Silicon carbide single crystal (SiC) has been widely used in the field of power devices, while it is difficult to fabricate ultra-flat surface by traditional manufacturing technologies due to its difficult-to-machine property. This paper investigates the interaction process during femtosecond laser ablation of crystalline silicon carbide based on the two-temperature model simulation and experimental study. The findings reveal that parameters such as laser pulse energy, scanning interval, and defocus amount exert significant influence on ablation depth, roughness, and surface morphology. The femtosecond laser proves effective in removing surface defects from cut SiC substrates, albeit resulting in increased surface roughness. However, subsequent polishing treatment of the laser-ablated silicon carbide surface can mitigate this roughness, underscoring the feasibility of laser surface ablation for silicon carbide single crystals.

In this paper, the deformation behavior of S32750 duplex stainless steel during low cycle fatigue was studied by controlling number of cycles. The microstructure of the specimens under different cycles was characterized by optical microscope (OM), scanning electron microscope (SEM), electron backscatter diffraction (EBSD) and transmission electron microscope (TEM). Microhardness of two phases was measured by a digital microhardness instrument. The results showed that the microhardness of ferrite increases significantly after the first 4000 cycles, while the austenite shows a higher strain hardening rate after fatigue fracture, and the microhardness of ferrite and austenite increases by 23 HV and 87 HV, respectively. Two-phase kernel average misorientation (KAM) diagram showed that the continuous accumulation of plastic deformation easily leads to the initiation of cracks inside the austenite and at the phase boundaries. The evolution of dislocation morphology in two phases was obviously different. With the increase of cycle number, the dislocation in ferrite gradually transforms from dislocation bundles and dislocation array to sub-grain structure, while the dislocation in austenite gradually develops from dipole array to ordered Taylor lattice network structure.

As a new type of high-performance material, gradient structural steel is widely used in engineering fields due to its unique microstructure and excellent mechanical properties. For the prevalent fatigue failure problem, the rate of change of the local grain size gradients along the structure (referred to as the gradient rate) is a key parameter in the design of gradient structures, which significantly affects the fatigue performance of gradient structural steel. In this work, a method of ‘Voronoi primary + secondary modeling’ is adopted to successfully establish three typical high-strength steel models corresponding to the convex, linear, and concave type gradient rates for gradient structures, focusing on the stress-strain response and crack propagation in structural steel with different gradient rates under cyclic loading. It is found that the concave gradient rate structural model is dominated by finer grains with larger volume fraction, which is conducive to hindering fatigue crack propagation and has the longest fatigue life; the linear structure is the second one, and the convex structure is the shortest one. The simulation results in this work are consistent with the relevant experimental phenomena. Therefore, when regulating the gradient rate, priority should be given to increasing the volume fraction of fine grains and designing a gradient rate structure dominated by fine grains to improve the fatigue life of the material.

It is important to realize the transformation behavior of wüstite because it greatly affects the final structure of the oxide layer and the surface quality of the steel products. In the present study, the transformation behaviors of the wüstite layer are examined under nearly-oxygen-free conditions, to simulate the cooling processes after the hot rolled strip is coiled. As the single phase wüstite was prepared at 950˚C, the 460˚C transformed oxide layer was composed of a mixture of iron and magnetite formed through eutectoid reactions. For the 750˚C-fabricated wüstite, only magnetite was observed after transformation, without iron precipitates and residual wüstite. It is speculated that the unusual transformation behavior of the low-temperature-made wüstite results from the pseudo-structural intermediate phase transformation between wüstite and magnetite. This pseudo-structure is a pre-transformed wüstite and of various concentration of ferrous ion, which is determined by the fabrication conditions. During the hot strip mill process, the so-called wet scale, wüstite, is produced continuously from finish mill to laminar flow sections and ended at 570˚C. Consequently, the final eutectoid transformation below 570˚C is dominantly controlled by the surface temperature ranged from 750˚C to 950˚C for low carbon steel.

Iron powders having average particle sizes of ~40µm are mechanically mixed thoroughly with aluminum powders ranging from 1 to 10 in wt.% with an average particle size of ~10µm. Two different powder metallurgical techniques cold and hot pressing are used to study the effect of the additive element powder on the mechanical properties, wear properties and the microstructure of the iron based alloys. The hot pressing technique was performed at a temperature up to 500°C at 445.6 MPa. The cold pressing technique was performed at 909 MPa in room temperature. By increasing the Al content to 10 wt. % in the base Fe-based matrix, the hardness was decreased from 780 to 690 MPa and the radial strength was decreased from 380 to 202 MPa with reductions of 11.5% and 40%, respectively. Improvement of the wear resistance with the increase addition of the Al powder to the Fe matrix up to 5 times was achieved compared to the alloy without Al addition for different wear parameters namely; wear time and sliding speed.

Commercially pure (c.p.) iron powders with a deliberate high degree of oxidation were consolidated by medium-frequency electrical resistance sintering (MF-ERS). This is a consolidation technique where pressure, and heat coming from a low-voltage and high-intensity electrical current, are simultaneously applied to a powder mass. In this work, the achieved densification rate is interpreted according to a qualitative microscopic model, based on the compacts global porosity and electrical resistance evolution. The effect of current intensity and sintering time on compacts was studied on the basis of micrographs revealing the porosity distribution inside the sintered compact. The microstructural characteristics of compacts consolidated by the traditional cold-press and furnace-sinter powder metallurgy route are compared with results of MF-ERS consolidation. The goodness of MF-ERS versus the problems of conventional sintering when working with oxidized powders is analyzed. The electrical consolidation allows to obtain higher densifications than the traditional route under non-reducing atmospheres.

Iron supplementation is associated with side effects and thus reduces the intake compliance. Because it has fewer side effects, a recent trial recommended low-iron micronutrient powder (MNP) for the prevention of anemia in Bangladeshi children exposed to a high concentration of iron from drinking groundwater. In the present study, we hypothesize that the low-iron MNP is a potential intervention to prevent childhood anemia in the low groundwater-iron settings in Bangladesh. A cross-sectional study was conducted in Bangladesh with children aged 2-5 years who drank groundwater containing a low level of iron (0-<2 mg/L).The combined intake of iron was calculated from the key sources--diet, groundwater and MNPs. The intakes of iron were compared against the standard reference intake. The children’s hemoglobin was measured using a photometer. Combined intake of iron from dietary, groundwater and low-iron MNP in children was 5.8±2.0 and 6.9±2.5 mg/day comprising 193% and 169% of the Estimated Average Requirement in the 2-3 year-old and 4-5 year-old subgroups, respectively. Combined intake of bioavailable iron from dietary and groundwater sources was 0.42±0.023 and 0.22±0.019 mg/day in children exposed to groundwater concentration 0.8-<2.0 mg/L and 0.0-<0.8 mg/L respectively (p<0.001). The mean concentration of hemoglobin in the respective groups was 12.17±0.94 mg/dl and 11.91±0.91 mg/dl (p=0.30). The combined intake of iron from dietary and groundwater sources was associated with maintenance of hemoglobin concentration at the non-anemic level in most of the children. The finding highlights the potential of low-iron MNP in controlling childhood anemia in this setting.

AgW materials exhibit excellent properties and are widely used as contact materials in low- and medium-voltage switches. In this study, a pre-sintering and infiltration method was employed to pre-sinter W powder with Cu, Ni, and (Cu+Ni) addition in the low temperature range of 950–1050 °C. The low-temperature sintering behaviours of W skeletons with different additives were investigated. Subsequently, AgW70, AgW75, AgW80, and AgW85 materials were prepared through infiltration at 1050 °C. The microstructure morphology and physical properties of high-W contact materials were investigated using a metallographic microscope and scanning electron microscope. The mechanism of low-temperature sintering-infiltration of high-W contact materials was elucidated. The results indicated that pure W and 1% Cu-added W skeletons experience minimal linear shrinkage within the temperature range of 950–1050 °C. The linear shrinkage curves of W skeletons with different additives coincided under the conditions of 950–1000 °C/90 min. At 1050 °C, after sintering for 150 min, the particle boundaries in the W skeleton were fully spheroidised, with a dihedral angle of 120°. At 1050 °C and after 150 min of infiltration, cross-sectional micrographs of the AgW material revealed the presence of irregular Ni layers, where Ni spatially enveloped/encapsulated Ag. With an increase in the W content, the electrical conductivity and relative density of AgW(70–85) materials decreased, whereas the hardness of the materials increased.

The parallel connection of multiple flexible rings in raceways can significantly improve the electrical conductivity of rolling conductive devices. Multiple flexible rings are generally separated by idlers to form ring-idler rolling pairs. In the present work, alumina (Al2O3), polytetrafluoroethylene (PTFE), polyether ether ketone (PEEK), and polyimide (PI) were used as idler materials. Rolling tests for four types of ring-idler contact pairs were carried out in the air at a rotating speed of 10 rpm and a current of 60 A. It was noticed that the voltage drop was the lowest when Al2O3 was incorporated as the idler material. The energy spectrum analysis indicated material transfer between the organic idlers and the flexible ring. Especially on the flexible ring surface, the transferred organic thin film covered the gold-plated layer of the flexible ring and affected the electrical contact of the flexible ring. The transfer of Al2O3 was not obvious, and the mass fraction of Au on the flexible ring surface after the rolling test was 93.1%. The above results could help in selecting the best idler material for high-power conductive rotary joints.

Iron (Fe) is co-factor for enzymes of the developing brain necessitating sufficient supply. We investigated the effects of administering ferric derisomaltose/Fe isomaltoside (FDI) subcutaneously to Fe deficient (ID) pregnant rats on cerebral and hepatic concentrations of essential metals and gene expression of ferroportin and hepcidin. Pregnant rats subjected to ID were injected with FDI on the day of mating (E0), 14 days into pregnancy (E14), or the day of birth (Postnatal (P0)). The efficacy was evaluated by determination of cerebral and hepatic Fe in pups on P0 and as adults on P70, and the concentration of copper (Cu) and zinc (Zn). Females fed an ID diet (5.2 mg/kg Fe) had offspring with significantly lower cerebral and hepatic Fe compared to female controls fed a standard diet (158 mg/kg Fe). Cerebral Cu increased irrespective of supplying a standard diet or administering FDI combined with the standard diet. Hepatic hepcidin was significantly lower following ID, whereas cerebral hepcidin was virtually undetectable in all experimental groups. In conclusion, administering FDI subcutaneously to ID pregnant rats on EO normalizes cerebral Fe in the fetus, but when applied at later gestational ages, additional Fe to the offspring is needed to normalize cerebral and hepatic Fe.

While L-PBF offers advantages in terms of geometrical freedom or lightweight construction, its use is often limited by economic constraints or currently achievable part costs. With an anticipated increase of L-PBF machine productivity during the next years, an increase of the share of material costs and the share of non-productive time for powder layer application process is to be expected. This results in a demand for less expensive powder materials and advanced processing strategies for the short-and medium-term advancement of L-PBF. As one possible approach, the processing of gas- and water atomized stainless steel (316L) powders with different morphology and particle size distribution as well as their impact on L-PBF productivity is investigated. The actual powder applicability in L-PBF systems and the L-PBF processability determines the minimum necessary powder quality. The main focus of the presented work is put on the interaction between powder quality, powder layer properties, part quality and cost-effectiveness of the L-PBF process. To this end, the influence of the gas and water-atomized powder properties (particle size and morphology) during the powder layer application process at highest possible powder recoater speeds and the resulting powder bed properties (powder layer density, powder bed density, powder demixing) and part properties (part density and tensile strength) is investigated.

The properties of carbon powder filled nitrile rubber (NBR) were investigated. The effect of carbon powder content on the mechanical strength, vulcanization properties, mechanical properties, electrical conductivity, and thermal conductivity of NBR was explored. The purpose of the research is to pursue the optimal filling ratio and conditions of carbon powder to optimize the performance of rubber products.The reasonable filling range of carbon powder has been compared with N660 carbon black filled NBR and determined to evaluate the advantages and disadvantages of carbon powder. The suitable application scenarios of carbon powder is clarified .The research results indicate that carbon powder can delay the sulfurization of NBR in the sulfurization system. The research results indicate that carbon powder can delay the sulfurization of NBR. In terms of filling system, the tensile strength, tear strength, and elongation at break of NBR gradually enhance as the amount of carbon powder increases. Carbon powder can replace carbon black in the application of NBR to improve the comprehensive performance of NBR, which provides a new kind of reinforcing material for NBR.

Effects of oxygen content on microstructure and creep property of FGH96 superalloy were investigated. When oxygen content increased from 135ppm to 341ppm, prior particle boundary (PPB) rose from degree 2 to degree 3, and the size of γ′ phase on PPB enlarged from 1.07μm to 1.27μm, and MC carbide size grew from 77.4nm to 104.0nm. Meanwhile, the steady creep rate accelerated form 4.34×10-3 h-1 to 1.87×10-2 h-1, and the creep rupture life shortened from 176h to 94h, and the creep rupture mode transferred from intergranular and transgranular mixed fracture to along PPB fracture. During creep, the micro-twins formation and gliding will be restrained by ∑3 boundaries. FGH96 superalloy with higher oxygen content contains less ∑3 boundaries and its micro-twins cross slipped instead of single direction slip in lower oxygen content superalloy. Consequently, specimen with higher oxygen content creeped faster and raptured earlier.

Pretreatment of cells with proteolysis inhibitors diminished intensity and changed shape of DNICs specific EPR signal in a treatment time-dependent manner. The level of DNIC formation was significantly influenced by the presence of protein degradation products. Interestingly, formation of HMWDNICs depended on the availability of LMWDNICs. The extent of glutathione involvement in the in vivo formation of DNICs is minor yet noticeable, aligning with our prior research findings.

Iron is an essential nutrient for humans and microbes, such as bacteria. Iron deficiency occurs commonly in critically ill patients, but iron replacement therapy is not considered during the acute phase of critical illness, since it increases iron availability for invading microbes and oxidative stress. However, persistent iron deficiency in the recovery phase is harmful with potential adverse outcomes such as cognitive dysfunction, fatigue and cardiopulmonary dysfunction. Therefore, it is important to treat iron deficiency timely and efficiently. This article reviews current knowledge about iron-related biomarkers in critically ill patients and provides possible criteria to guide decision-making for iron supplementation in the recovery phase of critical illness.

Abstract: Transcription factors are crucial pre-transcriptional regulatory mechanisms that can modulate the expression of downstream genes by binding to their promoter regions. DOF (DNA binding with One Finger) proteins are a unique class of transcription factors with extensive roles in plant growth and development. Our previous research indicated a decrease in iron content in chlorotic bamboo leaves. However, to our knowledge, genes related to iron metabolism pathways in bamboo species have not yet been studied. Therefore, in the current study, we identified iron metabolism-related (IMR) genes in bamboo and determined the transcription factors that significantly influence them. Among these, DOFs were found to have widespread effects and potentially significant impacts on their expression. We identified specific DOF members in Dendrocalamus latiflorus with binding abilities through homology with Arabidopsis DOF proteins, and established connections between some of these members and IMR genes using RNA-seq data. Additionally, molecular docking confirmed the binding interactions between these DlDOFs and the DOF binding sites in the promoter regions of IMR genes. The co-expression relationship between the two gene sets was further validated using q-PCR experiments. This study paves the way for research into iron metabolism pathways in bamboo and lays the foundation for understanding the role of DOF transcription factors in D. latiflorus.

Laser-Powder Directed Energy Deposition (DED-LB/Powder) is an additive manufacturing process that is gaining popularity in the manufacturing industry due to its numerous advantages, particularly in repairing operations. However, its application is often limited to case studies due to some critical issues that need to be addressed, such as the degree of internal porosity. This paper investigates the effect of the most relevant process parameters of the DED-LB/Powder process on the level and distribution of porosity. Results indicate that, among the process parameters examined, porosity is less affected by travel speed and more influenced by powder mass flow rate and laser power. Additionally, a three-dimensional finite element transient model was introduced, which was able to predict the development and location of lack-of-fusion pores along the building direction.

This study utilises NaOH to treat composite cementitious materials containing aeolian sand and zeolite powders, which were used to replace 50% of the cement in aeolian-sand concrete (ASC). The mechanical properties of treated ASC considerably improved, especially when the NaOH dosage was 4% by mass. After curing this sample (denoted as AAZC-4) for 28 d, its compressive strength improved by 17.2% and its split tensile was increased by 16.3%. Potassium feldspar and montmorillonite in zeolite powder and SiO2 in the sand were decomposed by OH− and combined with other elements to generate various silicate gels and A-type potassium zeolite crystals inside the concrete. Microscopic examination showed that the gels and crystals intertwined to fill the pores, decreasing (increasing) the percentage of large (small) pores, thus optimising the pore structure. This substantially improved the mechanical properties of ASC. Freeze–thaw salt-intrusion tests showed that the extent of mass loss, degree of damage and loss of compressive strength of AAZC-4 were similar to those of ordinary concrete but were reduced by 36.8%, 19% and 52.1%, respectively, compared with those of ASC. Therefore, AAZC-4 has sustainable working performance in the chloride ion permeable environment in cold and arid areas.

Infrastructure development is rapidly increasing, driving up demand for concrete, a key construction material. Cement and aggregate are essential constituents, with global cement production reaching 4.1 billion metric tons in 2011 and CO2 emissions hitting 1.7 billion metric tons by 2024, a significant contributor to carbon emissions. To address this, alternative constituents like Rice Husk Ash (RHA) and Animal Bone Powder (ABP) are proposed. With rice husk comprising 20% of rice weight and a substantial cattle population in Bangladesh, RHA and ABP offer promising alternatives. This study examines the benefits and limitations of incorporating RHA and ABP into cement, focusing on concrete strength and permeability. By replacing varying percentages of cement with RHA and ABP simultaneously, experiments evaluate their impact on concrete properties after 28 days of curing. The research aims to identify the optimal combination for sustainable concrete production, reducing environmental impact by curbing waste generation and pollution. Results show that compressive strength increases and permeability decreases with up to 5% replacement of RHA and ABP, highlighting their potential for enhancing concrete performance while mitigating environmental concerns.

Background: In response to inflammation, the absorption of nutritional iron is restricted. Multiple inflammation-related signaling pathways can lead to ferroptosis, an iron-dependent mechanism of programmed cell death. Since the pathophysiological significance of the presence and uptake of iron in chronic inflammation is still unknown, we tested the effect of a low iron diet on the clinical course of arthritis in the mouse model of collagen-induced arthritis (CIA). Methods: Six- to eight-week-old male DBA/1 mice were fed either a normal or a low iron diet starting three weeks before arthritis induction. From day four after the collagen-booster made on day 25, the development of arthritis was regularly monitored until the end of the experiment (day 34), using a standard clinical arthritis score. The complete blood count was determined as well as Fe2+, Fe3+, oxidized and reduced glutathione (GSH and GSSG) and malondialdehyde (MDA) in whole paw tissue by ELISA. Quantitative PCR was performed from whole paw tissue for glutathione peroxidase 4 and other key regulator genes of iron metabolism and ferroptosis. We used nonparametric tests to com-pare markers of iron metabolism and ferroptosis as well as nonlinear regression models for longitu-dinal data for signs of arthritis. Results: Mice fed a low iron diet showed a significantly less severe course of arthritis compared to mice fed a normal iron diet (p

: The activated carbons (ACs) derived from okara powder waste with high surface areas were modified with ammonia aqueous solution impregnation in an autoclave to enhance their CO2 adsorption properties toward CO2. The impregnated ACs were characterized in which surface chemical composition and properties of the ACs were analyzed by SEM-EDX, FTIR. Activated carbons were functionalized with ammonia aqueous solution (25%) through a hydrothermal process within 24; 48, and 72 hours. The adsorption performance of CO2 onto carbon samples was experimentally evaluated through a TPD CO2 measurement. FTIR spectra confirm the N-containing in N-modified activated carbons and the presence of the –C = O stretch and N-H groups. CO2 uptakes of N-modified activated carbons are 0.24; 1.78; 2.24 and 1.26 mmol/g, which are relatively comparable with those of activated carbons studied in in the literature.

The activated carbons (ACs) derived from okara powder waste with high surface areas were modified with ammonia aqueous solution impregnation in an autoclave to enhance their CO2 adsorption properties toward CO2. The impregnated ACs were characterized in which surface chemical composition and properties of the ACs were analyzed by SEM-EDS, FTIR. Activated carbons were functionalized with ammonia aqueous solution (25%) through a hydrothermal process within 24; 48, and 72 hours. The adsorption performance of CO2 onto carbon samples was experimentally evaluated through a breakthrough adsorption experimental setup at room temperature. FTIR spectra confirm the N-containing in N-modified activated carbons and the presence of the –C = O stretch and N-H groups. CO2 uptakes of N-modified activated carbons are 0.24; 1.47; and 1.20 mmol/g, which are relatively comparable with those of activated carbons studied in in the literature.

Several observations have shown that patients with polycythemia have iron deficiency. Our objectives were to report the prevalence of iron deficiency, to evaluate the diagnostic performance of serum ferritin in polycythemia vera and to describe the mechanisms of this association. This is a retrospective descriptive and analytical study carried out in the internal medicine department of the Henri Mondor Hospital, Aurillac, France. The study involved 114 patients with polycythemia, followed in the department from January 1, 2010 to December 31, 2021. To evaluate the diagnostic performance, the JAK2 mutation was considered as the gold standard of diagnosis. Thirty-three patients had polycythemia vera and 76 patients had secondary polycythemia. The mean age of the patients was 61.79 years (±15.44) with a sex ratio of 4.43. The overall prevalence of iron deficiency was 21.05%. The prevalence was 53% in polycythemia vera group and 1.32% in secondary polycythemia group. The risk of iron deficiency was high in polycythemia vera (OR=115; 95% CI [14.4-918.2], p<0.000). The sensitivity and specificity of serum ferritin were 52.63% and 100% respectively. Assessment of iron deficiency should be part of the initial evaluation of polycythemia. The presence of iron deficiency is specific for polycythemia vera.

Iron tailings are solid waste generated after the mining of iron mines, which have caused serious damage to the surrounding ecology and environment and have attracted widespread attention. By analyzing the formation causes, main components, and environmental effect mechanisms of iron tailings, the article systematically elaborates on the degree and mechanism of the harm of iron tailings to water bodies, atmosphere, soil, and ecosystems, and evaluates its impact on human health and sustainable development of society. On this basis, specific prevention and control measures have been proposed to reduce iron tailings emissions, realize resource recycling, and restore ecosystems. Research shows that iron tailings containing heavy metals can widely pollute the environment through dissolution and migration, and have significant biological toxicity effects. The research results can provide a theoretical reference for decision-making departments to formulate scientific and reasonable iron tailings disposal and ecological protection policies. It is recommended to strengthen specific research on the infiltration of toxic and harmful components in tailings in the future, and develop efficient and stable solidification technology, and vegetation-microbial joint restoration models to further reduce the ecological and environmental risks of iron tailings.

The iron roughneck is an automated equipment utilized for the connection and removal of drilling tools. This paper presents the design of an integrated iron roughneck, providing a detailed introduction to its clamp body structure, along with an analysis of its structural characteristics and performance requirements. The study delves into the integration mode and working characteristics of the clamping mechanism and spin buckle mechanism for the integrated upper clamp body structure of the iron roughneck. Additionally, this paper conducts an in-depth theoretical study on the spin buckle mechanism. Firstly, it analyzes the actual working condition of the spin buckle roller from two perspectives: contact theory and rolling friction theory, determining the structural form of the spin buckle roller. Secondly, it investigates the relative displacement between the spin buckle mechanism and the drilling tool, proposing a design method for the floating device mounted on the spin buckle roller and establishing the kinematic equation of the spin buckle roller under the influence of the floating device. Furthermore, the kinematic equations of the spin buckle roller under the influence of the floating device are established. Finally, a dynamics simulation experiment is performed to simulate the working process of the spin buckle mechanism under actual working conditions, analyzing the dynamics and kinematics of the spin buckle mechanism and obtaining the relevant parameter curves of the spin buckle mechanism and drilling tools. Through data comparison and analysis, the correctness of the theoretical analysis results and the rationality of the performance and structure of the spin buckle mechanism are verified.

Iron is an essential nutrient and necessary for biological functions from DNA replication and repair to transcriptional regulation, mitochondrial respiration, electron transfer, oxygen transport, photosynthesis, enzymatic catalysis, and nitrogen fixation. However, due to iron’s propensity to generate toxic radicals which can cause damage to DNA, proteins, and lipids, multiple processes regulate uptake and distribution of iron in living systems. Understanding how intracellular iron metabolism is optimized and how iron is utilized to regulate other intracellular processes is important to our overall understanding of a multitude of biological processes. One of the tools that the cell utilizes to regulate a multitude of functions is ligation of the iron-sulfur (Fe-S) cluster cofactor. Fe-S clusters comprised of iron and inorganic sulfur are ancient components of living matter on earth that are integral for physiological function in all domains of life. Here we will explore the ways in which the cell utilizes Fe-S clusters to sense the intracellular environment and respond to maintain equilibrium.

The study, conducted at the Department of Medicine, Maulana Azad Medical College and associated Lok Nayak Hospital, aimed to investigate the prevalence of iron deficiency anaemia among anaemic overweight and obese individuals. Fifty participants were included after screening and consent, undergoing socio-demographic assessment, clinical evaluation, and laboratory investigations. Middle to old-aged individuals predominated (Mean ± SD: 54.54 ± 11.32 years), with females comprising 62%. All subjects were obese (mean BMI: 37.27 ± 5.71 kg/m²), with common comorbidities including hypertension (68%), diabetes (36%), and obstructive sleep apnea-hypopnea syndrome (32%). Nutritional deficiencies, particularly iron deficiency, were prevalent, affecting 62% of subjects, with 48% having iron deficiency alone. Anemia of chronic illness was observed in 38%. Laboratory parameters showed low hemoglobin (8.53 ± 1.23 g/dL), MCV (78.75 ± 10.13 fL), and elevated ESR (20.56 ± 21.47 mm/hour) and CRP levels (4.71 ± 3.32 mg/dL), indicating inflammation. Correlation analyses revealed negative associations between BMI and serum iron/ferritin and positive associations with serum hepcidin. The study underscores the significance of addressing nutritional deficiencies and monitoring iron status in obese populations, suggesting potential associations between obesity and iron metabolism. Further research is needed to explore these relationships for clinical management implications.

Polymeric composites such as Poly-ether-ether-ketone (PEEK)/carbon fiber (CF) have been widely utilized due to outstanding performances such as high specific strength and specific modulus. The PEEK/CF components via powder-bed fusion additive manufacturing usually show brittle fracture behaviors induced by their poor interfacial affinity and inner voids. These defects are strongly associated with powder packing quality upon deposition. The particle dynamic model has been widely employed to study the interactions of particle motions. Powder property, bulk material property, and interfacial features of composite powders are key factors in the particle dynamic model. In this work, an efficient and systematic material evaluation is developed for composite powders to investigate their deposition mechanism. The discrete element method is utilized to simulate the dynamic behaviors of PEEK/CF composite powders. The powder properties, bulk material properties, and interfacial features of powders are calibrated and justified by experimental measurement, numerical simulation, and design of experiments. The particle dynamic model can well explain the powder flow behaviors and interactions. It reveals that the addition of short CF particles can assist the flow of PEEK powders and improve the packing quality of the composite powders.

For the last two decades, an increasing demand for low-cost adsorbents for drinking water treatment has been challenged in the rural areas of developing countries that have problems with arsenic (As) contamination. In this work, spent bleaching earth (SBE), a residual material that is formed during the process of refining vegetable oil, has been utilized to prepare the new magnetic adsorbent Fe-SBE/C by modifying its surface area through calcination and co-precipitation with iron. The experimental results demonstrate that Fe-SBE/C exhibits a substantial adsorption capacity towards both arsenite (As(III)) and arsenate (As(V)). Optimal pH conditions were found to be pH 10 for As(III) and pH 3 for As(V), resulting in adsorption percentages of 76.7% and 94.1%, respectively. Other experimental parameters such as calcination conditions, adsorbent dosage, iron-loading ratio, and the presence of co-existing ions were thoroughly investigated. The kinetic study revealed that the adsorption processes follow the Elovich and intraparticle diffusion models, suggesting a combined adsorption mechanism of boundary layer control and chemisorption. Furthermore, the isotherm followed the Langmuir model with a maximum adsorption capacity of 202.61 μg g-1 for As(III) and 187.61 μg g-1 for As(V). Through thermodynamic analysis and reinforcement by activation energy data, this research validates that the observed adsorption process is indicative through chemisorption. The regeneration study revealed the potential for multiple cycles of arsenic removal, highlighting the practical applicability of Fe-SBE/C in environmental contexts. In conclusion, the findings of this study underscore the efficacy of Fe-SBE/C in arsenic removal and present it as a promising and environmentally friendly solution for mitigating arsenic pollution.

Titanium-based metal-matrix composites manufactured by additive manufacturing offer tremendous lightweighting opportunities. However, processing high reinforcement content remains challenging. This study reports an improved manufacturing process for Ti-TiC enabling high reinforcement content and significant fracture strain concurrently: mechanical blending, followed by laser powder bed fusion and a single heat treatment. As-built microstructure shows both un-melted TiC particles and sub-stoichiometric TiC dendrites resulting from a partial dissolution of TiC particles. The heat treatment is shown to fully convert TiC dendrites into equiaxed TiC grains. Reduction of the C/Ti ratio in TiC during the process results in an increase in the reinforcement content, from a nominal 12 vol% to an effective 21.5 vol%. Ti-TiC tensile samples reached fracture strains of up to 1.7%, Young’s moduli of up to 149 GPa and ultimate tensile strengths of up to 827 MPa. Lower TiC initial powder size distributions displayed the best mechanical performance.

Silver powder, as the primary component of solar silver paste, significantly influences various aspects of paste performance, including printing, sintering, and conductivity. Silver powders prepared using the liquid-phase reduction method exhibit different microstructures depending on whether the growth process is dominated by aggregation or crystalline growth. This study explores the impact of different silver powder microstructures on packing density and sintering activity. It is observed that polycrystalline aggregated silver powder possesses higher surface energy, lower packing density, and greater sintering activity. Investigation into the influence of different silver powders on the electrical conductivity, adhesion, and structural density of silver paste reveals that polycrystalline aggregated silver powder is more suitable for lower sintering temperature pastes, whereas crystalline growth-type silver powder is better suited for higher sintering temperature pastes, resulting in a denser sintered silver layer. Finally, an analysis of the impact of various silver powders on the aspect ratio and electrical performance of solar cell silver grid lines yields higher aspect ratios (0.40) and photoelectric conversion efficiency (19.26%).

Fused deposition modeling (FDM) is a rather new technology in the production of personalized dosage forms. Melting and printing of polymer–active pharmaceutical ingredient (API) – mixtures can be used to produce oral dosage forms with different dosage as well as release behavior. This process is utilized to increase the bioavailability of pharmaceutically relevant active ingredients that are poorly soluble in physiological medium by transforming them into solid amorphous dispersions (ASD). Release from such ASDs is expected to be faster and higher compared to the raw materials and thus enhance bioavailability. Printing directly from powder while forming ASDs was realized. Different techniques to change release patterns as well as a non-destructive way for determination of API distribution were shown. By measuring the melt viscosities of mixtures printed a rheological model for the printer used is proposed.

Soil carbon (C) cycling under anoxic conditions is mechanistically linked to dissimilatory iron (Fe) reduction, which could be regulated by exogenous dissolved organic matter (DOM). However, the impact of complex exogenous DOM on soil microbial activity and C-Fe coupling in paddy soils remains underexplored. With a 100-day microcosm experiment, we determined that the molecular composition of DOM derived from organic fertilizers and biochar on paddy soil affects soil microbial community, Fe reduction, and C emissions. Our results indicated that biochar-DOM significantly promoted Fe reduction and accelerated CH₄ and CO₂ emissions, and organic manure-DOM increased soil CO₂ emissions, which was closely related to the molecular composition of exogenous DOM. DOM molecules with high aromaticity (AI_mod) and high DBE, including lignins-vascular plant-derived polyphenols, lignins-polycyclic aromatics (PA), and condensed aromatics-PA, promoted soil Fe reduction and CH₄ emissions by enriching soil Fe-reducing bacteria (FeRB), reducing methanotrophs, and facilitating r-strategists at the early stage of incubation. Conversely, DOMs with low AI_mod, low DBE and high H/C, such as lignins-highly unsaturated and phenolic compounds and proteins-aliphatic compounds, enhanced CO₂ emissions by facilitating recalcitrant C degradation and CH₄ oxidation at the late stage of incubation. In conclusion, our study highlights the importance of the molecular composition of DOMs derived from organic amendments in regulating soil Fe reduction and C emissions. The findings offer novel insights into the effective utilization of agricultural resources and the mitigation of soil C emissions.

Ferritin is an indirect marker for total body iron stores. Comparison of the ferritin concentrations in the meconium with the concentrations of proteins regulating iron metabolism could aid better understanding of principles behind the adjustment between the fetal iron pool and newborn body size. Ferritin, transferrin, haptoglobin, ceruloplasmin, lactoferrin, myeloperoxidase, neutrophil gelatinase-associated lipocalin (NGAL) and calprotectin concentrations were measured by ELISA in meconium samples from 122 neonates. The neonates were classified according to the meconium ferritin tertiles and the values were collated with the meconium concentrations of other proteins and newborn body weight and length measurements. Increasing ferritin concentrations in meconium in consecutive tertiles (p < 0.05) were parallel to increased NGAL concentrations (p < 0.05). The interrelationships between the meconium concentrations of transferrin, haptoglobin and NGAL as well as between myeloperoxidase, calprotectin and lactoferrin are maintained in all subsequent tertiles of ferritin concentrations, (p < 0.05). In contrast to ferritin, increasing meconium NGAL concentrations in consecutive tertiles were linked to increased concentrations of transferrin, haptoglobin, lactoferrin and myeloperoxidase (p < 0.05) and of calprotectin, ferritin and ceruloplasmin (p < 0.1). Meconium ceruloplasmin concentrations correlate exclusively with neutrophil granule proteins, i.e. myeloperoxidase, NGAL, lactoferrin and calprotectin (p < 0.05). Meconium ferritin concentrations negatively correlates with birth weight (r= -0.20) and length (r= -0.31) of neonates, whereas NGAL concentrations just with birth length (r= -0.26). The remaining proteins did not show such relationships with the size of the newborn. High meconium concentrations of both ferritin and NGAL may specifically characterize neonates of smaller size. High meconium concentrations of both ferritin and NGAL may specifically characterize neonates with lower body measurements. Correlations between meconium transferrin, haptoglobin and NGAL may confirm the interrelationships of these proteins for proper iron control and transport in the intrauterine environment. Meconium ceruloplasmin concentrations may reflect the control of neutrophil activity in utero.

Iron metabolism plays a crucial role in the management of hemoglobinopathies, particularly in conditions such as β-thalassemia and sickle cell anemia (SCA). This paper describes the mechanisms of iron overload in patients with transfusion-dependent thalassemia (TDT), non-transfusion-dependent thalassemia (NTDT), and SCA, highlighting the distinct paths leading to iron accumulation in each condition. The primary focus of this review article is on the role of genetic modifiers influencing iron metabolism and the variability in iron overload presentation among patients. Genetic mutations in genes such as HFE, HAMP, TFR2, SLC40A1, and others significantly impact iron regulation. These modifiers can exacerbate or ameliorate iron overload, and understanding these genetic factors is important for explaining the diverse disease severity and differences in the mechanism and clinical presentation of iron overload in these patients. The ongoing INHERENT study aims to further elucidate the influence of these genetic modifiers through a comprehensive genome-wide association study, potentially leading to novel therapeutic interventions for managing iron homeostasis in hemoglobinopathy patients.

Hybrid reinforcement in a composite material (CM), in many situations, allows better govern material mechanical properties. Polymer matrix CM plate is reinforced with small particles and macro-fibers. Particles are oil shale ash (OSA) powder, macro-fibers – basalt fiber threads im-pregnated by matrix material. With the goal to find out elastic properties of the matrix- polymer with OSA, samples with its different concentrations were experimentally fabricated and their elastic properties were experimentally measured. Obtained data were used in numerical model-ling. Was observed polymer matrix composite slab, reinforced with OSA and three-dimensional (3D) basalt fiber fabric. Fabric are forming threads impregnated by matrix (polymer resin mixed with OSA particles). Damage accumulation in the stretched slab was modelled. Impregnated thread, in the modelling, is observed as a macro-fiber (MF) with averaged elastic properties. With the load increase MF in the material began to break. At first, appeared isolated single breaks. A probabilistic sequential MF rupture accumulation model was accepted and numerical-ly realized. The geometry of the reinforcing knitted fabric was modeled using the Leaf and Glaskin approach. In the knitted fabric highly, stressed MF cross-sections are observed as po-tential location where thread breakage can occur. If one thread breaks, the cross-sections of the adjacent threads experience the overload caused by this rupture. More overloaded crossection in the adjacent overloaded thread breaks and we obtain two adjacent broken MF designated as a defect with the size j=2. The probabilities of obtaining defect consisting of at least 2, 3, … j adjacent broken MF in the plate were calculated. The calculations continued until the rupture process becomes unstable (j→∞). The overstresses on adjacent threads in the CM were calculat-ed using the FEM three-dimensional numerical approach. Analytical and stochastic methods were used for the load-carrying capacity determination and different size defects accumulation in the hybrid composite material (HCM) plate. Also, was calculated the probability of the plate rupture.

This study outlines a 3-step production process for Ti-TiC Metal Matrix Composite (MMC) employing powder Mechanical Blending, Laser Powder Bed Fusion (LPBF), and a heat treatment. A TiC fraction of more than 20 vol% was formed in-situ through the reaction of titanium with carbon during the LPBF process. The manufactured MMC pieces showed a record stiffness and fracture strain combination. The LPBF energy density impacted strongly porosity type. The as-built microstructure displayed an homogeneous distribution of sub-stoichiometric TiC dendrites which were fully converted into equiaxed TiC grains during the heat treatment. The TiC C/Ti ratio was found to be close to 0.5, resulting in an effective reinforcement content nearly twice the one expected for stoichiometric TiC, leading to stronger reinforcement. The mechanical analysis revealed a Young’s modulus of up to 149 GPa and an ultimate tensile strength of up to 770 MPa, indicating a 27% and 34% improvement, respectively, compared to commercially pure Titanium produced by LPBF and heat treated in the same conditions. A fracture strain of up to 2.8% was achieved. The combination of in-situ formation of defect-free TiC reinforcement and subsequent heat treatment enables to reach an exceptional ductility, considering the 20 vol% reinforcement content.

Epoxy powders offer a low-cost means of manufacturing thick section composite parts, such as those found in wind and tidal turbines. Currently, their processing cycle includes a lengthy drying stage (≥ 15 h) to remove ambient moisture. This prevents void defect formation and, thereby, a reduction in mechanical properties, however, it constitutes up to 60% of the processing time. Little research has been published on the study of this process or its optimisation. Experimental and simulated analyses are used to investigate the effects of hygroscopicity in epoxy powder composites. In particular, focus is given to the drying process, which is used to prevent void defect formation and, thereby, a reduction in mechanical properties. As such, tests are performed to quantify the void content of dried and undried laminates, and to measure its impact on transverse flexural strength. Dynamic vapour sorption analysis is used to study the sorption behaviour of the epoxy powder. Sorption data is fitted to a modified linear driving force model, and then implemented in existing process simulations tools. The drying of a thick epoxy powder composite section is simulated to investigate the influence of powder sintering on the duration required for drying. It is shown that the epoxy powder is slightly hygroscopic (1.36 wt%) and exhibits sorption behaviour that is characteristic of glassy polymers. This results in up to 4.8% voids (by volume) if processed in an undried state, leading to a 43% reduction in transverse flexural strength. Process simulations reveal that a standard drying cycle prematurely sinters the powder; inhibiting moisture release. By maintaining a powder state, simulations show that the drying cycle can be reduced to 5 h.

This study explores novel techniques to improve the detection accuracy of skarn iron deposits using advanced image processing methodologies. Leveraging the capabilities of Aster image, Band Ratio (BR) images, and Principal Component Analysis (PCA), alongside the power of 3D Convolutional Neural Networks (3D-CNN), the research aims to enhance the precision and efficiency of ore detection in complex geological environments. The proposed method employs a specific 3D-CNN architecture, accepting input as a 7×7×C image patch, where C represents the combined number of selected Aster image bands, Principal Component (PC) bands, and computed BR images. To evaluate the accuracy of the proposed method, five distinct image bands combinations, including the proposed bands combination, were tested and evaluated based on the overall accuracy (OA), average accuracy (AA), and kappa coefficient. The results demonstrated that while the incorporation of BR images alongside Aster bands initially seemed promising, it introduced significant confusion in certain classifications, leading to unexpected mis-classification rates. Surprisingly, utilizing solely Aster bands as input parameters yielded higher accuracy rates (OA= 93.13%, AA = 91.96%, Kappa = 90.91%) compared to scenarios involving the integration with band ratios (OA = 87.02%, AA = 79.15, and Kappa = 82.60%) or the integration of BR images to PC bands (OA= 87.78%, AA = 82.39%, Kappa = 83.81%). However, the amalgamation of Aster bands with selected PC bands showed slight improvements in accuracy (OA= 94.65%, AA = 92.93%, Kappa = 93.45%), although challenges in accurately classifying certain features persisted. Ultimately, the proposed combination of Aster bands, PC bands, and BR images (proposed bands combination) presented the most visually appealing and statistically accurate results (OA = 96.95%, AA= 94.87%, and Kappa = 95.93%), effectively addressing misclassifications observed in the other combinations. These findings underscore the synergistic contributions of each of the Aster bands, PC bands, and BR images, with Aster bands proving pivotal for optimal skarn classification, PC bands enhancing intrusions classification accuracy, and BR images strengthening wall rock classification accuracy. In conclusion, the proposed combination of input image bands emerges as a robust and comprehensive methodology, demonstrating unparalleled accuracy in the remote sensing detection of skarn iron minerals.

Iron and zinc are essential micronutrients required for growth and health. Deficiencies of these nutrients are highly prevalent among populations, but can be alleviated by supplementation. Cross-sectional studies in humans showed positive association of serum zinc levels with hemoglobin and markers of iron status. Dietary restriction of zinc or intestinal specific conditional knock out of ZIP4 (SLC39A4), an intestinal zinc transporter, in experimental animals demonstrated iron deficiency anemia and tissue iron accumulation. Similarly increased iron accumulation has been observed in cultured cells exposed to zinc deficient media. These results together suggest a potential role of zinc in modulating whole body iron metabolism. Studies in intestinal cell culture models demonstrate that zinc induces iron uptake and transcellular transport via induction of divalent metal iron transporter-1 (DMT1) and ferroportin (FPN) expression, respectively. It is interesting to note that intestinal cells are exposed to very high levels of zinc through pancreatic secretions, which is a major route of zinc excretion from the body. Therefore, zinc appears to be modulating the iron metabolism possibly via regulating the DMT1 and FPN1 levels. Herein we critically reviewed the available evidence to hypothesize novel mechanism of Zinc-DMT1/FPN axis in regulating intestinal iron absorption and tissue iron accumulation to facilitate future research aimed at understanding the yet elusive mechanisms of iron and zinc interactions.

The carbonyl iron particles were dispersed in a polychloroprene rubber (CR) matrix under an external magnetic field for practical application as microwave absorption composites film. The film prepared under external magnetic field with a thickness of only 0.54 mm showed least reflection loss of -15.98 dB and the reflection loss value less than -10.0 dB over the frequency range of 11.4~14.8 GHz. In comparison with the microwave absorption properties of calculation by transmission line theory based on the tested relative complex permittivity and permeability and film prepared by general route without external magnetic field, the film made with external magnetic field exhibited more excellent microwave absorption properties, strongly depending on the increment of anisotropy and rearrangement of magnetic particles. The results indicated the composite film made under external magnetic field have excellent microwave absorption properties, which suggest that the composites thin film could be used as a thinner and lighter microwave absorber.

Metals play vital roles in biological systems, with iron/heme being essential for cellular and metabolic functions necessary for survival and/or virulence in many bacterial pathogens. Given the rise of bacterial resistance to current antibiotics, there is an urgent need for the development of non-toxic and novel antibiotics that do not contribute to resistance to other antibiotics. Gallium, which mimics iron, has emerged as a promising antimicrobial agent, offering a novel approach to combat bacterial infections. Gallium does not have any known functions in biological systems. Gallium exerts its effects primarily by replacing iron in redox enzymes, effectively inhibiting bacterial growth by targeting multiple iron/heme-dependent biological processes and suppressing the development of drug resistance. The aim of this review is to highlight recent findings on the mechanisms of action of gallium and provide further insights into the development of gallium-based compounds. Understanding the mechanisms underlying gallium’s biological activities will enhance its therapeutic application across various medical fields, offering promising avenues for the treatment of infectious diseases, cancer, and inflammatory conditions.

Integrating nanomaterials like carbon nanotubes (CNTs) and iron oxide (Fe₃O₄) into epoxy composites has significant interest due to their potential to enhance mechanical properties. This study evaluates the impact of dispersion quality on the mechanical performance of CNT/Fe₃O₄/Epoxy composites, comparing stirring and sonication methods at three different loadings: 0.1, 0.3, and 0.5 wt.%. Tensile testing revealed that sonicated composites consistently outperformed stirred composites, with a significant increase in elastic modulus and ultimate tensile strength (UTS). However, fracture strain decreased in both composite types compared to pure epoxy, with sonicated composites experiencing a more significant reduction than stirred composites. These results underscore the importance of high-quality dispersion for optimizing mechanical properties.

The paper provides a discussion on the results of studies of the effect exerted by combined degradation factors typical of four types of wear: abrasion, impact-abrasion, tribocorrosion, and impact-abrasion-corrosion, conducted for chain wheels made of Ni-Cu alloyed Austempered Ductile Iron. The studies consisted in determining the content of retained austenite in the structure of the cast irons in question, establishing the measures of wear following wear testing, and identifying basic surface degradation mechanisms observed in the chain wheels tested following multifactorial wear processes. The chain wheels made of ADI were found to have sustained the greatest damage under the impact-abrasion-corrosion (three-factor) wear scenario, while the wear was least advanced in the abrasion (one-factor) wear case. Another observation derived from the studies is that the combined effect of dynamic forces, corrosion, and quartz sand-based abrasives causes increased surface degradation in the cast iron grades taken into consideration compared to processes characterised by a reduced number of degradation factors (i.e. one- or two-factor wear processes). Additional hardness tests and XRD analyses have revealed a distinctive effect attributable to combined degradation factors on the surface hardness increase value and implied that bench testing was followed by phase transition.

This work investigated the isothermal holding time dependence of the densification, microstructure, weight loss and tensile properties of Fe-Mn-Si powder compacts. Elemental Fe, Mn and Si powder mixtures with a nominal composition of Fe-28Mn-3Si (in weight percent) were ball milled for 5h and subsequently pressed under a uniaxial pressure of 400 MPa. The compacted Fe-Mn-Si powder mixtures were sintered at 1200 ℃ for 0, 1, 2 and 3 h, respectively. In general, the density, weight loss and tensile properties increased with the increase of isothermal holding time. A significant increase in density, weight loss and tensile properties occurred in the compacts isothermally holding for 1 h, as compared to those with no isothermal holding. However, further extension of isothermal holding time (2 and 3 h) only played a limited role in promoting the density and tensile properties. The weight loss of the sintered compacts was mianly caused by the sublimation of Mn in Mn depletion region on the surface layer of the sintered Fe-Mn-Si compacts. The length of the Mn depletion region increased as isothermal holding time increased. A single α-Fe phase was detected on the surface of all the sintered compacts, and the locations beyond the Mn depletion region were comprised of a dual dominant γ-austenite and minor ε-martensite.

Sideroflexins (SLC56 family) are highly conserved multi-spanning transmembrane proteins inserted in the inner mitochondrial membrane in eukaryotes. Few data are available on their molecular function but, since their first description, they were thought to be metabolite transporters probably required for iron utilization inside the mitochondrion. Such as numerous mitochondrial transporters, sideroflexins remain poorly characterized. The prototypic member SFXN1 has been recently identified as the previously unknown mitochondrial transporter of serine. Nevertheless, pending questions on the molecular function of sideroflexins remain unsolved, especially their link with iron metabolism. Here, we review the current knowledge on sideroflexins, their presumed mitochondrial functions and the sparse - but growing - evidence linking sideroflexins to iron homeostasis and iron-sulfur cluster biogenesis. Since an imbalance in iron homeostasis can be detrimental at the cellular and organismal levels, we also investigate the relationship between sideroflexins, iron and physiological disorders. Investigating Sideroflexins’ functions constitutes an emerging research field of great interest and will certainly lead to main discoveries on mitochondrial physiopathology.

Electromobility promises to efficiently mitigate consequences of increasing traffic volume and its accompanied greenhouse gas emissions. On an individual level, electrified bikes allow emission free electrified mobility at moderate costs and consequently their stock has increased significantly in recent years. This simultaneously increases the demand for spare parts, which are often manufacturer or application-specific, and due to many variants, challenging to provide for the market. This article evaluates powder-based and extrusion-based metal additive manufacturing of a typical electrified bike component to demonstrate an alternative spare parts supply. The investigation demonstrates how these parts can be additively manufactured function equivalent and with sufficient mechanical properties, also taking economical aspects into account. Furthermore, the needed resources and related environmental consequences for metal-based additive manufacturing spare-part production are compared for both process routes. The results show that both routes are capable of producing spare-parts at comparatively same mechanical performance and resource costs, while needed resources such as energy, gases and manufacturing time are significantly lower for powder-based, respectively machine costs for extrusion-based additive manufacturing. Therefore, additive manufacturing offers a promising opportunity to produce parts in small quantities resource efficient and rapidly.

In the realm of metal steel and iron manufacturing, there is a constant drive to optimize production efficiency and enhance the quality of the final products. This abstract explores a paradigm shift in this industry through the utilization of Computational Fluid Dynamics (CFD) as a powerful tool for achieving these goals .The study focuses on various critical aspects of the manufacturing process. Firstly, it delves into three-phase processes such as slag and gas entrainment in liquid steel, which have a significant impact on the overall product quality. Understanding and optimizing these processes is crucial to ensure the desired chemical composition and physical properties of the final metal.The abstract investigates the role of CFD in vacuum degassing, a process that plays a pivotal role in removing impurities, such as hydrogen and oxygen, from the liquid steel. By leveraging CFD to simulate and analyze the fluid flow patterns, researchers and engineers can design more efficient vacuum degassing systems, leading to improved product purity and reduced waste.Another crucial aspect explored in this abstract is the alloy melt and mixing process. By employing CFD simulations, researchers can gain insights into the movement of different alloy components and optimize their distribution within the melt. This aids in achieving the desired alloy composition, ensuring uniformity, and enhancing the mechanical properties of the final product.In addition, the study delves into the movement and flotation of inclusions, which are unwanted impurities present in the metal. CFD can be utilized to model and analyze the behavior of these inclusions, enabling engineers to design efficient strategies for their removal, thereby enhancing the purity and integrity of the final product.Moreover, the abstract considers the impact of melt temperature losses, which can occur during different stages of the manufacturing process. By employing CFD, it becomes possible to understand and mitigate these temperature losses, leading to improved energy efficiency and better control over the manufacturing parameters.Part 1 of this abstract critically evaluates the use of CFD in iron making, analyzing its benefits and limitations. It highlights how CFD can aid in process optimization, improving the understanding of complex phenomena involved in iron making, and ultimately leading to enhanced production efficiency.Part 2 focuses on the application of CFD in steel making and steel operation. It explores the fluid flow dynamics during different stages of steel production, including refining, casting, and rolling. By leveraging CFD, engineers can optimize these processes, leading to improved product quality, reduced defects, and increased productivity.This abstract demonstrates the transformative potential of Computational Fluid Dynamics in metal, steel, and iron manufacturing. By utilizing CFD as a tool to model and analyze complex fluid flow phenomena, researchers and engineers can revolutionize the production process, maximizing efficiency, and ensuring high-quality end products.

Iron plays a critical role in lung infections due to its function in the inflammatory immune response but also as an important factor for bacterial growth. Iron chelation represents a potential therapeutic approach to inhibit bacterial growth and pathologically increased pro-inflammatory mediator production. The present study was designed to investigate the impact of the iron chelator, DIBI, in murine lung infection induced by intratracheal Pseudomonas aeruginosa (strain PA14) administration. DIBI (80mg/kg) was given by intraperitoneal injection either as a single dose immediately after PA14 administration or a double dose (second dose 4 h after PA14 administration). The results showed that lung NF-κBp65 levels, as well as levels of various inflammatory cytokines (TNFα, IL-1β, IL-6) both in lung tissue and bronchoalveolar lavage fluid (BALF), were significantly increased 24h after PA14 administration. Single-dose DIBI did not affect the bacterial load or inflammatory response in the lungs or BALF. However, two doses of DIBI significantly decreased bacterial load, attenuated NF-κBp65 upregulation, reduced inflammatory cytokines production, and relieved lung tissue damage. Our findings support the conclusion that the iron chelator, DIBI, can reduce lung injury induced by P. aeruginosa, via its anti-bacterial and anti-inflammatory effects.

CoCrFeNiMn high-entropy alloy coatings were prepared on compacted graphite iron（CGI） through plasma cladding to strength the CGI substrate. The effects of heat treatment temperatures and times on the microstructure and mechanical properties of the CoCrFeNiMn coatings were investigated. After heat treatment, a single FCC phase was remained in the coating as compared to the deposited one, with smaller dendrites, larger dendritic spacing and more Cr-rich compounds precipitated between dendrites. The coatings’ microhardness was increased after heat treatment. After heat treated at 660°C for 90 minutes, the coating had the highest microhardness of 563±6.9 HV0.2, the lowest frictional coefficient of 0.71 and the smallest wear mass loss of 1.12 mg, and it had the best wear resistance.

Iron is the most abundant micronutrient in plant mitochondria and it has a crucial role in biochemical reactions involving electron transfer. It has been described in Oryza sativa that Mitochondrial Iron Transporter (MIT) is an essential gene and that knockdown mutant rice plants have a decreased amount of iron in mitochondria, strongly suggesting that OsMIT is involved in mitochondrial iron uptake. In Arabidopsis thaliana, two genes encode MIT homologues. In this study, we analyzed different AtMIT1 and AtMIT2 mutant alleles, confirming that individually AtMIT1 nor AtMIT2 genes are essential. When we generated crosses between Atmit1 and Atmit2 alleles we were able to isolate homozygous double mutant plants. Interestingly, homozygous double mutant plants were obtained only when mutant alleles of Atmit2 with the T-DNA insertion in the intron region were used for crossings, and in these cases a correctly spliced AtMIT2 mRNA was generated, although at a low level. Atmit1 Atmit2 double homozygous mutant plants, which were knockout for AtMIT1 and knockdown for AtMIT2, were grown and chacterised in iron sufficient conditions. Pleiotropic developmental defects were observed including abnormal seeds, increased number of cotyledons, slow growth rate, pinoid stems, defects in flower structures and reduced seed set. We observed a possible phenomenon of T-DNA suppression in the next generation of Atmit1 Atmit2 double homozygous mutant plants, correlating with an increased splicing of the AtMIT2 intron containing the T-DNA. Molecular analysis of gene expression markers for mitochondrial and oxidative stress showed that Atmit1 Atmit2 double homozygous mutant plants express a degree of mitochondrial perturbation. A RNA-Seq study was performed and we could identify more than 760 genes differentially expressed in Atmit1 Atmit2, including genes involved in iron transport, coumarin metabolism, and hormones metabolism, transport and signaling. Our data suggest that some of the phenotypes observed in Atmit1 Atmit2 double homozygous mutant plants are mediated by defects in auxin homeostasis.

The dynamic equilibrium of iron homeostasis has an important role in sustaining metabolic and neurological functions during human life. Iron excretion is modest and unregulated hence this overall equilibrium is tightly regulated in normal conditions by increasing deficient or limiting excessive iron assimilation. Here we focus on neural tissue overload, dyshomeostasis that is preceded by excessive assimilation, disturbances in internal homeostasis or both. Normal steps in iron homeostasis include its uptake across the apical membrane of the enterocytes in a mildly acidic duodenal milieu by the major importer of ferrous iron, Divalent Metal Transporter 1 (DMT1) (Nramp2/DCT1/SLC11A2, solute carrier family 11 member 2) [1, 2], responsible for the uptake of Non-Transferrin Bound Iron (NTBI) and divalent metals [3], passage through enterocytes bound to a chaperone and crossing the basal membrane via the only known cellular ferrous iron exporter, ferroportin [4] with the iron bound to transferrin (Tf) as it exits. Cells in peripheral tissues largely utilize circulating iron after uptake by receptor-mediated endocytosis of Tf-bound Iron [5]. Derangement of duodenal NTBI absorption of iron and heavy metals is influenced by systemic iron metabolism associated with inflammation that leads to iron accumulation into peripheral tissues and potential development of neurodegenerative diseases, involving distribution and fine regulation of DMT1 also in the central nervous system, where inflammatory-related acidosis influences DMT1 uptake, via its action as a proton cotransporter. Pharmacological strategies to inhibit NTBI transport selectively will be illustrated in relationship to protection, particularly neuroprotection, against iron overload associated with acidosis, inflammation, neuroinflammation and subsequent neurodegeneration.

The adulteration of goat milk powder occurs frequently, cattle-derived and soybean-derived ingredients are common adulterants in goat milk powder. However, simultaneously and rapidly detecting cattle-derived and soybean-derived components is still a challenge. high throughput and efficient screening method for adulteration detection is need. In this study, a rapid method was developed to detect the adulteration of common cattle-derived and soybean-derived components simultaneously in goat milk powder by combining the CRISPR/ Cas12a system with recombinant polymerase amplification (RPA). A dual DNA extraction method was employed, primers and crRNA for dual detection were designed and screened, and a series of condition optimizations were carried out in this experiment. The optimized assay can rapidly detect cattle-derived and soybean-derived components in 40 min. The detection limits of both cattle-derived and soybean-derived components were 1% (w/w) for the mixed adulteration models. The established method was applied into a blind survey of 55 commercially available goat milk powder products. The results showed that 36.36% of the samples contained cattle-derived or soybean-derived ingredients, which revealed the noticeable adulteration situation in the goat milk powder market. This study realizes a fast flow of dual extraction, dual amplification and dual detection of cattle-derived and soybean-derived components in goat milk powder for the first time. It can be used for high-throughput and high-efficiency on-site primary screening of goat milk powder adulterants, and provide a technical reference for combating with food adulteration.

Combining modern thermodynamics theory branches, including finite time thermodynamics or entropy generation minimization, constructal theory and entransy theory, with metallurgical process engineering, this paper provides a new exploration on generalized thermodynamic optimization theory for iron and steel production processes. The theoretical core is to thermodynamically optimize performances of elemental packages, working procedure modules, functional subsystems, and whole process of iron and steel production processes with real finite-resource and/or finite-size constraints with various irreversibilities toward saving energy, decreasing consumption, reducing emission and increasing yield, and to achieve the comprehensive coordination among the material flow, energy flow and environment of the hierarchical process systems. A series of application cases of the theory are reviewed. It can provide a new angle of view for the iron and steel production processes from thermodynamics, and can also provide some guidelines for other process industries.

Chromium (Cr) metal has garnered significant attention in alloy systems owing to its exceptional properties, such as high melting point, low density, and superior oxidation and corrosion resistance. However, its processing capabilities are hindered by the high Ductile-Brittle Transition Temperature (DBTT). Recently, powder bed fusion-laser beam for metals (PBF-LB/M) has emerged as a promising technique, offering the fabrication of net shapes and precise control over crystallographic texture. Nevertheless, research investigating the mechanism underlying crystallographic texture development in pure Cr via PBF-LB/M still needs to be conducted. This study explores the impact of scan speed on relative density and crystallographic texture. At the optimal scan speed, an increase in grain size attributed to epitaxial growth was observed, resulting in the formation of cubic texture. Consequently, a reduction in High Angle Grain Boundaries (HAGB) was achieved, suppressing defects such as cracks and enhancing relative density up to 98.1%. Furthermore, with increasing densification, Vickers hardness also exhibited a corresponding increase. These findings underscore the efficacy of PBF-LB/M for processing metals with high DBTT properties.

One consequence of the global technological advancement in conventional metallurgy is the fast depletion rate of valuable minerals, which are also becoming increasingly difficult to find in pure and economically viable forms. This has spurred more interest in technologies that investigate ability of different microorganisms to mobilize valuable metals from their ores via diverse metabolic processes. This study was carried out therefore to isolate, identify and characterize iron solubilizing bacteria from Iron stones of Agbaja iron ore mining site of Kogi State, Nigeria. Crushed samples in the range of 0.25µm and 0.75µm particle sizes were cultured in a modified 9k media to facilitate bacterial growth and pure cultures were then isolated and sub-cultured for further bioleaching studies. Morphological and biochemical analysis suggests that some of the bacteria identified are members of Acidithiobacillus spp, Pseudomonas spp, and Leptospirillum spp. Studies conducted on pure cultures and mixed consortium of the identified organisms shows that a mixture of the three organisms leached iron ore to about 96.16%. Also results of growth pattern due to bacteria countafter 24-72hours of incubation ranged between 0.1×10³ cfu/ml and 12.3 ×10³ cfu/ml for Acidithiobacillus spp. The need to explore the molecular characteristics of these organisms with a view to generating more information on the quality/quantity of their DNA for future cloning activities was also investigated in this work. DNA was extracted using zymo fungal/bacterial extraction mini prep kit ^TM (cat #6001) and subsequently subjected to 1% agarose gel electrophoresis. Visible bands were obtained with Alpha Innotech Gel Documentation Machine. DNA amplification was carried out using a pettier based thermo cycler PCR machine and electrophoresed on 1.5% agarose gel. Results of the PCR shows a visible band corresponding to 1.5kbp using this primer 27F (5¹-GAGTTTGATCCTGGCTCAG-3¹) and 1492R (5^1-GGTTACCTTGTTACGACT-3¹). DNA purity check shows two of the bacteria possess very good qualities for sequencing for further molecular analysis.

Goat milk is a nutritious food, with high levels of vitamins and minerals. In this context, there is a growing need to improve preservation techniques. Thus, the present work was developed with the aim of drying goat milk using a spray dryer. Chemical, physical, and physicochemical analyses of powdered goat milk and reconstituted goat milk were performed, as well as the characterization of raw goat milk. The statistical model used was the full factorial design 2³ + 3, observing the Pareto Diagram and Analysis of Variance to study the effect of atomization frequency (Hz), inlet temperature (°C), and peristaltic pump rotation (rpm) on the responses for the powdered and reconstituted product. The planning was executed with eleven trials, including nine different trials and three central points. For the analysis of the planning at a 95% confidence level, the Statistica 8.0 software was used. The results showed that atomization frequency and inlet temperature had the greatest effect on the powdered product and the reconstituted food, respectively. Therefore, the importance of drying this food is evident as it offers several advantages for the food industry and consumers.

Vitamin D and iron deficiencies are the most prevalent micronutrient deficiencies among women of reproductive age (WRA) in Morocco. Recent studies suggest that Vitamin D deficiency (VDD) may reduce iron bioavailability necessary for erythropoiesis, potentially leading to iron deficiency (ID) and anemia. This study investigates the association between vitamin D status, iron levels, and anemia risk among Moroccan WRA aged 18-49 years. A cross-sectional study was conducted with 463 participants. Serum levels of 25(OH)D, blood count parameters, iron, ferritin, C-reactive protein, and creatinine were measured. Lifestyle factors, including dietary intake, sun exposure, and physical activity, were evaluated using validated questionnaires, and anthropometric data were collected. Linear and logistic regression models assessed the relationships between variables, while Receiver Operating Characteristic (ROC) curve analysis evaluated the predictive accuracy of VDD for ID and anemia. VDD (25(OH)D &lt; 20 ng/ml) was significantly associated with lower levels of hemoglobin, hematocrit, red blood cells, and ferritin (all p &lt; 0.01), suggesting a role of vitamin D in erythropoiesis and iron storage. Multivariate logistic regression showed that VDD increased the risk of anemia (OR: 7.17, 95% CI: 3.19-19.28, p &lt; 0.001), ID (OR: 2.20, 95% CI: 1.32-3.77, p = 0.007), and IDA (OR: 4.10, 95% CI: 1.73-12.08, p = 0.004). Dietary iron intake was inadequate among all participants, with minimal protective effect against anemia and ID (β(SE): -0.08(0.03), p = 0.030 and β(SE): -0.05(0.02), p=0.037 respectively). ROC analysis demonstrated moderate discriminative power for VDD in diagnosing IDA and anemia (AUC: 0.643 and 0.603) but reduced accuracy for ID (AUC: 0.575). This study identifies VDD as a significant risk factor for impaired iron status and anemia among Moroccan WRA, underscoring the need for targeted nutritional interventions and further research to explore effective prevention strategies.

Non-compliance with iron supplementation consumption contributes to the high rate of anemia among adolescent girls in Indonesia. This study explores the barriers and enablers perceived by adolescent girls regarding regular iron supplement consumption. Using a qualitative design, eight focus group discussions (FGD) were conducted in Makassar and Padang involving 32 girls grade 8 and 9 from four junior high schools. Data on perceived barriers and enablers were collected using a social cognitive theory framework and analyzed thematically. The average age of the informants was 13,65±0,60 years. Although all participants received supplement at school, most did not consume them regularly. Key barriers include dislike of the taste and smell, parental prohibition negative experience consuming iron supplement, and the belief that iron supplements increase menstrual blood flow and volume. Enablers include self-awareness of the supplement’s benefits, trust in school-provided supplements, and positive support from parents and peers. Behavior change strategies are needed to address these barriers and strengthen supporting factors to improve iron supplementation consumption.

Antarctic krill protein-iron complex and peptide-iron complex were obtained to investigate their iron bioavailability, expression of iron-regulated genes, and in vivo antioxidant capacity. Results indicated that Antarctic krill peptide-iron complex increased significantly the hemoglobin (Hb), serum iron (SI) and iron content in the liver and spleen in iron-deficiency anemia (IDA) mice (P < 0.05) compared with those of Antarctic krill protein-iron complex. Despite the gene expressions of divalent metal transporter 1(DMT1), transferrin (Tf) and transferrin receptor (TfR) could be better regulated by both Antarctic krill peptide-iron complex and protein-iron complex, the relative iron bioavailability of the Antarctic krill peptide-iron complex group (152.53±21.05%) was significantly higher than that of the protein-iron complex group (112.75±9.60%) (P<0.05). Moreover, Antarctic krill peptide-iron complex could enhance the antioxidant enzyme activities of superoxidase dismutase (SOD) and glutathione peroxidase (GSH-Px), reduce the malondialdehyde (MDA) level in IDA mice compared with the protein-iron complex, reducing the cell damage caused by IDA. Therefore, these results demonstrated that Antarctic krill peptide-iron complex could be used as a highly efficient and multifunctional iron supplement.

In pigs, iron deficiency anemia (IDA) is the most prevalent deficiency disorder during the early postnatal period frequently developing into a critical illness. Meanwhile, in humans, only low-birth-weight infants, including premature infants are especially susceptible to developing IDA. In both human and pig neonates, the initial cause of IDA is low birth iron stores. In piglets this shortage of stored iron results mainly from genetic selection over the past few decades for large litter size and high birth weight. In consequence, pregnant sows cannot provide sufficient amount of iron to the increasing number of developing fetuses. Supplementation with iron is a common practice for the treatment of IDA in piglets. For decades, the preferred procedure for delivering iron supplements during early life stages has been through the intramuscular injection of large amount of iron dextran. However, this relatively simple therapy, which in general, efficiently corrects IDA, may generate toxic effects, and by inducing hepcidin expression, may decrease bioavailability of supplemental iron. New iron supplements are considered now with the aim to combine improvement of hematological status, blunting hepcidin expression, and minimizing toxicity of the administered iron. We propose that iron-deficient piglets constitute a convenient animal model for performing pre-clinical studies with iron supplements.

Polyelectrolyte-drug complexes are interesting alternatives to improve unfavourable drugs properties. Vancomycin (VAN) is an antimicrobial used in the treatment of methicillin-resistant Staphylococcus aureus pulmonary infections in patients with cystic fibrosis. It is generally administered intravenously with high incidence of adverse side effects, which could be reduced by intrapulmonary administration. Currently, there are no commercially available inhalable formulations containing VAN. Thus, the present work focuses on the preparation and characterization of an ionic complex between hyaluronic acid (HA) and VAN with potential use as inhalable formulations. Particulate-solid HA-VAN25 complex by spray drying from an aqueous dispersion was obtained. FTIR spectroscopy and thermal analysis confirmed the ionic interaction between HA and VAN, while an amorphous diffraction pattern by X-ray was observed. The powder density, geometric size and morphology showed a suitable aerosolization and aerodynamic performance of the powder, indicating the capability of reaching the deep lung. An in vitro extended-release profile of VAN from the complex was obtained, exceeding 24 hours. Microbiological assays against methicillin-resistant and -sensitive reference strains of Staphylococcus aureus, showed that VAN preserves its antibacterial efficacy. In conclusion, HA-VAN25 exhibited interesting properties for the development of inhalable formulations with potential efficacy and safety advantages over conventional treatment.

This research has developed a process for producing ZnO thin film from DEZn deposited onto a PET substrate with low-pressure, high-frequency Ar + O2 plasma using a chemical vapor deposition technique. The aim is to study the film production conditions that affect electrical properties, optical properties, and thin film surfaces. This work highlights the use of plasma energy produced from a mixture of gases between Ar + O2. Plasma production is stimulated with an RF power supply to deliver high chemical energy and push ZnO atoms from the cathode inside the reactor onto the substrate through surface chemical reactions. The results showed that increasing the RF power in plasma production affected the chemical reactions on the substrate surface of film formation. The film preparation at RF power 300 W will give the thickest films. The film has a continuous columnar formation, and the surface has a granular structure. This results in the lowest electrical resistivity of 1.8 x 10-4 Ω-cm. In addition, when fabricated into a DSSC device, the device tested the PCE value and showed the highest value at 5.68%. This is due to the very rough surface nature of the ZnO film, which increases the scattering and storage of sunlight, making cells more efficient. Therefore, the benefit of this research is that it will be a highly efficient prototype of thin film production technology using a chemical process that reduces production costs and can be used in the industrial development of solar cells.

Dietary iron assimilation is critical for health and essential to prevent iron deficient states and related comorbidities, such as anemia. The bioavailability of iron is limited, while its absorption and metabolism are tightly controlled to keep body iron stores within a relatively narrow range. Genetic inactivation of the iron hormone hepcidin causes hereditary hemochromatosis, an endocrine disorder of iron overload characterized by chronic hyperabsorption of dietary iron, with deleterious clinical complications if untreated. The impact of high dietary iron intake and elevated body iron stores in the general population is not well understood. Herein, we summarize epidemiological data suggesting that high intake of heme iron, which is abundant in meat products, poses a risk factor for metabolic syndrome pathologies, cardiovascular diseases, and some cancers. We discuss clinical relevance and potential limitations of data from cohort studies, as well as the need to establish causality and elucidate molecular mechanisms.

In eutrophic waters, such as Mikawa Bay, Japan, anoxic bottom water develops in summer. This causes sulfide release into seawater by sulfate reduction in the sediment, leading to environmental problems. The addition of iron to sediments is a method used to improve the sediment environment, which was devised from a natural phenomenon. However, this method has not yet been quantitatively evaluated. In this study, we aim to quantitatively evaluate the suppressive effect of iron on sulfide release. First, we develop a sediment model that focuses on S and Fe. We then attempted to reproduce the observations and experiments on sulfide dynamics using the model. Consequently, the proposed model was able to reproduce field sulfur and Fe dynamics in sediments. Additionally, the model described the characteristics of sulfide release considering the effects of additive iron materials. Finally, we conducted predictive calculations and quantitatively evaluated the effects of adding iron materials to the sediments in terms of sulfur and iron cycles.

Photothermal therapy (PTT) can overcome cancer treatment resistance by enhancing cell membrane permeability, facilitating drug accumulation, and promoting drug release within the tumor tissue. Iron oxide nanoparticles (IONPs) have emerged as effective agents for PTT due to their unique properties and biocompatibility. Approved for the treatment of anemia, as MRI contrast agents, and as magnetic hyperthermia mediators, IONPs also offer excellent light-to-heat conversion and can be manipulated using external magnetic field for targeted accumulation in specific tissues. Optimizing parameters such as laser wavelength, power density, shape, size, iron oxidation state, functionalization, and concentration is crucial for IONPs effectiveness. In addition to PTT, IONPs enhance other cancer treatment modalities. They improve tumor oxygenation enhancing the efficacy of radiotherapy and photodynamic therapy. IONPs can also trigger ferroptosis, a programmed cell death pathway mediated by iron-dependent lipid peroxidation. Their magneto-mechanical effect can exert mechanical force on cancer cells to destroy tumors, minimizing damage to healthy tissues. This review outlines strategies for managing photothermal performance and PTT efficiency with iron oxide nanoparticles, as well as synergies with other cancer therapies.

Laser Powder Bed Fusion (LPBF), as a transformative technology in the field of additive manufacturing, offers unprecedented design flexibility and material efficiency. This review paper delves into the latest advancements in LPBF technology and the various alloys used in the process, including titanium alloys, aluminum alloys, nickel-based superalloys, steel alloys, copper alloys, and high-entropy alloys. For each alloy category, we discuss their specific applications, performance characteristics, and challenges faced in LPBF usage. The paper discusses important technological breakthroughs, including innovations in laser systems, scanning strategies, and in-situ monitoring technologies, which have enhanced the precision and reliability of LPBF.

Additive manufacturing (AM) is today’s buzzword—and not only in commercial production. One of the AM techniques produces 3D objects with complex geometry using a laser beam. The relationship between the morphology of individual powder particles and the printing process has not been adequately documented yet. This article presents a detailed microscopic analysis of virgin and reused powder particles of maraging steel. Metallographic observation was performed using a scanning electron microscope (SEM). Detailed analyses of individual particles were carried out using SEM with a focused ion beam (FIB) milling capability. Analyses of elemental distribution and phase distribution were performed using EDS and EBSD, respectively. The findings have led to a better understanding and prediction of defects in additive-manufactured products.

Two Iron Age settlements, Tuzusai and Taldy Bulak 2 (ca. 500 BCE to 1 CE), located in Southeastern Kazakhstan on the Talgar alluvial fan north of the Tian Shan range, have yielded a small collection of bone, antler/horn, bronze, and stone artifacts with affinity to nomadic art of the first millennium BCE. Both settlements date within the period of late Saka culture. Two pieces have decorative ornamentations with zoomorphic imagery: a small carved fragment of a with carved images of a wing and an ear and a perforated bone disk with the carving of three birds’ heads. The other artifacts include objects associated with Saka weaponry or nomadic economy such as the two antler/horn psalia (cheek pieces) and a bronze amulet. A carnelian bead will also be described as an imported object. These special finds are found on the occupation floors of mud brick houses and pit houses of settlements, not in grave or burial contexts. The objects are placed in stratigraphic sequence in the settlement sites. Then the method for placing these objects within the chronological framework of “animal-style art” is through comparisons with similar objects found throughout Eurasia—a method used in Soviet and Post-Soviet archaeology. The results show that functional and stylistic elements of the six objects indicate that the Talgar settlements were part of a larger world-system of trade and communication along the early Silk Route(s).

The production of a ton of steel in an integrated steel plant generates of approximately 1 ton of ferrous slag. A great part of ferrous slags is recycled in civil and road construction etc., but a huge amount is still dumped. Recycling ferrous slag as cement precursor was considered the upcycling route. Regulation (EU) 2024/1252 requires the Member States to provide information, until November 2026, on the critical raw materials (CRM) amount in their secondary resources and on quantification methods used for. This study addresses two synergic objectives: ensuring the reliability of XRFS results and screening for CRM in ferrous slags based on XRFS outcomes. The main novelty of the paper is the way of ensuring the reliability of the XRFS results based on weighted arithmetic mean and on the maximum likelihood approach. Secondly, the XRFS measurements carried on ferrous slags demonstrate that they contain significant amounts of CRM like Ba, Sr, Y, etc. XRFS cannot detect light CRM. Our preliminary LIBS measurements on ferrous slags disclosed the presence of Li and Be. The drawbacks of the XRFS technique impose further research to develop an integrated XRFS, LIBS and XRD procedure for comprehensive and trustworthy CRM screening in extractive waste piles.

The characteristics of powders on a bulk scale are heavily influenced by both the material properties and the size of their primary particles. Throughout the stages of storage and transportation in the powder processing industry, various forms of deformation and stress, such as pressure and shear, impact these materials. Recognizing the point at which a powder undergoes yielding becomes particularly significant in numerous applications. There are also times when you need to understand the level of stress needed to maintain it. Measurement of powder yield and flow properties remains a challenge and is addressed in this study. As part of the CALIPER collaborative project, a number of shear experiments were performed using two shearing devices: Schulze ring shearing device and Anton Paar Powder Cell (APCC). These experiments have three purposes: i) Test reproducibility/consistency between two shear devices and test protocols. ii) To relate bulk behavior to microscopic particle properties, focusing on bulk density and thus the effect of cohesion between particles; iii) Investigate the influence of the temperature of heated powders on the powder flow properties, which is important for the industrial reactors. Interestingly, for samples with small particle size, bulk cohesion increases slightly, but bulk friction increases significantly, because of particle interaction effects. The experimental data not only provide useful insight into the role of microscopically attractive van der Waals gravitational and/or compressive forces on the macroscopic flow behavior of bulk powders, but also have industrial relevance. We also provide a robust datas of cohesive and attritional fine powder for silo design used for calibration and validation of silos, models and computer simulations.

A critical challenge underpinning the adoption of Additive Manufacture (AM) as a technology is the postprocessing of manufactured components. For Selective Laser Sintering (SLS) this can involve the removal of powder from the interior of the component, often by vibrating the component to fluidise the powder to encourage drainage. In this paper we develop and validate a computational model of the flow of metal powder suitable for predicting powder removal from such AM components. The model is a continuum Eulerian multiphase model of the powder including models for the granular temperature; the effect of vibration can be included through appropriate wall boundaries for this granular temperature. We validate the individual sub-models appropriate for AM metal powders by comparison with in-house and literature experimental results, and then apply the full model to a more complex geometry typical of an AM Heat Exchanger. The model is shown to provide valuable and accurate results at a fraction of the computational cost of a particle-based model.

The application of solvent method in the preparation of polypropylene powders was investigated, including the influence of various technological conditions, such as the raw material melt index of polypropylene, processing temperature, dosage of the solvent and the packing pressure. The experimental data show that using solvent method can effectively produce polypropylene powder, and the optimal technological conditions are: melt index of polypropylene being about 17.8 g/10min, processing temperature being about 166.0 ℃, dosage of the solvent being about 0.067g/ml and the packing pressure being about 0.7MPa.Under this technological conditions, polypropylene powder with excellent sphericity could be prepared, the apparent density of powder can reach 0.40 g/cm3 and the prepared powder displayed a narrow size distribution with the mean size of about 42.7 µm.

Pathogenic microorganisms can cause a range of infectious diseases and are often treated with antimicrobial agents. The rise of antimicrobial resistance caused by inappropriate use of these agents in various settings has become a global health threat. There is, therefore, a need to find new and effective agents to combat infections caused by resistant pathogens. Nanotechnology has seen significant growth and development in recent years and has a wide range of applications in various fields, including health, agriculture, and industry. This novel area offers the potential for the synthesis of nanoparticles (NPs) with antimicrobial activity, such as iron oxide nanoparticles (IONPs). The use of IONPs is a promising way to overcome antimicrobial resistance or pathogenicity because of their ability to interact with several biological molecules and to inhibit microbial growth. This review focuses on the most common green synthesis methods for producing IONPs using bacteria, fungi, plants, and organic waste, as well as the most common methods for the characterization of these IONPs. Finally, it summarizes their application as promising antibacterial, antifungal, antiparasitic, and antiviral agents.

Iron deficiency (ID) is by far the most common nutritional disorder in developing and developed countries. When left untreated, ID leads to anemia. Although the usual recommended treatment for iron deficiency anemia (IDA) is oral iron therapy with countless products, such therapy necessitates administration for &gt;3-6 months with questionable patient compliance since most oral iron products have an unpleasant metallic aftertaste and cause intestinal side effects. In addition, in certain gastrointestinal conditions, such as inflammatory bowel diseases or untreated gluten-sensitive enteropathy, oral iron therapy is contraindicated or unsuccessful. Intravenous iron is considered safe in adults, where adverse events are mild and easily managed. The experience with parenteral iron in children is much more limited and many pediatricians appear reluctant to use it because of uncorroborated fears of serious anaphylactic reactions. In the current article, we thoroughly review the available pediatric literature on the use of all commercially available parenteral iron products except ferumoxytol, which was recently removed from the market. We conclude that parenteral iron appears to be safe in children, it works faster than oral iron and the newer third-generation products allow replacement of the total iron deficit at a single setting.

The current study emphasizes on optimizing a suitable ratio of enzymatically hydrolyzed potato powder (EHPP) and whole milk powder (WMP) to produce a quality yogurt by evaluating the physicochemical and rheological properties. The results showed that the addition of EHPP decreased the pH towards acidic conditions which resulted in the high acidity of yoghurt. The proximate composition showed that EHPP increased the ash, protein, water holding capacity (WHC) while fat, synersis, color parameters and total solid were decreased when compared to control yoghurt (CY) sample. Moreover, texture profile (TPA) analysis showed that the addition of EHPP decreased the hardness and cohesiveness while springiness did not show significant difference. Furthermore, rheological properties revealed that EHPP decreased the storage modulus (G’) and loss modulus (G”) when compared with control. In addition to this, sensory analysis revealed that the treatment P4M (1:3) was found as optimum ratio regarding taste, flavor, and aroma. Besides this, scanning electron microscopy (SEM) confirms that the high amount of EHPP resulted in the void holes while CY showed dense gel structure. The prepared yogurt with EHPP provides an excellent flavor, satisfying sweetness and homogeneous texture. These findings suggest the optimum formulation ratio of prepared yogurt was found to be P4M (1:3) for desirable attributes and consumer acceptance. The prepared yogurt from the EHPP presents the potential industrial applications.

The purpose of this work was analysing the compaction of a cohesive material using different DEM simulators to determine the equivalent contact models and identify how some parameters of the simulations affect the compaction results (maximum force and compacts appearance) and computational costs. For that purpose, three cohesion contact models were tested (‘linear cohesion’ in EDEM; ‘SJKR’ and ‘SJKR2’ in LIGGGHTS). The influence of the particle size distribution (PSD) on the results was also investigated. Further assessments were performed on the effect of selecting different timesteps, using distinct conversion tolerances for exporting the 3D models to STL files and moving the punch with different speeds. Consequently, it was possible to determine that a timestep equal to a 10% Rayleigh timestep, a conversion tolerance of 0.01 mm and a punch speed of 0.2 m/s are adequate for simulating the compaction process using the contact models in this work. In addition, the results determined that the maximum force was influenced by the PSD because of the rearrangement of the particles. The PSD was also related to the computational cost because of the number of simulated particles and their sizes. Finally, an equivalence was found between the linear cohesion and SJKR2 contact models

Oral ferric citrate hydrate (FCH) is effective for iron deficiency in hemodialysis patients.; however, it remains unclear how iron balance in the body affects iron absorption from the intestinal tract. This prospective, observational study (Riona-Oral Iron Absorption Trial, R-OIAT, UMIN 000031406), conducted at 42 hemodialysis centers in Japan, wherein 268 hemodialysis patients without inflammation were enrolled and treated with a fixed amount of FCH for 6 months. We assessed the predictive value of hepcidin-25 for iron absorption and iron shift between ferritin (FTN) and red blood cells (RBCs) following FCH therapy. Serum iron changes at 2 h (ΔFe2h) after FCH ingestion were evaluated as iron absorption. The primary outcome was the quantitative delineation of iron variables on ΔFe2h and the secondary outcome was the description of the predictors of body iron balance. Generalized estimating equations (GEE) were used to identify the determinants of iron absorption during each phase of FCH treatment. ΔFe2h increased when hepcidin-25 and MCH decreased (-0.155, -0.242 to -0.068, p = 0.001; -2.574, -4.421 to -0.726, p = 0.006, respectively) in GEE. Hepcidin-25 increased when erythropoiesis-stimulating agent (ESA) decreased (-0.002, -0.002 to -0.001, p=0.000). FTN increased when RBC and ESA decreased (-0.466, -0.605 to -0.327, p=0.000; -0.002, -0.004 to -0.000, p=0.05, respectively. Limiting erythropoiesis to maintain hemoglobin levels induces RBC reduction in hemodialysis patients, resulting in increased hepcidin-25 and FTN levels. Hepcidin-25 production may prompt an iron shift from RBC-iron to FTN-iron, inhibiting iron absorption even with continued FCH intake.

The global steel industry is a major contributor to greenhouse gas emissions, and the adoption of green hydrogen in Direct Reduced Iron (DRI) production has the potential to significantly reduce CO2 emissions and support climate targets. This review explores the environmental, economic, technological, and social implications of using green hydrogen in DRI processes. The findings suggest that green hydrogen can reduce emissions by up to 90% compared to traditional methods, enhance energy security, and stimulate local economic development. However, high initial costs, energy efficiency concerns, and social acceptance issues remain significant barriers. The review also highlights the importance of integrating carbon capture and storage technologies, addressing logistical challenges, and considering the geopolitical implications of a shift towards green hydrogen. Green hydrogen presents a promising solution for decarbonising the steel industry but continued research, investment in infrastructure, and strategic planning are essential to overcome the challenges and drive widespread adoption.

Hereditary hemochromatosis (HH) is the main genetic cause of iron overload and is regarded as metal-related human toxicosis. HH may result from HFE and non-HFE gene mutations causing hepcidin deficiency or hepcidin resistance. The disorder has a high biochemical penetrance, but a low clinical prevalence. Unfortunately, the majority of patients with HH remain undiagnosed at their disease-curable stage. The main aim of HH therapy is to prevent iron overload in the early-phase disease and elimination of excess iron from the body by phlebotomy in its late stage. Raising global awareness of HH among health professionals, their training to pay attention to early HH signs and symptoms, and strict patient monitoring are critical management strategies for preventing treatment delays, upgrading its efficacy, and improving patient prognosis.

Powder Bed Fusion (PBF) is a type of Additive Manufacturing (AM) technology that builds parts in a layer-by-layer fashion out of a bed of metal powder via the selective melting action of a laser or electron beam heat source. The technology has become widespread, however the demand is growing for closed loop process monitoring and control in PBF systems to replace the open loop architectures that exist today. This paper demonstrates the simulated efficacy of applying closed-loop state estimation to the problem of monitoring temperature fields within parts during the PBF build process. A simplified LTI model of PBF thermal physics with the properties of stability, controllability and observability is presented. An Ensemble Kalman Filter is applied to the model. The accuracy of this filters’ predictions are assessed in simulation studies of the temperature evolution of various test parts when subjected to simulated laser heat input. The significant result of this study is that the filter supplied predictions that were about 2.5x more accurate than the open loop model in these simulation studies.

Cellular substructure has been widely observed in the sample fabricated by laser powder bed fusion, while its growth direction and the crystallographic orientation have seldom been studied. This research tries to build a general model to construct the substructure from its two-dimensional morphology. All the three Bunge Euler angles to specify a unique growth direction are determined, and the crystallographic orientation corresponding to the growth direction is also obtained. Based on the crystallographic orientation, the substructure in the single track of austenitic stainless steel 316L is distinguished between the cell-like dendrite and the cell. It is found that, with the increase of scanning velocity, the substructure transits from cell-like dendrite to cell. When the power is 200 W, the critical growth rate of the transition in the single track can be around 0.31 ms^-1.

Mn-promoted bulk iron catalysts with high specific surface area (82-211 m2.g-1) were synthesized by coprecipitation followed by drying under supercritical conditions. The catalysts were tested in the CO2 hydrogenation reaction. The Mn-promoted iron catalysts showed better textural properties than the bare Fe2O3 catalyst, allowing better dispersion of the active phase, easier reduction of iron oxide, better carburization of iron oxides and higher catalytic activity than the bare Fe2O3 catalyst. The best activity results were obtained by catalyst promotion with a very low amount of Mn (Mn/Fe ratio of 0.05). Upon steady-state conditions (T=340 ºC, total pressure of 20 bar and H2/CO2=3), this catalyst showed high CO2 conversion (44.2%) and selectivity to C2-C4 hydrocarbons (68%, olefin to paraffin ratio of 0.54), while the selectivity to C5+ hydrocarbons, CH4 and CO was about 3.2, 38.5 and 5%, respectively. A close correlation was found between catalyst textural properties and CO2 conversion. The most active MnFe-0.05 catalyst shows high stability during 72 h of reaction related to low amount of soft coke formation and catalyst activation through the formation of χ-Fe5C2 phase during the on-stream reaction.

Ghrelin and obestatin, two antagonist peptide hormones, are purportedly involved in stimulating appetite and controlling energy balance in humans. Serum ghrelin level is also associated with iron deficiency anemia (IDA), but no study has yet been made of the obestatin level in patients with IDA, even though both hormones are a single gene product. Therefore, the purpose of this investigation is to see whether there is a link between IDA and these two hormones among other hematological parameters in patients with IDA. To measure ghrelin and obestatin, human saliva and serum were collected from 30 women with IDA, aged 31.7 ± 10.7 years, and 30 control women, aged 30.2 ± 8.0 years, with repeated collection of samples over a period of 1 week and 1 month. Saliva and serum ghrelin levels were measured by ELISA. Serum hemoglobin, ferritin, hematocrit and total iron-binding capacity (TIBC) values were determined with an Olympus AU2700. Saliva and serum ghrelin and obestatin levels were significantly lower in the IDA group compared with controls; these levels increased slightly above baseline with iron treatment, but remained below the control values. Furthermore, and as expected, serum hemoglobin, ferritin, and hematocrit levels were significantly increased with iron treatment, while total iron-binding capacity decreased compared to baseline concentrations. The findings suggest that IDA might be linked to imbalance of circulating (serum) and non-circulating (saliva) ghrelin and obestatin levels. Decreased ghrelin and obestatin might destroy iron homeostasis through its effect on intestinal absorption. Measuring these hormone levels might be useful for monitoring the response to iron treatment. Also, serum and saliva levels for both hormones were well correlated. Thus, using saliva in place of serum for monitoring the two hormones should minimize inconvenience and patient discomfort.

Recent advancements in nanotechnology have led to the development of multifunctional iron oxide nanoparticles, presenting new opportunities in cancer therapy. This study aimed to synthesize and evaluate citric acid-coated/ folic acid conjugated nanoparticles loaded with doxorubi-cin and investigate their efficacy in experimental tumor models. For synthesis, controlled co-precipitation method was employed to produce highly dispersive, multifunctional nanofluids with a narrow size distribution of iron oxide nanoparticles. Nanoparticles were characterized using Dynamic Light Scattering (DLS) and Electrophoretic Light Scattering (ELS) for size distribution and zeta potential, X-ray Diffraction (XRD) and Transmission Electron Microscopy (TEM) for structure and morphology, Vibrating Sample Magnetometry (VSM) for magnetic properties, and UV-Visible (UV-Vis) and Fourier-Transform Infra-red (FTIR) spectroscopy for modification confirmation. In vitro experiments employed RM1 (prostate cancer) and MEC1 (Chronic lymphocytic leukemia) cell lines to assess cytotoxicity and drug delivery efficiency. Fluorescence microscopy confirmed the intracellular delivery of doxorubicin by these nanoparticles, highlighting their potential for targeted therapy. As a result, nanoparticles conjugated with folic acid showed reduced efficacy over time. This study underscores the critical role of nanoparticle modifications in optimizing therapeutic outcomes. Future research should focus on further refining nanoparticle formulations and long-term effects in vivo, for development of effective and safe agents for targeted cancer treatment.

Inflammation is an underlying problem for many disease states and has been implicated in iron deficiency (ID). This study aimed to determine whether iron status is improved by epigallocate-chin-3-gallate (EGCG) through reducing inflammation. Thirty-two male Sprague-Dawley rats were randomly divided into four groups (n = 8 each): positive controls, negative controls, lipo-polysaccharide (LPS, 0.5 mg/kg body weight), and LPS + EGCG (LPS plus 600 mg EGCG/kg diet). Iron status, hepcidin, C - reactive protein (CRP), serum amyloid A (SAA), and interleukin-6 (IL-6) were measured. There were no differences in treatment groups compared with control in CRP, hepcidin, and liver iron concentrations. Serum iron concentrations were significantly lower in the LPS (p=0.02) and the LPS+EGCG (p=0.01) than in the positive control group. Compared to the positive control group, spleen iron concentrations were significantly lower in the negative con-trol (p<0.001) but not with both LPS groups. SAA concentrations were significantly lower in LPS + EGCG group compared to LPS alone group. IL-6 concentrations were significantly higher in LPS+EGCG (p= 0.004) than in any of the three groups. EGCG reduced SAA concentrations but did not affect hepcidin or improve serum iron concentration or other iron markers.

We present a simple strategy to generate a family of carbon dot/iron oxide nanoparticles (C/Fe-NPs) that relies on the thermal decomposition of iron (III) acetylacetonate in the presence of a highly fluorescent carbon-rich precursor, while polyethylene glycol serves as the passivation agent. By varying the molar ratio of the reactants, a series of C/Fe-NPs have been synthesized with tuneable elemental composition in terms of C, H, O, N, Fe. The quantum yield is enhanced from 6% to 9% as the carbon content increases from 27% to 36%, while the room temperature saturation magnetization is improved from 4.1 emu/g to 17.7 emu/g as the iron content is enriched from 17 to 31%. In addition, the C/Fe-NPs show excellent antimicrobial properties, minimal cytotoxicity and demonstrate promising bioimaging capabilities, thus showing great potential for the development of advanced diagnostic tools.

Two billion people worldwide suffer from anemia with reproductive-age women being disproportionately affected. Iron plays a crucial role in cellular function and impacts cognition, physical function, and quality of life. Iron deficiency (ID) and iron deficiency anemia (IDA) are associated with adverse effects on pregnancy and fetal development. Oral iron supplementation has been the standard treatment for IDA for decades often producing sub-optimal outcomes. Many babies are still being born with ID and suffer adverse sequelae due to inadequate iron levels in the mothers. Is it time to consider broad scale-up of parenteral iron as a new standard of care?

Formula feeding, as an alternative to breastfeeding, offers benefits such as convenience and consistent nutrition. Among the drawbacks of formula feeding, however, is potential dilution or concentration errors in the of formula during preparation that may lead to infant health issues. The present study aimed to investigate the accuracy of caregiver measurements as they prepared infant formula under multiple conditions, compared with manufacturer specifications. A diverse sample of caregivers (N = 84) participated in this cross-over experimental study. Participants hand-scooped infant formula powder and poured water to prepare 4oz and 7oz feedings, using both a standardized set of infant formula products and participants’ own products. Linear mixed effects models were used to estimate fixed effects of target amount (4oz versus 7oz) and products (participant versus researcher) on mean absolute percent error (MAPE) of measurement. Across all conditions MAPE was significantly greater for measuring powder than for water (9.0% vs. 4.4%; p&lt;0.001) with a combined powder and water MAPE at 13.0%. Greater measurement error was associated with the odd-sized 7oz preparation and participants’ own products. We observed considerable variability and substantial error during infant formula preparation, particularly for hand-scooping of powder, which tended toward higher values than the theoretical gold standard.

Molybdenum tailings powder (MTs) is an industrial waste that contains more than 85% contents of SiO2, Al2O3, CaO, and Fe2O3. Therefore, MTs has the potential pozzolanic activity and can be used as a mineral admixture in cementitious materials. In order to understand the influence of MTs as an admixture on the cement hydration process, the hydration heat and hydration kinetics of the composite cementitious materials (CCMs) were investigated by an isothermal calorimeter and the Krstulovic-Dabic model. Furthermore, the influences of fly ash (FA), slag (SL) and MTs on hydration heat at the same content were compared and analyzed. Results show that proper amount of MTs can promote the hydration of CCMs. When the content of MTs is not more than 15%, the second exothermic peak of CCMs appears earlier and the peak heat release increases. However, when the content of MTs exceeds 15%, the second exothermic peak of CCMs is delayed and the peak heat release decreases. The cumulative heat release of CCMs gradually decreases with an increasing content of MTs. When the replacement of MTs, FA, and SL is 15% respectively, the addition of MTs enhances the second exothermic peak of CCMs compared to FA and SL. The final heat release of MTs is higher than that of FA, but lower than that of SL. The hydration process of CCMs undergoes three stages: nucleation and crystal growth (NG), interactions at phase boundaries (I), and diffusion (D). The incorporation of MTs shortens the NG stage and I stage.

Powder bed fusion (PBF) process is a metal additive manufacturing process which can build parts with any complexity from a wide range of metallic materials. PBF process research has predominantly focused on the impact of only a few parameters on product properties due to the lack of a systematic approach for optimizing a large set of process parameters simultaneously. The pivotal challenges regarding this process require a quantitative approach for mapping the material properties and process parameters onto the ultimate quality; this will then enable the optimization of those parameters. In this study, we propose a two-phase framework for optimizing the process parameters and developing a predictive model for 316L stainless steel material. We also discuss the correlation between process parameters -- i.e., laser specifications -- and mechanical properties and how to achieve parts with high density (> 98%) as well as better ultimate mechanical properties. In this paper, we introduce and test an innovative approach for developing AM predictive models, with a relatively low error percentage of 10.236% that are used to optimize process parameters in accordance with user or manufacturer requirements. These models use support vector regression, random forest regression, and neural network techniques. It is shown that the intelligent selection of process parameters using these models can achieve an optimized density of up to 99.31% with uniform microstructure, which improves hardness, impact strength, and other mechanical properties.

Traditionally Moringa is known as mystical miracle tree or the tree of life. Soup can be classified as an appetizer, warm food during cold and sick. Moringa oleifera pods have been procured from College of Agriculture, JNKVV, Jabalpur. The present investigation is planned with objectives to standardize best combination of for the development of instant soup mix, to evaluate various quality parameters, to evaluate the storage stability and cost estimation of product. Protein in instant soup is ranged from 9.76 to 11.89 percent in different formulations of instant soup mix. Formulation MPP4 (11.89) had significantly maximum protein content followed by MPP3, MPP2, MPP1 and Control with the minimum protein content. The original instant soup mix (control) exhibited highest carbohydrate content (61.52%) followed by MPP1, MPP3, MPP4, and MPP2 with lowest content. The evaluated scores of control for colour and appearance, taste, flavour, consistency, after taste and overall acceptability are 8.36, 8.50, 8.60, 8.90, 8.76 and 8.63 respectively

Metal powder bed fusion (PBF) additive manufacturing (AM) builds metal parts layer by layer upon a substrate material. The strength of this interface between substrate and printed material is important to characterize, especially in applications where the substrate is retained and included in the finished part. This paper studied the tensile and torsional strengths of wrought and additively manufactured (through PBF) SS316L and compared them to specimens composed of half wrought material and half PBF material. The PBF specimens consistently exhibited higher strength and lower ductility than the wrought specimens. The hybrid PBF/wrought specimens performed similarly to the wrought material. In no specimens did any failure appear to occur at or near the interface between wrought substrate and PBF material. In addition, most of the deformation in the PBF/wrought specimens appeared to be limited to the wrought portion of the specimens. These results are consistent with microscopy showing smaller grain size in the PBF material, which often leads to increased strength in SS316L due to the Hall-Petch relationship.

The microstructural evolution, thermodynamics and kinetics of Mo-21%Tm₂O₃ (mass fraction, %) powder mixtures during ball milling were investigated using X-ray diffraction and transmission electron microscopy. Ball milling induced Tm₂O₃ to be decomposed and then dissolved into Mo crystal. The supersaturated nanocrystalline solid solution of Mo (Tm, O) was obtained after 96 h of ball milling. The elements of Mo, Tm and O were distributed uniformly in the ball-milled particles. Based on the semi-experimental theory of Miedema, a thermodynamic model was developed to calculate the driving force of phase evolution. There was no chemical driving force to form a crystal solid solution of Tm atoms in Mo crystal or an amorphous phase because the Gibbs free energy for both processes was higher than zero. For Mo-21%Tm₂O₃, it was mechanical work, not negative heat of mixing, that provided the driving force to form supersaturated nanocrystalline Mo (Tm, O) solid solution.

Thalassemia treatment still relies on supportive care, including mainly blood transfusion and iron chelation therapy. Iron chelation therapy is considered the main responsible factor for the marked improvement in survival of thalassemic patients. Hemosiderosis should be prevented with appropriate chelation therapy from early childhood, timely dose adjustment according to changing body weight, as well as close monitoring of organ iron overload. Three iron chelators are currently available and the choice of appropriate chelator or their combination in pediatric population is individualized, depending on iron overload in target organs, patient age, adverse events and compliance issues, due to the limitations in their administration.

Iron (Fe) deficiency specifically is the most common nutritional disorder due to insufficient absorbable Fe. Biofortification is a process of enriching the nutrient content of staple crops and is considered as a sustainable and cost-effective strategy to address micronutrient deficiency problems especially in the less developed countries. Chickpea (Cicer arietinum L.) is a staple food in many developing countries worldwide and is an excellent source of micronutrients. Biofortification of chickpea is a possible solution to address Fe deficiency problem. Chickpea biofortification experiment was conducted under field conditions to evaluate the effects of different doses of Fe fertilizer (0 kg ha-1,10 kg ha-1 and 30 kg ha-1 of Fe-EDDHA) on Fe content in seeds of 18 chickpea cultivars. The experiment was designed as a factorial combination of 18 chickpea cultivars and 3 different doses in a randomized complete block design with 4 replications at two locations in Saskatchewan in 2015 and 2016. Fe concentration in seeds across 18 different chickpea cultivars increased with Fe fertilization. Fe concentration in X05TH20-2 and CDC Frontier cultivars increased from 57 ppm to 59 ppm and 56 ppm to 58 ppm, respectively, after adding Fe fertilizer in both location in 2015 and 2016.

This paper investigates the effect of Fe contamination on the microstructure and mechanical properties of Al-7Si-0.7Mg-Fe2.5 alloy processed by Laser Powder Bed Fusion (LPBF) and heat treated in two different conditions: (1) Solution Heat Treatment (SHT) at 520 °C, followed by artificial ageing at 160 °C (T6), and (2) Direct Artificial Ageing of the as-printed material at 160 °C (DAA). Microstructural characterization was carried out by Optical Microscopy (OM), X-Ray Diffraction (XRD), Scanning Electron Microscopy (SEM), and Transmission Electron Microscope (TEM). Mechanical characterization was carried out by tensile tests at room temperature. The formation of fine AlSiFe phases such as α-AlFeSi, β-AlFeSi, and π-Al8Si6Mg3Fe had no deleterious effect on the mechanical properties compared to previous studies for AlSIMg alloys without Fe. However, compared to the as-printed condition, the T6 heat treatment decreased the ultimate tensile strain significantly, while the elongation to the fracture presented a slight improvement.

This work deals with the analysis of phase composition of sintered Ti-Al-C composite materials under high voltage electrical discharge. The samples of Ti-Al-C powder composites were tested by SEM, Raman spectroscopy and XRD. It was determined that the treatment of the powder by high voltage electrical discharge (HVED) and further sintering at high temperatures using the method of spark plasma sintering (SPS) encourages the formation of the intermetallic reinforcing phases, carbides and different nanocarbon structures like graphene and fullerenes, as well as pure graphite. Intermetallic phases and nanocarbon structures improve mechanical and physical properties of the composites. By using experimental methods mentioned above, the phase composition of Ti-Al-C powder composites obtained at different sintering temperatures was determined.

Rapid and accurate prediction of residual stress in metal additive manufacturing processes is of great importance to guarantee the quality of the fabricated part to be used in a mission-critical application in the aerospace and automotive industries. Experimentation and numerical modeling are valuable tools for measuring and predicting the residual stress; however, to-date conducting experimentation and numerical modeling is expensive and time-consuming. Thus, herein, a physics-based thermomechanical analytical model is proposed to predict the residual stress of the additively manufactured part rapidly and accurately. A moving point heat source approach is used to predict the temperature field by considering the effects of scan strategies, heat loss, and energy needed for solid-state phase transformation. Due to the high temperature gradient in this process, part experiences a high amount of thermal stress following solidification which may exceed the yield strength of the material. The thermal stress is obtained using Green’s function of stresses due to the point body load. The Johnson-Cook flow stress model is used to predict the yield surface of the part under repeated heating and cooling. As a result of the cyclic heating and cooling and the fact that the material is yielded, the residual stress build-up is predicted based on incremental plasticity and kinematic hardening behavior of the metal according to the property of volume invariance in plastic deformation in coupling with the equilibrium and compatibility conditions. The computational methodology is realized with the laser powder fusion of maraging steel 350 as a material of example. The validation of the predictive models has been presented in terms of the comparison of predicted and measured scan-direction and build-direction residual stress distributions along depth of build under various process parameter combinations. Moreover, for the first time, the Jonson-Cook parameters of maraging steel 350 are predicted using analytical modeling of machining forces and non-linear optimization techniques.

This study used eco-friendly materials known as Periwinkle Shell Powder (PSP) in stabilizing the engineering properties of lateritic soil. Preliminary test was performed on the un-stabilized lateritic soil for the purposes of identification and classification (natural moisture content, liquid limits, plastic limits, and plasticity index). The engineering tests were conducted on the lateritic soil stabilized with additions of (2, 4, 6, 8 and 10 %) PSP and OPC respectively. The result showed that cement gave a progressive increase in the Maximum Dry Density (MDD) of the lateritic soil from 1875 kg/m3 (2 %) to 2294 kg/m3 (10 %) respectively. This represents 22 % increase in the MDD from the un-stabilized state. For PSP, the Maximum MDD was attained at 6 % (1974 kg/m3), representing 5.3 % increase in MDD of the soil from the un-stabilized state. For both stabilizing agent, the Optimum Moisture Content (OMC) increases from 13.65 % to 13.83 % and from 11.72 % to 14.41 % for Cement and Periwinkle Shell Powder respectively. PSP recorded an increase of 5.6 % of CBR value compared with OPC that recorded an increase of 34 % CBR value. The study therefore concluded that Periwinkle Shell Powder (PSP) could be considered as good stabilizer for clayey or lateritic, and its uses as a stabilizer could also provide a big relief to the environmental pollution caused by its indiscriminate dumping.