This paper presents a design and performance analysis of a 10-element 5G massive MIMO antenna array for sub-6GHz mobile handsets, specifically for LTE bands 42 (3400-3600 MHz), 43 (3600-3800 MHz), 48/49 (3550-3700 MHz) applications. The proposed antenna array consists of 10 closely spaced linearly polarized inverted-F antennas with a compact size of 20 × 9 mm2 of a single element. The proposed antenna array provides high gain, high efficiency, and low correlation between the antenna elements, which results in improved channel capacity, increased data rate, and enhanced signal quality. The performance of the antenna array is evaluated in terms of the radiation pattern, gain, efficiency, and correlation coefficient. The simulation and measured results show that the proposed antenna array achieves an approximate peak gain of 3.1 dBi at the resonance frequency, a total efficiency of 65 %, and a low correlation coefficient of 0.06 between the antenna elements. Therefore, the proposed 5G massive MIMO antenna array is a promising candidate for sub-6 GHz mobile handsets, particularly for LTE bands 42/43/48/49 applications.

Prokaryotic genomes are dynamic tapestries that are strongly influenced by mobile genetic elements (MGEs), including transposons (Tn’s), plasmids, and bacteriophages. Of these, miniature inverted-repeat transposable elements (MITEs) are undoubtedly the least studied MGEs in bacteria and archaea. This review explores the diversity and distribution of MITEs in prokaryotes and describes what is known about their functional roles in the host and involvement in genomic plasticity and evolution.

In this paper, we identify issues and possible solutions in the key area of large-scale antenna systems, also know as Massive Multiple Input Multiple Output (MIMO) systems. Additionally, we propose the use of Massive MIMO technology as a means to tackle the uplink mixed-service communication problem. Under the assumption of an available physical narrowband shared channel (PNSCH), the capacity of the MTC network and, in turn, that of the whole system, can be increased by grouping Machine-Type Communication (MTC) devices into clusters and letting each cluster share the same time-frequency physical resource blocks. We study the feasibility of applying sub-optimal linear detection to the problem of detecting a large number of MTC devices sharing the same time-frequency resources at the uplink of a base station (BS) equipped with a large number of antennas, M. In our study, we derive the achievable lower-bound rates for the studied sub-optimal linear detectors and show that the transmitted power of each MTC device can be reduced as M increases, which is a very important result for powerconstrained MTC devices running on batteries. Our simulation results suggest that, as M is made progressively larger, the performance of sub-optimal linear detection methods approach the matched filter bound, also known as perfect interference-cancellation bound.

Extensive research has been conducted on printable antenna technologies, believed to be fast-growing due to their significant impact on wireless devices. It is necessary to study the progress of printable antenna technology as they are core devices for wireless technology today. This review work offers a comprehensive account of the previous and recent research achievements based on the principle of printable antenna, and parametric studies of several key design parameters, for future wireless network applications. The systems considered for evaluation include broadband techniques, large Bandwidth, high gain, dual/multi-band, or reconfigurable structure, low-profile, size-reduction, compact, linear, or circular polarization applications. It also highlights the fabrication procedures, and the numerous material characteristics affecting the antenna performance for various wireless applications with design considerations. Fully printed antennas on different substrates and conductive ink were investigated, including polyethylene terephthalate (PET), synthetic paper (Teslin), resin-coated photo paper, and Kapton polyimide substrates, among many others. The findings show that the fully inkjet-printed antenna made fabrication easy, improving the accuracy and conductivity of the printed patterns by concentrating on the inherently difficult problems and opportunities. Inkjet-printed antennas are believed to be the futuristic demand for sustainability and wireless solution in several ways.

Examining contemporary developments and cutting-edge approaches in the field, this literature review explores how antenna design for transmission lines is changing. Review findings are compiled from a variety of academic sources, including pertinent technical reports published as recently as 2018, conference papers, journal articles, and reports. A variety of antenna topologies suited for transmission lines are evaluated in this paper, including microstrip, slot, and patch antennas, with a focus on theoretical frameworks and practical implementations. This overview clarifies the complex relationship between antenna design and transmission line characteristics by looking at important factors like impedance matching, bandwidth, and radiation pattern management. Notable developments in materials, fabrication methods, and numerical simulations are also examined and their effects on antenna performance explained. Through a comprehensive analysis of the literature, this review offers valuable insights into the state-of-the-art antenna design practices for transmission lines, facilitating informed decision-making and inspiring future research endeavors in this field.

A high-gain broadband circularly polarized crossed dipole antenna is designed. This antenna utilizes two pairs of cross dipoles and a pair of phase delay lines to form circularly polarized radiation. Open-circuit stubs are loaded on the four arms of these two pairs of cross dipoles to introduce new circularly polarized resonating frequency. A rectangular ring patch is introduced directly below the cross dipoles to form the third circularly polarized resonating frequency, thereby broadening the axial ratio bandwidth of the antenna. In addition, metal posts are loaded at the four right angles of the rectangular ring patch to increase the antenna gain. Measurement results show that the antenna achieves a 3dB axial ratio bandwidth of 29.2% (1.9 GHz-2.55 GHz) and maintains a gain of 7.5 dB within the passband, exhibiting good circularly polarized radiation performance.

Dipole antennas, fundamental components in wireless communication systems, have garnered significant attention due to their versatility and efficiency across various applications. This literature review explores the performance analysis of dipole antennas, focusing on recent advancements and methodologies from 2019 to 2024. Employing a systematic approach, the review synthesizes findings from multiple databases, emphasizing peer-reviewed studies that delve into dipole antenna designs and applications. Through meticulous data extraction, key parameters influencing dipole antenna performance, such as material properties and operating frequency, are identified and analyzed. Results highlight the widespread utilization of dipole antennas in wireless communication systems, including indoor positioning, mobile communication, and antenna calibration, among others. Discussions underscore the evolution of dipole antennas in base station environments and their role in filtering applications. The review concludes by emphasizing the continued relevance and evolution of dipole antennas, showcasing their adaptability and potential across diverse wireless communication contexts.

A configurable design of a microstrip square spiral RFID tag antenna, for a wide range of microwave frequencies in S- and C-band, is presented. The design is parameterized in dimensions, and hence changing the design frequency (or frequencies) is easy, by changing only an initial value for the spiral geometry. A tag specimen was fabricated using Cu electroplating technique according to the design for frequencies of interest in the areas of 2.4 and 5.8 GHz. The substrate material is a 320 μm high resistivity Si and the bridge dielectric is a 15μm polyimide PI2525. The microfabrication process involves steps of metallic structure pattern transfer techniques with optical UV lithography procedures. The reflection coefficient and gain of the specimen were measured inside an anechoic enclosure using a vector network analyzer (VNA) and a TEM horn test antenna over a frequency range of up to 6 GHz. Simulated and measured results are presented and discussed, exhibiting reasonable agreement.

This paper presents a concise mathematical framework for investigating both feed-forward and backward process, during the training to learn model weights, of an artificial neural network (ANN). Inspired from the idea of the two-step rule for backpropagation, we define a notion of F_adjoint which is aimed at a better description of the backpropagation algorithm. In particular, by introducing the notions of F-propagation and F-adjoint through a deep neural network architecture, the backpropagation associated to a cost/loss function is proven to be completely characterized by the F-adjoint of the corresponding F-propagation relatively to the partial derivative, with respect to the inputs, of the cost function.

This paper presents a wideband dual-polarized dipole antenna structure operating at 1.7-3.8 GHz (76.4%). For a traditional 4G dipole antenna which covers the band 1.71 GHz- 2.69 GHz, it’s difficult to maintain the satisfactory impedance matching and normal stable radiation patterns within the 5G sub-6 GHz band 3.3-3.8 GHz, which mainly due to the fixed antenna height is no longer a quarter-wavelength. To solve this, a connected-ring-shaped metasurface structure is proposed and deployed to operate as an artificial magnetic conductor (AMC). As a result, stable antenna radiation patterns are obtained within the whole band 1.7-3.8 GHz. For verification, this wideband dipole antenna using AMC is implemented and tested. The measured results show that the proposed antenna has an impedance bandwidth of 80.7% (1.7-4.0 GHz). It has an average measured in-band realized gain of 7.0±1.0 dBi and a stable 70∘±5∘ half power beam width (HPBW) within the 4G/5G-sub 6GHz bands 1710-2690 MHz and 3300-3800 MHz.

Due to the optical properties of the Electron Transport Layer (ETL) and Hole Transport Layer (HTL), inverted perovskite solar cells can perform better than traditional perovskite solar cells. It is essential to compare both types to understand their efficiencies. In this article, we studied inverted perovskite solar cells with NiOx/CH3NH3Pb3/ETL (ETL = MoO3, TiO2, ZnO) structures. Our results showed that the optimal thickness of NiOx is 80 nm for all structures. The optimal perovskite thickness is 600 nm for solar cells with ZnO and MoO3, and 800 nm for those with TiO2. For the ETLs, the best thicknesses are 100 nm for ZnO, 80 nm for MoO3, and 60 nm for TiO2. We found that the efficiencies of inverted perovskite solar cells with ZnO, MoO3, and TiO2 as ETLs, and with optimal layer thicknesses, are 30.16%, 18.69%, and 35.21%, respectively. These efficiencies are 1.5%, 5.7%, and 1.5% higher than those of traditional perovskite solar cells. Our study highlights the potential of optimizing layer thicknesses in inverted perovskite solar cells to achieve higher efficiencies than traditional structures.

For their speed in data processing, low heights and cheapness, patch antennas are important to 5G networks. While there have been improvements in the area of bandwidth and size reduction; however, there are still problems that need to be fixed with regards achieving high data rates as well as wideband operation and compact sizes for 5G applications. In the coming years researchers should concentrate on materials optimization and feeding methods so that they can work efficiently at shorter wavelengths for next-generation systems while still covering all necessary bands.

Focused microwave breast hyperthermia (FMBH) employs a phased antenna array to perform beamforming that can focus microwave energy at targeted breast tumors. Selective heating of the tumor endows the hyperthermia treatment with high accuracy and low side effects. The effect of FMBH is highly dependent on the applied phased antenna array. This work investigates the effect of polarizations of antenna elements on the microwave focusing results by simulations. We explore two kinds of antenna arrays with the same number of elements using different digital realistic human breast phantoms. The first array has all the elements’ polarization in the vertical plane of the breast while the second array has half elements’ polarization in the vertical plane and the other half in the transverse plane, i.e., cross polarization. In total 96 sets of different simulations are performed, and the results show that the second array leads to a better focusing effect in dense breasts than the first array. This work is very meaningful for the potential improvement of the antenna array for FMBH, which is of great significance for the future clinical applications of FMBH. The antenna array with cross polarization can also be applied in micro-wave imaging and sensing for biomedical applications.

This paper presents a compact wideband circularly polarized cross dipole antenna with low-pass filter response. It consists of two pairs of folded crossed dipole arms printed separately on both sides of the top substrate, and the two dipole arms on the same surface are connected by an annular phase-shifting delay line to generate circular polarization. A bent metal square ring and four small metal square rings around the cross dipoles are employed to introduce new resonant frequencies, effectively extending the impedance and axial ratio bandwidth. Four square patches printed on the middle substrate are connected to the ground plane by the vertical metal plates, in order to reduce the antenna height. Thus, a compact wideband circularly polarized antenna is realized. In addition, a transmission zero can be introduced at the upper frequency stopband by the bent metal square rings, without using extra filter circuits. For verification, the proposed model is implemented and tested. The overall size of the model is 90mm×90mm×33mm(0.37λ0×0.37λ0×0.14λ0, λ0 denotes the center operating frequency). The measured impedance bandwidth and 3 dB axial ratio bandwidth are 53.3% and 41%, respectively. More than 15 dB upper-band radiation suppression level is realized, indicating a good low-pass filter response.

It has been proven that in standard Einstein gravity, exotic matter (i.e. matter violating the point-wise and averaged weak and null energy conditions) is required to stabilize traversable wormholes. Quantum field theory permits these violations due to the quantum coherent effects found in any quantum field . Even reasonable classical scalar fields violate the energy conditions. In the case of the Casimir effect and squeezed vacuum states, these violations have been experimentally proven. It is advantageous to investigate methods of minimizing the use of exotic matter. One such area of interest is extended theories of Einstein gravity. It has been claimed that in some extended theories, stable traversable wormholes solutions can be found without the use of exotic matter. There are many extended theories of gravity and in this review paper we first explore f(R) theories and then explore some wormhole solutions in f(R) theories including Lovelock gravity.

With the rapid consumer adoption of mobile devices such as tablets and smart phones, the tele-traffic has experienced a tremendous growth, low power technologies are highly desirable for future communication networks. In this paper, we consider an ambient backscatter (AB) based user cooperation (UC) scheme for mmWave wireless powered communication networks (WPCN) with lens antenna arrays. Firstly, we formulate an optimization problem to maximize the minimum rate of two users by jointly designing power and time allocation. Then we introduce auxiliary variables and transform the original problem into a convex form. Finally, we propose an efficient algorithm to solve the transformed problem. Simulation results demonstrate that the proposed AB based UC scheme outperforms the competing schemes, thus improve the fairness performance of throughput in WPCN.

The prevalence of differential equations as a mathematical technique has refined the fields of control theory and constrained optimization due to the newfound ability to accurately model chaotic, unbalanced systems. However, in recent research, systems are increasingly more nonlinear and difficult to model using Differential Equations only. Thus, a newer technique is to use policy iteration and Reinforcement Learning, techniques that center around an action and reward sequence for a controller. Reinforcement Learning (RL) can be applied to control theory problems since a system can robustly apply RL in a dynamic environment such as the cartpole system (an inverted pendulum). This solution successfully avoids use of PID or other dynamics optimization systems, in favor of a more robust, reward-based control mechanism. This paper applies RL and Q-Learning to the classic cartpole problem, while also discussing the mathematical background and differential equations which are used to model the aforementioned system.

This paper presents a new approach to suppress interference between neighbouring radiating elements resulting from surface wave currents. The proposed technique will enable the realization of low-profile implementation of highly dense antenna configuration necessary in SAR and MIMO communication systems. Unlike other conventional techniques of mutual coupling suppression where decoupling slab is located between the radiating antennas the proposed technique is simpler and only requires embedding linear slots near the periphery of the patch. Attributes of this technique are (i) significant improvement in the maximum isolation between the adjacent antennas by 26.7 dB in X-band, & >15 dB in Ku and K-bands; (ii) reduction in edge-to-edge gap between antennas to 10 mm (0.37λ); and (iii) improvement in gain by >40% over certain angular directions, which varies between 4.5 dBi to 8.2 dBi. The proposed technique is simple to implement at low-cost.

Emerging data processing techniques brought back into attention the HF range communication as an interesting alternative to third-party solutions for IoT applications, such as data transmission in distributed energy production facilities. The physical size of HF antennas, often comparable to the surrounding objects, require in-situ radiation measurements. Drone-borne measuring systems are already known as a flexible solution, but mostly restricted to higher frequency ranges. In this work, we propose to use an electrically small, folded dipole as a probe for drone-borne measurements on HF antennas. We also propose a calibration approach for the effects related to the near-field zone, and to the drone body proximity. The impact of ground reflection is also investigated. We show that despite its low, realized gain figure such a probe can provide stable results for near-field measurements, even at low input power levels.

The need for integrated high-frequency systems has increased significantly, leading to the development of efficient antennas operating in the 0.1-10 terahertz (THz) range. Using graphene as the conducting 2D material and hexagonal boron nitride (hBN) as the dielectric substrate, this research effort examines the design and performance evaluation of a THz band antenna functioning on supporting nanotechnology. The researchers contrasted the system’s performance with the 6G wireless network requirements after analyzing the antenna performance, radiation patterns, and impedance matching. According to this research, graphene, along with hBN can enhance antenna performance overall in the THz band and open pathways for advanced communication. The application of the designed antenna in a 6G wireless network will be tested through um MIMO configuration to achieve a higher data rate.

We are presenting a new method for the treatment of large macular holes (MH) with the use of an inverted flap consisting of both internal limiting membrane (ILM) and epiretinal proliferation (EP). A prospective interventional case series was conducted from September 2021 to January 2023. MH patients with coexistent EP visualized preoperatively in macula optical coherence tomography and MH minimum linear diameter larger than 400 microns underwent standard pars plana vitrectomy with the creation of an inverted petaloid flap (consisting of both ILM and EP) and gas tamponade. 16 eyes were included in our study. MH closure was successful in all the eyes with a single procedure. Preoperative minimum linear diameter was 707.63(±164.02μm) and preoperative best corrected visual acuity was 1.11±0.52. Postoperative BCVA was 0.51±0.20 (p=0.01) at 6weeks postoperatively and final BCVA was 0.45±0.20 (p=0.008). EP can be safely combined with ILM for the creation of an inverted, petaloid flap to cover and facilitate the closure of large MH.

A Partial discharge (PD) occurrence in high-voltage (HV) and medium-voltage (MV) power assets is a warning sign of insulation system degradation or defective manufacturing/assembly, that may cause catastrophic damage and eventually lead to the breakdown of the power equipment. Ultra-high frequency (UHF) PD measurement technology has extensively been used to monitor the insulation health of the HV or MV equipment due to its high immunity against ambient noise and conducted disturbances. This paper presents experimental validation of a new design of a UHF planar rectangular microstrip antenna that can be used for PD monitoring of HV and/or MV power equipment, such as power transformers. The designed planar rectangular microstrip antenna has a compact size of 80mmx70mmx1.6mm. Laboratory experiments were performed to validate the antenna sensitivity to PD activity caused by insulation defects created inside an oil-filled transformer tank model. PD measurement results confirm that the proposed rectangular microstrip antenna has high sensitivity and high signal-to-noise ratio (SNR), thanks to its capability to suppress external noise disturbances, especially during online PD monitoring. Thus, the proposed UHF antenna seems to be a promising and alternative PD sensor that can be employed in UHF PD monitoring systems of HV or MV power equipment.

This literature review offers a comprehensive analysis of antenna designs tailored for 6G applications and THz communications. Various antenna types, including elliptical lens, WHEMS, grid array, CP horn, Quasi Yagi-Uda, patch, transmit array, Vivaldi patch, SRR slotted waveguide array, RCA, and Cassegrain antennas, are scrutinized in terms of their dimensions, characteristics, frequency ranges, and materials. The study highlights existing works on antenna design for 6G applications, exploring different fabrication techniques like PCB technology, LCP technology, Topas fabrication, Wire-cutting EDM, 3D Printing, Laser-drilling processes, and CNC machining. Notably, PCB technology exhibited promise with antennas such as WHEMS, patch, and Vivaldi patch, achieving significant bandwidth and gain. However, gaps remain in research, urging further exploration into additional fabrication methods and antenna designs to meet the demands of 6G networks. The study underlines the need for advanced, intelligent antennas capable of higher bandwidth and better performance in view of future wireless communications technologies such as 6G.

Fractal array antennas are multiband arrays having ultra wide band and space filling facility. But Side lobe levels and large number of antenna elements are the major designing challenges of these arrays. In this paper, design and analysis of octagonal fractal array antenna is investigated with Morse-Thue fractal density tapering technique (MTFDT). Due to the proposed technique, a remarkable improvement has observed in Side lobe levels and thinning of the elements can also be attained at the various iterations of octagonal fractal array antenna. These arrays are analyzed and simulated by MATLAB-15 programming.

The growing use of drones in precision agriculture highlights the need for enhanced operational efficiency. Despite the ability of computer vision based on deep learning has made remarkable progress in the past ten years, when it comes to segmentation task on UAVs, there is always a conflict between the demand of high precision and low inference latency. Due to such a dilemma, we propose the IRB-YOLO, an efficiency model based on Inverted Residual Block, devoting to provide constructive strategies in real-time detection tasks of UAV camera. The working details of this paper are as follows: (1) This paper innovates with a IR-Block(Inverted Residual Block), integrated into a refined YOLOv8-seg structure to create IRB-YOLO. This model specializes in pixel-level classification of UAV-acquired RGB images, facilitating the creation of exact maps to guide agricultural strategies. (2)When it comes to the experiments on a Vatica dataset with any other light-weight segmentation model, IRB-YOLO achieve at least a 3.3% increase in mAP. Further validation using a diverse species dataset confirms its robust generalization. (3)Without overloading the complex attention mechanism and deeper and deeper network, a stem that incorporates efficient feature extraction components, inverted residual block, can still possess outstanding modeling capabilities. IRB-YOLO builds a bridge between academic research and edge deployment of drones, making it applicable in real-world scenarios.

Recently a measure termed F* was described, as an interpretable transformation of the F measure, also known as the Dice coefficient. Using elementary mathematical methods, it is shown that F* is in fact identical to a previously described measure, monotonically related to the F measure, and variously termed in previous publications, dating from the late 19^th to the late 20^th century, as the ratio of verification, the Jaccard similarity measure or index, the threat score, the Tanimoto index, and the critical success index. The origins of these different terms in different disciplines (weather forecasting, ecology, machine learning) may explain the repeated independent redescription of this measure.

This comprehensive article explores Massive MIMO (M-MIMO) design and its associated concepts, focusing on the seamless integration requirements for Beyond 5G (B5G) and 6G networks. Addressing critical aspects such as RF chain reduction, pilot contamination, Cell-Free MIMO, and security considerations, the article delves into the intricacies of M-MIMO in the evolving landscape of B5G. Moreover, the emerging MIMO concepts in this article include AI-enabled M-MIMO three-dimensional beamforming, reconfigurable intelligent surfaces, visible light communication, and THz spectrum utilization. This review highlights challenges and open research issues, including Narrow Aperture Antenna Nodes, Plasmonic Antenna Arrays, Integrated Sensing with M-MIMO, and the application of Federated Learning in M-MIMO systems. By examining these cutting-edge developments, the article aims to contribute to advancing knowledge in the field and inspire future research directions in the exciting realm of B5G and 6G networks.

The rock joint fissure slope in cold regions is prone to deformation and failure problems such as relaxation, tension and collapse under freeze-thaw (F-T) cycles. Based on the ideology of clean production and promoting the structural integrity of geotechnical projects in cold areas, this study designed and prepared aeolian-sand (AS) to replace part of river sand as a filling mortar material by taking advantage of the low cost and easy availability of AS. Investigations were carried out to determine the impact of varying proportions of AS in mortar on the microstructure and shear properties of the mortar-rock interface under F-T cycles. Therefore, F-T cycle testing, nuclear magnetic resonance (NMR) testing and shear testing were carried out on grout with different proportions of AS. The results show that the right proportion of AS replacement could enhance the shear deformation resistance and F-T resistance of the mortar-rock interface, and 30% proportion is the optimal proportion. By increasing of F-T cycles, the three types of specimens showed different degrees of particle spalling, shedding and cracking. The slurry-rock interface layer in the A (0%) group exhibited the most severe F-T deterioration, while the B (15%) group showed a lesser degree, and the C (30%) group performed the best. T2 spectrum curve and total spectrum area change law from the microscopic point of view to verify the 30% AS proportion mortar-rock interface F-T resistance is the strongest, followed by 15% AS proportion mortar, the weakest is ordinary mortar. The degradation of the mortar-rock bond is primarily due to the conversion of solid to liquid phases and the movement of internal water caused by fluctuating temperatures. The extent of F-T deterioration in the slurry-rock interface layer is greatly affected by the varying proportions of AS. The shear strength and shear stiffness of specific proportion of AS decreased with the increase of F-T cycles. For same F-T cycles, the shear strength and shear stiffness of group C (30%) were the highest, followed by group B (15%) and group A (0%). The grout material not only reinforces the F-T joint fissure slope, but also reduces the cost of grout reinforcement and promotes the clean production of geotechnical structures.

In this letter, we propose a pattern-diversity antenna with different radiation patterns at two different frequency bands (f1 and f2) (f1: broadside radiation pattern, f2: conical radiation pattern). The proposed structure consists of a central circular antenna and two annular ring antennas; each of the three antennas has individual ports. Two of the ports exhibit orthogonal broadside radiation patterns; the other two ports exhibit orthogonal conical radiation patterns. Thus, they have polarization diversity characteristics. To improve isolation between ports, the inner part of the annular ring antennas is shorted via array, and the outermost port is positioned orthogonal to the other ports. Using this configuration, the isolation between ports was measured as -26.7 dB and -30.1 dB at the two frequency bands, respectively. Experimental results based on the fabricated prototype show that the proposed antenna achieves -10 dB bandwidths of 240 MHz (5.71~5.95 GHz) and 210 MHz (7.69~7.9 GHz) at f1 and f2, respectively.

The urban future looks unclear. Even if some suggest that the future of urbanism would be drawn according to the needs and impositions of artificial intelligence or ecological requirements it is still not enough light shed on integral human development. Therefore the paper examines the relation between sacrum elements of the metaphysical dimension of living and potential technological innovations that would occur shortly. Keeping in mind that technology alone is not sufficient to transfigure human life completely into novel forms of being, metaphysical arguments are in use to bring fourth new urban patterns into a discussion. The relation or rather superposition of sacrum and future technologies is introduced as a basis of inverted city phenomenon whereby implicit manner would be explained and described in an explicit language. The inverted city, based on the sacrum and future tech dimensions, would introduce a new lifestyle model that relies on the juxtaposition of wanderer life qualities along with best practices of sedentary life. The inverted city is a completely new phenomenon though it is inherited from the deep past in terms of the total heritage approach.

In this paper, modelling design and analysis of a triple inverted pendulum have been done using Matlab/Script toolbox. Since a triple inverted pendulum is highly nonlinear, strongly unstable without using feedback control system. In this paper an optimal control method means a linear quadratic regulator and pole placement controllers are used to stabilize the triple inverted pendulum upside. The impulse response simulation of the open loop system shows us that the pendulum is unstable. The comparison of the closed loop impulse response simulation of the pendulum with LQR and pole placement controllers results that both controllers have stabilized the system but the pendulum with LQR controllers have a high overshoot with long settling time than the pendulum with pole placement controller. Finally the comparison results prove that the pendulum with pole placement controller improve the stability of the system.

The new digital infrastructure has become an important basis for the green development of agriculture. This paper selects provincial sample data from 2006 to 2022, constructs an indicator system to measure new digital infrastructure and agricultural green total factor productivity, and explores how new digital infrastructure can promote agricultural green development. The results show that: (1) the new digital infrastructure has a significant role in promoting the green development of agriculture, and this conclusion is still valid after processing endogeneity and heteroscedasticity; (2) Technology and land factors play an intermediary role in the promotion of green agricultural development by the new digital infrastructure, that is, the new digital infrastructure helps to improve the quality and technical level of cultivated land and thus promote green agricultural development; (3) Labor force factors optimize the mediating role of technology factors, that is, the higher the quality of labor force, the stronger the role of the new digital infrastructure in promoting the green development of agriculture through the technological path; (4) The effect of new digital infrastructure on the green development of agriculture is obviously heterogeneous, and the effect is more obvious in northwest China and the regions with lower marketization level, higher environmental regulation level. This study is helpful to clarify the relationship between new digital infrastructure and agricultural green development in China, and provide corresponding policy suggestions for promoting regional agricultural green development.

A popular approach to learning about admixture from population genetic data is by computing the allele-sharing summary statistics known as f-statistics. Compared to some methods in population genetics, f-statistics are relatively simple, but interpreting them can still be complicated at times. In addition, f-statistics can be used to build admixture graphs (multi-population trees allowing for admixture events), which provide more explicit and thorough modeling capabilities but are correspondingly more complex to work with. Here, I discuss some of these issues to provide users of these tools with a basic guide for protocols and procedures. My focus is on the kinds of conclusions that can or cannot be drawn from the results of f₄-statistics and admixture graphs, illustrated with real-world examples involving human populations.

The efficiency of organic solar cells (OSCs) is influenced by various factors, among which environmental temperature plays a significant role. Previous studies have shown that the thermal stability of these cells can be enhanced by incorporating a third component into their structure. Ternary organic solar cells, in particular, have shown promising results in improving thermal stability. A well-designed electron transport layer (ETL) can significantly bolster thermal stability by facilitating efficient charge transport and reducing charge recombination. In this study, we investigated the effect of temperature on the efficiency of inverted ternary structures, ranging from 300 K to 400 K. The structures examined include FTO/SnO2/PM6:D18:L8-BO/PEDOT: PSS/Ag, FTO/Spiro-OMeTAD/PM6:D18:L8-BO/PEDOT: PSS/Ag, and FTO/PC60BM/PM6:D18:L8-BO/PEDOT: PSS/Ag. Through simulations employing three different electron transport layers—SnO2, Spiro-OMeTAD, and PC60BM—we observed that at 340 K (65°C) these structures maintained 92% of their original high efficiency of ~20% at 300 K, which represents a high level of thermal stability under the high PCE condition.

Background: The two-stage technique combining the Endoscopic Retrograde CholangioPancreatography (ERCP) with common bile duct (CBD) clearance carried out before the laparoscopic cholecystectomy represents the most common approach for CBD stones. Over time, different techniques have been proposed to manage cholecysto- choledocholithiasis (CCL) advantageously in one stage. Among these, the laparoendoscopic rendez-vous (LERV) addresses the CCL issue with a laparoscopic cholecystectomy with insertion of a guide wire performed at initial stage of the procedure, followed by the clearance of the bile duct carried out by the endoscopists. The goal of this study was to evaluate the efficacy and safeness of LERV procedure recording results and complications, also making a comparison between our results and current literature. Methods: We reviewed our experience of all consecutive patients with cholecysto-choledocholithiasis managed with LERV between January 2018 and December 2023. LERV success rate, operative time, length of hospital stay, stone recurrence, incidence of endoscopic and surgical complications were analysed. Results: A total of 120 patients underwent LERV in our facilities. We reported a 97% LERV success rate, 1.6% conversion-to-open rate, a median intraoperative time of 122 (range 95-220) min. The median hospital stay was 4 (range 2-38) days. An overall morbidity of 15% was reported (18/120): 15 Clavien-Dindo type 1/2, 2 type 3a and one type 3b. In two cases a re-operation during the hospital stay was necessary. At a median follow-up of 14 months (3-59) five patients experienced stone recurrence requiring redo-ERCP in two cases. Conclusion: LERV offers the significant advantage of a single stage procedure and hospitalisation along with a lower risk of post-ERCP pancreatitis, failed CBD cannulation and complications. Our experience confirms safety and effectiveness of the technique for CCL management.

This paper deals with miniaturization technique based on frequency reduction using top loaded dielectric discs. In contrast to a simple monopole, the resonant frequency of monopole loaded with two dielectric discs changes from 1.98 to 1.29 GHz, resulting 34.84% reduction in resonant frequency keeping the antenna length (36.00 mm) unaltered. It is well-known fact that dielectric material can trap the energy to be delivered from source to antenna and as a result, it is unable to radiate efficiently. Then any approach to use the dielectric material for miniaturization process must, therefore, antenna coupled in such a way that it can radiate efficiently. The dielectric disc on top of monopole creates an inductive situation in a similar way to oppositely directed wire loop compensate the capacitive effect present at monopole causes the reduction in resonant frequency. This concept is implemented without sacrificing any desired features like bandwidth, radiation characteristics and efficiency (more than 98%) and analyzed with an equivalent circuit model. Experimental results illustrate good agreement with simulation results. This monopole antenna in car can be designed for GPS system, car to car communication, GSM or CDMA operation.

The aims of this study are to measure the technical efficiency (TE) of Cambodian household’s rice production and trying to determine its main influencing factors using the stochastic frontier production function. The study utilized primary data collected from 301 rice farmers in three selected districts of Battambang by structured questionnaires. The empirical results indicated the level of household rice output varied according to differences in the efficiency of production processes. The mean TE is 0.34 which means that famers produce 34% of rice at best practice at the current level of production inputs and technology, indicates that rice output has the potential of being increased further by 66% at the same level of inputs if farmers had been technically efficient. Furthermore, between 2013-2015 TE of household’s rice production recorded -14.3% decline rate due to highly affected of drought during dry season of 2015. Moreover, evidence reveals that land, fertilizer, and pesticide are the major influencing input factors of household’s rice production, while disaster, education of household head, family size and other crops’ cultivated area are core influencing factors decreasing TE. Conversely, the main influencing factors increasing TE are irrigated area, number of plot area and sex of household head.

The aims of this study are to measure the technical efficiency (TE) of Cambodian household’s rice production and trying to determine its main influencing factors using the stochastic frontier production function. The study utilized primary data collected from 301 rice farmers in three selected districts of Battambang by structured questionnaires. The empirical results indicated the level of household rice output varied according to differences in the efficiency of the production processes. The mean TE is 0.34 which means that famers produce 34% of rice at best practice at the current level of production inputs and technology, indicates that rice output has the potential of being increased further by 66% at the same level of inputs if farmers had been technically efficient. Furthermore, between 2013-2015, TE of household’s rice production recorded -14.3% decline rate due to highly affected of drought during dry season of 2015. Moreover, evidence reveals that land, fertilizer, and pesticide are the major influencing input factors of household’s rice production, while disaster, education of household head, family size and other crops’ cultivated area are core influencing factors decreasing TE. Conversely, the main influencing factors increasing TE are irrigated area, number of plot area and sex of household head.

The present study aims to measure the technical efficiency and establish core factors effecting rice production in Cambodia. Four-years dataset generated from the central government document “Profile on Economics and Social” of entire 25 provinces between 2012-2015 and the stochastic production frontier model (SFA) was applied. The results indicated that the level of output (quantity) of Cambodian rice production varied according to the different level of capital investment in agricultural machineries, total rice actual harvested area, and technically fertilizers application within provinces. Furthermore, evidence revealed the overall mean efficiency of rice production is 78.4% implies that there is still room to further improve technical efficiency by given the same level of inputs and technology. More importantly, the findings revealed that irrigation, production technique and amount of agricultural supporting staffs are being as the most important influencing factors of rice production’s technical efficiency in Cambodia. In conclusion, present study strongly recommends the development of irrigation systems and good water management practices to be considered and bring into more effective actions by the central government as well as related agencies for improving rice production in Cambodia in addition to capital investment and improving technical skills of supporting staffs and rural farmers.

In recent years, the problem of ecosystem degradation caused by human activities has become increasingly serious. Vegetation restoration is a key means to solve this problem, which has increased. To address the suitability and structural optimization of vegetation restoration in the Loess Plateau, the MaxEnt model was used to quantify the impacts of environmental and human activities on the planting suitability of vegetation restoration species at the raster scale. Three layers of trees, shrubs, and herbs with 12 common vegetation restoration species were selected. The factor index system was constructed by combining climatic, ecological, and socio-economic data, and the MaxEnt model predicted land suitability. It was found that human activities significantly increased the unsuitable planting area. This especially affected Robinia pseudoacacia in the tree layer and Amorpha fruticosa in the shrub layer. Highly suitable and moderately suitable areas were mainly located in sparsely populated areas with close water sources. Through maximum suitability optimization, it was identified that the overall spatial distribution of the three layers in the study area was relatively consistent, and the structural dominance of trees + shrubs + herbs and single herbs in the vertical structure was obvious, which were concentrated in the southwestern and northeastern parts of the study area, respectively. In addition, organic content (OC) and distance from the road to woodland (RW) were the dominant factors affecting land suitability, with a contribution rate of more than 50% and up to 80%. These results provide a scientific basis for optimizing planting structures. They are of significant theoretical and practical significance in guiding vegetation restoration work.

In this work, we explore a the different forms of a new type of modified gravity, namely f(φ) gravity. We construct the Big Rip type for the energy density and the curvature of the universe. We show that dark energy is a result of the transformation of the field φ mass (dark matter) to energy. In addition, we provide that Ω_{m}≈0,050, Ω_{DM}≈0,2, Ω_{DE}≈0,746, is in excellent agreement with observation data. We explore a generalized formalism of braneworld modified gravity. We also construct a new field equations, which generalize the Einstein field equations. We provide a relation between the extra dimension in 3-brane with the vacuum energy density. We show that the energy density of matter depends directly on the number of dimensions. We manage to find the value of the Gauss-Bonnet coupling α=1/4 which is a good agreement with the results in the literature, this correspondence creates a passage between f(R) gravity and Gauss-Bonnet gravity, this comparison leads to a number of bulk dimensions equal to D=10¹²¹+4.

In many application problems, F-transform algorithms are very efficient. In F-transform techniques, we replace the original signal or image with a finite number of weighted averages. The use of weighted average can be naturally explained, e.g., by the fact that this is what we get anyway when we measure the signal. However, most successful applications of F-transform have an additional not-so-easy-to-explain feature: the partition requirement, that the sum of all the related weighting functions is a constant. In this paper, we show that this seemingly difficult-to-explain requirement can also be naturally explained in signal-measuring terms: namely, this requirement can be derived from the natural desire to have all the signal values at different moments of time estimated with the same accuracy.

As screen sizes are becoming larger and larger, which are beyond human’s physical limitation for direct touching interaction, remote controls are inevitable. However, as techniques applied so far, inertial gyroscopes are susceptible to position inaccuracies, and gesture recognition is limited by cameras’ focus depth and viewing angle. Grating antenna light trapping technology will be an ideal candidate providing the ghost point problem for multipoint inputs can be solved. Therefore, we propose a differential amplitude modulation scheme for grating antenna based multi beam optical touch, which can recognize different incidence points. Where, the amplitude of the incident beams was coded with different pulse width at first. Then, after been trapped by the grating antenna and been transferred into currents by the lined detector arrays, the incident points of the individual beams were recognized and differentiated. The scheme was successfully verified on an 18-inch screen, where two-point optical touch with position accuracy error under 3mm and response time less than 7ms under modulation frequency of 10kHz on both incident beams are obtained. This work paves a practical way for remote multi-point touch, which can make digital mouse in consistent to the users pointing direction obeying natural three-point one ling aiming rule instantaneously.

In this paper we have defined the effect of bulk viscosity on Quintessence model and scaler field potential as well as on classical field. We have shown the same effect for modified gravity with f(R,T)= R+f(T). In the derivation we have predicted the possibility of time dependent evolution of gravitational constant G and anisotropy.

The compatibility between the de Sitter Swampland conjecture and Ho\v{r}ava-Lifshitz $F(\bar{R})$ theories with a flat FLRW metric is studied. We first study the standard $f(R)$ theories and show that the only way in which the dS conjecture can be made independent of $R$ is by considering a power law of the form $f(R)\sim R^{\gamma}$. The conjecture and the consistency of the theory puts restrictions on $\gamma$ to be greater but close to $1$. For the $F(\bar{R})$ theories described by its two parameters $\lambda$ and $\mu$ we use the equations of motion to construct the function starting with an ansatz for the scale factor in the Jordan frame of the power law form. By doing a conformal transformation on the three metric to the Einstein frame we can obtain an action of gravity plus a scalar filed by relating the parameters of the theory. The non-projectable and projectable cases are studied and the differences are outlined. The $F(\bar{R})$ function obtained consists of terms of the form $\bar{R}^{\gamma}$ with the possibility of having negative power terms. The dS conjecture leads to inequalities for the $\lambda$ parameter, in both versions it gets restricted to be greater but close to $1/3$. For the general case in which $\mu$ and $\lambda$ are considered as independent, the action contains an extra term but we propose that the conjecture is still applicable. Once again the non-projectable and projectable cases are studied. The $F$ function obtained has the same form as before, the consistency of the theory and the dS conjecture lead to a set of inequalities on both parameters that are studied numerically. In all cases $\lambda$ is restricted by $\mu$ around $1/3$ and we obtain $\lambda\to1/3$ if $\mu\to0$. Finally we consider the $f(R)$ limit $\mu,\lambda\to1$ and we obtain consistent results.

Litsea martabanica root's antioxidant and AChE activity showed promise as a pesticide detoxification agent in our previous study. In addition to roots, its leaves can help mitigate pesticide exposure, although there is limited scientific evidence supporting their efficacy. However, the use of roots in many countries, such as Thailand, could contribute to environmental degradation, as highland communities traditionally cut down whole trees to obtain them. This study aims to evaluate the antioxidant activity and anti-pesticide potential of water extracts from L. martabanica leaves instead of its roots through in vitro and in vivo investigations. The findings showed that L. martabanica water extracts and fractions demonstrated varied antioxidant activity. The water extract, obtained using traditional extraction methods, was chosen for in vivo experiments. Rats received the extract followed by chlorpyrifos exposure for 16 days. Results indicated reduced acetylcholinesterase activity in chlorpyrifos-exposed rats, while treatment with leaf extract led to increased activity, suggesting its potential as a detoxifying agent. Histopathological examination revealed no liver cell necrosis and showed liver cell regeneration, indicating potential protection against free radical-induced liver damage without affecting rat liver weight or biochemical profiles. Utilizing L. martabanica leaves for healthcare purposes holds promise without negative environmental impact.

Fluorescence microscopy is an important tool for disease diagnosis, often requiring costly optical components, such as fluorescence filter cubes and high-power light sources. Due to its high cost, conventional fluorescence microscopy cannot be fully exploited in low-income settings. Smartphone-based fluorescence microscopy becomes an interesting low-cost alternative, but raises challenges in the optical system. We present the development of a low-cost inverted laser fluorescence microscope, that uses a smartphone to visualize the fluorescence image of biological samples. Our fluorescence microscope uses a laser-based simplified optical filter system, that provides analog optical filtering capabilities of a fluorescence filter cube. Firstly, we validated our inverted optical filtering by visualizing microbeads labeled with three different fluorescent compounds or fluorophores, commonly used for disease diagnosis. Secondly, we validated the disease diagnosis capabilities, by comparing the results of our device with those of a commercial fluorescence microscope. We successfully detected and visualized Trypanosoma cruzi parasites, responsible of the Chagas infectious disease, and the presence of Antineutrophil cytoplasmic antibodies of the ANCA non-communicable autoimmune disease. The samples were labeled with the fluorescein isothiocyanate (FITC) fluorophore, one of the most commonly used for disease diagnosis. Our device provides a 400 X magnification and is at least two orders magnitude cheaper than conventional commercial fluorescence microscopes.

The perovskite solar cells (PSCs) have been significantly improved by utilizing inorganic hole transporting layer (HTL), such as nickel oxide. Despite the promising properties, there are still limitations due to defects. Recently, research on self-assembled monolayers (SAM) is being actively conducted, which show promise in reducing defects and enhancing device performance. In this study, we successfully engineered a p-i-n perovskite solar cell structure utilizing HC-A1 and HC-A4 molecules. These SAM molecules were found to enhance the grain morphology and uniformity of the perovskite film, which are critical factors in determining optical properties and device performance. Notably, HC-A4 demonstrated superior performance due to its distinct hydrophilic properties with a contact angle of 50.3°, attributable to its unique functional groups. Overall, the HC-A4 applied film exhibited efficient carrier extraction properties, attaining a carrier lifetime of 117.33 ns. Furthermore, HC-A4 contributed the superior device performance with its favorable band alignment, achieving the highest device efficiency of 20%.

The Indian meal moth, Plodia interpunctella, poses a significant threat to global agricultural products. Although pheromone-based technologies show promise for P. interpunctella management, limitations like single-sex targeting necessitate exploring complementary strategies. Vegetable-based oils represent a potential alternative, but their efficacy, sex-specificity, and interaction with sex pheromones remain unclear. To answer these questions, we first examined attraction of P. interpunctella female and male adults to ten different vegetable oils, i.e., camellia, corn, olive, peanut, rapeseed, sesame, soybean, sunflower, walnut, and a blended oil (mixture of sunflower seed, rapeseed, soybean, peanut, and sesame oils), in the semi-field conditions. Sesame, olive, and blended oils demonstrated most attractive, capturing significantly more adults compared to other oils. We then evaluated effectiveness of these three attractive oils and their combinations with P. interpunctella sex pheromone in a grain warehouse. Traps baited with these oils captured significantly more females and males compared to control traps without attractants. However, sex pheromone addition did not improve male capture and significantly reduced female capture, suggesting an inhibitory effect. Our findings highlight the potential of blended, olive, or sesame oil trap alone as alternative monitoring and trapping tools for P. interpunctella, delivering novel insights into the development of efficient integrated pest management strategies for stored products.

Advances in reconfigurable liquid-based reconfigurable antennas are enabling new possibilities to fulfil the requirements of more advanced wireless communication systems. In this review, a comparative analysis of various state-of-the-art concepts and techniques for designing reconfigurable antennas using liquid is presented. First, the electrical properties of different liquids at room temperature commonly used in reconfigurable antennas are identified. This is followed by a discussion of various liquid actuation techniques in enabling high frequency reconfigurability. Next, liquid-based reconfigurable antennas in literature used to achieve the different types of reconfiguration will be critically reviewed. These include frequency-, polarization-, radiation pattern- and compound reconfigurability. The current concepts of liquid-based reconfigurable antennas can be classified broadly into three basic approaches: altering the physical (and electrical) dimensions of antennas using liquid, applying liquid-based sections as reactive loads; and implementation of liquids as dielectric resonators. Each concept and their design approaches will be examined, outlining their benefits, limitations, and possible future improvements.

This research work was aimed at investigating and determining the depth resolution of a 500Mhz GPR Antenna. The survey was conducted in an open space at the Physics Department, College of science-KNUST. The MALA GPR equipment with 500MHz shielded Antenna in the common offset-mode was used to investigate the depth at which materials were buried. Concrete block, tree roots, plastic bottle with water, glass bottle and Electric wire were each buried in cavities with five different burial depths. The real depth of each material was measured both along and across the cavity and compared to their corresponding GPR measured depth. The comparison of the Real depth and the GPR depth showed almost identical depth measurements with a root mean square deviation of 0.028m. The implication of this is that the 500 Mhz GPR antenna can accurately locate and detect the position of buried materials in the subsurface at a depth within the range (0.20-0.66) m.

A wideband antenna with excellent efficiency is the most important requirement of wireless communication. There are many ways to improve the antenna bandwidth, such as using a low permittivity substrate, increasing the substrate thickness, and using different shapes of radiating patches. However, this cannot achieve wideband. This problem can be solved by using a metamaterial-based microstrip antenna that can achieve wideband. The proposed patch antenna has a metamaterial unit cell loaded on the top patch and on the bottom ground plane. The top unit cell, which consists of a square loop with Complementary Split Ring Resonator (CSRR) and the bottom unit cell, which is a Square Shaped Cross-Slot (SSCS), is loaded on the patch and ground. The objective is to achieve a compact metamaterial-loaded antenna with enhanced radiation characteristics and to design a metamaterial antenna for wideband applications. The wideband and high gain features of the proposed antenna make it suitable for 5G NR FR1 and Wi-Fi 6E applications.

An antenna sensor is proposed to execute dual functions of antenna and sensor in the wireless sensor system, in order to reduce data loss and to increase transmission rate by omitting a certain interface. The as-made sensor was test at a center frequency of 46 MHz for measuring human finger postures using principle of dipole antenna. The antenna sensor was attached on a wearable glove. The results showed that the motion sensor can accurately identify finger angles at 0°, 20°, 40°, 60° and 80°.

We investigate alternative candidates to dark energy that can explain the current state of the universe in the framework of the generalized teleparallel theory of gravity f(T ) where T denotes the torsion scalar. To achieve this, we carried out a series of reconstruction taking into account to the ordinary and entropy-corrected versions of the holographic and new agegraphic dark energy models. These models used as alternative to dark energy in the literature in order describe the current state of our universe. It is remarked that the models reconstructed indicates behaviors like phantom or quintessence models. Furthermore, we also generated the EoS parameters associated to entropy-corrected models and we observed a transition phase between quintessence state and phantom state as showed by recent observational data. We also investigated on the stability theses models and we created the {r − s}. The behavior of certains physical parameters as speed of sound and the Statefinder parameters are compatible with current observational data.

In this work we present a novel steganography algorithm, based on Fractal Transform domain, combined with the principles of Cryptography. The proposed method uses a private key, which will indicate which segment of the image will be taken and encoded with the Fractal Transform, to then insert the secret bits in the transformed coefficients, thus generating the stego image.

The objective of this study was to investigate the umami characteristics of soy sauce using electronic tongue evaluation and amino acid composition and Matrix-assisted laser desorption ionization-time of flight mass spectrometry (MALDI-TOF MS) analysis. The soy sauce peptides were isolated from soy sauce using XAD-16 macroporous resin combined with ethanol solution. Results showed that the soy sauce peptide fraction eluted by 60% ethanol (SS-60%) exhibited a prominent umami taste and the umami scores were highly positively correlated with the amino acid nitrogen contents of soy sauces. The umami scores of SS-60% were significantly positively correlated with the contents of free amino acids. Especially, Phe showed the highest positive correlation with the umami scores. In addition, five characteristic ion peaks with m/z at 499, 561, 643, 649, and 855 were identified in the peptide mass fingerprinting. Therefore, this study provides new insights into the umami characteristics for the flavor evaluation and reality identification of soy sauce.

Temperature Cycle Induced Deracemization (TCID) offers a promising approach to obtain enantiopure solids from racemic mixtures. By combining rapid racemization in solution and temperature swings, homochirality is theoretically achieved. Despite theoretical expectations of doubled yields compared to traditional chiral separation methods, such as in Preferential Crystallization, experimental validation remains lacking. We applied TCID to (1-(4-chlorophenyl)-4,4-dimethyl-2-(1H-1,2,4-triazol-1-yl) pentan-3-one) (Cl-TAK), introducing a post-TCID cooling step to enhance yield and a washing step to augment enantiopurity. This refinement yielded an 89.8% mass yield with 99.1% enantiomeric excess in the crystal phase (c.e.e.) within 24 hours on an 8.75g scale, showcasing improved performance with insignificant process duration extension. Additionally, we explored the stochasticity of deracemization, observing the development from low initial crystal enantiomeric excesses(1-6% c.e.e0) at a 2.5 g scale. Kinetic analysis revealed that a 2% c.e.e0 effectively mitigates chiral flipping risks and induction time in our system. Our study underscores the potential for reduced initial c.e.e. to expedite deracemization and presents a straightforward method to optimize yield and purity, facilitating industrial application.

In order to properly cover different scenarios, radiation patterns of antennas should be accordingly adjusted before fabrication. However, most antennas are unable to provide both broadside beam and designable conical beam which are usually-used radiation patterns for radio coverage. In this paper, a planar Circular Polarized (CP) annular Leaky-Wave Antenna (LWA) with conical beam is proposed, which is realized on annular Substrate-Integrated Waveguide (SIW). Broadside beam or conical beam could be easily obtained by fabricating the LWA with modified structural parameters. The central operating band is 5.8 GHz. The LWA allows only the -1th spatial harmonic to radiate, while the fundamental wave and other spatial harmonics are suppressed in slow wave mode. In order to validate the design effectiveness, two examples for broadside beam and conical beam radiation are fabricated and measured. The measurement results show good agreement with the simulation results. The proposed LWA presents a promising radiation performance and is a good candidate for wireless communication applications.

This paper is primarily focused on the robust control of an inverted pendulum system based on the policy iteration in reinforcement learning. First, a mathematical model of the single inverted pendulum system is established through a force analysis of the pendulum and trolley. Second, based on the theory of robust optimal control, the robust control of the uncertain linear inverted pendulum system is transformed into an optimal control problem with an appropriate performance index. Moreover, for the uncertain linear and nonlinear systems, two reinforcement-learning control algorithms are proposed using the policy iteration method. Finally, two numerical examples are provided to validate the reinforcement learning algorithms for the robust control of the inverted pendulum systems.

Laser-induced graphene (LIG) has gained considerable attention recently due to its unique properties and potential applications. In this study, we investigate using LIG in polyimide (PI) as a material for antenna applications. The LIG-PI composite material was prepared by a facile picosecond laser (1064 nm) irradiation process, which resulted in a conductive graphene network within the PI matrix. Furthermore, LIG formation was confirmed by Raman spectroscopy and sheet resistance measurements. Finally, a patch antenna from LIG for 2.45 GHz microwaves was simulated, produced and tested. These findings suggest that LIG-PI composites have great potential for use in high-frequency electronic devices and can provide a new avenue for the development of flexible and wearable electronics.

We study the effect of oblique illumination on the functioning of a plasmonic nanoantenna for chiral light. The antenna is designed to receive a structured beam of light and produce a nanosized near-field distribution that possesses non-zero orbital angular momentum. The design consists of metal (gold) micro-rods laid on a dielectric surface and is compatible with well-developed nanofabrication techniques. Experimental arrangements often require such an antenna to operate in a tilted geometry, where input light is incident on the antenna at an oblique angle. We analyze the limitations that the angled illumination imposes and discuss approaches to mitigate these limitations. Through our numerical simulations, we find that tilt angles larger than 30 degrees require modifications to the antenna design. Our analysis guides current and future experimental configurations to pushing the limits of resolution and sensitivity.

Cotton (Gossypium spp.) is the most important fibre crop worldwide. Black root rot and Fusarium wilt are two major diseases of cotton caused by soil-borne Berkeleyomyces rouxiae and Fusarium oxysporum f. sp. vasinfectum (Fov), respectively. Phenotyping plant symptoms caused by soil-borne pathogens has always been a challenge. To increase the uniformity of infection, we adapted a seedling screening method that directly uses liquid cultures to inoculate the plant roots and the soil. Four isolates each of B. rouxiae and Fov were collected from cotton fields in Australia and were characterised for virulence on cotton under controlled plant growth conditions. While the identity of all four B. rouxiae isolates were confirmed by multi-loci sequencing, only two of them were found to be pathogenic on cotton, suggesting variability in the ability of isolates of this species to cause disease. The four Fov isolates were phylogenetically clustered together with the other Australian Fov isolates and displayed both external and internal symptoms characteristic of Fusarium wilt on cotton plants. Furthermore, the isolates appeared to induce varied levels of plant disease severity indicating differences in their virulence on cotton. To contrast the virulence of the Fov isolates, four putatively non-pathogenic Fusarium oxysporum (Fo) isolates collected from cotton seedlings exhibiting atypical wilt symptoms were assessed for their ability to colonise cotton host. Despite the absence of Secreted In Xylem genes (SIX6, SIX11, SIX13 and SIX14) characteristic of Fov, all four Fo isolates retained the ability to colonise cotton and induce wilt symptoms. This suggests that slightly virulent strains of Fo may contribute to the overall occurrence of Fusarium wilt in cotton fields. Findings from this study will allow better distinction to be made between plant pathogens and endophytes and allow fungal effectors underpinning pathogenicity to be explored.

Here are given tight probabilistic inequalities that provide nearly best estimates for the Csiszar's f-divergence. These use the right and left psi -Hilfer fractional derivatives of the directing function f. Csiszar's f- divergence or the so called Csiszar's discrimination is used as a measure of dependence between two random variables which is a very essential aspect of stochastics, we apply our results there. The Csiszar's discrimination is the most important and general measure for the comparison between two probability measures. We give also other applications.

Croton L. (Euphorbiaceae) is a very specious genus and consists of about 1,250 species, mainly distributed in tropical Asia and China. The first complete plastome sequence from the genus, Croton tiglium, is reported in this study (NCBI acc. No. MH394334). The plastome is 150,021 bp in length. The lengths of LSC and SSC are 111,654 bp and 18,167 bp, respectively. However, the length of the IR region is only 10,100 bp and includes only four rrn and four trn genes, and a small part of the ycf1 gene. We propose two-step IR contractions to explain this unique IR region of the C. tiglium plastome. First, the IR contracted from rps19-rpl2 to ycf2-trnL-CAA on the LSC/IRb boundary. Second, the IR contracted from ycf2-trnL-CAA to rrn16-trnV-GAC on the LSC/IRa boundary. In addition, duplicated copies of psaI genes were discovered in the C. tiglium plastome. Both copies were located side by side between accD and ycf4 genes, but one copy was pseudogenized because of a five-basepair (TAGCT) insertion in the middle of the gene following frameshift mutation. The plastome contains 112 genes, of which 78 are protein-coding genes, 30 are tRNA genes, and four are rRNA genes. Sixteen genes contain one intron and two genes have two introns. The infA gene is lost. Twelve large repeats were detected in the plastome. All large repeats are located in the LSC region. Also, 272 simple sequence repeats (SSRs) were identified. The penta-SSRs accounted for 45% of total SSRs, followed by mono- (32%), di- (12%), tetra (6%) and tri-SSRs (5%). Most of them were distributed in the large single copy (LSC) region (85%). In addition, 76% of the SSRs were located in the intergenic spacer (IGS). Phylogenetic analysis suggested that C. tiglium is a sister group of Jatropha curcas with 100% bootstrap support. Seven Euphorbiaceae species formed one clade with 100% bootstrap support.

Revealing the spatial distribution mechanism of the coupling effect between soil water and salt is essential for managing saline-alkali farmland. This study utilized the multifractal method to analyze soil water and salt under varying water content levels in arid saline-alkali farmland. Soil samples were collected on the second (S1), fifth (S2), eighth (S3), eleventh (S4), and fourteenth (S5) days after a rainfall event. The findings showed that a significant decrease in soil water content, contrasting with an increase in soil salt content throughout the soil layers post-rainfall. As water content decreased, the spatial variability of soil water initially increased from S1-3 and then decreased, while the spatial variability of soil salt decreased. The spatial distribution between soil water and salt exhibited a high correlation at S3-4 (with relative water content of soil ranging from 0.52 to 0.75) due to their coupling effect. However, soil salt was unevenly leached by rainfall at high water content levels (S1-2) and precipitated at low water content levels (S5), resulting in low spatial variability correlations between soil water and salt. This study elucidated the coupling process of soil water and salt, identifying their spatiotemporal distribution mechanism in dryland agricultural areas.

The hydrocarbon generation potential of Chia Gara strata and their genetic link with produced oils from the Zagros basin are still not comprehensively investigated. Forty-seven rock samples from the Tithonian–Berriasian interval were subjected to geochemical analyses to infer organic matter enrichment, hydrocarbon potential, thermal maturity, and timing for hydrocarbon generation/expulsion and their implications regarding upcoming petroleum explorations in the Zagros basin. The results showed that the Chia Gara rock samples have fair to very-good generation potential, as confirmed by higher total organic carbon (TOC=0.68–3.95 wt%) and Rock-Eval (S1+S2=3.37–8.52 mg HC/g rock). The hydrogen index (HI=171–462) and Rock-Eval Tmax over 430 °C support the presence of Types II and mixed Types II/III kerogen. These results confirm the high generation potential of the Chia Gara Formation in the study region. 1D basin models of the KK–109 well show that over 55% of kerogens were converted into oil in the Cretaceous (77–67 Ma). Expulsion started from the Miocene until now (22–0 Ma), consistent with 0.71–0.80 of modeled Easy%Ro and 55–80 %TR. Consequently, this project confirms the potential oil expulsion from the Chia Gara Formation, which can be a resource for upcoming hydrocarbon investigation in the Zagros basin, Iraq.

Dental polymers are often advertised and selected for use in restorations based upon the flexural strength of prefabricated discs, which may not accurately reflect their performance in dental applications. The objectives of this study were, therefore, to determine whether the three-point bending (3PB) test for flexural strength would be predictive of the “crunch-the-crown” CTC test for the failure load. Three brands of polymers (Trilor, Juvora, and Pekkton) were fabricated into rectangular bars and fully contoured crowns (10 specimens of each polymer brand, 30 specimens of each shape). Bars were tested in 3PB to determine flexural strength, and crowns were CTC tested to determine failure load after luting to resin abutments. Statistical significance was evaluated by one-way ANOVA ( = 0.05) and Pearson’s correlation coefficient. The fracture mechanisms were characterized by scanning electron microscopy (SEM). There were significant differences (p < 0.05) in the mean crown failure loads (Trilor [7,033 N] > Juvora [5,217 N] > Pekkton [3,023 N]) and mean flexural strengths of the bars (Trilor [468 MPa] > Juvora [197 MPa] = Pekkton [192 MPa]). There were no correlations between flexural strength and failure load. The mode of crown fracture was different between the polymers, and included deformation (Juvora), ductile-to-brittle fracture (Pekkton), and a combination of cracks and deformation (Trilor). The flexural strength was not correlated with the corresponding crown failure load. Dental practitioners should not rely on the value of flexural strength obtained from the three-point bending test, as advertised from the manufacturer, to predict the performance of polymeric crowns.

Ground penetrating radar (georadar, GPR), widely used in geology, archeology and road construction, is an efficient tool for searching and studying subsurface objects and structures. When planning GPR missions, it is necessary to predict the resolution of the device and the achievable probing depth. The article discusses the methods and results of assessing these characteristics of the Loza-V and Loza-N radars obtained in the course of archaeological and geographical expedition works.

In bone tissue engineering, ceramics have been the choice due to their excellent biological properties. But the paradigm changed with the discovery of bioactive glasses (BGs) in 1969 by Larry Hench and co-workers, due to their ability to bond to living tissues through the formation of an interfacial bone-like hydroxyapatite layer when the bioglass was put in contact with biological fluids in vivo. Among a number of tested compositions, the one exhibiting the highest bioactivity index is the well-known trademarked 45S5 Bioglass®. The topic received increasing attention particularly after 1985 when this material entered in the market of biomedical devices, inspiring many other investigations aiming at further exploring the in vitro and in vivo performances of this BG, or developing other related BG compositions. The research efforts gradually revealed a number of shortcomings of 45S5 Bioglass®, mostly derived from its high sodium content, initially intended to decrease the melting temperature and accelerating the degradation of the silicate network over time. But the extensive release of sodium from 45S5 Bioglass® in the biological fluids creates a high pH cytotoxic environment. Other serious drawbacks include a fast degradation rate, and a poor sintering ability, which hinders the reliable fabrication of porous scaffolds. Therefore, sol-gel was regarded as an attractive alternative to prepare alkali-free BG compositions. The process uses inorganic and/or organic precursors, which undergo hydrolysis and condensation at room-temperature, being less costly. When properly conducted, the sol-gel process might result in amorphous structures with all the components intimately mixed at the atomic scale. Moreover, developing new better performing materials for bone tissue engineering is a growing concern, as the ageing of the world’s population leads to lower bone density and osteoporosis. This work describes the sol-gel synthesis of a novel quaternary silicate-based BG with the composition 60 SiO2 – 34 CaO – 4 MgO – 2 P2O5 (mol%) was prepared using acidified distilled water as single solvent. By controlling the kinetics of the hydrolysis and condensation steps, an amorphous glass structure could be obtained. The results of XRD of samples calcined within the temperature range from 600-900 ºC demonstrated that amorphous nature was maintained until 800 ºC, followed by partial crystallization at 900 ºC. The specific surface area, an important factor in osteoconduction, was also evaluated over different temperatures, ranging from 160.6 ± 0.8 m2/g at 600 ºC down to 2.2 ± 0.1 m2/g at 900 ºC, being accompanied consistent changes in average pore size and agreeing pore size distribution. The immersion of the BG particles in simulated body fluid (SBF) led to the formation of an extensive apatite layer on its surface. These overall results indicate the proposed material is very promising for biomedical applications in bone regeneration and tissue engineering.

The terahertz (THz) frequency range, often overlooked in the past, is now gaining recognition for its unique properties and diverse applications. THz waves, positioned between microwave and infrared frequencies, offer safety, broad bandwidth, and low energy consumption. This review highlights the burgeoning importance of THz technology in communication systems, spectroscopy, biomedical imaging, and various industries. It emphasizes the significance of novel antenna designs in enhancing THz system performance and functionality, enabling rapid communication, data transmission, spectroscopic analysis, and sensor capabilities.

This paper focuses on the combination of the method of moments and the wire-grid approximation as an effective computational technique for modeling symmetrical antennas with low computational cost and quite accurate results. The criteria and conditions for the use of wire-grid surface approximation from various sources are presented together with new recommendations for modeling symmetrical antenna structures using the wire-grid approximation. These recommendations are used to calculate the characteristics of biconical and horn antennas at different frequencies. The results obtained using different grid and mesh settings are compared to those obtained analytically. Moreover, the results are compared to those obtained using the finite difference time domain numerical method, as well as the measured ones. All results are shown to be in a good agreement. The used recommendations for building a symmetrical wire-grid of those symmetrical antenna elements provided the most advantageous parameters of the grid and mesh settings and the wire radius, which are able to give a quite accurate results with low computational cost. Additionally, the known equal area rule was modified for a rectangular grid form. The obtained radiation patterns of a conductive plate using both the original rule and the modified one are compared with the electrodynamic analysis results. It is shown that the use of the modified rule is more accurate when using a rectangle grid form.

In this paper a low profile antenna is presented for wideband communication applications. The presented design is consists of an I-shape driven strip and a rectangular ground strip with an open slot in the middle and steeped lower portion. Measured result demonstrates that the achieved operating band of the proposed antenna has the potential to cover Global Star Satellite Phones (1.61-1.63 GHz, uplink), Advanced Wireless Systems (1.71-1.76 GHz, 2.11-2.17 GHz), DCS (1710-1880 MHz), GSM (1800MHz), DCP (1.88-1.90 GHz), DCS-1900/PCS/PHS (1850-1990MHz), WCDMA/IMT-2000 (1920-2170MHz), UMTS (1920-2170 MHz), LTE bands (FDD LTE bands 1-4, 9-10, 15-16, 23-25, 33-37, 39). The designed antenna possessed a very small size of 0.35λ0 × 0.027λ0 at the lowest frequency (S11 ≤ -10dB) and achieved good gain, exhibits stable radiation patterns which make it suitable for handheld communication devices.

In this research paper, design and development of pyramidal horn antenna for J-band application is reported. It is particularly designed for 17 dB gain and half beam width about 25 degrees at 6.93 GHz. Horn aperture, horn axial length and distance from the throat of the antenna to aperture are the main design constraints which are calculated and used for the antenna design and simulation. Beam width in E-plane and H-plane horn is calculated and it is 19.18 dB and 22.86 dB respectively. The reported antenna design shows good performance for J-band in radiometry, satellite, and radar applications.

Efficient beam steerable high-gain antennas enable high-speed data rates over long-distance networks, including wireless backhaul, satellite communications (SATCOM), and SATCOM On-the-Move. These characteristics are essential for advancing contemporary wireless communication networks, particularly within 5G and beyond. Various beam-steering solutions have been proposed in the literature, with passive beam-steering mechanisms employing planar metasurfaces emerging as cost-effective, power-efficient, and compact options. These attributes make them well-suited for use in confined spaces, large-scale production and widespread distribution to meet the demands of the mass market. Utilizing a dual-band antenna terminal setup is often advantageous for full duplex communication in wireless systems. Therefore, this article presents a comprehensive review of the dual-band beam steering techniques for enabling full-duplex communication in modern wireless systems, highlighting their design methodologies, scanning mechanisms, physical characteristics, and constraints. Despite the advantages of planar metasurface-based beam steering solutions, literature on dual-band beam steering antennas supporting full duplex communication is limited. This review article identifies research gaps and outlines future directions for developing economically feasible passive dual-band beam-steering solutions for mass deployment.

A Friedmann-Lemaitre-Robertson-Walker space-time model with all curvatures k=0,±1 is explored in f(R,T) gravity. The solutions are obtained via the parametrization of the scale factor that leads to a model transiting from a decelerated universe to an accelerating one. The physical features of the model are discussed and analysed.

We analyze the behavior of relativistic spherical objects within the context of modified $f(R,T)$ gravity considering Tolman VI spacetime, where gravitational lagrangian is a function of Ricci scalar(R) and trace of energy momentum tensor(T) i.e,$ f(R,T)= R+ 2\beta T$, for some arbitrary constant $\beta$. For developing our model, we have chosen $\pounds_{m} = -p$, where $ \pounds_{m}$ represents matter lagrangian. For this investigation, we have chosen three compact stars namely PSR J1614-2230 [Mass=(1.97$\pm$ 0.4)M$_\odot$; Radius= 9.69$_{-0.02} ^{+0.02}$ Km] ,Vela X-1 [Mass=(1.77$\pm$ 0.08)M$_\odot$; Radius= 9.560$_{-0.08} ^{+0.08}$ Km] and 4U 1538-52 [Mass=(9.69)M$_\odot$; Radius= 1.97 Km]. In this theory the equation of pressure isotropy is identical to standard Einstein's theory. So all known metric potential solving Einstein's equations are also valid here. In this paper, we have investigated the effort of coupling parameter ($\beta$) on the local matter distribution. Sound of speed and adiabatic index are higher with grater values of $\beta$ while on contrary mass function and gravitational redshift are lower with higher values of $\beta$ . For supporting the theoretical results, graphical representation are also employed to analyze the physical viability of the compact stars.

The radio spectrum is a scarce and extremely valuable resource that demands careful real-time monitoring and dynamic resource allocation. Dynamic spectrum access (DSA) is a new paradigm for managing the radio spectrum, which requires AI/ML driven algorithms for optimum performance under rapidly changing channel conditions and possible cyber-attacks in the electromagnetic domain. Fast sensing across multiple directions using array processors, with subsequent AI/ML based algorithms for sensing and perception of the waveforms that are measured from the environment is critical for providing decision support in DSA. As part of directional and wideband spectrum perception, the ability to finely channelize wideband inputs using efficient Fourier analysis is much needed. However, a fine-grain fast Fourier transform (FFT) across a large number of directions is computationally intensive and leads to high chip area and power consumption. We address this issue by exploiting recently proposed approximate discrete Fourier transforms (ADFT) which has its own sparse factorization for real-time implementation at low complexity and power consumption. The ADFT is used to create a wideband multi-beam RF digital beamformer and temporal spectrum-based attention unit which monitors 32~discrete directions across 32~sub-bands in real-time using a multiplierless algorithm having low computational complexity. The output of this spectral attention unit is applied as a decision variable to an intelligent receiver that adapts its center frequency and frequency resolution via FFT channelizers that are custom-built for real-time monitoring at high resolution. This two-step process allows the fine-gain FFT to be applied only to directions and bands of interest as determined by the ADFT based low-complexity 2D spacetime attention unit. The fine-grain FFT provides a spectral signature that can find future use cases in neural network engines for achieving modulation recognition, IoT device identification, and RFI identification. Beamforming and spectral channelization algorithms, digital computer architecture, and early prototypes using a 32-element fully digital multichannel receiver and field programmable gate array (FPGA)-based high-speed software defined radio (SDR) is provided.

Qatar and other Gulf States have a diverse range of marine vegetation that is adapted to the stressful environmental conditions of seawater. The industrial wastewater produced by oil and gas activities adds further detrimental conditions for marine aquatic photosynthetic organ-isms on the Qatari coastlines. Thus, these organisms experience severe stress from both seawater and industrial wastewater. This review discusses the biodiversity in seawater around Qatar, as well as remediation methods and metabolic pathways to reduce the negative impacts of heavy metals and petroleum hydrocarbons produced during these activities. These methods include phyto-stabilization phyto-accumulation, phyto-volatilization, and phyto-degradation. Phy-to-degradation in particular is discussed in detail, including metabolic pathways such as alkane and aromatic-compound degradation pathways. The role of microorganisms that are adjacent to or associated with these aquatic marine organisms is discussed, including rhizosphere biodeg-radation. In this type of biodegradation, exudates are released by plant roots and supply nutrients to microorganisms in the rhizosphere, which enhances their ability to degrade organic pollutants. Special attention is paid to mangrove forests and their roles in remediating shores polluted by industrial wastewater. Seagrasses (Halodule uninervis, Halophila ovalis, and Thalassia hemprichii) and seaweeds (Chlorophyta, Phaeophyta, and Rhodophyta) around the peninsula of Qatar are also discussed.

This paper mainly analyzes the design and control of the rotational inverted pendulum, and presents a state space expression. Since the system is highly unstable a feedback control system is used. Augmentations with weighting functions based mixed sensetivity and H2 optimal control methods are used to make the system stable for uprise position. The rotational inverted pendulum have been simulated and compared with the proposed controllers and a promising results have been analyzed sussesfuly.

In this work, we introduce a new concepts for $\alpha$-type $F$-Suzuki contraction and $\alpha$-type $F$-weak-Suzuki contraction in the context of $b$-metric spaces. Compared to the $\alpha$-type $F$-contraction and $F$-Suzuki contraction mappings, these contractions are essentially weaker. For these type of contraction mappings, sufficient conditions are established for the fixed point's existence and uniqueness in $b$-metric spaces. As a result, the findings encompass several generalizations. To show the usability of our obtained results, we provide a supportive example and an application to a non-linear differential equation with fractional order.

In this paper, we have proposed an effective metasurface design to accomplish cloaking of equilateral patch antennas and their array configuration. As such, we have exploited the concept of electromagnetic invisibility, employing the mantle cloaking technique with the intention to eliminate the destructive interference ensuing between two distinct triangular patches situated in a very congested arrangement (sub-wavelength separation is maintained between the patch elements). Basically, we demonstrate that implementation of the planar coated metasurface cloaks onto the patch antenna surfaces compels them to become invisible to each other, at the intended frequencies. In effect, an individual antenna element does not sense the presence of the other, in spite of being in a rather close vicinity. We also exhibit that the cloaks successfully reinstate the radiation attributes of each antenna in such a way that it emulates their respective performance in an isolated environment. Moreover, we have extended the cloak design to an interleaved one dimensional array of the two patch antennas and it is shown that the coated metasurfaces assure efficient performance of each array in terms of their matching as well as radiation characteristics, in turn, enabling them to radiate independently for various beam-scanning angles.

Decoherence with recurrences appear in the dynamics of the one-body density matrix of an $F = 1$ spinor Bose-Einstein condensate, initially prepared in coherent states, in the presence of an external uniform magnetic field and within the single mode approximation. The phenomenon emerges as a many-body effect of the interplay of the quadratic Zeeman effect, that breaks the rotational symmetry, and the spin-spin interactions. By performing full quantum diagonalizations very accurate time evolution of large condensates are analyzed, leading to heuristic analytic expressions for the time dependence of the density matrix, in the weak and strong interacting regimes. We are able to find accurate analytical expressions for both the decoherence and the recurrence times, in terms of the number of atoms and strength parameters, that show remarkable differences depending on the strength of the spin-spin interactions. We discuss the nature of these limits in the light of the thermodynamic limit.

The advances mobile communications has seen in recent years has rendered the radio spectrum a limited and, hence, an expensive resource. Therefore, technologies that support unlicensed access to spectrum are needed. Therefore, the adoption of novel modulation schemes becomes of utmost importance to obtain better spectral-localization and reduce the OOBE (\textit{Out of Band Emission}) inherent to OFDM (\textit{Orthogonal Frequency Division Multiplexing}) and, consequently, mitigating the interference between secondary (\textit{unlicensed}) and primary users. In this scenario, we assess the gain in the bit error probability using f-OFDM (\textit{filtered-OFDM}) in MIMO systems, both used in the 5G RANGE project.

Research into improving the functionality and capacities of wearable technology has surged as a result of its fast progress. The functioning of wearable technology is largely dependent on antenna design, which provides wireless connectivity and communication. This study of the literature searches many online sources for pertinent research on the various antenna designs for wearable technology. The findings verified that the materials vary based on the design being employed. An analysis was conducted on the gain, frequency, materials, and sizes. The review excels at synthesizing research and literature despite its restricted resources.

The work contains a detailed analysis of the electromagnetic field originating from a point source placed above the layered structure.The surface impedance of the multilayer dielectric structure was determined. Based on the boundary conditions, a method for determining the surface impedance of a layered structure with a perfectly conductive screen and or a magnetic screen is presented. The resonance conditions and the conditions for the excitation of surface waves are derived. The integral expression defining the generalized impedance was analyzed with a view to adapting it to numerical implementation. This allowed the development of a computer program based on which calculations were made of the effect of excitation of waves on multilayer dielectric substrates.

One of the future challenges of increasing the harnessed solar power is efficiency using of CubeSat sides. One of the approaches is using integrated antenna systems with solar panels or payloads. This study proposes a new approach to the use of integrated antenna systems in remote sensing missions. In this approach, due to the integration of antenna system with payload (in our case, with camera), it is possible to achieve a significant increase in the power generation. Calculations are carried out for cases when the antenna system are integrated with the optical system (α = 0°), which implies that they use one plane, in the second case they are spaced at an angle of α = 90° and in the third case when they are directed to opposite sides (α =180°). In the case of α = 0°, where the camera and antenna module are aligned co-axially, there is no energy expenditure for CubeSat orientation. However, in the other two cases, energy is required for rotation and maintenance of the specified orientation throughout the entire duration of the satellite's flight over the ground station, amounting to 111.99 mW when α = 90° and 44.33 mW when α = 180°.

This article presents a wide-band antenna designed for the Cube Satellite (CubeSat). Based on a quadrifilar structure, the antenna provides circular polarization radiation, which is suitable for satellite communication. Moreover, the antenna is designed and fabricated using two 1.6 mm thickness FR4-Epoxy boards that connect together by the metal pins. In order to improve the robustness, a ceramic spacer is placed in the centerboard, and four screws at the corners are added to fix the antenna with the CubeSat structure. These additional parts reduce antenna damage caused by vibrations in the launch vehicle lift-off stage. The proposal has a dimension of 77mm x 77mm x 10mm and covers the LoRa frequency bands of 868 MHz, 915 MHz, and 923 MHz. According to the measurements in an anechoic chamber, antenna gains are obtained with the values of 2.3 dBiC and 1.1 dBiC for the 870 MHz and 920 MHz, respectively. Finally, the antenna is integrated into a 3U CubeSat that was launched by a Soyuz launch vehicle. The terrestrial-to-space communication link was measured, and the antenna performance was confirmed in the real-life scenario.

In this paper a full state feedback control of a double inverted pendulum on a cart (DIPC) are designed and compared. Modeling is based on Euler-Lagrange equations derived by specifying a Lagrangian, difference between kinetic and potential energy of the DIPC system. A full state feedback control with H infinity and H 2 is addressed. Two approaches are tested: open loop impulse response and a double inverted pendulum on a cart with full state feedback H infinity and H 2 controllers. Simulations reveal superior performance of the double inverted pendulum on a cart with full state feedback H infinity controller.

In this paper, we classify the function space of all real-valued functions on R denoted as F(R,R) into 28 distinct blocks. Each block contains elements that share common features in terms of the cardinality of their sets of continuity and differentiability. Alongside this classification, we introduce the concept of the Connection, which reveals a special relationship structure between four well-known real-valued functions in real analysis: the Cantor function, Dirichlet function, the Thomae function, and the Weierstrass function. Despite the significance of this field, several perspectives remain unexplored.

A locally-rotationally-symmetric Bianchi-I model filled with strange quark matter (SQM) is explored in f(R, T) gravity. We take f(R, T) = R + 2 f(T) = R + 2λT, where R is the Ricci scalar, T is the trace of energy-momentum tensor and λ is an arbitrary constant. Exact solutions are obtained by assuming that the expansion scalar is proportional to the shear scalar. This yields a constant value for the deceleration parameter, q = 2, which corresponds to the decelerated phase of the universe. The model is found to be physically viable for λ < −1. SQM during early evolution mimics ultra-relativistic radiation whereas at late times, it behaves as dust, quintessence or even the cosmological constant depending on the value of λ. The effective matter acts as a stiff fluid irrespective of the matter content and of the f(R, T) terms. The model is shear free at late times but remains anisotropic throughout the evolution. In the absence of the f(R, T) terms, SQM accelerates the universe. In the specific case when SQM vanishes at late times, the effect of f(R, T) is to accelerate the universe. The model admits the possibility that SQM could be an alternative to dark energy.

We obtain exact solutions to the field equations for 5 dimensional LRS Bianchi type-I spacetime in $f(R,T)$ theory of gravity where specifically the following three cases are considered: (i) $f(R,T)=\mu(R+T)$, (ii) $f(R,T)=R \mu + R T \mu^2$ and (iii) $f(R,T)=R+\mu R^2+\mu T$ where $R$ and $T$ respectively the Ricci scalar and trace of the energy-momentum tensor. It is found that the equation of state (EOS) parameter $w$ is governed by the parameter $\mu$ involved in the $f(R,T)$ expressions. We fine-tune the parameter $\mu$ to obtain effect of phantom energy in the model, however we also restrict this parameter to obtain a stable model of the universe. It is noted that the model isotropizes at finite cosmic time.

In this work, we study the existence of strange star in the background of f(T,T) gravity in the Einstein spacetime geometry, where T is the torsion tensor and T is the trace of the energy-momentum tensor. The equations of motion are derived for anisotropic pressure within the spherically symmetric strange star. We explore the physical features like energy conditions, mass-radius relations, modified TOV equations, principal of causality, adiabatic index, redshift and stability analysis of our model. These features are realistic and appealing to further investigation of properties of compact objects in f(T,T) gravity as well as their observational signatures.

Many quantum dot light-emitting diodes (QLEDs) utilize ZnO nanoparticles (NPs) as an electron injection layer (EIL). However, the use of ZnO NP ETL material often results in charge imbalance within the quantum dot (QD) emitting layer (EML) and exciton quenching at the interface of QD EML and ZnO NP EIL. To overcome these challenges, we introduced an Arginine (Arg) interlayer (IL) onto the ZnO NP EIL. The Arg IL elevated the work function of ZnO NPs, thereby suppressing electron injection into the QD, leading to improved charge balance within the QDs, Additionally, the inherent insulating nature of the Arg IL prevented direct contact between QDs and ZnO NPs, reducing exciton quenching and consequently improving device efficiency. The inverted QLED (IQLED) utilizing a 20-nm-thick Arg IL on ZnO NP EIL exhibited a 2.22-fold increase in current efficiency and a 2.28-fold increase in EQE and compared to an IQLED without an IL. Likewise, the IQLED with a 20-nm-thick Arg IL on ZnO NP EIL demonstrated a 1.34-fold improvement in current efficiency and a 1.36-fold increase in EQE compared to IQLED with a 5-nm-thick PEI IL on ZnO NPs.

Keywords: Marine Coasts; Protected Areas; Defense and Conservation; Asbestos Cement Materials; Wastes; Contamination; Human Health Risk; Medical Geology.

A millimeter-wave microstrip leaky-wave antenna array based on the substrate-integrated waveguide (SIW) and the complementary split-ring resonator (CSRR) is proposed in this paper. The slow wave characteristics of the SIW are enhanced by etching two rows of symmetrical CSRR-type slots on the surface of the SIW layer. The magnetic coupling between the CSRR-SIW layer and equally spaced circular patches array on the upper layer realizes the radiation of electromagnetic energy. In the 23~30 GHz (relative bandwidth 26.4%) operating frequency band, the horizontal polarization radiation beam scanning from -62° to -2° is realized, with a peak gain of 9.6~11.7 dBi, and the cross-polarization ratio is more than 43.8 dB.

Petrosamine (1) – a colored pyridoacridine alkaloid from the Belizean sponge, Petrosia sp. that is also a potent inhibitor of acetylcholine esterase (AChE) – was investigated by spectroscopic and computational methods. Analysis of the petrosamine free energy landscapes, pKa and tautomerism revealed an accurate electronic depiction of the molecular structure of 1 as the di-keto form, with net charge of q = +1, rather than a dication (q = +2) under ambient conditions of isolation-purification. The pronounced solvatochromism (UV-vis) reported for 1, and related analogs, was investigated in detail and is best explained by charge delocalization and stabilization of the ground state (HOMO) of 1 rather than an equilibrium of competing tautomers. Refinement of the molecular structure of 1 by QM methods complements published computational docking studies to define the contact points in the enzyme active site that may improve design of new AChE inhibitors based on the pyridoacridine alkaloid molecular skeleton.

Small-cell lung cancer (SCLC) is a cancer with poor prognosis. For relapsed extensive-stage (ES) SCLC, second-line treatment options are scarce. Topotecan was the only approved treatment in this setting until 2020. Since topotecan induces significant toxicities, alternative off-label regimens are being used. This study evaluated real-world efficacy and safety of Paclitaxel Gemcitabine chemotherapy in patients with relapsed ES-SCLC. We retrospectively reviewed data from all consecutive patients with relapsed ES-SCLC who received Paclitaxel Gemcitabine chemotherapy from september 2008 to january 2022 in two centers. Patient characteristics (n=188) were: PS≥2: 24.5%; brain metastasis: 42%; platinum-sensitive disease: 41%. Patients received Paclitaxel Gemcitabine as second- (77%) third (18%) or fourth (6%) line of therapy. Median progression-free and overall survival were 2.1 (95CI 1.8–2.4) and 3.8 (95CI 3.3–4.8) months in the overall population, respectively, with 17% response rate (RR) and 28% disease-control rate. PS, history of brain radiation, platinum-sensitive disease, liver, and adrenal gland metastasis were associated with longer survival in univariate analysis. PS was the only prognostic factor in multivariate analysis, with 21% RR and 4.1 months median DOR in PS 0-1 patients. Paclitaxel Gemcitabine chemotherapy may represent a treatment option in PS0-1 relapsed SCLC.

French Guiana, located in the Guiana Shield, is a natural reservoir for many zoonotic pathogens that are of considerable medical or veterinary importance. Until now, there are few data available on the description of parasites circulating in this area, especially on protozoan belonging to the phy-lum Apicomplexa; conversely, the neighbouring countries describe a high parasitic prevalence in animals and humans. Epidemiological surveillance is necessary, as new potentially virulent strains may emerge from these forest ecosystems, such as Amazonian toxoplasmosis. However, there is no standard tool for detecting protozoa in wildlife. In this study, we developed Meat-Borne-Parasite, a high-throughput meta-barcoding workflow for detecting Apicomplexa based on Oxford Nanopore Technologies sequencing platform using the 18S gene of fourteen Apicomplexa-positive samples collected in French Guiana. Sequencing reads were then analysed with MetONTIIME pipeline. Thanks to a scoring rule, we were able to classify as Apicom-plexa-positive 10 samples out of 14 and reveal the presence of co-carriages. The same samples were also sequenced with Illumina platform, for validation purposes. On samples identified as Apicomplexa-positive by both platforms, a strong positive correlation at up to genus level was reported. Overall, the presented workflow represents a reliable method for Apicomplexa detec-tion, which may pave the way for more comprehensive biomonitoring of zoonotic pathogens.

Background and Objectives:: Hip osteoarthritis is the main cause physical disability, also has a serious impact on the efficiency and independence of older people. The aim of the study was to analyze the relationship between hip osteoarthritis and the risk of sarcopenia. Our main hypothesis was whether the risk of sarcopenia, as measured by the SARC F questionnaire , is related to the physical fitness of older people with hip osteoarthritis. Materials and Methods: The study was conducted with the participation of 177 people of aged 65 or more, diagnosed hip osteoarthritis. The subjects were assessed using the SARC F questionnaire, the Short Physical Performance Battery (SPPB) and Timed Up and Go (TUG) test. The subjects were divided into two groups depending on the result they obtained in the SARC F questionnaire (group 1- SARC F &lt;4, group 2 - SARC F ≥ 4). Results: There was a significant correlation between the results in the SARC F and the results of the TUG (p&lt;0.001) and the SPPB test, both the SPPB total score (p&lt;0.001)and its elements: SBBP chair stand test (p&lt;0.001), SPPB balance test (p&lt;0.001), SPPB gait speed test (p&lt;0.001). Logistic regression of the SPPB and TUG predictors showed that in SARC F more than 4 predicted worse SPPB and TUG outcomes. In the SARC group, F above 4 increases the odds of poorer scores in SPPB OR=1.097; CI 95% 1.053-1.146 and TUG, OR=1.096; CI 95% 1.104-1.266. Conclusion: The study showed that the results obtained in the SARC F questionnaire correlate with the possibilities of physical functioning in patients with hip osteoarthritis SARC F is an inexpensive method that can be used to assess the risk of sarcopenia. Healthcare professionals, especially in primary care, should consider assessing the risk of sarcopenia especially in people with hip osteoarthritis.

In this study, the degradable superhydrophobic Mg/P/Z/F/H (magnesi-um/poly(-caprolactone)/zinc oxide/1H,1H,2H,2H-perfluorodecyltriethoxysilane (PFDTES)/ heating process) composite materials were prepared through one-step method for enhancing the corrosion resistance of AZ91D magnesium alloys. Electrochemical measurements showed that Mg/P/Z/F/H materials significantly improved the corrosion resistance of magnesium alloys in 3.5 wt.% NaCl. The self-cleaning, adhesion and stability tests suggested that Mg/P/Z/F/H composite materials had well self-cleaning properties, good adhesion strength and stability in wet atmosphere.