MIMO (multiple-input multiple-output) radar provides much more flexibility than the traditional radar for its ability to realize far more observation channels than the actual number of T/R (transmit and receive) elements. Designing the array of MIMO imaging radar, the commonly used virtual array theory generally assumes that all elements are placed on the same line. However, due to the physical size of the antennas and coupling effect between T/R elements, a certain height difference between T/R arrays is essential, resulting in the defocusing of edge points of the scene. On the other hand, the virtual array theory implies far-field approximation, leading to inevitable high grating lobes in the imaging result of near-field edge points of the scene observed by common MIMO array. To tackle these problems, this paper derives the relationship between target’s PSF (point spread function) and pattern of T/R arrays, by which the design criterion of near-field imaging MIMO array is presented. Firstly, the proper height between T/R arrays is designed to focus the near-field edge points well. Secondly, the far-field array is modified to suppress the grating lobes in the near-field area. Finally, the validity of the proposed methods is verified by simulations and an experiment.

The commercial oxygen-free copper sheets were cold-rolled with reduction rates ranging from 20% to 87% reduction rate and annealed at 400, 500 and 600 °C. The microstructure and texture evolution during cold-rolling and annealing processes were studied using optical microscopy (OM), the scanning electron microscopy (SEM) and the electron back-scattered diffraction (EBSD). The results show that the deformation textures of {123} (S) , {112} (Copper) and {110} (Brass) were continuously enhanced with the increase of cold-rolling reduction. The orientations along the α-oriented fiber converged towards Brass and the orientation density of β fiber obviously increased when the rolling reduction exceeded 60%. The recrystallization texture was significantly affected by the cold-rolling reduction. After 60% cold-rolling reduction, Copper and S textures components gradually decreased and {011} recrystallization texture component formed with the increase of annealing temperature. After 87% cold-rolling reduction, a strong Cube texture formed and other textures were inhibited with the increase of annealing temperature. The strong Brass and S deformation texture was conducive to the formation of a strong Cube annealing texture. The density of annealing twin boundary decreased with the increase of annealing temperature, and more annealing twin boundaries formed in the oxygen-free copper sheets with the increase of cold rolling reduction.

The relaxation process of lithium batteries caused by load variation is considered. It is shown that such processes have strong dependence on internal physical and chemical processes and battery technical conditions. Theoretical expressions of the relaxation process caused by a step-like load variation have been obtained for 1^st and 2^nd order equivalent electrical circuits. The experimental investigations show that the obtained models fit the real relaxation processes and the behavior of the identified parameters could be explained by specific features of physical and chemical processes within the lithium battery. It should be noted that the obtained results can be generalized for a different type of electrochemical power source. The proposed approach makes it possible to provide means for electrochemical power source characterization and diagnostic, the main advantages of which are good time localization of measurement procedures and inexpensive apparatus implementation.

Effects and interactions of incubation time and chick preplacement holding time on mortality at placement, utilization of yolk sac, crop filling rate, early feeding–drinking behavior and broiler live performance were investigated. Ross 308 broiler hatching eggs from a 39-week-old flock were set in two identical setters in a commercial hatchery,with setting time 12 hours earlier in one machine. At the end of incubation, chicks were removed from the hatchers at the same time. Thus, incubation times were either 504 h (normal incubation time (NIT) treatment) or 516 h (longer incubation time (LIT) treatment). After pull time, chicks from each incubation time group were subjected to either 6, 24, 48, 60 or 72 h preplacement holding times. At placement, chicks were given access to feed and water. In total, 19,200 chicks were randomly assigned to a total of 10 subtreatment groups (2 incubation times × 5 preplacement holding times). Therefore, a total of 1,920 chicks were used in each subtreatment group for the grow-out period in a commercial broiler house. An interaction was found between incubation time and preplacement holding time for residual yolk sac (RYS) weight (g, %) (p < 0.001). RYS weight was greater at pull time and at 6 and 24 h of preplacement holding time in the NIT treatment compared to the LIT treatment, while differences were no longer evident at 48–72 h. The lowest percentage of chicks with full crops and eating activity was observed in the shortest preplacement holding time (6 h) group at 3 h after placement. As expected, the initial BW at placement clearly decreased with increasing duration after the pull time (p < 0.05) with the highest and lowest weights were found in the 6 and 72 h holding time treatments respectively. This BW difference was still evident at 35 d after placement and chicks held for the longest period after the pull time (72 h) showed the lowest BW (p < 0.001). However, there was no significant difference between the 6 and 60 h preplacement holding times. Mortality during the first 7 d after placement increased only when the preplacement holding time was extended to 72 h (p = 0.031). Similar to the 7 d results, chicks held for 72 h exhibited higher 0-35 day mortality compared to those held for 6 or 24 h (p = 0.028). Neither BW nor mortality was affected by incubation time treatment at 35 d after placement (p > 0.05). It can be concluded that there were no significant differences in average BW and mortality, up to and including a 60-h holding time under thermal comfort conditions, but a 72-h preplacement holding time resulted in final BW and mortality being negatively affected. In addition, LIT tended to have a beneficial effect on BW and mortality compared to NIT when the preplacement holding time was shorter (6–24 h) but had a negative effect for extended holding times (48–72 h).

This study aims to spatially analyze the distribution characteristics of vacant homes in Asan-si, Chungcheongnam-do, and understand the differences in factors causing vacant homes by type. We use a variety of statistical methods to examine these factors and identify key influencing factors such as the number of vacant stores, changes in overall population, land use complexity, and physical characteristics of land and buildings. The findings reveal that the factors contributing to the occurrence of vacant homes vary significantly by region and property type, highlighting the need for region-specific policies. For instance, in old town areas, small lot ratios and land use complexity are significant, while in rural village, the average number of floors and land use complexity play a major role. This study underscores the diversity of factors influencing vacant homes, suggesting that policies should be tailored to the unique characteristics of different regions to effectively address this issue.

In this paper, a mathematical and physical interpretation of the length and the angle of the catenary curve made by the anchor chains was implemented, and the safety of an anchored vessel was reviewed. So far, holding force has been calculated approximately when the angle of the catenary curve of the anchor chain to the seafloor is 0°. In this study, the holding force equation was strictly derived for the case of anchor dragging. In addition, the equations for the angle and length of the catenary curve were mathematically derived when the anchor dragging occurs. The holding force equation derived in this paper are expected to help provide guidelines in vessel design or increase the safety of anchoring.

Cash holding is important for Chinese manufacturing firms coping with the increasing cost of financing and stiff market conditions. This study examines the impact of cash holding on the firm value of Chinese manufacturing firms. We find evidence that a non-linear relationship exists between cash holding and firm value in manufacturing firms of China. The study reveals that financially constrained firms having a higher level of cash holding negatively affects the firm value, while the unconstrained firms having a lower level of cash holding positively influences the firm value. Finally, this research is enriched by adopting the novel measure of managerial op-timism and reveals the interactive role of cash holding and optimism on firm value. The study concludes that managerial optimism influences the firm’s cash holding decisions and this is more costly for unconstrained firms.

We consider the financial planning problem of a retiree wishing to enter a retirement village at a future uncertain date. The date of entry is determined by the retiree's utility and bequest maximisation problem within the context of uncertain future health states. In addition, the retiree must choose optimal consumption, investment, bequest and purchase of insurance products prior to her full annuitisation on entry to the retirement village. A hyperbolic absolute risk-aversion (HARA) utility function is used to allow necessary consumption for basic living and medical costs. The retirement village will typically require an initial deposit upon entry. This threshold wealth requirement leads to exercising the replication of an American put option at the uncertain stopping time. From our numerical results, active insurance and annuity markets are shown to be a critical aspect in retirement planning.

The research probes the relationship between the Minimum Support Price (MSP) price and its income impact on the farmers with different agricultural land-holdings. It examines maize crop cultivation income under three conditions if a farmer is getting crop production value at MSP, above 20% of MSP and above 40% of MSP. It then evaluates the farmers belonging to marginal, small, semi-medium, medium and large categories position in terms of poverty criteria suggested by the World bank. For analysis purposes, it uses an economic-model approach and suggest the concept of survival income for agricultural farmers. Its findings prove that marginal and small farmers require benefits beyond the MSP rate to push them above the poverty line.

Sharding shows great potential for extending the blockchain. The current challenge facing sharded blockchain technology lies in addressing the extended transaction confirmation times caused by isolated states between shards and unbalanced transaction allocation strategies. These factors contribute to an increase in cross-shard transactions and disproportionate shard workload, ultimately resulting in indefinite confirmation delays for cross-shard transactions. A critical priority for sharded blockchain systems is to conduct a comprehensive qualitative analysis to better understand and mitigate the prolonged transaction confirmation times. We introduce a Product-Form Queue Network (PFQN) model to address the transaction confirmation time problem in sharded blockchains and incorporate a new confirmation queue to more accurately simulate the actual transaction confirmation process in the blockchain. In addition, we provide a detailed quantitative analysis of the relationship between network load, consensus efficiency, and security in sharded blockchains, laying a theoretical foundation for achieving robustness and efficiency in sharded blockchains. This research not only contributes to addressing the scalability issues in sharded blockchains but also offers a new perspective for future research directions.

The necessity for precise and current data concerning the dynamics of land cover change in Indonesia is crucial for efforts to reduce natural vegetation cover due to agricultural expansion. The functionality of monitoring systems that incorporate Terra-MODIS is currently compromised by the limited availability of data for the immediate future. This study seeks to assess the potential of VIIRS satellite imagery in developing an early warning system for monitoring vegetation cover change in Indonesia. The Normalized Differential Open Area Index (NDOAI) computed from the 8-day’ VIIRS data was employed to detect changes in vegetation cover based on pixel-by-pixel subtraction in the NDOAI data time series. Evaluating the pixel-level accuracy of change detection is complicated due to the fact that we evaluate a change map at a coarser resolution than the Landsat-based reference map. The results revealed that increasing the threshold percentage is associated with improved accuracy. In change detection, there is often a trade-off between accuracy and sensitivity. A threshold that is too low may result in false positives, while a threshold that is too high may lead to missed changes. This study demonstrates that when a threshold value of less than 20% is applied, Landsat can identify vegetation cover changes at an earlier stage. Conversely, when a threshold value greater than 20% is employed, VIIRS will detect the change 4.5 days earlier than Landsat. Additionally, VIIRS is capable of detecting changes 25.4 days and 54.8 days faster than Landsat, respectively, when using thresholds of 40% and 75%.

Chiral interactions play a crucial role in both chemistry and biology. Understanding the behavior of chiral molecules and their interactions with other molecules is essential, and chiral interactions in solutions are particularly important for studying chiral compounds. Chirality influences the physical and chemical properties of molecules, including solubility, reactivity, and biological activity. In this work, we used Isothermal Titration Calorimetry (ITC), a powerful technique for studying molecular interactions, including chiral interactions in solutions. We conducted a series of ITC measurements to investigate the heat of dilution and the heat of racemization of several amino acids (Asn, His, Ser, Ala, Met, and Phe). We also performed ITC measurements under different solute concentrations and temperatures to examine the effects of these parameters on chiral interactions, as well as the heat of dilution and racemization. The results of our measurements indicated that the heat of dilution, specifically the interactions between the solvent (water) and solute (chiral molecules), had a significant impact compared to the chiral interactions in the solution, which were found to be negligible. This suggests that the interactions between chiral molecules and the solvent play a more dominant role in determining the overall behavior and properties of the system. By studying chiral interactions in solutions, we can gain valuable insights into the behavior of chiral compounds, which can have implications in various fields, including drug design, chemical synthesis, and biological processes.

This paper proposed an optimal tracking control scheme through adaptive dynamic programming(ADP) for a class of partially unknown discrete-time nonlinear systems based on radial basis function neural network(RBF-NN). In order to acquire the unknown system dynamics, we use two RBF-NNs, the one is used to construct the identifier, and the another is used to directly approximate the steady-state control input, where a novel adaptive law is proposed to update neural network weights. While the optimal feedback control and the cost function are derived via feedforward neural networks approximating, it is proposed to regulate the tracking error, the critic network and the actor network are then trained online to obtain the solution of the associated Hamilton–Jacobi–Bellman (HJB) equation being built under the ADP framework. Simulations verify the effectiveness of the optimal tracking control technique using the neural networks.

While the importance of corporate governance has been broadly acknowledged in global financial markets and academic research, how to devise a practical evaluation system is relatively unexplored. This paper attempts to refine the Corporate Governance Evaluation System (CGES), constructed by the Taiwan Stock Exchange (TWSE) since 2014. The current CGES has several debatable issues in its complicated design (e.g., it comprises over 80 indicators in different types). To resolve those issues, this study invited ten senior domain experts (including several CEOs of financial holding companies) to retrieve 13 essential criteria from the CGES in four dimensions. And this study integrates several multiple criteria decision-making (MCDM) methods (i.e., Decision-making trial and evaluation laboratory (DEMATEL), modified VIKOR, DEMATEL-based analytical network process (DANP)) and the fuzzy evaluation technique to rank the exemplary companies. The obtained ranking is consistent with the one released from the CGES in 2017. This study conducted additional experiments to ensure the robustness of the findings. The newly devised model not only supports the ranking decisions but also provides a managerial guidance for companies to pursue systematic improvements. These findings enrich the understanding of corporate governance and contribute to gaining business sustainability for financial holding companies.

Quantum gravity theories rely on a minimal measurable length for their formulations, which clashes with the classical formulation of the uncertainty principle and with Lorentz invariance from general relativity. These incompatibilities led to the development of the generalized uncertainty principle (GUP) from string theories and its various modifications. GUP and covariant formulations of the uncertainty principle are discussed, together with implications for space-time quantization.

In the field of railroad safety, effective detection of surface cracks is critical, necessitating reliable, high-speed non-destructive testing (NDT) methods. This study introduces a hybrid Eddy Current Testing (ECT) probe, specifically engineered for railroad inspection, to address the common issue of ’lift-off noise’ due to varying distances between the probe and test material. Unlike traditional ECT methods, this probe integrates transmit and differential receiver coils, aiming to enhance detection sensitivity and minimize lift-off impact. The study optimizes ECT probes employing different driver coils, emphasizing three main objectives: a) quantitatively evaluating each probe using signal- to-noise ratio (SNR) and outlining a real-time data processing algorithm based on SNR methodology; b) exploring the frequency range proximal to the electrical resonance of the receiver coil; c) examining sensitivity variations across varying lift-off distances. The experimental outcomes indicate that the newly designed probe with figure 8-shape driver coil significantly improves sensitivity in detecting surface cracks on railroads. It achieves an impressive SNR exceeding 100 for defects with minimal dimensions of 1 mm in width and depth. Simulation results closely align with experimental findings, validating the investigation of optimal operational frequency and lift-off distance for selected probe performance, determined to be 0.3 MHz and 0.5 mm, respectively. The realization of this project would lead to notable advancements in enhancing railroad safety by improving crack detection efficiency.

As the adoption of renewable energy sources grows, ensuring a stable power balance across various time frames has become a central challenge for modern power systems. In line with the "dual carbon" objectives and the seamless integration of renewable energy sources, harnessing the advantages of various energy storage resources and coordinating the operation of long-term and short-term storage have become pivotal directions for future energy storage deployment. To address the complexities arising from the coupling of different time scales in optimizing energy storage capacity, this paper proposes a method for energy storage planning that accounts for power imbalance risks across multiple time scales. Initially, the Seasonal and Trend decomposition using the Loess (STL) decomposition method is utilized to temporally decouple actual operational data. Subsequently, power balance computations are performed based on the obtained data at various time scales to optimize the allocation of different types of energy storage capacities and assess the associated imbalance risks. Finally, the effectiveness of the proposed approach is validated through hourly applications using real-world data from a province in China over recent years.

Abscisic acid (ABA) plays a major role in promoting ripening in sweet cherry, a non-climateric fruit. Exogenous application of ABA has been performed to study fruit ripening and cracking, but this growth regulator is not used for commercial production. To determine the potential of this growth regulator to improve sweet cherry fruit quality, ABA canopy spraying was assayed in four cultivars. Canopy spraying of S-ABA significantly: 1) enhanced sweet cherry fruit color in ‘Glenred’, ‘Lapins’ and 'Bing' cultivars, but not in ‘Royal Rainier’ (a bi-colored cultivar), and 2) decreased fruit size and firmness in ‘Lapins’, ‘Bing’ and ‘Royal Rainier’. Seasonally reproducible effects were seen in ‘Lapins’ (mid/late-maturing) but not in ‘Glenred’ (early-maturing). Canopy spraying of nordihydroguaiaretic acid (NDGA) decreased color and increased fruit size in ‘Lapins’, but not in ‘Glenred’. Direct application of ABA on fruits attached to the tree, without application to the foliage, increased Lapins' fruit color without reducing size. These results suggest a localized fruit response to exogenous ABA application on fruit color development, but that a decrease in fruit size may be due to the effects of exogenous ABA on the tree canopy foliage.

Performing optimisation and scale-up studies of crystallisation systems requires accurate and computationally efficient mathematical models. The assumption of the ideal mixing conditions in batch reactors typically produce inaccurate results while the computational expense of CFD models is still prohibitively high. Therefore, in this work, a new intermediary approach is proposed that takes into account the non-ideal mixing conditions in the reactor and requires less computational resources than full CFD simulations. Starting with the Danckwerts concept of the intensity of segregation, an analogy between its application to chemical reactions and the kinetics of the crystallisation phenomena (such as nucleation and growth) has been made. As a result, the modified kinetics expressions have been derived which incorporate the effect of non-idealities present in stirred reactors. This way, based on the experimental measurements of the mixing time using the Laser Induced Fluorescence (LIF) technique, computationally more efficient mathematical models can be developed in two ways: (1) the accurate semi-empirical correlations are available for standard mixing configurations with the most often used types of impellers, (2) CFD simulations can be utilised for estimation of the mixing time; in this case it is necessary to simulate only the mixing process. The benefits offered by the LIF experimental technique have been demonstrated and some frequent problems in its application analysed. The mixing time results for configurations with and without baffles for three types of impellers and four different rotational speeds have been presented. The false shorter mixing times in the non-baffled configurations have been observed and this phenomena explained by the existence of two segregated zones in the reactor and confirmed by additional experiments. The precise measurements in these cases have been shown as difficult using the LIF technique, particularly for higher rpms. The experimental data has been compared to the preliminary simulation results obtained from the Smoothed Particle Hydrodynamics method and the standard k-ε turbulence model with the modest success. The shortcomings of the SPH model have been recognized and the directions for the future work discussed.

In an effort to enhance the efficiency and safety of open-pit mines, this study explores the optimization of end slope road parameters and slope structures, specifically focusing on unmanned driving lanes.A significant aspect of the study is the development of a truck trajectory offset model, which considers the different reaction times between automated sensors and human drivers in adapting to environmental changes. To test these concepts, the study uses numerical simulations to confirm the stability of the proposed end slope designs. Using Victory West Mine No. 1 as a case study, the research determines the optimized width for unmanned driving lanes and the maximum angle for safe steepening of end slopes. The findings indicate that the optimized unmanned lane width for NTE240 mining dump trucks is 1743 mm, allowing for a 2-degree increase in the slope angle at the south end slope. This optimization leads to a steep mining stripping volume of 3.2735 million m³ and a coal output of 2.49628 million tons, maintaining a stripping ratio of 1.31m³/t. These results demonstrate that the unmanned driving road width optimization not only ensures slope safety but also significantly boosts the economic benefits of steep mining in open-pit mines.

Optimal control is a critical tool for mechanical robotic systems, facilitating precise manipulation of dynamic processes. These processes are described through differential equations governed by a control function, addressing a time-optimal problem with bilinear characteristics. Our study utilizes the classical approach complemented by Pontryagin's Maximum Principle (PMP) to explore this inverse optimal problem. The objective is to develop an exact piecewise control function that effectively manages trajectory control while considering the effects of viscous friction. Our simulations demonstrate that the proposed control law markedly diminishes oscillations induced by boundary conditions. This research not only aims to delineate the reachability set but also strives to determine the minimal time required for the process. The findings include an exact analytical solution for the stated control problem.

In this paper, a proof similar to the Pusey-Barrett-Rudolph (PBR) theorem is given to prove that time in quantum theory is not epistemic but has ontological reality. For this, we first discuss how time can be encoded as an intrinsic property of a quantum system. We prepare a quantum state containing time as an intrinsic property and show by a PBR-type proof that time cannot be an epistemic notion. In fact, the PBR theorem implies an ontic notion of time. Indeed, if the quantum state is a physical property, then quantum state reduction is a physical process involving information destruction. In this case, quantum probabilities are intrinsic probabilities without epistemic origin, and they generate a genuinely new sequence of events. This novelty introduced by quantum probabilities can be interpreted as time.

In this paper, we study the semilinear pseudo-parabolic equations $\displaystyle u_{t} - \triangle_{\mathbb{B}}u - \triangle_{\mathbb{B}}u_{t} = \left|u\right|^{p-1}u$ on a manifold with conical singularity, where $\triangle _{\mathbb{B}}$ is Fuchsian type Laplace operator investigated with totally characteristic degeneracy on the boundary $x_{1} = 0$. Firstly, we discuss the invariant sets and the vacuum isolating behavior of solutions with the help of a family of potential wells. Then, we derive a threshold result of existence and nonexistence of global weak solution: for the low initial energy $J(u_{0})<d$, the solution is global in time with $I(u_{0}) >0$ or $\displaystyle\Vert \nabla_{\mathbb{B}}u_{0}\Vert_{L_{2}^{\frac{n}{2}}(\mathbb{B})} = 0$ and blows up in finite time with $I(u_{0}) < 0$; for the critical initial energy $J(u_{0}) = d$, the solution is global in time with $I(u_{0}) \geq0$ and blows up in finite time with $I(u_{0}) < 0$. The decay estimate of the energy functional for the global solution and the estimates of the lifespan of local solution are also given.

The enormous growth in the penetration of electric vehicles (EVs), has laid the path to advancements in the charging infrastructure. Connectivity between charging stations is an essential prerequisite for future EV adoption to alleviate users’ “range anxiety”. The existing charging stations fail to adopt power provision allocation and scheduling management. To improve the existing charging infrastructure data based on real-time information and availability of reserves at charging stations could be uploaded to the users to help them locate the nearest charging station for an EV. This research article focuses on an a interactive user application developed through SQL and PHP platform to allocate the charging slots based on estimated battery parameters, which uses data communication with charging stations to receive the slot availability information. The proposed server-based real-time forecast charging infrastructure avoids waiting times and its scheduling management efficiently prevents the EV from halting on road due to battery drain out. The proposed model is implemented using a low-cost microcontroller and the system etiquette tested.

In this paper, we study a one-dimensional Bresse-Cattaneo system with infinite memories and time-dependent delay term (the coefficient of which is not necessarily positive) in the internal feedbacks. First, it is proved that the system is well-posed by means of the Hille-Yosida theorem under suitable assumptions on the relaxation functions. Then, without any restriction on the speeds of wave propagations, we establish the exponential or general decay result by introducing suitable energy and Lyapunov functionals.

Underwater Sensor Networks (UWSNs) can enable a broad range of applications such as resource monitoring, disaster prevention, and navigation-assisted. It is especially relevant for sensor nodes location in UWSNs. Global Positioning System (GPS) is not suitable for using in UWSNs because of the underwater propagation problems. Hence some localization algorithms based on the precise time synchronization between sensor nodes have been proposed which are not feasible for UWSNs. In this paper, we propose a localization algorithm called Two-Phase Time Synchronization-Free Localization Algorithm (TP-TSFLA). TP-TSFLA contains two phases, namely, range-based estimation phase and range-free evaluation phase. In the first phase, we address a time synchronization-free localization scheme base on the Particle Swarm Optimization (PSO) algorithm to decrease the localization error. In the second phase, we propose a Circle-based Range-Free Localization Algorithm (CRFLA) to locate the unlocalized sensor nodes which cannot obtain the location information through the first phase. In the second phase, sensor nodes which are localized in the first phase act as the new anchor nodes to help realize localization. Hence in this algorithm, we use a small number of mobile beacons to help achieve location without any other anchor nodes. Besides, to improve the precision of the range-free method, an extension of CRFLA by designing a coordinate adjustment scheme is updated. The simulation results show that TP-TSFLA can achieve a relative high localization ratio without time synchronization.

This work introduces a new architecture for a time-domain feedback-based beamformer designed to meet real-time processing demands. The primary goal of this design is to locate reflective sources by estimating their direction of arrival (DOA) and signal range. Incorporating a feedback mechanism in this architecture is a unique aspect that refines localization precision. We conduct an in-depth analysis highlighting their respective benefits and limitations to compare the effectiveness of time-domain feedback beamforming against conventional time-domain methods. Our evaluation of the proposed architecture, based on critical performance indicators such as peak-to-sidelobe ratio, mainlobe width, and directivity factor, demonstrates its ability to improve beamformer effectiveness significantly.

The steady-state multiplicity of the porous, non-isothermal, catalyst pellet when two parallel and consecutive chemical reactions take place was analysed in this work. The geometry selected for the catalyst pellet is finite hollow cylinder. A numerical multigrid continuation technique with the preconditioned conjugate gradient squared as coarse grid solver was used. The continuation parameter is the dimensionless adiabatic heat rise (Prater number) for the first chemical reaction. The effect of the other governing parameters was analysed and the results are compared to those provided by the single chemical reaction.

This article develops a multi-perspective view on motivations and methods for tobamovirus purification through the ages, and presents a novel efficient, easy-to-use approach that can be well-adapted to different species of native and functionalized virions. We survey the various driving forces prompting researchers to enrich tobamoviruses: from the search for the causative agents of mosaic diseases in plants to their increasing recognition as versatile nanocarriers in biomedical and engineering applications. Best practice and also rarely applied options for the serial processing steps required for successful isolation of tobamoviruses are then reviewed. Adaptations for distinct particle species, pitfalls and 'forgotten' or underrepresented technologies are considered as well. The article is topped off with our own development of a method for virion preparation, rooted in historical protocols. It combines selective re-solubilization of polyethylene glycol (PEG) virion raw precipitates with density step gradient centrifugation in biocompatible iodixanol formulations, yielding ready-to-use particle suspensions. This newly established protocol and some considerations for perhaps worthwile further developments could serve as putative stepping stones towards preparation procedures appropriate for routine practical uses of the multivalent soft-matter nanorods.

A novel concept of a finned piston system is presented and analyzed where the compression heat is continuously extracted from the compression chamber. The resulting compression characteristic moves in direction of an isothermal process, reducing so the temperature of the compressed fluid in the compression chamber and reducing the necessary mechanical work for the process. The finned piston concept consists in an integrated heat exchanger inside of the chamber and being constituated of imbricated flat fins placed on the stator part and on the mobile piston. The internal heat exchange surface is strongly increased in comparison with a classical piston/cylinder. The energetic performance of the new system is evaluated with the help of simulation. Pressures, forces and temperature of the compressed gas are simulated as well as the mechanical work needed. The different curves are compared with adiabatic and isothermal characteristics.

The degree of ore rock fragmentation of mine blasting is an important index for evaluating the effect of engineering blasting. In order to study the effect of millisecond delayed blasting on the internal fragmentation of the ore rock, LS-DYNA numerical simulation software was used to obtain the damage characteristics of the ore rock in the blasting area using the RHT model. The Mohr-Coulomb strength damage criterion was applied to analyze the internal stress state of the ore rock, and the effects of 25ms, 50ms and 75ms delay time conditions on ore rock fragmentation were studied. The results show that, within a certain range of delay time, the degree of rock fragmentation increases with the increase of delay time. The stress state in the ore rock due to blasting is strengthened with the increase of delay time in the direction of the blast hole, which shows that the stress concentration is strengthened from the excavation face to the interior of the ore rock. The damage and the degree of fragmentation show a characteristic relationship of 25ms＜50ms＜75ms, which is verified by carrying out blasting experiments on site.

A major limitation of near-infrared spectroscopy (NIRS) is its high sensitivity to the scalp and low sensitivity to the brain of adult humans. In the present work we use multi-distance hyperspectral NIRS (hNIRS) to investigate the optimal source-detector distances, range of wavelengths, and analysis techniques to separate cerebral responses to 30-s breath holds (BHs) from the responses in the superficial tissue layer in healthy adult humans. We observed significant responses to BHs in the scalp hemodynamics. Cerebral responses to BHs were detected in the cytochrome C oxidase redox (rCCO) at 4 cm without using data from the short-distance channel. Using the data from the 1 cm channel in the two-layer regression algorithm showed that hemodynamic and rCCO responses also occurred at 3cm. We found that the waveband 700-900 nm was optimal for the detection of cerebral responses to BHs in adults.

The rural population percentage decreased from 82.7% to 68.9% in 2011, even though there is an increase in the total rural population, which stands at 833.7 million, and the rural population were now more than three times compared to the population seven decades ago. Another observation is the decrease in cultivators percentage from 71.9% to 45.1 %, while agriculture labour increase from 28.1% to 54.9% during the same period. Despite the increase in irrigated land and net area sown, the average holdings' size under the farmers is continuously decreasing, and it requires a study to look into the reasons. The research probes the role of Minimum Support Price (MSP) in supporting farmers and measuring market price above MSP needed to help marginal and small farmers remain above the poverty level. It explains how different market rates above MSP have a different impact on different categories of agriculture landholding. The study works on developing a common model that relates the impact of MSP on different farmers categories. The model can be generalized to all crops and regions and useful in designing policies that focus on uplifting the income of agricultural farmers.

Structural health monitoring has been studied by a number of researchers as well as various industries to keep up with the increasing demand for preventive maintenance routines. This work presents a novel method for reconstruct prompt, informed strain/stress responses at the hot spots of the structures based on strain measurements at remote locations. The structural responses measured from usage monitoring system at available locations are decomposed into modal responses using empirical mode decomposition. Transformation equations based on finite element modeling are derived to extrapolate the modal responses from the measured locations to critical locations where direct sensor measurements are not available. Then, two numerical examples (a two-span beam and a 19956-degree of freedom simplified airfoil) are used to demonstrate the overall reconstruction method. Finally, the present work investigates the effectiveness and accuracy of the method through a set of experiments conducted on an aluminium alloy cantilever beam commonly used in air vehicle and spacecraft. The experiments collect the vibration strain signals of the beam via optical fiber sensors. Reconstruction results are compared with theoretical solutions and a detailed error analysis is also provided.

Real estate industry is related to the national economy and people's livelihood，characterized by a high degree of financial intensity. The enterprises in this industry need certain financial ability and large shareholder controlling ability to support their survival. However，due to the multiple adverse impacts of current state policies，banks and private capital，the credit crunch，the sudden decrease in withdrawn funds and the limitation of internal financing，the problem of capital restraint of real estate enterprises has become more and more serious. From the perspective of corporate governance，this paper studies the interaction among financial constraints，ownership concentration and corporate performance under different shareholding states by analyzing the quantitative characteristics of equity structure，and looks for the appropriate range of the largest shareholder holding ratio，which has considered the financial performance and risk. It is found that raising the ownership concentration can effectively ease the financing constraints and improve the performance of enterprises，both of which are significant under the state of high ownership concentration， while the financial constraints play a significant intermediary effect under the State of absolute holding， while in the decentralized state of ownership，there is a significant regulatory effect，and the interaction of the three will be different due to the size of the enterprise.

In this paper, a polyacrylic elastomer latex with butyl acrylate (BA) as the core and methyl methacrylate (MMA) copolymerized with glycidyl methacrylate (GMA) as the shell, named poly(BA-MMA-GMA) (PBMG), was synthesized by seeded emulsion polymerization. Cellulose nanocrystal (CNC) was dispersed in the polyacrylic latex to prepare PBMG/CNC dispersions with different CNC contents. The dried product was mixed with polylactic acid (PLA) to fabricate PLA/PBMG/CNC blends. The addition of PBMG and PBMG/CNC improved the mechanical properties of the PLA matrix. Differential scanning calorimetry (DSC) was used to investigate the non-isothermal crystallization kinetics. The Avrami equation modified by Jeziorny, and the Ozawa, and Mo’s equations were used to analyze the nonisothermal crystallization kinetics of PLA and its blends. Analysis of crystallization halftime of nonisothermal conditions indicated that the overall rate of crystallization increased significantly at 1 wt% content of CNC. This seemed to result from the increase of nucleation density and the acceleration of segment movement in the presence of CNC component. This phenomenon was verified by polarizing microscope observation.

Additive manufacturing (AM) techniques are widely investigated for the cost-effective use of titanium (Ti) alloys in various aerospace applications. One of the AM techniques developed for such applications is plasma transferred arc solid free-form fabrication (PTA-SFFF). Materials manufactured through AM techniques often exhibit anisotropies in mechanical properties due to the layer-by-layer material build. In this regard, the present study investigates the isothermal directional fatigue of Ti-TiB metal matrix composite (MMC) manufactured by PTA-SFFF. This investigation includes rotating beam fatigue test, electron microscopy, and fatigue calculations. The fatigue experiments were performed at 350 ºC using specimen with the test axis oriented diagonally (45º) and parallel (90º) to the AM builds directions. The fatigue values from the current experiments along with literature data find that Ti MMC manufactured via PTA-SFFF exhibit fatigue anisotropy reporting highest strength in 90º and lowest in perpendicular (0º) AM build directions. Further, the electron microscopy investigations on 0º, 45º, and 90º AM build specimens reveal frequent TiB clusters in all three AM build directions and suggest that the spread of these TiB clusters play a role in fatigue anisotropy. Moreover, the fatigue calculations were performed using both the Paris’ and recently reported modified Paris’ equations. Comparison of R^2 values for these calculations show that modified Paris’ equation predicts the fatigue life of AM Ti-TiB MMC more accurately than the Paris’ equation.

We report a small footprint cost-effective isothermal rapid DNA amplification system, with integrated microfluidics for automated sample analysis and detection of SARS-CoV-2 in human and environmental samples. Our system measures low-level fluorescent signal in real-time during amplification, while maintaining the desired assay temperature, on a low power, portable system footprint. A unique soft microfluidic chip design was implemented to mitigate thermocapillary effects and facilitate optical alignment for automated image capture and signal analysis. The system-on-board prototype coupled with the LAMP primers designed by BioCoS, is sensitive enough to detect viral loads of SARS-CoV-2 in a broad concentration range corresponding to a threshold cycle range of 16 to 39. Clinical specimens were tested at Kingston Health Sciences using a clinically validated PCR assay and variants were determined using whole genome sequencing.

This study aimed to evaluate the effects of Blazepod technology when incorporated with various training regimens on the essential elements of physical fitness in volleyball, such as agility, speed, visual response time, and vertical leap. Thirty-six participants (age :17.33±0.48 y, height: 183.78±6.34 cm, weight: 77.14±5.16 kg) were in-volved in this study. In randomized design, three equal groups with two experimental groups and one control group were involved in the study over a period of six weeks: (GE1) used Blazepod technology to workout at a low level; (GE2) used Blazepod technology to workout at a higher intensity; (CG) did not employ Blazepod technology, but it adhered to the same fundamental training curriculum. We conducted agility, speed, reaction time, and vertical jump tests before, midway and after the study to determine optimal training volume, intensity, and frequency. A significant main effect of time (P0.01), and time×group interaction (P>0.001) were found for all tests. Post hoc test showed that the two experimental groups gadget significantly improved in all performance variables (P

Isothermal Nucleic Acid Amplification based-Lateral Flow Testing (INAA-LFT) has emerged as a robust technique for on-site pathogen detection, providing a visible indication of pathogen nucleic acid amplification that rivals or even surpasses the sensitivity of real-time quantitative PCR. The isothermal nature of INAA-LFT ensures consistent conditions for nucleic acid amplification, establishing it as a crucial technology for rapid on-site pathogen detection. However, despite its considerable promise, the widespread application of isothermal INAA amplification-based lateral flow testing faces several challenges. This review provides an overview of the INAA-LFT procedure, highlighting its advancements in detecting plant viruses. Moreover, the review underscores the imperative to address existing limitations and emphasizes ongoing research efforts dedicated to enhancing the applicability and performance of this technology in the realm of rapid on-site testing.

Rice false smut caused by Ustilaginoidea virens is one of the most devastating diseases on rice worldwide, which results in serious reduction of rice quality and yield. As an airborne fungal disease, early diagnosis of rice false smut, monitoring the epidemics and distribution of its pathogens, is particularly important to management the infection. In this study, a quantitative loop-mediated isothermal amplification (q-LAMP) method for the U. virens detection and quantifying was developed. This method has higher sensitivity and efficiency compared to quantitative real-time PCR (q-PCR) method. The species-specific primer sets UV-2 used was design based on the unique sequence of U. virens ustiloxins biosynthetic gene (NCBI accession number: BR001221.1). The q-LAMP assay was able to detect a concentration of 6.4 spores/mL at an optimal reaction temperature of 63.4℃ within 60 min. Moreover, the q-LAMP assay can even achieve accurate quantitative detection when there were only 9 spores on the tape. A linearized equation for the standard curve, y =-0.2866x + 13.829 (x is the amplification time, the spore number = 100.65y), was established for detection and quantifying of U. virens. In field detection applications, this q-LAMP method is more accurate and faster than traditional observation method. Collectively, this study has established a powerful and simple monitoring tool for U. virens, which provide valuable technical supports for forecast and management of rice false smut, and theoretical basis for precise fungicide application.

Background: Dendrobium officinale is not only an ornamental plant, but also a valuable medicinal herb that is both effective and widely used in traditional Chinese medicine. However, distinguishing D. officinale from other Dendrobium species is usually a difficult task that need much time and complex technologies due to their very similar external morphologies. The aim of this study is to develop a fast, even on-spot approach to identify D. officinale. Methods: We used DNA barcode-based loop-mediated isothermal amplification (LAMP) method with species-specific LAMP primers targeting the internal transcribed spacer (ITS) region of the rDNA of D. officinale. LAMP reaction time and temperature were optimized and the specificity and sensitivity of LAMP species-specific primers were assessed. Results: This technique showed a high specificity and sensitivity to amplify the genomic DNA of D. officinale and allowed for rapid amplification (within 40 min) of the ITS region under a constant and mild temperature range of 65 °C without using thermocyclers. Besides, by using SYBR® Green I dye as the color developing agent, the color change was easily observed with naked eye. Reaction mixture containing DNA of D. officinale changed from orange to green, while the other Dendrobium species and the negative control retained original orange color. The specificity of this LAMP-based method was confirmed by testing 17 samples of D. officinale and 32 adulterant samples from other Dendrobium species. Conclusions: This LAMP-based rapid identification method does not require expensive equipment or specialized techniques and can be used in field surveys for accurate and fast on site identification.

We review time expansion wave theory and refine our model showing it to accurately match observed cosmological luminosity data. The theory augments general relativity to create a container within which quantum effects can be explained by treating time as an artefact of a fourth spatial dimension that we observe as the expansion of the universe. This leads us to explain mass creation, the speed of light limit, gravity, black holes without singularities and other macroscopic effects. Our model leads to an expansion velocity of 6.87 0.36 × 106 ms-1, which results in a Hubble expansion rate constant of 71.3 3.7 km/s/Mpc. Because of the finite window of time in which we exist, an extra a degree of freedom is available leading to interesting interpretations at the subatomic level. At this size range, then a spin is allowed within the time dimension explaining why wave particle duality occurs and explains the electromagnetic force and other quantum mechanical properties. It provides a solution to the double slit conundrum and can explain how quantum entangled partners can behave in a quantum way and pass seemingly time-defying information. The potential quantitative origin of the fine structure constant which governs the size of the electromagnetic force is also strongly indicated by this theory.

In this paper, we study the asymptotic behavior of the sequential empirical process and the sequential empirical copula process, both constructed from residuals of multivariate stochastic volatility models. Applications for the detection of structural changes and specification tests of the distribution of innovations are discussed. It is also shown that if the stochastic volatility matrices are diagonal, which is the case if the univariate time series are estimated separately instead of being jointly estimated, then the empirical copula process behaves as if the innovations were observed; a remarkable property. As a by-product, one also obtains the asymptotic behavior of rank-based measures of dependence applied to residuals of these time series models.

A multiscale model that enables quantitative understanding and prediction of the size effect on scattering properties of micro- and nanostructures is crucial for the design of LED surface textures optimized for high light extraction efficiency (LEE). In this paper, a hybrid process for combining full-wave finite-difference time-domain simulation and a ray-tracing technique based on a bidirectional scattering distribution function model is proposed. We apply this method to study the influence of different pattern sizes of a patterned sapphire substrate on GaN-based LED light extraction from the microscale to the nanoscale. The results show that near-wavelength–scaled patterns with strong diffraction are not expected to enhance LEE. By contrast, microscaled patterns with optical diffusion behavior have the highest LEE at a specific aspect ratio, and subwavelength-scaled patterns that have antireflection properties show marked enhancement of LEE for a wide range of aspect ratios.

This paper proposes an innovative mechatronic piezo-actuated module to control vibrations in modern machine tools. Vibrations represent one of the main issues that compromise seriously the quality of the workpiece. The active vibration control (AVC) device is composed by a host part integrated with sensors and actuators synchronized by a regulator, able to make a self-assessment and adjust to the environmental alteration. This study presents the mechatronic model based on the kinematic and dynamic analysis of the AVC device. To ensure a real time performance, a H2-LQG controller has been developed and validated by simulations involving machine tool, PZT actuator and controller models. The Hardware-in-the-loop (HIL) architecture is adopted to control and attenuate the vibrations. A set of experimental tests has been performed to validate the AVC module on a commercial machine tool. The feasibility of the real time vibration damping is demonstrated and the simulation accuracy is evaluated.

This paper is concerned with a hydraulic cylinder directly controlled by a variable speed fixed displacement pump. The considered configuration is referred to as a one-motor-one-pump (1M1P) motor-controlled hydraulic cylinder (MCC). A 1M1P MCC with a hydraulically driven passive load-holding function enabled by controlled system pressures is proposed. The proposed load-holding functionality works if there is a standstill command, a loss of power supply, or a hose rupture. Additionally, this paper conducts a comprehensive analysis of the proposed system's operation and load-holding function across four quadrants. Simulation results demonstrate the four-quadrant operation and good load-holding performance under the aforementioned scenarios. In conclusion, the proposed 1M1P MCC can be successfully used on practical applications characterized by overrunning loads and four quadrant operation.

Biodiesel has several drawbacks, such as being prone to oxidation, having reduced stability, and having limited storage time. Antioxidants compatible with biodiesel are being used to address its drawbacks. The use of antioxidants in biodiesel has a significant impact on the environment and economy, especially in promoting sustainable energy. The study used blends consisting of 20% biodiesel and 80% diesel fuel. Isatin-thiosemicarbazones were tested as additives in blends at a concentration of 3000 parts per million (ppm) using an oxifast device. Comparing them to the chemical antioxidant Trolox. FT-IR, DSC, and TGA were used to characterize these samples. DSC measured sample crystallization temperatures (Tc). Samples with antioxidants showed decreased values compared to the non-antioxidant diesel sample D100. Several DSC tests were conducted to determine the antioxidant strengths of various samples. The results showed that the FT-IR spectrum's antioxidant effect regions grow clearer with antioxidants. The extra antioxidant is effective. Biodiesel's oxidative stability improves with isatin-thiosemicarbazones at varying concentrations. The kinetics of thermal decomposition of isatin-thiosemicarbazones under non-isothermal conditions have been determined using the Kissinger, Ozawa, and Boswell techniques. The activation energies of compounds 1 and 2 were calculated 137–147 kJ mol-1 and 173–183 kJ mol-1, respectively.

The emergence of the COVID-19 pandemics prompted a fast development of novel diagnostic methods of the etiologic virus SARS-CoV-2. Methods based on CRISPR-Cas systems have been particularly promising because they can achieve a similar sensitivity and specificity to the golden standard RT-qPCR, especially when coupled to an isothermal pre-amplification step. Furthermore, they have also solved inherent limitations of RT-qPCR that impede its decentralized use and deployment in the field, such as the need for expensive equipment, high cost per reaction, and delivery of results in hours, among others. In this review, we evaluate publicly available methods to detect SARS-CoV-2 that are based on CRISPR-Cas and isothermal amplification. We critically analyze the steps required to obtain a successful result from clinical samples and pinpoint key experimental conditions and parameters that could be optimized or modified to improve clinical and analytical outputs. The COVID outbreak has propelled intensive research in a short time, which is paving the way to develop effective and very promising CRISPR-Cas systems for the precise detection of SARS-CoV-2. This review could also serve as an introductory guide to new labs delving into this technology.

This work probes the combined effects of magnetic field and viscous dissipation on heat field and examine the second law analysis (entropy generation) in an electrically conducting fluid under the effect of wall mass transfer over continuous stretched non-isothermal surface with variable viscosity. The viscosity of the fluid is assumed to be an inverse linear function of temperature. The governing equation for the problem are changed to dimensionless ordinary differential equations by using similarity transformation and solved numerically by using Rung Kutta and Shooting technique. Velocity, concentration and temperature distribution are obtained and used to compute the entropy generation and the Bejan number in the flow field. The effect of variable viscosity, Schmidt number, Hartman and Reynolds number on the velocity, concentration, temperature, entropy generation and Bejan number are studied and discussed.

A time-sequential working, spatially multiplexed autostereoscopic 3D display design consisting of a fast switchable RGB-color filter array is presented. The wavelength-selective filter barrier emits the light from a display over a larger active area than common autostereoscopic barrier displays. An optical modelling of wavelength-selective barriers has been used for instance to calculate the light ray distribution properties of that arrangement. To find well working display designs, automated searches by simulation and computational evaluation has been proceeded. Wavelength-selective filter barrier arrangements exhibit characteristics different from common barrier displays with similar barrier pitch and ascent. In particular, these constructions show strong angular luminance dependency under barrier inclination specified by correspondent slant angle. In time-sequential implementation it is important to avoid that quick eye or eyelid movement lead to visible color artifacts. In the millisecond regime tunable liquid crystal Fabry-Pérot color filters for the colors red, green and blue are presented. They consist of a sub-micrometer thick nematic layer sandwiched between dielectric mirrors and ITO-electrodes. These cells shall switch narrow-banding light of red, green or blue. An array for a glasses-free 3D display has to be equipped with several thousand switchable filter elements having different color apertures. The newly introduced design is usable as a multi user display as well as a single user system with user adaptive control.

When dealing with limited sample sizes or missing values in time series data, achieving high accuracy in forecasting becomes challenging. This challenge is particularly common in wind energy forecasting, where many wind farms lack complete data. In this paper, we employ the widely-used ARIMA (Autoregressive Integrated Moving Average) model for time series forecasting. To address the difficulties posed by limited sample sizes and missing values, we adopt a unique approach by utilizing multiple ARIMA models for different datasets. A key distinction from other multiple models methods for time series forecasting lies in each model within our approach using its own dataset, making the fusion process more intricate. To overcome this, we incorporate neural networks and two techniques for model fusion: direct fusion with a learning mechanism and compensation for missing data through training. For each ARIMA model, we introduce a noise estimation method to circumvent the white noise assumptions inherent in ARIMA models. Finally, we apply these methods to wind energy prediction, and our experimental results showcase a significant enhancement in forecasting accuracy.

This paper investigates the feasibility of a backend design for real-time, multiple-channel processing digital phased array system, particularly for high-performance embedded computing platforms constructed of using general purpose digital signal processors. Frist, we obtained the lab-scale backend performance benchmark from simulating beamforming, pulse compression, and Doppler filtering based on MicroTCA chassis using Serial RapidIO protocol in backplane communication. Next, a field-scale demonstrator of a multifunctional phased array radar is emulated by using the similar configuration. Interestingly, the performance of a barebone design is compared to that of emerging tools that systematically take advantage of parallelism and multicore capabilities, including Open Computing Language.

Expressions for the axial pressure profiles in a cylindrical channel and between parallel plates or a rectangular channel with large aspect ratio, with Maxwell slip gas flow are derived from first principles. The resulting expressions, which only involve the inlet and outlet pressures and the channel dimensions, will be useful in modelling or simulations of channel flows at Knudsen numbers in the range 0.001–0.1, such as in MEMS and NEMS. The expression for a cylindrical channel is validated by deriving from it an expression for the channel mass flow, which is shown to agree with a known expression for the mass flow through cylindrical channels with Maxwell slip flow. The expression for flow between parallel plates is found to agree with the zeroth order relation derived by Arkilic et al. using perturbation analysis. The effect of the accommodation coefficient on the pressure profile in a cylindrical channel is shown.

Obesity poses significant challenges in rural communities worldwide due to limited resources and healthcare access. Practical, innovative, and culturally sensitive approaches are essential. Time-Restricted Eating (TRE), aligning food intake with circadian rhythms, emerges as a promising strategy. By restricting eating to specific time windows, TRE synchronizes with the body's internal clock, offering potential metabolic health benefits. This review examines TRE's potential in rural obesity management, highlighting its simplicity and scalability. While TRE may address rural health disparities, cultural considerations and challenges such as undernutrition must be acknowledged for effective implementation. Overall, TRE shows promise in improving metabolic health and well-being in rural populations.

Abstract: — management of the Continuous Stirred Tank Reactor (CSTR) operation has proven to be a difficult undertaking due to the complex and ever-changing nature of its behavior, which is both nonlinear and dynamic, which is further compounded by its instability. Attempts have been made to use Proportional-Integral-Derivative (PID) controllers for such processes, but the performance is often poor due to the inherent limitations of the controllers. In contrast, heuristic algorithms have been employed to tune the controllers, but these methods can only provide optimal performance for a restricted range of parameter variations. This paper presents a novel approach that involves using a conventional gain scheduling PID controller in combination with a fuzzy gain scheduling (FGS) controller method to calibrate set-point weighted PID controllers for the CSTR process. The paper outlines the design of the controllers and evaluates their performance by subjecting them to varying input signals within the given bandwidth.

Abscisic acid (ABA) is a conserved “stress hormone” in unicellular organisms, plants and animals. In mammals, ABA and its receptors LANCL1 and LANCL2 stimulate insulin-independent cell glucose uptake and oxidative metabolism: overexpression of LANCL1/2 increases, and their si-lencing conversely reduces, mitochondrial number, respiration and proton gradient dissipation in muscle cells and in brown adipocytes. We hypothesized that the ABA/LANCL hor-mone/receptors system could be involved in thermogenesis. Heat production by LANCL1/2-overexpressing vs. double-silenced cells was compared in rat H9c2 cardiomyocytes with two different methods: differential temperature measurements using sensitive thermistor probes, and differential isothermal calorimetry. Results indicate that overexpressing cells generate an approx. double amount of thermal power compared with double-silenced cells, and that addition of ABA further doubles heat production in overexpressing cells. With the temperature probes, we find a time-scale of approx. 4 min for thermogenesis to “turn on” after nutrient addition. These results identify the ABA/LANCL hormone receptors system as a hitherto unknown regu-lator of cell thermogenesis. Pharmacologic means of increasing metabolic energy dissipation are considered a promising strategy to reduce oxidative stress and lipid accumulation at a cellular and organismic level: from this study, LANCL1-2 proteins emerge as targetable controllers of ther-mogenesis through their natural ligand ABA.

We investigated the response of the Manila clam Venerupis philippinarum to possible temperature and salinity changes in a holding facility. First, clams were exposed to four temperatures for 15 days. Valve closure and survival of clams exposed to seawater at 18℃ were higher than that of those exposed to seawater at 24℃. Second, clams were exposed to six salinities for 15 days. Survival of clams exposed to two salinity fluctuation conditions (24–30 and 27–24 psu) was lower than that of clams exposed to constant 30 psu conditions. Valve closures of clams exposed to constant low salinity conditions (24 psu) and two salinity fluctuation conditions (24–30 and 27–24 psu) were higher than of those exposed to constant 30 psu conditions. Lastly, clams were exposed to two different temperatures and three different salinities conditions for 8 days. Valve closure and survival decreased significantly under the combination of 24℃ and 18 psu. These results suggest that an increase in temperature or a wider range of salinity fluctuations are detrimental to the survival of the Manila clam. The synergistic effect of temperature and salinity stressors may decrease the survival period of clams compared to the effect of a single stressor.

This work investigated the isothermal holding time dependence of the densification, microstructure, weight loss and tensile properties of Fe-Mn-Si powder compacts. Elemental Fe, Mn and Si powder mixtures with a nominal composition of Fe-28Mn-3Si (in weight percent) were ball milled for 5h and subsequently pressed under a uniaxial pressure of 400 MPa. The compacted Fe-Mn-Si powder mixtures were sintered at 1200 ℃ for 0, 1, 2 and 3 h, respectively. In general, the density, weight loss and tensile properties increased with the increase of isothermal holding time. A significant increase in density, weight loss and tensile properties occurred in the compacts isothermally holding for 1 h, as compared to those with no isothermal holding. However, further extension of isothermal holding time (2 and 3 h) only played a limited role in promoting the density and tensile properties. The weight loss of the sintered compacts was mianly caused by the sublimation of Mn in Mn depletion region on the surface layer of the sintered Fe-Mn-Si compacts. The length of the Mn depletion region increased as isothermal holding time increased. A single α-Fe phase was detected on the surface of all the sintered compacts, and the locations beyond the Mn depletion region were comprised of a dual dominant γ-austenite and minor ε-martensite.

Background: Patients with thromboembolic disease, prosthetic valves, or coagulation issues are commonly prescribed anticoagulants and antiplatelets. Although common professional oral hygiene might not represent a health concern for these patients, anticoagulant and antiplatelet medication might constitute a challenge for dentists and dental hygienists since possible prolonged bleeding might interfere with dental procedures. The aim of the present study was to investigate the bleeding time of different anticoagulants and antiplatelets during a professional hygiene session adapting the Ivy test to the oral environment; Methods: 93 consecutive patients undergoing professional oral hygiene were recruited. Debridement during oral hygiene was performed using ultrasonic mechanical instrumentation, and bleeding sites were assessed and treated with gentle pressure using sterile gauzes. The time for bleeding cessation was recorded. Patients were categorized into six groups based on their drug intake, Control: no anticoagulants or antiplatelets DTI: direct thrombin inhibitors (dabigatran) AntiXa: directa factor Xa inhibitors (endoxaban, apixaban, rivaroxaban) VKA: vitamin K antagonists (warfarin, acenocoumarol) SAPT: single anti-platelet therapy (acetylsalicylic acid or clopidogrel) DAPT: dual anti-platelet therapy (acetylsalicylic acid and clopidogrel). Bleeding time was measured in seconds and mean values were assessed among the different groups. Differences between groups were investigated with Kruskal-Wallis test followed by Dunn’s post-hoc correction for multiple comparisons or two-way ANOVA followed by Dunnett post-hoc; Results: Control patients presented the lowest bleeding time 50 sec, followed by AntiXa (98), SAPT (105), DTI (120), DAPT (190) and VKA (203). A statistically significant difference was present among control and DTI (p=0.004), VKA (p&lt;0.001), DAPT (p&lt;0.001). Conclusions: Based on the present outcomes, an increased risk of prolonged bleeding emerged in patients taking VKA and DAPT. However, bleeding did not interfere with the oral hygiene ses-sion The optimal period for dental treatment of these patients should be 2-3 hours before the next dose, without the need to temporarily suspend the medication.

Equines play an important role throughout the world, whether for work, culture, or leisure, providing an ever-growing significant contribution on the economy. The increase in importation and movement of horses, both nationally and internationally, has inevitably allowed for the global equine industry to grow. Subsequently however, the potential for transmission of fatal equine bacterial diseases has also escalated, and devasting outbreaks continue to occur. To prevent such events, disease surveillance and diagnosis must be heightened throughout the industry. Current common, or "gold-standard" techniques, have shown to be inadequate at times, thus requiring newer technology to impede outbreaks. Loop-mediated isothermal amplification (LAMP) has proven to be a reliable, rapid, and accessible tool in both diagnostics and surveillance. This review will discuss equine bacterial diseases of biosecurity relevance and their current diagnostic approaches, as well as their respective LAMP assay developments. Additionally, we will provide insight regarding newer technology and advancements associated with this technique, and their potential use for the outlined diseases.

Migratory flows and international travel are triggering an increase in imported cases of schistosomiasis in non-endemic countries, with serology being the recommended method for screening migrants. The present study aims to evaluate, for the first time, the LAMP technique on patients’ urine samples for the diagnosis of imported schistosomiasis in a non-endemic area in comparison to a commercial immunochromatographic test and microscopic examination of feces and urine. A prospective observational study was conducted in sub-Saharan migrants attending at the Tropical Medicine Unit, Almería, Spain. For schistosomiasis diagnosis, serum samples were tested using an immunochromatographic test (Schistosoma ICT IgG-IgM). Stool and urine samples were examined by microcopy. Urine samples were evaluated by combining three LAMP assays for the specific detection of Schistosoma mansoni and S. haematobium, and an assay for the genus Schistosoma. To evaluate the diagnostic accuracy of Schistosoma-LAMP in comparison to microscopy and Schistosoma ICT IgG-IgM test, a Latent Class Analysis (LCA) was performed. A total of 115 patients were included; 21 patients (18.3%) were diagnosed with schistosomiasis confirmed by microscopy, with S. haematobium being the most frequent species identified (18/115; 15.7%). The Schistosoma ICT IgG-IgM test resulted 100% positive and Schistosoma-LAMP was 61.9% positive, reaching as high as 72.2% for S. haematobium. The sensitivity and specificity estimated by LCA, respectively, were: 92% and 76% for Schistosoma ICT IgG-IgM, 68% and 44% for Schistosoma-LAMP and, 46% and 97% for microscopy. The Schistosoma-LAMP technique presented a higher sensitivity than microscopy for the diagnosis of imported urinary schistosomiasis, which could improve the diagnosis both in referral centers and in centers with limited experience or scarce resources and infrastructure.

Using optical characterization, it is evident that the spin state of the spin crossover molecular complex [Fe{H2B(pz)2}2(bipy)] (pz = tris (pyrazol-1-1y)-borohydride, bipy = 2,2’-bipyridine) depends on the ferroelectric polarization of an adjacent thin film of the polymer ferroelectric polyvinylidene fluoride-hexafluoropropylene (PVDF-HFP). The UV-Vis spectroscopy reveals that room temperature switching of [Fe{H2B(pz)2}2(bipy)] molecules in bilayers of PVDF-HFP/[Fe{H2B(pz)2}2(bipy)] as a function of ferroelectric polar polarization. The electric polarity dependence of bilayers of PVDF-HFP/[Fe{H2B(pz)2}2(bipy)] shows a strong dependence on the thickness of the PVDF-HFP layer. The PVDF-HFP/[Fe{H2B(pz)2}2(bipy)] interface may affect polarization retention in the PVDF-HFP thin film limit.

This paper presents the results of investigations into the pyrolysis of waste polypropylene in a laboratory fixed-bed batch reactor. The experiments were designed and verified in such a way as to allow the application of the Response Surface Methodology (RSM) in the development of an empirical mathematical model that quantifies the impacts mentioned above. The influence of the mass of the raw material (50, 100 and 150 g), together with the reactor temperature (450, 475 and 500 °C) and the reaction time (45, 50 and 75 min) was examined. It has been shown that the mass of the raw material, i.e. the filling volume of the reactor, has a significant influence on the pyrolysis oil yield. This influence exceeds the influence of reactor temperature and reaction time. This was explained by observing the temperature change inside the reactor at three different spots at the bottom, middle and top of the reactor. Recorded temperature diagrams show that with greater masses of feedstock, local overheating occurs in the middle part of the reactor, which leads to overcracking of vapor products, and from there to an increased formation of non-condensable gases, i.e. reduced yield of pyrolytic oil.

Due to the long duration and high cost of traditional pumping tests, the response of well water level to seismic wave, earth tide, and barometric pressure provides a feasible method for determining continuous changes in aquifer hydraulic parameters. Aiming at the problem that the response phase shift of well BB water level to tidal tide M2 is greater than that of tide O1, this paper preferentially calculated the time series changes of S, Be, n and BKu based on the response mechanism of well water level to barometric pressure and earth tide and with the help of smooth moving method. Then by using the mixed flow model, the variation of transmissivity and leakage coefficient over time were simultaneously obtained, and the evolution process and characteristics of aquifer parameters near well BB caused by the Wenchuan earthquake were ultimately discussed. The calculation results are basically consistent with the previous pumping test, and have been verified and compared by using other scholars' methods. This solving process avoids the problems such as excessive dependence on initial values, multiple solutions, and unstable tide O1, which has a promoting effect on the study of the impact of seismic activity on aquifer systems.

Leishmaniasis is the third most common vector-borne disease and a very important protozoan infection. Cutaneous leishmaniasis is one of the most common types of leishmaniasis infectious diseases with up to 2 million occurrences of new cases each year worldwide. A dynamic transmission multivariate time series model was applied to the data to account for overdispersion and evaluate the effects of three environmental layers as well as seasonality in the data. Furthermore, ecological niche modeling was used to investigate the geographical suitable conditions for cutaneous leishmaniasis using temperature, precipitation and altitude as environmental layers, together with the leishmaniasis presence data. A retrospective analysis of the cutaneous leishmaniasis spatial data in Afghanistan between 2003 and 2009 indicates a steady increase from 2003 to 2007, a small decrease in 2008, then another increase in 2009. An upward trend and regularly repeating patterns of highs and lows was observed related to the months of the year which suggests seasonality effect in the data. Two peaks were observed in the disease occurrence-- January to March and September to December -- which coincide with the cold period. Ecological niche modelling indicates that precipitation has the greatest contribution to the potential distribution of leishmaniasis.

The study of precipitation amount at different time scales constitutes an important issue in climate research and risk assessment. When dealing with daily totals, a frequent but sometimes underestimated problem is at what time the observation day begins. The choice of different starting times may lead to incompatibility between stations and incorrect identification of extreme events. In this work, the problem of temporal misalignment between precipitation datasets characterized by different starting time of the observation day is analyzed. The most widely used adjustment methods (1day and uniform shift) and two methods based on reanalysis (NOAA and ERA5) are evaluated in terms of temporal alignment, precipitation statistics and percentile distributions. As test series, the precipitation amount collected from 9 a.m. local time (09 LT) on the previous day to 09 LT on the target day (9-9 datasets) of the Padua and nearby stations in the period 1993-2022 have been selected. Results show that the reanalysis-based methods, in particular ERA5, outperform the others in temporal alignment, regardless the station. But, for the periods in which reanalysis data are not available, “1day” method, which shifts the daily amount back one calendar day, and “unif” method, which distributes uniformly the daily total from a 2-day moving window surrounding the target date, can be considered valid alternatives. On the other side, concerning the precipitation statistics, the reanalysis-based methods are not the best option, as they increase the precipitation frequency and reduce the mean value over wet days, NOAA much more than ERA5. Nevertheless, the uniform method provides a larger deviation from the original daily series. The use of the series of a station nearby the target one, which is mandatory in case of missing data, gives similar or better results than applying any adjustment method to the 9-9 series. General conclusions can hardly be drawn as they depend on the method and station. For the Padua dataset, the analysis was repeated at monthly and seasonal resolution. In general, the adjustment series show the most relevant changes in the precipitation statistics in summer and less temporal alignment with the original series in summer and autumn, the two seasons mainly affected by heavy rains in Padua. Finally, the percentiles distribution, analyzed for all the methods and stations, indicates that any adjustment method underestimates the percentile values, except ERA5. Only Legnaro, the station most correlated with Padua, gives results like ERA5.

Dynamic virtual testing by Hardware in the Loop (HIL) real time simulation systems is common to minimize physical tests to validate and verify control algorithms, logics and software, under normal and emergency conditions. The accurate but costly HIL models setup activities could have an extended use to simulate faulty conditions that are seldom observable in the real system, yet they must be detected in advance and recognized. Data driven diagnostic methods have reached a mature development, in various sectors, proving effective in early detecting slowly varying deviations from nominal patterns of signals, even without a priori knowledge of their nature and behavior. These methods rely on vast amount of data logged from real systems that are ever and ever richer of monitoring telemetries that are worth being exploited. However, due to the usually reliable and safe systems being managed, it is often difficult to collect enough data on anomalous situations to validate fault detection and isolation and limit false positives. HIL model-based simulations allow generating and observing operational domains or transients rarely observed in real operations. This allows identifying the signals that are most correlated to faults and that could be selected to setup data-based diagnostic models of parts or subsystems, which are more suitable than the whole HIL model for online diagnostics, as well as to identify the features and trends that are most symptomatic of anomalous conditions.

The upregulated expression of thyrosine kinase AXL has been reported in several hematologic and solid human tumors including gastric, breast, colorectal, prostate, and ovarian cancers. Thus, AXL can potentially serve as a diagnostic and prognostic biomarker for various cancers. This paper reports the first-ever use of loop-mediated isothermal amplification (LAMP) of the AXL gene as a diagnostic method for ovarian cancer. We demonstrated simple instrumentation toward a point-of-care device to perform LAMP. This paper also reports the first-ever use of core-shell beads as a microreactor to perform LAMP as an attempt to promote environmentally friendly laboratory practices.

The article discusses the results of investigations performed during a thermo-mechanical treatment of forgings made of chromium-molybdenum 42CrMo4 grade steel. The treatment was realized during a regular series production. The forging process was combined with a heat treatment carried out directly after forging on a specially adapted station. Such a production technology will make it possible to eliminate the step of repeated heating of the forgings. On the example of an element of a steering gear, it was demonstrated how it is possible to perform an isothermal annealing process starting from the temperature at which the trimming of the forgings ends. During the cooling of the forgings, it is enough to maintain the temperature at the proper level in order for the exothermal phase transformation of austenite into pearlite to take place. With an appropriate design of the processing line, the heat released during the transformation could be used to maintain the applied temperature, thus limiting the consumption of energy needed to power the devices. The test results show that, with the properly selected temperature of isothermal annealing, it is possible to obtain an equilibrial ferritic-pearlitic structure in the required hardness scope. Introducing such a solution into the industrial practice would allow significant savings of the energy used for the heat treatment.

The current coronavirus disease 2019 (COVID-19) pandemic is largely driven by community transmission, after 2019 novel Coronavirus (2019-nCoV or SARS-CoV-2) crosses the borders. To stop the spread, rapid testing is required at community clinics and hospitals. These rapid tests should be comparable with the standard PCR technology. Isothermal amplification technology provides an excellent alternative that is highly amenable to resource limited settings, where expertise and infrastructure to support PCR are not available. In this review, we provide a brief description of isothermal amplification technology, its potential and the gaps that need to be considered for SARS-CoV-2 detection. Among this emerging technology, loop mediated amplification (LAMP) and recombinase polymerase amplification (RPA) technologies have been identified as potential platforms that could be implemented at community level, without samples referral to a centralised laboratory and prolonged turn-around-time associated with the standard COVID-19 RT-PCR test. LAMP, for example, has recently been shown to be comparable with PCR and could be performed in less than 30 min by non-laboratory staff, without RNA extractions commonly associated with PCR. More so, it is cost effective and could easily be scaled up to resource limited settings. Diagnostics developers, scientific community and commercial companies could consider this alternative method to help stop the spread of COVID-19.

Increasing utilization of secondary raw materials and alternative fuels results in increasing contents of metals in cements. One of elements, the content of which keeps rising in cement is zinc. It comes to cement with secondary raw materials such as slag or fly ash or by the utilization of used tires as an alternative fuel. Zinc ions significantly prolong the hydration process in cement. This work deals with the influence of zinc ions in the form of very poorly soluble ZnO salt and easily soluble ZnCl2 and Zn(NO)3 on the hydration of cement blended with fly ash. Zinc was dosed in the range of 0.05, 0.1, 0.5 a 1% of cement weight. Final products were next analyzed using X-Ray Diffraction.

This paper studies the duration patterns of unemployment spells for immigrants and the determinants of unemployment’s completion into one of a number of studied labour market states in Finland. We estimate a duration model for unemployment with competing risks of its terminating into employment, labour market training or economic inactivity. Taking into account the wide period of observation and opportunities to analyse processes of labour market integration during various periods of economic development in Finland, in combination with the individualistic character of the labour careers of immigrants, this research is beneficial owing to the many various findings concerning labour market integration of immigrants. The approach undertaken in this research has a dualistic “descriptive-dynamic” character under which integration is understood as a never-ending process, which is conditioned by a time period of long-term existence and a context of solitary action. We find that transitions out of unemployment spells have a cyclical character; after every new “cycle” in unemployment, the probability of terminating unemployment decreases further. We also find that ascriptive factors make sense in the process of job-placement of immigrants from unemployment. Therefore, the gender, education and age of immigrants, as well as the effect of the period in which first unemployment occurred, potentially predict transitions out of unemployment and further labour market integration of immigrants.

The allosteric SERCA (Sarcoplasmic/Endoplasmic Reticulum Ca2+-ATPase) activator CDN1163 has been recently added to the group of pharmacological tools for probing SERCA function. We chose to investigate the effects of the compound on T lymphocyte Ca2+ stores, using the well-described Jurkat T lymphocyte as a reliable cell system for Ca2+ signaling pathways. Our study identified the lowest concentrations of the SERCA inhibitors thapsigargin (TG) and 2,5-di-(tert butyl)-1,4-benzohydroquinone (tBHQ) capable of releasing Ca2+, permitting the differentiation of the TG-sensitive SERCA 2b Ca2+ store from the tBHQ-sensitive SERCA 3 Ca2+ store. We proceeded to test the effects of CDN1163 on Ca2+ stores, examining specific actions on the SERCA 2b and SERCA 3 Ca2+ pools using our low dose SERCA blocker regimen. In contrast to previous work, we find CDN1163 exerts complex time-sensitive and SERCA isoform-specific actions on Ca2+ stores. Surprisingly, short-term exposure (0-30 minutes) to CDN1163 perturbs T cell Ca2+ stores by suppressing Ca2+ uptake with diminished Ca2+ release from the SERCA 2b-controlled store. Concomitantly, we find evidence for a SERCA-activating effect of CDN1163 on the SERCA 3 regulated store, given the observation of increased Ca2+ release inducible by low dose tBHQ. Intriguingly, longer-term (&gt;12 hours) CDN1163 exposure reversed this pattern, with increased Ca2+ release from SERCA 2b-regulated pools, yet decreased Ca2+ release responses from tBHQ-sensitive SERCA 3 pool. Our results reveal differential effects of CDN1163 on Ca2+ stores regulated by distinct SERCA isoforms, prompting the need for careful interpretation of the compound’s effects, particularly in cells expressing multiple SERCA isoforms.

The aim of this study is to analyze the characteristics of drought such as intensity, cumulative curves and trends, based on SPEI (Standardized Precipitation Evapotranspiration Index) at 8 stations in Korea from 1981 to 2010. The traditional SPEI is based on Thornthwaite equation for estimating evapotranspiration; SPEI_th. However, a standard of agricultural water management in Korea suggests FAO Penman-Monteith equation; SPEI_pm. In this study, we analyzed the intensity and trends of drought using SPEI_th and SPEI_pm, respectively, and analyzed the relationship between them. Both of central and southern region, the SPEIs were below -1.0 (moderated drought) for the periods May-August in the representative drought year such as 1988, 2001, and 2008-09. The frequency of drought was higher in southern region than central region. In addition, SPEI_pm showed slightly more intensive drought rather than SPEI_th except for Chuncheon and Gwangju. In 5 stations except for Cheoncheon, Gwangju and Jinju, the cumulative probability that SPEI_pm is below -1.5 was significantly increased from 1981-1995 to 1996-2010. As the results of drought trends, the increasing trend of SPEIs was shown on fall season, and the cumulative probability that SPEI_pm is below -1.5 was also significantly increased.

Novolac phenol-formaldehyde resins have gained extensive commercial utilization across diverse applications due to their exceptional mechanical, thermal, and chemical resistance properties. In this investigation, we successfully synthesized a traditional novolac, and a biobased novolac phenol-formaldehyde resin by partially substituting phenol with a bio-oil obtained from the organic phase resulting from the fast pyrolysis of pinewood biomass. Despite extensive investigations into the curing behavior of novolac resins crosslinked with hexamethylenetetramine (HMTA) through numerous model-fitting cure kinetic studies, a comprehensive model for predicting the crosslinking of bio-based phenol-formaldehyde resins in the presence of HMTA has not yet been studied. The primary objective of this research was to compare and apply several commonly used kinetic models to predict the degree of curing and cure rate of the synthesized resins, using DSC dynamic measurements. Our results demonstrated that the autocatalytic model exhibited excellent fitting for the traditional novolac resin and HMTA mixture, while the Kamal model showed better fitting with the experimental data obtained for the bio-based phenol-formaldehyde resin and HMTA system. In addition, the results evidenced a significant drop in the curing temperature by partially replacing phenol with bio-oil. Additionally, the results revealed a notable reduction in curing temperature when phenol was partially substituted with bio-oil. This substitution not only offers environmental benefits but also promotes energy efficiency and enhances production safety. The data collected in this study is pivotal for our subsequent research endeavors, which aim to develop environmentally sustainable materials optimized for use in 3D printing manufacturing processes.

The availability of simple SARS-CoV-2 detection methods is crucial to contain the COVID-19 pandemic. This study examined whether a commercial LAMP assay can reliably detect SARS-CoV-2 genomes directly in respiratory samples without having to extract nucleic acids (NA) beforehand. Nasopharyngeal swabs (NPS, n = 220) were tested by real-time reverse transcription (RT)-PCR and with the LAMP assay. For RT-PCR, NA were investigated. For LAMP, NA from 26 NPS in viral transport medium (VTM) were tested. The other 194 NPS were analyzed directly without prior NA extraction [140 samples in VTM; 54 dry swab samples stirred in phosphate buffered saline]. Ten NPS were tested directly by LAMP using a sous-vide cooking unit. The isothermal assay demonstrated excellent specificity (100%) but moderate sensitivity (68.8%), with a positive predictive value of 1 and a negative predictive value of 0.65 for direct testing of NPS in VTM. The use of dry swabs, even without NA extraction, improved the analytical sensitivity; up to 6% of samples showed signs of inhibition. The LAMP could be performed successfully with a sous-vide cooking unit. This technique is very fast, requires little laboratory resources and can replace rapid antigen tests or verify reactive rapid tests on site.

The wavelet spectral characteristics of three respiratory muscle signals (Scalenus (SC), Parasternal intercostal (IC) and Rectus abdominis (RA)) and one locomotor muscle Brachioradialis (BR) were analyzed in the time-frequency (T-F) domain during breath-holding (BH). Study was performed for an end-expiratory BH maneuver on twelve healthy, physically active, naive apneists (6 professional athletes; 6 recreational athletes, two in the post-COVID-19 period) using surface electromyography (sEMG). We observe individual effects dependent on muscle oxygenation and person’s fitness, consistent with the mechanism of motor unit (MU) recruitment and the transition of slow-twitch oxidative (type 1) to fast-twitch (oxidative) glycolytic (type 2) muscle fibers. Professional athletes had longer BH duration (BHD) and strong hypercapnic response on expiratory RA, which is activated abruptly at higher BHDs in a person-specific range below 250 Hz and dependent on BHD. This is in contrast with recreational athletes, who had strong hypoxic response on inspiratory IC, which is activated faster and gradually in the frequency range of 250-450 Hz (independent of the apneist and BHD). This pilot study preliminarily indicates that it is possible to non-invasively assess the physiological characteristics of skeletal muscles, especially oxygenation, and improve physical fitness tests by determining T-F features of elevated myoelectric IC and RA activity during BH.

How to build an optimal model where three terms “time, causality, and entropy” will be interrelated in a most correct way? This task has a semantic and physical aspect. We give in this article the solution that is based only on elementary perception. In physics, we experience time with our senses as the duration of material change running in space. This fact is the standpoint for our model where causality is only a principle, it is not a physical actuality and entropy runs only in space and not in time. Time is merely a duration of entropy increasing and is entering existence when measured by the observer.

Noninvasive brain stimulation technique can be used for modulation of motor behaviors such as reaction time (RT). The main aim of this study was to investigate whether RT during a sequential visual isometric pinch task (SVIPT) can be affected by anodal transcranial direct current stimulation (a-tDCS) over three different stimulation sites such as dorsolateral prefrontal cortex (DLPFC), primary motor cortex (M1) or posterior parietal cortex (PPC). We also aimed to assess if stimulation of these cortical sites affect the transfer of learning during SVIPT. A total of 48 right-handed healthy participants were randomly assigned to one of the four a-tDCS groups: 1) left M1, 2) left DLPFC, 3) left PPC and 4) sham. A-tDCS was applied concurrent with SVIPT in which the participants were precisely controlled their forces to reach seven different target forces from 10 to 40% of maximum voluntary contraction (MVC) presenting on a computer screen with right dominant hand. Four test blocks were randomly performed at baseline and 15 min after the intervention including sequence and random blocks with either hand. Our results showed significant differences between a-tDCS groups on ratio RT in the sequence blocks of both the right trained (P = .041) and left untrained hands (P = .023) for target forces of 15% and 30 % of MVC, respectively. In sequence blocks, M1 showed significant elongation in ratio RT for the target force of 15% and 30 % MVC compared to PPC and Sham groups in the right hand. In sequence blocks with left hand, this negative effect were found between M1-DLPFC and M1-Sham groups. In random blocks, no significant differences were found among four groups at each target forces for the left hand while there were significant differences for 15% (P =. 04) and 40% MVC (P =. 035) in the right hand. Our findings suggest that three different stimulation sites (DLPFC, M1 or PPC) were differentially affected by a single session of a-tDCS at some target forces during SVIPT. The effects of a-tDCS on ratio RT were transferred in the left untrained hand for sequence blocks but not random blocks. Further research is needed to understand fundamental aspects of these main areas of the brain on temporal processing in a precision control task such as SVIPT.

A model of space-time is presented, whose origin is set before the appearance of any universe. It uses concepts of previous work, a central one being that the information about the laws of nature is stored locally everywhere in space such that all physical processes obey them. Since information storage is bound to matter or energy, space is assumed to consist of dark energy (DE), which thus assumes an importance far beyond its function as a stopgap for an energy deficit in our universe ( U ). The primordial state (PS) is a timeless and relatively large space of 3 dimensions described by a Wheeler DeWitt (WDW) equation, whose solution is interpreted as an arrangement of very many space quanta and possesses properties that remind of the time-honored concept of the unmoved mover. The comparison of WDW solutions belonging to different mass densities of the DE favors one in which the space quanta are mini black holes. This allows the space quanta to be imagined as mass points which are kept at a distance compatible with the quantum volume by the Pauli principle or something equivalent. Triggered by a dramatic increase in probability, the PS is followed by a time-controlled sequence of quantized expansion states (ES i ). The concomitant emergence of time occurs in a lightning huge crash, consuming almost all DE of the PS. The subsequent quantized ES i emerge from a WDW equation, novelly derived from a solution of the modified cosmic momentum equation, which classically describes an exponential space expansion (CS). The huge volme of the ES i is also used as size of the PS. Information is assumed to be geometrically stored in arrangements of space quanta similar to how genetic information is stored in DNA molecules. During the CS information must be transferred from already existing "information quanta" to new ones. This requires time, slows down the expansion and is taken into account by a friction term in the cosmological momentum equation thus modified. Since the Friedmann-Lemaître (FL) equation remains fully valid, the model is widely based on recognized equations, so that some results may be understood as interpretations.

Schistosoma infection in snails can be monitored by microscopy or indirectly by sentinel mice. As both these approaches sometimes miss infections, more sensitive tests are needed, particularly in low-level transmission settings. In this study, the loop-mediated isothermal amplification (LAMP) technique, designed to detect a specific 28S ribosomal S. japonicum gene with high sensitivity, was compared to microscopy using snail samples from 51 areas endemic for schistosomiasis in five Chinese provinces. The results were compared with those by polymerase chain reaction (PCR) adding DNA sequencing as a reference when needed. The testing of pooled snail samples showed that a dilution factor of 1/50, i.e., one infected snail plus 49 non-infected ones, would still result in a positive reaction after the recommended number of amplification cycles. Testing a total of 232 pooled samples, emanating from 4,006 snail specimens, with the LAMP assay showed a 6.5% rate of infection, while traditional microscopy found only 0.04% positive samples in the same materials. Parallel PCR analysis confirmed the diagnostic accuracy of the LAMP assay, with DNA sequencing even giving LAMP a slight lead. Microscopy and the LAMP test were carried out at local schistosomiasis-control stations demonstrating that the potential of the latter assay to serve as a point-of-care (POC) test with results available within 60–90 minutes, while the more complicated PCR test had to be carried out at the National Institute of Parasitic Diseases (NIPD) in Shanghai, China. In conclusion, LAMP was found to be clearly superior to microscopy and as good as, or better, than PCR. Application of LAMP testing would be useful for surveillance and risk prediction as it requires less time than other techniques and can be used under field conditions, which improves and accelerates schistosomiasis control.

Considered is “time as an interval” including time from the past and from the future, in contrast to time as a moment. Equilibrium as the basis for a description of changing properties in physics is understood to depend on the “mean velocity theorem”, while a “time” of equilibrium resembles a center of weight. This turns out to be a good method to derive properties for any function of time t including space coordinates q(t) and expressions for the time dependent Hamiltonian. Introduced are derivatives depending on time intervals instead of time moments and with these a new relation between the Lagrangian L and the Hamiltonian H. As an application introduced is a step by step method to integrate stationary state “local” time interval measurements to beyond “locality” in General Relativity. Because of limits on the measures of the resulting time intervals and their asymmetry, this allows for a probabilistic interpretation of quantities that have these intervals as time domain in QM. Their asymmetry also questions the time reversal symmetry of GR. Another application of time intervals is the discussion of the measurement of starlight radiation energy and QM wave packet collapse as an example of a time dependent Hamiltonian. Finally a relation between starlight frequency, metric and space- and time intervals is found. Discussed is how finite and asymmetric time intervals correspond to time dependent H and symmetric infinite time intervals to a time independent H. From there, in cosmological perspective, finite time intervals can help to describe how entropy change could relate to dark energy.

In this research, we investigate the bending of photon light and/or time-like geodesics within the context of four-dimensional space-time geometry, specifically in the presence of topological defects. These topological defects manifest as cosmic string space-time configurations, encompassing screw dislocation, spiral dislocation, and spacelike dislocation. Our primary objective is to determine the extent of deflection experienced by light-like and time-like geodesics and analyze how this deflection is affected by the cosmic string parameter, screw dislocation parameter, and spacelike dislocation parameter. To accomplish this, we employ a derivation technique that centers on the observation that photon rays (light-like geodesics) and/or time-like geodesics follow paths parallel to the z-axis while maintaining a constant radius along the cylinder.

This addendum contains clarifications and a sharpening of some of the results on the VIT transform framework developed in [1]. The focus is on the right-coefficient and left- coefficient forms of the transform, the extraction of a first-order term from a left polynomial fraction, and the application to linear time-varying systems.

In this paper, the nanoscale dissipative mechanisms of a Cu pad in a Ball Grid Array (BGA) packaging structure during isothermal ageing and uniaxial tension were investigated by the molecular dynamics (MD) method and experiments. From the result of the isothermal ageing test, a nonuniform consumption of Cu and large amount of Kirkendall voids were observed at the interface of Cu and Cu₃Sn. To study the effect of pressure and orientation on this phenomenon, MD simulations were conducted on four types of Cu-Cu₃Sn interface structures with different orientations of Cu. By comparing the diffusion coefficients of atoms in those cases, it was found that the tensile stress would inhibit the diffusion of atoms, whereas compressive stress would accelerate it, and this would be more significant under a larger magnitude of stress and temperature. Note that, in the model with the (101) surface Cu at the interface, both Cu and Cu₃Sn have a higher diffusion coefficient compared with the model with (001) surface Cu. Thus, the orientation of Cu will also contribute to the uniform consumption of the pad. Uniaxial tension simulation combined with DXA and CSP analyses on those models also shows the model with (001) surface Cu has a greater mechanical reliability in our simulations and related experiments.

Background: The electroretinogram is a clinical test used to assess the function of the photoreceptors and retinal circuits of various cells in the eye, with the recorded waveform being the result of the summated response of neural generators across the retina. Methods: The present investigation involved an analysis of the electroretinogram waveform in both the time and time-frequency domain through the utilization of the discrete wavelet transform and continuous wavelet transform techniques. The primary aim of this study was to monitor and evaluate the effects of treatment in a New Zealand rabbit model of endophthalmitis via electroretinogram waveform analysis and to compare these with normal human electroretinograms Results: The wavelet scalograms were analyzed using various mother wavelets, including the Daubechies, Ricker, Wavelet Biorthogonal 3.1 (bior3.1), Morlet, Haar, and Gaussian wavelets. Distinctive variances were identified in the wavelet scalograms between rabbit and human electroretinograms. The wavelet scalograms in the rabbit model of endophthalmitis showed recovery with treatment in parallel with the time -domain features. Conclusions: The study compared Adult, Child, and Rabbit electroretinogram responses using DWT and CWT, finding that Adult signals had higher power than Child signals, and Rabbit signals showed differences in a-wave and b-wave depending on the type of response tested, while Haar Wavelet was found to be superior in visualizing frequency components in electrophysiological signals in following the treatment of endophthalmitis and may give additional outcome measures for the management of retinal disease.

Efficient use of the operating room (OR) is crucial for any hospital. One of the major inefficiencies in the OR is surgical cases not starting or finishing on time as scheduled. When a case is delayed, it affects all subsequent cases in that OR. This study uses discrete choice analysis to determine the significant factors, including team familiarity, that influence OR case on-time start and finish. A case is considered on-time if the documented procedure start and finish times are no more than 10 minutes after the scheduled start and finish times. The analysis uses surgical case data from a large tertiary referral hospital and academic center in Greenville, South Carolina. The case data includes all surgical cases (15,091) performed during regular workdays in 2013. Two binary logit models are developed: one for case on-time start and one for case on-time finish. Results indicate that higher team familiarity between surgeon and anesthesiologist, surgeon and circulating nurse, surgeon and scrub nurse, and surgeon and CRNA improve the likelihood of an OR case on-time start and on-time finish. This finding indicates that the OR scheduling staff in the study hospital make a concerted effort to schedule the surgical teams with members who have worked well together in the past.

The present work is a numerical simulation of velocity and mixture fraction fields in a turbulent non-reaction Propane jet flow issuing into parallel co-flowing air, in isothermal condition which has been experimentally described here: http://www.sandia.gov/TNF/DataArch/ProJet.html. The objective is a better understanding of the flow structure and mixing process, a situation in which there is no chemical interaction and heat-transfer. The two-equation Realizable k-ε eddy viscosity turbulence model has been used to simulate the turbulent flow field on a 2D plane (i.e., on a 5-degree sector of the experimental domain), because Realizable k-ε more accurately predicts the spreading rate of both planar and round jets and presents the best proficiency in comparison with all versions of the k-ε models. Afterward, axial and radial profiles of mean velocities, turbulence energy, mean mixture fraction, the mixture fraction half radius (Lf), and the mass flux diagram have been numerically elicited for grid independent mesh (mesh B) and compared with corresponding experimental data to assess the numerical model. To obtain turbulence kinetic energy, k, due to lack of w' in the experimental data, the assumption of w'=v' seems to be valid. Simulations have demonstrated that mean mixture fraction (at radial profiles at locations x/D=0, 4, 15, 30 and 50) and its half radius, Lf, which characterizes jet width expanse, are prominently well-captured; Moreover, mean vertical velocity fields (in X-direction: Umean) have revealed less accuracy but still conspicuously well-captured. However, mean vertical velocity fields (in Y-direction: Vmean) have disclosed less resolution; Likewise, turbulence kinetic energy, k, have manifested moderate accuracy (between Umean and Vmean). It should be noticed that although numerical results for absolute pressure, p, have been obtained on aforementioned sections, there were no experimental data to compare with them. Thus, the corresponding numerical data has not been demonstrated in this study.

Time estimation was investigated in 24 healthy adults, 12 women and 12 men, before and after an exhaustive exercise. We compared the capability of estimating time intervals in the range from 1 to 5 s using tasks requiring mental count and tasks that did not allow the mental count. Time estimation and blood lactate levels were evaluated before and at the end of the exercise. We found that the perception of time intervals between 1 and 5 s was affected at the end of the exercise. The observed effects, associated with a significant increase in blood lactate levels, were different in the two types of time estimation used in the present study. In experimental conditions in which participants had to evaluate duration of the time interval by mental counting, at the end of exercise a significant reduction in the overestimation of time made at rest was observed. On the other hand, when participants had to assess the difference in duration between two events without the possibility to mentally count, at the end of the exercise a significant deterioration in performance was observed. In both cases, no gender differences were seen.

This article begins with exploring fundamental limits in the universe. It examines key principles, such as the uniformity of physical laws and Energy conservation, that lead to the principles of maximum speed, locality, and maximum density. These universal limits govern physical phenomena, culminating in very interesting results.They led to the exploration of Quantum black holes. Quantum black holes are relativistically revolving miniature charged black holes consisting of a single core at the highest possible density. They are the only structures small enough to keep all charges quantized (including gravitational charges). I then demonstrated that quarks and leptons comprise smaller entities - the Quantum Black Holes. Exploring these elementary particles reveals that they release their Energy outward, altering the curvature of nearby space-time and providing new insights. We can characterize movements and processes in local space-time with four sets of equations representing the four charge types and one set representing Dark Matter. By the end of the article, I prove that Quantum black holes explain the quantization of gravity, the nature of Luminous and dark Matter, the Mass, size, and (quantized) charges quantities of elementary particles and the nature of neutrino oscillations.

The Thermocontextual Interpretation (TCI) is proposed here as an alternative to existing interpretations of physical states and time. Prevailing interpretations are based on assumptions rooted in classical mechanics. Logical implications include the determinism and reversibility of change, and an immediate conflict. Determinism underlies causality, but causality implies a distinction between cause and effect and an arrow of time, conflicting with reversibility. Prevailing interpretations also fail to explain the empirical irreversibility of wavefunction collapse without untestable and untenable metaphysical implications. They fail to reconcile nonlocality and relativity without invoking superdeterminism or unexplained superluminal correlations. The Thermocontextual Interpretation defines a system’s state with respect to its actual surroundings at a positive ambient temperature. The TCI bridges existing physical interpretations and thermodynamics as special cases, which define states either with respect to an absolute-zero reference or with respect to a thermally equilibrated reference. The TCI defines system time as a complex property of state spanning both reversible mechanical time and irreversible thermodynamic time, and it distinguishes between system time and the reference time of relativity and causality, as measured by an observer’s clock. And, the TCI provides a physical explanation for nonlocality, consistent with relativity, without hidden variables, superdeterminism, or “spooky action.”

The prevailing interpretations of physics are based on deeply entrenched assumptions, rooted in classical mechanics. Logical implications include: the denial of entropy as a fundamental physical property, and the inability to explain irreversible change, random quantum measurements, or nonlocality without untestable and implausible metaphysical implications. We propose a conceptual model that is based on empirically justifiable assumptions and consistent with observations. The WYSIWYG Conceptual Model (WCM) assumes no hidden properties: “What You can See Is What You Get.” The WCM contextually defines a system’s state with respect to its actual ambient background, and it extends existing models of physical reality by defining entropy and exergy as objective contextual properties of state. The WCM establishes the irreversible dissipation of exergy and the Second law of thermodynamics as a fundamental law of physics, it recognizes physical randomness, and it provides a physical explanation for nonlocality, consistent with Special Relativity, without hidden variables, superdeterminism, or “spooky action.”

An initial-boundary value problem is considered for one-dimensional isothermal equations of the dynamics of viscous compressible multicomponent media, which are a generalization of the Navier--Stokes equations. We prove the stabilization of the solution to the initial-boundary value problem while the time tends to infinity, without simplifying assumptions for the structure of the viscosity matrix, except for the standard physical requirements of symmetry and positive definitenes.

This paper presents three types of sliding mode controllers for a magnetic levitation system. First, a proportional-integral sliding mode controller (PI-SMC) is designed using a new switching surface and a proportional plus power rate reaching law. The PI-SMC is more robust than a feedback linearization controller in the presence of mismatched uncertainties and outperforms the SMC schemes reported recently in the literature in terms of the convergence rate and settling time. Next, to reduce the chattering phenomenon in the PI-SMC, a state feedback-based discrete-time SMC algorithm is developed. However, the disturbance rejection ability is compromised to some extent. Furthermore, to improve the robustness without compromising the chattering reduction benefits of the discrete-time SMC, mismatched uncertainties like sensor noise and track input disturbance are incorporated in a robust discrete-time SMC design using multirate output feedback (MROF). With this technique, it is possible to realize the effect of a full-state feedback controller without incurring the complexity of a dynamic controller or an additional discrete-time observer. Also, the MROF-based discrete-time SMC strategy can stabilize the magnetic levitation system with excellent dynamic and steady-state performance with superior robustness in the presence of mismatched uncertainties. The stability of the closed-loop system under the proposed controllers is proved by using the Lyapunov stability theory. The simulation results and analytical comparisons demonstrate the effectiveness and robustness of the proposed control schemes.

The possibility to test a radio frequency transceiver through the use of appropriate channel emulators allows to evaluate their performance under various operating conditions. Many systems are able to operate with a relatively limited instantaneous bandwidth by applying known statistical models. Sometimes it is necessary to evaluate the performance of a RF transceiver installed on high or very high speed platforms over predictable trajectories using optionally DEMs (Digital Elevation Models)data of the terrain to estimate the number of stimulated paths and their contributions during the flight. When the instantaneous bandwidth of the signal becomes high (over several hundred of MHz), one of the most important phenomenon to consider is the Doppler spread induced by the channel and traditional narrowband models become unuseful. In this paper there are presented some results when a time expansion is adopted in order to emulate the transceiver dynamic and the consequent Doppler spread with the aim to control the spectral purity of the emulated propagation channel.

The continuous nature of space and time is a fundamental tenet of many scientific endeavours. That digital representation imposes granularity is well recognized but whether it is possible to address space completely remains unanswered. Part 1 argues that Hales’ proof of Keppler’s conjecture on the packing of hard spheres suggests the answer to be ‘no’, providing examples of why this matters in GIS generally and spatio-temporal GIS in particular. Part 2 seeks to resolve the dichotomy between continuous and granular space, showing how a continuous space may be emergent over a random graph. However, its projection into 3D/4D imposes granularity. Perhaps surprisingly, representing space and time as locally conjugate may be key to addressing a ‘smooth’ spatial continuum. This insight leads to the suggestion of Face Centered Cubic Packing as a space-time topology but also raises further questions for spatio-temporal representation.

Multicellular life evolved from simple unicellular organisms that could replicate indefinitely being essentially ageless. At this point, life split into 2 fundamentally different cell types: the immortal germline representing an unbroken lineage of cell division with no intrinsic endpoint and the mortal soma which ages and dies. In this review, we describe the germline as clock-free and the soma as clock-bound and discuss aging with respect to 3 DNA-based cellular clocks (telomeric, DNA methylation, and transposable element). The ticking of these clocks corresponds to the stepwise progressive limitation of growth and regeneration of somatic cells that we term, somatic restriction. Somatic restriction acts in opposition to strategies that ensure continued germline replication and regeneration. We thus consider the plasticity of aging as a process not fixed to the pace of chronological time but one that can speed up or slow down depending on the rate of intrinsic cellular clocks. We further describe how germline factor reprogramming might be used to slow the rate of aging and potentially reverse it by causing the clocks to tick backwards. Therefore, reprogramming may eventually lead to therapeutic strategies to treat degenerative diseases by altering aging itself, the one condition common to us all.

The stock beta coefficient literature extensively discusses the proper methods for the estimation of beta as well as its use in asset valuation. However, there are relatively few references with respect to the appropriate time horizon that investors should utilize when evaluating the risk-return relationship of a stock. We examine the appropriate time horizon for beta estimation differentiating our results by sector according to the Industry Classification Benchmark. We employ data from the NYSE and we estimate varying lengths of beta employing data from 30 to 250 trading days. The constructed beta series is then examined for the presence of breaks using the endogenous structural break literature. Results show evidence against the use of betas that employ more than 90 trading days of data provisional to the sector under study.

This paper examines the effect of chronotype on the delinquent credit card payments and stock market participation through preference channels. Using an online survey of 455 individuals who have been working for 3 to 8 years in companies in mainland China, the results reveal that morningness is negatively associated with delinquent credit card payments. Morningness also indirectly predicts delinquent credit card payments through time preference, but this relationship only exists when individuals’ monthly income is at low and average level. On the other hand, financial risk preference accounts for the effect of morningness on stock market participation. Consequently, an additional finding is that morningness is positively associated with financial risk preference, which contradicts previous finding in the literature. Finally, based on the empirical evidence, we discuss the plausible mechanisms that may drive these relationships and the implications for theory and practice. The current study contributes to the literature by examining the links between circadian typology and particular financial behaviours of experienced workers.