Amorphous germanium films on non-refractory glass substrates were annealed by ultrashort near-infrared (1030 nm, 1.4 ps) and mid-infrared (1500 nm, 70 fs) laser pulses. Crystallization of germanium irradiated at a laser energy density (fluence) range from 25 to 400 mJ/cm2 under single-shot and multi-shot conditions was investigated using Raman spectroscopy. The dependence of the fraction of the crystalline phase on the fluence was obtained for picosecond and femtosecond laser annealings. The regimes of almost complete crystallization of germanium films over the entire thickness are obtained (from the analysis of Raman spectra with excitation of 785 nm laser). The possibility of scanning laser processing is shown, which can be used to create films of micro and nanocrystalline germanium on flexible substrates.

The ability to control the temperature distribution T(t,r) and the rate of temperature change Rt,r inside glasses is important for their microstructuring. The lattice temperature is considered at time t, exceeding the electron-phonon thermalization time, and at a distance r from the center of the model spherical heating zone. In order to describe thermal excitations, the heat capacity of glasses must be considered as a function of time due to its long-term relaxation. A method for analytical calculation of T(t,r) and R(t,r) for glasses with dynamic heat capacity cdyn(t) is proposed. It is shown that during laser microstructuring the local cooling rate -R(t,r) significantly depends on the time dispersion of cdyn(t). It has been established that at the periphery of the model heating zone of the laser beam focus, the local cooling rate can reach more than 1011 K/s. Strong cooling rate gradients were found at the periphery of the heating zone, affecting the microstructure of the material. This effect is significantly enhanced by the time dispersion of cdyn(t). The effect associated with this time dispersion is significant even well above the glass transition temperature Tg, since even short relaxation times of the dynamic heat capacity cdyn(t) are significant.

Three-dimensional nanocomposite networks consisting of percolated Si nanowires in a SiO₂ matrix, Si:SiO₂, were studied. The structures were obtained by reactive ion beam sputter deposition of SiO_x (x ≈ 0.6) thin films at 450 °C and subsequent crystallization using conventional oven as well as millisecond line focus laser annealing. Rutherford backscattering spectrometry, Raman spectroscopy, X-ray diffraction, cross-sectional and energy-filtered transmission electron microscopy were applied for sample characterization. While oven annealing resulted in a mean Si wire diameter of 10 nm and a crystallinity of 72 % within the Si volume, almost single-domain Si structures with 30 nm in diameter and almost free of amorphous Si were obtained by millisecond laser application. The structural differences are attributed to the different crystallization processes: Conventional oven tempering proceeds via solid state, millisecond laser application via liquid phase crystallization of Si. The 5 orders of magnitude larger diffusion constant in the liquid phase is responsible for the three times larger Si nanostructure diameter. In conclusion, laser annealing offers not only significantly shorter process times but moreover a superior structural order of nano-Si compared to conventional heating.

Crystallization often occurs in the laser welding of amorphous alloys, reducing the amorphous alloys’ properties. So, it is necessary to simulate the temperature field curve of the welding area by computer and then determine the power and laser moving speed of laser welding. In this paper, the temperature field curve of Zr41.2Ti13.8Cu12.5Ni10Be22.5(Vit1) amorphous alloy in laser welding is obtained by finite element analysis. The continuous heating curve (CHT) of Vit1 is fitted by the Vogel-Fulcher-Tammann (VFT) equation and the Kissinger equation. If the temperature field curve intersects with the CHT curve, crystallization occurs. The experiment results show that the VFT equation can be used to predict the crystallization of Vit1 better in laser welding. The tem-perature and welding time are increased by using low welding speed. Therefore, the temperature of the weld zone cannot fall in time, resulting intersection of the temperature field curve and the CHT curve. So, crystallization can be avoided if the welding speed is controlled within a rea-sonable range, and the highest temperature is kept under the CHT curve.

Optical coherence tomography (OCT) can help in the diagnosis and treatment of infectious keratitis, but it has not been studied in cases occurring after corneal refractive surgery procedures such as femtosecond laser in situ keratomileusis (FS-LASIK) and keratorefractive lenticule extraction (KLEx). In these procedures a surgical interface is created, where infections usually start, thus determining a different OCT pattern compared to non-surgical infections, which instead begin in the corneal surface. A total of 4 cases of post-refractive surgery infectious keratitis are reported (2 after FS-LASIK and 2 after KLEx), in which the OCT identified an initial infiltrate in the interface, followed by interface inflammation. In 1 case after FS-LASIK, interface fluid accumulation occurred. In 1 case after KLEx, diffuse interface inflammation led to stromal reabsorption, later compensated by stromal reformation and epithelial hyperplasia, well documented by OCT.

Sodium-phosphate-based glass-ceramics (GCs) are promising materials for a wide range of applications, including solid-state sodium-ion batteries, microelectronic packaging substrates, and humidity sensors. This study investigates the impact of 24-hour heat-treatments at varying temperatures on Na-Ge-P glass, with a focus on (micro)structural, electrical, and dielectric properties of prepared GCs. Various techniques such as powder X-ray diffraction (PXRD), infrared spectroscopy-attenuated total reflection (IR-ATR), and scanning electron microscopy-energy dispersive spectroscopy (SEM-EDS) are employed. With the elevation of heat-treatment temperature, crystallinity progressively rises; at 450 °C, the microstructure retains amorphous traits featuring nanometric grains, whereas at 550 °C, heat-treatment results in fully crystallized structures characterized by square-shaped micron-scale grains of NaPO3. The insight into the evaluation of electrical and dielectric properties is provided by Solid-State Impedance Spectroscopy (SS-IS), revealing a strong correlation with the conditions of controlled crystallization and observed (micro)structure. The glass-ceramic heat-treated at 450 °C achieves the highest DC conductivity of 2.30×10–8 Ω–1 cm–1 at 393 K. As the heat-treatment temperature rises, the crystallization of the NaPO3 phase depletes the glass matrix of mobile Na+ ions, resulting in a reduction in DC conductivity. Dielectric parameters also decrease with rising heat-treatment temperature, with the glass-ceramic heat-treated at 550 °C displaying the lowest permittivity of 19.37 and the dielectric loss of 0.008. This research uncovers the intricate relationship between heat-treatment conditions and material properties, emphasizing that controlled crystallization allows for precise modifications to microstructure and phase composition within remaining glassy phase, ultimately facilitating fine-tuning of material properties.

In this project, four of fibers Bragg gratings were fabricated by injecting different volumes of liquids (star line Glass Mechanix optical adhesive material, olive oil diluted with ethanol) into the hollow core fiber. The amplitude splitting interferometric technique with a high resolution specially designed translation stage was used for the fabrication process. The fabrication was done using ultraviolet laser operated at wavelength 405nm. The fabricated Bragg length of the four fibers is equal to 3.8 cm. The results presented fiber Bragg grating (FBG) with successful fabrication at 653.3 nm Bragg reflected wavelength.

Laser in situ keratomileusis (LASIK) is the gold standard in the surgical correction of refractive errors on the cornea. It entails the creation of a superficial hinged corneal flap by a femtosecond laser, ablation of the underlying stromal bed by an excimer laser, and reposition of the flap. The corneal flap can be build in a 2-dimension (2D) fashion with tapered edges, or in a 3-dimension (3D) fashion, with angled sidecut. The latter reduces the risk of flap dislocation and infiltration of epithelial cells. This retrospective study compares with optical coherence tomography 3D and 2D flaps, and respective intra- and early post-operative complications. Four hundred consecutive eyes were included, 200 for each group. In the 3D group, the mean edge angle was 92°. The procedure was in average 5.2 seconds slower in the 3D group (p=0). Non visually significant flap folds were found in 13 eyes of the 2D group and in 7 eyes of the 3D group (p= 0.17). An intracorneal opaque bubble layer induced by laser photodisruption was more commonly observed in the 3D group (9 eyes vs. 2; p=0.03). In conclusion, the creation of a LASIK flap by a 3D-femtosecond laser cut was safe and effective.

In the theoretical treatment of crystallization it is commonly assumed that relaxation processes of the liquid proceed fast as compared to crystal nucleation and growth processes. Actually, it is supposed that the liquid is located always in the metastable state corresponding to the current values of pressure and temperature. However, near and below the glass transition temperature, Tg, this condition is commonly not fulfilled. In such cases, in the treatment of crystallization, deviations of the state of the liquid from the respective metastable equilibrium state have to be accounted for in determining the kinetic coefficients governing the crystallization kinetics, the thermodynamic driving force of crystallization, and the surface tension of the aggregates of the newly evolving crystal phase including the surface tension of critical clusters affecting considerably the crystal nucleation rate. These factors may considerably influence the course of the overall crystallization process. A theoretical analysis of the resulting effects is given in the present paper by numerical solutions of the J(ohnson)–M(ehl)–A(vrami)–K(olmogorov)–equation employed as the tool to model the overall crystallization kinetics and by analytical estimates of the crystallization peak temperatures in dependence on cooling and heating rates. The results are shown to be in good agreement with experimental data. Possible extensions of the theory to be explored in future analysis are anticipated.

Crystalline silver thin layers were obtained by high-energy pulsed laser ablation without heating of the deposition substrate. The fluid Plateau-Rayleigh (PRI), Rayleigh – Taylor (RTI) and Richtmyer – Meshkov (RMI) instabilities, as well as crown splash induced during pulsed laser deposition (PLD) in high energy regime, resulting in ring and pearl shaped structures, offer the benefit of increased sorption surface. These morphological structures obtained for the silver thin layers make them of interest for catalytic applications. The study presented with this work addresses both the fundamental and applied issues on the morphological structures obtained for the silver thin layer and their catalytic function in organic processes. In this sense, the catalytic action of the thin silver layer was highlighted by modifications of the Reactive Blue 21 dye (C.I.) in aqueous solution with sodium bicarbonate. Specific investigations and analyzes were carried out by electron microscopy and elemental analysis (SEM-EDX), atomic force microscopy (AFM) and profilometry, mass spectrometry, ablation plasma diagnosis, diffractograms (XRD), as well as IR spectroscopy (FTIR). In addition to the experimental investigation and analyzes, simulation of the ionization energy threshold was conducted in COMSOL for complementary evaluation on the involved processes and phenomena.

The stability properties of the Hill equation are discussed, and especially those of the Mathieu equation that characterize ion motion in electrodynamic traps. The solutions of the Mathieu equation for a trapped ion are characterized by using the Floquet theory and Hill's Method solution, which yields an infinite system of linear and homogeneous equations whose coefficients are recursively determined. Stability is discussed for parameters $a$ and $q$ that are real. Characteristic curves are introduced naturally by the Sturm-Liouville problem for the well known even and odd Mathieu equations $ce_m(z,q)$ and $se_m(z,q)$. We illustrate the stability diagram for a combined (Paul and Penning) trap and represent the frontiers of the stability domains for axial and radial motion. In case of a Paul trap the stable solution corresponds to a superposition of harmonic motions. The problem of evaluating the maximum amplitudes of stable oscillations for the ideal conditions (taken into consideration) is also approached. Anharmonic corrections are discussed within the frame of the perturbation theory, while the frontiers of the modified stability domains are determined as a function of the chosen perturbation parameter. The results apply to 2D and 3D ion traps used for different applications in quantum engineering, among which optical clocks, quantum logic and quantum metrology, but not restricted only to these.

This work presents the results regarding the synthesis of tungsten nanoparticles (W NPs) by magnetron sputtering combined with gas aggregation (MSGA) when H2 mixed with Ar is used as working gas, the amount of H2 being increased up to 82%. The results show that up to 40% H2 in discharge the synthesis rate increases over 60 times, rapidly decreasing for over 50% H2 in discharge. The W dust is still produced in H2 dominated discharge (82%), the deposition rate being small but not negligible (20 mg/hour). The obtained WNPs are isolated, with the diameter decreasing from 50 nm to 15 nm when the amount of H2 in discharge is smaller than 41%. Over this value, the particles tend to agglomerate, forming structures similar to film-like deposits. Also, the diameter of the deposited spots on substrates is dependent on the H2 content in discharge. This allows the efficient coating of substrates with dimensions up to 26 mm by translating them in front of the MSGA cluster source exit aperture. Supplementary, for 41% H2 in discharge, the influence of synthetic air leaks (0-5%) in discharge was investigated. The deposition rate decreases rapidly (ceasing for around 4% air in discharge) and the obtained nanoparticles tend to agglomerate (at 2% air content, the dust deposit has the aspect of a near continuous film). Chemical composition investigations show a pronounced tendency of oxidation, nitridation and oxynitride formation in the presence of air leaks.

High-power laser facilities necessitate predicting incremental damage to final optics to identify evolving damage trends. In this study, we propose a surface damage detection method utilizing image segmentation employing ResNet-18, and a damage area estimation network employing U-Net++. Paired sets of online and offline images of optics obtained from a large laser facility is used to train the network. The trends of varying damage could be identified by incorporating additional experimental parameters. A key advantage of the proposed method is that the network can be trained end-to-end on small samples, eliminating the need for manual labeling or feature extraction. The software developed based on these models can facilitate the daily inspection and maintenance of optics in large laser facilities.

This article utilizes the Canny edge extraction algorithm based on contour curvature and the cross-correlation template matching algorithm to extensively study the impact of high-repetition-rate CO2 pulsed Laser on the target extraction and tracking performance of the infrared imaging detector. It establishes a quantified dazzling pattern for lasers on infrared imaging systems. By conducting laser dazzling and damage experiments, a detailed analysis of the normalized correlation between target and dazzling images is performed to quantitatively describe laser dazzling effects. Simultaneously, an evaluation system, including target distance and laser power evaluation factors, is established to determine the dazzling level and whether the target is recognizable. The research results reveal that laser power and target position are crucial factors affecting the detection performance of infrared imaging-guided weapon systems under laser dazzling. Different laser powers are required to successfully interfere with the recognition algorithm of infrared imaging-guided weapons at different distances. And laser dazzling will produce a lot of false edge information, which seriously affects the performance of pattern recognition algorithm. In laser damage experiments, the detector experienced functional damage, with a quarter of the image displaying as completely black. The energy density threshold required for functional damage to the detector is approximately 3 J/cm2. The dazzling assessment conclusions also apply to evaluating damage results. Finally, the proposed evaluation formula aligns with experimental results, objectively reflecting the actual impact of laser dazzling on the target extraction and tracking performance of infrared imaging systems. This study provides an in-depth and accurate analysis for understanding the influence of lasers on the performance of infrared imaging-guided weapons.

The amorphous Fe77Cu1Si13B9 ribbons were treated with pulsed laser interference heating (PLIH). It was confirmed here that the use of the laser heating process allowed for obtaining two-dimensional crystallised micro-areas, periodically distributed (at a distance of 17µm) on the surface of the amorphous ribbons. The correlation between structural changes (SEM, TEM, HRTEM) and the distribution of magnetic field lines of heated amorphous Fe77Cu1Si13B9 (FeCuSiB) ribbons is presented. Particular attention is paid to structure changes in micro-areas where, by controlling the laser interference heating process, partial crystallisation of amorphous alloys and the formation of clusters or single nanocrystallites (α-Fe(Si)) embedded in an amorphous matrix are given. The addition of copper to the FeSiB alloy promoted inhibition of grain growth. Electron holography of micro-areas confirmed shifts of the magnetic field lines in the areas of nanocrystallites, the presence of which in the structure caused magnetisation of the surrounding amorphous matrix.

Crystallization of glass through conventional thermal annealing in a furnace is a well-understood process. However, crystallization by femtosecond (fs) laser brings another dimension to this process. The pulsed nature of the irradiation necessitates a reevaluation of parameters for optimal crystallization and to understand the particularities in the case of using fs laser. This includes adjusting the laser pulse energy, the repetition rate, and the writing speed to either initiate nucleation or achieve substantial crystal growth. Therefore, a key challenge to this work is to establish reliable calculations for understanding the relation of the size of the crystallized region with respect to an ongoing transition (e.g., solid-to-solid, liquid-to-solid), and accounting for the aforementioned laser parameters. In this context and based on previous work, we simulate a temperature distribution (in space and time) to model the thermal treatment at any point in the glass. By setting the condition that the temperatures are between the glass transition and melting temperature, we can deduce the crystallized region size to be compared with experimental observations. For that purpose, the knowledge of the beam width at the focal point and of the absorbed beam energy fraction are critical inputs that were extracted from experiments found in the literature. After that, management of the crystallization process and the width of the crystallization line can be achieved according to pulse energy e.g. crystallite size, and also the effect of the scanning speed can be understood. Among the main conclusions to highlight, we disclose the laser conditions that determine the extent of the crystallized area and deduce that it is never interesting to increase the pulse energy too much but rather the repetition rate for uniform crystallized line.

The achievement of size uniformity and monodispersity in perovskite quantum dots (QDs) requires the implementation of precise temperature control and the establishment of optimal reaction conditions. Nevertheless, the accurate control of a range of reaction variables represents a considerable challenge. This study addresses the aforementioned challenge by employing manganese (Mn) doping to achieve size uniformity in CsPbBr₃ perovskite QDs without the necessity for precise control of the reaction conditions. By optimizing the Mn:Pb ratio, it is possible to successfully dope CsPbBr₃ QDs with appropriate concentrations of Mn²⁺ and achieve a uniform size distribution. The spectroscopic measurements on single QDs indicate that the appropriate Mn²⁺ concentrations can result in a narrower spectral linewidth, a longer photoluminescence (PL) lifetime, and a reduced biexciton Auger recombination rate, thus positively affecting the PL properties. This study not only simplifies the size control of perovskite QDs, but also demonstrates the potential of Mn-doped CsPbBr₃ QDs for narrow linewidth light-emitting diode applications.

In this paper the one-to-one correspondences and equivalences between ideals, primals, filters and grills are introduced. It is shown the local functions and the topological spaces induced by them are the same. From this point of view, the topological properties with respect to one topology can be derived from topological properties valid in the corresponding topology.

Amorphous silicon (α-Si) film present an inexpensive and promising material for optoelectronic and nanophotonic applications. Its basic optical and optoelectronic properties are known to be improved via phase transition from amorphous to polycrystalline phase. Infrared femtosecond laser radiation can be considered as a promising nondestructive and facile way to drive uniform in-depth and lateral crystallization of α-Si films that are typically opaque in UV-visible spectral range. However, so far only a few studies reported on utilization of near-IR radiation for laser-induced crystallization of α-Si providing no information regarding optical properties of the resultant polycrystalline Si films. The present work demonstrates efficient and gentle single-pass crystallization of α-Si films induced by their direct irradiation with near-IR femtosecond laser pulses coming at sub-MHz repetition rate. Comprehensive analysis of morphology and composition of laser-annealed films by atomic-force microscopy, optical, micro-Raman and energy-dispersive X-ray spectroscopy, as well as numerical modeling of optical spectra, confirmed efficient crystallization of α-Si and high-quality of the obtained films. Moreover, we highlight localized laser-driven crystallization of α-Si as a promising way for optical information encryption, anti-counterfeiting and fabrication of micro-optical elements.

The present work investigates primarily the morphology evolution of the body-centered-cubic (BCC)/B2 phases in AlxNiCoFeCr high-entropy alloys (HEAs) with increasing Al content, which has been neglected so far. There exist two types of microscopic morphologies of BCC and B2 phases in this HEA series: one is the weave-like morphology induced by the spinodal decomposition, and the other is the microstructure of a spherical disordered BCC precipitation on the ordered B2 matrix that appears in HEAs with a much higher Al content. The shape of coherent precipitates is found to be closely related to the lattice misfit between BCC and B2 phases, which is sensitive to Al. The mechanical properties, including the compressive yielding strength and microhardness of the AlxNiCoFeCr HEAs, are also discussed in light of the concept of the valence electron concentration (VEC).

This study investigated the effects of fish oil (FO) treatment, particularly enriched with eicosapentaenoic acid (EPA), on obesity induced by a high-fat diet (HFD) in mice. The investigation focused on elucidating the impact of FO on epigenetic modifications in white adipose tissue (WAT) and the involvement of adipose-derived stem cells (ASCs). C57BL/6j mice were submitted to a control diet or a HFD for 16 weeks, treated (or not) with FO for the last 8 weeks. WAT was removed for RNA and protein extraction, while ASCs were isolated, cultured, and treated with Leptin. All samples were analyzed using functional genomics tools, including PCR-array, RT-PCR and Western Blot assays. Mice receiving HFD displayed increased body mass, fat accumulation, and altered gene expression associated with WAT inflammation and dysfunction. FO supplementation attenuated these effects, a potential protective role against HFD-induced obesity. Analysis of H3K27 revealed HFD-induced changes in histone, which were partially reversed by FO treatment. The study further explored leptin signaling in ASCs, suggesting a potential mechanism for ASC dysfunction in the leptin-rich environment of obese WAT. Overall, FO supplementation demonstrated efficacy in mitigating HFD-induced obesity, influencing epigenetic and molecular pathways, and shedding light on the role of ASCs and leptin signaling in WAT dysfunction associated with obesity.

In recent years, tremendous progress has been made in the development of rare-earth ion doped tellurite glass laser sources, ranging from watt and multiwatt level fiber lasers to nanowatt level microsphere lasers. Significant success has been achieved in extending the spectral range of tellurite fiber lasers generating at wavelengths beyond 2 μm as well as in theoretical understanding. This review is aimed at discussing the state of the art of neodymium-, erbium-, thulium-, and holmium-doped tellurite glass fiber and microsphere lasers.

Balance requires constant adjustments in muscle activation to attain force steadiness. Creating appropriate training can be challenging. The purpose of this study was to examine the effects of two weeks front squat instability training using a water-filled training tube on force steadiness during an instability challenge. Control (CON, n= 13) and experimental (EXP, n=17) subjects completed pre and post testing for EMG variability by completing one set of 10 repetitions with a stable and unstable training tube. Electrodes were placed bilaterally on the anterior deltoid, paraspinal and vastus lateralis muscles. CON subjects completed 2 weeks of training using a stable training tube, while EXP subjects trained with a water-filled instability tube. EMG data were integrated for each contraction and force steadiness computed using the natural log of coefficient of variation. CON results showed no changes in force steadiness for any condition. EXP showed significant reductions in EMG activation variability across all muscles. These results indicate a significant training effect in reducing muscle activation variability in subjects training with a water-filled instability training device. Improvements seen in these healthy subjects supports development of training implements for a more clinical population to help improve force steadiness.

Isotope detection and identification is paramount in many fields of science and industry, such as in the fusion and fission energy sector, in medicine and material science, and in archeology. The isotopic information provides fundamental insight on the research questions related to these fields as well as insight on product quality and operational safety. However, isotope identification with the established mass-spectrometric methods is laborious and requires laboratory conditions. In this work, Microwave-Assisted Laser-Induced Breakdown Spectroscopy (MW-LIBS) is introduced for isotope detection and identification utilizing radical and molecular emission. The approach is demonstrated with stable B and Cl isotopes in solids and H isotopes in liquid using emission from BO and BO2, CaCl, and OH molecules, respectively. MW-LIBS utilizes the extended emissive plasma lifetime and molecular emission signal integration times up to 900 s to enable use of low ~4 mJ ablation energy without compromising signal intensity and, consequently, sensitivity. On the other hand, long plasma lifetime gives time for molecular formation. Increase in the signal intensity towards the late microwave-assisted plasma was prominent in BO2 and OH emission intensities. As MW-LIBS is online-capable and requires minimal sample preparation, it is an interesting option for isotope detection in various applications.

Laser-induced graphene (LIG) has gained considerable attention recently due to its unique properties and potential applications. In this study, we investigate using LIG in polyimide (PI) as a material for antenna applications. The LIG-PI composite material was prepared by a facile picosecond laser (1064 nm) irradiation process, which resulted in a conductive graphene network within the PI matrix. Furthermore, LIG formation was confirmed by Raman spectroscopy and sheet resistance measurements. Finally, a patch antenna from LIG for 2.45 GHz microwaves was simulated, produced and tested. These findings suggest that LIG-PI composites have great potential for use in high-frequency electronic devices and can provide a new avenue for the development of flexible and wearable electronics.

We report on the application of femtosecond laser micromachining to the fabrication of complex glass microdevices, for high-order harmonic generation in gas. The three-dimensional capabilities and extreme flexibility of femtosecond laser micromachining allow us to achieve accurate control of gas density inside the micrometer interaction channel. This device gives a considerable increase in harmonics generation efficiency if compared with traditional harmonic generation in gas jets. We propose different chip geometries that allow to control the gas density and driving field intensity inside the interaction channel to achieve quasi-phase matching conditions in the harmonic generation process. We believe that these glass micro-devices will pave the way to future downscaling of High-order Harmonic Generation beamlines.

Our hypothesis that controlled ozone applications interfere into the redox balance of the biological organism (first published in 1998 with a preclinical trial on protecting the liver from CCl4 intoxication), has been verified over the last 2 decades in reactive oxygen species (ROS)-induced mitochondrial pathologies, such as rheumatoid arthritis, osteoarthritis, aging processes, diabetes-2 and in prevention of intoxications. Low-dose ozone acts as a redox bioregulator: The restoration of the disturbed redox balance is comprehensible in a number of preclinical and clinical studies by a remarkable increase of the antioxidant repair markers, here mainly shown as glutathione increase and a reduction in oxidative stress markers, mainly malondialdehyde. The mechanism of action is shown, relevant data are displayed, evaluated and comprehensively discussed: The repair side of the equilibrium increases by 21% up to 140% compared to the non-ozone treated groups and depending on the indication; the stress markers are simultaneously reduced, the redox system regains its balance.

Within the spectra of lanthanide atoms quite often overlapping spectral lines (blends) are observed. On the example of complicated blend situations within Pr I and La I it is shown that in such cases a combination of optogalvanic and laser-induced fluorescence detection is necessary to find all transitions contributing to the observed spectral signature.

Laser machining by ultra-short (sub-ps) pulses at high intensity offers high precision, high throughput in terms of area or volume per unit time, and flexibility to adapt processing protocols to different materials on the same workpiece. Here we consider the challenge of optimization for high throughput: how to use the maximum available laser power and larger focal spots for larger ablation volumes by implementing a fast scan. This implies the use of high-intensity pulses approaching ∼PW/cm2 at the threshold where tunnelling ionization starts to contribute to overall ionization. A custom laser micromachining setup was developed and built to enable high speed, large area processing and easy system reconfiguration for different tasks. The main components include laser, stages, scanners, control system, and software. Machining of metals such as Cu, Al, or stainless steel, and fused silica surfaces at high-fluence and high-exposure doses at high scan speeds up to 3 m/s were tested for the fluence scaling of ablation volume, which was found to be linear. Modified surfaces are color-classified for their appearance, which is dependent on surface roughness and chemical modification. Such colour-coding can be used as a feedback parameter for industrial process control.

The self-assembly is an intriguing process of great importance in general soft matter and thus re-ceives an ever-growing scientific interest. Its most trivial example is the entropy-driven crystalli-zation of hard spheres. Past works have established the similarities and differences in the phase behavior of monomers and chains made of hard spheres. In the present work, inspired by the dif-ference in the melting points of the pure components, we study, through Monte Carlo simulations, the phase behavior of athermal mixtures composed of fully flexible polymers and individual monomers of uniform size. We analyze how the relative number fraction and the packing density affect crystallization and the established ordered morphologies. A synergetic effect is observed in the crystallization leading to synchronous crystallization of the two species. Structural analysis of the resulting ordered morphologies shows perfect mixing and thus no phase separation, which could split the system into polymer-rich and monomer-rich domains. Due to the constraints imposed by chain connectivity, the local environment of the individual spheres is systematically more spherical and more symmetric compared to the one of spheres belonging to chains. In general, increasing polymer content leads to reduction of the degree of crystallinity. According to the present findings, relative concentration is another determining factor to control the phase behavior of hard colloidal systems based on polymers.

Materials engineering based on metal oxides for manipulating the solar spectrum and producing solar energy have been under intense investigation over the last years. In this work, we present NiO thin films double-doped with niobium (Nb) and nitrogen (N) as cation and anion dopants (NiO:(Nb,N)) to be used as p-type layers in all oxide transparent solar cells. The films were grown by sputtering a composite Ni-Nb target on room-temperature substrates in plasma containing 50% Ar, 25% O2 and 25% N2 gases. The existence of Nb and N dopants in the NiO structure was confirmed by the Energy Dispersive X-Ray and X-Ray Photoelectron Spectroscopy techniques. The nominally undoped NiO film, which was deposited by sputtering a Ni target and used as the reference film, was oxygen-rich, single-phase cubic NiO, having a visible transmittance of less than 20%. Upon double doping with Nb and N the visible transmittance of NiO:(Nb,N) film increased to 60%, which was further improved after thermal treatment to around 85%. The respective values of the direct band gap in the undoped and double-doped films were 3.28 eV and 3.73 eV just after deposition and 3.67 eV and 3.76 eV after thermal treatment. The changes in the properties of the films such as structural disorder, direct and indirect energy band gaps, Urbach tail states and resistivity were correlated with the incorporation of Nb and N in their structure. The thermally treated NiO:(Nb,N) film was used to form a diode with a spin-coated two-layer, mesoporous on top of a compact, TiO2 film. The NiO:(Nb,N)/TiO2 heterojunction exhibited visible transparency of around 80%, showed rectifying characteristics and the diode’s parameters were deduced using the I-V method. The diode revealed photovoltaic behavior upon illumination with UV light exhibiting a short circuit current density of 0.2 mA/cm2 and open-circuit voltage of 500 mV. Improvements of the output characteristics of the NiO:(Nb,N)/TiO2 UV-photovoltaic by proper engineering of the individual layers and device processing procedures are addressed. Transparent NiO:(Nb,N) films can be potential candidates in all-oxide ultraviolet photovoltaics for tandem solar cells, smart windows and other optoelectronic devices.

Spatially resolved, line-of-sight measurements of aluminum monoxide emission spectra in laser ablation plasma are used with Abel inversion techniques to extract radial plasma temperatures. Contour mapping of the radially deconvolved signal intensity shows a ring of AlO formation near the plasma boundary with the ambient atmosphere. Simulations of the molecular spectra were coupled with the line profile fitting routines. Temperature results are presented with simultaneous inferences from lateral, asymmetric radial, and symmetric radial AlO spectral intensity profiles. This analysis indicates that we measured shockwave phenomena in the radial profiles, including a temperature drop behind the blast wave created during plasma initiation.

Birefringence of 3 × 10^-3 is demonstrated inside cross-sectional regions of 100 µm, inscribed by axially stretched Bessel-beam-like fs-laser pulses along the c-axis inside sapphire. A high birefringence and retardance of λ/4 at mid-visible spectral range (green) can be achieved utilizing stretched beams with an axial extension of 30-40 µm. Conditions of laser writing chosen ensure that there are no formations of self-organised nano-gratings. This method can be adopted for the creation of polarisation optical elements and fabrication of spatially varying birefringent patterns for optical vortex generation.

In this paper, the mechanism of combined process of ion beam sputtering (IBS) and HF acid etching on the chemical structure defects of fused silica and its laser damage resistance perfor-mance were investigated. During the removal process of surface material, the sputtering effect causes lattice atoms to detach from their original positions, forming a large number of unsaturated structures on silica surface, which improves the chemical activity of Si and O atoms, accelerates the chemical reaction process between surface atoms and water molecules, increases the content of hydroxyl (OH-) groups in the shallow layer, and enhances the photothermal weak absorption intensity. However, the presence of OH- groups reduces the bonding strength of Si-O, destroys the spatial network structure of silica bulk, and reduces the mechanical strength of silica surface, resulting in a decrease in its laser damage resistance performance. The paper reveals for the first time the mechanism of IBS to change the structure characteristics of silica material, accelerate the surface hydroxylation process, and thereby reduces the laser damage resistance performance. This work provides technical guidance for effectively suppressing chemical structure defects on silica surface and improving laser damage resistance performance of optical components under high-flux laser irradiation.

Three-dimensional (3D) printing has allowed for production of geometrically complex 3D objects with extreme flexibility, which is currently undergoing rapid expansions in terms of materials, functionalities, as well as areas of application. When attempting to print 3D microstructures in glass, femtosecond laser induced chemical etching (FLICE) – which is a subtractive 3D printing technique – has proved itself a powerful approach. Here, we demonstrate fabrication of macro-scale 3D glass objects of large heights up to ~3.8 cm with an identical lateral and longitudinal spatial resolution of ~20 μm. The remarkable accomplishment is achieved by revealing an unexplored regime in the interaction of ultrafast laser pulses with fused silica which results in aberration-free focusing of the laser pulses deeply inside fused silica.

Laser-induced breakdown spectroscopy (LIBS) of pharmaceutical drugs that contain paracetamol is investigated in air and argon atmospheres. Characteristic neutral and ionic spectral lines of various elements and molecular signatures of CN violet and C₂ Swan band systems are observed. The relative hardness of all drug samples is measured as well. Principal component analysis, a multivariate method, is applied in data analysis for demarcation purposes of the drug samples. The CN violet and C₂ Swan spectral radiances are investigated for evaluation of possible correlation of the chemical and molecular structures of the pharmaceuticals. Complementary Raman and Fourier-transform-infra-red spectroscopies are used record molecular spectra of the drug samples. The applicationof the above techniques for the drug screening are important for identification and mitigation of drugs that reveal additives that may cause adverse side-effects.

The trafficking of illegal drugs by criminal networks at borders, harbors, or airports is an increasing issue in public health as these routes ensure the main supply of illegal drugs. The prevention of drug smuggling, including the installation of scanners and other analytical devices to detect ultra-small traces of drugs within a reasonable time frame, remains a challenge. The presented immunosensor is based on a monolithic affinity column with a large excess of immobilized hapten, which traps fluorescently labeled antibodies as long as the analyte cocaine is absent. In the presence of the drug, some binding sites of the antibody will be blocked, which leads to an immediate breakthrough of the labeled protein, detectable by highly sensitive laser-induced fluorescence with the help of a Peltier-cooled complementary metal-oxide-semiconductor (CMOS) camera. Liquid handling is performed with high-precision syringe pumps and microfluidic chip-based mixing devices and flow cells. The biosensor achieved limits of detection of 23 pM (7 ppt) of cocaine with a response time of 90 seconds and a total assay time below 3 minutes. With surface wipe sampling, the biosensor was able to detect 300 pg of cocaine. This immunosensor belongs to the most sensitive and fastest detectors for cocaine and offers near-continuous analyte measurement.

This work examines atomic and molecular signatures in laser-induced plasma in standard ambient temperature and pressure environments, including background contributions to the spectra that depend on the laser pulse-width. Investigations include solids, gases, and nano-particles. Abel inversions of measured line-of-sight data reveal insight into the radial plasma distribution. For nominal 6 nanosecond laser pulses and for pulse-energies in the range of 100 to 800 milli-Joules, expansion dynamics and turbulence due to shock phenomena are elucidated to address local equilibrium details that are frequently assumed in spatially averaged emission spectroscopy. Chemical equilibrium computations reveal temperature dependence of selected plasma species. Specific interests include atomic hydrogen (H) and cyanide (CN). The atomic H spectra, collected following optical breakdown in ultra-high-pure hydrogen and 9:1 mixtures of ultra-pure hydrogen and nitrogen gases, indicate spherical shell structures and isentropic expansion of the plasma kernel over and above the usual shockwave. The recombination radiation of CN emanates within the first 100 nanoseconds for laser-induced breakdown in a 1:1 CO₂:N₂ gas mixture when using nanosecond laser pulses to create the micro-plasma. The micro-plasma is generated using 1064 nm, 150 mJ, 6 ns Q-switched Nd:YAG laser radiation. Measurements of the optical emission spectra utilize a 0.64 m Czerny-Turner type spectrometer and an intensified charge-coupled device.

Magnetic and morphological properties of equiatomic B2-ordered FeRh thin films irradiated with single high-intensity ultrashort laser pulses are investigated. The goal is to elucidate the effect of femtosecond laser ablation on the magnetic properties of FeRh. We employed Scanning Magneto-Optical Kerr Effect (S-MOKE) microscopy to examine the magnetic phase after laser processing, providing high spatial resolution and sensitivity. Our results revealed the appearance of a magneto-optical signal from the bottom of ablation craters, suggesting a transition from antiferromagnetic to ferromagnetic behavior. Fluence-resolved measurements clearly demonstrate that the ablation threshold coincides with the threshold of the antiferromagnet-to-ferromagnet phase transition. The existence of such magnetic phase transition was independently confirmed by temperature-dependent S-MOKE measurements using a CW laser as a localized heat source. Whereas the initial FeRh film displayed a reversible antiferromagnet-ferromagnet phase transition, the laser-ablated structures exhibited irreversible changes in their magnetic properties. This comprehensive analysis revealed the strong correlation between the femtosecond laser ablation process and the magnetic phase transformation in FeRh thin films.

The temporary immersion system bioreactor named GreenTray®[2], [3]presents advantages over the existing ones. Firstly, there is no need to use forceps to move the shoots or plantlets in or out of the recipient, neither the use of scalpel to divide them. Secondly, the basis of the shoot can remain in the GreenTray® and can sprout again in several cycles of growth. These two characteristics reduce the costs in the process of micropropagation. Besides, shoots or plantlets development is enhanced by the aeration of the recipient, thus enriching with CO2 the recipient atmosphere. The chapter describes and provides images and values of interest in (1) the micropropagation process of some commercial Prunus or Pyrus rootstocks; (2) the plantlet growth under autotrophic conditions; and (2) the inoculation of plants with pathogens that reproduce in vitro the symptoms observed in vivo, using the GreenTray® bioreactor.

Brain aging causes a wide variety of changes at molecular and cellular levels, leading to the decline of cognitive functions and increased vulnerability to neurodegenerative disorders. The research aimed at understanding the aging of the brain has made much progress in recent decades. Technological innovations such as single-cell RNA-sequencing (scRNA-seq), proteomic analyses, and spatial transcriptomic analyses have facilitated the research on the dynamic changes occurring within neurons, glia, and other cells along with their impacts on intercellular communication during aging. In this review, we introduce recent trends of how neurons and glia change during aging and discuss the impact of the brain microenvironment such as the blood-brain barrier (BBB).

This work discusses diatomic molecular spectroscopy of laser-induced plasma and analysis of data records, specifically signatures of cyanide, CN. Line strength data from various databases are compared for simulation of the CN, B2Σ+⟶X2Σ+, Δv=0 sequence. Of interest are recent predictions using an astrophysical database, i.e., ExoMol, a laser-induced fluorescence database, i.e., LIFBASE, and a program for simulating rotational, vibrational and electronic spectra, i.e., PGOPHER. Cyanide spectra that are predicted from these databases are compared with line strength data that are in use by the author for the last three decades in the analysis of laser-plasma emission spectra. Comparisons with experimental laser-plasma records are communicated as well, and for spectral resolutions of 33 and 110 picometer. The accuracy of the CN line strength data is better than one picometer. Laboratory experiments utilize 308-nm, 35-picosecond bursts within an overall 1-nanosecond pulse-width, and 1064-nm, 6-ns pulse-width radiation. Experimental results are compared with predictions. Differences of the databases are elaborated for equilibrium of rotational and vibrational modes and at an internal, molecular temperature of the order of 8,000 Kelvin. Applications of accurate CN data include for example combustion diagnosis, chemistry, and supersonic and hypersonic expansion diagnosis. The cyanide molecule is also of interest in the study of astrophysical phenomena.

This work examines atomic and molecular signatures in laser-induced plasma in standard ambient temperature and pressure environments, including background contributions to the spectra that depend on the laser pulse-width. Investigations include solids, gases, and nano-particles. Abel inversions of measured line-of-sight data reveal insight into the radial plasma distribution. For nominal 6 nanosecond laser pulses and for pulse-energies in the range of 100 to 800 mJ, expansion dynamics and turbulence due to shock phenomena are elucidated to address local equilibrium details that are frequently assumed in spatially averaged emission spectroscopy. Chemical equilibrium computations reveal temperature dependence of selected plasma species. Specific interests include atomic hydrogen (H) and cyanide (CN). Atomic hydrogen spectra indicate axisymmetric shell structures and isentropic expansion of the plasma kernel over and above the usual shockwave. The recombination radiation of CN emanates within the first 100 nanoseconds for laser-induced breakdown in a 1:1 CO2:N2 gas mixture when using nanosecond laser pulses to create the micro-plasma. The micro-plasma is generated using 1064 nm, 150 mJ, 6 ns Q-switched Nd:YAG laser radiation. Measurements of the optical emission spectra utilize a 0.64 m Czerny-Turner type spectrometer and an intensified charge-coupled device.

Volumetric modification of transparent materials by femtosecond laser pulses is successfully used in a wide range of practical applications. The level of modification is determined by the locally absorbed energy density, which depends on numerous factors. In this work, it is shown experimentally and theoretically that, in a certain range of laser pulse energies, the peak of absorption of laser radiation for doughnut-shaped (DS) pulses is several times higher than for Gaussian ones. This makes the DS pulses very attractive for material modification and direct laser writing applications. Details of the interaction of laser pulses of Gaussian and doughnut shapes with fused silica obtained by numerical simulations are presented for different pulse energies and compared with the experimentally obtained data. The effect of absorbed energy delocalization with increasing laser pulse energy is demonstrated for both beam shapes while, at relatively low pulse energies, the DS beam geometry provides a stronger local absorption compared to Gaussian one. Implications of a DS pulse action on post-irradiation material evolution are discussed based on thermoelastoplastic modeling.

Background: The prevalence of falls among the older population underscores the imperative of comprehending human adaptations to gait perturbations. Dual-belt treadmills offer a controlled setting for such investigations. The purpose of this study was to examine the effect of acceleration of one belt of the treadmill during three different phases of the gait cycle on kinematic and kinetic parameters and relate these changes to unperturbed gait. Methods: Twenty-one healthy young females walked on a treadmill in a virtual environment, in which five unexpected perturbations were applied to the left belt at the Initial Contact (IC), Mid Stance (MS), and Pre-Swing (PS) phase of the gait cycle. Data from the undisturbed gait and the first disturbance of each trial were extracted for analysis. Results: All perturbations significantly affected the gait pattern, mainly by decreasing the knee extension angle. The perturbation in the IC phase had the most significant effect, resulting in a 248.48% increase in knee flexion torque. The perturbation in the MS phase mainly affected plantar flexion torque, increasing it by 118.18%, while perturbation in the PS phase primarily increased the hip extension torque by 73.02%. Conclusions: The presence of perturbations in the IC and PC phases caused the most aggressive and significant changes in gait parameters.

In the current research work, electrical resistance tomography (ERT) was employed for crystallization process monitoring and visualization. A first-of-its-kind MATLAB-based interactive GUI application “ERT-Vis” is presented. Two case studies involving varied crystallization methods were undertaken. The experiments involving calcium carbonate reactive (precipitative) crystallization for the high conductivity solution-solute media and the cooling crystallization for sucrose crystallization representing the lower conductivity solution-solute combination were designed and performed. The software successfully provided key insights regarding the process progress in both crystallization systems. It could detect and separate the crystal agglomerations in the low as well as high conductivity solutions using visual analytics tools provided. The performance and utility of the software were studied using a software evaluation case study involving domain experts. Participant feedback indicated that ERT-Vis software helps in reconstructing images instantaneously, interactively visualizing, and evaluating the output of the crystallization process monitoring data.

The advancement of performance in the domain of flexible wearable strain sensors has become increasingly significant due to extensive research on laser-induced graphene (LIG). An innovative doping modification technique is required owing to the limited progress achieved by adjusting laser parameters to enhance LIG’s performance. By pre-treating with AgNO3, we successfully manufactured LIG with a uniform dispersion of silver nanoparticles across its surface. The experimental results for the flexible strain sensor exhibit exceptional characteristics, including low resistance (183.4 Ω), high sensitivity (426.8), a response time of approximately 150 ms, and a relaxation time of about 200 ms. Moreover, this sensor demonstrates excellent stability under various tensile strains and remarkable repeatability during cyclic tests lasting up to 8,000 s. Additionally, this technique yields favorable results in finger bending and hand back stretching experiments, holding significant reference value for preserving the inherent characteristics of LIG preparation in a single-step and in situ manner.

Q-switched laser radiation at wavelengths of 355 nm, 532 nm, and 1064 nm from a Nd: YAG laser was used to generate plasma in laboratory air at the target surface made of compressed nano-silver particles of size 95 ± 10 nm. The emitted resonance spectra from the neutral silver at wavelengths of 327.9 nm and 338.2 nm indicate existence of self-reversal in addition to plasma self-absorption. Both lines were identified in emission spectra at different laser irradiation wavelengths with characteristic dips at the un-shifted central wavelengths. These dips are usually associated with self-reversal. Under similar conditions, plasmas at the corresponding bulk silver target were generated. The recorded emission spectra were compared to those obtained from the nano-material target. The comparisons confirm existence of self-reversal of resonance lines that emerge from plasmas produced at nano-material targets. This work suggests a method for recovery of the spectral line shapes and discusses practical examples. In addition, subsidiary calibration efforts that utilize the Balmer series Hα-line reveal that other Ag I lines at 827.35 nm and 768.7 nm are optically thin under variety of experimental conditions and are well-suited as reference lines for measurement of the laser plasma electron density.

Two new dimacrolide sesquiterpene pyridine alkaloids (DMSPAs), dimacroregelines A (1) and B (2), were isolated from the stems of Tripterygium regelii. The structures of both compounds were characterized by extensive 1D and 2D NMR spectroscopic analyses, as well as HRESIMS data. Compounds 1 and 2 are two rare DMSPAs possessing unique 2-(3′-carboxybutyl)-3-furanoic acid units forming the second macrocyclic ring, representing the first example of DMSPAs bearing an extra furan ring in their second macrocyclic ring system. Compound 2 showed inhibitory effects on the proliferation of human rheumatoid arthritis synovial fibroblast cell (MH7A) at a concentration of 20 μM.

Fused silica glass is a material with outstanding mechanical, thermal and optical properties. Being a brittle material, it is challenging to shape. In the last decade, the manufacturing of monolithic flexible mechanisms in fused silica has evolved with the femtosecond laser-assisted etching process. However, instrumenting those structures is demanding. To address this obstacle, this article proposes to inscribe a Bragg Grating sensor inside a flexure and interface it with an optical fibre to record the strain using a spectrum analyzer. The strain sensitivity of this Bragg Grating sensor is characterized at 1.2 pm/μϵ (1 μϵ = 1 microstrain). Among other applications, deformation sensing can be used to record a force. Its use as a micro-force sensor is estimated. The sensor resolution is limited by our recording equipment to 30 μN over a measurement range above 10 mN. This technology can offer opportunities for surgery applications or others where precision and stability in harsh environments are required.

In this paper glass crystallization behavior of 50ZnO:47B2O3:3Nb2O3:0.5Eu2O3 (G-0h) glass has been investigated in detail by DSC, XRD and TEM analysis. The luminescent properties of resulted glass-ceramics were also investigated. By XRD and TEM analysis crystallization of several crystalline phases have been proved (α-Zn3B2O6, β-Zn3B2O6 and ZnNb2O6). By calculating of crystal parameters it was found that europium ions are successfully incorporated in the β-Zn3B2O6. Photo-luminescent spectra show an increased emission in the resulting glass-ceramic samples as compared with the parent glass sample because of the higher asymmetry of Eu3+ ions in the crystalline phases obtained. It was established that the optimum emission intensity is registered for glass-ceramic sample obtained after 25 hours heat treatment of the parent glass.

Laser marking on polymer composite surfaces can be difficult to contrast and cause readability problems for electronic decoding equipment on production lines due to poor interaction between the laser and the fibres used to reinforce these materials. This problem can be solved with the right choice of marking parameters, resulting in savings for companies by avoiding production problems such as rejection, scrap and customer complaints. The present work uses the PBT/glass fibre composite used in the manufacture of instrument panels for motorcycles. The tests were carried out with different laser marking parameters using a Nd: YAG laser. Subsequently, the laser-marked DMC codes were analysed using a Verifier to evaluate the quality according to the ISO/IEC 29158:2020 standard. A detailed analysis of these surfaces was also carried out to observe some physical and chemical changes using SEM microscopy and EDS spectroscopy. The optical analysis showed that the lower the radiation power and pulse frequency and the higher the marking speed, the weaker the laser marking and therefore the poorer the DMC code quality, which was confirmed by the SEM. EDS spectroscopy showed that the laser marking process did not affect the chemical changes on the sample surface.

Laser Direct Writing (LDW), also known as 3D multi-photon laser lithography of resins, is a promising technique for fabricating complex free-form elements, including micro-optical functional components. Regular organic or hybrid (organic-inorganic) resins are often used, with latter exhibiting better optical characteristics, as well as having the option to be heat-treated into inorganic glass-like structures, particularly useful for resilient micro-optics. While this work is a continuation of SZ2080™ calcination development , the Laser-Induced Damage Threshold (LIDT) of such sol-gel-derived glass micro-structures, particularly those that undergo heat treatment, has not been well-characterized. In this pilot study, we investigated the LIDT using the Series-on-One (S-on-1) protocol of functional micro-lenses produced via LDW and subsequently calcinated. Our results demonstrate that the LIDT can be significantly increased, even multiple times, by this approach, thus enhancing the resilience and usefulness of these free-form micro-optics. This work represents the first investigation in terms of LIDT into the impact of calcination on LDW produced sol-gel-derived glass micro-structures, and provides important insights for the development of robust micro-optical devices.

: The crystallization conditions from the solution play an important role in determining the mor-phology, phase composition, and photovoltaic properties of perovskite films. Post-processing of the obtained films can have a crucial role in increasing the grain size of perovskite and enhancing its crystallinity. It has been shown that the formation of crystal nuclei can be utilized to accelerate crystallization. In this case, crystallization occurs through the growth of seed crystals created in the solution, enabling the formation of relatively large crystals. For the deposition of CH3NH3PbI3 hybrid halide perovskite films from a solution of the perovskite in dimethylformamide the spin coating technique was employed. Pre-crystallization was achieved by annealing the films at a temperature of 100 or 110 °C. The dissolution process involved adding a drop of dimethylformamide onto the substrate surface and allowing it to partially dissolve the perovskite film. Subsequently, residual solvent was removed through spin coating. The mor-phological analysis of the perovskite film surface after recrystallization at temperatures ranging from 80 to 130 °C was performed. The infrared transmission spectra of the obtained perovskite films were investigated, and their light absorption characteristics were studied through transmission spectra. The perovskite structure in the obtained films was confirmed by the peaks observed in the X-ray diffraction patterns.

We present results on the spontaneous crystallization of freely-jointed polymers of hard spheres obtained in an unprecedentedly long Monte Carlo (MC) simulation on a system of 54 chains of 1000 monomers. Starting from a purely amorphous configuration and after a transitory dominance of the hexagonal closed packed (HCP) polymorph, the system crystallizes in a final, stable, face centered cubic (FCC) crystal of very high perfection. Through refined metrics we gauge the degree of ordering and identify the regions of the phase transition and the corresponding morphologies. An analysis of chain conformational characteristics, of the spatial distribution of monomers and of the volume accessible to them shows that the phase transition is caused by an increase in translational entropy that is larger than the loss of conformational entropy of the chains in the crystal compared to the amorphous state. Polymer chains in the crystal adopt ideal random walk statistics as their great length renders local conformational details, imposed by the geometry of the FCC crystal, irrelevant.

Matrix metalloproteinases (MMPs) are often considered biomarkers of skin fibrosis. At the early stages of the pathological process, an elevation of their enzymatic activity causes significant changes in the composition of the extracellular matrix. MMPs secreted by immune cells facilitate their migration to the site of damage. Then, the immune cells eliminate the affected cells and biomolecules. Moreover, bidirectional changes in the activity of proteolytic enzymes, including MMPs, accompany wound healing. This study aimed to assess changes in the expression of Mmp2, Mmp3, and Mmp9 after treating the mice with laser therapy using the experimental model of bleomycin-induced skin fibrosis. Using immunohistochemistry, we characterized the histological features of scarred skin. We also analyzed changes in the expression of MMPs using real-time polymerase chain reaction before and after the irradiation with laser. We showed that treatment of the mice with CO2 laser partially normalized the histological features of scarred skin. We also noticed a decrease in the expression of Mmp2, Mmp3 (both p < 0.05), and Mmp9 (p = 0.065) during scar healing. The obtained results suggest that normalization of skin homeostasis requires a control of MMPs activities via induction of their genes.

We report on the study of ultrafast laser-induced plasma expansion dynamics in a gas microjet. To this purpose, we focused femtosecond laser pulses on a nitrogen jet produced through a homemade De Laval micronozzle. The laser excitation leads to plasma excitation with a characteristic spectral line emission at 391 nm. By following the emitted signal with a detection system based on an Intensified Charge-Coupled Device (ICCD) we captured the two-dimensional spatial evolution of the photo-excited nitrogen ions with a temporal resolution on the nanosecond time scale. We fabricated the micronozzle on fused silica substrate by femtosecond laser micromachining. This technique enables high accuracy and three-dimensional capabilities, thus providing an ideal platform for developing glass-based microfluidic structures for application to plasma physics and ultrafast spectroscopy.

Nonlinear properties of zinc germanium diphosphide (ZGP) crystals enable their ap-plications in powerful mid-IR optical parametric oscillators and second-harmonic generators. This paper summarizes mechanisms of the laser induced damage (LID) in high-purity ZGP crystals under periodically pulsed nanosecond irradiation by a Ho3+:YAG laser at 2.1 μm. The ZGP samples were manufactured by “LOC” Ent., Tomsk, Russia, or Harbin Institute of Technology, China. The impact of processing techniques and the post-growing methods for polishing and anti-reflection coating on the LID threshold are discussed. The importance of the defect structure of the crystal lattice and the parameters of transparent coatings for increasing the LID threshold is discussed. The impact of the test laser parameters on the LID threshold is analyzed. The transient area near the LID threshold obtained using digital holography is ana-lyzed. Influence of the pre-damage processes on the optical parametric oscillations is reported. Prospects for improving ZGP crystals to further increase the LID threshold are discussed.

Reviewed are recent efforts leading to chemo-enzymatic syntheses of strongly fluorescent ribosides of nucleobase analogs, potentially applicable in analytical biochemistry and cell biology. Described are syntheses and properties of fluorescent purine, 8-azapurine and etheno-purine ribosides, obtained using various types of the purine nucleoside phosphorylase (PNP) as catalysts of ribosylation, and -ribose-1-phosphate (r1P) as a second substrate. In several instances, the ribosylation sites were different than the canonical purine N9. Some of the obtained ribosides show fluorescence yields close to 100%. Their main applications are assays of PNP, nucleoside hydrolases, and other enzyme activities both in vitro and, possibly, within the living cells, using fluorescence microscopy.

In this article, we describe a simple procedure for evaluating the sterility of nutrient media using a shear-horizontal surface acoustic wave (SH-SAW) biosensor. We used the SH-SAW biosensor platform to monitor the time-dependent phase responses of the material for the media that binds to a monolayer of 3-mercaptopropanyl-N-hydroxy succinimide on the biosensor surface. Increases in the phase shift less than 50% of the starting phase shift recorded 180 minutes after the sterilization indicate a successful sterility test of the media. Our devices were then applied to sterility testing using a viable Escherichia coli (E. coli) K-12 solution to confirm our hypothesis. Filtered LB Broth was the negative control, and a 24-hour culture of E. coli was the positive control. Before testing, the cell solution was pelleted, the media decanted and then replaced with a 1x phosphate-buffered saline solution (1x PBS). Since we know that the N-hydroxysuccinimide residues will bind to amine groups, only in cases where microbial species are present will the surface binding increase greater than 50%. We confirmed our hypothesis using SH-SAW biosensors and overnight E. coli cultures. The sensitivity for our 250 MHz quartz SH-SAW sensors was calculated based on the response from the E. coli K-12 solution over the linear dynamic range, which appears to be 2x104 – 2x107 CFU per ml and has a sensitivity of S = 1.655x105 o m2 Kg-1. The limit of detection (LOD) for these sensors was calculated to be approximately 2x10-9 grams (g) which is estimated to be approximately 2,000 Escherichia coli (E. coli) K-12 cells. However, the sensitivity and insertion loss remained approximately unchanged before and after coating the sensor with 3,3'-Dithiobis(succinimidyl) Propionate (DSP).

A configurable design of a microstrip square spiral RFID tag antenna, for a wide range of microwave frequencies in S- and C-band, is presented. The design is parameterized in dimensions, and hence changing the design frequency (or frequencies) is easy, by changing only an initial value for the spiral geometry. A tag specimen was fabricated using Cu electroplating technique according to the design for frequencies of interest in the areas of 2.4 and 5.8 GHz. The substrate material is a 320 μm high resistivity Si and the bridge dielectric is a 15μm polyimide PI2525. The microfabrication process involves steps of metallic structure pattern transfer techniques with optical UV lithography procedures. The reflection coefficient and gain of the specimen were measured inside an anechoic enclosure using a vector network analyzer (VNA) and a TEM horn test antenna over a frequency range of up to 6 GHz. Simulated and measured results are presented and discussed, exhibiting reasonable agreement.

As modern systems are becoming more complex their control strategy cannot longer relay only on measurement information that usually comes from probes but also from mathematical models. Those systems models can lead to unbearable computation times due to their own complexity, turning the control process non-viable, which leads to the implementation of surrogate models that enable to achieve estimates within acceptable time to take decisions. A control trained with Deep Reinforcement Learning algorithm, using a Physics-Informed Neural Network to obtain the temperature map on the following time step, replaces the need of running Direct Numerical Simulations. On this work we considered an 1D heat conduction problem, which temperature distribution feeds a control system to activate a heat source aiming to obtain a constant, previously defined, temperature value. With this approach, control training becomes much faster without the need of performing numerical simulations or laboratory measurements, as well the control is taken based on Neural Network enabling its implementation on simple processors to edge computing.

Epithelial ovarian cancer (EOC) has not significantly benefited from advances in immunotherapy, mainly because of the lack of well-defined actionable antigen targets. Using proteogenomic analyses of primary EOC tumors, we previously identified 91 aberrantly expressed tumor-specific antigens (TSAs) originating from unmutated genomic sequences. Most of these TSAs derive from non-exonic regions, and their expression results from cancer-specific epigenetic changes. The present study aimed to evaluate the immunogenicity of 48 TSAs selected according to two criteria: presentation by highly prevalent HLA allotypes and expression in a significant fraction of EOC tumors. Using targeted mass spectrometry analyses, we found that pulsing with synthetic TSA peptides leads to a high-level presentation on dendritic cells. TSA abundance correlated with the predicted binding affinity to the HLA allotype. We stimulated naïve CD8 T cells from healthy blood donors with TSA-pulsed dendritic cells and assessed their expansion with two assays: MHC-peptide tetramer staining and TCR Vβ CDR3 sequencing. We report that these TSAs can expand sizeable populations of CD8 T cells and, therefore, represent attractive targets for EOC immunotherapy.

Knee osteoarthritis (KO) is an important health condition, affecting one third of the people aged 65 years or more. Pain is the main cause of disability. Pain management in KO includes pharmacological and non-pharmacological modalities. Patient education, lifestyle changes, physical exercise and physical agents are prescribed as a first approach for pain control. Laser therapy is part of many therapeutical protocols, with two forms, low-level laser therapy (LLLT) and high-intensity laser therapy (HILT). The paper aimed at stressing the advantages of HILT, based on a greater wavelength, higher energy delivery and deeper tissue penetration. Research on 23 published trials revealed that analgesic effect is rapid, cumulative and long lasting. Compared to sham, to LLLT or to other associations of therapeutical modalities, HILT provided significantly better results on pain reduction and functional improvement. Ultrasound examination showed reduction of intraarticular inflammation.

This work communicates the connection of measured shadowgraphs from optically induced air breakdown with emission spectroscopy in selected gas mixtures. Laser-induced optical breakdown is generated using 850 mJ and 170 mJ, 6-ns pulses at a wavelength of 1064 nm, the shadowgraphs are recorded using time-delayed 5-ns pulses at a wavelength of 532 nm and a digital camera, and emission spectra are recorded for typically a dozen of discrete time-delays from optical breakdown by employing an intensified charge-coupled device. The symmetry of the breakdown event can be viewed as close-to spherical symmetry for time-delays of several 100 ns. Spectroscopic analysis explores well-above hypersonic expansion dynamics using primarily the diatomic molecule cyanide and atomic hydrogen emission spectroscopy. Analysis of the air breakdown and selected gas breakdown events permits the use of Abel inversion for inference of the expanding species distribution. Typically, species are prevalent at higher density near the hypersonically expanding shockwave, measured by tracing cyanide and a specific carbon atomic line. Overall, recorded air breakdown shadowgraphs are indicative of laser-plasma expansion in selected gas mixtures, and optical spectroscopy delivers analytical insight into plasma expansion phenomena.

Water footprint has been widely used to illustrate the consumption of water in many situations; for instance, in products, processes or regions of interest. In this work, we analyzed – using a sensitivity analysis approach – the effect of some variables in the calculation of the water footprint in the viticulture in Brazilian Serra Gaúcha (the major producing region of Brazilian Wine).The classical Penman-Monteith model for evapotransporation was considered, with uncertainties in some parameters (dead mulch covering fraction in the vineyard, maximum temperatures for some months, altitudes and latitudes of the site). The sensitivity analysis was conducted using the SAFE toolbox under Octave framework. The results indicated that the the portion of the water footprint corresponding to the evapotranspiration is more sensitive to the values of mulch covering fraction and the altitude of the site in comparison with the latitude and the maximum temperatures.

Polymeric Intraocular lenses (IOLs) are vital for restoring vision following cataract surgery and for correcting refractive errors. Despite technological and medical advancements, challenges persist in achieving optimal vision and preventing complications. Surface modifications aim to mitigate the risk of posterior capsule opacification (PCO), while pre-operative measurements aid in selecting suitable IOLs. However, individualized solutions are lacking and there is a clear demand for the development of fully customised IOL surfaces. We employ laser micromachining technology for precise modifications via ablation on PMMA and Acrylic IOLs, using femtosecond (fs), nanosecond (ns), and diode continuous wave (CW) lasers, at wavelengths ranging from near-ultraviolet to infrared. Characterization reveals controlled ablation patterning, achieving feature sizes from as small as 400 nm to several micrometers. Regular and confocal Micro-Raman spectroscopy revealed alterations of the IOL materials' structural integrity for some pattering cases, thus affecting the optical properties, while these can be minimised by proper selection of micromachining conditions. The results suggest the feasibility of accurate IOL patterning, which could offer personalized vision correction solutions, based on relevant corneal wavefront data, thus surpassing standard lenses, marking a significant advancement in cataract surgery outcomes.

Ensembles of Species Distribution Models (SDMs) represent the geographic ranges of pathogen vectors by combining alternative analytical approaches and merging information on vector occurrences with more extensive environmental data. Biased collection data impact SDMs, regardless of the target species but no studies have compared the differences in the distributions predicted by the ensemble models when different sampling frameworks are used for the same species. We compared Ensemble SDMs for two important Ixodid tick vectors, Amblyomma americanum and Ixodes scapularis in mainland Florida, USA, when inputs were either convenience samples of ticks, or collections obtained using the standard protocols promulgated by the U.S. Centers for Disease Control and Prevention. The Ensemble SDMs for the convenience samples and standard surveys showed only a slight agreement (Kappa = 0.060, A. americanum; 0.053, I. scapularis). Convenience sample SDMs indicated A. americanum and I. scapularis should be absent from 34.5% and 30.9% of the state where standard surveys predicted the highest likelihood of occurrence of the respective vectors. Ensemble models from standard surveys predicted 81.4% and 72.5% (A. americanum and I. scapularis) of convenience sample sites. Omission errors by standard survey SDMs, of the convenience collections, frequently were associated with adjacency to at least one SDM or errors in geocoding algorithms that failed to correctly locate convenience samples. These geocoding errors emphasize commonly overlooked needs to explicitly evaluate and improve data quality for vector survey data used in spatial models.

In this study we have investigated the effect of the addition of Nb2O5 (up to 5 mol%) on the structure and luminescent properties of ZnO-B2O3 glass doped with 0.5 mol % Eu2O3 by using of infrared (IR), Raman and photoluminescence (PL) spectroscopy. Physical properties as molar volume, oxygen packing density and glass transition temperature were determined using the results of differential thermal analyisis (DTA) and Archimedes principle for density. IR and Raman spectra revealed that niobium ions incorporate into the base zinc borate glass as NbO4 trtraherda and NbO6 octahedra. A strong red emission from the 5D0 level of Eu3+ ions was registered under near UV (392 nm) excitation using the sharp 7F0 - 5L6 transition of Eu3+. The integrated fluorescence intensity ratio R (5D0 → 7F2/5D0 → 7F1) was calculated to estimate the degree of asymmetry around the active ion, suggesting a location of Eu3+ in non-centrosymmetric sites. The higher Еu3+ luminescence emission observed in zinc borate glasses containing 1÷5 mol% Nb2O5 compared to the Nb2O5-free zinc borate glass evidences that Nb2O5 is suitable component for modification of host glass structure and improving the emission intensity.

Based on the need for real-time sag monitoring of Overhead Power Lines (OPL) for electricity transmission, this article presents the implementation of a hardware and software system for online monitoring of OPL cables and cable sag determination. The mathematical model based on differential equations and the methods of algorithmic calculation of OPL cable sag are presented. Considering that, based on the mathematical model presented, the calculation of OPL cable sag can be done in different ways depending on the sensors used, and the presented application uses a variety of sensors. Therefore, a direct calculation is made using one of the different methods. Subsequently, the verification relations are highlighted directly and, respectively, the calculation by the alternative method, which uses another group of sensors, to generate both a verification of the calculation and the functionality of the sensors, thus obtaining a defect observer of the sensors. The hardware architecture of the OPL cable online monitoring application is presented, together with the main characteristics of the sensors and communication equipment used. The configurations required to transmit data using the ModBUS and ZigBee protocols are also presented. The main software modules of the OPL cable condition monitoring application are described, which ensure the monitoring of the main parameters of the power line and the visualisation of the results both on the electricity provider's intranet using a web server and MySQL database, and on the Internet using an Internet of Things (IoT) server. This categorisation of the data visualisation mode is done in such a way as to ensure a high level of cyber security. Starting from the mathematical model of the OPL cable sag calculation, it goes through the stages of creating such a monitoring system, from the numerical simulations carried out using Matlab to the real-time implementation of this monitoring application. The main modules of the application software are: the software module for reading quantities from the sensor network through a ModBUS Input/Output (I/O) server, the software module for real-time calculation of the OPL cable sag, the software module for read/write operations based on MySQL type data, the software module for transferring data to the user's intranet through a web server, and the software module for viewing data by authorised users based on user and password through an IoT server. The development software environments used are Matlab and Laboratory Virtual Instrument Engineering Workbench (LabVIEW).

We report interfacial crystallization in droplets of saline solutions placed on superhydrophobic surfaces and liquid marbles filled with the saline. Evaporation of saline droplets deposited on superhydrophobic surface resulted in the formation of cup-shaped millimeter-scaled residues. The formation of the cup-like deposit is reasonably explained within the framework of the theory of the coffee-stain effect, namely, the rate of heterogeneous crystallization along the contact line of the droplet is many times higher than in the droplet bulk. Crystallization within evaporated saline marbles, coated with lycopodium particles, depends strongly on the evaporation rate. Rapidly evaporated saline marbles yielded dented shells built of a mixture of colloidal particles and NaCl crystals. We relate the formation of these shells to the interfacial crystallization promoted by hydrophobic particles coating the marbles, accompanied with the upward convection flows supplying the saline to the particles, serving as the centers of interfacial crystallization. Convective flows prevail over the diffusion mass transport for the saline marbles heated from below.

White spot lesions (WSLs), a side effect of orthodontic treatment, can result in reversible and unaesthetic results. Graphene oxide (GO) with a bioactive glass (BAG) mixture(BAG@GO) was added to Low Viscosity Transbond XT(LV) in a ratio of 1, 3, 5%. The composite’s characterization and its physical and biological properties were verified with scanning electron microscopy(SEM) and X-ray diffraction(XRD); its microhardness, shear bond stress (SBS), cell viability, and adhesive remnant index (ARI) were also assessed. Efficiency in reducing WSL was evaluated using antibacterial activity of S. mutans. Anti-demineralization was analyzed using a cycle of the acid-base solution. Adhesives with 3 or 5 wt.% of BAG@GO showed significant increase in microhardness compared with LV. The sample and LV groups showed no significant differences in SBS or ARI. The cell viability test confirmed that none of the sample groups showed higher toxicity compared to the LV group. Antibacterial activity was higher in the 48-hour group than in the 24-hour group; the 48-hour test showed that BAG@GO had a high antibacterial effect, which was more pronounced in 5 wt.% of BAG@GO. Anti-demineralization effect was higher in the BAG@GO-group than in the LV-group; the higher the BAG@GO concentration, the higher the anti-demineralization effect.

The Vogel-Fulcher-Tammann equation is exposed as a particular example of the mean field theory. It is generalized by taking into account an arbitrary critical exponent of susceptibility, discriminating between different classes of universality. The Bell-Evans-Polanyi principle is employed to estimate the difference between the activation energies of flows in crystals and glasses, which appears to coincide with the excess Gibbs energy of the glass compared to the crystal.

This paper investigates the effect of Fe contamination on the microstructure and mechanical properties of Al-7Si-0.7Mg-Fe2.5 alloy processed by Laser Powder Bed Fusion (LPBF) and heat treated in two different conditions: (1) Solution Heat Treatment (SHT) at 520 °C, followed by artificial ageing at 160 °C (T6), and (2) Direct Artificial Ageing of the as-printed material at 160 °C (DAA). Microstructural characterization was carried out by Optical Microscopy (OM), X-Ray Diffraction (XRD), Scanning Electron Microscopy (SEM), and Transmission Electron Microscope (TEM). Mechanical characterization was carried out by tensile tests at room temperature. The formation of fine AlSiFe phases such as α-AlFeSi, β-AlFeSi, and π-Al8Si6Mg3Fe had no deleterious effect on the mechanical properties compared to previous studies for AlSIMg alloys without Fe. However, compared to the as-printed condition, the T6 heat treatment decreased the ultimate tensile strain significantly, while the elongation to the fracture presented a slight improvement.

Probiotic feed additives have attracted considerable research interest in recent years because the effectiveness of probiotics can differ across microbial strains and the supplemented macroorganisms. The present study was conducted on 16 lambs divided into two groups (C - control and E - experimental). The examined lambs were aged 11 days at the beginning of the experiment and 40 days at the end of the experiment. The diet of group E lambs was supplemented with a multi-strain probiotic formulation (Lactobacillus plantarum AMT14, Lactobacillus plantarum AMT4, Lactobacillus rhamnosus AMT15, and Bifidobacterium animalis AMT30), whereas group C lambs did not receive the probiotic additive. At the beginning of the experiment (day 0) and on experimental days 15 and 30, blood was sampled from the jugular vein to determine and compare: phagocytic activity (PHAGOTEST) and oxidative metabolism (PHAGOBURST) of peripheral blood granulocytes and monocytes by flow cytometry. An analysis of the phagocytic activity of granulocytes and monocytes revealed significantly higher levels of phagocytic activity (expressed as the percentage of phagocytic cells and mean fluorescence intensity) in lambs administered the multi-strain probiotic formulation than in the control group. The probiotic feed additive also exerted a positive effect on the oxidative metabolism of both granulocytes and monocytes (expressed as the percentage of oxidative metabolism and mean fluorescence intensity) after stimulation with Escherichia coli bacteria and with PMA (4-phorbol-12-β-myristate-13-acetate).

This paper develops the study of the effect of powerful ultrasound on the laser breakdown of liquids and a comparative study of the possibilities of acoustic and optical diagnostics of breakdown. The method of laser-induced breakdown spectroscopy (LIBS) for elemental analysis of liquids, along with high efficiency, continues to be less sensitive compared to traditional chemical methods. The paper develops a method of using additional ultrasound irradiation of the laser breakdown area in order to increase the efficiency of LIBS. Using the developed technique, spectral lines of chemical elements such as potassium, manganese, sodium, calcium, etc. were obtained for the first time depending on the frequency and power of ultrasound. It is shown that a sharp increase in the intensity of spectral lines of elements in water during laser breakdown is observed in the field of high-power ultrasound. It indicates an increase in the sensitivity of the combined method of ultrasonic LIBS. Along with the optical spectrum, the spectral and energy characteristics of acoustic emission were studied. An automated complex for hydrophysical and spectral studies is described, which was tested in the Sea of Japan during the voyage No. 81 of the research vessel RV "Professor Gagarinsky" in August 2022.

Multidrug resistant organisms (MDROs) outbreaks have been steadilyincreasing in Intensive care units (ICUs). Still, healthcare institutions and workers (HCW) reached no unanimity on how and when implementing infection prevention and control (IPC) strategies. We aimed to provide a pragmatic, physician practice-oriented, resume of strategies towards different MRDOs outbreaks in ICU. We performed a narrative review on IPC in ICUs, investigating patient-to-staff ratios, education, isolation, decolonization, screening and hygiene practices, outbreak reporting, cost-effectiveness, reproduction-number(R0), and future perspectives. The most effective IPC strategy remains unknown. Most studies focus on a specific pathogen or disease, making the clinician losing the big picture. IPC strategies proved their cost-effectiveness regardless typology, country, or pathogen. A standardized, universal, pragmatic protocol for HCW education should be elaborated. Likewise, a rapid outbreak recognition tool elaboration (i.e., an easy-to-use mathematical model) would improve early diagnosis and spreading prevention. Further studies are needed to express in favor or against MDROs decolonization. New promising strategies are emerging and need to be tested in the field. The lack of IPC strategies application has made, and still makes ICUs a major MDROs reservoir into the community. In a not-too-distant future genetic engineering and phage therapies could represent a plot-twist in MDROs IPC strategies.

Despite the recognized influence of body mass on combat techniques, the relationship between body segment mass (BSM) and combat moves remains unexplored. This study aimed to examine the relationship between striking arm mass (SAM), kicking leg mass (KLM), and body mass (BM) with the dynamic forces of the direct punches (DP), palm strikes (PS), elbow strikes (ES), front kicks (FK), and countermovement jumps (CMJ) performance. Sixteen male military cadets (22.3 ± 1.8 years, 181.4 ± 7.0 cm, 82.1 ± 8.5 kg) performed combat techniques, with performance measured by using a force plate and body segment mass assessed by Dual-energy X-ray absorptiometry. Spearman's correlation analysis, the Wilcoxon test, and Cohen's d were applied. Results indicated the relationship between KLM or BM and FK impulse (r = 0.64, p = 0.01; r = 0.52, p = 0.04, respectively) and CMJ impact force (r = 0.80, p ≤ 0.01; r = 0.70, p ≤ 0.01, respectively). Moreover, FK peak and impact forces were moderately correlated with CMJ jump height (r = 0.74, p ≤ 0.01; r = 0.77, p ≤ 0.01). The highest relationship was found between KLM and FK impulse; however, the difference in variability explained by KLM versus body mass is only 12%. This suggests that knowledge of BSM did not provide a significantly better estimate of the dynamic forces of the punches and FK than BM.

This work aimed to synthesize new N-rich triazole compounds. In this article we describe the synthesis of three different 1,2,4-triazole-based systems starting from 1,3-diaminoguanidine hydrochloride monohydrate. The structure of the obtained crystals was established by single-crystal X-Ray diffraction. The high nitrogen content of the synthetized compounds makes them building blocks for the application in the High-Energy-Density material science.

In recent years, the prevalence of tobacco and electronic cigarette (e-cigarette) use among adolescents has raised significant public health concerns worldwide. This study aims to investigate respiratory symptoms among Polish adolescents. We conducted an online survey among Polish school students from all provinces, collecting data over two months in Spring 2021. Students voluntarily complete the anonymous survey, answering questions about respiratory symptoms, smoking habits (both traditional and electronic cigarettes), and demographic information. Analysis focused on four subgroups: non-tobacco users, traditional cigarette smokers, e-cigarette users, and dual users, totaling 10,388 pupils aged 12-18 years, predominantly attending secondary technical and comprehensive schools. A total of 10388 pupils participated in the study, 55.6 % (5778) of whom were girls and 44.4 % (4610) boys. Adolescents, who admitted using both e-cigarettes and traditional cigarettes experienced more frequent episodes of cough during the day (39.70%) and at night (18.40%) compared to their peers in other groups. Chest discomfort, including pain and pressure, was also reported more often by adolescents, who used e-cigarettes and traditional cigarettes concurrently (27.60%) compared to their peers in other groups. Chest pressure was experienced less commonly by non-smoking adolescents (14.40%) than by smokers (18.90%). Higher severity of cough during the day and at night was observed in the group of adolescents using traditional cigarettes and e-cigarettes concurrently compared to the other groups. The adolescents in the dual user group experienced more severe dyspnoea and wheezing compared to the other groups included in the comparison. The results of this study confirm the correlation between the occurrence of respiratory symptoms in adolescents who smoke cigarettes, use e-cigarettes and in dual users. The respiratory symptoms occur most frequently and are the most severe in the group of adolescents who use e-cigarettes and traditional cigarettes

In Brazil, Brazilian borreliosis (BB), characterized molecularly, exhibits symptoms akin to Lyme disease (LD) but presents unique epidemiological, clinical, and morphological features. This study explores the incidence, diagnostic challenges, and awareness initiatives regarding this disease in Brazil. Employing a narrative review methodology, data were sourced from Pubmed, Ebsco, Google Scholar, and Web of Science without temporal constraints. Results reveal diagnostic complexities in Brazil due to the low sensitivity of conventional tests and the use of North American B. burgdorferi antigens. Despite challenges, epidemiological studies indicate an upswing in cases in humans and animals. Therefore, there is an urgent need to define new biomarkers, molecular strategies, or new antigenic targets to advance the development of vaccines and diagnostics. Early and accurate pathogen identification is crucial for active surveillance to comprehend and manage this zoonosis.

Laser-induced functionalisation using excimer laser irradiation has been widely applied to transparent conductive oxide films. However, exploring suitable irradiation conditions is time-consuming and cost-ineffective as there are numerous routine film fabrication and analytical processes. Thus, we herein explored a real-time technique to monitor the laser-induced functionalisation of transparent conductive oxide films. We developed two types of monitoring apparatus, electrical and optical, and applied them to magnetron-sputtered Sn-doped In2O3 films grown on glass substrates and hydrogen-doped In2O3 films on glass or plastic substrates using a picosecond Nd:YAG pulsed laser. Both techniques could monitor the functionalisation from a change in properties of the films on glass substrates by laser irradiation, but electrical measurement was unsuitable for plastic samples because of a laser-induced degradation of the underlying plastic substrate, which harmed proper electrical contact. Instead, we demonstrated that the optical properties in the near-infrared region were suitable for the monitoring and the changes in the optical properties were visually detected in real-time by using a near-infrared camera.

Controlled deposition of CoCrFeNiMo0.2 high entropy alloy (HEA) micro-particles was achieved using laser induced forward transfer (LIFT). Ultra-short laser pulses, 230 fs of 515 nm wavelength, were tightly focused into ∼ 2.4 μm focal spots on the ∼50 nm thick plasma-sputtered films of CoCrFeNiMo0.2. The HTA films were transferred onto glass substrates by magnetron sputtering in vacuum (10−8 atm) from the thermal spray coated substrates. The absorption coefficient of CoCrFeNiMo0.2 α ≈ 6 × 105 cm−1 was determined at 600 nm wavelength. The real and imaginary parts of refractive index (n + iκ) of HEA were determined from reflectance and transmittance using nano-films.

Members of the genus Armillaria are widespread forest pathogens against which effective protection has not yet been developed. Due to their longevity and the creation of large-scale cloning of Armillaria individuals, the use of mycoviruses as biocontrol agents (BCAs) against these pathogens could be an effective alternative. This work describes the screening of double-stranded RNA banding patterns as a first approach for potential virus discovery and the use of stranded total RNA-seq for viral detection and characterization in Armillaria spp. collected in the Czech Republic. A total of five single-stranded RNA viruses were detected in Armillaria ostoyae and A. cepistipes, including the first virus of the family Tymoviridae found infecting a member the genus Armillaria and four viruses belonging to the recently described virus group "ambiviruses" with circular ambisense genome organization. Both hammerhead (HHRz) and hairpin (HpRz) ribozymes were detected in all the ambiviricot sequences. Armillaria viruses were compared by phylogenetic analysis and confirmed their specific host by direct RT-PCR, which showed the occurrence of interspecies transmission.

A portable laser photoacoustic sensor based on a Field-Programmable Gate Array (FPGA) is reported for methane detection. A tunable DFB diode laser in the 1654 nm wavelength range is used as an excitation source. The photoacoustic signal processing was implemented by a FPGA device. A small resonant photoacoustic cell is designed. The minimum detection limit (1σ) of 10 ppm for methane (CH₄) is demonstrated.

Several Lung diseases can result in lung damage structural changes, with lung transplantation as a only therapeutic option when the disease reaches an advanced progression, unfortunately, the success of lung transplantation is limited. In this context, lung bioengineering is considered a potential therapeutic alternative and the current approach is based on the use of the natural extracellular matrix (ECM) of the decellularized lung. The use of undifferentiated cells to seed an ECM can be a more practical strategy for lung bioengineering but the sterilization of the organ for this recellularization process is still a challenge. In this sense, Low-Level Laser Therapy (LLLT) can emerge as a potential treatment alternative. Therefore, the objective of this study was to verify if LLLT, can optimize lung recelularization with mesenchymal stem cells by cytokine modulation. For this, we decellularized lungs from C57BL/6 mice perfusing SDS 1% via pulmonary artery, sterilized with LLL (660nm, 100mW, 30s). Whole lung scaffolds were recellularized: (1) Recellularized Lung (2) Recellularized Lung + LLLT. Mesenchymal stem cells derived from human tooth pulp (DPSc) were seeded into lungs and incubated for 24 hours at 37ºC, 5% CO₂, in a bioreactor-like conditions, maintaining CPAP at 20cmH2O, 90% O2, and LLL at wavelength of 808nm, 100mW, 30s. Culture medium were analyzed at 24 hours. H&E, immunostaining, SEM and ELISA assay were performed. We produced viable biological scaffolds absent of DNA content, preserving glycosaminoglycans and collagen I, III and IV, fibronectin, laminin and elastin and lung structure (SEM). The levels of IL-6 and IL-8 were stable during the 24 hours of culture. IFN-γ levels showed significant difference in the DPSc and DPSc+LLLT group in the 24-hour evaluation. The levels of IL-10 decreased after LLLT. These findings highlight LLLT's role in cytokine regulation and contamination prevention during lung recellularization with mesenchymal stem cells. Overall, these results demonstrated that LLLT's modulated cytokine levels and could prevent contamination during the lung recellularization process with mesenchymal stem cells, offering promise for enhanced therapeutic strategies in lung bioengineering.

To investigate the associated mechanisms concerning collagen and the expression of apoptosis-related proteins in porcine skin injuries induced by laser exposure, pig skin was treated with a 1064 nm laser. The healing process of the laser-treated areas, alterations in collagen structure, and changes in apoptosis were continuously observed and analyzed from 6 hours to 28 days post-irradiation. On the 28th day following exposure, wound contraction and recovery were notably sluggish in the medium-high dose groups, displaying more premature and delicate type III collagen within the newly regenerated tissues. The collagen density in these groups was roughly 37-58% of that in the normal group. Between days 14 and 28 after irradiation, there was a substantial rise in apoptotic cell count in the forming epidermis and granulation tissue of the medium-high dose group, in contrast to the normal group. Notably, the expression of proapoptotic proteins bax, caspase-3, and caspase-9 surged significantly 14 days after irradiation in the medium-high dose groups and persisted at elevated levels on the 28th day. During the later stage of wound healing, the augmented apoptotic cell population and insufficient collagen generation in the newborn skin tissue of the medium-high dose groups were closely associated with delayed wound recovery.

The exceptional performance of graphene has driven the advancement of its preparation technique and application. Laser-induced graphene (LIG), as a novel graphene preparation technique, has been applied in various fields. Graphene periodic structures created by LIG technique exhibit superhydrophobic characteristics and can be used for deicing and anti-icing applications, which are significantly influenced by the laser parameters. The laser surface treatment process was simulated by a finite element software analysis (COMSOL Multiphysics) to optimize the scanning parameter range, and the linear array surface structure were subsequently fabricated by the LIG technique. The generation of graphene was confirmed by Raman spectroscopy, and energy-dispersive X-ray spectroscopy. The periodic linear array structure were observed by Scanning electron microscopy (SEM) and confocal laser imaging (CLSM). In addition, CLSM testings, contact angle measurements, and delayed icing experiments were systematically performed to investigate the effect of scanning speed on surface hydrophobicity. The results show that the high quality and uniform graphene can be achieved using the laser scanning speed of 125 mm/s. The periodic linear array structures can obviously increase the contact angle and suppress delayed icing. Furthermore, these structures have the enhanced ability of the electric heating deicing, which can reach 100°C and 240°C within 15 s and within 60 s under the DC voltage power supply ranging from 3 to 7 V, respectively. These results indicate that the LIG technique can be developed to provide an efficient, economical, and convenient approach for preparing graphene and the hydrophobic surface array structure based on LIG has considerable potential for deicing and anti-icing applications.

The valley pseudospin properties of electrons in two–dimensional hexagonal materials result in lots of fascinating physical phenomena, which opens up the new field of valleytronics. The valley-contrasting physics aims at distinguishing the valley degree of freedom based on valley–dependent effects. Here, we theoretically demonstrate that both of the valley–selective high harmonic generation and valley–selective electronic excitation can be achieved by using an orthogonal two–color (OTC) laser field in gapped graphene. It is shown that the asymmetry degrees of harmonic yields in the plateaus, cutoff energies of generated harmonics and electron populations from two different valleys can be precisely controlled by the relative phase of the OTC laser field. Thus the selectivity of the dominant valley for the harmonic radiation and electronic polarization can be switched by adjusting the relative phase of the OTC laser field. Our work offers an all–optical route to produce the valley–resolved high harmonic emissions and manipulate the ultrafast valley polarization on a femtosecond timescale in condensed matter.

Populational aging is marked by chronic non-communicable diseases, such as metabolic syndrome (MetS). IL-10 and IL-1β are pleiotropic cytokines with multiple biological effects linked to metabolic disorders. This cross-sectional study assessed 193 participants' IL-10 and IL-1β serum levels regarding their role in developing MetS, clinical characteristics, and their IL1B rs1143627 and IL10 rs1800890 variants' genotype frequencies in a population over 60. IL-10 levels correlated weakly with HDL levels and fat mass and inversely with triglycerides, glucose, glycated hemoglobin, and estimated average blood glucose levels. IL-10 levels were also indirectly influenced by the patient's T2DM duration, lean mass amount, and bone mineral content. Participants with altered HDL, elevated serum glucose, raised HbA1c levels, or those over 80 had reduced serum IL-10 levels compared to those with normal levels or other age groups, respectively. Women also had higher serum IL-10 levels than men. Dissimilarity, IL-1β levels correlated directly only with the number of total leukocytes and segmented neutrophils, showing only significant variations with self-reported alcohol consumption. Our study also found that those with the IL10 AA genotype (lower IL-10 levels) had a significantly higher risk of developing MetS. These findings may help direct future research and more targeted therapeutic approaches in older adults.

Consumption of ultra-processed foods is associated with abdominal obesity, but this association has not yet been investigated in individuals on hemodialysis. This cross-sectional study, developed with 1014 individuals, aimed to analyze the prevalence of abdominal obesity and its association with the consumption of ultra-processed foods in individuals on hemodialysis. Consumption of ultra-processed foods was measured using a questionnaire, whose list of foods was based on the Surveillance System of Risk and Protective Factors for Chronic Non-Communicable Diseases through Telephone Enquiry. Waist circumference was used to determine the presence of abdominal obesity. The difference in proportions between the independent variables and the outcome was verified using Pearson's chi-square test. Hierarchical logistic regression was used to determine the association between the outcome and the independent variables. The prevalence of abdominal obesity was 77.22%. In the final model, higher consumption of ultra-processed foods, be male and an adult, have between 8 and 11 years of schooling and practice physical activity below the recommended level increased the chances of having abdominal obesity. The research provides a basis for the creation and improvement of public policies that promote improvements in these health determinants.

Among magnetoelectric (ME) heterostructures, ME laminates of the type Metglas-like / PVDF (magnetostrictive+piezoelectric constituents) have shown the highest induced ME voltages, usually detected at the magnetoelastic resonance of the magnetostrictive constituent. This ME coupling happens because of the high cross-correlation coupling between magnetostrictive and piezoelectric material, and is usually associated with a promising application scenario for sensors or actuators. In this work we detail the basis of the operation of such devices, as well as some arising questions (as size effects) concerning their best performance. Also, some examples of their use as very sensitive magnetic fields sensors or innovative energy harvesting devices will be presented At the end, the challenges, future perspectives and technical difficulties that will determine the success of ME composites for sensor applications are discussed.

Zirconium based bulk metallic glasses are industrially valuable materials which commercial market grows rapidly. Surface modification of these metallic glasses by high-intensity lasers is relatively new and costly treatment promising great advantages over classical surface processing methods. In this work we perform the case study of surface modification of Zr$_{46}$Cu$_{36.8}$Ag$_{9.2}$Al$_8$ metallic glass by high-intensity millisecond laser beam. Our results suggest chemical deposition of atmospheric oxygen and nitrogen in the laser-melted surface area and its surroundings. Zirconium nitride layer was detected in the middle of laser-irradiated area. Nanocrystals embedded in the amorphous matrix were also formed on the surface. Overall, our findings suggest possibilities for improvement of mechanical characteristics of the studied metallic glass.

Cancer treatment is a significant focus in medicine owing to the increasing global incidence. Patients with advanced cancers that do not respond to conventional therapies have limited options and an unfavorable prognosis. Consequently, researchers are investigating complementary approaches to conventional treatments. One such approach is alkalization therapy, which aims to neutralize the acidic tumor microenvironment (TME) by increasing its pH level. The acidic TME promotes inflammation, tumor progression, and drug resistance. Alkalization therapy has been demonstrated to be effective for various cancers. In addition, natural products, such as triterpenoids, parthenolides, fulvic acid, Taxus yunnanensis, and apple pectin have the potential to alleviate symptoms, maintain physical fitness, and improve treatment outcomes of cancer patients through their anti-inflammatory, antioxidant, and anticancer properties. In this review, we focus on the effects of alkalization therapy and natural products on cancer. Furthermore, we present a case series of advanced cancer patients who received alkalization therapy and natural products alongside standard treatments, resulting in long-term survival. We posit that alkalization therapy together with the supplementation of natural products may confer benefits to cancer patients by mitigating the side effects of chemotherapy and complementing standard treatments. However, further research is warranted to validate these clinical findings.

Diarrhea is a common occurrence following vascular organ transplantation, including kidney transplants. It can be induced by non-infectious factors, adverse effects of immunosuppressive drugs, or infectious agents such as viruses, bacteria, fungi, or parasites. Intestinal protozoan parasites, include Cryptosporidium spp., are causes of infectious diarrhea particularly in immunocompromised patients. This review aims to summarize reports on epidemiology, pathogenesis, clinical presentation, diagnosis, and treatment of Cryptosporidium spp. infection in adult patients, particularly following kidney transplantation.

Polymer inclusion membranes (PIMs), which contained cellulose tri-acetate used as a polymer base, a plasticizer in the form of o-NPOE, and meso-tetra methyl tetrakis-[methyl-2-(4-acetlphenoxy)] calix[4]pyrrole (KP) used as a carrier, were prepared and tested for the effective purification of aqueous solutions of methylene blue dye. The scanning electron microscope (SEM), thermogravimetric analysis (TGA), and attenuated total reflection Fourier transform infrared (ATR-FTIR) were used to define the microstructure and surface of PIMs. Experimental results showed that with the increased concentration of methylene blue in an aqueous solution, the removal percentage also increased. Further observation also showed that the flux increased with the rise of the source phase pH values from 3 to 10. The carrier and plasticizer content in the membrane significantly influenced the membrane’s transport properties. The optimal composition of the membrane in per cent by weight was for KP: 74% plasticizer; 18% support; 8% carrier. It was shown that the membrane with optimal composition showed good reusability and enabled the easy and spontaneous separation of methylene blue from aqueous solutions.

In this paper, we consider the temporal development of the optical density of the H$_\alpha$ spectral line in a hydrogen laser induced plasma. This is achieved by using the so-called duplication method in which the spectral line is re-imaged onto itself and the ratio of the spectral line with it duplication is taken to its measurement without the duplication. We asses the temporal development of the self-absorption of the H$_\alpha$ line by tracking the decay of duplication ratio from its ideal value of 2. We show that when 20% loss is considered along the duplication optical path length, the ratio is 1.8 and decays to a value of 1.25 indicating an optically thin plasma grows in optical density to an optical depth of 1.16 by 400 ns in the plasma decay for plasma initiation conditions using Nd:YAG laser radiation at 120 mJ per pulse in a 1.11$\times10^{5}$ Pa hydrogen/nitrogen gas mixture environment. We also go on to correct the H$_\alpha$ line profiles for the self-absorption impact using two methods. We show that a method in which the optical depth is directly calculated from the duplication ratio is equivalent to standard methods of self-absorption correction when only relative corrections to spectral emissions are needed.

Cybercrime Threat Intelligence (CTI) allows us to change our actions from reactive to proactive in the fight against threat actors, and to make more informed, data-driven security decisions. Thus this study proposes the practical implementation of CTI in the Arab world. This study focuses on strengthening CTI by integrating Indicators of Compromise (IoCs) and collecting realistic security alerts from honeypot systems and open source intelligence. The collected data is stored in the Malware Information Sharing Platform (MISP), an open source platform that allows users to create and share IoCs with other organizations while staying informed about new threats. It features an intuitive interface for data analysis and threat identification, facilitating sharing, storage, and correlation of IoCs. Therefore, we leveraged MISP to generate IoCs based on the collected data and analyzed the results to identify potential cyber threats. The implemented platform aims to provide organizations with actionable information to prevent, detect and respond to cybercrime. This study presents a practical approach to strengthening CTI in the Arab world and provides an opportunity to strengthen the region’s security posture.

IgE-mediated wheat allergy is a gluten-related disorder. Wheat is one of the five most common food allergens in children. However, the natural history of IgE-mediated wheat allergy has seldom been described in the research literature. This study presents the current state of knowledge about the IgE-mediated wheat allergy in children.

Direct femtosecond laser writing or inscription is a useful technique, and it has been 1 employed to engineer various materials in many applications including nonlinear photonic crystals, 2 which are of periodically patterned second-order nonlinearity to get and control the coherent light at 3 new frequencies. By manipulation of second-order nonlinearity, either erased or poled, quasi-phase 4 matching has been achieved in several crystals, especially three-dimensional nonlinear photonic 5 crystals have been originally proposed and proved to be truly three-dimensional. Here we shortly 6 review on the recent advances in the research field of nonlinear photonic crystals inscribed by 7 femtosecond laser. We also discuss some phenomena that not understood yet and the future possible research topics in this field.