It is important to realize the transformation behavior of wüstite because it greatly affects the final structure of the oxide layer and the surface quality of the steel products. In the present study, the transformation behaviors of the wüstite layer are examined under nearly-oxygen-free conditions, to simulate the cooling processes after the hot rolled strip is coiled. As the single phase wüstite was prepared at 950˚C, the 460˚C transformed oxide layer was composed of a mixture of iron and magnetite formed through eutectoid reactions. For the 750˚C-fabricated wüstite, only magnetite was observed after transformation, without iron precipitates and residual wüstite. It is speculated that the unusual transformation behavior of the low-temperature-made wüstite results from the pseudo-structural intermediate phase transformation between wüstite and magnetite. This pseudo-structure is a pre-transformed wüstite and of various concentration of ferrous ion, which is determined by the fabrication conditions. During the hot strip mill process, the so-called wet scale, wüstite, is produced continuously from finish mill to laminar flow sections and ended at 570˚C. Consequently, the final eutectoid transformation below 570˚C is dominantly controlled by the surface temperature ranged from 750˚C to 950˚C for low carbon steel.

Pathogenic microorganisms can cause a range of infectious diseases and are often treated with antimicrobial agents. The rise of antimicrobial resistance caused by inappropriate use of these agents in various settings has become a global health threat. There is, therefore, a need to find new and effective agents to combat infections caused by resistant pathogens. Nanotechnology has seen significant growth and development in recent years and has a wide range of applications in various fields, including health, agriculture, and industry. This novel area offers the potential for the synthesis of nanoparticles (NPs) with antimicrobial activity, such as iron oxide nanoparticles (IONPs). The use of IONPs is a promising way to overcome antimicrobial resistance or pathogenicity because of their ability to interact with several biological molecules and to inhibit microbial growth. This review focuses on the most common green synthesis methods for producing IONPs using bacteria, fungi, plants, and organic waste, as well as the most common methods for the characterization of these IONPs. Finally, it summarizes their application as promising antibacterial, antifungal, antiparasitic, and antiviral agents.

We present a simple strategy to generate a family of carbon dot/iron oxide nanoparticles (C/Fe-NPs) that relies on the thermal decomposition of iron (III) acetylacetonate in the presence of a highly fluorescent carbon-rich precursor, while polyethylene glycol serves as the passivation agent. By varying the molar ratio of the reactants, a series of C/Fe-NPs have been synthesized with tuneable elemental composition in terms of C, H, O, N, Fe. The quantum yield is enhanced from 6% to 9% as the carbon content increases from 27% to 36%, while the room temperature saturation magnetization is improved from 4.1 emu/g to 17.7 emu/g as the iron content is enriched from 17 to 31%. In addition, the C/Fe-NPs show excellent antimicrobial properties, minimal cytotoxicity and demonstrate promising bioimaging capabilities, thus showing great potential for the development of advanced diagnostic tools.

Magnetic nanoparticles based on iron oxides (MNPs-Fe) with magnetite or maghemite phases have been widely employed in bio-applications. Thus, they have been used as contrast agents in magnetic resonance imaging (MRI) and oncological treatments through different therapies. Besides, due to the vast health problem of multidrug-resistant bacterial infections, several studies have proposed MNPs-Fe as photothermal agents (PTAs) within antibacterial photothermal therapy (PTT). This work presents a quick and easy green synthesis (GS) to obtain MNPs-Fe using orange peel extract from orange waste from local commerce, which presents an environmentally friendly approach compared to traditional methods such as coprecipitation. The GS can be irradiated with microwaves to reduce the synthesis time drastically. We evaluated the weight yield of the GS and the physical-chemical and magnetic features of the synthesized MNPs-Fe. Besides their cytotoxicity in animal cell line ATCC RAW 264.7, their antibacterial activity against Staphylococcus Aureus (S. Aureus) and Escherichia Coli (E. Coli) was assessed. We found that the MNPs-Fe synthesized using the GS, with 50% v/v of NH4OH and 50% v/v of orange peel extract (50GS-MNPs-Fe) had an excellent weight yield, negligible cytotoxicity for concentrations of MNPs-Fe below 250 µg·mL-1 in 24 hours, and 8 days. In the MNPs-Fe surface, we identified a coating of organic molecules (~ 25 nm) such as terpenes, aldehydes, etc. MNPs-Fe inhibited S. Aureus and 2.54 log10 (CFU) of E. Coli under red LED light irradiation (630 nm, 65.5 mW·cm-2, 30 min). Likewise, they exhibited a superparamagnetic (SPM) behavior for temperatures above 60 K, with a size of 49.3±9.6 nm and saturation magnetization (Ms) of 72.83 and 44.16 emu·g-1 at 60 and 300 K, respectively. Therefore, 50GS-MNPs-Fe are excellent candidates as broad-spectrum PTAs in antibacterial PTT, magnetic hyperthermia (MH), or MRI.

Magnetic iron oxide particles are used for in vitro diagnostics for nearly 40 years. Due to their unique physical, chemical, thermal and mechanical properties, as well as biocompatibility and low toxicity in the human body, iron oxide nanoparticles have been used in many biomedical applications, such as contrast agents for magnetic resonance imaging, carriers for controlled drug delivery and immunoassays, but also in magnetic hyperthermia. Our aim is to investigate the effect of pressure and temperature on the structural, thermal and magnetic properties of iron oxide nanomaterials prepared by hydrothermal synthesis. Iron oxide nanoparticles were synthesized at temperatures of 100-200°C and pressures of 20-1000 bar. It has been found that pressure influences the type of iron oxide crystalline phase. Thus, for lower pressure values (< 100 bar), iron oxide is predominantly formed as hematite, while at pressures > 100 bar, the major crystalline phase is goethite. The complex thermal analysis revealed the polymorphic changes of iron oxides at different temperatures. The existence of specific magnetite and hematite phases in all thermally treated samples are evidenced through the specific Verwey and Morin transitions highlighted by ZFC-FC (Zero Field Cooled-Field Cooled) measurements, whereas their relative content is precisely provided by Mössbauer spectroscopy.

Replacing carbon by hydrogen is a huge step towards reducing CO₂ emissions in the iron- and steel-making industry. The reduction of iron oxides using hydrogen plasma smelting reduction as an alternative to conventional steel-making routes has been studied at Montanuniversitaet Leoben, Austria. The aim of this work was to study the slag formation during the reduction process and the reduction behaviour of iron oxides. Furthermore, the reduction behaviour of iron ore during continuous feeding was assessed. Mixtures of iron ore and calcined lime with a basicity of 0, 0.8, 1.6, 2.3, and 2.9 were melted and reduced by hydrogen. The off-gas composition was measured during the operations to calculate the process parameters. The reduction parameters, namely the degree of reduction, degree of hydrogen utilisation, produced iron, and slag, are presented. The results of the batch-charged experiments showed that at the beginning of the reduction process, the degree of hydrogen utilisation was high, and then, it decreased over the operation time. In contrast, during the continuous-feeding experiment, the degree of hydrogen utilisation could be kept approximately constant. The highest degrees of reduction and hydrogen utilisation were obtained upon the application of a slag with a basicity of 2.3. The experiment showed that upon the continuous feeding of iron ore, the best conditions for the reduction process using hydrogen could be applied.

Urinary tract infections (UTIs) caused by pathogens, particularly E. coli, have spontaneously become resistant to antimicrobial drugs in recent years. Therefore, regular monitoring and alternative strategies for the antimicrobial agent are crucial for combating antimicrobial resistance and bacterial biofilms. Here, we report a new cobalt iron oxide-conjugated tin oxide nanocomposite that can kill bacteria and treat multidrug-resistant E. coli posing UTIs. Following the isolation and identification of E. coli, we tested 57/134 samples against sixteen commonly used antibiotics phenotypically using the disk diffusion method to determine their sensitivity pattern. Of the 57 E. coli isolates, 66% (38/57) were multidrug-resistant. The E. coli isolates were resistant to cephradine (70.17%), ceftriaxone (59.64%), and azithromycin (59.64%), followed by cefixime (54.38%), cefuroxime sodium (52.63%), and co-trimoxazole (50.87%). X-ray diffraction results showed the crystallite sizes were about 5.68 and 8.84 nm in pure SnO2 nanoparticles and 95% SnO2-5% CoFe2O4 nanocomposite, respectively. Energy-dispersive X-ray spectroscopy and Fourier transform infrared determined the fundamental structure of the nanocomposite, encompassing Co, Fe, Sn, and O. Moreover, FTIR measurements implied that the distinct functional groups in both SnO2 and CoFe2O4 nanoparticles existed in a 95% SnO2-5% CoFe2O4 nanocomposite. Field emission scanning electron microscope analysis uncovered that the SnO2-CoFe2O4 nanocomposite had a size of roughly 24 nm and was spherical. In addition, the biosynthesized SnO2 nanoparticles and SnO2-CoFe2O4 nanocomposite were evaluated for their antibacterial activity. At a minimum 100 µg/mL concentration, SnO2 nanoparticles and SnO2-CoFe2O4 nanocomposite showed high antibacterial activity. The SnO2 nanoparticles and SnO2-CoFe2O4 nanocomposite demonstrated antibacterial activity on multidrug-resistant E. coli at 10 ± 0.7 and 16 ± 0.8 mm zone of inhibition, respectively. In conclusion, the new SnO2-CoFe2O4 nanocomposite might be a potential candidate for treating UTIs caused by drug-resistant E. coli in the foreseeable future.

Iron oxide nanoparticles are widely used as contrast agent for MRI and may be used as therapeutic agent by magnetic hyperthermia if they display a high magnetic anisotropy. Considering the effect of the nanoparticles shape on anisotropy, the reproducible shape control of nanoparticles is currently a challenge of synthesis methods. By investigating reaction parameters which are the iron precursor structure, the water content and the amount of the surfactant, sodium oleate, reported to trigger the cubic shape, iron oxide nanoparticles with different shape and composition were observed to form. In particular, iron oxide nanoplates have been thus synthesized. The effect of the surfactant coming from precursor was taking into account by using in house iron stearates bearing either two or three stearate chains and the negative effect of water on shape was confirmed by considering these precursors after their dehydration. Nanocubes with straight faces and a FeO@Fe3-xO4 composition were obtained only with dehydrated precursors and 50% of sodium oleate in the oleic acid and sodium oleate surfactant mixtures. When iron stearates with three chains led mainly to nanocubes in presence of soduim oleate, Iron stearates with two chains led to the formation of nanoplates with 80% of sodium oleate. The original flat shape of the plates was confirmed with 3D TEM tomography. The investigation of the synthesis mechanisms confirmed the major role of deprotonated carboxylic acid and of the heating rate to drive the cubic shape of nanoparticles and showed that the nanoplate formation would depend mainly on the nucleation step and possibly on the presence of a given ratio of oleic acid and deprotonated carboxylic acid.

Iron oxide nanozymes are a form of nanomaterial with both superparamagnetic and enzyme-mimicking properties. Given the multifunctional nature of iron oxide nanozymes, it is attractive for creating iron oxide hybrid nanozymes through biomolecular modifications to imbue with auxillary properties. Such iron oxide hybrid nanozymes can be useful for rapid and cost-effective analysis of circulating tumor nucleic acids (ctNAs) in patient liquid biopsies during minimal residual disease (MRD) monitoring of cancer recurrence. Herein, the use of streptavidin-modified iron oxide hybrid nanozymes is reported for magnetic enrichment and bioelectrocatalytic sensing of three prostate cancer (PCa) ctRNA biomarkers with high detection specificity and sensitivity (10 copies) over an ultrabroad dynamic range (five orders of magnitude). Furthermore, the feasibility of ctRNA analysis for pre- and post-cancer treatment MRD monitoring is demonstrated using PCa urinary liquid biopsy samples.

Photothermal therapy (PTT) can overcome cancer treatment resistance by enhancing cell membrane permeability, facilitating drug accumulation, and promoting drug release within the tumor tissue. Iron oxide nanoparticles (IONPs) have emerged as effective agents for PTT due to their unique properties and biocompatibility. Approved for the treatment of anemia, as MRI contrast agents, and as magnetic hyperthermia mediators, IONPs also offer excellent light-to-heat conversion and can be manipulated using external magnetic field for targeted accumulation in specific tissues. Optimizing parameters such as laser wavelength, power density, shape, size, iron oxidation state, functionalization, and concentration is crucial for IONPs effectiveness. In addition to PTT, IONPs enhance other cancer treatment modalities. They improve tumor oxygenation enhancing the efficacy of radiotherapy and photodynamic therapy. IONPs can also trigger ferroptosis, a programmed cell death pathway mediated by iron-dependent lipid peroxidation. Their magneto-mechanical effect can exert mechanical force on cancer cells to destroy tumors, minimizing damage to healthy tissues. This review outlines strategies for managing photothermal performance and PTT efficiency with iron oxide nanoparticles, as well as synergies with other cancer therapies.

Pretreatment of cells with proteolysis inhibitors diminished intensity and changed shape of DNICs specific EPR signal in a treatment time-dependent manner. The level of DNIC formation was significantly influenced by the presence of protein degradation products. Interestingly, formation of HMWDNICs depended on the availability of LMWDNICs. The extent of glutathione involvement in the in vivo formation of DNICs is minor yet noticeable, aligning with our prior research findings.

Arsenic (As) is the most poisonous metalloid with negative effects on the plant and ecosystem. In the current study, observed that iron oxide nanoparticles (NPs) affected the molecular features of rice under arsenic (As) stress. The result showed that 1-D electrophoresis (SDS-PAGE) demonstrated variable expression of protein profiles. The polypeptide pattern was altered in the SDS-PAGE under arsenic stress. The findings also showed that low molecular weight polypeptides (MTs) expression was maximum under arsenic stress, while iron oxide NPs decreased the expression of these polypeptides and reduced the arsenic stress. RT-PCR was used to analyse the expression of the MYB transcriptional factor, WRKY, and OsGF14 genes in the rice plant. The results showed that these genes were up-regulated in response to arsenic stress, iron oxide NPs reduced arsenic stress, and Myeloblastosis (MYB), WRKY, and OsGF14 genes had very low expression levels. Our work showed that iron oxide nanoparticles (NPs) not only reduced the effects of arsenic stress but also decreased the expression of stress-related genes and metallothioneins (MTs).

Integrating nanomaterials like carbon nanotubes (CNTs) and iron oxide (Fe₃O₄) into epoxy composites has significant interest due to their potential to enhance mechanical properties. This study evaluates the impact of dispersion quality on the mechanical performance of CNT/Fe₃O₄/Epoxy composites, comparing stirring and sonication methods at three different loadings: 0.1, 0.3, and 0.5 wt.%. Tensile testing revealed that sonicated composites consistently outperformed stirred composites, with a significant increase in elastic modulus and ultimate tensile strength (UTS). However, fracture strain decreased in both composite types compared to pure epoxy, with sonicated composites experiencing a more significant reduction than stirred composites. These results underscore the importance of high-quality dispersion for optimizing mechanical properties.

The regulation of cell death is a fundamental issue in cell biology and continues to be intensely investigated worldwide. The significance of research in this field persists because understanding the determinants of cell lifespan directly impacts the maintenance of multicellular organism homeostasis and, consequently, is crucial for addressing biomedical challenges associated with various diseases. It is recognized that the initiation of cell death can be prompted by both specific signals (such as cytokines or hormones) and nonspecific stimuli, including radiation, temperature increase, or oxidants. When these factors affect a cell, numerous signaling pathways are triggered in the cell, leading to neutralization of the effects of their negative effects or, in case of irreparable damage, to cell elimination. This removal of damaged cells occurs through apoptosis or programmed cell death, a highly regulated process. Numerous signaling molecules participate in orchestrating the apoptotic process, many of which also govern other essential functions within the organism. Physiological factors capable of triggering the apoptotic program in cells include nitric oxide (NO), which serves as one of the key signaling molecules regulating the functions of the cardiovascular, nervous, and immune systems of the organism. The unique chemical nature of NO, along with its numerous intracellular targets and physiologically active redox forms, raises questions about the specific mechanisms through which NO exerts its damaging effects on cells. Utilizing pharmacological preparations- such as sources (donors) of exogenous nitric oxide- represents an approach to investigating the initiation and execution of the apoptotic program in sensitive target cells. Furthermore, this approach holds promise as a direction for discovering new selective drugs.

For the last two decades, an increasing demand for low-cost adsorbents for drinking water treatment has been challenged in the rural areas of developing countries that have problems with arsenic (As) contamination. In this work, spent bleaching earth (SBE), a residual material that is formed during the process of refining vegetable oil, has been utilized to prepare the new magnetic adsorbent Fe-SBE/C by modifying its surface area through calcination and co-precipitation with iron. The experimental results demonstrate that Fe-SBE/C exhibits a substantial adsorption capacity towards both arsenite (As(III)) and arsenate (As(V)). Optimal pH conditions were found to be pH 10 for As(III) and pH 3 for As(V), resulting in adsorption percentages of 76.7% and 94.1%, respectively. Other experimental parameters such as calcination conditions, adsorbent dosage, iron-loading ratio, and the presence of co-existing ions were thoroughly investigated. The kinetic study revealed that the adsorption processes follow the Elovich and intraparticle diffusion models, suggesting a combined adsorption mechanism of boundary layer control and chemisorption. Furthermore, the isotherm followed the Langmuir model with a maximum adsorption capacity of 202.61 μg g-1 for As(III) and 187.61 μg g-1 for As(V). Through thermodynamic analysis and reinforcement by activation energy data, this research validates that the observed adsorption process is indicative through chemisorption. The regeneration study revealed the potential for multiple cycles of arsenic removal, highlighting the practical applicability of Fe-SBE/C in environmental contexts. In conclusion, the findings of this study underscore the efficacy of Fe-SBE/C in arsenic removal and present it as a promising and environmentally friendly solution for mitigating arsenic pollution.

Medical imaging is an active field of research that fosters the necessity for novel multimodal imaging probes. In this line, nanoparticle-based contrast agents are of special interest, since those can host functional entities either within their interior, reducing potential toxic effects of the imaging tracers, and on their surface, providing high payloads of probes, due to their large surface-to-volume ratio. The long-term stability of the particles in solution is an aspect usually under-tackled during probe design in research laboratories, since their performance is generally tested briefly after synthesis. This may jeopardize a later translation into practical medical devices, due to stability reasons. To dig into the effects of nanoparticle aging in solution, respect to their behavior in vivo, iron oxide stealth nanoparticles were used at two stages (3 weeks vs. 9 months in solution), analyzing their biodistribution in mice. Both sets of nanoprobes showed similar sizes, zeta potentials and morphology, as observed by DLS and TEM but, fresh nanoparticles accumulated in the kidneys after systemic administration, while aged ones accumulated in liver and spleen, confirming an enormous effect of particle aging on their in vivo behavior, despite barely noticeable changes perceived on a simple inspection of their structural integrity.

Iron (Fe), the main component of non-exhaust particulates, is known to have variable health effects that depend on the chemical species of iron. This study characterized the possible contribution of iron oxides and hydroxides to airborne brake-wear particles under realistic vehicle driving and braking conditions with different brake-pad friction materials. We found significant differences in wear coefficients and PM₁₀ emissions between non-asbestos organics (NAO) and European performance (ECE) brake pads. Iron was the dominant contributor to PM₁₀ and PM_2.5 brake-wear particles for both NAO and ECE. The iron concentration ratio in the particle mass were comparable to the disc to pads ratio measured by wear mass. The fact that magnetite, which is of interest with respect to health effects, was less abundant in NAO than in ECE suggested that tribo-oxidations occurred in NAO. Metallic iron is generated not only from abrasive wear but also from tribo-chemical reduction with magnetite as the starting material. We found differences not only in PM emissions between brake friction materials but also that the phase transformations of iron differed between friction materials. These differences were apparent in the distribution of iron oxides and hydroxides. Heat, tribo-oxidation, and tribo-reduction are intricately involved in these reactions.

The combination of organic matter, iron oxide, and clay minerals is of great significance for the adsorption of copper ions (Cu). The purpose of this study is to explore the characteristics of Cu adsorption and laws governing Cu complexation to organic–inorganic, organic–clay mineral, and iron-oxide–clay mineral complexes in the sediments in the estuary of plateau fault and sinking lake——Dianchi Lake. In this study, Cu adsorption tests were performed on the three complexes, in order to study the kinetic behavior of adsorption, Langmuir and Freundlich isotherm models were used. The samples before and after adsorption were characterized via scanning electron microscope (SEM), Fourier infrared spectroscopy (FTIR), and X-ray diffraction (XRD). Our results show that, the Freundlich isotherm models model was able to describe adsorbent behavior in comparison to the Langmuir models. During the Cu adsorption process, the iron-oxide–clay mineral complex is able to adsorb Cu, via coordination exchange, through the –OH contained therein. Organic-matter–clay mineral complexes bonded to the surfaces of clay minerals by replacing the hydroxyl groups with functional groups (carboxyl groups or phenolic hydroxyl groups) contained in the organic matter. Organic–inorganic composites then adsorbed Cu through the coordination exchange of –OH in the polar functional groups of alcohols, phenols, and carboxylic acids. The adsorption capacity of Cu in these three sediment complexes was observed to have the following order: organic–inorganic complex &gt; organic-matter–clay mineral complex &gt; iron-oxide–clay mineral complex. The semi-quantitative analysis results of Fourier Infrared Spectroscopy show that the organic matter (changes in the peak area of functional groups such as carboxyl groups) in the organic-inorganic composite material has an important effect on the amount of copper ions adsorbed by clay minerals.

Iron is an essential nutrient and necessary for biological functions from DNA replication and repair to transcriptional regulation, mitochondrial respiration, electron transfer, oxygen transport, photosynthesis, enzymatic catalysis, and nitrogen fixation. However, due to iron’s propensity to generate toxic radicals which can cause damage to DNA, proteins, and lipids, multiple processes regulate uptake and distribution of iron in living systems. Understanding how intracellular iron metabolism is optimized and how iron is utilized to regulate other intracellular processes is important to our overall understanding of a multitude of biological processes. One of the tools that the cell utilizes to regulate a multitude of functions is ligation of the iron-sulfur (Fe-S) cluster cofactor. Fe-S clusters comprised of iron and inorganic sulfur are ancient components of living matter on earth that are integral for physiological function in all domains of life. Here we will explore the ways in which the cell utilizes Fe-S clusters to sense the intracellular environment and respond to maintain equilibrium.

Non-viral gene carriers because of their limited side effects, biocompatibility, simplicity and taking the advantages of electrostatic interactions have shown noticeable potential in gene delivery. The low transfection rate of non-viral vectors under physiological conditions is a significant issue. Here, the aim of this study was to investigate the efficacy of hydrophilic and hydrophobic groups on gene carriers such as two synthesized amphiphilic polymer of dextran-stearic acid-spermine (DSASP) with verified lipid and amine conjugations that associated with Fe3O4 superparamagnetic nanoparticles to promote the target delivery and decrease the transfection time using static magnetic field. Our findings illustrate that magnetic nanoparticles are spherical with positive surface charges and superparamagnetic behaviors. The DSASP–pDNA/MNPs offered a strong pDNA condensation, protection against DNase degradation, significant cell viability in HEK 293T cells and. Although conjugations of spermine play a critical role in transfection efficiency, amphiphilic polymer with more derivatives of stearic acid showed better transfection yields. Therefore, DSASP amphiphilic magnetic carriers offer new insights for gene delivery due to the amine contents and ameliorate the uptake of complexes via cell membrane based on its hydrophilic surface.

Nanocrystalline silicon oxide (nc-SiOx:H) is a multipurpose material with its varied application in solar cells as a transparent front contact, intermediate reflector, back reflector layer and even tunnel layer for passivating contacts, owing to easy tailoring of its optical properties. In this work, we systematically investigate the influence of gas mixture (SiH4, CO2, PH3 and H2), RF power and process pressure on the optical, structural and passivation properties of thin n-type nc-SiOx:H films prepared in an industrial, high throughput, plasma-enhanced chemical vapor deposition (PECVD) reactor. We provide a detailed description of the n-type nc-SiOx:H material develop-ment using various characterization techniques (SEM, EDX, Raman spectroscopy, and spectro-scopic ellipsometry) with a focus on the relationship between the material properties and the pas-sivation they provide to n-type c-Si wafers characterized by their effective carrier lifetime (τeff). Further, we also outline the parameters to be kept in mind while developing different n-type nc-SiOx:H layers for different solar cell applications. We report a tunable optical gap (1.8 – 2.3 eV) for our n-type nc-SiOx:H films as well as excellent passivation properties with τeff up to 3.5 ms (iVoc ~ 715 mV) before annealing. Oxygen content plays an important role in determining the crystallinity and hence passivation quality of the deposited nanocrystalline silicon oxide films.

In recent decades, the requirements for implantable medical devices increased, but the risks of implant rejection still exist. These issues are primarily associated with poor osseointegration, leading to biofilm formation on the implant surface. This study focuses on addressing these issues by developing a biomaterial for implant coatings. 45S5 Bioglass has been widely used in tissue engineering due to its ability to form a hydroxyapatite layer, ensuring a strong bond between the hard tissue and the bioglass. In this context, 45S5 bioglasses, modified by the incorporation of different amounts of copper oxide, from 0 to 8 mol%, were synthesized by the melt-quenching technique. The incorporation of Cu ions does not show a significant change in the glass structure. Since the bioglass exhibited the capacity of being polarized, and therefore promoting the osseointegration effectiveness, the electrical properties of the prepared samples were studied using the impedance spectroscopy method, in the frequency range of 102-106 Hz and temperature range of 200-400 K. The effects of CuO on charge transport mobility were investigated. Additionally, the bioactivity of the modified bioglasses was evaluated through immersion tests in simulated body fluid. The results revealed the initiation of a Ca-P-rich layer formation on the surface within 24 h, indicating the potential of the bioglasses to enhance the bone regeneration process.

The carbonyl iron particles were dispersed in a polychloroprene rubber (CR) matrix under an external magnetic field for practical application as microwave absorption composites film. The film prepared under external magnetic field with a thickness of only 0.54 mm showed least reflection loss of -15.98 dB and the reflection loss value less than -10.0 dB over the frequency range of 11.4~14.8 GHz. In comparison with the microwave absorption properties of calculation by transmission line theory based on the tested relative complex permittivity and permeability and film prepared by general route without external magnetic field, the film made with external magnetic field exhibited more excellent microwave absorption properties, strongly depending on the increment of anisotropy and rearrangement of magnetic particles. The results indicated the composite film made under external magnetic field have excellent microwave absorption properties, which suggest that the composites thin film could be used as a thinner and lighter microwave absorber.

Sentinel lymph node dissection (sLND) using a magnetometer and superparamagnetic iron oxide nanoparticles (SPIONs) as a tracer was successfully applied in prostate cancer (PCa). Radioisotope-guided sLND combined with extended pelvic LND (ePLND) achieved better node removal, increasing the number of affected nodes or the detection of sentinel lymph nodes outside the established ePLND template. We determined the diagnostic value of additional magnetometer-guided sLND after intraprostatic SPION-injection in high-risk PCa. This retrospective study included 104 high-risk PCa patients (PSA >20 ng/ml and/or Gleason score ≥8 and/or cT2c) from a prospective cohort who underwent radical prostatectomy with magnetometer-guided sLND and ePLND. The diagnostic accuracy of sLND was assessed using ePLND as a reference standard. Lymph node metastases were found in 61 of 104 patients (58.7%). sLND had a 100% diagnostic rate, 96.6% sensitivity, 95.6% specificity, 96.6% positive predictive value, 95.6% negative predictive value, 3.4% false negative rate, and 4.4% false positive rate (detecting lymph node metastases outside the ePLND template). These findings demonstrate the high sensitivity and additional diagnostic value of magnetometer-guided sLND, exceeding that of ePLND through the individualized extension of PLND or the detection of sentinel lymph nodes / lymph node metastases outside the established node template in high-risk PCa.

The paper provides a discussion on the results of studies of the effect exerted by combined degradation factors typical of four types of wear: abrasion, impact-abrasion, tribocorrosion, and impact-abrasion-corrosion, conducted for chain wheels made of Ni-Cu alloyed Austempered Ductile Iron. The studies consisted in determining the content of retained austenite in the structure of the cast irons in question, establishing the measures of wear following wear testing, and identifying basic surface degradation mechanisms observed in the chain wheels tested following multifactorial wear processes. The chain wheels made of ADI were found to have sustained the greatest damage under the impact-abrasion-corrosion (three-factor) wear scenario, while the wear was least advanced in the abrasion (one-factor) wear case. Another observation derived from the studies is that the combined effect of dynamic forces, corrosion, and quartz sand-based abrasives causes increased surface degradation in the cast iron grades taken into consideration compared to processes characterised by a reduced number of degradation factors (i.e. one- or two-factor wear processes). Additional hardness tests and XRD analyses have revealed a distinctive effect attributable to combined degradation factors on the surface hardness increase value and implied that bench testing was followed by phase transition.

CoCrFeNiMn high-entropy alloy coatings were prepared on compacted graphite iron（CGI） through plasma cladding to strength the CGI substrate. The effects of heat treatment temperatures and times on the microstructure and mechanical properties of the CoCrFeNiMn coatings were investigated. After heat treatment, a single FCC phase was remained in the coating as compared to the deposited one, with smaller dendrites, larger dendritic spacing and more Cr-rich compounds precipitated between dendrites. The coatings’ microhardness was increased after heat treatment. After heat treated at 660°C for 90 minutes, the coating had the highest microhardness of 563±6.9 HV0.2, the lowest frictional coefficient of 0.71 and the smallest wear mass loss of 1.12 mg, and it had the best wear resistance.

Several observations have shown that patients with polycythemia have iron deficiency. Our objectives were to report the prevalence of iron deficiency, to evaluate the diagnostic performance of serum ferritin in polycythemia vera and to describe the mechanisms of this association. This is a retrospective descriptive and analytical study carried out in the internal medicine department of the Henri Mondor Hospital, Aurillac, France. The study involved 114 patients with polycythemia, followed in the department from January 1, 2010 to December 31, 2021. To evaluate the diagnostic performance, the JAK2 mutation was considered as the gold standard of diagnosis. Thirty-three patients had polycythemia vera and 76 patients had secondary polycythemia. The mean age of the patients was 61.79 years (±15.44) with a sex ratio of 4.43. The overall prevalence of iron deficiency was 21.05%. The prevalence was 53% in polycythemia vera group and 1.32% in secondary polycythemia group. The risk of iron deficiency was high in polycythemia vera (OR=115; 95% CI [14.4-918.2], p<0.000). The sensitivity and specificity of serum ferritin were 52.63% and 100% respectively. Assessment of iron deficiency should be part of the initial evaluation of polycythemia. The presence of iron deficiency is specific for polycythemia vera.

Targeted radioisotope-guided sentinel lymph node dissection (sLND) has shown high diagnostic accuracy in prostate cancer (PCa). To overcome the downsides of the radioactive tracers, magnetometer-guided sLND using superparamagnetic iron oxide nanoparticles (SPIONs) was successfully applied in PCa. This prospective study (SentiMag Pro II, DRKS00007671) determined the diagnostic accuracy of magnetometer-guided sLND in intermediate- and high-risk PCa. Fifty intermediate- or high-risk PCa patients (PSA≥10 ng/ml and/or Gleason score ≥7; median PSA 10.8 ng/ml, IQR 7.4–19.2 ng/ml) were enrolled. After intraprostatic SPIONs injection a day earlier, patients underwent magnetometer-guided sLND and eLND, followed by radical prostatectomy. SLNs were detected in vivo and in ex vivo samples. Diagnostic accuracy of sLND was assessed using eLND as the reference. SLNs were detected in all patients (detection rate 100%), with 447 SLNs (median 9, IQR 6–12) being identified and 966 LNs (median 18, IQR 15-23) being removed. Thirty-six percent (18/50) of patients had LN metastases (median 2, IQR 1–3). Magnetometer-guided sLND had 100% sensitivity, 97.0% specificity, 94.4% positive predictive value, 100% negative predictive value, 0.0% false negative rate, and 3.0% additional diagnostic value (LN metastases only in SLNs outside the eLND template). In vivo, one positive SLN/LN-positive patient was missed, resulting in a sensitivity of 94.4%. In conclusion, this new magnetic sentinel procedure has high accuracy for nodal staging in intermediate- and high-risk PCa. The reliability of intraoperative SLN detection using this magnetometer system requires verification in further multicentric studies.

Objective: Lower extremity ischemia-reperfusion injury (IRI) may occur with trauma-related vascular injury and various vascular diseases, during the use of a tourniquet, temporary clamping of the aorta in aortic surgery, and acute or bilateral acute femoral artery occlusion. Mitochondrial dysfunction and increased basal oxidative stress in diabetes may cause an increase in the effects of increased reactive oxygen species (ROS) and mitochondrial dysfunction due to IRI. It is of great importance to examine therapeutic approaches that can minimize the effects of IRI, especially for patient groups under chronic oxidative stress. Cerium oxide (CeO2) nanoparticles mimic the antioxidant enzymes and act as a catalyst that scavenges ROS. In this study, it was aimed to investigate whether CeO2 has protective effects on skeletal muscles in lower extremity IRI in mice with streptozocin-induced diabetes. Methods: A total of 38 Swiss albino mice were divided into six groups as follows: control group (group C, n=6), diabetes group (group D, n=8), diabetes-CeO2 (group DCO, n=8), diabetes-ischemia/reperfusion (group DIR, n=8), and diabetes-ischemia/reperfusion-CeO2 (group DIRCO, n=8). DCO and DIRCO groups were given doses of CeO2 0.5mg/kg intraperitoneally 30 minutes before the IR procedure. A 120-minute ischemia-120-minute reperfusion period with 100% O2 was performed. At the end of the reperfusion period, muscle tissues were removed for histopathological and biochemical examinations. Results: Total antioxidant status (TAS) levels were found to be significantly lower in group DIR compared with group D (p=0.047 and p=0.022, respectively). In group DIRCO and total oxidant status (TOS) levels were found to be significantly higher than in group DIR (p

One consequence of the global technological advancement in conventional metallurgy is the fast depletion rate of valuable minerals, which are also becoming increasingly difficult to find in pure and economically viable forms. This has spurred more interest in technologies that investigate ability of different microorganisms to mobilize valuable metals from their ores via diverse metabolic processes. This study was carried out therefore to isolate, identify and characterize iron solubilizing bacteria from Iron stones of Agbaja iron ore mining site of Kogi State, Nigeria. Crushed samples in the range of 0.25µm and 0.75µm particle sizes were cultured in a modified 9k media to facilitate bacterial growth and pure cultures were then isolated and sub-cultured for further bioleaching studies. Morphological and biochemical analysis suggests that some of the bacteria identified are members of Acidithiobacillus spp, Pseudomonas spp, and Leptospirillum spp. Studies conducted on pure cultures and mixed consortium of the identified organisms shows that a mixture of the three organisms leached iron ore to about 96.16%. Also results of growth pattern due to bacteria countafter 24-72hours of incubation ranged between 0.1×10³ cfu/ml and 12.3 ×10³ cfu/ml for Acidithiobacillus spp. The need to explore the molecular characteristics of these organisms with a view to generating more information on the quality/quantity of their DNA for future cloning activities was also investigated in this work. DNA was extracted using zymo fungal/bacterial extraction mini prep kit ^TM (cat #6001) and subsequently subjected to 1% agarose gel electrophoresis. Visible bands were obtained with Alpha Innotech Gel Documentation Machine. DNA amplification was carried out using a pettier based thermo cycler PCR machine and electrophoresed on 1.5% agarose gel. Results of the PCR shows a visible band corresponding to 1.5kbp using this primer 27F (5¹-GAGTTTGATCCTGGCTCAG-3¹) and 1492R (5^1-GGTTACCTTGTTACGACT-3¹). DNA purity check shows two of the bacteria possess very good qualities for sequencing for further molecular analysis.

Combining modern thermodynamics theory branches, including finite time thermodynamics or entropy generation minimization, constructal theory and entransy theory, with metallurgical process engineering, this paper provides a new exploration on generalized thermodynamic optimization theory for iron and steel production processes. The theoretical core is to thermodynamically optimize performances of elemental packages, working procedure modules, functional subsystems, and whole process of iron and steel production processes with real finite-resource and/or finite-size constraints with various irreversibilities toward saving energy, decreasing consumption, reducing emission and increasing yield, and to achieve the comprehensive coordination among the material flow, energy flow and environment of the hierarchical process systems. A series of application cases of the theory are reviewed. It can provide a new angle of view for the iron and steel production processes from thermodynamics, and can also provide some guidelines for other process industries.

Iron and zinc are essential micronutrients required for growth and health. Deficiencies of these nutrients are highly prevalent among populations, but can be alleviated by supplementation. Cross-sectional studies in humans showed positive association of serum zinc levels with hemoglobin and markers of iron status. Dietary restriction of zinc or intestinal specific conditional knock out of ZIP4 (SLC39A4), an intestinal zinc transporter, in experimental animals demonstrated iron deficiency anemia and tissue iron accumulation. Similarly increased iron accumulation has been observed in cultured cells exposed to zinc deficient media. These results together suggest a potential role of zinc in modulating whole body iron metabolism. Studies in intestinal cell culture models demonstrate that zinc induces iron uptake and transcellular transport via induction of divalent metal iron transporter-1 (DMT1) and ferroportin (FPN) expression, respectively. It is interesting to note that intestinal cells are exposed to very high levels of zinc through pancreatic secretions, which is a major route of zinc excretion from the body. Therefore, zinc appears to be modulating the iron metabolism possibly via regulating the DMT1 and FPN1 levels. Herein we critically reviewed the available evidence to hypothesize novel mechanism of Zinc-DMT1/FPN axis in regulating intestinal iron absorption and tissue iron accumulation to facilitate future research aimed at understanding the yet elusive mechanisms of iron and zinc interactions.

(1) Background: Ulcerative colitis (UC) is characterized by immune system dysregulation with frequent extraintestinal manifestations, including airways involvement. Reduction in CO diffusing capacity and functional alterations in small airways have been described. The extended analysis of Fractional Exhaled Nitric Oxide (FeNO), may distinguish the sites of production and the presence of small airways inflammation being a useful, non-invasive marker for these patient’s follow up. The aim of our study was to compare PFTs, FeNO and CANO values of UC patients with different clinical disease activity and healthy subjects to reveal lung function abnormalities and the presence of subclinical airway inflammation. (2) Methods: We enrolled 42 adult outpatients with different clinical activity stages of UC (mean age 39±13 years) and a healthy control group of 41 subjects (mean age 29±3 years). C-reactive protein (CRP) and FeNO values at different flows (50,100 and 200 ml/sec) were collected. All patients performed pulmonary function tests (PFT’s) with static volumes and diffusing capacity (DLCO). (3) Results: FENO, CANO and CRP values were significantly increased in UC patients when compared with controls (p=0.02 and p&lt;0.0001, respectively) and proportionally to the disease activity (FeNO class 3: 27.1 ppb vs class 1-2: 6.2 ppb; CANO values class 3: 8.1 ppb vs class 1-2: 2.0 ppb (p &lt; 0.0001). TLC and DLCO were significantly reduced in UC patients compared to controls (p=0.011 and p&lt;0.0001, respectively). (4) The results of this study show significant lung functional abnormalities in UC patients and suggest the presence of airway inflammation directly correlated with the disease activity suggesting an integrated approach in routine assessment.

Sideroflexins (SLC56 family) are highly conserved multi-spanning transmembrane proteins inserted in the inner mitochondrial membrane in eukaryotes. Few data are available on their molecular function but, since their first description, they were thought to be metabolite transporters probably required for iron utilization inside the mitochondrion. Such as numerous mitochondrial transporters, sideroflexins remain poorly characterized. The prototypic member SFXN1 has been recently identified as the previously unknown mitochondrial transporter of serine. Nevertheless, pending questions on the molecular function of sideroflexins remain unsolved, especially their link with iron metabolism. Here, we review the current knowledge on sideroflexins, their presumed mitochondrial functions and the sparse - but growing - evidence linking sideroflexins to iron homeostasis and iron-sulfur cluster biogenesis. Since an imbalance in iron homeostasis can be detrimental at the cellular and organismal levels, we also investigate the relationship between sideroflexins, iron and physiological disorders. Investigating Sideroflexins’ functions constitutes an emerging research field of great interest and will certainly lead to main discoveries on mitochondrial physiopathology.

Iron is the most abundant micronutrient in plant mitochondria and it has a crucial role in biochemical reactions involving electron transfer. It has been described in Oryza sativa that Mitochondrial Iron Transporter (MIT) is an essential gene and that knockdown mutant rice plants have a decreased amount of iron in mitochondria, strongly suggesting that OsMIT is involved in mitochondrial iron uptake. In Arabidopsis thaliana, two genes encode MIT homologues. In this study, we analyzed different AtMIT1 and AtMIT2 mutant alleles, confirming that individually AtMIT1 nor AtMIT2 genes are essential. When we generated crosses between Atmit1 and Atmit2 alleles we were able to isolate homozygous double mutant plants. Interestingly, homozygous double mutant plants were obtained only when mutant alleles of Atmit2 with the T-DNA insertion in the intron region were used for crossings, and in these cases a correctly spliced AtMIT2 mRNA was generated, although at a low level. Atmit1 Atmit2 double homozygous mutant plants, which were knockout for AtMIT1 and knockdown for AtMIT2, were grown and chacterised in iron sufficient conditions. Pleiotropic developmental defects were observed including abnormal seeds, increased number of cotyledons, slow growth rate, pinoid stems, defects in flower structures and reduced seed set. We observed a possible phenomenon of T-DNA suppression in the next generation of Atmit1 Atmit2 double homozygous mutant plants, correlating with an increased splicing of the AtMIT2 intron containing the T-DNA. Molecular analysis of gene expression markers for mitochondrial and oxidative stress showed that Atmit1 Atmit2 double homozygous mutant plants express a degree of mitochondrial perturbation. A RNA-Seq study was performed and we could identify more than 760 genes differentially expressed in Atmit1 Atmit2, including genes involved in iron transport, coumarin metabolism, and hormones metabolism, transport and signaling. Our data suggest that some of the phenotypes observed in Atmit1 Atmit2 double homozygous mutant plants are mediated by defects in auxin homeostasis.

The dynamic equilibrium of iron homeostasis has an important role in sustaining metabolic and neurological functions during human life. Iron excretion is modest and unregulated hence this overall equilibrium is tightly regulated in normal conditions by increasing deficient or limiting excessive iron assimilation. Here we focus on neural tissue overload, dyshomeostasis that is preceded by excessive assimilation, disturbances in internal homeostasis or both. Normal steps in iron homeostasis include its uptake across the apical membrane of the enterocytes in a mildly acidic duodenal milieu by the major importer of ferrous iron, Divalent Metal Transporter 1 (DMT1) (Nramp2/DCT1/SLC11A2, solute carrier family 11 member 2) [1, 2], responsible for the uptake of Non-Transferrin Bound Iron (NTBI) and divalent metals [3], passage through enterocytes bound to a chaperone and crossing the basal membrane via the only known cellular ferrous iron exporter, ferroportin [4] with the iron bound to transferrin (Tf) as it exits. Cells in peripheral tissues largely utilize circulating iron after uptake by receptor-mediated endocytosis of Tf-bound Iron [5]. Derangement of duodenal NTBI absorption of iron and heavy metals is influenced by systemic iron metabolism associated with inflammation that leads to iron accumulation into peripheral tissues and potential development of neurodegenerative diseases, involving distribution and fine regulation of DMT1 also in the central nervous system, where inflammatory-related acidosis influences DMT1 uptake, via its action as a proton cotransporter. Pharmacological strategies to inhibit NTBI transport selectively will be illustrated in relationship to protection, particularly neuroprotection, against iron overload associated with acidosis, inflammation, neuroinflammation and subsequent neurodegeneration.

Hypertensive diseases of pregnancy (HDP) represent a global clinical challenge, affecting 5-10% of women and leading to complications for both maternal well-being and fetal development. At the heart of these complications is endothelial dysfunction, with oxidative stress emerging as a pivotal causative factor. The reduction in nitric oxide (NO) bioavailability is a vital indicator of this dysfunction, culminating in blood pressure dysregulation. In the therapeutic context, although antihypertensive medications are commonly used, they come with inherent concerns related to maternal-fetal safety, and a percentage of women do not respond to these therapies. Therefore, alternative strategies that directly address the pathophysiology of HDP are required. This article focuses on the potential of the nitrate-nitrite-NO pathway, abundantly present in dark leafy greens and beetroot, as an alternative approach to treating HDP. The objective of this review is to discuss the prospective antioxidant role of nitrate. We hope our discussion paves the way for using nitrate to improve endothelial dysfunction and control oxidative stress, offering a potential therapy for managing HDP.

Antarctic krill protein-iron complex and peptide-iron complex were obtained to investigate their iron bioavailability, expression of iron-regulated genes, and in vivo antioxidant capacity. Results indicated that Antarctic krill peptide-iron complex increased significantly the hemoglobin (Hb), serum iron (SI) and iron content in the liver and spleen in iron-deficiency anemia (IDA) mice (P < 0.05) compared with those of Antarctic krill protein-iron complex. Despite the gene expressions of divalent metal transporter 1(DMT1), transferrin (Tf) and transferrin receptor (TfR) could be better regulated by both Antarctic krill peptide-iron complex and protein-iron complex, the relative iron bioavailability of the Antarctic krill peptide-iron complex group (152.53±21.05%) was significantly higher than that of the protein-iron complex group (112.75±9.60%) (P<0.05). Moreover, Antarctic krill peptide-iron complex could enhance the antioxidant enzyme activities of superoxidase dismutase (SOD) and glutathione peroxidase (GSH-Px), reduce the malondialdehyde (MDA) level in IDA mice compared with the protein-iron complex, reducing the cell damage caused by IDA. Therefore, these results demonstrated that Antarctic krill peptide-iron complex could be used as a highly efficient and multifunctional iron supplement.

Mn-promoted bulk iron catalysts with high specific surface area (82-211 m2.g-1) were synthesized by coprecipitation followed by drying under supercritical conditions. The catalysts were tested in the CO2 hydrogenation reaction. The Mn-promoted iron catalysts showed better textural properties than the bare Fe2O3 catalyst, allowing better dispersion of the active phase, easier reduction of iron oxide, better carburization of iron oxides and higher catalytic activity than the bare Fe2O3 catalyst. The best activity results were obtained by catalyst promotion with a very low amount of Mn (Mn/Fe ratio of 0.05). Upon steady-state conditions (T=340 ºC, total pressure of 20 bar and H2/CO2=3), this catalyst showed high CO2 conversion (44.2%) and selectivity to C2-C4 hydrocarbons (68%, olefin to paraffin ratio of 0.54), while the selectivity to C5+ hydrocarbons, CH4 and CO was about 3.2, 38.5 and 5%, respectively. A close correlation was found between catalyst textural properties and CO2 conversion. The most active MnFe-0.05 catalyst shows high stability during 72 h of reaction related to low amount of soft coke formation and catalyst activation through the formation of χ-Fe5C2 phase during the on-stream reaction.

In pigs, iron deficiency anemia (IDA) is the most prevalent deficiency disorder during the early postnatal period frequently developing into a critical illness. Meanwhile, in humans, only low-birth-weight infants, including premature infants are especially susceptible to developing IDA. In both human and pig neonates, the initial cause of IDA is low birth iron stores. In piglets this shortage of stored iron results mainly from genetic selection over the past few decades for large litter size and high birth weight. In consequence, pregnant sows cannot provide sufficient amount of iron to the increasing number of developing fetuses. Supplementation with iron is a common practice for the treatment of IDA in piglets. For decades, the preferred procedure for delivering iron supplements during early life stages has been through the intramuscular injection of large amount of iron dextran. However, this relatively simple therapy, which in general, efficiently corrects IDA, may generate toxic effects, and by inducing hepcidin expression, may decrease bioavailability of supplemental iron. New iron supplements are considered now with the aim to combine improvement of hematological status, blunting hepcidin expression, and minimizing toxicity of the administered iron. We propose that iron-deficient piglets constitute a convenient animal model for performing pre-clinical studies with iron supplements.

Dietary iron assimilation is critical for health and essential to prevent iron deficient states and related comorbidities, such as anemia. The bioavailability of iron is limited, while its absorption and metabolism are tightly controlled to keep body iron stores within a relatively narrow range. Genetic inactivation of the iron hormone hepcidin causes hereditary hemochromatosis, an endocrine disorder of iron overload characterized by chronic hyperabsorption of dietary iron, with deleterious clinical complications if untreated. The impact of high dietary iron intake and elevated body iron stores in the general population is not well understood. Herein, we summarize epidemiological data suggesting that high intake of heme iron, which is abundant in meat products, poses a risk factor for metabolic syndrome pathologies, cardiovascular diseases, and some cancers. We discuss clinical relevance and potential limitations of data from cohort studies, as well as the need to establish causality and elucidate molecular mechanisms.

Hereditary hemochromatosis (HH) is the main genetic cause of iron overload and is regarded as metal-related human toxicosis. HH may result from HFE and non-HFE gene mutations causing hepcidin deficiency or hepcidin resistance. The disorder has a high biochemical penetrance, but a low clinical prevalence. Unfortunately, the majority of patients with HH remain undiagnosed at their disease-curable stage. The main aim of HH therapy is to prevent iron overload in the early-phase disease and elimination of excess iron from the body by phlebotomy in its late stage. Raising global awareness of HH among health professionals, their training to pay attention to early HH signs and symptoms, and strict patient monitoring are critical management strategies for preventing treatment delays, upgrading its efficacy, and improving patient prognosis.

In eutrophic waters, such as Mikawa Bay, Japan, anoxic bottom water develops in summer. This causes sulfide release into seawater by sulfate reduction in the sediment, leading to environmental problems. The addition of iron to sediments is a method used to improve the sediment environment, which was devised from a natural phenomenon. However, this method has not yet been quantitatively evaluated. In this study, we aim to quantitatively evaluate the suppressive effect of iron on sulfide release. First, we develop a sediment model that focuses on S and Fe. We then attempted to reproduce the observations and experiments on sulfide dynamics using the model. Consequently, the proposed model was able to reproduce field sulfur and Fe dynamics in sediments. Additionally, the model described the characteristics of sulfide release considering the effects of additive iron materials. Finally, we conducted predictive calculations and quantitatively evaluated the effects of adding iron materials to the sediments in terms of sulfur and iron cycles.

Our environment has been significantly impacted by man-made pollutants, primarily due to industries make substantial use of synthetic chemicals, resulting in significant environmental consequences. In this research investigation, the co-precipitation approach was employed for the synthesis of cellulose-based ferric oxide (Fe₂O₃/cellulose) and copper oxide nanoparticles (CuOx-NPs). Scanning electron microscopy (SEM) analyses were conducted to determine the properties of the newly synthesised nanoparticles. Furthermore, the synthesized nanoparticles were employed for eliminating chromium from aqueous media under various conditions, including temperature, contact time, adsorbent concentration, adsorbate concentration, and pH. Additionally, the synthesised materials were used to recover Cr(VI) ions from real samples, including tap water, seawater, and industrial water, and the adsorptive capacity of both materials evaluated under optimal conditions. The synthesis of Fe₂O₃/cellulose and CuOx-NPs proved to be effective, as indicated by the outcomes of the study.

Two Iron Age settlements, Tuzusai and Taldy Bulak 2 (ca. 500 BCE to 1 CE), located in Southeastern Kazakhstan on the Talgar alluvial fan north of the Tian Shan range, have yielded a small collection of bone, antler/horn, bronze, and stone artifacts with affinity to nomadic art of the first millennium BCE. Both settlements date within the period of late Saka culture. Two pieces have decorative ornamentations with zoomorphic imagery: a small carved fragment of a with carved images of a wing and an ear and a perforated bone disk with the carving of three birds’ heads. The other artifacts include objects associated with Saka weaponry or nomadic economy such as the two antler/horn psalia (cheek pieces) and a bronze amulet. A carnelian bead will also be described as an imported object. These special finds are found on the occupation floors of mud brick houses and pit houses of settlements, not in grave or burial contexts. The objects are placed in stratigraphic sequence in the settlement sites. Then the method for placing these objects within the chronological framework of “animal-style art” is through comparisons with similar objects found throughout Eurasia—a method used in Soviet and Post-Soviet archaeology. The results show that functional and stylistic elements of the six objects indicate that the Talgar settlements were part of a larger world-system of trade and communication along the early Silk Route(s).

Nitric oxide (NO) is synthesized and is involved in various physiological and developmental process regulation in all kingdoms of life. Fungi have been less explored in terms of endogenous NO biology than mammals, plants, and bacteria. In this review, we summarize and discuss the studies to date on intracellular NO biosynthesis and function in fungi. Two mechanisms for NO biosynthesis, NO synthase (NOS)-mediated arginine oxidation, and nitrate and nitrite reductase-mediated nitrite reduction, are most frequently reported. Furthermore, we summarize the multifaceted functions of NO in fungi, as well as its role as a signaling molecule in fungal growth regulation, development, abiotic stress, virulence regulation, and metabolism. Finally, we present potential directions for future research on fungal NO biology.

Abstract— In this paper, degradation effects such as the self-heating effect and the DIBL effect in 2D-MoS2-based MOSFETs are investigated through simulations. These are transistors with Al2O3 and HfO2 as the gate oxide and SiO2 and HfO2 as the back oxide (BOX). The self-heating effect (SHE) is simulated using the thermodynamic transport model. The dependence of the DIBL effect (Drain Induced Barrier Lowering) and the lattice temperature in the center of the channel on the gate length for transistors with different gate oxide and BOX materials is considered. Transistors are considered where the channel is fully and partially (just below the gate) covered by gate oxide. It is shown that the transistors with Al2O3 as gate oxide and SiO2 as BOX materials have higher immunity to DIBL effect and transistors with HfO2 as gate oxide and HfO2 as BOX materials have higher immunity to SHE.

MgAl oxide coatings containing MgO and MgAl2O4 phases were doped with CeO2 particles using plasma electrolytic oxidation (PEO) of AZ31 magnesium alloy in 5 g/L NaAlO2 water solution, with CeO2 particles added at concentrations up to 8 g/L. They underwent extensive inve-stigation into their morphology, chemical and phase compositions, and most importantly, photoluminescent (PL) properties and photocatalytic-activity (PA) in photodegradation of methyl orange (10 cm3 of 8 mg/L). The concentration of CeO2 particles in the aluminate electrolyte influences the amount of CeO2 particles incorporated into MgAl oxide coatings, but CeO2 particles have no signi-ficant effect on the surface morphology, thickness, or phase structure of the coatings. The PL emi- ssion spectrum of MgAl oxide coating is divided into two bands: one in the 350-600 nm range related to structural defects in MgO, and another much more intense in the 600-775 nm range attributed to F+ centres in MgAl2O4. Incorporated CeO2 particles do not have a significant effect on the PL intensity of the band in the red spectral region, but the PL intensity of the first band increases with the concentration of CeO2 particles. PA of MgAl/CeO2 oxide coatings is higher than that of pure MgAl oxide coatings. The highest PA was observed for MgAl/CeO2 oxide coatings formed in aluminate electrolytes with the addition of 2 g/L of CeO2 particles. The MgAl/CeO2 oxide coatings remained chemically and physically stable across multiple cycles, indicating their potential for applications.

Iron deficiency (ID) is by far the most common nutritional disorder in developing and developed countries. When left untreated, ID leads to anemia. Although the usual recommended treatment for iron deficiency anemia (IDA) is oral iron therapy with countless products, such therapy necessitates administration for &gt;3-6 months with questionable patient compliance since most oral iron products have an unpleasant metallic aftertaste and cause intestinal side effects. In addition, in certain gastrointestinal conditions, such as inflammatory bowel diseases or untreated gluten-sensitive enteropathy, oral iron therapy is contraindicated or unsuccessful. Intravenous iron is considered safe in adults, where adverse events are mild and easily managed. The experience with parenteral iron in children is much more limited and many pediatricians appear reluctant to use it because of uncorroborated fears of serious anaphylactic reactions. In the current article, we thoroughly review the available pediatric literature on the use of all commercially available parenteral iron products except ferumoxytol, which was recently removed from the market. We conclude that parenteral iron appears to be safe in children, it works faster than oral iron and the newer third-generation products allow replacement of the total iron deficit at a single setting.

Oral ferric citrate hydrate (FCH) is effective for iron deficiency in hemodialysis patients.; however, it remains unclear how iron balance in the body affects iron absorption from the intestinal tract. This prospective, observational study (Riona-Oral Iron Absorption Trial, R-OIAT, UMIN 000031406), conducted at 42 hemodialysis centers in Japan, wherein 268 hemodialysis patients without inflammation were enrolled and treated with a fixed amount of FCH for 6 months. We assessed the predictive value of hepcidin-25 for iron absorption and iron shift between ferritin (FTN) and red blood cells (RBCs) following FCH therapy. Serum iron changes at 2 h (ΔFe2h) after FCH ingestion were evaluated as iron absorption. The primary outcome was the quantitative delineation of iron variables on ΔFe2h and the secondary outcome was the description of the predictors of body iron balance. Generalized estimating equations (GEE) were used to identify the determinants of iron absorption during each phase of FCH treatment. ΔFe2h increased when hepcidin-25 and MCH decreased (-0.155, -0.242 to -0.068, p = 0.001; -2.574, -4.421 to -0.726, p = 0.006, respectively) in GEE. Hepcidin-25 increased when erythropoiesis-stimulating agent (ESA) decreased (-0.002, -0.002 to -0.001, p=0.000). FTN increased when RBC and ESA decreased (-0.466, -0.605 to -0.327, p=0.000; -0.002, -0.004 to -0.000, p=0.05, respectively. Limiting erythropoiesis to maintain hemoglobin levels induces RBC reduction in hemodialysis patients, resulting in increased hepcidin-25 and FTN levels. Hepcidin-25 production may prompt an iron shift from RBC-iron to FTN-iron, inhibiting iron absorption even with continued FCH intake.

Individual susceptibility to pulmonary oxygen toxicity (PO2tox) is highly variable and currently lacks a reliable biomarker for predicting pulmonary hyperoxic stress. As nitric oxide (NO) is involved in many respiratory system processes and functions, we aimed to determine if expired nitric oxide (FENO) levels can provide an indication of PO2tox susceptibility in humans. Eight U.S. Navy trained divers volunteered as subjects. The hyperoxic exposures consisted of six- and eight-hour hyperbaric chamber dives conducted on consecutive days in which subjects breathed 100% oxygen at 202.65 kPa. Subjects’ individual variability in pulmonary function and FENO was measured twice daily over five days and compared with their post-dive values to assess susceptibility to PO2tox. Only subjects who showed no decrements in pulmonary function following the six-hour exposure conducted the eight-hour dive. FENO decreased by 55% immediately following the six-hour oxygen exposure (n=8, p<0.0001) and by 63% following the eight-hour exposure (n=4, p<0.0001). Four subjects showed significant decreases in pulmonary function immediately following the six-hour exposure. These subjects had the lowest baseline FENO and the lowest post-dive FENO and had clinical symptoms of PO2tox. Individuals with low FENO were the first to develop PO2tox symptoms and deficits in pulmonary function from the hyperoxic exposures. These data suggest that endogenous levels of NO in the lung may protect against the development of PO2tox.

In recent years, the nanoparticles applications have been well recognized in various fields. It is known that nanoparticles as an active ingredient in sunscreens are widely used. Zinc oxide and titanium oxide nanoparticles are common nanoparticles utilized in sunscreens. In this study, we aimed to suggest new nanoparticles for this purpose. Cerium oxide nanoparticles (CeO2-NPs) were synthesized by using Musa sapientum fruit peel extract. Synthesized nanoparticles were identified through Raman, Powder X-ray Diffraction (PXRD), Fourier Transform Infrared spectroscopy (FT-IR), Field Energy Scanning Electron Microscopy (FESEM) and Energy-Dispersive Spectroscopy (EDX). The results showed that size of synthesized nanoparticles are in range 4-13 nm. The cytotoxic activity of synthesized nanoparticles on lung (A549) cancer cell line was performed through MTT assay. The results showed that synthesized nanoparticles are non-toxicity against A549 cell line to below 500 μg/mL of nanoparticles concentration. The Sun protection factor (SPF) was estimated ~ 40 for synthesized CeO2-NPs. So, synthesized nanoparticles can be a good option for use in the cosmetics industry.

Ghrelin and obestatin, two antagonist peptide hormones, are purportedly involved in stimulating appetite and controlling energy balance in humans. Serum ghrelin level is also associated with iron deficiency anemia (IDA), but no study has yet been made of the obestatin level in patients with IDA, even though both hormones are a single gene product. Therefore, the purpose of this investigation is to see whether there is a link between IDA and these two hormones among other hematological parameters in patients with IDA. To measure ghrelin and obestatin, human saliva and serum were collected from 30 women with IDA, aged 31.7 ± 10.7 years, and 30 control women, aged 30.2 ± 8.0 years, with repeated collection of samples over a period of 1 week and 1 month. Saliva and serum ghrelin levels were measured by ELISA. Serum hemoglobin, ferritin, hematocrit and total iron-binding capacity (TIBC) values were determined with an Olympus AU2700. Saliva and serum ghrelin and obestatin levels were significantly lower in the IDA group compared with controls; these levels increased slightly above baseline with iron treatment, but remained below the control values. Furthermore, and as expected, serum hemoglobin, ferritin, and hematocrit levels were significantly increased with iron treatment, while total iron-binding capacity decreased compared to baseline concentrations. The findings suggest that IDA might be linked to imbalance of circulating (serum) and non-circulating (saliva) ghrelin and obestatin levels. Decreased ghrelin and obestatin might destroy iron homeostasis through its effect on intestinal absorption. Measuring these hormone levels might be useful for monitoring the response to iron treatment. Also, serum and saliva levels for both hormones were well correlated. Thus, using saliva in place of serum for monitoring the two hormones should minimize inconvenience and patient discomfort.

Abstract: The aim of this study was to find out the incidence of anemia in pregnant women of Swat District; to analyze the iron variations and its dietary effects.Data were collected during the periods of January – September 2016. The study of samples comprised of 250 pregnant women in the different trimester. Blood sample from each woman was collected and full blood count (FBC) was conducted through Mindray BC-3000 plus hem analyzer for all pregnant individuals. Confirmed anemic cases were then examined for IDA with serum ferritin, serum iron, total iron binding capacity (TIBC) through Randox kit and serum transferrin saturation was estimated by formula (serum ferritin saturation =serum iron ×100/TIBC). The total number of participants in the first trimester were 50, among them 26 women were suffer from iron deficiency anemia (IDA) with 52% weightage of prevalence rate, (mean Hb concentration 9.602 ± 0.87 g/dl). The rates of IDA were 63.3%; ( mean Hb concentration 8.48 ± 1.24 g/dl) and 54%; ( mean Hb concentration 9.18 ± 1.28 g/dl), among 150 and 50 participants in the second and third trimester, respectively. A significant correlation was found between serum ferritin and Hb, serum ferritin against MCV and serum ferritin against MCH. The high prevalence of anemia was found 78.2% in the age group from 26-30 followed by 78.2% in the age group 36-40 years compared to those of other age groups in the second trimester. In this study the prevalence of IDA in third trimester is lower compared to first and second trimester.

Inflammation is an underlying problem for many disease states and has been implicated in iron deficiency (ID). This study aimed to determine whether iron status is improved by epigallocate-chin-3-gallate (EGCG) through reducing inflammation. Thirty-two male Sprague-Dawley rats were randomly divided into four groups (n = 8 each): positive controls, negative controls, lipo-polysaccharide (LPS, 0.5 mg/kg body weight), and LPS + EGCG (LPS plus 600 mg EGCG/kg diet). Iron status, hepcidin, C - reactive protein (CRP), serum amyloid A (SAA), and interleukin-6 (IL-6) were measured. There were no differences in treatment groups compared with control in CRP, hepcidin, and liver iron concentrations. Serum iron concentrations were significantly lower in the LPS (p=0.02) and the LPS+EGCG (p=0.01) than in the positive control group. Compared to the positive control group, spleen iron concentrations were significantly lower in the negative con-trol (p<0.001) but not with both LPS groups. SAA concentrations were significantly lower in LPS + EGCG group compared to LPS alone group. IL-6 concentrations were significantly higher in LPS+EGCG (p= 0.004) than in any of the three groups. EGCG reduced SAA concentrations but did not affect hepcidin or improve serum iron concentration or other iron markers.

Two billion people worldwide suffer from anemia with reproductive-age women being disproportionately affected. Iron plays a crucial role in cellular function and impacts cognition, physical function, and quality of life. Iron deficiency (ID) and iron deficiency anemia (IDA) are associated with adverse effects on pregnancy and fetal development. Oral iron supplementation has been the standard treatment for IDA for decades often producing sub-optimal outcomes. Many babies are still being born with ID and suffer adverse sequelae due to inadequate iron levels in the mothers. Is it time to consider broad scale-up of parenteral iron as a new standard of care?

Recently, resistive random access memory (RRAM) has been an outstanding candidate among various emerging nonvolatile memories for high density storage and in-memory computing applications. However, the traditional RRAM, which accommodates two states depending on applied voltage, cannot meet the high density requirement in the era of big data. Many research groups have demonstrated that RRAM possesses the possibility of multi-level cell to overcome the demand of mass storage. Among numerous semiconductor materials, gallium oxide, as the fourth-generation semiconductor material, is highly-profile due to its excellent material proper-ties, and already be widely used in optoelectronics, high-power, resistive switching device and so on, due to its wide bandgap and transparent properties. In this study, we have successfully demonstrated the Al/GO/Ga2O3/ITO RRAM to achieve the possibility of two-bit storage. Compared to the single-layer counterpart, the bilayer structure has excellent electrical properties and stable reliability. The endurance characteristics could be enhanced above 100 switching cycles with an ON/OFF ratio of over 103. Moreover, the filament models are also described in this thesis to clarify the transport mechanisms.

Thalassemia treatment still relies on supportive care, including mainly blood transfusion and iron chelation therapy. Iron chelation therapy is considered the main responsible factor for the marked improvement in survival of thalassemic patients. Hemosiderosis should be prevented with appropriate chelation therapy from early childhood, timely dose adjustment according to changing body weight, as well as close monitoring of organ iron overload. Three iron chelators are currently available and the choice of appropriate chelator or their combination in pediatric population is individualized, depending on iron overload in target organs, patient age, adverse events and compliance issues, due to the limitations in their administration.

Iron (Fe) deficiency specifically is the most common nutritional disorder due to insufficient absorbable Fe. Biofortification is a process of enriching the nutrient content of staple crops and is considered as a sustainable and cost-effective strategy to address micronutrient deficiency problems especially in the less developed countries. Chickpea (Cicer arietinum L.) is a staple food in many developing countries worldwide and is an excellent source of micronutrients. Biofortification of chickpea is a possible solution to address Fe deficiency problem. Chickpea biofortification experiment was conducted under field conditions to evaluate the effects of different doses of Fe fertilizer (0 kg ha-1,10 kg ha-1 and 30 kg ha-1 of Fe-EDDHA) on Fe content in seeds of 18 chickpea cultivars. The experiment was designed as a factorial combination of 18 chickpea cultivars and 3 different doses in a randomized complete block design with 4 replications at two locations in Saskatchewan in 2015 and 2016. Fe concentration in seeds across 18 different chickpea cultivars increased with Fe fertilization. Fe concentration in X05TH20-2 and CDC Frontier cultivars increased from 57 ppm to 59 ppm and 56 ppm to 58 ppm, respectively, after adding Fe fertilizer in both location in 2015 and 2016.

As a derivative of graphene, graphene oxide (GO) was initially developed by chemists to emulate some of the key properties of graphene, but it was soon recognized as a unique material in its own right, addressing an application space that is not accessible to chemical vapor deposition based materials. Over the past decade, GO has emerged as a new frontier material with tremendous advances in its material fabrication and quality control over its properties. These in turn have led to rapid progress in GO based photonics, electronics, and optoelectronics concepts and devices, evoking new science and paving the way for many technological breakthroughs with exceptional performance. Here, we review the unique fundamental characteristics of GO, its thin film fabrication methods, patterning techniques, and mechanisms for tuning its material properties. This latter capability in particular has enabled novel advanced functional photonic, electronic, and optoelectronic devices. Understanding these insights is essential for designing and tailoring GO properties for state-of-the-art applications including solar energy harvesting, energy storage, medical diagnosis, image displays, and optical communications. We conclude by discussing the open challenges and exciting opportunities of this field, together with future prospects for major technological advancements and breakthroughs.

Background:Boom in nanotechnology in current era has sketched unforeseen transformations in number of fields, such as medicine, health care, food, space, agriculture, etc. The synthesis of nanoparticles with different chemical compositions, sizes, shapes and controlled disparities is an important area of research in this field. Over the last decade, the biosynthesis of metal nanoparticles has received considerable attention due to their unusual and fascinating properties, with various applications, over their bulk counterparts.Hypothesis: The nanoparticle can have huge application in the field of food, pharmaceutical, and cosmetic industries and thus become a major area of research. Green synthesis of zinc oxide nanoparticles (ZnO NPs) using plant extracts offers an eco-friendly and promising substitute to the conventional methods of chemical synthesis. Conclusion: In the arena of nanoparticle phytosynthesis, novel materials have been produced that are eco-friendly, cost-effective and stable. In the current situation, nanotechnology inspires progress in all spheres of life, and therefore the phytosynthetic path of nanoparticle synthesis has emerged as a safe and best alternative to conventional methods. This review summarizes the recent work in the field of zinc nanoparticle phytosynthesis and critically discusses the mechanism proposed behind it.

Graphene-oxide (G) was prepared by the Hummers’ method. A G-COOH layer was synthesised using chloroacetic acid and G. To fabricate carboxylated graphene-RuO2 (G-COORu) nano¬¬-composites, RuO2 nano particles were grown on graphene layers using a one-step thermal method, -COOH(G-COOH), and RuCl3. All materials were characterised using X-ray diffraction, transmission electron microscopy, scanning electron microscopy, 13C-nuclear magnetic resonance as well as X-ray photoelectron, Fourier-transform infrared spectroscopy, and Raman. The electrochemical characteristics of the G-COORu supercapacitors were analysed using electrochemical impedance spectroscopy, cyclic voltammetry, constant current charge–discharge tests, and Nyquist impedance plots. The supercapacitors exhibit a specific capacitance of ~125 F g-1 at 100 mA cm-2 within the potential range of 0–1.0 V. The method used here provides a simple approach for the deposition of RuO2 nano particles on graphene layers and can be widened to the fabrication of other classes of hybrids based on G layers for specific technical applications.

Summary: PURPOSE. Development of a drainless energy-saving technology for the processing of high-moisture iron-containing sludge from metallurgical production. RESEARCH METHOD. The regularities of the combined process of chemical dehydration of high-moisture iron-containing sludge by powdered waste of lime and dolomite, hardening and agglomeration by pressing in a single technological cycle on the developed experimental plant were studied. In the course of laboratory studies, the temperature of the mass, the rate of dehydration, the chemical composition of the mixtures, the appearance of the resulting briquettes, the weight loss during agglomeration-humidity of the mixtures, and mechanical strength of the briquettes were measured. RESULTS. New patterns have been established that have made it possible to develop a nonfiring method for producing iron-containing materials and self-healing briquettes. The essence of his method, which is one of the main provisions of scientific novel provisions, is to combine dehydration and self-hardening of the mixture with the process of shaping by applying external pressure to the hardening mixture in molds to obtain agglomerated material in the form of briquettes in a single technological cycle. The proposed technology does not require drying or firing, and a set of strength properties occurs as the material is cooled in air during the day. A new energy-efficient and drainless method for the production of iron-containing briquettes has been developed, which combines the processes of chemical dehydration and agglomeration in one technological cycle. CONCLUSION. The proposed project and technology will allow organization of production for the processing of high-moisture iron-containing sludge and the production a complex iron-containing material as a secondary metal-containing raw material for metallurgical plants for the production of steel and rolled metal. and dolomite dust from dry gas cleaning as dehydrating and binding materials, as well as screening of coke and coal as a reducing agents. The proposed technology also solves the problems of environmental pollution and land acquisition for the storage of production waste.

Iron powders having average particle sizes of ~40µm are mechanically mixed thoroughly with aluminum powders ranging from 1 to 10 in wt.% with an average particle size of ~10µm. Two different powder metallurgical techniques cold and hot pressing are used to study the effect of the additive element powder on the mechanical properties, wear properties and the microstructure of the iron based alloys. The hot pressing technique was performed at a temperature up to 500°C at 445.6 MPa. The cold pressing technique was performed at 909 MPa in room temperature. By increasing the Al content to 10 wt. % in the base Fe-based matrix, the hardness was decreased from 780 to 690 MPa and the radial strength was decreased from 380 to 202 MPa with reductions of 11.5% and 40%, respectively. Improvement of the wear resistance with the increase addition of the Al powder to the Fe matrix up to 5 times was achieved compared to the alloy without Al addition for different wear parameters namely; wear time and sliding speed.

Byers Peninsula is considered one of the largest ice-free areas in Maritime Antarctica. Since 2006, the Spanish Polar Program has taken part in a large number of environmental studies involving effects of climate changes in lives cycles, limnology and microbiology. Soils from maritime Antarctica are generally weakly developed and have chemical, physical and morphological characteristics strongly influenced by the parent material. However, biological activity during the short Antarctic summer promotes intense transference of nutrients and organic matter in areas occupied by different species of birds and marine mammals. To mapping and monitoring those areas with high biological occupation, could be very useful to have models of edaphic properties prepared from satellite images. In this approach, Deep Learning and Linear Regression models of soil properties and spectral indexes as explicative variables were performed. We training models of soil properties closely related to biological activity such as Dissolved Organic Carbon (DOC) and the iron fraction associated with organic matter (Fe). We tested the best approach to model the spatial distribution of DOC, Fe and pH by training models of Linear Regression and Deep Learning over Sentinel2 and WorldView2 images. The most robust models were used to track possible areas with ornithogenic soils as well as areas of the Byers Peninsula that could support the highest biological development.

The cubic nonlinearity of graphene oxide (GO) monolayer was characterized by open and closed Z-scan using a nano-second laser of 10 Hz repetition rate with a Gaussian spatial beam profile. The reverse saturable absorption or positive nonlinearity from open Z-scan and valley-peak traces or positive nonlinearity from closed Z-scan was displayed. The reverse saturable absorption could be from a two-photon or two-step excitation process due to the larger absorption in the lower visible and upper UV wavelength region compared with the excitation source. The nonlinear absorption and nonlinear refraction coefficient were estimated to be ~ 2.62x10-8 m/W and 3.9x10-15 m2/W, respectively. This study also reveals the effect of nonlinear absorption on nonlinear refraction traces.

The nucleation of voids in alpha iron and the influence of carbon were investigated through a combination of rate theory and nucleation theory calculations. The steady rates of void nucleation exhibit high sensitivity to carbon. Even a seemingly negligible carbon concentration, as low as a few atomic parts per million (appm), can dramatically reduce the nucleation rates and narrow the temperature window for nucleation. This study highlights the challenges in certifying and qualifying nuclear materials for use in reactor environments. It emphasizes the necessity for precise control of impurity levels during materials processing and stringent requirements for irradiation testing, which are susceptible to contamination. Furthermore, the study provides an explanation for the significant data scattering observed in void swelling behaviors as reported in the literature.

Iron deficiency in the fetal and neonatal period (perinatal iron deficiency) bodes poorly to neuro-development. Given its common occurrence and the negative impact on brain development, a screening and treatment strategy that is focused on optimizing brain development in perinatal iron deficiency is necessary. Pediatric societies currently recommend a universal iron supple-mentation strategy for full-term and preterm infants that does not consider individual variation in the body iron status and could lead to under-treatment or over-treatment. Moreover, the focus is on hematological normalcy and not optimal brain development. Several serum iron indices and hematological parameters in the perinatal period are associated with risk of abnormal neurodevelopment, suggesting their potential use as biomarkers for screening and monitoring treatment in infants at risk for perinatal iron deficiency. A biomarker-based screening and treatment strategy that is focused on optimizing brain development will likely improve outcome in perinatal iron deficiency.

Additive Manufacturing and nanotechnology have been used as basic tools for the manufacture of nanostructured parts with magnetic properties to expand the variety of applications in additive processes by tank photopolymerization. Magnetic cobalt ferrite (CoFe2O4) and barium ferrite (BaFe12O19) nanoparticles with the size distribution of average value DTEM of 12 ± 2.95 nm and 37 ± 12.78 nm, respectively were generat-ed by hydroxide precipitation method. The dispersion of the nanoparticles on commercial resins (Anycubic Green and IRIX White resin) was obtained by mechanochemical reactions carried out in an agate mortar for 20 minutes, at room temperature and with limited exposure to light. The product of each reaction was placed in amber vials, also being kept in a box, to avoid contact with light. The photopolymerization process was carried out only at low concentrations (w/w % nanoparticles/resin) since, at high concentrations, there is no for-mation of pieces due to the high refractive index of ferrites. Raman shift spectroscopy of the final pieces showed that they contain the magnetic nanoparticles, with no apparent chemical changes. The EPR results of the pieces maintain the magnetic properties and apparently, they are not modified during the photopolymer-ization. Although significant differences were found in the dispersion process of the nanoparticles in each piece, we determined that the photopolymerization did not influence the structure and superparamagnetic behavior of ferrite nanoparticles during processing, and the magnetic properties were successfully transferred to the final 3D-printed magnetic obtained piece.

Background: Iron chelation medications (desferoxamine, desferasirox, desferiprone) are used to manage iron overload. These medications are partially excreted via the kidneys, desferoxamine and desferiprone excretes primarily in the urine, and desferasirox had about 8% excreted in the urine. Their use in severe kidney disease and dialysis patients is caution as “avoided” concerning adverse effects; however, there are reports safe use. This manuscript reviews the literature in this population. Data Sources: Pubmed: desferasirox, deferiprone, deferoxamine, kidney disease, ESKD, Dialysis. Case reports and case series that described experiences with using iron chelation medications in ESKD patients are included. Data also gathered from reading-related sources. Results: This is a review of desferoxamine, desferasirox, and deferiprone use in kidney disease from 1976 to the present time. Table 1 provides a summary of findings. These are mostly reports and brief descriptions of the experiences used in severe kidney disease and dialysis, but lack of randomized control trials and small number of participants. Conclusions: Iron chelation medications are important for treating iron overload but concerns with adverse effects. Due to limited medications available to treat iron overload in patients with severe kidney disease, their safe use has been reporting in the literature. This is an area that warrants further research.

Introduction: In the recent years alternate day dosing has been recommended in iron deficieny treatment. The aim of this study is to compare the efficacy and side effects of oral iron treatments given daily 1x1, alternate day 1x1 and 2x1 alternate day dosing in iron deficieny anemia patients. Methods: A total of 52 patients with a diagnosis of iron deficiency anemia with serum ferritin level of 25 µg/L or less were included in this retrospective study. Statistical analyzes were done with SPSS V.25. Results: The patients included in our study were between the ages of 18-51. All of the patients included in the study were female. A statistically significant increase was found between 0-14 days(p<0.001), 14-28 days(p<0.001) and 0-28 days(p<0.001) hemoglobin values in all patients. There was no statistically significant difference between 0-14 days (p=0.397) and 0-28 days(p=0.310) ferritin values in all patients. A statistically significant difference was found between 14-28 days(p<0.001) ferritin values. When the rate of change of hemoglobin and ferritin values between the groups was compared and no statistically significant difference was observed between the groups. The rate of change of ferritin values for 14-28 days was significant (p=0.012). There was no significant difference in the frequency of symptoms in the 14th day and 28th day controls for each group (p>0.05). The incidence of metallic taste and bloating symptoms was found to be statistically significant in the third control in the group with 2x1 drug use alternate day (p=0.094). Discussion: The only difference in efficacy was observed in ferritin values between 14th and 28th days. The increase in ferritin values was higher in the group that used 1x1 oral iron every day. However, since no difference was observed between the groups in terms of ferritin and hemoglobin values on days 0 and 28, all three groups were considered equally efficient. Side effects were mainly gastrointestinal side effects. Since the group that received 2x1 oral treatment alternate day had a statistically significantly higher rate of side effects, the patients’ treatment tolerance will be lower compared to the other groups. In conlusion, there is no difference in efficacy and side effects between the patient groups receiving 1x1 daily and 1x1 alternate day oral iron therapy, so 1x1 use alternate day is the most appropriate treatment method for oral iron therapy in terms of patient tolerance, adherence to treatment and pharmacoeconomics.

Legumes are important sources of nitrogen and, therefore, the nitrogen fixing ability of the legume-rhizobia symbiosis has great potential to improve crop yields or reduce nitrogen fertilizer use. Unfortunately, legumes face serious and increasing threats of both biotic and abiotic stresses among which Fe-deficiency has been increased from past years. Fe nutrient deficiency limits pulse production and nitrogen fixation by specifically affecting any one of the four phases of legume-rhizobium symbiosis. Although Fe in soil is often present in adequate quantities, it is mainly present in insoluble Fe-(III) precipitates, limiting its uptake and utilization. The present review has focused on the iron nutrition and deficiency and probable uptake, transport and metabolism in legumes.

Keywords: iron deficiency anemia; IDA; anemia; knowledge; awareness.

Neuronal lesions in Parkinson’s disease (PD) are commonly associated with α-synuclein (α-Syn)-induced cell damage that are present both in the central and peripheral nervous systems of patients, with the enteric nervous system also being especially vulnerable. Here we bring together evidence that the development and presence of PD depends on specific sets of interlinking factors that include neuro-inflammation, systemic inflammation, α-Syn-induced cell damage, vascular dysfunction, iron dysregulation, gut and periodontal dysbiosis. We argue that there is significant evidence that bacterial inflammagens fuel this systemic inflammation, and might be central to the development of PD. We also discuss the processes whereby lipopolysaccharides may be involved in causing nucleation of proteins, including of α-Syn. Lastly, we review evidence that pre-and probiotics, as well as antibiotics and faecal transplant treatment might be valuable treatments in PD. A most important consideration, however, is that these therapeutic options need to be validated and tested in randomized controlled clinical trials. However, targeting underlying mechanisms of PD, including gut dysbiosis and iron toxicity, have potentially opened up possibilities of a wide variety of novel treatments which may relieve the characteristic non-motor deficits of PD, and may even slow the progression and/or accompanying gut-related conditions of the disease.

Mineral extraction is one of the most important for the economies of different countries, and Brazil is one of the world's primary iron ore producers. Unfortunately, the dams are still the main problem, mainly in Minas Gerais, especially after the Fundão Dam rupture happened in 2015. Additionally, there is still a massive presence of buildings produced on earth throughout the Minas Gerais mining region, built from the 18th century to today. Investigating the potential of IOT to be incorporated into traditional earthen construction techniques in regions affected by dam ruptures presents a relevant and innovative research approach. In addition, the local reuse of these sediments should be the priority. Thus, the main objective of this work was to collect, characterize, and analyze the possibilities of application of these tailings to produce RE. XRD, XRF, granulometry, porosity, specific density, toxicity, and MEV/EDS were performed on the samples collected at three points. To analyze the soil-IOT compatibility, representative mixtures of RE were produced, and the specific mass, compaction, and compressive strength were performed. It was observed that the IoT samples have a high silica content and that the mixtures of IOT-soil, even without cement, reached compressive strength values above the current international standards.

Our investigations show that electrochemical corrosion of copper is faster than electrochemical corrosion of aluminium at temperatures below 100oC. Literature data analysis shows that the Al atoms diffuse faster than the Cu atoms at temperatures higher than 475oC, Al rich intermetallic compounds (IMCs) are formed faster in the Cu-Al system, and the Kirkendall plane shifts toward Al side. Electrochemical corrosion occurs due to electric current and due to diffusion. An electronic devise working time, for example, depends on initial copper cover thickness on aluminium wire, connected to the electronic devise, temperature, and volume and dislocation pipe diffusion coefficients, so copper, iron, and aluminium electrochemical corrosion rates are investigated experimentally at room temperature and at temperature 100oC. Intrinsic diffusivities ratios of copper and aluminium at different temperatures and diffusion activation energies in the Cu-Al system are calculated by proposed here methods using literature experimental data. Dislocation pipe and volume diffusion activation energies of pure iron are calculated separately by earlier proposed method using literature experimental data. Aluminium dissolved into NaCl solution as the Al3+ ions at room temperature and at temperature 100oC, iron dissolved into NaCl solution as the Fe2+ (not Fe3+) ions at room temperature and at temperature 100oC, copper dissolved into NaCl solution as the Cu+ ions at room temperature and as the Cu+ and the Cu2+ ions at temperature 100oC. It is founded experimentally that copper corrosion is higher than aluminium corrosion, and ratio of electrochemical corrosion rates, kCu/kAl>1, decreases with temperature increasing, although iron electrochemical corrosion rate doesn’t depend on temperature below 100oC. It is obvious, because melting point of iron is more higher then melting point of copper or aluminium. It is calculated that copper electrochemical corrosion rate is approximately equal to aluminium electrochemical corrosion at temperature about 300oC, so copper can dissolve into NaCl solution mostly as the Cu2+ ions at temperature about 300oC. Ratio of intrinsic diffusivities, DCu/DAl <1, increases with temperature increasing, and intrinsic diffusivity of aluminium could be approximately equal to intrinsic diffusivity of copper at temperature about 460oC.

Enhanced supercontinuum generation (SCG) is experimentally demonstrated in integrated silicon nitride (Si₃N₄) waveguides incorporating highly nonlinear graphene oxide (GO) in the form of two-dimensional (2D) films. On-chip integration of the 2D GO films with precise control of their thickness is realized by using a transfer-free and layer-by-layer coating method. The control of the film length and coating position is achieved via window opening in the upper silica cladding of the photonic integrated chips. Detailed SCG measurements are performed using the fabricated devices with different waveguide geometries and GO film thicknesses, and the results are compared with devices without GO. Significantly improved spectral broadening of ultrashort optical pulses with ultrahigh peaks powers exceeding 1000 W is observed for the hybrid devices, achieving up to 2.4 times improvement in the spectral bandwidth relative to devices without GO. Theoretical analyses for the influence of GO film thickness, coating length, coating position, and waveguide geometry are also provided by fitting the experimental results with theory, showing that there is still significant room for further improvement. This work opens up a promising new avenue towards improving the SCG performance of photonic integrated devices by incorporating functional 2D materials.

Nanostructured carriers have been widely used in pharmaceutical formulations for dermatological treatment. They offer targeted drug delivery, sustained release, improved biostability, and low toxicity, usually presenting advantages over conventional formulations. Due to its large surface area, small size and photothermal properties, graphene oxide (GO) has the potential to be used for such applications. Nanographene oxide (GOn) presented average sizes of 197.6 ± 11.8 nm, and a surface charge of -39.4 ± 1.8 mV, being stable in water for over 6 months. 55.5 % of the mass of GOn dispersion (at a concentration of 1 mg mL-1) permeated the skin after 6 h of exposure. GOn dispersions have been shown to absorb near-infrared radiation, reaching temperatures up to 45.7 °C, within mild photothermal therapy temperature range. Furthermore, GOn in amounts superior to those which could permeate the skin were shown not to affect human skin fibroblasts (HFF-1) morphology or viability, after 24 h of incubation. Due to its large size, no skin permeation was observed for graphite particles in aqueous dispersions stabilized with Pluronic P-123 (Gt-P-123). Altogether, for the first time, GOn potential as a topic administration agent and for delivery of photothermal therapy has been demonstrated.

Water deficit caused by drought is a significant threat to crop growth and production. Nitric oxide (NO), a water- and lipid-soluble free radical, plays an important role in cytoprotection. Apart from a few studies supporting the role of NO in drought responses, little is known about this pivotal molecular amendment in the regulation of abiotic stress signaling. In this review, we highlight the knowledge gaps in NO roles under drought stress and the technical challenges underlying NO detection and measurements, and we provide recommendations regarding potential avenues for future investigation. The modulation of NO production to alleviate abiotic stress disturbances in higher plants highlights the potential of genetic manipulation to influence NO metabolism as a tool with which plant fitness can be improved under adverse growth conditions.

Iron is an essential nutrient for humans and microbes, such as bacteria. Iron deficiency occurs commonly in critically ill patients, but iron replacement therapy is not considered during the acute phase of critical illness, since it increases iron availability for invading microbes and oxidative stress. However, persistent iron deficiency in the recovery phase is harmful with potential adverse outcomes such as cognitive dysfunction, fatigue and cardiopulmonary dysfunction. Therefore, it is important to treat iron deficiency timely and efficiently. This article reviews current knowledge about iron-related biomarkers in critically ill patients and provides possible criteria to guide decision-making for iron supplementation in the recovery phase of critical illness.

Many drastic actions are taken by cocaine users for the sake of experiencing high dopamine levels, which depends on iron for its synthesis. Dopamine depletion and iron deficiency are also involved in the symptoms of restless leg syndrome (RLS). The intersecting biochemical pathways of cocaine use, iron deficiency, and RLS have not been adequately investigated. This case report reveals the successful treatment of a patient with these conditions. A 63-year-old male with a history of cocaine use disorder, insomnia, and RLS sought emergency care for suicidality. Upon admission, he was also found to be iron-deficient. He revealed that his RLS worsened when he attempted to abstain from cocaine. He also used alcohol to sustain the effects of cocaine when the cost of cocaine was too high. During hospitalization, his mood, cravings, and RLS were resolved with adjunctive iron supplementation as well as 300 mg of Wellbutrin. If iron-deficient, replenishment of adequate dopaminergic receptor density and function via supplementation may play an essential role in the prevention of cocaine use and cessation of cocaine withdrawal. Further research is warranted to validate these findings and understand the implications of iron supplementation in addiction medicine.

Organometallic drug development is still in its early stage, but recent studies show that organometallics having iron as the central atom have the possibility of becoming good drug candidates because iron is an important micro-nutrient, and it is compatible with many biological systems, including the human body. Being an eco-friendly Lewis acid, iron can accept the lone pair of electrons from imino(sp2)-nitrogen, and the resultant iron-imine complexes with iron as a central atom have the possibility of interacting with several proteins and enzymes in humans. Iron-imine complexes have demonstrated significant potential as anticancer, bactericidal, fungicidal, and other medicinal activities in recent years. This article systematically discusses major synthetic methods and pharmacological potentials of iron-imine complexes having in vitro activity to significantly affect clinical performance from 2016 to date. In a nutshell, this manuscript offers a simplistic view of iron complexes in medicinal inorganic chemistry: for instance, iron is presented as an "eco-friendly non-toxic" metal (as opposed to platinum) that will lead to non-toxic pharmaceuticals. The abundant literature on iron chelators shows that many iron complexes, particularly if redox-active in cells, can be quite cytotoxic, which can be beneficial for future targeted therapies. While we made every effort to include all the related papers, any omission is purely unintentional.

Nuclear receptor coactivator 4 (NCOA4) is a selective cargo receptor that mediates the autophagic degradation of ferritin (“ferritinophagy”), the cytosolic iron storage complex. NCOA4-mediated ferritinophagy maintains intracellular iron homeostasis by facilitating ferritin iron storage or release according to demand. Ferritinophagy is involved in iron-dependent physiological processes such as erythropoiesis, where NCOA4 mediates ferritin iron release for mitochondrial heme synthesis. Recently, ferritinophagy has been shown to regulate ferroptosis, a newly described form of iron-dependent cell death mediated by excess lipid peroxidation. Dysregulation of iron metabolism and ferroptosis have been described in neurodegeneration, cancer, and infection, but little is known about the role of ferritinophagy in the pathogenesis of these diseases. Here, we will review the biochemical regulation of NCOA4, its contribution to physiological processes and its role in disease. Finally, we will discuss the potential of activating or inhibiting ferritinophagy and ferroptosis for therapeutic purposes.

Green synthesis offers a superior alternative to traditional methods for producing metal and metal oxide nanoparticles. This approach is not only benign and safe but also cost-effective, scalable, and straightforward, operating under ambient conditions. Notable metals and metal oxide nanoparticles, such as manganese oxides, iron oxides, silver, and gold, have been produced using various bio-reductants derived from plant extracts. These biological agents not only expedite the reduction process but also stabilize the nanoparticles, serving dual roles as reducing and capping agents. This review presents the green synthesis of nanoparticles (NPs) obtained from biogenic wastes and plant extracts. The green-synthesized nanostructured MnO2 are evaluated as a potential photocatalyst for water treatment and as an electrode material in lithium-ion batteries and supercapacitors. The green-derived iron oxide nanoparticles are examined as promising antioxidant, anti-inflammatory, and anti-diabetic agents. Additionally, this review discusses the green synthesis of precious metal nanoparticles, specifically silver (Ag NPs) and gold (Au NPs), highlighting their potential medical applications in areas like antiviral treatments and cancer therapy.

The master molecular regulators and mechanisms determining longevity and health span include nitric oxide (NO) and superoxide anion radicals (SOR). L-arginine, the NO synthase (NOS) substrate, can restore a healthy ratio between the dangerous SOR and the protective NO radical to promote healthy aging. Antioxidant supplementation orchestrates protection against oxidative stress and damage—L-arginine and antioxidants such as vitamin C increase NO production and bioavailability. Uncoupling of NO generation with the appearance of SOR can be induced by asymmetric dimethylarginine (ADMA). L-arginine can displace ADMA from the site of NO formation if sufficient amounts of the amino acid are available. Antioxidants such as ascorbic acids can scavenge SOR and increase the bioavailability of NO. The topics of this review are the complex interactions of antioxidant agents with L-arginine, which determine NO bioactivity and protection against age-related degeneration.

The master molecular regulators and mechanisms determining longevity and health span include nitric oxide (NO) and superoxide anion radicals (SOR). L-arginine, the NO synthase (NOS) substrate, can restore a healthy ratio between the dangerous SOR and the protective NO radical to promote healthy aging. Antioxidant supplementation orchestrates protection against oxidative stress and damage—L-arginine and antioxidants such as vitamin C increase NO production and bioavailability. Uncoupling of NO generation with the appearance of SOR can be induced by asymmetric dimethylarginine (ADMA). L-arginine can displace ADMA from the site of NO formation if sufficient amounts of the amino acid are available. Antioxidants such as ascorbic acids can scavenge SOR and increase the bioavailability of NO. The topics of this review are the complex interactions of antioxidant agents with L-arginine, which determine NO bioactivity and protection against age-related degeneration.

A chronically stable electrode material with low impedance for recording neural activity and high charge-injection capacity for functional electro-stimulation is desirable for the fabrication of implantable microelectrode arrays that aims to restore impaired or lost neurological functions in humans. For this purpose, we have investigated the electrochemical properties of sputtered ruthenium oxide (RuOx) electrode coatings, deposited on planar microelectrode arrays, using an inorganic model of interstitial fluid (model-ISF) at 37o C as the electrolyte. Through a combination of cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS) modelling study we have established the contribution of faradaic reaction as the major charge-injection contributor within the safe neural stimulation potential window of 0.6 V vs Ag|AgCl. We have also established the reversibility of the charge-injection process for sputtered RuOx film by applying constant charge-per-phase current stimulations at different pulse widths and by comparing the magnitudes of leading and trailing access voltages during voltage transient measurements. Finally, the impedance of the sputtered RuOx film was found to be reasonably comparable in both its oxidized and reduced states, although electronic contribution from capacitive double-layer was found to be slightly higher for the completely oxidized film around 0.6 V than its reduced counterpart around -0.6V.

Two once-through steam generators and a combination of a steam generator and a gas preheater for supplying feed gases to solid-oxide electrolysis stacks were evaluated for their carryover characteristics of contaminants from the feed-water into the steam phase. The concentrations of various trace impurities in the steam were determined by sampling the steam condensates and screening them with inductively coupled plasma - mass spectrometry for 19 elements and liquid ion chromatography and continuous flow analysis for chloride and ammonium. Steam soluble species like boric acid undergo complete volatilization and transfer into the steam phase. During unstable evaporation in the steam generators an extensive physical carryover of alloying metal species was observed. At realistic operation conditions for steam electrolysis, the gas preheater caused a considerable release of silicon into the steam phase. Two stack experiments were performed with common preheater temperatures and showed largely increased cell voltage degradation at higher operation temperatures. The post-test chemical analysis of cell samples revealed significant concentrations of silicon in the samples that are regarded as primary cause for increased degradation. These findings could partially explain the wide spread of degradation rates reported for solid-oxide steam electrolysis experiments.

Iron plays a critical role in lung infections due to its function in the inflammatory immune response but also as an important factor for bacterial growth. Iron chelation represents a potential therapeutic approach to inhibit bacterial growth and pathologically increased pro-inflammatory mediator production. The present study was designed to investigate the impact of the iron chelator, DIBI, in murine lung infection induced by intratracheal Pseudomonas aeruginosa (strain PA14) administration. DIBI (80mg/kg) was given by intraperitoneal injection either as a single dose immediately after PA14 administration or a double dose (second dose 4 h after PA14 administration). The results showed that lung NF-κBp65 levels, as well as levels of various inflammatory cytokines (TNFα, IL-1β, IL-6) both in lung tissue and bronchoalveolar lavage fluid (BALF), were significantly increased 24h after PA14 administration. Single-dose DIBI did not affect the bacterial load or inflammatory response in the lungs or BALF. However, two doses of DIBI significantly decreased bacterial load, attenuated NF-κBp65 upregulation, reduced inflammatory cytokines production, and relieved lung tissue damage. Our findings support the conclusion that the iron chelator, DIBI, can reduce lung injury induced by P. aeruginosa, via its anti-bacterial and anti-inflammatory effects.

The substrate N1, N3, N5 -tris(2-hydroxyphenyl)benzene-1,3,5-tricarboxamide (Sensor A) was prepared in the reaction of 1,3,5-benzenetricarboxylic acid (trimesic acid) and o-aminophenol in ethanol. The prepared organic sensor fulfills the chemiluminescent requirements including luminophore, spacer, and suitable binding receptor that distress the probe's luminescent features, providing selective and sensitive detection of mercury and iron ions in aqueous solutions. The sensor selectively detects mercury and iron ions in a water matrix containing various metal ions including sodium, calcium, magnesium, zinc, and nickel. Strong and immediate binding was observed between mercury ions and the substrate at pH 7.0 with a binding affinity toward Hg (II) enhanced by nine folds higher than that observed for iron sensor binding affinity, which makes the substrate a distinctive luminescence sensor for mercury detection at ambient conditions. The sensor shows a linear response toward Hg (II) in the concentration range from 4.2 x 10-5 to 2.0 x 10-8 M with a limit of detection of 1.0 x 10-8 M. Further, Sensor A provides linear detection for iron ions in the range from 1.5 x 10-3 to 1.5 x 10-8 M. The measured adsorption capacity of Sensor A toward mercury ions ranged from 1.25 to 1.97 mg/g and the removal efficiency from water samples reached 98.8% at pH 7.0. The data demonstrate that Sensor A is an excellent probe for detecting and removing mercury ions from water bodies.

The world is facing a serious energy crisis and environmental pollution problems due to a sharp increase in the world population. Bioenergy is an eminent solution to these problems. Anaerobic digestion is a green energy technology used worldwide for the conversion of organic waste to biogas. It is reported that organic wastes are hard to digest and need some technical improvement in the anaerobic digestion process to improve biogas yield. Iron-based additives, due to their electron acceptance and donation capabilities, have been emphasized as being exceptional in improving anaerobic digestion process efficiency amongst all other enhancement options. This study reviews the major available types of iron-based additives, their characteristics, and their preparation methods. The preferred iron-based additive that has a significant effect on the enhancement of biogas yield is also discussed. The use of iron-based additives in the anaerobic digestion process with varying dosages and their impact on the biogas generation rate is also being studied. Substrates, operating parameters, and types of anaerobic digesters used in recent studies while researching the effects of iron-based additives are also part of this review. Lastly, this study also confirms that iron-based additives have a significant effect on the reduction rate of the volatile suspended solids, methane content, biogas yield, and volatile fatty acids.

Streptococcus suis is a zoonotic pathogen causing serious infections in both swine and humans. Although metals are essential for life, excess amounts of metals they are toxic to bacteria. when accumulated in excess amounts. Except for zinc, Transcriptome-level data of the mechanisms for resistance to metal-induced toxicity in S. suis are available for no metals other than zinc. have not been investigated from the transcriptome level in S. suis. Herein, we explored the transcriptome-level changes of in S. suis in response to ferrous iron and cobalt toxicity by RNA sequencing. Many A lot of genes were differentially expressed in the presence of excess ferrous iron and cobalt. Most of the genes in response to cobalt toxicity showed the same expression trends as those were expressed in the same trend in response to ferrous iron toxicity. qRT-PCR analysis of the selected genes confirmed the accuracy of RNA sequencing results. Bioinformatics analysis of the differentially expressed genes indicated that ferrous iron and cobalt have similar impacts effects on the cellular processes of S. suis. Treatment with ferrous Ferrous iron treatment resulted in down-regulation of several oxidative stress tolerance-related genes involved in oxidative stress tolerance and up-regulation of the genes in an amino acid ABC transporter operon. Expression of the several genes in the arginine deiminase system was down-regulated in the presence of after ferrous iron and cobalt treatment. Collectively, our results suggested that S. suis alters the expression of a lot of multiple genes to respond to ferrous iron and cobalt toxicity.

Lifespan extension was recently achieved in Caenorhabditis elegans nematodes by mitochondrial stress and mitophagy, triggered via iron depletion. Conversely in man, deficient mitophagy due to Pink1/Parkin mutations triggers iron accumulation in patient brain and limits survival. We now aimed to identify murine fibroblast factors, which adapt their mRNA expression to acute iron manipulation, relate to mitochondrial dysfunction and may influence survival. After iron depletion, expression of the plasma membrane receptor Tfrc with its activator Ireb2, the mitochondrial membrane transporter Abcb10, the heme-release factor Pgrmc1, the heme-degradation enzyme Hmox1, the heme-binding cholesterol metabolizer Cyp46a1, as well as the mitophagy regulators Pink1 and Parkin showed a negative correlation to iron levels. After iron overload, these factors did not change expression. Conversely, a positive correlation of mRNA levels with both conditions of iron availability was observed for the endosomal factors Slc11a2 and Steap2, as well as for the iron-sulfur-cluster (ISC)-containing factors Ppat, Bdh2 and Nthl1. Positive correlation only after iron depletion was observed for the iron export factor Slc40a1, mitochondrial iron transporters Slc25a28, Abcb7 and Abcb8, mitochondrial ISC-containing factors Glrx5, Nfu1, Bola1 and Abce1, cytosolic Aco1 and Tyw5, as well as nuclear Dna2, Elp3, Pold1 and Prim2. The latter are regulators of nucleotide synthesis and DNA quality control, which have known importance for growth and lifespan. The only Pink1-/- triggered transcript modulation was the reduced expression of the ISC-containing ribosomal factor Abce1. These mammalian findings support previous fly data that Pink1 influences co-translational quality control via Abce1, as well as mitophagy. Our findings provide the first systematic survey how iron dosage triggers homeostatic transcriptional regulations and elucidate how iron deprivation results in mitophagy.

Background: The role of inhaled Nitric Oxide (iNO) in managing Acute Respiratory Distress Syndrome Covid-19 related (C-ARDS) is debatable. The study aimed to analyze the effect of iNO administration in patients with persistent severe hypoxia and Intensive Care Unit (ICU) mortality. Methods: This retrospective study included 98 consecutive critically ill patients with C-ARDS admitted to ICU from 1 October 2020 to 31 October 2021. Results: Of these patients, 28% had received iNO. Twelve (44.4%) were responders. Kaplan-Mayer plot shows mortality was higher in non-responders (86.6 vs 25.0%). Non-response to iNo was the most important predictive value (p. 0.01). The Receiver Operating Characteristic (ROC) curve for a percentage increase in PaO2 from baseline confirmed that it had a higher predictive value for in-hospital survival. A value of 19% can predict the death event with a sensitivity of 81.8% and a specificity of 81.2%. Conclusions: Therefore, we propose to use iNO as a vasoreactivity test for prognostic stratification in patients with persistent severe hypoxia.

Iron oxide nanoparticles have been investigated due to their suitable characteristics for diverse applications in the fields of biomedicine, electronics, water/wastewater treatment and sensors. Maghemite, magnetite and hematite are the most widely studied iron oxide particles and have ferrimagnetic characteristics. When very small, however, these particles have superparamagnetic properties and are called superparamagnetic iron oxide nanoparticles (SPIONs). Several methods are used for the production of these particles, such as coprecipitation, thermal decomposition and microemulsion. However, the variables of the different types of synthesis must be assessed to achieve greater control over the particles produced. In some studies, it is possible to compare the influence of variations in the factors for production with each of these methods. Thus, researchers use different adaptations of synthesis based on each objective and type of application. With coprecipitation, it is possible to obtain smaller, more uniform particles with adjustments in temperature, pH and the types of reagents used in the process. With thermal decomposition, greater control is needed over time, temperature as well as the proportion of surfactants and organic and aqueous phases in order to produce smaller particles and a narrower size distribution. With the microemulsion process, the control of the confinement of the micelles formed during synthesis through the proportions of surfactant and oil makes the final particles smaller and less dispersed. These nanoparticles can be used as additives for the creation of new materials, such as magnetic bacterial cellulose, which has different innovative applications. Composites that have SPIONs, which are produced with greater rigour with regards to size and distribution, have superparamagnetic properties and can be used in medical applications, whereas materials containing larger particles have ferromagnetic applications. To arrive at a particular particle with specific characteristics, researchers must be attentive to both the mechanism selected and the production variables to ensure greater quality and control of the materials produced.

Many stable water dispersions of various chemical compositions containing bioactive chemical compounds: copper silicate, titanium dioxide and zinc oxide (and other auxiliary substances) were developed and fabricated - they were used for preparation of thin hybrid coatings having very good antimicrobial properties against gram negative bacteria (Escherichia coli), gram positive bacteria (Staphylococcus aureus) and yeast fungus (Candida albicans). Polyester (PES) nonwovens were modified by dip-coating, and PES and cotton fabrics - by dip-coating and coating methods.

Detailed evaluation is provided for the likelihood statistics intrinsic to interlocking Sequential Bayes analysis, which allows estimation of evidential support for dendrograms charting the macroevolution of taxa. It involves complexity functions, such as fractal evolution, to generate well-supported evolutionary trees. Required are data on trait changes from ancestral species to descendant species, which is facilitated by reduction of large genera to monothetic groups (one ancestral species each), most conveniently named as separate genera. Assigning each species one Shannon informational bit per new trait, then adding the traits as sequential Bayesian analysis (each posterior probability used as the prior for the next iteration of Bayes Formula), then interpretation with an odds chart, provides a posterior probability that the ancestor-descendant order is correct, that is, entirely follows evolutionary theory involving adaptation and rarity of total trait reversals. The key fact is that the most recently acquired traits of the ancestral species are selectively inviolate and passed on without change to each descendant species. The details of sequential Bayesian analysis were clarified by calculation of likelihood ratios and Bayes factors that compare optimal models with the next most likely model. Such analysis demonstrated that the optimum arrangement of ancestor and descendant species leads to high support values for fitting evolutionary theory, comparable to statistical support levels reported for molecular evolutionary trees. The fact that phylogenetic analysis does not offer an ancestor-descendant model in is found to be conducive of precision at the expense of accuracy, and leads to wrong ancestor-free models with likelihoods explaining data at high credible levels. The number of advanced traits in the outgroup as a Bayesian prior greatly enhances posterior probability. The method is simple, free of special computer analysis, and well-suited to standard taxonomic practice.

The 11 system in iron-based superconducting family has become one of the most extensively studied materials in the research of high-temperature superconductivity due to their simple structure and rich physical properties. However, the research on 11 iron-based superconductors faces numerous obstacles, mainly stemming from the challenges associated with producing high-quality single crystals. Since the discovery of FeSe superconductivity in 2008, researchers have made significant progress in crystal growth, overcoming the hurdles that initially impeded their studies. Consequently, they have successfully established the complete phase diagrams of 11 iron-based superconductors, including FeSe1-xTex, FeSe1-xSx and FeTe1-xSx. In this paper, we aim to provide a comprehensive summary of the preparation methods employed for 11 iron-based single crystals over the past decade. Specifically, we will focus on hydrothermal, chemical vapor transport (CVT), self-flux, and annealing methods. Additionally, we will discuss the quality, size, and superconductivity properties exhibited by single crystals obtained through different preparation methods. By exploring these aspects, we can gain a better understanding of the advantages and limitations associated with each technique.

Food processing and consumption involves multiple contacts between biological fluids and solid materials of processing devices of which steel is one of the most common. Due to complexity of these interactions, it is difficult to identify the main control factors in the formation of undesirable deposits on the device surfaces that may affect safety and efficiency of the processes. Mechanistic understanding of biomolecule-metal interactions involving food proteins could improve management of these pertinent industrial processes and consumer safety in food industry and beyond. In this work, we perform a multiscale study of formation of protein corona on iron surfaces and nanoparticles in contact with cow milk proteins. By calculating the binding energies of proteins with the substrate we quantify the adsorption strength and rank proteins by the adsorption affinity. We use a multiscale method involving all-atom and coarse-grained simulations as well as generation of 3D structures of the proteins for this purpose. Finally, using the adsorption energy results, we predict the composition of protein corona on iron nanoparticles and flat surfaces via a competitive adsorption model.

Chronic diseases are characterised by cell’s autophagy and proteins disarrangement resulting in sarcopenia, hypoalbuminemia and hypo-haemoglobinaemia. Hypo-haemoglobinaemia couses worse prognosis independentely of the principal disease. Currently, the cornerstone of therapy of anaemia is iron supplementation, with or without erythropoietin for the stimulation of hematopoiesis. However, treatment strategies should incorporate the addition of heme, the principal biochemical constituent of haemoglobin. Heme synthesis follows a complex biochemical pathway. The limiting step of heme synthesis is D-ALA availability which, for its synthesis, requires Glycine and Succinil-CoA. Consequently, treatment of anaemia should not be based only on iron availability, but also on the availability of the molecules fundamental for heme synthesis. Therefore, an adequate clinical therapeutic strategy should integrate the standard iron infusion and the supply of essential amino acids and vitamins involved in the heme synthesis. We report preliminary data in selected elderly anaemic patients with congestive heart failure (CHF) and catabolic disarrangement, who, in addition to standard iron therapy, received personalized therapy with essential-AAs and vitamins involved in the maintenance of heme. Notably, such individualized therapy resulted in a significant increase in the serum concentration of haemoglobin after 30 days of treatment compared to standard iron therapy.