We aimed to investigate the relationship between membrane material and development of membrane fouling in a membrane bioreactor (MBR) using membranes with different pore sizes and hydrophilicities. Batch filtration tests were performed using submerged single hollow fiber membrane ultrafiltration (UF) modules with different polymeric membrane materials including cellulose acetate (CA), polyethersulfone (PES), and polyvinylidene fluoride (PVDF) with activated sludge taken from a municipal wastewater treatment plant. The three UF hollow fiber membranes were prepared by a non-solvent-induced phase separation method and had similar water permeabilities and pore sizes. The results revealed that transmembrane pressure (TMP) increased more sharply for the hydrophobic PVDF membrane than for the hydrophilic CA membrane in batch filtration tests, even when membranes with similar permeabilities and pore sizes were used. PVDF hollow fiber membranes with smaller pores had greater fouling propensity than those with larger pores. In contrast, CA hollow fiber membranes showed good mitigation of membrane fouling regardless of pore size. The results obtained in this study suggest that the surface hydrophilicity and pore size of UF membranes clearly affect the fouling properties in MBR operation when using activated sludge.

Lactoperoxidase (LP), which is a high-value minor whey protein, has recently drawn extensive attention from research scientists and industry due to its multi-function and potential therapeutic applications. In this study, the separation and optimization of two similar-sized proteins, LP and lactoferrin (LF) were investigated using strong cation exchange column chromatography. Optimization was started with central composite design based experiments to characterize the importance of different decision variables. The three variables used in the optimization were flow rate, length of gradient and final salt concentration in the linear elution gradient step. The obtained empiric functional model represented the effect of the significant factors on the yield as the objective function. Afterwards, the calibrated mechanistic model was employed to predict accurate optimal set of variables. The optimal operating points were found and the results were compared with validation experiments. Predictions respecting yield confirmed a very good agreement with experimental results while keeping purity, a product quality characteristic, equal or above to a predefined value.

As marine traffic is contributing to pollution and mostly have predictable route with repetitive load profiles, to reduce their impact on environment, hybrid system with proton exchange membrane fuel cells (PEMFC-s) and battery pack, is promising replacement. For this purpose, the numerical model of repowered existing vessel that have two diesel engines with 300 kWe is developed. The goal of this paper is to develop numerical model which analyzes and determine equivalent hybrid ship propulsion system for known traveling route. The developed numerical model consists of an interconnected system with PEMFC stack and battery pack as power sources. Numerical model is developed and optimized to meet minimal required power demand for successful route demand, which has variable loads and daily sails six-time same voyage- in total 54 nautical miles. The results have shown that equivalent hybrid power system consists of 300 kWe PEMFC stack and battery pack with 424 kWh battery and state of charge varying between 20 and 87%. To power this new hybrid power system, hydrogen tank of 7200 l holding 284.7 kg at pressure of 700 bar is needed, compared to previous system that spend 1524 kg of diesel and generate 4886 kg of CO2.

The application of diffusion dialysis using various types of ion-exchange membranes for the separation of sulfuric acid and nickel sulfate has been evaluated. The process of dialysis separation of a real waste solution from an electroplating facility containing 252.3 g/L of sulfuric acid, 20.9 g/L of nickel ions and small amounts of zinc, iron, copper ions, etc. has been studied. Heterogeneous cation-exchange membrane containing sulfo groups and heterogeneous anion-exchange membranes with different thicknesses (from 145 μm to 550 μm) and types of fixed groups (4 samples with quaternary amino groups and 1 sample with secondary and tertiary amino groups) are used. The diffusion fluxes of sulfuric acid, nickel sulfate, and the total and osmotic fluxes of the solvent are determined. The use of a cation-exchange membrane does not allow separation of the components, since the fluxes of both components are low and comparable in magnitude. The use of anion-exchange membranes makes it possible to efficiently separate sulfuric acid and nickel sulfate. At the same time, the thin dialysis membrane turns out to be the most effective, as well as the membranes with quaternary amino groups, and the membrane with secondary and tertiary amino groups proved to be the least effective.

In this study, the hybrid biological ion exchange (BIEX) resin and gravity-driven membrane (GDM) process was employed for the treatment of coloured and turbid river water. The primary objective was to investigate the impact of both physical and chemical cleaning methods on ceramic and polymeric membranes in terms of stabilised flux, flux recovery after physical/chemical cleaning, and permeate quality. To address these objectives, two types of MF and UF membranes were utilised (M1 = polymeric MF, M2 = polymeric UF, M3 = ceramic UF, and M4 = lab-made ceramic MF).Throughout extended operation, the resin functioned initially in the primary ion exchange (IEX) region (NOM displacement with pre-charged chloride) and progressed to a secondary IEX stage (NOM displacement with bicarbonate and sulphate), while membrane flux remained stable. Subsequently, physical cleaning involved air/water backwash with two different flows and pressures, and chemical cleaning utilised NaOH at concentrations of 20 and 40 mM, as well as NaOCl at concentrations of 250 and 500 mg Cl2/L. These processes were carried out to assess flux recovery and identify fouling reversibility. The results indicated an endpoint of 1,728 bed volumes (BV) for the primary IEX region, while the secondary IEX continued up to 6,528 BV. At the end of the operation, DOC and UVA254 removal in the effluent of the BIEX columns were 68% and 81%, respectively, compared to influent water. This was followed by 30% and 57% DOC and UVA254 removal by M4 (ceramic MF). The stabilised flux remained approximately 3.8 – 5.2 LMH both before and after the cleaning process, suggesting that membrane materials do not play a pivotal role. The mean stabilised flux of polymeric membranes increased after cleaning, whereas that of ceramics decreased. Enhanced air–water backwash flow and pressure resulted in increased removal of hydraulic reversible fouling, which was identified as the dominant fouling type. Ceramic membranes exhibited higher removal of reversible hydraulic fouling than polymeric membranes. Chemical cleaning had a low impact on flux recovery; therefore, we recommend solely employing physical cleaning.

Water electrolysis provides efficient and cost-effective production of hydrogen from renewable energy. Currently, the oxidation half-cell reaction relies on noble-metal catalysts, impeding widespread application. In order to adopt water electrolyzers as the main hydrogen production systems, it is critical to develop inexpensive and earth-abundant catalysts. This review discusses the proton exchange membrane (PEM) water electrolysis (WE) and the progress in replacing the noble-metal catalysts with earth-abundant ones. Researchers within this field are aiming to improve the efficiency and stability of earth-abundant catalysts (EACs), as well as to discover new ones. The latter is particularly important for the oxygen evolution reaction (OER) under acidic media, where the only stable and efficient catalysts are noble-metal oxides, such as IrO_x and RuO_x. On the other hand, there is significant progress on EACs for the hydrogen evolution reaction (HER) in acidic conditions, but how many of these EACs have been used in PEM WEs and tested under realistic conditions? What is the current status on the development of EACs for the OER? These are the two main questions this review addresses.

The generation and maintenance of membrane potential is a fundamental part of Membrane Pump Theory. One of the key points of this hypothesis is based on a natural or facilitated molecular diffusion through several types of ion channels and pumps like the Na/K ATPase. Following the principles of chemistry, electrostatics and geometry, it becomes clear that ion channels cannot function in this way. The ions channels cannot by their location have both a filter function and be ion concentrators, and the Na/K pump by its position in the membrane and by the proposed assumptions is not able to perform its regulatory function. The current model must absolutely be revised according to the current state of our knowledge and allow an advance in the understanding of the phenomena opening new research perspectives.

Various methods including electrochemical purification, chemical precipitation, solvent extraction, and ion-exchange resins, have maturely been used for removal of copper from nickel anolyte. Interestingly, these approaches of copper removal from nickel anolyte by precipitation are well used as the primary industrial method in nickel production again. However, these methods suffer from several severe drawbacks in industrial practices. One is that a small amount of nickel precipitates with copper in slags，resulting in slag treatment difficulties. Second, this process requires an extremely high activity of the sulfide-based copper removal agents which results in high production costs; the short storage period of the copper removal agent is another drawback of this method. These have been the key challenges in the smelting process of nickel. Herein, we present a comprehensive review of the nickel removal methods used for nickel anolyte purification, electrochemical purification, chemical precipitation, solvent extraction, and ionexchange resins. The advantages and feasibilities of each technique in industrial applications are also explored and analyzed. Finally, we demonstrate that ion-exchange resin-based extraction method can pave a new path for metallurgical research on nickel.

The research presented in this article is based on a strategic approach to a rural area in the mountainous region of Romania and is underwritten by specialists in the economy of mountainous regions in order to elaborate relevant solutions to complex problems relating to sustainable development. In essence, the research underlines and promotes the particularities of performing research for the identification and valuation of endogenous resources, that is, creating relevant strategic options for the durable development of the mountainous region, centered on the renewal of economic activities related to the existent endogenous resources, by using methods, work techniques, and instruments of strategic analysis. These factors are subordinate to the process of harmonization to the requirements of community development and environmental protection according to the new strategy for the development of the European Union 2020 (European Green Pact). This pact also emphasizes the necessity of involving the different factor categories of local accountability, promotion, activation, and the development of specific economic activities of different local contexts of sustainability. The research methodology used involves a case study whose complexity necessitated the use of quality and quantity research methods in order to underline specific elements of the rural area in the Romanian mountainous region. Specifically, we used a strategic diagnosis of the Romanian mountainous region using the PESTEL and SWOT models. In order to have relevant strategic options available, the continuity of research was achieved through the use of SOR analysis, creating a problem tree and an objectives tree.

The separation of Li+ and [Bmim]+(1-Butyl-3-methylimidazolium) by electrically driven membrane technology was studied. The effects of the types and modification processes of cation exchange membranes, current density, total cation concentration, temperature, and anion types on separation efficiency were investigated. The results indicated that it is feasible to achieve efficient separation of Li+ and [Bmim]+ using the selectivity of cation exchange membranes under electric field. Membrane CMX and the modified membrane A and B which obtained from the CMX showed obvious selective of Li+ from [Bmim]+. When the current density is 5 mA/cm2 and the feed concentrations of Li+ and [Bmim]+ are 0.3 mol/L and 0.2 mol/L, the selective transport coefficient of the modified membrane B can reach 6.2 in the first 120 minutes of the process. Reducing current density and increasing total cation concentration can improve separation efficiency. Lowering the temperature can improve the separation effect, but improvement is not obviously. Changing the anion of the feed from chloride ion to acetate has no effect on the separation.

Infrared spectroscopy is an effective method for the determination of compositions and concentrations of liquids, with advantages of fast response, no-sampling, flexible in use and is able for on-line monitoring. However, for trace substances in drinking water, such as nitrates and heavy metals, infrared spectroscopy is not sensitive enough for the quantitative and qualitative measurement. In this study, we improved the sensitivity of infrared spectroscopy for nitrite determination by developing an ion-exchange-enhanced diffuse reflectance spectroscopy, which consist of an accessory based on ion-exchange resin for enrichment and a FTIR spectrometer for measurement. Using this method, the limit of detection for nitrate is 1.7 mg/L, which is enough for drinking water sensing. We also verified the quantitative measurement ability of the method. Furthermore, the limit of detection and quantitative measuring range could be adjusted by changing the mass of resin and adsorption time. This study demonstrated the method can be used to detect trace nitrites in drinking water, can be applied in the field, and is sensitive, rapid, and inexpensive with a wide dynamic range.

Exergy analysis evaluates the efficiency of system components by quantifying the rate of entropy generation. In general, the exergy destruction rate or irreversibility rate was directly obtained through the exergy-balance equation. However, this method cannot determine the origin of the component's entropy generation rate, which is a very important factor in system design and improvement. In this study, a thorough energy, exergy thermoeconomic analysis of a proton exchange membrane fuel cell (PEMFC) was performed, providing the heat transfer rate, entropy generation rate and cost loss rate of each component. The irreversibility rate of each component is obtained by the Gouy-Stodolar theorem. Detailed and extensive exergy and thermoeconomic analyses of PEMFC system have determined that water cooling units experience the greatest heat transfer among the components in the studied PEMFC system, resulting in the greatest irreversibility and thus the greatest monetary flow loss.

PEM fuel cell is a technology successfully used in the production of energy from hydrogen, allowing the use of hydrogen as an energy vector. It is scalable for stationary and mobile applications. However, the technology demands more research. An important research topic is fault diagnosis and condition monitoring to improve the life and the efficiency and to reduce the operation costs of PEMFC devices. Consequently, there is a need of physical models that let deep analysis. These models must be accurate enough to represent the PEMFC behavior and to allow the identification of different internal signals of a PEM fuel cell. This work presents a PEM fuel cell model that uses the output temperature in a closed loop, so it can represent the thermal and the electrical behavior. The model is used to represent a NEXA Ballard 1.2 kW; therefore it is necessary to fit the coefficients to represent the real behavior. Five optimization algorithms were tested to fit the model, three of them were taken from literature and two were proposed. Finally, the model with the parameters identified was validated with real.

Ion channels are integral membrane proteins that facilitate the movement of ions across cell membranes, playing a key role in a range of biological processes. The high cost and time required for wet lab experiments to characterize ion channels has spurred the development of computational methods for this purpose. In our previous work, we demonstrated the effectiveness of protein language models for ion channel prediction, using a logistic regression classifier to distinguish ion channels from non-ion channels (TooT-BERT-C) and transporters from non-transporters (TooT-BERT-T). In this study, we build upon this approach by using a combination of classical machine learning classifiers and a Convolutional Neural Network (CNN) with fine-tuned representations from ProtBERT, ProtBERT-BFD, and MembraneBERT to discriminate ion channels from non-ion channels. The results of our experiments demonstrate that TooT-BERT-CNN-C, a combination of the representations from ProtBERT-BFD and a CNN, outperforms existing state-of-the-art methods for predicting ion channels, with a Matthews Correlation Coefficient (MCC) of 0.86 and an accuracy of 98.35% on an independent test set.

Anion exchange membrane (AEM) electrolysis is hampered by two main issues: stability and performance. Focusing on the latter, this work demonstrates a highly active NiMo cathode for hydrogen evolution in AEM electrolysis. We demonstrate an electrolyzer performance of 1 A cm⁻² at 1.9 V (total cell voltage) with a NiMo loading of 5 mg cm⁻² and an iridium black anode in 1 M KOH at 50 °C, that may be compared to 1.8 V for a similar cell with Pt at the cathode. The catalysts developed here will be significant in supporting the pursuit of cheap and environmentally friendly hydrogen fuel.

Proton exchange membrane (PEM) fuel cells have emerged as a viable alternative energy production source for stationary and transportation applications. Reliable and sustainable fuel cell operation requires effective water management. Membrane water content can vary along the stack during transients which can lead to losses in fuel cell performance. To control these variations a model that predicts the internal humidity dynamics of the stack is needed. In this study, a control-oriented model for predicting membrane water content variation was developed and implemented in MATLAB/Simulink. A lumped parameter model was initially developed and then further discretized into smaller control volumes to track humidity distribution along the stack. To validate the model’s predictions, the predicted results were compared to computer simulation results from GT-Suite. The root mean square error (RMSE) between the model’s prediction and GT-Suite’s simulation results was found to be within 1.5 membrane water content for all cases, demonstrating the model’s capability to capture the variation of membrane water content along the stack. The developed model will be useful for real-time control of membrane water content variation in PEM fuel cells.

An ion exchange dialysis (IED) is used in the recovery of aluminium from residue. In this papers, the face-centered central composite design (FC-CCD) of the response surface methodology (RSM) and desirability approach is used for experimental design, modelling and process optimization of a counter flow IED system. The feed concentration, feed flowrate, sweep flowrate and sweep concentration are selected as the process variables, with the Al-transport across a Nafion 117 membrane as the target response. A total of 30 experimental runs were conducted with 6 center points. The response obtained was analysed by analysis of variance (ANOVA) and fitted to a second-order polynomial model using multiple regression analysis. The actual R2 and standard deviation of the model are 0.9548 and 0.2932 respectively. The influences of significant variables are plotted on 3D surface and contour plots. The designed variables were numerically optimized by applying the desirability function to achieve the maximum Al-transport. The optimised condition values were found to be feed concentration (1600 ppm), feed flowrate (61.76%), sweep flowrate (37.50%) and sweep concentration (0.75 N) for the 80% target response at 32hrs. Overall, the model can be used to effectively predict Al-recovery using the designed system

The vagina is an essential component of the female reproductive system and is responsible for providing female sexual satisfaction. Vaginal smooth muscle contraction plays a crucial role in various physiological processes, including sexual arousal, childbirth, and urinary continence. In pathophysiological conditions such as pelvic floor disorders, aberrations in vaginal smooth muscle function can lead to urinary incontinence and pelvic organ prolapse. A set of cellular and sub-cellular physiological mechanisms regulates the contractile properties of the vaginal smooth muscle cells. Calcium influx is a crucial determinant of smooth muscle contraction, facilitated through voltage-dependent calcium channels and calcium release from intracellular stores. Comprehensive reviews on smooth muscle biophysics are relatively scarce within the scientific literature, likely due to the complexity and specialized nature of the topic. The objective of this review is to provide a comprehensive description of alterations in the cellular physiology of vaginal smooth muscle contraction. The benefit associated with this particular approach is that conducting a comprehensive examination of the cellular mechanisms underlying contractile activation will enable the creation of more targeted therapeutic agents to control vaginal contraction disorders.

The theory of heavy ion double charge exchange (DCE) reactions proceeding by effective rank–2 isotensor interactions is presented. Virtual pion–nucleon charge exchange interactions are investigated as the source for induced isotensor interactions, giving rise to the Majorana DCE (MDCE) reaction mechanism. MDCE is of a generic character, proceeding through pairs of complementary (π±,π∓) reactions in the projectile and target nucleus. The dynamics of the elementary processes is discussed where the excitation of pion–nucleon resonances are of central importance. Investigations of initial and final state ion–ion interactions show that these effects are acting as vertex renormalizations. In closure approximation, well justified by the finite pion mass, the second order transition matrix elements reduce to pion potentials and effective two–body isotensor DCE interactions, giving rise also to two–body correlations in either of the participating nuclei. Connections to neutrinoless Majorana double beta decay (MDBD) are elucidated at various levels of dynamics, from the underlying fundamental electro–weak and QCD scales to the physical scales of nuclear MDBD and MDCE physics. It is pointed out that heavy ion MDCE reactions may also proceed by competing electro–weak charge exchange processes, leading to lepton MDCE by electrons, positrons, and neutrinos.

The two-phase flow of water and reactive gas in the channel of proton exchange membrane fuel cell (PEMFC) plays an important role in high-quality water management. In this study, the removal effect of 3D wave channel and 2D straight channel for liquid water was studied by volume of fluid method. The dynamic behavior of droplet emerge from the gas diffusion layer (GDL) into the channel under the influence of gas flow was investigated. The effects of droplet growth, deformation, detachment, force, pore size on water critical behavior and water content in the channel are discussed. The results show that the 3D wave channel is superior to the removal of liquid water than the 2D straight channel. The increase of velocity is conducive to the discharge liquid water. While infinite increase of velocity will cause more parasitic power loss. The larger pore size of GDL is not advantageous to the performance of PEMFC, but the appropriate increase of pore size is conducive to the discharge of liquid water. The basic knowledge obtained in this study will help to deepen the understanding of droplet dynamics in PEMFC gas channels, and help to optimize the design and working conditions of these channels.

The present work investigates primarily the morphology evolution of the body-centered-cubic (BCC)/B2 phases in AlxNiCoFeCr high-entropy alloys (HEAs) with increasing Al content, which has been neglected so far. There exist two types of microscopic morphologies of BCC and B2 phases in this HEA series: one is the weave-like morphology induced by the spinodal decomposition, and the other is the microstructure of a spherical disordered BCC precipitation on the ordered B2 matrix that appears in HEAs with a much higher Al content. The shape of coherent precipitates is found to be closely related to the lattice misfit between BCC and B2 phases, which is sensitive to Al. The mechanical properties, including the compressive yielding strength and microhardness of the AlxNiCoFeCr HEAs, are also discussed in light of the concept of the valence electron concentration (VEC).

The role of initial state (ISI) and final state (FSI) ion–ion interactions in heavy ion double charge exchange (DCE) reactions A(Z,N)→A(Z±2,N∓2) are studied in the context of double single charge exchange (DSCE) reactions given by sequential actions of the isovector nucleon–nucleon (NN) T–matrix. The second order DSCE reaction amplitude is investigated in momentum representation in a formulation, focused on the extraction of nuclear matrix elements under the conditions of strong initial state (ISI) and final state (FSI) interactions. In closure approximation and using the momentum representation, the reaction amplitude is finally separated into ISI/FSI distortion coefficients and reaction kernels and nuclear matrix elements. The ISI/FSI reaction kernels emerge as the result of the repeated scattering on the avoided volume, introduced by the imaginary parts of the ion–ion optical potential and acting as sinks for the quantal probability current. The closure approximation allows derive a set of induced effective two–body isotensor interactions, given by products of spin–scalar, spin–vector central and rank–2 spin–tensor interactions. The intermediate propagator plays a key role in establishing correlation between the DCE transitions in the projectile and target nucleus. The presented approach emphasizes the special features of DSCE reaction dynamics as proceeding like a system of two coupled isospin dipoles whose strengths are determined by the momentum-space form factors of the NN isovector interaction. The properties of the DSCE interaction form factors are investigated and the approach is applied to data.

The processability of conductive polymers such as polyaniline (PANI) still poses a challenge due to their properties. The use of stabilizers, compatible and able to interact with PANI, to obtain dispersible and stable colloids is described in this work. To this aim, potato starch has been used as a steric stabilizer for the preparation of polyaniline (emeraldine salt, ES)/starch biocomposites, by exploiting oxidative polymerization of aniline in aqueous solutions containing different ratios of aniline and starch (% w/w). The polyaniline/starch biocomposites were subjected to structural and spectroscopic analyses, thermal analysis, morphological analysis and electrochemical analysis. The samples were then tested for their dispersibility/solubility in various organic solvents. The results showed the formation of PANI/starch biocomposites with an overall smaller size than starch particles, with improved aqueous dispersion and solubility in organic solvents. Although X-ray diffraction and differential scanning calorimetry analyses indicated a loss of crystallinity in the biocomposites, the cyclic voltammetry tests showed that all PANI ES/starch biocomposites display improved redox exchange properties.

A new trend in cow's milk has emerged in the market called type A1 and A2 milk. These products have piqued the interest of both consumers and researchers. Recent studies suggest that A2 milk may have potential health benefits, which is why researchers are investigating this product further. It is interesting to note that the A1 and A2 milk types have area-specific characteristics compared to breed-specific characteristics. Extensive research has focused on milk derivatives obtained from cow’s milk, primarily through in vitro and animal studies. However, few clinical studies have been conducted in humans, and the results have been unsatisfactory. New molecular techniques for identifying A1 and A2 milk may help researchers to develop new studies that can clarify certain controversies surrounding A1 milk. It is essential to exercise extreme caution when interpreting the updated literature. It has the potential to spread panic worldwide and have negative economic implications. Therefore, this study aims to investigate the new aspects of A1 and A2 milk in different research areas and clarify some aspects regarding these two types of milk.

A model is proposed that describes the transfer of ions and the process of water dissociation in a system with a bipolar membrane and adjacent diffusion layers. The model considers the transfer of four types of ions: the cation and anion of salt and the products of water dissociation – hydrogen and hydroxyl ions. To describe the process of water dissociation, a model for accelerating the dissociation reaction with the participation of ionogenic groups of the membrane is adopted. The boundary value problem is solved numerically using COMSOL® Multiphysics 5.5 software. An analysis of the results of a numerical experiment shows that, at least in a symmetric electromembrane system, there is a kinetic limitation of the water dissociation process, apparently associated with the occurrence of water recombination reaction at the of the bipolar region. An interpretation of the entropy factor (β) is given as a characteristic length which shows the possibility of an ion that appeared as a result of the water dissociation reaction to be removed from the reaction zone without participating in recombination reactions.

Ion Transport Membrane (ITM) is a well-developed technology for producing O₂ by separating air in its membrane. To decrease energy loss in air separation unit and to increase the overall efficiency of a power generation unit ITM is added with the gasification unit in this model. Ceramic materials are generally used to make ion transport membrane that produces oxygen by conducting oxygen ions at specified temperature. Potential advantages can be gained by integrating ITM technology with power generation units as 99% pure oxygen is produced from ITM. A salient comparison between ITM air separator combined with IGCC and cryogenic air separator combined with IGCC is done in this paper where the total power generation cycle remains same for both cases excluding the air separation units (ITM and cryogenic). Using ITM air separator is more beneficial compared to cryogenic air separation as ITM technology helps to improve IGCC overall efficiency and also reduces plant auxiliaries than that of power generation systems integrated with cryogenic.

In a recent article, Smoom et al. identified an important amino acid variation in the helicase RTEL1 of the Algerian mouse (Mus spretus). Since the latter has telomeres five times shorter than the laboratory mouse (belonging to the Mus musculus species), they introduced this variation in laboratory mice, in order to obtain an engineered strain with human-length telomeres. Succeeding in doing this, they established the “Telomouse” strain. Here I demonstrate that, in reality, Mus spretus does not show this variation: the key amino acid is conserved in all rodent species, which all have human-length telomeres (including wild Mus musculus species). This finding in no way compromises the value of the research of Smoom et al. and the utility of the Telomouse strain. Rather, it raises the question of how the telomere length of Mus musculus (as a species) should be considered and the important consequences it has on studies on inter-species comparison.

Rare earth elements (REEs) and Sc are concentrated in aluminum production byproducts. The novel REEs recovery approach, which involves leaching by acid at a pH > 3 in the presence of MgSO4, results in the formation of a pregnant leach solution (PLS) with a low concentration of iron (Fe) and titanium (Ti) and a large quantity of valuable elements. The ion exchange method was acknowledged as the most favorable method used to separate the REEs from PLS. This work studies the application of chelating resin Puromet МТS9580 in the sorption recovery of Sc from sulfate solutions. To analyze the static Sc sorption data, Langmuir, Freundlich, and Temkin isotherm models were used. The Langmuir isotherm model was the best fitted to the experimental data, with a coefficient of determination (R2) of 0.983. The dynamic adsorption experiment was conducted using a PLS and a simulate solution without contaminants. Adsorption of Sc from the simulate solution was better fitted to the Thomas model with a Sc capacity greater than 7 mg mL–1. Because Ti had a gradual decrease in C/C0, which the Thomas model was unable to simulate, the modified dose-response (MDR) model fitted better with PLS. The NaHCO3 solution (200 g L–1) effectively desorbed Sc (>98 %) from simulated and PLS solutions after 1.5 h of stirring in a batch mode.

As Li-ion batteries use is spreading, incidents in large energy storage systems (stationary storage containers, …) or in large-scale cell and battery storages (warehouse, recyclers, …), often leading to fire, are occurring on regular basis. Water remains one of the most efficient fire extinguishing agents for tackling those battery incidents and large quantities are usually necessary. Since bat-teries contains various potentially harmful components (metals and their oxides or salts, sol-vents…) and that thermal runway induced battery incidents are accompanied with complex and potentially multistage fume emissions (containing both gas and particles) the potential impact of fire run-off water on the environment should be considered and assessed carefully. The tests presented in this paper focus on the analysis of the composition of run-off waters used to spray NMC Li-ion modules under thermal runaway. It highlights that waters used for fire-fighting are susceptible to contain many metals, including Ni, Mn, Co, Li and Al mixed with other carbonaceous species (soot, tarballs) and sometimes undecomposed solvents used in the elec-trolyte. Extra-polation of pollutant concentrations compared with PNEC values showed that, for large scale incidents, run-off water could be potentially hazardous to the environment.

Innovative tissue engineering biomimetic hydrogels based on hydrophilic polymers have been investigated for their physical and mechanical properties. 5% to 25% by volume loading PHEMA-nanosilica glassy hybrid samples were equilibrated at 37°C in aqueous physiological isotonic and hypotonic saline solutions (0.15 and 0.05 M NaCl) simulating two limiting possible compositions of physiological extracellular fluids. The glassy and hydrated hybrid materials were characterized both for dynamo-mechanical properties and equilibrium absorptions in the two physiological-like aqueous solutions. Mechanical and the morphological modifications occurring in the samples have been described. The 5% volume nanosilica loading hybrid nanocomposite composition showed mechanical characteristics in the dry and hydrated states that were comparable to those of cortical bone and articular cartilage, respectively, and then chosen for further sorption kinetics characterization. Sorption and swelling kinetics were monitored up to equilibrium. Changes in water activities and osmotic pressures in the water-hybrid systems equilibrated at the two limiting solute molarities of the physiological solutions have been related to the observed anomalous sorption modes using the Flory-Huggins interaction parameter approach. The bulk modulus of the dry and glassy PHEMA-5% nanosilica hybrid at 37°C has been observed to be comparable with the values of the osmotic pressures generated from the sorption of isotonic and hypotonic solutions. The anomalous sorption modes and swelling rates are coherent with the difference between osmotic swelling pressures and hybrid glassy nano-composite bulk modulus: the lower the differences the higher the swelling rate and equilibrium solution uptakes. Bone tissue engineering benefits of use of tuneable biomimetic scaffold biomaterials that can be “designed” to act as biocompatible and biomechanically active hybrid interfaces are discussed.

The concept of a Social License to Operate (SLO) has become increasingly important in the sustainability literature in recent years. Having its origins in the business discourse of the mining industry with respect to limiting opposition to mining projects, the notion of a social contract above and beyond legal requirements has since become applied across a number of different industries. Despite the concepts adoption confusion exists over the practices and outcomes of SLO, and particularly the nature of engagement. Given this situation it is surprising that not more attention to the role of marketing, and social marketing in particular, in operationalizing the concept. The paper discusses the potential of social marketing to contribute to SLO. Economic, political and social relations are complex in SLO and exchange is intricate in such relational environments. A community-based social marketing orientation is proposed as a means to improve exchange relations and enhance engagement. Seven models of SLO related social marketing models are discussed with community-based social marketing and adaptive co-marketing models being regarded as the most positive for the achievement of an SLO. Potential barriers to adoption of these approaches are noted.

Understanding the ionic channel network of proton exchange membranes, which dictate fuel cell performance, is crucial when developing proton exchange membrane fuel cells. However, itis difficult to characterize due to complicated nano structure and differing changes to their structure with different amounts of water uptake. Electrostatic force microscopy (EFM) can map surface charge distribution as nano special resolution by measuring the electrostatic force between a vibrating conductive tip and a charged surface under an applied voltage, . In this study, the ionic channel network of a proton exchange membrane is analyzed using EFM. A mathematical approximation model of the ionic channel network is first derived, to explain changes in force gradient on the surface using EFM. The phase lag of dry and wet Nafion under stepwise changes to bias voltage is then measured. Based on the model, variations in the ionic channel network of Nafion with different amounts of water uptake are analyzed numerically. The mean surface charge density of both membranes, which is connected with the ionic channel network, is calculated using the model. The results show that the difference between the mean surface charge of the dry and wet membranes is consistent with the variation in their proton conductivity.

The spectra and global distributions of the X-ray emissions generated by the solar wind charge-exchange (SWCX) process in the terrestrial magnetosheath are investigated based on a global hybrid model and a global geocoronal hydrogen model. The solar wind O6+ ions which are the primary charge state for oxygen ions in solar wind are considered. The line emissivity of the charge-exchange born O5+ ions are calculated by Spectral Analysis System for Astrophysical and Lab oratory (SASAL). It is found that the emission lines from the O5+ ranges from 105.607 to 118.291 eV with the strong line at 107.047 eV. We then simulated the magnetosheath X-ray emission intensity distributions with a virtual camera at two positions of north pole and dusk at six stages during the passing of a perpendicular interplanetary shock combined with a tangential discontinuity structure through the Earth’s magnetosphere. During this process, the X-ray emission intensity increases with time, and the maximum value is 27.11 keV cm-2 s-1 sr-1 on the dayside, which is 4.5 times that before the solar wind structure reaches the Earth. A clear shock structure can be seen in the magnetosheath and moves earthward. The maximum emission intensity seen at dusk is always higher than that seen at north pole.

Turner syndrome (TS) is caused by a complete or partial absence of an X or Y chromosome, including chromosomal mosaicism, affecting 1 in 2,500 female live births. Sister chromatid exchange (SCE) is used as a sensitive indicator of spontaneous chromosome instability. Cells from mosaic patients constitute useful material for SCE evaluations as they grow under the influence of the same genetic background and endogenous and exogenous factors. We evaluated proliferation dynamics and SCE frequencies of 45,X and 46,XN cells of 17 mosaic TS patients. In two participants, 45,X cells exhibited a proliferative disadvantage in relation to 46,XN cells after 72h of cultivation. The analysis of mean PI showed significant differences between 45,X and 46,XN lineages; however there were no intraindividual differences. On the other hand, mean SCE frequencies showed no differences between the two lineages, but there were intraindividual differences in 5 patients. The absence of mean SCE frequency differences between 45,X and 46,XN lineages may indicate that both were equally unstable, as more than 70% of the 46,XN lineages had an anomalous karyotype. However, 46,XN had a higher mean PI, suggesting that the amount of cells with a karyotype distinct from 45,X may increase with time in mosaic TS women.

As new vaccines reduce P. falciparum (Pf) cases, clinicians can focus on rescuing more children with cerebral malaria (CM). Adjunctive “therapeutically-rational exchange transfusion” (T-REX) refers to using special “Pf-resistant” donor red blood cells (RBCs) that secrete nano-sized RBC extracellular vesicles (EVs). Can some RBC EVs rapidly dislodge Pf-infected RBCs (iRBCs) sequestered in blood vessels and reduce inflammation? Does post-exchange “rebound parasitemia” reflect sequestration-reversal? We reviewed case-reports, EV and liposome studies, expert perspectives, and time-sequence data. In the AQUAMAT study, median coma-recovery time was 20 hours for artesunate. In contrast, a CM patient treated with type-O T-REX quickly began speaking (during the procedure). For other rapid-recovery CM patients, donor RBC variables had not been specified. Despite rapid Pf-killing, drugs need 20 hours to substantially reduce iRBC cytoadhesion while EVs can selectively bind distant inflamed tissues within 15 minutes. RBCs stressed by blood-bank storage and Pf infection secrete EVs. Post-exchange “rebound parasitemia” can occur within 60 minutes and may reflect release of sequestered iRBCs. Sequestration-reversal can be assessed by monitoring Pf parasitemia and total Pf biomass. New data suggest clinicians, working with transfusion- and laboratory-medicine physicians, can, and should, assess T-REX options and publish their findings to help clarify how RBC EVs may serve as therapeutic “decoy ligands.”

Three-dimensional V₂O₅ hollow structures have been prepared through a simple synthesis strategy combining solvothermal treatment and a subsequent thermal annealing. The V₂O₅ materials are composed of microspheres 2–3 μm in diameter and with a distinct hollow interior. The as-synthesized V₂O₅ hollow microspheres, when evaluated as a cathode material for lithium-ion batteries, can deliver a specific capacity as high as 273 mAh·g⁻¹ at 0.2 C. Benefiting from the hollow structures that afford fast electrolyte transport and volume accommodation, the V₂O₅ cathode also exhibits a superior rate capability and excellent cycling stability. The good Li-ion storage performance demonstrates the great potential of this unique V₂O₅ hollow material as a high-performance cathode for lithium-ion batteries.

Ion-exchange membranes (IEMs) are widely used in desalination, waste water treatment, food, energy production and other applications. There is a strong demand for cost-effective IEMs characterized by high selective transport of ions of a certain sign of charge. In this paper, we simulate the experimental results of V. Sarapulova et al. (IJMS 2021) on the modification of an inexpensive anion-exchange membrane (CJMA-7, Hefei Chemjoy Polymer Materials Co. Ltd., China) with a perfluorosulfonated ionomer (PFSI). The modification was made in several stages including keeping the membrane at a low temperature, applying a PFSI solution on its surface, and subsequent drying it at an elevated temperature. We apply the known microheterogeneous model with some new amendments to simulate each stage of the membrane modification. It has been shown that the PFSI film formed on the membrane-substrate does not affect significantly its properties due to the small thickness of the film (4 m) and similar properties of the film and substrate. The main effect is caused by the fact that PFSI material “clogs” the macropores of the CJMA-7 membrane, thereby blocking the transport of coions through the membrane. In this case, the membrane microporous gel phase, which has a high selectivity to counterions, remains the primary pathway for both counterions and coions. Due to the above modification of the CJMA-7 membrane, the coion (Na+) transport number in the membrane equilibrated with 1 M NaCl solution decreased from 0.11 to 0.03. Thus, the modified membrane becomes comparable in its transport characteristics with more expensive IEMs available on the market.

A low-cost bio-mass-derived carbon substrate has been employed to synthesize MoS₂@carbon composites through a hydrothermal method. Carbon fibers derived from natural cotton provide a three-dimensional and open framework for the uniform growth of MoS₂ nanosheets, thus constructing hierarchically coaxial architecture. The unique structure could synergistically benefit fast Li-ion and electron transport from the conductive carbon scaffold and porous MoS₂ nanostructures. As a result, the MoS₂@carbon composites, when served as anodes for Li-ion batteries, exhibit a high reversible specific capacity of 820 mAh g^-1, high-rate capability (457 mAh g^-1 at 2 A g^-1), and excellent cycling stability. The superior electrochemical performance makes the MoS₂@carbon composites to be low-cost and promising anode materials for Li-ion batteries.

This paper presents an optimized energy management strategy for Li-ion power batteries used on electric vehicles (EVs) at low temperatures. Under low-temperature environments, EVs suffer a sharp driving range loss resulted from the energy and power capability reduction of the battery. Simultaneously, because of Li plating, battery degradation becomes an increasing concern as temperature drops. All these factors could greatly increase the total vehicle operation cost. Prior to battery charging and vehicle operating, preheating battery to a battery-friendly temperature is an approach to promote energy utilization and reduce total cost. Based on the proposed LiFePO4 battery model, the total vehicle operation cost under certain driving cycles is quantified in the present paper. Then given a certain ambient temperature, a target temperature of preheating is optimized under the principle of minimizing total cost. As for the preheating method, a liquid heating system is also implemented on an electric bus. Simulation results show that the preheating process becomes increasingly necessary with a decreasing ambient temperature; however, the preheating demand declines as driving range grows. Vehicle tests verify that the preheating management strategy proposed in this paper is able to save total vehicle operation cost.

For both conventional and renewable energy conversion processes, computational fluid dynamics (CFD) has been used to address more energy-related challenges in recent decades. Using CFD to investigate vertical-axis wind turbines has become more common in recent years. The main goals of this application have been to more accurately predict the turbine's performance and to comprehend the complicated nature of the complex turbulent flow. The Vertical Axis Wind Turbine (VAWT) simulation for energy-generating applications has several intricate components. One of them is being aware of the chaotic flow that occurs during the first stages of the starting process, which influences overall effectiveness. In this article, the performance of the wind turbine was increased by using a passive flow control approach. The numerical research was carried out using Large Eddy Simulation for four alternative tip speed ratios in both cases, the classic and the optimized, equipped with a vortex trap on the exterior of the blades. The power and torque coefficient variations, as well as the velocity magnitude contours, show that the starting process may begin with a significant improvement in efficiency when flow control is used.

: In the realm of data management, data preservation stands as a critical undertaking aimed at preserving and upholding the integrity of data. Regardless of whether it concerns personal or enterprise data, the detrimental effects of malicious alterations implemented by attackers cannot be overlooked. Particularly in conventional industrial control environments, the prevalent practice involves the transmission of data from sensors to databases for storage purposes. However, it is essential to recognize that this process exposes the data to various vulnerabilities. Thus, to ensure the long-term security and reliability of the data, it becomes imperative to implement robust data preservation strategies within these industrial control systems. However, the reliance of these databases on physical hard disks introduces inherent vulnerabilities, including the potential for data loss due to disk damage or targeted malicious attacks. Consequently, it becomes imperative to prioritize the implementation of robust data preservation measures. These measures are crucial in mitigating the risk of disruptions and protecting critical data from compromise. By establishing effective data backup systems, employing advanced security protocols, and implementing proactive monitoring mechanisms, organizations can bolster their data preservation capabilities and safeguard against potential threats to data integrity and availability. As a result, many enterprises opt to store their data with third-party providers to ensure data integrity. However, this approach carries inherent risks. If the third-party service experiences an attack or if the data is tampered with, it becomes challenging to verify the integrity of the data. To address these concerns and ensure data preservation within the context of the Internet of Things (IoT), a growing number of individuals are integrating IoT with Distributed Ledger Technology (DLT). By leveraging DLT, the integrity of data can be ensured, reducing reliance on centralized third-party storage and enhancing security in the IoT ecosystem. In this article, IOTA is the DLT, which employs Directed Acyclic Graph (DAG) to store transaction information. Compared to Ethereum or other blockchain technologies, IOTA offers notable advantages in terms of transaction verification speed, making it highly suitable for real-time IoT environments. However, the conventional transmission path from sensors to IOTA nodes entails a complex route, involving multiple hardware devices before reaching the intended destination. This complexity poses challenges in ensuring data integrity during transmission and introduces vulnerabilities such as man-in-the-middle attacks or SQL injection attacks. To address these issues, we propose a method to streamline the transmission path between sensors and IOTA, specifically tailored for industrial fields with numerous IoT devices. Our approach involves preprocessing the data stored on the server using our method before uploading, ensuring data confidentiality, and leveraging IOTA to guarantee data integrity. To achieve the shortest path between IoT and DLT nodes, it becomes necessary to establish IOTA nodes on lower-level devices, such as Raspberry Pi or IoT controllers. By simplifying the transmission path, we can reduce the potential for tampering and enhance overall data security. Implementing our proposed method enables the assurance of data confidentiality and integrity during both transmission and storage on the server, strengthening the trustworthiness of the IoT, and IOTA integration.

We give a simple proof of the Chen inequality for the Chen invariant $\underbrace{\delta (2,...,2)}_{k\mbox{ terms}}$ of submanifolds in Riemannian space forms.

Bio-molecular reagents like antibodies required in experimental biology are expensive and their effectiveness, among other things, is critical to the success of the experiment. Although such resources are sometimes donated by one investigator to another through personal communication between the two, there is no previous study to our knowledge on the extent of such donations, nor a central platform that directs resource seekers to donors. In this paper, we describe, to our knowledge, a first attempt at building a web-portal titled Bio-Resource Exchange that attempts to bridge this gap between resource seekers and donors in the domain of experimental biology. Users on this portal can request for or donate antibodies, cell-lines and DNA Constructs. This resource could also serve as a crowd-sourced database of resources for experimental biology. Further, in order to index donations outside of our portal, we mined scientific articles to find instances of donations of antibodies and attempted to extract information about these donations at the finest granularity. Specifically, we extracted the name of the donor, his/her affiliation and the name of the antibody for every donation by parsing the acknowledgements sections of articles. To extract annotations at this level, we propose two approaches – a rule based algorithm and a bootstrapped relation learning algorithm. The algorithms extracted donor names, affiliations and antibody names with average accuracies of 57% and 62% respectively. We also created a dataset of 50 expert-annotated acknowledgements sections that will serve as a gold standard dataset to evaluate extraction algorithms in the future. Contact: [email protected], [email protected] Database URL: http://tonks.dbmi.pitt.edu/brx Supplementary information: Supplementary data are available at Database online.

In this article, we give a brief review of the origin of the neutrino mass in some interesting non-linear supersymmetric models with R-symmetry. These models are able to address and solve the most important problems of the particle physics and provide mechanisms for neutrino mass generation and their mixing parameters in agreement with the current experimental data. Their prediction could be experimentally tested in the near future by collider experiments.

The paper deals with the problems of direct kinematics related to a 2T6R robot, the direct kinematics of the plane mechanism of the robot. The direct kinematics of this proposed new robot help to study the movement, including the dynamic one, to determine the forces in the mechanism and to model the possible trajectories of the final effector point, thus determining the robot's working space and some of its multiple possible uses. Two totally different methods were used to verify the calculation relations, the results obtained by both methods being practically identical. The first method used is an original trigonometric method, and the second is an original geometrically analytical method.

Dye/salt separation has gained increasing attention in recent years, prompting the quest for cost-effective and environmentally-friendly raw materials for synthesis high performance nanofiltration (NF) membrane for effective dye/salt separation. Herein, a high-performance loose structured NF membrane was fabricated by via a simple vacuum filtration method using a green nanomaterial, 2,2,6,6-tetramethylpiperidine-1-oxide radical (TEMPO)-oxidized cellulose nanofiber (TOCNF), by sequentially filtrating larger-size and finer-size TOCNFs on a microporous substrate, followed by cross-linked with trimesoyl chloride. The resultant TCM membrane possesses a separating layer composed entirely of pure TOCNF, eliminating the need for other polymer or nanomaterials additives. TCM membranes exhibits high performance and effective dye/salt selectivity. Scanning Electron Microscope (SEM) analysis shows that the TCM membrane with Fine-TOCNF layer has a tight layered structure. Further characterizations via Fourier transform infrared spectroscopy (FTIR) and X-ray diffraction (XRD) confirm the presence of functional groups and chemical bonds of the crosslinked membrane. Notably, the optimized TCM-5 membrane exhibits a rejection rate of over 99% for various dyes (Congo red, orange yellow) and 14.2% for NaCl, showcasing a potential candidate for efficient dye wastewater treatment.

In this work, a novel silane coupled cationic precursor (SAGS) was synthesized by 3-glycidyloxypropyltrimethoxysilane and sodium 2-((2-aminorthyl)amino) ethanesulfonate. A series of cation exchange membranes were prepared with poly(vinyl alcohol) (PVA) and SAGS by sol-gel process. The structure of the prepared membranes were characterized by fourier transform infrared spectrum (FTIR) and scanning electron microscopy (SEM), and its properties were studied by water uptake (WR), cation exchange capacity (CEC), linear expansion ratio (LER), alkali stability, thermogravimetric analysis (TGA), mechanical properties and diffusion dialysis performance. FTIR and X-ray photoelectron spectroscopy (XPS）confirmed the successful preparation of SAGS membranes, and SEM images showed that the prepared membranes were dense and uniform. The WR values of the SAGS membranes were in the range of 91.49-122.39 %, and the LER values were 17.65-28.21 %. In addition, the SAGS membranes had suitable CEC value, good alkali resistance and thermal stability which ensured the application of membranes in the field of diffusion dialysis (DD) for alkali recovery. In DD test, the dialysis coefficients of NaOH (UOH) ranged from 0.012 mm/h to 0.023 mm/h, and the separation factors (S) was in the range of 30.77-16.43. In summary, the prepared membrane had good performance and simple preparation process, which had great application potential in textile industrial wastewater recovery.

We have developed IrO_x/M-SnO₂ (M = Nb, Ta, and Sb) anode catalysts, IrO_x nanoparticles uniformly dispersed on M-SnO₂ supports with fused-aggregate structures, which make it possible to evolve oxygen efficiently, even with a reduced amount of noble metal (Ir) in proton exchange membrane water electrolysis. Polarization properties of IrO_x/M-SnO₂ catalysts for the oxygen evolution reaction (OER) were examined at 80 °C in both 0.1 M HClO₄ solution (half cell) and a single cell with a Nafion^® membrane (thickness = 50 μm). While all catalysts exhibited similar OER activities in the half cell, the cell potential (E_cell) of the single cell was found to decrease with the increasing apparent conductivities (σ_{app, catalyst}) of these catalysts: an E_cell of 1.61 V (voltage efficiency of 92%) at 1 A cm^-2 was achieved in a single cell by the use of an IrO_x/Sb-SnO₂ anode (highest σ_{app, catalyst}) with a low Ir-metal loading of 0.11 mg_Ir cm^-2 and Pt supported on graphitized carbon black (Pt/GCB) as the cathode, with 0.35 mg_Pt cm⁻². In addition to the reduction of the ohmic loss in the anode catalyst layer, the increased electronic conductivity contributed to decreasing the OER overpotential due to the effective utilization of the IrO_x nanocatalysts on the M-SnO₂ supports, which is an essential factor in improving the performance with low noble metal loadings.

The per capita availability of freshwater resources on a global scale is gradually decreasing due to population growth, rapid urbanization, industrialization, and modern lifestyles. In this situation, wastewater management becomes a major concern. Conventional treatment processes used to treat wastewater discharges are not adequate for the advanced removal of pollutants, especially refractory organic pollutants, which are mainly organic compounds that are not easily biodegradable in the environment. The use of photocatalytic membrane reactors (PMRs) for tertiary wastewater treatment has attracted much interest in recent periods, and various configurations have been investigated. The performance of a PMR using an iron doped titanium photo catalyst and Polysulfone-based polymeric membrane for municipal wastewater treatment was evaluated under natural and simulated solar light. Obtained results proved that solar driven PMRs can remove organic loading (COD) with high efficiencies and may represent a suitable alternative for the tertiary treatment step of municipal wastewater.

This study presents the synthesis and electrochemical evaluation of nitrogen-doped vanadium oxide (N-V2O3/C) as a cathode material for aqueous zinc-ion batteries (AZIBs), using a hydrothermal method. Compared to undoped V2O3/C, N-V2O3/C exhibits enhanced electrical conductivity, capacity, and electrochemical kinetics, attributed to the incorporation of pyridinic and pyrrolic nitrogen. Initial charge-discharge cycles indicate phase transitions to amorphous vanadium oxides, enhancing conductivity. N-V2O3/C shows a high specific capacity of 168.4 mAh g−1 at 10 A g−1 and remarkable reversibility, highlighted by the transient existence of intermediate species during cycling. Optimal electrochemical performance is achieved with a vanadium to nitrogen molar ratio of 2:3, indicating the significant impact of nitrogen doping concentration on the material’s efficiency. This work underscores the potential of N-V2O3/C as a superior cathode material for AZIBs.

A hybrid material, consisting of commercially available nitrocellulose (NC) membrane non-covalently modified with amino-polyethylene glycol functionalized reduced graphene oxide (NH2-PEG-rGO) nanoparticles, was successfully synthesized for oligonucleotide extraction. Fourier Transform Infrared Spectroscopy (FTIR) confirmed the modification of the NC membrane, revealing characteristic peaks of both compounds NC and NH2-PEG-rGO. Scanning Electron Microscopy (SEM) exhibited morphological changes in the NC/NH2-PEG-rGO hybrid membrane, marked by the introduction of NH2-PEG-rGO particles, resulting in a distinctly smothered surface compared to the porous surface of the NC control membrane. Wettability assays revealed hydrophobic behavior for the NC/NH2-PEG-rGO hybrid membrane, with a water contact angle exceeding 90°, contrasting with the hydrophilic behavior characterized by a 16.7° contact angle in the NC membrane. The performance of the NC/NH2-PEG-rGO hybrid membrane was evaluated for the extraction of ssDNA with fewer than 50 nucleotides from solutions containing various ionic species (MnCl2, MgCl2, and MnCl2/MgCl2). The NC/NH2-PEG-rGO hybrid membrane exhibited optimal performance when incubated in MgCl2, presenting the highest fluorescence emission at 525 relative fluorescence units (r.f.u.). This corresponds to the extraction of approximately 610 pg (≈13%) of the total oligo-DNA, underscoring the efficacy of the pristine material, which extracts 286 pg (≈6%) of oligo-DNA in complex solutions.

Polymer inclusion membranes (PIMs), which contained cellulose tri-acetate used as a polymer base, a plasticizer in the form of o-NPOE, and meso-tetra methyl tetrakis-[methyl-2-(4-acetlphenoxy)] calix[4]pyrrole (KP) used as a carrier, were prepared and tested for the effective purification of aqueous solutions of methylene blue dye. The scanning electron microscope (SEM), thermogravimetric analysis (TGA), and attenuated total reflection Fourier transform infrared (ATR-FTIR) were used to define the microstructure and surface of PIMs. Experimental results showed that with the increased concentration of methylene blue in an aqueous solution, the removal percentage also increased. Further observation also showed that the flux increased with the rise of the source phase pH values from 3 to 10. The carrier and plasticizer content in the membrane significantly influenced the membrane’s transport properties. The optimal composition of the membrane in per cent by weight was for KP: 74% plasticizer; 18% support; 8% carrier. It was shown that the membrane with optimal composition showed good reusability and enabled the easy and spontaneous separation of methylene blue from aqueous solutions.

Based on the need for real-time sag monitoring of Overhead Power Lines (OPL) for electricity transmission, this article presents the implementation of a hardware and software system for online monitoring of OPL cables and cable sag determination. The mathematical model based on differential equations and the methods of algorithmic calculation of OPL cable sag are presented. Considering that, based on the mathematical model presented, the calculation of OPL cable sag can be done in different ways depending on the sensors used, and the presented application uses a variety of sensors. Therefore, a direct calculation is made using one of the different methods. Subsequently, the verification relations are highlighted directly and, respectively, the calculation by the alternative method, which uses another group of sensors, to generate both a verification of the calculation and the functionality of the sensors, thus obtaining a defect observer of the sensors. The hardware architecture of the OPL cable online monitoring application is presented, together with the main characteristics of the sensors and communication equipment used. The configurations required to transmit data using the ModBUS and ZigBee protocols are also presented. The main software modules of the OPL cable condition monitoring application are described, which ensure the monitoring of the main parameters of the power line and the visualisation of the results both on the electricity provider's intranet using a web server and MySQL database, and on the Internet using an Internet of Things (IoT) server. This categorisation of the data visualisation mode is done in such a way as to ensure a high level of cyber security. Starting from the mathematical model of the OPL cable sag calculation, it goes through the stages of creating such a monitoring system, from the numerical simulations carried out using Matlab to the real-time implementation of this monitoring application. The main modules of the application software are: the software module for reading quantities from the sensor network through a ModBUS Input/Output (I/O) server, the software module for real-time calculation of the OPL cable sag, the software module for read/write operations based on MySQL type data, the software module for transferring data to the user's intranet through a web server, and the software module for viewing data by authorised users based on user and password through an IoT server. The development software environments used are Matlab and Laboratory Virtual Instrument Engineering Workbench (LabVIEW).

Introduction: Atrial fibrillation (AF) is a common cardiac arrhythmia whose prevalence rises with age and is linked to increased morbidity and mortality due to the risk of thromboembolism. Management typically involves anticoagulation and rhythm control, but the treatment of elderly patients with multiple comorbidities requires careful consideration of drug side effects and interactions. Cibenzoline, a Vaughan-Williams class IA antiarrhythmic, is effective against AF but has risks of toxicity, especially in older people and those with renal impairment, due to its renal excretion and prolonged half-life in these populations. Discussion: This paper presents a case of an 80-year-old woman with paroxysmal AF who suffered cardiac arrest due to cibenzoline toxicity despite receiving standard adjusted dosages. The patient's cibenzoline blood concentration was significantly higher than the therapeutic range, leading to cardiotoxicity, which was exacerbated by drug interactions with bisoprolol and edoxaban, both metabolized by the CYP3A4 enzyme. Venoarterial extracorporeal membrane oxygenation (V-A ECMO) and intra-aortic balloon pump (IABP) successfully managed the cardiac arrest. This case emphasizes the unpredictable pharmacokinetics of cibenzoline in elderly patients with renal impairment and the need for vigilant therapeutic drug monitoring to avoid adverse events. Conclusions: Cibenzoline can pose a significant risk of severe toxicity in elderly patients with renal impairment, and drug interactions may potentiate this risk. The paper underscores the importance of careful dose adjustment and monitoring of drug levels in this population. In cases of cibenzoline-induced cardiac arrest, V-A ECMO and IABP are effective treatment modalities. The case study serves as a critical reminder for clinicians to remain vigilant for drug-induced complications and to apply aggressive supportive treatments when necessary.

In this study the impact of terrorist attacks on exchange rate is estimated. Particularly, the study focuses on Turkish terrorist attacks and its implication on Turkish lira versus pound sterling exchange rate. In order, to find the causal effect the study employed Autoregressive distributive lag (ARDL) bound testing approach as an estimation technique. Accordingly, the analysis reveals that terrorist attack has a negative impact on the exchange rate in both short and long-run. However, the negative effect of terrorism tends to be small in both the short-run and long-run. More precisely, terrorist attack depreciates the exchange rate between Turkish lira and pound sterling by approximately 0.00072 in the next trading day. The long-term effect also shows that terrorist attack depreciates the exchange rate on average by 0.00212.

Modern exchange theories model a large market, but do not explain single exchange. The paper considers the phenomenon of single exchange and formulates the general exchange problem in the form of a system of two equations, subjective and objective. Subjective equilibrium is given by the Walras-Jevons marginal utility equation. Objective equilibrium equations by Walras and Jevons are averaged over all transactions in the market and can only give a rough general picture without explaining the specific price of an individual exchange. An exchange micro-condition must be found that, when averaged, will give the Walras market equilibrium macro-condition. The study of the internal structure of exchange leads to the need to consider power. The concept of generalized power is introduced. It is generalized power that serves as the primary comparable and measurable objective basis of exchange. The power theory of exchange provides the objective price-equation. It is demonstrated that money is a measure of generalized power in exchange and a certification of generalized power in subsequent exchanges. The proposed theory is able to uniformly explain any exchange, including a single one, which is impossible with the existing theories of exchange.

Two polyurethanes (PUs) were similarly synthesized by reacting a cycloaliphatic isocyanate with 1,4 butanediol and two polyols of different nature (polyester, polycarbonate diol) with molecular weights of 1000 Da. The PU made with polycarbonate diol polyol (YCD) was the only showing intrinsic self-healing at 20 °C. For assessing the mechanism of intrinsic self-healing of YCD, a structural characterization by molecular weights determination, infrared and X-ray photoelectronic spectroscopies, differential scanning calorimetry, X-ray diffraction, thermal gravimetric analysis and dynamic mechanical thermal analysis was carried out. It was concluded that the self-healing at 20 °C of YCD was due to non-covalent dynamic exchange interactions among the carbonate groups of the soft segments. Therefore, the chemical nature of the polyol played a key role in developing PUs with intrinsic self-healing at 20 °C.

Even though the current classic aerospace propulsion methods are greatly improved, some of the most modern methods have already been introduced, among which the propulsion with electric motors. Energy can be obtained from hydrogen burners, honeycomb burners to protect the burning of hydrogen that burns 10 times faster than conventional oil fuels or alcohols. Hydrogen storage is also done in honeycomb cell reservoirs. Getting solar photovoltaic power even during flight is not yet profitable or efficient, but it can be proposed in the future for lighter and/or spacecraft. A great desire is to dismantle water in hydrogen and oxygen directly on the aircraft, so the stored fuel is actually water and the one actually used is the hydrogen removed from the water. In this case, there is no need for hydrogen storage. And other modern methods of propulsion and energy acquisition are briefly presented in the paper.

Dysregulation of cartilage homeostasis and the changes in the density and the architecture of the subchondral bone were postulated as a potent mechanically pathological activity contributing to osteoarthritis (OA) pathogenesis. Extracorporeal shockwave therapy (ESWT) is a new, none invasive and effective method in the treatment of animal OA model. In the current study, we demonstrated that shockwave induced the expression of protein-disulfide isomerase-associated 3 (Pdia-3) which is a multifunctional protein hypothesized to be a significant mediator for 1α,25-Dihydroxyvitamin D3 (1α,25(OH)₂D₃) signaling pathway using two-dimensional electrophoresis. Histological analysis and quantitative polymerase chain reaction (qPCR) were verified and observed that the expression of Pdia-3 at 2 weeks was significantly higher than that of any other group at 4 weeks, 8 weeks, and 12 weeks post-shockwave treatment in early OA knee of rat. The other factors of the 1α,25(OH)₂D₃ rapid membrane signaling pathway including extracellular signal-regulated protein kinases 1 (ERK1), osteopontin (OPG), alkaline phosphatase (ALP), and matrix metallopeptidase 13 (MMP13) were measured and significantly increased by qPCR at 2 weeks post-shockwave treatment in early OA knee. Our proteomic data revealed significant Pdia-3 expression in microenvironments of joint tissue that could be actively responded to ESWT, which may potentially regulate biological function of chondrocytes and osteoblasts in the treatment of OA knee.

Solvent-free, single-ion conducting electrolytes are sought after for use in electrochemical energy storage devices. Here, we investigate the ionic conductivity and how this property is influenced by segmental mobility and conducting ion number in crosslinked single-ion conducting polyether-based electrolytes with varying tethered anion and counter-cation types. Crosslinked electrolytes are prepared by the polymerization of poly(ethylene glycol) diacrylate (PEGDA), poly(ethylene glycol) methyl ether acrylate, and ionic monomers. The ionic conductivity of the electrolytes is measured and interpreted in the context of differential scanning calorimetry and Raman spectroscopy measurements. A lithiated crosslinked electrolyte prepared with PEG₃₁DA and STFSI monomers is found to have a lithium ion conductivity of 3.2 × 10^-6 and 1.8 × 10⁻⁵ S/cm at 55 and 100 °C, respectively. The percentage of unpaired anions for this electrolyte was estimated at about 23% via Raman spectroscopy. Despite the large variances in metal cation – STFSI binding energies as predicted via DFT and large variations in ionic conductivity, STFSI-based crosslinked electrolytes with the same charge density and varying cations (Li, Na, K, Mg, and Ca) were estimated to all have unpaired anion populations in the range of 19 to 29%.

Artificial membrane systems can serve as models to investigate molecular mechanisms of different cellular processes, including transport, pore formation, and viral fusion. However, the current simulacrums such as SUVs, GUVs, and the supported lipid bilayers suffer from issues, namely high curvature, heterogeneity, and surface artefacts, respectively. Freestanding membranes provide a facile solution to these issues, but current systems developed by various groups use silicon or aluminium oxide wafers for fabrication that involves access to a dedicated nanolithography facility and high cost while conferring poor membrane stability. Here, we report the development, characterization and applications of an easy-to-fabricate suspended lipid bilayer (SULB) membrane platform leveraging commercial track-etched porous filters (PCTE) with defined microwell size. Our SULB system offers a platform to study the lipid composition-dependent structural and functional properties of membranes with exceptional stability in a high throughput fashion. With dye entrapped in PCTE microwells by SULB, we show that sphingomyelin significantly augments the activity of pore-forming toxin, Cytolysin A (ClyA) and the pore formation induces lipid exchange between the bilayer leaflets. Further, we demonstrate high efficiency and rapid kinetics of membrane fusion by dengue virus in our SULB platform. Our suspended bilayer membrane mimetic offers a novel platform to investigate a large class of biomembrane interactions and processes.

This paper presents a device for measuring and maintaining the constant water level in a tank. The device uses a capacity sensor to measure the water level. The sensor has a DC voltage output proportional to the water level in the tank. This voltage can be used in other automation too. The water level, in percentages, is displayed on a vu meter with 8 LEDs. The circuit for maintaining the constant level consists in a comparator with hysteresis. The level of the water is adjustable, using a reference voltage from a potentiometer (marked in percentages). The level of the water is compared with the prescribed level and the difference between them commands the start/stop of the water pump which supplies the tank through a relay. The device is powered by 220 V and is isolated from the environment.

The Golgi apparatus, long known for protein processing and vesicular trafficking, has recently emerged as an essential player in innate immune signaling pathways. This review article discusses our growing understanding of Golgi cells' roles in initiating and activating innate immunity pathways. We elaborate on the relevance of membrane connections between Golgi organelles and other organelles such as endoplasmic reticulum, mitochondria, endosomes, and autophagosomes that facilitate efficient access to innate immune signal transduction and subsequent effector responses. Additionally, we discuss microbial strategies that exploit the Golgi while diminishing its associated innate immune responses. By providing greater illumination of its multiple functions and mechanisms of operation, this article offers invaluable insight into how protein processing impacts innate immunity and vice versa.

Abstract: Building Information Modelling (BIM) methodology has been empowering the quality of the construction activity in all sectors: multidisciplinary designs development; construction planning and monitoring; building management and maintenance. A BIM environment aggre-gates several disciplines and different professional skillsets and in order to control and improve the quality of a BIM project, a BIM manager is required. The BIM manager has the responsibility to coordinate all tasks involved in a building design and associated activities usually workout over the project documents. This professional can access to the distinct discipline models, located in a shared platform, and request for amendments if inconsistencies are detected. The topic of the present study is illustrated with three building cases were distinct specific projects, disciplines and tasks were elaborated: collaboration between disciplines (architecture, structures and con-struction); structural analyses and reinforcement details; quantity take-off of materials and cost estimation; construction scheduling and simulation. Although there are still limitations in the implementation of BIM methodology in all sectors and stages, within the construction industry, BIM has been bringing an important improvement in the quality of a building design, reflected in the quality of the final product. The present study put in evidence the BIM manager role in pro-jects that aggregates several disciplines and experts, bringing an important contribution in the quality of a building design. BIM methodology is a current demand in the construction industry supported on advanced technology and in an adequate management of projects.

The Foreign Exchange rate is very much crucial for determining the economic health level of the country. The foreign exchange rate provides financial stability, enhances purchasing power and allows global trades. This rate usually fluctuates due to the market forces which control the supply and demand of the currency. Nominal and relative inflation and income level have a substantial effect on determining the exchange rates. Government measures, international situations, natural disasters or any unexpected situation like Covid-19, Rohingya crisis etc. can affect the exchange rates. Besides this, the interaction between the factors can create different reasoning to affect the market. This study tries to identify some factors with relevant examples.

We introduce a novel key exchange protocol based on non-commutative matrix multiplication defined in $\mathbb{F}_p^{n \times n}$. The security of our method does not rely on computational problems as integer factorization or discrete logarithm whose difficulty is conjectured. We show that the public, secret and channel keys become indistinguishable to the eavesdropper under matrix multiplication. Remarkably, for achieving a 512-bit security level, the public key is 1024 bits and the private key is 768 bits, making them the smallest keys among post-quantum key exchange algorithms. Also, we discuss how to achieve key authentication, interdomain certification and Perfect Forward Secrecy (PFS). Therefore, Lizama's algorithm becomes a promising candidate to establish shared keys and secret communication between (IoT) devices in the quantum era.

We introduce a novel key exchange protocol based on non-commutative matrix multiplication defined in $\mathbb{Z}_p^{n \times n}$. The security of our method does not rely on computational problems as integer factorization or discrete logarithm whose difficulty is conjectured. We claim that the unique eavesdropper's opportunity to get the secret/private key is by means of an exhaustive search which is equivalent to the unsorted database search problem. Furthermore, we show that the secret/private keys become indistinguishable to the eavesdropper. Remarkably, to achieve a 512-bit security level, the keys (public/private) are of the same size when matrix multiplication is done over a reduced 8-bit size modulo. Also, we discuss how to achieve key certification and Perfect Forward Secrecy (PFS). Therefore, Lizama's algorithm becomes a promising candidate to establish shared keys and secret communication between (IoT) devices in the quantum era.

Radiotherapy using accelerated charged particles is rapidly growing worldwide. About 85% of the cancer patients receiving particle therapy is irradiated with protons, which have physical advantages compared to X-rays but similar biological response. In addition to the ballistic advantages, heavy ions present specific radiobiological features that can make them attractive for treating radioresistant, hypoxic tumors. An ideal heavy ion should have lower toxicity in the entrance channel (normal tissue), and being exquisitely effective in the target region (tumor). Carbon ions have been chosen because they represent the best combination in this direction. Normal tissue toxicities and second cancer risk are similar to those observed in conventional radiotherapy. In the target region, they have increased relative biological effectiveness and reduced oxygen enhancement ratio compared to X-rays. Some radiobiology properties of densely ionizing carbon ions are so distinct from X-rays and protons that they can be considered as a different “drug” in oncology, and may elicit favorable responses such as increased immune response and reduced angiogenesis and metastatic potential. The radiobiological properties of carbon ions should guide patient selection and treatment protocols to achieve optimal clinical results.

The metastatic disease is a complex and sequential process that involves the migration of tumor cells from the primary site to distant areas. This metastatic pathway is not always predictable. Therefore, this paper presents three rare cases of unusual metastases, due to their primary site: two metastases of a clear cell renal cell carcinoma, one gingival and one nasal, as well as a mandibular metastasis of a hepatocellular carcinoma. In all cases, an incisional biopsy was performed in order to sign out the diagnosis. After microscopical examination of morphological Hematoxylin and Eosin stained slides, for all cases, immunohistochemical reactions were performed to support the primary tumor site. Two cases had a previous histopathological diagnosis of a primary tumor, while for the third case, the metastatic lesion represented the first manifestation of the neoplastic disease, with an unfavorable prognosis.

Background: Trans-septal endocardial left ventricle lead placement is an alternative technique used capture the left ventricular endocardially but it is use is limited due lack of evidence, practice uptake and clinical trials. we evaluated the efficiency of the procedure, post procedural complication rate, rate of thromboembolic events as well as changes in echocardiographic parameters, brain natriuretic peptide (BNP) level and the New York Heart Association (NYHA) class. Results: TSLV lead implant is safe, improves ejection fraction, LVEDV, LVESV, LVIDd. Significantly reduces NTproBNP levels and NYHA class. Stroke rate was reported only in one patient (9%), noticeably, this particular patient was on DOAC rather than anti-vitamin K antagonists. In this group, patients, who were on Warfarin , were not reported to have any thrombo-embolic events. Discussion: Trans-septal endocardial LV lead implant in patients with a failed CS approach remains a viable alternative however, there is a higher risk of stroke amongst these patients, as well as more procedure related risk of complications compared to conventional CRT. The data analysis demonstrates that patients undergoing a TSLV lead implant due to a failed trans-venous approach have more advanced heart failure, defined by their higher NYHA class compared to conventional trans-venous CRT implant groups. Their pre TSLV implant, echocardiographic parameters are also worse compared to trans-venous CRT implant group

Membrane-based sensors (MePSs) exhibit remarkable precision and sensitivity in detecting pressure changes. MePSs are commonly used to monitor catalytic reactions in solution, generating gas products crucial for signal amplification in bioassays. They also allow catalyst quantification by indirectly measuring the pressure generated by the gaseous products. This is particularly interesting to detect enzymes in biofluids associated with disease onset. To enhance the performance of a MePS, various structural factors influence membrane flexibility and response time, ultimately dictating the device's pressure sensitivity. In this study, we fabricated MePSs using polydimethylsiloxane (PDMS) and investigated how structural modifications affect the Young's modulus (E) and residual stress (σ0) of the membranes. These modifications have a direct impact on the sensors' sensitivity to pressure variations, observed as a function of the volume of the chamber (Σ) or of the mechanical properties of the membrane itself (S). MePSs exhibiting the highest sensitivities were then employed to detect catalyst quantities inducing the dismutation of hydrogen peroxide, producing dioxygen as gaseous product. As a result, catalase enzyme was successfully detected using these optimized MePSs, achieving a remarkable sensitivity of (22.7 ± 1.2) µm/nM and a limit of detection (LoD) of 396 pM.

Mandibular critical size defect (CSD) due to pathological conditions, trauma, and congenital disease can not heal spontaneously and predominantly filled with fibrous tissue. Therefore, a Guided Bone Regeneration (GBR) combined with bone grafting can be performed. The researchers considered using Demineralized Dentin Material Membrane (DDMM) from bovine dentine as an alternative GBR. This study aimed to determine the amount of fibroblast and collagen density after DDMM and bone graft implantation on CSD. Thirty-six Rattus norvegicus rats were used as samples. Mandibular bone defect 5x5 mm was made, then filled with bone graft and covered with Bovine Pericardium Collagen Membrane (BPCM) in the control group and DDMM in the treatment group. Six samples were sacrificed on 7, 14, and 21 days post-surgical for histology examination. There were no significant differences in the amount of fibroblast and collagen density (p-value > 0,05). The amount of fibroblast is lower and the collagen density is higher in treatment group. DDMM has microporosity to prevent connective tissue ingrowth and dentine tubules to allow growth factors release. DDMM and bone graft implantation can reduce the amount of fibroblasts and increase collagen density of CSD which potentially being used as a CSD alternative treatment for bone regeneration.

This study conducts a comprehensive review of the integration of Hybrid Electric Turbochargers in mass-produced road vehicles. The primary objective is to inform the readers about the potential advantages and innovative applications of HETs. Employing a SWOT analysis, the research compares the performance of HETs on thermal engines versus traditional turbochargers and HETs on thermal engines versus HETs on hybrid engines based on a synthesis of multiple research findings. The study elucidates the fundamental mechanics of turbochargers, emphasizing their inherent benefits. Additionally, it introduces a novel approach with the integration of the hy-brid-electric turbocharger, demonstrating its capacity, supported by practical examples. The in-corporation of turbochargers with energy recovery mechanisms, including HETs, is shown to significantly contribute to emissions reduction. Moreover, the electric drive facilitates the utili-zation of hybrid turbines, particularly on low-displacement engines, resulting in enhanced effi-ciency, torque, and liter power. In conclusion, the research underscores the potential of HETs to substantially mitigate the environmental impact of the transportation sector by reducing emis-sions and conserving energy. Their ability to optimize the fuel efficiency and power output of internal combustion engines, coupled with the feasibility of downsized engines, positions HETs as an attractive option for both manufacturers and consumers. However, it is acknowledged that the implementation of HETs is in its early stages, necessitating further research to comprehensively understand their environmental impact. Despite this, the promising positive impact on the en-vironment designates HETs as a technology deserving close attention in the forthcoming years.

Inflation and exchange rates have great influence on consumer prices especially on imports and exports. Exchange rate fluctuations create inefficiency and distort world prices whereas changes in inflation rates have a direct impact on consumer goods prices which incidentally include exchange rates. There is a direct interdependence between inflation and exchange rates and this paper is aimed at investigating this relationship in dynamic context. It tries to find out how changes in inflation and exchange rates impact on another by adopting the econometric and copula approaches. Both inflation and exchange rates data are susceptible to volatility clustering, possess fat tails and are skewed coupled with conditional heteroskedasticity. Hence we model the univariate distributions by using ARMA$(p,q)$-GARCH$(x,y)$ so as to capture the most important stylized features of inflation and exchange rates. A bivariate model is then constructed by coupling the marginal distributions of inflation and exchange rates using the survival Clayton copula. Empirical results from monthly inflation and exchange rates data show positive correlation between the two based on Kendall $\tau$ test which confirms that a change in inflation results in change of exchange rates an vice versa hence there is co-movement. Furthermore, by the Granger causality test, exchange rates spikes cause changes in inflation rates. The results of the study have implications on economic policy design and hedging strategies for traders on imports and exports.

Biological membranes are fascinating. Santiago Ramón y Cajal, who received the Nobel prize in 1906 together with Camillo Golgi for their work on the nervous system, wrote “[..]in the study of this membrane[..] I felt more profoundly than in any other subject of study the shuddering sensation of the unfathomable mystery of life”[1]. The visualization and conceptualization of these biological objects have profoundly shaped many aspects of modern biology, drawing inspiration from experiments, computer simulations, as well as from the imagination of scientists and artists. The aim of this review is to provide a fresh look on current ideas of biological membrane organization and dynamics by discussing selected examples across fields [1] The full quotation is “I must not conceal the fact that in the study of this membrane I for the first time felt my faith in Darwinism (hypothesis of natural selection) weakened, being amazed and confounded by the supreme constructive ingenuity revealed not only in the retina and in the dioptric apparatus of the vertebrates but even in the meanest insect eye. There, in fine, I felt more profoundly than in any other subject of study the shuddering sensation of the unfathomable mystery of life.” from the autobiography Recollections of My Life.

Iodide is an essential micronutrient present in very small quantities in the human body, with a fundamental action for the adequate synthesis of thyroid hormones, which are critical for cell differentiation, growth and metabolism. In the form of iodide, iodine is widely distributed in the environment, although in an irregular manner, occurring in abundant amounts in the oceans and in coastal areas and scarcely found on islands and mountains. The diet is the main source of iodine, whose intake varies according to the amount present in soil and water and according to eating habits. Governmental policies have been adopted to satisfy and guarantee the necessary daily supply of iodine, such as fortification of industrialized salt for domestic iodine consumption or addition to the bread commonly consumed in a given region, or the offer of iodized oil to the population, or even iodine supplementation through medications. Iodide deficiency is the main avoidable cause of brain damage to fetuses and children, as well as retardation of psychomotor development. Thyroid hormones are almost universally involved in the development and proliferation of fetal neural tissue. Permanent lesions of the cerebral cortex, hippocampus and cerebellum may occur, with loss of, or damage to the brainstem or spinal cord, affecting cortical areas that integrate highly specialized stimuli, which become poorly defined on an anatomical basis, including silent areas of the associative cortex. One of the more significant metabolic problems due to dietary iodine deficiency is the presence of goiter (increased volume of the thyroid gland). Thyroid carcinoma is the most frequent endocrine neoplasia affecting the human species and plasma iodine concentration is related to the development of specific subtypes of this neoplasia. An increased prevalence of follicular carcinoma, a more aggressive tumor, has been observed in areas of iodine deficiency, while the correction of this deficiency is associated with a higher prevalence of papilliferous carcinoma, a less aggressive form. CONCLUSION: An ideal plasma iodide concentration is necessary to insure the proper mental development of fetuses and young children and to minimize the aggressiveness of thyroid cancer from follicular cells in humans.

The most common and taught membrane theory assumes that the membrane behaves as a kind of electrical capacitance that is exposed to an electrical current generated by an ionic flow. If this statement is verifiable, it can be confirmed by the laws of physics, mathematics and in particular electricity. We will demonstrate that this hypothesis is not verified and that it is necessary to modify biophysics according to already established and experimentally verified principles of physics.

Recent advances in synthetic membranes allow their use in fields as diverse as food and agriculture, biotechnology, industrial wastewater treatment, and potable water production. Among the newly developed technologies, nanofiltration for liquids and more particularly for desalination of seawater or saline aquifers are actively pursued. However, current solid-state membranes performance is limited, which calls for the development of novel formulations for membranes offering both high permeability (ion and water flux) and ion differentiation (selectivity), usually considered antagonist features. We report the development of hybrid nanoporous membranes made of solid-state polymeric carbonate track-etched (PCTE) thin films in which biological ion channels such as Gramicidin A (GA), alpha-hemolysin (α-HL), and outer-membrane protein F (OmpF) aquaporin are confined and graphene oxide (GO) conjugated cobalt ion selective binding peptide motifs (Copep) are adsorbed, referring as bioinspired and biomimetic approaches, respectively. These solid-state nanoporous membranes are attracting widespread attention since they offer scalability, mechanical robustness, selectivity, controlled pore dimension and shape, for water sustainability. The ion permeability, ion diffusion coefficient and selective ion recognition are evaluated via nanofiltration, cell diffusion kinetics, and UV-Visible absorption spectroscopy to gain insights into the role of key performance parameters including effective ion confinement in track-etched pores, rich surface chemistry, and peptide-induced channel for selective ion transport. These findings provide new avenues for artificial ion channels by synergistic combination of eco-friendly material design such as GO enabled by bio-molecular recognition chemistry.

We used LA-ICP-MS U-Pb data for detrital zircon to constrain the Maximum Depositional Age (MDA) and provenance of clastic sedimentary rocks of the Volyn-Orsha sedimentary basin, which filled an elongated (~625×250 km) depression in SW Baltica and attained ~900 m in thickness. Eighty-six zircons out of one hundred and three yielded concordant dates, with most of them (86 %) falling in the time interval between 1655 ± 3 and 1044 ± 16 Ma and clustering in two peaks at ca. 1630 and 1230 Ma. The remaining zircons yielded dates older than 1800 Ma. The MDA is defined by a tight group of three zircons with a weighted average age of 1079 ± 8 Ma. This age corresponds to the time of a clockwise ~90° rotation of Baltica and the formation of the Grenvillian – Sveconorwegian – Sunsas orogenic belts. Subsidence was facilitated by the presence of eclogites derived from subducted oceanic crust. The sediments of the Orsha sub-basin in the northeastern part of the basin were derived from the local crystalline basement, whereas the sediments in the Volyn sub-basin, extending to the margin of Baltica, were transported from the orogen between Laurentia, Baltica, and Amazonia.

In Shark Bay, a large hypersaline bay in Western Australia, longitudinal density gradients force gravitational circulation that is important for Bay-ocean exchange. Observations of vertical stratification and velocity are presented, confirming a steady near-bed dense water outflow from Shark Bay’s northern Geographe Channel that persisted through all stages of the tide. Outflow velocities were 2–3 times stronger than the outflows recorded previously in Naturaliste Channel (in the west) and were more resistant to breakdown by tidal mixing. Estimates of turbulent kinetic energy production derived from ADCP data using the variance method showed a more complex structure in Geographe Channel, due to shear associated with the stratified conditions, with peak levels of turbulence occurring during reversal of tidal flows. For both channels the main source of turbulence was tidal flow along the seabed, with the bottom current speed cubed, |U_b³|, providing a reasonable proxy for tidal mixing and prediction of dense water outflows from Shark Bay the majority of the time. Orientation and deeper water of Geographe Channel along the main axis of the longitudinal density gradient provided an explanation for the predominant outflow from the Bay’s northern entrance. These density-driven currents could potentially influence recruitment of commercially fished scallops and prawns through dispersal and flushing of larvae.

In the last 20 years, an increasing number of studies have been reported on membrane active peptides, which exert their biological activity by interacting with the cell membrane either to disrupt it and lead to cell lysis or to translocate through it to deliver cargos into the cell and reach their target. These peptides are attractive alternatives to currently used pharmaceuticals. Antimicrobial peptides (AMPs) and peptides designed for drug and gene delivery currently in the drug pipeline suggest that these membrane active peptides will soon constitute a significant percentage of the drug market. Here, we focus on two most prominent classes of membrane active peptides; AMPs and cell-penetrating peptides (CPPs). AMPs are a group of membrane active peptides that disrupt the membrane integrity or inhibit the cellular functions of bacteria, virus and fungi. CPPs are another group of membrane active peptides that mainly function as cargo-carriers even though they may also show antimicrobial activity to some extent. Biophysical techniques to understand how they interact with the membrane have shed light on the peptide–membrane interaction at various levels of detail. Structural investigation of membrane active peptides in the presence of the membrane provides important clues on the effect of the membrane environment on peptide conformations. Advances in live imaging techniques have allowed examination of peptide action at a single cell or single molecule level. In addition to these experimental biophysical techniques, molecular dynamics simulations provided clues on the peptide-lipid interactions and dynamics of the cell entry process at atomic detail. In this review, we summarize the recent advances in experimental and computational investigation of membrane active peptides with particular emphasis on two amphipathic membrane active peptides, the AMP melittin and the CPP pVEC.

Reduced-order electrothermal models play a key role in the design and control of lithium- ion cell stacks, calling for accurate model parameter calibration. This paper presents a complete electrical and thermal experimental characterization procedure for coupled modeling of cylindrical lithium-ion cells in order to implement them in a prototype Formula SAE hybrid racing car. The main 4goal of the tests is to determine cell capacity variations with temperatures and discharge currents, to predict the open circuit voltage of the cell and its entropic component. A simple approach for the characterization of the battery equivalent electrical circuit and a two-steps thermal characterization method are also shown. The investigations are carried out on four commercial 18650 NMC lithium cells. The model demonstrated to predict the battery voltage at a RMS error lower than 20mV and the temperature to a RMS error equal to 0.5 ◦C. The authors hope that this manuscript can contribute to the development of standardized characterization techniques for such cells, while offering experimental data and validated models that can be used by researchers and BMS designers in different applications.

We report on the successful preparation of wet dressings hydrogels based on Chitosan-Poly(N-Vinyl-Pyrrolidone)-Poly(ethylene glycol)-Poly(acrylic acid) and Poly(ethylene oxide) by e-beam cross-linking in weakly acidic media, to be used for rapid healing and pain release of infected skin wounds. The structure and compositions of hydrogels investigated according to sol-gel and swelling studies, network parameters, as well as FTIR and XPS analyses showed the efficient interaction of the hydrogel components upon irradiation, maintaining the bonding environment while the cross-linking degree increasing with the irradiation dose and the formation of a structure with the mesh size in the range 11-67 nm. Hydrogels with gel fraction above 85% and the best-swelling properties in different pH solutions were obtained for hydrogels produced with 15 kGy. The hydrogels are stable in the simulated physiological condition of an infected wound and show appropriate moisture retention capability and the water vapor transmission rate up to 272.67 g m-2 day-1, to ensure fast healing. The hydrogels proved to have a significant loading capacity of ibuprofen (IBU), being able to incorporate a therapeutic dose for the treatment of severe pains. Simultaneously, IBU was released up to 25% in the first 2h, having a release maximum after 8h.

The generation and maintenance of membrane potential is a fundamental part of Membrane Pump Theory. One of the key points of this hypothesis is based on a natural or facilitated molecular diffusion through several types of ion channels and pumps like the Na/K ATPase. Chemistry, physics and especially electrochemistry, however, bring strong contradictions to this theoretical assumption. By respecting the principles of chemistry and electrostatics, it becomes obvious that this theoretical hypothesis cannot work. The ionic diffusion that would be at the origin of this potential cannot take place. Indeed, the topology and the forces involved definitively exclude the current model, which must absolutely be revised according to the current state of our knowledge and allow an advance in the understanding of the phenomena and open new research perspectives.

The exploitation of lipid membranes in biosensors has provided the ability to reconstitute a considerable part of their functionality to detect trace of food toxicants and environmental pollutants. Nanotechnology enabled sensor miniaturization and extended the range of biological moieties that could be immobilized within a lipid bilayer device. This chapter reviews recent progress in biosensor technologies based on lipid membranes suitable for environmental applications and food quality monitoring. Numerous biosensing applications are presented, putting emphasis on novel systems, new sensing techniques and nanotechnology-based transduction schemes. The range of analytes that can be currently detected include, insecticides, pesticides, herbicides, metals, toxins, antibiotics, microorganisms, hormones, dioxins, etc. Technology limitations and future prospects are discussed, focused on the evaluation/ validation and eventually commercialization of the proposed sensors.

In order to alter and adjust the shape of the membrane, cells harness various mechanisms of curvature generation. Many of these curvature generation mechanisms rely on the interactions between peripheral membrane proteins, integral membrane proteins, and lipids in the bilayer membrane. One of the challenges in modeling these processes is identifying the suitable constitutive relationships that describe the membrane free energy that includes protein distribution and curvature generation capability. Here, we review some of the commonly used continuum elastic membrane models that have been developed for this purpose and discuss their applications. Finally, we address some fundamental challenges that future theoretical methods need to overcome in order to push the boundaries of current model applications.

The exploitation of lipid membranes in biosensors has provided the ability to reconstitute a considerable part of their functionality to detect trace of food toxicants and environmental pollutants. Nanotechnology enabled sensor miniaturization and extended the range of biological moieties that could be immobilized within a lipid bilayer device. This chapter reviews recent progress in biosensor technologies based on lipid membranes suitable for environmental applications and food quality monitoring. Numerous biosensing applications are presented, putting emphasis on novel systems, new sensing techniques and nanotechnology-based transduction schemes. The range of analytes that can be currently detected include, insecticides, pesticides, herbicides, metals, toxins, antibiotics, microorganisms, hormones, dioxins, etc. Technology limitations and future prospects are discussed, focused on the evaluation/ validation and eventually commercialization of the proposed sensors.

Wound healing involves physical, chemical and immunological processes. Transient receptor potential (TRP) and other ion channels are implicated in epidermal re-epithelization. Ion movement across ion channels can induce transmembrane potential that leads to transepithelial potential (TEP) changes. TEP present in epidermis surrounding the lesion decreases and induces an endogenous direct current generating an epithelial electric field (EF) that could be implicated in wound re-epithelialization. TRP channels are involved in the activation of immune cells during the inflammatory phase of wound healing. The aim of the study was to review the mechanisms of ion channel involvement in wound healing in in vivo experiments in rodents (mice, rats, rabbits) and how can this process be influenced. This review used the latest results published in scientific journals over the last year and this year to date (1 January 2023–31 December 3000) in order to include the in-press articles. Some types of TRP channels, such as TRPV1, TRPV3, and TRPA1, are expressed in immune cells and can be activated by inflammatory mediators. The most beneficial effects in wound healing are produced using agonists of TRPV1, TRPV4 and TRPA1 channels or by inhibiting with antagonists, antisense oligonucleotides or knocking down TRPV3 and TRPM8 channels.

The purported cognitive benefits associated with nicotine and its metabolites in the brain are a matter of debate. In this review, the impact of the pharmacologically active metabolite of a nicotine derivative produced by bacteria (6-hydroxy-L-nicotine) on memory, oxidative stress, and the activity of the cholinergic system in the brain was examined. A search in the PubMed, Science Direct, Web of Science, and Google Scholar databases, limiting entries to those no later than July 2023, was conducted. The search focused specifically on articles pertaining to nicotine metabolites, memory, oxidative stress, cholinergic system activity, as well as enzymes or pathways related to nicotine degradation in bacteria. The preliminary search resulted in 696 articles, and following the application of exclusion criteria, 185 articles were deemed eligible for inclusion. This review focuses on experimental studies supporting nicotine catabolism in bacteria, and the chemical and pharmacological activities of nicotine and its metabolite 6-hydroxy-L-nicotine.

In the electric distribution systems, the “Smart Grid” concept is implemented to encourage energy savings and integration of the innovative technologies, helping the Distribution Network Operators (DNOs) in choosing the investment plans which to lead the optimal operation of the networks and increasing the energy efficiency. In this context, a new phase load balancing algorithm was proposed to be implemented in the low voltage distribution networks with hybrid structures of the consumption points (switchable and non-switchable consumers). It can work in both operation modes (on-line and off-line), uploading information from different databases of the DNO which contain: the consumers’ characteristics, the real loads of the consumers integrated into the Smart Metering System (SMS), and the typical load profiles for the consumers non-integrated in the SMS. The algorithm was tested in a real network, having a hybrid structure of the consumption points, on a time interval by 24 hours. The obtained results were analyzed and compared with other algorithms from the heuristic (Minimum Count of Loads Adjustment algorithm) and the metaheuristic (Particle Swarm Optimization and Genetic Algorithms) categories. The best performances were provided by the proposed algorithm, such that the unbalance coefficient resulted in the smallest value (1.0017). The phase load balancing led to the following technical effects: decreasing the average current in the neutral conductor with 94% and for the energy losses with 61.75 %, and increasing the minimum value of the phase voltage at the farthest pillar with the 7.14 %, compared to the unbalanced case.

Experimental systems to simulate future elevated CO2 conditions in the field often have large, rapid fluctuations in CO2. To examine possible impacts of such fluctuations on photosynthesis, intact leaves of field grown plants of five species were exposed to two-minute cycles of CO2 between 400 and 800 mol mol-1 lasting a total of 10 minutes, with photosynthesis, stomatal conductance and PSII fluorescence measured at the end of each half-cycle, and also 10 minutes after the end of the cycling. Prior to the cyclic CO2 treatments, steady-state responses of leaf gas exchange and fluorescence to CO2 were determined. In four of the five species, in which stomatal conductance decreased with increasing CO2, the cyclic CO2 treatments reduced stomatal conductance. In those species, both photosynthesis and the photochemical efficiency of PSII were reduced at limiting internal CO2 levels, but not at saturating CO2. In the fifth species, there was no change in stomatal conductance with CO2, and no change in either photosynthesis or PSII efficiency at any CO2 level with CO2 cycling. It is concluded that in many, but not all, species fluctuations in CO2 may reduce photosynthesis at low CO2 partly by decreasing the photochemical efficiency of photosystem II, as well as by decreasing stomatal conductance.

The majority of E-commerce transactions reveal private information such as customers' identities, order contents, and payment information during the transaction. Other personal information such as health conditions, religion, and even ethnicity may be also deduced. Even when deploying electronic cryptocurrencies such as Bitcoin, anonymity cannot be fully guaranteed. Also, many anonymous payment schemes suffer from possible double spending circumstances. E-commerce privacy is basically a difficult problem as it involves parties with concurring interests. Three major e-commerce requirements are highly difficult to resolve: anonymous purchase, anonymous delivery, and anonymous payment. This work presents a possible e-commerce system addressing all three anonymity requirements for electronic-items business on open networks. The system offers anonymous entities authentication mechanisms up to completing a fair anonymous e-commerce transaction. The system is based on deploying a physically clone-resistant hardware token for each relevant involved party. The tokens are made clone-resistant by accommodating a Secret Unknown Cipher (SUC) in each hardware-token as a digital PUF-like identity. A set of novel generic system-setups for units, protocols and e-commerce schemes is introduced. The proposed anonymization is basically attained by virtually-replacing relevant e-commerce entities by low-cost, unique and clone-resistant tokens/units using SUCs. The units act as trustable anonymous, authenticated and non-replaceable entities monitored by their acting users.

This work shows the physicochemical and mineralogical characterization of diatomites form the Hidalgo and Jalisco States, Mexico. In the case of the mineral from Hidalgo State, this has the following chemical composition; 70.0 % wt. SiO₂, 11.63 wt. % Al₂O₃, 1.95 wt. % FeO, 1.79 wt. % MgO, 2.41 wt. % K₂O, 0.85 wt. % CaO and 6.10 wt. % Na₂O. On the other hand, the mineral from Jalisco has the following chemical composition; 93.58 wt. % SiO₂, 3.03 wt. % Al₂O₃, 1.81 wt. % FeO, 0.40 wt. % MgO, 0.92 wt. % K₂O, 0.11 wt. % CaO and 0.24 wt. % Na₂O. For recovery of metals, both minerals got arsenic, silver, lead and nickel recoveries upper to 95 % and lower to 10 % for chromium. According to efficiency of interchange, the mineral from Hidalgo is slightly higher in the case of arsenic, lead and silver; while for nickel and particularly chromium (VI) the efficiency is higher for the mineral from Jalisco.

In this paper, I propose new models of quantum information processing using the exchange interaction in physical systems. The partial SWAP operator that can be realized using the exchange interaction is used as the underlying resource for defining models of quantum computation, quantum communication, quantum memory and decoherence-free subspaces. Given the non-commutativity of these operators (for adjacent operators operating on a common qubit), a number of quantum states and entanglement patters can be obtained. This zoo of states can be classified, due to the parity constraints and permutation symmetry of the states, into invariant subspaces that are used for the definition of some of the applications in this paper.

First of all the paper presents a solid solution of piezoelectric ceramic that was synthesized according to the general formula Pb(1-x)Srx(Ti0.48Zr0.52)(1-y)NbyO3 with x = 0.05 and y = 0.02, using wet ceramic processing technology and using an oxide mix as prime material. The effects of dopants (Sr2+ and Nb5+) on phase constitution, on microstructure and on the dielectric and piezoelectric properties were determinate. The Zr/Ti ratio was chosen near the morphotropic phase boundary of the PZT system in studied composition. The XRD data revealed that the PZT doped composition had tetragonal perovskite structure. Secondly the paper presents the design of the novel piezo-motor based on a surface wave which translates the linear extension of different piezoelectric segments of a piezoelectric cylinder into a rotational bending movement. This rotational bending of the piezoelectric cylinder is then transformed into a continuous rotation of the rotor through a calculated contact. The design of the motor takes advantage of the high piezoelectric constants of the developed material in an optimal way in order to increase the energetic efficiency. A brief mathematical model of electromechanical answer of piezoelectric materials is presented as it was used in the modeling of the material during the numerical simulations.

This study examines the effectiveness of a comprehensive psychomotor development program combined with adapted football training for adolescents diagnosed with intellectual disabilities in Romania. Twelve participants, with a mean age of 17.42 years underwent a carefully designed intervention program spanning 36 weeks. The program aimed to enhance fundamental movement skills, integrate these skills into specialized football training, and culminate in a Unified 7-a-side Football Match. Results indicate significant improvements in psychomotor skills, including static and dynamic balance, pulse processing speed, and identified stimuli. Moreover, the intervention positively impacted social interaction among participants. Statistical analysis, employing Pearson Correlation Analysis and Paired Samples t-Test (One-Sample), compared assessments. Results revealed significant differences between pre- and post-intervention measurements, providing robust evidence of the program's efficacy. The positive correlations between physical parameters and social interaction highlight the interconnectedness between physical fitness and social engagement. Our findings suggest that improvements in physical abilities may contribute to increased social interaction among children with intellectual disabilities, underscoring the holistic nature of our intervention, which addresses multiple dimensions of development simultaneously. The findings underscore the holistic benefits of integrating psychomotor development and adapted football programs for adolescents with intellectual disabilities, emphasizing the importance of promoting inclusive physical activities for their overall well-being.

In time, osteoarthritis (OA) generates the misalignment of the affected joint structures. However, due to the nature of bipedal gait, OA in the lower limb can also cause pathological gait patterns, which can generate instability and falls, with great consequence, especially in the aged population. With goniometry used to evaluate the range of motion of joints (ROM), we wanted to evaluate how gender impacts gait dynamics in OA patients. For this study we have compared 106 OA patients (male=32, female=74) to age matched controls. All participants had their right leg as dominant. Video recording of normal gait was analysed with a digital goniometry tool phone application, and the knee’s ROM was measured in midstance and midswing of the gait. During midstance, significant extension and flexion of the knee excursion have been observed in both males and females. During midswing, knee OA presents more differences, whereas subjects with hip and knee OA present changes on the dominant knee. Midstance changes suggest that the knee’s joint degenerative changes can be linked to hip OA secondary changes. Midswing changes in lower limb OA suggest a connection to the activities of daily life. Gender differences generated by OA must furthermore be studied in both lower limbs so that the best therapeutic approach can be chosen.

Hepatocellular carcinoma (HCC) is a heterogeneous malignancy with complex carcinogenesis. Although there has been significant progress in the treatment of HCC over the past decades, drug resistance to chemotherapy remains a major obstacle in its successful management. In this study we were able to reduce chemoresistance in cisplatin-resistant HepG2 cells by either silencing the expression of transglutaminase type 2 (TG2) using siRNA or by pre-treatment of cells with the TG2 enzyme inhibitor cystamine. Further analysis revealed that, whereas the full-length TG2 isoform (TG2-L) was almost completely cytoplasmic in its distribution, the majority of the short TG2 isoform (TG2-S) was membrane-associated in both parental and chemoresistant HepG2 cells. Following induction of cisplatin toxicity in non-chemoresistant parental cells, TG2-S together with cisplatin quickly relocated to the cytosolic fraction. Conversely, no cytosolic relocalisation of TG2-S or nuclear accumulation cisplatin was observed following identical treatment of chemoresistant cells, where TG2-S remained predominantly membrane-associated. This suggests that deficient subcellular relocalisation of TG2-S from membranous structures into the cytoplasm may limit the apoptic response to cisplatin toxicity in chemoresistant cells. Structural analysis of TG2 revealed the presence of binding motifs for interaction of TG-S with the membrane scaffold protein LC3/LC3 homologue that could contribute to a novel mechanism of chemotherapeutic resistance in HepG2 cells.

Conventional economic theory outlines that developing countries experience economic growth through an undervalued exchange rate and that exchange rate overvaluations has negative long term effects on economic growth. This paper examined the impact of exchange rate movements as well as exchange rate misalignments on economic growth for the Trinidad and Tobago economy over the period 1960 to 2016. We find statistically significant evidence that both exchange rate appreciation and misalignments impact negatively on economic growth in the T&T economy. Drilling deeper we find interestingly that there exist no non-linear effects of exchange rate misalignments on growth. Specifically we find statistically significant evidence that both overvaluations and undervaluations hamper economic growth in the Trinidad and Tobago economy. We attribute this to T&T’s small and underdeveloped manufacturing sector that tends to be overlooked on account of its energy resources, in addition to the fact that its manufacturing sector is highly import oriented. A major policy recommendation would be for the critical reassessment of the rules governing the HSF, as government expenditure was allowed to follow energy revenues due to its current limitations.

Background: Previous papers have developed a statistical mechanics of neocortical interactions (SMNI) fit to short-term memory and EEG data. Adaptive Simulated Annealing (ASA) has been developed to perform fits to such nonlinear stochastic systems. An N-dimensional path-integral algorithm for quantum systems, qPATHINT, has been developed from classical PATHINT. Both fold short-time propagators (distributions or wave functions) over long times. Previous papers applied qPATHINT to two systems, in neocortical interactions and financial options. Objective: In this paper the quantum path-integral for Calcium ions is used to derive a closed-form analytic solution at arbitrary time that is used to calculate interactions with classical-physics SMNI interactions among scales. Using fits of this SMNI model to EEG data, including these effects, will help determine if this is a reasonable approach. Method: Methods of mathematical-physics for optimization and for path integrals in classical and quantum spaces are used for this project. Studies using supercomputer resources tested various dimensions for their scaling limits. In this paper the quantum path-integral is used to derive a closed-form analytic solution at arbitrary time that is used to calculate interactions with classical-physics SMNI interactions among scales. Results: The mathematical-physics and computer parts of the study are successful, in that there is modest improvement of cost/objective functions used to fit EEG data using these models. Conclusions: This project points to directions for more detailed calculations using more EEG data and qPATHINT at each time slice to propagate quantum calcium waves, synchronized with PATHINT propagation of classical SMNI.