This paper proposes a metaphysical framework for distinguishing between human and machine intelligence. By drawing an analogy from Kant’s incongruent counterparts, it posits two identical deterministic worlds -- one comprising a human agent and the other comprising a machine agent. These agents exhibit different types of information processing mechanisms despite their apparent sameness in a causal sense. By postulating the distinctiveness of human over machine intelligence, this paper resolves what it refers to as “the vantage point problem” – namely, how to legitimize a determinist’s assertion of determinism by placing the determinist within the universe.

Induction heating is a fast, reproducible, and efficient heating method used in various manufacturing processes. However, there is no established additive manufacturing (AM) process based on induction heating using wire as feedstock. This study investigates a novel approach to AM based on inductive heating, where a steel wire is melted and droplets are detached periodically using a two-winding induction coil. The process parameters and energy input into the droplets are characterized. The induction generator exhibits sluggish response to the excitation voltage, resulting in a lag in the coil current. The process is captured using a high-speed camera, revealing regular droplet formation and uniform size and shape when operated within an appropriate process window. Larger drops and increased spatter formation occur outside this window. The proposed method allows for the production of droplets with almost spherical shapes. Further analysis and characterization of droplet formation and energy input provide insights into process optimization and overall efficiency.

To enhance the applicability of dual-phase high-entropy alloys (HEAs) like Fe32Cr33Ni29Al3Ti3, fabricated via selective laser melting (SLM), a focus on improving their mechanical properties is essential. As part of this effort, heat treatment was explored. This study compares the microstructure and mechanical properties of the as-printed sample with those cooled in water after undergoing heat treatment at temperatures ranging from 1000 to 1200 ℃ for 1 hour. Both pre- and post-treatment samples reveal a dual-phase microstructure comprising FCC and BCC phases. Although heat treatment led to a reduction in tensile and yield strength, it significantly increased ductility compared to the as-printed sample. This strength-ductility trade-off is related to changes in grain sizes with ultrafine grains enhancing strength and micron grains optimizing ductility, also the influence of the content of FCC/BCC phases and dislocation density. In particular, the sample heat-treated at 1000 °C for 1 hour and then water-cooled exhibited a better combination of strength and ductility, a yield strength of 790 MPa, and an elongation of 13%. This research offers innovative perspectives on crafting dual-phase HEA of Fe32Cr33Ni29Al3Ti3, allowing for tailorable microstructure and mechanical properties through a synergistic approach involving SLM and heat treatment.

Depressions containing partially molten rocks were investigated in Quaternary pebbly sedi-ments in Alpine foreland in Bavaria, Germany. Ruins of limekilns from 18-19th centuries are abundant around Seeshaupt. They are usually associated with earthworks for fuel feeding and protection from wind. Depressions contain partially molten stones from furnace walls, with lime and burnt loam remnants. On the surface of pebbles (typically gneisses), green glass formed with chemical composition possibly affected by moderately volatile components of wood biomass, mainly K and Cu. Thermoplastic deformation of pebbles is limited and the sur-face melt deformation points to slow flow. At Emmerting, on the other hand, two walled circu-lar depressions which lack additional earthworks have been identified as possible impact cra-ters. Thermally affected pebbles show much more intense deformation. Colorless to greenish glass, also K and Cu enriched, usually forms only thin surface coatings, in places covered by younger melt extruded from pebble interior. Burnt loam is missing. At Grabenstätt-Kaltenbach, a depression of unclear origin was investigated. Morphologically, it matches craters rather than limekilns, but anthropogenic contamination (brick-like material) is probable. The rare molten samples do not display extreme deformation features. The thermally affected stones, mainly those from Emmerting, have elevated magnetic susceptibility.

Residual stress (RS) is the most challenging problem in metal additive manufacturing (AM) since the build-up of high tensile RS may influence the fatigue life, corrosion resistance, crack initiation, and failure of the additively manufactured components. While tensile RS is inherent in all the AM processes, fast and accurate prediction of stress state within the part is extremely valuable and would result in optimization of the process parameters in achieving a desired RS and control of the build process. This paper proposes a physics-based analytical model to rapidly and accurately predict the RS within the additively manufactured part. In this model, a transient moving point heat source (HS) is utilized to determine the temperature field. Due to the high temperature gradient within the proximity of the melt pool area, material experience high thermal stress. Thermal stress is calculated by combining three sources of stresses known as stresses due to the body forces, normal tension, and hydrostatic stress in a homogeneous semi-infinite medium. The thermal stress determines the RS state within the part. Consequently, by taking the thermal stress history as an input, both the in-plane and out of plane RS distributions are found from incremental plasticity and kinematic hardening behavior of the metal by considering volume conservation in plastic deformation in coupling with the equilibrium and compatibility conditions. In this modeling, material properties are temperature-sensitive since the steep temperature gradient varies the properties significantly. Moreover, the energy needed for the solid-state phase transition is reflected by modifying the specific heat employing the latent heat of fusion. Furthermore, the multi-layer and multi-scan aspects of metal AM are considered by including the temperature history from previous layers and scans. Results from the analytical RS model presented excellent agreement with XRD measurements employed to determine the RS in the Ti-6Al-4V specimens.

In this research, catalytic steam reforming acetic acid derived from the aqueous portion of bio-oil for hydrogen production was investigated by using different Ni/ATC (Attapulgite Clay) catalysts prepared by precipitation, impregnation and mechanical blending methods. The fresh and reduced catalysts were characterized by XRD, N₂ adsorption-desorption, TEM and H₂-TPR. The comprehensive results demonstrated that the interaction between active metallic Ni and ATC carrier was significantly improved in Ni/ATC catalyst prepared by precipitation method, and in which the mean Ni particle size was the smallest (~13 nm) resulted in the highest metal dispersion (7.5%). The catalytic performance of the three catalysts was evaluated through the process of steam reforming of acetic acid in a fixed-bed reactor under atmospheric pressure at two different temperatures, such as 550 ℃ and 650 ℃. Results showed that the Ni/ATC (PM-N/ATC) prepared by precipitation method, achieved the highest H₂ yield of ~82% and little lower acetic acid conversion efficiency of ~85% than that (~95%) of Ni/ATC (IM-NATC) prepared by impregnation method. In addition, the deactivation catalysts after reaction for 4 h were analyzed by XRD, TGA-DTG and TEM, which demonstrated that the catalyst deactivation was not caused by the amount of carbon deposition, but owed to the significant agglomeration and sintering of Ni particles in the carrier.

With the development of industrialization, traditional manufacturing technologies are no longer able to meet the production needs of modern society. Additive manufacturing has successfully solved the problems existing in traditional manufacturing technology. Selective laser melting (SLM) is a powder bed melting technology that produces metal parts by selectively melting metal powders on a platform using a laser beam. It is widely used in additive manufacturing. This article introduces the characteristics and current development status of SLM technology, summarizes the main application fields and common defects of SLM, and finally explores and prospects the future development trend of SLM.

Selective laser melting is an emerging Additive Manufacturing (AM) technology for metals. Intricate three-dimensional parts can be generated from the powder bed by selectively melting the desired location of the powders. The process is repeated for each layer until the part is built. The necessary heat is provided by a laser. Temperature magnitude and history during SLM directly determine the molten pool dimensions, thermal stress, residual stress, balling effect, and dimensional accuracy. Laser-matter interaction is a crucial physical phenomenon in the SLM process. In this paper, five different heat source models are introduced to predict the three-dimensional temperature field analytically. These models are known as steady state moving point heat source, transient moving point heat source, semi-elliptical moving heat source, double elliptical moving heat source, and uniform moving heat source. The analytical temperature model for all of the heat source models are solved using three-dimensional differential equation of heat conduction with different approaches. The Steady state and transient moving heat source are solved using separation of variables approach. However, the rest of models are solved by employing the Green’s functions. Due to the high magnitude of the temperature in the presence of the laser, the temperature gradient is usually high which has a substantial impact on thermal material properties. Consequently, the temperature field is predicted by considering the temperature sensitivity thermal material properties. Moreover, due to the repeated heating and cooling, the part usually undergoes several melting and solidification cycles, this physical phenomenon is considered by modifying the heat capacity using latent heat of melting. Furthermore, the multi-layer aspect of metal AM process is considered by incorporating the temperature history from the previous layer since the interaction of the layers have an impact on heat transfer mechanisms. The proposed temperature field models based on different heat source approaches are validated using experimental measurement of melt pool geometry from independent experimentations. The detailed explanation of the comparison of models is also provided. Moreover, the effect of process parameters on the balling effect is also discussed.

In recent years, compound glass microsphere resonator devices have attracted increasing interest and have been widely used in sensing, microsphere lasers, and nonlinear optics. Compared with traditional silica resonators, compound glass microsphere resonators have many significant and attractive properties, such as high-Q factor, an ability to achieve high rare earth ion, wide infrared transmittance and low phonon energy. This review provides a summary and a critical assessment of the fabrication and the optical characterization of compound glasses and the related fabrication and applications of compound glass microsphere resonators.

Curcumin, found in the rhizome of turmeric, has extensive therapeutic promises via its antioxidant, anti-inflammatory, and antiproliferative properties. Preclinical in vitro and in vivo data have shown curcumin to be an effective treatment for multiple cancers. These effects are drived by curcumin's ability to induce G2/M cell cycle arrest, induction of autophagy, activation of apoptotic pathways, disruption of molecular signaling, inhibition of invasion and metastasis, and by increasing the efficacy of existing chemotherapeutics. Here we focused on the hormetic behaviour of curcumin. Frequently, low doses of toxins and other stressors not only are harmless but also activate an adaptive stress whereas high dose activates acute responses like autophagy and cell death. This phenomenon is referred to as hormesis. Many molecules that cause cell death elicite an initial autophagic step that is a cytoprotective mechanism relying on elimination of dysfunctional structures intracellular, notably by mitophagy. This phenomenon is considered as a primarily protective mechanism against stressors. At higher doses, cells undergo mitochondrial outer membrane permeabilization due to calcium release from the endoplasmic reticulum and die. Herein, we address the complex crosstalk between the induced mitochondrial biogenesis, mitochondrial destabilization accompanied by mitophagy and cell death that can also be at play.

We report a very frugal microscope building method from easily realizable parts. We show a highly portable field ready compound type microscope with bright field, dark field and projection microscopy capabilities. It has good resolution and magnification for multiple aspects of education and diagnosis. We demonstrate that such a system can be built from simple lenses in laser pointers and camera modules with no specific 3d printed parts or costly lenses. We show all the parts of the system like stage, coarse and fine focussing system, microscope body, even slides can be built from commonly available materials like soda bottle and DVD disks. We list alternate, safer and easily available staining methods and chemicals. The microscope is developed with a target that it can be self-developed even in rural areas of the world with only resources at one’s disposal with very little education. This features a stable focussing and panning system for comfortable viewing through eyes and also easy imaging with a smartphone. We show its utility for microorganism analysis and potential for clinical diagnosis.

Cellular substructure has been widely observed in the sample fabricated by selective laser melting, while its growth direction and the crystallographic orientation have seldom been studied. This research tries to build a general model to construct the substructure from its two dimensional morphology. All the three Bunge Euler angles to specify a unique growth direction are determined, and the crystallographic orientation corresponding to the growth direction is also obtained. Based on the crystallographic orientation, the substructure in the single track is distinguished between cell-like dendrite and cell. It is found that, with the increase of scanning velocity, the substructure transits from cell-like dendrite to cell. The critical growth rate of the transition can be around 0.31 ms^-1.

Cancer is a devastating disease with female breast cancer becoming the leading cause of global cancer morbidity. Herein we report the design and synthesis of a sorafenib analog 1A and its base-promoted arranged compound 1A2. Their in vitro cytotoxicity and potencies in EFGR inhibition study revealed that compound 1A displayed good antiproliferative activity in MDA-MB-231 (breast) cells with an IC50 value of 16.18±1.42 μM. Crystallization 1A2 affored 1A2a as a solvate with dichloromethane which was explicitly confirmed by the single crystal X-ray diffraction analysis.

This study attempts to classify compound words on the basis of Cognitive Linguistics and compares their usage trends using Computational Linguistics. Using Noam Chomsky’s concept of deep and surface structures of a sentence, Lees treated compound words, not as separate units but as a kind of embedded sentences and hinted for possible presence of deep and surface structures in compound words, which this study tries to investigate. Then on the basis of the Idealized Cognitive Model proposed by Lakoff and Fauconnier, compound words have been classified into transparent, opaque and counterintuitive compound words. Using Google Books Corpus, this study also compares their usage trends. This is done using usage frequency, defined in this work, which is analogous to productivity for affixed words calculated by G.E.Booij. Each class of compound word formed on the basis of ICM is found to have different usage frequency. The possible reasons for this are discussed.

The separation of sister chromatids during anaphase is the culmination of mitosis and one of the most strikingly beautiful examples of cellular movement. It consists of two distinct processes: Anaphase A, the movement of chromosomes toward spindle poles via shortening of the connecting fibers, and anaphase B, separation of the two poles from one another via spindle elongation. I focus here on anaphase A chromosome-to-pole movement. The chapter begins by summarizing classical observations of chromosome movements, which support the current understanding of anaphase mechanisms. Live cell fluorescence microscopy studies showed that poleward chromosome movement is associated with disassembly, or ‘melting’ of the kinetochore-attached microtubule fibers that link chromosomes to poles. Microtubule-marking techniques established that kinetochore-fiber disassembly often occurs through a ‘pac-man’ mechanism, where tubulin subunits are lost from kinetochore-attached plus ends and the kinetochore appears to consume its microtubule track as it moves poleward. In addition, kinetochore-fiber disassembly in many cells occurs partly through ‘flux’, where the microtubules flow continuously toward the poles and tubulin subunits are lost from minus ends. Molecular mechanistic models for how load-bearing attachments are maintained to disassembling microtubule ends, and how the forces are generated to drive pac-man and flux-based movements, are discussed.

The article continues the search for a general law that describes the physical properties of a solid body, represented as a complex compound, through the physical properties of its elements. For a set of mixtures of metal oxides (actinide oxides), their melting or solidification temperatures were described in terms of the atomic weighted sum of the melting/solidification temperatures of these metals and molecular oxygen, multiplied by a variable which depending on the crystal structure and properties of melt of the compound and on the atomic numbers of the elements that make up the compound.

Objectives: One of the home-made herbal remedy being traditionally used against gout is evaluated to identify any new and characteristic marker compound which may be used as characteristic analytical marker to standardize this polyherbal remedy. Materials and method: A distinct and remarkable peak in the HPLC chromatogram of remedy was identified which was further isolated by fraction collector. This fraction was then evaporated and characterized for structure elucidation using set of various techniques such as RP-HPLC,UV, FTIR, TLC, EIMS and NMR. Results: The compound characterized was non polar compound, ester of betulin and palmitoleic acid. Although the remedy has been standardized using set of four markers as discussed in literature but this newly developed marker compound can be used to further standardize this remedy and other herbal preparations comprising of this marker compound.Conclusion: Hence the isolated compound can be used as novel analytical marker in the standardization of this herbal remedy and the other herbal preparations containing such marker compound

This work is the first scientific study on the development of the composition and technology of a new antioxidant agent based on a combination of extracts of tree medicinal plants and the study of the technological parameters of a dry extract. Further draw up technological regulations for their production and their introduction into production. This study aims to the antioxidant activity of dry extract "Antioxim" was determined. In order to create this herbal collection of plant, first of all, to study the technological parameters of raw materials, such as mass size, porosity, dispersibility, free volume of layers of raw materials, water absorption coefficient of extractives, and technological process efficiency to study the effect of parameters, developed at the Department of "Industrial Technology of Medicines" of the Tashkent Pharmaceutical Institute:

Compound databases of natural products have a major impact on drug discovery projects and other areas of research. The number of databases in the public domain with compounds from natural origin is increasing. Several countries have initiatives in place to construct and maintain compound databases that are representative of their diversity. Examples are Brazil, France, Panama and recently Vietnam. Herein, we discuss the first version of BIOFACQUIM, a novel compound database with natural products isolated and characterized in Mexico. We discuss its construction, curation, and a complete chemoinformatic characterization of the content and coverage in chemical space. It is reported the profile of physicochemical properties, scaffold content, and diversity, as well as structural diversity based on molecular fingerprints. BIOFACQUIM is freely available.

There is a fast-growing interest in the use of selective laser melting (SLM) for metal/alloy additive manufacturing. Our current knowledge of SLM printed 316 stainless steel (SS316) is limited and sometimes appears sporadic, presumably due to the complex interdependent effects of a large number of process variables of the SLM processing. This is reflected from the discrepant findings in the crystallographic textures and microstructures in this investigation with those reported in the literatures, which also vary itself. The as-printed material is macroscopically asymmetric in both the structures and crystallographic textures. The <101> and <111> crystallographic directions align parallel with the SLM scanning direction (SD) and build direction (BD), respectively. Like-wise, some characteristic low angle boundary features are reported crystallographic, while this investigation unequivocally proves them non-crystallographic since they always maintain an identical alignment with the SLM laser scanning direction irrespective of the matrix material’s crystal orientation. There is also 500±200 nm columnar or cellular features, depending on the cross-section, generally found all over the sample. These columnar or cellular features are formed with walls made of dense packing of dislocations entangled with Mn, Si and O enriched amorphous inclusions. They remain stable after the ASM solution treatments at 1050 °C temperatures, and therefore, are capable of hindering boundary migration events of recrystallization and grain growth. Thus, the nanoscale structures can be retained at high temperatures. Large 2-4 µm inclusions form during the solution treatment, within which the chemical and phase distribution are heterogeneous.

Temperature field is an essential attribute of metal additive manufacturing in view of its bearings on the prediction, control, and optimization of residual stress, part distortion, fatigue, balling effect, etc. This work provides an analytical physics-based approach to investigate the effect of scan strategy parameters including time delay between two irradiations and hatching space on thermal material properties and melt pool geometry. This approach is performed through the analysis of the distribution of material properties and temperature profile in three-dimensional space. The moving point heat source approach is used to predict the temperature field. To predict the temperature field during the additive manufacturing process some important phenomena are considered. 1) Due to the high magnitude of temperature in the presence of the laser, the temperature gradient is usually high which has a crucial influence on thermal material properties. Consequently, the thermal material properties of stainless steel grade 316L are considered to be temperature-dependent. 2) Due to the repeated heating and cooling, part usually undergoes several melting and solidification cycles. This physical phenomenon is considered by modifying the heat capacity using the latent heat of melting. 3) The multi-layer aspect of metal AM process is considered by incorporating the temperature history from the previous layer since the interaction of the successive layers has an impact on heat transfer mechanisms. 4) Effect of heat affected zone on thermal material properties is considered by the superposition of material properties in regions where the temperature fields of two consecutive irradiations have an overlap since the consecutive irradiations change the behavior of the material properties. The goals are to 1) investigate the effects of temperature-sensitive material properties and constant material properties on the temperature field. 2) Study the behavior of thermal material properties under different scan strategies. 3) Study the importance of considering the effect of heat affected zone on thermal material through the prediction of melt pool geometry. 4) Investigate the effect of hatching space on melt pool geometry. This work is purely employed physics-based analytical models to predict the behavior of material properties and temperature field under different process conditions, and no finite element modeling is used.

Vit-106 is a promising zirconium-based alloy with high glass-forming ability and belongs to the so-called bulk metallic glasses (BMG). Workpieces with a size of around one centimeter in all three dimensions can be obtained from a BMG alloy by casting. However, further increasing the cast size decreases the cooling rate and thus induces crystallization. Selective laser melting (SLM) is a well-known technique to overcome the size limitations for BMGs because a workpiece is built by the addition of multiple melt portions where the cooling rate is kept above the critical one. Currently, BMG parts obtained by SLM suffer from partial crystallization. The present work studies the influence of SLM process parameters on partial crystallization of Vit-106 by metallography and the influence of the microstructure on mechanical properties by microhardness and wear resistance testing. Submicron crystalline inclusions are observed in an amorphous matrix of Vit-106 alloy obtained by SLM. The size and the concentration of the inclusions can be controlled by varying the laser scanning speed. It is shown that submicron crystalline inclusions formed in the amorphous matrix during SLM can favorably affect microhardness and wear resistance.

The energy transfer process of laser selective melting is very complex. To study the effect of la-ser selective melting on the microstructure and properties of 18Ni-300 martensitic steel, ABAQUS was used to simulate the temperature of laser cladding 18Ni-300 martensitic steel at different time points and different laser power. The results show that the cross-section shape of the molten pool changes from round to oval With the increase of laser power, the higher the peak value of temperature time curve, the greater the temperature gradient; and the laser clad-ding experiment of 18Ni-300 martensitic steel was carried out, and the microstructure and me-chanical properties of the samples under different laser power were analyzed. The results show that with the increase of laser power, the grain size of the cladding layer becomes smaller and the microstructure becomes more compact; the hardness of the side surface of the sample is higher than that of the upper surface, and the tensile strength and elongation show a trend of first increasing and then decreasing.

Although the concept of additive manufacturing has been proposed for several decades, momentum of selective laser melting (SLM) is finally starting to build. In SLM, density and surface roughness, as the important quality indexes of SLMed parts, are dependent on the processing parameters. However, there are few studies on their collaborative optimization in SLM to obtain high relative density and low surface roughness simultaneously in the previous literature. In this work, the response surface method was adopted to study the influences of different processing parameters (laser power, scanning speed and hatch space) on density and surface roughness of 316L stainless steel parts fabricated by SLM. The statistical relationship model between processing parameters and manufacturing quality is established. A multi-objective collaborative optimization strategy considering both density and surface roughness is proposed. The experimental results show that the main effects of processing parameters on the density and surface roughness are similar. It is noted that the effects of the laser power and scanning speed on the above objective quality show highly significant, while hatch space behaves an insignificant impact. Based on the above optimization, 316L stainless steel parts with excellent surface roughness and relative density can be obtained by SLM with optimized processing parameters.

The high entropy alloy (HEA) of equiatomic composition CrNiFeCoMn and with FCC crystal structure was additively manufactured with a selective laser melting (SLM) process starting from mechanically alloyed powders. The as produced alloy shows finenitride and  phase pre-cipitates, which are Cr-rich and stable up to about 900 K. The precipitates increase in number and dimensions after long-period annealing at 900-1300 K, with a change in the HEA mechanical properties. Higher aging temperatures in furnace, above 1300 K, turn the alloy in a single FCC structure, with disappearance of the nitrate and  phase precipitates inside the grains and at the grain boundaries, but with still a presence of a finer Cr-rich nitride precipitation phase. These re-sults suggest that the as-produced HEA is a supersatured solid solution at low and intermediate temperature with nitrides and  nanostructures.

Risk-averse areas such as the medical, aerospace and energy sectors have been somewhat slow towards accepting and applying Additive Manufacturing (AM) in many of their value chains. This is partly because there are still signi cant uncertainties concerning the quality of AM builds. This paper introduces a machine learning algorithm for the automatic detection of faults in AM products. The approach is semi-supervised in that, during training, it is able to use data from both builds where the resulting components were certi ed and builds where the quality of the resulting components is unknown. This makes the approach cost ecient, particularly in scenarios where part certi cation is costly and time consuming. The study speci cally analyses Selective Laser Melting (SLM) builds. Key features are extracted from large sets of photodiode data, obtained during the building of 49 tensile test bars. Ultimate tensile strength (UTS) tests were then used to categorise each bar as `faulty' or `acceptable'. A fully supervised approach identi ed faulty specimens with a 77% success rate while the semi-supervised approach was able to consistently achieve similar results, despite being trained on a fraction of the available certi cation data. The results show that semi-supervised learning is a promising approach for the automatic certi cation of AM builds that can be implemented at a fraction of the cost currently required.

This study characterizes the microstructure and its associated crystallographic features of bulk maraging steels fabricated by selective laser melting (SLM) combined with a powder bed technique. The fabricated sample exhibited characteristic melt pools in which the regions had locally melted and rapidly solidified. A major part of these melt pools corresponded with the ferrite (alpha) matrix, which exhibited a lath martensite structure with a high density of dislocations. A number of fine retained austenite (gamma) with a <001> orientation along the build direction was often localized around the melt pool boundaries. The orientation relationship of these fine gamma grains with respect to the adjacent alpha grains in the martensite structure was (111) gamma // (011) alpha and [-101] gamma // [-1-11] apha (Kurdjumov–Sachs orientation relationship). Using the obtained results, we inferred the microstructure development of maraging steels during the SLM process. The results depict that new and diverse high-strength materials can be used to develop industrial molds and dies.

Molybdenum tailings powder (MTs) is an industrial waste that contains more than 85% contents of SiO2, Al2O3, CaO, and Fe2O3. Therefore, MTs has the potential pozzolanic activity and can be used as a mineral admixture in cementitious materials. In order to understand the influence of MTs as an admixture on the cement hydration process, the hydration heat and hydration kinetics of the composite cementitious materials (CCMs) were investigated by an isothermal calorimeter and the Krstulovic-Dabic model. Furthermore, the influences of fly ash (FA), slag (SL) and MTs on hydration heat at the same content were compared and analyzed. Results show that proper amount of MTs can promote the hydration of CCMs. When the content of MTs is not more than 15%, the second exothermic peak of CCMs appears earlier and the peak heat release increases. However, when the content of MTs exceeds 15%, the second exothermic peak of CCMs is delayed and the peak heat release decreases. The cumulative heat release of CCMs gradually decreases with an increasing content of MTs. When the replacement of MTs, FA, and SL is 15% respectively, the addition of MTs enhances the second exothermic peak of CCMs compared to FA and SL. The final heat release of MTs is higher than that of FA, but lower than that of SL. The hydration process of CCMs undergoes three stages: nucleation and crystal growth (NG), interactions at phase boundaries (I), and diffusion (D). The incorporation of MTs shortens the NG stage and I stage.

Multicore magnetic nanoparticles of manganese ferrite were prepared using carboxymethyl-dextran and melamine as agglutinating agents. The nanoparticles prepared using melamine exhibit a flower-shape structure, a saturation magnetization of 6.16 emu/g and good capabilities for magnetic hyperthermia. Magnetoliposome-like structures containing the multicore nanoparticles exhibit sizes in the range 250 – 400 nm. A new antitumor thienopyridine derivative was loaded in these nanocarriers with a high encapsulation efficiency of 98% ± 2.6%. Release profiles in absence and presence of an AMF indicate a transport by diffusion, with a maximum compound release of 31% under the AMF. A sustained and controlled drug release in anticipated from the results, pointing to suitable characteristics of the magnetoliposomes for dual cancer therapy (combined magnetic hyperthermia and chemotherapy).

To realize the diagnosis of compound faults in gearboxes at different speeds, an "end-to-end" intelligent diagnosis method based on a deep neural network is proposed, named efficiency channel attention-capsule network (ECA-CN). First, the process uses a deep convolutional neural network to extract fault features from the collected raw vibration signals, then embeds the efficient channel attention module to filter important fault features, then uses the capsule network to vectorize the feature space information, and finally calculates the correlation between different levels of capsules by the dynamic routing algorithm to achieve accurate gearbox compound fault diagnosis. The effectiveness of the proposed ECA-CN fault diagnosis method was verified by the composite fault dataset of the 2009 PHM Challenge gearbox, with an average accuracy of 99.63% and a standard deviation of 0.22%. In the comparison experiments with the traditional fault diagnosis method, the average accuracy of the ECA-CN method was improved by 4.62%, and the standard deviation was reduced by 0.58%. The experimental results show that ECA-CN has a more competitive diagnostic performance.

The natural compounds of boron have many applications, including as dietary supplement. Communication is based on the discovery that diester chlorogenoborate complex can be detected and quantified from green coffee bean. The study reports that such diester molecule can also be synthesized in stable form by direct reaction of boric acid and chlorogenic acid, in a mixture of acetonitrile–water (1:1, v/v), left to evaporate over a period of 48 hours, at room temperature, resulting a spirocyclic form (diester complex). The diester complex, with its molecular structure and digestibility attributes has potential application as prebiotic in gut health, oral health and as micronutrient essential for microbiota to human and animals.

This paper presents a two-dimensional mathematical model of compound eye vision. Such a model is useful for solving navigation issues for autonomous mobile robots on the ground plane. The model is inspired by the insect compound eye that consists of ommatidia, which are tiny independent photoreception units, each of which combines a cornea, lens, and rhabdom. The model describes the planar binocular compound eye vision, focusing on measuring distance and azimuth to a circular feature with an arbitrary size. The model provides a necessary and sufficient condition for the visibility of a circular feature by each ommatidium. On this basis, an algorithm is built for generating a training data set to create two deep neural networks (DNN): the first detects the distance, and the second detects the azimuth to a circular feature. The hyperparameter tuning and the configurations of both networks are described. Experimental results showed that the proposed method could effectively and accurately detect the distance and azimuth to objects.

Based on the prosed criterion of the type of heating, a classification of the sources of pulsed electron beams was carried out, for better understanding both the nature of the thermal processes occurring under irradiation and for predicting their suitability for certain applications. The melting thresholds of materials were calculated over the wide ranges of accelerating voltages and pulse durations. On the basis of calculations, a refractoriness series of metals for surface-volume pulsed heating was proposed.

Most of the commonly used Ionic Liquids (ILs) contain bulky organic cations with suitable anions. With our COMPLET (Concept of Melting Point Lowering due to Ethoxylation), we follow a different approach. We use simple, low-toxic, cheap and commercially available anions of the type Cx(EO)yCH2COO– to liquefy presumably any simple metal ion, independently of its charge. In the simplest case, the cation can be sodium or lithium, but synthesis of Ionic Liquids is also possible with cations of higher valences such as transition or rare earth metals. Anions with longer alkyl chains are surface active and form surface active ionic liquids (SAILs), which combine properties of ionic and nonionic surfactants at room temperature. They show significant structuring even in their pure state, i.e. in the absence of water or any other added solvent.

The paper deals with the Compound Inverse Rayleigh distribution, shown to constitute a proper model for the characterization of the probability distribution of extreme values of wind-speed, a topic which is gaining growing interest in the field of renewable generation assessment, both in view of wind power production evaluation and the wind-tower mechanical reliability and safety. The first part of the paper illustrates such model starting from its origin as a generalization of the Inverse Rayleigh model - already proven to be a valid model for extreme wind-speeds - by means of a continuous mixture generated by a Gamma distribution on the scale parameter, which gives rise to its name. Moreover, its validity to interpret different field data is illustrated, also by means of numerous numerical examples based upon real wind speed measurements. Then, a novel Bayes approach for the estimation of such extreme wind-speed model is proposed. The method relies upon the assessment of prior information in a practical way, that should be easily available to system engineers. In practice, the method allows to express one’s prior beliefs both in terms of parameters, as customary, and/or in terms of probabilities. The results of a large set of numerical simulations – using typical values of wind-speed parameters - are reported to illustrate the efficiency and the accuracy of the proposed method. The validity of the approach is also verified in terms of its robustness with respect to significant differences compared to the assumed prior information.

The utilization of selective laser melting (SLM) for high entropy alloys (HEAs) holds significant promise in commercial applications, and substantial experimental research efforts have been directed toward this domain. To take advantage of the reported experimental data of SLM manufactured (SLM-ed) HEAs and reduce unnecessary experimentation, this study incorporates machine learning (ML) techniques for the phase and tensile properties prediction of SLM-ed HEAs, thus presenting a novel avenue for accelerating the discovery of new SLM-ed HEAs. Through the adjustment of material descriptors and machine learning models, a model has been developed with an impressive accuracy of 93.8% in distinguishing between face-centered cubic (FCC), body-centered cubic (BCC), and dual-phase (FCC+BCC). Additionally, optimized models have been devised for the prediction of tensile properties, namely ultimate tensile strength (UTS), yield strength (YS), and elongation (δ), achieving noteworthy MAPEs (mean absolute percentage errors) of 10.33%, 8.55%, and 28.48%, respectively. Furthermore, several HEAs were fabricated using SLM, and the experimental outcomes exhibited a favorable alignment with the predicted results. These efforts carry significant implications in advancing the utilization of SLM for HEAs.

Research on the development of new lightweight Al-Li alloys using selective laser melting pro-cess has great potential for industrial applications. This paper reports on the development of novel aluminum-lithium alloys using selective laser melting technology. Al-Cu-Li-Mg-Ag-Sc-Zr pre-alloyed powders with lithium contents of 1 wt.%, 2 wt.% and 3 wt.%, respectively, were prepared by inert gas atomization. After SLM process optimization, the microstructure and me-chanical properties of the as-formed specimens were investigated. The densification of the three newly developed alloys are 99.51 %, 98.96 % and 92.01 %, respectively. They all have good form-ability, with the lithium loss rate about 15 %. The as-formed alloy with 1% Li content presents good comprehensive properties with a yield strength of 412.6 ± 16.0 MPa, an ultimate tensile strength of 461.1 ± 11.7 MPa, and an elongation of 13.6 ± 1.1%. The three alloys exhibit a layered molten pool stacking morphology and have a typical heterostructure. The columnar crystals and equiaxed fine grains are alternately arranged, and most of the precipitated phases are enriched at the grain boundaries. The change of Li content mainly affects the precipitation of Cu-containing phase. When the Li content is 1 wt.%, there are θ phase, T1 phase and TB phase. When Li increased to 2 wt.%, T1 and T2 phases precipitated together. When Li reaches 3 wt.%, δ' phase precipitates with T2 phase. This study provides useful guidance for the future SLM form-ing of new crack-free and high-strength Al-Li alloys.

Electron Beam Melting (EBM) is an increasingly used Additive Manufacturing (AM) technique employed by many industrial sectors, including the medical device and aerospace industries. The application of this technology is, however, challenged by the lack of process monitoring and control system that underpins process repeatability and part quality reproducibility. An electronic imaging system prototype has been developed to serve as an EBM monitoring technique, the capabilities of which have been verified at room temperature and at 320+10°C. Nevertheless, in order to fully assess the applicability of this technique, the image quality needs to be investigated at a range of elevated temperatures to fully understand the influence of thermal noise due to heat. In this paper, electronic imaging pilot trials at elevated temperatures, ranging from room temperature to , were carried out. Image quality measure Q of the digital electron images was evaluated, and the influence of temperature was investigated. In this study, raw electronic images generated at higher temperatures had greater Q values, i.e. better global image quality. It has been demonstrated that, for temperatures between , the influence of temperature on electronic image quality was not adversely affecting the visual clarity of image features. It is envisaged that the prototype has significant potential to contribute to in-process EBM monitoring in many manufacturing sectors.

Human cytomegalovirus (HCMV) is a ubiquitous herpesvirus, for which there is no vaccine or cure. This viral infection, once acquired, is life-long, residing latently in hematopoietic cells. However, latently infected individuals with weakened immune systems often undergo HCMV reactivation, which can cause serious complications in immunosuppressed and immunocompromised patients. Current anti-viral therapies target late stages of viral replication, and are often met with therapeutic resistance, necessitating the development of novel therapeutics. In this current study, we identified a naturally occurring flavonoid compound, deguelin, which inhibits HCMV lytic replication. Our findings reveal that nanomolar concentrations of deguelin significantly suppress the production of infectious virus. Further, we show that deguelin inhibits the lytic cycle during the phase of the replication cycle consistent with early (E) gene and protein expression. Importantly, our data reveal that deguelin inhibits replication of a ganciclovir-resistant strain of HCMV. Together, our findings identify a novel, naturally occurring compound that may prove useful in the treatment of HCMV replication.

The utilization of tempered blast furnace (BF) slag through the direct fiber forming process to create high-value thermal insulation materials offers a dual benefit: it efficiently harnesses the latent heat within unused slag and substantially enhances the value of blast-furnace slag utilization. However, gauging the melting properties of iron slag under high temperatures is a challenge. In this study, we explore the melting behavior of SiO2 within a high-temperature molten pool. We employ dynamic visual data (video stream) captured via a non-contact charge coupled device (CCD) video recording system to extract SiO2 contours through image processing. The change in image centroid characteristics is used to establish a convolution function relationship, and MATLAB's traversal search algorithm determines SiO2's centroid position. Given that SiO2 is proportionate to crucible pixels, the area of SiO2 is calculated through pixel statistics within these contours. Subsequently, we propose a new indirect method to process image information, yielding SiO2 volume and mass at different time points. An exponential fitting yields the melting rate function of SiO2. Finally, we compare this indirect method with shape from shading (SFS), quantitative characterization, and dimensional analysis techniques. We also discuss the strengths and limitations of each method. Our findings reveal that the indirect solution method presented here boasts straightforward calculation steps and imposes minimal image format requirements. This research provides theoretical and technical support for blast-furnace slag's direct fiber forming process.

Knowledge of the temperature evolution is crucial to understand and control laser beam welding of low-melting materials. Existing temperature determination approaches are restricted to i) one-dimensional temperature information (e.g. ratio-pyrometers), ii) a priori knowledge of the emissivity (e.g. thermography) and iii) high temperature regions (e.g. two-wavelength imaging). In this paper, a ratio-based two-color-thermography approach is developed that allows for two-dimensional temperature determination in low-melting temperature ranges (< 1200 K). For static measurement situations it is demonstrated, that temperature can be determined despite variation in signal intensity and emissivity with high accuracy. The two-color-thermography set-up is further transferred into a commercial laser beam welding machine and experiments are conducted for varying process parameters. The direct application of the developed two-color-thermography system in dynamic process situations is limited as image artifacts presumably caused by internal reflections inside the optical beam path are present.

Rare ginsenoside compound K (CK), is an intestinal microbial metabolite with a low natural abundance that is primarily produced by physicochemical processing, side chain modification, or metabolic transformation in the gut. Moreover, CK exhibits potent biological activity compared to primary ginsenosides, which has raised concerns in the field of ginseng research and development as well as ginsenosides-related dietary supplements and natural products. Ginsenosides Rb1, Rb2, and Rc are generally used as a substrate to generate CK via several bio-conversion processes. Current research shows that CK has a wide range of pharmacological actions including boosting osteogenesis, lipid and glucose metabolism, lipid oxidation, insulin resistance, anti-inflammatory, and anti-apoptosis properties. Further research on the bioavailability and toxicology of CK can advance its medicinal application. The purpose of this review is to lay the groundwork for future clinical studies and the development of CK as a therapy for metabolic disorders. Furthermore, the toxicology and pharmacology of CK are investigated as well in this review. The findings indicate that CK primarily modulates signal-ing pathways associated with AMPK, SIRT1, PPARs, WNTs, and NF-kB. It also demonstrates a positive therapeutic effect of CK on nonalcoholic fatty liver disease, obesity, hyperlipidemia, diabetes, and its complications, as well as osteoporosis. Additionally, the analogues of CK showed more bioavailability, less toxicity, and more efficacy against disease states. Enhancing bioavailability and regulating hazardous variables are crucial for its use in clinical trials.

Background: The effect of rice bran arabinoxylan compound (RBAC), a plant-based immunomodulator, on the quality of life (QoL) in cancer patients and underlying physiological pathways remains unclear. Trial design: The RBAC-QoL study is a double-blind, randomised, controlled pilot feasibility study. The aim is to determine RBAC’s effects on QoL and the associated action mechanisms. Primary outcomes are the EORTC QLQ-C30 functional, symptom, and global QoL scores with inflammatory, nutritional, and cytokine parameters as secondary and exploratory outcomes. Methods: Recruitment targets adults diagnosed with solid organ tumours (≥ stage II) undergoing active treatment in several outpatient centres in New South Wales, Australia. Interventions are RBAC or matched placebo at 3g/day for 24 weeks allocated through stratified randomisation with participants, oncologists, and data collectors blinded. Data is collected from five study visits six weeks apart. The trial is ongoing. An interim intention-to-treat analysis was performed using repeated measure ANOVA with pairwise comparisons where statistical significance is observed and adjusted with covariates. Results: Global QoL scores from currently available data (n = 16; RBAC = 7, placebo = 9) were statistically different between groups (F[1,8] = 8.6, p = 0.019, eta2[g] = 0.267). Pairwise comparisons found significant differences at week 6 (p = 0.032, Cohen’s d = 1.454) and marginally at week 12 (p = 0.069, d = 1.427). Age-adjusted analysis showed a continuous upward trend in QoL improvement over time with RBAC, while the placebo group did not deviate from baseline QoL. Significant elevations of serum white blood cell count (week 18) and total protein (weeks 12 and 18) were detected in the RBAC group compared to placebo. The total protein levels correlated highly with white blood cell count (Pearson’s r = 0.539, p < 0.001) and moderately with the global QoL scores (r = 0.338, p = 0.01). No intervention-related adverse events were reported in both groups. Conclusions: RBAC improves QoL beyond placebo during active cancer treatment, possibly through the immuno-nutritional pathway. These findings are preliminary but valuable for future research. Funding and registration: Daiwa Pharmaceutical Co., Ltd, Japan; BioMedica Nutraceuticals Pty Ltd., Australia. ANZCTR Reg No: ACTRN12619000562178p.

In the present study, a nanostructured FeAl coating was prepared by cold spraying of ball milled powder. Annealing treatment was applied to the coating to investigate its effect on the microstructure, phase structure and microhardness of the cold-sprayed nanostructured FeAl coating. The results showed that the FeAl phase was kept unchangeable when the coating annealed at the temperature above 500oC. Annealing temperature significantly influenced the microstructure and microhardness of cold-sprayed FeAl coating. With raising annealing temperature, the lamellar structure in the as-sprayed coating disappeared and a dense coating microstructure with fully bonding of deposited particles at their interfaces was achieved after annealing at 950oC. Nanograin growth of the FeAl phase occurred at an annealing temperature higher than 800oC. The microhardness of cold-sprayed FeAl coating remained about 400 Hv0.1 at the annealing temperature below 800oC and decreased to 300 Hv0.1 at 1100oC.

The problem of effective immobilization of liquid radioactive waste (LRW) is key to the successful development of nuclear energy. The possibility of using magnesium potassium phosphate (MKP) compound for LRW immobilization on the example of nitric acid solutions containing actinides and rare earth elements (REE), including high level waste (HLW) surrogate solution is considered in the research work. Under the study of phase composition and structure of the MKP compounds obtained by the XRD and SEM methods, it was established that the compounds are composed of crystalline phases - analogues of natural phosphate minerals (struvite, metaankoleite). The hydrolytic stability of the compounds was determined according to the semi-dynamic test GOST R 52126-2003. Low leaching rates of radionuclides from the compound are established, including a differential leaching rate of ²³⁹Pu and ²⁴¹Am - 3.5 × 10^-7 and 5.3 × 10^-7 g/(cm²∙day). As a result of the research work it was concluded that the MKP compound is promising for LRW immobilization and can become an alternative material combining the advantages of easy implementation of the technology like cementation and the high physical and chemical stability corresponding to a glass-like compound.

Melting, solidification and viscosity properties of a multicomponent Fe-Cu-Nb-Mo-Si-B alloys with low aluminum addition up to 0.42 at.% Al were studied using an oscillating cup viscometer. It is shown that melting and solidification are divided into two stages with a knee point at 1461 K. The temperature dependences of the liquid fraction between the liquidus and solidus temperatures during melting and solidification are calculated. It has been proven that aluminum accelerates the processes of melting and solidification and leads to an increase in liquidus and solidus temperatures. In the liquid state at temperatures above 1700 K in an alloy with a low aluminum content, the activation energy of viscous flow increases. This growth was associated with the liquid – liquid structure transition caused by the formation of large clusters based on the metastable Fe23B6 phase. Aluminum atoms attract iron and boron atoms and contribute to the formation of clusters based on the Fe2AlB2 phase and metastable phases of a higher order.

A Chinese superalloy GH4099 (~20 vol.% γ' phase), which can operate for long periods of time at temperatures of 1173-1273 K, was fabricated by electron beam melting (EBM). Argon gas atomized (AA) and plasma rotation electrode process (PREP) powders with the similar composition and size distribution were used as raw materials for comparison. Microstructure and mechanical properties of both the as-EBMed and post-treated alloy samples were investigated. The results show that the different powder characteristics resulted in the different build temperatures for AA and PREP samples, which were 1253 K and 1373 K, respectively. With increasing the building temperature, the EBM processing window shifted towards the higher scanning speed direction. Furthermore, intergranular cracking was observed for the as-fabricated PREP sample as a result of local enrichment of Si at grain boundaries. The cracks were completely eliminated by hot isostatic pressing (HIPing) and did not re-open during subsequent solution treatment and aging (STA). Fine spherical γ' phase precipitated uniformly after STA. The tensile strength of the HIP+STA samples was ~920 MPa in the building direction and ~850 MPa in the horizontal direction, comparable with that of the wrought alloy.

Additive manufacturing (AM) offers customization of microstructure and mechanical properties of fabricated components according to the material selected, and process parameters applied. Selective laser melting (SLM) is the commonly used technique for processing high strength aluminum alloys. Selection of SLM process parameters could control the microstructure of parts and their mechanical properties. However, the process parameters limit and defects obtained inside the as-built parts present obstacles to customized part production. This study investigates the influence of SLM process parameters on the quality of as-built Al6061 and AlSi10Mg parts according to the mutual connection between the microstructure characteristics and mechanical properties. The microstructure of both materials was characterized for different parts processed over a wide range of SLM process parameters. The optimized SLM parameters were investigated to eliminate the internal microstructure defects. The behaviour of mechanical properties of parts was presented through regression models generated from the design of experiment (DOE) analysis for the results of hardness, ultimate tensile strength, and yield strength. A comparison between the results obtained and that reported in the literature is presented to illustrate the influence of process parameters, build environment, and powder characteristics on the quality of parts produced. The results obtained from this study could help to customize the part’s quality by satisfying their design requirements in addition to reducing the as-built defects which in turn reduce the amount of the post-processing needed.

The development of the additive manufacturing (AM) technology proffers challenging requirements for forming accuracy and efficiency. In this paper, a hybrid additive manufacturing technology combining fusion-based selective laser melting (SLM) and solid-state cold spraying (CS) was proposed in order to enable the fast production of near-net-shape metal parts. The idea is to fabricate a bulk deposit with a rough contour first via “fast” CS process and then add fine structures and complex features through “slow” SLM. The experimental results show that it is feasible to deposit SLM part onto CS part with good interfacial bonding. However, the CS parts must be subject to heat treatment to improve their cohesion strength before being sending for SLM processing. Otherwise, the high tensile residual stress generated during SLM process will cause fracture and cracks in the CS part. After heat treatment, pure copper deposited by CS undergoes grain growth and recrystallization, resulting in improved cohesive strength and release of the residual stress in the CS parts is released. The tensile test on the SLM/CS interfacial region indicates that the bonding strength increased by 38% from 45±7 MPa to 62±1 MPa after the CS part is subject to heat treatment, and the SLM/CS interfacial bonding strength is higher than the CS parts. This study demonstrates that the proposed hybrid AM process is feasible and promising for manufacturing free-standing SLM-CS components.

Residual stress (RS) is the most challenging problem in metal additive manufacturing (AM) since the build-up of high tensile RS may influence the fatigue life, corrosion resistance, crack initiation, and failure of the additively manufactured components. While tensile RS is inherent in all the AM processes, fast and accurate prediction of stress state within the part is extremely valuable and would result in optimization of the process parameters in achieving a desired RS and control of the build process. This paper proposes a physics-based analytical model to rapidly and accurately predict the RS within the additively manufactured part. In this model, a transient moving point heat source (HS) is utilized to determine the temperature field. Due to the high temperature gradient within the proximity of the melt pool area, material experience high thermal stress. Thermal stress is calculated by combining three sources of stresses known as stresses due to the body forces, normal tension, and hydrostatic stress in a homogeneous semi-infinite medium. The thermal stress determines the RS state within the part. Consequently, by taking the thermal stress history as an input, both the in-plane and out of plane RS distributions are found from incremental plasticity and kinematic hardening behavior of the metal by considering volume conservation in plastic deformation in coupling with the equilibrium and compatibility conditions. In this modeling, material properties are temperature-sensitive since the steep temperature gradient varies the properties significantly. Moreover, the energy needed for the solid-state phase transition is reflected by modifying the specific heat employing the latent heat of fusion. Furthermore, the multi-layer and multi-scan aspects of metal AM are considered by including the temperature history from previous layers and scans. Results from the analytical RS model presented excellent agreement with XRD measurements employed to determine the RS in the Ti-6Al-4V specimens.

Selective laser melting (SLM) is one of the widely used techniques in metallic additive manufacturing, in which high-density laser powder is utilized to selectively melting layers of powders to create geometrically complex parts. Temperature distribution and molten pool geometry directly determine the balling effect, and concentrated balling phenomenon significantly deteriorates surface integrity and mechanical properties of the part. Finite element models have been developed to predict temperature distribution and molten pool geometry, but they were computationally expensive. In this paper, the three-dimensional temperature distributions are predicted by analytical models using point moving heat source and semi-ellipsoidal moving source respectively. The molten pool dimensions under various process conditions are obtained from the three-dimensional temperature predictions and experimentally validated. Ti-6Al-4V alloy is chosen for the investigation. Good agreements between the predictions and the measurements are observed. The presented models are also suitable for other metallic materials in the SLM process.

Extreme climates such as droughts and hot extremes, may result in marked damage to crop yields and threaten regional and global food security. Maize is a major grain crop in Liaoning Province, severely affected by drought and hot events. The objective of this study is to advance an approach to estimate the risk of crop yield reduction under the compound dry-hot events (CDHE) in Liaoning Province. Results show that the ratio of stations experiencing compound dry-hot events during the twelfth leaf and maturity stage tended to increase on the time scale. On a spatial scale, the frequency of compound dry-hot events in central Liaoning Province was relatively low during the whole and various reproductive periods of maize. In addition to the twelfth leaf, western Liaoning Province is prone to compound dry-hot events. The high-risk area for the occurrence of the compound dry-hot events in maize is Chaoyang City, located in the western part of Liaoning Province, and the cities in the low-risk area account for about 64.3% of the total number of cities in Liaoning Province, mainly in the central and northern parts of Liaoning Province. Generally, this study emphasizes focusing on the impacts of compound dry-hot events on agricultural production and provides an index to assess the risk of compound dry-hot events on maize production.

The purpose of this paper is to evaluate the timing of innovative investment in technology product life cycles using a compound binomial option with management flexibility. Considering the business cycles changes in the macroeconomic will affect consumer purchasing power. The focus is how to evaluate the optimal investment strategy and the project value. It was applied to different product stages (three stages including production innovation, manufacture innovation, and operation innovation) and factored to different risks to build a technology innovation strategy model. An aim of this study is the options premium of the best strategy timing for each innovation stage. Its application of the compound binomial options for the manufacture innovation will only be considered after the execution of the production innovation. The same condition is applied to the operation innovation, which will only be considered after the execution of the manufacture innovation. Then, this paper constructs the dynamic investment sequential decision model, assesses the feasibility of an investment strategy, and makes a decision on the appropriate project value and options premium for each stage under the possible change of Gross Domestic Product (GDP). This paper investigates the product life cycle innovation investment topic by using the compound binomial options method and will provide a more flexible strategy decision compared with other trend forecast criteria.

The effect of Zr addition on the melting temperature of the CoCrFeMnNi High Entropy Alloy (HEA), known as the “Cantor’s Alloy”, is investigated, together with its microstructure, mechan-ical properties and thermo-mechanical recrystallization process. The base and Zr-modified al-loys are obtained by vacuum induction melting of mechanically pre-alloyed powders followed by recrystallization. The alloys were characterized by X-ray diffraction, scanning and transmis-sion electron microscopy, thermal analyses, mechanical spectroscopy and indentation measures. The main advantages of Zr addition are: 1) a fast vacuum induction melting (VIM) process; 2) the lower melting temperature, due to Zr eutectics formation with all the Cantor’s alloy elements; 3) the good chemical alloy homogeneity; 4) the mechanical properties improvement of recrystallized grains with a coherent structure. The crystallographic lattice of both alloys resulted to be FCC. Results demonstrate that the Zr-modified HEA presents a higher recrystallization temperature and smaller grain size after recrystallization with respect to the Cantor’s alloy, with precipita-tion of a coherent second phase which enhance the alloy hardness and strength, while maintaining a good tensile ductility.

Ti-6Al-4V (TC4) titanium alloy parts were successfully fabricated by laser melting deposition (LMD)technology in this study. Proper normalizing temperatures were presented in detailed for bulk LMD specimens. Optical microscope, scanning electron microscopy, X-ray diffraction and electronic universal testing machine were used to characterize the microstructures, phase compositions, the tensile properties and hardness of the TC4 alloy parts treated using different normalizing temperature. The experimental results showed that the as-fabricated LMD speceimens microstructures mainly consisted of α-Ti phase with a small amount of β-Ti phase. After normalizing treatment, in the area of α-Ti phase, the recrystallized length and width of α-Ti phase both increased. When normalizing in the (α+β) phase field, the elongated primary α-Ti phase in the as-deposited state was truncated due to the precipitation of β-Ti phase and became a short rod-like primary α-Ti phase. In as-fabricated microstructure, the β-Ti phase was precipitated between different short rod-shaped α-Ti phases distributed as basketweave. After normalizing treatment at 990 for two hours with subsequent air cooling, the TC4 titanium alloy had significant different microstructures from original sample produced by LMD. Moreover, the mismatch of tensile and hardness property was mitigated in this heat treatment. So the normalizing treatment methods and temperature can be qualified as a prospective heat treatment of titanium alloy fabricating by laser melting deposition.

At different heat treatment temperatures, the hardness and flexural strength of M2 high-speed steel selective laser melting (SLM) parts show mixed trends. When the heat treatment temperature is 260°C, the hardness and flexural strength of the M2 high-speed steel SLM part are decreased, but the hardness difference between the upper and lower surfaces of the M2 high-speed steel SLM part is also reduced. When the heat treatment temperature is 560°C, the hardness and flexural strength of the M2 high-speed steel SLM part are almost close to that of the original M2 high-speed steel SLM part, and the performance gradient in the sample is improved, and the overall structure is uniform. When the subsequent heat treatment temperature is 860 °C, the hardness of the SLM parts reaches a minimum, with an average value of 24 HRC. However, the flexural strength exceeds that of the original SLM parts. Moreover, the microstructure of the sample is uniform, which significantly improves the anisotropy of performance.

In the present work freezing and melting characteristics of water seeded with chemically functionalized graphene nano-platelets in a vertical cylindrical capsule was experimentally studied. The volume percentage of functionalized graphene nano-platelets was varied from 0.1% to 0.5% with an interval of 0.1%. The stability of the synthesised samples were carried out by zeta potential distribution. The thermal conductivity of the nanocomposite samples were experimentally measured using transient hot wire method. A maximum enhancement of ~24% in the thermal conductivity was observed for the 0.5% volume percentage in the liquid state while a ~53% enhancement in the solid state. Freezing and melting behaviour of water dispersed with graphene nanoplatelets were carried out using a cylindrical stainless steel capsule in a constant temperature bath. The bath temperatures considered for studying freezing characteristics were considered to be −6 °C and −10 °C, while to study the melting characteristics the bath temperature was set as 31 °C and 36 °C. The freezing and melting time decreased for all the test conditions when the volume percentage of GnP increased. The freezing rate was enhanced by ~ 43% and ~32% for the bath temperatures of −6 °C and −10 °C respectively at 0.5 vol % of graphene loading. The melting rate was enhanced by ~42% and ~63% for the bath temperature of 31 °C and 36 °C respectively at 0.5 vol % of graphene loading.

Electron Beam Melting (EBM) is an increasingly used Additive Manufacturing (AM) technique employed by many industrial sectors, including the medical device and aerospace industries. In EBM process monitoring, data analysis for processed layer quality evaluation is currently focused on the extraction of information from the raw data collected in-EBM process, i.e. thermal/ optical / electronic images, and the comparison between the collected data and the Computed Tomography (CT)/ microscopy images generated post-EBM process. This article postulates that a stack of bitmaps could be generated from the 3D model at a range of Z heights during file preparation of the EBM process, and serve as a reference image set. In-EBM process comparison between that and the workpiece images collected during the EBM process could then be used for quality assessment purposes. In addition, despite the extensive literature on 3D model slicing and contour generation for AM process preparation, no methods regarding image generation from cross sections of the 3D models have been disseminated in details. This article aims to address this by presenting a piece of 3D model-image generation software. The software is capable of generating binary 3D model reference images with user-defined Region-of-Interest (ROI) of the processing area, and Z heights of the model. It is envisaged that this 3D model-reference image generation ability opens up new opportunities in quality assessment for the in-process monitoring of the EBM process.

Scutellaria multicaulis, a member of the Lamiaceae, is a medicinal plant indigenous to Iran, Afghanistan, and Pakistan. It has been widely used as a prominent herb in traditional medicine for thousands of years. This plant is reported with baicalein, wogonin, and chrysin flavonoids as a significant group of chemical ingredients, which can cure different diseases such as breast cancer. S. multicaulis leave extract was used for the bioreduction of silver nanoparticles (SmL-Ag-NPs), and their phytochemical contents and antioxidant, antibacterial, anti-proliferative, and apoptotic activity were evaluated. Optimal physicochemical properties of SmL-Ag-NPs were obtained by mixing 5% of leave extract and 2 mM of aqueous AgNO3 solution and confirmed by characterization studies including UV–visible spectrophotometry, FE-SEM, EDX, DLS, zeta potential, TGA, SERS, XRD and FTIR Spectroscopy. SmL-Ag-NPs exhibited higher content of TPC (Total Phenolic Content) and TFC (Total Flavonoid Content) and potential antioxidant activity. SmL-Ag-NPs also demonstrated dose-dependent cytotoxicity against MDA-MB231 cells multiplication with an IC50 value of 37.62 μg/mL at 48h through inducing cell apoptosis. This is the first report on the biosynthesis of silver nanoparticles using S. multicaulis leave extract, which can provide treatment for cancer diseases and reduce some negative effects of chemotherapy.

The composition of bacteria in the gastrointestinal tract of piglets is easily affected by environmental changes, particularly during the weaning period. Compound strains of Lactobacillus reuteri and Lactobacillus salivarius were supplemented to piglets during pre- and post-weaning to determine their effects in improving the growth performance and ameliorating the diarrhea rate and stress caused by antioxidation in piglets. A larger number of L. reuteri and L. salivarius colonized the distal segment of the ileum and the total numbers of Lactobacillus spp. and Bifidobacterium were higher in the ileal mucous membrane and cecal lumen with probiotics supplementation. The numbers of antioxidative and immune molecules were increased in the plasma following compound bacteria (CL) supplementation, whereas cortisol and endotoxin levels were lower and growth hormone and insulin-like growth factor 1 were higher. Spearman’s and KEGG analysis of the bacterial operational taxonomic unit and antioxidative and immune indices and metabolic genes indicated that the body growth modulation by CL supplementation could be attributed to optimization of the intestinal bacterial composition. Collectively, these results suggest that supplementation with CL could reduce stress and improve the growth performance of piglets during weaning by optimizing the intestinal bacterial composition.

In this study, the effect of increasing exposure time on microstructures, defectiveness, mechanical properties and corrosion behavior of selective laser melted sample Al-Si10-Mg powder have been investigated. The sample were processed at the same power (375 W) and scan speed (2000 mm/s) but with increasing exposure time. Exposure time equal to 40, 50 and 60 µs was applied. The features of the analyzed samples show that with increasing exposure time a better efficiency of the heat input has been obtained with larger size of melting pool and Si particles and lower defectiveness. Moreover, being the coarser microstructure associated a to lower level of voids, the average hardness is similar for the analyzed samples. The potentiodynamic curves of the samples show that the voids occurrence is more significant with respect to the scale of micro-structure on corrosion behavior being the sample processed at the highest exposure time the more resistant to corrosion. The experimental techniques used in the present study were Optical microscope, Sem microscope, Hardness and X-Ray Computed Tomography.

This study introduces an advanced dual-mode composite attitude control framework for reusable launch vehicles (RLVs), underpinned by an enhanced particle swarm optimization (PSO) algorithm. This innovative strategy is tailored to meet the stringent demands for precision and robust anti-interference capabilities across the entire flight envelope of RLVs. The research commences with the formulation of a comprehensive attitude dynamics model and diverse heterogeneous actuator representations, meticulously crafted to reflect the distinct phases of RLV flight. Building upon this foundation, a synergistic control paradigm is engineered, integrating PID and fuzzy PID controllers, complemented by a refined fitness evaluation function. The crux of the study is the application of an upgraded PSO algorithm to fine-tune the controllers' weighting coefficients, culminating in an optimized dual-mode composite attitude control system. A series of comparative simulation analyses are meticulously executed to appraise the system's responsiveness, stability, precision, and resilience to interference. The findings unequivocally substantiate the superior performance of the proposed control system, affirming its substantial contribution to the advancement of RLV attitude control.

Protein synthesis has been a very rich target for developing classes of drugs to control prokaryotic and eukaryotic pathogens. Despite the development of new drug formulations, treating human cutaneous and visceral Leishmaniasis still needs significant improvement due to considerable side effects and low adherence to the usual treatment regimen. In this work, we show that the di-substituted urea-derived compound I-17 is effective in inhibiting the promastigote forms and intracellular amastigotes of the Leishmania (L.) amazonensis and L. infantum species, in addition to exhibiting low macrophage cytotoxicity. We also show a potential immunomodulatory effect of I-17 in infected macrophages, which exhibited increased expression of inducible Nitric Oxide Synthase (NOS2) and Nitric Oxide (NO) production. Our data suggest that I-17 and new derivatives of this compound may be helpful in developing new drugs for treating leishmaniasis.

Smallholder dairying engages around 70 to 80 million rural households who are mostly landless, small and marginal farmers. These farmers face challenges in terms of adoption of balanced feeding practices including inclusion of compound feed in animal feeding. This necessitates to understand the socio-economic factors that are influencing the adoption of compound feed. The study found that 51% of dairying households adopted compound feed in animal feeding. The adopters and non-adopters of compound feed differed (P< 0.01) in terms of land holding, family educational status, breeds owned, membership status in farmer’s collectives, fodder adoption, area under fodder, access to grazing resources, availability of crop residues, milk production and milk marketing opportunities. Furthermore, users and non-users of compound feed had significant difference (P< 0.05) in extension agency contact, mass media contact, attitude towards dairying and gender participation in farming. The logit regression model explained the variance in adoption to 30%. Further it indicated the role of selective socio-economic characters, farming situations, feeding and marketing practices in adoption of compound feed. In specific membership in farmer’s collectives, marketing opportunity, milk production, farm men participation, family education status, grazing resources and attitude towards dairying has greatly influenced the adoption behaviour of compound feed in positive direction. Added, households with high experience, cultivating fodder and having access to crop residues tend to influence the adoption decision negatively. The research observed that farmers tend to use compound feed for increasing productivity in areas of better markets and there exists trade-offs between milk market opportunities, access to cheaper roughages and usage of compound feed.

The interaction between oceanographic, meteorological, and hydrological factors can result in an extreme flooding scenario in the low-lying coastal area, called compound flooding (CF) events. For instance, rainfall and storm surge (or high river discharge) can be driven by the same meteorological, tropical or extra-tropical cyclones, resulting in a CF phenomenon. The trivariate distributional framework can significantly explain compound events' statistical behaviour reducing the associated high-impact flood risk. Resolving heterogenous dependency of the multidimensional CF events by incorporating traditional 3-D symmetric or fully nested Archimedean copula is quite complex. The main challenge is to preserve all lower-level dependencies. An approach based on decomposing the full multivariate density into simple local building blocks via conditional independence called vine or pair-copulas is a much more comprehensive way of approximating the trivariate flood dependence structure. In this study, a parametric vine copula of a drawable (D-vine) structure is introduced in the trivariate modelling of flooding events with 46 years of observations of the west Coast of Canada. This trivariate framework searches dependency by combining the joint impact of annual maximum 24-hr rainfall and the highest storm surge and river discharge observed within the time ±1 day of the highest rainfall event. The D-vine structures are constructed in three alternative ways by permutation of the conditioning variables. The most appropriate D-vine structure is selected using the fitness test statistics and estimating trivariate joint and conditional joint return periods. The investigation confirms that the D-vine copula can effectively define the compound phenomenon's dependency. The failure probability (FP) method is also adopted in assessing the trivariate hydrologic risk. It is observed that hydrologic events defined in the trivariate case produce higher FP than in the bivariate (or univariate) case. It is also concluded that hydrologic risk increases (i) with an increase in the service design life of the hydraulic facilities and (ii) with a decrease in return periods.

Abstract: The quantitative analysis of the chromatographic behavior of basic compounds was performed in silico. The liquid chromatography (LC) data measured with pentyl-, hexenyl-, and octyl-bonded silica gels were analyzed in silico employing model phases. The main retention force was the van der Waals (VW) interaction, and the main desorption force was an electrostatic (ES) interaction. The contribution of hydrogen bonding (HB) was weak compared to that for acidic compounds. The quantitative explanation was achieved utilizing the calculated VW, HB, and ES energy values obtained from a molecular mechanics program. The electron localization was observed at the molecular interaction-site calculated MOPAC program. This fundamental approach was like that of explaining chemical reactions. The difference was electron localization in chromatography or electron transfer in a chemical reaction.

Abstract: Yeast – especially Saccharomyces cerevisiae – have long been a preferred workhorse for the production of numerous recombinant proteins and other metabolites. S. cerevisiae is a noteworthy aroma compound producer, and has also been exploited to produce foreign bioflavour compounds. In the past few years, important strides have been made in unlocking the key elements in the biochemical pathways involved in the production of many aroma compounds. The expression of these biochemical pathways in yeast often involves the manipulation of the host strain to direct the flux towards certain precursors needed for the production of the given aroma compound. This review highlights recent advances in the bioengineering of yeast – including S. cerevisiae – to produce aroma compounds and bioflavours. To capitalise on recent advances in synthetic yeast genomics, this review presents yeast as a significant producer of bioflavours in a fresh context and proposes new directions for combining engineering and biology principles to improve the yield of targeted aroma compounds.

Bacterial infections and resistance to antibiotic drugs represent the highest challenges to public health. The search for new and promising compounds with anti-bacterial activity is a very urgent matter. In order to promote the development of platforms enabling to the discovery of compounds with anti-bacterial activity, Fourier Transformed Mid-Infrared (FT-MIR) spectroscopy associated with the machine learning algorithms were used to predict the impact of compounds extracted from Cynara cardunculus against Escherichia coli cells. According to the plant tissue (seeds, dry and fresh leaves, and flowers) and the solvents (ethanol, methanol, acetone, ethyl acetate, and water), compounds with different compositions concerning, phenol content, antioxidant, and antimicrobial activity were obtained. Principal component analysis of spectra, allowed to discriminate compounds that inhibit the E. coli growth, according to the conventional assay. The supervised classification models enabled the prediction of the compound's impact on the E. coli growth, with the accuracy for the test data: Partial least squares-discriminant analysis of 94%; Support vector machines of 89%; k-Nearest neighbor of 72%; and a Backpropagation network of 100%. According to the promising results, the integration of FT-MIR spectroscopy with machine learning presents a high potential to promote the discovery of new compounds with antibacterial activity, thereby streamlining the drug exploratory process.

Sterile alpha motif domain-containing protein 9 (SAMD9) is a regulatory protein centrally involved in cell proliferation and apoptosis. Mapped to 7p21.1, variants in SAMD9 have been reported in &lt;50 pediatric cases worldwide, typically with early lethality. Germline gain-of-function SAMD9 variants are associated with MIRAGE Syndrome (myelodysplasia, infection, restricted growth, adrenal hypoplasia, genital anomalies, and enteropathy). Spalt like transcription factor 1 (SALL1) is a zinc finger transcriptional repressor located at 16q12.1 where only two transcript variants in SALL1 are known. RUNX2 (6p21.1) encodes a nuclear protein with a Runt DNA-binding domain critical for osteoblastic differentiation, skeletal morphogenesis, and serves as a scaffold for nucleic acids and regulatory factors involved in skeletal gene expression. RUNX2 and SALL1 are thus both ‘master regulators’ of tissue organization and embryo development. Here, we describe exome sequencing and copy number variants in two previously unknown mutations—R824Q in SAMD9, and Q253H in SALL1. A new multiexon 3’ terminal duplication in RUNX2 is also reported. This is the first known phenotype characterization for the intersection of all three variants in a healthy 46,XX adult. Focusing on developmental progress, ultrastructural renal anatomy, and selected reproductive aspects, we describe this unique genotype diagnosed incidentally during Covid-19 illness. Individual disruption in SAMD9, RUNX2, or SALL1 would be expected to give a bleak prognosis. However, the convergence discovered here appears to dampen severe pathology, perhaps by cross-gene silencing of effects normally deleterious when such changes occur alone.

Among all the processing technologies of heat-treatable aluminum alloys like 2219 aluminum alloy, using friction stir welding (FSW) as the joining technology and using electromagnetic forming (EMF) for plastic forming technology both have obvious advantages and successful applications. Therefore, there is a broad prospect for the compound technologies which can be used on the 2219 aluminum alloy to manufacture the large-scale thin-wall parts in the astronautic industry. The microstructure and mechanical properties of 2219 aluminum alloy under the process compounded of FSW, heat treatment, and EMF were investigated by means of tensile test, optical microscope (OM), and scanning electron microscope (SEM). The results show that the reduction of strength, which was caused during the FSW process, can be recovered effectively by the post-welding heat treatment composed of solid solution and aging, while the ductility was still reduced after heat treatment. Under the compound technology of FSW, heat treatment, and EMF, the forming limit of 2219 aluminum alloy decreased distinctly due to the poor ductility of the welding joint. A ribbon-pattern, which was formed due to the banded structure caused by FSW process, was found on the fracture surface of welded 2219 aluminum alloy after EMF treatment. During the EMF process, because of the effects of induced eddy current, a unique structure, which was manifested as a molted-surface appearance under the SEM observation, was formed as the material fractured.

There is high confidence that climate change has increased the probability of concurrent temperature-precipitation extremes, changed their spatial-temporal variations, and affected the relationships between drivers of such natural hazards. However, the extent of such changes has been less investigated in Australia. Daily weather data (131 years, 1889-2019) at 700 grid cells (1◦ × 1◦) across Australia was obtained to calculate annual and seasonal mean daily maximum temperature (MMT) and total precipitation (TPR). A nonparametric multivariate copula framework was adopted to estimate the return period of compound hot-dry (CHD) events based on an ‘And’ hazard scenario (hotter than a threshold ‘And’ drier than a threshold). CHD extremes were defined as years with joint return periods of larger than 25 years. Mann-Kendall nonparametric tests was used to analyse trends in MMT and TPR as well as in the frequency of univariate and CHD extremes. A general cooling-wetting trend was observed over 1889-1989. Significant increasing trends were detected over 1990-2019 in the frequency and severity of hot extremes across the country while trends in dry extremes were mostly insignificant (and decreasing). Results showed a significant increase in the association between temperature and precipitation at various temporal scales. The frequency of CHD extremes was mostly stable over 1889-1989, but significantly increased between 1990 and 2019 at 44% of studied grid cells, mostly located in the north, south-east and south-west. Spatial homogeneity (i.e. connectedness) and propagation of extreme events from one grid cell to its neighbouring cells was investigated across Australia. It can be concluded that this connectedness has not significantly changed since 1889.

Some novel (phenyl-diazenyl)phenols (3a–g) were designed and synthesized to be evaluated for their antimicrobial activity. A previously synthesized molecule, active against bacteria and fungi, was used as lead for modifications and optimization of the structure, by introduction/removal or displacement of hydroxyl groups on the azobenzene rings. The aim of this work was to evaluate the consequent changes of the antimicrobial activity and to validate the hypothesis that, for these compounds, a plausible mechanism could involve an interaction with protein receptors, rather than an interaction with membrane. All newly synthesized compounds were analyzed by ¹H nuclear magnetic resonance (NMR), DSC thermal analysis and UV-Vis spectroscopy. The in vitro minimal inhibitory concentrations (MIC) of each compound was determined against Gram-positive and Gram-negative bacteria and Candida albicans. Compounds 3b and 3g showed the highest activity against S. aureus and C. albicans, with remarkable MIC values of 10 µg/mL and 3 µg/mL, respectively. Structure- activity relationship studies were capable to rationalize the effect of different substitutions on the phenyl ring of the azobenzene on antimicrobial activity.

Mental health in Puerto Rico is a complex and multifaceted issue that has been shaped by the island’s unique history, culture, and political status. Recent challenges, including disasters, economic hardships, and political turmoil, have significantly affected the mental well-being of the population coupled with the limitations in the accessibility of mental health services. Puerto Rico has fewer mental health professionals per capita than any other state or territory in the United States. This comprehensive review examines the impact of disasters on mental health and mental health services in Puerto Rico. Given the exodus of Puerto Ricans from the island, the review also provides an overview of mental health resources available on the island as well as the continental United States. The review identifies efforts to address mental health issues, with the intent of gaining a proper understanding of the available mental health services, key trends, as well as observable challenges and achievements within the mental health landscape of the Puerto Rican population.

Drug hypersensitivity reactions (DHR) to platinum-based compounds (PC) are on the rise, and their personalized and safe management is essential to enable first-line treatment of these cancer patients. This study aimed to evaluate the usefulness of basophil activation test by flow cytometry (BAT-FC) and the newly developed sIgE-microarray and BAT-microarray in diagnosing IgE-mediated hypersensitivity reactions to PC. 24 patients with DHR to PC (20 oxaliplatin and four carboplatin) were evaluated: 13 patients diagnosed as allergic with positive skin tests (STs) or drug provocation tests (DPTs), six patients diagnosed as non-allergic with negative STs and DPTs, and five patients classified as suspected allergic because DPTs could not be performed. In addition, four carboplatin-tolerant patients were included as controls. BAT-FC was positive in 2 of 13 allergic patients, with a sensitivity of 15.4% and specificity of 100%. However, the sIgE- and BAT-microarrays were positive in 11 of 13 DHR patients, giving a sensitivity of over 84.6% and a specificity of 90%. Except for one patient, all samples from the non-allergic and control group were negative for the sIgE- and BAT-microarrays. Our experience indicates that sIgE- and BAT-microarray could be helpful in the endophenotyping of IgE-mediated hypersensitivity reactions to PC and may provide an advance in decision-making for drug provocation testing.

The flower of Syringa pubescens Turcz. is a Chinese folk medicine and also used as flower tea for healthcare. The effects of five drying methods on the active compound contents, the antioxidant abilities, anti-inflammatory properties and enzyme inhibitory activities were evaluated. The plant materials were treated using shade-drying, microwave drying, sun-drying, infrared drying and oven drying. The seven active compounds were simultaneously determined by an HPLC method. Furthermore, the chemicals differences were assessed using Scanning electron microscopy, UV spectroscopy and infrared spectroscopy. The antioxidant capacities and protective effects on L02 cells induced by hydrogen peroxide were measured. The anti-inflammatory effects on lipopolysaccharide-induced RAW264.7 cells were investigated. The enzyme inhibitory activities were determined against α-amylase, α-glucosidase cholinesterases and tyrosinase. The results indicated that drying methods had significantly influences on the active compound contents and biological properties. In consideration of the contents of bioactive compound, the suitable drying methods were SHD, SD, OD and MD. The SHD sample exhibited stronger radical scavenging ability on DPPH, ABTS, hydroxyl and superoxide anions and higher reducing power compared with other samples prepared by SD, OD, MD and IRD. Moreover, SHD sample had strong protective effects against L02 cells damage induced by H2O2. SPF samples, especially SHD sample, significantly inhibited inflammatory factor secretion in LPS-stimulated RAW 264.7 cell. All studied SPF sample exhibited evidently inhibitory effects on the four enzymes. SHD sample possessed the highest inhibitory activity on α-glucosidase and α-amylase. While SHD and SD samples had the potential inhibitory effects on cholinesterases and tyrosinase. In consideration of active compound contents and biological activities, it was recommended that SHD and SD were applied for drying SPF at an industrial scale.

The Canadian Prairies are associated with high natural hydroclimatic variability including the frequent periodic occurrence of droughts and pluvials. These extremes carry various risks in-cluding significant damage to the economy, environment and society. The well-documented level of damage necessitates further risk assessment and planned reductions to vulnerability, particu-larly in light of a warming climate. A logical starting point involves awareness and information about the changing characteristics of such climate extremes. We focus on the compound occurrence of droughts and pluvials as the risks from this type of event are magnified compared to the hy-droclimatic extremes in isolation. Also, research on compound droughts and pluvials is limited. Therefore, the purpose of this paper is to synthesize recent literature concerning the risks of com-pound droughts and pluvials, including examples of past occurrences, with a focus on the Cana-dian Prairies. Since literature from the Prairies is limited, global work is also reviewed. Rela-tionships between drought and pluvials are characterized using the SPEI Global Monitor for the Prairies, emphasizing the recent past, and through synthesis from the Prairie literature. That re-search mostly considers drought and pluvials as separate events, but is integrated here to charac-terize the relationships of these extremes. Examples of periods of compound droughts and exces-sive rainfall provide insights into the regional hydroclimatic variability. Furthermore, most lit-erature on future projections strongly suggests that this variability is likely to increase, mainly driven by anthropogenic climate change. These findings suggest means of decreasing vulnerabil-ity and associated damages. Although the study area is the Canadian Prairies, the work is rele-vant to other regions that are becoming more vulnerable to increasing risks of and vulnerabilities to such compound extremes.

Nonlinear thermal transport of non-Newtonian polymer flows is an increasingly important area in materials engineering. Motivated by new developments in this area which entail more re-fined and mathematical frameworks, the present analysis investigates the boundary layer ap-proximation and heat transfer persuaded by a symmetrical cylindrical surface positioned hori-zontally. To simulate thermal relaxation impacts the bioconvection cross nanofluid flow Buongiorno model is deployed. The impact of the magnetic field applied on the nanofluid using the heat generation and melting phenomena are inspected. The nonlinear effect of thermosolutal buoyant forces is incorporated into the proposed model. The novel mathematical equations comprise thermophoresis and Brownian diffusion effects. Via robust transformation techniques, the primitive resulting partial equations for momentum, energy, concentration, and motile living microorganism are rendered into nonlinear ordinary equations with convective boundary postulates. An explicit and efficient numerical solver procedure in Mathematica 11.0 programming platform is developed to engage the nonlinear equations. The consequence of multiple governing parameters on dimensionless fluid profiles is inspected through plotted visuals and tables. Finally, outcomes declared on the surface drag force, heat, and mass transfer coefficients are exhibited through 3D visuals via different influential parameters.

High resolution melting (HRM) analysis is a powerful detection method for fast, high-throughput post-PCR analysis. A two-step HRM marker system was developed for identification of the N-, S-, R- and T-cytoplasms of onion. In the first step for identification of N-, S-, and R-cytoplasms, one forward primer was designed to the identical sequences of both cox1 and orf725 genes and two reverse primers specific to the polymorphic sequences of cox1 and orf725 genes were used. For the second step breeding lines with N-cytoplasm were evaluated with primers developed from the orfA501 sequence to distinguish between N- and T-cytoplasms. An amplicon with primers to the mitocondrial atp9 gene was used as an internal control. The two-step HRM marker system was tested using 246 onion plants. HRM analysis showed that the most common source of CMS, often used by Russian breeders, is S-cytoplasm, the rarest type of CMS is R-cytoplasm, and the proportion of T-cytoplasm among the analyzed breeding lines was 20.5%.

Cured-in-place pipe (CIPP) lining is a widely adopted method for pipeline renewal, offering advantages such as rapid installation and cost-effectiveness. However, concerns regarding the environmental impacts of volatile organic compound (VOC) emissions during the installation process have raised issues regarding the CIPP method. The literature review conducted in this paper indicated the need for stringent monitoring and management practices to mitigate adverse effects, emphasizing the importance of safe installation protocols. This paper presents the initial results of a case study focusing on VOC emissions, specifically investigating non-styrene polyester resins and water curing. To capture emissions from CIPP activities, the methodology involved air sampling using various equipment, including photoionization detectors (PID), summa canisters, passive worker sampler sorbent tubes, and method 13 cartridges. The preliminary findings indicate that non-styrene polyester resins do not exceed the exposure limits set out by the OSHA and USEPA. The future phases of this project will explore different resins and curing methods.

This study investigated the effects of modified rice bran arabinoxylan compound (RBAC) as a dietary supplement on the gut microbiota of healthy adults. Ten volunteers supplemented their diet with 1g of RBAC for six weeks and 3g of RBAC for another six weeks, with a three-week washout period. Faecal samples were collected every 3 weeks over 21 weeks. Microbiota from faecal samples were profiled using 16S rRNA sequencing. Assessment of alpha and beta microbiota diversity was performed using the QIIME2 platform. The results revealed that alpha and beta diversity were not associated with the experimental phase, interventional period, RBAC dosage, or time. However, statistical significance of participant was detected in alpha (p&lt;0.002) and beta (weighted unifrac, p=0.001) diversity. Explanatory factors including age and diet were significantly associated with alpha (p&lt;0.05) and beta (p&lt;0.01) diversity. The individual beta diversity of six participants significantly changed (p&lt;0.05) during the interventional period. Seven participants showed statistically significant taxonomic changes (ANCOM W≥5). These results classified four participants as responders to RBAC supplementation, with a further two participants likely responders. In conclusion, the gut microbiome is highly individualised and modulated by RBAC as a dietary supplement, dependent on lifestyle and dietary intake

Headspace solid phase microextraction (HS-SPME) coupled to gas chromatography-mass spectrometry is widely employed for volatile analyses of plants, including mapping populations used in plant breeding research. Studies often employ a single internal surrogate standard, even when multiple analytes are measured, with the assumption that any relative changes in matrix effects among individuals would be similar for all compounds, i.e. matrix effects do not show Compound × Individual interactions. We tested this assumption using individuals from two plant populations, an interspecific grape (Vitis spp.) mapping population (n = 140) and a tomato (Solanum spp.) recombinant inbred line (RIL) population (n = 148). Individual plants from the two populations were spiked with a cocktail of internal standards (n = 6, 9, respectively) prior to HS-SPME-GC-MS. Variation in the relative responses of internal standards indicated that Compound × Individual interactions exist but were different between the two populations. For the grape population, relative responses among pairs of internal standards varied considerably among individuals, with a maximum of 249% relative standard deviation (RSD) for the pair of [U13C]hexanal and [U13C]hexanol. However, in the tomato population, relative responses of internal standard pairs varied much less, with pairwise RSDs ranged from 8% to 56%. The approach described in this paper could be used to evaluate the suitability of using surrogate standards for HS-SPME-GC-MS studies in other plant populations.

Our investigation focused on the degradation of perfluorooctanoic acid (PFOA) and 6:2 fluorotelomer sulfonamide alkyl betaine (6:2 FTAB, Capstone B), using UV photolysis under various pH conditions. Initially, we used PFOA as a reference, finding a 90% decomposition after 360 minutes at the original (unadjusted) pH 5.6, with a decomposition rate constant of (1.08 ± 0.30) × 10-4 sec-1 and a half-life of 107 ± 2 minutes. At pH 4 and 7, degradation averaged 85% and 80%, respectively, while at pH 10, it reduced to 57%. For 6:2 FTAB at its natural pH 6.5, almost complete decomposition occurred. The primary UV transformation product was identified as 6:2 fluorotelomer sulfonic acid (6:2 FTSA), occasionally accompanied by shorter-chain perfluoroalkyl acids (PFAA). Interestingly, the overall decomposition percentages were unaffected by pH for 6:2 FTAB, though pH influenced rate constants and half-lives. In PFOA degradation, direct photolysis and reaction with hydrated electrons were presumed mechanisms, excluding the involvement of hydroxyl radicals. The role of superoxide radicals remains uncertain. For 6:2 FTAB, both direct and indirect photolysis were observed, with potential involvement of hydroxyl, superoxide radicals, and/or other reactive oxygen species (ROS). Clarification is needed regarding the role of eaq- in the degradation of 6:2 FTAB.

Malignant pleural mesothelioma (MPM) has limited treatment options and poor prognosis. Frequent inactivation of the tumour suppressors BAP1, NF2 and P16 may differentially sensitise tumours to treatments. We have established chick chorioallantoic membrane (CAM) xenograft models of low-passage MPM cell lines and protocols for evaluating drug responses. Ten cell lines, representing the spectrum of histological subtypes and tumour suppressor status, were dual labelled for fluorescence/bioluminescence imaging and implanted on the CAM at E7. Bioluminescence was used to assess viability of primary tumours, which were excised at E14 for immunohistological staining or real-time PCR. All MPM cell lines engrafted efficiently forming vascularised nodules, however their size, morphology and interaction with chick cells varied. MPM phenotypes including local invasion, fibroblast recruitment, tumour angiogenesis and vascular remodelling were evident. Bioluminescence imaging could be used to reliably estimate tumour burden pre- and post-treatment, correlating with tumour weight and Ki-67 staining. In conclusion, MPM-CAM models recapitulate important features of the disease and are suitable to assess therapies using a broad range of MPM cell lines that allow histological or genetic stratification. They are amenable to multi-modal imaging, offering a time and cost-efficient, 3Rs-compliant alternative to rodent xenograft models to prioritise candidate compounds from in vitro studies.

Background: Disability and caste are two different forms of oppression, however Dalits and people with disabilities commonly face similar types of marginalities. Dalit women with disabilities may experience double discrimination because of the intersectionality of disability and caste. This study examines whether the disability and caste identity of women together affects and compounds the utilization of maternal healthcare services. Methods: A cross-sectional survey was conducted using a semi-structured questionnaire among a total of 354 Dalit and non-Dalit women, with and without a disability aged between 15 – 49 years. Maternal healthcare service utilization was assessed by Ante-Natal Care (ANC), health facility (HF) delivery, and Post-Natal Care (PNC) during the last pregnancy. Logistic regression was performed to detect the predictors of service utilization and identify whether disability and caste were associated with service utilization. First, disability and caste were fitted separately in models. Secondly, the intersectionality of disability and caste was tested by the inclusion of disability*caste interaction term. Finally, the confounding effect of socio-demographic factors was investigated. Results: Out of surveyed women, 73% had 4+ ANC visits, 65% had HF delivery and 29% had a PNC visit during their last pregnancy. Women with a disability had lower odds of HF delivery (OR 0.50, CI 0.30 – 0.84) and PNC (OR 0.47, CI 0.25 – 0.88) than women without a disability. Adjustment for women’s age and household wealth explained associations in HF delivery by women with disabilities. There was no association between caste and service utilization. Disability overrode caste and there was no other evidence of effect modification by women’s caste status in the utilization. However, a weak interaction effect in the utilization of ANC services was found in the caste group by their education (OR 0.19, 95% CI 0.05 – 0.74). Conclusions: Disabled women – whether Dalit or non-Dalit - had lower rates of utilizing all maternal healthcare services than non-disabled women. However, Dalit women with disabilities were more likely to receive PNC than non-Dalit women with disabilities. Increasing equity in maternal healthcare service utilization requires that traditional approaches to service development and program intervention to be re-examined and more nuanced interventions considered to ensure improved access and outcome among all vulnerable groups.

The main aim of this study is to investigate the optimization of the technological process for selective laser melting (SLM) additive manufacturing. The group of process parameters considered was selected from the first-stage parameters identified in preliminary research. Samples manufactured using three different sets of parameter values were subjected to static tensile and compression tests. The samples were also subjected to dynamic Split–Hopkinson tests. To verify the microstructural changes after the dynamic tests, microstructural analyses were conducted. Additionally, the element deformation during the tensile tests was analyzed using digital image correlation (DIC). To analyze the influence of the selected parameters and verify the layered structure of the manufactured elements, sclerometer scratch hardness tests were carried out on each sample. Basing on the research results it was possible to observe the porosity growth mechanism and its influence on the material strength (including static and dynamic tests). Parameters modifications that caused 20% lower energy density, elongation of the elements during tensile testing decreased twice, which was strictly connected with porosity growth. An increase of energy density by almost three times caused a significant reduction of force fluctuations differences between both tested surfaces (parallel and perpendicular to the building platform) during sclerometer hardness testing. That kind of phenomenon had been taken into account in the microstructure investigations before and after dynamic testing where it had been spotted a positive impact on material deformations based on fused material grains formation after SLM processing.

Electron Beam Melting (EBM) is an increasingly used Additive Manufacturing (AM) technique employed by many industrial sectors, including the medical device and aerospace industries. In-process EBM monitoring for quality assurance purposes has been a popular research area. Electronic imaging has recently been investigated as one of the in-process EBM data collection methods, alongside thermal/ optical imaging techniques. Despite certain capabilities of an electronic imaging system have been investigated, experiments are yet to be carried out to benchmark one of the most important features of any imaging systems – spatial resolution. This article addresses this knowledge gap by: (1) proposing an indicator for the estimation of spatial resolution which includes the Backscattered Electrons (BSE) information depth, (2) estimating the achievable spatial resolution when electronic imaging is carried out inside an Arcam A1 EBM machine, and (3) presenting an experimental method to conduct edge resolution evaluation with the EBM machine. Analyses of experimental results indicated that the spatial resolution was of the order of 0.3mm-0.4mm when electronic imaging was carried out at room temperature. It is believed that by disseminating an analysis and experimental method to estimate and quantify spatial resolution, this study has contributed to the on-going quality assessment research in the field of in-process monitoring of the EBM process.

Acute lymphoblastic leukemia (ALL) is the most common type of leukemia affecting children under the age of 15 years old in Malaysia. Chemotherapy is the primary treatment for cancer, which involves the intake of chemotherapeutic drugs to kill cancer cells. Glucocorticoids such as dexamethasone are chemotherapeutic agents used in the treatment of ALL. Although dexamethasone is highly effective, it is also associated with adverse effects such as bone fractures and organ toxicity. Therefore, there is a need to develop a new anticancer drug which milder side effects and better efficacy. Organometallic compounds such as organotin have a high potential to be developed as an antineoplastic agent and show high specificity towards cancer cells compared to normal cells. This study is done to evaluate the cytotoxic effects of diphenyltin(IV) diisopropyl dithiocarbamate (DPDT) against leukemic cells CCL-119 using the Trypan Blue exclusion (TBE) method at the intervals of 24, 48 and 72 h. Dexamethasone was used as a positive control. The cell’s morphological changes were observed at 12, 24 and 48 h using the IC₅₀ values obtained using TBE assay. Results show that DPDT has a lower IC₅₀ value than dexamethasone against CCL-119 cells at 24 h with a value of 4.16 ± 0.44µM and a selectivity index of 2.02. Dexamethasone exhibited cytotoxic effects against CCL-119 but only IC₂₅ and IC₁₀ values were obtained. Cytotoxicity testing has shown that DPDT is toxic on CCL-119 cells with IC₅₀ values of less than 10µM. Morphological changes in cells show characteristics of apoptosis such as cell shrinkage, blebbing and formation of apoptotic bodies. In conclusion, DPDT has the potential to be made into an antineoplastic agent but requires a more detailed study involving the molecular pathway of DPDT leading to cell death.

The purpose of this work is to investigate the protein kinase inhibitory activity of constituents from ethyl acetate soluble fraction of Acacia auriculiformis stem bark. Column chromatography, gel filtration and NMR spectroscopy were used to purified and characterized betulin from the extract. Betulin which is a known inducer of apoptosis was screened against a panel of 16 disease-related protein kinases. Betulin was shown to inhibit Abelson murine leukemia viral oncogene homolog 1 (ABL1) kinase, casein kinase 1epsilon (CK1epsilon), glycogen synthase kinase 3alpha/β (GSK-3alpha/β), Janus kinase 3 (JAK3), NIMA Related Kinase 6 (NEK6) and vascular endothelial growth factor receptor 2 kinase (VEGFR2) and with activity in µM range. The effect of betulin on the cell viability of doxorubicin-resistant K562R chronic myelogenous leukemia cells was then verified to underline its putative use as anti-cancer compound. Betulin was shown to modulate the mitogen-activated protein (MAP) kinase pathway similarly to imatinib mesylate, a well-known inhibitor of ABL1 kinase. The interaction of betulin and ABL1 was studied by molecular docking showing an interaction of the inhibitor with the ATP binding pocket. Altogether, these data demonstrate that betulin is a multi-target inhibitor of protein kinases, an activity that can contribute to the anticancer properties of the natural compound and notably for treatment of leukemia.

Mutations in the SACS gene are associated with autosomal recessive spastic ataxia of Charlevoix-Saguenay disease (ARSACS) or complex clinical phenotypes of Charcot-Marie-Tooth disease (CMT). This study aimed to identify SACS mutations in a Korean CMT cohort with cerebellar ataxia and spasticity. As a result, eight pathogenic SACS mutations in four families were identified as the underlying causes of these complex phenotypes. The prevalence of CMT families with SACS mutations was determined to be 0.3%. All the patients showed sensory, motor, and gait disturbances with increased deep tendon reflexes. Lower limb magnetic resonance imaging (MRI) was done in four patients, and all had fatty replacements. Of note, they all had similar fatty infiltrations between the proximal and distal lower limb muscles, different from the neuromuscular imaging feature in most CMT patients without SACS mutations who had distal dominant fatty involvement. Therefore, these findings were considered a characteristic feature in CMT patients with SACS mutations. Although further studies with more cases are needed, our results highlight lower extremity MRI findings in CMT patients with SACS mutations and broaden the clinical spectrum. We suggest screening for SACS in recessive CMT patients with complex phenotypes of ataxia and spasticity.

Natural products, especially biologically active compounds derived from plants, have been and continue to be invaluable in anticancer research and therapeutic discoveries. Rice bran arabinoxylan compound (RBAC) is a heteropolysaccharide extract of defatted rice bran obtained through enzymatic treatment with Lentinus Edodes mycelium. RBAC exhibited antitumour properties by arresting in vivo tumour growth in several murine models. In vitro experiments showed RBAC to promote apoptosis in cancer cells by increasing the susceptibility of CD95 (Fas/APO-1) ligands and downregulating Bcl-2 proteins to trigger the permeabilisation of the mitochondrial membrane. RBAC may restore immune dysfunction in cancer patients, most notably by upregulating natural killer cell activity and modulating cytokine production to enhance inflammatory and cytotoxic responses. As such, RBAC acts on the immune system to enhance chemopreventative activity and block tumourigenesis. In treatment, RBAC works synergistically with other natural products and chemotherapeutic agents, such as daunorubicin and paclitaxel, by enhancing drug transport to increase DNA damage in tumours and reduce proliferation. In a clinical trial, combining RBAC with chemoembolization in treating liver cancer showed improved response, reduced recurrence, and prolonged survival time. RBAC has been shown to augment the endogenous antioxidant system to prevent oxidative stress and thus protect against the harmful side effects of radiation therapy. RBAC also has chemoprotective effects, with animal and human studies showing reduced toxicity and side effects from chemotherapy, leading to improved health-related quality of life. Meta-analysing the best available evidence indicates that RBAC treatment increases the odds of survival among cancer patients by 4.02 times (95% CI: 1.67, 9.69) in the first year and 2.89 (95% CI: 1.56, 5.35) times in the second year after commencing treatment, compared to those not treated with RBAC. Notwithstanding, additional research is needed to characterise, quantify, and standardise the active ingredients in RBAC responsible for the anticancer effects. More well-designed, large-scale clinical trials are required to further substantiate the treatment efficacies.

Initial water content significantly affects the efficiency of soil stabilization. In this study, the effects of initial water content on the compressibility, strength, microstructure and composition of a lean clay soil stabilized by compound calcium-based stabilizer were investigated by static compaction test, unconfined compression test, optical microscope observations, environment scanning electron microscopy, energy dispersive X-ray spectroscopy and X-ray diffraction spectroscopy. The results indicate that as the initial water content increases in the range studied, both the compaction energy and the maximum compaction force decrease linearly and there are less soil aggregates or agglomerations, and smaller proportion of large pores in the compacted mixture structure. In addition, for specimens cured with or without external water supply and under different compaction degrees, the variation law of the unconfined compressive strength with initial water content is different and the highest strength value is obtained at various initial water contents. With the increase of initial water content, the percentage of oxygen element tends to increase in the reaction products of the calcium-based stabilizer, whereas the crystalline mineral of the soil did not change obviously.

The lactic acid bacteria Streptococcus thermophilus and Lactobacillus helveticus are commonly used as starter cultures in dairy product production. This study aimed to investigate the characteristics of fermented milk using different ratios of these strains and analyze the changes in volatile compounds during fermentation and storage. The 10:1 ratio of Streptococcus thermophilus CICC 6063 to Lactobacillus helveticus CICC 6064 showed optimal fermentation time (4.2 h), viable cell count (9.64 log10 colony-forming units/mL), and sensory evaluation score (79.1 points). In total, 56 volatile compounds were identified and quantified by solid-phase microextraction and gas chromatography–mass spectrometry (SPME-GC-MS), including aldehydes, ketones, acids, alcohols, esters, and others. Among these, acetaldehyde, 2,3-butanedione, 2,3-pentanedione, 2-heptanone, acetoin, and 1-heptanol had the highest odor activity values and contributed to the characteristic flavor of fermented milk. The concentrations and types of key flavor compounds reached their peak at the end of fermentation. Throughout the fermentation and storage process, the levels of 2,3-pentanedione and acetoin exhibited synergistic dynamics. These findings enhance our understanding of the chemical and molecular characteristics of milk fermented with Streptococcus thermophilus and Lactobacillus helveticus, providing a basis for improving the flavor and odor of dairy products during fermentation and storage.

For each $t\in(-1,1)$, exact values of the least upper bounds $$ H(t)=\sup_{\E X=t,\,\E X^2=1} \frac{\E\abs{X}^3}{\E \abs{X-t}^3},\quad \sup_{\E X=t,\,\E X^2=1} \frac{L_1(X)}{L_1(X-t)} $$ are obtained, where $L_1(X)=\E|X|^3/(\E X^2)^{3/2}$ is the non-cental Lyapunov ratio. It is demonstrated that these values are attained only at two-point distributions. As a corollary, S.\,Shorgin's conjecture is proved that states that the exact value is $$ \sup\frac{L_1(X)}{L_1(X-\E X)}= \frac{\sqrt{17 + 7\sqrt7}}{4} = 1.4899\ldots, $$ where the supremum is taken over all non-degenerate distributions of the random variable $X$ with the finite third moment. Also, in terms of the central Lyapunov ratio $L_1(X-\E X)$, an analog of the Berry--Esseen inequality is proved for Poisson random sums of independent identically distributed random variables with the constant $$ 0.3031\cdot H\left(\frac{\E X}{\sqrt{\E X^2}}\right) \left(1-\frac{(\E X)^2}{\E X^2}\right)^{3/2} \le 0.3031\cdot \frac{\sqrt{17 + 7\sqrt7}}{4}<0.4517.$$ where $\Law(X)$ is the common distribution of the summands.

Soy leghemoglobin (LegH) has been gaining interest over the last years as an efficient flavor and aroma compound in plant-based meat substitutes. Hence, in the following article we demonstrate the methods for LegH production using a recombinant Komagataella phaffii strain. Multiple fed-batch fermentation with an alternative to BSM medium, where glucose was used as the main carbon source, were implemented and the growth kinetics, e.g., maximal specific biomass growth - 0.239 g·g−1·h−1, biomass yield from substrate - 0.298 g·g−1 and maximal specific substrate consumption rate - 0.81 g·g−1·h−1, were identified. Leghemoglobin production resulted in a yield of 0.513 mg·gDCW 1, while the highest biomass density achieved in the study was 121.80 gDCW·L 1. The applied medium showed potential for additional optimization studies, as in contrast to BSM, made it possible to separate pH control from nitrogen supply, does not affect medium turbidity measurements and does not induce metabolite synthesis during yeast biomass growth.

Compound-specific isotope analysis (CSIA) can provide unique insights into the cycling of elements including carbon and nitrogen. One approach for CSIA is the use of high-performance liquid chromatography (HPLC) to separate compounds of interest, followed by analysis of these compounds using an elemental analyzer coupled to an isotope ratio mass spectrometer. A key component of this technique is the fraction collector, which automatically collects compounds as they are separated by HPLC. Here we present a fraction collector which is a simple adaptation of a 3D printer, and thus can be easily adopted by any laboratory already equipped for HPLC. In addition to the much lower cost compared to commercial alternatives, this adaptation has the advantage for CSIA that the 3D-printer is able to heat the collected fractions, which is not true for many commercial fraction collectors. Heating allows faster evaporation of the solvent, so that the dried compounds can be measured by EA-IRMS immediately. The procedure can be repeated consecutively so that dilute solutions can have the compounds concentrated for analysis. Any computer-controlled HPLC can be integrated to the fraction collector used here by means of AutoIt.

Alzheimer's disease is characterized by a progressive decline of cognitive functions. The class of drugs used for the treatment are acetylcholinesterase inhibitors. Essential oils have contributed to folk medicine and discovery of new drugs for a long time. The purpose of the study was to investigate the in vitro and in silico the anti-acetylcholinesterase activity, as well as acute toxicity of the essential oil of Lippia origanoides. EOLO was obtained by hydrostelting and analyzed by gas chromatography-mass spectrometry. The inhibition assay of acetylcholinesterase enzyme activity was evaluated in vitro, as well as in silico by docking. The effects of EOLO on hematological, biochemical and behavioral parameters were analyzed in mices. We expose that EOLO shows good anti-acetylcholinesterase activity and low toxicity, possibly resulting from the action of the majority compounds thymol, carvacrol and p-cymene. The anti-acetylcholinesterase potential in vitro demonstrating a 70% inhibition. The docking results elucidated the participation of the major phenolics in AChE inhibition by interacting with the catalytic cavity of AchE. The acute oral toxicity test classified as low toxicity. These results contribute to expand the knowledge about essential oil of Lippia origanoides. Therefore, appears to be promising for herbal medicine production with anti-acetylcholinesterase and antioxidant activity.

In this study, the effect of hot stamping forming process on the properties change of compound layer in Al–Si coated high-strength steel sheet with different thickness was investigated. The coating layer in hot stamped high-strength steel sheet was composed of a diffusion layer and a compound layer. As the hot stamping temperature and holding time for forming increased, the thickness of the compound layer in the Al–Si coated high-strength steel sheet increased. The thickness of coating layer with the hot stamping for 500 sec at 890, 910 and 950 °C was obtained 8.9, 11.8, and 20.6 micrometer, respectively. The thickness of coating layer with hot stamping for 180, 500 and 550 sec at 910 ^oC was obtained 5.7, 11.8, and 17.8 micrometer, respectively. The compound layer in hot stamped high-strength steel sheet with Al–Si coating layer consists of Al_5.4Fe₂ and Fe₂Si phases. In the compound layer, Al and Si were irregularly distributed.

Nine variants of regular lattice structures with different relative densities have been designed and successfully manufactured. The produced structures have been subjected to geometrical quality control, and the manufacturability of the implemented selective laser melting SLM technique has been assessed. It was found that the dimensions of the produced lattice struts differ from those of the designed struts. These deviations depend on the direction of geometrical evaluation. Additionally, the microstructures and phase compositions of the obtained structures were characterized and compared with those of conventionally produced 316L stainless steel. The microstructure analysis and X-Ray Diffraction XRD patterns revealed a single austenite phase in the SLM samples. Both a certain broadening and a displacement of the austenite peaks were observed due to residual stresses and a crystallographic texture induced by the SLM process. Furthermore, the mechanical behavior of the lattice structure material has been defined. It was demonstrated that under both quasi-static and dynamic testing, lattice structures with high relative densities are stretch-dominated, whereas those with low relative densities are bending-dominated. Moreover, the linear relationship between the energy absorption and relative density under dynamic loading conditions has been defined

Adult neurogenesis involves generation of functional neurons from neural progenitor cells, which have the potential to complement and restore damaged neurons and neural circuits. Therefore, the development of drugs that stimulate neurogenesis represents a promising strategy in stem cell therapy and neural regeneration, greatly facilitating the reconstruction of neural circuits in cases of neurodegeneration and brain injury. Our study reveals that compound A5, previously designed and synthesized by our team, exhibits remarkable neuritogenic activities, effectively inducing neurogenesis in neural stem/progenitor cells (NSPCs). Subsequently, transcriptome analysis using high-throughput Illumina RNA-seq technology was performed to further elucidate the underlying molecular mechanisms by which compound A5 promotes neurogenesis. Notably, comparative transcriptome analysis showed that the up-regulated genes were mainly associated with neurogenesis and the down-regulated genes were mainly concerned with cell cycle progression. Furthermore, we confirmed that compound A5 significantly affected the expression of transcription factors related to neurogenesis and cell cycle regulatory proteins. Collectively, these findings identify a new compound with neurogenic activity and may provide insights into drug discovery for neural repair and regeneration.

The management of wounds is a significant issue that impacts individuals, healthcare systems, and society at large. This study evaluates Rigemed D (RD), a novel compound extracted from Bovine Colostrum with a unique combination of 20 different growth factors and exosomes, known for its exceptional properties in promoting cell proliferation and regeneration. This study aims to determine the effects of different doses of RD on cell survival (using CCK8) and to assess its antioxidant effect using the Comet assay in the presence of hydrogen peroxide (H2O2) on two human cell types, fibroblasts and immortalised keratinocytes (HaCat cell line). The study results revealed that RD, at doses of 1, 1.5, and 2 % v/v, significantly improved cell viability four, six, and 12 times, respectively, compared to the control group (p < 0.00001). Furthermore, the Comet assay showed a two-fold reduction in DNA damage in RD-treated cells at 2% v/v without and with H2O2 (p < 0.001). The effect of RD on cell proliferation and migration was evaluated using a scratch assay on fibroblasts and HaCat cells. The findings demonstrated a four-fold increase in cell proliferation and migration at 1 and 24 hours (p < 0.001). Immunohistochemistry confirmed this claim (p < 0.001). Also, angiogenesis induction of RD was assessed on human vein umbilical endothelial cells (HUVEC), showing that RD significantly enhanced the proliferation of endothelial HUVEC cells (p < 0.0001). In conclusion, RD is a promising vitalising compound with exceptional capabilities in promoting cell proliferation, migration, and regeneration. It also shows a significant antioxidant effect and has the potential to support all phases of wound healing involving cell proliferation, re-epithelialisation, angiogenesis, and tissue maturation. Hence, the present formulation presents a promising foundation for developing a 3D bio-printed membrane, potentially expediting the wound healing process.