Pipeline conflicts arising from data dependencies are a common issue encountered in the hardware implementation of layered QC-LDPC decoders. This paper proposes an efficient layered decoding architecture to reduce pipeline conflicts without introducing stall cycles, by reordering the processing order offline and using the patch method based on variable-to-check message. The experimental results on the LDPC code of the IEEE802.16 standard in the OFDM-PON system demonstrate that the proposed architecture has a sensitivity improvement of 0.125 dBm and 0.375 dBm, respectively, compared with our previous work and the method described in the other work.

By repeated unloading and loading of the excavation dynamic and static loads, repeated train dynamic and static loads of multi-factors, the underpass tunnel, cross tunnel engineering influence area rock layer, the existing tunnel structure of the three constitutes a multifaceted structure, multi-factor interaction system. Existing tunnels into the prediction theory model of the new tunnel excavation process of dynamic and static loads, dynamic and static loads of existing tunnels are mostly analyzed individually, the results of synergistic analysis needs to be improved. Based on the theory of the current layer method, the paper comprehensively considers the stiffness of the existing tunnel, the stiffness of the new tunnel, the excavation method load and the existing tunnel load, coupled with Peck's empirical formula, the theoretical model of deformation prediction for excavation of a two-lane highway tunnel under the tunnel through the existing railroad is proposed, and verified and optimized by numerical calculations and monitoring data, which proves the applicability and reliability of the theoretical model in the similar strata and the project promotion.

A time-sequential working, spatially multiplexed autostereoscopic 3D display design consisting of a fast switchable RGB-color filter array is presented. The wavelength-selective filter barrier emits the light from a display over a larger active area than common autostereoscopic barrier displays. An optical modelling of wavelength-selective barriers has been used for instance to calculate the light ray distribution properties of that arrangement. To find well working display designs, automated searches by simulation and computational evaluation has been proceeded. Wavelength-selective filter barrier arrangements exhibit characteristics different from common barrier displays with similar barrier pitch and ascent. In particular, these constructions show strong angular luminance dependency under barrier inclination specified by correspondent slant angle. In time-sequential implementation it is important to avoid that quick eye or eyelid movement lead to visible color artifacts. In the millisecond regime tunable liquid crystal Fabry-Pérot color filters for the colors red, green and blue are presented. They consist of a sub-micrometer thick nematic layer sandwiched between dielectric mirrors and ITO-electrodes. These cells shall switch narrow-banding light of red, green or blue. An array for a glasses-free 3D display has to be equipped with several thousand switchable filter elements having different color apertures. The newly introduced design is usable as a multi user display as well as a single user system with user adaptive control.

In this paper, we study the well-posedness and asymptotics of a one-dimensional thermoelastic laminated beam system either with or without structural damping, where the heat conduction is given by Fourier's law effective in the rotation angle displacements. We show that the system is well-posed by using Lumer-Philips theorem, and prove that the system is exponentially stable if and only if the wave speeds are equal, by using the perturbed energy method and Gearhart-Herbst-Prüss-Huang theorem. Furthermore, we show that the system with structural damping is polynomially stable provided that the wave speeds are not equal, by using the second-order energy method.

In this work, we consider a one-dimensional laminated beam in the case of non-equal wave speeds with only one infinite memory on the effective rotation angle. In this case, we establish the general decay result for the energy of solution without any kind of internal or boundary control. The main result is obtained by applying the method used in Guesmia et al. (Electron. J. Differential Equations 193: 1-45, 2012) and the second-order energy.

In this paper, we study the global existence and exponential decay for a dynamic contact problem between a Timoshenko beam with second sound and two rigid obstacles, of which the heat flux is given by Cattaneo's law instead of the usual Fourier's law. The main difficulties arise from the irregular boundary terms, from the low regularity of the weak solution and from the weaker dissipative effects of heat conduction induced by Cattaneo's law. By considering related penalized problems, proving some a priori estimates and passing to the limit, we prove the global existence of the solutions. By considering the approximate framework, constructing some new functionals and applying the perturbed energy method, we obtain the exponential decay result for the approximate solution, and then prove the exponential decay rate to the original problem by utilizing the weak lower semicontinuity arguments.

A printed Vivaldi antenna that is optically transparent, ultra-wideband (UWB), and reconfigurable has been developed, fabricated, and tested at millimeter wave frequencies. It covers a broad frequency range of 20-30 GHz by using three PIN diodes. The diodes control the current flow to direct the beam of the antenna. The results of numerical simulations and measurements match at millimeter wave frequencies. The design of this antenna is unique as it allows for a reduction in size and ease of integration while also providing the ability to change the radiation pattern by up to 300 degrees, making it suitable for 5G and 6G communications. Additionally, this antenna can also be useful for RF applications that require dynamic switching of radiation patterns and cognitive radio.

Layered superconductors are attractive because some of them show high critical temperatures. While their crystal structures are similar, those compounds are composed of many elements. Compounds with many elements tend to be incongruent melting compounds, thus, their single crystals cannot be grown via the melt-solidification process. Hence, these single crystals have to be grown below the decomposition temperature, and then the flux method, a very powerful tool for the growth of these single crystals with incongruent melting compounds, is used. This review shows the flux method for single-crystal growth technique by self-flux, chloride-based flux, and HPHT (high-pressure and high-temperature) flux method for many-layered superconductors: high-T_c cuprate, Fe-based and BiS₂-based compounds.

Neutral beam injection (NBI) is used for thermonuclear plasma heating, non-inductive current drive, rotation, operation scenario control, and for plasma diagnostics in nuclear fusion devices. NBI is the main source of fast particles in plasma which transmit energy to thermal plasma during their slow-down. Steady-state tokamak operation is only possible when the sub-thermal particles energy is absorbed and effectively confined in plasma volume. While NBI purposes and applications vary through different fusion systems, the engineering tasks performed during research and development (R&D) stage of neutral beamline design have much in common. The NBI studies, especially addressing long pulse and high-power operation typically include a beam transmission analysis and power loads distribution at the structural components of the beamline. Thermo-structural analysis is applied next to heat removal circuits design. ‘Beam Transmission’ (BTR) code is a dedicated tool, developed by a physicist and used by NBI physicists and engineers. BTR was created and 1^st applied during R&D phase of the world’s largest tokamak ITER. BTR code is intended for public usage and routinely applied for detailed simulations of neutral beam propagation through complex beamlines. BTR is flexible and intuitive in input, user-friendly and fully interactive. Thanks to visualization and high performance BTR looks and feels like a real NB flight simulator. Despite BTR ‘mature’ age, the code is still in evolution. Support is available to all new BTR users.

(1) Background: The significant progress observed over last two decades in coherent beam combining (CBC) technology has mainly focused on its applications in high-energy physics and laser weapons. This work provides insight into the basic principles of CBC and the search for an alternative, namely optical angular momentum (OAM) generation using CBC; (2) Methods: The semi-analytical model based on the paraxial wave equation explored generating OAM-CBC beams by manipulating the tilts and phases of CBC (T&P-CBC) of hexagonal architecture; (3) Results: The specially arranged T&P-CBC shows typical properties of OAM, such as annular profiles for the zero diffraction order and 1-st order replicas in the far field and correlation coefficients of 1% between different OAM-CBC fields; (4) Conclusions: The differences between classical OAM beams and OAM-CBC are substantial due to hexagonal lattice properties. Moreover, applications in free space optical communications are feasible as T&P CBC fulfills the main conditions and requirements for OAM generation.

We present a series of computer-assisted high resolution transmission electron (HRTEM) simulations to determine Moiré patters by induced twisting effects between slabs at rotational angles of 3°, 5°, 8°, and 16°, for molybdenum disulfide, graphene, tungsten disulfide, and tungsten selenide layered materials. In order to investigate the electronic structure, a series of numerical simulations using DFT methods was completed using CASTEP with a generalized gradient approximation to determine both band structure and density of states on honeycomb like new superlattices. Our results indicate metallic transitions when rotation approaches 8° with respect to each other for most of the two-dimensional systems that were analyzed.

The nucleation and dynamics of Josephson and Abrikosov vortices determine the critical currents of layered high-T_c superconducting (HTS) thin films, grain boundaries, and coated conductors, so understanding their mechanisms is of crucial importance. Here we treat pair creation of Josephson and Abrikosov vortices in layered superconductors as a secondary Josephson effect, in which each full vortex is viewed as a composite fluid of micro-vortices, such as pancake vortices, which tunnel coherently via a tunneling matrix element. We introduce a two-terminal magnetic (Weber) blockade effect that blocks tunneling below a threshold current, and simulate time-correlated vortex tunneling above threshold. The model shows nearly precise agreement with voltage-current (V-I) characteristics of HTS cuprate grain boundary junctions, which becomes more concave rounded as temperature decreases, and also explains the piecewise linear V-I behavior observed in iron-pnictide bicrystal junctions and other HTS devices. When applied to either Abrikosov or Josephson pair creation, the model explains a plateau seen in plots of critical current vs. thickness of HTS coated conductors. The observed correlation between theory and experiment strongly supports the proposed quantum picture of vortex nucleation and dynamics in layered superconductors.

The next generation network requires not only ultra high data rate, global coverage and connectivity, but also reducing network deployment costs and energy consumption. The emergence of reconfigurable intelligent surface (RIS) technology provides an effective way to improve efficiency and reduce cost, while the passive elements bring new challenges of channel estimation (CE) and beam tracking. For a RIS-aided multiple-input and single-output (MISO) system, in this paper, to achieve the channel state information (CSI), we propose a principle component analysis (PCA) based staged channel estimation method. Based on the estimated channel, we propose a deep learning (DL) based beam tracking scheme to realize low-complexity RIS reflection coefficient design, which effectively improves the signal-to-noise ratio (SNR) at the user side. Simulation results verify our proposed channel estimation scheme based on PCA and beam tracking scheme based on DNN for the semi-active RIS-aided MISO systems can obtain approximate performances with much lower computational complexity.

Over the past few years, we have experienced great technological advancements in the information and communication field, which has significantly contributed to reshaping the Intelligent Transportation System (ITS) concept. Evolving from the platform of a collection of sensors aiming to collect data, the data exchanged paradigm among vehicles is shifted from the local network to the cloud. With the introduction of cloud and edge computing along with ubiquitous 5G mobile network, it is expected to see the role of Artificial Intelligence (AI) in data processing and smart decision imminent. So as to fully understand the future automobile scenario in this verge of industrial revolution 4.0, it is necessary first of all to get a clear understanding of the cutting-edge technologies that going to take place in the automotive ecosystem so that the cyber-physical impact on transportation system can be measured. CIoV, which is abbreviated from Cognitive Internet of Vehicle, is one of the recently proposed architectures of the technological evolution in transportation, and it has amassed great attention. It introduces cloud-based artificial intelligence and machine learning into transportation system. What are the future expectations of CIoV? To fully contemplate this architecture’s future potentials, and milestones set to achieve, it is crucial to understand all the technologies that leaned into it. Also, the security issues to meet the security requirements of its practical implementation. Aiming to that, this paper presents the evolution of CIoV along with the layer abstractions to outline the distinctive functional parts of the proposed architecture. It also gives an investigation of the prime security and privacy issues associated with technological evolution to take measures.

In order to study the effect of explosion load on the flexural performance of RC beams, two RC beams of the same size were carried out explosion test and bearing capacity test successively. Piezoelectric intelligent aggregate was embedded in the beams in advance to monitor the damage state of the beams, which realized the whole process of damage monitoring of the concrete inside the structure from explosion damage to compression damage.Based on wavelet packet analysis and residual bearing capacity damage evaluation criteria, the beam damage was quantitatively evaluated, and the bending bearing capacity of RC beam after explosion damage was compared and analyzed.The results show that the change of concrete strain gauge signal, the phenomenon of crack development and the increase of internal crack development index indicate that the RC beam is damaged by explosion load.After explosion damage, the damage index of the beam increases and the residual bending capacity decreases, which proves that the piezoelectric intelligent aggregate sensor can effectively monitor the bending capacity change of the component after explosion damage.

This study addresses the enhancement of material efficiency and reduction of brittleness in timber-to-concrete adhesive connections for beam-type timber and timber-concrete composite panels. The research explores the potential benefits of adding longitudinal timber ribs to Cross-Laminated Timber (CLT) beam-type panels. Three groups of flexure-tested specimens were analysed: (1) timber panels (1400 mm × 400 mm) with two 100 mm thick CLT panels and two 60 mm thick CLT panels reinforced with 150x80 mm timber ribs; (2) eight specimens (600 mm × 100 mm × 150 mm) with CLT members (600 mm × 100 mm × 100 mm) connected to a 50 mm concrete layer using granite chips and Sikadur-31 (AB) epoxy adhesive; (3) six CLT panels (1400 mm × 400 mm × 50 mm) bonded to a 50 mm concrete layer, with two panels containing polypropylene microfibers and two panels incorporating polyethene dowels for mechanical connection. Specimens were subjected to three-point bending tests and analysed using the transformed section method, γ-method, and finite element method with ANSYS 2023R2 software. Results indicated a 53% increase in load-carrying capacity for ribbed CLT panels with no additional material consumption, a 24.8%-41.1% increase for CLT panels strengthened with a concrete layer, and improved ductility and prevention of disintegration in timber-concrete composites with polypropylene microfibers.

Objective. The present study examined the potential use of computed tomography panoramic mandibular indices on cone beam CT (CBCT) for the assessment of bone density in postmenopausal women with low bone mass. Study design. We enrolled 104 postmenopausal women who performed dual energy X-ray absorptiometry (DXA) using a DXA scanner and mental foramen region CBCT using NewTom VGi EVO Cone Beam 3D system. We assessed the relationship between DXA parameters: lumbar, femoral neck and total hip T score, bone mineral density (BMD), and lumbar trabecular bone score (TBS) and the panoramic mandibular indices: computed tomography mandibular index superior (CTI(S)), computed tomography mandibular index inferior (CTI(I)) and computed tomography mental index (CTMI). Results. We found important correlations between the CTI(I), CTI(S) and CTMI and bone mass, quantitative evaluated as BMD and T-score and also quality using TBS score. Conclusion. CBCT measured indices CTI(S), CTI(I), CTMI are useful in assessing patients with low bone mass.

Water splitting plays an important role in electrochemical and photoelectrochemical conversion of energy devices. Electrochemical water splitting by the hydrogen evolution reaction (HER) is a straightforward route to produce hydrogen (H2), which requires an efficient electrocatalysts to minimize energy consumption. Recent advances have created a rapid rise in new electrocatalysts, particularly those based on non-precious metals. In this review, we present a comprehensive overview of the recent developments of ternary and quaternary 6d-group transition metal chalcogenides (TMCs) based electrocatalysts for water splitting, especially for HER. Detailed discussion is organized from binary to quaternary TMCs including, surface engineering, heterostructures, chalcogen substitutions, and hierarchically structural design in TMCs. Moreover, emphasis is placed on future research scope and important challenges facing these electrocatalysts for further development in their performance towards water splitting.

In this paper, the mechanism of combined process of ion beam sputtering (IBS) and HF acid etching on the chemical structure defects of fused silica and its laser damage resistance perfor-mance were investigated. During the removal process of surface material, the sputtering effect causes lattice atoms to detach from their original positions, forming a large number of unsaturated structures on silica surface, which improves the chemical activity of Si and O atoms, accelerates the chemical reaction process between surface atoms and water molecules, increases the content of hydroxyl (OH-) groups in the shallow layer, and enhances the photothermal weak absorption intensity. However, the presence of OH- groups reduces the bonding strength of Si-O, destroys the spatial network structure of silica bulk, and reduces the mechanical strength of silica surface, resulting in a decrease in its laser damage resistance performance. The paper reveals for the first time the mechanism of IBS to change the structure characteristics of silica material, accelerate the surface hydroxylation process, and thereby reduces the laser damage resistance performance. This work provides technical guidance for effectively suppressing chemical structure defects on silica surface and improving laser damage resistance performance of optical components under high-flux laser irradiation.

Several coatings configurations of combined aluminizing and diffusion layered aluminide on 316 steel were produced and characterized. These coatings, typically employed as thermal barrier coating (TBC), can also be effective as vibration reduction elements at intermediate and high temperatures. This preliminary work has been focused on the microstructural design and processing effects of the coatings. The damping of the produced specimens was measured up to 450°C and compared with that of the steel substrate. The most performing coatings contain an Al-Si layer and exhibit a steep damping increase above 200 °C, reasonably due to dislocation movements by plastic straining of soft alloy layer and to the interface sliding between layers with different elastic moduli.

The crystal structure of quintinite, Mg4Al2(OH)12(CO3)·3H2O, from Jacupiranga alkaline complex (Cajati, São Paulo, Brazil) has been refined for two samples (91002 and C7029) using single-crystal X-ray diffraction data. The mineral crystallizes in the P-3c1 space group, a = 5.246/5.298, c = 15.110/15.199 Å for the samples 91002/C7029. The crystal structure consists of octahedral sheets with Mg and Al ordering according to the 3 × 3 superstructure. The Mg and Al atoms are coordinated by six hydroxylated oxygen atoms each with the average <Mg–O> and <Al–O> bond distances being in the ranges 2.022–2.053 Å and 1.974–1.978 Å, respectively. The interlayer structures are identical (in contradiction to the previous assumptions) and compose from disordered (CO3)2- groups and (H2O)0 molecules. The samples from Jacupiranga can be identified as quintinite-2T that is the second find of the polytype after the Kovdor alkaline complex (Kola peninsula, Russia). The powder X-ray diffraction pattern of quintinite-2T contains weak superstructure reflection at 4.57 Å (010) indicative of Mg and Al ordering. An important crystal-chemical criterion of quintinite is the interlayer distance (d00n-value) of ~ 7.56 Å, which is steady for natural specimens from various findings worldwide.

A novel starch stabilized Mg/Al LDHs material (S-LDH) was prepared in a facile approach and its fluoride ion removal performance was developed. Characterization of S-LDH was employed by using XRD, FTIR and particle size distribution. The adsorption property was studied through the assessment of adsorption isotherms, kinetic models, thermal dynamics and pH influence. The result shows that a low loading of starch of 10 mg onto LDH could obviously improve fluoride removal rate. The S-LDH had 3 times higher adsorption capacity to fluoride than that of Mg/Al LDH to fluoride. The particle size was smaller and the particle size distribution was narrower for S-LDH than that for Mg/Al LDH. Langmuir adsorption isotherm model and pseudo-second-order kinetic model fitted well with the experimental data. In thermodynamic parameters, the enthalpy (△H0) value was 35.63 kJ mol-1 and the entropy (△S0) value was 0.0806 kJ mol-1K-1. The values of △G0 were negative, implying the adsorption process is spontaneous. S-LDH reveals stable adsorption property in a wide pH range from 3 to 9. The mechanism for fluoride adsorption on S-LDH included surface adsorption and interaction ion exchange.

In this study, the team employed full-scale crash tests to investigate the impact of post-densification technology on the safety performance of separated central median W-beam barriers under low compaction conditions. By precisely simulating the design and construction environment of the central median, the study comprehensively evaluated the barrier's containment, redirection, buffering, and anti-intrusion performances, as well as the deformation of both the barrier and vehicles under various collision scenarios. The results indicate that under low compaction soil conditions, the A-level separated central median barriers reinforced with post-densification technology effectively meet the specified protection requirements. By comparing the influence of soil strength variations on barrier performance under simulated rainfall conditions, it was confirmed that enhancing soil compaction significantly improves soil stability, effectively increases the overall strength and stability of the barriers, reduces deformation, and significantly enhances safety performance. This study not only validates the effectiveness of the reinforcement scheme but also provides new perspectives for the scientific research of safety barriers and offers crucial technical support for the optimal design of road safety protection facilities.

As screen sizes are becoming larger and larger, which are beyond human’s physical limitation for direct touching interaction, remote controls are inevitable. However, as techniques applied so far, inertial gyroscopes are susceptible to position inaccuracies, and gesture recognition is limited by cameras’ focus depth and viewing angle. Grating antenna light trapping technology will be an ideal candidate providing the ghost point problem for multipoint inputs can be solved. Therefore, we propose a differential amplitude modulation scheme for grating antenna based multi beam optical touch, which can recognize different incidence points. Where, the amplitude of the incident beams was coded with different pulse width at first. Then, after been trapped by the grating antenna and been transferred into currents by the lined detector arrays, the incident points of the individual beams were recognized and differentiated. The scheme was successfully verified on an 18-inch screen, where two-point optical touch with position accuracy error under 3mm and response time less than 7ms under modulation frequency of 10kHz on both incident beams are obtained. This work paves a practical way for remote multi-point touch, which can make digital mouse in consistent to the users pointing direction obeying natural three-point one ling aiming rule instantaneously.

In order to study the effects of irradiation on the physicochemical properties and digestion behavior of chickpea protein, chickpea protein concentrate (CPC) was treated with electron beam irradiation (EBI) at doses of 5, 10, 15 and 20 kGy, respectively. After irradiation, protein solubility first increased at 10 kGy and 15 kGy, and then decreased at higher dose of 20 kGy. This was supported by SDS-PAGE where the intensity of major protein bands first increased and then decreased. Increased does of EBI generally led to greater oxidative modification of proteins in CPC, indicated by reduced sulfhydryls and increased carbonyls. In addition, protein structure was modified by EBI shown by Fourier transform infrared spectroscopy analysis where α-helix generally decreased and β-sheet increased. Although the protein digestibility was not significantly affected by EBI, the peptidomic analysis of the digests revealed significant difference among CPC irradiated with varying doses. A total of 337 peptides were identified from CPC irradiated with 0 kGy, 10 kGy and 20 kGy, respectively, with 18 overlapping peptides and 60, 29 and 40 peptides specific to the groups of 0, 10 and 20 kGy respectively. Theoretical calculation showed that the distribution of peptide length, hydrophobicity, net charge, and C-terminal residues were affected by irradiation. The 2, 2'-azino-bis (3-ethylbenzothiazoline-6-sulfonic acid) (ABTS) radical scavenging activity showed a marginal decrease with increasing dose of irradiation. In conclusion, EBI led to oxidative modification and structural changes of the chickpea protein, which subsequently affected the physicochemical properties of peptides obtained from in-vitro digestion of CPC despite of similar digestibility.

Imperfection sensitivity of large amplitude vibration of curved single-walled carbon nanotubes (SWCNTs) is considered in this study. The SWCNT is modeled as a Timoshenko nano-beam and its curved shape is included as an initial geometric imperfection term in the displacement field. Geometric nonlinearities of von Kármán type and nonlocal elasticity theory of Eringen are employed to derive governing equations of motion of nano-beam. Spatial discretization of governing equations and associated boundary conditions is performed using differential quadrature (DQ) method and the corresponding nonlinear eigenvalue problem is iteratively solved. Effects of value and location of the geometric imperfection, and the nonlocal small-scale parameter on the nonlinear frequency ratio and imperfection sensitivity of a curved SWCNT for various boundary conditions are investigated. The results show that the geometric imperfection plays a significant role in the nonlinear vibration characteristics of curved SWCNTs.

Chromium (Cr) metal has garnered significant attention in alloy systems owing to its exceptional properties, such as high melting point, low density, and superior oxidation and corrosion resistance. However, its processing capabilities are hindered by the high Ductile-Brittle Transition Temperature (DBTT). Recently, powder bed fusion-laser beam for metals (PBF-LB/M) has emerged as a promising technique, offering the fabrication of net shapes and precise control over crystallographic texture. Nevertheless, research investigating the mechanism underlying crystallographic texture development in pure Cr via PBF-LB/M still needs to be conducted. This study explores the impact of scan speed on relative density and crystallographic texture. At the optimal scan speed, an increase in grain size attributed to epitaxial growth was observed, resulting in the formation of cubic texture. Consequently, a reduction in High Angle Grain Boundaries (HAGB) was achieved, suppressing defects such as cracks and enhancing relative density up to 98.1%. Furthermore, with increasing densification, Vickers hardness also exhibited a corresponding increase. These findings underscore the efficacy of PBF-LB/M for processing metals with high DBTT properties.

Modern Monte-Carlo-based rendering systems still suffer from the computational complexity involved in the generation of noise-free images, making it challenging to synthesize interactive previews. We present a framework suited for rendering such previews of static scenes using a caching technique that builds upon a linkless octree. Our approach allows for memory-efficient storage and constant-time lookup to cache diffuse illumination at multiple hitpoints along the traced paths. Non-diffuse surfaces are dealt with in a hybrid way in order to reconstruct view-dependent illumination while maintaining interactive frame rates. By evaluating the visual fidelity against ground truth sequences and by benchmarking, we show that our approach compares well to low-noise path traced results, but with a greatly reduced computational complexity allowing for interactive frame rates. This way, our caching technique provides a useful tool for global illumination previews and multi-view rendering.

The article describes the study of the properties of polytetrafluoroethylene, modified using natural layered silicates—serpentinite. It is shown that the introduction of a small amount of layered silicates significantly increases the tribological characteristics of the material. The additional introduction of magnesium nano-spinels facilitated the formation of an intercalated polymer-silicate nanocomposite.

To eliminate the influence of the inconsistency on the cycle life and the available capacity of the battery pack, and improve the balancing speed, a novel inductor-based layered bidirectional equalizer (IBLBE) is proposed. The equalizer is composed of the bottom balancing circuits and the upper balancing circuits, and the two layer circuits both consist of a plurality of balancing sub-circuits, which allow the dynamic adjustment of equalization path and equalization threshold. The battery string is modularized by layered balancing circuits to realize fast active equalization, especially for long battery strings. By controlling the bottom balancing circuits, the individual cells can be balanced in each module. At the same time, the equalization between battery modules can be realized by controlling the upper balancing circuits. Simulation and experimental results demonstrate that the proposed equalizer can achieve fast active equalization for a long battery string, and has the characteristics of multi balancing path, large balancing current and high accuracy. The advantages of the proposed equalizer are further verified by a comparison with existing active equalizer.

The dynamics of the topological charge of a vortex optical beam propagating in a turbulent air with accounting for the cubic nonlinearity is theoretically considered. On a number of examples, we show that the optical beam self-focusing manifests itself ambiguously depending on optical wave power. At near-critical values of beam power, self-focusing leads to enhanced spatial localization of optical vortices and substantial suppression of vortex walk-off relative to the beam axis caused by air turbulence. However, with increasing of optical intensity the modulation instability imposed by cubic nonlinearity becomes significant and contributes jointly with medium turbulence to faster divergence of vortex beams.

Lipid composition in the cellular membranes plays an important role in maintaining the struc-tural integrity of cells and in regulating cellular signaling that controls functions of both mem-brane-anchored and cytoplasmic proteins. ATP-dependent ABC and P4-ATPase lipid transport-ers, two integral membrane proteins, are known to contribute to lipid translocation across the li-pid bilayers on the cellular membranes. In this review, we will highlight current knowledge about the role of cholesterol and phospholipids of cellular membrane in regulating cell signaling and how lipid transporters participate this process.

Beam dumps are indispensable components for particle accelerator facilities to absorb or dispose beam kinetic energy in a safe way. However, the design of beam dumps based on conventional technology, i.e. the energy deposition via beam-dense matter interaction, makes the beam dump facility complicated and large in size, partly due to nowadays’ high beam intensities and energies achieved. In addition, these high-power beams generate radioactive hazards, which need specific methods to deal with. On the other hand, the EuPRAXIA project can advance the laser-plasma accelerator significantly by achieving 1-5 GeV high quality electron beam in a compact layout. Nevertheless, the beam dump based on conventional technique will still produce radiation hazards and make the overall footprint less compact. Here, we propose to implement a plasma beam dump to absorb the kinetic energy from the EuPRAXIA beam. In doing so, the overall compactness of the EuPRAXIA layout will not be impacted, and the radioactivity generated by the facility can be mitigated. In this paper, results from particle-in-cell (PIC) simulations are presented for plasma beam dumps based on EuPRAXIA beam parameters.

Crystalline silver thin layers were obtained by high-energy pulsed laser ablation without heating of the deposition substrate. The fluid Plateau-Rayleigh (PRI), Rayleigh – Taylor (RTI) and Richtmyer – Meshkov (RMI) instabilities, as well as crown splash induced during pulsed laser deposition (PLD) in high energy regime, resulting in ring and pearl shaped structures, offer the benefit of increased sorption surface. These morphological structures obtained for the silver thin layers make them of interest for catalytic applications. The study presented with this work addresses both the fundamental and applied issues on the morphological structures obtained for the silver thin layer and their catalytic function in organic processes. In this sense, the catalytic action of the thin silver layer was highlighted by modifications of the Reactive Blue 21 dye (C.I.) in aqueous solution with sodium bicarbonate. Specific investigations and analyzes were carried out by electron microscopy and elemental analysis (SEM-EDX), atomic force microscopy (AFM) and profilometry, mass spectrometry, ablation plasma diagnosis, diffractograms (XRD), as well as IR spectroscopy (FTIR). In addition to the experimental investigation and analyzes, simulation of the ionization energy threshold was conducted in COMSOL for complementary evaluation on the involved processes and phenomena.

Ion current rectification (ICR) is the ratio of ion current by forward bias to by backward bias and is a critical indicator of diode performance. In previous studies, many attempts have been continued to improve the performance of this ICR, but there is the intrinsic problem for geometric changes that induce ionic rectification due to their fabrication problem. Additionally, the high ICR could be achieved in the narrow salt concentration range only. Here, we propose a multi-layered bipolar ionic diode based on an asymmetric nanochannel network membrane (NCNM), which is realized by soft lithography and self-assembly of homogenous-sized nanoparticles. Owing to the freely changeable geometry based on soft lithography, the ICR performance can be explored according to the variation of microchannel shape. Interestingly, very stable ICR performance can be achieved using the multi-layered 3D configuration for the bipolar diode in a broad range of salt concentrations (0.1mM ~ 100 mM). This demonstrates the promising potential of multi-layered NCNM for applications in highly concentrated electrolytes, such as biosensors, desalination, or energy harvesting.

The corrugated board packaging industry is increasingly using advanced numerical tools to design and estimate the load capacity of its products. That is why numerical analyzes are becoming a common standard in this branch of manufacturing. Such trend causes either the use of advanced computational models that take into account the full 3D geometry of the flat and wavy layers of corrugated board, or the use of homogenization techniques to simplify the numerical model. The article presents theoretical considerations that extend the numerical homogenization technique already presented in our previous work. The proposed here homogenization procedure also takes into account the creasing and / or perforation of corrugated board, i.e. processes that undoubtedly weaken the stiffness and strength of the corrugated board locally. However, it is not always easy to estimate how exactly these processes affect the bending or torsional stiffness. What is known for sure is that the degradation of stiffness depends, among other things, on the type of cut, its shape, the depth of creasing, as well as their position or direction in relation to the corrugation direction. The method proposed here can be successfully applied to model smeared degradation in a finite element or to define degraded interface stiffnesses on a crease line or a perforation line.

This study introduces numerical advancements in an alternative design for the SPS Beam Dump Facility (BDF) at CERN. The design envisions a high-power operation target made of flowing liquid lead. The BDF is a proposed versatile facility at CERN, intended for both beam-dump-like and fixed-target experiments. The target behavior is assessed, assuming a proton beam with a momentum of 400 GeV/c, a pulse frequency of 1/7.2 Hz, and an average beam power of 355 kW. An evaluation is conducted using various Computational Fluid Dynamics (CFD) codes to analyze the behavior of liquid lead and to predict the thermal stress on the target vessel induced by the pulsed heat source generated by the charged particle beam. The comparison increases the reliability of the results, investigating the dependencies on the CFD modeling approach. The beam is modeled as a volumetric heat source with data coming from beam-lead interaction simulations provided by CERN and obtained with the Monte-Carlo code FLUKA. The velocity field and stress profiles are utilized to enhance the design of the lead loop and verify its viability and safety when operated with a liquid metal target.

The daily path of the Sun across longitude yields night and day, but the Sun also travels across latitude on a belt 47° wide. The Sun meridian declination explains the annual budget of natural beam irradiance (NBI), which is the irradiance delivered to the Earth’s surface as a normal projec-tion from the Sun. Data for the sun meridian declination data were obtained from the geometric model. The distribution of NBI was weighed between the Tropics of Cancer and Capricorn. The variation patterns of the solar declination conform to the dynamics of pendular motion. The joint distributions of velocity or acceleration of meridian declination against declination fit circular graphs. The NBI budget fluctuates in inverse proportion to the velocity of declination, yielding 18 sun-paths per degree for latitudes above 20°, and 6 sun-paths per degree for latitudes under 20°. All sites of the planet, whose latitude coincide, whether within or between hemispheres, accumu-late an equivalent budget of NBI.

FLASH-RT represents a novel therapeutic radiation modality that holds remarkable potential for mitigating radiation therapy’s adverse side effects. This cutting-edge technology allows for the sparing of healthy tissue while precisely targeting cancerous cells by administering an ultra-high dose-rates of typically between 10 and 30 Gy in less than a few hundred milliseconds. FLASH-RT has demonstrated impressive results in small-animal models, prompting scientists to adapt and advance existing technologies to make it a viable treatment option for humans. However, producing the ultra-high-dose-rate radiation required for the therapy remains a significant challenge. Several radiation sources, such as very high energy electrons (VHEEs), low energy electrons, x-rays, and protons, have been studied for their ability to deliver the necessary dose. Among them, FLASH-x-ray has gained the most attention owing to its capacity to penetrate deeply seated tumours. Despite the complexity of the process, the potential advantages of FLASH-RT make it an exciting area of research. To achieve the FLASH effect, high-frequency, pulsed irradiated accelerator technology can be employed. Sparing healthy tissue, it may allow for more aggressive and effective cancer treatments, leading to a better quality of life for patients. Ongoing research and development will be necessary to refine and optimize this approach to radiation therapy.

The presence of the quantum Rayleigh scattering, or spontaneous emission, inside a dielectric medium such as a beam splitter or an interferometric filter, prevents a single-photon from propagating in a straight-line. Modelling a beam splitter by means of a unitary transformation is physically meaningless because of the loss of photons. Additional missing elements from the conventional theory are: 1) the quantum Rayleigh stimulated emission which can form groups of photons of the same frequencies, and 2) the unavoidable parametric amplification of single-photons in the original parametric crystal. An interference filter disturbs, through multiple internal reflections, the original stream of single-photons, thereby confirming the existence of groups of photons being spread out to lengthen the coherence time. The approach of modelling individual, single measurements with statistical ensemble probability amplitudes leads to the counterintuitive explanations of the experimental outcomes and should be replaced with pure states describing instantaneous measurements which are afterwards averaged.

Damage detection based on modal parameter changes becomes popular in the last decades. Nowadays are available robust and reliable mathematical relations to predict the natural frequency changes if damage parameters are known. Using these relations, it is possible to create databases containing a large variety of damage scenarios. Damage can be thus assessed by applying an inverse method. The problem is the complexity of the database, especially for structures with more cracks. In this paper, we propose two machine learning methods, namely the random forest (RF) and the artificial neural network (ANN) as search tools. The databases we developed contain damage scenarios for a prismatic cantilever beam with one crack and ideal and non-ideal boundary conditions. The crack assessment is made in two steps. First, a coarse damage location is found from the networks trained for scenarios comprising the whole beam. Afterward, the assessment is made involving a particular network trained for the segment of the beam on which the crack is previously found. Using the two machine learning methods, we succeed to estimate the crack location and severity with high accuracy for both simulation and laboratory experiments. Regarding the location of the crack, which is the main goal of the practitioners, the errors are less than 0.6%. Based on these achievements, we concluded that the damage assessment we propose, in conjunction with the machine learning methods, is robust and reliable.

Ni-rich layered cathodes are regarded as a potential candidate for high energy-density lithium-ion batteries, but their high sensitivity to air during storage and poor thermal stability are a vital challenge for large-scale applications. In this paper, an effective solid-solution strategy was proposed to improve the surface and structural stability of Ni-rich layered cathodes by introducing Li2MnO3. The structural analysis results indicate that the formation of Li2CO3 inert layers on Ni-rich layered cathodes during storage in air is responsible for the increased electrode interfacial impedance, thereby resulting in the severe deterioration of electrochemical performance. The introduction of Li2MnO3 can reduce the surface reactivity of Ni-rich cathode materials, playing a certain suppression effect on the formation of surface Li2CO3 layer and the deterioration of electrochemical performances. Additionally, the thermal analysis results show that the heat release of Ni-rich cathodes strongly depends on the charge of states, and Li2MnO3 can suppress oxygen release and significantly improves the thermal stability of Ni-rich layered cathodes. This work provide a method to improve the storage performance and thermal stability of Ni-rich cathode materials.

New hybrid composites based on the inclusion of a vegetal extract, i.e., Boswellia Serrata extract (BSE), rich in boswellic acids, well known as a potent anti-inflammatory natural drug, in a lamellar solid layered double hydroxide (LDH), i.e. a Magnesium Aluminum Carbonate, were developed and characterized in the present work. The adopted LDH exhibits a layered crystal structure, comprised of positively charged hydroxide layers and interlayers composed of carbonate anions and water molecules, thus it was expected to embed negatively charged boswellic acids. In the present case, a calcination process was also adopted on LDH to increase organic acids loading, based on the replacement of original inorganic anions. An accurate investigation was carried out by TGA, PXRD, FT-IR/ATR, XPS and LC-MS to ascertain the nature, interaction, and quantifica-tion of the active molecules of the vegetal extract loaded in the developed hybrid materials. As a result, a significant disruption of the original layered structure was observed in LDH subjected to calcination (LDHc), and this material was able to include a higher amount of organic acids when its composite with BSE was prepared. However, in vitro tests on composites bioactivity, expressed in terms of antimicrobial and anti-inflammatory activity, evidenced LDH-BSE as a better material compared to BSE and to LDHc-BSE, thus suggesting that, though the embedded organic acids amount was lower, they could be more available since not firmly bound to the clay. The composite was able to significantly decrease the number of viable pathogens such as Escherichia Coli and Staphylococcus aureus, as well as the internalization of toxic active species into human cells imposed to oxidative stress in comparison to the BSE.

By solving a Marchenko equation, Green's functions at an arbitrary (inner) depth level inside an unknown elastic layered medium can be retrieved from single-sided reflection data, which are to be collected at the top of the medium. So far, an exact solution could only be obtained if the medium obeys stringent monotonicity conditions and if all forward-scattered (non-converted and converted) transmissions between the acquisition level and the inner depth level are known a-priori. We introduce an alternative Marchenko equation by revising the window operators that are applied in its derivation. We also introduce an auxiliary equation for transmission data, which are to be collected at the bottom of the medium, and a coupled equation, which is based on both reflection and transmission data. We show that the joint system of the Marchenko equation, the auxiliary equation and the coupled equation can be succesfully inverted when broadband reflection and transmission data are available. This results in a novel methodology for elastodynamic Green's function retrieval from two-sided data. Apart from these data, our approach requires P- and S-wave transmission times between the inner depth level and the top of the medium, as well as two angle-dependent amplitude scaling factors, which can be estimated from the data by enforcing energy conservation.

To estimate the progressive collapse resistance capacity of a multi-column frame tube structure with the assembled truss beam composite floor (ATBCF), the pushdown analysis, and the nonlinear dynamic analysis as well, are conducted for such a structure by using the alternate load path (ALP) method. The bearing capacities of the remaining structures at three different work conditions, which are the side middle column failure, the edge middle column failure, and the corner column failure, are individually studied, and the collapse mechanism for the remaining structures is analyzed from the aspects of the internal force redistribution and the failure mode of the second defense line. Simultaneously, the influence of the column failure time on the dynamic response of the remaining structure and the dynamic amplification coefficient are discussed. The results show that the residual bearing capacity of the remaining structure with the bottom corner column failure is higher than that of the one with the side or edge middle column failure, while the latter has a stronger plastic deformation capacity. When the ALP method is adopted to operate the progressive collapse analysis, it is reasonable to take the column failure time as 0.1 times of the first-order vertical vibration period of the remaining structure, and it is suitable to set the dynamic amplification coefficient as of 2.0, which is the ratio of the maximum dynamic displacement to the static displacement of the remaining structure under the transient loading condition.

Based on the elasticity theory, this paper deals with the static analysis of a cracked double beam system in presence of a Winkler medium. The double-beam system is also supposed to be constrained at both ends by elastically flexible springs, with transverse and rotational stiffness. Using a variational formulation, the static governing equations are derived and solved by using analytical and numerical approaches. In the first approach, the closed-form solutions for the displacements functions are obtained based on the Euler-Bernoulli beam theory. In the second approach, the Cell-Discretization Method (CDM) is performed, according to which the two beams are reduced to a set of rigid bars linked together by means of elastic constraints, where the bending stiffness of the bars is concentrated. The resulting stiffness matrix is easily deduced, and the governing equations of the static problem can be immediately solved. A comparative analysis is performed in order to verify the accuracy and validity of the proposed method. This study focuses on the effect of various parameters including the crack depth and position, boundary conditions, elastic medium and slenderness. The validity of the proposed analysis is confirmed by comparing the present results with those obtained from the other approach. In particular, the results obtained by closed-form solution and Cell-discretization method (CDM) are compared by Finite element method (FEM). Accuracy of the results has been evaluated by making comparisons with the results in literature and reported in bibliography. It is demonstrated that the proposed algorithm provides a simple and powerful tool in dealing with the static analysis of a double-beam system. Finally, some concluding remarks are made.

Usually in quantum optics, the theory of large- and small-scale waveguide beam splitters is the same. In this paper it is shown that the theory of the nanoscale waveguide beamsplitter has a significant difference from a similar device, but of a larger scale. It is shown that the previously known theory of the waveguide beam splitter is a particular case of the theory presented here. The wave function at the output ports of the nanoscale beam splitter is analyzed. The results obtained are sensitive to the size of the beam splitter, the coupling parameter of the two waveguides, and the degree of nonmonochromaticity of the photons entering the first and second ports of the beam splitter. The results are important for quantum technologies using a nanosized beam splitter.

Optical modes bearing optical vortices are important light systems in which to encode information. Optical vortices are robust features of optical beams that do not dissipate upon propagation. Thus decoding the modal content of a beam is a vital component of the process. In this work we present a method to decode modal superpositions of light beams that contain optical vortices. We do so using shear interferometry, which presents a simple and effective means of determining the vortex content of a beam, and extract the parameters of the component vortex modes that constitute them. We find that optical modes in a beam are easily determined. Its modal content can be extracted when they are of comparable magnitude. The use of modes of well defined topological charge but not well defined radial-mode content, such as those produced by phase-only encoding, are much easier to diagnose than pure Laguerre-Gauss modes.

Broadband noise reduction over the low-mid frequency range in the building and transportation sectors requires compact lightweight sound absorbers of typical sub-wavelength size. The use of multi-layered closely-spaced (micro-)perforated membranes or panels, if suitably optimized, contribute to these objectives. However, their elasticity or modal behaviors often impede the final acoustical performance of the partition. The objective of this study is to get insights into the vibrational effects induced by elastic limp membranes or panels volumetric modes on the optimized sound absorption properties of acoustic fishnets and functionally-graded partitions (FGP). Cost-efficient global optimization of the partition total frequency-averaged dissipation is achieved from simulated annealing with vibrational effects included through an impedance translation method. Critical coupling analysis reveals how the membranes or panels vibrations redistribute the locations of the Hole-Cavity resonances as well as their cross-coupling with the panels first volumetric mode. It is found that elastic limp micro-perforated membranes broaden the first pass-band of acoustic fishnets while smoothing out the dissipation ripples over the FGP optimiza-tion bandwidth. Moreover, the resonance frequency of the first panels mode sets an upper limit to the broadband optimization of FGPs, up to which high dissipation, low reflection and low trans-mission can be achieved.

We investigated layered titanium nitride (TiN) and aluminum nitride (AlN) for color glasses in Building Integrated Photovoltaic (BIPV) systems. AlN and TiN are among suitable and cost-effective optical materials to be used as thin multilayer films, owing to the significant difference in their refractive index. To fabricate the structure, we used radio frequency magnetron deposition method to achieve the target thickness uniformly. A simple, fast, and cheap fabrication method is achieved by depositing the multilayer films in a single sputtering chamber. It is demonstrated that a multilayer stack that allows light to move from a low refractive index layer to a high refractive index layer or vice-versa can effectively create various distinct color reflections for different film thicknesses and multilayer structures. It is investigated from simulation based on wave optics that, TiN/AlN multilayer offers better color design freedom and cheaper fabrication process as compared to AlN/TiN multilayer films. Blue, green, and yellow color glasses with optical transmittance of more than 80% was achieved by ITO coated glass/TiN/AlN multilayer films. This technology exhibits good potential in commercial BIPV system applications.

Understanding the stability limit of crystalline materials under variable tensile stress conditions is of capital interest for their technological applications. In this study, we present results from first-principles density functional theory calculations that quantitatively account for the response of selected covalent and layered materials to general stress conditions. In particular, we have evaluated the ideal strength along the main crystallographic directions of 3C and 2H polytypes of SiC, hexagonal ABA stacking of graphite and 2H-MoS2. Transverse superimposed stress on the tensile stress was taken into account in order to evaluate how the critical strength is affected by these multi-load conditions. In general, increasing transverse stress from negative to positive values leads to the expected decreasing of the critical strength. Few exceptions found in the compressive stress region correlate with the trends in the density of bonds along the directions with the unexpected behavior. In addition, we propose a modified spinodal equation of state able to accurately describe the calculated stress-strain curves. This analytical function is of general use and can also be applied to experimental data anticipating critical strengths and strains values and providing informattion on the energy stored in tensile stress processes.

Lithium-rich layered oxides is one of the most perspective candidates for cathode materials of lithium ion battery, because of its high discharge capacity. However, there are some disadvantages of uneven composition, voltage decay, and poor rate capacity, which are closely related to the preparation method. Here, 0.5Li2MnO3·0.5LiMn0.8Ni0.1Co0.1O2 were successfully prepared by sol-gel and oxalate co-precipitation methods. A systematic analysis of the materials shows that the 0.5Li2MnO3·0.5LiMn0.8Ni0.1Co0.1O2 prepared by the oxalic acid co-precipitation method has the most stable layered structure and the best electrochemical performance. The initial discharge specific capacity is 261.6 mAh·g-1 at 0.05 C, and the discharge specific capacity is 138 mAh·g-1 at 5 C. The voltage decay is only 210 mV, and the capacity retention is 94.2% after 100 cycles at 1 C. The suppression of voltage decay can be attributed to the high nickel content and uniform element distribution. In addition, tightly packed porous spheres help to reduce lithium ion diffusion energy and improve the stability of the layered structure, thereby improving cycle stability and rate capacity. This conclusion provides a reference for designing high energy density lithium-ion batteries.

In the extra-thick coal seams and multi-layered hard roofs, the longwall hydraulic support yielding, coal face spalling, strong deformations of goaf-side entry, and severe ground pressure dynamic events typically occur at the longwall top coal caving longwall faces. Based on the Key strata theory an overburden caving model is proposed here to predict the multilayered hard strata behaviour. The proposed model together with the measured stress changes in coal seam and underground observations in Tongxin coal mine provides a new idea to analyse stress changes in coal and help to minimise rock bursts in the multi-layered hard rock ground. Using the proposed primary Key and the sub-Key strata units the model predicts the formation and instability of the overlying strata that leads to abrupt dynamic changes to the surrounding rock stress. The data obtained from the vertical stress monitoring in the 38 m wide coal pillar located adjacent to the longwall face indicates that the Key strata layers have a significant influence on ground behaviour. Sudden dynamically driven unloading of strata was caused by the first caving of the sub-Key strata while reloading of the vertical stress occurred when the goaf overhang of the sub-Key strata failed. Based on this findings several measures were recommended to minimise the undesirable dynamic occurrences including pre-split of the hard Key strata by blasting and using the energy consumption yielding reinforcement to support the damage prone gate road areas. Use of the numerical modelling simulations was suggested to improve the key theory accuracy.

The application of adaptive antennas in wireless communication systems is examined in this review of the literature, with particular attention to how well they can transmit and receive signals by dynamically adjusting radiation patterns. The review covers a range of artificial intelligence (AI) approaches that have been used to enhance adaptive antenna performance in beamforming, channel estimation, interference mitigation, and spectrum utilization. Although adaptive antennas have the potential to improve wireless communication systems, the paper also discusses their limitations, including computational complexity, interference sensitivity, and the significance of precise channel state information (CSI) estimates.

In this paper, we dive into the exciting world of wireless communication, focusing on how millimeter-wave technology and Multiple-Input Multiple-Output phased array antennas are shaping the future of 5G and the upcoming 6G technologies. We cover the latest advancements in millimeter-wave and beam-forming technologies, emphasizing their role in enhancing network security and efficiency in automotive vehicles through dual radar communication. Our discussion spans the benefits, applications, challenges, and solutions of these technologies individually from millimeter-wave to beam-forming technology and joint radar communications, alongside a look at their theoretical and practical implementations. We emphasize the integration of beam-forming technology in joint radar communications for future automotive vehicles and its impact on automotive systems, smart cities, and the Internet of Things (IoT). Looking ahead, we discuss the potential of these technologies to transform future tech landscapes, while also addressing the security implications of merging communication and radar capabilities. This paper aims to provide a clear view of the advancements and prospects of millimeter-wave, beam-forming, and dual radar communication technologies.

In this paper, MgAl Layered double hydroxides (LDH) were synthesized by co-precipitation method using a colloid mill and characterized by XRD, IR and SEM. The LDHs was repeatedly tested and compared with different bearing lifetime tester in lithium base grease, and it was found that the environmental-friendly LDHs had greater performance than the traditional antioxidant, and it was the development direction of a new generation of environmental-friendly antioxidants in the future. By adding LDHs into large electric shovel greats (GRK-A) in open-pit coal mine, it can be seen by PDSC evaluation that the service lifetime of grease is extended by 20% while the overall performance of grease is not affected. With the increase of LDHs addition, the grease sample gets the greater activation energy, the stronger thermal oxidation and decomposition resistance. Comparing the energy storage modulus and flow transition index at different temperatures, it can be seen that adding the right amount of LDHs needs close attention for the system oxidation resistance and viscoelasticity. For the electric shovel grease system, the best oxidation resistance and rheological properties can be achieved by adding 2% of LDHs. The rheological viscosity-temperature curves show that the grease samples with different ratios of solid LDHs have better low-temperature properties than the mine grease.

The main objective of this study focuses on designing and testing body protection systems using advanced materials based on aramid fibers, for high impact speeds of up to 410...430 m/s. The investigation of the failure mechanisms identifies issues of protective materials, major challenges and technological problems for efficient development of these systems. The authors presents an investigation on the failure processes and destructive stages of a ballistic package made of succesive layers of LFT SB1plus, taking into account the particular test conditions from NIJ Standard-0101.06 Ballistic Resistance of Body Armor. The main parameter of interest was the backface signature (BFS), but also details of projectile arrest and SEM investigaton could offer arguments in using this material for individual protection.

The microstructures and mechanical properties of the hot-rolled Fe-6.5wt.%Si sheet are analyzed. The microstructure of the hot-rolled sheet is layered along the thickness direction. The surface exhibits fine and equiaxed grains, whereas the center part shows coarse and elongated grains with a <101> fiber texture along the rolling direction. Serrated flow behavior is observed during tensile deformation of both the hot-rolled sheet and its center samples at 350 °C; thus, the serrated flow of the hot-rolled sheet is mainly attributed to the serration of the center part. The analyses of dislocation configurations, ordered structures, and crystal orientation show that the serrated flow behavior results from the interaction of solutes with mobile dislocations. Mobile dislocations are pinned by combining parallel forest dislocations with the pipe diffusion of solution atoms. This study provides a new perspective for the deformation mechanism of the Fe-6.5wt.%Si alloy.

A graphene-containing LDH was prepared by re-hydration of the oxides produced by the calcination of an organic LDH. While the memory effect is a widely recognized effect on oxides produced by inorganic LDHs, it is unprecedented from the calcination/re-hydration of organic ones. Different temperatures (400, 600 and 1100 °C) were tested, on the basis of thermogravimetric data. Water instead of a carbonate solution was used for the re-hydration, with CO₂ available from water itself and/or air to induce a slower process with an easier and better intercalation of the carbonaceous species within the layers. The samples were characterized by X-ray Powder Diffraction (XRPD), IR and Raman spectroscopy and scanning electron microscopy (SEM). XRPD indicate the presence of carbonate LDH mixed with a layered phase with a larger d-spacing. IR confirmed that the prevailing anion is carbonate, coming from the water used for the re-hydration and/or air. Raman data indicated the presence of low-ordered graphenic species moieties and SEM the absence of separated graphene of graphitic sheets, suggesting an intimate mixing of the carbonaceous phase with reconstructed LDH. Organic LDHs gave better memory effect after calcination at 400 °C. Conversely, the graphenic species are observed after rehydration of the sample calcined at 600 °C with a reduced memory effect, demonstrating the interference of the carbonaceous phase with LDH reconstruction and the bonding with LDH layers to form a graphene-LDH nanocomposite.

The independent set, IS, on a graph $G=(V,E)$ is $V^{*}\subseteq V$ such that no two vertices in $V^{*}$ have an edge between them. The MIS problem on G seeks to identify an IS with maximum cardinality, i.e. MIS. $V^{*}\subseteq V$ is a vertex cover, i.e. VC of $G=(V,E)$ if every $e\in E$ is incident upon at least one vertex in $V^{*}$ . $V^{*}\subseteq V$ is dominating set, DS, of $G=(V,E)$ if $\forall v\in V$ either $v\in V^{*}$ or $\exists u\in V^{*}$ and $(u,v)\in E$ . The MVC problem on G seeks to identify a vertex cover with minimum cardinality, i.e. MVC. Likewise, MCV seeks a connected vertex cover, i.e. VC which forms one component in G, with minimum cardinality, i.e. MCV. A connected DS, CDS, is a DS that forms a connected component in G. The problems MDS and MCD seek to identify a DS and a connected DS i.e. CDS respectively with minimum cardinalities. MIS, MVC, MDS, MCV and MCD on a general graph are known to be NP-complete. Polynomial time algorithms are known for bipartite graphs, chordal graphs, cycle graphs, comparability graphs, claw-free graphs, interval graphs and circular arc graphs for some of these problems. We introduce a novel graph class, layered graph, where each layer refers to a subgraph containing at most some k vertices. Inter layer edges are restricted to the vertices in adjacent layers. We show that if $k=\Theta (log\mid V\mid )$ then MIS, MVC and MDS can be computed in polynomial time and if $k=O\left({(log\mid V\mid )}^{\alpha }\right)$ , where $\alpha <1$ , then MCV and MCD can be computed in polynomial time. If $k=\Theta \left({(log\mid V\mid )}^{1+ϵ}\right)$ , for $ϵ>0$ , then MIS, MVC and MDS require quasi-polynomial time. If $k=\Theta (log\mid V\mid )$ then MCV, MCD require quasi-polynomial time. Layered graphs do have constraints such as bipartiteness, planarity and acyclicity.

A series of MgAl-layered double hydroxide (MgAl-HT), the calcined form at 500^oC (MgAlO_x) and the re-hydrated one at 25^oC (MgAl-HT-RH) were synthesized. Physicochemical properties of the catalysts were characterized by x-ray diffraction (XRD), scanning electron microscopy (SEM). Surface area of the as-synthesized, calcined and re-hydrated catalysts was determined by N₂ physisorption at -196^oC. CO₂-teperature programmed desorption (CO₂-TPD) was applied to determine the basic sites of catalysts. The catalytic test reaction was carried out using benzaldehyde and their derivatives with nitromethane and their derivatives. The Henry products (1-15) were obtained in a very good yield using MgAl-HT-RH catalyst either by conventional method at 90^oC in liquid phase, or under microwave irradiation method. The mesoporous structure and basic nature of re-hydrated solid catalyst were responsible for their superior catalytic efficiency. The robust nature was determined by using the same catalyst for five times, where the product % yield was almost unchanged significantly.

The development of printing technologies has enabled the realization of electric circuit fabrication on flexible substrate. However, the current technique remains restricted to single-layer patterning. In this paper, we demonstrate a fully solution-processable patterning approach for multi-layer circuits using a combined method of laser sintering and ablation. Selective laser sintering of silver (Ag) nanoparticle-based ink is applied to make conductive patterns on a heat-sensitive substrate and insulating layer. The laser beam path and irradiation fluence are controlled to create circuit patterns for flexible electronics. Microvia drilling using femtosecond laser through the polyvinylphenol-film insulating layer by laser ablation, as well as sequential coating of Ag ink and laser sintering, achieves an interlayer interconnection between multi-layer circuits. The dimension of microvia is determined by a sophisticated adjustment of laser focal position and intensity. Based on these methods, the flexible electronic circuit with chip-size-package light-emitting diodes was successfully fabricated and demonstrated with functional operations.

We report the growth of graphene at a low temperature using the cold wall chemical vapor deposition technique (CWCVD). Few layered (~6-8 layers) graphene were grown on nickel-coated silicon with acetylene as the precursor gas. The advantage of the combination of the acetylene (as a carbon feedstock) and the nickel catalyst was the lowering of the graphene growth temperature. Nickel coated silicon samples were pre-treated (heat treatment in inert atmosphere) before the growth and the effect of the pre-treatment on the catalyst as well as on the grown film was studied. The final samples were characterized with scanning electron microscopy and Raman spectroscopy. In CWCVD route, the heating of only the substrate holder enabled high heating and cooling rates, which, along with the control over partial pressure of the precursor gas had profound effect on the formation of graphene. In the best sample we have achieved almost equal intensity of the G and 2D peaks in Raman spectrum, which implied about ~6-8 layers of Graphene. The defect peak (the D band) was extremely small in the sample and it was attributed to the ripples and the underlying roughness of the nickel film. We analyzed that a proper choice of the thickness of catalyst layer and a higher cooling rate after graphene growth it would be possible to obtain monolayered graphene. Similar samples grown in a normal atmospheric CVD (with some engineered design to promote fast cooling) were also compared with the cold wall CVD grown samples and plasma assisted CWCVD, and cold-wall CVD demonstrated a better control over the quality of graphene film through the fast cooling and a controlled partial pressure of the precursor gas.

Cantilever beams are the most widely used form of strain-driven energy harvesting, which uses piezoelectric materials. Although researchers are constantly seeking improved power output from cantilever-beam-driven piezoelectric energy harvesters, a systematic and fundamental analysis of the effect of beam geometry on the power capacity of energy harvesters warrants further investigation. Most of the previous research accounts for beams that are fully coated with piezoelectric material. While a larger coating area increases energy output, it also escalates costs as piezoelectric materials are very expensive. Considering the high cost of piezoelectric materials when dealing with limited piezoelectric material, enhancing power output can be achieved by employing a larger base beam and coating a portion of it at the fixed end. As such, the aim of this work is to investigate a wide variety of cantilever beam shapes (e.g., trapezoidal, triangular, V-cut, concave, and convex) with partial piezoelectric material coating on the base beam to maximize the power output capacity of the harvester. To ascertain a comparable argument, the surface area, volume, and mass of all the considered beam shapes are kept consistent, as these parameters influence the power output of the harvester. The geometry of each shape is systematically varied to understand the effect of geometric configuration on the output power density. Finally, the power capacities of all types of beams are compared, and a design is proposed to obtain the maximum power output. It was found that when the surface area of both the beam and piezoelectric material is kept constant and piezoelectric material is located at the fixed end, a trapezoidal beam with a smaller base width and larger free end width is the most efficient in generating power as long as the structural integrity is maintained. The finding is completely opposite as was suggested by previous studies, which proposed that a trapezoidal beam with a smaller free end yields higher output. Instead, this study demonstrates that an inverted trapezoidal beam produced higher output, considering partial coating compared to the full beam coating used in previous studies. Additionally, a correlation is presented on how the beam resonance frequency shifts with variation in beam parameters.

MoS₂/TiO₂ nanostructures made of MoS₂ nanoparticles covering TiO₂ nanosheets have been synthesized, either via ex-situ or in-situ approaches. Morphology and structure of MoS₂/TiO₂ hybrid nanostructures have been investigated and imaged by means of X-ray diffraction (XRD) analysis and high-resolution transmission electron microscopy (HRTEM), while the vibrational and the optical properties have been investigated by Raman, Fourier-transform infrared spectroscopy (FTIR) and UV−visible (UV-Vis) techniques. The different stacking degrees together with the size distribution of the MoS₂ nanosheets, decorating the TiO₂ nanosheets, have been carefully obtained from HRTEM images. The nature of the surface sites on the main exposed faces of both materials has been detected by means of in-situ FTIR spectra of adsorbed CO probe molecule. The results coming from the ex-situ and in-situ approaches will be compared, by highlighting the role of the synthesis processes in affecting morphology and structure of MoS₂ nanosheets, including their curvature, surface defects, and stacking order. Some more, it will be shown that the in-situ approach is affecting the reactivity of the TiO₂ nanosheets too, hence in turn affects the MoS₂/TiO₂ nanosheets interaction.

Biocompatible and biodegradable poly(butylene succinate-co-adipate) (PBSA)/hexadecylamine-modified PPZn (m-PPZn) nanocomposites were prepared using a melt mixing process. Experimental results of wide-angle X-ray diffraction and transmission electron microscopy revealed that the stacking layers of the m-PPZn were partially intercalated and partially exfoliated into the PBSA polymer matrix. The isothermal crystallization kinetics of PBSA/m-PPZn nanocomposites were studied at the temperature range of 62−70 °C and the half-time for crystallization of 3 wt % PBSA/m-PPZn nanocomposite was reduced by 27−35% compared with that of pure PBSA. This finding suggests that the incorporation of m-PPZn might cause the heterogeneous nucleation and the subsequent crystallization growth, which enhances the isothermal crystallization rate of PBSA/m-PPZn nanocomposite. The biodegradation rates of PBSA using Lipase from Pseudomonas sp. increase as the contents of m-PPZn increase. The degradation behavior of the neat PBSA investigated using the change of weight-average molecular weight belongs to exo-type hydrolysis activity. It is necessary to point out that the change of degree of crystallinity and degradation rate are almost linearly proportional to the loading of hexadecylamine-modified PPZn. This finding would provide an important information for the manufacturing biodegradable PBSA nanocomposites.

Efficient beam steerable high-gain antennas enable high-speed data rates over long-distance networks, including wireless backhaul, satellite communications (SATCOM), and SATCOM On-the-Move. These characteristics are essential for advancing contemporary wireless communication networks, particularly within 5G and beyond. Various beam-steering solutions have been proposed in the literature, with passive beam-steering mechanisms employing planar metasurfaces emerging as cost-effective, power-efficient, and compact options. These attributes make them well-suited for use in confined spaces, large-scale production and widespread distribution to meet the demands of the mass market. Utilizing a dual-band antenna terminal setup is often advantageous for full duplex communication in wireless systems. Therefore, this article presents a comprehensive review of the dual-band beam steering techniques for enabling full-duplex communication in modern wireless systems, highlighting their design methodologies, scanning mechanisms, physical characteristics, and constraints. Despite the advantages of planar metasurface-based beam steering solutions, literature on dual-band beam steering antennas supporting full duplex communication is limited. This review article identifies research gaps and outlines future directions for developing economically feasible passive dual-band beam-steering solutions for mass deployment.

In this study, Brillouin optical time-domain analysis (BOTDA) sensing technology was utilized for monitoring settlement in a similarity model of a highway subgrade. As contact winding cannot be used for an optical fiber that is buried directly in soil, uncoupling between. the fiber and the soil can occur. Thus, an optical-fiber-embedded beam (OFEB) was developed, and a method for measuring and calculating the beam deformation was proposed. A calibration test and a test on a similarity model of a subgrade were carried out to investigate the applicability and monitoring accuracy of the OFEB. It was concluded that the OFEB can accurately measure beam deflection, where the maximum relative error between measurements by the optical fiber and a displacement transducer was approximately 5%. The OFEB was embedded directly into a similarity model of a subgrade to monitor settlement. The deflection deformation of the OFEB was found to be close to the subgrade settlement over a certain settlement range with a relative error below 8.1%. Thus, the OFEB can be used to realize measure large-range distributed settlement in a subgrade. A numerical simulation was performed to identify appropriate beam dimensions and material design parameters, thereby extending the measurement range before decoupling of the OFEB and soil occurs. The enhancement of the measurement range and accuracy of the OFEB based on the preliminary experiments carried out in this study enables further investigation of settlement monitoring.

The conventional theory of neutron beams interacting with many-body systems treats the beam as a classical system, i.e. with its dynamical variables appearing in the quantum dynamics of the scattering process not as operators but only as c-numbers. Moreover, neutrons are described with plane waves, i.e. the concept of neutron's (finite) coherence length is here irrelevant. The same holds for electron, atom or X-ray scattering. This simplification results in the full decoupling of the probe particle's dynamics from the quantum dynamics of the scatterer---a well-known fact also reflected in the standard formalism of time-correlation functions (see textbooks). Making contact with modern quantum theoretical approaches (e.g., quantum entanglement, 'which-path detection' versus interference, von Neumann measurement, Week Values, etc.) new observable effects may be exposed and/or predicted, for instance, a momentum-transfer deficit and an intensity deficit in neutron scattering from protons of hydrogen-containing samples. 7

This paper presents an exact solution to the Timoshenko beam theory (TBT) for first-order analysis, second-order analysis, and stability. The TBT covers cases associated with small deflections based on shear deformation considerations, whereas the Euler–Bernoulli beam theory (EBBT) neglects shear deformations. Thus, the Euler–Bernoulli beam is a special case of the Timoshenko beam. The moment-curvature relationship is one of the governing equations of the EBBT, and closed-form expressions of efforts and deformations are available in the literature. However, neither an equivalent to the moment-curvature relationship of EBBT nor closed-form expressions of efforts and deformations can be found in the TBT. In this paper, a moment-shear force-curvature relationship, the equivalent in TBT of the moment-curvature relationship of EBBT, was presented. Based on this relationship, first-order and second-order analyses were conducted, and closed-form expressions of efforts and deformations were derived for various load cases. Furthermore, beam stability was analyzed and buckling loads were calculated. Finally, first-order and second-order element stiffness matrices were determined.

We discuss the implementation of a suite of virtual diagnostics at the FACET-II facility currently under commissioning at SLAC National Accelerator Laboratory. The diagnostics will be used for prediction of the longitudinal phase space along the linac, spectral reconstruction of the bunch profile and non-destructive inference of transverse beam quality (emittance) using edge radiation at the injector dogleg and bunch compressor locations. These measurements will be folded in to adaptive feedbacks and ML-based reinforcement learning controls to improve the stability and optimize the performance of the machine for different experimental configurations. In this paper we describe each of these diagnostics with expected measurement results based on simulation data and discuss progress towards implementation in regular operations.

Layered halide perovskites have emerged as a promising contender in solid-state lighting thanks to their tunable bandgap, high luminescence quantum yield, and high color purity. However, the fabrication of perovskite light-emitting devices in laboratories usually experiences low de-vice-to-device reproducibility since perovskite crystallization is highly sensitive to ambient condi-tions, such as humidity and temperature. Although device processing inside gloveboxes is primarily used to reduce the influence of oxygen and moisture, several extraneous variables, including gas-eous pollution traces and thermal fluctuations in the inert atmosphere or contaminations from re-sidual solvents confined in the enclosed environment, can destabilize the crystallization process and alter the properties of the emissive layers. Here, we examine different experimental set-ups for spin-coating deposition of layered perovskites in inert atmospheres and their influences on the formation of polycrystalline thin films. Our results demonstrate that fluctuations in the glovebox properties (concentrations of residual O2 and H2O or solvent traces), even in very short timescales, can negatively impact the consistency of the perovskite film formation, while thermal variation plays a relatively minor role in this phenomenon. Furthermore, careful storage of chemical species inside the workstation is critical for reproducing high-quality perovskite layers. Consequently, when applying our most controlled environment for perovskite deposition, the photoluminescence life-time of perovskite thin films shows a standard deviation of only 3%, whereas the reference set-up yields a 15% standard deviation. Regarding complete perovskite light-emitting diodes, the uncer-tainties in statistical luminance and EQE data are significantly reduced from 230% and 140% to 38% and 42%, respectively.

Layered double hydroxides (LDHs) have emerged as promising catalysts for various acid-base catalytic reactions. Due to their unique structure and regulatable dual acid-base properties, they offer more environmentally friendly and sustainable alternatives to traditional liquid acid and base catalysts. This study introduces the structural composition, preparation methods, and acid-base catalytic properties of LDHs-based catalysts. Recent application progress of LDHs and rehydrated LDHs, LDHs-based metal nanocatalysts, and LDHs-based mixed metal oxide catalysts used as solid acid-base catalysts in acid-base green catalytic conversion is reviewed. The challenges and prospects of LDHs-based catalysts as green and sustainable catalysts are summarized and proposed.

Over the past two decades, covalent organic frameworks (COFs) have become the most widely studied porous crystalline materials. Its specific physical and chemical properties are determined by the arrangement of atoms (crystal structure). Therefore, the determination of its structure is arguably the most important characterization step for COFs. Although single crystal X-ray diffraction (SCXRD) is the most widely used method for structure determination, the size of COF crystals is too small, or their crystal quality is so poor that confirmation of their structure is limited to lattice fringes by transmission electron microscopy (TEM). At present, many 2D-COFs have clear PXRD patterns, but not all 2D-COFs can obtain specific lattice fringes. This severely hinders the development of the COF field. Here, we discover the lattice shrinkage behavior of COFs under electron beam irradiation by comparing the lattice fringes of 2D-COFs under different conditions. By comparing the lattice fringes of TAPT-TFPT COF at room temperature and under liquid nitrogen freezing conditions, we found that the lattice fringes are in good agreement with the Powder X-ray diffraction (PXRD) and theoretical values of COF (2.213 nm) under freezing conditions, however, the lattice fringe spacing is only 1.656 nm at room temperature. The discovery not only provides new insights into the TEM characterization of COFs, but also further expands the range of crystalline COF materials.

This paper investigates location-based adaptive beamforming techniques, including Maximum Ratio Transmission (MRT) and Zero Forcing (ZF), in complex wireless environments. The study leverages a digital twin simulation of the University of Glasgow campus to evaluate the proposed schemes under realistic conditions, such as user mobility and multipath propagation. The results demonstrate significant performance improvements with the location-based beam steering approaches. In the open space scenario, the location-based schemes achieved up to 40\% higher Signal-to-Interference-plus-Noise Ratio (SINR) and 30\% higher received power, along with reduced interference. The gains were even more pronounced in the digital twin environment, with up to 50\% improvement in SINR and 40\% increase in received power. Furthermore, the study evaluates the energy efficiency of the location-based adaptive beamforming techniques, showing up to 20\% reduction in energy consumption compared to conventional fixed-beam approaches.

Machine Learning (ML) has proved its capabilities in different scientific and industrial fields, but it needs to be further investigated in the construction industry for practical utilization. One of the use cases of ML is delegating the structural calculation process. In this study, to discuss ML’s capabilities in performing the work of a structural designer, calculations of concrete sections based on ACI (American Concrete Institute) as a case study were selected. At first, all manual design steps and standard considerations for a concrete beam section were coded parametrically in MATLAB. After comparing with structural design references to prove the accuracy of codes in calculating shear and bending capacities, the parametric results were used as initial data (Look−up table) for training the ML operators. Regarding different types of ML techniques and as a comparison between them, in the next steps, all essential codes for Fuzzy Logic (FL), Neural Network (NN) and Adaptive Neuro-Fuzzy Inference System (ANFIS) were coded in the same platform. The performance of the three coded ML operators to replace (delegate) standard calculations compared to direct calculations was individually investigated and displayed through parametric examples. After initial examples, the influences of the number of parameters and size of the Look−up table on the accuracy of each operator were discussed. The study concluded that although all three operators can delegate the standard calculation, the precision of the results differs considerably. In case of the desirable size of the Look−up table, ANFIS operators can represent the standard calculations with a different number of parameters and entirely high precision.

A new method for multi-shot reconstruction of high-energy photon distributions in the context of studying the interaction between a beam and a plasma in plasma wakefield acceleration (PWFA) experiments is presented. The study investigates the effects of beam perturbations on betatron radiation and analyzes how these perturbations can lead to hosing, a transverse instability that can degrade the quality of the beam. The potential of betatron radiation spectroscopy as a non-invasive diagnostic technique for PWFA experiments is also emphasized.

The main aspects of material research: material synthesis, material structure, and material properties, are interrelated. Acquiring atomic structure information of electron beam sensitive materials by electron microscope, such as porous zeolites, organic-inorganic hybrid perovskites, metal-organic frameworks, is an important and challenging task. The difficulties in characterization of the structures will inevitably limit the optimization of their synthesis methods and further improve their performance. The emergence of integrated differential phase contrast scanning transmission electron microscopy (iDPC-STEM), a STEM characterization technique capable of obtaining images with high signal-to-noise ratio under lower doses, has made great breakthroughs in the atomic structure characterization of these materials. This article reviews the developments and applications of iDPC-STEM in electron beam sensitive materials, and provides an outlook on its capabilities and development.

A new approach to fabricate TiNi surfaces combining the advantages of both monolithic and porous materials for implants is used in this work. New materials were obtained by depositing a porous TiNi powder onto monolithic TiNi plates followed by sintering at 1200°C. Then, further modification of the material surface with a high-current-pulsed electron beam (HCPEB) was carried out. Three materials obtained (one after sintering and two after subsequent beam treatment by 20 and 30 pulses, respectively) were studied by XRD, SEM, EDX, EIS methods, profilometry and OCP measurements. Structural and compositional changes caused by HCPEB treatment were investigated. Surface properties of the samples during their storage in saline for 10 days were studied and a model experiment with cell growth (MCF-7) was carried out for the sample unmodified with electron beam to detect cell appearance on different surface locations.

A novel quasi-twisted miniaturized wideband Branch Line Coupler (BLC) is proposed. The design is based on bisecting the conventional microstrip line BLC transversely and folding bisected sections on double-layered substrates with a common ground plane in between. The pair of quarter wavelength horizontal parallel arms is converted to a Z-shape meandered microstrip line in the designed structure. On the other hand, the pair of quarter wavelength vertical arms are cut by half into two lines and converted to a periodically loaded slow wave structure. The bisected parts of BLC are placed on the opposite side of the doubled-layer substrate and connected through four vias passing through the common ground plane. This technique enabled a compact BLC size of 6.4×18 mm2, which corresponds to a surface area miniaturization by ~50% as compared to the classical BLC size of 10×23 mm2 at 6GHz, Moreover, the attained relative bandwidth is 73.9% (4.6-10 GHz) for S11, and 75.8% (4.5-10 GHz) for S33 as compared to 41% for the ordinary BLC at the same resonant frequency. The circuit is constructed on a double-layered low-cost FR4 substrate with a relative permittivity of 4.3, and a loss tangent of 0.025. An isolation of -13dB was realized in both S13 and S31 demonstrating an excellent performance. The transmission coefficients between input/output ports S21, S41, S23, and S43 are between -3.1dB to -3.5dB at the frequency of 6GHz. Finally, the proposed BLC provides phase differences between output ports of 90.5o and 94.8o at the frequency of 6GHz when the input ports 1 and 3 are excited, respectively. The presented design offers the potential of being utilized as a unit cell for building a Butler-matrix (BM) for sub-6GHz 5G beamforming networks.

Due to its size, wood dust often plays the role of a raw material used as a source of energy. However, it is nevertheless an unavoidable byproduct generated during the milling of wood or wood-based composites. The research presented here is focused on the selected properties of 3-layer plywood, produced with the utilization of dust from the milling of three-layer particleboard as a filler in the bonding mass. Four types of filler were used in the study: commercial rye flour, wood dust naturally occurring in the composition of particles used industrially for particleboard production, wood dust from the first batch of shredded particleboard, and dust from the second round of milled particleboard. In the context of this investigation, the highest modulus of elasticity (MOE) values were observed in reference samples. Conversely, for samples featuring filler material from the initial milling process, there were no substantial differences in filler content. Notably, in samples where the filler was sourced from the secondary milling of particleboard, the modulus of elasticity exhibited an upward trend in conjunction with increasing filler content. A similar trend was observed in samples utilizing the naturally occurring dust. Meanwhile, the modulus of rupture (MOR) decreased with an elevated degree of milling, though it displayed a slight increase as the filler content increased. With regard to shear strength testing, the most favorable outcomes were achieved in samples incorporating filler material from the initial milling of particleboard. The thickness swelling of the plywood reached its peak in variants utilizing filler material from both the initial and secondary milling of particleboards. In contrast, water absorption testing exhibited a more pronounced response in the newly introduced variants, although samples incorporating filler from the initial and secondary milling processes eventually yielded results akin to the reference sample, with the naturally occurring dust displaying higher water absorption values. In terms of density profiles, the highest density values were observed in samples utilizing rye flour as the filler material. A similar density profile was observed in samples with 5 parts of wood flour as filler, although the density of the adhesive was slightly lower in these cases. An increase in the quantity of wooden filler material resulted in a commensurate increase in plywood thickness. The research confirms the possibility of using the aforementioned dust as an alternative to conventional fillers in plywood technology. It also raises the question of how to effectively remove glue residues from wood-based composite dust, which would enhance their absorption properties.

The resonance spectrum of surface resistance derivative in quasi-two dimensional layered organic conductors has been calculated numerically for the out-of-plane and in-plane magnetic field. Not all but some of the resonances in a given series of transitions are present in the spectra. They are observed at the positions corresponding to the maxima in the surface resistance derivative curve and are in a good agreement with previously calculated magnetic field resonance positions. For tilted magnetic fields, there are more resonances present in the spectrum than in the case of a non-tilted field. Apart from the resonances corresponding to the transitions between the adjacent surface states there also appear resonances involving the transitions between the more distant surface states. This is correlated with the specific topology of Fermi surface of the organic conductors. The presented calculations will allow correct interpretation of the experimental curves for the resonance spectrum, and also to obtain information on the surface properties of these materials for their possible implementation in fabrication of devices based on organic molecular conductors.

In this study, Li-Al-OH layered double hydroxide (LDH), which was prepared by solvent-free one-step mechanochemical reaction of LiOH and Al(OH)₃, was applied to remove boron from aqueous solution. Dry-grinding for 3 h at a rotational speed of 500 rpm, Li/Al molar 1/2 was the optimum condition to prepare highly crystalline of Li-Al LDH phase with no evident impure phases. Two milling products with Li/Al molar ratio at 1/2 and 2/2 were evaluated for boron adsorption. The results confirmed that Li/Al molar ratio 2/2 sample showed high boron adsorption capacity due to the physical adsorption of Li-Al-OH LDH and chemical synergism of phase gel Al(OH)₃. The adsorption isotherms, described by the Langmuir model, indicated maximum monolayer boron uptake capacity 45.45 mg/g, implying competitive adsorption capacity of the material in our experiment.

Most IoT systems meant for implementing mission-critical systems are multi-layered based. The majority of the computing is done in the services and gateway layer. The Gateway layer connects the Internal section of the IoT to the cloud through the Internet. The failure of any node between the services servers and the gateways will isolate the entire network leading to zero tolerance. A networking topology is required to connect the service servers to the gateways, yielding 100% fault tolerance. Empirical formulation of the model chosen to connect the service’s servers to gateways through routers is required to compute the fault tolerance of the network. Rectangular and Interstitial Mesh have been proposed in this paper to connect the service servers to the gateways through the servers that yield 0.999 fault tolerance of the IoT network. An empirical formulation is also presented using which the Fault tolerance of the IoT network can be computed. An enhancement of 11% in the fault tolerance capability of an IoT network has been achieved by implementing Rectangular and Interstitial Mesh in the gateway layer of the network.

Lithium rich layered oxides (LRLO) are a wide class of innovative active materials for positive electrodes in lithium-ion (LIB) and lithium-metal secondary batteries (LMB). LRLOs are over-stoichiometric layered oxides rich in lithium and manganese, with general formula Li1+xTM1-xO2, where TM is a blend of transition metals comprising Mn (main constituent), Ni, Co, Fe and others. Due to the very variable composition and the extended defectivity their structural identity is still debated among researchers being likely an unresolved hybrid between a monoclinic (mC24) and a hexagonal lattice (hR12). Once casted in composite positive electrode films and assembled in LIBs or LMBs, LRLOs can delivery reversible specific capacities above 220-240 mAhg-1, thus beyond any other available intercalation cathode material for LIBs, with mean working potential above 3.3-3.4 V vs Li for hundreds of cycles in liquid aprotic commercial electrodes. In this review we critically outline the recent advancements in the fundamental understanding of the physico-chemical properties of LRLO as well as the most exciting innovations in their battery performance. We focus in particular on the elusive structural identity of these phases, on the complexity of the reaction mechanism in batteries as well as on practical strategies to minimize or remove cobalt from the lattice while preserving the outstanding performance upon cycling.

In a concrete beam initially crack is generated at the tension side under the effect of flexure, shear and torsional loadings. Accordingly, these weak concrete members require repair and/or strengthening to increase or restore their internal load capacity. In the current experimental and numerical investigations on concrete beam having different width to depth ratio of notch on its ultimate flexural load under one-point loading was considered. Further, the flexural behavior performance of notch concrete beam repaired with the three repair materials cement mortar, bacterial mortar and adhesive was also examined. Consequently, a comparative study is imple-mented between the experimental and numerical results. Concrete Damage plasticity (CDP) model was used for finite element numerical analysis of beam. The differences in numerical and experimental measured results ranges from 0.65 - 22.20 % for the ultimate load carrying capacity. As the notch size increases the ultimate load carrying capacity of beam was reduced. Addition-ally, linear regression model is used to predict the ultimate load values at an interval of 5 mm notch width up to maximum width of notch 100 mm. It can be observed that the ultimate load capacity for repaired beam is increased as compared to the notch beam for all the three repairing materials under consideration. The maximum ultimate load was increased in case of notch beam repaired using adhesive. As compared to the cement mortar the performance of the bacterial mortar in terms of the ultimate load was more. The bacterial mortar is found more sustainable and more durable as a repair material for the concrete structures.

The performance of modern wireless communication systems is highly dependent on the adoption of multiple antennas and the associated signal processing. In 5G and 6G networks, beamforming and beam management become challenging tasks due to aspects such as user mobility, increased number of antennas, and the adoption of higher frequencies. Artificial intelligence, and more specifically, machine learning, are efficient tools to reduce the complexity involved in generating beams and the overhead associated with beam management without sacrificing system performance. Therefore, AI-aided beamforming and beam management have received a lot of attention recently. This article presents a complete survey on this topic, emphasizing open problems and promising directions. The discussion includes architectural and signal processing aspects of modern beamforming and beam management. The article presents communication problems and respective solutions using centralized/decentralized, supervised/unsupervised, semi-supervised, active, federated, and reinforcement learning.

Adaption of laser communication terminals to airborne and lean-satellite platforms is now a vogue, made possible due to the progressing advancements in lightweight components and compactness of onboard electro-optical transceivers and control systems. This enables highly secured and superior data-transmission rates beyond multiple Gigabit/second on CubeSats and drones compared to Megabit/second rates offered by similar radio-transceivers form factors. However, laser-transmission links require a very stringent beam-pointing stability because they are easily perturbed by attitude variations and micro-vibrations generated by the host platform’s propulsion system or other mechanically active subsystems in proximity with the transmitter’s optical head. Severe line-of-sight jitter causes the downlink laser beam to drift from the targeted receiving system’s field-of-view, inducing pointing errors, increasing signal outage probability and information loss. We experimentally examine the platform jitter generated by the propellers of an hexacopter drone during ground operation and the attitude-control unit’s reaction wheels in a 6U CubeSat structure. We determined the vibration spectrum unique to these platforms and accordingly prescribe requirements for applicable optical fine pointing and disturbance isolation or suppression systems needed to achieve a high-fidelity laser-communication link.

This paper presents an advanced software tool for precise laser beam propagation analysis, focusing on the calculation of the M2 value, a key measure of beam quality. Developed in Python, the software integrates libraries like NumPy, Matplotlib, and SciPy for robust data handling and accurate polynomial fitting. It features a user-friendly interface for easy data input, analysis, and visualization, making it accessible to both professionals and novices. The tool has been rigorously validated against theoretical models (M2=1) and experimental data (showing M2=1.2548 and 1.3166), ensuring high accuracy and reliability. It visualizes beam width data and fitted polynomial curves, aiding in assessing beam propagation characteristics and optimizing laser systems. Future enhancements include additional beam quality metrics, machine learning integration, and cloud-based functionality. This tool significantly advances laser beam analysis, benefiting research and industrial applications by improving performance and efficiency. The software is available at DOI: 10.5281/zenodo.13325911

A composite beam is a structural member that behaves as a single unit by using shear connectors between a concrete slab and an H-shaped steel girder. The composite ratio is crucial and determined by the shear connectors' ability to withstand the horizontal shear forces between the concrete and steel girder. In this study, a U-shaped composite beam was designed, which differs from conventional composite beams as it allows the use of a steel girder as a formwork. Moreover, angle-type shear connectors, instead of stud-type connectors, were employed. Based on this design, large-scale U-shaped composite beams with angle-type shear connectors were fabricated, and load tests were conducted to analyze the behavior after composite action and the influence of shear connector spacing. Additionally, the strength of the angle-type shear connectors used in this paper was evaluated through finite element analysis. Finally, a strength evaluation method for composite beams of this configuration was proposed.

This paper presents the experimental and numerical study on a ductile beam-column connection between a composite reinforced concrete truss (CRCT) beam and Concrete Filled Tube (CFT) column subjected to bending and shear loads. Two experimental models with different beam-column joint testing schemes, extracted from the same prototype three-dimensional structure designed according to the rules of the capacity design provided by seismic code, were subjected to quasi-static cyclic tests by applying gravitational loads and the horizontal seismic force. The main objective of this paper is to verify the experimental ductile behavior of both specimens and to simulate the experimental global and local response by nonlinear static analysis considering different modelling approaches. The comparison between the experimental and numerical results highlights, for both models considered, the ductile and dissipative capacity of the connection system, designed following the criterion of the hierarchy of resistances proposed by the current Italian code. Different experimental setup showed similar results demonstrating the repeatability of the test and its reproducibility through the nonlinear numerical analysis.

We investigate numerically the interactions of in-phase Airy beams modulated by a fundamental Gaussian beam and fourth-order diffraction in Kerr nonlinear media. Directly numerical simulations show that normal (anomalous) fourth-order diffractions and in-phase (out-of-phase) Gaussian beam affect the interactions of solitons generated from Airy beams in unique manners. Different from previous results that interactions between in-phase (out-of-phase) conventional beams are always attractive (repulsive), many anomalous interactions of Airy beams are obtained. Stable bound states of breathing Airy soliton pairs can be formed with the help of fourth-order diffraction and fundamental Gaussian beam.

The extensive utilization of rebar during the construction of the project generates immense rebar waste, leading to increased construction costs and significant greenhouse gas emissions. Various approaches have been explored focusing on the minimization of rebar-cutting waste, such as optimizing cutting patterns, lap splice position, and special-length rebar utilization. Nonetheless, reducing rebar usage by minimizing the number of splices remains uninvestigated. In response to these issues, a two-stage optimization algorithm was developed, prioritizing special-length rebar to achieve near-zero rebar-cutting waste of less than 1% and concurrently reduce rebar usage, thereby promoting sustainable construction practices. The two-stage algorithm presented in this study involves the optimization of the lap splice position for the continuous rebar with a reduction of splices number. Furthermore, it integrates a special-length minimization algorithm for the additional rebars. Applying the algorithm to beam structures in a small-sized factory building project led to a notable reduction of 29.624 tons of rebar, equivalent to 12.31% of the total purchased quantity. Greenhouse gas emissions were reduced by 102.68 tons, and associated costs decreased by USD 30,256. A rebar-cutting waste of 0.99% which is near zero was achieved. These findings highlight the significant potential of the proposed algorithm in reducing rebar waste and facilitating sustainable construction practices. In addition, the application of the proposed algorithm in reinforced concrete construction projects will amplify the associated advantages accordingly.

The behaviour of steel frame buildings under progressive collapse conditions depends on a combination of several parameters including the interplay between different collapse resistance mechanisms mobilized in different structural components. Previous studies have shown that the extent to which these mechanisms may contribute to progressive collapse resistance depends on the ability of the beam-column connections to undergo large inelastic deformations prior to reaching their deformation capacity limits. For this reason, and due to the important role of their flexural strength and tying capacity in the development of essential collapse resistance mechanisms, the response of beam-column connections is one of the most important features of progressive collapse performance. Based on the knowledge gained through previous studies on the mechanics of the problem, the role of the connections is critically reviewed by examining the results of several experimental studies conducted during the past decade. The factors that may adversely affect progressive collapse resistance – such as failure modes of certain connection types – are evaluated, and novel approaches of limiting these factors which are currently under development are reviewed. The assessment of these parameters leads to useful conclusions of practical significance, while highlighting the aspects of the problem that need further study and understanding.

Aerated concrete, which is manufactured from binding material, sand, foaming agent and water, is currently being utilized in the construction industry because of its lightweight and durability. The binding material, cement, along with other materials used in the concrete produces huge carbon footprints during its fabrication. The utilization of natural aggregates name as coarse aggregates depletes the natural resources of the country. Therefore, huge amounts of agricultural wastes have led scholars to investigate the effectiveness of replacing conventional materials used in concrete with agricultural wastes. In the current study, rice husk ash (RHA) was used as supplementary cementing material, thereby reducing the amount of cement used in aerated concrete (AC) mixture will reduce carbon footprints. The experimental and numerical analysis were conducted to investigate structural behavior of reinforced RAC- B beams subjected to flexural load. Parametric study on structural performance of RAC- B beam under flexure were conducted using finite element analysis (FEA). From the experiment and FEA. Results from the parametric study showed that RAC-10%RHA-B with higher depth structurally performed better compared to RAC-B under flexure with greater load carrying capacity, lesser maximum deflection, and less cracks developing in the tension area.

Ocean surface currents and winds are tightly coupled essential climate variables, and, given their short time scales, observing them at the same time and resolution is of great interest. DopplerScatt is an airborne Ka-band scatterometer that has been developed under NASA's Instrument Incubator Program (IIP) to provide a proof of concept of the feasability of measuring these variables using pencil-beam scanning Doppler scatterometry. In the first half of this paper, we present the Doppler scatterometer measurement and processing principles, paying particular attention to deriving a complete measurement error budget. Although Doppler radars have been used for the estimation of surface currents, pencil-beam Doppler Scatterometry offers challenges and opportunities that require separate treatment. The calibration of the Doppler measurement to remove platform and instrument biases has been a traditional challenge for Doppler systems, and we introduce several new techniques to mitigate these errors when conical scanning is used. The use of Ka-band for airborne Doppler scatterometry measurements is also new, and, in the second half of the paper, we examine the phenomenology of the mapping from radar cross section and radial velocity measurements to winds and surface currents. To this end, we present new Ka-band Geophysical Model Functions (GMF's) for winds and surface currents obtained from multiple airborne campaigns. We find that the wind Ka-band GMF exhibits similar dependence to wind speed as that for Ku-band scatterometers, such as QuikSCAT, albeit with much greater upwind-crosswind modulation. The surface current GMF at Ka-band is significantly different from that at C-band, and, above 4.5 m/s has a weak dependence on wind speed, although still dependent on wind direction. We examine the effects of Bragg-wave modulation by long waves through a Modululation Transfer Function (MTF), and show that the observed surface current dependence on winds is consistent with past Ka-band MTF observations. Finally, we provide a preliminary validation of our geophysical retrievals, which will be expanded in subsequent publications. Our results indicate that Ka-band Doppler scatterometry could be a feasible method for wide-swath simultaneous measurements of winds and currents from space.

In this paper, we study the well-posedness and asymptotic behaviour of solutions to a laminated beam in thermoelasticity of type III. We first give the well-posedness of the system by using the semigroup method. Then, we show that the system is exponentially stable under the assumption of equal wave speeds. Furthermore, it is proved that the system is lack of exponential stability for case of nonequal wave speeds. In this regard, a polynomial stability result is proved.

In previous work (Z. Angew. Math. Phys. 68(2), 2017), Apalara considered a one dimensional thermoelastic laminated beam under Cattaneo’s law of heat conduction and proved the exponential and polynomial decay results depend on the stability number χ_T . In this paper, we continue to study the same system and show that the solution of the concerned system lacks of exponential decay result in the case χ_T ≠ 0 which solves the open problem proposed by Apalara (Z. Angew. Math. Phys. 68(2), 2017).

In a saline semi-isolated Lagoon on the Cape Zeleny (White Sea), the annual dynamics of the vertical hydrological structure, and the seasonal dynamics of phytoplankton were traced, including species composition, and vertical distribution, abundance, nutrition type,and biomass.293 species and supraspecific taxa of algae and cyanobacteria were found. Most of the identified species are marine, and 38 species are freshwater. Taxonomic composition changed in the Lagoon during the year. Dinoflagellates dominated in winter and early June; unidentified cocci and flagellates in July; diatoms, dinoflagellates and unidentified cells in August; dinoflagellates in September; and unidentified cocci and flagellates in October–November. The abundance of algae also changed in the Lagoon during the year. The integrated biomass in the water column varied from 0.01 g C/m2 in January to 0.78 g C/m2 in early September. According to the abiotic parameters, the water column of the Lagoon is subdivided into several zones with different conditions and corresponding phytoplankton communities. Similarity between the communities of different horizons was 32-46% in summer and 7% in winter. The chemocline layer was the most populous. Almost the entire year it contained a maximum of phytoplankton biomass, 1-2 orders of magnitude higher than that in the overlying horizons. Comparison phytoplankton in the lagoon and in the nearby sea area was carried out. Despite the connection between the Lagoon and the sea phytoplankton structure in the surface water layer in the Lagoon and in the sea differs significantly in composition, quantitative parameters, and seasonal dynamics. The similarity of the communities in the sea and the Lagoon never exceeded 50%. In terms of biomass, the Lagoon lags behind the sea until mid-summer, but, starting from August, it outnumbers it, and the phytoplankton development in the Lagoon lasts longer, until late autumn. The phytoplankton structure and dynamics in the Lagoon and the sea by 24.5% was related to the daylight, water salinity, oxygen content and pH, but did not depend on water T, underwater illuminance, and depth. Oxygen content and pH are defined by PhP activity. Salinity serves as a vector of the vertical sequence of ecological niches. The daylight length seems to be the crucial factor of the seasonal PhP dynamics in the semi-isolated coastal stratified lakes and lagoons.

Nano- and micro-sized CeO2 surface layers based on titanium alloy TiAl6V4 were obtained by magnetron sputtering with or without subsequent annealing. The structure of the samples was determined using scanning electron microscopy, Auger electron spectroscopy, energy dispersive spectroscopy, and X-ray diffraction. Hardness was measured by sclerometry. A direct linear dependence of the thickness of the surface layers on the deposition time and an extreme dependence, passing through a maximum, on the power are shown. A decrease in hardness with an increase in the thickness of the cerium oxide coating was noted. An increase in surface roughness, delamination and loosening of the surface layer, presumably associated with annealing, were noted. In samples with a surface layer thinner than 715 nm without annealing and 750 nm after annealing, the formation of a sublayer of TiO2, Al2O3, and Ce(VO4) was found, and in annealed samples with a layer length of less than 300 nm, all cerium dioxide reacted with vanadium dioxide to form vanadate.