The paper presents a method to assess the effect of electrolyte additives on the energy capacity of Pb-acid batteries. The method applies to any chemically unreactive additive, including suspensions and gels. The approach is thermodynamically based and it leads to the definition of a region of admissible concentrations –the battery’s admissible range– where the battery can undergo an indefinite number of charge/discharge cycles without suffering permanent damage. An experimental procedure to determine this range is presented. The obtained results provide a way to assess the potential of electrolyte additives to improve the energy capacity of Pb-acid batteries. The same results also provide a means to determine the additive concentration that produces the maximum energy capacity increase of the battery. The paper closes with an example of application of the proposed approach to a practical case.

Electrochemical Impedance Spectroscopy techniques were applied in this work to 9 lead-acid battery prototypes fabricated industrially, divided on three type/technology packages. Frequency dependent impedance changes were interpreted during successive charge/discharge cycles on two distinct stages: 1) immediately after fabrication; and 2) after a controlled aging procedure to 50% Depth of Discharge, following industrial standards. By investigating their State of Health behaviour vs electrical response, three methods were employed, namely the (Q-Q0) total charge analysis, the decay values of Constant Phase Element in the equivalent Randles circuits, and the resonance frequency of the circuit. A direct correlation has been found for prediction of the best performant batteries in each package, thus allowing a qualitative analysis capable to provide the decay of the battery State of Health. We emphasized which parameters are directly connected with their lifetime performance in both stages, and by consequence, which type/technology battery prototype emphasize the best performance. Based on this methodology, the industrial producers can further establish the quality of the novel batteries in terms of performance vs lifespan, allowing them to validate the novel technological innovations implemented in the current prototypes.

This paper proposes the recycling of plates from spent car batteries by the melt quenching method and the incorporation of NiO or Co3O4 contents in order to improve the electrochemical performance of new materials for applications as electrodes on batteries. The analysis of X - ray diffractograms indicates the gradual decrease of the sulfated crystalline phases, respectively 4PbO•PbSO4 and PbO•PbSO4 phases until their disappearance for higher dopant concentrations. IR data show a decreasing trend in the intensity of the bands assigned to sulfate ions and a conversion of [PbO3] pyramidal units into [PbO4] tetrahedral units by doping with high dopant levels yielding to the formation of the PbO2 crystalline phase. The EPR data indicate three resonance lines centered on the gyromagnetic factor, g ~ 2, 2.2 and 8, which are dependent on the NiO level. The first two resonance lines are assigned to nickel ions in higher oxidation states and the last signal centered at g ~ 8 corresponds to nickel metal nanoparticles. This compositional evolution can be explained by considering a process of drastic reduction of nickel ions in oxidation states superior to metallic nickel. The linewidth and the intensity of resonance lines situated at about g ~ 2, 2.17, 4.22 and 7.8 corresponding to the Co+2 ions from EPR spectra depend very strongly on the Co3O4 concentration. The best reversibility of the cyclic voltammograms was highlighted for the samples with x = 8 mol% NiO and 10 mol% Co3O4, which are recommended as suitable in applications as electrode for renewable batteries.

In this paper, carbon nanotubes modified screen-printed electrode (CNTs/SPE) was prepared and the CNTs/SPE was employed for the electrochemical determination of antioxidant substance Chlorogenic acids (CGAs). A pair of well-defined redox peak of CGA was observed at the CNTs/SPE in 0.10 mol∙L^-1 acetic acid-sodium acetate buffer (pH 6.2) and electrode process is adsorption-controlled. Cyclic voltammetry (CV) and differential pulse voltammetry (DPV) method for the determination of CGA were proposed based on the CNTs/SPE. Under the optimal conditions, the proposed method exhibited linear ranges from 4.73×10^-7 to 4.45×10^-5 mol∙L^-1, the linear regression equation was Ipa(µA) = 4.1993 C (mol∙L^-1)+1.1039 (r = 0.9976) and the detection limit for CGA could reach 3.25×10^-6 mol∙L^-1. The recovery of matrine was 94.74~106.65% (RSD = 2.92%) in coffe beans. The proposed method is quick, sensitive, reliable, and can be used for the determination of CGA.

To stabilize the Earth’s climate a large-scale transition is needed to non-carbon emitting renewable energy technologies like wind and solar energy. Although these renewable energy sources are now lower-cost than fossil fuels, their inherent intermittency make them unable to supply a constant load without storage. To address these challenges rechargeable electric batteries are currently the most promising option; however, their high capital costs limit current deployment velocities. To both reduce the cost as well as improve performance 3D printing technology has emerged as a promising solution. This literature review provides the state-of-the-art enhancements of battery properties with 3D printing including efficiency, mechanical stability, energy and power density, customizability and sizing, production process efficiency, material conservation and environmental sustainability as well as the progress in solid-state batteries. The principles, advantages, limitations, and recent advancements associated with the most common types of 3D printing are reviewed focusing on their contributions to the battery field. 3D printing batteries offer design flexibility, material flexibility, reduces pack weight, minimizes material waste, increases the range of applications and has the potential to reduce costs. As 3D printing technologies become more accessible, the prospect of cost-effective production for customized batteries is extremely promising.

The refractive index of a liquid serves as a fundamental parameter reflecting its composition, thereby enabling the determination of component concentrations in various fields such as chemical research, food industry, and environmental monitoring. Traditional methods for refractive index (RI) measurement rely on light deflection angles at interfaces between the liquid and a material of known refractive index. In this paper, the authors present a new differential refractometer for highly sensitive measurement of RI differences between two liquid samples. Using a configuration with two cells equipped with flat parallel plates as measuring elements, the instrument facilitates accurate analysis. Namely, the sensor signals from both the solution and the solvent cuvette are generated simultaneously with one laser pulse, reducing the possible fluctuations of the laser radiation intensity. Our evaluation shows the high sensitivity of RI measurements (< 7 · 106), so this differential refractometer can be proposed not only as a high-sensitivity sensing tool that can be used for mobile detection of nanoparticles in solution samples, but also to determine the level of environmental nano-pollution using water (including rain, snow) samples from various natural as well as industrial sources, thus helping to solve some important environmental problems.

Rapid industrialization, urbanization, and population explosion in sub-Saharan Africa escalate environmental Lead levels with subsequent elevation of blood Lead levels in children. Nutrition status, age, and genetics govern one’s susceptibility to Lead toxicity. This study expounded this susceptibility by relating blood Lead levels, d-aminolevulinic acid dehydratase enzyme activity (ALAD), and genetic variations of proteins that code for ALAD enzyme in urban children of Uganda. Spectrophotometric analysis for blood Lead (BL), hemoglobin levels, and determination d-levels aminolevulinic acid dehydratase enzyme activity of the blood samples from 198 children were performed prior to a polymerase chain reaction and restriction fragment length digestion for ALAD polymorphism was done. Up to 99.5% of samples coded for the ALAD1 allele whereas 0.05% coded for ALAD2. Genotypes ALAD2-2 members had elevated BLL (mean 14.1 µg/dL) and reduced ALAD enzyme activity compared to others. This, therefore, implies that the majority of children hoard BL which may affect them later in life.

Lead Acid Batteries (LABs) are used for starting, lighting, and igniting, as well as in air conditioning systems and to supply power to electric engines in transport vehicles (TVs). However, the application of LABs for TVs has faced a number of market challenges, mounted by the upcoming high energy density and long lifespan batteries, such as lithium ion. LABs, on the other hand, are inexpensive. The key research question is, how can the lifespan of LABs used in automotive industries be increased, while still ensuring a low cost solution? Thus, integrating LABs with the supercapacitor (known as an electric double layer capacitor—EDLC) is likely to outperform the competing alternative batteries for TVs. This paper proposes a multiple stage approach to hybrid lead acid batteries and a supercapacitor system for TVs that is capable of maintaining the battery state-of-charge (SOC) at statistically high limits, ranging between 90% and 95%. This SOC target will likely ensure that the lifespan of the hybrid battery system can be elongated (extended) more than its competitors. In this study, the multiple stage approach of concatenated converters has been designed in order to satisfy all energy storage requirements for different characteristics of LABs and the supercapacitor. The designed hybrid system has been simulated using Matrix Laboratory (MATLAB/Simulink (version R2016a, MathWorks, Natick, MA, USA)). The simulated results show that high transient currents from the direct current (DC) bus of LABs, caused by the regenerative braking or deceleration of the TVs, reduce the battery lifespan and induce mechanical stress. The supercapacitor reduces the stress on the LAB by absorbing high transient currents. This, in turn, keeps the LABs’ SOC between 90% and 96% and the voltage at 12 V. As indicated by the simulated results, the hybrid battery SOC is maintained at 90–96% and the terminal voltage is approximately 12 V.

Accurate and efficient battery modeling is essential to maximize the performance of isolated energy systems and to extend battery lifetime. This paper proposes a battery model that represents the charging and discharging process of a lead-acid battery bank. This model is validated over real measures taken from a battery bank installed in a research center placed at “El Chocó”, Colombia. In order to fit the model, three optimization algorithms (Particle Swarm Optimization, Cuckoo Search, and Particle Swarm Optimization+Perturbation) are implemented and compared, being the last one a new proposal. This research shows that the model with the proposed algorithm is able to estimate and manage the real battery characteristics as SOC and charging/discharging voltage. The comparison between simulations and real measures shows that the model is able to absorb reading problems, signal delays, and scaling errors. The approach we present can be implemented in other types of batteries especially those used in stand-alone systems.

Direct-to-blister copper flash smelting slag contains up to 14% of copper and 2-4% of lead. Considering this fact, this material is subjected to the high-temperature reduction process. After this, converting process is performed on the Cu-Pb-Fe alloy being the product of decopperization process in electric furnace. An alternative to the presently used processing of flash smelting slag would be its hydrometallurgical treatment and selective recovery of Pb and Cu. This paper presents the results of laboratory tests on flash smelting slag leaching with citric acid solutions. The experiments performed allowed to determine the process parameters at which the Pb concentration in the post-leaching sediment reached the value of 0.41-0.6% while the Pb content in flash smelting slag was 3.05%. Analogous values for copper were 11.5-11.8% (after leaching) and 12.44% (before). Material after leaching in citric acid solutions can be processed, in the second step, using sulfuric acid solutions, and it could lead to the recovery of almost all copper contained in it.

Four naturally occurring zeolites AZLB-Ca and AZLB-Na (Bowie, Arizona), NM-Ca (Winston, New Mexico), and NV-Na (Ash Meadows, Nevada) were studied to evaluate structural modifications after treatment with HCl acid. AZLB-Ca and AZLB-Na are chabazite-like species and become amorphous when boiled in concentrated HCl acid as confirmed by powder X-ray diffraction. In contrast, NM-Ca and NV-Na which are clinoptilolite-like species withstood boiling in concentrated HCl acid. This treatment removes calcium, magnesium, sodium, potassium, aluminum, and iron atoms or ions from the framework while leaving the silicon framework intact as confirmed via X-ray fluorescence and diffraction. SEM images on calcined and HCl treated NV-Na were obtained. BET surface area analysis confirmed an increase in surface area for the two zeolites after treatment, NM-Ca (20.0(1) to 111(4) m2/g) and NV-Na (19.0(4) to 158(7) m2/g). 29Si and 27Al MAS NMR were performed on the natural and treated NV-Na zeolite and the data for the natural NV-Na zeolite suggested a Si:Al ratio of 4.33 similar to that determined by X-Ray fluorescence of 4.55. Removal of lead ions from solution decreased from the native (NM-Ca, 0.27(14), NV-Na, 1.50(17) meq/g) compared to the modified zeolites (30 min HCl treated NM-Ca 0.06(9) and NV-Na, 0.41(23) meq/g) and also decreased upon K+ ion pretreatment in the HCl modified zeolites.

Soil washing is a rapid and efficient method for heavy metals removal. In this study, in order to prove the feasibility of leaching remediation technology for remediation of lead-contaminated soil around a smelter, intermittent oscillating washing tests and extensive continuous tests were conducted to remediate Pb contaminated soils. Plant growth tests with wheat (Bainong Aikang 58) were also conducted to investigate the effects of leaching on plant growth and the Pb content of stems and leaves. The results revealed that in soils, Pb mainly exists in the forms of PbCO3, Pb5(PO4)3Cl2, PbSO4, and in small amounts of PbS. The intermittent oscillating washing tests showed that a lower liquidsolid(L/S) ratio and a higher leaching temperature and time were related to increased Pb removal efficiency. The Pb removal efficiency rates in the oscillating washing tests and the extensive continuous tests were 72.50% and 69.94%, respectively. In addition, the chemical and physical characteristics of the soil were basically unchanged after the leaching regimes. The results of the plant growth tests showed that the leaching regimes did not have a negative effect on the survival rate and growth of the wheat, and the heavy metal contents of the stem and leaf were effectively reduced. This study provides a reference for the large-scale remediation of contaminated soils.

Solid-state batteries (SSBs) have emerged as a promising alternative to conventional lithium-ion batteries, with notable advantages in safety, energy density, and longevity, yet the environmental implications of their lifecycle, from manufacturing to disposal, remain a critical concern. This review paper examines the environmental impacts associated with the production, use, and end-of-life management of SSBs, starting with the extraction and processing of raw materials which highlights significant natural resource consumption, energy use, and emissions. A comparative analysis with traditional battery manufacturing underscores the environmental hazards of novel materials specific to SSBs. The review also assesses the operational environmental impact of SSBs by evaluating their energy efficiency and carbon footprint in comparison to conventional batteries, followed by an exploration of end-of-life challenges including disposal risks, regulatory frameworks, and the shortcomings of existing waste management practices. A significant focus is placed on recycling and reuse strategies, reviewing current methodologies like mechanical, pyrometallurgical, and hydrometallurgical processes, along with emerging technologies that aim to overcome recycling barriers, while also analyzing the economic and technological challenges of these processes. Additionally, real-world case studies are presented, serving as benchmarks for best practices and highlighting lessons learned in the field. In conclusion, the paper identifies research gaps and future directions for reducing the environmental footprint of SSBs, underscoring the need for interdisciplinary collaboration to advance sustainable SSB technologies and contribute to balancing technological advancements with environmental stewardship, thereby supporting the transition to a more sustainable energy future.

The emphasis in the automotive industry towards sustainable mobility has led to a significant interest in hybrid-electric propulsion systems with high energy density batteries. Addressing the needs of this strategy, the battery market is exploring new technologies to improve the safety and lifespan of electric vehicles. To this end, there is a focus on the all-solid-state battery (ASSB) technology for its cycle capabilities. Filling the current void in the literature pertaining to accurate ageing models for ASSBs, in this work, we present an enhanced version of the numerical ageing model, originally developed for liquid electrolyte based batteries, to forecast the development of the solid electrolyte interface layer that is the major cause of battery capacity fading. The model has been tested on prototype batteries and reveals an accuracy of 99%. The capacity fade in ASSBs has been investigated under different conditions, and the enhanced ageing model has been validated using experimental data from these batteries. The findings suggest that there is potential for solid-state batteries to be commercialized, although significant work is needed to match the manufacturing level of lithium-ion batteries with liquid electrolytes.

Three-dimensional V₂O₅ hollow structures have been prepared through a simple synthesis strategy combining solvothermal treatment and a subsequent thermal annealing. The V₂O₅ materials are composed of microspheres 2–3 μm in diameter and with a distinct hollow interior. The as-synthesized V₂O₅ hollow microspheres, when evaluated as a cathode material for lithium-ion batteries, can deliver a specific capacity as high as 273 mAh·g⁻¹ at 0.2 C. Benefiting from the hollow structures that afford fast electrolyte transport and volume accommodation, the V₂O₅ cathode also exhibits a superior rate capability and excellent cycling stability. The good Li-ion storage performance demonstrates the great potential of this unique V₂O₅ hollow material as a high-performance cathode for lithium-ion batteries.

This paper presents an optimized energy management strategy for Li-ion power batteries used on electric vehicles (EVs) at low temperatures. Under low-temperature environments, EVs suffer a sharp driving range loss resulted from the energy and power capability reduction of the battery. Simultaneously, because of Li plating, battery degradation becomes an increasing concern as temperature drops. All these factors could greatly increase the total vehicle operation cost. Prior to battery charging and vehicle operating, preheating battery to a battery-friendly temperature is an approach to promote energy utilization and reduce total cost. Based on the proposed LiFePO4 battery model, the total vehicle operation cost under certain driving cycles is quantified in the present paper. Then given a certain ambient temperature, a target temperature of preheating is optimized under the principle of minimizing total cost. As for the preheating method, a liquid heating system is also implemented on an electric bus. Simulation results show that the preheating process becomes increasingly necessary with a decreasing ambient temperature; however, the preheating demand declines as driving range grows. Vehicle tests verify that the preheating management strategy proposed in this paper is able to save total vehicle operation cost.

Novel collector lead(II)-benzohydroxamic acid (Pb(II)-BHA) complexes in aqueous solution were characterized by using experimental approaches, including Ultraviolet-visible (UV-Vis) spectroscopy and electrospray ionization–mass spectrometry (ESI-MS), as well as first-principle density functional theory (DFT) calculations with consideration for solvation effects. The Job plot delineated that a single coordinated Pb(BHA)⁺ should be formed first, and the higher coordination number complexes can be formed subsequently. Moreover, the Pb(II)-BHA species can aggregate with each other to form complicated structures, such as Pb(BHA)₂ or highly complicated complexes. ESI-MS results validated the existence of Pb-(BHA)_n=1,2 under different solution pH values. Further, the first-principles calculations suggested that Pb(BHA)⁺ should be the most stable structure, and the Pb atom in Pb(BHA)⁺ will act as an active site to attack nucleophiles. These findings are meaningful to further illustrate the adsorption mechanism of Pb(II)-BHA complexes in mineral processing.

A low-cost bio-mass-derived carbon substrate has been employed to synthesize MoS₂@carbon composites through a hydrothermal method. Carbon fibers derived from natural cotton provide a three-dimensional and open framework for the uniform growth of MoS₂ nanosheets, thus constructing hierarchically coaxial architecture. The unique structure could synergistically benefit fast Li-ion and electron transport from the conductive carbon scaffold and porous MoS₂ nanostructures. As a result, the MoS₂@carbon composites, when served as anodes for Li-ion batteries, exhibit a high reversible specific capacity of 820 mAh g^-1, high-rate capability (457 mAh g^-1 at 2 A g^-1), and excellent cycling stability. The superior electrochemical performance makes the MoS₂@carbon composites to be low-cost and promising anode materials for Li-ion batteries.

The ceramic sherds from approximately 20 samples of lead-glazed tableware, recovered from diverse archaeological sites, including three repurposed storage pits transformed into dumpsters within the medieval city of Santarém (13th-14th century), underwent a meticulous examination. This investigation utilized techniques such as micro-Raman, ground state diffuse reflectance absorption, and X-ray fluorescence spectroscopies, in addition to X-ray diffraction and stereomicroscopy. A parallel study was conducted on contemporaneous European ceramics (glazed sherds) sourced from archaeological sites dating back to the 13th-15th centuries in Saintonge (France), Ardenne, Zomergem, and Bruges (Belgium), as well as Surrey-Hampshire, Kingston, and Cheam (England). The colour of the ceramic bodies is predominantly white or whitish, with a few exhibiting a vivid red hue. Ceramic sherds with a light paste composition were likely crafted using kaolin clays as raw materials. Analyses of fabric, mineralogical, and elemental composition of the sherds suggest that the majority of Santarém's glazed ceramics were locally or regionally produced, potentially derived from a Pliocene kaolin-rich sand formation. However, this conclusion is not supported by the absence of discovered lead glaze kilns or workshops in Santarém for the late Middle Ages. A distinctive feature from the European workshop ceramics lies in the quartz temper content and fabric.

Quasi-solid composited electrolytes were produced by LiFSI initiated polymerized poly-(Dioxolane) (PDOL) with garnet-LLZO (Li7La2Zr3O12) nanofibers and used in lithium-metal batteries. Linear sweep voltammetry shows that the initial oxidation voltage of 4.6 V for Gel-10% (G10, 10% wt. LLZO in PDOL) vs Li/Li+. EIS test of stainless steel// stainless steel symmetric cells for Gel-1% (G1), Gel-5% (G5) and Gel-10% (G10) show ion conductivity (5*10-5 S/cm). Li/G10/Li symmetric cells have stable stripping-plating cycling performance over 1300 hours continuously with the current density of 0.1 mA/cm2 at 25 oC, indicating a good interface contact and stable lithium-ion transport pathway through the composite electrolytes. LFP/G10/Li batteries have stable charge-discharge plateau, low polarization voltage of 0.07-volt, energy efficiency of 95% and coulombic efficiency of ~99% at current density of 26.3 mA/g at 25 oC for over 100 cycles.

This study presents the synthesis and electrochemical evaluation of nitrogen-doped vanadium oxide (N-V2O3/C) as a cathode material for aqueous zinc-ion batteries (AZIBs), using a hydrothermal method. Compared to undoped V2O3/C, N-V2O3/C exhibits enhanced electrical conductivity, capacity, and electrochemical kinetics, attributed to the incorporation of pyridinic and pyrrolic nitrogen. Initial charge-discharge cycles indicate phase transitions to amorphous vanadium oxides, enhancing conductivity. N-V2O3/C shows a high specific capacity of 168.4 mAh g−1 at 10 A g−1 and remarkable reversibility, highlighted by the transient existence of intermediate species during cycling. Optimal electrochemical performance is achieved with a vanadium to nitrogen molar ratio of 2:3, indicating the significant impact of nitrogen doping concentration on the material’s efficiency. This work underscores the potential of N-V2O3/C as a superior cathode material for AZIBs.

Small and Medium Enterprises (SMEs) are recognized as the main drivers of economic growth and development in many countries throughout the world. SMEs represent about 90% of the manufacturing sector and contribute about 14% of the total manufacturing contribution to GDP. Despite SMEs’ potential to change Nigeria’s status from a consumer economy to a production economy, policies that will ensure that environmentally- friendly manufacturing processes and production technology are not implemented or complied with. SMEs’ operational activities may be deleterious to human health and the ecosystem if environmental management practices are not adopted or prioritized. This paper evaluated the perception and adoption of the Environmental Management System, mainly ISO 14001, by SMEs in Nigeria. One hundred and fifty (150) SMEs in the manufacturing sector in Lagos and Ogun State, Southwestern Nigeria, were randomly selected for this study. The paper posits that environmental management literacy and advocacy should be carried out in SMEs. Environmental management practices involve engaging both industries and product end-users in sustainable practices. The paper concludes that the implementation of environmental management practices and culture by SMEs will abate environmental pollution and its concomitant health risks to humans, the environment, flora, and fauna. Mandatory and voluntary environmental measures are suggested as a means of engendering eco-friendly innovation for sustainable development, triggering employment, job security, and gross domestic product.

In this work, we synthesized chitosan grafted-poly acrylic acid (CS-g-PA) through surface-initiated atom transfer radical polymerization (SI-ATRP). We also studied the adsorption process of copper and lead ions onto CS-g-PA surface. Adsorption equilibrium studies indicated pH 4.0 as the best pH for the adsorption process, while the maximum adsorption capacity for Pb2+ ions was 98 mg*g-1 and for Cu2+ was 164 mg*g-1, higher adsorption capacities than chitosan alone (CS), where Pb2+ was only 14.8 mg*g-1and Cu2+ was 140 mg*g-1, respectively. Furthermore, the adsorption studies indicated that Langmuir model describes all the experimental data. All these results suggest that the new CS-g-PA polymers had potential as adsorbent for hazardous and toxic metal ions produced by different industries.

This investigation explores the potential of enhancing aqueous zinc-ion batteries (AZIBs) through the introduction of a novel cathode material, NH4V4O10 (NVO), combined with reduced graphene oxide (rGO). Utilizing Density Functional Theory (DFT), it was hypothesized that the incorpora-tion of rGO would increase the interlayer spacing of NVO and diminish the charge transfer in-teractions, thus promoting enhanced diffusion of Zn2+ ions. These theoretical predictions were substantiated by experimental data acquired from hydrothermal synthesis, which indicated a marked increase in interlayer spacing. Significantly, the NVO-rGO composite exhibits remarkable cyclic durability, maintaining 95% of its initial specific capacity of 507 mAh g−1 after 600 cycles at a current density of 5 A g−1. The electrochemical performance of NVO-rGO not only surpasses that of pristine NVO but also outperforms the majority of existing vanadium oxide cathode materials reported in the literature. This study underscores the effective integration of theoretical insights and experimental validation, contributing to the advancement of high-performance energy storage technologies.

Lead optimization in drug discovery is a crucial phase where initial hits are refined into compounds with improved pharmacological properties. While traditional methods rely on manual experimentation and modifications, AI-driven techniques have revolutionized this process by leveraging big data and predictive modeling. This review explores how AI-driven approaches accelerate lead optimization, showcasing examples like deep neural networks and reinforcement learning. Integration of multi-omic data and experimental validation further enhances AI-driven strategies. The future lies in refining these AI methods, democratizing tools, and interdisciplinary collaboration to streamline drug discovery and address medical needs efficiently.

The objective of this study was to investigate the concentration and spatial distribution patterns of six potentially toxic heavy metal elements (Mn, Zn, Cr, Pb, Cu and Ni) in bus station dusts in the Xifeng district of Gansu province, NW China. The contents were analyzed for Mn, Zn, Cr, Pb, Cu and Ni by using S8 TIGER Brochures wavelength dispersive X-ray fluorescence spectrometry. Geoaccumulation index (Igeo ), enrichment factor (EF), pollution index (PI) and integrated pollution index(IPI) were calculated to evaluate the heavy metal contamination level of bus station dusts. The results indicate that, in comparison with the background values of local soil, bus station dusts in Xifeng have elevated metal concentrations as a whole. The concentrations of heavy metals investigated in this paper are compared with the reported data of other cities. The results show that the arithmetic means of Mn, Zn, Cr, Pb, Cu and Ni are 440.8, 137.9, 60.0, 42.8, 33.5 and 19.8mg kg−1 respectively. The mean values of Igeo reveal the order of Ni<Mn<Cr<Cu<Zn<Pb. The high Igeo and EF for Cu, Zn and Pb in bus station dusts indicate that there is a considerable Cu, Zn and Pb pollution, which mainly originate from traffic and industry activities. The Igeo and EF of Ni, Mn and Cr are low and the assessment results indicate an absence of distinct Ni, Mn and Cr pollution in bus station dusts. The assessment results of PI also support Cu, Zn and Pb in bus station dusts presented middle pollution, and IPI indicates heavy metals of bus station dusts polluted seriously.

This study explores the enhancement of aqueous zinc-ion batteries (AZIBs) using ammonium-enhanced vanadium oxide cathodes. Density Functional Theory (DFT) calculations reveal that NH₄⁺ incorporation into V₆O₁₆ lattices significantly facilitates Zn²⁺ ion diffusion by reducing electrostatic interactions, acting as a structural lubricant. Subsequent experimental validation using (NH₄)₂V₆O₁₆ cathodes synthesized via a hydrothermal method corroborates the DFT findings, demonstrating remarkable electrochemical stability with a capacity retention of 90% after 2000 cycles at 5 A g⁻¹. These results underscore the potential of NH₄⁺ in improving the performance and longevity of AZIBs, providing a pathway for sustainable energy storage solutions.

Perovskite solar cells (PSCs) are vital for their optical and electrical properties, with lead-based PSCs reaching a remarkable efficiency of 26.1%, while tin-based counterparts achieve 18.71%. Due to lead's toxicity, there's a push for alternatives like tin. However, tin-based PSCs suffer from stability issues and high defect density states, necessitating the development of cost-effective, high-performance, and eco-friendly alternatives. In this study, we designed a hetero-junction architecture using MASnI3-based Perovskite, opti-mized with SCAPs-1D. After exhaustive analysis, our device achieved a power conversion efficiency of 24.18%, with enhanced parameters including Voc of 0.09323V, Jsc of 30.8360 mA/cm2, and FF of 84.10%. Recombination rates, particularly Shockley-Read Hall recom-bination, were significantly reduced. Parametric analyses, encompassing absorber layer thickness, band gap, defect density, doping concentration, and operating temperature, in-dicate potential efficiency enhancements. This underscores the viability of Sn-based PSCs as a cost-effective, efficient, and environmentally benevolent alternative to lead-based counterparts, promising advancements in future research and development efforts.

Drosophila melanogaster serves as a important research model both for genetic investigations and for the study of metal toxicity, facilitating the elucidation of physiological mechanisms comparable to those of human organisms. In our research, we evaluated the toxicity effect resulting from exposure to various concentrations of lead and copper on the prolificity rates throughout the life cycle (egg-adult) of four genotypes of Drosophila melanogaster: wild-type (control), white, brown, and white-vestigial. During our study, the prolificity rates were examined across three repetitions under the impact of exposure to concentrations of 0.50, 1.00, 2.00, and 4.00 mM of copper (CuSO₄) and lead (Pb(C₂H₃O₂₎₂). Prolificity rates throughout the life cycle exhibited variations as a direct consequence of genetic factors, the concentration of exposure, and the specific type of metal, either copper or lead. The mutant white-vestigial genotype revealed an IC₅₀ concentration for prolificity inhibition at lower doses of 2.00 mM for copper and 4.00 mM for lead, in contrast to the control genotype (wild-type), which exhibited an inhibition concentration rate >IC₅₀ of 4.00 mM only in the case of copper. Our results concluded that the (i) dose influences the prolificity rate in a directly proportional manner, (ii) comparative analyses between copper and lead revealed that copper displayed toxicity across all genotypes within the concentration range of 0.50 mM to 2.00 mM. In contrast, lead exhibited toxicity within the concentration range of 1.00 mM to 4.00 mM, highlighting a (iii) more acute toxicity characteristic in the case of copper. Thus, the results of this research reflect the importance of using Drosophila melanogaster as a genetic model in the comparative study of the interaction between genetic factors and the toxicity of metals, offering significant insights into monitoring their impact and defining the maximum permissible doses on organisms.

The ever-rising demands for energy dense electrochemical storage systems have been driving interests in beyond Li-ion batteries such as those based on lithium and magnesium metals. These high energy density batteries suffer from several challenges, several of which stem from the flammability/volatility of the electrolytes and/or instability of the electrolyte with either the negative, positive electrode or both. Recently, hydride-based electrolytes have been paving a path towards overcoming these issues. Namely, highly performing solid state electrolytes have been reported and several key challenges in multivalent batteries were overcome. In this review, the classes of hydride-based electrolytes reported for energy dense batteries are discussed. Future perspectives are presented to guide research directions in this field.

Reduced-order electrothermal models play a key role in the design and control of lithium- ion cell stacks, calling for accurate model parameter calibration. This paper presents a complete electrical and thermal experimental characterization procedure for coupled modeling of cylindrical lithium-ion cells in order to implement them in a prototype Formula SAE hybrid racing car. The main 4goal of the tests is to determine cell capacity variations with temperatures and discharge currents, to predict the open circuit voltage of the cell and its entropic component. A simple approach for the characterization of the battery equivalent electrical circuit and a two-steps thermal characterization method are also shown. The investigations are carried out on four commercial 18650 NMC lithium cells. The model demonstrated to predict the battery voltage at a RMS error lower than 20mV and the temperature to a RMS error equal to 0.5 ◦C. The authors hope that this manuscript can contribute to the development of standardized characterization techniques for such cells, while offering experimental data and validated models that can be used by researchers and BMS designers in different applications.

The transportation sector significantly contributes to greenhouse gas emissions, thus imposing sig-nificant environmental hazards. In response, many nations have begun promoting Electric Vehicles (EVs) as an ecologically sustainable substitute for traditional combustion vehicles. Lithium-Ion Batteries (LIBs), characterized by their high energy density, extended lifespan, and relatively low self-discharge rate, have become the suitable energy storage system for EVs, advancing the field of sustainable transportation. The decreasing cost of LIB production has primarily driven this progression, realized through a combination of economies of scale, advancements in electrode materials and cell design, and re-finements in manufacturing processes. All these elements collectively contribute to the cost reduc-tion of LIBs. A foreseeable implication of this trend is an expected surge in LIBs that will exhaust their operational lifespan and, consequently, be cast away into the environment. One mitigating strategy for this impending environmental issue involves collecting these spent EV batteries, re-configuring them, and repurposing them for applications with less rigorous weight, performance, and size prerequisites. This approach would not only prolong the utility life of the batteries but also ameliorate their environmental impacts. Nevertheless, second-life batteries are anticipated to exhibit a higher rate of gas evolution, necessitating comprehensive testing and readjustments to ensure safe operation in secondary ap-plications. The regulatory framework encompassing the second-life battery sector still needs to be defined regarding norms, technical standards, and legislation. This paper aims to elucidate the primary regulations and technical standards proposed thus far in the second-life battery marketplace. The results underscore the exigency for neutral evaluative entities, such as universities, research centers, and governmental institutions, to perform an unbi-ased assessment of the second-life battery market. This would pave the way for novel technical standards and legislative measures specifically tailored to this emerging sector.

Acetic acid bacteria (AAB) are major contributors to the production of fermented vinegar, offering various cultural, culinary, and health benefits. Although the residual unpasteurized AAB after vinegar production are not pathogens, these are necessary the safety evaluations including antibiotic resistance for the use as starters. In this research, we investigated the antibiotics resistance profiles of 26 AAB strains, including various species of Komagataeibacter and Acetobacter, against ten different antibiotics using the E-test method. All strains exhibited resistance to aztreonam and clindamycin. Komagataeibacter species demonstrated a 50% resistance rate to ciprofloxacin, analogous to Acetobacter species, but showed twice the resistance rates to chloramphenicol and erythromycin. Genomic analysis of K. saccharivorans CV1 identified intrinsic resistance mechanisms, such as multidrug efflux pumps, thereby enhancing our understanding of antibiotic resistance in acetic acid-producing bacteria. These findings enhance understanding of antibiotic resistance in AAB for food safety and new antimicrobial strategies, suggesting the need for standardized testing methods and molecular genetic study.

Studies suggest that elevated postnatal blood lead levels (BLLs) are negatively associated with child growth. This study aimed to investigate associations of childhood BLLs at age one-year and growth outcomes at age six-years (n=661) in a cohort of children in Allada, Benin. The growth outcomes studied are weight-for-age Z-score (WAZ), height-for-age Z-score (HAZ) and BMI-for-age Z-score (BMIZ), head circumference (HC), underweight, stunting, and wasting. Multivariable regression models examined associations between blood lead levels, growth outcomes with adjustment for potential confounders. The geometric mean BLLs was 59.3 μg/L and 82% of children had BLLs &gt;35 μg/L at one year. After adjusting for confounding factors, no association was found between BLLs quartiles and HAZ, WAZ, BMIZ, and height and weight growth velocities. However, boys in the highest quartile had 1.02 cm lower HC (95% CI: [-1.81, -0. 24]) as compared to those in the lowest quartile with a dose-response trend across quartiles (Ptrend =0.02). Furthermore, an increased risk of being stunted was observed in children in the highest quartile of exposure compared to the first (OR: 2.43; 95% CI: [1.11 – 5.33]) with a dose-response trend (Ptrend =0.03). Blood lead was found to be associated with an increased risk of childhood stunting and lower head circumference in a resource-limited setting.

Fine dust causes various disorders, including cardiovascular, neurological, renal, reproductive, motor, systemic, respiratory, and cancerous diseases. Therefore, it is necessary to study functional materials to prevent these problems. In this study we used various methods, including quantitative PCR, flow cytometry, ELISA, and Alizarin O staining, to study the beneficial effects of erucic acid against fine dust. Erucic acid and erucic acid-induced exosomes (EIE) strongly suppress the attenuation of osteocytic differentiation and inflammation induced by fine dust. Erucic acid effectively suppresses inflammation in fibroblasts exposed to fine dust. Notably, despite exposure to fine dust, EIE promoted osteocytic differentiation in adipose-derived stem cells (ASC) and osteogenesis in macrophages, in addition to phagocytosis. Dramatic upregulation of RunX2 and BMP7 by EIE indicates that it is a strong activator of osteocytic differentiation in ASC and protects them from the effects of fine dust. Moreover, EIE induces immune activity and acts as an osteogenic trigger for macrophages. Therefore, this study suggests the potential use of erucic acid and erucic acid-induced exosomes (EIE) as biomaterials to prevent environment-borne diseases.

In the brain, astrocytes regulate shape and functions of the synaptic and vascular compartments through a variety of released factors and membrane-bound proteins. An imbalanced astrocyte activity can therefore have drastic negative impacts on brain development, leading to the onset of severe pathologies. Clinical and pre-clinical studies show alterations in astrocyte cell number, morphology, molecular makeup and astrocyte-dependent processes in different affected brain regions in neurodevelopmental (ND) and neuropsychiatric (NP) disorders. Astrocytes proliferate, differentiate and mature during the critical period of early postnatal brain development, a time window of elevated glia-dependent regulation of a proper balance between synapse formation/elimination, which is pivotal in refining synaptic connectivity. Therefore, any intrinsic and/or extrinsic factors altering these processes during the critical period may result in an aberrant synaptic remodelling and onset of mental disorders. The peculiar bridging position of astrocytes between synaptic and vascular compartments further allows them to “compute” the brain state and consequently secrete factors in the bloodstream, which may serve as diagnostic biomarkers of distinct healthy or disease conditions.Here, we collect recent advancements regarding astrogenesis and astrocyte-mediated regulation of neuronal network remodelling during early postnatal critical periods of brain development, focusing on synapse elimination. We then propose alternative hypotheses for an involvement of aberrancies in these processes in the onset of ND and NP disorders. In light of the well-known differential prevalence of certain brain disorders between males and females, we also discuss putative sex-dependent influences on these neurodevelopmental events.From a translational perspective, understanding age- and sex-dependent astrocyte-specific molecular and functional changes may help to identify biomarkers of distinct cellular (dys)functions in health and disease, favouring the development of diagnostic tools or the selection of tailored treatment options for male/female patients.

Salmonella infections can lead to intestinal inflammation and metabolic disorders in birds. However, whether ARA metabolism is involved in Salmonella-induced intestinal inflammation remains unclear. This experiment investigated the changes in cecal flora and arachidonic acid (ARA) metabolism in Hainan Wenchang chickens infected with S. Typhimurium using 16s rDNA sequencing and targeted metabolomics. The results showed that the levels of ARA metabolites were increased in the cecum tissue of Wenchang chickens after infection with S. Typhimurium, including prostaglandin E2, prostaglandin F2α, lipoxin A4, ±8(9)-EET, ±11(12)-EET, and ±8,9-DiHETrE. The content of key enzymes for ARA production and metabolism (PLA2 and COX-2) in chicken cecum tissues was increased after S. Typhimurium infection. The relative mRNA levels of inflammatory factors were also increased after infection, including IFN-γ, TGF-β1, IL-4, and IL-6. In HD11 cells, the use of a cyclooxygenase (COX) inhibitor reduced the increased levels of COX-2 and PGF2α induced by S. Typhimurium infection and effectively reduced the inflammatory response. In addition, the number of beneficial genera (e.g., Bifidobacterium, Lactobacillus, and Odorobacterium) in the cecum of Wenchang chickens was significantly reduced after infection with S. Typhimurium. In this study, we revealed the structure of the cecal flora of Wenchang chickens infected with S. Typhimurium and demonstrated that S. Typhimurium can mediate the onset and development of intestinal inflammation through the activation of the metabolic pathway of ARA cyclooxygenase in Wenchang chickens. The results can provide data support and theoretical support for the prevention and control of avian salmonellosis.

A decanter centrifuge has been employed to successfully separated phosphoric acid and rare-earth-element (REE)-containing particles from phosphoric acid sludge with concentrations ranging from 1,000 to 2,200 ppm REEs. Operating efficiently with up to 35 wt.% solids, the centrifuge was demonstrated to achieve approximately 95% phosphoric acid recovery and 90% REEs recovery in a single pass, eliminating the need for additional processing steps. This breakthrough supports a proposed REEs oxide recovery process integrating phosphoric acid (PA), elemental phosphorus (P4), and REEs into two potential pathways: PA-REO and PA-P4-REO. These processes aim to reintroduce recovered phosphoric acid into the main product to significantly increase output and revenue. Post-separation, phosphorus-rich particles can be converted to P4, while REEs-containing solids undergo further treatment including acid leaching, extraction/stripping, precipitation, and calcination to produce a marketable rare-earth oxide (REO) material. Techno-economic analysis indicates promising profitability, with the PA-REO process showing a delta net present value (∆NPV) of $441.8 million and an expected return within a year of construction, while the PA-P4-REO process yields a ∆NPV of $178.7 million over a 12-year return period. Both pathways offer robust financial prospects and demonstrate the feasibility of commercial-scale REEs recovery from phosphoric acid sludge.

In this paper, we consider a make-to-order supply chain which satisfies demand that is dependent on both price and quoted lead -time. The manufacturer chooses the lead -time and the order quantity, and the retailer sets the revenue shares. The interactions between the manufacturer and the retailer are modelled as a Nash Game, and the existence and uniqueness of pure strategy equilibrium are demonstrated. A mechanism that enables the supply chain to coordinate the decisions of the members is developed. Lastly, we also analyze how the supply chain system parameters impact the optimal supply chain decisions and the supply chain performance.

Saikosaponin (SS) a is a compound with various pharmacological properties and easily degraded into SSb1 and SSg in acid condition. In present work another two new degradation products of SSa formed under acid hydrolytic condition were detected and isolated by analytical and semi-preparative liquid chromatography technology, furthermore their structures were characterized as hydroxyl-saikosaponin a and SSb2 by spectral analysis, which is not only essential in stability-indicating method development and validation but also could be used as a worst case to assess the analytical method performance of SSa. Moreover their structural transformation pathways were also proposed.

Plant activators have emerged as promising alternatives to conventional pesticides for crop disease manage-ment due to their unique mode of action. By priming the plant's innate immune system, these compounds can induce systemic acquired resistance against a broad spectrum of pathogens without directly inhibiting their proliferation. Key advantages of plant activators include prolonged defense activity, lower effective dosages, and negligible risk of developing pathogen resistance. Among the various defensive pathways tar-geted, the salicylic acid (SA) signaling cascade has been extensively explored, leading to the successful devel-opment of commercial activators like benzothiadiazole for widespread application in crop protection. While the action sites of many SA-targeting activators have been preliminarily mapped to different steps along the pathway, a comprehensive understanding of their precise mechanisms remains elusive. This review provides a historical perspective on plant activator development and outlines diverse screening strategies employed across multiple levels, from whole-plant bioassays to molecular and transgenic approaches. We expound on the intricate components, biological relevance, and regulatory circuits governing the SA pathway, while criti-cally examining the structural features, bioactivities, and proposed modes of action of classical activators such as benzothiadiazole derivatives, salicylic acid analogs, and other small molecules. Insights from field trials as-sessing their practical applicability are also discussed. Furthermore, we highlight the current status, challenges, and future prospects in the realm of SA-targeting activator development globally, with a focus on recent en-deavors in China. Collectively, this comprehensive review aims to synthesize existing knowledge and provide a roadmap for future research toward developing more potent and mechanistically understood plant activa-tors that fortify crop immunity against disease.

Lithium-ion (Li-ion) batteries are becoming more common in portable electronic devices due to their high energy density, lack of memory effect, and high charge and discharge rate capabilities. Li-ion batteries are a relatively new technology, first marketed in the early 1990s, and research and development work are ongoing to improve safety and increase capacity, charge/discharge rate, and lifetime [1]. In this paper, we review the types and characteristics of Li-ion batteries and summarize charging methods and safety considerations. Following, we design and fabricate Li-ion battery and highlight the steps of fabrication that ensure fast charge/discharge rates that give the battery more reliability and high energy density

Elevated serum uric acid (sUA) is associated with risk of developing cardiovascular disease (CVD). Here, we examined the prognostic significance of sUA and exercise capacity in 411 Japanese adults (age, ≥65; mean, 81 years) hospitalized for worsening CVD. Mean sUA was significantly higher in the 23% of patients on an sUA-lowering agent than in those not. When the patients were stratified by sUA into three groups (7.0 mg/dL), the high sUA group had significantly worse peak VO2 and composite endpoint (rehospitalization due to worsening CVD and all-cause mortality) compared with low and moderate sUA groups (P < 0.001). When the patients were stratified by sUA into five groups (sUA 10.0 mg/dL), the incidence of the composite endpoint was significantly higher in the highest sUA group compared with that in the reference group, but only in women. Univariate Cox regression analysis, but not a multivariate analysis, indicated that sUA was significantly associated with the composite endpoint. Although sUA and exercise capacity may have some degree of prognostic significance in older patients with CVD, this significance may differ between men and women.

To date, zinc ion batteries (ZIBs) have been attracting extensive attention due to their outstanding properties and the potential to be the solution for next-generation energy storage systems. However, the uncontrollable growth of zinc dendrites and water-splitting issues seriously restrict the further scalable application. Over the past few years, solid polymer electrolytes (SPEs) have been regarded as a promising alternative to address these challenges and facilitate the practical advancement of zinc batteries. In this review, we revisited the research progress of SPEs applied in zinc batteries in the past few years and focus on introducing cutting-edge polymer science and technologies that can be utilized to prepare advanced SPEs for high-performance zinc batteries. The operating mechanism of SPEs and the functions of polymers will be summarized. To highlight the polymer functions, SPEs are categorized into three types, respectively, homogenous polymer SPEs, hybrids polymer SPEs, and nanocomposites SPEs, which are expected to reveal the roles and principles of various polymers in zinc batteries. This review presents the current research progress and fundamental mechanisms of polymer-based SPEs in zinc batteries, outlines the challenging issues encountered, and meanwhile proposes potential solutions for future endeavours.

The superfamily of Acid proteases has two catalytic aspartates for proteolysis of their peptide substrates. Here, we show a minimal structural scaffold, the Structural Catalytic Core (SCC), which packs all conserved substructure elements around the catalytic machinery, and which can be found in all enzymes of the Acid proteases superfamily. The SCC is a dimer of several structural blocks, such as the DD-link, the D-loop and the G-loop, around two catalytic aspartates in each protease subunit or within an individual chain. The dimer of two D-loop/DD-link substructures makes a DD-zone, and the dimer of two D-loop/G-loop substructures makes a psi-loop. These structural markers are useful for protein comparison, structure identification, protein family separation and protein engineering.

Button batteries pose a significant threat to young children and are found in many household items and children’s toys. Along with product manufacturers and retailers, parents and caregivers have a role in button battery ingestion prevention through vigilance regarding items containing button batteries in the home, and knowledge of button battery ingestion symptoms. There is limited information available about parent and caregiver perspectives towards button battery safety. Identifying the areas where increased education is required is important for informing safety campaigns and delivering targeted education. This study aimed to examine parent and caregiver elemental perspectives on button battery safety. One hundred and seventy-four parents and caregivers of children aged 0 to 5 completed a cross-sectional online survey. Distribution occurred via social media. The survey contained multiple-choice questions pertaining to button battery perspectives, and one open-ended question. Respondents recognized the dangers of button battery ingestion, yet only 37% reported being familiar with button battery ingestion symptoms. While 68% knew of household items containing button batteries, only 21% were aware of product recall information sources. Approximately 64% understood immediate post-ingestion steps and 17% found current safety labels unsatisfactory. In an open-ended question, parents and caregivers provided comments about button battery safety that revealed five broad themes; supervision and education; safe storage of button batteries in the home; ensuring children cannot access button batteries; disposing of button batteries safely; and avoiding purchasing items containing button batteries. This study provides a foundation for ongoing investigation of parent and caregiver perspectives on button battery home safety.

To better understand the shape memory materials and self-healing materials, a new series of liquid-crystalline shape memory polyurethane (LC-SMPU) composites, named SMPU-OOBAm, were successfully prepared by incorporating 4-octyldecyloxybenzoic acid (OOBA) into the PEG-based SMPU. The effect of OOBA on the structure, morphology and properties has been carefully investigated. The results demonstrate that SMPU-OOBAm have liquid crystalline properties, triple-shape memory properties and self-healing properties. The incorporated OOBA promotes the crystallizability of both soft and hard segments of SMPU, and the crystallization rate of the hard segment of SMPU decreases when the OOBA-content increases. Additionally, the SMPU-OOBAm forms a two-phase separated structure (SMPU phase and OOBA phase), and it shows two-step modulus changes upon heating. Therefore, the SMPU-OOBAm shows triple-shape memory behavior, and the shape recovery ratio decreases with an increase in the OOBA content. Finally, SMPU-OOBAm shows self-healing properties. The new mechanism can be ascribed to the heating-induced “bleeding” of OOBA in the liquid crystalline state and the subsequent re-crystallization upon cooling. This successful combination of liquid crystalline properties, triple-shape memory properties and self-healing properties make the SMPU-OOBAm composites with many promise applications in smart optical devices, smart electronic devices and smart sensors.

To clarify effects of weathered coal humic acid on water-stable aggregates and pore characteristics of reclaimed cambisol, this research analyzed the evolution characteristics of soil aggregates and pores. Effects of different humic acid dosages (0, 1%, 3%, and 5% by weight) and application period (1 year, 2 years, and 3 years) on soil aggregates and organic carbon components in soil water-stable aggregates were investigated. The results showed that water-stable macroaggregates (&gt;0.25 mm) had the highest content in the first year; but in the third year, water-stable microaggregates (0.053–0.25 mm) had the highest content, and silt and clay (&lt;0.053 mm) were at a maximum. In the third year of 5% treatment, mean weight and geometric mean diameters were the largest, soil structure was the most stable, and TOC and water-stable microaggregates (0.053–0.25 mm) in soil had the highest proportions. For 5% treatment, the majority of irregular pores were independent in the first year, and number of pores decreased in the second year, but average pore volume increased, forming robust connected pores. In the third year, the number of elongated and irregular pores increased. In the third year of 5% treatment, most pores were irregular and of size &gt;100 μm, and soil structure was the most stable.

Background: Microscopic examination of acid-fast stained sputum smears for detecting mycobacterial acid-fast bacilli (AFB) remains the most economical and readily available method for laboratory diagnosis of tuberculosis (TB). However, this conventional approach has limitations, including low sensitivity and labor-intensive procedures. Methods: An automated microscopy system incorporating artificial intelligence (AI) and machine learning for AFB identification was evaluated. The study was conducted at an Infectious Disease Hospital in Jiangsu Province, China, utilizing an intelligent microscope system (TB-Scan, Wellgen Medical, Kaohsiung). A total of 1,000 sputum smears were included in the analysis, with the system capturing digital microscopic images and employing an image recognition model to automatically identify and classify AFB. Referee technicians provided the gold standard for discrepant results. Results: The automated system demonstrated an overall accuracy of 95.00% (950/1,000), sensitivity of 91.24% (177/194), and specificity of 95.91% (773/806). Notably, the system identified 21 smears as positive that were previously reported as negative, with referee technicians confirming 17 of these as true positive and retracting the test results accordingly. Recalculating the performance, the accuracy increased to 96.70% (967/1,000), sensitivity to 91.94% (194/211), and specificity to 97.97% (773/789), with a false negative rate of 8.06% (17/211) and a false positive rate of 2.03% (16/789). Conclusions: The incorporation of AI and machine learning into an automated microscopy system demonstrated the potential to enhance the sensitivity and efficiency of AFB detection in sputum smears compared to conventional manual microscopy. This approach holds promise for widespread application in TB diagnostics and potentially other fields requiring labor-intensive microscopic examination.

Graphene-based materials (GBMs) are a prospective material of choice for rechargeable battery electrodes because of their unique set of qualities, which include tunable interlayer channels, high specific surface area, and strong electrical conductivity characteristics. The market for commercial rechargeable batteries is now dominated by lithium-ion batteries (LIBs), however issues with organic electrolyte safety, high lithium pricing, and limited lithium resources have hindered LIB development. Zinc-based rechargeable batteries have emerged as a viable substitute for rechargeable batteries due to their affordability, safety, and improved performance. This review article explores recent developments in the synthesis and advancement of GBMs for rechargeable zinc‐air batteries (ZABs), and common graphene-based electrocatalyst types. An outlook on the difficulties and probable future paths of this extremely promising field of study is provided at the end.

Polyalcohol liquefaction can be done by acid or basic catalysis producing polyols with different properties. This study compared the mechanical properties of foams produced using polyols from liquefied Cytisus scoparius obtained by acid and basic catalysis and using two different foam catalysts. The differences were monitored using FTIR analysis. Acid-catalyzed liquefaction yielded 95.1 %, with the resultant polyol having an OH index of 1081 mg KOH/g while basic catalysis yielded 82.5 %, with a similar OH index of 1070 mg KOH/g. Generally, compressive strength with dibutyltin dilaurate (DBTDL) ranged from 16 - 31 kPa (acid-liquefied polyol) and 12 -21 kPa (base-liquefied polyol), while with stannous octoate (TIN), it ranged from 17 - 42 kPa (acid) and 29 - 68 kPa (base). Increasing water content generally decreased the compressive modulus and strength of foams. Higher water content led to a higher absorption at 1670 cm-1 in the FTIR spectrum due to the formation of urea. Higher isocyanate indices generally improved compressive strength, but high amounts led to unreacted isocyanate that could be seen by a higher absorption at 2265 cm-1 and 3290 cm-1. DBTL was shown to be the best foam catalyst due to higher trimer conversion seen in the spectra by a higher absorption at 1410 cm-1. Acid and base-derived polyols lead to different polyurethane foams with different FTIR spectra, particularly with a higher absorption at 1670 cm-1 for foams from acid-derived liquefaction.

The research was conducted in the Kırklareli stream, which flows southwest through the city of the same name toward the village of Kavaklı. The aim of the study is to evaluate water analysis results and assess the potential that the European Union drinking water standard for lead can be achieved in the Kırklareli stream by reliance on the low solubility of lead phosphate minerals. The present study used Visual MINTEQ 3.1 for all water chemistry simulations. The European Union drinking water standard for lead, which is 10 μg L⁻¹, is exceeded at least once and as many as three times at seven of the ten sites during the 2018 sampling season. Although the database solubility of hydroxypyromorphite is exceeded in most samples, it appears this may be the result of major ion substitutions in the hydroxypromorphite that forms in the Kırklareli stream which increases the effective solubility of lead in the stream.

The emergence of various electronic devices and equipment such as electric vehicles and drones requires higher energy density energy storage devices. Lithium-sulfur batteries (LSBs) are considered as the most promising new generation energy storage system owing to high theoretical specific capacity and energy density. However, the severe shuttle behaviors of soluble lithium polysulfides (LiPSs) and the slow redox kinetics lead to low sulfur utilization and poor cycling stability, which seriously hinder the commercial application of LSBs. Therefore, various catalytic materials have been employed to solve these troublesome problems. High entropy materials (HEMs), as advanced materials, can provide unique surface and electronic structures that expose plentiful catalytic active sites, which opens new ideas for the regulation of LiPSs redox kinetics. Notwithstanding many instructive reviews in the land of LSBs, while this review aims to offer a complete and shrewd summary of the current progresses in HEMs-based LSBs, including in-depth interpretation of design principles and mechanistic electrocatalysis functions as well as pragmatic perspectives.

Autism spectrum disorder (ASD) is a neurodevelopmental disorder characterized by impairments in social interaction and communication, anxiety, hyperactivity, and restricted interest for specific subjects. In addition to the genetic factors, multiple environmental factors have been related to the development of ASD. Animal models can serve as crucial tools for understanding the complexity of ASD and identifying potential therapeutic strategies. In this study, a chemical model of ASD has been developed in zebrafish by exposing embryos to valproic acid (VPA) from 4 to 48 hours post-fertilization. After the exposure, embryos were transferred to fish water and the effects on behavior and neurotransmitters profile were analyzed at both larval and adult stages. Larvae from VPA-treated embryos showed hyperactivity and decreased visual and vibrational escape responses, as well as an altered neurotransmitters profile, with increased glutamate and decreased acetylcholine and norepinephrine levels. Adults from VPA-treated embryos exhibited impaired social behavior characterized by larger shoal sizes and a decreased interest for their conspecifics. Neurotransmitter analysis revealed a significant decrease in dopamine and GABA levels in the brain. These results support the interest of this model in the study of ASD.

In this research, catalytic steam reforming acetic acid derived from the aqueous portion of bio-oil for hydrogen production was investigated by using different Ni/ATC (Attapulgite Clay) catalysts prepared by precipitation, impregnation and mechanical blending methods. The fresh and reduced catalysts were characterized by XRD, N₂ adsorption-desorption, TEM and H₂-TPR. The comprehensive results demonstrated that the interaction between active metallic Ni and ATC carrier was significantly improved in Ni/ATC catalyst prepared by precipitation method, and in which the mean Ni particle size was the smallest (~13 nm) resulted in the highest metal dispersion (7.5%). The catalytic performance of the three catalysts was evaluated through the process of steam reforming of acetic acid in a fixed-bed reactor under atmospheric pressure at two different temperatures, such as 550 ℃ and 650 ℃. Results showed that the Ni/ATC (PM-N/ATC) prepared by precipitation method, achieved the highest H₂ yield of ~82% and little lower acetic acid conversion efficiency of ~85% than that (~95%) of Ni/ATC (IM-NATC) prepared by impregnation method. In addition, the deactivation catalysts after reaction for 4 h were analyzed by XRD, TGA-DTG and TEM, which demonstrated that the catalyst deactivation was not caused by the amount of carbon deposition, but owed to the significant agglomeration and sintering of Ni particles in the carrier.

Inflammation is implicated in the etiology of obesity-related diseases. Thromboxane-prostanoid receptor (TPR) is known to play a role in mediating an inflammatory response in a variety of cells. Gut-derived lipopolysaccharide (LPS), a TLR4 agonist, is elevated in obesity. Moreover, free fatty acids (FFAs) are important mediators of obesity-related inflammation. However, the role and mechanisms by which TPR regulates the inflammatory response in human immune cells remain unclear. We sought to determine the link between TPR and obesity and the role/mechanisms by which TPR alters LPS or stearic acid (SA)-induced inflammatory response in PBMCs. Cells were pre-treated with agents blocking TPR signaling, followed by treatment with LPS or stearic acid (SA). Our findings showed that TPR mRNA levels are higher in PBMCs from individuals with obesity. Blockade of TPR as well as ROCK which acts downstream of TPR, attenuated LPS and/or SA-induced pro-inflammatory response. On the other hand, TPR activation using its agonist enhanced the pro-inflammatory effects of LPS and/or SA. Of note, TPR agonist by itself elicits an inflammatory response which was attenuated by blocking TPR or ROCK. Our data suggest that TPR plays a key role in promoting an inflammatory response in human PBMCs and this effect is mediated via TLR4 and/or ROCK signaling.

The term Conjugated Linoleic Acid (CLA) refers generically to a class of positional and geometric conjugated dienoic isomers of linoleic acid. Among the isomers of linoleic acid cis9, trans11-CLA (c9, t11-CLA) and trans10, cis12-CLA (t10, c12-CLA) are found to be bio-logically active isomers, and they occur naturally in milk, dairy products and meat from ruminants. In addition, some vegetables and some sea-foods have also been reported to contain CLA. Although the CLA levels in these natural sources are insufficient to confer the essential health benefits, anti-carcinogenic or anti-cancer effects are of current interest. In the rumen, CLA is an intermediate of isomerization and the biohydrogenation process of linoleic acid to stearic acid conducted by ruminal microorganisms. In addition to rumen bacteria, some other bacteria, such as Propionibacterium, Bifidobacterium and some lactic acid bacteria (LAB) are also capable of producing CLA. In this regard, Lactiplantibacillus plantarum (formerly Lactobacillus plantarum) has demon-strated the ability to produce CLA isomers from linoleic acid by multiple enzymatic activi-ties, including hydration, dehydration, and isomerization. L. plantarum is one of the most versatile species of LAB and the bacterium is widely used in the food industry as a micro-bial food culture. The studies reviewed in this article reveal how, in the production of some fermented foods, the use of appropriate strains of L. plantarum, as a starter or additional culture, can be considered a critical factor in the design of new CLA-enriched functional foods.

Background. Transferrin receptor 1 (TfR1), glucose transporter 1 (GLUT1), and CD98hc are candidates for targeted therapy at the blood-brain barrier (BBB). Our objective was to challenge the expression of TfR1, GLUT1, and CD98hc in brain capillaries by the histone deacetylase inhibitor (HDACi) valproic acid (VPA). Methods. Primary mouse brain capillary endothelial cells (BCECs) and brain capillaries isolated from mice injected intraperitoneally with VPA were examined using RT-qPCR and ELISA. Targeting to the BBB was performed by injecting monoclonal anti-TfR1 (Ri7217)-conjugated gold nanoparticles measured using ICP-MS. Results. In BCECs co-cultured with glial cells, Tfrc mRNA expression was significantly higher after 6 h VPA returning to baseline after 24 h. In vivo Glut1 mRNA expression was significantly higher in males, but not females', receiving VPA, whereas Cd98hc mRNA expression was unaffected by VPA. TfR1 increased significantly in vivo after VPA, whereas GLUT1 and CD98hc were unchanged. Uptake of anti-TfR1-conjugated nanoparticles was unaltered by VPA in spite upregulated TfR expression. Conclusions. VPA upregulates TfR1 in brain endothelium in vivo and in vitro. VPA does not increase GLUT1 and CD98hc proteins. The increase in TfR1 does not result in higher anti-TfR1 antibody targetability, suggesting targeting sufficiently occurs with available transferrin receptors without further contribution from accessory VPA-induced TfR1.

Cisplatin is a widely used anticancer drug for treating solid tumors, but it is associated with severe side effects, including nephrotoxicity. Various studies have suggested that the nephrotoxicity of cisplatin could be overcome; nonetheless, an effective adjuvant drug has not yet been established. Oleanolic acid acetate (OAA), a triterpenoid isolated from Vigna angularis, is commonly used to treat inflammatory and allergic diseases. This study aimed to investigate the protective effects of OAA against cisplatin-induced apoptosis and necroptosis using TCMK-1 cells and a mouse model. In cisplatin-treated TCMK-1 cells, OAA treatment significantly reduced Bax and cleaved-caspase3 expression, whereas increased Bcl-2 expression. Moreover, in cisplatin-induced kidney injury mouse model, OAA treatment alleviated weight loss in the body and major organs and also relieved cisplatin-induced nephrotoxicity symptoms. RNA sequencing analysis of kidney tissues identified lipocalin-2 as the most upregulated gene by cisplatin. Additionally, necroptosis-related genes such as receptor interacting protein kinase (RIPK) and mixed lineage kinase domain like (MLKL) were identified. In vitro study, the phosphorylation of RIPKs and MLKL was reduced by OAA pretreatment in both cisplatin-treated cells and cells boosted by co-treatment with z-VAD-FMK. In conclusion, OAA could protect the kidney from cisplatin-induced nephrotoxicity and may serve as an anticancer adjuvant.

In principle, modular or integral character of manufacturing lines depends on topological designs of products and determined operation tasks. On the other hand, in specific situations there is an articulated need for modular design in smart manufacturing systems, since modular layouts are a crucial step towards agile production via smart manufacturing. The aim of this paper is to explore how the modular layout relates to manufacturing lead time (MLT) and to operational complexity of smart manufacturing systems. For this purpose, topologically different models of alternative process layouts were simulated and tested, while MLT values were obtained using Tecnomatix Plant Simulation. Obtained positive findings of this research could be useful not only in selection of the most suitable process design from the alternative ones, but especially in deepening knowledge and better understanding of the concept of optimal network modularity.

The heavy metal lead (Pb) can irreversibly damage the human nervous system. To help understand Pb-induced damage, we applied a genetically encoded Förster resonance energy transfer (FRET)-based Pb biosensor Met-lead 1.44 M1 to two living systems to monitor the concentration of Pb: induced pluripotent stem cell (iPSC)-derived cardiomyocytes as a semi-tissue platform, and Drosophila melanogaster fruit flies as an in vivo animal model. Different FRET imaging modalities were used to obtain FRET signals, which represented the presence of Pb in the tested samples in different spatial dimensions. Using iPSC-derived cardiomyocytes, the relationship between beating activity (20–24 beats per minute, bpm) determined from the fluctuation of fluorescent signals and the concentrations of Pb represented by the FRET emission ratio values of Met-lead 1.44 M1 was revealed from simultaneous measurements. Pb (50 μM) affected the beating activity of cardiomyocytes, whereas two drugs that stop the entry of Pb differentially affected this beating activity: verapamil (2 μM) did not reverse the cessation of beating, whereas 2-APB (50 μM) partially restored this activity (16 bpm). The results clearly demonstrate a potential of this biosensor system as an anti-Pb drug screening application. In the Drosophila model, Pb was detected within the adult brain or larval central nervous system (Cha-gal4>UAS-Met-lead 1.44 M1) using fast epifluorescence and high-resolution two-photon 3D FRET ratio image systems. The tissue-specific expression of Pb biosensors provides an excellent opportunity to explore the possible Pb-specific populations within living organisms. We believe that this integrated Pb biosensor system can be applied to the prevention of Pb poisoning and advanced research on Pb neurotoxicology.

Pipelines extend thousands of kilometers to transport and distribute oil and gas. Given the challenges often faced with corrosion, fatigue, and other issues on steel pipes, the demand for glass fiber reinforced plastics (GFRP) pipes is increasing in the oil and gas gathering and transmission systems. However, the medium transported through these pipelines contains multiple acid gases such as CO2 and H2S, as well as ions including Cl-、Ca2+、Mg2+、SO42-、CO32- and HCO3-. These substances can cause a series of problems, such as aging, debonding, delamination, and fracture. In this study, a series of aging damage experiments were conducted on V-shaped GFRP pipes with depths of 2mm and 5mm. The aging and failure of GFRP were studied under the combined effects of external force and acidic solution using acoustic emission (AE) techniques. It was found that the acidic aging solution promoted matrix damage, fiber/matrix desorption, and delamination damage in GFRP pipes over a short period. However, the overall aging effect was relatively weak. Based on the experimental data, the SSA-LSSVM algorithm was proposed and applied to the damage pattern recognition of GFRP. An average recognition rate of up to 90% was achieved, indicating that this method is highly suitable for analyzing AE signals related to GFRP damage.

The terpolymers of N-vinylpyrrolidone (VP) with acrylic acid and triethylene glycol methacrylate were synthesized with more than 90% yield by radical copolymerization in ethanol from monomeric mixtures of different composition (98 : 2 : 2, 95 : 5: 2 and 98 : 2: 5). Their physical and chemical characteristics such as monomer composition, absolute molecular masses and hy-drodynamic radii in aqueous media at different temperature were determined. The temperature effect on the behavior of terpolymers in water and aqueous saline buffer solution with pH 7.4 has been studied and the ability of a copolymer enriched with dimethacrylates units was discovered to respond to a temperature change in these media. On the basis of terpolymers and linear polyvi-nylpyrrolidone (PVP), polymer compositions of hydrophobic dye methyl pheophorbide a, MPP, that is fluorescent in the red region of the spectrum, were obtained; the sizes of the polymer nanostructures of MPP in water were determined. The structures based on terpolymers were demonstrated to be more stable than MPP-PVP ones. It was carried out the quantum-chemical modelling of the possible structures of MPP-copolymer that formed as a result of intermolecular interaction between MPP and terpolymer’s chains; the possibility of the formation of hydrogen bonds between the donors of the electrons of terpolymer units and the proton donors of the MPP molecule was shown. Using the MTT test, it was established that copolymers of various compositions are low toxic for non-tumor Vero cells and HeLa tumor cells. It was shown that the cytotoxicity of polymer particles loaded with MPP for FetMSC and HeLa cells increased. Using fluorescence microscopy, the accumulation and distribution of polymer particles in non-tumor (FetMSC) and tumor (HeLa) cells was studied and an increase in the accumulation of MPP with both types of particles was shown.

We describe a novel system for online prediction of lead seizures from long-term intracranial electroencephalogram (iEEG) recordings for canines with naturally occurring epilepsy. This study adopts new specification of lead seizures, reflecting strong clustering of seizures in observed data. This clustering results in fewer lead seizures (~7 lead seizures per dog), and hence new challenges for online seizure prediction, that are addressed in the proposed system. In particular, machine learning part of the system is implemented using the Group Learning method suitable for modeling sparse and noisy seizure data. In addition, several modifications for the proposed system are introduced to cope with non-stationarity of noisy iEEG signal. They include: (1) periodic re-training of SVM classifier using most recent training data; (2) removing samples with noisy labels from training data; (3) introducing new adaptive post-processing technique for combining many predictions made for 20-second windows into a single prediction for 4 hr segment. Application of the proposed system requires only 2 lead seizures for training the initial model, and results in high prediction performance for all four dogs (with mean 0.84 sensitivity, 0.27 time-in-warning, and 0.78 false-positive rate per day). Proposed system achieves accurate prediction of lead seizures during long-term test periods, 3–16 lead seizures during 169–364 days test period, whereas earlier studies did not differentiate between lead vs. non-lead seizures and used much shorter test periods (~few days long).

Whey protein was pretreated with multi-frequency ultrasound in mono, dual, and tri-frequency modes. The effect of multi-frequency ultrasound pretreatment on the hardness, chemical forces, and microstructure of acid-induced whey protein gel was investigated. Whey protein gels pretreated with dual and tri-frequency ultrasound showed higher hardness (p3.35 mm) in those samples were resisted to gastric digestion. Moreover, the tri-frequency ultrasound pretreatment of whey protein gel released the least free amino group during gastric digestion. In contrast, whey protein gel with the mono-frequency ultrasound pretreatment released the highest amount of free amino acid group during intestinal digestion. Findings from this study suggested that gel hardness and network density could modulate the digestion behaviors of protein gels.

The poly lactic acid (PLA) is one of the most used bio-derived thermoplastic polymers in 3D and 4D printing applications. The determination of PLA surface properties is of capital importance in 3D/4D printing technology. (1) Background: The surface thermodynamic properties of PLA polymer were determined by using the inverse gas chromatography (IGC) technique at infinite dilution. The determination of the retention volume of polar and non-polar molecules adsorbed on the PLA particles filling the column allowed us to obtain the dispersive, polar, and Lewis’s acid-base surface properties at different temperatures from 40 °C to 100 °C. (2) Methods: the applied surface method was based on our recent model that used the London dispersion equation and the new chromatographic parameter function of the deformation polarizability and the harmonic mean of the ionization energies of the PLA polymer and organic molecules. (3) Results: The application of this new method led to the determination of the dispersive and polar free surface energy of adsorption of molecules on the polymeric material, as well as the glass transition and the Lewis acid-base constants. (4) Conclusions: four interval temperatures were distinguished showing four zones of the variations of the surface properties of PLA as a function of the temperature before and after the glass transition.

Kynurenic acid (KYNA), a tryptophan metabolite, is believed to exert neuromodulatory and neuroprotective effects in the brain. The study aimed to examine the KYNA’s capacity to modify gene expression and the activity of cellular antioxidant enzymes in specific structures of the sheep brain. Anestrous sheep were infused intracerebroventricularly with two KYNA doses: lower (4×5 μg/60 μL/30 min, KYNA20) and higher (4×25 μg/60 μL/30 min, KYNA100) at 30min intervals. The abundance of superoxide dismutase (SOD2), catalase (CAT) and glutathione peroxidase (GPx1) mRNA, as well as enzyme activities (µM/µg of protein), were determined in the hypothalamic medial-basal (MBH) and preoptic (POA) areas, and in the hippocampal CA1 field. Both doses of KYNA caused a decrease (P&lt;0.01) in the expression of SOD2 and CAT mRNA in all structures examined compared to the control group (except for CAT in the POA at the KYNA100 dose). Furthermore, lower levels of SOD2 mRNA (P&lt;0.05) and CAT mRNA (P&lt;0.01) were found in the MBH and POA and in the POA and CA, respectively, in sheep administered with the KYNA20 dose. Different stimulatory effects on GPx1 mRNA expression were observed for both doses (P&lt;0.05-P&lt;0.01). KYNA exerted stimulatory, but dose-dependent effects on SOD2, CAT and GPx1 activities (P&lt;0.05-P&lt;0.01) in all brain tissues examined. The results indicate that KYNA may influence the level of oxidative stress in individual brain structures in sheep by modulating the expression of genes and activity of at least SOD2, CAT and GPx1. The present findings also expand the general knowledge about the potential neuroprotective properties of KYNA in the central nervous system.

Current Li battery technology employs graphite anode and flammable organic liquid electrolytes. Thus, current Li battery is always facing the problems of low energy density and safety. Additionally, sustainable supply of Li due to scarce abundance of Li sources is another problem. All-solid-state Mg battery is expected to solve the problems owing to non-flammable solid-state electrolytes, high capacity/safety of divalent Mg metal anode and high abundance of Mg sources. Therefore, solid-state electrolytes and all-solid-state Mg battery have been researched intensively last two decades. However, realization of all-solid-state Mg battery is still far. In this article, we review recent research progress on all-solid-state Mg battery so that researchers can pursue recent research trend of all-solid-state Mg battery. At first, solid-state electrolyte research is described briefly in the categories of inorganic, organic and inorganic/organic composite electrolytes. After that, the recent research progress of all-solid-state Mg battery is summarized and analyzed. To help readers, we tabulate electrode materials, experimental conditions and performances of all-solid-state Mg battery so that the readers can find necessary information at a glance. In the last, challenges to realize the all-solid-state Mg batteries are visited.

Silicon has been proved to be one of the most promising anode materials for the next generation of lithium-ion battery. For the application in batteries, Si anode should have high capacity and must be industrially scalable. In this study, we have designed and synthesised a hollow structure to meet these requirements. All the processes are carried out without special equipment. The Si nanoparticles that are commercially available are used as the core sealed inside TiO₂ shell, with rationally designed void space between the particles and shell. The Si@TiO₂ are characterised using X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), and scanning electron microscope (SEM). The optimised hollow structured silicon nanoparticles, when used as anode in lithium-ion battery, exhibit a high reversible specific capacity over 600 mAhg-1. This excellent electrochemical property of the nanoparticles can be attributed to their optimised phase and unique hollow nanostructure.

This paper proposes an ARIMA approach to battery health forecasting with accuracy improvement by K shape-based clustered predictors. The health prediction of the battery pack is an important function of a battery management system in data centers. Accurate forecasting of battery life turns out to be very difficult without failure data to train a good forecasting model in real life. The conventional ARIMA model is compared with total and clustered predictors for battery health forecasting. Results show that the forecasting accuracy of the ARIMA model significantly improved by utilizing the results of the clustered predictors for 40 batteries in a real data center. One year of actual historical data of 40 batteries of large scale datacenter is presented to validate the effectiveness of the proposed methodology.

Primary biliary cholangitis (PBC) is a cholestatic liver disease characterized by immune-mediated injury to small bile ducts. Although PBC is an autoimmune disease, the results of traditional immunosuppressive therapy are disappointing. Nearly 40% of PBC patients do not respond to the first-line drug UDCA. Without appropriate intervention, PBC patients would eventually progress to liver cirrhosis and even death. There is an urgent need to develop new therapies. The gut-liver axis emphasizes the interconnection between the gut and the liver, and there is increasing evidence that gut microbiota and bile acids play an important role in cholestatic diseases. Dysbiosis of gut microbiota, imbalance of bile acids, and immune-mediated bile duct injury constitute the triad of pathophysiology in PBC. Understanding the gut microbiota-bile acid network and corresponding immune functions in PBC provides a new perspective for its treatment strategies. Therefore, we summarize the latest advancements in research of gut microbiota and bile acids in PBC and, for the first time, explore the potential of immune factors related to them as novel immunotherapy targets. This article discusses potential therapeutic approaches focusing on regulating gut microbiota, maintaining bile acid homeostasis, their interactions, and related immune factors.

Lead halide perovskite has become a promising candidate for high-performance photodetector (PD) applications due to its attractive optical and electrical properties such as high optical absorption coefficient, high carrier mobility, and long carrier diffusion length. However, the presence of highly toxic lead in these devices has limited their practical applications and even hindered their progress toward commercialization. Therefore, the scientific community has been committed to searching for low-toxic and stable perovskite-type alternative materials. Lead-free double perovskite materials, which are still in the preliminary stage of exploration, have achieved inspiring results in recent years. In this review, we mainly focused on two types of lead-free double perovskite based on different Pb substitution strategies, including A2M(I)M(Ⅲ)X6 and A2M(IV)X6. We reviewed the research progress and prospects of lead-free double perovskite photodetectors in the past three years. And more importantly, from the perspective of optimizing inherent defects in materials and improving device performance, we proposed some feasible pathways and made an encouraging perspective for the future development of lead-free double perovskite photodetectors.

Fruit cracking or splitting, a severe physiological disease that highly affects appearance and quality, compromise the commodity value of fruit and also causes huge economical losses to the producers of several fleshy fruit crops. The growth-promoting phytohormone gibberellic acid (GA) and growth-inhibiting phytohormone abscisic acid (ABA) antagonistically regulate numerous developmental processes throughout the plant life cycle. Homeostasis of endogenous GA and ABA play a significant role in the normal growth of fruits, and its imbalance may lead to the occurrence of cracking or splitting during the process of fruit growth, development, ripening and postharvest storage. The pathways of GA and ABA metabolism and signaling have been studied widely, and the major components were well characterized, which including the genes encoding major biosynthesis and catabolism enzymes and the key signaling components. Nevertheless, our knowledge of the mechanisms of GA and ABA governing fruit cracking is not comprehensive enough. In this review, we not only focus on the scenarios of effects of endogenous GA and ABA contents in the fruit and exogenous plant growth regulators GA and ABA treatments, but also endeavor to provide some genetic cues on the function of GA and ABA responsible for fruit cracking modulation. Information from this review aims to strengthen the understanding of potential molecular bases underlying GA and ABA in fruit cracking control and provide guidance in breeding of fruit cultivars with cracking-resistant ideotypes, and also make great theoretical significance in guiding the establishment of integrated prevention and control measures to fruit cracking or splitting.

Recently, polyacetylene (PA) is receiving a renewed scientific attention due to its electrical properties potentially useful for energy applications (e.g., fabrication of electrodes for batteries and supercapacitors) and unique functional characteristics (e.g., flame retardant, oxygen scavenger, EMI-shielding, etc.). This chemical compound can be obtained in form of a polyacetylene-PVOH copolymers simply by chemical dehydration of poly(vinyl alcohol) (PVOH), which is a very common type of polymer, widely used in packaging and other technological areas. This very inexpensive chemical reaction for the large-scale synthesis of PA/polyvinylenes has been investigated by reacting PVOH with fuming sulfuric acid at room temperature. In this process, PVOH, shaped in form of film, is dipped in fuming sulfuric acid (i.e., H₂SO₄ at 95-97%) and, after complete chemical-dehydration, it has been mechanically removed from the liquid phase by using a nylon sieve. The reduction process leads to a substantial PVOH film conversion to PA as it has been proved by infrared spectroscopy (ATR-mode). Indeed, the ATR spectrum of the reaction product included all characteristic absorption bands of PA. The reaction product has been also characterized by UV-Vis spectroscopy in order to evidence the presence in the structure of conjugated carbon-carbon double bonds of various lengths. Differential scanning calorimetry (DSC) and thermogravimetric analysis have been used respectively to investigate the PA solid-state cis-trans isomerization and thermal stability in air and nitrogen, respectively.

This study investigated the effects of exogenous gibberellic acid (GA) treatments (elongating cluster + seedless + expanding, T1; seedless + expanding, T2; expanding, T3 and water, CK) on the content of sugars, organic acids, and endogenous hormones and sink strength.Results showed that T2 treatment displayed the highest fructose and glucose levels at 100 days after treatment (DAT), whereas its effect on tartaric acid, malic acid, and citric acid concentrations at 80 and 100 DAT was relatively weak. Under GA3 treatments, both GA3, IAA, and CTK contents increased, whereas ABA contents decreased at 1, 2, 4, 8, and 48 h. Analysis of sugar phloem unloading revealed that T2 treatment exhibited the highest values during softening and ripening stages. Our findings indicate that appropriate GA3 application can positively influence sink strength by regulating sink size and activity, including berry size enlargement, sugar phloem unloading and sugar accumulation in grape sink cells.

Two interesting compounds such as quaternary ammonium lignin(QAL) and 2-ethylhexyl phosphoric acid mono-2-ethylhexyl ester (P507) were synthesized as ionic liquids(QP-ILs) for the extraction of metal ions. The extraction behavior of Co(II) and Ni(II) from chloride solution was compared between QP-ILs and P507. The results showed that the extraction rates of Co(II) and Ni(II) in the two solutions varied with the extraction conditions, but QP-ILs has stronger extractability for cobalt than P507, while Ni is on the contrary. Under the same conditions, the Co/Ni separation performance(βCo/Ni) in QP-ILs is superior to that in p507. At pH4.0, 55℃, concentration of 20%, extraction time of 10 minutes, the βCo/Ni of QP-ILs reached to 2703, while that of P507 was only 164. In conclusion, QP-ILs was more efficient than P507 for separating Co from mixed solutions.

The broad and rapid application of new genomic techniques (NGTs) such as CRISPR-Cas has led to a fast increase in the number of genetically modified crops. With the recently published EU Commission’s (EC) regulatory proposal on plants generated with NGTs (July 5, 2023) the process of admission of such genetically modified plants is aimed to get accelerated and simplified. NGT plant applications shall be categorized based on their molecular characteristics into category 1 NGT (NGT1) and category 2 NGT (NGT2), which is in divergence from the current legislation centered around Directive 2001/18/EC. In the regulatory proposal NGT2 plants are envisioned to undergo a reduced risk assessment while for NGT1 plants no risk assessment is foreseen at all. To demonstrate were the path of the proposal leads to in practice, we applied the proposed criteria for categorization to a list of NGT plant applications that are currently in the commercialization pipeline. A key finding is that out of those plant applications affected by the EC proposal, 94% would be classified as NGT1 and thus would receive a market approval without risk assessment, monitoring and sufficient labeling provisions. The remaining 6% of applications would be classified as NGT2 plants for which, in deviation from the current regulation, an adapted risk assessment is proposed. A screening of intended traits in the pipeline highlights that certain NGT1 plants can pose similar environmental risks (e.g. invasiveness) compared to other genetically modified organisms (GMOs), as defined in Directive 2001/18/EC. For example, NGT1 applications based on RNAi technology can exhibit insecticidal effects with potential side effects on non-target organisms (i.e. other insects). Our quantitative and case-specific elaboration on how the current EC regulatory proposal would affect the environment, health or consumer protection will be informative for decision makers and politicians.

This study presented a novel and sustainable method for producing chitin nanocrystals (PA-ChNCs) using phosphoric acid hydrolysis. The produced PA-ChNCs were used as stabilizers for Pickering emulsions and their physicochemical properties as well as stabilization mechanisms were systematically investigated. The PA-ChNCs exhibited small particle sizes and high surface areas, enabling an effective adsorption at the oil/water interface, which prevented coalescence in Pickering emulsions. The particle size and surface charge PA-ChNCs were strongly pH-dependent, which were critical factors for stabilizing Pickering emulsions. The study showed that emulsions with higher O:W ratios (50%) exhibited larger droplets but greater viscosity, forming a stable gel-like matrix that was more stable than emulsions with other O:W ratios after storage for 30 days. Emulsions with higher PA-ChNCs concentrations (2.0 wt%) and higher pH values (pH 10) showed small droplets and high viscosity, leading to stable emulsions. This research contributes to the development of sustainable and effective emulsifiers for use in the food industry, making utilization of seafood waste in an eco-friendly manner possible. Overall, this study highlights the potential of using newly developed PA-ChNCs as stabilizers for Pickering emulsions in food products.

The safety concerns associated with current lithium-ion batteries are a significant drawback. A short-circuit within the battery's internal components, such as those caused by a car accident, can lead to ignition or even explosion. To address this issue, a polymer shear thickening electrolyte, free from flammable solvents, has been developed. It comprises a star-shaped oligomer derived from a trimethylolpropane (TMP) core and polyether chains, along with the inclusion of 20 wt.% nanosilica. Notably, the star-shaped oligomer serves a dual function as both the solvent for the lithium salt and the continuous phase of the shear thickening fluid. The obtained electrolytes exhibit an ionic conductivity of 10-6 S cm-1 at 20 °C and 10-4 S cm-1 at 80 °C, with a high Li+ transference number (t+ = 0.79). A nearly thirtyfold increase in viscosity to a value of 1187 Pa s at 25 °C and a critical shear rate of 2 s-1 were achieved. During impact, this electrolyte could enhance cell safety by preventing electrode short-circuiting.

New nanocomposite material was prepared by high pressure processing of starting glass of nominal composition NaFePO$_{4}$. Thermal, structural, electrical and dielectric properties of the prepared samples were studied by differential thermal analysis (DTA), X-ray diffraction (XRD) and broadband dielectric spectroscopy (BDS). It was demonstrated that high pressure – high temperature treatment (HPHT) led to an increase of electrical conductivity of initial glasses by 2 orders of magnitude. It was also shown that the observed effect was stronger than for lithium analogue of this material studied by us earlier. The observed enhancement of conductivity was explained by Mott’s theory of electron hopping, which is more frequent in sample after pressure treatment. The final composite consisted of nanocrystalline NASICON and alluaudite phases, which are electrochemically active in potential cathode materials for Na batteries. Average dimensions of crystallites estimated from XRD studies were between 40 and 90 nm, depending on the phase. Some new aspects of local dielectric relaxations in studied materials were also discussed. It was shown that a combination of high pressures and BDS method is a powerful method to study relaxation processes and molecular movements in solids. It was also pointed out that high-pressure cathode materials may exhibit higher volumetric capacities compared with commercially used cathodes with carbon additions.

Today, enhancing food preservation and safety in the spirit of the bioeconomy suggests the use of biodegradable polymers such as poly-L-lactic acid (PLA) in food packaging and the replacement of chemical additives with natural antioxidant/antibacterial agents such as essential oils and their derivatives. Herein a novel carvacrol (CV) @ natural zeolite (NZ) nanohybrid was developed by employing a new vacuum adsorption desorption method which results in the adsorption of a high CV amount on NZ equal to 61.7 %wt. This CV@NZ nanohybrid was successfully dispersed in a PLA/triethyl citrate (TEC) matrix via a melt-extrusion process to obtain PLA/TEC/xCV@NZ nanocomposite films with 5, 10 and 15 CV@NZ %wt. content. PLA/TEC/xNZ films were also de-veloped for comparison. The overall study resulted in a biodegradable active film with the fol-lowing properties: 10%wt. CV@NZ content (PLA/TEC/10CV@NZ), self-healable properties, 22% higher tensile strength and 40% higher elongation at break, 45% higher water barrier and 40% higher oxygen barrier than pure PLA/TEC matrix. This film also provides high CV release content, high CV control release rate as well as significant antioxidant activity and antibacterial activity against the food pathogens Staphylococcus aureus and Salmonella enterica spp. enterica serovar Typhimurium. This film not only succeeds in extending the shelf-life of fresh pork minced, as shown by total variable count measurements in four days, but also prevents lipid oxidation of fresh minced pork and maintains the minced meat in higher nutritional conditions, as revealed by the heme iron content determination, and in a much better and acceptable sensory condition than the commercial packaging paper.

Background: Although the link between environmental lead exposure and several patterns of cardiovascular disease (CVD) has been reported, its association with silent myocardial infarc-tion (SMI) has not been explored. We aimed to assess the association between blood lead levels (BLL) and risk of SMI. Methods: This analysis included 7283 (mean age 56.1±2.52 years, 52.5% women) participants from the Third National Health and Nutrition Examination Survey who were free of clinical CVD. Ascertainment of BLL done using graphite furnace atomic absorption spectrophotometry. SMI defined as ECG evidence of MI without history of MI. Multivariable lo-gistic regression analysis was used to examine the association between SMI and BLL. Results: SMI was detected in 120 participants corresponding to an unweighted prevalence of 1.65%. Par-ticipants with higher levels of BLL had higher prevalence of SMI (0.4%, 0.9%, and 2.4% across BLL tertiles; p-value

Hybrid organic–inorganic perovskites (HOIPs) are promising materials in several fields related to electronics, offering long carrier-diffusion lengths, high absorption coefficients, tunable band gaps, and long spin lifetimes. Recently, chiral perovskites have attracted a huge interest thanks to the possibility of further widening the applications of HOIPs. Chiral materials, being intrinsically non-centrosymmetric, display several attractive physico-chemical properties, including circular dichroism, circularly polarized photoluminescence, nonlinear optics, ferroelectricity, and spin-related effects. Recent studies have shown that chirality can be transferred from the chiral organic ligands into the inorganic perovskite framework, resulting in materials combining the advantages of both chirality and perovskite superior optoelectronic characteristics. Thus, chiral HOIPs have emerged as promising materials for chiroptoelectronic, spintronic, and ferroelectric applications. Here, we report a summary of the latest advances in the field of chiral HOIPs, with a specific focus on lead-free materials and on the first attempts to understand the correlation between the crystal structure features and the chirality-induced functional properties

: The objective of this work is to elucidate the role of partnerships and the number of partners necessary for lead user innovation outcomes. Lead user theory identifies these users as being ahead of market trends and experiencing significant benefits from innovating. So far, most lead user research has concentrated on firms and not individual lead users’ perspective. Data were obtained using a quantitative design during which 321 respondents participated. The SPSS software was used to analyze the data and determine significance. These findings indicate a connection between number of partners and lead user innovation success. This demonstrates that number of partners is significant in determining the success or failure of an innovation. This study provides empirical evidence that the number of partners is an essential factor that influences the success of innovation, and establishes the absolute numbers for achievement of successful innovation. Future studies must investigate the possible implications of integrating the partner variables with other characteristics of the lead user.

This paper presents the results of an experimental study of the patterns of steel and lead shot transformation under the impact of environmental factors (two types of shot exposed alone and in combination with each other). The analyzed environmental factors include atmospheric precipitation of various acidity and soil solutions with a higher content of organic acids. This research demonstrated that steel shot is characterized by a high transformation rate that is an order of magnitude higher on average than the transformation rate of lead under the same conditions. The prevalence of the suspended iron form (excluding the interaction with organic acids) presents risks for such environmental components as soils and sediments and may be hazardous to the ambient air and natural waters in case of wind erosion and surface runoff from the catchment area. Furthermore, the joint presence of steel and lead shot mutually accelerates the corrosion of both metals, thus increasing the environmental risks.

This work shows a correlation between light reflectance, absorption, and morphologies of series of (1-x) BM–x PT, (x = 0.0, 0.02, 0.04, 0.08, 0.12, 0.16, 0.24) ceramics composite. The (1-x) BM–x PT showed features of a black mirror with a low optical energy gap. The measured Vis-NIR diffused reflectance enabled the calculation of the energy gap using the modified Kubelka-Munk function. The estimated energy gap was lower than 1.5 eV related to low reflectance in the Vis-NIR range. Moreover, obtained histograms of grains, using scanning electron microscope, enabled the correlation between grains size and amount of lead titanate. We deduced from the ceramics surface morphology that marked porosity also induced reflectivity of low magnitude. We correlated the magnitude of the energy gap with phases of the BM-PT composite and with the electrical conductivity activation energy reported in the literature. Our results findings opened prospect studied materials for optical applications.

In agriculture, soil-borne fungal pathogens, especially Fusarium oxysporum strains, are posing a serious threat to efforts to achieve global food security. In the search for safer agrochemicals, silica nanoparticles (SiO2NPs) have recently been proposed as a new tool to alleviate pathogen damage including Fusarium wilt. Hollow mesoporous silica nanoparticles (HMSNs), a unique class of SiO2NPs, have been widely accepted as a desired pesticide carrier. However, their role in enhancing the disease resistance and the specific mechanism remain unknown. In this study, three sizes of HMSNs (19, 96 and 406 nm as HMSNs–19, HMSNs–96 and HMSNs–406, respectively) were synthesized and characterized to determine their effects on seed germination, seedling growth, and Fusarium oxysporum f. sp. phaseolus (FOP) suppression in cowpea roots by foliar spray using phenotypes, fresh biomass and disease progression as indicators. The results revealed that three HMSNs exhibited no adverse impacts on seed germination and tended to improve plant growth. Also, they exert their FOP suppression with a size- and concentration-dependent manner. HMSNs–406 possessed the best control effect at a concentration of 1000 mg/L showing an upto 40.00% decline in the disease severity. The Si(OH)4 control was also effective on FOP suppression at a lower concentration of 100 mg/L, whereas its higher concentrations exhibited obviously adverse impacts on FOP control, seed germination and plant growth. Moreover, we conformed that HMSNs posed their Fusarium wilt suppression in cowpea plant by activating SA (salicylic acid)-dependent SAR (systemic acquired resistance) responses rather than directly suppressing FOP. A higher level of SA content and elevated expression of its maker genes of PR-1 and PR-5 in HMSNs–406 treated cowpea roots provided substantial evidences of this mode of action. Other resistance-related genes, as well as defense-responsive enzymes, were also involved in the HMSNs-activated SAR pathway. Overall, for the first time, our results extended a new role of HMSNs as a potent elicitor to serve as a versatile alternative for plant disease protection of low cost, highly efficiency and sustainability.

p-Toluenesulfonic acid is commercially available, non-toxic, cheap organic compound with robust stability. p-Toluenesulfonic acid is solid, non-corrosive and a strong organic acid that can be handled easily. Due to this p-toluenesulfonic acid could be the better replacement of other conventional acids like nitric acid, sulfuric acid, perchloric acid and AlCl3 in organic transformations. Moreover, p-toluenesulfonic acid could be used synergistically with other mode of catalysis like transition metal catalysis and photocatalysis. In recent years, the use of this solid organic acid in organic and polymer synthesis has grown tremendously. In this review, we present an overview of p-toluenesulfonic acid promoted various organic reactions with particular emphasis to the more recently reported methods. In some cases, we also detailed the understanding of the reactions by providing the reaction mechanism. Despite these advances, there are still many opportunities for the development of new reactions using PTSA. Industry and academia have become more conscious to adopt sustainable chemical processes using safer reagents and solvents and the use of PTSA in this context is highly significant. This review will inspire researchers for further reaction development employing p-toluenesulfonic acid.

Owing to the growing concerns due to dwindling fossil fuel reserves, increasing energy demand and climate emergency, it is imperative to develop and deploy sustainable energy technologies to ensure future energy supply as well as transition to the net zero world. In this context, there is great potential in the biorefinery concept for supplying drop in biofuels in the form of biodiesel. Biodiesel as a fuel can certainly bridge the gap where electrification or the use of hydrogen is not feasible, for instance heavy vehicles, farm and marine transportation sector. However, biodiesel industry also leads to formation of large amount of crude glycerol as the byproduct. Crude glycerol due to presence of several impurities may not be a suitable feedstock for all high value products derived from glycerol but fits well with glycerol esterification for producing glycerol acetins, which have numerous applications. This review critically looks at the processes using nanostructured solid/liquid acid catalysts for glycerol esterification including the economic viability of the scale up.

This article presents a review of resources for batteries with a specific focus on sustainability aspects related to raw materials, electrode and electrolyte chemistries suitable for the automobile industry. We emphasize the importance of prioritizing sustainability in battery technology evolution, which is expected to shift towards earth-abundant materials. One notable advancement in this direction is the utilization of glass solid-state electrolytes, known for their high ionic conductivity, low electronic conductivity, and high dielectric constant. However, our review suggests that further research should explore synthesis methods to modify anisotropic properties, enhancing the performance of solid-state electrolytes, particularly in facilitating the flow of ions.

Rechargeable aqueous Zn-ion batteries (ZIBs) have attracted considerable attention owing to their high theoretical capacity of 820 mA h g‒1, low cost and intrinsic safety. However, the electrolyte leakage and the instability issues of Zn negative electrodes originating from side reactions between the aqueous electrolyte and Zn negative electrode, not only restricts the battery stability but also results in short-circuit of aqueous ZIBs. Herein we report a flexible and stable N-isopropylacrylamide/sodium alginate (N-SA) gel electrolyte, which possesses high mechanical strength and high ionic conductivity of 2.96×10‒2 S cm‒1, and enables the Zn metal negative electrode and MnO2 positive electrode to reversibly and stably cycle. Compared to the liquid electrolyte, the N-SA hydrogel electrolyte can effectively form a uniform Zn deposition and suppress the generation of irreversible by-products. The assemble symmetric Zn/Zn cells at a current density of 1 mA cm‒2 shows a stable voltage profile, which maintains a low level of about 100 mV over 2600 h without an obvious short circuit or any overpotential increasing. Specially, the assembled Zn/N-SA/MnO2 batteries can deliver a high specific capacity of 182 mAh g‒1 and maintain 98% capacity retention after 650 cycles at 0.5 A g‒1. This work provides a facile method to fabricate high-performance SA-based hydrogel electrolytes that illustrates their potential for flexible batteries for wearable electronics.

Spent batteries recycling is an important way to obtain low-cost graphite. Nevertheless, the obtaining of crystalline graphite with a rather low density of defects is required for many applications. In the present work, high-quality graphites have been obtained from different kinds of spent batteries. Black masses from spent alkaline batteries (batteries black masses, BBM), and lithium-ion batteries from smartphones (smartphone black masses, SBM) and electric and/or hybrid vehicles (lithium-ion black masses, LBM) were used as starting materials. A hydrometallurgical process was then used to obtain recycled graphites by acidic leaching. Different leaching conditions were used depending on the type of the initial black mass. The final solids were characterized by a wide set of complementary techniques.

Hepatitis B surface antigen (HBsAg) is not only the biomarker of hepatitis B virus (HBV) infection and expression activity in hepatocytes, but also contributes to viral specific T cell exhaustion and HBV persistent infection. Therefore, anti-HBV therapies targeting HBsAg to achieve HBsAg loss are key approaches for HBV functional cure. In this study, we found that YZH-106, a rupestonic acid derivative, inhibited HBsAg secretion and viral replication. Further investigation demonstrated that YZH-106 promoted the lysosomal degradation of viral L- and M-HBs proteins. Mechanistic study by Biacore and docking analysis revealed that YZH-106 bound directly to PreS2 domain of L- and M-HBsAg, thereby blocking their entry to the endoplasmic reticulum (ER) and promoting their degradation in cytoplasm. Our work thereby provide basis for design of novel compound therapy to target HBsAg against HBV infection.

The need for solvating and encapsulating hydro-sensitive molecules drives noticeable trends in the applications of cyclodextrins in pharmaceutical industry, food, polymer, materials, and agricultural science. Among them, β-cyclodextrin is one of the most used for the entrapment of phenolic acid compounds to mask the bitterness of wheat bran. In this regard, there is still a need for a good predictive model that assesses β-cyclodextrin bitterness masking capabilities for various phenolic compounds. This study uses a dataset of 20 phenolic acids docked to the β-cyclodextrin cavity to generate three different binding constants. The data from docking study were combined with topological, topographical and quantum-chemical features from the ligands in a machine learning-based structure-activity relationship study. Three different models for each binding constant were computed using a combination of Genetic Algorithm (GA) and Multiple Linear Regression (MLR) approaches. The developed ML/QSAR models showed a very good performance, with high predictive ability and correlation coefficients of 0.969 and 0.984, for training and test sets, respectively. The models revealed several factors responsible for a binding with cyclodextrin, showing positive contributions toward the binding affinity values, including such features as presence of six-membered rings in the molecule, branching, electronegativity values, and polar surface area.

Bile acids (BA) are classically known as an agent important in lipid absorption and cholesterol metabolism. Nowadays, BAs have been found to be involved in various cellular signaling pathways such as protein kinase cascades, cyclic AMP (cAMP) synthesis and calcium mobilization. In addition, they have also been shown to regulate glucose and energy homeostasis. Bile acids are ligands for several nuclear hormone receptors, including FXR. Recently, muscarinic receptor and TGR5, G-protein-coupled receptor (GPCR), have been suggested to play a role in bile acid activity which is independent of nuclear hormone receptors. Moreover, BAs have also been studied in other GPCR associated pathways, namely sphingosine-1-posphate and glucagon receptor. Hydrophobic bile acids have been proven to affect heart rate and its contraction. Elevated bile acids are associated with arrhythmias in adults and fetal heart. Altered ratios of primary and secondary bile acid are reported in chronic heart failure patients. Meanwhile in patients with liver cirrhosis, cardiac dysfunction has been strongly linked to the increase of serum bile acid concentrations. In contrast, the most hydrophilic BA known as ursodeoxycholic acid has been found beneficial in improving peripheral blood flow in chronic heart failure patients and protecting heart against reperfusion injury.

The paper discusses the mechanism of montmorillonite structure alteration and bentonites properties modification (on the example of samples from clay deposit Taganka, Kazakhstan) due to the thermochemical treatment (treatment with inorganic acid solutions at different temperatures, concentrations and reaction times). With the use of the suit of methods certain processes were distinguished: transformation of montmorillonite structure, which appears in the leaching of interlayer and octahedral cations, protonation of the interlayer and OH groups at octahedral sheets. Changes in the structure of the 2:1 layer of montmorillonite and its interlayer result in significant changes in the properties – reduction of cation exchange capacity and an increase of specific surface area. The results of the work showed that bentonite clays retain a significant portion of its adsorption properties even after the long term and intense thermochemical treatment (6M HNO3, 60°C, 108 hours)

The Lead-DBS imaging toolbox reconstructs the location of β-oscillations in the subthalamic nucleus (STN) in patients with Parkinson’s disease. The objective was to compare this probabilistic location with those of intraoperative monopolar β-oscillations (Vercise Cartesia directional electrodes, Boston Scientific). Also, the efficacy of stimulated structures in reducing motor symptoms were analysed. β-oscillations were computed from local field potentials [0.5-3kHz] by using shielded wires for monopolar recordings with an extracranial shielded reference. For each electrode contact, power spectral densities of the β-band [13-31Hz] were compared with those of all eight electrode contacts. The DISTAL, electrophysiological, and DBS target atlases of the Lead-DBS toolbox were applied to the reconstructed electrodes from preoperative MRI and postoperative CT. Thirty-six electrodes (20 patients: 7 female, 13 male; 16/20 both, 4/20 single STN) were analysed. Stimulation sites dorsal and/or lateral to the sensorimotor STN were most efficient. In 33/36 electrodes at least one contact was measured with stronger β-oscillations, 23 in or touching the ventral subpart of the probabilistic volume with β-oscillations, 10 not located in or touching but adjacent to this volume; in 3/36 electrodes, no contact was found with β-oscillations, they were distant from this volume. Monopolar local field potentials confirmed the ventral subpart of the probabilistic β-oscillations.

SARS-CoV-2 was detected in China in December 2019. Myocardial injury is a crucial presentation of COVID-19, based on the association of ACE-2 and SARS-CoV-2. Down-regulating ACE-2 decreases the cardioprotective effects of angiotensin, leading to a higher TNF-α activation. TNF-α causes the inflammatory response in the myocardial damage as an apoptotic inducer. Moreover, as an inducer of necroptosis, TNF-α binds to a part of TNF receptor 1, which involves receptor-interacting protein 1 (RIP1) and causes cell death through RIP1 inhibition and NF-κB stimulation, which are also done through Tpl-2. Calcineurin controls the Tpl-2-driven NFAT stimulation. Bcl-2 or Bcl-X_L entirely blocks these pathways. Bcl-2 overexpression reduces FasL expression with a mechanism based on Bcl-2 inhibiting the NFAT. Moreover, the Fas/FasL system activates apoptosis in various cells. Bcl-XL stimulates Fas-related cell death. Additionally, TNF-α, as a part of inflammatory cytokine storms, indirectly interacts with NFAT/Bcl-2 through Tpl-2/NF-κB. Diversely, TNF-α and IL-1ẞ, the basis of inflammatory cytokine storms in COVID-19, can stimulate generating NO. Also, IL-2 is highly up-regulated in COVID-19 patients and stimulates NO generation in patients. TNF-α can provoke the generation of superoxides in neutrophils. A well-determined mechanism is the intracellular production of NO via calcium-calmodulin-dependent NO synthase (NOS). NO enhances NFAT’s calcium-dependent activity. Also, Intra/extracellular calcium exchange activates calcineurin and its related molecule, NFAT. Nitration provokes RIP1 necroptosis cascade, with respiratory complex I. Nitrites converse protection against ischemia-reperfusion injuries in the myocardium. Regulating this intrinsic molecular pathway can prevent the necroptosis of cardiomyocytes.

Most methods for measuring environmental lead (Pb) content are time consuming, expensive, hazardous, and restricted to specific analytical systems. To provide a facile, safe tool to detect Pb, we created pMet-lead, a portable fluorescence resonance energy transfer (FRET)-based Pb biosensor. pMet-lead comprises a 3D-printed frame housing a 405-nm laser diode — an excitation source for fluorescence emission images (YFP and CFP) — accompanied by optical filters, a customized sample holder with a Met-lead 1.44 M1 (the most recent version)-embedded biochip, and an optical lens aligned for smartphone compatibility. Measuring the emission ratios (Y/C) of the FRET component enables Pb detection with a dynamic range of nearly 2 (1.96), pMet-lead/Pb dissociation constant (K_d) 45.62 nM, and limit of detection 40 nM (0.832 μg/dL, 8.32 ppb). To mitigate earlier problems with lack of selectivity for Pb vs. zinc, we preincubated samples with tricine, a low-affinity zinc chelator. We validated pMet-lead measurements of characterized laboratory samples and unknown samples from six regions in Taiwan by inductively coupled plasma mass spectrometry (ICP-MS). Notably, two unknowns had Y/C ratios significantly higher than that of the control (3.48 ± 0.08 and 3.74 ± 0.12 vs. 2.79 ± 0.02), along with Pb concentrations (10.6 ppb and 15.24 ppb) above the WHO-permitted level of 10 ppb in tap water, while the rest four unknowns showing no detectable Pb upon ICP-MS. These results demonstrate that pMet-lead provides a rapid, sensitive means for on-site Pb detection in water from the environment and in living/drinking supply systems to prevent potential Pb poisoning.

In order to reach the theoretical efficiency limits of lead-based metal halide perovskite solar cells, the voltage should be enhanced because it suffers from nonradiative recombination. Perovskite materials contain intrinsic defects that can act as Shockley-Read-Hall recombination centers. Several experimental and computational studies have characterized such defect states within the band gap. We give a systematic overview of compositional engineering by distinguishing the different defect reducing mechanisms. Doping effects are divided into influences on: (1) Crystallization; (2) Lattice properties. Incorporation of dopant influences the lattice properties by: (a) Lattice strain relaxation; (b) Chemical bonding enhancement; (c) Band gap tuning. The intrinsic lattice strain in undoped perovskite was shown to induce vacancy formation. The incorporation of smaller ions, such as Cl, F and Cd, increases the energy for vacancy formation. Zn doping is reported to induce strain relaxation but also to enhance the chemical bonding. The combination of computational studies using (DFT) calculations quantifying and qualifying the defect reducing propensities of different dopants with experimental studies is essential for deeper understanding and unraveling insights, such as the dynamics of iodine vacancies and the photochemistry of the iodine interstitials, and can eventually lead to a more rational approach in the search for optimal photovoltaic materials.