Direct laser writing three-dimensional nano-lithography is an established technique for manufacturing functional 3D micro- and nano-objects via non-linear absorption induced polymerization process. In this Chapter an underlying physical mechanisms taking place during nano-confined polymerization reaction, induced by tightly focused ultra-short laser pulses, are reviewed and discussed. The special attention is paid on the effects that directly impact structuring resolution and minimum achievable feature size. Analysis of possible photo-initiation mechanisms as contributing multi-photon absorption and avalanche ionization in pre-polymers under diverse exposure conditions (wavelength, pulse duration) is presented. Feasible structuring of pure (non-photosensitized) and functional nanoparticles doped polymer precursors is justified and benefits of such materials/structures for microoptics, photonics and cell scaffolds are highlighted. The influence of temperature effects (induced by writing process itself or determined by ambient conditions) on polymerization process, observed in different pre-polymers under diverse exposure regimes is outlined. The further adjustment of the structuring resolution is possible via precise control of light polarization and diffusion assisted radical quenching. The work is concluded with a brief outlook on future challenges and perspectives related to refinement of 3D ultra-fast laser lithography fabrication process in the means of application of diverse post-processing methods and research into novel photo-curable materials including inorganic ones.

With Direct Laser Writing (DLW) maturing in all aspects as a manufacturing technology a toolset for quality assurance must be developed. In this work we want to introduce a first of its kind test artifact. Test artifacts are standardized 3D models with specific geometric feature to evaluate the performance of writing parameters. Test artifacts are already common in other 3D additive manufacturing technologies e.g. Selective Laser Melting. The test artifact introduced in this work was developed in particular to accommodate 1) the high geometrical resolution of DLW structures and 2) the limited possibilities to examine the resulting structure. Geometric accuracy, surface adhesion as well as confocal raman spectroscopy results were considered when evaluating the design of the test artifact. We will explain the individual features and design considerations of our DLW test artifact. The difference between two slicers, Cura and 3DPoli, and the implications on measured feature sizes and the general shape is quantified. The measured geometries are used to derive a general design guide for a specific combination of photoresist, laser power and scanning speed and to analyse the geometric accuracy of a structure produced using these guidelines.

Direct femtosecond laser writing or inscription is a useful technique, and it has been 1 employed to engineer various materials in many applications including nonlinear photonic crystals, 2 which are of periodically patterned second-order nonlinearity to get and control the coherent light at 3 new frequencies. By manipulation of second-order nonlinearity, either erased or poled, quasi-phase 4 matching has been achieved in several crystals, especially three-dimensional nonlinear photonic 5 crystals have been originally proposed and proved to be truly three-dimensional. Here we shortly 6 review on the recent advances in the research field of nonlinear photonic crystals inscribed by 7 femtosecond laser. We also discuss some phenomena that not understood yet and the future possible research topics in this field.

We report an easy-to-implement device for SERS-based detection of various analytes dissolved in water droplets at trace concentrations. The device combines an analyte-enrichment system and SERS-active sensor site, both produced via inexpensive and high-performance direct fs-laser printing. Fabricated on a surface of water-repellent polytetrafluoroethylene substrate as an arrangement of micropillars, the analyte-enrichment system supports evaporating water droplet in the Cassie-Baxter superhydrophobic state, thus ensuring delivery of the dissolved analyte molecules towards the hydrophilic SERS-active site. The efficient pre-concentration of the analyte onto the sensor site based on densely-arranged spiky plasmonic nanotextures results in its subsequent label-free identification by means of SERS spectroscopy. Using the proposed device, we demonstrate reliable SERS-based fingerprinting of various analytes, including common organic dyes and medical drugs at ppb concentrations. The proposed device is believed to find applications in various areas, including label-free environmental monitoring, medical diagnostics, and forensics.

Luminescent carbon dots (CDs) were locally synthesized in the core of CYTOP fibers using IR femtosecond laser direct writing (FLDW), a one-step simple method serving as a post-treatment of the genuine fiber. This approach enables the creation of several types of modifications such as ellipsoid voids. The CDs and photoluminescence (PL) distribute at the periphery of the voids. The PL spectral properties were studied through Excitation Emission Matrix in the visible range and excitation/emission spectrum in UV/visible range. Our finding reveals the presence of at least 3 distinct luminescent species, facilitating a broad excitation range extending from UV to green, and light emission spanning from blue to red. The average laser power and dose influence the quantity and ratio of these luminescent CD species. Additionally, we measured the spatially resolved lifetime of the luminescence during and after the irradiation. We found longer lifetimes at the periphery of the laser-induced modified regions and shorter ones closer to the center, with a dominant lifetime ~ 2ns. Notably, unlike many other luminophores, these laser-induced CDs are insensitive to oxygen, enhancing their potential for display or data storage applications.

In this project, four of fibers Bragg gratings were fabricated by injecting different volumes of liquids (star line Glass Mechanix optical adhesive material, olive oil diluted with ethanol) into the hollow core fiber. The amplitude splitting interferometric technique with a high resolution specially designed translation stage was used for the fabrication process. The fabrication was done using ultraviolet laser operated at wavelength 405nm. The fabricated Bragg length of the four fibers is equal to 3.8 cm. The results presented fiber Bragg grating (FBG) with successful fabrication at 653.3 nm Bragg reflected wavelength.

In this paper, we present a preliminary study and conceptual idea concerning 3D printing water-sensitive glass by exemplifying with a borosilicate glass with high alkali and alkaline oxide contents using direct ink writing. The investigated material was prepared in the form of a glass frit, which was further ground in order to obtain a fine powder of desired particle size distribution. In a following step, inks were prepared by mixing the fine glass powder with Pluoronic F-127 hydrogel. The acquired pastes were rheologically characterized and printed using a Robocasting device. DSC experiments were performed for base materials and the obtained green bodies. After sintering, SEM and XRD analyses were carried out in order to examine microstructure and the eventual presence of crystalline phase inclusions. Results confirmed that obtained inks exhibit stable rheological properties despite the propensity of glass to undergo hydrolysis and could be adjusted to desirable values for 3D printing. No additional phase was observed, supporting the suitability of the designed technology for the production of water sensitive glass inks. SEM micrographs of the sintered samples revealed the presence of closed porosity, which may be the main reason of light scattering.

Electronic designers nowadays are facing two challenging demands for various applications: miniaturization and increased functionality. To satisfy these seemingly opposed requirements, reducing the number of mounted components—and thus solder joints—in PCB designs becomes an attractive approach by directly printing passive components such as embedded resistors into the circuit. This approach can also potentially increase the reliability, such as “mean time between failures” (MTBF), while reducing the circuit board size. With its unique capabilities for non-contact precision material deposition, the Aerosol Jet® direct-write technology has been enabling additive manufacturing of fine-feature electronics conformally onto flexible substrates of complicated shapes. The CAD/CAM controlled relative motions between substrate and print head allows convenient adjustment of the pattern and pile height of deposited material at a given ink volumetric deposition rate. To date in the printed electronics industry, additively printing embedded polymer-thick-film (PTF) resistors has mostly been done with screen printing using carbon-based paste inks. Here we demonstrate results of Aerosol Jet® printed PTF resistors of resistance values ranging from ~50 W to > 1 kW, adjustable (among several variable parameters) by the number of stacked layers (or print passes with each pass depositing a fixed amount of ink) between contact pads of around 1 mm apart with footprint line typically < 0.3 mm. In principle, any ink material that can be atomized into fine droplets of 1 to 5 microns can be printed with the Aerosol Jet® system. However, the print quality such as line edge cleanliness can significantly influenced by ink rheology which involves solvent volatility, solids loading, and so on. Our atomizable carbon ink was made by simply diluting a screen printing paste with a compatible solvent of reasonable volatility, which can be cured at temperatures below 200 ^oC. We show that Aerosol Jet® printed overlapping lines can be stacked to large pile height (to reduce the resistance value) without significant increase of line width, which enables fabricating embedded resistors with adjustable resistance values in a limited footprint space.

Laser in situ keratomileusis (LASIK) is the gold standard in the surgical correction of refractive errors on the cornea. It entails the creation of a superficial hinged corneal flap by a femtosecond laser, ablation of the underlying stromal bed by an excimer laser, and reposition of the flap. The corneal flap can be build in a 2-dimension (2D) fashion with tapered edges, or in a 3-dimension (3D) fashion, with angled sidecut. The latter reduces the risk of flap dislocation and infiltration of epithelial cells. This retrospective study compares with optical coherence tomography 3D and 2D flaps, and respective intra- and early post-operative complications. Four hundred consecutive eyes were included, 200 for each group. In the 3D group, the mean edge angle was 92°. The procedure was in average 5.2 seconds slower in the 3D group (p=0). Non visually significant flap folds were found in 13 eyes of the 2D group and in 7 eyes of the 3D group (p= 0.17). An intracorneal opaque bubble layer induced by laser photodisruption was more commonly observed in the 3D group (9 eyes vs. 2; p=0.03). In conclusion, the creation of a LASIK flap by a 3D-femtosecond laser cut was safe and effective.

This article utilizes the Canny edge extraction algorithm based on contour curvature and the cross-correlation template matching algorithm to extensively study the impact of high-repetition-rate CO2 pulsed Laser on the target extraction and tracking performance of the infrared imaging detector. It establishes a quantified dazzling pattern for lasers on infrared imaging systems. By conducting laser dazzling and damage experiments, a detailed analysis of the normalized correlation between target and dazzling images is performed to quantitatively describe laser dazzling effects. Simultaneously, an evaluation system, including target distance and laser power evaluation factors, is established to determine the dazzling level and whether the target is recognizable. The research results reveal that laser power and target position are crucial factors affecting the detection performance of infrared imaging-guided weapon systems under laser dazzling. Different laser powers are required to successfully interfere with the recognition algorithm of infrared imaging-guided weapons at different distances. And laser dazzling will produce a lot of false edge information, which seriously affects the performance of pattern recognition algorithm. In laser damage experiments, the detector experienced functional damage, with a quarter of the image displaying as completely black. The energy density threshold required for functional damage to the detector is approximately 3 J/cm2. The dazzling assessment conclusions also apply to evaluating damage results. Finally, the proposed evaluation formula aligns with experimental results, objectively reflecting the actual impact of laser dazzling on the target extraction and tracking performance of infrared imaging systems. This study provides an in-depth and accurate analysis for understanding the influence of lasers on the performance of infrared imaging-guided weapons.

In the present work, the state of the art of the most common additive manufacturing (AM) technologies used for the manufacturing of complex shape structures of graphene-based ceramic nanocomposites, ceramic and graphene-based parts is explained. A brief overview of the AM processes for ceramic, which are grouped by the type of feedstock used in each technology, is presented. The main technical factors that affect the quality of the final product were reviewed. The AM processes used for 3D printing of graphene-based materials are described in more detail; moreover, some studies in a wide range of applications related to these AM techniques are cited. Furthermore, different feedstock formulations and their corresponding rheological behaviour were explained. Additionally, the most important works about the fabrication of composites using graphene-based ceramic pastes by Direct Ink Writing (DIW) are disclosed in detail and illustrated with representative examples. Various examples of the most relevant approaches for the manufacturing of graphene-based ceramic nanocomposites by DIW are provided.

Crystalline silver thin layers were obtained by high-energy pulsed laser ablation without heating of the deposition substrate. The fluid Plateau-Rayleigh (PRI), Rayleigh – Taylor (RTI) and Richtmyer – Meshkov (RMI) instabilities, as well as crown splash induced during pulsed laser deposition (PLD) in high energy regime, resulting in ring and pearl shaped structures, offer the benefit of increased sorption surface. These morphological structures obtained for the silver thin layers make them of interest for catalytic applications. The study presented with this work addresses both the fundamental and applied issues on the morphological structures obtained for the silver thin layer and their catalytic function in organic processes. In this sense, the catalytic action of the thin silver layer was highlighted by modifications of the Reactive Blue 21 dye (C.I.) in aqueous solution with sodium bicarbonate. Specific investigations and analyzes were carried out by electron microscopy and elemental analysis (SEM-EDX), atomic force microscopy (AFM) and profilometry, mass spectrometry, ablation plasma diagnosis, diffractograms (XRD), as well as IR spectroscopy (FTIR). In addition to the experimental investigation and analyzes, simulation of the ionization energy threshold was conducted in COMSOL for complementary evaluation on the involved processes and phenomena.

High-power laser facilities necessitate predicting incremental damage to final optics to identify evolving damage trends. In this study, we propose a surface damage detection method utilizing image segmentation employing ResNet-18, and a damage area estimation network employing U-Net++. Paired sets of online and offline images of optics obtained from a large laser facility is used to train the network. The trends of varying damage could be identified by incorporating additional experimental parameters. A key advantage of the proposed method is that the network can be trained end-to-end on small samples, eliminating the need for manual labeling or feature extraction. The software developed based on these models can facilitate the daily inspection and maintenance of optics in large laser facilities.

The present work investigates primarily the morphology evolution of the body-centered-cubic (BCC)/B2 phases in AlxNiCoFeCr high-entropy alloys (HEAs) with increasing Al content, which has been neglected so far. There exist two types of microscopic morphologies of BCC and B2 phases in this HEA series: one is the weave-like morphology induced by the spinodal decomposition, and the other is the microstructure of a spherical disordered BCC precipitation on the ordered B2 matrix that appears in HEAs with a much higher Al content. The shape of coherent precipitates is found to be closely related to the lattice misfit between BCC and B2 phases, which is sensitive to Al. The mechanical properties, including the compressive yielding strength and microhardness of the AlxNiCoFeCr HEAs, are also discussed in light of the concept of the valence electron concentration (VEC).

The aim of this work is to study the phase transformations, microstructures and mechanical properties of the martensitic stainless steel (MSS) 410 deposits produced by laser powder-directed energy deposition (LP-DED) additive manufacturing. The LP-DED MSS 410 deposits underwent the post heat treatment in austenitizing at 980℃ for 3hrs and followed by different tempering treatment at the temperatures of 250, 600, and 750℃ for 5hrs, respectively. The analyses of phase transformations and microstructural evolutions of LP-DED MSS 410 were carried out using X-ray diffraction, SEM-EDS, and EBSD. Vickers hardness and tensile strength properties were also measured to analyze the effects of the different tempering heat treatments. It reveals that as-built MSS 410 has very fine lath martensite and high hardness of about 480HV1.0 and tensile strength of about 1280 MPa, but elongation was very lower than the post heat treated ones. Precipitations of chromium carbide (Cr23C6) were most commonly observed at the grain boundaries and the entire matrix at the tempering temperatures of 600℃ and 750℃. In general, the tensile strengths de-creased from 1381MPa to 688MPa as tempering temperatures increased up to 750℃ from 250℃. Additionally, as the tempering temperature increased, the chromium carbide and tempered mar-tensite structures became coarser.

We demonstrate a multi-purpose plasmonic sensor based on nanovoid array fabricated via inexpensive and highly reproducible direct femtosecond laser patterning of thin glass-supported Au films. The proposed nanovoid array exhibits near-IR surface plasmon (SP) resonances, which can be excited under normal incidence and optimised for specific application by tailoring array periodicity as well as nanovoid geometric shape. Fabricated SP sensor offers competitive sensitivity of about 1600 nm/RIU at a figure of merit of 12 in bulk refractive index tests, as well as allows for identification of gases and ultra-thin analyte layers making the sensor particularly useful for common bioassay experiments. Moreover, isolated nanovoids support strong electromagnetic field enhancement at lattice SP resonance wavelength, allowing for label-free molecular identification via surface-enhanced vibration spectroscopy.

The integrated DC-DC converter is appropriate for use in many domains, namely, display, cellular, and portable applications. This paper presents an integrated monolithic voltage-mode DC-DC boost converter with a low-power control circuit. The driver circuit requires an integrated converter to power up a digital logic circuit and converts the unregulated DC input to the controlled DC output at the desired voltage level. It is the integration of both power switches and control circuitry within the same CMOS technology to buck down and boost voltages using a switch mode regulator. In order to increase power efficiency in the DC-DC boost converter that provides low-power operation with a small chip size, a low-voltage operation is applied to the unique circuit characteristic. The operational transconductance amplifier(OTA), comparator, and oscillator in the control circuit are designed with the supply voltage of 3.3V and the operating frequency of 5.5 MHz. A compensator is used to create a pole that has sufficient phase margin for high stability. The DC- DC boost converter is measured in both experiment and simulation. Testing of the proposed circuit on the 0.35μm CMOS process shows that the output transient time of the amplifier can be controlled within of 7μsec and the output voltage is accurately controlled with a ripple ratio of 3%.

Despite available global efforts and funding, Tuberculosis (TB) continues to affect a considerable number of patients worldwide. Policy makers and stakeholders set clear goals to reduce TB incidence and mortality, but the emergence of multidrug-resistant TB (MDR-TB) and extensively drug-resistant TB (XDR-TB) complicate the reach of these goals. Drug-resistance TB needs to be diagnosed rapidly and accurately to effectively treat patients, prevent the transmission of MDR-TB, minimise mortality, reduce treatment costs and avoid unnecessary hospitalisations. In this narrative review, we provide a comprehensive overview of laboratory methods for detecting drug resistance in MTB, focusing on phenotypic, molecular and other drug susceptibility testing (DST) techniques. We found a large variety of methods used, with the BACTEC MGIT 960 being the most common phenotypic DST and the Xpert MTB/RIF being the most common molecular DST. We emphasise the importance of integrating phenotypic and molecular DST to address issues like resistance to new drugs, heteroresistance, mixed infections and low-level resistance mutations. Notably, most of the analysed studies adhered to the outdated definition of XDR-TB and did not consider the pre-XDR definition, thus posing challenges in aligning diagnostic methods with the current landscape of TB resistance.

Self-driving vehicles demand efficient and reliable depth sensing technologies. Lidar, with its capacity for long-distance, high-precision measurement, is a crucial component in this pursuit. However, conventional mechanical scanning implementations suffer from reliability, cost, and frame rate limitations. Solid-state lidar solutions have emerged as a promising alternative, but the vast amount of photon data processed and stored using conventional direct time-of-flight (dToF) prevents long-distance sensing unless power-intensive partial histogram approaches are used. In this paper, we introduce a groundbreaking ‘guided’ dToF approach, harnessing external guidance from other onboard sensors to narrow down the depth search space for a power and data-efficient solution. This approach centers around a dToF sensor in-which the exposed time widow of independent pixels can be dynamically adjusted. We utilize a 64-by-32 macropixel dToF sensor and a pair of vision cameras to provide the guiding depth estimates. Our demonstrator captures a dynamic outdoor scene at 3 fps with distances up 75 m. Compared to a conventional full histogram approach, on-chip data is reduced by over 25 times, while the total laser cycles in each frame are reduced by at least 6 times compared to any partial histogram approach. The capability of guided dToF to mitigate multipath reflections is also demonstrated. For self-driving vehicles where a wealth of sensor data is already available, guided dToF opens new possibilities for efficient solid-state lidar.

A portable laser photoacoustic sensor based on a Field-Programmable Gate Array (FPGA) is reported for methane detection. A tunable DFB diode laser in the 1654 nm wavelength range is used as an excitation source. The photoacoustic signal processing was implemented by a FPGA device. A small resonant photoacoustic cell is designed. The minimum detection limit (1σ) of 10 ppm for methane (CH₄) is demonstrated.

Metal 3D printing technology is a promising manufacturing method. The quality of the printed product can pass for mechanical application, if the anisotropy of the microstructure, imperfections, deformation, and residual stress of the printed sample could be lower than the appropriate level or if they are fully illuminated. Thermal stress is one of the significant reasons for deformation in the 3D printed samples. Thermal stresses are the direct consequence of the local temperature gradient. In this research, the effect of the temperature printer’s chamber (from room temperature to 900 C) was studied on thermal stress and subsequent total deformation in the printed sample. The printed sample is a six-layers-printed walk, which could be considered as a building block of other complex shapes and give us inside about deformation. The computational results show a meaningful reduction in thermal stress and deformation at the higher temperature of the printer’s chamber. The lower final deformation of the printed sample is an important subject, especially for samples with complex shapes.

Chromium (Cr) metal has garnered significant attention in alloy systems owing to its exceptional properties, such as high melting point, low density, and superior oxidation and corrosion resistance. However, its processing capabilities are hindered by the high Ductile-Brittle Transition Temperature (DBTT). Recently, powder bed fusion-laser beam for metals (PBF-LB/M) has emerged as a promising technique, offering the fabrication of net shapes and precise control over crystallographic texture. Nevertheless, research investigating the mechanism underlying crystallographic texture development in pure Cr via PBF-LB/M still needs to be conducted. This study explores the impact of scan speed on relative density and crystallographic texture. At the optimal scan speed, an increase in grain size attributed to epitaxial growth was observed, resulting in the formation of cubic texture. Consequently, a reduction in High Angle Grain Boundaries (HAGB) was achieved, suppressing defects such as cracks and enhancing relative density up to 98.1%. Furthermore, with increasing densification, Vickers hardness also exhibited a corresponding increase. These findings underscore the efficacy of PBF-LB/M for processing metals with high DBTT properties.

Large-area nanostructuring of glasses using intense laser beam remains a difficult task due to the extreme non-linear absorption of the laser energy by the material. Precise optimization of the process parameters is essential for fabricating nanostructures with large area coverage. In this study, we report the findings on creating high spatial frequency LIPSS (HSFL) on borosilicate glass through direct laser writing, using a femtosecond laser with a wavelength λ = 800 nm, pulse duration τ = 35 fs, and repetition frequency frep = 1 kHz. The orientation of the HSFL was found to be parallel to the electric field vector. We measured the single pulse ablation threshold (Fth=3.87±0.26 J/cm2) and incubation factor (S=0.68±0.03) of Borosilicate glasses for precise control for large area surface structuring. Single-spot experiments indicate that uniform LIPSS formation is limited by melt formation inside the irradiated area for higher fluence and a larger number of irradiated laser pulses. The orientation of the scan axis with the laser beam polarization is found to be significantly influencing the uniformity of the large area processing. We found that the orientation of the scan axis with the laser beam polarization significantly affects the uniformity of large-area processing, with redeposition and melt formation being higher when the scan axis is perpendicular to the laser beam polarization. Large-area processing of the borosilicate glass surface is done by line-by-line scanning over the surface with a scan orientation parallel to the laser beam polarization. The optical characterization reveals that the transmittance and reflectance of the borosilicate glass decreased significantly after processing. Also, the wettability of the surface has been changed from hydrophilic to super hydrophilic after processing. These chemical contamination-free and uniformly distributed structures have potential applications in optics, microfluidics, photovoltaics, and biomaterials.

Aim/Purpose: This study aims to assess the influence of integrating ChatGPT on enhancing the academic writing performance and engagement of English as a Foreign Language (EFL) undergraduate students at Delhi, India, who are enrolled in Academic Writing during the first semester of the academic year 2024/2025. Given the unique challenges within the Indian undergraduate education system, innovative technological interventions are essential to improve writing skills and increase engagement among EFL learners.

Background: this interventional pilot study aimed to evaluate the short-term (3 years) efficacy of focal laser ablation (FLA) in treating the index lesion of low-intermediate risk prostate cancer, along with assessing the safety of the procedure (ClinicalTrials.gov ID NCT04045756). Methods: forty patients aged between 46 and 86 with histologically proven organ-confined prostate cancer and low to intermediate progression risk were included. FLA was performed under percutaneous fusion magnetic resonance/ultrasound guidance in a Day Hospital setting under local anesthesia. Patients underwent regular clinical assessments, PSA measurements, post-procedure MRI scans, and biopsies at 36 months or if positive findings were detected earlier. Statistical analyses were conducted to assess trends in PSA levels and cavity dimensions over time. Results: forty patients were initially included, with 15 lost to follow-up. At 36 months, a mean PSA reduction of 60% was observed, and 80% of MRI scans showed no signs of in-field clinically significant residual/recurrent cancer. Biopsies at 36 months revealed no malignant findings in 20 patients. No deterioration in sexual function or urinary symptoms was recorded. Conclusions: FLA appears to be safe, feasible and effective in the index lesion treatment of low-intermediate risk prostate cancer, with a high rate of tumor eradication and preservation of quality of life.

Abstract Introduction: In the last thirty years, brain neuromodulation techniques have been used as an alternative to pharmacological treatment of neurological disorders. Parkinson's disease (PD) is a neurodegenerative disorder leading to bradykinesia, rest tremor, postural changes, and non-motor symptoms such as depression, anxiety, sleep disorders, pain, and cognitive decline that compromises executive functions (EFs), responsible for the orderly execution of behaviors and tasks of daily life and intentional and directed actions. To this date, a few studies with transcranial direct current stimulation (tDCS) have shown beneficial effects in PD patients concerning specific motor and non-motor symptoms, targeting the motor cortex and/or prefrontal regions. Objective: The main objective of this study was to evaluate the effects of left prefrontal tDCS across a broad spectrum of motor and non-motor symptoms of PD using established validated scales. Method: Single-blind randomized clinical trial with 18 volunteers with PD, aged between 45 and 80 years (66.1 ± 9.65), who met inclusion and exclusion criteria. Participants were submitted to assessments of motor and non-motor functions employing psychometric scales and tests to evaluate EFs and were randomly divided into two groups: control (sham stimulation) and experimental (active stimulation). All participants were involved in three separate tDCS sessions. The anode was positioned over the left dorsolateral prefrontal cortex and the cathode over the right supraorbital region, with a direct current intensity of 2mA, lasting 20 minutes. At the end of the three sessions, all participants were reassessed. Results: Significant effects of tDCS on non-motor functions were observed for cognition (verbal fluency of actions, clock copy test, appointment by visual confrontation, and verbal memory with immediate free recall) and subjective assessment of sleep quality (overall restlessness and discomfort in the arms and legs at night, leg and arm cramps at night and distressing dreams). There was also an improvement in the rate of errors and successes for congruent and incongruent stimuli of the Stroop Test. The beneficial effects on motor function were decreased rigidity, improved gait, and greater agility in the finger-tapping test. Conclusion: Three tDCS sessions showed positive results for participants with PD, producing significant improvements in various motor and non-motor functions, including sleep quality, cognition, and EFs. Additionally, the present results indicate that tDCS neuromodulation of the left dorsolateral prefrontal cortex region is feasible, safe, and provides significant objective benefits for PD patients.

Aim: To evaluate the panmacular subthreshold micropulse laser treatment results among patients with central serous chorioretinopathy (CSC) and their correlation with functional and morphological parameters. Material and methods: The examined group included 10 non-treated and 41 treated patients with acute, recurrent, and chronic CSC (13 F, 38 M, mean age 44.11±6.5) and 14 healthy controls (6 F, 8 M, mean age 45±9.3). The BCVA examination, ophthalmoscopy, microp-erimetry, angio-OCT and OCT were performed. The medical history regarding chronic general disorders and known risk factors were recorded. Results: Complete resorption of SRF was obtained in 100% aCSC, 86.66% cCSC, and 63.63% r CSC. BCVA and RetSens significantly improved most of the patients treated in aCSC. The lowest BCVA and RetSens, but the largest pachyvessel and disease duration, were found in rCSC. A strong negative correlation between final BCVA and disease duration was found. No patient demonstrated laser lesions following treatment. Conclusions: The panmacular MPLT therapy leads to long-term enhancement of functional and morphological parameters in all CSC patients. The acute CSC patients showed the most significant improvement. The procedure is safe and could be considered a preferred treatment option for all active CSC cases. Timely treatment is crucial for beneficial outcomes.

Background: The validation of laser usage during laparoscopic procedures, notably by Camran Nezhat in the late 1980s, has been significant. Lasers offer precision and depth control in tissue vaporization without bleeding. Surgical intervention remains central in managing endometrio-sis-associated pain and infertility, especially for patients unresponsive to hormonal therapy. Methods: This retrospective cohort study included 200 patients with SPE who underwent laparo-scopic laser vaporization. Surgery was performed using a CO2 laser, and histological confirma-tion of endometriosis was obtained for all cases. Pain scores and SF-36 questionnaire domains were assessed preoperatively and postoperatively. Fertility outcomes were evaluated among pa-tients desiring pregnancy. Results: Significant improvements in pain score and SF-36 questionnaire domains were ob-served postoperatively (p-value

Precise individual tree or sample-based inventories derived from 3D point cloud data of mobile laser scanning can improve our comprehensive understanding of the structure, function, resilience, biodiversity, and ecosystem services of urban forests. This study assessed the performance of a hand-held laser scanning system for the extraction of tree position, diameter at breast height (DBH) and tree height (H) in an urban area. A total of 2083 trees of 13 species from 34 plots were analyzed. The results showed that the registration of tree positions using ground control points (GCPs) demonstrated high accuracy, with errors consistently below 0.4 m, except for a few instances. The extraction accuracy of DBH for all trees and individual species remained consistently high, with a total root mean square error (RMSE) of 2.06 cm (6.89%) and a bias of 0.62 cm (2.07%). Notably, broad-leaved trees outperformed coniferous trees, with RMSE and bias values of 1.86 cm (6%) and 0.76 cm (2.46%) compared to 2.54 cm (9.46%) and 0.23 cm (0.84%). Tree height extraction accuracy varied significantly among different species, with R2 values ranging from 0.65 to 0.92. Generally, both DBH and height were underestimated. Linear mixed effects models (LME) were applied to evaluate factors affecting the performance of HLS with the plot as a random factor. LME analysis revealed that plant type and terrain significantly influenced the accuracy of DBH and H derived from HLS data. Other fixed factors of plot area, tree density and trajectory length didn’t have significance. With a large sample size, we concluded that the HLS demonstrated sufficient accuracy in extracting individual tree parameters in urban forests.

A large core size and bending resistance are very important properties of mid-infrared energy transfer fibers, but large core sizes usually lead to a deterioration of bending properties. A negative-curvature nested node-free anti-resonant hollow-core fiber (AR-HCF) based on quartz is proposed. It was made by adding a nested layer to a previous AR-HCF design to provide an additional anti-resonance region while keeping the gap between adjacent tubes strictly correlated to the core diameter to produce a node-free structure. These features improve the fiber’s bending resistance while achieving a larger core diameter. The simulation results show that the radial air-glass anti-resonant layer is increased by the introduction of the nested anti-resonant tube, and the weak interference overlap between the fiber core and the cladding mode is reduced, so the fiber core’s limiting loss and the sensitivity to bending are effectively reduced. When the capillary wall thickness t of the fiber is 0.71 μm, the core diameter D is 70 μm, the ratio of the inner diameter of the cladding capillary to the core diameter d/D is 0.62, and the diameter of the nested tube is d0=29 μm, the fiber has a lower limiting loss at the wavelength of 2.79 μm, and the limiting loss is 3.28×10-4 dB/m. At the same time, the optimized structure also has good bending resistance. When the bending radius is 30 mm, the bending loss is only 4.72×10-2 dB/m. To our knowledge, this is the first research to achieve an anti-bending low-loss micro-structure hollow fiber with a bending radius of less than 30 mm in the 2.79 μm band. An anti-bending low-loss anti-resonant hollow-core fiber with this structure constitutes a reliable choice for the light guiding system of a 2.79 μm band erbium laser therapy instrument.

To enhance the applicability of dual-phase high-entropy alloys (HEAs) like Fe32Cr33Ni29Al3Ti3, fabricated via selective laser melting (SLM), a focus on improving their mechanical properties is essential. As part of this effort, heat treatment was explored. This study compares the microstructure and mechanical properties of the as-printed sample with those cooled in water after undergoing heat treatment at temperatures ranging from 1000 to 1200 ℃ for 1 hour. Both pre- and post-treatment samples reveal a dual-phase microstructure comprising FCC and BCC phases. Although heat treatment led to a reduction in tensile and yield strength, it significantly increased ductility compared to the as-printed sample. This strength-ductility trade-off is related to changes in grain sizes with ultrafine grains enhancing strength and micron grains optimizing ductility, also the influence of the content of FCC/BCC phases and dislocation density. In particular, the sample heat-treated at 1000 °C for 1 hour and then water-cooled exhibited a better combination of strength and ductility, a yield strength of 790 MPa, and an elongation of 13%. This research offers innovative perspectives on crafting dual-phase HEA of Fe32Cr33Ni29Al3Ti3, allowing for tailorable microstructure and mechanical properties through a synergistic approach involving SLM and heat treatment.

An easy to implement and cost-effective Fiber Bragg Grating (FBG) sensor interrogation technique based on a ring Erbium-Doped Fiber Laser (EDFL) topology is proposed and experimentally assessed. The FBG sensor is part of the EDFL cavity and must have a central wavelength located within the linear region of the EDF’s amplified spontaneous emission (ASE) spectrum which occurs between 1530 and 1540nm. In this manner, the wavelength-encoded response of the FBG under strain is converted to a linear variation of the laser output power, removing the need for spectrum analysis as well as any limitations from the use of external edge-filtering components. In addition, the laser linewidth is significantly reduced with respect to the FBG bandwidth thus improving the resolution of the system, whereas its sensitivity can be controlled through the pumping power. The performance of the system has been characterized by modeling and experiments for EDF's with different lengths, doping concentrations and pumping power levels. The influence of mode-hopping in the laser cavity on the resolution and accuracy of the system has also been investigated.

The growing usage of Generative AI tools in scientific writing requires a critical examination of their benefits and challenges. This literature review is aimed at comprehensively analyzing current empirical research articles focused on the application of Generative AI in scientific writing. The Google Scholar database was used to search for the literature. The following keywords were used: "Generative AI" and "academic writing", "LLM" (Large Language Models) and "academic writing", "Generative AI" and "Scientific writing", and "ChatGPT" and "Scientific Writing". The search was restricted to articles published between January 1, 2023, and April 30, 2024. 15 articles were selected as appropriate for the study and analyzed. It was found that, thus far, ChatGPT is the most exploited tool in the studies. AI tools such as Bard (Gemini), Bing, Claude2, and Elicit were also tested. The benefits of Generative AI usage in scientific writing were found to be omnipresent. It can aid in the generation of structured abstracts, titles, introductions, literature reviews, and conclusions of a scientific article. Generative AI also makes writing more efficient and time-saving. Its capabilities in improving language and proofreading are well-established. However, the generation of inaccurate content and references by current commercially available LLMs poses a serious problem. The lack of critical thinking and tendency to produce non-original content are significant drawbacks. Generative AI should be employed with human oversight, serving as an assistant rather than a replacement. Transparency in AI usage in scientific writing is essential, along with the necessity for proper legal regulation.

Day by day, the share of renewable energy-based power plants such as offshore wind farms and photovoltaic power plants, in the present-day power systems is escalating. Nevertheless, most of these power-producing facilities have been located quite far away from the load centers. At this stage, HVDC power systems provide satisfactory options due to qualities such as reduced line losses, substantial controllability, and environmental advantages. Nevertheless, unique converter designs are required to combine asynchronous HVDC networks with each other and with already existing high voltage alternating current (HVAC) networks. In this study, based on the above special cases, a unique DC-DC modular multilevel converter (MMC) architecture is presented that provides an excellent solution for both integrating modern asynchronous HVDC networks and integrating these modern HVDC power systems with existing asynchronous HVAC power systems. The mathematical analysis of the recommended DC-DC MMC design has been examined in detail and the power transfer between two asynchronous power grids has been realized in a simulation environment. Efficient bilateral power transmission has been made achievable by the control system. The recommended DC-DC MMC topology has shown to be a highly successful approach, in the interconnection of HVDC power systems, according to the simulation results.

Antler is the fastest growing tissue. Because is based on proto-oncogenes, to avoid the risk of cancer, antlers evolved strong anticancer mechanisms, and thus its extract (DVA) is effective also against the few human tumours studied so far. We assessed whether DVA is a general anticancer compound testing direct effects in cells of different tumours: glioblastoma (GBM), colorectal and breast cancer, and leukaemia. DVA reduced viability of tumour but not healthy cells. Mobility decreased at least at the longest test (72 h). Intraperitoneal/oral 200 mg DVA/kg administration in GBM xenograft mice for 28 d reduced tumour weight 66.3% and 61.4% respectively, and also spleen weight. In addition, tumours treated with DVA showed symptoms of liquefactive necrosis. Serum cytokines showed DVA up-regulated factors related with tumour fighting and down-regulated those related with inducing immune tolerance to the tumour. DVA shows general anticancer effects in the lines tested and, in GBM mice, also strong indirect effects apparently mediated by the immune system.

Objective: To evaluate the direct costs of treating patients with neuromyelitis optica spectrum disorders (NMOSD) in outpatient care, from a hospital and Unified Health System (SUS) perspective. Methods: Observational study with data collection by microfunding, carried out with patients diagnosed with neuromyelitis optics, treated at a university hospital, in the city of Rio de Janeiro. Mann-Whitney tests were performed to measure cost differences between patient groups by disease severity and analysis perspective. Results: Nine individuals with a median age of 48 years (IQR 30 - 59 years) were included. The median total costs for patients with greater severity from the perspective of the SUS and the hospital were R$ 21,638.22 (IIQ: R$ 15,614.63; R$ 25,985.32) and R$ 32,094.11 (IIQ: R$ 25,610 .60; R$ 38,617.25) respectively. For patients with moderate severity the median was R$ 7,339.85 (IIQ: R$ 6,235.45; R$ 11,912.05) from the SUS perspective and R$ 11,505.80 (IIQ: R$ 7,339.85; R$ 22,424.76) from the perspective of the hospital, where the use of medications had a major impact. Conclusion: The main cost drivers were medicines, especially those used off-label, and procedures.

Artificial Intelligence (AI) is a breakthrough technology that has been widely applied in many fields and its use in pharmacy is also gaining increasing attentions. Recently, ChatGPT, a newly developed virtual assistant and large language model, is showing strong ability in writing, which makes it a potential tool for review writing. Here in our study, we employ the public available ChatGPT and try to instruct it to generate a mini review on the topic of “lipid-based drug delivery systems” by conversation. Our results showed that ChatGPT can give reasonable outline for this topic and give seemingly sentences with concluding wording, which can give useful information to the readers. However, the accuracy and consistence of the review are not fully guaranteed and there is lack of reliable citations. Therefore, it is concluded that ChatGPT can only give general knowledge on the selected topic, but not capable of giving in-depth discussion. The generated review article can be a useful but occasionally unprecise electronic encyclopedia instead of rigorous scientific literature, which can give benefit for pharmaceutical education and interchange to some extent.

Every scholarly journal's ultimate objective and purpose is to publish high-quality work. This article discusses the adoption of a worldwide virtual writing camp as an alternate approach given by journal editorial boards to increase the quality of prospective authors during the current Sars-Cov-2 pandemic, when face-to-face meetings are impractical. A virtually entire training program was designed for those interested in submitting their manuscript to journals but lack the necessary understanding and expertise to write a so-called high-quality paper. This strategy consisted of nine phases and required around three months to complete. By the end of the camp, participants should have written one or more papers that were ready to send and submit.

A space charge density wireless measurement system based on the idea of distributed measurement is proposed for collecting and monitoring the space charge density in an ultra-high-voltage direct-current (UHVDC) environment. The proposed system architecture is composed of a number of wireless nodes connected with space charge density sensors and a base station. The space charge density sensor based on atmospheric ion counter method is elaborated and developed, and the ARM microprocessor and Zigbee radio frequency module are applied. The wireless network communication quality and the relationship between energy consumption and transmission distance in the complicated electromagnetic environment is tested. Based on the experimental results, the proposed measurement system demonstrates that it can adapt to the complex electromagnetic environment under the UHVDC transmission lines and can accurately measure the space charge density.

The laser sintering process and modification of electrophoretic deposition (EPD) YSZ coatings on YSZ air plasma sprayed thermal barrier coatings (TBCs) were investigated. Ni-based superalloy was plasma sprayed using yttria-stabilized zirconia (YSZ) to perform thermal barrier coating with 400 μm thickness. The electrophoretic deposition (EPD) technique was used for depositing nanopowder of YSZ on the surface of YSZ TBCs. In this study, a technology of direct sintering the green EPD layer by laser beam was carried out. The best conditions of deposition YSZ overlay coating using DC current were obtained with applied voltage 40 V, deposition time 5 min, and suspension concentration 10 g/l. Iodine was added to the solutions as the stabilizing agent. To overcome the disadvantages of high sintering temperatures, laser sintering was taken as a new approach. Microstructures for all specimens were studied using Field Emission Scanning Electron Microscopy (FESEM) with EDS analysis. Surface roughness was investigated using AFM analysis and central line average (CLA). The results indicated that the morphology after the direct laser sintering of the EPD layer has a fine and controllable grain size, high hardness, and low roughness. Which is better than the direct laser on plasma-sprayed coatings.

Based on PVDF (piezoelectric sensing techniques), this paper attempts to study the propagation law of shock waves in brittle materials during the process of three-wavelength laser irradiation of polysilicon, and discusses the formation mechanism of thermal shock failure. The experimental results show that the vapor pressure effect and the plasma pressure effect in the process of pulsed laser irradiation lead to the splashing of high temperature and high density melt. With the decrease of the laser wavelength, the laser breakdown threshold decreases and the shock wave is weakened. Because of pressure effect of the laser shock, the brittle fracture zone is at the edge of the irradiated area. The surface tension gradient and surface shear wave caused by the surface wave are the result of coherent coupling between optical and thermodynamics. The average propagation velocity of laser shock wave in polysilicon is 8.47×103m/s, and the experiment has reached the conclusion that the laser shock wave pressure peak exponentially distributes attenuation in the polysilicon.

Delve into the ebb and flow of human ingenuity as the researcher traces the evolution of writing from papyrus to pixels. Discover how humble instruments like quill pens and typewriters have propelled human into the digital frontier, forever reshaping the art of expression in the modern age. This article examines the evolution of writing tools from traditional pen and paper to digital writing in the modern age. It explores the development of writing materials such as papyrus, parchment, and paper, as well as the invention of writing tools including quill pens, fountain pens, and typewriters. The rise of digital writing tools, including word processing software and smartphones, is also discussed, along with their benefits such as increased efficiency and productivity, enhanced collaboration and sharing capabilities, and greater accessibility and flexibility. However, the article also highlights the challenges of writing in the digital age, including the impact of digital distractions on writing focus and quality, the issue of online plagiarism and copyright infringement, and the potential loss of traditional writing skills. The article concludes with recommendations for educators, school administrators, students, and researchers to strike a balance between digital and traditional writing practices, to embrace digital writing tools while preserving traditional writing skills, and to understand the importance of the evolution of writing. The theoretical frameworks of Social Construction of Technology (SCOT) Theory, Media Ecology Theory, and Activity Theory are also discussed in relation to the evolution of writing tools. Overall, this article provides valuable insights into the history, benefits, and challenges of writing in the digital age, as well as suggestions for navigating the future of writing and its tools.

Residual stress (RS) is the most challenging problem in metal additive manufacturing (AM) since the build-up of high tensile RS may influence the fatigue life, corrosion resistance, crack initiation, and failure of the additively manufactured components. While tensile RS is inherent in all the AM processes, fast and accurate prediction of stress state within the part is extremely valuable and would result in optimization of the process parameters in achieving a desired RS and control of the build process. This paper proposes a physics-based analytical model to rapidly and accurately predict the RS within the additively manufactured part. In this model, a transient moving point heat source (HS) is utilized to determine the temperature field. Due to the high temperature gradient within the proximity of the melt pool area, material experience high thermal stress. Thermal stress is calculated by combining three sources of stresses known as stresses due to the body forces, normal tension, and hydrostatic stress in a homogeneous semi-infinite medium. The thermal stress determines the RS state within the part. Consequently, by taking the thermal stress history as an input, both the in-plane and out of plane RS distributions are found from incremental plasticity and kinematic hardening behavior of the metal by considering volume conservation in plastic deformation in coupling with the equilibrium and compatibility conditions. In this modeling, material properties are temperature-sensitive since the steep temperature gradient varies the properties significantly. Moreover, the energy needed for the solid-state phase transition is reflected by modifying the specific heat employing the latent heat of fusion. Furthermore, the multi-layer and multi-scan aspects of metal AM are considered by including the temperature history from previous layers and scans. Results from the analytical RS model presented excellent agreement with XRD measurements employed to determine the RS in the Ti-6Al-4V specimens.

The main focus of the in vitro toxicity assessment methods is on the viability of the cells, which is usually based on metabolism changes. Yet, when exposed to toxic substances, the cell triggers multiple signals in response. With this in mind, we have developed a promising cell-based toxicity method that observes various cell responses when exposed to toxic substances (either death, division or remaining viable). Based on the collective cell response, we observed and predicted the dynamics of the cell population to determine the toxicity of the toxicant. The method was tested with two different conformations: In the first conformation, we exposed a monoculture model of blood macrophages to UV light, hydrogen peroxide, nutrient deprivation, tetrabromobisphenol A, fatty acids and 5-fluorouracil. In the second, we exposed a coculture liver model consisting of hepatocytes, hepatic stellate cells, Kupffer cells and liver sinusoidal endothelial cells to rifampicin, ibuprofen and 5-fluorouracil. The method showed good accuracy compared to established toxicity assessment methods. In addition, this approach provided more representative information on the toxic effects of the compounds as it considers the different cellular responses induced by toxic agents.

The purpose of this study is to analyze the self-regulated learning and the ability to write scientific papers of students after learning with the Project-Based Digital Science Module (DSM). This research is a mixed methods by analyzing quantitatively and qualitatively. The research instrument used to obtain data is using a product assessment sheet and a self-regulated learning questionnaire. Data analysis uses N-Gain to determine the increase in self-regulated learning scores and student scientific writing skills scores, and uses linear regression analysis to determine the effect of self-regulated learning on student scientific writing skills. The results obtained showed N-Gain score of learning independent is 0,65 and scientific writing ability is 0,94, then significant’s score from linear regression by using SPSS is 0,22 < 0,05. This result showed an increase in self-regulated learning and the ability to write scientific papers of students on each indicator after learning using the Project-Based Digital Science Module (DSM). In addition, based on the results of data analysis, it can be seen that there is an influence of self-regulated learning on the ability to write scientific papers of students after learning using the Project-Based Digital Science Module.

Colours act as stimuli capable of inducing physiological and psychological responses, impacting on human life by influencing behaviour, cognition and emotion. Designers frequently draw upon colour association cues in designing products, packaging and marketing materials to exploit the reported human reactions to them. To date, clinicians and foot orthoses manufacturers appear to have given little thought to how the colour of foot orthoses may have impact within the broader context of a biopsychosocial model of healthcare. Here we examine research regarding colour perception and association and provide rationale for how the use of colour in foot orthoses therapy might be better exploited to improve patient outcomes and to form a focus for future research.

We demonstrate a proof-of-principle of simple all-solid-state post-compression setup for low energy, high repetition rate laser pulses, where spectral broadening was performed using a combination of highly nonlinear bulk materials in a simple single pass geometry. 75 fs, 210 nJ pulses from an amplified 76 MHz, 15.7 W Yb:KGW oscillator after sequential spectral broadening in ZnS and YAG samples of 2 mm and 15 mm thickness, respectively, were compressed to 37 fs by means of Gires–Tournois interferometric mirrors. The post-compressed pulses with an average power of 11.47 W demonstrated reasonable spatial-spectral homogeneity of the beam with the spectral overlap parameter V>83% and good beam quality with Mx2=1.28 and My2=1.14.

In the present work, a predictive modelling and optimization with the adaptive network based fuzzy inference system(ANFIS) modelling of mechanical properties of laser-coated NB/SiC/Ni welds was studied based on Taguchi design by laser cladding. An ANFIS model based on a Sugeno type fuzzy inference system was developed for predicting the hardness properties of SiC/BN/Ni welds by laser cladding with experimental data required for network training and prediction. Based on analysis of variance, three important factors were taken as inputs for the fuzzy logic inferences, while the hardness properties was taken as the output of the ANFIS. The microstructure of welds were analysed using scanning electron microscopy with an energy dispersive X-Ray spectrometer. Highly developed leaf-like dendrites and eutectic crystals were found in some areas of the melting zone for the BN/SiC/Ni weld, which was significantly hardened. The ANFIS model based on Taguchi's design provides a better pattern of response because the predicted and experimental values were highly similar. As a result, a satisfactory result was achieved between the predicted and experimental values of hardness in laser-coated NB/SiC/Ni welds, whereby the success and validity of the method was verified.

As the additive manufacturing industry grows, it is compounding the global plastic waste problem. Distributed recycling and additive manufacturing (DRAM) offers an economic solution to this challenge, but it has been relegated to either small-volume 3D printers (limiting waste recycling throughput) or expensive industrial machines (limiting accessibility and lateral scaling). To overcome these challenges, this paper provides proof-of-concept for a novel open-source hybrid 3D printer that combines a low-cost hanging printer design with a compression screw-based end-effector that allows direct extrusion of recycled plastic waste in large expandable printing volumes. Mechanical testing of the resultant prints from 100% waste plastic, however, showed that combining challenges of non-uniform feedstocks and a heavy printhead for a hangprinter reduced the strength of the parts compared to fused filament fabrication. The preliminary results are technologically promising, however, and provide opportunities to improve on the open source design to help process the volumes of waste plastic needed for DRAM to address the negative environmental impacts of global plastic use.

Undergraduate learning is a multifaceted concept that many researchers have investigated to promote student engagement, academic performance, etc. Exploring factors promoting learning among undergraduates in FYW programs, which are required for undergraduates might potentially contribute to sustainable, cross-disciplinary undergraduate education. This study used the 10-year longitudinal grade and survey data at San José State University (SJSU) and the data was collected from Academic Years (AYs) 2015 to 2020, and five student surveys constituted the sample size of 18,101 students. In 2016, SJSU changed the remedial writing course to college writing courses. Since then, students need to complete an online module course before placing themselves into a one-semester or two-semester writing course. The previous study showed that students with higher writing comfort and confidence tend to place themselves into a semester-long class. Regression analysis was applied to examine the relationships among factors promoting learning among those students. University admitted students from various diversity and backgrounds, the results of this study suggested that what students chose and persisted in were more important in advancing their academic success rather than prior learning experience or psychological factors before the class.

Considered one of the finest first-generation Nigerian writers, John Pepper Clark-Bekederemo, who passed away on 13th October, 2020, had been categorised as a Eurocentric writer. This work assesses the authenticity or otherwise of this critics’ perception of Clark by critiquing his America, their America. By analysing this autobiography vis-à-vis the notion of self and other which is a theoretical concern in contemporary travel writing, it was established, among other things, that every culture has its dark sides which it must not feel too proud to change as time and situation demand; that Clark vehemently rejects the Americans’ claim of sophistication and superiority of their culture over African culture. The paper concludes that contemporary travel writing should be a rightful site for negotiating cultural, political and diplomatic compromises between the Self and the Other since the gulf may be difficult to close altogether.

The paper presents the results of high precision control survey carried out in the underground mining of Oyu Tolgoi project using terrestrial laser scanning technology. The purpose of the measurements is to ensure the heading, total length and volume of the penetration and excavation works are being implementing in accordance with the planned and designed dimensions. We established a network of 18 reference points in the tunnel of the selected underground level which were repeatedly measured 4 times by two round readings of the Trimble S7 tacheometry and processed by using the Trimble Business Center software. All points except the one was within the permissible error. Based on these points the excavation length and volumes were determined using the Trimble SX12 laser scanner. The difference between the planned work quantity provided by the Oyu Tolgoi project and the actual values measured by the laser scanning was calculated using the comparative method. The TLS partial control measurements in the excavations made through the ore bodies revealed the length of 20285.72 m and volume of 441128.80 m3 for underground 7 mine levels while their project values were 16158.26 m length and 422837.50 m3 volume, respectively.

The new regulation was introduced to the franchise market of South Korea in that an applicant who wants to be a franchiser must set up direct retail stores and run them for at least one year before recruiting franchisees. Considering the purpose of the regulation, it is inferred that once franchisers run their own stores, their franchisees would be better off than otherwise. This paper addresses one reason that the Korea Fair Trade Commission has no choice but to introduce the regulation. Along the line, this paper investigates whether franchisees would have the more likelihood to make profit in the case of that franchisers operate their own stores. The result demonstrates that this case could be true since the operation of franchiser owned stores could be helpful in reducing cost of franchisees.

Energy and information are fundamental concepts that play crucial roles in the foundations of science, each contributing to different aspects of our understanding of the natural world. Here we encounter that Fisher' measure is able to link them. We also investigate some interesting relations between Fisher's information, Poisson's distribution, and thermal quantifiers in a grand canonical ensemble. These connections permit one to visualize interesting novel artifacts in statistical mechanics. We clearly see them emerge in discussing the ideal gas. For example, we encounter that the Poisson distribution is intrinsically involved in the physics of the ideal gas, and we are able to give a Fisher-estimation of the difference in informational content between the grand canonical and canonical ensembles.

This paper discusses corporate taxes and Foreign Direct Investment (FDI) in Nigeria. It is a review of literature that attempts to explore and give a reality on the response of FDI to corporate taxes. This paper shows in its introductory phase a prior discussion of the terms corporate tax and FDI and also elements of both terms and classifications. It follows with issues such as the effects of corporate taxes on FDI. This paper discusses the rhetoric whether reduced corporate taxes and other tax incentives has an effect on the inflow of FDI in Nigeria. To answer this question, the paper utilised information gathered from secondary sources including books, newspapers publications, working papers and research findings from studies. This paper shows that from surveyed empirical studies corporate taxes may have an important role in attracting FDI and have a rising effect on the development of the country, and as such recommends that tax incentives should be employed as a means to attracting FDI, a cost benefit analysis should be employed on the types of corporate taxes to determine the benefit from the perceived FDI inflow, in addition a review of the current tax policies should be carried out as they seem not to respond to the current economic situation.

Media is obtaining a leading role in contemporary strategic communication, the development especially visible in the context of social-political and geopolitical conflicts. This study introduces an interdisciplinary theory of Social Laser and applies it in the analysis of social mobilization around the current militarized situation in Eastern Europe. We analyze quantitatively the content of three Swedish newspapers and qualitatively the related Facebook discussions. As demonstrated, social lasing has been employed as an instrument in information warfare. An “information tsunami” was generated by the Swedish national mass media at the outbreak of military events in March-May 2022. It shaped social dynamics on the related social media platform. The intensity of dissident actions increased when the information pressure subsided.

The impact induced by cavitation bubble collapse can be utilized for mechanical surface treatment to improve fatigue properties of metals including additive manufactured metallic materials. A peening method using cavitation impact induced by a pulsed laser is called “laser cavitation peening (LCP)”. Normally, a Q-switched Nd:YAG laser, whose pulse width is a few nanoseconds, is used for LCP, which improves the fatigue strength. The problem with LCP is that the processing time is too slow. If a laser pulse whose pulse width is a few hundred microseconds can be utilized for LCP, the repetition frequency can be increased drastically using other types of laser systems such as a fiber laser. In the present paper, in order to reveal the possibility of LCP using a pulsed laser width of a few hundred microseconds, the use of LCP with a normal-oscillation Nd:YAG laser (pulse width ≈ 200 us) was investigated. It is demonstrated that LCP with the normal-oscillation Nd:YAG laser produced curvature in an aluminum alloy plate.

The present work proposes a novel manufacturing technique based on the combination of Laser Metal Deposition, Laser Beam Machining and Laser Polishing processes for the complete manufacturing of complex parts. Therefore, the complete process is based on the application of a laser heat source both for the building of the preform shape of the part by additive manufacturing and for the finishing operations. Their combination enables to manufacture near-net-shape parts and afterwards, remove the excess material via laser machining, which has resulted to be capable of eliminating the waviness resulting from the additive process. Besides, surface quality is improved via laser polishing to reduce the roughness of the final part. Therefore, conventional machining operations are eliminated, what results in a much cleaner process. In order to validate the capability of this new approach, the dimensional accuracy and surface quality of the resulting parts are evaluated. The process has been validated on an Inconel 718 test part, where a previously additively built up part has been finished by means of laser machining and laser polishing.

Laser-plasma interactions of ultra-short laser pulses with solid targets can generate highly intense pulses of protons and ions with energies of several MeV. The spectra of these particles are spread over a wide range following a Maxwellian distribution. We report on the design and testing of a magnetic chicane for the selection of protons within a limited energy window. It consists in two successive, anti-parallel dipole fields generated by cost-effective, permanent C-magnets with customized configuration and longitudinal positions. The chicane has been implemented into the target vessel of a petawatt laser facility under constraints on the direction of the incoming laser beam and guidance of the outgoing particles through a vacuum port. The separation of protons and carbon ions within distinct energy intervals has been demonstrated and compared to a ray tracing code.

The use of Light Amplification by Stimulated Emission of Radiation (i.e., LASERs or lasers) by the U.S. Department of Defense is not new and includes laser weapons guidance, laser-aided measurements, even lasers as weapons (e.g., Airborne Laser). Lasers in support of telecommunications is also not new. The use of laser light in fiber optics shattered thoughts on communications bandwidth and throughput. Even the use of lasers in space is no longer new. Lasers are being used for satellite-to-satellite crosslinking. Laser communication can transmit orders-of-magnitude more data using orders-of-magnitude less power and can do so with minimal risk of exposure to the sending and receiving terminals. What is new is using lasers as the uplink and downlink between the terrestrial segment and the space segment of satellite systems. More so, the use of lasers to transmit and receive data between moving terrestrial segments (e.g., ships at sea, airplanes in flight) and geosynchronous satellites is burgeoning. This manuscript examines the technological maturation of employing lasers as the signal carrier for satellite communications linking terrestrial and space systems. The purpose of the manuscript is to develop key performance parameters (KPPs) to inform U.S. Department of Defense initial capabilities documents (ICDs) for near-future satellite acquisition and development. By appreciating the history and technological challenges of employing lasers rather than traditional radio frequency sources for satellite uplink and downlink signal carrier, this manuscript recommends ways for the U.S. Department of Defense to employ lasers to transmit and receive high bandwidth, large-throughput data from moving platforms that need to retain low probabilities of detection, intercept, and exploitation (e.g., carrier battle group transiting to a hostile area of operations, unmanned aerial vehicle collecting over adversary areas). The manuscript also intends to identify commercial sector early-adopter fields and those fields likely to adapt to laser employment for transmission and receipt.

Directional dithering of a laser beam potentially limits the detection accuracy of a laser triangulation displacement probe. A theoretical analysis indicates that the measurement accuracy will linearly decrease as the laser dithering angle increases. To suppress laser dithering, a laser triangulation displacement probe with laser beam pointing control, which consists of a collimated red laser, a laser beam pointing control setup, a receiver lens, and a charge-coupled device, is proposed in this paper. The laser beam pointing control setup is inserted into the source laser beam and the measured object and can separate the source laser beam into two symmetrical laser beams. Hence, at the angle at which the source laser beam dithers, the positional averages of the two laser spots are equal and opposite. Moreover, a laser dithering compensation algorithm is used to maintain a stable average of the positions of the two spots on the imaging side. Experimental results indicate that with laser beam pointing control, the standard variance of the fitting error decreases from 0.3531 to 0.0100, the repeatability accuracy can be decreased from ±7mm to ±5 μm, and the nonlinear error can be reduced from ±6 %FS to ±0.16 %FS.

The reagents and raw materials used, as well as the products obtained (bio-oil, reaction condensates, polyols and sugar phases) were characterized by elemental analysis, infrared spectroscopy, thermogravimetry and high performance liquid chromatography with mass spectrometry. The heating value of the bio-oils is higher than that of the original biomass (higher heating value of Eucalyptus sawdust bio-oil 29 MJ/kg versus 19.5 MJ/kg of the original Eucalyptus sawdust). The analyses of the bio-oils allowed to identify the presence of high added-value compounds, such as levulinic acid and furfural. Finally, a study of the accelerated aging of the liquefied biomass showed that the biofuel density increases with the storage time due to the occurrence of repolymerization reactions.

To assist Java programming learning of novice students, we have developed the web-based Java programming learning assistant system (JPLAS). JPLAS provides several types of exercise problems to cultivate code reading/writing skills at various levels. In JPLAS, the code writing problem (CWP) asks a student to write a source code that will pass the test code given in the assignment where the correctness is verified by running them on JUnit. In this paper, to reduce the teacher load at marking process, we present the answer code validation program that verifies all the source codes from a lot of students for each assignment at a time and reports the number of passing tests for each source code in the CSV file. Besides, to test a source code with various input data, we implement the test data generation algorithm that identifies the data type, generates a new data, and replaces it for each test data in the test code. Furthermore, to verify the correctness of the implemented procedure in the source code, we introduce the intermediate state testing in the test code. For evaluations, we applied the proposal to source codes and test codes in a Java programming course in Okayama university, Japan, and confirmed the validity and effectiveness.

The purpose of this study is to show an automated laser vision correction (LVC) with the transep-ithelial refractive keratectomy (TransPRK) surgery technique. Since more surgical steps have been automated over the years, we have standardized the TransPRK technique. We have been using it since 2010. This paper aims to illustrate the processes that are readily applicable to automation. To meet the patient's expectations and ensure that the patient has uncorrected visual acuity at least equal to the preoperative corrected vision with glasses, patient selection is crucial in refractive surgical procedures. One major benefit of automating the surgery is that it can be performed in a similar way by each surgeon or laser correction centre, so once the standard and results are good, these can be per-formed by different surgeons.

3D meso-scale structures that can reach up to centimeters in overall size but retain micro- or nano-features, proved to be promising in various science fields ranging from micro-mechanical metamaterials to photonics and bio-medical scaffolds. In this work we present synchronization of the linear and galvano scanners for efficient femtosecond 3D optical printing of objects at the meso-scale (from sub-μm to sub-cm spanning five orders of magnitude). In such configuration the linear stages provide stitch-free structuring at nearly limitless (up to tens-of-cm) working area, while galvo-scanners allow to achieve translation velocities in the range of mm/s-cm/s without sacrificing nano-scale positioning accuracy and preserving undistorted shape of the final print. The principle behind this approach is demonstrated, proving its inherent advantages in comparison to separate use of only linear stages or scanners. The printing rate is calculated in terms voxels/s, showcasing the capability to maintain an optimal feature size while increasing throughput. Full capabilities of this approach are demonstrated by fabricating structures that reach millimeters in size but still retain μm-scale features: scaffolds for cell growth, microlenses and photonic crystals. All this is combined into a benchmark structure: a meso-butterfly. Provided results show that synchronization of two scan modes is crucial for the end goal of industrial-scale implementation of this technology and makes the laser printing well aligned with similar approaches in nanofabrication by electron and ion beams.

Microbial immune escape represents the primary cause of induced pathogenesis in humans, and it represents a pivotal method used by viral agents to increase their load and suppress key mechanisms of the innate and adaptive immune system. This phenomenon represents the primary factor that led to the onset of the 1918-1920 A(H1N1) Influenza and 2020-2022 COVID-19 pandemics, and it possibly played a major role in the onset of the AIDS pandemic as well. Moreover, repeated incidents of immune evasion could be associated with higher rates of cellular aging (Jackson et al., 2017), most likely due to the consequent increased demands of energy consumption. Highly developed viral immune evasion ultimately indicates the high inner intelligence of human immunity due to reflective and imitative characteristics of reactions that are produced against initial actions. Ribonucleic acid-based viral genomes contain open reading frames, which consist of genes producing sixteen non-structural proteins. Such proteins play a considerable role in desensitizing first-line immunity during cellular infection, and non-structural proteins 1, 10 and 16 have the strongest effects against a healthy expression rate of Type I and Type III Interferon-encoding genes. Type I Interferons consist of IFN-alpha, -beta, -delta, -epsilon, -omega, -tau and -zeta, whilst Type III Interferons consist of IFN-lambda1, -lambda2 and -lambda3, and they act as stimulators of intracellular signalling cascades that in turn lead to the activation and expression of interferon-stimulated genes (Brown et al., 2022). The earlier the interferon-stimulated genes are activated, the lower the extent of pro-inflammatory mediation and overall, the more effective the antiviral immune response will be, given the exponential nature of the viral load increase. Non-structural protein 16 methylates the 5’ cap of the virus, making the pathogen-associated molecular patterns less recognisable by pattern-recognition receptors, and it requires activation by bonding with non-structural protein 10. It is preserved in the S-Adenosyl-L-Methionine pocket of the SARS-CoV-2 genome. Non-structural protein 1 (NS1) directly cleaves the host cell mRNA producing Type I and possibly Type III Interferons, thereby preventing a translation process of the immune proteins. NS1 has recently been found to often be packaged into exosomes once secreted by the viral genome in the cytosol, meaning that exocytosis and paracrine signalling to neighbouring cells before their actual infection is possible. As a result, NS1 is highly capable of silencing the first-line immune responses of uninfected neighbouring cells as well, thereby highlighting the need to adjust the focus of therapeutics and vaccinology toward first-line immunity and further indicating its foundational importance in the support for the development of precise and balanced defenses against microbial agents of concern (EL SAFADI et al., 2022).

Within the spectra of lanthanide atoms quite often overlapping spectral lines (blends) are observed. On the example of complicated blend situations within Pr I and La I it is shown that in such cases a combination of optogalvanic and laser-induced fluorescence detection is necessary to find all transitions contributing to the observed spectral signature.

This article reports new measurements of laser-induced plasma hypersonic expansion measurements of diatomic molecular cyanide (CN). Focused, high-peak power 1064-nm Q-switched radiation of the order of 1 TW/cm² generates optical breakdown plasma in a cell containing a 1:1 molar gas mixture of N₂ and CO₂ at a fixed pressure of 1.1 × 10⁵ Pascal and in a 100 ml/min flow of the mixture. Line-of-sight (LOS) analysis of recorded molecular spectra indicate the outgoing shockwave at expansion speeds well in excess of Mach number 5. Spectra of atomic carbon confirm an increased electron density near the shock wave, and equally, molecular CN spectra reveal higher excitation temperature near the shockwave. The results are consistent with corresponding high-speed shadow graphs obtained by visualization with an effective shutter speed of five n anosecond. In addition, LOS analysis and application of integral inversion techniques allow inferences about the spatio-temporal distribution of the plasma.

The wealth of data obtained during the past 20 years using Laser-Induced Breakdown Spectroscopy (LIBS) indicates that the technique is very promising to detect small chemical contents of alloying elements. The potential of LIBS was looked more seriously during the past two decades or so as more data were obtained on Aluminum and steel to study the phenomena in the condition of local thermodynamic equilibrium and time-delay between a Q-switch laser and an intensified CCD camera. Since the past decade, some data on compounds were also shown to be useful in determining small concentrations of harmful elements. This manuscript is intended to show that the technique of LIBS performance is very promising in fields such as micro-machining, in alloying element analysis, surface cleaning and environmental applications even with lightweight spectrometers having a relatively low resolution, which can potentially be air-borne.

Self-phase modulation (SPM) broadening of laser spectra was studied in a transmission mode in natural and synthetic diamonds at variable laser wavelengths (515 and 1030 nm), pulse energies and widths (0.3 - 12 ps, positively chirped pulses), providing their filamentary propagation. Besides the monotonous SPM broadening of the laser spectra versus pulse energy, more pronounced for the (sub)picosecond pulsewiths and more doped natural diamond, periodical low-frequency modulation was observed in the spectra at the shorter laser pulsewidths, indicating dynamic Bragg filtering of the supercontinuum due to ultrafast plasma and nanoplasmonic effects. Damping of broadening and ultramodulation for the longer picosecond pulsewidths was related to thermalized electron-hole plasma regime established for the laser pulsewidths longer, than 2 ps. Unexpectedly, at higher pulse energies and corresponding longer microfilaments, the number of spectral modulation features increases, indicating dynamic variation of the periods in the longitudinal plasma Bragg gratings along the filaments due to prompt secondary laser-plasmon interactions.

The purpose of this study is to identify the steps involved in fabricating silica/chitosan composite membranes and their suitability in fuel cell application. It also intends to identify the physical characteristics of chitosan composite membranes, including their degree of water absorption, proton conductivity, methanol permeability, and functional groups. In this investigation, composite membranes were fabricated using the solution casting method with chitosan content of 5 g and silica variations dosage of 2% and 4% while stirring at a constant speed for 2h. According to the findings, the analysis of composite membranes produced chitosan membranes that were successfully modified with silica. The optimum membrane was found to be 4% s-SiO2 from the Sol-gel method with composite membrane's optimal condition of 0.234 cm/s proton conductivity, water uptake of 56.21%, and reduced methanol permeability of 0.99 × 10 -7 cm2/s in the first 30 minutes and 3.31 × 10-7 in the last 150 minutes. Maintaining lower water uptake capacity at higher silica content is still a challenge that needs to be addressed. However, the fabricated membranes showed exceptional results in terms of proton conductivity and methanol permeability.

In this study, we investigate spectral structure of conformable Sturm-Liouville problems and with this end, we obtain representation of solutions under different initial conditions and asymptotic formulas for eigenfunctions, eigenvalues, norming constants and normalized eigenfunctions. Consequently, we prove the existence of infinitely many eigenvalues. Also, we compare the solutions with graphics with different orders, different eigenvalues, different potentials and so, we observe the behaviors of eigenfunctions. We give an application to the α-orthogonality of eigenfunctions and reality of eigenvalues for conformable Sturm-Liouville problems defined by [15] in the last section.

Polymer adhesives have emerged as a promising dielectric passivation layer in hybrid bonding for 3D integration while they raise misalignment problems during curing. In this work, the synergistic effect of oxygen plasma surface activation and wetting is utilized to achieve bonding between completed cured polyimides. The optimized process achieves a void-less bonding with a maximum shear strength of 35.3 MPa at a low temperature of 250 °C in merely 2 min, significantly shortening the bonding period and decreasing thermal stress. It is found that the plasma activation generated hydrophilic groups on the polyimide surface, and the wetting process further introduced more -OH groups and water molecular on the activated polyimide surface. The synergistic process of plasma activation and wetting facilitate bridging polyimide interfaces to achieve bonding, providing an alternative path for adhesive bonding in 3D integration.

The goal of this paper is to propose a dual version of the direct cosine simplex algorithm (DDCA) for general linear problems. Unlike the two-phase and the big-M methods, our technique does not involve artificial variables. Our technique solves the dual Klee-Minty problem in two iterations and solves the dual Clausen’s problem in four iterations. The utility of the proposed method is evident from the extensive computational results on test problems adapted from NETLIB. Preliminary results indicate that this dual direct cosine simplex algorithm (DDCA) reduces the number of iterations of two-phase method.

Nonlinear properties of zinc germanium diphosphide (ZGP) crystals enable their ap-plications in powerful mid-IR optical parametric oscillators and second-harmonic generators. This paper summarizes mechanisms of the laser induced damage (LID) in high-purity ZGP crystals under periodically pulsed nanosecond irradiation by a Ho3+:YAG laser at 2.1 μm. The ZGP samples were manufactured by “LOC” Ent., Tomsk, Russia, or Harbin Institute of Technology, China. The impact of processing techniques and the post-growing methods for polishing and anti-reflection coating on the LID threshold are discussed. The importance of the defect structure of the crystal lattice and the parameters of transparent coatings for increasing the LID threshold is discussed. The impact of the test laser parameters on the LID threshold is analyzed. The transient area near the LID threshold obtained using digital holography is ana-lyzed. Influence of the pre-damage processes on the optical parametric oscillations is reported. Prospects for improving ZGP crystals to further increase the LID threshold are discussed.

During submerged laser peening using a pulsed laser, a bubble that behaves like cavitation is generated after laser ablation (LA). The bubble is referred to as laser cavitation (LC). The amplitude of the shock-wave in LA water is larger than that of LC; however, the impact passing through the target metal during LC is larger than that of LA. Thus, submerged laser peening is referred to as “laser cavitation peening”, as the peening method using the cavitation impact is known as “cavitation peening”. The impact induced by a hemispherical bubble is more aggressive than that of a spherical bubble with a microjet. Laser cavitation peening can improve the fatigue strength of metallic materials by producing work-hardening and the introduction of compressive residual stress. Three-dimensional additive manufactured metals (3D metals) such as titanium alloy are attractive materials for aviation components and medical implants; however, the fatigue strength of as-built components is nearly half that of bulk metals, and this is an obstacle for the applications of 3D metals. In the present study, published research papers were reviewed to identify the key factors of laser cavitation peening, with additional visualization of LC and data. Then, improvements in the fatigue strength of metallic materials, including 3D metals produced by laser cavitation peening, were summarized.

Three-dimensional porous nanostructures made of noble metals represent novel class of nanomaterials promising for nonlinear nanooptics and sensors. Such nanostructures are typically fabricated using either reproducible yet time-consuming and costly multi-step lithography protocols or less reproducible chemical synthesis that involve liquid processing with toxic compounds. Here, we combined scalable nanosecond-laser ablation with advanced engineering of the chemical composition of thin substrate-supported Au films to produce nanobumps containing multiple nanopores inside. Most of the nanopores hidden beneath the nanobump surface can be further uncapped using gentle etching of the nanobumps by an Ar-ion beam to form functional 3D plasmonic nanosponges. The nanopores 10-150~nm in diameter were found to appear via laser-induced explosive evaporation/boiling and coalescence of the randomly arranged nucleation sites formed by nitrogen-rich areas of the Au films. Density of the nanopores can be controlled by the amount of the nitrogen in the Au films regulated in the process of their magnetron sputtering assisted with nitrogen-containing discharge gas.

In most studies reported in literature, a flat, constant coefficient is used to convert the amount of optical power required at the input of an optical link into the effective power consumption. This constant coefficient approach is very simple to apply but not accurate, since laser efficiencies are dependent on the optical output power in addition to the operating temperature. In this paper the relationship between laser wall plug efficiency and optical power output is investigated and the effect of this variance on optical links and on-chip laser source electric power consumption is presented

The ability to control the temperature distribution T(t,r) and the rate of temperature change Rt,r inside glasses is important for their microstructuring. The lattice temperature is considered at time t, exceeding the electron-phonon thermalization time, and at a distance r from the center of the model spherical heating zone. In order to describe thermal excitations, the heat capacity of glasses must be considered as a function of time due to its long-term relaxation. A method for analytical calculation of T(t,r) and R(t,r) for glasses with dynamic heat capacity cdyn(t) is proposed. It is shown that during laser microstructuring the local cooling rate -R(t,r) significantly depends on the time dispersion of cdyn(t). It has been established that at the periphery of the model heating zone of the laser beam focus, the local cooling rate can reach more than 1011 K/s. Strong cooling rate gradients were found at the periphery of the heating zone, affecting the microstructure of the material. This effect is significantly enhanced by the time dispersion of cdyn(t). The effect associated with this time dispersion is significant even well above the glass transition temperature Tg, since even short relaxation times of the dynamic heat capacity cdyn(t) are significant.

Materials known as Nd:YAG are crystalline materials of the cubic system made from neodymium-doped yttrium aluminum garnet, which among others, have excellent optical properties. Nd:YAG four-level laser devices are highly used in both the health and industrial sectors. In this study, a simple and inexpensive alternative to manufacturing Nd:YAG materials through solid state reactions following powder processing routes was proposed. For this, an intense mixture of the precursor materials (Al2O3 and Y2O3) was carried out, followed by the addition of neodymium atoms to improve the optical properties of the resulting material. High energy mechanical mixing of the precursor powders resulted in submicron particles, with good size distributions of the powders. The advance of YAG formation was monitored by intermediate phase formation during heat treatment through interrupted tests at different temperatures and analysis by X-ray diffraction. From this analysis, it was found that reaction for the formation of the desired YAG is completed at 1500°C. Fourier-transform infrared spectroscopy analyses determined the presence of functional groups corresponding to the YAG. Finally, the study by optical emission spectroscopy showed wavelengths in agreement with the electronic structure of the elements of the synthesized Nd:YAG.

With the development of industrialization, traditional manufacturing technologies are no longer able to meet the production needs of modern society. Additive manufacturing has successfully solved the problems existing in traditional manufacturing technology. Selective laser melting (SLM) is a powder bed melting technology that produces metal parts by selectively melting metal powders on a platform using a laser beam. It is widely used in additive manufacturing. This article introduces the characteristics and current development status of SLM technology, summarizes the main application fields and common defects of SLM, and finally explores and prospects the future development trend of SLM.

Tengchongite is a uranyl molybdate uranium mineral and it was found and named by Chen 1985.No more scholars studied on tengchongite after Chen’s work, The identification of this mineral has only been confirmed by single crystal X-ray diffraction. In the paper, micro laser Raman spectroscopy and infrared spectroscopy are used to identify the spectroscopy properties of tengchongite. The studies fill in the gaps of more than 30 years in terms of the molecular spectroscopy research of tengchongite. The mineral has an ideal model of Ca(UO₂)₆(MoO₄)₂O₅•12H₂O its bands attributed to the vibrating units are clearly identified in the Raman spectrum. Symmetric stretching modes at 812 cm^-1 and 839 cm^-1 are assigned to ν1 (UO₂)²⁺ ,The ν3 antisymmetric stretching modes of (UO₂)²⁺ are observed at 896 cm^-1, Symmetric stretching modes at 419^-1 and 440 cm^-1 are assigned to ν2 (UO₂)²⁺ .Symmetric stretching modes at 919cm-1 are assigned to ν1(MoO₄)^2-,The ν3 antisymmetric stretching modes of (MoO₄)^2- are observed at 752 cm^-1, the in-plane ν2(MoO₄)^2-and the out-of-plane ν4(MoO₄)^2- bending modes are at 169 cm^-1 and 254 cm^-1. IR spectrum of tengchongite shows the major uranyl band at 858 cm^-1 and 693 cm^-1, Mo-O bonds are observed at about 985 cm^-1 and 780 cm^-1, and H₂O groups are present with a wide range peaks from 3100 cm^-1 to 3500 cm^-1 and 1647 cm^-1, and the band at 1432.4 cm^-1 is probably due to the stretching vibration hydroxyl (OH^-1), therefore, tengchongite contains may include hydroxyl and its chemical formula needs to be modified .

Laser scanning is an effective tool for acquiring geometric attributes of trees and vegetation, which lays a solid foundation for 3-dimensional tree modelling. Existing studies on tree modelling from laser scanning data are vast. Nevertheless, some works don’t ensure sufficient modelling accuracy, while some other works are mainly rule-based and therefore highly depend on user inputs. In this paper, we propose a novel method to accurately and automatically reconstruct tree branches from laser scans. We first extract an initial tree skeleton from the input tree point cloud, then simplify the skeleton through iteratively removing redundant components. A global-optimization approach is performed to fit a sequence of cylinders to approximate the geometry of the tree branches. Experiments on various types of trees from different data sources demonstrate the effectiveness and robustness of our method. The resulted tree models can be further applied in the precise estimation of tree attributes, urban landscape visualization, etc.

Inorganic and organic – inorganic (hybrid) perovskite semiconductor materials have attracted the worldwide scientific attention and research effort as the new wonder material in optoelectronics. Their excellent physical and electronic properties have been exploited to boost the solar cells efficiency beyond 23% and captivate their potential as competitors to the dominant silicon solar cells technology. However, the fundamental principles in Physics dictate that an excellent material for photovoltaic applications must be also an excellent light emitter. This has been realized for the case of perovskite based light emitting diodes (LEDs) but much less for the case of the respective laser devices. Here, the strides have been made since 2014 are presented for the first time. The solution processability, low temperature crystallization, formation of nearly defect free, nanostructures, the long range ambipolar transport, the direct energy band gap, the high spectral emission tunability over the entire visible spectrum and the almost 100% external luminescence efficiency show perovskite semiconductors’ potential to transform the nanophotonics sector. The operational principles, the various adopted material and laser configurations along the future challenges are reviewed and presented in this paper.

We present a numerical illumination model to calculate direct as well as diffuse or Hapke scattered radiation scenarios on arbitrary planetary surfaces. This includes small body surfaces such as main belt asteroids as well as e.g. the lunar surface. The model is based on the raytracing method. This method is not restricted to spherical or ellipsiodal shapes but digital terrain data of arbitrary spatial resolution can be fed into the model. Solar radiation is the source of direct radiation, wavelength-dependent effects (e.g. albedo) can be accounted for. Mutual illumination of individual bodies in implemented (e.g. in binary or multiple systems) as well as self-illumination (e.g. crater floors by crater walls) by diffuse or Hapke radiation. The model is validated by statistical methods. A χ2 test is undertaken to compare simnulated images with DAWN images acquired during the survey phase at small body 4 Vesta.

Data obtained by Direct Numerical Simulations (DNS) of pressure-driven turbulent channel flow are studied in the range 180 ≤ Reτ≤ 10,000. Reynolds number effects on the Mean Velocity Profile (MVP) and second order statistics are analyzed with a view of finding logarithmic behavior in the overlap region or even further from the wall, well in the boundary layer’s outer region. Values of Kármán constant for the MVPs and the Townsend-Perry constants for the streamwise and spanwise fluctuation variances are determined for the Reynolds numbers considered. A data-driven model of the MVP, proposed and validated for zero pressure gradient flow over a flat plate, is employed for pressure-driven channel flow by appropriately adjusting Coles’ strength of the wake function parameter, Π. There is excellent agreement between the analytic model predictions of MVP and the DNS-computed MVP as well as of the Reynolds shear stress profile. The skin friction coefficient Cf is calculated analytically. The agreement between the analytical model predictions and the DNS-based computed discrete values of Cf is excellent.

The sandwich format immunoassay is generally more sensitive and specific than more common assay formats, including direct, indirect, or competitive. A sandwich assay, however, requires two receptors to bind non-competitively to the target analyte. Typically, pairs of antibodies (Abs) or antibody fragments (Fabs) capable of forming a sandwiching with the target are identified through a slow, guess-and-check method with panels of candidate binding partners. Additionally, sandwich assays reliant on commercial antibodies can suffer from changes to reagent quality outside the researchers’ control. This report presents a reimagined and simplified phage display selection protocol that directly identifies sandwich binding peptides and Fabs. The approach yielded two sandwich pairs, one peptide-peptide and one Fab-peptide sandwich for the cancer and Parkinson’s disease biomarker DJ-1. Requiring just a few weeks to identify, the sandwich pairs delivered apparent affinity comparable to other commercial peptide and antibody sandwiches. The results reported here could expand the availability of sandwich binding partners for a wide range of clinical biomarker assays.

The thermal properties of novel nanomaterials play a significant role in determining the performance of the material in technological applications. Herein, direct measurement of the temperature diffusivity of cellulose nanocomposite films was carried out by the micro-contact method. Polymer films containing up to 2%wt. of nanocellulose were synthesised by a simple chemical process. Films of a high optical transmittance T ≈ 80 % (for a 200- μ m-thick film), which were up to 44% crystalline, were characterised. Two different modalities of temperature diffusivity based on: 1) a resistance change and 2) micro-thermocouple detected modulation of a heat wave, were used for the polymer films with cross-sections of ∼ 100 μ m thickness. Twice different in-plane α ‖ and out-of-plane α ⊥ temperature diffusivities were directly determined with high fidelity: α ‖ = 2 . 12 × 10 − 7 m 2 /s and α ⊥ = 1 . 13 × 10 − 7 m 2 /s. An amorphous polyethylene terephthalate (PET) fiber was measured for comparison α ‖ = 1 . 15 × 10 − 7 m 2 /s. This work provides an example of a direct contact measurement of thermal properties of nanocellulose composite films. The thermal diffusivity, which is usually high in strongly interconnected networks and crystals, was investigated for the first time in this composite.

We fabricate large-area atomically thin MoS₂ layers through the direct transformation of crystalline molybdenum trioxide (MoO₃) by sulfurization at relatively low temperatures. The obtained MoS₂ sheets are polycrystalline (~10-20 nm single-crystal domain size) with areas of up to 300×300 µm² with 2-4 layers in thickness and show a marked p-type behaviour. The synthesized films are characterized by a combination of complementary techniques: Raman spectroscopy, X-ray diffraction, transmission electron microscopy and electronic transport measurements.

Keywords: Tendon injuries; Mallet finger; Suture techniques

The carbonation of industrial calcium-rich byproducts such as steel slag demonstrates significant potential for CO2 sequestration. This technique aids in reducing carbon emissions while also promoting waste recycling. Despite its advantages, gaps remain in understanding how steel slag characteristics and operational parameters influence the carbonation process, as well as the underlying mechanism of direct aqueous carbonation. We evaluated the carbonation performance of three types of steel slag at temperatures below 100°C using a gas–liquid–solid reaction system. The slag with the highest CO2 sequestration capacity was chosen for a systematic evaluation of the effects of operating conditions on carbonation efficiency. Thermodynamic analysis indicated that the reactivity of CaO and Ca(OH)2 with CO2 exceeded that of CaO•SiO2 and 2CaO•SiO2. Under conditions of 85°C, a particle size less than 75 μm, an initial CO2 pressure of 0.5 MPa, a liquid-to-solid ratio of 5 mL/g, and a stirring speed of 200 rpm, the steel slag achieved a sequestration capacity (K) of 283.5 gCO2/kg and a carbonation efficiency (ζCa) of 51.61%. Characterization of the slag before and after carbonation using X-ray diffraction, SEM‒EDS, thermogravimetric analysis, and Fourier transform infrared spectrometry confirmed the formation of new carbonates. Mechanistic analysis revealed that the rate-limiting step initially involved the mass transfer of CO2, transitioning to Ca2+ mass transfer as time progressed. Our research provides a viable technique for CO2 capture and a beneficial approach for reutilizing waste steel slag. Furthermore, solid residues after capturing CO2 have the potential for conversion into carbon-negative building materials, offering a sustainable strategy for steel companies and other enterprises with high carbon emissions.

New families of direct serendipity and direct mixed finite elements on general planar, strictly convex polygons were recently defined by the authors. The finite elements of index r are H1 and H(div) conforming, respectively, and approximate optimally to order r+1 while using the minimal number of degrees of freedom. The shape function space consists of the full set of polynomials defined directly on the element and augmented with a space of supplemental functions. The supplemental functions were constructed as rational functions, which can be difficult to integrate accurately using numerical quadrature rules when the index is high. This can result in a loss of accuracy in certain cases. In this work, we propose alternative ways to construct the supplemental functions on the element as continuous piecewise polynomials. One approach results in supplemental functions that are in Hp for any p≥1. We prove the optimal approximation property for these new finite elements. We also perform numerical tests on them, comparing results for the original supplemental functions and the various alternatives. The new piecewise polynomial supplements can be integrated accurately, and therefore show better robustness with respect to the underlying meshes used.

We discuss two methods to detect the presence and location of a person in a small-scale room and compare the performances. The first method is Direct Intersection, which determines a coordinate point based on the intersection of spheroids defined by observed distances of high-intensity reverberations. The second method, Sonogram analysis, overlays all channel’s room impulse responses to generate an intensity map for the observed environment. We demonstrate that the former method has lower computation complexity and higher accuracy for small numbers of channels, while the latter performs more robustly.

Laser Direct Writing (LDW), also known as 3D multi-photon laser lithography of resins, is a promising technique for fabricating complex free-form elements, including micro-optical functional components. Regular organic or hybrid (organic-inorganic) resins are often used, with latter exhibiting better optical characteristics, as well as having the option to be heat-treated into inorganic glass-like structures, particularly useful for resilient micro-optics. While this work is a continuation of SZ2080™ calcination development , the Laser-Induced Damage Threshold (LIDT) of such sol-gel-derived glass micro-structures, particularly those that undergo heat treatment, has not been well-characterized. In this pilot study, we investigated the LIDT using the Series-on-One (S-on-1) protocol of functional micro-lenses produced via LDW and subsequently calcinated. Our results demonstrate that the LIDT can be significantly increased, even multiple times, by this approach, thus enhancing the resilience and usefulness of these free-form micro-optics. This work represents the first investigation in terms of LIDT into the impact of calcination on LDW produced sol-gel-derived glass micro-structures, and provides important insights for the development of robust micro-optical devices.

This paper investigates the effect of Fe contamination on the microstructure and mechanical properties of Al-7Si-0.7Mg-Fe2.5 alloy processed by Laser Powder Bed Fusion (LPBF) and heat treated in two different conditions: (1) Solution Heat Treatment (SHT) at 520 °C, followed by artificial ageing at 160 °C (T6), and (2) Direct Artificial Ageing of the as-printed material at 160 °C (DAA). Microstructural characterization was carried out by Optical Microscopy (OM), X-Ray Diffraction (XRD), Scanning Electron Microscopy (SEM), and Transmission Electron Microscope (TEM). Mechanical characterization was carried out by tensile tests at room temperature. The formation of fine AlSiFe phases such as α-AlFeSi, β-AlFeSi, and π-Al8Si6Mg3Fe had no deleterious effect on the mechanical properties compared to previous studies for AlSIMg alloys without Fe. However, compared to the as-printed condition, the T6 heat treatment decreased the ultimate tensile strain significantly, while the elongation to the fracture presented a slight improvement.

ChatGPT is an AI language model trained on vast amounts of text data, including scientific papers, providing a comprehensive understanding of catalysis. However, its reliability in catalysis research is unknown. To evaluate reliability, we compared a ChatGPT-generated review article on heterogeneous catalysts for higher alcohols synthesis by CO₂ hydrogenation to published peer-reviewed papers. Although the ChatGPT review article covers most necessary parts, it lacks sufficient discussion of the reaction mechanism. The core sections are too general, being not specific enough to the topic, and contain errors. The lack of citations further increases unreliability. While ChatGPT can provide much content on catalysis, it is insufficient and inaccurate for research on specific topics.

This paper provides the solution to understanding the hitherto unknown writing system used for the manuscript listed as MS 408 at the Beinecke Library, Yale University. The writing system uses symbols, punctuation, grammar and language that are each unique. The manuscript is not encrypted, in the sense that its author made an effort to conceal the contents of the manuscript, as has been presumed by some scholars. Instead, it is code only in the sense that the modern reader needs to be versed in the calligraphic and linguistic rules to be able to translate and read the texts. Furthermore, in discovering its writing system, it became apparent that the manuscript is of invaluable importance to the study of the evolution of the Romance languages and the scheme of Italic letters and associated punctuation marks now commonplace in those and other modern languages. In short; it is revealed to be the only known document both written in Vulgar Latin, or proto-Romance, and using proto-Italic symbols. The original title for the manuscript, given by its female author, is: What one needs to be sure to acquire for the evils set in one’s fate. It is a book offering homeopathic advice and instruction to women of court on matters of the heart, of sexual congress, of reproduction, of motherhood and of the physical and emotional complications that can arise along the way through life. The manuscript has now been dated to the year 1444 and the location of its creation has been pinpointed to the court of Castello Aragonese, on the island of Ischia: as expounded in the companion paper Linguistically Dating and Locating Manuscript MS408: http://ling.auf.net/lingbuzz/003808.

Mode locked pulse generation has been reported using both active and passive mode locking schemes. Active mode locking technique has been proven to be an effective way to generate high-repetition-rate pulses by incorporating a modulator inside the laser cavity. Compared to actively mode locked lasers, passively mode locked lasers can generate pulse train at ultrashort pulse width but with relatively lower repetition rate. Thus, it is a brilliant idea to build a hybrid mode locked system combining both active and passive mode lockers. In this review, several hybrid mode locked fiber ring laser systems are discussed and summarized. Hybrid mode locking is a promising method to generate high speed ultrashort optical pulses for fiber-optic telecommunication system.

Axial resolution is one of the most important characteristics of a microscope. In all microscopes, a high axial resolution is desired in order to discriminate information efficiently along the longitudinal direction. However, when studying thick samples that do not contain laterally overlapping information, a low axial resolution is desirable as information from multiple planes can be recorded simultaneously from a single camera shot instead of plane-by-plane mechanical refocusing. In this study, we increased the focal depth of an infrared microscope non-invasively by introducing a binary axicon fabricated on barium fluoride substrate close to the sample. Preliminary results of imaging thick and sparse silk fibers showed an improved focal depth with a slight decrease in lateral resolution and increase in background noise.

Laser machining by ultra-short (sub-ps) pulses at high intensity offers high precision, high throughput in terms of area or volume per unit time, and flexibility to adapt processing protocols to different materials on the same workpiece. Here we consider the challenge of optimization for high throughput: how to use the maximum available laser power and larger focal spots for larger ablation volumes by implementing a fast scan. This implies the use of high-intensity pulses approaching ∼PW/cm2 at the threshold where tunnelling ionization starts to contribute to overall ionization. A custom laser micromachining setup was developed and built to enable high speed, large area processing and easy system reconfiguration for different tasks. The main components include laser, stages, scanners, control system, and software. Machining of metals such as Cu, Al, or stainless steel, and fused silica surfaces at high-fluence and high-exposure doses at high scan speeds up to 3 m/s were tested for the fluence scaling of ablation volume, which was found to be linear. Modified surfaces are color-classified for their appearance, which is dependent on surface roughness and chemical modification. Such colour-coding can be used as a feedback parameter for industrial process control.