In this study, the apparent variation range of acoustical parameters were investigated in a concert hall. The initial time delay gap (ITDG) was evaluated in terms of its just noticeable difference (JND) through two instruments, the cello and the trumpet. Even though the IDTG values were prolonged over the measurements and were not significantly varied, an ITDG range of 22 - 220 ms in increments of 91 steps was produced electro-acoustically in an anechoic chamber with a loudspeaker. The result of JNDc ((delta gap/gap) was rated 0.059 and 0.081 at 50% “different” judgement ranges for the cello and trumpet tracks, respectively. The effective duration of the autocorrection function (ACF) of the continuous brainwaves (CBWs) within the alpha (8-13 Hz) frequency range on the left hemisphere responding to 91-step ITDG increments revealed that the continuous ratio minimum Tauee e of CBW was approximately equal to 0.28 s on the trumpet. The continuous ratios of Tauee e_min ((Tauee e_min_rear - Tauee e_min_front)/ Tauee e_min_front) of CBWs were constantly at 0.4. Furthermore, a homologous period of resonance between the subjective JNDc and Tauee e values of the ACF of CBWs in the alpha range allowed us to conclude that the subjective JND of the ITDG in a room is related to the W_IACC value of the interaural cross-correlation function, which reflect the characteristics of source signal themselves and arouse the activities of brain on the right hemisphere (p < 0.01).

MIMO (multiple-input multiple-output) radar provides much more flexibility than the traditional radar for its ability to realize far more observation channels than the actual number of T/R (transmit and receive) elements. Designing the array of MIMO imaging radar, the commonly used virtual array theory generally assumes that all elements are placed on the same line. However, due to the physical size of the antennas and coupling effect between T/R elements, a certain height difference between T/R arrays is essential, resulting in the defocusing of edge points of the scene. On the other hand, the virtual array theory implies far-field approximation, leading to inevitable high grating lobes in the imaging result of near-field edge points of the scene observed by common MIMO array. To tackle these problems, this paper derives the relationship between target’s PSF (point spread function) and pattern of T/R arrays, by which the design criterion of near-field imaging MIMO array is presented. Firstly, the proper height between T/R arrays is designed to focus the near-field edge points well. Secondly, the far-field array is modified to suppress the grating lobes in the near-field area. Finally, the validity of the proposed methods is verified by simulations and an experiment.

The degree of ore rock fragmentation of mine blasting is an important index for evaluating the effect of engineering blasting. In order to study the effect of millisecond delayed blasting on the internal fragmentation of the ore rock, LS-DYNA numerical simulation software was used to obtain the damage characteristics of the ore rock in the blasting area using the RHT model. The Mohr-Coulomb strength damage criterion was applied to analyze the internal stress state of the ore rock, and the effects of 25ms, 50ms and 75ms delay time conditions on ore rock fragmentation were studied. The results show that, within a certain range of delay time, the degree of rock fragmentation increases with the increase of delay time. The stress state in the ore rock due to blasting is strengthened with the increase of delay time in the direction of the blast hole, which shows that the stress concentration is strengthened from the excavation face to the interior of the ore rock. The damage and the degree of fragmentation show a characteristic relationship of 25ms＜50ms＜75ms, which is verified by carrying out blasting experiments on site.

Incremental stability analysis for time-delay systems has attracted more and more attentions for its contemporary applications in transportation processes, population dynamics, economics, satellite positions, etc. This paper researches criteria on v(t)-incremental stability, which is defined to demonstrate the convergence rate for incremental stability, for time-delay systems. Firstly, the sufficient conditions for v(t)-incremental stability for time-delay systems with continuous right-hands are studied, and several corollaries for specific cases are provided. As for time-delay systems with discontinuous right-hands, after expounding the relevant conditions for the existence and uniqueness of the Filippov solution, by using approximation methods, sufficient conditions for v(t)-incremental stability are obtained. The conclusions are applied to linear switched time-delay systems and Hopfield neural network system with composite right-hand afterwards.

The relaxation process of lithium batteries caused by load variation is considered. It is shown that such processes have strong dependence on internal physical and chemical processes and battery technical conditions. Theoretical expressions of the relaxation process caused by a step-like load variation have been obtained for 1^st and 2^nd order equivalent electrical circuits. The experimental investigations show that the obtained models fit the real relaxation processes and the behavior of the identified parameters could be explained by specific features of physical and chemical processes within the lithium battery. It should be noted that the obtained results can be generalized for a different type of electrochemical power source. The proposed approach makes it possible to provide means for electrochemical power source characterization and diagnostic, the main advantages of which are good time localization of measurement procedures and inexpensive apparatus implementation.

We consider an alternative formula for time delay in gravitational lensing. Imposing a smoothness condition on the gravitationally deformed paths followed by the photons from the source to the observer, we show that our formula displays the same degrees of freedom of the standard one. In addition to this, it is shown that the standard expression for time delay is recovered when small angles are involved. These two features strongly support the claim that the formula for time delay studied in this paper is the generalization to arbitrary angles of the standard one, which is valid at small angles. This could therefore result in a useful tool in view of softening the known discrepancy between the various estimates of the Hubble constant. As an aside, two interesting consequences of our proposal for time delay are discussed: the existence of a constraint on the gravitational potential generated by the lens and a formula for the mass of the lens in the case of central potential.

One application of the Cosmological Gravitational Lensing in General Relativity is the measurement of the Hubble constant H_0 using the time delay Delta t between multiple images of lensed quasars. This method has already been applied, obtaining a value of H_0 compatible with that obtained from the SNe 1A, but non compatible with that obtained studying the anisotropies of the CMB. This difference could be a statistical fluctuation or an indication of new physics beyond the Standard Model of Cosmology, so it desirable to improve the precision of the measurements. At the current technological capabilities it is possible to obtain H_0 to a percent level uncertainty, so a more accurate theoretical model could be necessary in order to increase the precision about the determination of H_0. The actual formula which relates Delta t with H_0 is approximated; in this paper we expose a proposal to go beyond the previous analysis and, within the context of a new model, we obtain a more precise formula than that present in the Literature.

The measurements of the proton electromagnetic form factors in the time-like region using the initial state radiation technique are reviewed. Recent experimental studies have shown that initial state radiation processes at high luminosity electron-positron colliders can be effectively used to probe the electromagnetic structure of hadrons. The BABAR experiment at the B-factory PEP-II in Stanford and the BESIII experiment at the $\tau$-charm factory BEPC-II in Beijing have measured the time-like form factors of the proton using the initial state radiation process $e^{+}e^{-}\to pbar{p}\gamma$. The two kinematical regions where the photon is emitted from the initial state at small and large polar angles have been investigated. In the first case the photon is in the region not covered by the detector acceptance and is not detected. The Born cross section and the proton effective form factor have been measured over a wide and continuous range of the the momentum transfer squared $q^2$ from threshold up to ~42 (GeV/c)$^2$. The ratio of electric and magnetic form factors of the proton has been also determined. In this report, the theoretical aspect and the experimental studies of the initial state radiation process $e^{+}e^{-}\to p\bar{p}\gamma$ are described. The measurements of the Born cross section and the proton form factors obtained in these analyses near the threshold region and in the relatively large $q^2$ region are examined. The experimental results are compared to the predictions from theory and models. Their impact on our understanding of the nucleon structure is discussed.

Multi-gap Resistive Plate Chamber has been attracting increasing attention and has been studied in recent decades because of its good efficiency, high time resolution and relatively low cost. It has become a new standard technology for the Time of Flight system in particle and high energy physics experiments. In this paper, we introduce the operation principle and structure of the MRPC detector and review the applications on the Time of Flight system in several famous experiments, such as STAR, CBM and SoLID. The performances including time resolution and particle identification are discussed in detail. Some recent advances and perspectives with regard to the future development of the next generation MRPC are also outlined.

The exceptional performance advantages of the fiber optic gyroscope (FOG) position it as a dominant player in middle and high-end inertial navigation systems. To prevent the loss of sensor precision caused by algorithm design and simplify the complex modeling strategy in traditional methods. We gradually demonstrate the significant role of Convolutional Neural Network (CNN) in the navigation system based on FOG, and utilize the particle swarm optimization algorithm (PSO) to expedite the convergence of the network. The experimental results demonstrate that the initial alignment method based on deep learning is more accurate than the traditional method. The attitude angle error is reduced by 81.25%, 92.54% and 36.53% respectively. The research provides support for the future application of deep learning in optical navigation systems.

This research not only dedicated a less restrictive method of iteration-varying function for a learning control law to design a controller but also synchronize two nonlinear systems with free time-delay. In addition, the mathematical theory of system synchronization has proved rigorously and the theory verified through an example to demonstrate the behavior of each parameter in the theory. The design of a controller using the iterative learning control law is significant for robotic tracking. The controller in this research generates a feed-forward control input using the error dynamics among the drive-response systems. The error dynamics satisfies the Lyapunov function and the combination of output errors, which respectively represented relative estimated differences of the drive-response systems. The iterative learning control rule serves the function of a filter adding previous control error after the end of each iteration. The numerical example of a synchronous system is given a Lorenz system for driving and another with the iterative learning control law for response under different initial condition. The results verify and demonstrate the proposed mathematical theory. The simulation exhibits consistency in the behavior of each parameter to match mathematical theory.

The RPL protocol is a routing protocol for low power and lossy networks. In such a network, energy is a very scarce resource; so many studies are focused on minimizing global energy consumption. End-to-end latency is another important performance indicator of the network, but existing research tends to focus more on energy consumption and ignore the end-to-end delay of data transmission. In this paper, we propose a kind of energy equalization routing protocol to maximize the surviving time of the restricted nodes so that the energy consumed by each node is close to each other. At the same time, a multi-path forwarding route is proposed based on the cache utilization. The data is sent to the sink node through different parent nodes at a certain probability, not only by selecting the preferred parent node, thus avoiding buffer overflow and reducing end-to-end delay. Finally, the two algorithms are combined to accommodate different application scenarios. The experimental results show that the proposed three improved schemes improve the reliability of the routing, extend the lifetime of the network, reduce the end-to-end delay, and reduce the number of DAG reconfiguration.

This study aims to spatially analyze the distribution characteristics of vacant homes in Asan-si, Chungcheongnam-do, and understand the differences in factors causing vacant homes by type. We use a variety of statistical methods to examine these factors and identify key influencing factors such as the number of vacant stores, changes in overall population, land use complexity, and physical characteristics of land and buildings. The findings reveal that the factors contributing to the occurrence of vacant homes vary significantly by region and property type, highlighting the need for region-specific policies. For instance, in old town areas, small lot ratios and land use complexity are significant, while in rural village, the average number of floors and land use complexity play a major role. This study underscores the diversity of factors influencing vacant homes, suggesting that policies should be tailored to the unique characteristics of different regions to effectively address this issue.

With the development of designing and manufacturing level for micro-electromechanical system (MEMS) gyroscopes, the control circuit system becomes a key point to determine their internal performances. Nevertheless, phase delay of electron components may result in some serious hazards. This paper describes a real-time circuit phase delay correction system for MEMS vibratory gyroscopes. A detailed theoretical analysis is provided to clarify the influences of circuit phase delay on the in-phase and quadrature (IQ) coupling characteristics and zero rate output (ZRO) utilizing force-to-rebalance (FTR) closed-loop detection and quadrature correction system. By deducing the relationship between amplitude-frequency, phase-frequency of MEMS gyroscope and the phase relationship of the whole control loop, a real-time correction system is proposed to automatically adjust the phase reference value of phase-locked loop (PLL) and thus compensate for the real-time circuit phase delay. The experimental results show that the correction system can accurately measure and compensate the circuit phase delay in real time. Furthermore, the unwanted IQ coupling can be eliminated and the ZRO is decreased by 755% to 0.095°/s. This correction system realizes a small angle random walk of 0.978°/√h, and a low bias instability of 9.458°/h together with a scale factor nonlinearity of 255 ppm at room temperature. Besides, the thermal drift of ZRO is reduced to 0.0034°/s/°C at a temperature range from -20°C to 70°C.

In this research article we solve the problem of synchronization and anti-synchronization of chaotic systems described by discrete and time-delayed variable fractional order differential equations. To guarantee the synchronization and anti-synchronization of these systems, we use the well-known PID control theory and the Lyapunov-Krasovskii stability theory for discrete systems of variable fractional order.We illustrate the results obtained through simulation with examples, in which it can be seen that our results are satisfactory, thus achieving synchronization and anti-synchronization of chaotic systems of variable fractional order with discrete time delay.

In this paper, we consider an epidemiological Susceptible-Infected-Susceptible (SIS) model in which the individuals cured from the infection return back into the group of people endangered by the infection. Delay differential equations were introduced to create more realistic models since many processes depend on past history. Many different mathematical methods, including the Susceptible-Infected-Recovered (SIR) model as well as derivatives thereof, can be used to prognose the spread of many various infectious diseases, including Covid-19.We use a nonlinear differential system with time delay as a mathematical formulation of this model. It is examined by the existence of a positive solution which is bounded by two functions $k_1, k_2\in C([t_0,\infty),(0,\infty))$ with constants $\lambda_1 > 0,\,\lambda_2 > 0$ where $0<\lambda_1\leq \lambda_2$. The conditions are put in place for existence of a positive solution that approaches zero in infinity, if $t\to\infty$. Infectious diseases accompany a person throughout their entire life, and in the history of mankind often appeared in frequent epidemics caused high mortality. The occurrence of infectious diseases in the population represents a serious health, social and economic problem. There is a lot of ambiguity concerning the time span and final spread of the epidemic thus making it very demanding for the governing bodies, healthcare institutions, and economic sector to precisely judge the future development.Several examples are shown at the end of this paper.

We are currently facing a potential ‘polycrisis’, a critical inflection point that requires a whole-of-society response aimed at building collective foresight and preparedness for short-, medium-, and long-term risks. The role of higher education institutions and social stakeholders is decisive to make an impact. This paper depicts the alignment of academia, governance, and industry with the aim to challenge, inspire, and encourage universities to go beyond commodified courses and mere employability, enhance student growth and bind macro-scale measures that lead to a sustainable future. A modest teaching innovation project has served as a transforming lever, with the private sector joining in, to create a platform that reaches more than 50 000 undergraduate students and teaching staff. The resulting structure, rooted in the University’s strategic plan, has served to channel local and regional initiatives, establish effective partnerships with broad social members, raise awareness and promote actions to advance in the pursuit of Sustainable Development Goals. Chronology, materials and methodology, together with a description of the different courses, programmes and actions are provided. The paper concludes with some recommendations for future research, policy and cooperation among stakeholders. Research methodology posted on clinicaltrials.gov under ID NCT04392869, NCT05598944, and NCT05775978.

We are currently facing a potential ‘polycrisis’, a critical inflection point that requires a whole-of-society response aimed at building collective foresight and preparedness for short-, medium-, and long-term risks. The role of higher education institutions and social stakeholders is decisive to make an impact. This paper depicts the alignment of academia, governance, and industry with the aim to challenge, inspire, and encourage universities to go beyond commodified courses and mere employability, enhance student growth and bind macro-scale measures that lead to a sustainable future. A modest teaching innovation project has served as a transforming lever, with the private sector joining in, to create a platform that reaches more than 50 000 undergraduate students and teaching staff. The resulting structure, rooted in the University’s strategic plan, has served to channel local and regional initiatives, establish effective partnerships with broad social members, raise awareness and promote actions to advance in the pursuit of Sustainable Development Goals. Chronology, materials and methodology, together with a description of the different courses, programmes and actions are provided. The paper concludes with some recommendations for future research, policy and cooperation among stakeholders. Research methodology posted on clinicaltrials.gov under ID NCT04392869, NCT05598944, and NCT05775978.

Efficient traffic management at signalized intersections is integral to urban infrastructure development, requiring accurate estimation of delay times to mitigate congestion and enhance overall transportation systems. Traditional methodologies, including empirical observations and microsimulation software, have been prevalent in assessing delay times; however, their limitations have prompted the exploration of novel technologies like LiDAR (Light Detection and Ranging) sensors. This research study investigates and compares the accuracy of delay time estimations obtained from LiDAR sensor technology with those derived from microsimulation in AIMSUN. LiDAR sensors, known for their high-resolution, real-time data collection capabilities, offer a promising avenue for precise measurement of delay times at signalized intersections. Nonetheless, challenges in sensor placement, environmental influences, and data processing complexities suggest the need for further development and validation. In parallel, microsimulation software, exemplified by AIMSUN, provides a virtual platform for scenario testing but relies on assumptions that may not always mirror real-world traffic dynamics accurately. The comparative analysis conducted in this study aims to critically examine the discrepancies and potential complementarity between delay times obtained from LiDAR sensor technology and those derived from microsimulation in AIMSUN. The research involves an in-depth evaluation of real-time, high-resolution data collected by LiDAR sensors, assessing their accuracy in capturing the intricate movements and behavior of vehicles at signalized intersections. Simultaneously, AIMSUN microsimulation delay time models are scrutinized for their ability to accurately replicate these observed delay times. The disparities identified serve as critical insights into the challenges of both methodologies, prompting the discussion on the prospects of integrating LiDAR-derived data and microsimulation calibration processes to enhance the precision and reliability of delay time estimations. Future traffic management strategies can significantly benefit from a more accurate understanding of delay times, and this study endeavors to contribute to the advancement of methodologies in traffic engineering for more effective urban transportation systems.The paper's findings illuminate the potential and limitations of both LiDAR sensor technology and microsimulation in estimating delay times at signalized intersections. The results highlighted that the LiDAR sensors could accurately calculate delay times at a signalized intersection. Furthermore, the calculated delay time differences by LiDAR and AIMSUN at three days with the highest vehicle volumes (counts) are always less than 6.5%.

Addressing the significant challenge in high-speed cotton dibbling operations in Xinjiang—specifically, the duck bill’s ("Duck bill" is a type of duck-billed bunch planting mechanism or component). shortened opening duration leading to seed throwing and floating—a new crawler-type delayed hole-forming mechanism has been designed. This mechanism extends the duck bill horizontally, thereby prolonging its opening time, enabling cotton sowing speeds of up to 6 km/h. Following agronomic principles for cotton planting, the overall layout of the crawler-type hole-forming mechanism, the structural parameters of the key components and the trajectory of the hole-forming are determined. We use the Discrete Element Method (DEM) and multi-body dynamics coupling method to simulate and analyze the motion process of the device. The fixed the tilt angle of the duck bill α(A), the depth of the duck bill hole-forming into the soil h(B), and the angle of rotation of the moving duck bill β(C) were taken as the experimental factors, with the longitudinal length of cotton seed hole (Y1) and the hole-forming depth of cotton seed hole (Y2) as the response values. The parameter range of each factor and the preliminary influence on the response value were determined through pre-experiments and single-factor simulation test. Based on RecurDyn-EDEM coupling, a quadratic regression orthogonal rotation combination simulation test was carried out. The results show that the order of the primary and secondary factors affecting the Y1 of the time-lapse hole-forming device was: A > C > B. The order of primary and secondary factors affecting the Y2 of the delayed hole forming device was: B > C > A. When the A was 2.4 °, the B was 42.4 mm, and the C was 30.5 °, the performance of the hole-forming was the best, and the Y1 was 26.4 mm, and the Y2 was 25.0 mm. The bench verification test results show that under the optimized combination of operating parameters, the average Y1 was 29.1 mm, and the average Y2 was 23.2 mm. Compared with the results of the previous coupled simulation model, the average relative errors of the two are 7.23 % and 4.36 %, respectively, indicating the accuracy and effectiveness of the established DEM simulation model and virtual test analysis. The hole-forming area and the opening time of the duck bill after the stable operation of the machine were recorded and measured. The calculated hole dislocation rate Hc was 4.33 %, which did not exceed the national standard requirement of 6 %. The qualified rate of hole distance Hx was 94.33 %, which was much higher than the national standard requirement of 80 %. The average opening time of the duck bill at a speed of 6 km/h is 0.45 s, which is much longer than the time required for cotton seeds to fall from the duck bill 0.11 s. It meets the requirements of high-speed cotton planting in China and facilitating advancements in future high-speed planter technology.

Delay Tolerant Networks (DTNs) are intermittently connected networks, where there is no guaranteed end-to-end connectivity between the source and destination. The link between the pair of nodes in the DTNs environments is frequently disrupted, due to the fast mobility of nodes, dissemination nature, and power outages. Due to the absence of contemporaneous paths between the nodes, the opportunities for message forwarding in DTNs usually are limited. To obtain high data delivery, the DTNs use innovation of the Store-Carry and Forward (SCF) technique which allows data transmission to successfully proceed despite the absence of continuous end-to-end paths. However, the SCF approach arises various issues such as buffer congestion and message drop which are caused due to growing number of carried messages in restricted network resources. Therefore, buffer management techniques are required to manage the buffer capacity of the nodes by deciding how to effectively drop the messages and how to schedule the messages in the node’s buffer in a perfect way. This paper evaluates the performance of six buffer management techniques, namely First-In-FirstOut, Last In First Out, Drop Largest, Drop Youngest, Evict Shortest Lifetime First and Evict Most Forwarded First, with MaxProp and Spray and Wait routing protocols under variable message’s Time-To-Live values (60 to 300 minutes with step-change 60 minutes). In addition, this study uses an Opportunistic Network Environment (ONE) simulator that is utilized for evaluating the performance of the dropping policies techniques, where it is considering five performance metrics (delivery ratio, overhead ratio, average latency, hop count, and message drop). The evaluation results of each buffer management policy are explained by these metrics briefly.

We analyze a time-delayed SIQR model that considers the transportation-related infections and entry-exit screening. This model aims to determine the measures for preventing and controlling major emergent infectious diseases and the associated costs. We calculate the basic reproduction number (R0), apply the linearization method, and construct an appropriate Lyapunov function to determine the stability of the disease-free equilibrium in the local and global. We collect COVID-19 infection data from two regions in the United States in 2020 for data fitting, obtain a set of optimal parameter values, and show that the model is suitable for simulating the outbreak and spread of emerging infectious diseases. We find that transportation-related infections increase the basic reproduction number, enhancing the impact on disease spread. Entry-exit screening effectively suppress the spread of disease by reducing the basic reproduction number. Furthermore, we investigate the influence of the incubation period on disease and find that a shorter incubation period results in a shorter duration but a larger scale of infection, and the peaks are reduced. We conduct a sensitivity analysis of the R0 and propose three measures to prevent the spread of new infectious diseases based on the most sensitive parameters: wearing masks, implementing urban closures, and administering medication to sick but not yet hospitalized patients promptly. In the case of COVID-19, we use Pontryagin’s minimum principle to get time-varying control measures to control the spread of the outbreak. Optimal control effectively controls the development and deterioration of the disease. Finally, several control measures are compared through cost-effectiveness analysis, and the results show that wearing masks is the most cost-effective measure. Our study provides some practical guidance for controlling the spread of major emerging infectious diseases.

We address the dynamics of two-dimensional Navier-Stokes models with infinite delay and hereditary memory, whose kernels are a much larger class of functions than the one considered in the literature, on a bounded domain. We prove the existence and uniqueness of weak solutions by means of Faedo-Galerkin method. Moreover, we establish the existence of global attractor for the system with the existence of a bounded absorbing set and asymptotic compact property.

Due to the advantages such as low power consumption and higher concealment, deceptive jamming against synthetic aperture radar (SAR) receives extensive attention during the past decades. However, the large scene deception jamming is still a challenge because of the huge computing burden. In this paper, we propose a new large scene deceptive jamming algorithm. First, the time-delay and frequency-shift (TDFS) algorithm is introduced to improve the jamming processing speed. The system function of jammer (JSF) for a fake scatter is simplified to the multiplication of the scattering coefficient, a time-delay term in range dimension and a frequency-shift term in azimuth dimension. Then, in order to solve the problem that the effective region of the TDFS algorithm is limited, the scene deceptive jamming template is divided into several blocks according to the SAR parameters and imaging quality control factor. The JSF of each block is calculated by the TDFS algorithm and added together to achieve the large scene jamming. Finally, the correction algorithm in squint mode is derived. The simplification and parallel block processing could improve the calculation efficiency significantly. The simulation results verified the validity of the algorithm.

We consider the financial planning problem of a retiree wishing to enter a retirement village at a future uncertain date. The date of entry is determined by the retiree's utility and bequest maximisation problem within the context of uncertain future health states. In addition, the retiree must choose optimal consumption, investment, bequest and purchase of insurance products prior to her full annuitisation on entry to the retirement village. A hyperbolic absolute risk-aversion (HARA) utility function is used to allow necessary consumption for basic living and medical costs. The retirement village will typically require an initial deposit upon entry. This threshold wealth requirement leads to exercising the replication of an American put option at the uncertain stopping time. From our numerical results, active insurance and annuity markets are shown to be a critical aspect in retirement planning.

The present study aims at investigating the relationship between Initial Public Offerings (IPOs) variables mainly underpricing on one hand, and the brand value measures on the other. Our final data set is 104 international brand companies. We implement empirical approach using hierarchical OLS regression and descriptive statistics. We show that underpricing is positively related to brand value which emphasizes the marketing role of going public and underpricing in enhancing brand equity through the product market, which additionally confirms some information asymmetry models. We also find that on average brand companies had not been recognized as brands at the IPO time. Moreover, we show the positive role of private equity in enhancing brand value, additionally, the non-linear association between underpricing and brand value is not evident. Finally, we draw some policy implication and suggestions for future research.

The group delay response of chirped fiber Bragg gratings (CFBG) written in polarization-maintaining fiber can be measured using the beat spectrum of the reflections from the two polarization axis, with a resolution and reproducibility better than 50 fs. The method is theoretically described, and we analyze the effect of group delay ripples (GDR) on the performance of a stretcher-compressor pair used in chirped pulse amplification systems. Ripples with a spectral period of the order of the pulse bandwidth are the most deleterious. Those are readily captured with our method, despite the limit on resolution due to the fiber polarization beat length. As a rule of thumb, the GDR should not exceed half the pulse duration. The reconstructed phase of the CFBG is also used to predict the pulse compression performance for a given device. Measurement of GDR as low as 161 fs is experimentally demonstrated.

Several pathotypes of enteric E. coli have been identified. The group represented by Shiga toxin-producing E. coli (STEC) is of particular interest. Raw milk and raw milk products are significant sources of STEC infection in humans; therefore, identifying pathogens at the herd level is crucial for public health. Most national surveillance programs focus solely on raw milk and raw milk cheeses that are ready for retail sale, neglecting the possibility of evaluating the source of contamination directly at the beginning of the dairy chain. In order to assess the viability of new molecular methodologies applied to raw milk filters enabling the identification of the presence of STEC serotypes in milk production and apply the same methods to identify the presence of these pathogens in calf feces we analyzed, through a commercial real-time PCR assay, a total of 290 samples coming from 18 different dairy herds; 88 bulk tank milk (BTM), 104 raw milk filters (RMF) and 98 calves’ feces samples. In total 3.4% of BTM, 41.4% of RMF and 73.4% of calves’ feces tested positive for stx presence, supporting our hypothesis that BTM is not a suitable matrix to assess the STEC presence at herd level, underestimating it. Our conclusion is that the surveillance program needs critical and extensive improvements such as RMF and calves’ feces analysis implementation in order to be more efficient in detecting and preventing STEC infections. The epidemiology of these infections and the characteristics of the pathogen clearly show how a One Health approach will be pivotal to improve our capabilities to control the spread of these infections.

The advent of deep learning (DL) has revolutionized medical imaging, offering unprecedented avenues for accurate disease classification and diagnosis. DL models have shown remarkable promise for classifying brain tumor from Magnetic Resonance Imaging (MRI) scans. However, despite their impressive performance, the opaque nature of DL models poses challenges in understanding their decision-making processes, particularly crucial in medical contexts where interpretability is essential. This paper explores the intersection of medical image analysis and DL interpretability, aiming to elucidate the decision-making rationale of DL models in brain tumor classification. Leveraging state-of-the-art DL frameworks with transfer learning, we conduct a comprehensive evaluation encompassing both classification accuracy and interpretability. Using state-of-the-art DL frameworks with transfer learning, we conduct a thorough evaluation covering both classification accuracy and interpretability. We employ adaptive path-based techniques to understand the underlying decision-making mechanisms of these models. Grad-CAM and Grad-CAM++ highlight critical image regions where the tumors are located.

In this paper, we study the problem of controllability of impulsive neutral evolution integrodifferential equations with state dependent delay in Banach spaces. The main results are completely new and are obtained by using Sadovskii's fixed point theorem, theory of resolvent operators, and an abstract phase space. An example is given to illustrate the theory.

This work compared the performance of three methods for constructing a regional ensemble prediction system (EPS) for wind speed forecasts: dynamical downscaling, breeding of growth modes (BGM), and blending method. The Weather Research and Forecasting (WRF) model was used to downscale the European Centre for Medium-range Weather Forecast (ECMWF) EPS. In addition, as the BGM method needs observation data for generating scaling factors, an alternative method for generating scaling factors was proposed to eliminate dependence on observation data. One-month tests between October 1st and October 30th, 2020, were implemented to evaluate the performance of three methods in the Gansu province of China. The results demonstrate that the blending method outperforms the other two methods. Furthermore, the difference in performance is evident mainly in early forecast lead time and becomes negligible as forecast time increases.

It is becoming clear that in addition to gap junctions, playing a role in cell-cell communication, gap junction proteins, connexins, located in cytoplasmic-compartments may have other important functions. Mitochondrial connexin 43 (Cx43) is increased after ischemic preconditioning and has been suggested to play a protective role in the heart. How Cx43 traffics to the mitochondria and the interactions of mitochondria with other Cx43-containing structures are unknown. In this study, immunocytochemical, super-resolution and transmission electron microscopy were used to detect cytoplasmic Cx43-containing structure and to demonstrate their interactions with other cytoplasmic organelles. The most prominent cytoplasmic Cx43-containing structures, annular gap junctions, were demonstrated to form intimate associations with lysosomes as well as with mitochondria. Surprisingly, the frequency of associations between mitochondria and annular gap junctions was greater than that between lysosomes and annular gap junctions. The benefits of annular gap junction/mitochondrial associations are not known. However, it is tempting to suggest that the contact between annular gap junction vesicles and mitochondria facilitates Cx43 deliver to the mitochondria. Furthermore, it points to the need for investigating trafficking of Cx43 to cytoplasmic compartments and annular gap junction as more than only a vesicle destined for degradation.

This paper investigates the influence of magnetic field for a two dimensional deformations on a two temperature problem at the free surface of a semi-infinite semiconducting medium under the effect of mechanical force during a photothermal theory and the effect of hydrostatic initial stress on the medium. The Harmonic Wave Method (Normal Mode Analysis) has been used to obtain the equations of elastic waves, heat conduction equation, quasi-static electric field, carrier density, two temperature coefficient, ratios, and constitutive relationships for the thermo-magnetic-electric medium. The effects of several parameters as thermoelastic and thermoelectric coupling parameters and two temperature parameter of this force on the displacement component, force stress, carrier density and temperature distribution has been depicted graphically.

Sharding shows great potential for extending the blockchain. The current challenge facing sharded blockchain technology lies in addressing the extended transaction confirmation times caused by isolated states between shards and unbalanced transaction allocation strategies. These factors contribute to an increase in cross-shard transactions and disproportionate shard workload, ultimately resulting in indefinite confirmation delays for cross-shard transactions. A critical priority for sharded blockchain systems is to conduct a comprehensive qualitative analysis to better understand and mitigate the prolonged transaction confirmation times. We introduce a Product-Form Queue Network (PFQN) model to address the transaction confirmation time problem in sharded blockchains and incorporate a new confirmation queue to more accurately simulate the actual transaction confirmation process in the blockchain. In addition, we provide a detailed quantitative analysis of the relationship between network load, consensus efficiency, and security in sharded blockchains, laying a theoretical foundation for achieving robustness and efficiency in sharded blockchains. This research not only contributes to addressing the scalability issues in sharded blockchains but also offers a new perspective for future research directions.

The necessity for precise and current data concerning the dynamics of land cover change in Indonesia is crucial for efforts to reduce natural vegetation cover due to agricultural expansion. The functionality of monitoring systems that incorporate Terra-MODIS is currently compromised by the limited availability of data for the immediate future. This study seeks to assess the potential of VIIRS satellite imagery in developing an early warning system for monitoring vegetation cover change in Indonesia. The Normalized Differential Open Area Index (NDOAI) computed from the 8-day’ VIIRS data was employed to detect changes in vegetation cover based on pixel-by-pixel subtraction in the NDOAI data time series. Evaluating the pixel-level accuracy of change detection is complicated due to the fact that we evaluate a change map at a coarser resolution than the Landsat-based reference map. The results revealed that increasing the threshold percentage is associated with improved accuracy. In change detection, there is often a trade-off between accuracy and sensitivity. A threshold that is too low may result in false positives, while a threshold that is too high may lead to missed changes. This study demonstrates that when a threshold value of less than 20% is applied, Landsat can identify vegetation cover changes at an earlier stage. Conversely, when a threshold value greater than 20% is employed, VIIRS will detect the change 4.5 days earlier than Landsat. Additionally, VIIRS is capable of detecting changes 25.4 days and 54.8 days faster than Landsat, respectively, when using thresholds of 40% and 75%.

This paper proposed an optimal tracking control scheme through adaptive dynamic programming(ADP) for a class of partially unknown discrete-time nonlinear systems based on radial basis function neural network(RBF-NN). In order to acquire the unknown system dynamics, we use two RBF-NNs, the one is used to construct the identifier, and the another is used to directly approximate the steady-state control input, where a novel adaptive law is proposed to update neural network weights. While the optimal feedback control and the cost function are derived via feedforward neural networks approximating, it is proposed to regulate the tracking error, the critic network and the actor network are then trained online to obtain the solution of the associated Hamilton–Jacobi–Bellman (HJB) equation being built under the ADP framework. Simulations verify the effectiveness of the optimal tracking control technique using the neural networks.

Spatio-Temporal Dynamic Mode Decomposition (STDMD) is an extension of Dynamic Mode Decomposition (DMD) designed to handle spatio-temporal datasets. It extends the framework so that it can analyze data that has both spatial and temporal variations, allowing for the extraction of spatial structures and their temporal evolution. The STDMD method extracts temporal and spatial development information simultaneously, including wavenumber, frequencies and growth rates, which is essential in complex dynamic systems. We provide a comprehensive mathematical framework for sequential and parallel STDMD approaches. We also introduce delay coordinates generalization to the presented algorithms to extend the scope of their application. The extension, labeled delay embedding STDMD allows the use of delayed data, which can be both time-delayed and space-delayed. An explicit expression of the presented algorithms in matrix form is also provided, which facilitates theoretical analysis and provides a solid foundation for further research and development. The novel approach is demonstrated using some illustrative model dynamics.

Quantum gravity theories rely on a minimal measurable length for their formulations, which clashes with the classical formulation of the uncertainty principle and with Lorentz invariance from general relativity. These incompatibilities led to the development of the generalized uncertainty principle (GUP) from string theories and its various modifications. GUP and covariant formulations of the uncertainty principle are discussed, together with implications for space-time quantization.

Space instable target simulator (SITS) is a vital actuator for ground verification of on-orbital capture technology, the motion performance of which directly affects simulation credibility. Different delays reduce the stability of SITS and ultimately lead to its divergence. In order to achieve high fidelity simulation, the impact of force measurement delay, discrete control cycle, and simulator response delay on stability is analyzed firstly. Then, the dynamic equation and transfer function identification model of hybrid simulator is constructed, and the necessary and sufficient conditions of its stability and convergence are obtained using the Routh criterion. After that, a switching compensator with variable gain is proposed, the compensation principle diagram of which is build, and its mathematical model including the energy observer and tracking differentiator is also established. Finally, three sets of numerical simulations are conducted to validate the correctness of the stability analysis and effectiveness of proposed compensation method. Simulation results show that all three types of delay can cause SITS to lose stability under critical stable motion state, and the delay in force measurement has the greatest impact, followed by the influence of control cycle. Compared with the force applied to simulated target, velocity and its recovery coefficient of space instable target using fixed gain and linear gain compensation, the proposed compensator has significantly better performance.

In the field of railroad safety, effective detection of surface cracks is critical, necessitating reliable, high-speed non-destructive testing (NDT) methods. This study introduces a hybrid Eddy Current Testing (ECT) probe, specifically engineered for railroad inspection, to address the common issue of ’lift-off noise’ due to varying distances between the probe and test material. Unlike traditional ECT methods, this probe integrates transmit and differential receiver coils, aiming to enhance detection sensitivity and minimize lift-off impact. The study optimizes ECT probes employing different driver coils, emphasizing three main objectives: a) quantitatively evaluating each probe using signal- to-noise ratio (SNR) and outlining a real-time data processing algorithm based on SNR methodology; b) exploring the frequency range proximal to the electrical resonance of the receiver coil; c) examining sensitivity variations across varying lift-off distances. The experimental outcomes indicate that the newly designed probe with figure 8-shape driver coil significantly improves sensitivity in detecting surface cracks on railroads. It achieves an impressive SNR exceeding 100 for defects with minimal dimensions of 1 mm in width and depth. Simulation results closely align with experimental findings, validating the investigation of optimal operational frequency and lift-off distance for selected probe performance, determined to be 0.3 MHz and 0.5 mm, respectively. The realization of this project would lead to notable advancements in enhancing railroad safety by improving crack detection efficiency.

As the adoption of renewable energy sources grows, ensuring a stable power balance across various time frames has become a central challenge for modern power systems. In line with the "dual carbon" objectives and the seamless integration of renewable energy sources, harnessing the advantages of various energy storage resources and coordinating the operation of long-term and short-term storage have become pivotal directions for future energy storage deployment. To address the complexities arising from the coupling of different time scales in optimizing energy storage capacity, this paper proposes a method for energy storage planning that accounts for power imbalance risks across multiple time scales. Initially, the Seasonal and Trend decomposition using the Loess (STL) decomposition method is utilized to temporally decouple actual operational data. Subsequently, power balance computations are performed based on the obtained data at various time scales to optimize the allocation of different types of energy storage capacities and assess the associated imbalance risks. Finally, the effectiveness of the proposed approach is validated through hourly applications using real-world data from a province in China over recent years.

A given problem in physics can be solved if it is well formulated. Well formulated means that it has a bijective correspondence to physical reality. Mass Gap Problem has no bijective correspondence with the physical reality and is that’s why not solvable mathematically. It can be solved in the frame of quantum mechanics by the formulation of the photon’s mass accordingly to the Planck-Einstein relation.

Performing optimisation and scale-up studies of crystallisation systems requires accurate and computationally efficient mathematical models. The assumption of the ideal mixing conditions in batch reactors typically produce inaccurate results while the computational expense of CFD models is still prohibitively high. Therefore, in this work, a new intermediary approach is proposed that takes into account the non-ideal mixing conditions in the reactor and requires less computational resources than full CFD simulations. Starting with the Danckwerts concept of the intensity of segregation, an analogy between its application to chemical reactions and the kinetics of the crystallisation phenomena (such as nucleation and growth) has been made. As a result, the modified kinetics expressions have been derived which incorporate the effect of non-idealities present in stirred reactors. This way, based on the experimental measurements of the mixing time using the Laser Induced Fluorescence (LIF) technique, computationally more efficient mathematical models can be developed in two ways: (1) the accurate semi-empirical correlations are available for standard mixing configurations with the most often used types of impellers, (2) CFD simulations can be utilised for estimation of the mixing time; in this case it is necessary to simulate only the mixing process. The benefits offered by the LIF experimental technique have been demonstrated and some frequent problems in its application analysed. The mixing time results for configurations with and without baffles for three types of impellers and four different rotational speeds have been presented. The false shorter mixing times in the non-baffled configurations have been observed and this phenomena explained by the existence of two segregated zones in the reactor and confirmed by additional experiments. The precise measurements in these cases have been shown as difficult using the LIF technique, particularly for higher rpms. The experimental data has been compared to the preliminary simulation results obtained from the Smoothed Particle Hydrodynamics method and the standard k-ε turbulence model with the modest success. The shortcomings of the SPH model have been recognized and the directions for the future work discussed.

The main purpose of this paper is to present a comprehensive view of the application mathematical models in the designing and implementing SSCM beside to solving problems and making decision. The research questions are: what mathematical models are used for designing and implementing sustainable supply chain management, how to use them, which industries implemented in, what modules of SSCM depth in and finally finding the gaps of researches. The methodology of research is Systematic Literature review through peer review papers which are published in high ranking journals. In this paper, First, we search all papers through scientific data bases like Scopus, science direct, MDPI, Springer, Google Scholar, then, screening papers based on the criteria such as subject of paper, journals impact factor which is published in-should be peer review journal- and relative content of the papers. Finally, we selected 245 papers with three steps screening through 2806 papers that they have enough quality and relative to our research goals for context analysis. Through context analysis, first we categorized the information of the papers and drew the current situation of researches in the framework of our topic. Then, we evaluate and compare the goals of sustainability and current situation and found the gapes, then, offered new suggestions like implementing SSCMs models in pollutant industries like casting industry, Heavy industry, coal Industry and so on. On the other hand, there are gaps in researches in some modules of SSCM such as packaging, designing products, etc.

The aim of the present study is to investigate both the performance and preferences of males and females Computer Science (CS) graduates. In order to attain the above goal, a quantitative case study was conducted regarding 89 degrees, acquired from 2006 to 2012, from the Department of Computer Science and Technology, University of Peloponnese, Greece. The analysis of the data revealed that in terms of performance, no significant differences between the mean grades of males and females exist, in almost most of the courses included in the curriculum of the aforementioned CS department. Any statistically significant differences in performances were present in almost equal number of courses in favor of males and females. It seems also, that females performed better in the courses they selected more than males. Regarding preferences, in CS courses, it seems that gender differences are existent. Males preferred more than females did core programming courses and advanced topics of Software Systems, computer networks, computer engineering, robotics and mathematics, whereas females preferred more the study of algorithms and security issues, computer fractals, data management, computer architecture, and mobile communication. In addition, females preferred courses in reference with humanities and social sciences, CS terminology, and career opportunities. Yet, females did not select any of programming lab-based courses, computer engineering, computer network issues and robotics.

Abscisic acid (ABA) plays a major role in promoting ripening in sweet cherry, a non-climateric fruit. Exogenous application of ABA has been performed to study fruit ripening and cracking, but this growth regulator is not used for commercial production. To determine the potential of this growth regulator to improve sweet cherry fruit quality, ABA canopy spraying was assayed in four cultivars. Canopy spraying of S-ABA significantly: 1) enhanced sweet cherry fruit color in ‘Glenred’, ‘Lapins’ and 'Bing' cultivars, but not in ‘Royal Rainier’ (a bi-colored cultivar), and 2) decreased fruit size and firmness in ‘Lapins’, ‘Bing’ and ‘Royal Rainier’. Seasonally reproducible effects were seen in ‘Lapins’ (mid/late-maturing) but not in ‘Glenred’ (early-maturing). Canopy spraying of nordihydroguaiaretic acid (NDGA) decreased color and increased fruit size in ‘Lapins’, but not in ‘Glenred’. Direct application of ABA on fruits attached to the tree, without application to the foliage, increased Lapins' fruit color without reducing size. These results suggest a localized fruit response to exogenous ABA application on fruit color development, but that a decrease in fruit size may be due to the effects of exogenous ABA on the tree canopy foliage.

In an effort to enhance the efficiency and safety of open-pit mines, this study explores the optimization of end slope road parameters and slope structures, specifically focusing on unmanned driving lanes.A significant aspect of the study is the development of a truck trajectory offset model, which considers the different reaction times between automated sensors and human drivers in adapting to environmental changes. To test these concepts, the study uses numerical simulations to confirm the stability of the proposed end slope designs. Using Victory West Mine No. 1 as a case study, the research determines the optimized width for unmanned driving lanes and the maximum angle for safe steepening of end slopes. The findings indicate that the optimized unmanned lane width for NTE240 mining dump trucks is 1743 mm, allowing for a 2-degree increase in the slope angle at the south end slope. This optimization leads to a steep mining stripping volume of 3.2735 million m³ and a coal output of 2.49628 million tons, maintaining a stripping ratio of 1.31m³/t. These results demonstrate that the unmanned driving road width optimization not only ensures slope safety but also significantly boosts the economic benefits of steep mining in open-pit mines.

Optimal control is a critical tool for mechanical robotic systems, facilitating precise manipulation of dynamic processes. These processes are described through differential equations governed by a control function, addressing a time-optimal problem with bilinear characteristics. Our study utilizes the classical approach complemented by Pontryagin's Maximum Principle (PMP) to explore this inverse optimal problem. The objective is to develop an exact piecewise control function that effectively manages trajectory control while considering the effects of viscous friction. Our simulations demonstrate that the proposed control law markedly diminishes oscillations induced by boundary conditions. This research not only aims to delineate the reachability set but also strives to determine the minimal time required for the process. The findings include an exact analytical solution for the stated control problem.

Initial periods of adsorption kinetics play an important role in estimating the initial adsorption rate and rate constant of adsorption process. Several adsorption processes rapidly occur, and the experimental data of adsorption kinetics under the initial periods can contain potential errors. The pseudo-second-order (PSO) kinetic model has been popularly applied in the field of adsorption. The use of the nonlinear optimization method to obtain the parameters of the PSO model can minimize error functions during modelling compared to the linear method. However, the nonlinear method has limitations in that it cannot directly recognize potential errors in the experimental points of time-dependent adsorption, especially under the initial periods. In this study, for the first time, the different linear types (Types 1–6) of the PSO model are applied to discover the error points under the initial periods. The result indicated that the fitting method using its linear equations (Types 2–5) is really helpful for identifying the error (doubtful) experimental points from the initial periods of adsorption kinetics. The imprecise points lead to low adjusted R2 (adj-R2), high reduced χ2 (red-χ2), and high Bayesian information criterion (BIC) values. After removing those points, the experimental data were adequately fitted with the PSO model. statistical analyses demonstrated that the nonlinear method must be used for modelling the PSO model because its red-χ2 and BIC were lower than the linear method. Type 1 has been extensively applied in the literature because of its very high adj-R2 (0.9999) and its excellent fitting to experimental points. However, its application should be limited because the potential errors from experimental points were not identified by this type. For comparison, the other kinetic models (i.e., pseudo-first-order, pseudo-nth-order, Avrami, and Elovich) are applied. The modelling result using the nonlinear forms of those models indicated that the fault experimental points from the initial periods were not detected.

In this paper, a proof similar to the Pusey-Barrett-Rudolph (PBR) theorem is given to prove that time in quantum theory is not epistemic but has ontological reality. For this, we first discuss how time can be encoded as an intrinsic property of a quantum system. We prepare a quantum state containing time as an intrinsic property and show by a PBR-type proof that time cannot be an epistemic notion. In fact, the PBR theorem implies an ontic notion of time. Indeed, if the quantum state is a physical property, then quantum state reduction is a physical process involving information destruction. In this case, quantum probabilities are intrinsic probabilities without epistemic origin, and they generate a genuinely new sequence of events. This novelty introduced by quantum probabilities can be interpreted as time.

We present a series of computer-assisted high resolution transmission electron (HRTEM) simulations to determine Moiré patters by induced twisting effects between slabs at rotational angles of 3°, 5°, 8°, and 16°, for molybdenum disulfide, graphene, tungsten disulfide, and tungsten selenide layered materials. In order to investigate the electronic structure, a series of numerical simulations using DFT methods was completed using CASTEP with a generalized gradient approximation to determine both band structure and density of states on honeycomb like new superlattices. Our results indicate metallic transitions when rotation approaches 8° with respect to each other for most of the two-dimensional systems that were analyzed.

In this paper, we study the semilinear pseudo-parabolic equations $\displaystyle u_{t} - \triangle_{\mathbb{B}}u - \triangle_{\mathbb{B}}u_{t} = \left|u\right|^{p-1}u$ on a manifold with conical singularity, where $\triangle _{\mathbb{B}}$ is Fuchsian type Laplace operator investigated with totally characteristic degeneracy on the boundary $x_{1} = 0$. Firstly, we discuss the invariant sets and the vacuum isolating behavior of solutions with the help of a family of potential wells. Then, we derive a threshold result of existence and nonexistence of global weak solution: for the low initial energy $J(u_{0})<d$, the solution is global in time with $I(u_{0}) >0$ or $\displaystyle\Vert \nabla_{\mathbb{B}}u_{0}\Vert_{L_{2}^{\frac{n}{2}}(\mathbb{B})} = 0$ and blows up in finite time with $I(u_{0}) < 0$; for the critical initial energy $J(u_{0}) = d$, the solution is global in time with $I(u_{0}) \geq0$ and blows up in finite time with $I(u_{0}) < 0$. The decay estimate of the energy functional for the global solution and the estimates of the lifespan of local solution are also given.

Small molecules that can modulate or stabilize cell-cell interactions are valuable tools for investigating the impact of collective cell behavior on various biological processes such as development/morphogenesis, tissue regeneration and cancer progression. Recently, we showed that budesonide, a glucocorticoid widely used as anti-asthmatic drug, is a potent regulator of stem cell pluripotency. Here we tested the effect of different budesonide derivatives and identified CHD-030498 as a more effective analogue of budesonide. CHD-030498 was able to prevent stem cell pluripotency exit in different cell-based models, including embryonic stem-to-mesenchymal transition, spontaneous differentiation and 3D gastruloid development, and at lower doses compared to budesonide.

The enormous growth in the penetration of electric vehicles (EVs), has laid the path to advancements in the charging infrastructure. Connectivity between charging stations is an essential prerequisite for future EV adoption to alleviate users’ “range anxiety”. The existing charging stations fail to adopt power provision allocation and scheduling management. To improve the existing charging infrastructure data based on real-time information and availability of reserves at charging stations could be uploaded to the users to help them locate the nearest charging station for an EV. This research article focuses on an a interactive user application developed through SQL and PHP platform to allocate the charging slots based on estimated battery parameters, which uses data communication with charging stations to receive the slot availability information. The proposed server-based real-time forecast charging infrastructure avoids waiting times and its scheduling management efficiently prevents the EV from halting on road due to battery drain out. The proposed model is implemented using a low-cost microcontroller and the system etiquette tested.

In this paper, we study a one-dimensional Bresse-Cattaneo system with infinite memories and time-dependent delay term (the coefficient of which is not necessarily positive) in the internal feedbacks. First, it is proved that the system is well-posed by means of the Hille-Yosida theorem under suitable assumptions on the relaxation functions. Then, without any restriction on the speeds of wave propagations, we establish the exponential or general decay result by introducing suitable energy and Lyapunov functionals.

Rheometric investigations facilitate the rheological analysis of cementitious suspensions. However, the choice of the rheometric device and raw data conversion affect the results. Contrary to small gap rheometry, where the flow data shear stress

A remarkable strengths of deep neural networks lies in their ability to discover patterns and representations from complex data. Deep learning models can learn and refine features at different levels of abstraction, enabling them to handle complex tasks in computer vision recognition, natural language processing, and speech recognition. The ability to generalize from examples, coupled with the capacity to process vast amounts of data, empowers deep learning to achieve state-of-the-art results across a wide spectrum of applications. An argument for this ability is based on similarities between deep neural networks and the nervous system. In this report, we argue that despite the remarkable performance of deep learning, there are still gaps between deep learning and the nervous system that needs to be closed to enable deep learning doing tasks that currently only the nervous system can perform

Underwater Sensor Networks (UWSNs) can enable a broad range of applications such as resource monitoring, disaster prevention, and navigation-assisted. It is especially relevant for sensor nodes location in UWSNs. Global Positioning System (GPS) is not suitable for using in UWSNs because of the underwater propagation problems. Hence some localization algorithms based on the precise time synchronization between sensor nodes have been proposed which are not feasible for UWSNs. In this paper, we propose a localization algorithm called Two-Phase Time Synchronization-Free Localization Algorithm (TP-TSFLA). TP-TSFLA contains two phases, namely, range-based estimation phase and range-free evaluation phase. In the first phase, we address a time synchronization-free localization scheme base on the Particle Swarm Optimization (PSO) algorithm to decrease the localization error. In the second phase, we propose a Circle-based Range-Free Localization Algorithm (CRFLA) to locate the unlocalized sensor nodes which cannot obtain the location information through the first phase. In the second phase, sensor nodes which are localized in the first phase act as the new anchor nodes to help realize localization. Hence in this algorithm, we use a small number of mobile beacons to help achieve location without any other anchor nodes. Besides, to improve the precision of the range-free method, an extension of CRFLA by designing a coordinate adjustment scheme is updated. The simulation results show that TP-TSFLA can achieve a relative high localization ratio without time synchronization.

This work introduces a new architecture for a time-domain feedback-based beamformer designed to meet real-time processing demands. The primary goal of this design is to locate reflective sources by estimating their direction of arrival (DOA) and signal range. Incorporating a feedback mechanism in this architecture is a unique aspect that refines localization precision. We conduct an in-depth analysis highlighting their respective benefits and limitations to compare the effectiveness of time-domain feedback beamforming against conventional time-domain methods. Our evaluation of the proposed architecture, based on critical performance indicators such as peak-to-sidelobe ratio, mainlobe width, and directivity factor, demonstrates its ability to improve beamformer effectiveness significantly.

This article develops a multi-perspective view on motivations and methods for tobamovirus purification through the ages, and presents a novel efficient, easy-to-use approach that can be well-adapted to different species of native and functionalized virions. We survey the various driving forces prompting researchers to enrich tobamoviruses: from the search for the causative agents of mosaic diseases in plants to their increasing recognition as versatile nanocarriers in biomedical and engineering applications. Best practice and also rarely applied options for the serial processing steps required for successful isolation of tobamoviruses are then reviewed. Adaptations for distinct particle species, pitfalls and 'forgotten' or underrepresented technologies are considered as well. The article is topped off with our own development of a method for virion preparation, rooted in historical protocols. It combines selective re-solubilization of polyethylene glycol (PEG) virion raw precipitates with density step gradient centrifugation in biocompatible iodixanol formulations, yielding ready-to-use particle suspensions. This newly established protocol and some considerations for perhaps worthwile further developments could serve as putative stepping stones towards preparation procedures appropriate for routine practical uses of the multivalent soft-matter nanorods.

Structural health monitoring has been studied by a number of researchers as well as various industries to keep up with the increasing demand for preventive maintenance routines. This work presents a novel method for reconstruct prompt, informed strain/stress responses at the hot spots of the structures based on strain measurements at remote locations. The structural responses measured from usage monitoring system at available locations are decomposed into modal responses using empirical mode decomposition. Transformation equations based on finite element modeling are derived to extrapolate the modal responses from the measured locations to critical locations where direct sensor measurements are not available. Then, two numerical examples (a two-span beam and a 19956-degree of freedom simplified airfoil) are used to demonstrate the overall reconstruction method. Finally, the present work investigates the effectiveness and accuracy of the method through a set of experiments conducted on an aluminium alloy cantilever beam commonly used in air vehicle and spacecraft. The experiments collect the vibration strain signals of the beam via optical fiber sensors. Reconstruction results are compared with theoretical solutions and a detailed error analysis is also provided.

The reliability of Underwater Wireless Sensor Networks (UWSNs) is measured in terms of energy consumption (EC), end-to-end delay(E2E) and packet delivery ratio (PDR). The adverse effects of channel may cause data loss. Reducing delay up to possible extend improves the reliability of the network, also increasing the number of nodes in a particular network increase reliability. Besides, increasing the number of nodes improve reliability but also increase power consumption. In order to overcome these shortcomings, the two routing protocols are proposed in this paper, namely Delay and Reliability Aware Routing (DRAR) protocol and Cooperative Delay and Reliability Aware Routing (Co-DRAR) protocol for UWSNs. In DRAR protocol, network is divided into two equal regions where two sink nodes(SNs) are positioned at upper region of the network and two SNs are placed at the mid region of the network. The protocol choose the relay node based on residual energy (RE), distance and Bit Error Rate (BER). These parameters protect the data packets from corruption and also provide stable path (where nodes remain active for longer period and do not die quickly). The protocol uses single link and may get worse sometimes while changing channel circumstances. To address this problem, cooperative routing scheme is added to DRAR protocol in order to developed its enhanced version known as Co-DRAR protocol. The protocol works by allowing the destination to receive multiple copies of data packets in order to decide the quality of packets. The proposed protocols DRAR and Co-DRAR perform routing irrespective to geographical position of sensors nodes conversely to the some of conventional routing protocols that's way our propose protocol better perform than the well-known protocol i.e. Depth base routing (DBR) in terms of EC, E2E, PDR, dead nodes, packet drop ratio and number of alive nodes (ANs).

It has been more than a century since Erlang published his paper in 1909. The classical queueing system for the M/D/c queue has been investigated by many authors. The key is to find the roots of an equation using explicit or numerical methods. We present an alternate form of explicit solution(s) of this/these root(s) using the Lambert-W function in this paper. In addition, the unsaturated probabilities of the number of customers in the system is derived explicitly in terms of this/these root(s). Finally, the mean number of customers in the system and the mean queueing delay are obtained from these probabilities. The exact queueing delay formula for the M/D/c queue is expressed in closed-form in terms of the root(s). Numerical results show that they are in excellent agreement with the numerical results published by Seelen, Tijms and Van Hoorn.

This paper presents a study conducted to identify, assess, rank, and compare the most influencing factors causing schedule delay during construction phase of petrochemical projects in Saudi Arabia. The methodology followed in this research to achieve the main aims is a combination of comprehensive review of the literature and interviewing number of local experts, which have resulted in identifying of 23 factors. Through a web-based questionnaire survey, the identified factors were ranked. Total of 90 completed responses were gathered from 106 received responses. The completed responses gathered from 38 contractors and 52 owners. Of 90 participants, there are 32 project managers, 22 project engineers, 7 construction supervisors and the other 31 having different positions in projects departments The study has found that the most influencing factors causing schedule delay during construction in petrochemical projects in Saudi Arabia are “Poor site management and supervision by contractors”; “Conflict between main contractor and subcontractor”; “poor planning and scheduling of projects by contractor”; “Delay of material or equipment delivery”; and followed by “Delay in Handing Over Construction Site to Contractor”. This paper is original in the sense that the areas of knowledge and practice covered in the identified factors were distributed and not available in one source. The factors are derived from personal interviews with selected project managers, project engineers, construction supervisors and the others from different positions in project department and from the relevant literature.

Vocational interest inventories are widely used by career counselors to help individuals to make career choices. The most common approach to assess vocational interests is based on verbal or textual stimuli. However, some of them are based on pictorials to overcome reading limits and provide additional information about the working environment and the activities related to a particular job. This article aims to present two studies on the development and first validation of the Multilingual Iconographic Professional Interest Inventory (MIPII) on two samples, one composed of 792 high-school students, and one composed of 366 middle school students. The inventory aimed to assesses the vocational interests of people over 19 areas by illustrations representing 95 jobs, five for each one, combined with their title in six different languages (Arabic, German, English, Spanish, French and Italian in this order). Both illustrations and titles are provided separately in the male and female version on the same page.

Additive manufacturing (AM) provides opportunities to design objects differently than traditional manufacturing methods allow, but only if designers understand the possibilities AM presents. In this study, we examined whether an AM workshop combined with an idea generation session could inspire engineering professionals to use AM solutions to solve current technical problems they face. All subjects were employees at an organization that will be referred to as Company X, a multinational commercial organization based in North America. During the study, we collected ideas for 24 projects generated before and after a training workshop focused on design for AM. In the workshop, we provided three hours of instruction about design for two metal-based AM processes. The participants’ ideas were assessed using four specific metrics: (1) cost, (2) time,(3) completeness of solution, and (4) quality, which was a function of feasibility, usefulness, and novelty. Using these data, we explored whether the workshop was effective in inspiring the participants to use AM methods and techniques from AM research in their concept generation and whether participants’ AM solutions showed improvement in cost, implementation time, and quality over non-AM designs generated before the workshop.

Enforcement of animal welfare statutes are the primary protection given for the maintenance of animal welfare and prevention of cruelty. It is speculated that animal law enforcement in Australia has a number of weakness in the enforcement model. These weaknesses create a gap between the goals of animal law enforcement and the reality of the animal law justice system. This gap is defined as the ‘enforcement gap’. This paper identifies and investigates the causes of this gap. The hypothesized causes discussed are (1) the impact the public can have on reporting animal cruelty, (2) the reliance on charitable organizations as enforcement bodies, (3) the inconsistencies in animal welfare legislation, and (4) the role of the sentencing courts. Thus, the causes of the enforcement gap are multifactorial; derived from all stages of the enforcement process. Further research is needed to investigate the concepts raised in this paper. However, it is likely that a combination of structural change to enforcement agencies, legislative reform and public education is required to reduce the enforcement gap.

This study aimed to evaluate the effects of Blazepod technology when incorporated with various training regimens on the essential elements of physical fitness in volleyball, such as agility, speed, visual response time, and vertical leap. Thirty-six participants (age :17.33±0.48 y, height: 183.78±6.34 cm, weight: 77.14±5.16 kg) were in-volved in this study. In randomized design, three equal groups with two experimental groups and one control group were involved in the study over a period of six weeks: (GE1) used Blazepod technology to workout at a low level; (GE2) used Blazepod technology to workout at a higher intensity; (CG) did not employ Blazepod technology, but it adhered to the same fundamental training curriculum. We conducted agility, speed, reaction time, and vertical jump tests before, midway and after the study to determine optimal training volume, intensity, and frequency. A significant main effect of time (P0.01), and time×group interaction (P>0.001) were found for all tests. Post hoc test showed that the two experimental groups gadget significantly improved in all performance variables (P

We review time expansion wave theory and refine our model showing it to accurately match observed cosmological luminosity data. The theory augments general relativity to create a container within which quantum effects can be explained by treating time as an artefact of a fourth spatial dimension that we observe as the expansion of the universe. This leads us to explain mass creation, the speed of light limit, gravity, black holes without singularities and other macroscopic effects. Our model leads to an expansion velocity of 6.87 0.36 × 106 ms-1, which results in a Hubble expansion rate constant of 71.3 3.7 km/s/Mpc. Because of the finite window of time in which we exist, an extra a degree of freedom is available leading to interesting interpretations at the subatomic level. At this size range, then a spin is allowed within the time dimension explaining why wave particle duality occurs and explains the electromagnetic force and other quantum mechanical properties. It provides a solution to the double slit conundrum and can explain how quantum entangled partners can behave in a quantum way and pass seemingly time-defying information. The potential quantitative origin of the fine structure constant which governs the size of the electromagnetic force is also strongly indicated by this theory.

In this paper, we study the asymptotic behavior of the sequential empirical process and the sequential empirical copula process, both constructed from residuals of multivariate stochastic volatility models. Applications for the detection of structural changes and specification tests of the distribution of innovations are discussed. It is also shown that if the stochastic volatility matrices are diagonal, which is the case if the univariate time series are estimated separately instead of being jointly estimated, then the empirical copula process behaves as if the innovations were observed; a remarkable property. As a by-product, one also obtains the asymptotic behavior of rank-based measures of dependence applied to residuals of these time series models.

A multiscale model that enables quantitative understanding and prediction of the size effect on scattering properties of micro- and nanostructures is crucial for the design of LED surface textures optimized for high light extraction efficiency (LEE). In this paper, a hybrid process for combining full-wave finite-difference time-domain simulation and a ray-tracing technique based on a bidirectional scattering distribution function model is proposed. We apply this method to study the influence of different pattern sizes of a patterned sapphire substrate on GaN-based LED light extraction from the microscale to the nanoscale. The results show that near-wavelength–scaled patterns with strong diffraction are not expected to enhance LEE. By contrast, microscaled patterns with optical diffusion behavior have the highest LEE at a specific aspect ratio, and subwavelength-scaled patterns that have antireflection properties show marked enhancement of LEE for a wide range of aspect ratios.

This paper proposes an innovative mechatronic piezo-actuated module to control vibrations in modern machine tools. Vibrations represent one of the main issues that compromise seriously the quality of the workpiece. The active vibration control (AVC) device is composed by a host part integrated with sensors and actuators synchronized by a regulator, able to make a self-assessment and adjust to the environmental alteration. This study presents the mechatronic model based on the kinematic and dynamic analysis of the AVC device. To ensure a real time performance, a H2-LQG controller has been developed and validated by simulations involving machine tool, PZT actuator and controller models. The Hardware-in-the-loop (HIL) architecture is adopted to control and attenuate the vibrations. A set of experimental tests has been performed to validate the AVC module on a commercial machine tool. The feasibility of the real time vibration damping is demonstrated and the simulation accuracy is evaluated.

Conflicts are frequent within the complex professional environment of the construction industry. If claims cannot be overcome amicably, they result in disputes that lead to litigation. Identification of the causes of these claims and their impact on the duration, cost, and quality of the final project is expected to facilitate the prevention of unsuccessful performance of construction contracts. The novelty of this study is that after codifying the most common causes of construction contract claims derived from the extant literature, they are further investigated in terms of their probability of occurrence and the perceived impact they have on the project completion time, its total cost, and quality. Based on calculated relative importance indices from expert opinion, this paper proposes probability and severity of impact values for 39 common causes of claims in the construction industry. These can be applied to calculate their risk values for stakeholders in public construction contracts to plan mitigation measures of contractual claims. The findings show that the top five riskiest causes of contractual claims in the Greek construction industry are changes in quantities, work, or scope, design quality deficiencies or errors, payment delays, delays in work progress, and the financial failure of the contractor.

In this study, we deal with a nonlinear system of neutral Volterra integro-differential equations (NVIDEs) with infinite delay. We study stability, uniform stability and instability of zero solution of the system of NVIDEs with infinite delay. We obtain three new results with regard to these concepts via two new Lyapunov– Krasovskii functionals (LKFs), respectively. As the main contributions of this work, we improve and generalize some earlier results in the relevant database from the linear case to more general nonlinear cases.

The global pandemic of COVID-19 accounts for more than 14,000 deaths worldwide. However, little is known about the host genetics interaction with infection and COVID-19 progression. To better understand the role of host genetics, we review the current literature, aggregate readily available genetic resources, and provide some updated analysis relevant to COVID-19 and associated phenotypes. Using the unrelated individuals in UK Biobank (total n = 337,579 across 5 populations), we aggregate human leukocyte antigen and ABO blood type frequencies. We find significant and consistent risk reduction of blood group O reported in Zhao et al. and encourage broad sharing of ABO blood type frequencies that are readily accessible across COVID-19 with mild, moderate, and severe/critical symptoms for robust inferences at https://tinyurl.com/abo-covid19. In addition, we generate polygenic risk scores (PRSs) weights for 29 blood measurements, including clinically relevant haematological measurements for COVID-19, such as lymphocyte count and percentage. Focusing on the 8 most COVID-19 clinically relevant blood measurements, we performed PRS-PheWAS analysis across 44 disease antigen measurements (n = 6,643 unrelated individuals in White British group), infectious diseases and acute respiratory infections (n = 20,928 cases and 349,000 controls across 3 population groups) and deaths (n = 1,846 cases and 368,082 controls), recorded in hospital inpatient record and death registry data, respectively, in UK Biobank, and find host genetic PRS associations with disease risk. Taken together, we anticipate these resources (https://github.com/rivas-lab/covid19) will aid in improving our understanding of host genetic risk factors playing a role in SARS-CoV-2 infection and COVID-19 disease severity.

Accurate prediction of the degree of airport delays under the influence of convective weather is crucial for collaborative traffic management implementation and improving the efficiency of airport operations. However, existing studies usually only consider numerical-type quantitative features of weather-affected traffic in their models, and lack the introduction of spatial information to comprehensively portray the traffic operation scenarios under the influence of weather. In order to overcome this problem, this paper firstly designs a new image representation of weather-affected air traffic, and constructs a multi-channel traffic and weather scene image (MTWSI) by populating the airspace two-dimensional grid with traffic and meteorological information to represent the overall traffic operation situation in the terminal area under the influence of convective weather; then, a deep convolutional neural network-based airport delay prediction model ( ADLCNN), which takes MTWSI images as input and uses a specific CNN model to extract the deep features that affect traffic operation in it to input into the subsequent classification algorithm to predict the flight delay level; finally, a series of comparative experiments are carried out on the operational data of Guangzhou Baiyun Airport, and the experimental validation shows that, compared with the traditional machine learning methods, the proposed CNN-based airport delay prediction The experimental validation shows that the proposed CNN-based airport delay prediction model has satisfactory prediction performance compared with the traditional machine learning methods, which also proves that the proposed MTWSI method can more comprehensively respond to the real traffic conditions.

In this article, we consider the three dimensional $\alpha$-fractional nonlinear delay differential system of the form \begin{align*} D^{\alpha}\left(u(t)\right)&=p(t)g\left(v(\sigma(t))\right),\\D^{\alpha}\left(v(t)\right)&=-q(t)h\left(w(t))\right),\\D^{\alpha}\left(w(t)\right)&=r(t)f\left(u(\tau(t))\right),~ t \geq t_0, \end{align*} where $0 < \alpha \leq 1$, $D^{\alpha}$ denotes the Katugampola fractional derivative of order $\alpha$. We have established some new oscillation criteria of solutions of differential system by using generalized Riccati transformation and inequality technique. The obtained results are illustrated with suitable examples.

One of the biggest challenges in characterizing 2-D image topographies is finding a low-dimensional parameter set that can succinctly describe, not so much image patterns themselves, but the nature of these patterns. The 2-D Cluster Variation Method (CVM), introduced by Kikuchi in 1951, can characterize very local image pattern distributions using configuration variables, identifying nearest-neighbor, next-nearest-neighbor, and triplet configurations. Using the 2-D CVM, we can characterize 2-D topographies using just two parameters; the activation enthalpy and the interaction enthalpy. Initial investigations with two different representative topographies (``scale-free-like'' and ``rich club-like'') produce interesting results when brought to a CVM free energy minimum. Additional phase space investigations, where one of these two parameters has been set to zero, identify useful parameter ranges. Careful comparison of the analytically-predicted configuration variables versus those obtained when performing computational free energy minimization on a 2-D grid show that the computational results differ significantly from the analytic solution. The 2-D CVM can potentially function as a secondary free energy minimization within the hidden layer of a neural network, providing a basis for extending node activations over time and allowing temporal correlation of patterns.

Background: Cancer has been one of the most critical health problems during the past decades which require serious consideration, especially in developing countries. Methods: 80 parents of the children with different types of cancers were studied via both questionnaire and person-to-person interview after announcing their informed consent. Results: The highest delay in patients' initial referral was due to the following factors: lack of attention or ignoring the first symptoms, delay in referring to the physician, low economic status and even lack of family support for the patient. In addition, visiting several doctors after the initial diagnosis, uncertainty about the first proposed method, and high cost of treatment can be mentioned as the main causes of delays in the start of treatment. Conclusion: Education plays an important role in identifying the signs of cancer. In addition, proper relationship and cooperation between the health system and physicians as well as provision of adequate information to patients could lead to the long-term cooperation of these patients in continuing their treatment.

The World Health Organization (WHO) recently added snakebite envenoming to the priority list of Neglected Tropical Diseases (NTD). It is thought that ~75% of mortality following snakebite occurs outside the hospital setting, making the temporal gap between a bite and antivenom administration a major therapeutic challenge. Small molecule therapeutics (SMTs) have been proposed as potential pre-referral treatments for snakebite to help address this gap. Herein, we discuss the characteristics, potential uses and development of SMTs as potential treatments for snakebite envenomation. We focus on SMTs that are secretory phospholipase A2 (sPLA2) inhibitors and metalloprotease (MP) inhibitors.

Background and aim: Human Papillomavirus (HPV) is sexually transmitted, one of the three most common sexually transmitted infections (STIs) in both males and females, and the most common viral STI. A crucial public health strategy to protect people against HPV is through vaccination, which has shown its effectiveness in preventing HPV related diseases. Presently three types of vaccines are available (bivalent, quadrivalent, and nonavalent) and they all target at least the two most oncogenic virus genotypes (HPV 16, 18). In the past few years, the need to implement vaccination programmes that include all genders has been discussed in order to achieve herd immunity against HPV. To date, only a few countries have included young males in their vaccination programmes, so we aim through this review to provide an overview of the epidemiology of HPV and prevention strategies to prevent it, reporting the latest findings from the scientific literature.

Mechanistic models have been used for centuries to describe complex interconnected processes, including biological ones. As the scope of these models has widened, so have their computational demands. This complexity can limit their suitability when running many simulations or when real-time results are required. Surrogate machine learning models can be used to approximate the behaviour of complex mechanistic models, and once built, their computational demands are several orders of magnitude lower. This paper provides an overview of the relevant literature, both from an applicability and a theoretical perspective. For the latter, the paper focuses on the design and training of the underlying machine learning models. Application-wise, we show how machine learning surrogates have been used to approximate different mechanistic models. We present a perspective on how these approaches can be applied to models representing biological processes with potential industrial applications (e.g., metabolism and whole-cell modelling) and show why surrogate machine learning models may hold the key to making the simulation of complex biological models possible using a typical desktop computer.

In this short communication, we conducted first-principles calculations to explore the stability of boron monochalcogenides (BX, X=S, Se or Te), as a new class of two-dimensional (2D) materials. We predicted BX monolayers with two different atomic stacking sequences of ABBA and ABBC, referred in this work to 2H and 1T, respectively. Analysis of phonon dispersions confirm the dynamical stability of BX nanosheets with the both 2H and 1T atomic lattices. Ab-initio molecular dynamics simulations reveal the outstanding thermal stability of all predicted monolayers at high temperatures over 1500 K. BX structures were found to exhibit high elastic modulus and tensile strengths. It was found that BS and BTe nanosheets can show high stretchability, comparable to that of the graphene. It was found that all predicted monolayers exhibit semiconducting electronic character, in which 2H structures present lower band-gaps as compared with 1T lattices. The band-gap values were found to decrease from BS to BTe. According to the HSE06 results, 1T-BS and 2H-BTe show respectively, the maximum (4.0 eV) and minimum (2.06 eV) electronic band-gaps. This investigation introduces boron monochalcogenides as a novel class of 2D semiconductors with remarkable thermal, dynamical and mechanical stability.

A time-sequential working, spatially multiplexed autostereoscopic 3D display design consisting of a fast switchable RGB-color filter array is presented. The wavelength-selective filter barrier emits the light from a display over a larger active area than common autostereoscopic barrier displays. An optical modelling of wavelength-selective barriers has been used for instance to calculate the light ray distribution properties of that arrangement. To find well working display designs, automated searches by simulation and computational evaluation has been proceeded. Wavelength-selective filter barrier arrangements exhibit characteristics different from common barrier displays with similar barrier pitch and ascent. In particular, these constructions show strong angular luminance dependency under barrier inclination specified by correspondent slant angle. In time-sequential implementation it is important to avoid that quick eye or eyelid movement lead to visible color artifacts. In the millisecond regime tunable liquid crystal Fabry-Pérot color filters for the colors red, green and blue are presented. They consist of a sub-micrometer thick nematic layer sandwiched between dielectric mirrors and ITO-electrodes. These cells shall switch narrow-banding light of red, green or blue. An array for a glasses-free 3D display has to be equipped with several thousand switchable filter elements having different color apertures. The newly introduced design is usable as a multi user display as well as a single user system with user adaptive control.

When dealing with limited sample sizes or missing values in time series data, achieving high accuracy in forecasting becomes challenging. This challenge is particularly common in wind energy forecasting, where many wind farms lack complete data. In this paper, we employ the widely-used ARIMA (Autoregressive Integrated Moving Average) model for time series forecasting. To address the difficulties posed by limited sample sizes and missing values, we adopt a unique approach by utilizing multiple ARIMA models for different datasets. A key distinction from other multiple models methods for time series forecasting lies in each model within our approach using its own dataset, making the fusion process more intricate. To overcome this, we incorporate neural networks and two techniques for model fusion: direct fusion with a learning mechanism and compensation for missing data through training. For each ARIMA model, we introduce a noise estimation method to circumvent the white noise assumptions inherent in ARIMA models. Finally, we apply these methods to wind energy prediction, and our experimental results showcase a significant enhancement in forecasting accuracy.

This paper investigates the feasibility of a backend design for real-time, multiple-channel processing digital phased array system, particularly for high-performance embedded computing platforms constructed of using general purpose digital signal processors. Frist, we obtained the lab-scale backend performance benchmark from simulating beamforming, pulse compression, and Doppler filtering based on MicroTCA chassis using Serial RapidIO protocol in backplane communication. Next, a field-scale demonstrator of a multifunctional phased array radar is emulated by using the similar configuration. Interestingly, the performance of a barebone design is compared to that of emerging tools that systematically take advantage of parallelism and multicore capabilities, including Open Computing Language.

Obesity poses significant challenges in rural communities worldwide due to limited resources and healthcare access. Practical, innovative, and culturally sensitive approaches are essential. Time-Restricted Eating (TRE), aligning food intake with circadian rhythms, emerges as a promising strategy. By restricting eating to specific time windows, TRE synchronizes with the body's internal clock, offering potential metabolic health benefits. This review examines TRE's potential in rural obesity management, highlighting its simplicity and scalability. While TRE may address rural health disparities, cultural considerations and challenges such as undernutrition must be acknowledged for effective implementation. Overall, TRE shows promise in improving metabolic health and well-being in rural populations.

Psychomotor developmental delay in infants includes failure to acquire abilities such as sitting, walking, grasping objects and communication at the ages when most infants have acquired these abilities. Known risk factors include a large number of aspects of family environment, socioeconomic position, problems in pregnancy and birth, and maternal health. It is clinically useful to be able to screen for developmental delay so that healthcare interventions can be considered. The present research used machine learning (random forest) to create an algorithm predicting psychomotor delay in 9-month-old infants using information ascertainable at birth and in early infancy. The dataset was the UK longitudinal Millennium Cohort study. Fifty-two predictors measuring socioeconomic indicators, paternal, family and social support for the mother, beliefs about good parenting, maternal health, pregnancy and birth were included in the initial algorithm. Feature reduction showed that of the 52 variables, birthweight, family income and parents’ ages had the highest feature importance scores and could alone correctly predict developmental delay with over 99% sensitivity and 100% specificity. The relationships between delay and some of the predictors, particularly income, were nonlinear and complex. The results suggest that the risk of psychomotor developmental delay can be identified in early infancy using machine learning, and that the best predictors are factors present prior to birth. Surprisingly, the most important factors included in the present study did not include illnesses during pregnancy such as eclampsia and infections.

In modern Commercial Off-The-Shelf (COTS) multicore systems, cores can produce several simultaneous memory requests. The processing of such requests over the memory controller negatively impacts the interference delay triggered by running parallel tasks on the platform. In this paper, we propose a software-based testing approach for analyzing memory interference delay, when cores are exposed to extensive read/write requests that access in parallel their Cache Coherent Interconnect. The hardware targeted in this work is the well-known LayerScape QorIQ LS2085A, which can be approached as a potential successor to the Freescale QorIQ P4080. The test analysis was conducted based on a bare-metal operating system that we developed to guarantee a deterministic execution environment at all time points. Our testing was accomplished using a set of carefully designed synthetic benchmarks as well as TACLeBench benchmarks.

If a subject learns about the properties of an alternative under a high state of food deprivation, it will prefer this alternative over a similar one in a later choice test, although the subject is currently under a relative state of satiety. In this experiment, we probe this effect in a delay-discounting task, where the reward of the experienced alternative is progressively delayed. Eight male Wistar rats were trained to respond to an alternative under a high state of deprivation and eight rats under a relative state of satiety. After 20 sessions, their weight was recalibrated to a state of relative satiety. Then, they were exposed to a delay-discounting task where the long-larger alternative was the one used during training. The group that experienced the alternative under a higher level of food deprivation preferred more this alternative, and its preference stayed across time. On the contrary, the group that experienced the alternative under a lower level of food deprivation systematically preferred the small-shorter alternative. Our results support that the reinforcement value may be sensitive to the organism's state at the moment an alternative is experienced for the first time.

Delay-tolerant networks (DTN) is an approach to deal with scarce network connectivity found in sparse mobile ad-hoc networks (MANETs) which makes the problem of routing messages a challenging task. DTNs have find their usefulness in many challenging environments such as tactical networks, underwater sensor networks, wildlife monitoring, disaster recovery etc. Pocket Switched Networks (PSNs) have emerged as a new application of the delay tolerant networks where network nodes are computing devices carried by humans. Hence, the study of how humans interact in their day-to-day life, the places they visit frequently, the people they meet frequently, the social groups in which they participate on regular basis etc. can help improve routing process in PSNs. This type of routing inspired from the way humans interact with each other is referred to as social based routing and had been a recent topic of research in the field of DTNs. This paper presents a comprehensive survey of the various social-based algorithms that have been designed for Delay Tolerant Networks.

In strawberry production, the combination of high productive performance and fruits with desirable physicochemical characteristics requires the use of plants of good quality and high initial vigor. This study aimed to evaluate the effect of plants with different crown diameters on the productive performance and fruit quality of strawberry plants of the cultivar 'Pircinque.' The study was conducted in two evaluation cycles (2016/2017 and 2017/2018). The experimental design was in randomized blocks, with four repetitions, and plots consisting of 20 plants. This study evaluated the crown diameters of plants of 5, 7, 9, 11, 13, 15, 17, and 19 mm. The productivity and number of fruit values increased significantly with larger caliber plants, which also provided precocity of productivity. The use of more vigorous plants also favored the production of fruits with higher soluble solids / titratable acidity ratios and with epidermis coloration closer to intense red. For the cultivar 'Pircinque', the plant crown diameters between 15 and 17 mm are the most favorable because they condition the best productive performances in combination with precocity and good fruit quality.

The band gap research in graphene is still a very important topic for materials application. Here, we report a band gap opening and p-type semiconducting property of the graphene by using an electrochemical doping on graphene surface. The manganese-oxide nanopar-ticles adsorbed on the graphene were used as the dopants in an electrolyte, which induce the band gap opening and the change of electronic structure. In addition, the fabricated graphene FET shows the p-type semiconductor behaviors. The temperature dependent conductivity of the p-type doped graphene at applied potential of 1.5 V during electro-chemical doping shows the formation of band gap of 0.23 eV, which is obtained from the fitting of conductivity equation. The semiconducting properties of manganese-oxide doped graphene is attributed to the formation of manganese-oxide nanoparticle on the surface of graphene.

In 1948, Skinner described the behavior of pigeons under response-independent schedules as “superstitious,” and proposed that the responses were reinforced by contiguous, adventitious food deliveries. Subsequently, response-independent schedules have been of interest to both basic and applied researchers, first to understand the mechanisms involved, and later, as “noncontingent reinforcement” (NCR) to reduce undesirable behavior. However, the potential superstitious effects produced by these schedules have been challenged, with some researchers arguing that antecedent variables play a significant role. This paper examines the evidence for adventitious reinforcement from both laboratory and applied research, the results of which suggest that antecedent, non-operant functions may be important in fully understanding the effects of NCR. We propose an applied-basic research synthesis, in which attention to potential non-operant functions could provide a more complete understanding of response-independent schedules. We conclude with a summary of the applied implications of the non-operant functions of NCR schedules.

G protein-coupled receptors (GPCRs) are amongst the most pharmaceutically relevant and well-studied protein targets, yet unanswered questions in the field leave significant gaps in our understanding of their nuanced structure and function. 3D pharmacophore models are powerful computational tools in silico drug discovery, presenting myriad opportunities for the integration of GPCR structural biology and cheminformatics. This review highlights success stories in the application of 3D pharmacophore modeling to de novo drug design, discovery of biased and allosteric ligands, scaffold hopping, QSAR analysis, hit-to-lead optimization, GPCR de-orphanization, mechanistic understanding of GPCR pharmacology and elucidation of ligand-receptor interactions. Furthermore, advances in the incorporation of dynamics and machine learning will be highlighted. The review will analyze challenges in the field of GPCR drug discovery, detailing how 3D pharmacophore modeling can be used to address them. Finally, we will present opportunities afforded by 3D pharmacophore modeling in the advancement of our understanding and targeting of GPCRs.

We prove that it is necessary to introduce the non-zero gluon masses into the fundamental Lagrangian of Quantum Chromodynamics in order to describe the mass-gap in the reaction of electron-positron annihilation into hadrons. A new restriction on the gluon masses is obtained. The renormalized theory with non-zero Lagrangian gluon masses is constructed.

The rank-3 antisymmetric tensors which are the magnetic monopoles of SU(N) Yang-Mills gauge theory dynamics, unlike their counterparts in Maxwell’s U(1) electrodynamics, are non-vanishing, and do permit a net flux of Yang-Mills analogs to the magnetic field through closed spatial surfaces. When electric source currents of the same Yang-Mills dynamics are inverted and their fermions inserted into these Yang-Mills monopoles to create a system, this system in its unperturbed state contains exactly 3 fermions due to the monopole rank-3 and its 3 additive field strength gradient terms in covariant form. So to ensure that every fermion in this system occupies an exclusive quantum state, the Exclusion Principle is used to place each of the 3 fermions into the fundamental representation of the simple gauge group with an SU(3) symmetry. After the symmetry of the monopole is broken to make this system indivisible, the gauge bosons inside the monopole become massless, the SU(3) color symmetry of the fermions becomes exact, and a propagator is established for each fermion. The monopoles then have the same antisymmetric color singlet wavefunction as a baryon, and the field quanta of the magnetic fields fluxing through the monopole surface have the same symmetric color singlet wavefunction as a meson. Consequently, we are able to identify these fermions with colored quarks, the gauge bosons with gluons, the magnetic monopoles with baryons, and the fluxing entities with mesons, while establishing that the quarks and gluons remain confined and identifying the symmetry breaking with hadronization. Analytic tools developed along the way are then used to fill the Yang-Mills mass gap.

Spatial and temporal variation of the free electron concentration in the ionosphere affects SAR interferograms, in particular at low radar frequencies. In this work the identification, estimation and compensation of ionospheric path delay phases in PALSAR-3 and NISAR-L interferograms is discussed. Both these L-band sensors acquire simultaneously SAR data in a main spectral band and in an additional, spectrally separated, narrower second band to support the mitigation of ionospheric path delays. The methods presented permit separating the dispersive and the non-dispersive phase terms based on the double-difference interferogram between the two available spectral bands and the differential interferogram of the main band. The applicability of the proposed methods is demonstrated using PALSAR-3-like data that was simulated based on PALSAR-2 SM1 mode data.

Background: Skin substitutes play a crucial role in wound care by actively modulating the wound healing process, promoting angiogenesis, and protecting the integrity of the native extracellular matrix. Consequently, surgeons have increasingly recognized these resources as excellent complements to improve reconstructive outcomes. This review focuses on the author's experience using these biomaterials in complex cases, highlighting the benefits they bring to patient care. Methods: A literature review was conducted to evaluate the regenerative properties of skin substitutes and their applicability in head and neck, upper and lower extremities, and trunk reconstruction. Results: The reviewed literature, along with the authors' experience, supports the adjunct use of skin substitutes in various reconstructive situations. Combining them with skin grafts improves resulting skin quality and may also enhance donor site healing. They have proven effective in addressing chronic venous ulcers, traumatic wounds with limited donor tissues for coverage, extensive burns, diabetic foot ulcers, and oncologic resections in the face and scalp. Furthermore, combining them with autologous tissue shows promising results in achieving stable closure. Conclusions: Incorporating skin substitutes in complex reconstructive scenarios offers multiple benefits. Their regenerative properties and ability to modulate the healing process contribute to enhanced outcomes and reduced overall costs.

In this paper, we obtain the existence and uniqueness theorem for solutions of Caputo type fractional stochastic delay differential systems (FSDDSs) with Poisson jumps by utilizing delayed perturbation of Mittag-Leffler function. Moreover, by using Burkholder-Davis-Gundy's inequality, Doob's martingale inequality and Holder inequality, we prove that the solution of the averaged FSDDSs converges to that of the standard FSDDSs in the sense of Lp. Some known results in the literature are extended.