The research object was the stress-strain state of shear stud bonds in the contact joint of steel-concrete beams. The work diagrams for three types of anchors are given. Based on the analysis of numerical and full-scale experiments, analytical dependencies are proposed that reflect the actual operation of anchor ties. Comparisons of the calculation results by analytical formulas and comparisons with numerical and full-scale experiment data are given. Numerical studies have revealed the pattern of the stress-strain state of the contact joint, the stages of development of cracks in the concrete flange, and the sequence of development of deformations in anchor ties. It was revealed that vertical shear studs bonds have an increased bearing capacity, although displacements are 1.5-2 times greater than those of loop-shaped anchor ties.

Pipeline conflicts arising from data dependencies are a common issue encountered in the hardware implementation of layered QC-LDPC decoders. This paper proposes an efficient layered decoding architecture to reduce pipeline conflicts without introducing stall cycles, by reordering the processing order offline and using the patch method based on variable-to-check message. The experimental results on the LDPC code of the IEEE802.16 standard in the OFDM-PON system demonstrate that the proposed architecture has a sensitivity improvement of 0.125 dBm and 0.375 dBm, respectively, compared with our previous work and the method described in the other work.

A low-cost bio-mass-derived carbon substrate has been employed to synthesize MoS₂@carbon composites through a hydrothermal method. Carbon fibers derived from natural cotton provide a three-dimensional and open framework for the uniform growth of MoS₂ nanosheets, thus constructing hierarchically coaxial architecture. The unique structure could synergistically benefit fast Li-ion and electron transport from the conductive carbon scaffold and porous MoS₂ nanostructures. As a result, the MoS₂@carbon composites, when served as anodes for Li-ion batteries, exhibit a high reversible specific capacity of 820 mAh g^-1, high-rate capability (457 mAh g^-1 at 2 A g^-1), and excellent cycling stability. The superior electrochemical performance makes the MoS₂@carbon composites to be low-cost and promising anode materials for Li-ion batteries.

For shear-critical structural elements where the use of stirrups is not desirable, such as slabs or beams with reinforcement congestion, steel fibers can be used as shear reinforcement. The contribution of the steel fibers to the shear capacity lies in the action of the steel fibers bridging the shear crack, which increases the shear capacity and prevents a brittle failure mode. This study evaluates the effect of the amount of fibers in a concrete mix on the shear capacity of steel fiber reinforced concrete beams with mild steel tension reinforcement and without stirrups. For this purpose, twelve beams were tested. Five different fiber volume fractions were studied: 0.0%, 0.3%, 0.6%, 0.9%, and 1.2%. For each different steel fiber concrete mix, the concrete compressive strength was determined on cylinders and the tensile strength was determined in a flexural test on beam specimens. Additionally, the influence of fibers on the shear capacity is analyzed based on results reported in the literature, as well as based on the expressions derived for estimating the shear capacity of steel fiber reinforced concrete beams. The outcome of these experiments is that a fiber percentage of 1.2% or fiber factor of 0.96 can be used to replace minimum stirrups according to ACI 318-14 and a 0.6% fiber volume fraction or fiber factor of 0.48 to replace minimum stirrups according to Eurocode 2. A fiber percentage of 1.2% or fiber factor of 0.96 was observed to change the failure mode from shear failure to flexural failure. The results of this presented study support the inclusion of provisions for steel fiber reinforced concrete in building codes and provides recommendations for inclusion in ACI 318-14 and Eurocode 2, so that a wider adoption of steel fiber reinforced concrete can be achieved in the construction industry.

This paper aims to investigate the feasibility of strengthening the web opening in the shear zone of RC beams by using iron-based shape memory alloy (Fe-SMA) bars. To conduct this study, numerical analysis with ABAQUS software was employed. The research was divided into six groups of beams with web openings of different lengths (150, 300, and 450 mm), prestressing levels (0%, 30% and 60%), and reinforcement diameters (14, 18, and 22 mm) of Fe-SMA bars. The results show that the presence of web openings can cause a significant reduction in the cracking and ultimate loads of the beams, with reductions ranging from 11 to 50% and 36 to 48%, respectively. However, by adding pre-stressed Fe-SMA bars around small web openings (100×150 mm), the shear capacity of the beam is restored, and the beam exhibits behavior similar to solid beams. Additionally, activating the Fe-SMA bars by 30 and 60% resulted in almost similar cracking loads but improved load-carrying capacity of the beam with small openings by 12% and 9%, respectively, compared to the solid beam. The technique proposed for enhancing shear strength is most effective for beams with small (100×150 mm) and medium (100×300 mm) web openings as it can restore both the beam’s shear strength and stiffness. However, for beams with larger web openings (100×450 mm), the use of activated Fe-SMA beams can recover almost 90% of the solid beam's shear capacity. Furthermore, reinforcing small openings with Fe-SMA bars of different diameters enhances beam shear capacity and stiffness, while for larger openings, higher Fe-SMA reinforcement ratios could potentially restore the beam's full strength and stiffness. This study emphasizes the importance of strengthening web openings in RC beams, particularly in shear zones, and provides significant insights into how to strengthen beams with web openings, thereby contributing to developing safer structures. However, further laboratory experiments are recommended to validate, complement and extend the findings of this numerical study.

Three-dimensional V₂O₅ hollow structures have been prepared through a simple synthesis strategy combining solvothermal treatment and a subsequent thermal annealing. The V₂O₅ materials are composed of microspheres 2–3 μm in diameter and with a distinct hollow interior. The as-synthesized V₂O₅ hollow microspheres, when evaluated as a cathode material for lithium-ion batteries, can deliver a specific capacity as high as 273 mAh·g⁻¹ at 0.2 C. Benefiting from the hollow structures that afford fast electrolyte transport and volume accommodation, the V₂O₅ cathode also exhibits a superior rate capability and excellent cycling stability. The good Li-ion storage performance demonstrates the great potential of this unique V₂O₅ hollow material as a high-performance cathode for lithium-ion batteries.

Chronic joint inflammatory disorders such as osteoarthritis and rheumatoid arthritis have in common an upsurge of inflammation, and oxidative stress, resulting in progressive histological alterations and disabling symptoms. Currently used conventional medication (ranging from pain-killers to biological agents) is potent, but frequently associated with serious, even life-threatening side effects. Used for millennia in traditional herbalism, medicinal plants are a promising alternative, with lower rate of adverse events and an efficiency frequently comparable with that of conventional drugs. Nevertheless, their mechanism of action is in many cases elusive and/or uncertain. Even many of them have been proved effective in studies done in vitro or on animal models, there is a scarcity of human clinical evidence. The purpose of this review is to summarise the available scientific information on these joint-friendly medicinal plants, which have been already tested in human studies: Arnica montana, Boswelliaspp., Curcuma spp., Equisetum arvense, Harpagophytumprocumbens, Salix spp., Sesamumindicum, Symphytumofficinalis, Zingiberofficinalis, Panaxnotoginseng, Whitaniasomnifera.

The calculation of the global shear capacity of steel-concrete composite downstand cellular beams with precast hollow-core units is important as it affects the span to depth ratios and the amount of material used, hence affects the embodied CO2 calculation when designers are deciding on the floor grids. This paper presents a reliable tool that can be used by designers to alter and optimise grip options during the preliminary design stages, without the need to run onerous calculations. The global shear capacity prediction formula is developed using five machine learning models. First, a finite element model database is developed. The influence of the opening diameter, web opening spacing, tee-section height, concrete topping thickness, the interaction degree, and the number of shear studs above the web opening are investigated. Reliability analysis is conducted to assess the design method and propose new partial safety factors. The Catboost Regressor algorithm presented better accuracy compared to the other algorithms. An equation to predict the shear capacity of composite cellular beams with hollow-core units is proposed by Gene Expression Programming. In general, the partial safety factor for resistance, according to the reliability analysis, varied between 1.25 and 1.26.

In this article, we describe a simple procedure for evaluating the sterility of nutrient media using a shear-horizontal surface acoustic wave (SH-SAW) biosensor. We used the SH-SAW biosensor platform to monitor the time-dependent phase responses of the material for the media that binds to a monolayer of 3-mercaptopropanyl-N-hydroxy succinimide on the biosensor surface. Increases in the phase shift less than 50% of the starting phase shift recorded 180 minutes after the sterilization indicate a successful sterility test of the media. Our devices were then applied to sterility testing using a viable Escherichia coli (E. coli) K-12 solution to confirm our hypothesis. Filtered LB Broth was the negative control, and a 24-hour culture of E. coli was the positive control. Before testing, the cell solution was pelleted, the media decanted, and then replaced with a 1x phosphate-buffered saline solution (1x PBS). Since we know that the N-hydroxysuccinimide residues will bind to amine groups, only in cases where microbial species are present will the surface binding increase greater than 50%. We confirmed our hypothesis using SH-SAW biosensors and overnight E. coli cultures. The sensitivity for our 250 MHz quartz SH-SAW sensors was calculated based on the response from the E. coli K-12 solution over the linear dynamic range, which appears to be 2x10^4 – 2x10^7 CFU per ml and has a sensitivity of S = 1.655x10^5 o m2 Kg-1. The limit of detection (LOD) for these sensors was calculated to be approximately 2x10^-9 grams (g), which is estimated to be approximately 2,000 Escherichia coli (E. coli) K-12 cells. However, the sensitivity and insertion loss remained approximately unchanged before and after coating the sensor with 3,3'-Dithiobis(succinimidyl) Propionate (DSP).

Acetamiprid is a broad-spectrum neonicotinoid insecticide used in agriculture to control aphids. While recent studies have documented resistance to acetamiprid in several aphid species, the underlying mechanisms are still not fully understood. In this study, we analyzed the transcriptome and metatranscriptome of a laboratory strain of the pea aphid, Acyrthosiphon pisum (Harris, 1776), with reduced susceptibility to acetamiprid after nine generations of exposure to identify candidate genes and the microbiome involved in the adaptation process. Sequencing of the transcriptome of both selected (RS) and non-selected (SS) strains allowed the identification of 14858 genes and 4938 new transcripts. Most of the differentially expressed genes were associated with catalytic activities and metabolic pathways involving carbon and fatty acids. Specifically, the alcohol-forming fatty acyl-CoA reductase (FAR) and acyl-CoA synthetase (ACSF2), both involved in the synthesis of epidermal wax layer components, were significantly upregulated in RS, suggesting that adaptation to acetamiprid involves the synthesis of a thicker protective layer. Metatranscriptomic analysis revealed subtle shifts in the microbiome of RS. These results contribute to a deeper understanding of acetamiprid adaptation by the pea aphid and provide new insights for aphid control strategies.

Gas and power networks are tightly coupled and interact with each other due to physically interconnected facilities. In an integrated gas and power network, a contingency observed in one system may cause iterative cascading failures, resulting in network wide disruptions. Therefore, understanding the impacts of the interactions in both systems is crucial for governments, system operators, regulators and operational planners, particularly, to ensure security of supply for the overall energy system. Although simulation has been widely used in the assessment of gas systems as well as power systems, there is a significant gap in simulation models that are able to address the coupling of both systems. In this paper, a simulation framework that models and simulates the gas and power network in an integrated manner is proposed. The framework consist of a transient model for the gas system and a steady state model for the power system based on AC-Optimal Power Flow. The gas and power system model are coupled through an interface which uses the coupling equations to establish the data exchange and coordination between the individual models. The bidirectional interlink between both systems considered in this studies are the fuel gas offtake of gas fired power plants for power generation and the power supply to LNG terminals and electric drivers installed in gas compressor stations and underground gas storage facilities. The simulation framework is implemented into an innovative simulation tool named SAInt (Scenario Analysis Interface for Energy Systems) and the capabilities of the tool are demonstrated by performing a contingency analysis for a real world example. Results indicate how a disruption triggered in one system propagates to the other system and affects the operation of critical facilities. In addition, the studies show the importance of using transient gas models for security of supply studies instead of successions of steady state models, where the time evolution of the line pack is not captured correctly.

Microwave technology has a potential application in the extraction of zinc from sulphide ores, knowledge of the dielectric properties of these ores plays a major role in the microwave design and simulation for any process. The dielectric properties of zinc sulfide concentrate for two different apparent densities—1.54 and 1.63 g/cm³—have been measured by using the resonance cavity perturbation technique at 915 and 2450 MHz during the roasting process for the temperature ranging from room temperature to 850 °C. The variations of dielectric constant, the dielectric loss factor, the dielectric loss tangent and the penetration depth with the temperature, frequency and apparent density have been investigated numerically. The results indicate that the dielectric constant increases as the temperature increases and temperature has a pivotal effect on the dielectric constant, while the dielectric loss factor has a complicated change and all of the temperature, frequency and apparent density have a significant impact to dielectric loss factor. Zinc sulfide concentrate is high loss material from 450 to 800 °C on the basis of theoretical analyses of dielectric loss tangent and penetration depth, its ability of absorbing microwave energy would be enhanced by increasing the apparent density as well. The experimental results also have proved that zinc sulfide concentrate is easy to be heated by microwave energy from 450 to 800 °C. In addition, the experimental date of dielectric constant and loss factor can be fitted perfectly by Boltzmann model and Gauss model, respectively.

During choriogenesis in insects, chorion (eggshell) is formed by surrounding follicular epithelial cells in ovarioles. However, the regulatory endocrine factor(s) activating choriogenesis and the chemical components on eggshell deserve further exploration. In two representative Coleopterans, a Coccinellid Henosepilachna vigintioctopunctata and a Chrysomelid Leptinotarsa decemlineata, genes encoding the 20-hydroxyecdysone (20E) receptor heterodimer, ecdysone receptor (EcR) and ultraspiracle (USP), and two chitin biosynthesis enzymes UDP-N-acetylglucosamine pyrophosphorylase (UAP) and chitin synthase (ChS1), were highly expressed in ovaries of the young females. RNA interference (RNAi)-aided knockdown of either HvEcR or Hvusp in H. vigintioctopunctata inhibited oviposition, suppressed the expression of HvChS1, and lessened the positive signal of Calcofluor staining on the chorions, which suggests the reduction of a chitin-like substance (CLS) deposited on eggshells. Similarly, RNAi of LdEcR or Ldusp in L. decemlineata constrained oviposition, decreased the expression of LdUAP1 and LdChS1, and declined CLS contents in the resultant ovaries. Knockdown of LdUAP1 or LdChS1 caused similar defective phenotypes, i.e., reduced oviposition and CLS contents in the L. decemlineata ovaries. These results, for the first time, indicate that 20E signaling activates choriogenesis in two Coleopteran species. Moreover, our findings propose the deposition of a CLS on the chorions.

The rock joint fissure slope in cold regions is prone to deformation and failure problems such as relaxation, tension and collapse under freeze-thaw (F-T) cycles. Based on the ideology of clean production and promoting the structural integrity of geotechnical projects in cold areas, this study designed and prepared aeolian-sand (AS) to replace part of river sand as a filling mortar material by taking advantage of the low cost and easy availability of AS. Investigations were carried out to determine the impact of varying proportions of AS in mortar on the microstructure and shear properties of the mortar-rock interface under F-T cycles. Therefore, F-T cycle testing, nuclear magnetic resonance (NMR) testing and shear testing were carried out on grout with different proportions of AS. The results show that the right proportion of AS replacement could enhance the shear deformation resistance and F-T resistance of the mortar-rock interface, and 30% proportion is the optimal proportion. By increasing of F-T cycles, the three types of specimens showed different degrees of particle spalling, shedding and cracking. The slurry-rock interface layer in the A (0%) group exhibited the most severe F-T deterioration, while the B (15%) group showed a lesser degree, and the C (30%) group performed the best. T2 spectrum curve and total spectrum area change law from the microscopic point of view to verify the 30% AS proportion mortar-rock interface F-T resistance is the strongest, followed by 15% AS proportion mortar, the weakest is ordinary mortar. The degradation of the mortar-rock bond is primarily due to the conversion of solid to liquid phases and the movement of internal water caused by fluctuating temperatures. The extent of F-T deterioration in the slurry-rock interface layer is greatly affected by the varying proportions of AS. The shear strength and shear stiffness of specific proportion of AS decreased with the increase of F-T cycles. For same F-T cycles, the shear strength and shear stiffness of group C (30%) were the highest, followed by group B (15%) and group A (0%). The grout material not only reinforces the F-T joint fissure slope, but also reduces the cost of grout reinforcement and promotes the clean production of geotechnical structures.

Soil extracellular enzyme activity (EEAs) and enzymatic stoichiometry (ES) can provide a crucial indication of changes in soil ecosystem's nutrient availability and the microbial resource limitations. However, the changing characteristics of soil EEAs and ES at different stages of the native succession process and their key drivers are unclear. In order to investigate the soil EEAs, ES and driving factors of soil under vegetation at different succession stages, we adopted the "spatio-temporal substitution" method to collect the surface soil of bryophyte community, herbaceous community, shrub community and tree community in the new volcanic lava platform of Wudalianchi Volcanic Nature Reserve. We measured seven soil EEA, including carbon(C)-acquiring enzyme (β-1,4-glucosidase (BG)), N-acquiring enzymes (β-N-acetyl-glucosaminidase (NAG) and leucine aminopeptidase (LAP)) and phosphorus (P)-acquiring enzyme (acid phosphatase (AP)) activities. The length and angle of vectors defined by ratios of enzyme activities (BG/(NAG + LAP) vs. BG/AP) were used to indicate relative microbial investments in C- (length), and N- and P- (angle) acquiring enzymes. Our results showed that the contents of TC, TN, TP, MBC, DOC and NO3-N in shrub community soil were significantly higher than those in bryophyte, herb and tree communities, and increased by 441%, 246%, 137%, 5570%, 12% and 484%, respectively. The highest soil EEA of C-, N- and P-acquiring were found in shrub community, and the soil EEAs/MBC of C-, N- and P-acquiring were the highest in bryophyte community. Enzyme C:N, C:P and N:P ratios increased progressively in the order of bryophyte, herb and shrub community, but the enzyme C:N, C:P and N:P ratios of tree community were both far less than shrub community. Vector lengths increased progressively in the order of bryophyte (1.16), herb (1.27), tree (1.29) and shrub (1.40), and Vector angles decreased progressively in the order of bryophyte (49.15°), herb (45.65°), Tree (45.31°) and shurb (44.54°), suggested that as succession progresses, soil microbial nutrients transforms from P limitation (angle＞45°) to N limitation (angle＜45°). Redundancy analysis showed that TC, TN, EC and C:N were important drivers of variation in soil EEAs and ES in vegetation at different succession stages. Our findings highlight that the primary succession process cause nutrient limitation transformation. Soil ES might be a sensitive indicator mediated by soil microorganisms to the relative resource limitation at different stages of the primary succession process.

Elevated serum uric acid (sUA) is associated with risk of developing cardiovascular disease (CVD). Here, we examined the prognostic significance of sUA and exercise capacity in 411 Japanese adults (age, ≥65; mean, 81 years) hospitalized for worsening CVD. Mean sUA was significantly higher in the 23% of patients on an sUA-lowering agent than in those not. When the patients were stratified by sUA into three groups (7.0 mg/dL), the high sUA group had significantly worse peak VO2 and composite endpoint (rehospitalization due to worsening CVD and all-cause mortality) compared with low and moderate sUA groups (P < 0.001). When the patients were stratified by sUA into five groups (sUA 10.0 mg/dL), the incidence of the composite endpoint was significantly higher in the highest sUA group compared with that in the reference group, but only in women. Univariate Cox regression analysis, but not a multivariate analysis, indicated that sUA was significantly associated with the composite endpoint. Although sUA and exercise capacity may have some degree of prognostic significance in older patients with CVD, this significance may differ between men and women.

A set of polymer composite bolted T-joints with novel configuration consisting of internal skeleton and external skin was fabricated using a prepreg-RTM co-curing molding process. Experiments were conducted to study their mechanical properties under bending load. A finite element model with a polymer resin area between the skin and skeleton was established and verified by the experimental results. Then, the damage propagation process and failure mechanism of the joint and the influence of three factors related to the layer characteristics of the skin and skeleton were investigated by the validated models. The results show that the bending stiffness and the yield limit load of the novel composite T-joint are 0.81 times and 1.65 times that of the 2A12 aluminum T-joint respectively, while at only 55.4% of its weight. The damage of the joint initiates within the resin area and leads to a degradation of the joint bending performances. The preferred stacking sequence of the skeleton is [0/+45/90/-45]ns when primarily subjected to bending loads. The decrease in bending performances is within 5% with the inclining angle of the skeleton less than 12 degrees. The more layers of 90° in the skin, the better bending performances of the joints, while the more layer of 0°, the poorer bending performances.

The statistical analysis of impact of the top 50 solar flares of X-class (1997-2023) on the global seismic activity, as well as on the earthquake preparation zones located in illuminated part of the globe and in the area of 5000 km radius around the subsolar point was carried out. It is shown by a method of epoch superposition that for all cases the increase of seismicity is observed, especially in the region around the subsolar point (up to 38%) during 10 days after the solar flare in comparison with preceding 10 days. The case study of aftershock sequence of strong M=9.1 earthquake (Su-matra-Andaman Islands, 26.12.2004) after the solar flare of X7.2 class (20.01.2005) demonstrated that the number of aftershocks with magnitude M≥2.5 increases more than 20 times after the solar flare with a delay of 7 days. For the case of the Darfield earthquake (M=7.1, 04.09.2010, New Zealand) it was shown that strong solar flares of class X and M probably triggered two strong aftershocks (M>6) with the same delay of 6 days on the Port Hills fault, which is the most sensitive to external electromagnetic impact from point of view of the fault electrical conductivity and orientation. Based on the obtained results the possible application of natural electromagnetic triggering of earthquakes is discussed for a short-term earthquake prediction using confidently recorded strong external electromagnetic triggering impacts on the specific earthquake preparation zones, as well as ionospheric perturbations due to aerosol emission from the earthquake sources recorded by satellites.

A portable laser photoacoustic sensor based on a Field-Programmable Gate Array (FPGA) is reported for methane detection. A tunable DFB diode laser in the 1654 nm wavelength range is used as an excitation source. The photoacoustic signal processing was implemented by a FPGA device. A small resonant photoacoustic cell is designed. The minimum detection limit (1σ) of 10 ppm for methane (CH₄) is demonstrated.

Optical backbone networks constitute the fundamental infrastructure employed today by network operators to deliver services to users. As network capacity is a key factor influencing optical network performance, it is important to understand how topological and physical properties impact its behavior and to have the capability to estimate its value. In this context, we propose here a method to evaluate the network capacity that relies on the optical reach to account for physical layer aspects, in conjunction with constrained routing techniques for traffic routing. As this type of routing can lead to traffic blocking, particularly due to the limitation on the number of wavelengths per fiber, we also propose a fiber assignment algorithm designed to deal with this problem. We apply this method to a set of randomly generated networks using a modified Waxman model, and for a network with 60 nodes, in a scenario without blocking, we obtain capacities of about 2.5 Pbit/s for a symbol rate of 64 Gbaud and about 5 Pbit/s for a symbol rate of 128 Gbaud. Remarkably, this duplication in the total network capacity is achieved by an increase in the total fiber length of only about 51%.

Finding a good MIMO system model also major issue in Wireless Communication system. It is facing with so many problem, one of the major problem is finding good system model in terms of capacity and transmitting antenna system. In this paper, we analyze the channel capacity of various MIMO system model with some constant SNR level and outage probability. We establish a novel idea for MIMO system models as consider as 2^N- MIMO system model and find-out change in channel capacity when different transmitting antennas with constant SNR and outage probability. The channel capacity ratio CC_R is presented here on the basis of 2^N- MIMO channel capacity model. Number of transmitted antenna presented in MIMO system is increases is well-known however paper shows change in capacity in simple form.

This study uses a mass-spring-damping system to simulate the repeated strain of liquefaction cyclic triaxial tests. The two results are compared in this paper to understand the feasibility of the mass-spring-damping system developed in this paper and the feasibility of future research on this related topic and development potential. The main factors affecting this mode's repeated strain are the spring coefficient k and the external force Q0. The spring coefficient has an inverse relationship but does not increase in multiples. The external force has a direct proportional relationship but does not increase the result- a non-multiple increase. When the pore water pressure of the liquefied cyclic triaxial test specimen rises, it will cause the specimen to liquefy, decreasing effective stress, shear modulus G, and damping ratio D, causing an increase in strain. The shear modulus and damping ratio are related to the spring coefficients k and c. Both are variables that change with time. This article takes an original thin-tube specimen at point A in the Yunlin area in Taiwan as a testing example. Through Mathematica software, it can be obtained that the mass m=1kg, the spring coefficient k=244e-0.1t kgf/cm, and the damping coefficient c=0.739e-0.257t kgf-s/cm and external force Q0=10.1sin2πt kg; Finally, this study selected the original thin-tube specimens from four locations in the Yunlin area, and simulated the repeated strain amount of the cyclic triaxial test specimens through a spring-damping system. The results show that the spring-damping system is feasible for simulated cyclic triaxial tests because the model is simple and the parameters are easy to understand and obtain, which also shows the extensibility of this model. Preliminary results of the research show that this model can further simulate the repeated strain obtained by cyclic triaxial tests without considering the increased trend in pore water pressure and the decrease in effective stress during cyclic loading.

A co-curing resin system consisting of 9368 epoxy resin for prepreg and 6808 epoxy resin for resin transfer molding (RTM) was developed. A corresponding preparation method of novel polymer composite bolted T-joint with internal skeleton and external skin was proposed based on prepreg-RTM co-curing process, and novel T-joints were fabricated. A series of conventional configuration T-joints based on RTM process and T-joints made of 2A12 aluminum alloy were prepared simultaneously. Bending performances were studied on these T-joints experimentally. The results indicate that 9368 epoxy resin and 6808 epoxy resin exhibit good compatibility in rheological and thermophysical properties. The novel T-joints prepared with prepreg-RTM co-curing process show no obvious fiber local winding or resin-rich regions inside, and the interface quality between internal skeleton and external skin is excellent. The main failure modes of the novel T-joint under bending load include separation of skin and skeleton and fracture along the thickness on the base panel; the skeleton carries the main bending load, but there is still load transfer between external skin and internal skeleton through their interface. The internal damages of the novel T-joint are highly consistent with surface damages observed visually, facilitating the detection and timely discovery of damages. The initial stiffness, damage initiation load, and ultimate load of the novel T-joint are 1.65 times, 5.89 times, and 3.45 times that of conventional T-joint, respectively. When considering the influence of density, the relative initial stiffness and relative ultimate load of the novel T-joint are 1.44 times and 2.07 times that of aluminum alloy T-joint, respectively.

The interface of a structural system in the soil is usually unsaturated. A decrease in the shear strength of the soil-structure interface can degrade the structure, especially under humid conditions. Studying the shear characteristics of the silt-concrete interface using a shear apparatus. Suction-controlled ring shear tests were carried out on the silt-concrete interface for three interface roughness values. The influence of the matric suction (s) and interface roughness (R) on the shear strength index of the silt-concrete interface was analyzed. The test results showed that high values of s and R improved the shear strength of the interface, but the result was affected by the net normal stress (NNS). High values of NNS and R improved the strain-hardening characteristics. NNS, s, and R significantly affected the interface shear shrinkage. The internal friction angle of the saturated interface was smaller than that of saturated silt, whereas the opposite occurred in the unsaturated state. The cohesion and internal friction angle of the interface rose with an increase in R, and they were larger than that of silt. A shear strength model of the silt and interface was established.

This paper is aimed at studying the temporal evolution of the surface displacements occurred over the past few years in the ocean-reclaimed platforms of the Shanghai megacity (China), which are mainly ascribable to consolidation processes of large dredger fills and alluvial deposits. With respect to previous analyses carried out over the same area, this work provides a joint multi-platform differential interferometry synthetic aperture radar (DInSAR) analysis, based on the application of the advanced Small BAseline Subset (SBAS) algorithm. This led us to retrieve long-term deformation time-series that are helpful for a better understanding of the on-going deformation phenomena. To this aim, we have exploited two sequences of SAR data collected by the ASAR/ENVISAT and by the COSMO-SkyMed (CSK) sensors, respectively, spanning the whole time period from 2007 to 2016. Unfortunately, the large time gap (of about three years) existing between the available ASAR/ENVISAT and CSK datasets gave rise to additional difficulties for their combination. Nevertheless, this problem has been faced by benefiting from the knowledge of a time-dependent model describing the temporal evolution of the expected deformations affecting the Shanghai ocean-reclaimed platforms.

Utilization of wasted heat instead of fuel combustion is effective to reduce primary energy consumption for mitigating global warming problem. Because wasted heat sources are not necessarily located close to areas of heat demand, one of the difficulties is that wasted heat has to be transferred from heat source side to heat demand side, which may require heat transportation over long distance. From this point we proposed and have examined new idea of heat transportation using ammonia-water as the working fluid which system is named Solution Transportation Absorption chiller, in short STA. Our previous studies of STA were mainly the experimental investigation with STA facility which cooling power was 25RT (90kW). As a result, the COP of STA was found almost same value 0.65 with the conventional absorption chiller without depending on the transportation distances. The simulation using AspenHYSYS also examined with same experimental condition. The experimental data showed good agreement with the simulation calculation. In this study, we examined the large-scale cooling power STA on simulation. The examination cooling powers were from 90 kW(25RT) to 3517 kW(1000RT). All cooling power achieved around COP 0.64 including pump power consumptions. In addition, we performed the dynamic simulation. As the results, there was no effect of pipeline size on the cooling capacities and mass flow rates. Furthermore, the stability time of the cooling capacities and mass flow rates were almost same regardless of the pipeline size and cooling capacity. In other words, STA may be achieved the same COP even though having various complex conditions compared with the conventional absorption chiller.

The catastrophic failure of two dams in Libya in the night of 10th and 11th September 2023, resulted in a significant amount of water and debris destroying a large part of the city of Derna, which is located downstream of the two dams. The flood caused more than 6000 fatalities and the dis-placement of thousands of people from the city. The dams failed due to heavy rainfall caused by the Medicane Daniel, resulting in intense precipitation and the dams overspilling after reaching full capacity. This paper analyses the consequences of the dam breach by modelling the flow discharge and the flooding of the city of Derna. The analysis compares the computed quantities with the findings of the post-event satellite image analysis from UNOSAT and Copernicus, the field reports, and information gathered from the social media through AI detection. The results allows to better understand the dynamics of the dam breach, its initial parameters and an assessment of the accu-racy of the results.

Background: Mental capacity is a fundamental aspect that enables patients to fully par-ticipate in various healthcare procedures. To assist healthcare professionals (HCPs) in assessing patients' capacity, especially in the mental health field, several standardized tools have been developed. These tools include the MacArthur Competence Assessment Tool for Treatment (MacCAT-T), the MacArthur Competence Assessment Tool for Clinical Research (MacCAT-CR), and the Competence Assessment Tool for Psychiatric Advance Directives (CAT-PAD). The core dimensions explored by these tools include Understanding, Appreciation, Reasoning, and Expression of a choice. Objective: This meta-analysis aimed to investigate potential differences in deci-sion-making capacity within the healthcare context among groups of patients with bi-polar disorder (BD) and schizophrenia spectrum disorder (SSD). Methods: A systematic search was conducted on Medline/Pubmed, and Scopus. Addi-tionally, Google Scholar was manually inspected, and a manual search of emerging re-views and reference lists of the retrieved papers was performed. Eligible studies were specifically cross-sectional, utilizing standardized assessment tools, and involving pa-tients diagnosed with BD and SSD. Data from the studies were independently extracted and pooled using random-effect models. Hedges g was used as a measure for outcomes. Results: Six studies were identified, with three studies using the MacCAT-CR, two studies the MacCAT-T, and one the CAT-PAD. The participants included 189 individuals with BD and 324 individuals with SSD. The meta-analysis revealed that patients with BD performed slightly better, and the difference was statistically significant, compared to patients with SSD, particularly in the domain of Appreciation (ES=0.23, 95% CI: 0.01 to 0.04, p=0.037). There was no statistically significant difference between the two groups for Understanding (ES=0.09, 95% CI: - 0.10 to 0.27, p=0.352), Reasoning (ES=0.18, 95% CI: - 0.12 to 0.47, p=0.074), and Expression of a choice (ES = 0.23, 95% CI: - 0.01 to 0.48, p=0.60). In the sensitivity analysis, furthermore, when considering only studies involving patients in symptomatic remission, the difference for Appreciation also resulted in non-significant (ES=0.21, 95% CI: -0.04 to 0.46, p=0.102). (ES=0.21, 95% CI: -0.04 to 0.46, p=0.102). Conclusions: These findings indicate that there are no significant differences between patients with BD and SSD during remission phases, while differences are minimal during acute phases. The usefulness of standardized assessment of capacity at any stage of the illness should be considered, both for diagnostic-therapeutic phases and for research and advance directives. Further studies are necessary to understand the reasons for the overlap in capacity between the two diagnostic categories compared in this study.

In order to develop novel botanical insecticides, the joint action of Ligusticum chuanxiong oil (LCO) and lemongrass oil (LO) against Aphis citricola van der Goot was determined systematically indoors and outdoors. The chemical profiles of LCO and LO as determined by gas chromatography- mass spectrometry analysis revealed that main compounds from LCO were Z-Ligustilide (44.58%) and Senkyunolide A (26.92%), and that of LO were geranial (42.16%) and neral (32.58%), respectively. The mixture of LCO and LO showed significant synergy against A. citricola, with a common-toxicity coefficient (CTC) value of 221.46 at the optimal ratio of LCO to LO (4: 1, w/w). Based on the results of solvents and emulsifiers screening, L. Chuanxiong oil · Lemongrass oil 20% emulsifiable concentrate (20% LCO · LO EC) was developed, which was confirmed to meet the requirements of a commercial pesticide by quality test. Field trials indicated that the insecticidal activity of the diluted 20% LCO · LO EC (1000 fold dilution) was comparable to conventional pesticide (20% imidacloprid EC) on A. citricola 7 days after application. Thus, the mixture of LCO and LO has the potential to be further developed as a botanical pesticide.

This study aimed to clarify the relationship between the joint and ligament structures of the subtalar joint and degeneration of the subtalar articular facet. We examined 50 feet from 25 Japanese cadavers. The number of articular facets, joint congruence, and intersecting angle were measured for the joint structure of the subtalar joint, and the footprint areas of the ligament attachments of the cervical ligament, interosseous talocalcaneal ligament (ITCL), and anterior capsular ligament were measured for the ligament structure. Also, subtalar joint facets were classified into Degeneration (+) and (-) groups according to degeneration of the talus and calcaneus. No significant relationship was identified between the joint structure of the subtalar joint and degeneration of the subtalar articular facet. In contrast, footprint area of the ITCL was significantly higher in the Degeneration (+) group than in the Degeneration (-) group for the subtalar joint facet. These results suggest that the joint structure of the subtalar joint may not affect degeneration of the subtalar articular facet. Degeneration of the subtalar articular facet may be related to the size of the ITCL.

The author demonstrates a stable Lagrangian solid modeling method, tracking the interactions of solid mass particles rather than using a meshed grid. This numerical method avoids the problem of tensile instability often seen with smooth particle applied mechanics by having the solid particles apply stresses expected with Hooke's law, as opposed to using a smoothing function for neighboring solid particles. This method has been tested successfully with a bar in tension, compression, and shear, as well as a disk compressed into a flat plate, and the numerical model consistently matched the analytical Hooke's law as well as Hertz contact theory for all examples. The solid modeling numerical method was then built into a 2-D model of a pressure vessel, which was tested with liquid water particles under pressure and simulated with smoothed particle hydrodynamics. This simulation was stable, and demonstrated the feasibility of Lagrangian specification modeling for fluid–solid interactions.

The human landscape transforming activity contributes to the global change of vegetation in different forms. Hunting is one of the most ancient human landscape-shaping activities. Feeders for hunting are particularly disruptive to vegetation. In the present study, we conducted a vegetation survey in these highly disturbed places. We are investigating the vegetation dynamics over several years in in the turkey oak–sessile oak zone, in two areas with different moisture and shade conditions (forest and clearing). One important background factor is changes in precipitation and temperature. The novelty of our present study lies in the fact that the observation takes place with continuous disturbance, where the human influence is very large. Our results confirm that the weed infestation be detectable at bait sites over a long period, and the interannual changes were typical in every year, according to the fact that in August, more weed species are usually present with a greater cover at the bait sites. The main meteorological factors played a role in the degree of weed infestation in each year. There was a higher proportion of vegetation regeneration in wetter years, while dry periods do not favor successional processes. With the drying of the climate, the disturbed areas are constantly losing their natural value, but wetter weather is not an automatic solution either. A more precise understanding of vulnerable systems and careful planning of treatment interventions is necessary.

This paper contains theoretical fundamentals of strut and tie models, used in unreinforced horizontal shear walls. Depending on support conditions and wall loading, we can distinguish models with discrete bars when point load is applied to the wall (type I model) or with continuous bars (type II model) when load is uniformly distributed at the wall boundary. The main part of this paper compares calculated results with the own tests on horizontal shear walls made of solid brick, silicate elements and autoclaved aerated concrete. The tests were performed in Poland. The model required some modifications due to specific load and static diagram.

As new vaccines reduce P. falciparum (Pf) cases, clinicians can focus on rescuing more children with cerebral malaria (CM). Adjunctive “therapeutically-rational exchange transfusion” (T-REX) refers to using special “Pf-resistant” donor red blood cells (RBCs) that secrete nano-sized RBC extracellular vesicles (EVs). Can some RBC EVs rapidly dislodge Pf-infected RBCs (iRBCs) sequestered in blood vessels and reduce inflammation? Does post-exchange “rebound parasitemia” reflect sequestration-reversal? We reviewed case-reports, EV and liposome studies, expert perspectives, and time-sequence data. In the AQUAMAT study, median coma-recovery time was 20 hours for artesunate. In contrast, a CM patient treated with type-O T-REX quickly began speaking (during the procedure). For other rapid-recovery CM patients, donor RBC variables had not been specified. Despite rapid Pf-killing, drugs need 20 hours to substantially reduce iRBC cytoadhesion while EVs can selectively bind distant inflamed tissues within 15 minutes. RBCs stressed by blood-bank storage and Pf infection secrete EVs. Post-exchange “rebound parasitemia” can occur within 60 minutes and may reflect release of sequestered iRBCs. Sequestration-reversal can be assessed by monitoring Pf parasitemia and total Pf biomass. New data suggest clinicians, working with transfusion- and laboratory-medicine physicians, can, and should, assess T-REX options and publish their findings to help clarify how RBC EVs may serve as therapeutic “decoy ligands.”

Wall Shear Stress (WSS) abnormalities in carotid artery blood flow are key hemodynamic factors leading to arterial endothelial damage, atherosclerotic plaque formation, and carotid artery stenosis. Precise simulation of carotid artery blood flow WSS in vitro play an important role in understanding the underlying hemodynamic mechanism of carotid artery stenosis. This study presents a design for a microfluidic cell culture chamber with a variable cross-section and a step structure, leveraging microfluidic technology and principles of fluid dynamics. We propose an optimization strategy for microchannel dimensions based on Computational Fluid Dynamics (CFD) simulations. This strategy aims to replicate the distinct WSS waveform features found at various locations within the carotid bifurcation as observed in vivo. Our simulations indicate that with a step height of 0.09 mm, a width of 4 mm for the initial segment, and 5 mm for the subsequent wider channel, the device can effectively model the characteristics of low oscillatory WSS seen at sites of carotid sinus stenosis. Furthermore, it accurately represents the high-magnitude pulsatile WSS waveforms in the more uniform arterial sections downstream of the carotid sinus. The study also reveals that vortex formation and variations in low oscillatory WSS within the stepped section of the microchannel correlate with the step's height and width, as well as with the dimensions of the wider channel section. An increase in step width leads to a decrease in both the vortex area and the magnitude of negative WSS oscillations. When the step height is less than 0.03 mm, vortex formation is inhibited, challenging the simulation of low oscillatory WSS patterns. The variable cross-section microfluidic channel developed in this study provides a platform for simulating carotid artery WSS waveforms and facilitates research into the interplay between low oscillatory WSS at sites of carotid sinus stenosis and arterial endothelial dysfunction.

A proportion of osteoarthritis (OA) patients are unsatisfied with post-operative outcomes following total joint replacement surgery (TJR), with insufficient pain relief or poor functional improvement. Predicting those will have poor outcomes would be beneficial for patients and clinicians. The aim of this study was to determine the relationship between baseline anthropometric data and the concentration of pre-operative serum and peri-operative synovial fluid (SF) cytokines with 7-month post-operative outcomes in a cohort of knee and hip OA patients. 160 OA patients were recruited who were scheduled for TJR. The concentration of 24 cytokines were measured in blood and SF by multiplex assay. EQ5Dindex health status was assessed pre-operatively and at 7-months post-operatively. 13% of patients were identified as non-responders based on EQ5Dindex. Compared to responders, non-responders were of higher BMI, had greater waist and hip circumference and had higher levels of SF leptin but lower levels of SF Resistin (p&lt;0.05). Linear regression analysis found a significant relationship between pre-operative body weight and post-operative response (ΔEQ5Dindex; r=0.222, p=0.049). The combination of body weight with SF amphiregulin and SF IL-6 provided an improved predictive model of post-operative response (r=0.470, p=0.035).

Due to the extraordinary mechanical properties of ultra-high-performance concrete (UHPC), the shear stirrups in UHPC beams could potentially be removed. The aim of this study is to determine the effect of beam height and steel fiber volume content on the shear behavior of non-stirrup UHPC beams under a larger shear span-depth ratio (up to 2.8). Eight beams were designed and fabricated, including six non-stirrup UHPC beams and two comparing stirrup-reinforced normal concrete (NC) beams. The experimental results demonstrated that the volume content of steel fiber could be a crucial factor affecting the ductility, cracking strength, and shear strength of non-stirrup UHPC beams and altering their failure modes. Additionally, the height of the beam had a considerable effect on its shear resistance. This study revealed that the French standard formulae were more accurate for the UHPC beams with larger shear span-depth ratios and PCI-2021 formulae greatly overestimate the shear capacity of UHPC beams with larger shear span-depth ratios. Xu’s formulae were more accurate for the steel fiber-reinforced UHPC beams with larger shear span-depth ratios.

In this study, a commercial sodium butyrate protected by a new buffer salt solution (NSB) was tested to determine whether it can be used as an antibiotic alternative in broiler production. 192 1-day-old broilers were randomly allocated to three dietary treatments: soybean meal diet (CON), antibiotic diet (ANT, basal diet + 100 mg/kg aureomycin), and NSB (basal diet + 800 mg/kg NSB). The growth performance, serum anti-inflammatory cytokines, intestinal morphology, gut barrier function, antioxidative parameters, SCFAs content, and cecal microbiota were analyzed. The result showed that NSB significantly improved ADFI, ADG (p < 0.01), and decreased FCR (p < 0.01). Serum anti-inflammatory cytokine IL-10 was up-regulated (p < 0.01), and pro-inflammatory TNF-α was down-regulated (p < 0.05) by NSB supplementation. H&E results showed that VH and VH: CD ratio significantly increased (p < 0.05) in the jejunum and ileum in the NSB group. Furthermore, ZO-1 (p < 0.01), claudin-1 (p < 0.01), and occludin (p < 0.05) in the jejunum and claudin-1 (p < 0.01) and mucin-2 (p < 0.05) in the ileum significantly up-regulated in the NSB group, respectively. Additionally, SOD (p < 0.05) and T-AOC/MDA ratio (p < 0.01) in the jejunum and SOD in the ileum were significantly increased (p < 0.05) in the NSB group. The MDA level also significantly increased (p < 0.01) in the ANT group in the jejunum. Propionic acid (p < 0.05) and butyric acid (p < 0.01) content significantly increased in the NSB group in the jejunum and ileum segments. The 16S rRNA sequencing results showed no significant difference (p > 0.05) in alpha and beta diversity among the groups. LEFSe analysis also indicated that Peptostreptococcaceae, Colidextribacter, Firmicutes, Oscillospira, and Erysipelatoclostridiaceae, which promote SCFA production (p < 0.05), were identified as dominant taxon-enriched bacterial genera in the NSB group. The Spearman correlation analysis revealed that Colidextribacter with ADFI, ADG, VH, claudin-1 (p < 0.05), and unclassified_f__Peptostreptococcaceae with ADFI, IL-10, and ZO-1 were positively correlated (p < 0.05). Furthermore, ADFI and ADG with IL-10, claudin-1, SOD, T-AOC, and butyric acid (p < 0.05), and similarly, ADG with VH (p < 0.05) showed a positive correlation. In conclusion, NSB enhanced the growth performance by improving jejunum and ileum morphology, serum anti-inflammatory cytokines, regulating intestinal barrier function and antioxidant capacity, SCFAs content, and cecum microbiota, showing its potential use as an alternative to antibiotics in poultry nutrition.

Surface initiated atom transfer radical polymerization (SI-ATRP) is one of the most versatile technique to modify the surface properties of material. Recent developed metal free SI-ATRP makes such technique more widely applicable. Herein photo-induced metal-free SI-ATRP of methacrylates, such as methyl methacrylate, N-isopropanyl acrylamide, and N,N- dimethylaminoethyl methacrylate, on the surface of SBA-15 was reported to fabricate organic-inorganic hybrid materials. SBA-15 based polymeric composite with adjustable graft ratio was obtained. The structure evolution during the SI-ATRP modification of SBA-15 was monitored and verified by FT-IR, XPS, TGA, BET, and TEM. The obtained polymeric composite showed enhanced adsorption ability for the model compound toluene in aqueous. This procedure provides a low cost, ready availability, and facile modification way to synthesize the polymeric composites without the contamination of metal.

There are several well-described molecular mechanisms that influence cell growth and are relat-ed to the development of cancer. Chemokines constitute a fundamental element which are not only involved in local growth but also affect angiogenesis, tumor spread and metastatic disease. Among them, the C-X-C motif chemokine ligand 12 (CXCL12) and its specific receptor the chemo-kine C-X-C motif receptor 4 (CXCR4) have been widely studied. The overexpression in cell mem-branes of CXCR4 has been shown to be associated with the development of different kinds of his-tological malignancies, such as adenocarcinomas, epidermoid carcinomas, mesenchymal tumors or neuroendocrine neoplasms (NENs). The molecular synapsis between CXCL12 and CXCR4 leads to the interaction of G proteins and activation of different intracellular signaling pathways in both gastroenteropancreatic (GEP) and bronchopulmonary (BP) NENs conferring greater ca-pacity for locoregional aggressiveness, epithelial-mesenchymal transition (EMT) and the ap-pearance of metastases. Therefore, it has been hypothesized how to design tools that target this receptor. The aim of this review is to focus on current knowledge of the relationship between CXCR4 and NENs, with a special emphasis on diagnostic and therapeutic molecular targets.

Shear connectors are used in steel beam–concrete slabs of composite frame and bridge structures to transfer shear force according to design loads. The existing Y-type perfobond rib shear connectors are designed for girder slabs of composite bridges. Therefore, the rib and transverse rebars of the conventional Y-type perfobond rib shear connectors are extremely large for the composite frames of building structures. We performed push-out tests of stubby Y-type perfobond rib shear connectors for composite frames. These shear connectors have relatively small ribs than conventional Y-type perfobond rib shear connectors. To confirm the shear resistance of these stubby shear connectors, we performed an experiment by using transverse rebars D13 and D16. The results indicate that these shear connectors have suitable shear strength and ductility for application in composite frame structures. The shear strengths obtained using D13 and D16 were not significantly different. However, the ductility of the shear connectors with D16 was 45.1% higher than that of the shear connectors with D13.

Most shear tests are performed as standard three- or four-point bending tests, i.e., on one-way simply supported specimens subjected to concentrated loads. The major disadvantage is that these conditions usually do not correspond to the support and load condition of real structures. Structural members such as beams or slabs, are often multi-span components and subjected to distributed loads. As a consequence, the complex shear behavior, including crack kinematics, shear transfer mechanisms, and shear capacity, is studied almost only simply supported members with concentrated load. Positive impacts on the shear behavior resulting from continuous systems and distributed loads are thus neglected in the derivation of calculation models and in the development of design specifications. To incorporate the effect of continuous members and distributed loading conditions, more experimental investigations are necessary. Therefore, a total of 16 bending shear tests on CFRP reinforced concrete members without shear reinforcement were carried out. The tests specimens were tested as simply supported beams or as simply supported beams with loaded cantilever to simulate the continuous system with concentrated and distributed loads. Furthermore, the shear slenderness was varied by using different span lengths and degrees of restraint in the systems with intermediate support. All test specimens were made of high-strength concrete and were reinforced with a multilayer grid-like CFRP reinforcement in longitudinal direction. There was no shear reinforcement installed in the investigated shear span. This paper focuses the influence of the support conditions and load arrangements on crack development as well as on shear strength.

To investigate the bioactivities of fresh garlic and its processed product, black garlic, we conducted comparative analyses of antioxidant, anti-inflammatory, innate immune activation and anti-cancer activities, in addition to chemical composition (sugar, amino acid, polyphenol contents) of these materials. Simultaneous assay using neutrophil-like cells showed that fresh garlic exhibited antioxidant and innate immunostimulatory activities, whereas black garlic displayed a potent anti-inflammatory effect. The antioxidant activity index was correlated with phenol and flavonoid contents, while the innate immunostimulatory activity was correlated with fructan content. Furthermore, some black garlics with low fructose content were found to inhibit the proliferation of UM-UC-3 cancer cells, while other black garlics rich in fructose increased UM-UC-3 cell proliferation. It was shown that the thermal processing steps of fresh garlic could change the composition of sugars, antioxidants, and amino acids, which have different effects on neutrophil-like cells and UM-UC-3 cells, as well as on bioactivities.

Estimating ground surface PM2.5 with fine spatiotemporal resolution is a critical technique for exposure assessments in epidemiological studies of its health risks. Previous studies have utilized monitoring, satellite remote sensing or air quality modeling data to evaluate the spatiotemporal variations of PM2.5 concentrations, but such studies rarely combined these data simultaneously. We develop a three-stage model to fuse PM2.5 monitoring data, satellite-derived aerosol optical depth (AOD) and community multi-scale air quality (CMAQ) simulations together and apply it to estimate daily PM2.5 at a spatial resolution of 0.1˚ over China. Performance of the three-stage model is evaluated using a cross-validation (CV) method step by step. CV results show that the finally fused estimator of PM2.5 is in good agreement with the observational data (RMSE = 23.00 μg/m^3 and R2 = 0.72) and outperforms either AOD-retrieved PM2.5 (R2 = 0.62) or CMAQ simulations (R2 = 0.51). According to step-specific CVs, in data fusion, AOD-retrieved PM2.5 plays a key role to reduce mean bias, whereas CMAQ provides all-spacetime-covered predictions, which avoids sampling bias caused by non-random incompleteness in satellite-derived AOD. Our fused products are more capable than either CMAQ simulations or AOD-based estimates in characterizing the polluting procedure during haze episodes and thus can support both chronic and acute exposure assessments of ambient PM2.5. Based on the products, averaged concentration of annual exposure to PM2.5 was 55.75 μg/m3, while averaged count of polluted days (PM2.5 > 75 μg/m3) was 81, across China during 2014. Fused estimates will be publicly available for future health-related studies.

Polydimethylsiloxane (PDMS) is one of the most popular elastomers and has been used in different fields, especially in biomechanics research. Among the many interesting features of this material, its hyperelastic behaviour stands out, which allows the use of PDMS in various applications, like the ones that mimic soft tissues. However, the hyperelastic behaviour is not linear and needs detailed analysis, especially the characterization of shear strain. In this work, two approaches, numerical and experimental, were proposed to characterize the effect of shear strain on PDMS. The experimental method was implemented as a simple shear testing associated with 3D digital image correlation and was made using two specimens with two thicknesses of PDMS (2 and 4 mm). A finite element software was used to implement the numerical simulations, in which four different simulations using the Mooney-Rivlin, Yeoh, Gent, and Polynomial hyperelastic constitutive models were performed. These approaches showed that the maximum value of shear strain occurred in the central region of the PDMS, and higher values emerged for the 2 mm PDMS thickness. Qualitatively, in the central area of the specimen, the numerical and experimental results have similar behaviours and the values of shear strain are close. For higher values of displacement and thicknesses, the numerical simulation results move further away from experimental values.

Scene classification plays an important role in the intelligent processing of high-resolution satellite (HRS) remotely sensed image. In HRS image classification, multiple features, e.g. shape, color, and texture features, are employed to represent scenes from different perspectives. Accordingly, effective integration of multiple features always results in better performance compared to methods based on a single feature in the interpretation of HRS image. In this paper, we introduce a multi-task joint sparse and low-rank representation model to combine the strength of multiple features for HRS image interpretation. Specifically, a multi-task learning formulation is applied to simultaneously consider sparse and low-rank structure across multiple tasks. The proposed model is optimized as a non-smooth convex optimization problem using an accelerated proximal gradient method. Experiments on two public scene classification datasets demonstrate that the proposed method achieves remarkable performance and improves upon the state-of-art methods in respective applications.

Optical modes bearing optical vortices are important light systems in which to encode information. Optical vortices are robust features of optical beams that do not dissipate upon propagation. Thus decoding the modal content of a beam is a vital component of the process. In this work we present a method to decode modal superpositions of light beams that contain optical vortices. We do so using shear interferometry, which presents a simple and effective means of determining the vortex content of a beam, and extract the parameters of the component vortex modes that constitute them. We find that optical modes in a beam are easily determined. Its modal content can be extracted when they are of comparable magnitude. The use of modes of well defined topological charge but not well defined radial-mode content, such as those produced by phase-only encoding, are much easier to diagnose than pure Laguerre-Gauss modes.

The antioxidant properties and polyphenol content of some selected aromatic plants grown in Greece were studied. Plants were refluxed with 60% methanol after acid hydrolysis. The phenolic substances were quantified by HPLC-DAD. The antioxidant capacity of the extracts was determined with the Rancimat test using sunflower oil as substrate. Free radical scavenging activity was measured using the stable free radical 1, 1-diphenyl-2-picrylhydrazyl (DPPH). Results were compared with standard BHT and ascorbic acid. Total phenol concentration of the extracts was estimated with Folin-Ciocalteu reagent using gallic acid as standard.

Background: This study aimed to investigate the association between the internal derangement of the temporomandibular joint (TMJ), in particular the severity of disc displacement (DD), and the presence of generalized joint hypermobility (GJH) in growing patients evaluated on magnetic resonance images (MRI). The study also investigated the relationship between the stages of DD severity and age. Methods: This cross-sectional study has been conducted on a pre-orthodontic population (8-16 years). The GJH was assessed with the Beighton test (cutoff ≥ 4) and the final sample of 56 patients was divided into two groups: a Study Group, 30 subjects with GJH, and a Control Group, 26 subjects without GJH. The disc position was evaluated on MRI and the severity of DD was classified in four stages. Pearson's χ2 Test was performed for the analysis of the statistical correlation. Results: A statistically significant relationship between GJH and disc position was found, in particular a disc displacement with reduction (DDwR) and DD severity. It also emerged a positive association between the severity of DD and age, that increased with increasing age. Conclusions: Growing patients with GJH have a higher risk of developing DD and with more severe stages. The risk of developing DD and the severity increases with increasing age.

The study evaluated potassium peroxymonosulfate (PPMS) efficacy against rifampicin-resistant Salmonella Infantis (rif-SI), Escherichia coli (E. coli), Salmonella Infantis (SI), Newcastle disease virus (NDV) and avian influenza virus (AIV). The assessment encompassed varied concentrations, organic material conditions, and exposure durations to comprehensively evaluate PPMS efficacy. Moreover, PPMS’s efficacy was tested on diverse carrier surfaces and clothing to evaluate its bactericidal and virucidal potential. At the recommended concentrations (1X), PPMS effectively inactivated all pathogens within 5 sec, except for NDV, which required 30 sec in the presence of organic materials. At 0.5X, PPMS successfully inactivated E. coli, AIV and NDV within 5 sec in the absence of organic material. However, rif-SI and SI necessitated 30 sec for inactivation. Most pathogens were inactivated within 30 sec, with the exception for AIV, which was inactivated within 5 sec. PPMS effectively eliminated rif-SI on all carriers within 30 sec. Moreover, at both concentrations, PPMS successfully inactivated AIV on all carriers within 30 sec, except on stainless steel at 0.5X. Furthermore, PPMS at both concentrations required 5 and 30 sec, respectively, to inactivate AIV on the rayon sheet. Therefore, due to its demonstrated efficacy against a wide range of pathogens across diverse surfaces, PPMS emerges as a crucial alternative disinfectant significantly enhancing biosecurity on and around chicken farms. found in and around animal farms, slaughterhouses, and hospitals.

We propose a deep-learning approach for the joint MIMO detection and channel decoding problem. Conventional MIMO receivers adopt a model-based approach for MIMO detection and channel decoding in linear or iterative manners. However, due to the complex MIMO signal model, the optimal solution to the joint MIMO detection and channel decoding problem (i.e., the maximum likelihood decoding of the transmitted codewords from the received MIMO signals) is computationally infeasible. As a practical measure, the current model-based MIMO receivers all use suboptimal MIMO decoding methods with affordable computational complexities. This work applies the latest advances in deep learning for the design of MIMO receivers. In particular, we leverage deep neural networks (DNN) with supervised training to solve the joint MIMO detection and channel decoding problem. We show that DNN can be trained to give much better decoding performance than conventional MIMO receivers do. Our simulations show that a DNN implementation consisting of seven hidden layers can outperform conventional model-based linear or iterative receivers. This performance improvement points to a new direction for future MIMO receiver design.

Temporomandibular disorders (TMD) affect a high percentage of children and adults worldwide. Surgery may be indicated in severe or recalcitrant case. Several recent advancements in the TMD and temporomanidbular joint (TMJ) surgery have elevated understanding and ability to treat affected patients. We discuss recent advances in TMD epidemiology, juvenile idiopathic arthritis (JIA) of the TMJ, and surgical techniques and technologies. Technical advancements have been identified in TMJ arthroscopy, treatment of TMJ subluxation and dislocation, and extended prosthetic total TMJ reconstruction (eTMJR). Overall, this review provides valuable insights into significant recent advancements of TMJ disorders and their surgical management.

Over recent years, the swine industry has witnessed the withdrawal of antibiotics and continuous regulation of zinc and copper oxides in the early-life nutrition of piglets. Due to this development, alternative ingredients or additives from plant sources have been tremendously explored. Therefore, this study's objective was to evaluate the effect of dietary supplementation with tannins on weaned piglets’ growth performance, serum antioxidant capacity, and immune status using a meta-analysis approach. With only the inclusion of non-challenged weaned piglets, a total of 16 studies with parameters of interest were deemed eligible after a two-step screening process following a comprehensive literature search in the scientific databases of Web of Science, Scopus, ScienceDirect, PubMed, and Google Scholar. Two main categories of data, including the study’s characteristics and response variables (growth performance, serum antioxidant, and immune indices), were extracted. Applying the random-effects models, Hedges’ g effect size of supplementation with tannins was calculated using the R software to determine the standardized mean difference (SMD) at a 95% confidence interval. Sub-group analysis and meta-regression further explored heterogeneity (PSMD 0.05, I2 50%, n ≥10). Supplementation with tannin reduced average daily gain (p = 0.20) and feed conversion ratio (p 0.01); however, it increased average daily feed intake (p = 0.07) and final body weight (p 0.01). Meta-regression models indicated that tannin dosage and supplementation duration were directly associated with tannins' effectiveness on productive performance. In the serum, the concentration of glutathione peroxidase, superoxide dismutase, and total antioxidant capacity were elevated (p 0.01) in response to tannins supplementation, while malondialdehydes was reduced (p 0.01). Likewise, decreased immunoglobin A (p = 0.47) and increased immunoglobin M and G levels (p 0.01) were detected. In conclusion, dietary supplementation with tannins, particularly with chestnut and grape seed proanthocyanidins, increases the productivity of weaned piglets. At the same time, it is a possible nutritional strategy to mitigate oxidative stress and stimulate gut health. Thus, supplementing chestnut and grape seed proanthocyanidin tannins in the early phase of swine production could be used to alleviate the incidence of diarrhea.

Financial capacity instruments are psychometric tools designed to evaluate individual decisional capacity based on financial decisions. As tests are complex and need special conditions for administration and evaluation, it is difficult to use them in daily geriatric clinics. Our scoping review objective was to evaluate existing financial capacity instruments from the perspective of simplicity and portability. We evaluated one English speaking knowledge database (Medline) using a dedicated MeSH terminology. The review yielded one independent instrument, The Semi-Structured Clinical Interview for Financial Capacity, that can be easy adapted for every-day clinical use. It is simple to understand and perform and do not need trained personnel for administration. It can be finalized in 15 minutes. Initially validated on 261 subjects (with different forms of cognitive impairment), it showed good accuracy and precision mainly in subjects with cognitive impairment. The test is less apt to detect early or fluctuating cognitive impairment. Simplicity, the main advantage of the test, allows gamification fact that increases portability. Familiar images (coins, money) that are used for performing simple tasks does not need complex translation and adaptation. In form of a game, the test is suitable for serial administration, increasing the chance for early capacity reduction detection. Results reflect a physician judgement related to the subjects’ capacity to understand and execute simple financial instructions and not financial proficiency scores. The main limitation of our review is that we investigated only one, English speaking, knowledge database. The scoping strategy generated a financial capacity instrument that can be used in geriatric clinics for early diagnostic of decisional capacity reduction. Further studies are needed to evaluate the reliability and validity of the test in conditions of serial administration and in populations having various financial experience.

Eccentric punching shear can occur in concrete slab-column connections when the connection is subjected to shear and unbalanced moments. Typically, this situation results in edge and corner columns and is thus a common practical case. However, most punching experiments in the literature are concentric punching shear. This paper presents a developed database of eighty-eight experiments of flat slabs under eccentric punching shear, including a summary of the testing procedure of each reference and a description of the slab specimens. Additionally, a linear finite element analysis of all the specimens is included to determine the relevant sectional shear forces and moments. Finally, the ultimate shear stresses from the database experiments are compared to the shear capacities determined with ACI 318-19, Eurocode 2 NEN-EN 1992-1-1:2005, and the Model Code 2010. The comparison shows that the Model Code 2010 is the most precise in the predictions with an average tested over predicted ratio of 0.96 and a coefficient of variation of 27.96%. It can be concluded that this study represents the inconsistencies of the currently used design methods and the lack of experimental information.

The paper argues that universal approaches to infiltration and drainage in permeable media that pivot around capillarity and that led to dual porosity, non-equilibrium, or preferential flow need to be replaced by a dual process approach. One process has to account for relatively fast infiltration and drainage based on Newton's shear flow, while the other one is responsible for storage and relatively slow redistribution of soil water by focusing on capillarity. Already Schumacher (1864) postulated two separate processes. However, Buckingham's (1907) and Richards' (1931) apparent universal capillary-based approach to flow and storage of water in soils dominated. The paper introduces the basics of Newton's shear flow in permeable media. It presents experimental support for the four presumptions of (i) sharp wetting shock fronts; (ii) that move with constant velocities; (iii) atmospheric pressure prevails behind the wetting shock front; (iv) laminar flow. It further discusses the scale tolerance of the approach, its relationship to Darcy's (1856) law, and its extension to solute transport.

To get more data concerning the influence of fertilizers (organic and mineral) on different forage plants existing in North-eastern Romanian grassland, the mass fractions of 14 essential, enzymatic, or considerd toxic elements was determined by Instrumental Neutron Activation Analysis together with the amount of crude proteins, ash, fibres as well as ether fact extract. Final results showed a significant variance of the content of analysed elements on organic as well as on mineral fertilized experimental plots, i.e. the content increased in 24% of plots, decreased in 23%, and remained unchanged in 45% while in 8% of plots their content was below the detection limits, as the case of Se. At the same time, an increase content of crude protein and ether extract was evidenced in fertilized grasses for all applied fertilizers while other global indicators such as neutral and acid fibre of sufuric lignin content decreased, suggesting significant higher nutritional values of fertilized forage plant.

Climate change is a global issue that draws widespread attention from the international society. As an important component of the climate system, the water cycle is directly affected by climate change. Thus, it is very important to study the influences of climate change on the basin water cycle with respect to maintenance of healthy rivers, sustainable use of water resources, and sustainable socioeconomic development in the basin. In this study, by assessing the suitability of multiple General Circulation Models (GCMs) recommended by the Intergovernmental Panel on Climate Change, Statistical Downscaling Model (SDSM) and Automated Statistical Downscaling model (ASD) were used to generate future climate change scenarios. These were then used to drive distributed hydrologic models (Variable Infiltration Capacity, Soil and Water Assessment Tool) for hydrological simulation of the Yangtze River and Yellow River basins, thereby quantifying the effects of climate change on the basin water cycle. The results showed that suitability assessment adopted in this study could effectively reduce the uncertainty of GCMs, and that statistical downscaling was able to greatly improve precipitation and temperature outputs in global climate mode. Compared to a baseline period (1961–1990), projected future periods (2046–2065 and 2081–2100) had a slightly decreasing tendency of runoff in the lower reaches of the Yangtze River basin. In particular, a significant increase in runoff was observed during flood seasons in the southeast part. However, runoff of the upper Yellow River basin decreased continuously. The results provide a reference for studying climate change in major river basins of China.

One-dimensional chain of core-shell pairs connected by ideal springs enables design of the metamaterial demonstrating the negative effective density and negative specific thermal capacity. We assume that the molar thermal capacity of the reported metamaterial is governed by the Dulong-Petit law in its high temperature limit. The specific thermal capacity depends of the density of the metamaterial; thus, it is expected to be negative, when the effective density of the chain is negative. The range of the frequencies enabling the effect of the negative thermal capacity is established. Dependence of the effective thermal capacity on the exciting frequency for various core/shell mass ratios is elucidated. The effective thermal capacity becomes negative in the vicinity of the local resonance frequency ω0 in the situation when the frequency ω approaches ω0 from above. The effect of the negative effective thermal capacity is expected in metals in the vicinity of the plasma frequency.

Temporomandibular disorders (TMD) is a group of orofacial pain conditions which is the most common non-dental pain complaint in the maxillofacial region. Due to the complexity of the etiology and often cyclical nature of the disease, the diagnosis and management of TMD remain a challenge where consensus is still lacking in many aspects. While clinical examination is considered the most important process in the diagnosis of TMD, imaging may serve as a valuable adjunct in selected cases. Depending on the type of TMD, many treatment modalities have been proposed, ranging from conservative options to open surgical procedures. In this review, the authors discuss the present thinking in the etiology and classification of TMD, followed by the diagnostic approach and the current trend and controversies in management.

In the paper, we prove a joint limit theorem in terms of weak convergence of probability measures on $\mathbb{C}^2$ defined by means of the Epstein ζ(s;Q) and Hurwitz ζ(s,α) zeta-functions. The limit measure in the theorem is explicitly given. For this, some restrictions on the matrix Q and parameter α are required. The theorem obtained extends and generalizes Bohr-Jessen’s results characterising asymptotic behaviour of the Riemann zeta-function.

This paper focuses on a joint model to analyse longitudinal proportion and survival data. After transforming the longitudinal proportional data by a logit function, we adopt a partially linear mixed-effect model for it, in which nonlinear function of time is fitted via using B-splines technique and a centered Dirichlet Process Mixture Model (CDPMM) is specified for a general distribution of random effects. The survival data is assumed to a Cox proportional hazard model, the sharing random effects joint model is developed for the two types of data. Combining the Gibbs sampler and the Metropolis-Hastings algorithm, we propose a Bayesian Lasso (BLasso) method to simultaneously estimate unknown parameters and select important covariates. Simulation studies are conducted to investigate the finite sample performance of the proposed methods. An example from the MA.5 research experiment is used to illustrate the proposed methodologies.

A large set of undrained compression triaxial tests was carried out on different types of cohesionless soils, from sands to silty-sands and silts. Shear wave velocity measurements were carried out alongside. These tests exhibited distinct state transitions ranging from flow liquefaction to strain softening or strain hardening. With the purpose of defining a framework to assess soil liquefaction, it was found that the ratio between the shear wave velocity (VS0) and the peak undrained deviatoric stress, qpeak, VS0/qpeak, could be accurately used to define a boundary between liquefaction and strain hardening for sands, and between strain softening and strain hardening for silty-sands and silts. Since this ratio is a function of the tested material, it was also discovered that the prediction of these boundaries could be made as a function of soil grading, namely via the coefficient of uniformity, CU. Despite not being regarded as a strong geomechanical parameter, CU is easily determined from a grain-size distribution test and it has an empirically proven correlation with critical state parameters.

Shear thickening fluids (STF) are a class of fluids whose viscosity significantly rises under external loads. The research on these fluids has been advancing in recent years regarding prospective practical applications, including developing impact-absorbing composites. Following the green agendas governments and legislators advocate, this study investigates the combination of STF and other sustainable materials. Cork is a naturally occurring cellular material with a negative carbon footprint and superior energy absorption properties. With varying concentrations of STF material, cork agglomerates were formed. Notably, the analysed blends are homogeneous, contrasting with previous literary works. A series of experiments were conducted in quasi-static and dynamic conditions to determine the various mechanical responses. STF appears to influence the mechanical behaviour of cork agglomerates by providing softer deceleration rates and dispersing more energy through disaggregation mechanisms.

Today, Colebrook’s equation is mostly accepted as an informal standard for modeling of turbulent flow in hydraulically smooth and rough pipes including transient zone in between. The empirical Colebrook’s equation relates the unknown flow friction factor (λ) with the known Reynolds number (R) and the known relative roughness of inner pipe surface (ε/D). It is implicit in unknown friction factor (λ). Implicit Colebrook’s equation cannot be rearranged to derive friction factor (λ) directly and therefore it can be solved only iteratively [λ=f(λ, R, ε/D)] or using its explicit approximations [λ≈f(R, ε/D)]. Of course, approximations carry in certain error compared with the iterative solution where the highest level of accuracy can be reached after enough number of iterations. The explicit approximations give a relatively good prediction of the friction factor (λ) and can reproduce accurately Colebrook’s equation and its Moody’s plot. Usually, more complex models of approximations are more accurate and vice versa. In this paper, numerical values of parameters in various existing approximations are changed (optimized) using genetic algorithms to reduce maximal relative error. After this improvement computational burden stays unchanged while accuracy of approximations increases in some of the cases very significantly.

The availability of current land cover and land use (LCLU) information for monitoring the status of land resources has considerable value in ensuring sustainable land use planning. Similarly, the need to provide updated information on the extent of LCLU change in West Africa has become apparent, given the increasing demand for land resources driven by the rapid population growth in the sub-region. SERVIR West Africa, a regional consortium jointly supported by USAID and NASA to foster the use of geospatial and earth observation data and science for decision-making on critical environmental and food security challenges, in collaboration with the Food and Agriculture Organization of the United Nations (FAO), is building technical capacity in the sub-region to develop and implement harmonized regional land cover classification system for LULC change monitoring in West Africa, based on the Land Cover Meta Language (LCML-ISO 19144-2). This article focuses on the process, potential opportunities, outputs of this collaboration, exemplary use cases, and recommendations for the next steps.

Star block-copolymers (SBCs) are macromolecules formed by a number of diblock copolymers anchored to a common central core, being the internal monomers solvophilic and the end monomers solvophobic. Recent studies have demonstrated that SBCs constitute a self-assembling building blocks with specific softness, functionalization, shape, and flexibility. Depending on different physical and chemical parameters the SBCs can behave as flexible patchy particles. In this paper, we study the rotational dynamics of isolated SBCs using a hybrid mesoscale simulation technique. We compare three different approaches to analyse the dynamics: the laboratory frame, the non-inertial Eckart's frame, and a geometrical approximation relating the conformation of the SBC to the velocity profile of the solvent. We find that the geometrical approach is adequate when dealing with very soft systems while in the opposite extreme, the dynamics is best explained using the laboratory frame. On the other hand, the Eckart frame is found to be very general and to reproduced well both extreme cases. We also compare the rotational frequency and the kinetic energy with the definitions of the angular momentum and inertia tensor different from recent publications.

The meniscus is a meniscus-shaped fibrocartilage tissue located between the femur and tibia，it is mainly composed of meniscus cells and related extracellular matrix.The synovial limbus area of the knee joint capsule near the meniscus is divided into red areas with rich blood vessels and white areas with less blood supply according to the distribution of blood vessels,there is a transition zone called the red and white zone between the two;Red zone has better self-repair ability,The injury in this area can be treated by conservative treatment or surgical suture;Once the white area of the meniscus is torn and involves the free edge area,It is often necessary to partially remove the damaged meniscus.When most of the entire meniscus is severely torn and involved,not only the course of the disease is very long, but it cannot be repaired by sutures,Often a subtotal or total meniscus resection is required,whether it is a partial meniscus resection, a subtotal meniscus resection or a complete resection.In the later period, it may cause quadriceps atrophy and osteoarthritis (OA）.OA is a refractory multi-system disease,involve the patient’s peripheral joints,it has high disability and teratogenicity, and is very harmful to human health.Chondrocyte pyrolysis, degradation, and inflammation play a vital role in the destruction of OA articular cartilage and chondrocyte apoptosis.Meniscus stem cells have strong proliferation and differentiation ability,has become one of the hot spots in the field of meniscus repair,this article studies the role of meniscal stem cells in the development of OA.

Optical networks, characterized by using optical fibers as a transmission medium, constitute the fundamental infrastructure employed today by network operators to deliver services to users. As network capacity is one of the key factors influencing optical network performance, it is important to comprehend its limitations and have the capability to estimate its value. In this context, we revisit the concept of capacity from various perspectives, including channel capacity, link capacity, and network capacity, thus providing an integrated view of the problem. Hence, we review the fundamental concepts behind optical networks, along with the basic physical phenomena present in optical fiber transmission and provide methodologies for estimating the different types of capacities, mainly using simple formulations. In particular, we propose a method to evaluate the network capacity that relies on the optical reach to account for physical layer aspects, in conjunction with capacitated routing techniques for traffic routing. We apply this method to three reference networks and obtain capacities ranging from tens to hundreds of Terabits/s. Whenever possible, we also compare our results with published experimental data to understand how they relate.

In this paper, we dive into the exciting world of wireless communication, focusing on how millimeter-wave technology and Multiple-Input Multiple-Output phased array antennas are shaping the future of 5G and the upcoming 6G technologies. We cover the latest advancements in millimeter-wave and beam-forming technologies, emphasizing their role in enhancing network security and efficiency in automotive vehicles through dual radar communication. Our discussion spans the benefits, applications, challenges, and solutions of these technologies individually from millimeter-wave to beam-forming technology and joint radar communications, alongside a look at their theoretical and practical implementations. We emphasize the integration of beam-forming technology in joint radar communications for future automotive vehicles and its impact on automotive systems, smart cities, and the Internet of Things (IoT). Looking ahead, we discuss the potential of these technologies to transform future tech landscapes, while also addressing the security implications of merging communication and radar capabilities. This paper aims to provide a clear view of the advancements and prospects of millimeter-wave, beam-forming, and dual radar communication technologies.

Geological structures such as joints and faults in rock mass have significant influence on open pit mining. Hence, it is critical to develop a understanding of dynamic joint behaviour under blasting loading. This in turn can provide both theoretical and practical guidance to improve blasting rock fragmentation and associated bucket excavating efficiency. In this paper, delayed blasting on the highwall bench at Baiyunebo open-pit mine was used as an example, a nonlinear joint blasting model was also constructed. By simplifying the blasting wave propagation velocity, the P-wave normal incidence to the joint was obtained. The peak vibration velocity was 0.33m/s at 3.0s. The S-wave reflected by the joint interface was first reflected backward and then forward, which the peak vibration velocity was 0.027 m/s. By combining the relevant stress and displacement theories of type I and II cracks, the equipotential diagrams of the stress and displacement field with the vibration velocity of the particle were obtained. σx was positive in the direction of 0~330° and subjected to tensile stress, whereas σy was positive in the direction of 0~180° and under tensile stress. The longitudinal σy along joint was low in compressive stress distribution area and did not affect surrounding rock at the time. The stress concentration appeared in the lower right corner. Based on the continuous behavior of stress wave in joints, the asymmetry and continuous changes reflected in the whole process could not be analysed by the contour diagram. Hence, ANSYS used to analyse distribution of the stress field. The intensity of the shock wave after detonation was greater than that of the rock strength. Subsequently, the sub-layer shock wave supplemented the shock wave energy that was not enough to break the rock and induced further cracking. This was able to be visualized by the degree of color change post-processing. It was concluded that with the attenuation of the detonation wave energy, the stress exhibited a decreasing trend in this process. According to distribution of the peak effective stress, it was found that the peak value first increased to 10-12 MPa and then showed a downward trend. Overall, the results were validated against the finite element simulation and mathematical analysis.

The greater Wellington region, New Zealand, is highly vulnerable to large earthquakes because it is cut by active faults. Bulk water supply pipelines cross the Wellington Fault at several different locations, and there is considerable concern about severe disruption of the provision of reticulated water supplies to households and businesses in the aftermath of a large earthquake. A number of policy initiatives have been launched encouraging householders to install rainwater tanks to increase post-disaster resilience. However, little attention has been paid to potential health hazards associated with consumption of these supplies. To assess health hazards for householders in emergency situations, six 200-litre emergency water tanks were installed at properties across the Wellington region, with five tanks being allowed to fill with roof-collected rainwater and one tank being filled with municipal tapwater as a control. Such tanks are predominantly set aside for water storage, and once filled, feature limited drawdown and recharge. Sampling from these tanks was carried out fortnightly for one year, and samples analysed for E. coli, pH, conductivity, a range of major and trace elements, and organic compounds, enabling an assessment of the evolution of water chemistry in water storage tanks over time. Key findings were that the overall rate of E.coli detections in the rain-fed tanks was 17.7%, which is low in relation to other studies. We propose that low incidences of E.coli may be due to biocidal effects of high zinc concentrations in tanks, originating from unpainted galvanised steel roof cladding. Lead concentrations were high compared to other studies, with 69% of rain-fed tank samples exceeding the World Health Organisation’s health-based guideline of 0.01 mg/L. Further work is required to determine risks of short-term consumption of this water in emergency situations.

: Shear-wave elastography (SWE) has become popular in clinical practice for many diseases.However, there are not adequate research for spleen-related diseases.This study aimed to investigate the potential of quantitative values obtained through SWE in evaluating spleen pathologies in the pediatric population and to demonstrate its perfomance to differentiate splenomegaly-related diseases.Research group retrospectively included children with pathological diagnoses related to spleen from November 2016 to April 2021 and they were categorized three groups as portal hypertension (PH), benign lymphoid hyperplasia (BLH), malignant infiltration (MI).Spleen sizes and parenchymal stiffness were also calculated for each group.Subsequently, mean spleen stiffness in each compared with normal values within the same age group.In total 2781 children (1379 children for study group, 1402 children for control group) were enrolled to the study.The highest stiffness were observed in the PH group, which is statistically higher than others (p&lt;0.05). Although the mean spleen stiffness in the group with BLH was higher than the control and MI group, the difference was not statistically significant (p=0.08).The mean stiffness in the group with MI was significantly lower than both the control group (p=0.005) and PH (p=0.01).In conclusion, using SWE in the differential diagnosis of etiologies causing splenomegaly, could make important contribution.

Calcareous sand deposits are widely distributed along the shoreline in ropical and subtropical regions. Microbially induced calcite precipitation treatment (MICP) is a relatively new method to improve the stiffness and strength of the soil. Little is known about the small-strain shear modulus and damping ratio of MICP-treated calcareous sand, which are two crucial parameters for the prediction of the dynamic behavior of soil. A series of resonant column tests are performed to investigate the dynamic performance of MICP-treated calcareous sand, with special attention paid to the influence of treatment duration and confining stress on the stiffness and damping characteristics. The relationship between the initial dynamic shear modulus and unconfined compressive strength is analyzed. Additionally, the empirical equations of the reference shear strain between treatment duration and confining stress are given. The G/G0 of MICP-cemented calcareous sand presents a higher strain sensitivity than that of untreated sand, and its attenuation pattern can be described by Hardin-Drnevich model. The σc has an apparent effect on the degradation characteristics of the dynamic shear modulus of MICP-treated calcareous sand with a low cementation level, however, its effect decreases with the increasing treatment duration. The relationship between the reference shear strain and the treatment duration and confining stress can be described by a power and a linear formula, respectively.

Woodland strawberry (Fragaria vesca L.) is an underutilized plant species, appreciated by consumers for its qualitative features. Utilizing technical means of production, such as plant biostimulants, that can increase crop productivity and quality could be highly important in woodland strawberry cultivation. The scope of the present study was to appraise the influence of two biostimulants (Trichoderma atroviride and plant protein hydrolysate) - used either alone or combined - on plant performance and economic profitability of two woodland strawberry genotypes (‘Alpine’ and ‘Regina delle Valli’). Overall, data showed that ‘Alpine’ had the highest productive performances, whereas ‘Regina delle Valli’ revealed the highest fruit qualitative traits. T. atroviride inoculation and V-PH application significantly boosted plant marketable yield (+20.5% for T. atroviride and +12.9% for V-PH), total sugars (+1.9% for Trichoderma and +1.4% for V-PH) and anthocyanins (+14.1% for T. atroviride and +9.8% for V-PH) compared to non-treated plants. Plants supplied with both biostimulants had higher marketable yield (+34.8%), mean fruit weight (+6.0%), fruit dry matter (+13.8%), total sugars (+3.5%), ascorbic acid (+12.7%), flavonoid (+26.3%) and anthocyanins (+29.9%) compared to non-treated plants. Furthermore, our study revealed that the highest fruit polyphenols concentration was recorded in both genotypes treated with the combination of biostimulants and in ‘Regina delle Valli’ sprayed with V-PH, whereas the highest antioxidant activity was found in ‘Regina delle Valli’ fruit when plants were supplied with both biostimulants. Our study pointed out that the application of microbial and non-microbial biostimulants, especially in combination, might be an useful strategy for improving performances of underutilized species and, therefore, encourage its cultivation, valorisation and economic profitability (+10195.3 €/ha when plants were exposed to both biostimulants).

Generally, when cognitive radio users are in Underlay mode, through the analysis of the electromagnetic spectrum in time, frequency, space, and field of multiple dimensional data accounts for judging the inherent correlation of the radio spectrum used/idle state, this is the realization of cognitive radio users (secondary users, SUs) efficient access to the foundation of the limited spectrum resources. Therefore, how to efficiently use of spectrum status of each SU implementation of reception multidimensional combination forecasting is the core of this paper addressing the problem. In this paper, we propose a deep-learning hybrid model called TensorGCN-LSTM based on the tensor data structure. The model treats SUs deployed at different spatial locations under the same frequency and the spectrum status of SUs themselves under different frequencies in the task area as nodes and constructs two types of graph structures. Graph convolutional operations are used to sequentially extract corresponding spatial-domain and frequency-domain features from the two types of graph structures. Then, the long short-term memory (LSTM) model is used to fuse the spatial, frequency, and temporal features of the cognitive radio environment data. Finally, the prediction task of the spectrum distribution situation is accomplished through fully connected layers. Specifically, the model constructs a tensor graph based on the spatial similarity of SUs' locations and the frequency correlation between different frequency signals received by SUs, which describes the electromagnetic wave's dependency relationship in spatial and frequency domains. LSTM is used to capture the electromagnetic wave's dependency relationship in the temporal domain. To evaluate the effectiveness of the model, we conducted ablation experiments on LSTM, GCN, GC-LSTM, and TensorGCN-LSTM models using simulated data. The experimental results show that our model achieved better prediction performance in RMSE, and the correlation coefficient R2 of 0.8753 also confirmed the feasibility of the model.

In order to further investigate the study of the effect of grouped stud effect on the force properties of stud connector, based on the premise that the correctness of the finite element simulation method in this paper, finite element modeling of grouped stud connectors was developed, the grouped stud effect and its sensitivity factors were analyzed, to validate the recommended formula for calculating the shear capacity of grouped stud connectors. Results show that the number of grouped stud rows and row spacing have a significant effect on the grouped stud effect, and the unevenness coefficient of grouped stud force Ⅰ is negatively correlated with the number of grouped stud rows as well as the grouped stud row spacing. For grouped stud connectors with commonly used concrete grades greater than C50 and height-to-diameter ratios greater than 4 in steel-concrete composite structural bridges, which is insensitive to changes in the concrete strength grades and the length of the studs. The direction of force transmission for the grouped stud changes with the change of loading angle, and the unevenness coefficient of force for the grouped stud will therefore be reduced. By comparing the results of the 62 existing groups of grouped stud connectors push-out tests, the mean value of the ratio of tested to calculated values is found to be 1.12, the variance is 0.023, the dispersion is small, it is shown that the recommended formula has a high degree of accuracy. The results of this paper can be used as a theoretical basis for the study of the shear stress performance of grouped stud connectors.

A composite beam is a structural member that behaves as a single unit by using shear connectors between a concrete slab and an H-shaped steel girder. The composite ratio is crucial and determined by the shear connectors' ability to withstand the horizontal shear forces between the concrete and steel girder. In this study, a U-shaped composite beam was designed, which differs from conventional composite beams as it allows the use of a steel girder as a formwork. Moreover, angle-type shear connectors, instead of stud-type connectors, were employed. Based on this design, large-scale U-shaped composite beams with angle-type shear connectors were fabricated, and load tests were conducted to analyze the behavior after composite action and the influence of shear connector spacing. Additionally, the strength of the angle-type shear connectors used in this paper was evaluated through finite element analysis. Finally, a strength evaluation method for composite beams of this configuration was proposed.

The need for miniaturized shear force sensors is expanding, particularly for biomedical applications. Examples include measuring interfacial shear stresses between a human and an external device (e.g., footwear or a prosthesis). However, there are considerable challenges in designing a shear sensor for these applications due to the need for a small package, low power requirements, and resistance to interference from motion artifact and electromagnetic fields. This paper presents the design, fabrication, and characterization sensor that measures two-axis shear force by detecting displacement between a color panel and a red, green, and blue light-sensing photodiode. The sensor response to applied displacements and forces was characterized under benchtop testing conditions. We also present the design of a prototype wireless version of the sensor for integration into footwear. The sensor exhibited strong agreement with gold standard measurements for two axis shear displacements (R2>0.99, RMSE≤5.0 µm) and forces (R2>0.99, RMSE≤0.94 N). This performance, along with the sensor’s scalability, miniaturized form, and low power requirements make it well-suited a variety of biomedical applications.

Among the most important variables in the design of falling film microreactors (FFMRs) is the liquid film thickness as well as the gas/liquid interfacial area, which dictate the mass and heat transfer rates. In a previous work conducted in our lab the characteristics of a free-falling Newtonian liquid film have been studied and appropriate correlations have been proposed. In this work the geometrical characteristics of a non-Newtonian shear thinning liquid, flowing in an inclined open microchannel, have been experimentally investigated and design correlations that can predict with reasonable accuracy the features of a FFMR have been proposed. The test section used was an open μ-channel with square cross section (Wo=1200 μm) made of brass which can be set to various inclination angles. The liquid film characteristics were measured by a non-intrusive technique that is based on the features of a μ-PIV system. Relevant CFD simulations revealed that the volume average dynamic viscosity over the flow domain is practically the same as the corresponding asymptotic viscosity value, which can thus be used in proposed the design equations. Finally, a generalized algorithm for the design of FFMRs, containing non-Newtonian shear thinning liquids, is suggested.

To further explore the bearing capacity and sustainable construction of vacuum drainage pipe (VDP) piles, field tests were carried out to compare and analyze the ultimate single pile bearing capacity, pile side friction and pile end resistance of ordinary piles and vacuum drainage pipe piles. The effect of the VDP pile on energy conservation and emission reduction in practical projects is discussed. The results shows that the VDP pile basically eliminated the soil squeeze and did not cause excessive relative displacement of pile and soil after vacuum consolidation. The VDP pile enhances pile side friction resistance, resulting in a 17.6% increase in ultimate bearing capacity compared to traditional piles. The VDP pile method can reduce carbon emissions by 31.4% compared to traditional methods. This study provides guidance for the production and design of VDP piles in the future and demonstrates their potential for energy conservation and emission reduction benefits compared to traditional methods.

Motivated by the way animals react in nature, we introduce a fully-connected neural-network model, which incorporates the external pattern presented to the system as a fundamental tool of the recognition process. In this new scenario, in the absence of this external field, memories are not attractors inside basins of attraction, as in usual attractor neural networks, although basins may be created according to the external pattern, thus allowing storing a much larger number of memories. The key point consists in calibrating the influence of the external pattern such as to cancel the noise generated by those memories not correlated with the external pattern.We illustrate how this proposal works by including this new contribution in the standard Hopfield model, showing a significant increase in its recognition capacity (typically by a factor $10^{2}$). As an additional feature of this model, we show its ability to react promptly to changes in the external environment, a crucial attribute of living beings. This procedure can be applied to a wide variety of neural-network models to increase considerably their recognition and reaction capabilities.

Propolis is a bee product widely used as a dietary supplement and included in sweets or baby foods due to its well-known antioxidant and nutritional properties that are directly correlated with its phenolic composition. For this reason, this study analysed the total contents of flavones and flavonols, flavanones and dihydroflavonols, and the antioxidant capacity by using the methods of ABTS and linoleic acid/β-carotene in 99 samples of propolis from Spain and Chile. A rapid method was developed for quantifying these parameters in raw propolis using near infrared (NIR) spectroscopy with an optical fibre probe of remote reflectance applied directly to the ground up sample. The models developed allow the determination of the total of flavones and flavonols (0-183 mg rutin/ g propolis), of the total of flavanones and dihydroflavonols (9-109 mg pinocembrin/ g propolis extract), and the antioxidant capacity by the ABTS method (0-3212 nmolesTrolox/ mg of propolis) and of linoleic acid/β-carotene (22-86% inhibition). The NIR spectroscopy models were applied in external validation to different samples of the calibration group, which led to the conclusion that the methods developed provide significantly identical data to the initial chemical data of reference.

Osteoarthritis and rheumatoid arthritis are common cartilage and joint diseases that globally affect more than 200 and 20 million people, respectively. Several transcription factors have been implicated in the onset and progression of osteoarthritis, including Runx2, C/EBPβ, HIF2α, Sox4, and Sox11. IL-1β also leads to osteoarthritis through NF-ĸB, IκBζ, and Zn²⁺-ZIP8-MTF1 axis. IL-1, IL-6, and TNFα play a major pathological role in rheumatoid arthritis through NF-ĸB and JAK/STAT pathways. Indeed, inhibitory reagents for IL-1, IL-6, and TNFα provide clinical benefits for rheumatoid arthritis patients. Several growth factors, such as BMP, FGF, PTHrP, and Indian hedgehog, play roles regulating chondrocyte proliferation and differentiation. Disruption and excess of these signaling cause genetic disorders in cartilage and skeletal tissues. FOP, an autosomal genetic disorder characterized by ectopic ossification, is induced by mutant ACVR1. mTOR inhibitors were found to prevent ectopic ossification by ACVR1 mutations. ACH and related diseases are autosomal genetic diseases, which manifest severe dwarfism. CNP is currently the most promising therapy for ACH. In these ways, investigation of cartilage and chondrocyte diseases at molecular and cellular levels sheds light on the development of effective therapies. Thus, identification of signaling pathways and transcription factors implicated in these diseases is important.

This paper describes the load capacity of short fiber-reinforced polymer lugs with Ti-6Al-4V selective laser-melted bushings with the original embedded element surface roughness and after sandblasting and vibratory finishing. Lugs are an important part of pin-joints. Adhesion between PA6 and SLM produced titanium is not fully studied. The cohesive zone material Mode II model parameters were calibrated experimentally by extruding a cylindrical bushing along the lug axis. The values of the maximum equivalent tangential contact stress were fitted for cases with investigated embed element roughness. The critical fracture energy for tangential slip was also estimated. Validation of the constructed CZM Mode II models with the results of strength experiments was performed. In both the experiment and the calculation, greater bushing roughness provides greater lug load-bearing capacity. The presented models can be used for the preliminary evaluation of SFRP PA6 parts with titanium embedded elements bearing capacity.

Delta parallel robot has been widely used in precision parts processing, handling, sorting, and precision assembly, with high efficiency and motion stability being its important performance indexes. Any small line segment corner in trajectory planning causes tangential discontinuous trajectory abrupt change, and the process vibration and shock caused by it seriously affect its high-speed and high-precision performance. In this paper, a trajectory planning method combining Cartesian space and joint space is proposed. Firstly, the vector method and micro-element integration method are used to establish the complete kinematics and dynamics equations of the Delta parallel robot, and the inverse kinematics/dynamics model-solving program is written based on Matlab software. Secondly, the end-effector trajectory of the Delta parallel robot is planned in Cartesian space, and the data points and inverse control points of the end-effector trajectory are obtained by the normalization method. Finally, the data points and control points are mapped to the joint space through the inverse kinematics equation, and the fifth-order B-spline curve is adopted for quadratic trajectory planning, which realizes the high-order continuous smoothing of trajectory planning. The simulation and experiment results show that the trajectory smoothing performance of continuous high-order curvature change can be improved using the proposed method, the tracking error of the end-effector is reduced by 21.12%, and the peak torques change of three joints is reduced by 3.5%, 11.6% and 1.6%, respectively.

Ankle joint flexion and extension exercises play an important role in the rehabilitation training of patients who have been injured or bedridden for a long time before and after surgery. Accurately guiding patients to perform ankle flexion and extension exercises can significantly reduce deep vein thromboembolism. Currently, most ankle rehabilitation devices focus on assisting patients with ankle flexion and extension movements, and there is a lack of devices for effectively monitoring these movements. In this study, we designed an ankle joint flexion and extension movement monitoring device based on a pressure sensor. It is composed of an STM32 microcontroller, a pressure sensor, an HX711A/D conversion chip, and an ESP8266 WiFi communication module. The value of force and effective number of ankle joint flexion and extension movements were obtained. An experimental device was designed to verify the accuracy of the system. The results showed that the device can effectively monitor and control ankle flexion and extension movements remotely, ultimately ensuring that the patient can effectively monitor and grasp the active ankle pump movement.

This paper addresses the problem of low accuracy of conventional channel estimation and signal detection in complex fields like mines; and the problem of replacing the deep receiver at the receiver side with a deep neural network requires a large amount of data for training and slow training time. Combining the receiver side with traditional communication knowledge, a channel estimation and signal detection method based on the joint ReEsNet and SDRNet under the mine is proposed. The detailed step is to use ReEsNet network for interpolation of conventional channel estimation. Then, on the basis of ReEsNet, the output data is channel equalized and pilots removed, and the previously processed data is input to SDRNet to perform signal recovery. In the complex mine environment, the MSE values are 2e-2 for LS, 6e-3 for MMSE, and 8.44e-5 for ReEsNet at the 1500th sample data for interpolation compared to the conventional channel estimation. the MSE of ReEsNet is the smallest and is closer to the real channel estimation. Compared with the proposed joint channel estimation and signal detection methods, fewer trainable parameters reduce 97% of the parameters compared to CCRNet and 84% of the parameters compared to CNNNet; their detection results, however, are not very different.

Abstract: (1) Background: Minimally-invasive sacroiliac joint (SIJ) fusion is the preferred surgical intervention to treat chronically severe pain associated with SIJ degeneration and dysfunction. (2) Methods: This paper details the ten-step surgical procedure associated with the postero-inferior approach using the PsiF™DNA Sacroiliac Joint Fusion System. (3) Results: The posterior surgical approach with an inferior operative trajectory (postero-inferior) utilizes easily identifiable landmarks to provide the safest, most direct access to the articular joint space for transfixing device placement. Implanting the device through the subchondral bone, provides maximum fixation and stabilization of the joint by utilizing an optimal amount of cortical bone-implant interface. Approaching the joint from the inferior trajectory also places the implant perpendicular to the S1 endplate at a “pivot point” near the sacral axis of rotation, which addresses the most significant motion of the joint. (4) Conclusions: Further observational data from real-world clinical use are encouraged to further validate this procedure as the surgical preference for minimally-invasive SIJ fusion.

The purpose of this study was to investigate the changes in anterior knee laxity (AKL), stiffness, general joint laxity (GJL), and genu recurvatum (GR) during the menstrual cycle in female non-athletes and female athletes with normal and irregular menstrual cycles. Participants were 19 female non-athletes (eumenorrhea, n=11; oligomenorrhea, n=8) and 15 female athletes (eumenorrhea, n=8; oligomenorrhea, n=7). AKL was measured as the amount of anterior tibial displacement at 67 N - 133 N. Stiffness was calculated as change in (Δ)force/Δ anterior displacement. The Beighton method was used to evaluate the GJL. The GR was measured as the maximum angle of passive knee joint extension. AKL, stiffness, GJL, and GR were measured twice in four phases during the menstrual cycle. Stiffness was significantly higher in oligomenorrhea groups than in eumenorrhea groups, although no significant differences between menstrual cycle phases were evident in female non-athletes. GR was significantly higher in the late follicular, ovulation, and luteal phases than in the early follicular phase, although no significant differences between groups were seen in female athletes. Estradiol may affect the stiffness of the periarticular muscles in the knee, suggesting that GR in female athletes may change during the menstrual cycle.

Joining of aluminium alloys to steels has been extensively studied, especially in the automotive sector. However, aluminium alloys are known to be difficult to join with steels when methods involving fusion welding are used because of hot cracking problem. Hence, a high strength joint between these dissimilar metals would be of benefit especially in reducing the weight of products. In this work the torch brazing method was applied to join AR500 steel with AA7075 aluminium alloy using Al-Si-Zn base filler metal at various flame times. The effect of the brazing work on the intermetallic phase formation and the mechanical strength of the joints were investigated. In this work, the maximum shear load obtained was 6460 N and the presence of the intermetallic phases had reduced the shear strength of the brazed joints. However, the torch brazing process using Al-Si-Zn filler metal had successfully facilitated the joining of these dissimilar metals.

Sequential hypothesis test and change-point detection when the distribution parameters are unknown is a fundamental problem in statistics and machine learning. We show that for such problems, detection procedures based on sequential likelihood ratios with simple one-sample update estimates such as online mirror descent are nearly second-order optimal. This means that the upper bound for the algorithm performance meets the lower bound asymptotically up to a log-log factor in the false-alarm rate when it tends to zero. This is a blessing, since although the generalized likelihood ratio (GLR) statistics are optimal theoretically, but they cannot be computed recursively, and their exact computation usually requires infinite memory of historical data. We prove the nearly second-order optimality by making a connection between sequential analysis and online convex optimization and leveraging the logarithmic regret bound property of online mirror descent algorithm. Numerical and real data examples validate our theory.

(1) Background: Patella and achilles tendon injuries have become increasingly prevalent due to an increasingly active population. These injuries can cause significant dysfunction which is especially true for elite athletes. Standard B-Mode ultrasound has been useful in the diagnosis of these injuries, however, only to a limited extent. Shear wave elastography (SWE) can aid in evaluation by objectively measuring tissue stiffness. Prior studies have proven shear wave values can be used to evaluate tendon tissue noting differences in healthy versus pathologic tendons. One main limitation remains a lack of normative data for specific tendon tissues which we aim to address in this study; (2) Methods: A cross-sectional study of healthy volunteers aged 18-65 without lower extremity injury was evaluated using A Samsung RS85 Prestige ultrasound machine with a 14L-2 MHz transducer. Shear wave values were collected in a standardized manner for the patellar tendon at one location, as well as the achilles tendon at the midportion and insertional areas; (3) Results: Data for 54 healthy adult patellar and achilles tendons was collected bilaterally. The mean SWE average of the patellar tendon (P1-P3) for all subjects was 96.3 +/- 10.9 kPA. A higher BMI was correlated with a decrease in patella tendon kPA and the mean PT1 was higher for males compared to females (adjusted mean 96.4 kPA for males and 88.5 kPA for females, mean difference = 7.9 kPA; P = 0.009). The mean SWE average of the insertional Achilles (AT1-AT3) for all subjects was 101.7 +/-16.2 kPA and for the midportion achilles (MTP1-MTP5) was 145.6 +/- 18.8 kPA. There was a decrease in kPA for insertional Achilles measurements in those with a higher BMI, but this did not reach statistical significance (p=.12); (4) Conclusion: This study provides normative SWE values for the patella and achilles tendon using the Samsung RS85. These values can be used for comparison to pathological tissue by means of the same examination protocol to better understand tendon degeneration. Further studies are warranted as to how SWE can be applied to the diagnosis of tendinopathy, partial and full-thickness tears, and response to treatment.

Bare slope instability is a prevalent concern. The root system of, herbaceous vegetation enhances the shear strength of shallow–slope soil. Indoor experiments were conducted on rootless undisturbed soil (RUS) and undisturbed soil with a root system (USRS) using a triaxial compression apparatus to analyze the slope stability of composite soil with a Tagetes erecta root system. Significance tests and correlation analysis of the factors affecting shear performance were conducted using R software. The slope reinforcement, effect by the plant root system was simulated under 24 working conditions using the MIDAS finite element method. The results revealed the influence of the–root content (RC), moisture content (MC), and stress on the shear strength of USRS, the contribution degree, and the variables’ influences on slope stability. Both RUS and USRS exhibited strain hardening during shearing. The internal friction angle (φ) and cohesion (c) of USRS were negatively and positively correlated with the RC and MC (root burial depth), respectively, and a good fit was obtained for the relationship. The maximum deviatoric stress during shear failure was 1.29 times higher for USRS than for RUS. The RC (root depth) was positively correlated with the slope safety coefficient and the slope of the line under different working conditions, whereas the slope gradient was negatively correlated with the slope safety coefficient. The reinforcement effect by the root system resulted in a 13.2% increase in the safety coefficient and improved stability of slopes with a gradient larger than 1.5%. This article investigated the mechanism of the root–soil system and, the effects of different influencing factors on the shear strength of the soil, and slope stability. The findings provide new insights into shallow slope stability in practical slope protection projects.

This study aims to assess the interface shear adhesion behaviour between compacted clay and a metallic surface. A new testing approach was developed in this study for this purpose. The proposed method is simple and requires neither advanced equipment nor special test procedures, and thus represents an improvement on existing practice in this field. The experimental program involves determining the interface shear adhesion strength of reconstituted Kaolin clay/metallic surface where the Kaolin clay testing specimens were compacted dynamically at different energy levels and moisture contents. In general, the results show that the interface shear adhesion strength increases as the dry density of the clay increases, whereas it decreases as the moisture content increases. Furthermore, the results in this study reveal a unique multistage interfacial shear adhesion strength behaviour as the moisture content changes that could be related to the compaction curve of the clay. The observed behaviour, in this study, could be interpreted in terms of the effect of clay dry density and moisture content on the contact area and moisture-induced capillary adhesion at clay particles-continuum interface surface.

Increasing traffic loads and changes in code provisions lead to deficits in shear and flexural capacity of many existing highway bridges. Therefore, a lot of structures in Europe and North America are expected to require refurbishment and strengthening in the future. This projection is based on the current condition of many older road bridges. Different strengthening methods for bridges exist to extent their service life, all having specific advantages and disadvantages. By applying a thin layer of carbon textile reinforced mortar (CTRM) to bridge deck slabs and the webs of prestressed concrete bridges, the fatigue and ultimate strength of these members can be increased significantly. The CTRM-layer is a combination of a corrosion resistant carbon fibre reinforced polymer (CFRP) fabric and an efficient mortar. In this paper, the strengthening method and the experimental results obtained at RWTH Aachen University are presented.

Quercetin is a flavonoid with a low molecular weight that belongs to the human diet's phenolic phytochemicals and non-energy constituents. Quercetin has a potent antioxidant capacity, being able to capture Reactive Oxygen Species (ROS), reactive nitro-gen species (RNS), and Reactive Chlorine Species (ROC), which act as reducing agents by chelating transition metal ions. Its structure has five functional hydroxyl groups, which work as electron donors and are responsible for capturing free radicals. In addition to its antioxidant capacity, it was described different pharmacological properties of Quercetin, such as carcinostatic properties, antiviral, antihypertensive, anti-inflammatory, protection of Low-Density Lipoprotein (LDL) oxidation, and inhibi-tion of angiogenesis are developed in this review.

This paper has two objectives: the first, to analyze the mediating effect of teacher empowerment between innovation culture and innovation capacity, and between inclusive leadership and innovation capacity; the second, to analyze the moderating effects of the school context on the innovation capacity. Data were collected in a representative sample of secondary schools in Valencia, Spain. The research model adopted is structural equation modeling, using the partial least squares (PLS) technique. The model has confirmed that teacher empowerment mediates between innovation culture and innovation capacity and between inclusive leadership and the innovation capacity. It is found that the educational context does not moderate the relationships in the proposed analysis model. This paper emphasizes the role of teacher empowerment in educational innovation and extends the knowledge of culture and leadership in the school organization.

This study aimed to investigate the fatigue performance and interfacial strengthening mechanisms of Al6061-to-Cu dissimilar lap joints via electromagnetic pulse welding (EMPW). The load-bearing capacity of the joints at discharge voltages of 14 kV and 16 kV was superior to that of 12 kV. Furthermore, the fatigue life of the 14 kV joints was one order of magnitude higher compared to the 12 kV joints. SEM observation of the fatigue fracture surface revealed the presence of typical "tire-mark" fatigue striations only in the 14 kV joint, indicating higher ductility and the ability to withstand extended plastic deformation. Notably, ultra-fine nanocrystalline Al2Cu phase, amorphous phase, and numerous dislocations hindered EBSD acquisition in the transition zone. Nevertheless, dense low-angle grain boundaries (LAGBs) and refined grains were examined at the bonding interface. This suggests that the high-velocity collision caused severe plastic deformation and led to the formation of substructures. The interfacial strength was attributed not only to the "wave-like" or "inverted hook-like" diffusion layer but also to the presence of refined grains along the interface and nanocrystalline Al2Cu in the transition zone. Furthermore, the hybrid nanocrystalline-amorphous microstructure strengthened the joint by regulating the balance between strength and ductility.

Microbiome research has gained considerable interest due to the emerging evidence of its impact on human and animal health. Similar to higher organisms, the gut-associated microbiota of mosquitoes affect host fitness and other phenotypes. It is now well established that microbes can alter pathogen transmission in mosquitoes, either positively or negatively, and avenues are being explored to exploit microbes for vector control. However, less attention has been paid to how microbiota affect phenotypes that impact vectorial capacity. Several mosquito and pathogen components, such as vector density, biting rate, survival, vector competence and pathogen extrinsic incubation period all influence pathogen transmission. Interestingly, the mosquito gut-associated microbes can impact each of these components, and therefore ultimately modulate vectorial capacity. Promisingly, this expands the options available to exploit microbes for vector control by also targeting parameters that affect vectorial capacity. However, there are still many knowledge gaps in the biology of the mosquito – microbe symbiosis that need to be addressed in order to understand these interactions more thoroughly and exploit them efficiently. Here, we review current evidence of the impacts of the microbiome on aspects of vectorial capacity highlighting opportunities for novel vector control strategies and areas where further studies are required.