This paper focuses on optimal sensor positioning for monitoring activities of daily living and investigates different combinations of features and models on different sensor positions, i.e., the side of the waist, front of the waist, chest, thigh, head, upper arm, wrist, and ankle. Sixteen features are extracted and the feature importance is measured by using the Relief-F feature selection algorithm. Eight classification algorithms are evaluated on a dataset collected from young subjects and that collected from elderly subjects, with two different experimental settings. To deal with different sampling rates, signals with a high data rate are down-sampled and a transformation matrix is used for aligning signals to the same coordinate system. The thigh, chest, side of the waist, and front of the waist are the best four sensor positions for the first dataset (young subjects), with average accuracy values being greater than 95%. The best model obtained from the first dataset for the side of the waist is validated on the second dataset (elderly subjects). The most appropriate number of features for each sensor position is reported. The results provide a reference for building activity recognition models for different sensor positions, as well as for data acquired from different hardware platforms and subject groups.

In this work, an analog front-end (AFE) circuit for Electrocardiogram (ECG) detection system has been designed, implemented, and investigated in an industry-standard Cadence simulation framework using advanced technology node of 45 nm. The AFE consists of an instrumentation amplifier, a Butterworth band-pass filter (with fifth-order low-pass and second-order high-pass sections), and a second-order notch filter- all are based on two-stage, Miller-compensated operational transconductance amplifiers (OTA). The OTAs have been designed employing the $g_m/I_D$ methodology. Both the pre-layout and post-layout simulation were carried out. The layout consumes an area of 0.0058 mm$^2$ without the resistors and capacitors. Analysis of various simulation results were carried out for the proposed AFE. The circuit demonstrates a post-layout bandwidth of 239 Hz with a variable gain between 44 to 58 dB, a notch depth of -56.4 dB at 50.1 Hz, a total harmonic distortion (THD) of -59.65 dB (less than 1\%), an input referred noise spectral density of $

Promoting the sustainable development of resource-based cities is of great significance to the ecological protection and high-quality development of the Yellow River Basin. Combining the environmental status and economic development, we objectively evaluate the ecological safety level of resource-based cities in the Yellow River Basin, compare and analysis the main factors affecting the ecological safety of different resource-based cities, and formulate precise and differentiated ecological safety protection measures in river basins to achieve high-quality development. Taking the Yellow River Basin as an example, this paper analyses the ecological level of the Yellow River Basin based on the theory of sustainable development, calculates the ecological safety level of 30 resource-based cities in the Yellow River Basin from 2006 to 2020 by TOPSIS model, and makes convergence analysis by classification. Through the DID empirical test of sustainable development planning policy on ecological safety factors, distinguish the development characteristics of different resource-based cities. The results show that: (1) the ecological safety level of resource-based cities in the Yellow River Basin is generally developing well, and there are differences among different types of resource-based cities; (2) the kinetic energy of sustainable development of resource-based cities in the Yellow River Basin is mainly industrial transformation, and the power of science and technology is insufficient; (3) local governments pay limited attention to environmental protection, and the sustainable development planning of resource-based cities in 2013 mainly promotes the adjustment of industrial structure of resource-based cities.

The most important plastic resins used for wire coating are Polyvinyl Chloride (PVC), Nylon, Polysulfone and Low-high density polyethylene (LDPE / HDPE). In this article,the coating process is performed using elastic-viscous fluid as a coating material for wire coating in a pressure type coating die. The elastic-viscous fluid is electrically conducted in the presence of an applied magnetic field. The governing non-linear equations are modeled and then solved analytically by utilizing an Adomian decomposition method (ADM). The convergence of the series solution is established. The results are also verified by Optimal Homotopy Asymptotic Method (OHAM). The effect of different emerging parameters such as non-Newtonian parameters α and β, magnetic parameter M and the Brinkman number Br on solutions (velocity and temperature profiles) are discussed through several graphs. Additionally, the current result also compares with the published work already available in the literature.

The next-generation communication systems demand integration of sensing, communication, and power transfer (PT) capabilities, requiring high spectral efficiency, energy efficiency, and low cost, while also necessitating robustness in high-speed scenarios. Integrated sensing and communication systems (ISACS) exhibit the ability to simultaneously perform communication and sensing tasks using a single RF signal, while simultaneous wireless information and power transfer (SWIPT) systems can handle simultaneous information and energy transmission, and orthogonal time frequency space (OTFS) signals are adept at handling high Doppler scenarios. Combining the advantages of these three technologies, a novel cyclic prefix (CP) OTFS based integrated simultaneous wireless sensing, communication, and power transfer system (ISWSCPTS) framework is proposed in this work. Within the ISWSCPTS, the CP-OTFS matched filter (MF) based target detection and parameters estimation (MF-TDaPE) algorithm is proposed to endow the system with sensing capabilities. To enhance the system’s sensing capability, a waveform design algorithm based on CP-OTFS ambiguity function shaping (AFS) is proposed, which is solved by iteratively method. Furthermore, to maximize the system’s sensing performance under communication and PT Quality of Service (QoS) constraints, a semidefinite relaxation (SDR) beamforming design (SDR-BD) algorithm is proposed, solved using through SDR technique. Simulation results demonstrate that the ISWSCPTS exhibits stronger parameter estimation performance in high-speed scenarios compared to orthogonal frequency division multiplexing (OFDM), waveform designed by CP-OTFS AFS demonstrates superior interference resilience, and beamforming designed by SDR-BD strikes a balance in the overall performance of the ISWSCPTS.

Microplastics, which are plastic particles smaller than 5 mm in size, are a growing environmental concern since they have been found in oceans, rivers, lakes, and even on land. These tiny particles can escape water filtration systems and end up in water bodies as well as through the degradation of the larger plastic products causing serious environmental and food safety concerns. This research represents the magnitude of this pollution, characterization of microplastic contamination, its type of polymer, and possible sources of this pollution in the rivers around Dhaka, Bangladesh. Quantitative analyses were done following the method suggested by the NOAA and other conventional methods. Among the rivers, Buriganga has the highest microplastic pollution with 3.654 items/L in surface water and 43.125 items/kg in sediment. The concentration in Shitalakshya and Turag rivers are 3.011 items/L and 2.051 items/L in surface water and 34.875 and 17.875 items/kg in sediment respectively. ANOVA test revealed a significant difference between the concentration level of microplastic in the surface water of the Burigana and Turag rivers. A positive correlation between the concentration level of microplastic in the surface water and the sediment was also found. On average 58% of the microplastics were found to be fibrous in surface water. Qualitative analyses were done to find the characteristics and chemical composition of the microplastics. Through the use of FTIR spectroscopy, the study identified different kinds of synthetic polymers in the sample including polyamide (Nylon), polyethylene (PE), polystyrene (PS), polypropylene (PP), polyethersulfone (PES), polyvinyl chloride (PVC), and polyethylene terephthalate (PET) and polyethylene were the most abundant polymer in the samples. This study involved the investigation of three distinct rivers located in the vicinity of Dhaka city

“Dark Web” usually describes a new world of e-living space perceived as a place, free from con-straints, in which its main actors generally are criminal, unstable, and mentally disturbed individ-uals. Nowadays, advancements in information and internet technologies have made the Dark Web more accessible in recent decades. The Dark Web is a virtual world component; therefore, as-sessing users’ behavior may be crucial in understanding motivation to use it. This study aims to discuss the behavior patterns of Dark Web users within the theoretical framework of the technol-ogy acceptance model via a structural equation model. The resulting structural equation model showed that considered causal relationships were statistically significant.

Cloud computing refers to applications delivered as services over the Internet. Cloud systems employ policies that are inherently dynamic in nature and that depend on temporal conditions defined in terms of external events, such as the measurement of bandwidth, use of hosts, intrusion detection or specific time events. In this paper, we investigate an optimized resource management scheme named v-Mapper. The basic premise of v-Mapper is to exploit application-awareness concepts using software-defined networking (SDN) features. This paper makes three key contributions to the field: (1) We propose a virtual machine (VM) placement scheme that can effectively mitigate the VM placement issues for data-intensive applications; (2) We propose a validation scheme that will ensure that a service is entertained only if there are sufficient resources available for its execution and (3) We present a scheduling policy that aims to eliminate network load constraints. An evaluation was carried out with various benchmarks and demonstrated that v-Mapper shows improved performance over other state-of-the-art approaches in terms of average task completion time, service delay time and bandwidth utilization. Given the growing importance of supporting large-scale data processing and analysis in datacentres, the v-Mapper system has the potential to make a positive impact in improving datacentre performance in the future.

This paper presents an innovative multi-agent, data-driven reinforcement learning (RL) approach to develop and utilize the thermal equivalent network model that represents the motor's thermal dynamics. A multi-agent reinforcement learning is designed and trained to adjust the model parameters using data from several motor driving cycles. To ensure the incoming driving cycle matches the historical data before employing the pre-trained RL agents, offline statistical analysis and clustering techniques are developed and used. Numerical simulations highlighted the RL agent's ability to develop strategies that effectively address the variability of driving cycles. The proposed RL framework showed its capability to accurately reflect the motor's thermal behavior under various driving conditions.

This article presents a detailed examination of the methodology and modeling tools utilized to analyze gas flow in pipelines, rooted in the fundamental principles of gas dynamics. The methodology integrates numerical simulations with modern neural network techniques, particularly focusing on the Physics-Informed Neural Network (PINN) method. This innovative approach combines artificial neural networks (ANNs) with physical equations, offering a more efficient and accurate way to model various complex processes and phenomena. The proposed mathematical model, based on the Euler equation, has been meticulously implemented using the Python language. Verification with analytical solutions ensures the accuracy and reliability of the computations. In the research, a comprehensive comparative analysis was conducted between results obtained using the PINN method and those from conventional Computational Fluid Dynamics (CFD) approaches. The analysis highlighted the advantages of the PINN method, which produced smoother pressure and velocity fluctuation profiles while reducing computation time, demonstrating its potential as a transformative modeling tool. The data derived from this study are of paramount importance for ensuring ongoing energy supply reliability and can also be used to create predictive models related to gas behavior in pipelines. The application of modeling techniques for gas flow simulation has the potential to revolutionize the integrity of our energy infrastructure and utilization of gas resources. However, it is crucial to emphasize that the effectiveness of such models relies on continuous monitoring and frequent updates to ensure alignment with real-world conditions. This research not only contributes to a deeper understanding of compressible gas flows but also underscores the crucial role of advanced modeling methodologies in the sustainable management of gas resources for both current and future generations.

The objective of this work is to analyze the improvement of heat transfer in trapezoidal fin heat exchangers using numerical simulation. Heat exchangers are essential components frequently used in contemporary electronic gadgets to effectively disperse heat produced by high-power components. Nevertheless, as electronic devices continue to advance and become more powerful, the heat transfer capacity of heat exchangers is facing more requirements, therefore requiring enhanced heat dissipation efficiency. Afterwards, various fin angles were adjusted, and the heat transmission efficiency was compared. Modifying the angles can significantly improve the effi-ciency of convective heat dissipation. Moreover, it has been found that employing an optimized trapezoidal fin structure can further enhance the efficiency of heat transfer. The results indicate that trapezoidal fin heat exchangers provide superior heat dissipation efficiency compared to conventional heat exchangers. This is important for enhancing the thermal dissipation capabili-ties of electrical gadgets, hence guaranteeing steady functionality and extending their longevity. Subsequent study might explore supplementary methods to boost heat transmission in different heat exchanger configurations in order to meet the growing requirements for heat dissipation.

This paper presents an alternative conceptualization and definition of technology in the context of university technology transfer. The ambiguity regarding the conceptualization of technology is apparent in the technology transfer literature. An expanded conceptualization of technology potentially opens new approaches to researching the topic of technology transfer. It may also cause policymakers to think more comprehensively about what it means to successfully transfer technologies derived from federally funded research to the private sector for use that benefits the public interest. This paper integrates constructs and ideas in the related literature to provide a new perspective of technology that can support future scholarly research and public policy formulation about technology transfer in general, and university technology transfer specifically. Although the paper focuses on university technology transfer to the private sector in the United States, the insights it presents are relevant to technology transfer more broadly and applicable in other geopolitical contexts.

Promoting green development has become an important way to optimize the ecological and economic structure and promote sustainable development. The Yangtze River Economic Belt is an important economic corridor in China, and it remains to be examined whether the implementation of environmental regulations has enhanced the green total factor productivity (GTFP) of cities. This paper calculates the green total factor productivity of 107 cities within the Yangtze River Economic Belt by using the super-efficient SBM model and the GML index with Chinese city panel data from 2007-2019 and measures the intensity of environmental regulations through textual analysis. The bidirectional fixed-effects model constructed in this paper suggests an inverted U-shaped relationship between environmental regulation and GTFP, which is confirmed by a series of robustness tests. Green technology innovation and advanced industrial structure play a mechanism role in this. In regions with lower levels of green technology and industrial structure, the inverted U-shaped relationship between environmental regulation and green total factor productivity is more significant. In addition, the phenomenon of GTFP rising and then falling because of environmental regulation is more obvious in cities in the middle and upper reaches of the Yangtze River and outside the urban agglomerations. Therefore, when formulating environmental regulation policies, it is necessary to balance the relationship between economic development and environmental protection and harmonize the environment and economic development of the entire Yangtze River Basin.

Vanilla planifolia is grown as a high-value orchid spice for its odor and savor attributes that increase due to the curing process associated with microbial colonization. This tends to influence the aromatic properties of vanilla. Hence, 11 Bacillus sp. strains were isolated from V. planifolia and identified with 16S rRNA gene sequencing. The liquid culture (1 mL of 107 CFU mL-1) of selected Bacillus vallismortis NR_104873.1:11-1518, B. velezensis ZN-S10, and B. tropicus KhEp-2 effectively fermented green-blanched vanilla pods kept at 10 ℃ during the sweating stage. GC-MS analysis showed that the methanol extract of non-coated, and B. vallismortis treated vanilla detected three (3) volatile compounds, whereas seven (7) components were obtained in B. tropicus and B. velezensis treatment. 4H-pyran-4-one, 2,3-dihydro-3,5-dihydroxy-6-methyl was found in B. velezensis ZN-S10, B. tropicus KhEp-2, B. vallismortis while it was not present in the control samples. This ketone compound suggested a Maillard reaction resulting in brown-increased aroma pods. Linoleic acid and Hexadecanoic acid ethyl esters were detected only in ZN-S10 strain-coated vanilla. A novel 3--Deoxy-d-mannoic lactone was detected only in B. vallismortis treated vanilla characterized as a new compound in V. planifolia which suggested that the new compound can be altered with the coating of bacteria in vanilla during fermentation. Thus, the Bacillus strains improved the volatile profile and exhibited a new aroma and flavor profile of vanilla owing to bacteria fermentation during the curing process.

. Protein cysteine S-glycosylation is a relatively rare and less well characterized post-translational modification (PTM). Creating reliable model proteins that carry this modification is challenging. The lack of available model or natural S-glycosylated proteins significantly hampers the development of MS-based methodologies for detecting protein cysteine S-glycosylation in real-world proteomic studies. There is also limited MS-sequencing data describing easier to create synthetic S-glycopeptides. Here, we present the results of an in-depth manual analysis of automatically annotated CID/HCD spectra for model S-glucopeptides. The CID spectra show a long series of y/b-fragment ions with retained S-glucosylation, regardless of the dominant m/z signals corresponding to neutral loss of 1,2-anhydroglucose from the precursor ions. In addition, the spectra show signals manifesting glucosyl transfer from the cysteine position onto Lys, Arg side chains, and a peptide N-terminus. Other spectral evidence indicates that the N-glucosylated initial products of transfer are converted into N-furanosylated (i.e., glycated) structures due to Amadori rearrangement. We discuss the peculiar transfer of the glucose oxocarbenium ion (Glc+) to positively charged guanidinium residue (ArgH+) and propose a mechanism for the gas-phase Amadori rearrangement involving a hydride ion shift.

Perovskite solar cells (PSCs) are vital for their optical and electrical properties, with lead-based PSCs reaching a remarkable efficiency of 26.1%, while tin-based counterparts achieve 18.71%. Due to lead's toxicity, there's a push for alternatives like tin. However, tin-based PSCs suffer from stability issues and high defect density states, necessitating the development of cost-effective, high-performance, and eco-friendly alternatives. In this study, we designed a hetero-junction architecture using MASnI3-based Perovskite, opti-mized with SCAPs-1D. After exhaustive analysis, our device achieved a power conversion efficiency of 24.18%, with enhanced parameters including Voc of 0.09323V, Jsc of 30.8360 mA/cm2, and FF of 84.10%. Recombination rates, particularly Shockley-Read Hall recom-bination, were significantly reduced. Parametric analyses, encompassing absorber layer thickness, band gap, defect density, doping concentration, and operating temperature, in-dicate potential efficiency enhancements. This underscores the viability of Sn-based PSCs as a cost-effective, efficient, and environmentally benevolent alternative to lead-based counterparts, promising advancements in future research and development efforts.

This paper presents the results of a study aimed at understanding how technology maturity level influences the incidence of university technology transfer to the private sector. The study examined the topic from the perspective of private sector organizations. It used data from a random sample of patent applications filed with the United States Patent and Trademark Office and a theoretically guided sampling of multiple cases of private sector organizations that contemplated obtaining and assimilating technologies created at universities in the United States. The patent application data were analyzed using nonparametric statistical techniques and the case data were analyzed using qualitative comparative analysis (QCA). The findings of the study suggest that the typical maturity level of technologies created at U.S. universities is a TRL-5 or lower on as scale adapted from the NASA technology readiness level (TRL) scale. A technology maturity level of TRL-6 or higher is likely an insufficient but necessary part of at least one unnecessary but sufficient configuration of conditions that tends to result in the occurrence of university technology transfer. However, under certain circumstances, a technology maturity level of at least TRL-6 could be a sufficient but unnecessary condition for the occurrence of university technology transfer. These findings have several important implications. First, they provide support for the notion that university technology transfer is subject to causal complexity. Moreover, it may be possible to increase the incidence of university technology transfer in the United States by implementing public policy and practices that explicitly take technology maturity level into consideration.

The theory and working principle of fabric phase sorptive extraction (FPSE) is presented that eloquently explains the mystery behind this new and powerful sample preparation technique. FPSE innovatively integrates the benefits of sol-gel coating technology and the rich surface chemistry of cellulose/polyester/fiberglass fabric, resulting in a microextraction device with very high sorbent loading in the form of an ultra-thin coating. This porous sorbent coating and the permeable substrate synergistically facilitate very fast extraction equilibrium. The flexibility of the FPSE device allows for direct insertion into original, unmodified samples of different origin. Strong chemical bonding between the sol-gel sorbent and the fabric substrate permits the exposure of FPSE devices to any organic solvent for analyte back-extraction/elution and to highly acidic or basic environments (pH 1-12) if required. A sol-gel derived sorbent, highly polar sol-gel poly(ethylene glycol) coating, was generated on cellulose substrates. Five cm2 segments of these coated fabrics were used as the FPSE devices for sample preparation using direct immersion. An important class of environmental pollutants, substituted phenols, was used as model compounds to evaluate the extraction performance of FPSE. The high primary contact surface area (PCSA) of the FPSE device and porous structure of the sol-gel coatings resulted in very high sample capacities and incredible extraction sensitivities for both the compound classes in a relatively short period of time. Different extraction parameters were evaluated and optimized. The new extraction devices demonstrated part per trillion level detection limits for substitute phenols, a wide range of detection linearity, and good performance reproducibility.

Abstract: A. baumannii exhibits resilience in harsh environments and progressively develops resistance to diverse antibacterial agents over time. This adaptability poses a significant challenge in treating an infection caused by this bacterium within healthcare settings. The presence of peptidoglycan, a crucial precursor for cell wall synthesis, contributes to this challenge. Peptidoglycan serves not only as a structural support in bacterial cells but also provides protection against adverse environmental conditions. The synthesis of the peptidoglycan layer involves a group of substrates such as N-acetylglucosamine (GlcNAc) and N-acetylmuramic acid (MurNAc), within a three-partitioned process occurring in the membrane, periplasmic space, and cytoplasm of each bacterium. Initiated in the cytoplasm and extending to the inner cell membrane, this synthesis starts with the production of nucleotide precursors. The first step involves the synthesis of UDP-GlcNAc, orchestrated by Glm (GlmS, GlmM, and GlmU) enzymes using fructose-6-phosphate. Subsequently, enzymes from the Mur family, namely MurB, MurA, MurD, MurC, MurI, MurF, and MurE, synthesize UDP-N-acetylmuramyl-pentapeptide (UDP-Mpp) from UDP-GlcNAc. Concurrently, on the cytosolic side, the production of membrane-surrounded undecaprenyl phosphate occurs, involving membrane-side proteins MraY and MurG in the biosynthesis of peptidoglycan. This review emphasizes updated information on Mur family proteins, encompassing physicochemical properties, nature of binding site, number and type of binding site residues, functional domain details, three-dimensional structural aspects, and their functions within bacterial cells. Special attention is directed towards their enzymatic role in peptidoglycan biosynthesis due to the limited availability of precursors in the market. Additionally, the review provides a comprehensive summary of existing inhibitors and ongoing efforts in identifying new targeted inhibitors, recognizing these enzymes as potential candidates for antibacterial drug design and discovery.

The underlying assumption of the discourse about technology transfer is that government intervention is legitimate. Little scholarship has examined whether this assumption is valid or not and on what basis. Legitimacy is an important construct in the context of public policy. Government intervention can only be sustained if the public views such action as legitimate. The creation and transfer of technologies to the private sector is an area where there is significant government intervention. This paper reconceptualizes political legitimacy in the context of technology transfer policy. The analysis illuminates several concerns and challenges regarding the traditional approach to understanding whether specific government interventions in technology transfer are legitimate. It subsequently applies social constructionism and the notion of morality tales to describe an alternative conceptualization of political legitimacy that integrates aspects of other frameworks. In doing so, it reimagines political legitimacy as less of an unattainable normative principle of limited practical value to policymakers and more of a descriptively understood social phenomenon that policymakers can apply while formulating not only technology transfer policy, but other kinds of public policy as well. The paper demonstrates that there is a broader basis for claims of political legitimacy for government intervention in technology transfer, there is likely a more expansive range of technology transfer problems with which the government can rightly concern itself as well as possible solutions that policymakers can justifiably consider for addressing those problems, and that the political consequences of potential overreach in technology transfer policy are likely minimal.

Seed potato treatment is vital for plant protection, yield enhancement, and product quality. In the conducted research, the plant biostimulator Supporter was applied to evaluate its impact on potato yields. Field studies were conducted in Northeastern, Northwestern, Western, and Southwest Poland from 2015 to 2017, using a randomized complete block design with a split-plot arrangement. The use of seed treatment technology with the Supporter product resulted in increased overall and commercial potato yields and improved yield tuber structure compared to traditional cultivation methods without tuber treatment before planting. Conclusion: The application of the plant biostimulator Supporter in seed potato treatment technology brings significant benefits, including, increased potato yield and improved yield structure. The cultivation location significantly influences potato yield and tuber structure. Understanding these differences can aid in better adapting cultivation practices and selecting varieties to specific local conditions, potentially leading to increased potato crop productivity. In terms of efficiency and yield quality, further research into its application in agricultural practice is recommended, which may contribute to further increasing potato production efficiency and quality. Developing more ecological and efficient farming practices can help meet society's growing food needs.

In the intersection of the Internet of Things (IoT) and Machine Learning (ML), the choice between high-level and low-level programming libraries presents a significant dilemma for developers, impacting not only the efficiency and effectiveness of ML models but also their environmental footprint. We have proposed a comprehensive framework to aid in this decision-making process, underpinned by a detailed comparative analysis of both types of libraries on one of the key IoT ML task; image classification. We have introduced a novel algorithm designed to calculate the green footprint of ML model training, factoring in execution time, memory utilization, power consumption, and CPU temperature, addressing the urgent need for sustainable ML practices. Through an empirical evaluation of popular libraries such as PyTorch for high-level and Libtorch for low-level development, we have assessed their performance, development efficiency, and hardware compatibility. The culmination of our research is a decision support system that synthesizes the experimental findings to guide developers toward choices that harmonize model performance with environmental sustainability.

Moso bamboo is famous for fast growing and biomass accumulation, as well as high annual output for timber and bamboo shoots. These high outputs require high nutrient inputs to maintain and improve stand productivity. Soil nitrogen (N), phosphorus (P) and potassium (K) are important micronutrients for plant growth and productivity. Due to high variability of soils, analysing spatial patterns of soil N, P and K stocks is necessary for scientific nutrient management in Moso bamboo forests. In this study, soils were sampled from 138 locations across Yong’an City and ordinary kriging was applied for spatial interpolation of soil N, P and K stocks. Soil N stock showed a strong spatial dependence while soil N and P stocks presented a moderate spatial dependence, indicating soil N was mainly controlled by intrinsic factors while soil N and P stocks were controlled by both intrinsic and extrinsic factors. Different spatial patterns were observed for soil N, P and K stocks across the whole study area, indicating that fertilizations with different ratios of N:P:K should be applied for different sites to maintain and improve stand productivity. The total soil N, P and K stocks within 0-60 cm were 0.624, 0.020 and 0.583 Tg, respectively.

Nanling Mountain region is a typical southern hilly region, which plays an important ecological and environmental protection role in China's overall land protection pattern. Based on the remote sensing image data of Longnan City in Nanling Mountain in 2013, 2018 and 2023, this paper interpreted the land use type and analyzed the land use transfer situation by using Land use transfer flow, and Land use transfer matrix. At the same time, based on the remote sensing Ecological index (RSEI) model, the ecological environment quality of Longnan City from 2013 to 2023 was retrieved. The temporal and spatial response model of ecological environment quality to land use transfer in Longnan City from 2013 to 2023 was discussed based on Spatial autocorrelation and Geographic detector. The results show that from 2013 to 2023, the decrease of forest land (16.23km²) and the increase of construction land (13.25km²) were the main land use transfer in Longnan City. The ecological environment index of Longnan City in 2013, 2018 and 2023 was 0.789, 0.917 and 0.872, respectively, showing a trend of "first rising and then decreasing". The ecological environment quality in the north of Longnan City was significantly lower than that in the south, and the poor ecological quality area appeared in and around the northern main urban area, showing a trend of "inward contraction". Forest land, garden land, grassland, cultivated land and water area have a positive impact on ecological environment quality, while traffic land, construction land and other land have a negative impact on ecological environment quality. The response of ecological environment quality to different land use transfer modes is related to the change of the overall ecological environment quality. The interaction between LUCC and other factors had a great impact on the evolution of ecological environment quality in Longnan City.

Pipeline conflicts arising from data dependencies are a common issue encountered in the hardware implementation of layered QC-LDPC decoders. This paper proposes an efficient layered decoding architecture to reduce pipeline conflicts without introducing stall cycles, by reordering the processing order offline and using the patch method based on variable-to-check message. The experimental results on the LDPC code of the IEEE802.16 standard in the OFDM-PON system demonstrate that the proposed architecture has a sensitivity improvement of 0.125 dBm and 0.375 dBm, respectively, compared with our previous work and the method described in the other work.

The electronic properties of calcium intercalated graphite (CaC6) as a function of pressure are revisited using density functional theory (DFT). The electronic band structures of CaC6, like many other layered superconducting materials, display cosine-shaped bands at or near the Fermi level (FL). Such bands encompass bonding/antibonding information with a strong connection to superconducting properties. Using an hexagonal cell representation for CaC6, construction of a double supercell in the c-direction effects six-folding in reciprocal space of the full cosine function, explicitly revealing the bonding/antibonding relationship divide at the cosine midpoint. Similarly, folding of the Fermi surface (FS) reveals physical phenomena relevant to electronic topological transitions (ETT) with application of pressure. For CaC6, the peak value for the superconducting transition temperature, Tc, occurs at about 7.5 GPa, near to the observed pressure of the calculated ETT. At this pressure, the radius of the nearly spherical Ca 4s-orbital FS coincides with three times the distance from the G centre point to the Brillouin zone (BZ) boundary of the 2c supercell (which is equal to half the identically defined distance for the primitive rhombohedral BZ). In addition, the ETT coincides with alignment of the non-bonding (inflection) point of the cosine band (the point at which the sign of the cosine amplitude modulation is reversed) with the FL. At other calculated pressure conditions, the Ca 4s-orbital FS undergoes topological changes that correspond and can be correlated to experimentally determined changes in Tc. The ETT is a key mechanism that circumscribes the known significant drop in Tc for CaC6 as a function of increasing pressure.

As the world population grows, fulfilling the need for biomaterials in the healthcare system becomes increasingly important. Biomaterials, which include metals, polymers, ceramics, and composites, play an important role in the creation of medical devices that improve people's lives. The European Society for Biomaterials described biomaterials as non-biological materials used in medical devices to interact with biological systems. This definition has developed to encompass materials that treat, assess, or replace tissues or bodily functions. Biocompatibility, as defined by the FDA, is a key feature of biomaterials, as is the requirement to fulfil design requirements such as mechanical performance, geometry, and electrical control. Over the last decade, advances in regenerative medicine and tissue engineering have boosted biomaterials' usage in medical applications dramatically. Despite its promise, scientists, engineers, and physicians continue to face significant challenges due to the complexity of biomaterials. Biomaterials have various benefits, including biodegradability, non-toxicity, and biocompatibility, making them extremely useful for replacing, sustaining, or improving biological activities in damaged tissues. They are used in a wide range of applications, including tissue engineering implants, human tissue healing and regeneration, medication delivery systems, and biosensors. This study gives insights into the fundamental characteristics, case studies, and ethical issues associated with the usage and use of biomaterials, further examining their potential and significance in healthcare and medicine.

Brucellosis is a zoonoses caused by bacteria of the genus Brucella, which causes economic losses in livestock and threatens public health. A cross-sectional study was conducted to determine the prevalence of Brucella species and risk factors in smallholder dairy cattle in six regions of Tanzania from July 2019 to October 2020. Dairy cattle (n=2048) were sampled from 1371 farms. DNA ex-tracted from blood and vaginal swabs was tested for Brucella using qPCR targeting the IS711 gene and positives were tested for the alkB marker for B. abortus and BMEI1172 marker for B. melitensis. The molecular prevalence was 3.5% (95% CI: 2.8-4.4) with the highest prevalence 8.1% (95%CI: 4.6-13.0) in Njombe region. B. melitensis was the predominant species detected (66.2%). Logistic regression revealed PCR positivity in dairy cattle was higher in the animals with a history of abortion (OR: 3.17, 95%CI: 1.05-9.62) and farms without dogs around (OR: 2.68, 95%CI: 1.12-5.90). Further studies are recommended to understand the source of B. melitensis and the implications to veterinary public health. Livestock keepers should be informed of the risks and biosecurity practices to reduce introduction and control Brucella. Cattle and small ruminant vaccination pro-grams could be implemented to control brucellosis in high-risk populations in the country.

Background: Asthma is a widespread chronic respiratory disease that poses a significant public health challenge. The current study investigated the associations between air pollution and asthma severity among individuals residing near the Sohar industrial port (SIP) in Oman. Despite the presence of multiple major industrial complexes in Oman, limited knowledge regarding their impact on respiratory health is accredited. Hence, the primary objective of this study is to offer valuable insights into the respiratory health consequences of industrial air pollution in Al Batinah North. Methods: The state health clinics' records for patient visits related to asthma were collected for the timeframe spanning 2014 to 2022. Exposure was defined as the distance from SIP, Majan Industerial Area (MIA) and Sohar Industerial Zone (SIZ) to determine high, intermediate, and low exposure zones (12 km, respectively). Exposure effect modifications by age, gender, and smoking status were also examined. Results: The conducted cross-sectional study of 410 patients (46.1% males and 53.9% females) living in over 17 areas around SIP revealed that 73.2% of asthmatics were under 50 years old, with severity significantly associated with closeness to the port. Risk ratios were estimated to be (RR:2.42; CI95%: 1.01–5.78), (RR:1.91; CI95%: 1.01–3.6), and (RR:1.68; CI95%: 0.92–3.09) for SIP, MIP and SIZ areas, respectively, compared to the control area. Falaj Al Qabail (6.4 km) and Majees (6 km) had the highest number of asthma patients (N. 69 and N. 72), and highest percentages of severe asthma cases among these patients (28% and 24%) with significant risk ratios (RR:2.97; CI95%: 1.19–7.45 and RR:2.55; CI95%: 1.00–6.48), correspondingly. Moreover, severe asthma prevalence peaked in the 25-50 age group (RR:2.05; CI95%: 1.26–3.33), and this linkage between asthma and age was much more pronounced in males than females. Smoking and exposure to certain contaminant (dust and smoke) increased also the risk of severe asthma symptoms, but their effects were less important in the high risk zone, suggesting much more important risk factor. A neural network model accurately predicted asthma risk (94.8% accuracy), with proximity to Sohar Industrial Port as the most influential predictor. Conclusion: The study highlights the High asthma burden near Sohar Industrial Port, linked to port proximity and smoking and wind direction as major risk factors. These findings inform vital public health policies to reduce air pollution and improve respiratory health in the region, prompting national policy review.

Pakistan flora is enriched with potent bioactive compounds that must be explored while Alzheimer's disease (AD) poses a global challenge driven by neurochemical imbalances. Acetylcholinesterase (AChE) inhibitors traditionally alleviate symptoms, but addressing the root cause remains elusive. This gap has led to the exploration of herbal sources for interventions. In this context, we analyzed fifty 50 medicinal plants for their phytochemical composition and antioxidant and acetylcholinesterase inhibition activities. AChE activity was measured using Ellman’s method. Santalum album exhibited significant AChE inhibition (86.2%), surpassing galantamine hydrobromide (81.8%). Promising inhibition was also seen in Bombax ceiba (77.8%), Acacia karoo (52.9%), and Phaseolus lunatus (50.1%). Detailed analysis revealed Santalum album's abundance in terpenoids, flavonoids, tannins, and phenolics, potentially correlating with its antioxidant and AChE inhibitory effects. Acacia karoo demonstrated elevated levels of total alkaloids, antioxidants, terpenoids, and tannins. Both Acacia karoo and Santalum album show promise for AD intervention due to their AChE inhibitory activities and unique phytochemical attributes, warranting further exploration, particularly for Acacia karoo's novel potential in AChE inhibition, to advance targeted AD therapeutics utilizing natural resources. This study contributes to the search for effective AD strategies from nature's pharmacological resources.

This article delves into the enduring relevance of Liberal International Relations (IR) Theory amidst persistent criticisms regarding power dynamics and its applicability in emerging states. Despite its detractors, Liberal IR Theory offers a nuanced understanding of state behavior, blending social contexts with power dynamics. It recognizes the intricacies of economic interdependence and advocates for a balanced approach in advancing democracy and human rights. While nationalism poses challenges to international institutions, their adaptability endures. Leaders, albeit constrained, retain the capacity to foster peace through visionary leadership and global cooperation. By acknowledging its limitations and fostering open dialogue, Liberal IR Theory continues to evolve, poised to contribute to a just and peaceful global order.

Heavy metal accumulation in soils used for agricultural purposes is a major issue as it can affect the growth of plants and contain health risks as plants containing heavy metals are taken as food. This study provided the potential of three Bacillus pumilus strains (C-2PMW-8, C-1 SSK-8, and C-1PWK-7) for mitigation of the health factors related to heavy metals on lettuce (Lactuca sativa) grown in chromium contaminated soil from activities related to mining. Lettuce seeds inoculated with B. pumilus strains were grown in pots with garden soil amended with varying amount of chromite mine soil (2.27%, 4.65%, 7.14%). Growth indicators like days to germination, percentage of germination, leaf weight, leaf area and rate of survival decreased with incremental soil chromium levels but improved highly with inoculation of B. pumilus compared to uninoculated controls. When B. pumilus strains were provided, there was also a decreased level in the buildup of chromium in soil as well as lettuce shoots. The results explains that plant growth-promoting B. pumilus strains may be able to lower down the detrimental effects of chromium on lettuce development, hence increment in the effectiveness of phytoremediation.

The radiative heat transfer in arc plasma models is considered from the point of view of its description in terms of a net emission coefficient, the method of spherical harmonics in its lowest order, and the discrete ordinate method. Net emission coefficients are computed applying approximate and numerical approaches, the multi-band representation of the spectral absorption coefficient with three kinds of its averaging and two datasets. The self-consistent access to the radiative heat transfer is applied to a two-dimensional axisymmetric model of free-burning arc in argon at atmospheric pressure. The results obtained from the models employing the net emission coefficient, the method of spherical harmonics, and the discrete ordinate method are compared.

Keywords: mHealth; peritoneal dialysis; functionality; usability

This paper introduces a new adaptation of the enthalpic lattice Boltzmann method (LBM) tailored to simulate the intricate dynamics of conjugate heat transfer in non-homogeneous media, showcasing considerable potential for enhancing heat exchanger designs. This approach expands upon the conventional enthalpic LBM framework by seamlessly incorporating tailored source terms, enabling precise representation of local and transient variations in the medium’s thermophysical properties. The resulting LBM model comprehensively captures the energy conservation equation, with exceptions made only for flow compressibility and viscous dissipation, thereby significantly augmenting its versatility in analyzing heat exchanger configurations. Verification tests, comprising assessments of both transient and steady-state solutions, unequivocally validate the accuracy of the proposed model, further bolstering its reliability for analyzing heat exchange processes within intricate heat exchanger geometries. To demonstrate its efficacy, simulations of conjugate heat transfer processes involving fluid natural convection within structured cavities were performed, imposing both Dirichlet and Neumann boundary conditions to emulate scenarios encountered in practical heat exchanger operations. The findings yield compelling insights, particularly in the transient regime, revealing the beneficial impact of structured cavities on enhancing heat transfer processes. These insights inform potential design optimizations for heat exchangers. The results emphasize the potential of the modified enthalpic LBM approach to elucidate complex heat transfer phenomena in non-homogeneous media and structured geometries, offering valuable implications for heat exchanger engineering and optimization.

Abstract: Although the pathophysiology of fibromyalgia syndrome has been better understood in recent decades, a unified model of its pathogenesis and an effective therapeutic approach are still far from being realized. The main aim of this article will be to delve into the fundamental mechanisms of the pathophysiology of fibromyalgia conceptualized as stress intolerance syndrome. Using the biopsychosocial model of chronic pain syndromes, we will describe the potential role of the attachment system, C tactile fibers, and oxytocinergic system dysfunction in the pathophysiology of fibromyalgia syndrome and other central sensitivity syndromes. At the end of the article, the therapeutic implications of this new global and translational pathophysiological model will be briefly discussed.

In this study, we present comprehensive climatologies of effective ultraviolet (UV) quantities and photosynthetically active radiation (PAR) over Cyprus for the period 2004 to 2023, leveraging the synergy of earth observation (EO) data and radiative transfer model simulations. The EO dataset, encompassing satellite and re-analysis data for aerosols, total ozone column, and water vapor, alongside cloud modification factors, to capture the nuanced dynamics of Cyprus's atmospheric conditions. With a temporal resolution of 15 minutes and a spatial of 0.05°x0.05°, these climatologies undergo rigorous validation against established satellite datasets and are further evaluated through comparisons with ground-based global horizontal irradiance measurements provided by the Meteorological Office of Cyprus. This dual-method validation approach not only underscores the models' accuracy but also highlights their proficiency in capturing intra-daily cloud coverage variations. Our analysis extends to investigating the long-term trends of these solar radiation quantities, examining their interplay with changes in cloud attenuation, aerosol optical depth (AOD), and total ozone column (TOC). Significant decreasing trends in the noon ultraviolet index (UVI), of -2 to -4% per decade have been found in Autumn, especially marked on the island’s Northeastern part, mainly originating from the (significant) positive trends in TOC. The significant decreasing trends in TOC, of -2 to -3% per decade that were found in Spring do not result in correspondingly significant positive trends in the noon UVI since variations in cloudiness and aerosols also have a strong impact on the UVI in this season. The seasonal trends in the Daylight Integral (DLI) were generally not significant. These insights provide a valuable foundation for further studies aimed at developing public health strategies and enhancing agricultural productivity, highlighting the critical importance of accurate and high-resolution climatological data.

Due to the extraordinary mechanical properties of ultra-high-performance concrete (UHPC), the shear stirrups in UHPC beams could potentially be removed. The aim of this study is to determine the effect of beam height and steel fiber volume content on the shear behavior of non-stirrup UHPC beams under a larger shear span-depth ratio (up to 2.8). Eight beams were designed and fabricated, including six non-stirrup UHPC beams and two comparing stirrup-reinforced normal concrete (NC) beams. The experimental results demonstrated that the volume content of steel fiber could be a crucial factor affecting the ductility, cracking strength, and shear strength of non-stirrup UHPC beams and altering their failure modes. Additionally, the height of the beam had a considerable effect on its shear resistance. This study revealed that the French standard formulae were more accurate for the UHPC beams with larger shear span-depth ratios and PCI-2021 formulae greatly overestimate the shear capacity of UHPC beams with larger shear span-depth ratios. Xu’s formulae were more accurate for the steel fiber-reinforced UHPC beams with larger shear span-depth ratios.

The Imbalance Cost Pass-Through (ICPT) is a flexible component of the Incentive Regulation (IBR) that empowers power producers to adjust tariffs in response to variable fuel prices, thereby enhancing the economic resilience of electricity generation. However, the cost of electricity generation is significantly influenced by the volatility of commodity prices, including coal, gas and LNG. In Malaysia, the Energy Commission has conducted biannual reviews of fuel and other generation costs. Any cost savings or increases identified during these reviews will be passed on to customers in the form of rebates or surcharges. Due to that reason, this study proposes ICPT price forecasting for the electricity market in Peninsular Malaysia. The study aims to construct an ICPT-related baseline model for the peninsular generation data by employing three forecasting methods. The forecasting performance is analysed by a Mean Absolute Percentage Error (MAPE). In findings, the ARIMA method is one of the most accurate forecasting methods for fuel prices compared to the Moving Average (MA) and LSSVM methods. The observed price differences between the ARIMA and LSSVM models for ICPT are minimal. The ICPT price for July-December 2022 and January-June 2023 is MYR 0.21/ kWh for ARIMA and MYR 0.18/kWh for LSSVM, which are close to the actual TNB’s ICPT tariff. As for the forecasting, the ICPT price is expected to drop for the next announcement. The findings of this study may contribute to a positive impact on the sustainability of the energy sector in Malaysia.

Pedestrian trajectories are crucial for self-driving cars to plan their paths effectively. The sensors implanted in these self-driving vehicles, despite being state-of-the-art ones, often face inaccuracies in the perception of surrounding environments due to technical challenges for adverse weather conditions, interference from other vehicles sensors and electronic devices, and signal reception failure, leading to incompleteness in trajectory data. But for real-time decision making for autonomous driving, the trajectory imputation is no less crucial. Previous attempts to address this issue such as statistical inference and machine learning approaches have shown promise. Yet, the landscape of deep learning is rapidly evolving with new and more robust models emerging. In this research, we have proposed an encoder-decoder architecture, Human Trajectory Imputation Model, coined as HTIM, to tackle these challenges. This architecture aims to fill in the missing parts of pedestrian trajectories. The model has been evaluated using the Intersection drone inD dataset, containing trajectory data at suitable altitudes preserving naturalistic pedestrian behavior with varied dataset sizes. To assess the effectiveness of our model, we have utilized L1, MSE, Quantile and ADE loss. Our experiments have demonstrated that HTIM outperforms the majority of the state-of-the-art methods in this field, thus indicating its superior performance in imputing pedestrian trajectories.

In the present study, a multilayer high barrier thin blown film based on a polybutylene adipate terephthalate (PBAT) blend with polyhydroxyalkanoate (PHA), and composed of four layers, including a cellulose nanocrystals (CNC) barrier layer and an electrospun poly(3-hydroxybutyrate-co-3-hydroxyvalerate) (PHBV) hot-tack layer, was characterized in terms of surface roughness, surface tension, migration, mechanical and peel performance, barrier properties and disintegration rate. The results showed a material with a smooth surface. The overall migration test showed that the material was suitable for its use as a food contact layer. The addition of the CNC interlayer had a significant effect on the mechanical properties of the system, drastically reducing the elongation at break and, thus, the flexibility of the material. However, the material retained its elastic modulus and tensile strength. The CNC coating had a negative impact on the peeling strength, weakening the inherently strong interlayer adhesivity of the electrospun PHBV fibers. The multilayer had a good barrier to water vapor, and especially to oxygen, with its permeance reduced by up to a 90 % when the CNC layer was present. Finally, the monolayer blend film disintegrated in a period of less than 55 days in a laboratory-scale composting experiment, while the multilayer system disintegrated in 60 days. Overall, the multilayer system formed a fully compostable structure with great potential for use in food packaging applications.

Design plays a critical role and creates a positive user experience, establishing a solid brand identity and staying competitive in the digital world. This research investigates the impact of user data collecting and analysis in improving user experience. The Data-driven User interface design can create an optimized and relevant UI with individual preferences, which leads to increasing user engagement and usability. The proposal explores methodologies to implement data collection and user research for tailoring digital products.

The United Nations Sustainable Development Goals call for the eradication of poverty, and China has proposed the Rural Revitalization Strategy based on the achievements of its poverty alleviation efforts in 2020. As a vital component of this strategy, the impact of land transfer on farmers' income growth has become a hot topic in both theoretical and practical sectors. This paper utilizes data from the CFPS database for the years 2010-2018 to construct OLS regression models and a Heckman two-stage model to analyze the effects of land transfers on the incomes of different types and sources among farmers. The empirical results show: First, land transfers do promote income growth among farmers, but the effect is primarily positive for those transferring out land, with negligible impact on those acquiring land. Second, the impact of land transfers varies between different types of income for transferees and transferors. Wage income contributes up to 88.26% to the income growth of transferors, a significantly higher rate than the decrease in business income; however, the increase in business income for transferees does not offset the decline in wage income, leading to no significant change in overall income. Further sensitivity analysis using the Heckman two-stage model confirms the robustness of these findings. The conclusions of this study provide theoretical and empirical evidence to optimize land transfer policies, enhance participation in land transfers, and ultimately achieve the mission of rural revitalization.

An electrochemical bioassay based on the rotating droplet electrochemistry by using electron transfer mediator was developed for the evaluation of a wide variety of pollutants such as antibiotics, heavy metals and pesticides in the water environment. Ferricyanide was used as electron transfer mediator for obtaining the catalytic response of Escherichia coli. The electrochemical response of E.coli was measured via hydrodynamic chronoamperometry in a microdroplet on a screen-printed carbon electrode (SPCE). The constructed electrode system successfully evaluate the catalytic response of E.coli solution in presence of ferricyanide. The assay for antibiotic toxicity on E.coli was carried out. The EC50 for ampicillin, sulfamonomethoxine, chlorotetracycline, tetracycline and oxytetracycline valuated by the pre-incubation method were 0.26, 0.77, 5.25, 18.5, 19.0 µM, respectively. The toxicity order was ampicillin > sulfamonomethoxine > chlorotetracycline > tetracycline>oxytetracycline. The proposed method can be used to evaluate the antibiotic toxicities in different real sample, such as pond water, powder and raw milk. Recoveries were found in the range 90 and 99%. The developed methods do not require additional incubation time to evaluate toxicity.

A reliable and efficient rail track defect detection system is essential for maintaining rail track integrity and avoiding safety hazards and financial losses. Eddy current (EC) testing is a non-destructive technique that can be employed for this purpose. The trade-off between spatial resolution and lift-off should be carefully considered in practical applications to distinguish closely spaced cracks such as those caused by rolling contact fatigue (RCF). A multi-channel eddy current sensor array has been developed to detect defects on rails. Based on the sensor scanning data, defect reconstruction along the rails is achieved using an inverse algorithm that includes both direct and iterative approaches. In experimental evaluations, the EC system with the developed sensor is used to measure defects on a standard test piece of rail with a probe lift-off of 4-6 mm. The reconstruction results clearly reveal cracks at various depths and spacings on the test piece.

In this paper, we introduce the notion of the generalized $w$-group inverse in a Banach algebra with proper involution. This is a natural generalization of generalized (weak) group inverse in Banach *-algebras. Many elementary properties of such new weighted generalized inverse are presented. We further establish the equivalent relations between generalized weighted group inverse and weighted generalized Drazin inverse. Related properties of generalized (weak) group inverse are extended to the wider cases.

Modified mRNAs (modRNAs) are an emerging delivery method for gene therapy. In particular, the modRNA-based COVID-19 vaccines have proven that modRNA is a safe and effective therapeutic tool. Moreover, modRNA has the potential to treat various human diseases including cardiac dysfunction. Acute myocardial infarction (MI) is a major cardiac disorder that currently lacks curative treatment options. MI is commonly accompanied by fibrosis and impaired cardiac function. Our group previously demonstrated that the matricellular protein CCN5 inhibits cardiac fibrosis (CF) and improves cardiac dysfunction. However, it remains elusive whether the early intervention of CF under stress conditions is beneficial or more detrimental due to potential adverse effects such as left ventricular (LV) rupture. To obtain acute CCN5 expression, we used modRNA-mediated gene transfer in a mouse MI model. To evaluate CCN5 activity, we established two independent experimental schemes: 1) preventive intervention and 2) therapeutic intervention. Cardiac function and structural changes were measured by echocardiography and magnetic resonance imaging. Finally, fibrosis and the underlying molecular pathway were analyzed by western blotting, quantitative real-time polymerase chain reaction, and immunohistochemistry. The modRNA-CCN5 gene transfer successfully ameliorated CF and enhanced cardiac function in both preventive and therapeutic interventions without LV rupture or any adverse cardiac remodeling. Conclusively, early intervention in CF by modRNA-CCN5 gene transfer is an efficient and safe therapeutic modality for treating MI-induced heart failure without adverse structural remodeling.

This paper presents a comparative study of heat transfer performance of lattice structured heat sinks. 20 different unit cells were chosen and heat sinks were modelled in nTop with constant unit cell size. Al 6061 alloy was chosen for analysis due to its good thermal conductivity, low weight, low cost, and high strength. Steady state thermal analysis was performed using ANSYS with constant input parameters for all samples. Heat flux and temperature distribution within the heat sinks were analysed. The study aims to provide a comprehensive understanding of the thermal performance of lattice heat sink designs.

Being forced to live in an area following a catastrophic landslide may adversely impact people's mental well-being. Unprivileged communities such as Adivasis, Dalits, plantation workers, and people with low incomes in Kerala's hilly districts are forced to live in landslide-affected areas despite their fear. This paper examines the fears and concerns of landslide survivors from the marginalized sections of society from a broader framework of the political economy of mental health. This approach aligns with the assertion made by the World Health Organisation that individual factors do not solely determine mental health but are intricately linked to broader social, political, and economic circumstances. Data were collected through in-depth interviews with fatal landslide survivors and key informants [ ]. The study employed thematic data analysis from in-depth interviews of various fatal landslide survivors since 2018. The three major themes unveiled in the analysis are: 1. post-disaster fears, 2. The factors that triggered fear and concern and 3. Socio-economic marginality and mental health. The study asserts that individuals who are poor and unprivileged are highly susceptible to mental health issues associated with landslides.

Crop production in Afghanistan suffers from limited phosphorus (P) availability, which severely hinders national agriculture sustainability. This present study hypothesized that deep fertilizer placement could significantly enhance uptake of immobile P and thus tissue P accumulation and crop yield. A two-year pot experiment growing two maize (Zea mays) hybrid cultivars (Xida-789 and Xida-211) was therefore conducted to test these hypotheses under three contrasting fertilizer placement methods (broadcast, side band, and deep band). In doing so, P concentrations in both maize tissues and soils were compared at 45, 60, and 115 days after sowing (DAS) under nine combinations of nitrogen (N) and P fertilizer rates (kg ha-1: N112P45, N112P60, N112P75, N150P45, N150P60, N150P75, N187P45, N187P60, N187P75). Results have shown that deep band placement significantly increased P uptake efficiency, leading to greater P concentration and accumulation in maize tissues compared to other two fertilization methods. This improved P uptake was attributed to several factors associated with deep placement, including reduced P fixation, enhanced root access to P, and moisture availability for P uptake. Additionally, deep band placement combined with higher N application rates (N187 and N150) further enhanced plant P uptake by promoting P availability and utilization mechanisms. Deep band placement also resulted in significantly higher total soil P, Olsen-P, and P use efficiency than broadcast and side band methods, indicating a more efficient P fertilization strategy for maize that can improve growth and yield. This present study also found positive correlations between P concentration in plant organs and soil Olsen-P, highlighting the importance of adequate soil P levels for optimal plant growth. Overall, our results have showed that deep band fertilizer placement emerged as a superior strategy for enhancing P uptake efficiency, utilization, and maize productivity compared to broadcast and side band placement. This approach can potentially optimize P fertilizer utilization, improve maize growth and yield, while minimizing environmental P losses associated with broadcast applications.

The continuous casting process of helical fiber reinforced metal matrix composites was proposed, and the experimental equipment was designed and manufactured. The relationship model be-tween the process parameters and the helical shape of the fibers in the metal matrix is analyzed by differential geometry. Helical carbon fiber reinforced lead matrix composites were prepared under different conditions. When the melting temperature and cooling intensity were increased, the helical radius of helical carbon fiber in lead matrix was increased. When the fiber rotation speed was increased, the helical radius was decreased, and the helical pitch was de-creased proportionally. The experimental results are consistent with the process model. Carbon fiber rein-forced aluminum composites were prepared. Scanning electron microscopy showed that the infiltration between the aluminum matrix and the carbon fiber was not complete. As the volume fraction of carbon fiber which was added in composites is too small, the mechanical properties of the composites have not been significantly improved.

It is shown that if there exists in nature a pair of heavy elementary particles each with a charge equal to that of the proton and with mass energy , then their direct interaction gives rise to a spontaneous fractionation of the two charges into three pairs of elementary particles according to two equiprobable channels, one hadronic and one leptonic. The leptons and quarks produced are in agreement with the first generation of the Standard Model of matter. Fractionation suggests the relative abundances of the elementary particles, introducing some questions about the possibility of the real existence of a currently unknown particle and its role in the formation of an apparent matter-antimatter asymmetry in the universe.

This communication explores the transition from Cognitive Behavioural Therapy (CBT) to a more holistic model, named Complex Therapy, developed by Tullio Scrimali for explaining and treating mental disorders. The Author delves into the limitations of traditional CBT and introduces an innovative framework that integrates multiple therapeutic modalities. While CBT is based on the study and modification of behaviour and cognition, Complex Therapy includes, in its focus, the theory of human relationships, the attachment theory, neuroscience, applied neuroscience, complex systems theory and ecology.Complex Therapy addresses the multifaceted nature of mental health issues by combining evidence-based techniques with personalized care strategies. The goal is to enhance patient outcomes through a tailored, comprehensive treatment plan that adapts to the evolving needs of individuals facing mental health challenges.Two innovative and original items which Scrimali has developed, which are a device for Applied Neuroscience MindLAB Set and a new botanical drug, NegEnt, are presented and discussed.The topic also describes, an original and integrated protocol, named Negative Entropy, the author has developed for treating a challenging disorder, such as schizophrenia, he renamed Entropy of Mind.

Inadequately managed agricultural waste significantly impacts the environment, health, and economy. This form of pollution arises from the underutilization, poor awareness, and insufficient treatment of agricultural waste. Fruit and vegetable wastes are valuable sources of bioactive compounds. This study aims to revalorize discarded waste from red habanero chili peppers (Capsicum chinense) by extracting bioactive compounds through different extraction processes: maceration (ME), maceration assisted by ultrasound (US), Soxhlet extraction (SE), supercritical fluid extraction (SFE), and supercritical fluid extraction with a co-solvent (SFEC). Extraction processes have significant effects on extraction efficiency and phytochemical profile (capsaicinoids and carotenoids recovery). The results indicate that the highest efficiency process is obtained with SFEC, also a high phytochemicals recovery (14.9 mg of total capsaicinoids and total carotenoids 292.09 µg per gram of sample). Concerning to phytochemical profile in the extract, the maceration process gets the highest concentration of compound followed by US and SFEC. These data reveal that the use of SFE and SFEC extraction is recommended for extraction of phytochemicals with biologically activity from red habanero chili pepper waste for diverse industries application.

Optimal control is a critical tool for mechanical robotic systems, facilitating precise manipulation of dynamic processes. These processes are described through differential equations governed by a control function, addressing a time-optimal problem with bilinear characteristics. Our study utilizes the classical approach complemented by Pontryagin's Maximum Principle (PMP) to explore this inverse optimal problem. The objective is to develop an exact piecewise control function that effectively manages trajectory control while considering the effects of viscous friction. Our simulations demonstrate that the proposed control law markedly diminishes oscillations induced by boundary conditions. This research not only aims to delineate the reachability set but also strives to determine the minimal time required for the process. The findings include an exact analytical solution for the stated control problem.

Energy from biogas is one of the most promising renewable energy sources. Significant, for technical, economic, and environmental reasons, is the construction of agricultural microgas plants next to households specialising in cattle rearing. The availability of free substrate makes it possible not only to produce one's electricity and heat but also to produce a more environmentally and human-friendly manure. The operation of biogas plants is, unfortunately, associated with technical problems. This paper presents the results of a study of the quality of electricity generated in an agricultural biogas plant built at a farm specialising in dairy cows, where the owner reported a problem with the voltage in the power supply network. Therefore, selected power quality parameters occurring at the connection point of the biogas plant were analysed in detail. As the authors' research showed, in the case in question, the agricultural biogas plant was connected via a cable with too small a conductor cross-section, which resulted in significant voltage exceedances, making it impossible to switch on the second of the biogas plant's generators. Replacement of the feed-in cable has enabled both generators to run, but significant fluctuations in the feed-in voltage values were still noticeable. Analysis of the subsequent measurements revealed the need for changes in the design of the digester itself. The proposal for change is to replace the two current digester mixers (each rated at 9 kW) with more mixers of lower power. The new mixers would operate in an alternating system, where only one would always be activated.

Open-vocabulary learning has recently gained prominence as a means to enable image segmentation for arbitrary categories based on textual descriptions. This advancement has extended the applicability of segmentation systems to a broader range of generally purpose scenarios. However, current methods often revolve around specialized architectures and parameters tailored to specific segmentation tasks, resulting in a fragmented landscape of segmentation models. In response to these challenges, we introduce OVAMTSeg, a versatile framework designed for Open-Vocabulary and Multitask Image Segmentation. OVAMTSeg harnesses adaptive prompt learning to empower the model to capture category-sensitive concepts, enhancing its robustness across diverse multi-task and scenario contexts. Text prompts are employed to effectively capture semantic and contextual features of the text, while cross-attention and cross-modal interactions enable the fusion of image and text features. Furthermore, a transformer-based decoder is incorporated for dense prediction. Extensive experimental results underscore the effectiveness of OVAMTSeg, showcasing its state-of-the-art performance and superior generalization capabilities across three segmentation tasks. Notable achievements include a 47.5 mIoU in referring expression segmentation, 51.6 mIoU on Pascal-VOC with four unseen classes, 46.6 mIoU on Pascal-Context in zero-shot segmentation, 65.9 mIoU on Pascal-5i, and 35.7 mIoU on COCO-20i datasets for one-shot segmentation.

Degenerative disc disease (DDD) is a pervasive condition that limits quality of life and burdens economies. Traditional pharmacological treatments aimed at slowing degeneration are ineffective in the long-term. Orthobiologics, regenerative agents derived from the patient’s own tissue, are a promising emerging therapy for degenerative disc disease. This review first outlines the pathophysiology of degenerative disc disease, highlighting the limitations of existing treatments and explores the orthobiologic tools for treating degenerative disc disease (platelet-rich plasma, mesenchymal stem cells). Their history in regenerative medicine is outlined, demonstrating how in vitro evidence informed preclinical animal studies on their efficacy in treating degenerative disc disease. Finally, clinical trials utilizing these treatment options are reviewed and directions for future research are outlined. Although the current clinical evidence available is limited to propagate their routine clinical usage the field holds immense potential in the management of DDD. There is room for these treatments to be optimized for effective consistent clinical outcomes in DDD.

We introduce the notion of generalized contraction on dualistic partial metric spaces. A fixed point theorem for mappings satisfying above mentioned contraction is obtained. Some consequences of our result are obtained. We construct an example to demonstrate the effectiveness of our result among the corresponding results in partial metric spaces. Our results provide substantial generalizations and improvements of several well known results existing in the comparable literature. We discuss an application of our fixed point results to show the existence of solution of functional equations.

The measures related to climate change and international technology transfer have been closely intervened as most international environmental instruments, including the United Nations Framework Convention on Climate Change and Kyoto Protocol as well as Paris Agreement which contain the provisions concerning environmentally friendly technology transfer. However, technologies have not been transferred adequately owing to the flaws in the relevant provisions and due to the fact that most technologies are possessed by transnational corporations and other private sectors. In order to undertake the commitment by the governments of developed countries and at the same time, to conform the commercial activities of their respective private sectors to the level of promised international obligation, an uniform international technology transfer agreement needs to be established separately, particularly under the World Trade Organization regime in Post Pairs-Agreement era. This paper first explores the defects and challenges found in provisions related to technology transfer in existing environmental agreements, and examines the possibilities of concluding an international technology transfer agreement both from theoretical and practical perspectives. climate change;environmentally sound technology;international technology transfer;Post Paris-Agreement Era

Businesses use technological and social media marketing to respond to the Covid-19 pandemic. This study aims to understand better the factors that impact the spread of new technologies, the effectiveness of social media advertising, and the longevity of businesses. The study used a quantitative strategy based on partial least squares structural equation modeling to learn about the phenomenon of interest as much as possible. Dhaka, Bangladesh, small and medium-sized businesses participated in the survey. According to the findings, the popularity of internet and e-business technologies may be attributed to their apparent usefulness and ease of use. It is connecting internet/e-business technology, social media marketing, and the long-term success of small and medium-sized enterprises. Still, the expense factor was insufficient to prove that SMEs engage in social media advertising. Mediating effects between components may be better understood via internet/e-business technology and social media marketing, as shown by this study. This study is the first of its kind in Bangladesh and sheds light on the resilience of SMEs in the face of the Covivirus-19 pandemic, notwithstanding its focus on the capital city of Dhaka.

This article introduces a novel nature-inspired metaheuristic algorithm called Frilled Lizard Optimization (FLO), which emulates the hunting behavior of frilled lizards in their natural habitat. FLO draws in-spiration from the sit-and-wait strategy observed in frilled lizards during hunting. The underlying theory of FLO is presented and mathematically formulated in two phases: (i) an exploration phase, simulating the frilled lizard's attack towards prey, and (ii) an exploitation phase, simulating the lizard's retreat to the top of the tree after feeding. To assess FLO's efficacy in solving optimization problems, the algorithm's performance is evaluated across fifty-two standard benchmark functions, encompassing unimodal, high-dimensional multimodal, fixed-dimensional multimodal, and the CEC 2017 test suite. Comparative analyses with twelve existing metaheuristic algorithms are conducted. The simulation results reveal that FLO, distinguished by its adeptness in exploration, exploitation, and balancing them during search process, outperforms competing algorithms. Additionally, FLO is implemented on twenty-two constrained optimization problems from the CEC 2011 test suite and four engineering design problems, demonstrating its effectiveness in addressing real-world optimization applications.

Background: Post-acute sequelae of SARS-CoV-2 infection (PASC) is a complicated disease that affects millions of people all over the world. Previous studies have shown that PASC impacts 10% of SARS-CoV-2 infected patients of which 50-70% are hospitalized. It has also been shown that 10-12% of those vaccinated against COVID-19 were affected with PASC and its complications. The severity and the later development of PASC symptoms is positively associated with the early intensity of the infection. Results: The generated health complications caused by PASC involve a vast variety of organ systems. Patients affected by PASC have been diagnosed with neuropsychiatric and neurological symptoms. Cardiovascular system also has been involved and several diseases such as myocarditis, pericarditis, and coronary artery diseases were reported. Chronic hematological problems such as thrombotic endothelialitis and hypercoagulability were described as a condition that could increase the risk of clotting disorders and coagulopathy in PASC patients. Chest pain, breathlessness, and cough in PASC patients were associated with respiratory system in long COVID-19 causing respiratory distress syndrome. The observed immune complications were notable, involving several diseases. Renal system also was impacted and result in raising the risk of diseases such as thrombotic issues, fibrosis, and sepsis. Endocrine gland malfunction can lead to diabetes, thyroiditis, and male infertility. Symptoms such as diarrhea, nausea, loss of appetite and taste were also among reported observations due to several gastrointestinal disorders. Skin abnormalities might be an indication of infection and long-term implications such as persistent cutaneous complaints were linked to PASC. Conclusions: Long COVID is a multidimensional syndrome with considerable public health implications, affecting several physiological systems and demanding thorough medical therapy as well as more study to address its underlying causes and long-term effects.

Aiming at the problems of inaccurate segmentation of long object and information loss of small object in real-time semantic segmentation algorithm, this paper proposes a lightweight multi-branch real-time semantic segmentation network based on BiseNetV2. The new auxiliary branch makes full use of spatial details and context information to cover the long object in the field of view. Meanwhile, in order to ensure the inference speed of the model, the asymmetric convolution is used in each stage of the auxiliary branch to design a structure with low computational complexity. In the multi-branch fusion stage, the alignment and fusion module is designed to provide guidance information for deep and shallow feature mapping, so as to make up for the problem of feature misalignment in the fusion of information at different scales, and thus reduce the loss of small target information. In order to further improve the model’s awareness of key information, a global context module is designed to capture the most important features in the input data. The proposed network uses NVIDIA GeForce RTX 3080 Laptop GPU experiment, on the road street view data set Cityscapes and CamVid average occurring simultaneously ratio reached 77.1% and 78.4% respectively, with running speed of 127 frames/s respectively and 112 frames/s. The experimental results show that the proposed algorithm can achieve real-time segmentation and improve the accuracy significantly, showing good semantic segmentation performance

The nutrient absorption and utilization efficiency in the roots of seedlings are beneficial for increasing crop yield. Creating marker assisted selection for wheat root traits can assist wheat breeders in choosing robust roots to maximize nutrient uptake. Exploring and identifying the effect of different nitrogen applications on RSA is of great significance for breeding nitrogen efficient wheat varieties. In this study, A total of 243 wheat varieties native to the Yellow and Huai Valley regions of China were utilized for genome-wide association studies (GWAS). Furthermore, a recombinant inbred line (RIL) population of 123 lines derived from the cross between Avocet and Chilero was utilized for linkage examination and confirmation of the hereditary loci distinguished by GWAS. Five RSA traits include the relative number of root tips (RNRT); relative total root length (RTRL); relative total root surface area (RTRS); relative total root volume (RTRV) and relative average root diameter (RARD) where evaluated under two N conditions—normal N (NN) supply and low N (LN)—to characterize the NUE of each accession. GWAS and linkage analysis were performed by integrating data from the wheat 660k single nucleotide polymorphism (SNP) chip and diversity arrays technology (DArT) to identify genetic loci associated with RSA. The results showed that based on the ratio of RSA related traits under two N supply conditions, a total of 598 SNP markers, which are significantly associated with RSA related traits, were detected at 160 genetic loci by GWAS. A total of 10 QTL loci related to RSA were dis-covered and identified by linkage mapping. In which, three significant RSA related Quantitative Trait Locus (QTL) were identified, namely qRtrl-3D, qRnrt-3D, and qRtrl-7D. The study has the potential to enhance the effectiveness of selecting root traits in wheat breeding programs, offering valuable insights into the genetic underpinnings of nitro-gen use efficiency (NUE) in wheat. This could lead to the creation of NUE wheat varieties by implementing focused breeding strategies

With the increasing concern of environment, the energy-efficiency scheduling of manufacturing industry is becoming urgent and popular. In turning processes, both spindle speed and processing time can affect the final energy consumption and thus the spindle speed and scheduling scheme need to be optimized simultaneously. Since the turning workshop can be regarded as the flexible flow shop, this paper formulates a mixed integer linear programming model for energy-efficient scheduling of flexible flow shop. Accordingly, a new decoding method is developed by considering of the optimization of spindle speed and scheduling scheme simultaneously, and an estimation of distribution algorithm adopting the new decoding method is proposed to solve large-size problems. The parameters of this algorithm are determined by statistical technique with a simplified practical case. In order to validate the proposed method, a case from practical factories is studied, in which the makespan can be shortened by 25.22%, and the consumed energy can be saved by 5.48%. These results demonstrate the effectiveness of the proposed mathematical model and algorithm.

The relationship between nations is largely seen as a peripheral issue in the recent history of political philosophy and in the majority of discussions of political philosophy issues today. The idea of a universal natural state were countries are seen as essentially self-sufficient, functional units, and have been proposed to represent the relative lack of moral standards guiding relationships between nations. At one extreme of the tradition, international thought has substituted raison d'état being the highest norm for any universal laws governing relations between states, a view embodied by Machiavelli, Rodin, and others and Hobbes , The lack of supranational political powers has led to the conclusion that, even in cases where the possibility of international moral relationships has been acknowledged, such as in post-Grotian publications on international law, these ties are significantly weaker than in-tranational social bonds. The justification and aversion to war—the primary mode of social in-teraction in the natural condition of the world—is the only issue in the field of global relations to have received substantial theoretical study. Even though this disregard was justified in the past, a number of recent events force us to re-consider the "recalcitrance of international affairs to being theorized about."2. The growing gap between both prosperous and impoverished nations; the emergence of centers of economic in-fluence beyond the reach of effective state regulation; the emergence of severe food and energy shortages brought on, at least in part, by national governments' pursuit of disorganized and uncontrolled growth policies; the growing sensitivity of domestic Countries to the outside eco-nomic, political, and cultural events are some of these developments , requests from third-world nations for greater equal access to international politics and economy. To put it in terms more familiar to conversations about this topic, the rise of "low politics" in negotiation and "welfare questions" within global forums corresponds with the growing influence of transnational con-nections and international agreements on human well-being. Not because "high politics"—that is, the threat and prevention of war—has lost significance; rather, it is just one issue among many for which international cooperation is now required in order to find answers.

Crop productivity is directly dependent to soil fertility. High soil organic carbon (SOC) content in soil is vital as it leads to improved soil quality, increased productivity, and stable soil-aggregates. In addition, with the signing of the climate agreement, there is growing interest in carbon sequestration in landscapes. This paper looks at how SOC can be increased so that it not only contributes to reduction of CO₂, but also translates to increased food production thereby enhancing food security. This synergy between mitigation and enhancing food security is even more relevant for mountain landscapes of the Hindu Kush Himalayan (HKH) region where there remains huge potential to increase CO₂ sequestration and simultaneously address food security in the chronic food deficit villages. Soil samples were collected from seven transects each in Bajhang and Mustang and from 4 land use types in each transect. Samples of soils were taken from two depths in each plot; 0-15 cm below the soil surface and 15-30 cm below the soil surface to compare the top soil and subsoil dynamics of the soil nutrients. The lab analysis was performed to assess the soil texture, soil color, soil acidity in 'power of hydrogen' (pH), macro-nutrients as soil fertility. Secondary data was used to analyze the level of food deficit in the villages. The result shows that most of the sample soils from Mustang were clay (82.1%) which is 46 samples out of 56. The pH value of soil from Bajhang ranged from 5.29 to 9.09. The pH value of soil ranged from 5.65 to 8.81 in Mustang. SOC contents of sampled soils from Bajhang ranged from 0.20% to 7.69% with mean amount of 2.47% ± 0.17. SOC contents of sampled soils from Mustang ranged from 0.51% to 8.56% with mean amount of 2.60% ± 0.25. By land use type, forest land had the highest carbon (C) content of 53.61 t ha^-1 in Bajhang whereas in Mustang, agricultural land had the highest C content of 52.02 tons ha-1. Based on these data, we can say that there is potential for increasing SOC through improved soil health and crop production and soil. Sustainable soil management should be practiced for higher productivity. Livestock may also provide farmyard manure, which can be used to fertilize cultivated soils, which increases soil productivity. Increasing productivity would aid in increasing the access and availability of food in these mountain villages.

Carotid atherosclerotic lesions are a major cause of cerebrovascular disease (CVD). Identification and quantification of carotid plaques are important for categorizing the vulnerability of plaques for rupture and assessing the impact of treatments. The irregularity of plaque surface is associated with previous plaque rupture and plays an important role in the risk of stroke. Thus, the aim of this study is to develop and validate novel vulnerability biomarkers from three-dimensional ultrasound (3DUS) images by analyzing the surface morphological characterization of carotid plaque using fractal geometry features. 3D box-counting and 3D blanket are the two types of 3D fractal dimension that were employed to describe the smoothness of plaques. This fractal dimension analysis tool was used to evaluate the effect of atorvastatin using 3DUS carotid images, which were acquired from 6 patients treated with atorvastatin with 80 mg daily and 5 patients with placebo. The Student's T Test results showed that those two fractal features were effective for detecting the statin-related changes in carotid atherosclerosis with p<0.0068 and p<0.015 respectively, suggesting that 3D fractal dimension measurements can be used effectively to analyze the surface characteristics of carotid plaques, especially for evaluating the impact of the treatment.

VITEK MS PRIME (bioMerieux), a newly developed Matrix-assisted laser desorption ionization time-of-flight mass spectrometry (MALDI-TOF MS) system, alongside VITEK PICKME Pen (PICKME), offers easy sample preparation for bacteria and yeast. VITEK MS PRIME also offers two software platforms for filamentous fungi: the IVD database and the RUO database. Our study evaluated its identification agreement on 320 clinical isolates of bacteria and yeasts, comparing PICKME and traditional wooden toothpick sampling techniques against ASTA Mi-croIDSys Elite results. Additionally, we assessed the IVD (v3.2) and SARAMIS (v4.16) RUO data-bases on 289 filamentous fungi against molecular sequencing. The concordant rates for spe-cies-level identification of bacteria and yeasts were about 89.4% (286/320) between the PICKME and wooden toothpick, about 83.4-85.3% between VITEK MS PRIME and ASTA MicroIDSys Elite. Retesting with PICKME improved concordance to 91.9%. For filamentous fungi, species-level identification reached 71.3% with the IVD database and 85.8% with RUO, which significantly enhanced basidiomycetes' identification from 35.3% to 100%. Some strains in the IVD database, like Aspergillus vesicolor, Exophiala xenobiotica, and Nannizzia gypsea failed to be identified. VITEK MS PRIME with PICKME offers reliable and efficient microorganism identification. For fila-mentous fungi, combining the use of the RUO database can be beneficial, especially for basidi-omycetes.

The world is struggling with the increasing rate at which water bodies are constantly polluted due to rapid modernization and industrialization. The different types of water contaminants include both anthropogenic and natural contaminants. Environmentalists are mainly concerned about heavy metals such as cadmium ions, as they are considered poisonous and carcinogenic even if they are present at a minimum concentration, and they are considered an immediate concern, according to the World Health Organization. Recently, many methods, such as solvent extraction, ion exchange, electrochemical precipitation, and reverse osmosis, have been developed to remove heavy metals from wastewater. These methods have been reported to be expensive and inefficient; hence, more cost-effective and eco-friendly alternative strategies are needed. Amidst these challenges, a ray of hope emerges in the form of biosorbents. These abundant, eco-friendly, and cost-efficient materials have shown promise as an alternative method for removing heavy metals from wastewater. They are equipped with functional groups that can effectively absorb metal ions onto their surfaces, offering a potential solution to our water contamination woes. This review is significant as it delves into the potential use of several biosorbents to decontaminate cadmium ions from wastewater. This review is significant as it delves into the potential use of several biosorbents to decontaminate cadmium ions from wastewater

Cymbidium faberi Rolfe is one of the traditional Chinese orchids with important ornamental value, and the cultivation of Cymbidium faberi Rolfe mutant strains with different appearances is essential to increase its economic value, but at present, the acquisition of Cymbidium faberi Rolfe mutant strains basically relies on natural mutation.The objectives of this research were to mutagenize Cymbidium faberi Rolfe protocorm-like bodies (PLBs) and shoots in vitro using sodium azide (NaN3), and to screen and evaluate mutants in mutagenized Cymbidium faberi Rolfe seedlings using morphological characteristics.Cymbidium faberi Rolfe PLBs and shoots were used as mutagenic materials, and co-cultivated in induced shoots growth medium with the addition of 0.0 (control), 0.5, 1.0, 1.5, 2.0, 2.5, 3.0 mg/L and 0.0 (control), 4.0, 5.0, 6.0, 7.0, 8.0, 9.0, and 10.0 mg/L NaN3 to induce the mutations, and the mortality rates of the PLBs and shoots were increased with the increase of the NaN3 concentration.At 14 d of co-cultivation, PLBs and shoots were most efficiently mutagenized with 1.5 mg/L and 4.0 mg/L NaN3, respectively.After the explants were cultured for 3 months, changes in leaf and flower morphology were observed in some mutants: shorter and thicker leaves, shorter node length, reduced height, and mid-translucent leaves compared with controls; and some Cymbidium faberi Rolfe bloomed prematurely, with single flowers with large, thick petal sepals and small inflorescences, and colours include light green throughout, and a few with purple stamens.This suggests that NaN3 can effectively mutagenise Cymbidium faberi Rolfe PLBs and shoots to satisfy people's demand for Cymbidium faberi Rolfe's ornamental properties while increasing its economic value.

Road cracks significantly affect the serviceability and safety of roadways, especially in mountainous terrain. Traditional inspection methods, such as manual detection, are excessively time-consuming, labor-intensive, and inefficient. Additionally, multi-function detection vehicles equipped with various sensors are expensive and not suitable for mountainous roads due to poor conditions. To address these challenges, this study proposes a customized Unmanned Aerial Vehicles (UAV) inspection system designed for automatic crack detection. The system focuses on enhancing autonomous capabilities in mountainous terrains by incorporating embedded algorithms for route planning, autonomous navigation, and automatic crack detection. The slide window method is proposed to enhance the autonomous navigation of UAV flights by generating path planning in mountainous roads. This method compensates for GPS/IMU positioning errors, particularly in GPS-denied or GPS-drift scenarios. Moreover, the YOLOv8 algorithm is introduced to conduct autonomous crack detection from UAV imagery in the offboard module. To validate our UAV inspection system's performance, we conducted several experiments to assess its accuracy, robustness, and efficiency. The experimental results demonstrate that our UAS inspection system accurately estimates the flight trajectory along the mountainous road for autonomous navigation. Furthermore, the experimental detection results also demonstrate that the YOLOv8 algorithm achieves higher recognition accuracy compared to the YOLOv5, and YOLOv7-tiny algorithms, exceeding 3.1%,and 6.8% of mAP, respectively. In summary, the UAV inspection system proposed in this study can provide a useful tool and technological guidance for the regular inspection of mountainous roads.

The challenging terrain and deep ravines characteristic of mountainous regions often result in slower path planning and suboptimal flight paths for Unmanned Aerial Vehicles (UAVs) when traditional meta-heuristic optimization algorithms are employed. This study investigates the application of an Improved Enhanced Snake Optimizer (IESO) for three-dimensional path planning in a simulated rugged mountainous terrain. The initialization process in the enhanced snake optimizer is refined by integrating the Chebyshev chaotic map. Additionally, a non-monotonic factor is introduced to modulate the "temperature," and a boundary condition is incorporated into the dynamic opposition learning mechanism. These modifications collectively reduce the likelihood of population convergence to local optima during optimization. The feasibility of IESO is validated through time complexity and global convergence analyses. Comparative simulation experiments benchmarked IESO against five state-of-the-art optimization algorithms across test functions and path-planning simulated scenarios. The experimental results indicate that the enhanced algorithm achieves superior optimization precision, faster convergence speeds, and improved quality in the planned trajectories by 30%.

To ensure consumers can purchase high-quality rice, accurate identification of rice varieties is particularly important. Methods: This article conducts research based on machine learning algorithms from the perspectives of image, spectrum, and spectrogram fusion. Six types of hyperspectral image data of rice were preprocessed using convolutional smoothing (SG) and multiple scatter correction (MSC). Texture information of the images was extracted using gray-level co-occurrence matrix. Spectra, texture, and spectrogram data were fused into a new matrix. Spectral, texture, and spectrogram fusion data were used as inputs for the model, and support vector machines (SVM), logistic regression (LR), and K-nearest neighbors (KNN) classification models were constructed and compared. Results: From the classification results, the spectrogram fusion classification performance was better than classification models using only spectra or texture. Conclusion: The research results showed that the accuracy of SVM and LR classification models exceeded 90%, and the LR model performed the best, effectively classifying rice varieties.

This study assesses the impact of militarization, industrialization, technological innovation, and energy consumption on CO2 emissions in NATO countries, divided into "traditional" (Group 1) and "new member" states (Group 2), using data from 1985 to 2019. It identifies heterogeneity in effects and dependencies between the groups. Employing Pedroni and Kao panel cointegration tests, a long-term equilibrium relationship among the variables is confirmed. The analysis, using panel ARDL and GMM methods, reveals distinct outcomes for each group. In Group 1, military spending and energy consumption significantly increase CO2 emissions, while industrialization and technological innovation reduce them. Conversely, in Group 2, technological innovation and energy consumption raise emissions, whereas military spending and industrialization decrease them. The findings suggest Group 1 should strategize military expenditure and energy consumption to cut emissions, whereas Group 2 should focus on eco-friendly technology and efficient energy use to achieve environmental sustainability.

Electrochemical methods are used for the treatment of both municipal and industrial wastewater, either independently or in conjunction with biological methods. This conjunction is used for pretreatment or posttreatment of biologically treated wastewater. In our work, we focused on the combination of these processes, where pre-electrolysis was used to produce dissolved iron before the activation process. Electrolysis was also directly introduced into the activation using either iron or carbon electrodes. The surface of one iron electrode was 32.2 cm2, the applied voltage was 21 V, and the supplied current was 270 mA. The surface of one carbon electrode was 7.54 cm2, the supplied current was 82.5 mA, and the applied voltage was 21 V. From laboratory research on the treatment of synthetic municipal wastewater using a combination of electrolysis and activation processes, it resulted that the use of iron electrodes increased the efficiency of phosphorus removal compared to its precipitation with iron salts. The electrolysis had a positive effect on the sedimentation properties of sludge and the destruction of filamentous microorganisms. Electrolysis negatively affected the respiration rates of activated sludge and the efficiency of denitrification. However, it did not have a negative impact on the nitrification activity of the sludge.

The research reported on this paper was aimed at improving the overall efficiency of a PDO certified artisanal cheese production process. Being a PDO certified foodstuff by the EU, it is considered to have properties and qualities determined by the geographical environment in which is made, with its production taking place in a specific and determined geographical location, in this case the Serra da Estrela region. In that sense, the authors conducted a mapping according to a systemic perspective of the processes involved in the context of manufacturing and distribution of certified Serra da Estrela cheese. Numerous methods were used throughout the process, such as a systemic design analysis, and techniques derived from ethnographic methods, which led to the collection of data in the field and consequently provided the immersion of the researcher in genuine work situations. Critical points were identified and emphasized in the systemic map with the purpose of encouraging initiatives to address and overcome the gaps and inefficiencies detected. The systemic design analysis triggered the development of design work. Observations following an ethnographic approach identified ergonomic risks in cheese making during the process of cutting excess chips, fostering the emergence of musculoskeletal disorders at the wrist. A tool that fits best to the task at hand was developed. A prototype of the new tool enabled collecting feedback from use in the work context, in order to inform product development. The domains of agricultural production and microbiology, considering the specific microorganisms developed trough the ripening process of the cheese, turned out to be aspects of high importance for the issue under focus, contributing to a broader understanding of the ripening process and its risks, simultaneously improving the efficiency and success of cheese production. If it were not for the systemic analysis, which served as a link between the boundaries of distinct domains such as the risk of microorganism contamination, ergonomics, energy efficiency, legislation and regulation policies, transportation challenges and economic viability, approached throughout the research. Simultaneously creating bridges between them, the various problems might not have been detected in the first place, as they are usually addressed in specialized disciplines, predetermined by the restrictions of each specific area of knowledge. As a consequence of the development of this research, which was based on an analysis that sought to establish possible connections between various disciplines and tried to constantly maintain a holistic perspective, making new connections and observing the issues from a new angle, apart from the already established methodologies. All this allowed to lay out the seeds for the development of a plan to tackle the critical points identified by the systemic analysis reported in this paper.

Statistical denoising techniques have been well studied, however many challenges still remain. This 9 article focuses on determining the least necessary number of significant samples in a statistical pop-10 ulation sampling, while minimizing the impact on the statistical detection of the fiber Bragg grating 11 (FBG) power spectra. This is achieved by using Bayesian decision making, small population statis-12 tics while excluding false detection. First, we investigate the impact of two-sided sliding window 13 technique applied near the cell under the test. The window size varies from 8 to 60 samples. The 14 considered maximum size of population sampling is connected with the number of wavelength 15 samples within the bandwidth of the symmetrical FBG power spectra peaks. Regarding the sym-16 metry of FBG power spectra peaks and the possible reduction of computational demands, we inves-17 tigate the impact of a one-sided sliding window. This enables to achieve less processing latency for 18 real time applications thus brings benefits to FBG-based fiber optical sensing. Both, two- and one-19 sided small population sampling techniques are then experimentally verified. Detection results are 20 analyzed in depth via calculating detection thresholds by using the small size window sliding along-21 side the waveband. From results achieved, it was found that the normality three-sigma rule does 22 not need to be followed while using the small population sampling. Experimental demonstrations 23 and analyses showed that the proposed concept of denoising and statistical threshold detection 24 based on the sliding window does not depend on the prior knowledge of probability distribution 25 functions of the FBG power spectra peaks level and background noise. We have also found that the 26 thresholds’ adaptability mainly depends on the statistical numerical characteristics of the above ad-27 ditive mixture of the FBG power spectra peaks signals and background noise.

Panax notoginseng is a traditional Chinese medicine, and saponins are its main active ingredients. The content of saponins in flower of P. notoginseng is the highest in the whole plant. Minor ginsenosides have stronger pharmacological activity than main ginsenosides, but its content in nature is very low. We can use extracted total saponins from P. notoginseng flower as the substrate to produce minor ginsenosides by biotransformation method. In this study, we used the fungus Talaromyces flavus and its crude enzymes to transform the extracted total saponins of P. notoginseng flower. Through the qualitative and quantitative analysis of the transformation substrates and products, it was found that minor ginsenosides Gyp-XVII, ginsenosides C-Mc1, C-Mx1, F2, Rg3, 20(R)-Rg3, Rk1 and Rg5 were found in the products and the conversion rate of the major saponins in P. notoginseng flower ranged from 44.16 to 55.22%, the yields of the minor ginsenosides ranged from 0.05 to 3.24%. This study provided a good experimental idea, greatly increased the utilization rate of total saponins in P. notoginseng flower, and laid a foundation for promoting the wide application of minor saponins.

Plant-based essential oils are important natural products rich in volatile compounds, and they have various applications in medicine, food, perfumery and cosmetics. These substances can be produced using various methods, such as steam distillation and solvent extraction. Their chemical composition is influenced by geographical and climatic conditions, production methods, and intrinsic factors. Published articles and literature were scanned to gather the required information. Previous studies have shown that essential oils possess chief health benefits, including antimicrobial, anti-inflammatory, antioxidant, and psychological effects. Consequently, they have wide applications in the food industry as preservatives in food systems and in active packaging, edible coating, probiotic foods, and flavoring. Essential oils can be successfully utilized in flavoring foods and beverages such as cheese, ice cream, and soft drinks. Despite their great antimicrobial and flavoring roles, it is important to further investigate their possible interactions with food components and the physiochemical characteristics of foods flavored with essential oils.

Quantitative determination of the critical size of inclined coal pillar in old goaf water affected area is of great significance for water damage prevention and safe mining. The critical size of inclined waterproof coal pillar is derived by using theoretical analysis, numerical calculation and field engineering practice for the stability of the waterproof coal pillar in old goaf water affected area of 1303 working face of Dananhu I mine in Xinjiang region. Firstly, a force model of inclined waterproof coal pillar was established to reveal the law that the critical size of the coal pillar increases with the increase of coal seam inclination under the action of asymmetric load. Then, numerical simulation was applied to reveal the dynamic evolution process of plastic deformation-destabilization-destruction of section coal pillar under the influence of mining and single-side water pressure, and the critical size of waterproof coal pillar in study area was determined to be 19.09m. Finally, measures such as pumping and pressure relief and slurry reinforcement were adopted to reduce the deformation rate of the roadway on side of waterproof coal pillar, which ensured the stability of the coal pillar and roadway and the safe recovery of the working face.

This study investigates the impact of specimen size on the mechanical properties of wood, specifically focusing on compression strength, elastic modulus, and Poisson's ratio. Compression tests were conducted using three different specimen sizes (20mm×20mm×30mm, 40mm×40mm×60mm, 60mm×90mm×90mm) in the longitudinal, radial, and tangential directions. Mechanical parameters, failure mechanisms, load-displacement curves, and stress-strain relationships were systematically analyzed for each size. The study also evaluated the influence of specimen size on the accuracy of finite element numerical simulations by utilizing the obtained mechanical parameters. The results reveal a significant correlation between compressive strength and specimen size, indicating a decrease in compressive strength with increasing specimen size. Conversely, elastic modulus and Poisson's ratio exhibit less sensitivity to variations in specimen size. Notably, parameters derived from small-sized specimens (20mm×20mm×30mm) exhibited substantial errors, while those obtained from medium-sized (40mm×40mm×60mm) and large-sized specimens (60mm×90mm×90mm) demonstrated greater reliability, providing precise results in finite element numerical simulations.

In recent decades, with the ever-growing scale of video data, near-duplicate videos continue to emerge. Data quality issue caused by near-duplicate videos is becoming more and more prominent, which has affected the application of normal videos. Although current studies on near-duplicate video detection can be helpful to uncover data quality issues for videos, they still lack a process of automatic merging for the video data represented by high-dimensional features, which are difficult to automatically clean the near-duplicate videos to improve data quality for video datasets. At present, there are few studies on near-duplicate video data cleaning. The existing studies have the sensitive problems of video data orderliness and clustering initial center under a condition that prior distribution is unknown, which seriously affect the accuracy of near-duplicate video data cleaning. To address the above issues, an automatic near-duplicate video data cleaning method based on a consistent feature hash ring is proposed in this paper. First, a residual network with convolutional block attention modules, a long short-term memory deep network, and an attention model are integrated to construct an RCLA deep network with the multi-headed attention mechanism to extract spatiotemporal features of video data. Then, a consistent feature hash ring is constructed, which can effectively alleviate the sensitivity of video data orderliness while providing a condition of near-duplicate video merging. To reduce the sensitivity of the initial cluster centers to results of near-duplicate video cleansing, an optimized feature distance-means clustering algorithm is constructed by utilizing a mountain peak function on a consistent feature hash ring, which can implement automatic cleaning of near-duplicate video data. Finally, experiments are conducted based on a commonly used dataset named CC_WEB_VIDEO and a coal mining video dataset. Compared with some existing works, simulation results demonstrate that the performance of the proposed method.

Iron tailings are solid waste generated after the mining of iron mines, which have caused serious damage to the surrounding ecology and environment and have attracted widespread attention. By analyzing the formation causes, main components, and environmental effect mechanisms of iron tailings, the article systematically elaborates on the degree and mechanism of the harm of iron tailings to water bodies, atmosphere, soil, and ecosystems, and evaluates its impact on human health and sustainable development of society. On this basis, specific prevention and control measures have been proposed to reduce iron tailings emissions, realize resource recycling, and restore ecosystems. Research shows that iron tailings containing heavy metals can widely pollute the environment through dissolution and migration, and have significant biological toxicity effects. The research results can provide a theoretical reference for decision-making departments to formulate scientific and reasonable iron tailings disposal and ecological protection policies. It is recommended to strengthen specific research on the infiltration of toxic and harmful components in tailings in the future, and develop efficient and stable solidification technology, and vegetation-microbial joint restoration models to further reduce the ecological and environmental risks of iron tailings.

Assessment of extreme events and climate change on reservoir inflow is important for water and power stressed countries. Projected climate is subject to uncertainties related to climate change scenarios and Global Circulation Models (GCMs’). Extreme climatic events will increase with the rise in temperature as mentioned in the AR5 of the IPCC. This paper discusses the consequences of climate change that include extreme events on discharge. Historical climatic and gauging data were collected from different stations within a watershed. The observed flow data was used for calibration and validation of SWAT model. Downscaling was performed on future GCMs’ temperature and precipitation data, and plausible extreme events were generated. Corrected climatic data was applied to project the influence of climate change. Results showed a large uncertainty in discharge using different GCMs’ and different emissions scenarios. The annual tendency of the GCMs’ is bi-vocal: six GCMs’ projected a rise in annual flow, while one GCM projected a decrease in flow. The change in average seasonal flow is more as compared to annual variations. Changes in winter and spring discharge are mostly positive, even with the decrease in precipitation. The changes in flows are generally negative for summer and autumn due to early snowmelt from an increase in temperature. The change in average seasonal flows under RCPs’ 4.5 and 8.5 are projected to vary from -29.1 to 130.7% and -49.4 to 171%, respectively. In the medium range (RCP 4.5) impact scenario, the uncertainty range of average runoff is relatively low. While in the high range (RCP 8.5) impact scenario, this range is significantly larger. RCP 8.5 covered a wide range of uncertainties, while RCP 4.5 covered a short range of possibilities. These outcomes suggest that it is important to consider the influence of climate change on water resources to frame appropriate guidelines for planning and management.

Over the past decade, the volume and quality of data in the oil and gas industry have exploded, breeding exciting opportunities to implement machine learning for better data- driven decisions. One critical example is hydraulic fracturing (HF), given our ever-growing reliance on HF to meet global hydrocarbon demand. This paper systematically explores the work of several researchers to apply ML techniques (including linear regression, neural networks, support vector machine, decision trees, and more) to HF-related operations, from production forecast to HF design. Furthermore, this study examines how optimization algorithms (including gradient-free, differential evolution, and surrogate-based optimizations) are incorporated with different ML techniques for selecting optimal HF parameters (like fracture number, proppant concentration, and more) during the planning process. The paper aims to provide a comprehensive overview without delving too deeply into technical intricacies to ensure accessibility for a broader audience. Additionally, it introduces innovative techniques currently being integrated into the industry and offers a clear understanding of the processes involved. Ultimately, the analysis concludes that machine learning is an accurate and cost-effective alternative for hydraulic fracturing optimization.

A multiscale model that enables quantitative understanding and prediction of the size effect on scattering properties of micro- and nanostructures is crucial for the design of LED surface textures optimized for high light extraction efficiency (LEE). In this paper, a hybrid process for combining full-wave finite-difference time-domain simulation and a ray-tracing technique based on a bidirectional scattering distribution function model is proposed. We apply this method to study the influence of different pattern sizes of a patterned sapphire substrate on GaN-based LED light extraction from the microscale to the nanoscale. The results show that near-wavelength–scaled patterns with strong diffraction are not expected to enhance LEE. By contrast, microscaled patterns with optical diffusion behavior have the highest LEE at a specific aspect ratio, and subwavelength-scaled patterns that have antireflection properties show marked enhancement of LEE for a wide range of aspect ratios.

X-ray Fluorescence Computed Tomography (XFCT) is an emerging non-invasive imaging technique providing molecular-level data, gaining attention for high-resolution imaging. However, increased sensitivity with benchtop X-ray sources raises radiation exposure. Artificial Intelligence (AI), particularly deep learning (DL), has revolutionized medical imaging by delivering high-quality images in the presence of noise. In XFCT, traditional methods rely on complex algorithms for noise reduction, but AI holds promise in addressing high-dose concerns. We present an optimized SCUNet model for noise reduction in low-concentration XRF images. Compared to higher-dose images, our method’s effectiveness is evaluated. While various denoising techniques exist for X-ray and CT, few address to XFCT. The DL model is trained and assessed using the augmented data, focusing on background noise reduction. Image quality is measured using PSNR and SSIM, comparing outcomes with 100% X-ray dose images. Results show the proposed algorithm achieves high-quality images from low-dose and low-contrast agents, with a maximum PSNR of 39.05 and SSIM of 0.86. The model outperforms BM3D, NLM, DnCNN, and SCUNet in both visual inspection and quantitative analysis, particularly in high-noise scenarios. This indicates the potential of AI, specifically the SCUNet model, in significantly improving XFCT imaging by mitigating the trade-off between sensitivity and radiation exposure.

The effect of H2S with high concentrations on catalytic dry reforming of methane (DRM) process has seldom been focused on previously. Herein, a thermodynamic analysis of the DRM reactions in the presence of H2S with the concentration varying in 0-20 vol% was conducted firstly. Several typical types of catalysts including MgO, NiO/MgO and LaNiO3 in different states were prepared for executing DRM at 800 C, 0.1 MPa in the feed of 20 vol% CO2 and 20 vol% CH4 balanced with N2. The catalytic performance of each catalyst for DRM process under conditions of absence and presence of H2S was compared. A promotion effect of increasing H2S concentration on both the conversions of CO2 and CH4 and the molar yields of CO and H2 was observed on all the catalysts especially the MgO and the pristine NiO/MgO. While a significant decline in catalytic activity of either the reduced NiO/MgO or the reduced LaNiO3 catalyst after adding H2S, moderate reactant conversions still sustained. The results of process analysis and catalyst structure characterization suggest that H2S participation can contribute to the increment in CO2 and CH4 conversion, and active S-adsorbed species may play the key role of catalysis in the reactions involving H2S.

To achieve n-type doping in diamond, extensive investigations employing first principles have been conducted on various models of phosphorus doping and boron-phosphorus co-doping. The primary focus of this study is to comprehensively analyze the formation energy, band structure, density of states, and ionization energy of these structures. It is observed that within a diamond structure solely composed of phosphorus atoms, the formation energy of an individual carbon atom is excessively high. However, the substitution of two carbon atoms leads to the conversion of diamond into a p-type semiconductor. Upon examining the P-B co-doping structure, it is revealed that the doped impurities exhibit a tendency to form more stable cluster configurations. As the separation between the freely doped atoms and the cluster impurity structure increases, the overall stability of the structure diminishes, consequently resulting in an elevation of the ionization energy. Analysis of the electronic density of states demonstrates that the electron orbit of the B atom makes negligible contributions to the impurity levels during P-B doping.

With the ongoing amendment of the EU legislation on the treatment of urban wastewater, stricter requirements for the removal of pollutants are expected, which calls for the need for innovative wastewater treatment technologies. Biological systems are still the first choice. The survey of typical bioreactors applied in wastewater treatment is presented. Wastewater treatment objective, bio-chemical environment and microbial growth are selected as a main criterion for classification of these bioreactors. Hydraulic and kinetic aspects are considered, advantages and drawbacks of these bioreactors regarding the selection of appropriate type of the reactor as well as regarding operation of reactors are mentioned. The aim of this paper is to provide operators and designers with a brief overview of selected traditional and advanced processes, reactors, and technologies for nutrient removal from municipal wastewater. Another goal is to discuss the possibilities and limitations to comply with more strict effluent standards. From the evaluation of the published papers, it follows that the currently applied traditional methods of nutrients removal have the potential to convey also with the expected stricter limits.

Lactoperoxidase (LP) is an important enzyme of the salivary and mammary glands. It has been proven to increase the shelf life of raw milk by inhibiting the growth of bacteria, especially Listeria monocytogenes, Escherichia coli, Staphylococcus aureus, and Pseudomonas spp. The aim of this work was to verify the use of LP to extend the shelf life of meat products. In vitro experiments showed inhibitory effects against selected bacteria (Listeria innocua (ATCC 33090), Staphylococcus saprophyticus (CP054440.1), and Pseudomonas fluorescens (ATCC 13525) due to prolongation of the lag phase of growth curves. A lower increase in viable counts (P &lt; 0.05) was also found by testing the pork cubes surface treated with LP solution (5%) + L. innocua and stored for 7 days at 15 °C. LP has also been studied at concentrations of 0.25 and 0.50% in meat products (pork ham and pâté) during refrigerated storage (4 °C for 28 days). Lower viable counts were observed throughout the storage experiment, especially for 0.50% LP (P &lt; 0.05). Meat products containing LP also showed lower levels of oxidation (MAD) (P &lt; 0.05). According to these results, LP could extend the shelf life of a wider range of products.

The accompanying mechanical behavior during the flow of ore-rock dispersion is an important factor leading to the instability and failure of the orepass in the ore storage section. It is of great significance to accurately understand the instability characteristics of the well wall in the ore section, during the ore drawing process by understanding the flow characteristics and internal mechanical transfer mechanism of ore-rock dispersion. Using the discrete element method to analyze the flow characteristics, contact compactness, stress distribution characteristics and contact force probability distribution of the ore-rock dispersion, it realizes the quantitative characterization of the damage degree of ore-rock flow, and reveals the damage mechanism of mine storage wall. The results show that: (1) The friction between ore-rock particles, between ore-rock and well wall is an important reason for the change of the macroscopic flow form of ore-rock from “one” to “V” type. (2) The compactness and stress concentration of ores are increasing with the increase of storage depth, which is shown that with the increase of storage depth, the greater the probability of well wall instability. (3) The probability distribution of contact force strength between particles decreases exponentially in the whole process of ore drawing, in which the strong chain plays a major role in the stability of the dispersion system. (4) The number of overpressure and the overpressure coefficient can be used to quantitatively characterize the wall damage degree under the action of ore-rock flow. The dynamic side pressure decreases periodically in the form of exponential fluctuations, and the dynamic load formed by the ore-rock flow mainly played a role in the lower area of the ore storage section.

Developing and utilising of underground space is an vital direction for urban growth. Underground commercial streets, as a significant component of underground space accommodating extensive human social activities, and consequently necessitate the creation of human-scale spaces. In the evolution of urban design development towards greater refinement, applying architectural theories and excessively subjective designs has resulted in a deficiency of human-centered design and a disordered spatial environment. This study merges environmental psychology and architectural theory to determine the appropriate length of spatial scale. Two experiments focusing on spatial perception evaluation were conducted using a virtual experimental platform that featured varying dimensions of spatial scale combinations. These quantified combinations were correlated with perception evaluation, and regression analysis was employed to identify appropriate scale ranges, which were superimposed on the range of length selection. Finally, the optimal length and scale combination for underground commercial street spaces were established, providing a reference for the human-centered design of these environments.

Maize is an important staple food crop in sub-Saharan Africa (SSA). However, the average grain yield on farmers’ fields falls considerably short of the demand of the region’s population. In addition, the normal endosperm maize widely consumed in SSA is deficient in vitamin A. Drought, a consequence of climate change, is a major constraint to maize production, resulting in seasonal low grain yield in farmers’ fields. The objectives of this study were to assess the performance of newly developed extra-early maturing provitamin A hybrids under managed drought and well-watered conditions, compare the outcomes of multiple trait base-index and multi-trait genotype-ideotype distance index selection procedures, and identify drought-tolerant hybrids with stable performance across contrasting environments for commercialization in SSA. One hundred and ninety provitamin A hybrids and six checks were evaluated under managed drought and well-watered conditions at Ikenne for two seasons between 2021 and 2023. A 14*14-lattice design was used for the field evaluations under both research conditions. Drought stress was achieved by the complete withdrawal of irrigation water 25 days after planting. Results revealed significant differences among the hybrids under drought and well-watered conditions. Grain yield, ears per plant, and plant aspect under managed drought were correlated to the same traits under well-watered conditions suggesting that the expression of these traits is governed by common genetic factors. Twenty-nine hybrids were identified as top-performing drought-tolerant hybrids by the multiple trait base index and multiple-trait genotype–ideotype distance index. Of the selected outstanding 29 hybrids, 34% were derived from crosses involving the tester TZEEIOR 197, demonstrating the outstanding genetic potential of this inbred line. Further analysis of the 29 selected hybrids revealed TZEEIOR 509 × TZEEIOR 197 as the hybrid that combined the most drought-tolerant adaptive traits. However, the hybrids TZEEIOR 526 × TZEEIOR 97, TZEEIOR 384 × TZEEIOR 30, TZEEIOR 515 × TZEEIOR 249, TZEEIOR 510 × TZEEIOR 197, TZEEIOR 479 × TZEEIOR 197, and TZEEIOR 458 × TZEEIOR 197 were identified as the most stable hybrids across drought and well-watered conditions. These hybrids should be extensively tested in multi-location trials for deployment and commercialization in SSA.

The radio spectrum is a scarce and extremely valuable resource that demands careful real-time monitoring and dynamic resource allocation. Dynamic spectrum access (DSA) is a new paradigm for managing the radio spectrum, which requires AI/ML driven algorithms for optimum performance under rapidly changing channel conditions and possible cyber-attacks in the electromagnetic domain. Fast sensing across multiple directions using array processors, with subsequent AI/ML based algorithms for sensing and perception of the waveforms that are measured from the environment is critical for providing decision support in DSA. As part of directional and wideband spectrum perception, the ability to finely channelize wideband inputs using efficient Fourier analysis is much needed. However, a fine-grain fast Fourier transform (FFT) across a large number of directions is computationally intensive and leads to high chip area and power consumption. We address this issue by exploiting recently proposed approximate discrete Fourier transforms (ADFT) which has its own sparse factorization for real-time implementation at low complexity and power consumption. The ADFT is used to create a wideband multi-beam RF digital beamformer and temporal spectrum-based attention unit which monitors 32~discrete directions across 32~sub-bands in real-time using a multiplierless algorithm having low computational complexity. The output of this spectral attention unit is applied as a decision variable to an intelligent receiver that adapts its center frequency and frequency resolution via FFT channelizers that are custom-built for real-time monitoring at high resolution. This two-step process allows the fine-gain FFT to be applied only to directions and bands of interest as determined by the ADFT based low-complexity 2D spacetime attention unit. The fine-grain FFT provides a spectral signature that can find future use cases in neural network engines for achieving modulation recognition, IoT device identification, and RFI identification. Beamforming and spectral channelization algorithms, digital computer architecture, and early prototypes using a 32-element fully digital multichannel receiver and field programmable gate array (FPGA)-based high-speed software defined radio (SDR) is provided.

Given the many approaches to and definitions of gender responsive monitoring and evaluation (M&E) for health programs and interventions there is a lack of clarity on how to operationalize it including what to measure and how to measure it. We conducted a scoping review to understand what makes M&E gender responsive. We included 31 studies and conducted two rounds of extraction to delineate ways in which gender was integrated into M&E. Twelve articles described the use of theory to guide M&E though most were not related to gender. Twelve articles employed a gender score in data collection, most of which measured Likert scale responses related to gender equity. Even though most studies did not use a specific gender framework, most incorporated gender domains in their analysis. Seven studies used participatory methods in the design and implementation of M&E. Most studies conducted M&E on programs or interventions that were designed to be gender intentional and related to gender issues. Gender responsive M&E intentionally integrates gender into the M&E process, regardless of how gender-intentional the program or intervention is. Gender dimensions can be identified through gender theories, models, scores, and frameworks to inform tool development, data collection, analysis, and stakeholder engagement processes.

In the process of sewage coagulation treatment, quartz sand is often used as a heavy medium to accelerate the settling rate of flocs, but it will adversely affect the removal efficiency of pollutants. The factors that affect the coagulation effect and can be controlled manually include the quartz sand dosage, coagulant dosage, sewage pH, stirring time, settling time, etc, their reasonable setting is critical to. This paper was to study the optimal conditions of quartz sand enhanced coagulation(QSEC), first, single-factor tests were conducted to preliminarily explore the optimal range of influencing factors, and then response surface methodology（RSM）tests were performed to accurately determine the optimums of significant factors. The results showed that the addition of quartz sand can’t improve the water quality of coagulation treatment, but it can significantly accelerate the coagulation settlement process, the quartz sand dosage, the coagulant dosage and sewage pH all impacted significantly on its coagulation effect, and existed inflection points. A model that could guide QSEC was obtained by RSM tests. The model optimization and experimental validation showed that the optimal QSEC conditions for treating domestic sewage were as follows: the polyaluminum chloride(PAC) dosage, cationic polyacrylamide(CPAM) dosage, the sewage pH, quartz sand dosage, stirring time and settling time were 0.97 g·L-1, 2.25 mg·L-1, 7.22, 2 g·L-1, 5 minutes and 30 minutes, respectively, and the turbidity of treated sewage was reduced to 1.15 NTU.

To secure logic circuits against the illegal copying the insertion of the so-called key bit inputs using XOR/XNOR gates has been proposed in . The inserted gates modify (lock) the behavior of the original circuit and only the correct choice of the secret key bits guarantees the equivalent behaviour of the locked circuit to the original circuit. To break this kind of security, i.e. to find the secret key bits, there was a SAT solver based attack proposed in . The aim of this work is to experimentally verify this attack on several locked circuits with various number of primary inputs and outputs and with various number of gates. Except for the random placement of the key gates we evaluate also the positioning with chaining elimination. The obtained and presented results show that we were able to unlock 10 of 11 circuits within few minutes on a common PC.