This study aims to examine the non-volatile Particle Number (PN) emissions of a retrofitted Heavy-Duty Spark-Ignition (HD-SI) engine powered by liquefied petroleum gas (LPG) under both steady-state and transient conditions. The engine was tested under seven steady-state operating points to investigate the PN behavior and Particle Size Distribution (PSD) upstream and down-stream of the Three-Way Catalyst (TWC). This analysis intends to assess the impact of including particles with diameters ranging from 10 nm to 23 nm in the total particle count, a consideration for future regulations. The study employed the World Harmonized Transient Cycle (WHTC) for transient conditions to encompass the same engine working region used in the steady-state analysis. A Dekati FPS-4000 diluted the exhaust sample to measure the PSD and PN for particle diameters between 5.6 nm and 560 nm using the TSI-Engine Exhaust Particle Sizer (EEPS) 3090. Findings indicate that PN levels tend to increase downstream of the TWC under steady-state conditions in operating points with low exhaust gas temperatures and flows (equal to or less than 500 °C and 120 kg/h). Furthermore, the inclusion of particles with diameters between 10 nm and 23 nm leads to an increase in PN emissions by 17.70% to 40.84% under steady conditions and by an average of 40.06% under transient conditions, compared to measurements that only consider particles larger than 23 nm. Notably, in transient conditions, most PN emissions occur during the final 600 seconds of the cycle, linked to the most intense phase of the WHTC.

This study aimed to learn disturbance information to effectively control multiple small unmanned surface vehicles (USVs) for marine research purposes at sea. The learned disturbance information was used to investigate the control of multiple USV swarms based on the leading–following formation technique. Numerous studies have already been conducted on swarm control using drones in the air; however, there has been a paucity of studies on swarm control in the sea. Contrary to swarm control in aviation, the fluid density of the sea is high, and the environment is constantly changing; thus, a robot system would be significantly affected by disturbances. This ultimately influences the maintenance of swarm formations and the accomplishment of missions [1,2]. Therefore, it is difficult to control numerous moving objects while maintaining a formation at sea by using the existing aerial drone swarm control technology. To solve this problem, we learned a long short-term memory (LSTM) model with time-series marine environmental data to predict maritime disturbances. Thereafter, the model was applied to a mission-based position control algorithm of each USV constituting the swarm to design a marine unmanned floating vessel swarm control system that can be applied to various marine environments. Specifically, to effectively control numerous small USVs for marine research purposes, ocean currents are learned using the LSTM algorithm, and the predicted ocean currents are used to generate a swarm USV control system for USV formations. In this study, a control system model of several small USVs equipped with two rear thrusters and a front lateral thruster was designed. The LSTM algorithm was learned using the previous ocean current data, and the velocity of the following ocean currents was predicted. The predictions were then used as a system disturbance to determine the thrust of the controller. To measure ocean currents in the sea when each USV moves, the velocity, azimuth, and position (latitude, longitude) data from the GPS mounted on the USV were used to measure the velocity and direction of the hull's movement. Further, the flow rate was measured using a flow rate sensor on a small USV. The USV movement and position were controlled using an artificial neural network-PID (ANN-PID) controller. This study entailed a comparative analysis of the designed USV model results and those generated by the simulator, including the behavior control rule of the USV swarm and the path of the actual USV swarm at sea. It was verified that the effectiveness of the USV mathematical model and behavior control rules. By comparing the movement path of the swarm USV with and without the disturbance learning algorithm and ANN-PID control algorithm applied to the designed simulator, the position error and maintenance performance of the swarm formation were analyzed, and the application results were compared.

Background. The Stanford Health Assessment Questionnaire-Disability Index (HAQ) is widely used to measure functional ability in persons with Rheumatoid Arthritis (RA). The instrument was developed with limited involvement from persons with RA, and their perception of the instrument has not been studied in depth. The aim of this study was to explore how persons with RA experience the use of the HAQ in care. Methods. Forty persons with RA were purposefully recruited to participate in semi-structured interviews. The interviews were then analyzed qualitatively using thematic analysis. Results. The participants questioned the relevance of the HAQ but nevertheless experienced that the instrument had a profound effect on their understanding of health and how care is delivered. The analysis resulted in three themes: Problems with individual items, meaning of the summative score, and effects on care and health perceptions. Conclusions. To make the HAQ relevant to persons with RA, it needs to be revised or to include an option to select items most meaningful to the respondent. To ensure relevance, the HAQ update should preferably be co-created by researchers, clinicians and persons with RA.

The present grievous situation of the tuberculosis disease can be improved by efficient case management and timely follow-up evaluations. With the advent of digital technology this can be achieved by quick summarization of the patient-centric data. The aim of our study was to assess the effectiveness of the ODK Scan paper-to-digital system during testing period of three months. A sequential, explanatory mixed-method research approach was employed to elucidate technology use. Training, smartphones, application and 3G enabled SIMs were provided to the four field workers. At the beginning, baseline measures of the data management aspects were recorded and compared with endline measures to see the impact of ODK Scan. Additionally, at the end, users’ feedback was collected regarding app usability, user interface design and workflow changes. 122 patients’ records were retrieved from the server and analysed for quality. It was found that ODK Scan recognized 99.2% of multiple choice bubble responses and 79.4% of numerical digit responses correctly. However, the overall quality of the digital data was decreased in comparison to manually entered data. Using ODK Scan, a significant time reduction is observed in data aggregation and data transfer activities, however, data verification and form filling activities took more time. Interviews revealed that field workers saw value in using ODK Scan, however, they were more concerned about the time consuming aspects of the use of ODK Scan. Therefore, it is concluded that minimal disturbance in the existing workflow, continuous feedback and value additions are the important considerations for the implementing organization to ensure technology adoption and workflow improvements.

This study delves into hospital mobility, understood as an indicator of perceived service quality, across the Italian regions of Apulia and Emilia Romagna, utilizing logistic regression among machine learning techniques. The focus is on how structural, operational, and clinical variables impact patient perceptions of service quality, influencing their healthcare choices. Through the analysis of mobility trends with machine learning, significant differences between regions were uncovered, highlighting the influence of regional context on perceived quality. The integration of SHAP (SHapley Additive exPlanations) values into our analysis provided deeper insights into the logistic regression model, elucidating the specific contribution of each variable to perceived healthcare quality. This incorporation of SHAP values underscores the study's commitment to employing advanced, explainable AI techniques to enhance the interpretability and fairness of healthcare service evaluations. The choice of logistic regression elucidated the impact of specific variables on quality perception, offering essential insights for optimizing healthcare resource distribution and underscoring the importance of data-driven strategies to foster more equitable, efficient, and patient-centred healthcare systems. Contributing to the understanding of perceived quality dynamics within the healthcare context, the research paves the way for further investigations into enhancing accessibility and service quality, leveraging machine learning as a tool for improving healthcare services efficiency in diverse regional settings.

This article utilizes the Canny edge extraction algorithm based on contour curvature and the cross-correlation template matching algorithm to extensively study the impact of high-repetition-rate CO2 pulsed Laser on the target extraction and tracking performance of the infrared imaging detector. It establishes a quantified dazzling pattern for lasers on infrared imaging systems. By conducting laser dazzling and damage experiments, a detailed analysis of the normalized correlation between target and dazzling images is performed to quantitatively describe laser dazzling effects. Simultaneously, an evaluation system, including target distance and laser power evaluation factors, is established to determine the dazzling level and whether the target is recognizable. The research results reveal that laser power and target position are crucial factors affecting the detection performance of infrared imaging-guided weapon systems under laser dazzling. Different laser powers are required to successfully interfere with the recognition algorithm of infrared imaging-guided weapons at different distances. And laser dazzling will produce a lot of false edge information, which seriously affects the performance of pattern recognition algorithm. In laser damage experiments, the detector experienced functional damage, with a quarter of the image displaying as completely black. The energy density threshold required for functional damage to the detector is approximately 3 J/cm2. The dazzling assessment conclusions also apply to evaluating damage results. Finally, the proposed evaluation formula aligns with experimental results, objectively reflecting the actual impact of laser dazzling on the target extraction and tracking performance of infrared imaging systems. This study provides an in-depth and accurate analysis for understanding the influence of lasers on the performance of infrared imaging-guided weapons.

Currently, there is a tenacious need to find new ways to purify water by eliminating bacterial biofilms, textile dyes, and toxic water pollutants. These contaminants pose significant risks to both human health and the environment. To address this issue, in this study, we have developed an eco-friendly approach that involves synthesizing Cobalt-doped Cerium Iron Oxide (CCIO) nanocomposite (NC) using an aqueous extract of Gossypium arboreum L. stalks. The resulting nanoparticles can be used to effectively purify water and tackle the challenges associated with these harmful pollutants. Nanoparticles excel in water pollutant removal by providing high surface area for efficient adsorption, versatile design for simultaneous removal of multiple contaminants, catalytic properties for organic pollutant degradation, and magnetic features for easy separation, offering cost-effective and sustainable water treatment solutions. CCIO nanocomposite has been synthesized by green co-precipitation method due to biomolecules and co-enzymes present in the aqueous extract of Gossypium arboreum L. stalk; a single-step procedure completed in 5 h reaction time. Further, the synthesis of nanocomposites was confirmed by various characterization techniques such as Fourier-transform infrared (FT-IR) spectroscopy, X-ray diffraction (XRD), Field emission scanning electron microscopy (FE-SEM), Transmission electron microscopy (TEM), Thermogravimetric analysis (TGA), Dynamic light scattering (DLS), and Energy Dispersive X-Ray (EDX). CCIO NCs were discovered to have a spherical shape and an average size of 40 nm. Based on DLS zeta potential analysis, CCIO NCs were found to be anionic. Also, CCIO NCs showed significant antimicrobial and antioxidant activity. Overall, considering the physical and chemical properties, the application of CCIO NCs in the adsorption of various dyes (~91 %) and water pollutants (chromium = ~ 60 %) has been considered since they exhibit great adsorption capacity owing to their microporous structure which can be a step forward in water purification.

This article presents a new input device for spastic patients and others with similar symptoms. The sensor consists of a disc used to determine positions and can replace standard joysticks in medical devices such as electric-powered wheelchairs. Using a standard joystick while operating a powered wheelchair can result in dangerous situations when spastic movements occur and extremities cramp making them uncontrollable. To avoid this, a disc was developed that can be controlled with any body part. By shifting weight (x- and y-axis) the disc can tilt in any direction creating a proportional output signal and can also be pushed down in the center (z-axis) to open a menu on a screen for example. When spasms occur it is impossible for users to get stuck on the input device because the disc is flat and can be mounted within a control panel. Body parts coming into contact with the disc would merely slide across the disc without triggering unintentional actions. The sensor presented here is also adaptive and can be adjusted to fit a user’s strength and range of motion. This proposal aims to develop an input device that enables spastic patients to operate sensitive systems safely.

Temporomandibular disorders (TMDs) refer to a group of conditions that affect the temporomandibular joint, causing pain and dysfunction in the jaw joint and related muscles. The diagnosis of TMDs typically involved clinical assessment through operator-based physical examination, self-reported questionnaire and imaging studies. To objectivize the measurement of TMD, this study aims at investigating on the feasibility to use machine-learning algorithms fed with data gathered from low-cost and portable instruments to discriminate the presence of TMD in adult subjects. Through this aim, the experimental protocol involved fifty participants, equally distributed between TMD and healthy subjects, acting as control group. The diagnosis of TMD has been performed by a skilled operator through the typical clinical scale. Participants underwent to a baropodometric analysis by using a pressure matrix and the evaluation of the cervical mobility through inertial sensors. Nine machine-learning algorithms belonging to support vector machine, k-nearest neighbours and decision tree were compared. The k-nearest neighbours based on cosine distance was found as the best performing, achieving performance of 0.94, 0.94 and 0.08 for the accuracy, F1-score and G-index, respectively. These findings open the possibility to use such methodology to support the diagnosis of TMDs in clinical environments.

Hereditary hemochromatosis (HH) is the main genetic cause of iron overload and is regarded as metal-related human toxicosis. HH may result from HFE and non-HFE gene mutations causing hepcidin deficiency or hepcidin resistance. The disorder has a high biochemical penetrance, but a low clinical prevalence. Unfortunately, the majority of patients with HH remain undiagnosed at their disease-curable stage. The main aim of HH therapy is to prevent iron overload in the early-phase disease and elimination of excess iron from the body by phlebotomy in its late stage. Raising global awareness of HH among health professionals, their training to pay attention to early HH signs and symptoms, and strict patient monitoring are critical management strategies for preventing treatment delays, upgrading its efficacy, and improving patient prognosis.

Prediction models in mobility and transportation maintenance systems have been dramatically improved through using machine learning methods. This paper proposes novel machine learning models for an intelligent road inspection. The traditional road inspection systems based on the pavement condition index (PCI) are often associated with the critical safety, energy and cost issues. Alternatively, the proposed models utilize surface deflection data from falling weight deflectometer (FWD) tests to predict the PCI. Machine learning methods are the single multi-layer perceptron (MLP) and radial basis function (RBF) neural networks as well their hybrids, i.e., Levenberg-Marquardt (MLP-LM), scaled conjugate gradient (MLP-SCG), imperialist competitive (RBF-ICA), and genetic algorithms (RBF-GA). Furthermore, the committee machine intelligent systems (CMIS) method was adopted to combine the results and improve the accuracy of the modeling. The results of the analysis have been verified through using four criteria of average percent relative error (APRE), average absolute percent relative error (AAPRE), root mean square error (RMSE), and standard error (SD). The CMIS model outperforms other models with the promising results of APRE=2.3303, AAPRE=11.6768, RMSE=12.0056, and SD=0.0210.

The evolution of human societal dynamics over the course of decades and centuries has led to an ever-increasingly complex digital modern life, one of the hallmark of which is the need for multi-tasking, inclusive of that with media. Is there an empirical mapping between this macroscopic (digital) evolution of the human societal dynamics (in terms of multi-tasking) and the microscopic evolution of the functional molecular units within cells (i.e., proteins) and their manifold cross-talks? Multi-tasking requires a certain degree of intrinsic or adapted flexibility which is as true at the bio-molecular level. Evolutionary diversification of structure-function relationship in proteins emphasizes the functional importance of intrinsically disordered entities (IDPs/IDRs) which are highly dynamic biological soft matters. Multi-functionality is favorably supported by their fluid-like shapes and other new malleable members of the protein family. The new wealth of knowledge coming from recent research on protein intrinsic disorder, fold-switching, moonlighting, hub proteins etc. has given us new insights into protein structure – functional relationship. This has led to a paradigm shift in protein science, clearly diverging from the traditional 'one structure – one function' model applicable to enzyme classes to a more complex understanding of protein functionality. This paradigm shift has caused scientists to delve deeper into the subject, exploring various evolutionary toys and tools to fit the cumulative multi-functional demands in higher organisms. This commentary covers the different evolutionary arsenals to achieve the growing multi-functionality and argues in favor of protein intrinsic disorder as probably the sharpest weapon of all.

Peptides, both natural and synthetic, are well suited for a wide range of purposes and offer versa-tile applications in different fields such as biocatalysts, injectable hydrogels, tumor treatment, and drug delivery. The rising prominence of therapeutic peptides encompasses anticancer, antiviral, antimicrobial, and anti-neurodegenerative properties. The metals Na, K, Mg, Ca, Fe, Mn, Co, Cu, Zn, and Mo are ten of the twenty elements that are considered essential for life. Crucial for under-standing the biological role of metals is the exploration of metal-bound proteins and peptides. Aside from essential metals, there are other, non-essential metals that also interact biologically, exhibiting either therapeutic or toxic effects. Irregularities in metal binding contribute to diseases like Alzheimer’s, neurodegenerative disorders, Wilson's, and Menkes disease. Certain metal com-plexes have potential applications as radiopharmaceuticals. The examination of these complexes was done by preforming UV-Vis, IR, EPR, NMR spectroscopy, and X-ray analysis.

Sustainable continuous cover forestry is defined and analyzed in several ways. The differential equation representing growth of the basal areas of individual trees, motivated by fundamental biological production theory by Lohmander (2017a), is analyzed and extended in different directions. From the solution of the differential equation, the basal area and the tree diameter are obtained as explicit functions of time. The diameter is a strictly increasing function of time. In the absence of competitors, the diameter increment is shown to be a strictly decreasing function of time. Hence, the diameter increment can also be interpreted as a strictly decreasing function of the diameter. Alternative forms of adjustment of the differential equation, with consideration of competition, are defined. If the competition is strong, with large trees in the vicinity of a particular tree, then the basal area increment, and the diameter increment, are reduced. The growth of a large tree is less sensitive than the growth of a small tree, to competition from other trees. Under strong competition, the basal area increment, and the diameter increment, are strictly concave functions of the size of the tree. The unique maximum of the diameter increment occurs at a higher diameter, if the competition increases. In dynamic equilibrium, the tree size frequency distribution is stationary. If natural tree mortality can be avoided via the harvest strategy, the tree size frequency distribution is a function of the size and competition dependent growth function, and the harvest strategy. Empirical tree size frequency data are used to simultaneously estimate parameters of a size and competition dependent growth function and the applied harvest strategy, via nonlinear optimization. The properties of the estimated growth function are consistent with the corresponding properties of the production theoretically motivated hypothetical function, and the properties of the estimated harvest strategy confirm the corresponding hypotheses. The R2 of the nonlinear regression exceeds 0.97. With access to an empirically estimated equilibrium tree size distribution, it is possible to: 1. Estimate size frequency relevant parameters of tree size and competition dependent growth functions for individual trees. 2. Estimate the applied harvest strategy. 3. Explain and reproduce the empirically estimated tree size equilibrium distribution.

Liver X receptors (LXR) are deemed as potential drug targets for atherosclerosis, whereas a role in adipose tissue expansion and its relation to insulin sensitivity remains unclear. To assess the metabolic effects of LXR activation, C57BL/6 mice on a high-fat diet (HFD) were treated with the dual LXRα/β agonist T0901317 (30 mg/kg per day) for 3 weeks. Differentiated 3T3-L1 was used for analysing the effect of T0901317 on glucose uptake.T0901317 reduced fat mass, accompanied by a massive fatty liver and lower adipokine levels in circulation of HFD mice. Increased adipocyte apoptosis and macrophage infiltration were found in epididymal fat of T0901317-treated HFD mice. In addition, T0901317 treatment promoted basal lipolysis, but blunted the anti-lipolytic action of insulin. Furthermore, LXR activation antagonized PPARγ target genes in epididymal fat and PPARγ-PPRE binding activity in 3T3-L1 adipocytes. Although the glucose tolerance was comparable to that in vehicle-treated HFD mice, the insulin tolerance was significantly decreased in T0901317-treated HFD mice, indicating decreased insulin sensitivity by T0901317 administration, and which was further supported by impaired insulin signalling found in epididymal fat and decreased insulin-induced glucose uptake in 3T3-L1 by T0901317administration. These findings reveal that LXR activation impairs adipose expansion which contributes to decreased insulin sensitivity.

Heart failure is a prevalent cardiovascular condition with significant health implications, necessitating effective diagnostic strategies for timely intervention. This study explores the potential of continuous monitoring of non-invasive signals, specifically integrating Photoplethysmogram (PPG) and Electrocardiogram (ECG), for enhancing early detection and diagnosis of heart failure. Leveraging a dataset from the MIMIC-III database, encompassing 682 heart failure patients and 954 controls. Feature selection techniques were used to systematically select key features which were identified for their clinical relevance and significance in capturing cardiovascular dynamics and to reduce computational complexity and to decrease the chance of overfitting the ML algorithms. These features are then utilized to train and evaluate machine learning algorithms, resulting in a model with an impressive accuracy of 98%, sensitivity of 97.60%, specificity of 96.90%, and precision of 97.20%. The integrated approach outperforms single-signal strategies, showcas-ng its potential for early, precise, and non-invasive heart failure diagnosis. Furthermore, the study underscores the significance of continuous monitoring through wearables, emphasizing the benefits of integrating multiple signals for a comprehensive evaluation of cardiovascular health. The proposed approach holds promise for implementation in hardware systems to enable continuous monitoring, aiding in early detection and prevention of critical health conditions.

The ongoing COVID-19 global pandemic is affecting every facet of human lives (e.g., public health, education, economy, transportation, and the environment). This novel pandemic and citywide implemented lockdown measures are affecting virus transmission, people’s travel patterns, and air quality. Many studies have been conducted to predict the COVID-19 diffusion, assess the impacts of the pandemic on human mobility and air quality, and assess the impacts of lockdown measures on viral spread with a range of Machine Learning (ML) techniques. This review study aims to analyze results from past research to understand the interactions among the COVID-19 pandemic, lockdown measures, human mobility, and air quality. The critical review of prior studies indicates that urban form, people's socioeconomic and physical conditions, social cohesion, and social distancing measures significantly affect human mobility and COVID-19 transmission. During the COVID-19 pandemic, many people are inclined to use private transportation for necessary travel purposes to mitigate coronavirus-related health problems. This review study also noticed that COVID-19 related lockdown measures significantly improve air quality by reducing the concentration of air pollutants, which in turn improves the COVID-19 situation by reducing respiratory-related sickness and deaths of the people. It is argued that ML is a powerful, effective, and robust analytic paradigm to handle complex and wicked problems such as a global pandemic. This study also discusses policy implications, which will be helpful for policymakers to take prompt actions to moderate the severity of the pandemic and improve urban environments by adopting data-driven analytic methods.

This study addressed the need for efficient data collection in micro-mobility using low-end hardware, focusing on developing a system capable of handling large real-time data streams. We proposed a novel data collection system that leverages incremental learning techniques, enabling AI-based services for micro-mobility passengers through smartphones. Our approach utilizes 3-axis acceleration sensors integrated into micro-mobility devices, collecting motion data in real-time. This data is processed through an incremental learning pre-processing server, employing the Broad Learning System algorithm, to ensure robust performance in noisy, real-world environments. The use of incremental learning is pivotal, allowing our system to adapt continuously to new data, enhancing the accuracy and relevance of the AI services provided to passengers. This research not only advances the technical capabilities in micro-mobility data handling but also has the potential to enhance the overall passenger experience through improved AI-based services.

The modern supply chain (SC) is growing in terms of data, devices, users, and stakeholders, which introduced new security challenges and threats, especially with the reliance on centralized servers or cloud platforms. In addition, increased trust among system participants exposes the SC to a higher risk of vulnerabilities which require strong security measures. This article proposes a hybrid security framework for SC systems, BC-DRLzSC, that integrates Blockchain (BC) and Deep Reinforcement Learning (DRL) designed to operate in a zero trust (ZT) environment. In particular, we propose a decentralized BC-based approach integrated with smart contracts to manage system participant registration and authentication and to control access to system resources. BC-DRLzSC adopts a ZT architecture to reinforce SC security, which can be achieved with an advocate to verify each entity’s trustworthiness before granting or retaining access to system resources. Incorporating the ZT architecture, with BC and DRL, can potentially and significantly bolster SC system security. DRL is employed to develop a proactive attack detection model that continuously monitors the incoming traffic from authenticated nodes within the network and predicts any malicious actions. Finally, we evaluate the performance of our proposed DRL solution using the NSL-KDD dataset.

Classifying network flow subsequences in an Industrial IoT gateway is an effective method for identifying Industrial IoT faults. This paper proposes a subsequence classification algorithm SSGBUL-IKNN based on unsupervised learning encoding to address the problem of low classification accuracy. Firstly, we built a network module based on unsupervised learning to encode the flow sequence of the Industrial IoT gateway. In the encoding module, a subsequence calibration algorithm controls the increasing error during the coding process. Then, the specific fault type is obtained through an improved KNN classification algorithm based on the indication distance source from the integrated coding sequences converted by multi-dimensional network flow sequences. The test result on three Industrial IoT datasets of a sewage treatment plant shows that the accuracy of SSGBUL-IKNN in this paper exceeds 92%, significantly higher than the algorithm DTW and TSF. It reaches the classification requirements of Industrial IoT fault diagnosis.

Infrared thermography has already been proven to be a significant method in non-destructive evaluation since it gives information with immediacy, rapidity and low cost. However, the thorniest issue for wider application of IRT is the quantification. In this work, we proposed a specific depth quantifying technique by employing the Gated Recurrent Units (GRU) in composite material samples via pulsed thermography (PT). Carbon Fiber Reinforced Polymer(CFRP) embedded with flat bottom holes were designed via Finite Element Method (FEM) modeling in order to precisely control the depth and geometrics of the defects. The GRU model automatically quantified the depth of defects presented in the CFRP material. The proposed method evaluated the accuracy and performance of synthetic CFRP data from FEM for defect depth predictions.

Mobility is a vital welfare indicator which may influence broilers’ daily activities. Classical broiler mobility assessment methods are laborious and cannot provide timely insights into their conditions. Here, we proposed a semi-supervised Deep Learning (DL) model, YOLOv5, combined with Deep Sort algorithm conjoined with our newly proposed algorithm, Neo-Deep Sort, for individual broiler mobility tracking. Initially, 1,650 labeled images from five days were employed to train the YOLOv5 model. Through semi-supervised learning (SSL), this narrowly trained model was then used for pseudo-labeling 2,160 images, of which 2,153 were successfully labeled. Thereafter, the YOLOv5 model was fine-tuned on the newly labeled images. Lastly, the trained YOLOv5 and the Neo-Deep Sort algorithm were applied to detect and track 28 broilers in two pens and categorized them in terms of hourly and daily traveled distances and speeds. SSL helped in increasing the YOLOv5 model’s mean Average Precision (mAP), in detecting birds, from 81% to 98%. As compared with the manually measured covered distances of broilers, the combined model provided individual broiler's hourly moved distances with a validation accuracy of about 80%. Eventually, individual and flock level mobilities were quantified while overcoming the occlusion, false and miss detection issues.

This study focuses on the optimal deployment problem, and determines the optimal size of a military force to send to the battle field. The decision is optimized, based on an objective function, that considers the cost of deployment, the cost of the time it takes to win the battle, and the costs of killed and wounded soldiers with equipment. The cost of deployment is modeled as an explicit function of the number of deployed troops and the value of a victory with access to a free territory, is modeled as a function of the length of the time it takes to win the battle. The cost of lost troops and equipment, is a function of the size of the reduction of these lives and resources. An objective function, based on these values and costs, is optimized, under different parameter assumptions. The battle dynamics is modeled via the Lanchester differential equation system based on the principles of directed fire. First, the deterministic problem is solved analytically, via derivations and comparative statics analysis. General mathematical results are reported, including the directions of changes of the optimal deployment decisions, under the influence of alternative types of parameter changes. Then, the first order optimum condition from the analytical model, in combination with numerically specified parameter values, is used to determine optimal values of the levels of deployment in different situations. A concrete numerical case, based on documented facts from the Battle of Iwo Jima, during WW II, is analyzed, and the optimal US deployment decisions are determined under different assumptions. The known attrition coefficients of both armies, from USA and Japan, and the initial size of the Japanese force, are parameters. The analysis is also based on some parameters without empirical documentation, that are necessary to include to make optimization possible. These parameter values are motivated in the text. The optimal solutions are found via Newton- Raphson iteration. Finally, a stochastic version of the optimal deployment problem is defined. The attrition parameters are considered as stochastic, before the deployment decisions have been made. The attrition parameters of the two armies have the same expected values as in the deterministic analysis, are independent of each other, have correlation zero, and have relative standard deviations of 20%. All possible deployment decisions, with 5000 units intervals, from 0 to 150000 troops, are investigated, and the optimal decisions are selected. The analytical, and the two numerical, methods, all show that the optimal deployment level is a decreasing function of the marginal deployment cost, an increasing function of the marginal cost of the time to win the battle, an increasing function of the marginal cost of killed and wounded soldiers and lost equipment, an increasing function of the initial size of the opposing army, an increasing function of the efficiency of the soldiers in the opposing army and a decreasing function of the efficiency of the soldiers in the deployed army. With stochastic attrition parameters, the stochastic model also shows that the probability to win the battle is an increasing function of the size of the deployed army. When the optimal deployment level is selected, the probability of a victory is usually less than 100%, since it would be too expensive to guarantee a victory with 100% probability. Some of many results of relevance to the Battle of Iwo Jima, are the following: In the deterministic Case 0 analysis, the optimal US deployment level is 66200, the time to win the battle is 30 days and 14000 US soldiers are killed or wounded. If the marginal cost of the time it takes to win a victory doubles, the optimal deployment increases to 75400, the time to win a victory is reduced to 26 days, and less than 12000 soldiers are killed or wounded. In the stochastic Case 0 analysis, the optimal US deployment level is 65000, the expected time to win the battle is 46 days and almost 25000 US soldiers are expected to be killed or wounded. If the cost per killed or wounded soldier increases from 0 to 5 M $US, the optimal deployment level increases to 75000. Then, the victory is expected to appear after 35 days and 19900 US soldiers are expected to be killed or wounded.

Systemic inflammation and coronary microvascular endothelial dysfunction are essential pathophysiological factors in heart failure with preserved ejection fraction (HFpEF) that support the use of statins. The pleiotropic properties of statins, such as anti-inflammatory, antihypertrophic, antifibrotic, and antioxidant effects, are generally accepted and may be beneficial in HF, especially in HFpEF. Numerous observational clinical trials have consistently shown a beneficial prognostic effect of statins in patients with HFpEF, while the results of two larger trials in patients with HFrEF have been controversial. Such differences may be related to a more pronounced impact of the pleiotropic properties of statins on the pathophysiology of HFpEF and pro-inflammatory comorbidities (arterial hypertension, diabetes mellitus, obesity, chronic kidney disease) that are more common in HFpEF. This review discusses the potential mechanisms of statin action that may be beneficial for patients with HFpEF, as well as clinical trials that have evaluated the statin effects on left ventricular diastolic function and clinical outcomes in patients with HFpEF.

According to the cognitive radio (CR) paradigm, the efficient use of the radio spectrum is achieved by performing four main functions: spectral perception, spectral mobility, decision-making, and cooperation. In this work, a multivariable algorithm that considers geographic mobility (GM) is presented. The decision-making process includes a feedback mechanism for the dynamic selection of reservation channels in a wireless network with cognitive capabilities. Geographic mobility plays a crucial role in how radio takes advantage of its environment; however, it has been scarcely explored in the literature. In the present work, geographic mobility tests were carried out involving the interaction of CR and primary users (PU), where a measurement of the latency time of the proposed algorithm called: Algorithm for Decision-Making with Geographic Mobility (ATDeMoGeo) was evaluated and compared with other algorithms such as: Dijkstra's Algorithm, Analytic Hierarchical Process (AHP), Fuzzy Analytic Hierarchical Process (FAHP) and Decision-Making Algorithm with Modified Dijkstra (ATDDiM). It was found that the proposed algorithm is robust and that it considerably reduces the latency time to accurately determine the best communication channels, thanks to the decision-making function implemented to establish which channels the CRs can occupy. For the selection of the best reserve channels, a series of criteria were considered, such as: signal-to-interference plus noise ratio (SINR), bandwidth (BW), probability of channel availability (AP), estimated channel time of availability (ETA) using the random waypoint mobility model (RWPM). These criteria are evaluated for two types of service, i.e., real time (RT) and best effort (BE). For the evaluation and validation of the ATDeMoGeo algorithm, a network with cognitive characteristics in NS-3 was simulated. The simulation scenarios consisted of a base station (BS) with mobile CRs and PUs. Based on the previous criteria, i.e., BW, SINR, AP and ETA, the BS assesses the spectrum occupancy information obtained by the CRs. The results show that the proposed algorithm can be used without problem for the proposed scenarios with higher speed and accuracy for the selection of better communication channels.

Recently, smart mobility intelligent traffic services have become a critical task in Intelligent Transportation Systems (ITS). This involves not only the use of advanced sensors and controllers but also the ability to respond to real-time traffic situations at intersections, alleviate congestion, and generate policies to prevent traffic jams. DRL (Deep Reinforcement Learning) provides a natural framework for processing tasks. In DRL, each intersection can control itself and coordinate with neighbors to achieve optimal network-wide policies. However, comparing approaches remains a challenging task due to the existence of numerous possible configurations. This research performs a critical comparison of various traffic controllers found in the literature. It demonstrates that using a nonlinear approximator for coordination mechanisms and enhancing observability at each intersection are key performance drivers.

The research of object classification and part segmentation is a hot topic in computer vision. A considerable number of studies have been carried out about deep learning on 3D point clouds. However,it is challenging to achieve effective feature learning due to sparsity of point clouds. Recently, a variety of Transformers have been adopted to improve point cloud processing and display great potential. Nevertheless, large numbers of Transformer layers tend to incur huge computational and memory costs. PointNet++ is one of the most influential neural architectures for point cloud understanding. Although the accuracy of PointNet++ has been largely surpassed by recent networks, this does not mean that PointNet++ has no potential.Thus, this paper offer two major contributions that significantly improve PointNet++ performance. Firstly, we introduce a novel contextual feature extraction (CFE) block that significantly enhances the feature extraction capabilities of PointNet++ networks. Secondly, to further enhance feature fusion, we seamlessly integrate a mutual learning (ML) block into the network architecture. By embedding these two innovative blocks within each layer of the network, we not only enrich the network's functionality but also impart it with greater robustness and adaptability. The specific experiments were conducted on the S3DIS (6-fold cross-validation) and Modelnet40 datasets with 86.5% and 92.7% accuracy, respectively, which proved that our model is comparable or even better than most existing methods for classification and segmentation tasks.

Over a billion people around the world are disabled, among them, 253 million are visually impaired or blind, and this number is greatly increasing due to ageing, chronic diseases, poor environment, and health. Despite many proposals, the current devices and systems lack maturity and do not completely fulfill user requirements and satisfaction. Increased research activity in this field is required to encourage the development, commercialization, and widespread acceptance of low-cost and affordable assistive technologies for visual impairment and other disabilities. This paper proposes a novel approach using a LiDAR with a servo motor and an ultrasonic sensor to collect data and predict objects using deep learning for environment perception and navigation. We adopted this approach in a pair of smart glasses, called LidSonic V2.0, to enable the identification of obstacles for the visually impaired. The LidSonic system consists of an Arduino Uno edge computing device integrated into the smart glasses and a smartphone app that transmits data via Bluetooth. Arduino gathers data, operates the sensors on smart glasses, detects obstacles using simple data processing, and provides buzzer feedback to visually impaired users. The smartphone application collects data from Arduino, detects and classifies items in the spatial environment, and gives spoken feedback to the user on the detected objects. In comparison to image processing-based glasses, LidSonic uses far less processing time and energy to classify obstacles using simple LiDAR data, according to several integer measurements. We comprehensively describe the proposed system's hardware and software design, construct their prototype implementations, and test them in real-world environments. Using the open platforms, WEKA and TensorFlow, the entire LidSonic system is built with affordable off-the-shelf sensors and a microcontroller board costing less than $80. Essentially, we provide designs of an inexpensive, miniature, green device that can be built into, or mounted on, any pair of glasses or even a wheelchair to help the visually impaired. Our approach affords faster inference and decision-making using relatively low energy with smaller data sizes as well as faster communications for the edge, fog, and cloud computing.

(1) Background: In this work, a series of benzimidazole derivatives containing colchicine-like and cathechol-like moieties with methyl group substitution in the benzimidazole ring were evaluated for their in vitro antiproliferative, pro-apoptotic and antioxidative activity against highly invasive breast cancer cell line MDA-MB-231 and related impairment of tubulin dynamics; (2) Methods: MTT assay was used to evaluate the antiproliferative activity. In vitro tubulin polymerization assay as well as docking analysis was applied to prove the alterations in tubulin polymerization. Immunofluorescent and DAPI staining reveal the pro-apoptotic potential of benzimidazole derivatives and the effect on tubulin’s dynamics in living cells. The antioxidant activity was evaluated by scavenging of H2O2 and hypochlorite ion and ortho-phenanthroline tests; (3) Results: The compounds containing colchicine-like moiety displayed significant growth inhibitory effect against cancer cell line as was highlighted the role of methyl functional group on the tubulin aggregation and blockage of mitosis. All compounds showed an ability to scavenge H2O2, while the compounds with cathecol-like moiety were more effective against hypochlorite ion and chelation of iron; (4) Conclusions: The benzimidazole derivative containing colchicine-like moiety and methyl group substitution in benzimidazole ring is a potential antiproliferative and microtubule destabilizing agent.

Count data analysis presents unique challenges due to its discrete nature, often exhibiting excessive zeros and overdispersion. To address these complexities, count models, such as Poisson regression and Negative Binomial regression, have been developed, enabling modeling and prediction of count-based phenomena. Additionally, it’s important to notice that zero inflation, a phenomenon commonly observed in count data, requires specialized techniques for robust analysis. This article provides an overview of count data and count models, explores zero inflation, introduces Likelihood Ratio Tests, and explains how the Vuong Test can be used as a model selection criteria. Furthermore, we created a Vuong Test implementation from scratch using the Python programming language. This implementation enhances the accessibility and applicability of the Vuong Test in real-world scenarios, providing a valuable contribution to the academic community, since Python didn’t have an implementation of this statistical test.

Objectives: To assess the short-term impact of a single global stretching session on plantar pressures and lumbar range of motion (RoM) over one week in sedentary university students. Design: A randomised controlled trial with two parallel groups. Participants: Sixty-four university students were randomly assigned to a stretching group or control group. The stretching group received a single session of global stretching and the control group remained seated for the same length of time as the stretching session. Main outcome measures: Lumbar RoM and plantar pressures were assessed before, immediately after, 48 hours after, and 7 days after intervention. Results: Group-by-time interaction was significant for lumbar lateral flexion (p = 0.044), right maximal pressure (p = 0.003), left maximal pressure (p = 0.008), right mean pressure (p = 0.025), left mean pressure (p = 0.002), and maximal pressure minus mean pressure in right foot (p = 0.007). The model with plantar pressures showed a significant difference for group-by-time interaction (p = 0.010).Conclusion: Global stretching seems to counteract the ill-effects of prolonged sitting up to seven days with respect to plantar pressure in standing without improving lumbar ROM

Multimodal remote sensing data classification can enhance the model’s ability to distinguish land features through multimodal data fusion. In this context, how to help models understand the relationship between multimodal data and target tasks is the focus of researchers. Inspired by human feedback learning mechanisms, causal reasoning mechanisms, and knowledge induction mechanisms, this paper integrates causal learning, reinforcement learning, and meta learning into a unified remote sensing data classification framework and proposed the causal meta-reinforcement learning (CMRL). First, based on feedback learning mechanisms, we have overcome the limitations of traditional implicit optimization of fusion features and customized a reinforcement learning environment for multimodal remote sensing data classification tasks. Through feedback interactive learning between agents and the environment, we help them understand the complex relationships between multimodal data and labels, thereby achieving full mining of multimodal complementary information. Second, based on the causal inference mechanism we designed causal distribution prediction action, classification reward, and causal intervention reward, capturing pure causal factors in multimodal data and cutting off false statistical associations between non-causal factors and class labels. Finally, based on the knowledge induction mechanism, we designed a bi-layer optimization mechanism based on meta-learning. By constructing a meta training task and meta validation task simulation model in the generalization scenario of unseen data, we helped the model induce cross-task shared knowledge, thereby improving its generalization ability for unseen multimodal data. The experimental results on multiple sets of multimodal datasets show that the proposed method achieved state-of-the-art performance in multimodal remote sensing data classification tasks.

The new IoT/IoE (internet of things/everythings) paradigm and architecture permits to rethink about the way the Smart City infrastructures are designed and managed, on the other hand a number of problems have to be solved. In terms of mobility the cities that embrace the sensoring era can take advantage of this disruptive technology to improve the quality of life of their citizen, also thanks the rationalization in the use of their resources. In Sii-Mobility, a national smart city project on mobility and transportation, a flexible platform has been designed and here, in this paper, is presented. It permits to setup heterogeneous and complex scenarios that integrate sensors/actuators as IoT/IoE in an overall scenario of Big Data, Machine Learning and Data Analytics. A detailed and complex case-study has been presented to validate the solution in the context of a system that dynamically reverse the traveling direction of a road segment, with all the safety conditions in place. This case study composes several building blocks of the IoT platform, which demonstrate that a flexible and dynamic set-up is possible, supporting off-grid, security, safety, cloud and mixed solutions.

Recent years have witnessed significant advances in reinforcement learning (RL), which has registered remarkable success in solving various sequential decision-making problems in machine learning. Most of the successful RL applications, e.g., the games of Go and Poker, robotics, and autonomous driving, involve the participation of more than one single agent, which naturally fall into the realm of multi-agent RL (MARL), a domain with a relatively long history, and has recently re-emerged due to advances in single-agent RL techniques. Although, typically, the communication protocol between agents is manually specified and not altered during training, recently, some papers have shown signs of trying to emerge a communication between agents on the one hand and, on the other hand, to understand what is exchanged between agents. So, there is a growing body of literature on this topic which includes qualitative and quantitative studies and the ones that apply mixed methods. This study presents the scoping review of the methodological strategies undertaken in a total of 16 research articles. The results present the critical appraisal of quantitative methods in terms of validity and reliability and for qualitative methods considering four trustworthiness factors. In the end, relevant insights are further explored with implications and reflections on how they can benefit one's research in the field.

During public health events, Active Mobility (walking and cycling) plays an important role in securing residents' travel. To enhance the resilience of urban transportation, this article integrates the travel environment elements for walking and cycling and constructs a travel environment for Active Mobility evaluation index system. This article uses survey data from the main urban area of Harbin in the context of the COVID-19 pandemic in May 2022, and combines the Gradient Boosting Decision Tree (GBDT) and Impact-Asymmetry Analysis (IAA) methods to analyze the satisfaction of the travel environment for Active Mobility. It proposes strategies for optimizing the travel environment for Active Mobility, ensuring residents' travel during public health events, guiding them to adopt Active Mobility, and improving urban transportation resilience. This research shows that Active Mobility can enhance urban transportation resilience. In addition, there are differences in resident demand for walking and cycling environments in the travel environment for Active Mobility. Residents are more concerned about the comfort of the walking environment, while they prioritize the convenience of the cycling environment.

Diversity as well as temporal and spatial changes of the proportional abundances of different antibiotics (cycling, mixing or combinations thereof) have been hypothesised to be an effective administrative control strategy in hospitals to reduce the prevalence of antibiotic-resistant pathogens in nosocomial or community-acquired infections. However, a rigorous assessment of the efficacy of these control strategies is lacking. The main purpose here is to present a mathematical framework for the assessment of control stategies from a processual stance. To this end, we adopt diverse measures of heterogeneity and diversity of proportional abundances based on the concept of entropy from other fields and adapt them to the needs in assessing the impact of variations in antibiotic consumption on antibiotic resistance. Thereby, we derive a family of diversity measures whose members exhibit different degrees of complexity. Most important, we extent these measures such that they account for the assessment of temporal changes in heterogeneity including otherwise undetected diversity-invariant permutations of antibiotics consumption and prevalence of resistant pathogens. We apply a correlation analysis for the assessment of associations between changes of heterogeneities on the antibiotics and on the pathogen side. As a showcase, which serves as a proof-of-principle, we apply the derived methods to records of antibiotic consumption and prevalence of antibiotic-resistant germs from University Hospital Dresden. Besides the quantification of heterogeneities of antibiotics consumption and antibiotic resistance, we show that a reduction of prevalence of antibiotic-resistant germs correlates with a temporal change of similarity with respect to the first observation of antibiotics consumption, although heterogeneity remains approximately constant. Although an interventional study is pending, our mathematical framework turns out to be a viable concept for the assessment and optimisation of control strategies intended to reduce antibiotic resistance.

Abstract The aim of our study is to analyse the perception of the families and concerned social workers. The research was conducted in an underprivileged and disadvantaged microregion in North Hungary. The main focus was the perception on the available health, educational, child welfare and social services and supports. The starting point was to enquire the target group’s knowledge of these services. The study examines the extent to which social work is able to provide support to disadvantaged, marginalized families with children, and the way how the dysfunctional operation of the system contributes to the perpetuation of the clients’ life conditions. Analysing the quality of these services and supports is crucial to understand the social mobility chance of the children living in this microregion. The results show that without capability and talent development for the children and given the lack of welfare services, the mobility chance and opportunities of these families are extremely low in Hungary.

The use of unmanned aerial aircrafts (UAVs) is governed by strict regulatory frameworks that prioritize safety. To guarantee safety, it is necessary to acquire and maintain situational awareness (SA) throughout the operation. Existing Canadian regulations require pilots to operate their aircrafts in visual line-of-sight. Therefore, the task of acquiring and maintaining SA primary falls to the pilots. However, the development of aerial transport is entering a new era with the adoption of a highly dynamic and complex system known as advanced air mobility (AAM), which involves UAV operating autonomously beyond visual line-of-sight. SA must therefore be acquired and maintained primarily by each UAV through specific technologies and procedures. In this paper, we review these technologies and procedures in order to decompose the SA of the UAV in the AAM. We then use the system modeling language to provide a high-level structural and behavioral representation of the AAM as a system having UAV as its main entity. In a case study, we analyze one of the flagships UAVs of our industrial partner. Results show that this UAV doesn’t have all the technologies and methodologies necessary to achieve all the identified SA goals identified for the safety of the AAM. This work is a theoretical framework intended to contribute to the realization of the AAM, and we also expect to impact the future design and utilization of UAVs.

Active ageing is defined as the process of optimizing opportunities for physical, social and mental health to enable older people to take an active part in society without discrimination and to enjoy an independent and good quality of life. The World Health Organization assumed this as a process for increasing and maintaining an individual’s participation in activities to enhance his/her quality of life. In this survey, the authors addressed the following question: “Is assistive technology (AT) for mobility contributing to enhancement of lifelong capacity and performance?”. From June 2015 until February 2016, 96 community dwelling adults, AT users for mobility (powered wheelchairs, manual wheelchairs, lower limb prostheses, walkers, crutches and canes), aged 45-97, mean 67.02 +/- 14.24 years old, 56.3% female, were interviewed using the Psychosocial Impact of Assistive Devices Scale (P-PIADS), the Activities and Participation Profile related to Mobility (APPM) and demographics, clinical and questions about AT use and training. The participants’ profiles revealed moderate limitation and restrictions in participation, measured by the APPM (2.03). Most participants showed positive impact of AT; average scores obtained from the P-PIADS subscales were: Self-esteem 0.62, Competency 1.11 and Adaptability 1.10. P-PIADS total was 0.96, with the powered wheelchair users scoring the highest (1.53) and the walker users scoring the lowest (0.73). All subscales and P-PIADS total were positively correlated with the activities and participation profile. There was no relation between age and the psychosocial impact of AT or activities and participation profile. These results encourage the authors to follow these participants up for a lifelong intervention. To accomplish that aim, currently, the protocol is implemented at the AT prescribing centers in Coimbra, Portugal in order to assess the impact of AT on participation in society, one of the domains of the Active Ageing Index, a new analytical tool to help policy makers in developing policies for active and healthy ageing.

The open data market is growing, driven by laws requiring governments to make data publicly available. However, the true value of this market lies in the products and services derived from open data. In Slovenia, the open data market has been growing since 2015, especially in the field of mobility. Platforms such as Avtolog.si facilitate the retrieval of vehicle data via vehicle identification numbers, while tocen.si, ojpp.si, and brezavta.si aggregate mobility data, focusing on sustainable and micromobile public transportation services. These platforms use open government data and private sector open data, and are freely accessible. This study examines the use of open data in the Slovenian mobility applications and similar solutions developed in other countries. By mapping these applications, we gain valuable insights into potential advances in the field, and provide a useful resource for future developers worldwide. By focusing on the socio-economic impact of these innovations, the study identifies methods for evaluating such applications. This approach highlights how transforming open data into user-friendly products and services can deepen our understanding of their broader societal and economic benefits. While open data is valuable in its own right, its full transformative potential is realized through innovative products that support sustainable lifestyles and promote environmentally conscious behavior.

Intelligent fault diagnosis techniques have replaced the time-consuming and unreliable human analysis, increasing the efficiency of fault diagnosis. Deep learning model can improve the accuracy of intelligent fault diagnosis with the help of its multilayer nonlinear mapping ability. This paper has proposed a novel method named Deep Convolutional Neural Networks with Wide First-layer Kernels (WDCNN). The proposed method uses raw vibration signals as input (data augmentation is used to generate more inputs), and uses the wide kernels in first convolutional layer for extracting feature and suppressing high frequency noise. Small convolutional kernels in the preceding layers are used for multilayer nonlinear mapping. AdaBN is implemented to improve the domain adaptation ability of the model. The proposed model addresses the problem that currently, the accuracy of CNN applied to fault diagnosis is not very high. WDCNN can not only achieve 100% classification accuracy on normal signals, but also outperform state of the art DNN model which is based on frequency features under different working load and noisy environment.

Cloud-induced atmospheric extinction and occlusion have a major effect on the effectiveness and quality of telescope observations. Real-time cloud cover distribution and long-term statistical data are essential for astronomical siting and telescope operations. At ground-based astronomical telescope sites, cloud cover distribution is currently analyzed using manual observation methods. However, the main disadvantages of manual observation methods are human subjective, heavy workloads and poor real-time performance. Therefore, a real-time automatic cloud images classification method is desperately needed. This paper presents a new cloud identification method, which is named PSO+XGBoost model by combining eXtreme Gradient Boosting (XGBoost) and Particle Swarm Optimization (PSO). The entire cloud image is divided into 37 sub-regions in order to more precisely identify the distribution of the clouds. 19 features are then extracted, including the sky background, star density, lighting conditions, and subregion grayscale values. The experimental results have shown that the overall classification accuracy of 96.91% and our model is able to outperform several state-of-the-art baseline methods. Our approach achieves high accuracy in comparison with the manual observation methods. Moreover, this method meets telescope real-time scheduling requirements.

This paper analyses the application of deep learning techniques for predicting wave overtopping events in port environments using sea state and weather forecasts as inputs. The study was conducted in the outer port of Punta Langosteira, A Coruña, Spain. A video recording infrastructure was installed to monitor overtopping events from 2015 to 2022, identifying 3709 overtopping events. The data collected was merged with actual and predicted data for the sea state and weather conditions during the overtopping events, creating three datasets. We used these datasets to create several machine learning models to predict whether an overtopping event would occur based on sea state and weather conditions. The final models achieved a high accuracy level during the training and testing stages: 0.81, 0.73, and 0.84 average accuracy during training and 0.67, 0.48, and 0.86 average accuracy during testing, respectively. The results of this study have significant implications for port safety and efficiency, as wave overtopping events can cause disruptions and potential damage. Using deep learning techniques for overtopping prediction can help port managers take preventative measures and optimize operations, ultimately improving safety and helping to minimize the economic impact that overtopping events have on the port's activities.

Recent advances in artificial intelligence combined with behavioral sciences have led to the development of cutting-edge tools for recognizing human emotions based on text, video, audio, and physiological data. However, these data sources are expensive, intrusive, and regulated, unlike plants which have been shown to be sensitive to human steps and sounds. A methodology is proposed to use plants as human emotion detectors. Electrical signals from plants are tracked and labeled based on video data. Labeled data are then used for classification. MLP, biLSTM, MFCC-CNN, MFCC-ResNet, and additionally, Random Forests, 1-Dimensional CNN, and biLSTM without windowing models are set using a grid search algorithm with cross-validation. Finally, best-parameterized models are trained and used with the test set for classification. The performance of this methodology is measured with a case study with 54 participants, who were watching an emotionally charged video, as ground truth their facial emotions were simultaneously measured using face emotion analysis. The Random Forest model shows the best performance, particularly in recognizing high-arousal emotions, achieving an overall weighted accuracy of 55.2% and demonstrating high weighted recall in emotions such as fear 61.0% and happiness 60.4%. The MFCC-ResNet model offers decently balanced results, with Accuracy(MFCC-ResNet)=0.318 and Recall (MFCC-ResNet)=0.324. With the MFCC-ResNet model fear and anger are recognized with 75% and 50% recall respectively. Thus, using plants as an emotion recognition tool seems worth investigating, addressing both cost and privacy concerns.

COVID-19 is the most severe health crisis of the 21st century. COVID-19 presents a threat to almost all countries world-wide. The restriction of human mobility is one of the strategies used to control the transmission of COVID-19. However, it has yet to be determined how effective this restriction is in controlling the rise in COVID-19 cases, particularly in major capital cities such as Jakarta, Indonesia. Using Facebook's mobility data, our study explores the impact of restricting human mobility on COVID-19 case control in Jakarta. Our main contribution is showing how the restriction of human mobility data can give important information about how COVID-19 spreads in different places. We proposed modifying a global regression model into a local regression model by accounting for the spatial and temporal interdependence of COVID-19 transmission across space and time. We applied Bayesian hierarchical Poisson spatiotemporal models with spatially varying regression coefficients. We estimated the regression parameters using an Integrated Nested Laplace Approximation. We found that the local regression model with spatially varying regression coefficients outperforms the global regression model based on DIC, WAIC, MPL, and R2 criteria for model selection. In Jakarta's 44 districts, the impact of human mobility varies significantly. The impacts of human mobility on the log relative risk of COVID-19 range from –4.445 to 2.353. The prevention strategy involving the restriction of human mobility may be beneficial in some districts but ineffective in others. Therefore, a cost-effective strategy had to be adopted.

The key links of face recognition are digital image preprocessing, facial feature extraction and pattern recognition, this article aimed at the current problem of slow speed and low recognition accuracy of face recognition , from the above three key links, on the basic of analyzing the therories of Fractional Differential Masks Operator (FDMO), Principal Component Analysis (PCA) and Support Vector Machine (SVM), design a kind of FDMO+PVA+SVM coupling algorithm that applies to face recognition to improve the speed and accuracy of it. To realize FDMO+PCA+SVM coupling algorithm, first, we should apply FDMO to face image processing binary marginalization, the purpose is getting face contour; Then, we apply PCA to get the feature of face image which is disposed by binary marainalization. At last, we can apply One-Against All of the SVM classifier and LibSVM software package to realize face recognition. Beside, the article with nine different coupling algorithm design four groups of experimental reaults on the ORL face database verified by comparative analysic FDMO+PCA+SVM coupling algorithm in the superiority of face recognition accuracy and speed.

Internal combustion engine (ICE) vehicles contribute significantly to the global warming through their immense quantity of CO2 emissions and are on the way to be replaced by zero emission alternative solutions. Several replacement techniques with scientifically sound performances are proposed for the propulsion equipment including the related supply chains from renewable sources, but they often cannot fulfill the huge demand quantitatively. The paper discusses the quantitative aspects of the real demand with the example of the actual automotive park in Switzerland and analyses different alternatives like conventional EV’s, fuel-cell vehicles or energetic chains based on sustainable fuels like e-methanol or synthetic solar fuels. The analysis comprises energy efficiency considerations.

In this paper, we first discuss the research status and application progress of the finite element method and the smoothed particle method. By analyzing the advantages of the smoothed particle method and the finite element method, a new coupling algorithm, namely FEM-SPH algorithm, is proposed. By the method of comparison, it shows that finite element method and SPH method in the simulation of large deformation problems each have advantages and disadvantages, the finite element method smoothed particle coupling algorithm is effective to achieve the performance of high computational efficiency and can naturally simulate large deformation problems across. In the process of calculation, the large deformation unit can be freely into an algorithm to facilitate the calculation accuracy and efficiency of three methods of numerical simulation. Through the study found, FEM-SPH algorithm not only overcome the defect of smooth particle tensile instability, but also overcomes the problem of low efficiency of finite element computation. To further test the FEM-SPH algorithm has advantages in the practical engineering, we have carried out the actual test to the example of the super high speed collision, concluded that, since the target of most of the computational domain is always finite element, smoothed particle focused only in contact with the projectile and target of local area, particle number is not much, the whole calculation process just ten minutes, computational efficiency has been greatly improved, at the same time in the simulation of large deformation, the advantage is very obvious .This provides a criterion for the actual project, depending on the specific material deformation mode and choose a more appropriate conversion algorithm.

The Eurasian grapevine (Vitis vinifera L.) is the most widely grown horticultural crop in the world and is important for the economy of many countries. In the wine production chain, grape varieties play an important role as they directly influence the authenticity and classification of the product. Identifying the different grape varieties is therefore fundamental for quality control and inspection activities, as well as for regulating production. Currently, ampelography and molecular analysis are the main approaches to identifying grape varieties. However, both methods have limitations. Ampelography is subjective and prone to errors and is experiencing enormous difficulties as ampelographers are increasingly scarce. On the other hand, molecular analyses are very demanding in terms of cost and time. In this scenario, Deep Learning (DL) and Machine Learning (ML) methods have emerged as a classification alternative to deal with the scarcity of ampelographs and avoid molecular analyses. In this study, the most recent and current methods for identifying grapevine varieties using DL classification-based approaches are presented through a systematic literature review. The classification pipeline of the 31 studies found in the literature was described, highlighting its pros and cons. Most of the studies used DL-based models trained with leaf images acquired in a controlled environment at a maximum distance of 1.2 metres to classify grape varieties. In addition, there is a large gap between practical applications and the datasets used: a great lack of varieties, limited data acquired in the field and a lack of tests on plants under adverse conditions. Potential directions for improving this area of research were also presented.

As Artificial Intelligence (AI) technology, particularly Machine Learning algorithms, becomes increasingly ubiquitous, our abilities to understand and interpret AI and machine learning algorithms are becoming increasingly desirable. Visualization has been used as a common tool to view and understand complex machine learning processes. In this paper, we will focus on developing a general framework for the visualization of machine learning models as a scalar valued multi-dimensional function to help users understand how the models behave over different viewing spaces. We first give a formal definition of the visualization problem. Interpolation-based morphing and subspace sampling techniques are applied to generate various renderings through projections and cross-sections of the model space as 3D surfaces or heatmap images. This method will be applied to two real-world datasets and applications: the diagnosis of Alzheimer's Disease (AD) using a human brain networks dataset and a real-world benchmark dataset for predicting home credit default risks. The visualizations show that different machine learning algorithms can behave quite differently under different conditions.

This research focuses on the development of a foot-worn device to assist individuals with limited mobility in walking. The device aims to reduce the risk of accidents by closely moni-toring the wearer's movements and detecting potential hazards. It incorporates sensors, in-cluding the MPU6050 gyro sensor and KY-031 vibration sensor, to track the wearer's walking behavior. In case of abnormalities, such as falls, the device triggers an auditory alert and noti-fies the caregiver via LINE Notify. The system is controlled by the Node MCU ESP8266, enabling seamless integration with the Internet of Things (IoT). The objective of this study is to design an IoT system for medical assistance. The researchers created a prototype of a smart ankle device capable of detecting falls and sending notifications to the user's smartphone. The effectiveness of the notification system was evaluated using the Line Notify application. Re-sults demonstrated a successful detection of falls in 48 out of 50 trials, with two instances of false alarms during normal walking. The overall efficiency of the smart ankle device was 98%. In summary, the proposed smart ankle device demonstrates promising potential for var-ious applications in fall detection and safety alert systems. Further improvements and collab-orations with healthcare experts are recommended to enhance its performance and make it commercially viable. The device's connectivity and responsiveness to IoT systems are vital aspects to be considered. Future research should aim to develop additional features in collab-oration with physiotherapists and healthcare professionals to meet user requirements. The de-vice holds significant benefits in terms of fall detection and safety alerts, and efforts should be made to enhance its durability, robustness, and commercialization prospects.

Probiotic feed additives have attracted considerable research interest in recent years because the effectiveness of probiotics can differ across microbial strains and the supplemented macroorganisms. The present study was conducted on 16 lambs divided into two groups (C - control and E - experimental). The examined lambs were aged 11 days at the beginning of the experiment and 40 days at the end of the experiment. The diet of group E lambs was supplemented with a multi-strain probiotic formulation (Lactobacillus plantarum AMT14, Lactobacillus plantarum AMT4, Lactobacillus rhamnosus AMT15, and Bifidobacterium animalis AMT30), whereas group C lambs did not receive the probiotic additive. At the beginning of the experiment (day 0) and on experimental days 15 and 30, blood was sampled from the jugular vein to determine and compare: phagocytic activity (PHAGOTEST) and oxidative metabolism (PHAGOBURST) of peripheral blood granulocytes and monocytes by flow cytometry. An analysis of the phagocytic activity of granulocytes and monocytes revealed significantly higher levels of phagocytic activity (expressed as the percentage of phagocytic cells and mean fluorescence intensity) in lambs administered the multi-strain probiotic formulation than in the control group. The probiotic feed additive also exerted a positive effect on the oxidative metabolism of both granulocytes and monocytes (expressed as the percentage of oxidative metabolism and mean fluorescence intensity) after stimulation with Escherichia coli bacteria and with PMA (4-phorbol-12-β-myristate-13-acetate).

It is shown by numerical modelling that anisotropic diffusion can compensate and even overcome diffusion broadening - the main limiting factor of devices working at atmospheric pressure. The thickness of ion clouds coming out of the ionisation chamber is reduced ~ 1000 times in the ADMA inlet increasing the resolution. This finding has a great potential that enables construction of a device with resolution close to that of currently available desktop ion separation devices – high pressure mass spectrometers, but with much lower cost of manufacture and with smaller dimensions. Comprehensive numerical modelling along with mathematical analysis of physical concepts enables reduction of the footprint and manufacturing costs. Modelling determined that the resolving power (RP) potential of the ADMA is greater than the RP of currently available on the market devices for the airport security market. The ADMA technology enables very fast detection of threats; at least 100 times faster than currently used in Ion Mobility Spectrometers (IMS). This potentially allows an increase in passenger throughput in airports.

The numerical implementation of the controllers allows the use of very complex algorithms with ease. However, in practice, due to its proven advantages, the PID controller (and its variants) is widely used in industrial control systems as well as in many other applications that require continuous control. Most of the methods for tuning the parameters of PID controllers are based on time-invariant linear models of the processes, which in practice can lead to poor performance of the control system. The paper presents an application of reinforcement learning algorithms in tuning of PID controllers for the control of some classes of continuous nonlinear systems. Tuning the parameters of PID controllers is done with the help of Twin Delayed Deep Deterministic Policy Gradients (TD3) algorithm which presents a series of advantages compared to other similar methods from Machine Learning dedicated to continuous state and action spaces. TD3 algorithm is an off-policy Actor-Critic based method and was used as it does not require a system model. The presented technique is applied for control of a biotechnological system which has a strongly nonlinear dynamic. The proposed tuning method is compared to the classical tuning methods of PID controllers. The performance of the tuning method based on the TD3 algorithm is demonstrated through simulation illustrating the effectiveness of the proposed methodology.

In recent years, advancements in brain science and neuroscience have significantly influenced the field of computer science, particularly in the domain of reinforcement learning (RL). Drawing insights from neurobiology and neuropsychology, researchers have leveraged these findings to develop novel mechanisms for understanding intelligent decision-making processes in the brain. Concurrently, the emergence of quantum computing has opened new frontiers in artificial intelligence, leading to the development of quantum machine learning (QML). This study introduces a novel model that integrates Quantum Spiking Neural Networks (QSNN) and Quantum Long Short-Term Memory (QLSTM) architectures, inspired by the complex workings of the human brain. Specifically designed for reinforcement learning tasks in energy-efficient environments, our approach progresses through two distinct stages mirroring sensory and memory systems. In the initial stage, analogous to the brain’s hypothalamus, low-level information is extracted to emulate sensory data processing patterns. Subsequently, resembling the hippocampus, this information is processed at a higher level, capturing and memorizing correlated patterns. We conduct a comparative analysis of our model against existing quantum models such as Quantum Neural Networks and their classical counterparts, elucidating its unique contributions. Through empirical results, we aim to underscore the effectiveness of our approach in optimizing energy consumption in practical scenarios.

Carbapenem antibiotics are the drug of choice for treating multidrug-resistant bacterial infections. Metallo-beta-lactamases (MBLs) are carbapenemase capable of hydrolyzing nearly all therapeutically available beta-lactam antibiotics. Consequently, a need to assess the frequency and phenotypic resistance phenomena of two MBL genes in diarrheal and urinary tract infections (UTIs). Samples were collected through a cross-sectional study, with MBLs genes detected via PCR. Two hundred twenty eight diarrheal bacteria were isolated from 240 samples. The most predominant pathogens were Escherichia coli (32%) and Klebsiella spp. (7%). Phenotypic resistance to amoxicillin-clavulanic acid, aztreonam, cefuroxime, cefixime, cefepime, imipenem, meropenem, gentamicin, netilmicin, and amikacin was 50.4%, 65.6%, 66.8%, 80.5%, 54.4%, 41.6%, 25.7%, 41.2%, 37.2%, and 42.9%, respectively.  Total 142 UTI pathogens were obtained from 150 urine samples, with Klebsiella spp. (39%) and Escherichia coli (24%) are the major pathogens. Phenotypic resistance to amoxycillin-clavulanic acid, aztreonam, cefuroxime, cefixime, cefepime, imipenem, meropenem, gentamicin, netilmicin, and amikacin was 93.7%, 75.0%, 91.5%, 93.7%, 88.0%, 72.5%, 13.6%, 44.4%, 71.1%, and 43%, respectively.  Twenty four diarrheal isolates carried either blaNDM-1 or blaVIM genes; the overall MBL gene prevalence was 10.5%. Thirty six UTI pathogens carried either blaNDM-1 or blaVIM genes (25.4%). Seven isolates carried both blaNDM-1 and blaVIM genes.  MBL genes exhibited a strong association with phenotypic carbapenem and other beta-lactam antibiotic resistance. Resistance to carbapenems requires active surveillance and stewardship.

Africa was the only continent not to achieve the 2015 Millennium Development Goal of 50% poverty reduction. This paper asks whether Africa will fare better in meeting Sustainable Development Goals (SDGs) addressing poverty and hunger by 2030. To answer this question we examine literature, including our field research published over the last thirteen years. We find that ‘sustainable development’ is a failed concept immersed in the contemporary global economic system that favors growth over ecosystem stability and patriarchal systems of governance that undervalue women’s capacity for sustainability in their care-work as food providers. We examine barriers to women’s farming (climate change, gender bias, limited access to land, technology, finance) and provide examples of women’s innovative strategies for overcoming these barriers in their care practices toward family and community well-being and ecosystem health. We conclude that sustainability is only possible through transformation of thinking away from approaches that value profit over people and ecosystems and toward gender-based approaches for achieving the goals laid out in the SDGs through holistic, integrative systems of ecosystem fit.

The existence of low-cost and accurate tools that can equip the First Responders (FRs) to detect trapped victims and provide insights about their health condition in the aftermath of a disaster, is imperative. To address the problem of detecting trapped victims behind walls or debris, we have developed a tool that exploits an Ultra-Wide Band (UWB) radar sensor for data collection and Machine Learning (ML) algorithms for data analysis. To evaluate the efficacy of our approach, we collected data from nine humans, both in standing and lying down positions. Next, we applied various ML algorithms to the collected dataset for two discrete sub-tasks that are of interest from an FR’s perspective. The first task is the detection of the victim’s presence, where the algorithms attained more than 95% accuracy and F1-Score. The second task is the estimation of the distance between the radar sensor and the victim, where the tool showed an average error of less than 40 cm.

A novel concept of ion separation Anisotropic Diffusion Mobility Analyser (ADMA) with Individual Ion Counter (IIC) was shown by numerical modelling to be able to separate ions with high resolution and ultra-high sensitivity. An ADMA-IIC device has been developed and tested at sheath flow rates below 40 l/min with a number of chemicals relevant to airport security and military applications. The resolving power of the ADMA was observed to be in the range of 40 to 80. These data were close to the resolution obtained in numerical modelling predictions. It is greater than or comparable with the RP of currently available on-the-market devices for airport security and other applications. It was also confirmed that the ADMA technology enables very fast detection of analytes, at least 100 times faster than ion mobility spectrometers. It was shown that Brownian diffusion can be controlled and even overpowered by generating highly anisotropic diffusion in the ADMA device. The ultimate sensitivity of single-ion detection below the ppq range has been demonstrated.

In this paper, we propose an imagined speech-based brain wave pattern recognition using deep learning. Multiple features were extracted concurrently from eight-channel Electroencephalography (EEG) signals. To obtain classifiable EEG data with fewer number of sensors, we placed the EEG sensors on carefully selected spots on the scalp. To decrease the dimensions and complexity of the EEG dataset and to avoid overfitting during the deep learning algorithm, we utilized the wavelet scattering transformation. A low-cost 8-channel EEG headset was used with MATLAB 2023a to acquire the EEG data. The Long-Short Term Memory Recurrent Neural Network (LSTM-RNN) was used to decode the identified EEG signals into four audio commands: Up, Down, Left, and Right. Wavelet scattering transformation was applied to extract the most stable features by passing the EEG dataset through a series of filtration processes. Filtration has been implemented for each individual command in the EEG datasets. The proposed imagined speech-based brain wave pattern recognition approach achieved a 92.50% overall classification accuracy. This accuracy is promising for designing a trustworthy imagined speech-based Brain-Computer Interface (BCI) future real-time systems. For better evaluation of the classification performance, other metrics were considered, and we obtained 92.74%, 92.50% and 92.62% for precision, recall, and F1-score, respectively.

The population’s mobility in urban areas is a necessary variable in the modeling of risk scenarios caused by atmospheric contamination. The inclusion of this concept makes static models more dynamic while considering people within a city to be an entity with complex mobility processes. We propose a conceptual and methodological tool to make the representation of the social, economic and territorial components, as well as the patterns in the population´s mobility to delimitate risk areas for human health by exposure of contaminants. In the volatile organic compounds (VOC), benzene, ethylbenzene, toluene and xylene (BTEX) are amongst the most dominant substances in fugitive vapor emissions in gas stations (GS). In urban areas, the exposure to BTEX by residential proximity and proximity to other facilities, which cause intra-urban agglomeration, can impact and affect human health. This model seeks to facilitate the focalization, identification and prioritization of risk areas by BTEX environmental contamination. This article goes beyond de conceptual framework. It suggests methodological and instrumental aspects to be applied in other cities. The government agencies must consider these results when establishing rules, permissions and procedures to reduce environmental pollution for managing the risk in a complex urban environment.

Background and objectives: Patients with multiple sclerosis (MS) have many potential factors (spasticity, immobilization, glucocorticoids use) which can deteriorate the anthropometrical status and body composition and may have the potential impact on the functional mobility and basic motor skills improvement after physiotherapy. The aim of the study was to assess the functional mobility and basic motor skills in patients with MS and to correlate them with disability and anthropometrical status and body composition parameters. Materials and Methods: Timed Up-and-Go test (TUG), and six-minute walk test (6MWT) were performed in 36 patients with MS before and after 4 weeks of physiotherapy. Body mass index (BMI), waist to height ratio (W/HtR), and waist-to-hip ratio (WHR) were assessed in this group. Body composition was evaluated by bioelectrical impedance analysis (BIA) and fat mass (FAT), fat free mass (FFM), total body water (TBW) and predicted muscle mass (PMM) were expressed as percentage of body mass. Clinical status was assessed by EDSS and AI scales. Results: After physiotherapy, there was a significant improvement in functional mobility and basic motor skills assessed by total distance in 6MWT (p<0.001) and in TUG trials (p<0.001). Positive significant correlations were found between the results obtained in both tests (either before and after physiotherapy) vs. FFM, TBW and PMM, whilst worse results in functional mobility and basic motor skills correlated significantly with higher WHtR, WHR and FAT (p<0.05). Clinical status (EDSS) were significantly related to the WHtR and body composition parameters with the same manner as the results in the either 6MWT and TUG. However, there were no significant relationships between BMI vs. either clinical status (EDSS, AI) and functional mobility tests results in patients with MS. Conclusions: Functional mobility and basic motor skills may be significantly improved during the physiotherapy, but they are related to the anthropometrical status and body composition of MS patients. Moreover, disability status is also significantly related to this parameters. Body composition deterioration seems to be the important target for the therapeutic intervention in MS patients. For proper nutritional status assessment in patients with MS, body composition analysis or WHtR instead BMI should to be used.

This article presents a review of current advances and future prospects in the field of forecasting renewable energy generation using machine learning (ML) and deep learning (DL) techniques. With the increasing penetration of renewable energy sources (RES) into the electricity grid, accurate forecasting of their generation becomes crucial for efficient grid operation and energy management. Traditional forecasting methods have limitations, and thus ML and DL algorithms have gained popularity due to their ability to learn complex relationships from data and provide accurate predictions. This paper reviews the different approaches and models that have been used for renewable energy forecasting and discusses their strengths and limitations. It also highlights the challenges and future research directions in the field, such as dealing with uncertainty and variability in renewable energy generation, data availability, and model interpretability. Finally, this paper emphasizes the importance of developing robust and accurate renewable energy forecasting models to enable the integration of RES into the electricity grid and facilitate the transition towards a sustainable energy future.

Amid escalating urbanization, devising rational commercial space layouts is a critical challenge. Leveraging machine learning, this study uses a Back-propagation (BP) neural network to optimize commercial spaces in Weinan City's central urban area. The results indicate an increased number of commercial facilities with a trend of multi-centered agglomeration and outward expansion. Based on these findings, we propose a strategic framework for rational commercial space development emphasizing aggregation centers, development axes, and spatial guidelines. This strategy provides valuable insights for urban planners in small and medium-sized cities in the Yellow River Basin and metropolitan areas, ultimately showcasing the power of machine learning in enhancing urban planning.

Continuous greenhouse gas emissions are causing global warming and impacting the habitats of many animals. Researchers in the field of electric power are making efforts to mitigate this situation. Operating and maintaining the power grid in an economic, low-carbon, and stable is challenging. To address the issue, we propose a grid dispatching technique that combines prediction technology, reinforcement learning, and optimization technology. Prediction technology can forecast future power demand and solar power generation, while reinforcement learning and optimization technology can make charging and discharging decisions for energy storage devices based on current and future grid conditions. In the power system, the aggregation of distributed energy resources increases uncertainty, particularly due to the fluctuating generation of renewable energy. This requires the use of advanced predictive control techniques to ensure long-term economic and decarbonization goals. In this paper, we present a real-time dispatching framework that integrates deep learning-based prediction, reinforcement learning-based decision-making, and stochastic optimization techniques. The framework can rapidly adapt to target uncertainty caused by various factors in real-time data distribution and control processes. The proposed framework achieved global Champion in the NeurIPS Challenge 2022 competition and demonstrated its effectiveness in practical scenarios of intelligent building energy management.

Epilepsy is a common neurological condition, typically diagnosed using Electroencephalogram (EEG). Large scale EEG datasets have recently been made publicly available, allowing the use of advanced Machine Learning (ML) algorithms to analyze EEG patterns associated with epilepsy. While most existing studies focus on identifying seizures in the EEG, few have tried to identify preictal EEG segments. Identifying preictal EEG segments are not only useful in developing early warning systems but also helps inform the course of treatment for the patient. In this study, we propose to represent EEG segments as images, instead of time-series data, and identify preictal EEG segments using a preexisting ML algorithm (YOLOv8) designed for image processing. Multiplexed images (containing the original EEG signal represented on a 2D grid, kurtosis, and spectral entropy) achieve the best accuracy of 95.75% on the dataset while images just containing the EEG signal result in an accuracy of 91.25%. Using only spectrograms, generated from the original EEG signal, results in an accuracy of 90.15%.

(1) The incidence of ankyloglossia ranges from 0.02 to 10.7%. The literature describes the effect of ankyloglossia on selected dysfunctions of the stomatognathic system, however no studies could be found reporting the influence of ankyloglossia on the occurrence of several disorders in a group of subjects. The aim of the present study was to assess the effect of lingual frenulum on swallowing, speech, occlusion, and periodontal status; (2) Methods: The subjects were 172 patients, 86 with ankyloglossia (study group) and 86 with normal tongue frenulum (control group). In all subjects, the length of tongue frenulum, the type of swallowing, tongue mobility, occlusion, periodontal status and speech abnormalities were assessed; (3) Results: All subjects from the control group and all those with mild ankyloglossia showed normal tongue mobility. A limited tongue mobility was found in 29.4% subject with moderate and in 70.6% subjects with severe ankyloglossia. Rhotacism was observed in 21.3% subjects with normal frenulum, in 2.1% with mild, 38.3% with moderate, and 38.3% with severe ankyloglossia. Malocclusion or crowding was diagnosed in subjects with mild, moderate and severe ankyloglossia in 7.4%, 33.9% and 20.7% subjects (total 62%), respectively, whereas in the control group - in 21.6% subjects. No abnormalities in the periodontium in the area of the lingual surfaces of the crowns of the lower central incisors were found in any of the examined persons. Among patients with infantile type of swallowing 24.4% had a normal length of the tongue frenulum, 11.1% - mild, 28.9% - moderate, and 35.6 - severe ankyloglossia. Among patients presenting a mature type of swallowing 58.7% had a normal length of the frenulum; (4) Conclusions: 1.A shortened tongue frenulum correlates with “infantile swallowing pattern”. 2. Moderate or severe ankyloglossia significantly limits tongue mobility. 3. Short tongue frenulum is related to speech disorders.

Australian regional areas are now receiving significant numbers of migrants from the African continent. Predominantly Anglo-Saxon communities perceive these ‘newcomers’ as physically and culturally different. Asking, however, how African migrants themselves construct relationships with local communities and build a sense of belonging in regional and rural areas is a very different question. This paper explores South Sudanese migrants’experiences conceptualising their sense of belonging in a small county town: Castlemaine, Victoria. Focus group discussions show that even with the welcoming atmosphere and support from the local community, South Sudanese migrants are still attracted to metropolitan environments that have greater diversity, feeling more at home in such settings. Using the theoretical background of a stranger, this paper argues the cities allow strangers be un-noticed letting them feel at ‘home’. Findings from the study show settings with greater diversity encourage negotiating difference openly and easing power imbalances among different groups.Finally, the locality of Castlemaine, within easy commuting distance to metropolitan Melbourne and suburbs, is considered in relation to hypermobility reducing the capacity to construct ‘bridging capital’ within such local communities.

One of the most rapidly advancing areas of deep learning research aims at creating models that learn to disentangle the latent factors of variation from a data distribution. However, modeling joint probability mass functions is usually prohibitive, which motivates the use of conditional models assuming that some information is given as input. In the domain of numerical cognition, deep learning architectures have successfully demonstrated that approximate numerosity representations can emerge in multi-layer networks that build latent representations of a set of images with a varying number of items. However, existing models have focused on tasks requiring to conditionally estimate numerosity information from a given image. Here we focus on a set of much more challenging tasks, which require to conditionally generate synthetic images containing a given number of items. We show that attention-based architectures operating at the pixel level can learn to produce well-formed images approximately containing a specific number of items, even when the target numerosity was not present in the training distribution.

Detection of subsurface archaeological remains using a range of remote sensing methods, poses several challenges until today. Recent studies regarding the detection of archaeological proxies like those of cropmarks highlight the complexity of the phenomenon. In this work we present three different methods, and associated indices, for identifying stressed reflectance signatures indicating buried archaeological remains, based on a dataset of measured ground spectroradiometric reflectance. Several spectral profiles between the visible and near infrared part of the spectrum, were taken over a controlled environment in Cyprus during the 2011-2012 and are re-used in this study. The first two (spectral) methods are based on a suitable analysis of the spectral signatures in (1) the visible part of the spectrum, and in particular in the neighborhood of 570 nm, and (2) the red edge-near infrared part of the spectrum, in the neighborhood of 730 nm. Machine learning (decision trees) allows for the deduction of suitable wavelengths to focus on, in order to formulate the proposed indices and the associated classification criteria (decision boundaries) that can enhance the detection probability of stressed vegetation. Noise in the signal is taken into account by simulating reflectance signatures perturbed by white noise. Applying decision tree classification on the ensemble of simulations and basic statistical analysis we refine the formulation of the indices and criteria for the noisy signatures. The success rate of the proposed methods is over 90%. The third method rests on the estimation of vegetation/canopy reflectance parameters through inversion of the physical-based PROSAIL reflectance model and the associated classification through machine learning methods. The obtained results provide further insights into the formation of stress vegetation that occurred due to the presence of shallow buried archaeological remains, which are well aligned with physical-based models and existing empirical knowledge. To the best of the authors' knowledge, this is the first study demonstrating the usefulness of radiative transfer models such as PROSAIL for understanding the formation of cropmarks. Similar studies can support future research directions towards the development of regional remote sensing methods and algorithms if systematic observations are adequately dispersed in space and time.

Objective The aim of this study was to examine the impact of a modern lifestyle on college female students' health, specifically focusing on their hip and knee joint mobility. The objective of this study was to assess the influence of hydraulic resistance training with the self-myofascial release technique on improving joint mobility in female college students. The training also aimed to compare the effectiveness of hydraulic resistance exercise with and without the self-myofascial release technique on hip and knee joint mobility.Methods The study used a randomized controlled trial design to recruit 30 female college students aged 18-25 through campus advertisements and announcements. Medical conditions or injuries that might have affected participation was screened. Participants were indiscriminately allocated to Group A (Hydraulic Resistance Training with Self-Myofascial Technique) or Group B (Hydraulic Resistance Training without Self-Myofascial Technique). The baseline assessments included joint range of motion (ROM) measurements using a goniometer. Certified trainers supervised the training sessions, and the data were analyzed using SD and mean using SPSS. ResultsThis study aimed to evaluate the impact of hydraulic resistance training with self-myofascial release on hip and knee joint mobility in female college students. The results showed that both groups showed improved hip and knee flexion with and without the self-myofascial release technique. However, the Group A using the self-myofascial release technique (Group A) showed a more significant enhancement, as indicated by the smaller p value compared to Group B. It has been suggested that the self-myofascial release technique may improve hip and knee joint mobility. ConclusionThis study concluded that Hydraulic Resistance Training with Self-Myofascial Release (HSMR) could improve hip and knee joint mobility among female college students. These findings suggest that integrating the self-myofascial release technique into training regimens can improve joint mobility. However, further research with larger sample sizes and extended intervention periods was needed to understand the long-term effects and sustainability of these improvements.

Cross-cultural mobility is a phenomenon that is increasingly growing, and the resulting stress has become a severe health issue. Thus, we conducted a systematic review of articles reporting research on stress measures of cross-cultural mobility or acculturative stress, emphasizing its internal structure. We adopted the PRISMA procedures for scoping reviews (e.g., searching articles in databases), resulting in the inclusion 20 articles in the final analysis that present evidence of validity based on the internal structure of 16 measures. The most common factors identified were related to cultural stressors, language stressors, and discrimination stressors. After analyzing a cross-cultural mobility stress concept implicit in the definitions used in the articles, we found that most measures of acculturative stress did not evaluate it according to the Stress and Coping Model of Lazarus and Folkman. Most measures only focused on part of the phenomena (some estimated the stressors, others the coping strategies). Few took into account the physiological and psychological responses to internal or external stressors, and even fewer considered its positive aspects (eustress). Consequently, it is pivotal to develop measures that take into account the multiple dimensions of the cross-cultural mobility stress. Other results (e.g., validity evidence of the measures) and limitations of this systematic scoping review are presented and discussed.

Charcot-Marie-Tooth (CMT) disease is the most commonly inherited neurological disorder, defined by progressive deterioration of the peripheral nerves. Clinical manifestations of CMT mutations are typically limited to peripheral neurons, the longest cells in the body. Currently, mutations in at least 80 different genes are associated with CMT and new mutations are regularly being discovered. A large portion of the proteins mutated in axonal CMT have documented roles in mitochondrial mobility. This suggests that trafficking defects may be a common underlying mechanism in CMT. This review will focus on the potential role of altered mitochondrial mobility in the pathogenesis of axonal CMT, highlighting the challenges and opportunities to this “impaired mobility” model of the disease.

In the era of mounting water scarcity, particularly in arid regions, the agricultural sector is striving to optimize the water resource management practices. Treated wastewater (TWW) has emerged as a viable alternative to freshwater for irrigation, offering a sustainable solution to water conservation. However, ensuring the safety and quality of TWW is paramount to safeguard for both crop health and environmental integrity. Electrical conductivity (EC), a critical factor in assessing TWW suitability for irrigation, can significantly impact crop yields and soil health since it is directly linked to the concentration of dissolved salts and ions. Therefore, this study delves into the development of advanced predictive models for EC assessment by employing supervised machine learning (ML) techniques like the Support Vector Regression (SVR), Adaptive Network-based Fuzzy Inference System (ANFIS), and Multiple Linear Regression (MLR). The TWW samples collected from Al-Qatif area, Saudi Arabia were assessed in the lab through a sensor-based real-time monitoring system integrated with Internet of Things (IoT) network and a multiprobe device. The key water quality parameters assessed involved, temperature (T), pH, Oxidation Reduction Potential (ORP), Resistivity (RES), Total Dissolved Solids (TDS), Salinity and Turbidity which served as the foundation for these models, given their profound influence on and their anticipated impact on EC levels. Following feature selection, two distinct model combinations were identified for the SVR, ANFIS and MLR models. Furthermore, to evaluate prediction performance, four statistical criteria, including coefficient of determination (R²), correlation coefficient (R), mean square error (MSE), and root mean square error (RMSE), were employed. Overall, the comparative performance results proved that ANFIS-M2 indicated the strongest predictive capability with the R² value of 0.99572 and 0.75145 and the RMSE values of 0.00965 and 0.01134, respectively in both calibration and verification stages.

Globalization, knowledge economy, information technology advancements, and the rise of learning societies contribute to the concept of a learning city. The study examines the economic indicators of Yazd city, Iran, in the context of learning city development. A descriptive-analytical approach with a survey method and cluster sampling was employed. Data analysis involved Kolmogorov-Smirnov normality test, single-sample T-test, simple linear regression, and Kendall's W test. The normality test confirmed data normality. The T-test indicated that experts perceived the current state of most variables in Yazd as undesirable. Regression analysis revealed a significant positive association between the economic index and independent variables. Kendall's W test prioritized areas based on economic indicators, with the top 7 and bottom 5 areas identified for focused interventions. The study emphasizes the need to prioritize areas within Yazd based on their economic indicators. This prioritization informs strategies for enhancing social and legal aspects of Yazd's transformation into a learning city. Further research should explore effective methods to cultivate a full-fledged learning environment in the city.

Accurate diagnosis for the 400 million people with rare diseases is critical for healthcare decisions, prognosis, understanding disease mechanisms, and identification of treatments. Despite advances in genome sequencing, barriers such as high interpretation costs, diagnostic expertise, throughput associated delays, and uncertain variant classifications persist, with demand exceeding capacity. Many variant classification methods focus narrowly on specific consequences, leading to the use of complex integrative pipelines that often overlook transcript variability and lack prediction transparency. To overcome these limitations, we introduce DITTO. This transparent, transcript-aware machine-learning method demonstrates superior overall performance in accuracy, recall, and precision when compared to existing tools. DITTO is publicly available at https://github.com/uab-cgds-worthey/DITTO

Vertical Indoor Farming (VIF) with hydroponics offers a promising perspective for sustainable food production. Intelligent control of VIF system components plays a key role in reducing operating costs and increasing crop yields. Modern machine vision (MV) systems use Deep Learning (DL) in combination with camera systems for various tasks in agriculture, such as disease and nutrient deficiency detection, and flower and fruit identification and classification for pollination and harvesting. This study presents the applicability of MV technology with DL modelling to detect the growth stages of chilli plants using YOLOv8 networks. The influence of different bird’s eye and side view datasets and different YOLOv8 architectures was analysed. To generate the image data for training and testing the YOLO models, chilli plants were grown in a hydroponic environment and imaged throughout their life cycle using four camera systems. The growth stages were divided into growing, flowering and fruiting classes. All trained YOLOv8 models showed reliable identification of growth stages with high accuracy. The results indicate that models trained with data from both views show better generalisation. YOLO’s middle architecture achieved the best performance.

Analysis of land use/land cover (LULC) in the catchment areas is the first action toward safeguarding the freshwater resources. The LULC information in the watershed has gained popularity in the natural science field as it helps water resource managers and environmental health specialists develop natural resource conservation strategies based on available quantitative information. Thus, remote sensing is the cornerstone in addressing environmental-related issues at the catchment level. In this study, the performance of four machine learning algorithms (MLAs), such as Random Forests (RF), Support Vector Machine (SVM), Artificial Neural Networks (ANN), and Naïve Bayes (NB) was investigated to classify the catchment into nine relevant classes of the undulating watershed landscape using Landsat 8 Operational Land Imager (L8-OLI) imagery. The assessment of the MLAs were based on the visual inspection of the analyst and the commonly used assessment metrics, such as user’s accuracy (UA), producers’ accuracy (PA), overall accuracy (OA), and kappa coefficient. The MLAs produced good results, where RF (OA= 97.02%, Kappa= 0.96), SVM (OA= 89.74 %, Kappa= 0.88), ANN (OA= 87%, Kappa= 0.86), and NB (OA= 68.64 Kappa= 0.58). The results show the outstanding performance of the RF model over SVM and ANN with a small margin. While NB yielded satisfactory results, which could be primarily influenced by its sensitivity to limited training samples. In contrast, the robust performance of RF could be due to an ability to classify high-dimensional data with limited training data.

Background High Mobility Group Box-1 (HMGB-1) is implicated in the pathogenesis of thrombosis and cancer. In the present study, we aimed to evaluate its potential role as a diagnostic biomarker of portal vein thrombosis (PVT) among patients with hepatocellular carcinoma (HCC). Methods The study population included N=100 prospectively recruited patients with a novel diagnosis of HCC. We compared circulating HMGB-1 levels between 34 healthy controls, HCC patients with PVT (N=22), and HCC patients without PVT (N=78). Results HCC patients without PVT showed significantly higher median HMGB-1 serum levels (8.2 [5.5-13.1] ng/ml) than those observed in the case of HCC with PVT (5.5 [4.4-8.5] ng/ml; p=0.012) and in healthy controls (4.1 [3.1-8.2] ng/ml; p&lt;0.001). Among HCC patients, at univariate analysis, the presence of PVT was associated with higher median age (p=0.036), larger major cancer node diameter (p&lt;0.001), and lower HMGB-1 serum level (p=0.012). At multivariate analysis, the presence of PVT maintained a positive association with major node diameter p=0.001) and an inverse association with serum HMGB-1 levels (p=0.003). Conclusions These findings indicate that serum HMGB-1 bears an inverse association with PVT complicating HCC at the time of diagnosis and suggest that serum HMGB-1 depletion may mark PVT development in cirrhotic patients with HCC.

In this study, GC–IMS was used to analyze the volatile component and flavor profiles of Crassostrea gigas individuals of different ploidy and gender. Principal component analysis was used to explore overall differences in flavor profiles and a total of 54 volatile compounds were identified. The total volatile flavor contents in edible parts of tetraploid oysters were significantly higher than in diploid and triploid oysters. The concentrations of ethyl (E)-2-butenoate and 1-penten-3-ol were significantly higher of triploid oysters than in diploid and tetraploid oysters. In addition, the volatile compounds propanoic acid, ethyl propanoate, 1-butanol, butanal, and 2-ethyl furan were significantly higher in females than in males. The volatile compounds p-methyl anisole, 3-octanone, 3-octanone, and (E)-2-heptenal were present in higher levels in male than in female oysters. Overall, different ploidy and gender of oysters were being presented with different sensory characteristics, providing new insights for understanding the flavor characteristics of oysters.

This paper presents an innovative multi-agent, data-driven reinforcement learning (RL) approach to develop and utilize the thermal equivalent network model that represents the motor's thermal dynamics. A multi-agent reinforcement learning is designed and trained to adjust the model parameters using data from several motor driving cycles. To ensure the incoming driving cycle matches the historical data before employing the pre-trained RL agents, offline statistical analysis and clustering techniques are developed and used. Numerical simulations highlighted the RL agent's ability to develop strategies that effectively address the variability of driving cycles. The proposed RL framework showed its capability to accurately reflect the motor's thermal behavior under various driving conditions.

Timely and accurate information on tree species is crucial for the sustainable management of natural resources, forest inventory, biodiversity detection, and carbon stock calculation. The advancement of remote sensing technology and artificial intelligence has facilitated the acquisition and analysis of remote sensing data, resulting in more precise and effective classification of tree species. Multimodal remote sensing data and deep learning seem to be the current tree species classification research mainstream, whether or not. The current review on the remote sensing data and deep learning tree species classification methods perspectives to analyze the unimodal and multimodal remote sensing data and classification methods in this realm is missing. To bridge the gap, we search for major trends in the remote sensing data and tree species classification methods, provide a detailed overview of classic deep learning-based methods for tree species classification, and discuss the limitations.

Deep learning heavily relies on statistical correlations to drive artificial intelligence (AI) innovations, particularly in computer vision applications like autonomous driving and robotics. However, despite providing a solid foundation for deep learning, these statistical correlations can be vulnerable to unforeseen and uncontrolled factors. The lack of prior knowledge guidance can result in spurious correlations, introducing confounding factors and affecting the model's robustness. To address this challenge, recent research efforts have focused on integrating causal theory into deep learning methodologies. By modelling the inherent and unbiased causal structure, causal theory can potentially mitigate the impact of spurious correlations effectively. Hence, this paper explores the basics of causal methodologies in image classification.

Structures inevitably suffer damages after an earthquake, with their severity ranging from minimal damages to non-structural elements to partial or even total collapse, possibly with loss of human lives. Thus, it is essential for engineers to understand the crucial factors that drive a structure towards suffering higher degrees of damage, so that preventative measures can be taken. In the present study, we focus on three well-known damage thresholds, namely Collapse Limit State, Ultimate Limit State and Serviceability Limit State and analyze which of the features obtained via Rapid Visual Screening, determine whether or not a given structure will cross that threshold. To this end, we use Machine Learning to perform binary classification for each damage threshold, as well as Explainability via SHAP values (acronym for SHapley Additive exPlanations) to quantify the effect of each parameter. The quantitative results obtained demonstrate the potential applicability of ML methods to re-calibrate the computation of structural vulnerability indices using data from recent earthquakes.

Heavy rains have created significant threats to human health and life. Floods and other natural disasters, which have a global impact annually, can be attributed to extended durations of intense precipitation. Accurate rainfall predictions are crucial in nations such as Bangladesh, where agriculture is the predominant occupation. The efficiency of machine learning (ML) methods is enhanced by the non-linearity of rainfall, surpassing the effectiveness of other alternative ways. Machine learning techniques show that individual classifiers exhibit worse accuracy than ensemble learning (EL) methodologies. Ensemble Learning techniques are utilized for rainfall prediction and estimating rainfall quantity and daily average temperature to enhance comprehension of the diverse Machine Learning algorithms. This research implements the machine learning techniques and ensemble-based classifier to predict the rainfall occurrence, along with the machine learning regressor models and ensemble-based regressor for the rainfall amount prediction and daily average temperature prediction, using Bangladesh Weather Dataset. The results of the machine learning and ensemble-based models are compared using the Accuracy and F1 score for rainfall occurrence prediction. In contrast, MAE and RMSE evaluation metrics are used for ensemble regressor and regression algorithms for the rainfall amount and daily average temperature prediction. With an accuracy of 83.41% and a recall of 78.17%, the Ensemble Classifier is the best at predicting when it will rain, but its precision of 51.16% stands in for the lowest. The Ensemble Regression model outperforms Linear Regression, Random Forest, and SVR in rainfall amount prediction, with the lowest MAE of 0.36 and RMSE of 0.90. The Ensemble Regression provides the most precise results for daily average temperature prediction with the lowest MAE 0.42 and RMSE 0.54 highlighting its superiority over the other regression models in forecasting temperature with less error. Ensemble approaches consistently lead task performance metrics.

The proposed method deals with the problem of data privacy and sharing when processing personal mobility tracking data. Previous methods concentrate on producing highly detailed data on short-term and restricted areas, e.g. for autonomous driving scenarios. Another possibility consists of city-wide scales and beyond, that are used to predict general traffic flows. The presented approach takes the tracked mobility behavior of individuals to create coherent new mobility data that reflects the long-term mobility behavior of the person, guaranteeing location persistency and sound embedding within the point-of-interest structure of the observed area. After an analysis and clustering step with the original data, the area is distributed into a geospatial grid structure (H3 is used here), and the neighborhood relationships between the grids are interpreted as a graph. A feed-forward-autoencoder and a graph encoding-decoding network generate a latent space representation of the area. The original clustered data is associated with their respective H3 grids. With a greedy algorithm approach and concerning privacy strategies, new combinations of grids are top-level patterns for individual mobility behavior. Concrete locations are found and connected within the grids based on the original data. The described method is then applied to a study with 1000 participants from the city of Munich in Germany, and the results are described, showing the application of the approach in generating synthetic data, enabling further research on individual mobility behavior and patterns. The result is a sharable dataset on the same abstraction level as the input data, which makes it interesting, particularly for machine learning applications.

Mobility as a Service (MaaS) is an innovative transport concept, anticipated to provide travelers with different kinds of travel services, more sustainable than a private car, in a simpler, packaged way. It combines different transport modes to offer a tailored mobility package, like a monthly mobile phone contract. The rapid development of intelligent transportation system and the shared economy has speeded up the development of MaaS in these years. In this paper, we aim at classifying the existing research on MaaS and the characteristics of MaaS into different categories, in order to answer the following questions after reviewing the existing literature: What is MaaS? Who are the main actors in MaaS? How can MaaS be implemented? Why should it be implemented? Where will MaaS end up in this wave of disruption? When we talk about MaaS, what are we focusing on? What is the future leading frequency of MaaS? Finally, based on the existing literature, we envision the leading future of MaaS.

Although Eulerian approaches are standard in computational acoustics, they are less effective for certain classes of problems like bubble acoustics and combustion noise. A different approach for solving acoustic problems is to compute with individual particles following particle motion. In this paper, a Lagrangian approach to model sound propagation in moving fluid is presented and implemented numerically, using three meshfree methods to solve the Lagrangian acoustic perturbation equations (LAPE) in the time domain. The LAPE split the fluid dynamic equations into a set of hydrodynamic equations for the motion of fluid particles and perturbation equations for the acoustic quantities corresponding to each fluid particle. Then, three meshfree methods, the smoothed particle hydrodynamics (SPH) method, the corrective smoothed particle (CSP) method, and the generalized finite difference (GFD) method, are introduced to solve the LAPE and the linearized LAPE (LLAPE). The SPH and CSP methods are widely used meshfree methods, while the GFD method based on the Taylor series expansion can be easily extended to higher orders. Applications to modeling sound propagation in steady or unsteady fluids in motion are outlined, treating a number of different cases in one and two space dimensions. A comparison of the LAPE and the LLAPE using the three meshfree methods is also presented. The Lagrangian approach shows good agreement with exact solutions. The comparison indicates that the CSP and GFD method exhibit convergence in cases with different background flow. The GFD method is more accurate, while the CSP method can handle higher Courant numbers.

Hydrophilic coatings have recently emerged as a new approach to avoid the adhesion of (bio)organisms on surfaces immersed in water. In these coatings the hydrophilic character is crucial for the anti-fouling (AF) performance. However, this property can be rapidly lost due to the inevitable damages which occur at the surface, reducing the long-term effectiveness of the AF functionality. We report hydrophilic polycarbonate-mPEG polyurethane coatings with tunable hydrophilic properties as well as an excellent and long-term stability in water. The coatings exhibit low protein adhesion values and are able to self-replenish their hydrophilicity after damage, due to the existence of a reservoir of hydrophilic dangling chains incorporated in the bulk. The combination of low T_g and sufficient mobility of the mPEG dangling chains (enabled by chains with higher molecular weight) proved to be crucial to ensure autonomous surface hydrophilicity recovery when the coatings were immersed in water. This coatings and design approach offer new possibilities towards high performance AF coatings with an extended service life-time which can be used in several major applications areas, such as marine and biomedical coatings, with major economic and environmental benefits.

In higher education, the cultivation of research competency is pivotal for students’ critical thinking development and their subsequent transition into the professional workforce. While statistics plays a fundamental role in supporting the completion of a research project, it is often perceived as challenging, particularly by students in majors outside mathematics or statistics. The connection between students’ statistical proficiency and their research competency remains unexplored despite its significance. To address this gap, we utilized the supervised machine learning approach to predict students’ research competency, as represented by their performance in a research methods class, with predictors of students’ proficiency in statistical topics. Predictors relating to students’ learning behavior in a statistics course such as assignment completion and academic dishonesty are also included as auxiliary variables. Results indicate that the three primary categories of statistical skills—namely, understanding of statistical concepts, proficiency in selecting appropriate statistical methods, and statistics interpretation skills— can be used to predict students’ research competency, as demonstrated by their final course scores and letter grades. This study advocates for strategic emphasis on the identified influential topics to enhance efficiency in developing students’ research competency. Findings could inform instructors in adopting a strategic approach to teaching the statistical component of research for enhanced efficiency.

Open-vocabulary learning has recently gained prominence as a means to enable image segmentation for arbitrary categories based on textual descriptions. This advancement has extended the applicability of segmentation systems to a broader range of generally purpose scenarios. However, current methods often revolve around specialized architectures and parameters tailored to specific segmentation tasks, resulting in a fragmented landscape of segmentation models. In response to these challenges, we introduce OVAMTSeg, a versatile framework designed for Open-Vocabulary and Multitask Image Segmentation. OVAMTSeg harnesses adaptive prompt learning to empower the model to capture category-sensitive concepts, enhancing its robustness across diverse multi-task and scenario contexts. Text prompts are employed to effectively capture semantic and contextual features of the text, while cross-attention and cross-modal interactions enable the fusion of image and text features. Furthermore, a transformer-based decoder is incorporated for dense prediction. Extensive experimental results underscore the effectiveness of OVAMTSeg, showcasing its state-of-the-art performance and superior generalization capabilities across three segmentation tasks. Notable achievements include a 47.5 mIoU in referring expression segmentation, 51.6 mIoU on Pascal-VOC with four unseen classes, 46.6 mIoU on Pascal-Context in zero-shot segmentation, 65.9 mIoU on Pascal-5i, and 35.7 mIoU on COCO-20i datasets for one-shot segmentation.

This paper presents a piezoresistive pressure sensor with a shield layer for improved stability. Compared with the conventional piezoresistive pressure sensors, p-type piezoresistors are covered by an n-type shield layer, which is formed by ion implantation. The proposed pressure sensors have been successfully fabricated by bulk micromachining techniques. The impact of electrical field on piezoresistors is studied by simulation. The temperature drift of the pressure sensor has been investigated by both simulation and experimental measurement. Characteristics of developed pressure sensors are tested from -40 C to 125 C. A sensitivity of 0.022 mV/V/KPa and a maximum non-linearity of 0.085% FS are measured for the fabricated sensor in a pressure range of 1 MPa. The temperature coefficients of resistance of shielded piezoresistors are found to be smaller than those of un-shielded ones. It is demonstrated that the shield layer is able to reduce the drift caused by electrical field and ambient temperature variation.

Background: Schizophrenia and treatment-resistant schizophrenia (TRS) are associated with aberrations in immune-inflammatory pathways. Increased High Mobility Group Protein 1 (HMGB1), an inflammatory mediator, and Dickkopf-Related Protein (DKK1), a Wnt/β-catenin signaling antagonist, affect the blood-brain-barrier and induce neurotoxic effects and neurocognitive deficits.Aim of the study: The present study aims to examine HMGB1 and DDK1 in non-responders to treatments with antipsychotics (NRTT, n=60), partial RTT (PRTT, n=55) and healthy controls (n=43) in relation to established markers of schizophrenia including IL-6, IL-10 and CLL11 (eotaxin); and to delineate whether these proteins are associated with the schizophrenia symptom subdomains and neurocognitive impairments.Results: HMGB1, DKK1, IL-6 and CCL11 were significantly higher in schizophrenia patients than in controls. DKK1 and IL-6 were significantly higher in NRTT than in PRTT and controls while IL-10 was higher in NRTT than in controls. Binary logistic regression analysis showed that schizophrenia was best predicted by increased DDK1 and HMGB1 while NRTT (versus PRTT) was best predicted by increased IL-6 and CCL11 levels. A large part of the variance in psychosis, hostility, excitation, mannerism and negative (PHEMN) symptoms, and formal thought disorders was explained by HMGB1, IL-6, and CCL11 while most neurocognitive functions were predicted by HMGB1, DDK1 and CCL11. Conclusion: The neurotoxic effects of HMGB1, DKK1, IL-6 and CCL11 including effects on the blood-brain-barrier and the Wnt/β-catenin signaling pathway may cause impairments in executive functions, and working, episodic and semantic memory and explain, in part, PHEMN symptoms and a non-response to treatment with antipsychotic drugs.

The Transformer architecture, while adept at capturing context through self-attention, falls short in encapsulating complex syntactic structures effectively. Addressing this gap, we introduce the Linguistic Structure through Graphical Interpretation with BERT (LSGIB) approach in Machine Translation (MT) frameworks. Combining the strengths of Graph Attention Network (GAT) and BERT, LSGIB intricately captures syntactic dependencies as explicit knowledge from the source language. This enhances the source language representation and aids in more accurate target language generation. Our empirical analysis leverages gold-standard syntax-annotated sentences and employs a Quality Estimation (QE) model. This approach enables us to assess translation improvements in terms of syntactic accuracy, extending beyond traditional BLEU score metrics. The LSGIB model demonstrates superior translation quality across diverse MT tasks, maintaining robust BLEU scores. Our study delves into the optimal sentence lengths benefiting from LSGIB and identifies which syntactic dependencies are more precisely captured. We observe that GAT's ability to learn specific dependency relations directly influences the translation quality of sentences with those relations. Additionally, we discover that incorporating syntactic structure into BERT's intermediate and lower layers offers a novel approach to modeling linguistic structure in source sentences.

The Norwegian Museum of Science and Technology have developed a learning concept for school classes in science centres named ‘learning trails’. In this concept, groups of students perform a series of thematically related experiments with installations in the science centre. The learning trails are designed to support the generic learning outcomes for science centre visits. We argue for using the previously developed Engagement Profile in an indicator to determine both media forms and generic learning outcomes for such learning concepts. Further, we implemented the learning trails in two modes: one mode used paper-based content to guide the students, while the other mode supported the use of tablet PCs where engaging content is triggered when the students approach the location of an experiment in the learning trail. We studied the engagement factors of the learning trails and observed how school classes use these. In a study with 113 students from lower secondary school, they answered short questionnaires that were integrated into the implementation of the learning trails. While the concept of the learning trails was evaluated positively, we could not find significant differences in how engaging the two implemented modes were.

Glioblastoma (GBM) is the most common malignant brain tumor in adults. Despite advancements in treatment, the prognosis for patients with GBM remains poor due to its aggressive nature and resistance to therapy. CRISPR-based genetic screening has emerged as a powerful tool for identifying genes crucial for tumor progression and treatment resistance, offering promising targets for tumor therapy. In this review, we provide an overview of the recent advancements in CRISPR-based genetic screening approaches and their applications in GBM. We highlight how these approaches have been used to uncover genetic determinants of GBM progression and susceptibility to various therapies. Furthermore, we discuss ongoing challenges and future directions of CRISPR-based screening methods in advancing GBM research.

In Bangladesh, microcredit program has been in function for almost half a century. Though popularly termed as a tool for poverty alleviation and women empowerment, criticism about microcredit program’s actual effectiveness isn’t new. This study attempts to evaluate the impact of such programs by measuring borrowers’ social mobility. Using a multidimensional approach, indicators like household income, economic susceptibility, living conditions, consumption pattern, children’s education, healthcare facilities, women’s participation in decision-making were taken into account for measurement. Quantitative method was used. Based on a non-probability sampling, 107 microcredit borrowers were selected for conducting interview schedules who live in a rural, a semi-urban and an urban area. Statistical analysis of data reveals that those who have been taking loans for several number of years have all managed to increase their income level to a variety of extent, but only those have gained some sort of mobility who have been taking loans for more than 4-5 years and have taken 5 times or more. Few of them have actually moved from microcredit to become a microfinance client by taking bigger amount of loans and having savings. Positive responses about the indicators being used in the study were found among the handful of those who have mobilized significantly. In true sense, most of the borrowers are stuck at the bottom end of socio-economic ladder and are struggling to manage a better living standard.

It is unavoidable that the characteristics of the robot system alter inexactly or cannot be correctly determined during movement and are impacted by external disturbances. There are many adaptive control methods, such as sliding control or neural control, to improve the quality of trajectory tracking for robot motion systems. Still, those methods require a large amount of computation related to solving the problem of constrained nonlinear optimization problem. The article presents some techniques for determining an intelligent controller's online learning function parameters, including two circuits: the inner circuit is a state feedback linearized controller, and the outer course is an Interactive learning controller and does not use the robot's mathematical mode with function parameters online optimal learning and intelligent online learning closely following the joint model to stabilize the robot system. Finally, the 2-DOF planar robot simulation is performed on Matlab software R2022b. The findings indicate that outstanding tracking performance is achievable.

Abstract: Congenital hyperinsulinism (CHI) is a rare disorder of glucose metabolism and is the most common cause of severe and persistent hypoglycemia (hyperinsulinemic hypoglycemia, HH) in the neonatal period and childhood. Most cases are caused by mutations in the ABCC8 and KCNJ11 genes that encode the ATP-sensitive potassium channel (KATP). We present the correlation between genetic heterogeneity and the variable phenotype in patients with early-onset hyperinsulinemic hypoglycemia caused by ABCC8 gene mutations. In the first patients, which presented persistent severe hypoglycemia since the first day of life, molecular genetic testing revealed the presence of a homozygous mutation in the ABCC8 gene [deletion in the ABCC8 gene c.(2390+1_2391-1)_(3329+1_3330- 1)del] correlated with a diffuse form of hyperinsulinism (the parents being healthy heterozygous carriers). In the second patient, the onset was on the third day of life with severe hypoglycemia, and genetic testing identified a heterozygous mutation in the ABCC8 gene c.1792C&gt;T (p.Arg598*) inherited on the paternal line, which led to the diagnosis of focal form of hyperinsulinism. To locate the focal lesions, (18)F-DOPA (3,4-dihydroxy-6-[18F]fluoro-L-phenylalanine) PET/CT was recommended (an investigation that cannot be carried out in the country), but the parents refused to carry out the investigation abroad. In this case, early surgical treatment could have been curative. In addition, the second child also presented secondary adrenal insufficiency requiring replacement therapy. At the same time, she developed early recurrent seizures that required antiepileptic treatment. We emphasize the importance and of molecular genetic testing for diagnosis, management and genetic counseling in patients with HH.

The present study comprises the second part of our previous work that dealt mainly with the phytochemical and physicochemical characterization of green coffee, clove, cinnamon/clove and nutmeg ethanolic extracts of grape origin. In the present study, we focused on producing a discriminating model concerning green coffee, clove, cinnamon, cinnamon and clove, and nutmeg fine powders based on multivariate analysis of variance and supervised learning on data of volatile compounds analysis, carried out with solid phase dynamic extraction in combination with gas chromatography/mass spectrometry. Results showed that 7 volatile compounds namely ethylene, methanol, 3-methylpentane, ethyl acetate, 9-hexadecen-1-ol, toluene, and methyl acetate could differentiate the investigated samples resulting in a 100% classification rate using the cross-validation method of linear discriminant analysis. Results were further confirmed using partial least squares regression analysis. The study contributes to the typification of green coffee, cinnamon, clove, cinnamon and clove and nutmeg, based on selected volatile compounds, and provides further support to the literature by means of possible adulteration given the statistical models developed.