. ISQ was measured axial and parallel with Osstell® Beacon, Penguin® and MegaISQ® by 2 different operators and one operator performed a test-retest. Intraclass correlation coefficient was calculated to assess the intra- and inter-rater reliability. Pearson correlation coefficient was used to assess the validity. Results: The higher inter- and intra- rater reliability was obtained by Penguin® when measuring axial. The highest ISQ values were obtained using Penguin® in an axial measurement; the lowest, using the MegaISQ® in an axial measurement. The highest correlation values with the other devices were obtained by MegaISQ® measuring axially. Conclusion: Penguin® had a good reliability for measuring ISQ both inter- and intra- rater. Osstell® had good validity for measuring ISQ both axial and parallel and MegaISQ® had the best validity for measuring ISQ axial.

The BP neural network and PSO algorithm are applied into analyzing the reliability of long-span Concrete Filled Steel Tubular (CFST) arch bridges. Firstly, using BP neural network to fit the structural performance function. And then the PSO method was used to calculate the reliability index. A long-span Concrete Filled Steel Tubular arch bridges reliability indices were calculated whether considering the geometric nonlinearity or not. The calculation and analysis results showed that the BP neural network and PSO algorithm compensated the deficiency of the traditional reliability analysis methods, improved the calculation accuracy, provided a new thought and means for the research on the reliability of long-span bridge structure, and well applied to the reliability analysis of long-span Concrete Filled Steel Tubular arch bridges. Additionally, the reliability analysis of long-span Concrete Filled Steel Tubular arch bridges on service limit state must consider the geometric nonlinearity effect, or the results will tend to be unsafe.

The aim of the present study was to monitor implant stability after sinus floor elevation with two biomaterials during the first 6 months of healing by a resonance frequency analysis (RFA), and how physico-chemical properties affect the implant stability quotient (ISQ) at the placement and healing sites. Bilateral maxillary sinus augmentation was performed in 10 patients in a split-mouth design using a bobine HA (BBM) as a control and porcine HA (PBM). Six months after sinus lifting, 60 implants were placed in the posterior maxilla. The ISQ was recorded on the day of surgery from RFA at T1 (baseline), T2 (3 months), and T3 (6 months). Statistically significant differences were found in the ISQ values during the evaluation period. The ISQ (baseline) was 63.8±2.97 for BBM and 62.6±2.11 for PBM. The ISQ (T2) was ~ 73.5±4.21 and 67±4.99, respectively. The ISQ (T3) was ~ 74.65±2.93 and 72.9±2.63, respectively. All the used HAs provide osseointegration and statistical increases in the ISQ at baseline, T2 and T3 (follow-up), respectively. The BBM, sintered at high temperature with high crystallinity and low porosity, presented higher stability, which demonstrates that variations in the physico-chemical properties of a bone substitute material clearly influence implant stability.

Treatment of the [AuCl(tetrahydrothiophene)] complex with 4-chloro-2-iodo-1-isocyanobenzene furnished the gold(I) compound [AuCl(CNC6H3-4-Cl-2-I)] (1). In the crystal structure of 1, the linear C–Au–Cl group is subject to the solid-state head-to-tail pairing which is determined by the aurophilic Au···Au and the rare π-holeCN···Cl interactions. These two types of structure-determining interactions are complementary to each other and the system of Au···Au and CCN···Cl contacts accomplishes 2D extended ladder-type architecture. In addition, the terminal I-atoms are involved in the three-center halogen bonding. Density functional theory calculations, employing a set of computational tools, verified the role of Au···Au and π-holeCN···Cl noncovalent bonds in the spectrum of noncovalent forces.

In this research paper we describe the development phase of a low-cost LoRa IoT solution applied to a kindergarten school with three years results. A set of sensors solution was developed in a LoRa communication board, battery powered, providing a simplified setup process. These sensors were used in order to measure temperature, humidity, luminosity, air quality and presence. Also, energy monitor solutions were integrated. The acquired data is transmitted and analysed for knowledge extraction, identifying savings and other related KPIs. From data, automatic saving actions were performed towards heating and cooling systems, lighting and a set of if-then actions were developed for automatic cost-saving actions, based on infrared signals to heating/cooling systems using some procedure of external command devices. This approach avoids the usage of proprietary vendor solutions in a flexible approach that can easily be deployed to any building facility. This is an important achievement since most of the building consumption is based on heating and cooling systems. In a three years test of the solution, the total energy consumption savings surpassed 20%

Objectives: Treatment of aortic pathologies involving the distal ascending aorta, aortic arch, and descending aorta remains a complex and challenging procedure. Appropriate management is important to achieve satisfactory outcome. Surgical management aims to reduce the time of circulatory arrest. The optimal level of hypothermia is still a matter of debate. The present meta-analysis shows the influence of different temperature levels on mortality and morbidity following aortic arch surgery. Methods: We performed a meta-analysis of published data between January 2000 and March 2020 based on a literature research. 120 studies were included with a total of 32 323 patients divided into three different groups of systemic hypothermia (temperature group 1: ≥ 25 °C, temperature group 2: 25-20°C, temperature group 3: ≤ 20°C) were used for statistical analysis. Results: Early mortality was lowest in temperature group 1 compared to group 2 (OR = 1.42; 95% CI, 1.09-1.85; p=0.01) and group 3 (OR = 1.74; 95% CI, 1.20–2.52; p=0.003). Perioperative stroke appeared to be less frequently in temperature group 1 versus group 2 (OR = 1.48; 95% CI, 1.20-1.82; p=0.0002) and group 3 (OR = 1.61; 95% CI, 1.19 - 2.18; p=0.002). Similar results are obtained concerning new renal insufficiency (group 1 versus group 2: OR = 1.20; 95% CI, 0.91-1.57, p=0.19; group 1 versus 3: OR = 0.94; 95% CI, 0.67 - 1.32, p=0.73) and re-exploration for bleeding (group 1 versus group 2: OR = 1.10; 95% CI, 0.80-1.53, p=0.55; group 1 versus group 3: OR = 1.92; 95% CI, 1.26 - 2.94, p=0,0025). Conclusions: We observed that moderate level of hypothermia during circulatory arrest reduced the incidence of early mortality. Most dreaded neurologic complications occurred less frequently in TG 1. In contrast there was no difference with regards with new onset of renal failure which is commonly accepted as a reliable marker of the quality of visceral organ protection.

Aortic disease has a significant impact on quality of life. Involvement of the aortic arch requires preservation of blood supply to the brain during surgery. Deep hypothermic circulatory arrest is an established technique for this purpose although neurological injury remains high. Additional techniques have been used to reduce the risk although controversy still remains. A three-way cannulation approach, including both carotid arteries and the femoral artery or the ascending aorta, has been used successfully for aortic arch replacement and redo procedures. We have de-veloped circuits of the circulation to simulate blood flow during this type of cannulation set up. The aim is to analyse using CARDIOSIM© cardiovascular simulation platform, how the haemodynamic and energetic parameters are affected and the benefit derived with particular reference to the cerebral circulation.

For dental implant treatment to be successful, esthetics, functionality, and cleanability are all required of the superstructure, the final prosthesis. Screw fixation and cementation have been the conventional methods of choice for the crown prosthesis of implants, but these individual methods cannot fulfill all the requirements. As a solution to this problem, we have devised a new implant superstructure restoration method (inlay covering esthetic technique) using computer-aided design / computer-aided manufacturing inlays. This involves the placement of an inlay covering the access hole in a highly translucent partially stabilized zirconia crown. This technique expands the indications for implant treatment and improves the oral quality of life of patients.

This research explores the development of thermoplastic vulcanizate (TPV) blends derived from natural rubber (NR) and ethylene-butene copolymer (EBC) using a specific blend ratio and melt mixing technique. A comprehensive full factorial design of experiments (DOE) methodology is employed to optimize the processing parameters. TPVs are produced through dynamic vulcanization, combining rubber crosslinking and melt blending within a thermoplastic matrix under high temperatures and shear. The physico-mechanical properties of these TPVs are then analyzed. The objective is to enhance the mechanical performance by assessing the influence of blend ratio, mixing temperature, rotor speed, and mixing time on crucial properties, including tensile strength, elongation at break, compression set, tear strength, and hardness. Analysis of variance (ANOVA) identifies the optimal processing conditions that significantly improve material performance. Validation is achieved through atomic force microscopy (AFM), confirming the phase-separated structure and thus a success of dynamic vulcanization. Rubber process analyzer (RPA) and dynamic mechanical analyzer (DMA) assessments provide insights into the viscoelastic behavior and dynamic mechanical responses. Deconvolution analysis of temperature-dependent tanδ peaks reveals intricate microstructural interactions influencing the glass transition temperature (Tg). The optimized TPVs exhibit enhanced stiffness and effective energy dissipation capabilities across a wide temperature range, making them suitable for applications demanding thermal and mechanical load resistance. This study underscores the pivotal role of precise processing control in tailoring the properties of NR/EBC TPVs for specialized industrial uses. It highlights the indispensable contribution of the DOE methodology to TPV optimization, advancing material science and engineering, particularly for industries requiring robust and flexible materials.

Nanoparticles of platinum-group metals (PGM) on carbon supports are widely used as catalysts for a number of chemical and electrochemical conversions on laboratory and industrial scale. The newly emerging field of single atom catalysis focuses on the ultimate level of metal dispersion, i.e. atomically dispersed metal species anchored on the substrate surface. However, the presence of single atoms in traditional nanoparticle-based catalysts remains largely overlooked. In this work we use aberration-corrected scanning transmission electron microscope to investigate four commercially available nanoparticle-based PGM/C catalysts (PGM = Ru, Rh, Pd, Pt). We show that in addition to nanoparticles, single atoms are also present on the surface of carbon substrates. These observations raise questions about the role that single atoms play in conventional nanoparticle PGM/C catalysts. We critically discuss the observations with regard to the quickly developing field of single atom catalysis.

In recent years, CPU caches have revealed themselves as one of the most powerful sources of information leakage. This information leakage affects any implementation whose memory accesses, to data or instructions, depend on sensitive information such as private keys. In most cases, side-channel cache attacks do not require any specific permission and just need access to a shared cache. This fact, combined with the spread of cloud computing, where the infrastructure is shared between different customers, have made these attacks quite popular. In this paper, we present a novel approach to exploit the information obtained from the CPU cache. First, we introduce a non-access attack that provides a 97\% reduction in the number of encryptions required to obtain a 128-bit AES key. Next, this attack is adapted and extended in what we call the encryption-by-decryption cache attack or EBD, to obtain a 256-bit AES key. When EBD is applied to AES-256, we are able to obtain the 256 bits of the key with less than 10000 encryptions. These results make EBD, to the best of our knowledge, the first practical attack on AES-256 and also demonstrate that AES-256 is only about 3 times more complex to attack than AES-128 via cache attacks. In both cases the target is the AES T-table-based implementation, and we also demonstrate that our approach works in a cross-VM scenario.

Fatigue analysis plays a vital role in determining the structural integrity and life of a dental implant. With the use of such implants on the rise, there is a corresponding increase in the number of implant failures. As such, the aim of this research paper is to investigate the life of 3D-printed dental implants. The dental implants considered in this study were 3D printed according to the direct metal laser sintering (DMLS) method. Additionally, a finite element model was developed to study their performance, while fatigue life was predicted using Fe-Safe software®. The model was validated experimentally by performing fatigue tests. The life of the dental implants was analysed based on Normal strain and the Brown-Miller with Morrow mean correction factor algorithm. The model revealed that there was a strong correlation between the FEA and the experimental results. The clinical success of 3D-printed dental implant experimentally is 20.51 years and computationally under Normal strain is 19.89 years and Brown-Miller with Morrow mean correction factor is 26.82 years.

This study evaluated the mechanical strengths of three types of orthodontic micro-implants by analyzing their structural configurations. Thirty micro-implants of three types (diameter 1.5 mm, Types A, B, C) were assessed. All micro-implants were manually driven into artificial bones at an 8-mm depth. The insertion torque (IT), pullout strength (PS), and gripping volume (GV) of each type were measured. Intergroup comparisons and intragroup correlation were investigated by statistical analysis. Type B had the greatest inner–outer diameter ratio (0.67), and Type A had the smallest (0.53). The IT of Type A (5.26 Ncm) was significantly (p = 0.038) lower than that of Type C (8.8 Ncm). There was no significant difference in the pullout strength (p = 0.868). The GV of Type A (9.7 mm3) was significant (p < 0.01) greater than Type C (8.4 mm3). Type C was significant (p < 0.01) greater than Type B (7.2 mm3). Spearman’s rho rank correlation test showed that PS of Type B was correlated significantly with GV. In conclusion, the design of thread and its GV were the important factors on the mechanical strengths of micro-implant.

This review article deals with the design of bioactive calcium phosphate coatings deposited on metallic substrates to produce bone implants. The bioceramic coating properties are used to create a strong bonding between the bone implants and the surrounding bone tissue. They provide a fast response after implantation and increase the lifespan of the implant in the body environment. The first part of the article describes the different compounds belonging to the calcium phosphate family and their main properties for applications in biomaterials science. The calcium to phosphorus atomic ratio (Ca/P)at. and the solubility (Ks) of these compounds define their behavior in a physiological environment. Hydroxyapatite is the gold standard among calcium phosphate materials, but other chemical compositions/stoichiometries have also been studied for their interesting properties. The second part reviews the most usual deposition processes to produce bioactive calcium phosphate coatings for bone implant applications. Plasma spraying is the main industrial process, but magnetron sputtering, pulsed laser deposition, electrospray deposition, electrophoretic deposition, and electrodeposition are also widely studied in academic and industrial research. The last part describes the main physicochemical properties of calcium phosphate coatings and their impact on the bioactivity of bone implants in a physiological environment.

This paper presents a parametric study of the multistorey hydro-powered pump, known as "Bunyip," which has demonstrated significant potential in contributing to rural regions. The study aims to understand the underlying physics of the system and enhance its hydraulic performance. A transient three-dimensional model using the commercial Computational Fluid Dynamics (CFD) tool Ansys-Fluent is utilized to gain insights into the fundamental flow mechanics, operational efficiency, standard capacity, and relative delivery. The investigation involves an initial assessment of performance for three Bunyip devices based on manufacturing data. Parametric analysis is conducted, and a parametric dataset is generated through meticulous application and numerical modelling. The CFD results are validated against experimental data. Three design configurations are considered, and 58 sets of varied input parameters are examined. The best design configuration is evaluated against five cases of conventional hydro-power pump systems. The results indicate that a smaller diameter of the pressure chamber and a higher supply head lead to higher pressure, achieving a target head of 3 m with 15% efficiency and a flowrate of 11.82 l/min.

The polarised emission from AGN jets carries information about the physical conditions at the emitting plasma elements while its temporal evolution probes the physical processes that introduce variability and dynamically modify the local conditions. Here we present the analysis of multi-frequency radio linear and circular polarisation datasets with the aim to exactly quantify the conditions in blazar jets. Our analysis includes both the careful treatment of observational datasets and numerical modelling for the reproduction of synthetic polarisation curves that can be compared to the observed ones. In our approach the variability is attributed to traveling shocks. The emission from the cells of our jet model is computed with radiative transfer of all Stokes parameters. The model also accounts for Faraday effects which map the low-energy particle populations. We present two extreme cases in terms of the significance of Faraday conversion in the production of circular polarisation. As we show, in both regimes the model gives realistic reproduction of the observed emission.

Surface treatment of implants facilitates osseointegration, with nanostructured surfaces exhibiting accelerated peri-implant bone regeneration. This study compared bone-to-implant contact (BIC) in implants with hydroxyapatite (HA), sand-blasted and acid-etched (SLA), and SLA with calcium (Ca)-coated (XPEED®) surfaces. Seventy-five disk-shaped grade 4 Ti specimens divided into three groups were prepared, with 16 implants per group tested in New Zealand white rabbits. Surface characterization was performed using X-ray diffraction (XRD), field emission scanning electron microscopy (FE-SEM), digital microscopy, and a contact angle analyzer. Cell viability, proliferation, and adhesion were assessed using MC3T3-E1 cells. Apatite formation was evaluated using modified simulated body fluid (m-SBF) incubation. After 4 weeks of healing, the outcomes reviewed were BIC, bone area (BA), removal torque tests, and histomorphometric evaluation. Microstructure analysis revealed irregular pores across all groups, with the XPEED group exhibiting a nanostructured Ca-coated surface. Surface characterization showed a crystalline CaTiO3 layer on XPEED surfaces, with evenly distributed Ca penetrating the implants. All surfaces provided excellent environments for cell growth. The XPEED and SLA groups showed significantly higher cell density and viability with superior osseointegration than HA (p &lt; 0.05); XPEED exhibited the highest absorbance values. Thus, XPEED surface treatment improved implant performance, biocompatibility, stability, and osseointegration.

The present review compared the efficacy of soft tissue substitutes (STS) and autogenous free gingival graft (FGG) or connective tissue graft (CTG) in mucogingival procedures to increase keratinized tissue (KT) width around teeth and implants. Two independent examiners performed the electronic search on Medline and Cochrane Library based on the following PICO’s format: (P) adult patients; (I) soft tissue substitutes and FGG/CTG; (C) STS vs CTG; STS vs FGG; STS vs CTR; (O) KT width gain; (S) Systematic Reviews, Randomized Controlled Trials. Results showed that around teeth, all biomaterials showed superior performance compared to CAF alone for treating gingival recessions. However, when compared to CTG, ADM yields the most similar outcomes to the gold standard (CTG), even though in multiple recessions CTG still continue to be considered the most favorable approach. Use of STSs (acellular matrix or tissue engineered) in combination with an apically positioned flap resulted in a significantly less gain of KTW compared to what achieved with FGG and APF. Around dental implants, free gingival grafts were deemed more effective than soft tissue substitutes in enhancing keratinized mucosa width.

Breast cancer is the most common cancer in women globally, often necessitating mastectomy and subsequent breast reconstruction. Silicone mammary implants (SMIs) play a pivotal role in breast reconstruction, yet their interaction with the host immune system and microbiome remains poorly understood. This study investigates the impact of SMI surface topography on host antimicrobial responses, wound proteome dynamics, and microbial colonization. Biological samples were col-lected from ten human patients undergoing breast reconstruction with SMIs. Mass spectrometry profiles were analyzed for acute and chronic wound proteomes, revealing a nuanced interplay between topography and antimicrobial respondseproteins. 16S rRNA sequencing assessed mi-crobiome dynamics, unveiling topography-specific variations in microbial composition. Surface topography alterations influenced wound proteome composition. Microbiome analysis revealed heightened diversity around rougher SMIs, emphasizing topography-dependent microbial inva-sion. In vitro experiments confirmed staphylococcal adhesion, growth, and biofilm formation on SMI surfaces, with increased texture correlating positively with bacterial colonization. This comprehensive investigation highlights the intricate interplay between SMI topography, wound proteome dynamics, and microbial transmission. The findings contribute to understanding host-microbe interactions on SMI surfaces, essential for optimizing clinical applications and minimizing complications in breast reconstruction.

The clinical application of Phentolamine Mesylate (PM) as an anaesthetic reversal agent has been documented in paediatric patients and in conservative dentistry, but no studies have been found in implant surgery. A prospective randomised study was conducted in 60 patients eligible for mandibular implant treatment, randomly divided between the Control Group (CG) and Experimental Group (EG), who were administered PM. Haemodynamic changes, adverse effects and patient satisfaction were assessed. No statistically significant differences in haemodynamic changes and postoperative pain were found between CG and EG (p&lt;0.05), except for Systolic Blood Pressure (SBP) which increased slightly in EG, without posing a risk to the patient. There were no differences in the presence of adverse effects between the two groups, except in the CG which presented greater difficulty in chewing and biting (p&lt;0.05) and the EG with greater pain in the injection area (p=0.043). 83.3% of the EG patients would request PM again for future dental treatment. The use of PM offers an alternative in implant surgery, without increasing the risks and increasing the patient's quality of life.

This paper studies the dynamic response of corner supported modular steel buildings with a core wall system, under progressive collapse scenarios, associated with corner module removals. Since using secondary systems such as concrete core in mid- to high-rise buildings is currently una-voidable, understanding their impact on load transfer between modules during collapse scenarios becomes essential. The designated buildings with four-, eight- and twelve-story were modelled using the macro-model based finite element method in Abaqus. Also, three different locations are considered for the concrete shear core within the building plan, leading to nine various case scenarios. Each vertical and horizontal inter-module connection was modelled by one axial and two shear springs with predefined nonlinear force-displacement behaviour. The local and global buckling, which plays an essential role in the building's stability, was considered to obtain accurate results. Finally, parametric studies on the building response were carried out, including the intra-module connection rigidity and inter-module connection stiffness. The results demonstrated that the core wall could maintain the robustness of modular steel building through two mechanisms dependent on its location within the plan. Also, preventing plastic hinges from forming in beams could be introduced as an anti-collapse mechanism in the corner module removal scenarios

Sodium-potassium (NaK) liquid alloy is a promising candidate for use as anode material in sodium batteries because of its fluidity, which effectively suppresses the growth of sodium or potassium dendrites. However, the poor wettability of the NaK liquid alloy on conventional metal substrates is unfavorable for cell fabrication due to its strong surface tension. In this paper, low-density and low-cost fluorinated aluminum foam is used as a substrate support material for NaK liquid alloy. By combining low surface tension NaK@C with fluorinated aluminum foam, we obtain a uniformly distributed and structurally stable electrode material. The composite electrode has a cycling stability of more than 3000 hours in a symmetrical cell. Furthermore, when coupled with a sulfurized polyacrylonitrile cathode in carbonate electrolyte, it maintains excellent stability even after 800 cycles, with 72% of capacity retention.

Assessment of meadow restoration benefits from understanding the connection between geomorphology, hydrology and vegetation, and multispectral imagery captured from unpiloted aerial vehicles (UAV) may provide the method most suitable in terms of cost, spatial resolution, support for vegetation indices, and frequency of acquisition. Our field studies of northern Sierra Nevada montane meadows (with <40 km2 watersheds) in various stages of restoration includes GPS + laser-leveling channel survey, laser-leveled cross section, aerial LiDAR, vegetation sampling, soil measurements, and UAV imaging using a sensor capturing calibrated blue (465-485 nm), green (550-570 nm), red (663-673 nm), near infrared (820-860 nm), and red edge (712-722 nm) bands at 5.5 cm resolution, providing multispectral false-color images and vegetation indices such as normalized difference vegetation index (NDVI) and red-edge Chlorophyll index (Clre). This fine-scale imagery extends our morphometric assessment of post-restoration channel scouring exhibiting bedform patterns and sinuosity related to Carex-influenced soil properties and Salix copses, but also provided a view of groundwater-related drainage effects including sinuous Carex-vegetated zones evident from spring snowmelt images as well as NDVI and Clre in growing to senescent phenological stages. Carex in particular was significantly associated with low bulk density and high soil moisture, NDVI, and Clre at lower elevations.

This paper presents the design and measurement of an IEEE 802.11ad standard compatible RF transceiver for 60GHz wireless communication system. In addition to the traditional half-duplex (HD) mode, this work supports full-duplex (FD) operation to deliver better channel utilization and faster response time for the system. The isolation between the transmitter and receiver from the architecture design to system integration for FD operation has been fully considered. A digital self-interference cancellation (DSIC) is implemented in MATLAB to verify the FD performance. The super-heterodyne architecture with an intermediate frequency (IF) of 12GHz is designed to suppress the image frequencies without using extra filters. A flexible phase-locked loop (PLL) synthesizer provides a local oscillator (LO) frequency with a 2kHz resolution. Other than the time division duplex (TDD) mode used in the conventional 60GHz system, a wide bandwidth baseband digital variable gain amplifier (DVGA) with a 3dB bandwidth of more than 4GHz also supports frequency division duplex (FDD) operation. The transceiver chip is fabricated in Tower Jazz 0.18µm SiGe BiCMOS process. With on-board antenna, the transceiver covers all four channels in 802.11ad standard with MCS-12 (7.04Gbps under 1.76GSym/s and 16-QAM) under 1.5m. In the proposed system design, the RF frontend based self-interference (SI) suppression from the local transmitter to receiver LNA is around 54dB. To achieve a practical FD application, the SI is further suppressed with the help of digital SI compensation. The measured power consumption for transmitter and receiver configuration is 194mW and 231mW, respectively, in HD mode and 398mW for FDD or FD operation mode.

With an increased interest in applications that require a clean background image, such as video surveillance, object tracking, street view imaging and location-based services on web-based maps, multiple algorithms have been developed to reconstruct a background image from cluttered scenes. Traditionally, statistical measures and existing image quality techniques have been applied for evaluating the quality of the reconstructed background images. Though these quality assessment methods have been widely used in the past, their performance in evaluating the perceived quality of the reconstructed background image has not been verified. In this work, we discuss the shortcomings in existing metrics and propose a full reference Reconstructed Background image Quality Index (RBQI) that combines color and structural information at multiple scales using a probability summation model to predict the perceived quality in the reconstructed background image given a reference image. To compare the performance of the proposed quality index with existing image quality assessment measures, we construct two different datasets consisting of reconstructed background images and corresponding subjective scores. The quality assessment measures are evaluated by correlating their objective scores with human subjective ratings. The correlation results show that the proposed RBQI outperforms all the existing approaches. Additionally, the constructed datasets and the corresponding subjective scores provide a benchmark to evaluate the performance of future metrics that are developed to evaluate the perceived quality of reconstructed background images.

Two methods for Pd nanoparticle synthesis were explored with three different carbide-derived carbon (CDC) support materials of which one was nitrogen-doped. These materials were studied for oxygen reduction reaction (ORR) in 0.1 M KOH solution. The prepared CDC/Pd catalysts were characterized using TEM, XRD and XPS. Using these methods, we can observe the influence of support materials for one-pot synthesis methods as we use the standard citrate method and polyol method with polyvinylpyrrolidone (PVP) as a capping agent. Comparing the two methods N-doping of carbon material resulted in smaller nanoparticles only in the case of citrate synthesis, suggesting that the influence of support is weaker using polyol method. Citrate method on CDC1, which was predominantly microporous led to a higher degree of agglomeration and larger particle formation in comparison to CDC2 and CDC3 supports, which possessed higher degree of mesoporosity. Smaller Pd particle sizes were achieved using citrate and NaBH4 in comparison to the ethylene glycol-PVP method. CDC2 and CDC3 did not show significant difference suggesting that the N-doping did not have much of an influence on the ORR. Highest SA value was observed on CDC1/Pd_Cit, which could be attributed to formation of larger particles and agglomerates.

Medical implants made of biodegradable materials could be of advantage for temporary applications such mechanical support during bone-healing or as vascular stents to keep blood vessels open. After completion of the healing process the implant would disappear, avoiding long-term side effects or the need for surgical removal. Various corrodible metal alloys based on magnesium, iron or zinc have been proposed as sturdier and potentially less inflammatory alternative to degradable organic polymers, in particular for load-bearing applications. Despite the recent introduction of magnesium-based screws the remaining hurdles to routine clinical applications are still challenging, such as limiting mechanical material characteristics or unsuitable corrosion characteristics. Here, salient features and clinical prospects of currently investigated biodegradable implant materials are summarized with a main focus on magnesium alloys. A mechanism of action for the stimulation of bone growth due to the exertion of mechanical force by magnesium corrosion products is discussed. To explain divergent in vitro and in vivo effects of magnesium a novel model for bacterial biofilm infections is proposed which predicts crucial consequences antibacterial implant strategies.

Smart materials represent an elegant class of (macro)-molecules endowed with the ability to react to chemical/physical changes in the environment. Herein, we prepared new photo responsive azobenzenes possessing halogen bond donor groups. The X-ray structures of two molecules highlight supramolecular organizations governed by unusual noncovalent bonds. In azo dye I-azo-NO2, the nitro group is engaged in orthogonal H···O···I halogen and hydrogen bonding, linking the units in parallel undulating chains. As far as compound I-azo-NH-MMA is concerned, a non-centrosymmetric pattern is formed due to a very rare I···π interaction involving the alkene group supplemented by hydrogen bonds. The Cambridge Structural Database contains only four structures showing the same I···CH₂=C contact. For all compounds, an ¹⁹F NMR spectroscopic analysis confirms the formation of halogen bonds in solution through a recognition process with chloride anion, and the reversible photo-responsiveness is demonstrated upon exposing a solution to UV light irradiation. Finally, the intermediate I-azo-NH2 also shows a pronounced color change due to pH variation. These azobenzenes are thereby attractive building blocks to design future multi-stimuli responsive materials for highly functional devices.

A new teaching method under the name of STEM, integrating the disciplines of Science, Technology, Engineering, and Mathematics, is now taught by teachers in their classes. Considering that the generation that grows up in the 21st-century has grown up with technology, it is thought that integrating technology into lessons helps students learn the subject. The study aims to develop five STEM activities for the human body systems lesson by integrating the coding-based Arduino into STEM education. The activities were implemented to 6th-grade students for seven weeks and the effects on students' skills of establishing a cause-effect relationship. The study method was pre-test-post-test quasi-experimental design, and the cause-effect relationship scale was used as a data collection tool. As a result of the study, a significant difference was found between the Arduino-supported STEM activities developed and the students' skills of establishing a cause-effect relationship.

Basketball is a highly anaerobic game, that consists of high-intensity efforts followed by lower-intensity efforts. Postural deformities can be a limiting factor in achieving maximal performances in basketball. Flat feet are one of the most common deformities and they can lead to poorer performances, discomfort and pain. In this research we made an attempt to link the degree of feet flatness with sports performances among Icelandic adolescent basketball players. A sample of 100 basketball players was tested on a podoscope to establish the degree of feet flatness and all participants performed countermovement jump, 20m sprint and pushups in 30 seconds. No significant correlation was observed between feet status and sports performances. No differences were found between groups with and without flat feet, which indicates that feet flatness was not a limiting factor in achieving better results. However, we state that only strong and healthy feet might lead to excellent performance.

The first treatments with dental implants had low success rates (75%). Nowadays, oral rehabilitation with titanium dental implants has a high success rate (95-98%). The success rate significantly increases due to increased scientific knowledge about osseointegration, changes in surgical techniques, and the development of implant surface treatments. Despite the high success rate of implants, no protocol defines the time for the prosthesis to be installed and loaded after surgery. This work compares a new dental implant's primary (mechanical) and secondary (osseointegration) stability. Dental implant with micro- and nano-roughness surface was placed in 24 patients with a minimum of 35 N.cm and a maximum of 60 N.cm. Primary stability was quantified with a torque wrench and Ostell Mentor. The secondary stability 45 and 60 days after surgery was measured with Ostell. The results showed no statistical difference in secondary stability at 45 and 60 days postoperatively among implants. The success rate of dental implants can be associated with the surface morphology with micro and nano-roughness and the shape of the fillets of the implant threads. When the manufacturer's guidelines are followed, it is possible to prosthetically rehabilitate the patient with an implant 45 days after surgery.

Currently the bimatoprost implant (DURYSTA) is approved for a single administration secondary to concern for progressive corneal endothelial cell (CEC) loss with intracameral administration. In order to better understand the cause of CEC loss and other adverse events (AEs) with intracameral administration, multimodal imaging of the implant utilizing optical coherence topography (OCT), robotic ultrasound and bio microscopy video recording was utilized. Inherently the anterior chamber is a non-confined space. In certain examples the implant assumed a round and spotted structure as it picked up iris pigment as it migrated around the anterior chamber. Accordingly, we explored delivery of the implant in the middle segment behind the iris and in front of the pseudophakic lens. We then evaluated the suitability of various imaging modalities to assess the implant in this location. For middle segment administration, the ArcScan Insight 100 robotic ultrasound provided resolution and repeatability sufficient to monitor the implant behind the iris. This preliminary study hypothesizes that DURYSTA migration in the anterior chamber is the main source of AEs. Through use of a confined location, the middle segment, the implant is unlikely to migrate and cause CEC loss while also delivering drug closer to its site of action, the ciliary body. Further efforts are underway to understand the suitability of the middle segment for serial DURYSTA administration to maximize intraocular pressure lowering while minimizing AEs.

Considering that consumers are more willing to buy products online, companies are increasingly selling remanufactured products online through e-commerce platforms. Notwithstanding the high attention it elicits from researchers and companies, the study about the remanufacturing trading platform is in its infancy. Thus, we investigate 20 remanufacturing trading platforms related nowadays and make a gap analysis among them in terms of: (i) business model, (ii) product display, (iii) delivery products, (iv) quality assurance and after-sales service, (v) product review and star rate and (vi) transaction and payment. On this basis, we analyze features and trends for the development of remanufacturing trading platforms and propose six key applications aimed at filling the identified gaps. The consortium blockchain has the characteristics of security and transparency, high credibility, traceability and unfalsifiability, low cost, and strong scalability, which can provide effective support for the six key applications. Then, we construct the technical framework and the model of a consortium blockchain-supported remanufacturing trading platform. Further, we analyze the coupling mechanism between consortium blockchain and remanufacturing trading platform to explain how the remanufacturing trading platform supported by consortium blockchain achieves development characteristics. This study provides important guidance for the development, construction, and operation management of remanufacturing trading platforms.

This paper proposes a curved link-slab (CLS) structure, simplified into a hingeless-arch model, to address the current cracking phenomenon of CLS concrete. The stress formula of the hingeless arch under various loads is derived based on the classical mechanic's method. Based on an actual bridge example, the mechanical properties of CLS are analyzed under different loads and load combinations. The results show that: (1) the CLS stress is significantly lower than that of the flat link-slab structure (FLS), (2) its stress values are less than the concrete tensile limit, and (3) the CLS can effectively solve the concrete cracking phenomenon on the link-slab. The rationality of the stress formula derived from the simplified model of the hingeless arch is verified using the finite element method (FEM). The parametric sensitivity analysis shows that variation of the reinforcement ratio of the CLS has a limited impact on it. Considering both the concrete tensile and compressive limit, the thickness of the CLS should be 15 cm to 20 cm, and its design span should be about 5% to7.5% of the main beam length.

Business Intelligence, defined by [1] as "the ability to understand the interrelations of the facts that are presented in such a way that it can guide the action towards achieving a desired goal", has been used since 1958 for the transformation of data into information, and of information into knowledge, to be used when making decisions in a business environment. But, what would happen if we took the same principles of business intelligence and applied them to the academic environment? The answer would be the creation of Academic Analytics, a term defined by [2] as the process of evaluating and analyzing organizational information from university systems for reporting and making decisions, whose characteristics allow it to be used more and more in institutions, since the information they accumulate about their students and teachers gathers data such as academic performance, student success, persistence, and retention [5]. Academic Analytics enables an analysis of data that is very important for making decisions in the educational institutional environment, aggregating valuable information in the academic research activity and providing easy to use business intelligence tools. This article shows a proposal for creating an information system based on Academic Analytics, using ASP.Net technology and trusting storage in the database engine Microsoft SQL Server, designing a model that is supported by Academic Analytics for the collection and analysis of data from the information systems of educational institutions. The idea that was conceived proposes a system that is capable of displaying statistics on the historical data of students and teachers taken over academic periods, without having direct access to institutional databases, with the purpose of gathering the information that the director, the teacher, and finally the student need for making decisions. The model was validated with information taken from students and teachers during the last five years, and the export format of the data was pdf, csv, and xls files. The findings allow us to state that it is extremely important to analyze the data that is in the information systems of the educational institutions for making decisions. After the validation of the model, it was established that it is a must for students to know the reports of their academic performance in order to carry out a process of self-evaluation, as well as for teachers to be able to see the results of the data obtained in order to carry out processes of self-evaluation, and adaptation of content and dynamics in the classrooms, and finally for the head of the program to make decisions.

Spin valves with a synthetic antiferromagnet were fabricated by magnetron sputtering. It was shown that the fabricated spin valves had perfect microstructure of layers and smooth interfaces, therefore RKKY interaction dominates in coupling of ferromagnetic layers separated by a copper spacer. Rhombus-shaped microobjects were fabricated from a single spin valve film. The thermomagnetic treatment procedure was found, to form unidirectional anisotropy in the microobject so, that the values of the exchange bias fields in the rhombus’ nonparallel sides were opposite in sign. For the synthetic antiferromagnet CoFeNi/Ru/CoFeNi the difference between ferromagnetic layers thicknesses was found, at which the thermomagnetic treatment forms the same exchange bias all over the rhombus’ side. The sensor element was fabricated in which each side of the rhombus was a shoulder of a Wheatstone bridge. After the thermomagnetic treatment procedure each shoulder worked as an active magnetosensitive element, thus the device operated as the full Wheatstone bridge. The sensor output has the shape of a step, high sensitivity to field change and significant magnetic hysteresis. Such characteristics are suitable for switching devices.

Silver nanoparticles from Origanum vulgare (Oregano) have been synthesized in the past. However, no investigation has been performed on the combined effects of independent factors that affect the synthesis. Silver nitrate and Oregano concentrations, incubation temperature and time, as well as pH can play crucial roles in synthesis. In this regard Full Factorial Design was applied. A Voigt function was fitted on the measured UV – Vis spectra. The fitting parameters of the Voigt function (peak wavelength, area, and Full Width at Half Maximum) were used as the responses. A quadratic model was fitted for the peak wavelength and area, and the pH proved the dominant factor on nanoparticle synthesis.

Plankton monitoring by microscopy offers long-term ecological perspective of plankton communities but is biased towards those organisms that can be distinguished using the microscope. Genetic identification of marine plankton has become standard but is still not used. This study is a comprehensive study genetically measured taxa in the Western Channel of UK using a small-volume automated water sampler deployed on the CPR platform. The study present one year of high-throughput sequencing data focussing on smaller plankton and separate community to that measured by microscopy that can complement each other for a holistic view of plankton. Quantitative tests of two harmful algae show relatively high abundance of the Pelagophyte Aureococcus anophagefferens during 2011 with low nitrite levels. Three years of Pseudo-nitzschia delicatissima quantitative monitoring also shows a greater abundance of this potentially harmful taxa in 2011. Flow cytometry reveals distinct seasonal cycles with distinct timings.

Plastid gene expression involves many post-transcriptional maturation steps resulting in a complex transcriptome composed of multiple isoforms. Although short read RNA-seq has considerably improved our understanding of the molecular mechanisms controlling these processes, it is unable to sequence full-length transcripts. This information is however crucial when it comes to understand the interplay between the various steps of plastid gene expression. Here, the study of the Arabidopsis leaf plastid transcriptome using Nanopore sequencing showed that many splicing and editing events were not independent but co-occurring. For a given transcript, maturation events also appeared to be chronologically ordered with splicing happening after most sites are edited.

Background: The treatment plan of prosthetic restorations supported by dental implants require comprehensive scientific knowledge to deliver prostheses with good prognosis, even before the implant insertion. This review aims to analyze the main prosthetic determinants of the prognosis of implant-supported prostheses. Methods: A systematic review of the literature was conducted with a PICO question: "For partially or complete edentulous subjects treated with implant-supported prostheses, which prosthetic factors could affect clinical outcomes?". A literature search was performed electronically in PubMed (MEDLINE), Scopus and Cochrane Library with the following equation [PROGNOS* OR RISK] FACTOR IMPLANT DENTAL, and by hand search in relevant journals and throughout the selected papers. Results: This revision was carried out based on 50 papers focused on several prosthodontics-related risk factors that were grouped as follows: implant-connection, loading protocol, transmucosal abutments, prosthetic fit, provisionalization, type of retention, impression technique, fabrication technique, and occlusion. More than a half of the studies were systematic reviews (30%), meta-analysis (16%) or prospective evaluations of prosthesis with various kinds of events (18%). But also narrative reviews of literature (14%) and in vitro/animal studies (16%) were found. Conclusions: The current literature provides insufficient evidence for most of the investigated topics. However, based on the accumulated data, it seems reasonable to defend that the best treatment approach is the use of morse taper implants with transmucosal abutments, recorded by means of rigidly splinted copings through the pick-up technique, and screwed by milled prosthesis occlusally adjusted to minimize functional overloading.

This systematic review investigates the failure rate and marginal bone loss (MBL) of dental implants placed in Solid-organ transplant (SOT) patients compared to healthy controls. Three databases (PubMed, Web of Sciences and the Cochrane Library) were searched up to June 2020 (PROSPERO CRD42019124896). Case-control and cohort studies reporting data failure rate and marginal bone loss (MBL) of dental implants placed in SOT patients were included. The risk of bias of observational studies was assessed through the Newcastle-Ottawa Scale (NOS). Four case-control studies fulfilled the inclusion criteria, all of low risk of bias. Meta-analyses revealed consistently lower implant failure rate than control populations at patient and implant levels. SOT patients had a significant difference of -18% (p-value <0.001) of MLB towards healthy patients. SOT status poses no serious threat to implant survival. Overall, this group of patients presented lower levels of dental implant failure rate and marginal bone loss compared to otherwise healthy patients. Further intervention trials with wider sample size and longer follow-ups are necessary to confirm these summary results.

Purpose: this paper evaluates the effect of thermo-formed aligners with complementary biomechanical attachments (CBA) on periodontal ligaments (PDL) during the expansion process of the maxillary arch using simulations based on the finite element method (FEM). Methods: four types of teeth (canine 3, premolar 4, premolar 5 and molar 6) were modeled using 3D CAD. In addition, aligners, CBAs and PDL were also 3D modeled. With this information, a FEM model was generated, and a clinical rehabilitation scenario was simulated. For the validation of the results, a comparison with medical records was performed. Results: for canine 3, the displacement was 0.134 mm with a maximum stress of 4.822 x10-3MPa in the amelocemental junction. For premolar 4, the displacement was 0.132 mm at a maximum stress of 3.273x10-3MPa in the amelocemental junction. Premolar 5 had a displacement of 0.129 mm and a stress of 1.358 x10-3MPa at 1 mm from the amelocemental junction. Molar 6 had a displacement of 0.124 mm and a maximum stress of 2.440 x10-3MPa. Conclusions: The simulations showed that the use of CBA reduces tooth tipping. The model with Vestibular CBA presented the best results in terms of the dental movement of expansion of the maxillary arch with the use of thermoformed aligners. Significance: Considering the difficulty of performing in vivo tests that evaluate the configuration effectiveness of the different CBA alternatives in thermoformed aligners, FEM techniques were used to reduce time and costs, and get accurate results with minimal errors.

Quantum cell automata (QCA) is a nanotechnology that uses a transistor-free structure to design digital circuits and overcome the limitations listed for CMOS circuits. The computing circuits that make up the bulk of computers can be designed and using this technology. Subtractors are a big part of computational circuits. This research deals with the design of a subtractor that due to the innovation in the design of this circuit and the novel arrangement of quantum cells of its kind has caused the number of cells used in the design of the circuit to reach its lowest value compared to previously designed circuits. The size of the circuit as well as the loss power are minimized compared to the circuits designed by the subtractors. Another trait clears of this circuit compared to many previous designs is its single-layer design, which reduces latency and noise in the output waveform. The circuit designed by the QCADesigner simulator is tested and simulated inadition the results are displayed in the simulated waveform. Also, the results of calculations for power dissipation in each QCA cell were evaluated by QCAPro software, which is a powerful tool for estimating power loss simulation. It has less implementation and level (single layer) than Previous designs.

This paper proposes and demonstrates, in full scale, a novel type of energy geostructure (“the Climate Road”) that combines a ground source heat pump (GSHP) with a sustainable urban drainage system (SUDS) by utilizing the gravel roadbed simultaneously as energy source and rainwater retarding basin. The Climate Road measures 50m x 8m x 1m (length, width, depth) and has 800 m of geothermal piping embedded in the roadbed, serving as the heat collector for a GSHP that supplies a nearby kindergarten with domestic hot water and space heating. Model analysis of operational data from 2018-2021 indicates sustainable annual heat production levels around 0.6 MWh per meter road, with a COP of 2.9-3.1. The continued infiltration of rainwater to the roadbed increases the amount of extractable heat by an estimated 17% compared to the case of zero infiltration. Using the developed model for scenario analysis we find that draining rainwater from three single family houses and storing 30% of the annual heating consumption in the roadbed, increases the predicted extractable energy by 56% compared to zero infiltration with no seasonal energy storage. The Climate Road is capable of supplying three single family houses with heating, cooling and rainwater management year-round.

INTRODUCTION: Breast sensibility following reconstruction surgery, though often overlooked, holds significant importance due to its widespread occurrence and profound effects on patients’ well-being and safety. Our objective is to compare the sensory outcomes between DIEP flap microsurgery reconstruction and implant-based reconstruction. Additionally, we explored the potential influence of sociodemographic and clinical factors on sensory recovery, along with assessing temperature discrimination abilities and evaluating quality of life. MATERIAL AND METHODS: We conducted an ambispective descriptive-analytical study, involving women who underwent mastectomy with reconstruction using either DIEP flap and implants at our hospital between 1990 and 2021. Data were collected from medical records, patient histories, physical examination, and validated quality of life questionnaires (BREAST-Q). RESULTS: A total of 99 women with breast reconstruction were included, 47 with DIEP flap and 52 with implants. Sensory recovery in implant-based reconstruction was found to be superior to DIEP flap reconstruction (5.03 and 5.18 respectively, p-value &lt;0.005). A direct correlation was observed between sensory improvement and thermal discrimination (Spearman coefficient 0.9, p-value &lt;0.001). Factors such as radiotherapy, delayed reconstruction with DIEP flap, and height with implants were associated with poorer sensory recovery in the breast. Women experiencing better breast sensibility reported higher satisfaction with their surgeon, medical team, and psychosocial quality of life. CONCLUSION: Women reconstructed with implants or DIEP abdominal flap exhibit suboptimal overall sensory recovery of the reconstructed breast, with slightly better outcomes observed in women reconstructed with implants.

Recently, the indications for Cochlear Implant (CI) have also been extended to subjects with Single Sided Deafness (SSD) in order to restore binaural hearing. The primary objective of this study was to investigate the advantages of CI following one year of usage in SSD subjects. Secondarily we want to assess the long-term stability of the CI. 57 participants performed a complete audiological assessment (speech audiometry in quiet and in noise and localization test). For each was also evaluated subjective hearing profile (with Speech Spatial and Qualities_SSQ questionnaire) and the impact of tinnitus (with the use of Tinnitus Handicap Inventory_THI questionnaire) After one year of CI usage, we observed a significant improvement in speech-to-noise ratio, in sound localization abilities, in the Speech (p-value 0.001) and Spatial (p-value 0.001) subscales of the SSQ questionnaire and in THI questionnaire (p-value 0.001). The improvements in speech in noise and localization abilities and the reduction of the SSQ and THI questionnaires scores were maintained over time (6th to 60th month follow-up). Only eight participants did not fully utilize the CI. CI in SSD represents an effective method for improving speech recognition in noisy environments, restoring sound localization abilities, reducing tinnitus and improve subjective listening skills.