When a grid-forming (GFM) inverter is connected to a low or medium voltage weak power grid, the line impedance with resistive-inductive characteristics will cause power coupling. Typical GFM decoupling control strategies are designed under nominal line impedance parameters. However, there are deviations between the nominal line impedance and actual parameters, resulting in poor decoupling effects. Aiming at this problem, this paper proposes a power decoupling strategy based on a reduced-order extended state observer (ESO). Firstly, the power dynamic model of GFM is established based on the dynamic phasor method. Then, the model deviation and power coupling due to line impedance parameter perturbation are estimated as internal disturbances of the system, and the disturbances are compensated on the basis of typical power control strategy and virtual impedance decoupling. Good decoupling performance is obtained under different impedance parameters, improving the control strategy's robustness. Finally, the effectiveness of the proposed method is verified by the results of RT Box hardware-in-the-loop experiments.

Retired Electric vehicles (EVs) batteries are reused in second life energy storage applications. However, the overall performance of repurposed energy storage system (ESS) is limited by the unevenness of individual batteries use in it. Therefore, battery grading is required for optimal performance of ESS. Electrochemical impedance spectroscopy (EIS) based evaluation of battery aging is a promising way to grade lithium-ion batteries. However, it is not practical to measure impedance of mass retired batteries due to high complexity and slowness. In this paper, a broadband multi-sine binary signal (MSBS) perturbation integrated with multichannel EIS system is presented to measure impedance spectra for high-speed aging evaluation of lithium-ion batteries or modules. The measurement speed is multi-times higher than conventional EIS with single-channel configuration. The broadband MSBS is validated with reference sinusoidal sweep perturbation and corresponding root-mean-square error (RMSE) analysis is performed. Moreover, the accuracy of the presented multichannel EIS system is validated by impedance spectra measurement of Samsung INR18650-29E batteries and comparing it with those measured with commercial EIS instrument. A chi-squared error under 0.641% is obtained for all 8-channels. Since the non-linearity of battery has significant impact on quality of impedance spectra. Therefore, Kronig-Kramer (KK) transform validation is also performed.

This work presents a nonlinear model predictive control scheme that challenges overcoming the obstacles holding back over decades to develop affordable autonomous control and monitoring systems applied in the large-scale industry. Among the numerous proposals in the literature, most do not consider the significant fluctuation of kinetic parameters in the reduced mathematical model ADM2, widely used for control and monitoring purposes. The prevalent cause, on a basis, is the lack of information caused by some dynamics and parameters that cannot be measured in real-time by reliable sensors. In addition, to make matters worse, those systems inherently act with nonlinear nature and have a high sensitiveness to uncontrollable inputs and perturbations. Therefore, to prevent these drawbacks, this work proposes a new methodology that reconstructs the lack of information from the non-measurable dynamics, concentration of bacterias, and the kinetic parameters related to reaction rates. Simulations results demonstrate the effectiveness of the methodology compared with traditional industrial control schemes.

Diesel is consistently a very popular fuel for internal combustion engines. Its consumption in the European Union has been rising over recent years, as has the number of engines increasingly sensitive to fuel contamination. One of the most important parameters affecting diesel quality is water content. Although its exceedances of the standard’s permissible amount are not common, they carry the risk of serious damage to expensive, modern fuel injection systems. Current methods of measuring water content require both specialised personnel and equipment, as well as transporting the sample to a suitable laboratory. The research presented in this paper was aimed at verifying whether it would be possible to test the moisture content of diesel using impedance spectroscopy. Once refined, such measurement method could be used in situ. Analysing the properties of diesel is challenging, mainly because many types of the fuel are sold, the chemical composition of which is always a well-guarded manufacturer’s secret. The experimental results obtained on many types of commercially available diesel show that it is possible to use impedance spectroscopy to estimate the water content of different types of diesel fuel. The measurement accuracy achieved makes it possible to detect approaching or exceeding the permissible water content.

Building defects are very prevalent and contribute significantly to a building's economic value. There are numerous information sources on building defects that have a lot potential for learning more about building defects. This study aimed to identify the information sources used in previous building defect studies and to identify the motivation for carrying out such studies. To fulfil this aim a scoping study was carried out. The information sources identified included insurance companies, private databases, questionnaire surveys, lawsuits, building surveys, client complaint forms, and maintenance reports. This study found that insurance company and client complaint forms include the largest collection of real building defect cases, but such databases may lack detailed descriptions of the causes of the defects. The main purposes of building defects studies identified here included design challenges, identification of defects, building maintenance management, quality management, systematization in data collection, providing an overview of typical defects, and classifying defects. Identification was found to be the most common purpose, indicating that the industry wants to learn more. This study identified research gaps in the climate perspective in relation to building defects. Most of the studies focused on the economical perspective, and none focused on the carbon footprint perspective.

This work compared the performance of three methods for constructing a regional ensemble prediction system (EPS) for wind speed forecasts: dynamical downscaling, breeding of growth modes (BGM), and blending method. The Weather Research and Forecasting (WRF) model was used to downscale the European Centre for Medium-range Weather Forecast (ECMWF) EPS. In addition, as the BGM method needs observation data for generating scaling factors, an alternative method for generating scaling factors was proposed to eliminate dependence on observation data. One-month tests between October 1st and October 30th, 2020, were implemented to evaluate the performance of three methods in the Gansu province of China. The results demonstrate that the blending method outperforms the other two methods. Furthermore, the difference in performance is evident mainly in early forecast lead time and becomes negligible as forecast time increases.

Homotopy perturbation and analysis methods have been widely used to obtain both approximate and exact so- lutions to nonlinear problems. In general, these two methods are based on the Taylor series with respect to an embedding parameter. Many researchers have compared the two methods and raised more concerns on the homo- topy perturbation method (HPM) because the homotopy analysis method (HAM) contains a convergence-control parameter ~: For this reason, in this article, a more general form of HPM is introduced as the -homotopy per- turbation method (-HPM), which contains a control parameter : The introduction of parameter  in this new modi cation gives a better way to adjust and control the convergence region and the rate of the series solution. We con rm through the given examples in this study that the HPM is a special case of the -HPM. The error and convergence analysis of this proposed method are also presented

This paper presents a non-perturbative method for solving eigenproblems. This method applies to almost all potentials and provides non-perturbative approximations for any energy level. The method converts an eigenproblem into a perturbation problem, obtains perturbation solutions through standard perturbation theory, and then analytically continues the perturbative solution into a non-perturbative solution.

Aiming at the development of the application of massive and heterogeneous LEO constellations, the influence of typical perturbation forces on the orbit prediction of LEO satellites at different altitudes is analyzed. Firstly, the main perturbation force model of LEO satellites is introduced. Then experiments for analyzing the influence of orbit prediction on LEO satellites at different altitudes are designed. Finally, the influence of typical perturbation forces on the orbit prediction under different prediction durations by numerical analysis is assessed systematically, and the orbit prediction of LEO satellites with different non-spherical gravitational field orders, ocean tide orders and atmospheric density models were compared and calculated. The research results show that different orders of non-spherical gravitational fields should be considered when the altitude of satellites is different, the reasonable gravitational field orders for LEO satellites at 500km, 1000km, 1500km and 2000km under 1-hour forecast time are 140x140, 80x80, 60x60 and 40x40 orders, the reasonable orders of ocean tide perturbation for 1500km and 2000km satellites are 20x20 orders. Under the 24-hour forecast time, atmospheric resistance has a great influence on the precision of LEO satellites at orbit altitude below 1,000km. The forecast deviation of the LEO satellites orbit at 500km reaches 8751.576m. The difference of orbit precision between different atmospheric density models is in the meter level. The orbit deviation by the Standard Atmosphere 1976 and NRLMSISE 2000 atmospheric models respectively reaches 25.494m. Relevant conclusions provide support for the optimization and selection of dynamical models in high precision orbit determination and fast orbit prediction of LEO satellites.

Elizabethkingia anophelis is an opportunistic pathogen causing lifethreatening infections in humans, particularly in immunocompromised patients, neonates and elderly. Infections caused by this species are exceptionally challenging to treat due to its multiresistance to antimicrobials. We report a case of central line-associated bloodstream infection by E. anophelis in a 2.5-year-old girl with acute lymphoblastic leukemia successfully treated with a combination of piperacillin/tazobactam and amikacin. The literature was also reviewed on paediatric infections caused by E. anophelis. Accurate identification with MALDI-TOF, or using molecular techniques, is crucial because of varying susceptibilities among species. Early, accurate diagnosis and prompt effective treatment optimize outcomes.

Since general relativity (GR) has already established that matter can simultaneously have two different values of mass depending on its context, we argue that the missing mass attributed to non-baryonic dark matter (DM) actually obtains because there are two different values of mass for the baryonic matter involved. The globally obtained "dynamical mass'' of baryonic matter can be understood as a small perturbation to a background spacetime metric even though it's much larger than the locally obtained "proper mass". Having successfully fit the SCP Union2.1 SN Ia data without accelerating expansion or a cosmological constant, we employ the same ansatz to compute dynamical mass from proper mass and explain galactic rotation curves (THINGS data), the mass profiles of X-ray clusters (ROSAT and ASCA data) and the angular power spectrum of the cosmic microwave background (Planck 2015 data) without DM. We compare our fits to modified Newtonian dynamics (MOND), metric skew-tensor gravity (MSTG) and scalar-tensor-vector gravity (STVG) for each data set, respectively, since these modified gravity programs are known to generate good fits to these data. Overall, we find our fits to be comparable to those of MOND, MSTG and STVG. While this favorable comparison does not establish the validity of our proposition, it does provide confidence in using the fits to pursue an underlying action. Indeed, the functional form of our ansatz reveals an interesting structure in these fits.

The systematic sampling is used as a method to get the quantitative results from the tissues and the radiological images. Systematic sampling on real line (R) is a very attractive method within which the biomedical imaging is consulted by the practitioners. For the systematic sampling on R, the measurement function (MF) is occurred by slicing the three-dimensional object equidistant systematically. The currently used covariogram model in variance approximation proposed by [28,29] is tested for the different measurement functions in a class to see the performance on the variance estimation of systematically sampled R. This study is an extension of [17], and an exact calculation method is proposed to calculate the constant λ(q,N) of confidence interval in the systematic sampling. The exact value of constant λ(q,N) is examined for the different measurement functions as well. As a result, it is observed from the simulation that the proposed MF should be used to check the performances of the variance approximation and the constant λ(q,N). Synthetic data can support the results of real data.

The fitting and modeling of skewed, complex, symmetric, and asymmetric datasets is an exciting research topic in many fields of applied sciences, notably lifetime, medical, and financial sciences. The Heavy tailed Nadarajah Haghighi model is introduced by compounding the heavy tailed family and Nadarajah Haghighi distribution in this paper. The so obtained model has three parameters accounting for the scale and shape of the distribution. The proposed distribution's fundamental characteristics such as probability density, cumulative distribution, hazard rate, and survival functions are provided, and several key statistical properties are established, and several entropy information measures are proposed. The estimation of model parameter is performed via the ML procedure. Further, different simulation experiments are conducted to demonstrate the performance of proposed estimator’s using some measure, like the average estimate, the average bias, and associated mean square error. Finally, we are applied our proposed model to analyze three different real datasets. In our illustration, we are compared the practicality of the recommended model with several well-known competing models.

The capacitated team orienteering problem with time windows (CTOPTW) is a NP-hard combinatorial optimization problem. In the CTOPTW, a set of customers is given each with a profit, a demand, a service time and a time window. A homogeneous fleet of vehicles is available for serving customers and collecting their associated profits. Each vehicle is constrained by a maximum tour duration and a limited capacity. The CTOPTW is concerned with the determination of a preset number of vehicle tours that begin and end at a depot, visit each customer no more than once while satisfying the time duration, time window and vehicle capacity constraints on each tour. The objective is to maximize the total profit collected. In this study we propose an iterated local search (ILS) algorithm to deal with the CTOPTW. ILS is a single solution based meta-heuristic that successively invokes a local search procedure to explore the solution space. A perturbation operator is used to modify the current local optimum solution in order to provide a starting solution for the local search procedure. As different problems and instances have different characteristics, the success of the ILS is highly dependent on the local search procedure, the perturbation operator(s) and the perturbation strength. The basic ILS uses a single perturbation operator and the perturbation strength remains the same during the optimization process. To address these issues, we use three different perturbation operators and a varying perturbation strength which changes as the algorithm progresses. The idea is to assign a larger perturbation strength in the early stages of the search in order to focus on exploring the search space. The perturbation strength is gradually decreased so that we focus more on exploitation. The computational results show that the proposed ILS algorithm is able to generate high quality solutions on the CTOPTW benchmark instances taken from the scientific literature, demonstrating its efficiency in terms of both the solution quality and computational time. Moreover, the proposed ILS produces 21 best known results and 5 new best solutions.

High hepcidin is linked to low-grade inflammation and lower iron levels. The consequence of testosterone replacement therapy (TRT) on inflammation and risk of cardiovascular disease (CVD) is undetermined. We investigate the effect of TRT on the inflammatory cardiovascular risk markers hepcidin-iron, fibroblast growth factor 23 (FGF23)-phosphate-klotho, and calprotectin pathways. Methods: A randomized, placebo-controlled, double-blinded study at an academic tertiary-care medical center. Interventions were testosterone gel (TRT, n=20) or placebo gel (n=19) for 24 weeks. We included 39 men (50─70 years) with type 2 diabetes (T2D) on metformin monotherapy with bioavailable testosterone levels <7.3 nmol/L. Body composition was assessed by DXA- and MRI-scans; main study outcomes were serum hepcidin-iron, FGF23, phosphate, klotho, and calprotectin. Results: Hepcidin levels decreased during TRT (β=-9.5 ng/mL, P<0.001), lean body mass (β=1.9 kg, P=0.001) increased, and total fat mass (β=-1.3 kg, P=0.009) decreased compared to placebo. Delta hepcidin was not associated with changes in lean body mass or fat mass. Iron and the pathways of FGF23-phosphate-klotho and calprotectin were unchanged during TRT. Conclusions: During TRT, the reduction in hepcidin was not associated with circulating iron levels, lean body mass, or fat mass; these findings suggested a direct anti-inflammatory effect of TRT and no indirect effect mediated through these factors.

Context. During the COVID-19 pandemic, patient care was mainly organised around the hospital. Pre-hospital care has, to our knowledge, never been evaluated. Objective: To evaluate the impact of pre-hospital pathways on hospitalisation during the last part of the pandemic. Design. This was a monocentric retrospective analysis of prospectively collected medical records. Data from patients admitted to our institute between 1 February and 7 March 2022 were analysed. Main Outcome Measure(s): The primary outcomes were defined as the number of hospitalisations, resuscitations, and deaths at the time of interview and in the subsequent 30 days. The main explanatory variables were times from onset of symptoms to care, age, gender, News2 score, comorbidities, and pre-hospital pathways and their duration. Results: Three pre-hospital pathways have been identified: a pathway in which the patient consults a general practitioner for a test (PHP1); a pathway in which the patient consulted for care (PHP2); and no pre-hospital pathway and direct admission to hospital (PHP3). Factors independently associated with outcome (hospitalisation) were being male (OR 95% CI; 2.21 [1.01–4.84], p=0,04), News2 score (OR 95% CI; 2.04 [1.65–2.51], p<0.001), obesity (OR 95% CI; 3.45 [1.48–8.09], p=0.005), D-dimers > 0.5 µg/ml (OR 95% CI; 3.45 [1.47–8.12], p=0.005), prolonged time from symptoms to hospital care (PHP duration) (OR 95% CI; 1.07 [1.01–1.14], p=0.03). All things being equal, patients with a “PHP2” pre-hospital pathway had a higher probability of hospitalisation compared to those with a “PHP3” pre-hospital pathway (OR 95% CI; 4.31 [1.48–12.55], p=0.007). Conclusions. Along with recognised risk factors such as gender, News 2 score, and obesity, the patient’s pre-hospital pathway is an important risk factor associated with hospitalisation.

The research on the excavation mechanical properties of underpass tunnels has already had certain results, but fewer of them consider the effects of dynamic and static loads on the excavation mechanical properties of underground tunnels at the same time, especially the lack of research cases of double-line highway tunnels with angled underpasses of existing railway tunnels. In this paper, based on the tunnel project of the new double-line Shiqian Highway Tunnel passing under the Hurong Railway at an oblique angle, the mechanical parameters of the rock body in the cross-tunneling area under the influence of static and dynamic load coupling are obtained by using the disturbance quantification coefficients and the Hoek-Brown criterion based on the method of over-advanced geological prediction and the investigation of the surrounding rock on the palisade face, and the engineering-scale finite element model is constructed and the mechanical characteristics of the excavation in the tunnel of the double-lane highway tunnel passing under the existing railroad under the influence of the static and dynamic loads are analyzed. The results show that: the new tunnel rock movement law for the top of the arch sinking, bottom plate bulging, side wall to move outward, the height and width of the arch and bottom plate arch with the tunnel excavation and increase, the side wall rock displacement effect is smaller; left and right lines of the tunnel disturbed area of the rule of change is similar; the existing tunnel bottom plate displacement is more than the top plate and the left and right side walls by the excavation of the time step influence is larger. Typical profile displacement is mainly determined by the distance from the excavation surface; the new tunnel in the four types of calculation conditions of the rock disturbance angle is the same; the existing tunnel roof and side wall Von Mises stress extreme occurs in the tunnel structure, the bottom plate there are pressure relief and pressure-bearing areas; based on the displacement control criteria, the recommended upper and lower step blasting method.

For multi-sensor integrated systems, such as a mobile mapping system (MMS), data fusion at sensor-level, i.e., the 2D-3D registration between optical camera and LiDAR, is a prerequisite for higher level fusion and further applications. This paper proposes a line-based registration method for panoramic images and LiDAR point cloud collected by a MMS. We first introduce the system configuration and specification, including the coordinate systems of the MMS, the 3D LiDAR scanners, and the two panoramic camera models. We then establish the line-based transformation model for panoramic camera. Finally, the proposed registration method is evaluated for two types of camera models by visual inspection and quantitative comparison. The results demonstrate that the line-based registration method can significantly improve the alignment of the panoramic image and LiDAR datasets under either the ideal spherical or the rigorous panoramic camera model, though the latter is more reliable.

This work presents a methodology that seeks to be a new standard in modeling identification in anaerobic digestion reactors. Because it is not possible to measure all variables with reliable and cost-efficient real-time methods, a specific structure composed of an asymptotic observer for the concentration of state variables; acidogenic and methanogenic bacterias, unlock the use of new types of raw sludges for industrial control and monitoring purposes. New yield parameters were included in the reduced anaerobic digestion model (ADM2) used as the core, precisely two terms in total alkalinity, to bring about the modeling of additional organic materials at inlet containing proteins or amino acids. The fermentation of these substances introduces ammonium, providing variations in the amount of alkalinity available inside the reaction. The new model is used to solve an optimization problem that calculates the parameters that best fit the dynamics of state variables with the same information taken on the experimental data. The adjustment process started with the genetic algorithm; however, to improve the performance, a novel method is proposed called step-ahead. Together, including the design of an asymptotic observer, numerical simulations demonstrate the strengths of the structure, which constitutes a significant step in paving the way further to implement feasible, cost-effective control and monitoring systems in the industry.

The Flack Parameter is now almost universally reported for all chiral materials characterized by X-ray crystallography. It’s elegantly simplicity was an inspired development by Flack, and although the original algorithm for its computation has been strengthened by other workers, it remains an essential outcome for any crystallographic structure determination. As with any one-parameter metric, it needs to be interpreted in the context of its standard uncertainty.

Accurate forecasting of icing thickness has a great significance for ensuring the security and stability of power grid. In order to improve the forecasting accuracy, this paper proposes an icing forecasting system based on fireworks algorithm and weighted least square support vector machine (W-LSSVM). The method of fireworks algorithm is employed to select the proper input features with the purpose of eliminating the redundant influence. In addition, the aim of W-LSSVM model is to train and test the historical data-set with the selected features. The capability of this proposed icing forecasting model and framework is tested through the simulation experiments using real-world icing data from monitoring center of key laboratory of anti-ice disaster, Hunan, South China. The results show that the proposed W-LSSVM-FA method has a higher prediction accuracy and it may be a promising alternative for icing thickness forecasting.

Sarcopenia becomes more common with age, being most prevalent among elderly individuals. According to the EWGSOP, muscle mass is one of the criteria for the evaluation of sarcopenia. The main methods for evaluating muscle mass are CT, MRI, and DXA, but these methods are difficult to apply in the field due to equipment costs, radioactivity, and lack of portability. BIVA and PhA are alternative approaches for assessing somatic cell mass and volume and do not require predictive equations. These variables are clinically relevant parameters that indicate cell health, especially cell membrane integrity and cell function. This study in sarcopenic and nonsarcopenic elderly volunteers aimed to determine the BIVA distribution pattern among individual sarcopenia patients; to evaluate the relationship between PhA and muscle strength, muscle quality, and physical function; and to find any correlates of PhA. The sample comprised 134 free-living elderly individuals of both sexes aged 69–91 years. Anthropometric parameters, grip strength, DXA findings, BIA results, and physical performance (the 6-meter walk test) were measured. Impedance vector distributions were evaluated in sarcopenia patients and healthy elderly individuals using BIVA. According to the AWGS criteria, sarcopenia was diagnosed according to DXA findings, grip strength and physical performance test results. Group differences were evaluated using the t test, Mann‒Whitney U test, and Hotelling's T2 test. Correlation analysis was performed to identify variables significantly associated with PhA. Linear regression analysis was performed to determine whether PhA was associated with muscle strength, muscle quality and physical function. BIVA detected a significant difference between the sarcopenia and non-sarcopenia groups (both sexes) due to higher R/H values and lower phase angles in a few individuals, whereas Xc/Ht values did not differ between the two groups. The sarcopenia group had a significantly lower PhA than the non-sarcopenia group among both males (p&lt;0.01) and females (p&lt;0.05). PhA was significantly correlated with age, ASM, HGS, and muscle quality in both sexes and significantly correlated with ASM/Ht2 and physical performance in males. PhA was a significant indicator of muscle strength in both males (β = 2.6; p&lt;0.01) and females (β = 3.4; p&lt;0.01), a significant indicator of muscle quality in both males (β = 0.07; p&lt;0.05) and females (β = 0.17; p&lt;0.01), and a significant indicator of physical performance in males (β = 0.3; p&lt;0.01). BIVA can detect changes in muscle mass in individuals with sarcopenia and is a practical method for the assessment of sarcopenia in the field. PhA is a good indicator of muscle strength, muscle quality and physical performance (in males). These methods can help diagnose sarcopenia in elderly individuals with reduced mobility.

We hypothesis that large earthquakes generate Horndeski-like Gravitational Wave (GW). We find that such a Horndeski-like GW propagates with the speed of sound. The sound waves generated by an earthquake make a local and temporal change to the Earth’s diagravitational medium; therefore, they modify the GW speed in a standard, Alternative-Theory-of-Gravity (ATG) sense. The quantum of the Horndeski-like GW is a massless scalar quasiparticle and cannot exist outside of the propagation region of the P-field. The Horndeski-like GW may be detectable by future GW detectors with a sensitivity of 10−15 Hz^−1/2 in the region of 0.1–1 Hz.

The Vacuum Energy Parameter (VEP) of standard cosmology denotes the fraction of the critical density attributed to the accelerated expansion of the Universe. Astrophysical evidence sets the numerical range of VEP at 0.692 +, - 0.012, yet the root cause of these values is currently unknown. Drawing from the stochastic interpretation of early-Universe cosmology, we develop here a derivation of the VEP based on classical diffusion theory and the Langevin equation. Predictions are shown to be in reasonable agreement with observations.

A thorough analysis and comparison of the fatty acid profiles of stipe and blade from Laminaria hyperborea, a kelp species found in the northern Atlantic, is presented. Lipids were extracted and fractionated into neutral lipids, free fatty acids and polar lipids, then derivatized to fatty acid methyl esters prior to GC-MS analysis. A total of 42 fatty acids were identified and quantified, including the n-3 fatty acids α-linolenic acid, stearidonic acid and eicosapentaenoic acid. An n-6/n-3 ratio of 0.8:1 was found in blade and 3.5:1 in stipe, respectively. The ratios vary between the lipid fractions within stipe and blade, with the lowest ratio in the polar lipid fraction of blade. The fatty acid amounts are higher in blade than in stipe, and the highest amounts of n-3 fatty acids are found within the neutral lipid fractions. The amounts of polyunsaturated fatty acids are 3.4 times higher in blade than stipe. This study highlights the compositional differences between the lipid fractions of stipe and blade from L. hyperborea. The amount of polyunsaturated fatty acids, compared to saturated- and monounsaturated fatty acids, as well as the n-6/n-3-ratio, is known to influence human health. In the pharmaceutical, food, and feed industries this can be of importance for production and sale of different health products. Additionally, lipids are today among the unused by products of alginate production, exploiting this material for commercial interest should give both economical and environmental benefits.

A hypothesis that the generally accepted value of the LiPON conductivity should be attributed to the absorption and displacement currents is substantiated. The reason is a small contribution of the drift current due to field screening by the electric double layer. The basis for this assumption is the measurement of the LiPON absorption capacitance, according to which its dielectric constant is about 106. An alternative equivalent circuit containing a non-ideal absorption element is proposed and its impedance is calculated. It is shown that the Bode diagrams of the alternative circuit well approximate the experimental curves. Parameters and the magnitude of electric field screening are calculated basing on proposed model of a double electric layer. Considering the screening effect, the drift conductivity of LiPON is obtained, which value is in good agreement with the data on lithium concentration and mobility.

Epilepsy is a chronic neurological disorder characterized by recurring seizures resulting from abnormal neuronal hyperexcitability. In the case of pharmacoresistant epilepsy requiring resection surgery, identifying the epileptogenic zone (EZ) is crucial. Fast ripples (FRs; 200-600 Hz) are one of the promising biomarkers that can aid in EZ delineation. However, recording FRs requires small surface electrodes. These microelectrodes suffer from high impedance, which significantly impacts FR observability and detection. In this study, we explored the potential of a conductive polymer coating to enhance FR observability. We employed biophysical modeling to compare two types of microelectrodes: Gold (Au) and Au coated with the conductive polymer poly(3,4-ethylenedioxythiophene)-poly(styrene sulfonate) (Au/PEDOT:PSS). These electrodes were then implanted in the CA1 hippocampal neural network of epileptic mice to record FRs during epileptogenesis. Results showed that polymer-coated electrodes demonstrate two-order lower impedance and a higher transfer function amplitude and cut-off frequency. Consequently, FRs recorded with the PEDOT:PSS coated microelectrode yielded significantly higher signal energy compared to the uncoated one. The coating with PEDOT:PSS improved the observability of recorded FRs and therefore their detection. This work paves the way for the development of signal-specific microelectrodes design allowing better targeting of pathological biomarkers.

Various formulations of the exact renormalization group can be compared in the perturbative domain, in which we have reliable expressions for regularization-independent (universal) quantities. We consider the renormalization of the $\lambda\phi^4$ theory in three dimensions and make a comparison between the sharp-cutoff regularization method and other more recent methods. The former gives considerably better results, while the other methods are far from optimal in the perturbative domain. In addition, these methods present theoretical problems that are already manifest in the renormalization of mass.

A new method for multi-shot reconstruction of high-energy photon distributions in the context of studying the interaction between a beam and a plasma in plasma wakefield acceleration (PWFA) experiments is presented. The study investigates the effects of beam perturbations on betatron radiation and analyzes how these perturbations can lead to hosing, a transverse instability that can degrade the quality of the beam. The potential of betatron radiation spectroscopy as a non-invasive diagnostic technique for PWFA experiments is also emphasized.

Physics of high-Tc superconducting cuprates is obscured by the effect of strong electronic correlations. One way to overcome the problem is to seek for an exact solution at least within the small cluster and expand it to the whole crystal. Such an approach is in the heart of the cluster perturbation theory (CPT). Here we develop CPT for the dynamic charge and spin susceptibilities (spin-CPT), within which the correlation effects are explicitly taken into account by the exact diagonalization. We apply spin-CPT to the effective two-band Hubbard model for the cuprates obtained from the three-band Emery model and calculate one- and two-particle correlation functions, namely, spectral function and spin and charge susceptibilities. Doping dependence of the spin susceptibility was studied within spin-CPT and CPT-RPA that is the CPT generalization of the random phase approximation (RPA). Both methods produce the low energy response at four incommensurate wave vectors in qualitative agreement to the results of the inelastic neutron scattering on overdoped cuprates.

Pollen tubes grow by spatially and temporally regulated expansion of new material secreted into the cell wall at the tip of the tube. A complex web of interactions among cellular components, ions and small molecule provides dynamic control of localized expansion and secretion. Cross-correlation studies on oscillating lily (Lilium formosanum Wallace) pollen tubes showed that an increase in intracellular calcium follows an increase in growth, whereas the increase in the alkaline band and in secretion both anticipate the increase in growth rate. Calcium, as a follower, is unlikely to be a stimulator of growth, whereas the alkaline band, as a leader, may be an activator. To gain further insight herein we reversibly inhibited growth with potassium cyanide (KCN), and followed the re-establishment of calcium, pH and secretion patterns as growth resumed. While KCN markedly slows growth and causes the associated gradients of calcium and pH to sharply decline, its removal allows growth and vital processes to fully recover. The calcium gradient reappears before growth restarts, however it is preceded by both the alkaline band and secretion, in which the alkaline band is slightly advanced over secretion. Thus the pH gradient, rather than the tip-focused calcium gradient, may regulate pollen tube growth.

More and more works are using machine learning techniques while adopting supervisory control and data acquisition (SCADA) system for wind turbine anomaly or failure detection. While parameter selection is important for modelling a wind turbine’s health condition, only a few papers have been published focusing on this issue and in those papers interconnections among sub-components in a wind turbine are used to address this problem. However, merely the interconnections for decision making sometimes is too general to provide a parameter list considering the differences of each SCADA dataset. In this paper, a method is proposed to provide more detailed suggestions on parameter selection based on mutual information. Moreover, after proving that Copula, a multivariate probability distribution for which the marginal probability distribution of each variable is uniform is capable of simplifying the estimation of mutual information, an empirical copula based mutual information estimation method (ECMI) is introduced for an application. After that, a real SCADA dataset is adopted to test the method, and the results show the effectiveness of the ECMI in providing parameter selection suggestions when physical knowledge is not accurate enough.

This paper proposes a definition of fractional line integral, generalising the concept of fractional definite integral. The proposal replicates the properties of the classic definite integral, namely the fundamental theorem of integral calculus. It is based on the concept of fractional anti-derivative used to generalise the Barrow formula. To define the fractional line integrals the Gr\"unwald-Letnikov and Liouville directional derivatives are introduced and their properties described. The integral is defined first for broken line paths and afterwards to any regular curve

The paper presents the possibility of using KINECT v2 module to control an industrial robot by means of gestures and voice commands. It describes elements of creating software for off-line and on-line robot control. The application for KINECT module was developed in C# language in Visual Studio environment, while the industrial robot control program was developed in RAPID language in RobotStudio environment. The development of a two-threaded application in RAPID language allowed to separate two independent tasks for the IRB120 robot. The main task of the robot is performed in thread no. 1 (responsible for movement). Simultaneously working thread no. 2 ensures continuous communication with the KINECT system and provides information about the gesture and voice commands in real time without any interference in thread no. 1. The applied solution allows the robot to work in industrial conditions without negative impact of communication task on the time of robot’s work cycles. Thanks to the development of a digital twin of the real robot station, tests of proper application functioning in off-line mode (without using a real robot) were conducted. Obtained results were verified online (on the real test station). Tests of correctness of gesture recognition were carried out, the robot recognized all programmed gestures. Another test carried out was the recognition and execution of voice commands. A difference in the time of task completion between the actual and virtual station was noticed - the average difference was 0.67 s. The last test carried out was to examine the impact of interference on the recognition of voice commands. With a 10dB difference between the command and noise, the recognition of voice commands was equal to 91.43%. The developed computer programs have a modular structure, which enables easy adaptation to process requirements.

In this study, cement is used as the component that provides the stabilizing effect in order to evaluate the hardness and stability of loess soil. To assess the strength characteristics of loess soil reinforced with cement, samples were created with four different cement contents and three different curing times. The materials were put through a series of tests to determine their flexural strength, direct shear strength, indirect tensile strength, and unconfined compressive strength. An appropriate cement dosage was found, in addition to a durability index that could be used to quantify the effect of water absorption investigations on cement-stabilized loess. Both of these discoveries were made simultaneously. Analyses of investigations such as scanning electron microscopy (SEM) and energy dispersive X-ray fluorescence spectrometry (XRF) examinations were carried out so that the fundamental mechanics of the materials could be comprehended. According to the findings, the cohesion of cement-stabilized loess is significantly more sensitive to structure than the friction angle of the material, and the cohesion is responsible for the increase in shear strength after remolding. To get the desired level of strength, it is necessary to adjust the cement's proportions. In addition, as the curing period progresses, we see an increase in the cement-stabilized loess's resistance and stiffness. This is because of the interactions that take place between the structure and the mineral composition. It is believed that this event was caused by the cementation that occurs naturally. As a consequence of this reaction, the production of new cementitious materials takes place. The cation exchange that causes the hydration and pozzolanic reaction that leads to the creation of aggregates and interparticle flocculation is responsible for their production. These findings suggest that cement may be utilized as a simple and effective method of loess stabilization, which will ultimately result in improved performance of the loess.

In this paper we introduce the New/Generalized two parameter Gamma function and Pochhammer symbol. We named them, as Generalized p - k Gamma Function and Generalized p - k Pochhammer symbol and denoted as $ _{p}^{a}\Gamma_{k}(x) $ and $ _{p}^{a}(x)_{n,k} $ respectively. We prove the several identities for $ _{p}^{a}\Gamma_{k}(x) $ and $ _{p}^{a}(x)_{n,k} $ those satisfied by the classical Gamma function. Also we provide the integral representation for the $ _{p}^{a}\Gamma_{k}(x) $

The paper presents a method for determining the mutual impedance of two dipoles located on a multilayer dielectric structure. Determining the mutual impedance of linear antennas is a complex issue and we are unable to obtain an exact solution, it is influenced by many elements (location, dimensions, electrical parameters of the earth, thickness of the substrate, thickness and antenna conductivity, etc.) In the case of antennas on a dielectric substrate, the coupling analysis is even more complicated, because the operation of these antennas is significantly influenced by the occurrence of surface waves conducted through an open dielectric structure. The problem was solved by the method of moments using the Galerkin method as its special case. The work uses a method developed by Richmond for obtaining the elements of the impedance matrix, based on the concept of reaction between sections of the base and testing functions. Their mutual interaction was described by the reaction of the electric field caused by the current flowing through one dipole with the current flowing through the other dipole. Based on this analysis, the mutual impedance of two arbitrarily oriented dipoles located on a multilayer dielectric was determined, where the current distribution and antenna lengths are arbitrary. A computer program was developed that allowed to determine the mutual impedance for freely oriented dipoles.

A rigorous perturbation analysis of the singular value decomposition of a real matrix of full column rank is presented. It is shown that the SVD perturbation problem is well posed only in case of distinct singular values. The analysis involves the solution of coupled systems of linear equations and produces asymptotic (local) componentwise perturbation bounds of the entries of the orthogonal matrices participating in the decomposition of the given matrix and of its singular values. Local bounds are derived for the sensitivity of the singular subspaces measured by the angles between the unperturbed and perturbed subspaces. An iterative scheme is described to find global bounds on the respective perturbations. The analysis implements the same methodology used previously to determine componentwise perturbation bounds of the Schur form and the QR decomposition of a matrix.

Balance requires constant adjustments in muscle activation to attain force steadiness. Creating appropriate training can be challenging. The purpose of this study was to examine the effects of two weeks front squat instability training using a water-filled training tube on force steadiness during an instability challenge. Control (CON, n= 13) and experimental (EXP, n=17) subjects completed pre and post testing for EMG variability by completing one set of 10 repetitions with a stable and unstable training tube. Electrodes were placed bilaterally on the anterior deltoid, paraspinal and vastus lateralis muscles. CON subjects completed 2 weeks of training using a stable training tube, while EXP subjects trained with a water-filled instability tube. EMG data were integrated for each contraction and force steadiness computed using the natural log of coefficient of variation. CON results showed no changes in force steadiness for any condition. EXP showed significant reductions in EMG activation variability across all muscles. These results indicate a significant training effect in reducing muscle activation variability in subjects training with a water-filled instability training device. Improvements seen in these healthy subjects supports development of training implements for a more clinical population to help improve force steadiness.

In this work, we studied the Green’s functions of the second order differential operators with involution. Uniform equiconvergence of spectral expansions related to the second-order differential operators with involution is obtained. Basicity of eigenfunctions of the second-order differential operator operator with complex-valued coefficient is established.

Metal-catalyzed lipid oxidation is a major factor in food waste, as it reduces shelf life. Addressing this issue, our study investigates the potential of hydrolysates derived from potato protein, a by-product of potato starch production, as metal chelating antioxidants. Through sequential enzymatic hydrolysis using Alcalase or Trypsin combined with Flavourzyme, we produced various hydrolysates, which were then fractionated via ultrafiltration. Using a combination of peptidomics and bioinformatics, we predicted the presence of metal-chelating and free radical scavenging peptides across all hydrolysate fractions, with a trend indicating a higher content of antioxidant peptides in lower molecular weight fractions. To validate these predictions, we utilized Surface Plasmon Resonance (SPR) and a 9-day emulsion storage experiment. While SPR demonstrated potential in identifying antioxidant activity, it faced challenges in differentiating between hydrolysate fractions due to significant standard errors. In the storage experiment, all hydrolysates showed lipid oxidation inhibition, though not as effectively as EDTA. Remarkably, one fraction (AF13) was not significantly different (p < 0.05) from EDTA in suppressing hexanal formation. These results highlight SPR and peptidomics/bioinformatics as promising yet limited methods for antioxidant screening. Importantly, this study reveals the potential of potato protein hydrolysates as antioxidants in food products, warranting further research.

(1) Background: In this work, a series of benzimidazole derivatives containing colchicine-like and cathechol-like moieties with methyl group substitution in the benzimidazole ring were evaluated for their in vitro antiproliferative, pro-apoptotic and antioxidative activity against highly invasive breast cancer cell line MDA-MB-231 and related impairment of tubulin dynamics; (2) Methods: MTT assay was used to evaluate the antiproliferative activity. In vitro tubulin polymerization assay as well as docking analysis was applied to prove the alterations in tubulin polymerization. Immunofluorescent and DAPI staining reveal the pro-apoptotic potential of benzimidazole derivatives and the effect on tubulin’s dynamics in living cells. The antioxidant activity was evaluated by scavenging of H2O2 and hypochlorite ion and ortho-phenanthroline tests; (3) Results: The compounds containing colchicine-like moiety displayed significant growth inhibitory effect against cancer cell line as was highlighted the role of methyl functional group on the tubulin aggregation and blockage of mitosis. All compounds showed an ability to scavenge H2O2, while the compounds with cathecol-like moiety were more effective against hypochlorite ion and chelation of iron; (4) Conclusions: The benzimidazole derivative containing colchicine-like moiety and methyl group substitution in benzimidazole ring is a potential antiproliferative and microtubule destabilizing agent.

This study aimed to assess the physical characteristics of elite international soccer referees, compare them with other referee populations in the literature, and establish reference tolerance ellipses for the bioelectrical impedance vector analysis (BIVA) point graph. Forty-one elite international soccer referees (age 38.8 ± 3.6 years) participated in the study. the participants underwent body composition assessments, including dual-energy X-ray absorptiometry, BIVA, and somatotype. The Somatotype Attitudinal Distance (SAD), the two-sample Hotelling’s T2 test, and the Mahalanobis test were used to determine somatotype and bioelectrical vector differences with the literature. The average somatotype of the referees was a balanced mesomorph (2.8, 6.5, 2.8). Elite international referees significantly differed from other samples in the literature (SAD = 2.1, 2.6, 2.9 with respect to Zimbabwean, Brazilian, and South African referees, respectively). The bioelectrical vector was significantly different from the general population (T2  76.6; F = 38.8; D = 1.44; P < 0.001) and athletes (T2  25.3; F = 12.6; D = 0.8; P < 0.001). Somatotype values and tolerance ellipses from this study may be useful as a reference for developing training programs and improving the selection process of referees in soccer.

Nonlinear nonparametric statistics (NNS) algorithm offers new tools for curve fitting. A relationship between k-means clustering and NNS regression points is explored with graphics showing a perfect fit in the limit. The goal of this paper is to demonstrate NNS as a form of unsupervised learning, and supply a proof of its limit condition. The procedural similarity NNS shares with vector quantization is also documented, along with identical outputs for NNS and a k nearest neighbours classification algorithm under a specific NNS setting. Fisher's iris data and artificial data are used. Even though a perfect fit should obviously be reserved for instances of high signal to noise ratios, NNS permits greater flexibility by offering a large spectrum of possible fits from linear to perfect.

Guessing effects frequently occur in testing data in educational or psychological applications. Different item response models have been proposed to handle guessing effects in dichotomous test items. However, it has been pointed out in the literature that the oftenemployed three-parameter logistic model poses implausible assumptions regarding the guessing process. The four-parameter guessing model has been proposed as an alternative to circumvent these conceptual issues. In this article, the four-parameter guessing model is compared with alternative item response models for handling guessing effects through a simulation study and an empirical example. It turned out that model selection for item response models should be rather based on the AIC than the BIC. However, the RMSD item fit statistic used with typical cutoff values was found to be ineffective in detecting misspecified item response models. Furthermore, sufficiently large sample sizes are required for sufficiently precise item parameter estimation. Moreover, it is argued that the criterion of statistical model fit should not be the sole criterion of model choice. The item response model used in operational practice should be valid with respect to the meaning of the ability variable and the underlying model assumptions. In this sense, the four-parameter guessing model could be the model of choice in educational large-scale assessment studies.

Vascular endothelial growth factor (VEGF) is a important biomarker with significant clinical importance. It plays a key role in angiogenesis, would healing, tumor growth, lung development, and in retinal diseases. Hence, detecting and quantifying VEGF is crucial in clinical diagnosis and prognosis of various diseases. In this work, a simple but highly cost-effective platform is developed for VEGF protein detection by using commercially available interdigitated sensors that are modified through surface chemistry tagged with DNA aptamer grafting. The dielectric characteristics between the fingers of sensor is modulated by the negatively charged aptamer-VEGF capture and the impedance is estimated using impedance analyzer. Impedance spectra tests was compared between pristine unmodified, functionalized monolayer surfaces and aptamer-grafted surfaces in order to evaluate the efficacy of VEGF detection. In our results, the sensitivity experiments as conducted had shown the ability of the interdigitated sensor to detect VEGF at a low concentration of 5 pM. The specificity of the functionalized sensor in detecting VEGF is further studied by comparing the impedance to platelet-derived growth factor (PDGF), and the results confirm the specificity of the sensor. Finally, an alternative illustration of impedance spectra is also proposed to improve the data visualization, and such presentation may be potential for intelligent VEGF detection.

Rail impedance directly affects the transmission performance of track circuit . Considering the condition of earth stratification, for the difficult to calculate the rail impedance due to the semi-infinite integration interval and the oscillation of the integrand by using the Carson formula, The truncation method is proposed to divide the impedance formula is divided into definite integral and tail integral. The integral is approximated by the spline function, and the tail integral is calculated by using the exponential integral and Euler formula. Based on it, the rail impedance calculation formula of track circuit is obtained. The electromagnetic field model of track circuit with earth stratification is simulated by finite element method, and the correctness of the method is verified. Based on the formula, the influence of current frequency, soil depth and conductivity on rail impedance is studied. The relative error between the calculated results of rail impedance and the simulation results of finite element is within 5%. It can be seen that the formula has high accuracy and correctly reflects the law of rail impedance variation with current frequency, soil depth and resistivity. It provides a reliable reference for the theoretical calculation of rail impedance of track circuit.

Pathogens and adulterants in human feeding consumables can be readily identified according to their electrical properties. Electrical bioimpedance analysis (BIA) has been widely used for body contents characterization, such as blood, urine, lactate and sweat. If the blood glucose concentration alters the electrical properties of the blood medium, then the impedance spectrum obtained by BIA can be used to measure glycemia. In some applications, artificial neural networks allows the correlation of these parameters (impedance and glucose concentration) by means of symbolic and statistical rules. According to our literature review, there is any physical model that allows the interpretation of the relationship between blood’s electrical properties, obtained by BIA, and the concentration of glucose in the blood plasma. This article proposes a simplified physical model for blood electrical conductivity as a function of glucose concentration, based on Bruggeman’s effective medium theory. The equations of this model were obtained considering an insulating phase distribution diffused in a conductive matrix, in which red blood cells are represented by macroscopic insulating nuclei and glucose molecules by microscopic insulating particles. The impedance spectrum for different glucose concentrations (4.0 to 6.8 mmol/L) in a blood sample, published by Kamat Bagul (2014), were compared with the proposed model. The results showed a significant correlation with the experimental data, showing a maximum error of 5.2%. The proposed model might be useful in the design of noninvasive blood glucose monitoring systems.

Bio-devices are designed to allow biological matter to perform in vitro almost the same functions it performs in vivo. Therefore, they can benefit from the specificities of such materials and are expected to perform better than traditional devices. On the other hand, the integration of biological material with electronic/electrochemical instrumentation requires careful attention and can produce unconventional results. In this paper, we describe the impedance response of an electrochemical cell that converts sunlight into electrical power. It uses the photosynthetic system known as Reaction Center, which is the core of photosynthesis in several living beings. Under illumination, an abrupt transformation drives the cell electrical response from insulator to conductor and a photocurrent is observed. The impedance spectrum shows a peculiar shape which significantly modifies with the protein activation. It has been analyzed by means of a graphical/analytical/ numerical procedure. The modelling identifies an analogue electrical circuit, whose parameters give quantitative information about the underlying process. Finally, an appropriate normalization of data is proposed which validates data in dark and light and can be useful as a fast screening of measurements.

This paper is concerned with variational methods for open quantum systems with Markovian dynamics governed by Hudson-Parthasarathy quantum stochastic differential equations. These QSDEs are driven by quantum Wiener processes of the external bosonic fields and are specified by the system Hamiltonian and system-field coupling operators. We consider the system response to perturbations in these operators and introduce a transverse Hamiltonian which encodes the propagation of the perturbations through the unitary system-field evolution. This approach provides an infinitesimal perturbation analysis tool which can be used for the development of optimality conditions in quantum control and filtering problems. Such settings employ, as performance criteria, quadratic (or more complicated) cost functionals of the system and field variables to be minimised over the energy and coupling parameters of system interconnections. We demonstrate an application of the transverse Hamiltonian variational approach to a mean square optimal coherent quantum filtering problem for a measurement-free field-mediated cascade connection of a quantum system with a quantum observer.

We compare Chiral Perturbation Theory (ChPT) and the Linear Sigma Model (LSM) as realizations of low energy QCD for light mesons in a chirally imbalanced medium. The relations between the low-energy constants of the Chiral Lagrangian and the corresponding constants of the Linear Sigma Model are established as well as the expressions for the decay constant of $\pi $-meson in the medium and for the mass of the $a_0$. In the large $N_c$ count taken from QCD the correspondence of ChPT and LSM is remarkably good and give a solid ground for search of chiral imbalance manifestation in pion physics. A possible experimental detection of chiral imbalance (and therefore a phase with Local Parity Breaking) is outlined in the charged pion decays inside the fireball.

The Italian herbal products market is the most prosperous in Europe. The proof is represented by the use of these products in several marketing categories, ranging from medicine to nutrition and cosmetics. Market and legislation in Italy are at the same time cause and consequence of this peculiar situation. In fact, the legislation on botanical food supplements in Italy is very permissive and at the same time the market shows an overall satisfaction of users and strong feedback in terms of consumption, which brings a widening use of medicinal plants, formerly the prerogative of pharmaceuticals, to other fields such as nutrition. This review summarizes the market and normative panorama of herbal products in Italy, highlighting the blurred boundaries of health indications, marketing authorizations and quality controls between herbal medicines and non pharmaceutical products, such as food supplements, cosmetics and other herbal-based “parapharmaceuticals”.

Biomimetic materials are substances that replicate natural structures. There are several methods for producing such materials with highly developed surfaces from a wide range of polymers, but electrospinning is of particular interest due to its simplicity of implementation and the ability to modify the produced fibrous materials resembling structures found in living organisms. This study explores new biomimetic materials based on polyhydroxyalkanoates, specifically poly-3-hydroxybutyrate, modified with chlorophyll derivatives. The research investigates the impact of chlorophyll derivatives on the morphology, supramolecular structure, and key properties of nonwoven materials. The obtained results are of interest for the development of new biomimetic environmentally friendly materials for biomedicine with special properties.

Many spectroscopic diagnostics are routinely used as a technique to infer the plasma parameters from line emission spectra but their accuracy depends on the numerical model or code used for the fitting process. However, the validation of a line shape code requires some steps : comparison of the line shape code with other similar codes for some academic (simple) cases and then more complex ones, comparison of the fitting parameters obtained from the best fit of the experimental spectra with those obtained with other diagnostic techniques and/or comparison of the fitting parameters obtained by different codes to fit the same experimental data. Here we compare the profiles of the hydrogen Balmer β line in a helium plasma computed by six codes for a selected set of plasma parameters and we report on the plasma parameters inferred by each of them from the fitting to a number of experimental spectra measured in a helium corona discharge where the pressure was in the range 1- 5 bar.

This paper reviews several techniques, including analytical theories and real frequency techniques, to design ultra-wideband impedance matching networks for low-power applications. The comparison of solutions obtained using the simplified real frequency technique to the published solution using Chebyshev filter theory is demonstrated.

. The impedance change of an induction coil surrounding a metal tube adapter is investigated by the truncated region eigenfunction expansion (TREE) method. Conventional TREE method is inapplicable to this problem as a consequence of the numerical overflow of eigenfunctions of the air-metal multi-subdomain regions. The difficulty is surmounted by a normalization procedure for the numerical eigenfunctions obtained from the finite element method (FEM). Efficient algorithm is devised by the Clenshaw-Curtis quadrature rule for integrals involving the numerical eigenfunctions. Numerical results of the TREE and FEM simulation coincide very well in all cases, and the efficiency of the proposed method is also confirmed.

A great improvement in food safety and quality controls worldwide has been achieved through the development of biosensing platforms. Foodborne pathogens continue to cause serious outbreaks due to the ingestion of contaminated food. The development of new, sensitive, portable, high-throughput, and automated platforms is a primary objective to allow detection of pathogens and their toxins in foods. Listeria monocytogenes is one common foodborne pathogen. Major outbreaks of listeriosis have been caused by a variety of foods, including milk, soft cheeses, meat, fermented sausages, poultry, seafood and vegetable products. Due to its high sensitivity and easy setup, electrochemical impedance spectroscopy (EIS) has been extensively applied for biosensor fabrication and in particular in the field of microbiology as a mean to detect and quantify foodborne bacteria. Here we describe a miniaturized, portable EIS platform consisting of a microfluidic device with EIS sensors for the detection of L. monocytogenes in milk samples, connected to a portable impedance analyzer for on-field application in clinical and food diagnostics but also for biosecurity purposes. To achieve this goal microelectrodes were functionalized with antibodies specific for L. monocytogenes. The binding and detection of L. monocytogenes was achieved in the range 2.2 x 103 cfu/ml to 1 x 102 with a Limit of Detection (LoD) of 5.5 cfu/ml.

This paper investigates the roll parameter estimation of periodic disturbances where the amplitude, frequency, offset, and phase are hardly recognized in real practice. The key problem is to make an estimation that could eliminate the unknown disturbance parameters. An adaptive mechanism applies these four parameters to the globally exponential convergence using linear second-order filters and parameter estimation errors. Then, a backstepping controller is employed to make an exponential convergence to zero of the state variables. Moreover, reservoir computing is used to forecast chaotic roll motions to support predictability using Lyapunov exponents and the Poincaré map. Numerical simulations are demonstrated to validate the dynamical behaviors and efficacy of the proposed control scheme with machine learning.

The power function distribution is a flexible waiting time model that may provide better fit for some failure data. This paper presents the comparison of the maximum likelihood estimates and the Bayes estimates of two-parameter power function distribution. The Bayes estimates are obtained, using conjugate priors, under five loss functions consist of square error, precautionary, weighted, LINEX and DeGroot loss function. The Gibbs sampling algorithm is proposed to generate samples from posterior distributions and in result the Bayes estimates are computed. The comparison of the maximum likelihood estimates and the Bayes estimates are done through the root mean squared errors. One real-life data set is analyzed to illustrate the evaluation of proposed methods of estimation. Finally, results from the simulation are discussed to assess the performance behavior of the maximum likelihood estimates and the Bayes estimates.

Sports video analysis is an interesting and emerging field in the domain of computer vision. It has become a very popular subject among scholars all over the world in the last decade due to the need of automated classification of events such as offsides, in/out situations, goals and so on. The most important problem in sports video analysis is detection and tracking of ball and players. Extraction of court lines is also another important problem since it is necessary in the classification of aforementioned events. In this study, considering some of the previous work on the subject, we develop a method for tracking the ball and players in tennis videos where the camera position and orientation is supposed fixed.

The occurrence and intensity of the detonation phenomenon at spark-ignition (SI) engine conditions is investigated, with the objective to successfully predict super-knock and to elucidate the effect of kinetics and transport at the ignition front. The computational singular perturbation (CSP) framework is employed in order to investigate the chemical and transport mechanisms of deflagration and detonation cases in the context of 2D high-fidelity numerical simulations. The analysis revealed that the detonation development is characterized by: (i) stronger explosive dynamics and (ii) enhanced role of convection. The role of chemistry was also found to be pivotal to the detonation development which explained the stronger explosive character of the system, the latter being an indication of the system's reactivity. The role of convection was found to be enhanced at the edge of the detonating front, thereby suggesting that it is the result and not the cause of the detonation onset. Moreover, the increased contribution of convection was found to be related mainly to heat convection. Remarkably, the detonation front was mainly characterized by dissipative and not explosive dynamics. Finally, diffusion was found to have negligible role to both examined cases.

A novel quasi-twisted miniaturized wideband Branch Line Coupler (BLC) is proposed. The design is based on bisecting the conventional microstrip line BLC transversely and folding bisected sections on double-layered substrates with a common ground plane in between. The pair of quarter wavelength horizontal parallel arms is converted to a Z-shape meandered microstrip line in the designed structure. On the other hand, the pair of quarter wavelength vertical arms are cut by half into two lines and converted to a periodically loaded slow wave structure. The bisected parts of BLC are placed on the opposite side of the doubled-layer substrate and connected through four vias passing through the common ground plane. This technique enabled a compact BLC size of 6.4×18 mm2, which corresponds to a surface area miniaturization by ~50% as compared to the classical BLC size of 10×23 mm2 at 6GHz, Moreover, the attained relative bandwidth is 73.9% (4.6-10 GHz) for S11, and 75.8% (4.5-10 GHz) for S33 as compared to 41% for the ordinary BLC at the same resonant frequency. The circuit is constructed on a double-layered low-cost FR4 substrate with a relative permittivity of 4.3, and a loss tangent of 0.025. An isolation of -13dB was realized in both S13 and S31 demonstrating an excellent performance. The transmission coefficients between input/output ports S21, S41, S23, and S43 are between -3.1dB to -3.5dB at the frequency of 6GHz. Finally, the proposed BLC provides phase differences between output ports of 90.5o and 94.8o at the frequency of 6GHz when the input ports 1 and 3 are excited, respectively. The presented design offers the potential of being utilized as a unit cell for building a Butler-matrix (BM) for sub-6GHz 5G beamforming networks.

The signature of chaotic systems can be characterized either by the sensitivity of the initial conditions or by the change of its parameters. This feature can be used for manufacturing high sensitivity sensors. Sensors based on chaotic circuits have already been used for measuring water salinity, inductive effects, and both noise and weak signals. This article investigates an impedance sensor based on the Van der Pol and Duffing damped oscillators. The calibration process is a key point and therefore the folding behavior of signal periods was also explored. A sensitivity of 0.15 kΩ/Period was estimated over a range from 89.5 to 91.6 kΩ. This range can be adjusted according to the application by varying the gain of the operational amplifier used in this implementation. The development of this type of sensor might be used in medical and biological engineering for skin impedance measurements, for example. This type of chaotic sensor has the advantage of sensing small disturbances and then detect small impedance changes within biological materials which, in turn, may not be possible with other detectors.

Hepatocellular carcinoma (HCC) is a heterogeneous malignancy with complex carcinogenesis. Although there has been significant progress in the treatment of HCC over the past decades, drug resistance to chemotherapy remains a major obstacle in its successful management. In this study we were able to reduce chemoresistance in cisplatin-resistant HepG2 cells by either silencing the expression of transglutaminase type 2 (TG2) using siRNA or by pre-treatment of cells with the TG2 enzyme inhibitor cystamine. Further analysis revealed that, whereas the full-length TG2 isoform (TG2-L) was almost completely cytoplasmic in its distribution, the majority of the short TG2 isoform (TG2-S) was membrane-associated in both parental and chemoresistant HepG2 cells. Following induction of cisplatin toxicity in non-chemoresistant parental cells, TG2-S together with cisplatin quickly relocated to the cytosolic fraction. Conversely, no cytosolic relocalisation of TG2-S or nuclear accumulation cisplatin was observed following identical treatment of chemoresistant cells, where TG2-S remained predominantly membrane-associated. This suggests that deficient subcellular relocalisation of TG2-S from membranous structures into the cytoplasm may limit the apoptic response to cisplatin toxicity in chemoresistant cells. Structural analysis of TG2 revealed the presence of binding motifs for interaction of TG-S with the membrane scaffold protein LC3/LC3 homologue that could contribute to a novel mechanism of chemotherapeutic resistance in HepG2 cells.

Dampers provide safety by control of unwanted motion, due to conversion of mechanical work into another form of energy (e.g., heat). State of the art materials are elastomers including thermoplastic-elastomers. For polymer-appropriate replacement of multi-component shock absorbers comprising mounts, rods, hydraulic fluids, pneumatic devices, or electro-magnetic devices, among others, deep insights of the dynamic thermo-mechanical characteristics of damper materials have to be gained. The ultimate objective is to reduce complexity by utilizing inherent material damping rather than structural (multi-component) damping properties. The objective of this work was to compare the damping behavior of different elastomeric materials including thermoplastic poly(urethane) (TPU), and silicone rubber blends (mixtures of different poly(dimethylsiloxane) (PDMS)). Therefore, the materials were hyper- and viscoelastic characterized, a finite element calculation of a ball-drop test was performed, and for validation the rebound resilience was measured experimentally. In an attempt, the coil-over shock absorber of a model car was replaced by a damper made of the examined and modeled materials. The results revealed that the material parameter determination methodology is reliable, and the data applied for simulation lead to realistic predictions. Interestingly, the rebound resilience of the mixture of soft and hard PDMS (50:50)w% is the highest and the lowest values were measured for TPU.

This article introduces a new MfEIT UDESC Mark I system, which consists of a 32-electrode setup featuring a modified Howland current source, low cost, portable and non radiation. The system is capable of reconstruction of electrical conductivity tomographic images at a rate of 30.624 frames per second and about 5 minutes for imaging. The current source employs 0.5 mA, adjacent current application pattern with frequencies ranging from 10 kHz to 1 MHz. The article outlines the hardware, firmware, and software design specifications, which include the design of the current source, calibration procedures, and image reconstruction process. Tomographic images of conductivity were reconstructed in ex vivo healthy pig lungs and those with pneumonia, as a proof of concept for future applications in live pigs. The high spectral power density, combined with real-time system calibration provides clinical advantages in veterinary medicine. The goal is to identify lung areas affected by Mycoplasma hyopneumoniae in pigs, through the analysis of electrical conductivity difference, offering a valuable tool to assist veterinarians for to obtain images of respiratory diseases. The reconstruction method (GREIT) was evaluated with experimental data and It was compared with the Gauss-Newton and Total Variation methods, where GREIT proved to be superior.

In this paper, the entire downhole fluid sucker rod pump system is replaced with a viscoelastic vibration model, namely a third-order differential equation with an inhomogeneous forcing term. Both Kelvin and Maxwell viscoelastic models can be implemented along with the dynamic behaviors of a mass point attached to the viscoelastic model. By employing the time-dependent polished rod force measured with a dynamometer as the input to the viscoelastic dynamic model, we have obtained the displacement responses, which match closely with the experimental measurements in actual operations, through an iterative process. The key discovery of this work is the feasibility of the so-called inverse optimization procedure which can be utilized to identify the equivalent scaling factor and viscoelastic system parameters. The proposed Newton-Raphson iterative method with some terms in the Jacobian matrix expressed with averaged rates of changes based on perturbations of up to two independent parameters provides a feasible tool for optimization issues related to complex engineering problems with mere information of input and output data from either experiments or comprehensive simulations. The same inverse optimization procedure is also implemented to model the entire fluid delivery system of a very viscous non-Newtonian polymer modeled as a first-order ordinary differential system similar to the transient entrance developing flow. The convergent parameter reproduces transient solutions which match very well with those from full-fledged computational fluid dynamics models with the required inlet volume flow rate and the outlet pressure conditions.

Symmetry concepts in parametrized dynamical systems may reduce the number of external parameters by a suitable normalization prescription. If, under the action of a symmetry group G, parameter space A becomes a (locally) trivial principal bundle, A ~ A/G x G, then the normalized dynamics only depends on the quotient A/G. In this way, the dynamics of fractional variables in homogeneous epidemic SI(R)S models, with standard incidence, absence of R-susceptibility and compartment independent birth and death rates, turns out to be isomorphic to (a marginally extended version of) Hethcote's classic endemic model, first presented in 1973. The paper studies a 10-parameter master model with constant and I -linear vaccination rates, vertical transmission and a vaccination rate for susceptible newborns. As recently shown by the author, all demographic parameters are redundant. After adjusting time scale, the remaining 5-parameter model admits a 3-dimensional abelian scaling symmetry. By normalization we end up with Hethcote's extended 2-parameter model. Thus, in view of symmetry concepts, reproving theorems on endemic bifurcation and stability in such models becomes needless.

This article aims to assess, discuss and analyze the disturbances caused by electromagnetic field (EMF) noise of medical devices used nearby living tissues, as well as the corresponding functional control via the electromagnetic compatibility (EMC) of these devices. These are minimally invasive and non-ionizing devices allowing various healthcare actions involving monitoring, assistance, diagnosis and image-guided medical interventions. Following to an introduction of the main items of the paper, the different imaging methodologies are conferred, accounting for their nature, functioning, employment condition and patient comfort and safety. Then the magnetic resonance imaging (MRI) components and their fields, the consequential MRI-compatibility concept and possible image artifacts are detailed and analyzed. Next, the MRI-assisted robotic treatments, the possible robotic external matter introductions in the imager, the features of MRI-compatible materials and the conformity control of MRI-compatibility, are analyzed and conferred. Afterward, the embedded, wearable and detachable medical devices, their EMF perturbation control and their necessary shielding protection technologies are presented and analyzed. Then, the EMC control procedure, the EMF governing equations, the body numerical virtual models, are conferred and reviewed. A qualitative methodology, case study, simple example illustrating the mentioned methodology is presented. The last Section of the paper discussed potential details and expansions of the different notions conferred in the paper, in the perspective of monitoring the disturbances due to EMF noise of medical devices working near living tissues.

In recent, Chae found that, at weak gravitational acceleration g_N≲10⁻⁹ms⁻², the observed orbit of the wide binary stars is not accordant with current theory of binary star. Here, we present, this finding should be an observational evidence for that Newtonian theory of orbit perturbation is still valid in galactic scale.

Model understanding is critical in many domains, particularly those involved in high-stakes decisions, i.e., medicine, criminal justice, and autonomous driving. Explainable AI (XAI) methods are essential for working with black-box models such as Convolutional Neural Networks. This paper evaluates the traffic sign classifier of Deep Neural Network (DNN) from the Programmable Systems for Intelligence in Automobiles (PRYSTINE) project for explainability. The results of explanations were further used for the CNN PRYSTINE classifier vague kernels` compression. After all, the precision of the classifier was evaluated in different pruning scenarios. The proposed classifier performance methodology was realised by creating the original traffic sign and traffic light classification and explanation code. First, the status of the kernels of the network was evaluated for explainability. For this task, the post-hoc, local, meaningful perturbation-based forward explainable method was integrated into the model to evaluate each kernel status of the network. This method enabled distinguishing high and low-impact kernels in the CNN. Second, the vague kernels of the classifier of the last layer before the fully connected layer were excluded by withdrawing them from the network. Third, the network's precision was evaluated in different kernel compression levels. It is shown that by using the XAI approach for network kernel compression, the pruning of 5% of kernels leads only to a 1% loss in traffic sign and traffic light classification precision. The proposed methodology is crucial where execution time and processing capacity prevail.

The discovery by the Large Area Telescope on board Fermi of variable gamma-ray emission from radio-loud narrow-line Seyfert 1 (NLSy1) galaxies revealed the presence of a possible third class of AGN with relativistic jets in addition to blazars and radio galaxies. Considering that NLSy1 are usually hosted in spiral galaxies, this finding poses intriguing questions about the nature of these objects and the formation of relativistic jets. We report on a systematic investigation of the gamma-ray properties of a sample of radio-loud NLSy1, including the detection of new objects, using 7 years of Fermi-LAT data with the new Pass 8 event-level analysis. In addition we discuss the radio-to-very-high-energy properties of the gamma-ray emitting NLSy1, their host galaxy, and black hole mass in the context of the blazar scenario and the unification of relativistic jets at different scales.

The strictness of the result of an excavation, whether mechanical or by means of explosives, is naturally conditioned by the objective, and therefore by the type of technique applied to achieve it. To attain the best results in terms of rock breakage and respect of the final profile, it’s important to evaluate the excavation specific energy and its optimization. This research focuses on evaluating the effects of different techniques on the quality of final walls in open-pit and underground operations. Different geometries and configurations can be applied to both quarrying and tunnelling blasts. The research is aimed to push contour blasts to their limits, and the main aspects are discussed in order to improve the blast parameters in the daily practice.

Background: Electrical Impedance Tomography (EIT), combined with variable ventilation strate-gies and Artificial Intelligence (AI), is poised to revolutionize critical care by transitioning from reactive to predictive approaches. This integration aims to enhance patient outcomes through personalized interventions and real-time monitoring. Methods: This narrative review explores the principles and applications of EIT, variable ventilation, and AI in critical care. EIT’s impedance sensing creates dynamic images of internal physiology, aiding in the management of conditions like Acute Respiratory Distress Syndrome (ARDS). Variable ventilation mimics natural breathing variability to improve lung function and minimize ventilator-induced lung injury. AI enhances EIT through advanced image reconstruction techniques, neural networks, and digital twin technology, offering more accurate diagnostics and tailored therapeutic interventions. Conclu-sions: The confluence of EIT, variable ventilation, and AI represents a significant advancement in critical care, enabling a predictive, personalized approach. EIT provides real-time insights into lung function, guiding precise ventilation adjustments and therapeutic interventions. AI inte-gration enhances EIT's diagnostic capabilities, facilitating the development of personalized treatment plans. This synergy fosters interdisciplinary collaborations and sets the stage for in-novative research, ultimately improving patient outcomes and advancing the future of critical care.

Our objective was to investigate the effects of topically applied neuropeptide Y (NPY) on ischemic wounds. Initially, the animal model for ischemic wound healing was validated using 16 male Sprague-Dawley albino rats. In the intervention study, an additional 28 rats were divided into three groups: NPY (0.025%), the positive control insulin-like growth factor-I (IGF-I, 0.0025%), and the hydrogel carrier alone (control). The hydrogel was selected due to its capacity to prolong NPY release (p &lt; 0.001), as demonstrated in a Franz diffusion cell. In the animals, an 8-mm full-thickness wound was made in a pedunculated dorsal ischemic skin flap. Wounds were then treated and assessed for 14 days, and procured at the end of the experiment for in situ hybridization analysis (RNAscope®) targeting NPY receptor Y2R and for meticulous histologic examination. Wound healing rates, i.e. the percentage wound area changes, did not show an increase with NPY (p = 0.938) but did with rhIGF-I (p = 0.039) compared to the control. Y2R mRNA was not detected in the wounds or adjacent skin but was identified in the rat brain (positive control). Light microscopic examination revealed trends of increased angiogenesis and enhanced inflammatory cell infiltration with NPY compared to control. An interesting secondary discovery was the presence of melanophages in the wounds. Our findings suggest the potential of NPY to enhance neovascularization under ischemic wound healing conditions, but further optimization of the carrier and dosage is necessary. The mechanism is elusive but likely involves NPY receptor subtypes other than Y2R.

Modern agent-based models (ABM) and other simulation models require evaluation and testing of many different parameters. Managing that testing for large scale parameter sweeps (grid searches) as well as storing simulation data requires multiple, potentially customizable steps that may vary across simulations. Furthermore, parameter testing, processing, and analysis are slowed if simulation and processing jobs cannot be shared across teammates or computational resources. While high-performance computing (HPC) has become increasingly available, models can often be tested faster through the use of multiple computers and HPC resources. To address these issues, we created the Distributed Automated Parameter Testing (DAPT) Python package. By hosting parameters in an online (and often free) "database", multiple individuals can run parameter sets simultaneously in a distributed fashion, enabling ad hoc crowdsourcing of computational power. Combining this with a flexible, scriptable tool set, teams can evaluate models and assess their underlying hypotheses quickly. Here we describe DAPT and provide an example demonstrating its use.

Distributed Energy Resources might have a severe influence on Power Line Communications, as they can generate interfering signals and high frequency emissions or supraharmonics that may cause loss of metering and control data. In this paper, the influence of various energy resources on Narrowband Power Line Communications is described and analyzed through several test measurements performed in a real microgrid. Accordingly, the paper describes the effects on smart metering communications through MAC layer analysis. Results show that the commutation frequency of inverters and the presence of battery chargers are remarkable sources of disturbance in low voltage distribution networks. In this sense, the results presented can contribute to efforts towards standardization and normative of emissions at higher frequencies higher, such as CENELEC EN 50160 and IEC/TS 62749.

Accurate evaluation of health status of lithium-ion batteries must be deemed as of great significance, insofar as utility and safety of batteries are of concern. Lithium plating, in particular, is notoriously known to be a chemical reaction that can cause deterioration in, or even fatal hazards to, the health of lithium-ion batteries. Electrochemical impedance spectroscopy (EIS), which has distinct advantages such as fast or non-destructive over its competitors, suffices in detecting lithium plating and thus has been attracting increasing attention in the field of battery management, but its ability of assessing quantitatively the degree of lithium plating remains largely unexplored hitherto. On this point, this work seeks to narrow that gap, by proposing an EIS-based method that can quantify the degree of lithium plating. The core conception is to eventually circumvent the reliance on state-of-health measurement, and use instead the impedance spectrum, to acquire an estimate on battery capacity loss. To do so, the effects of solid electrolyte interphase formation and lithium plating on battery capacity must be first decoupled, so that the mass of lithium plating can be quantified. Then, based on an impedance spectrum measurement, the parameters of the fractional equivalent circuit model (ECM) of the battery can be identified. These fractional ECM parameters are received as inputs by an artificial neural network, which is tasked to establish a correspondence between the model parameters and the mass of lithium plating. The empirical part of the work revolves around the data collected from an aging experiment, and the validity of the proposed method is truthfully attested by dismantling the batteries, which is otherwise not needed during the actual uptake of the method.

A novel configuration for a super-wide impedance planar antenna is presented based on a 2 × 2 microstrip patch antenna (MPA). The antenna comprises a symmetrical arrangement of four-square patches that are interconnected to each other with cross-shaped high impedance microstrip lines. The antenna array is exciting through a single feedline connected to one of the patches. The proposed antenna array configuration overcomes the main drawback of conventional MPA of narrow bandwidth that is typically <5%. The antenna exhibits a super-wide frequency bandwidth from 20 GHz to 120 GHz for S₁₁<−15 dB, which corresponds to a fractional bandwidth of 142.85%. The antenna’s performance of bandwidth, impedance match, and radiation gain were enhanced by etching slots on the patches. The slotted microstrip patch essentially acts like a left-handed capacitance to exhibit metamaterial properties over a given frequency range. With the inclusion of the slot the maximum radiation gain and efficiency of the MPA have increased to 15.11 dBi and 85.79% at 80 GHz, which show an improvement of 2.58 dBi and 12.54%, respectively. The dimension of each patch antenna is 30 × 30 mm². The results show that the proposed MPA is useful for various communications existing and emerging systems such as ultra-wideband (UWB) communications, RFID systems, massive multiple-output multiple-input (MIMO) for 5G, and radar systems.

Many people in the USA have lost their lives or become addicted to opioids via prescription opioids given for chronic pain. The chronic pain epidemic has emerged due to a convergence of factors, including the medicalization of pain as well as injuries happening in the workplace, in the home, or during recreation. Opioid prescriptions rose precipitously from the late 1990’s through to approximately 2020, and despite public awareness, still are increasing. This review examines literature on integrative approaches to chronic pain as delineated by pain type. The review is organized by the most common causes of chronic pain, and randomized controlled trials, meta-analyses and systematic reviews are extracted for each cause of chronic pain. Several promising interventions may alleviate chronic pain of some causes, and some interventions may work across pain causes. Lowering inflammation through dietary or lifestyle regimens may be a general way of reducing pain. Pain can be alleviated through several adjunctive and integrative treatment approaches, which may serve to lower the need for opioid medication.

The new hybrid composite materials for PEM fuel cell were synthesized by UV-polymerization of acrylic monomers (acrylonitrile (AN), acrylic acid (AA), ethylene glycol dimethacrylate (EGDMA)) and sulfo aromatic monomer – sodium styrene sulfonate (SSS), and tetraethoxysilane/3-methacryloxypropyltrimethoxysilane (TEOS/MAPTMS)-based sol-gel system. By means of X-ray spectroscopy fractal structure of the obtained materials was characterized. Proton conductivity and viscoelastic properties of the materials were investigated depending on the content of inorganic component in nanocomposites. On the basis of impedance studies, an equivalent scheme is proposed that successfully describes the proton conductivity in the synthesized composite electrolyte membranes.

The unreliable prediction of the low frequency components from inverted acoustic impedance causes uncertainty in quantitative seismic interpretation. To address this issue, we first calculate various seismic and geological attributes that contain low frequency information, such as relative geological age, interval velocity, and integrated instantaneous amplitude. Then, we develop a method to predict the low frequency content of seismic data using these attributes, their high frequency components, and recurrent neural networks. Next, we test how to predict the low frequency components using stacking velocity obtained from velocity analysis. Using all the attributes and seismic data, we propose a supervised deep learning method to predict the low frequency components of the inverted acoustic impedance. The results obtained in both synthetic and real data cases show that the proposed method can improve the prediction accuracy of the low frequency components of the inverted acoustic impedance, with the best improvement in a real data example of 57.7% compared with the impedance predicted using well log interpolation.

Acoustic energy dissipates in multi-phase or multi-boundary materials. Hybrid composites are described as multi-phase with many interfaces between their materials. The current research proposes studying the acoustic behavior of polymeric hybrid composites by estimating the time, velocity, and hybrid composite acoustic impedance. Two groups of hybrid composites were prepared, including unsaturated polyester with PMMA, except one with HDPE and the other with PS. Each group has 28, 35, and 40% weight fractions. An ultrasonic test measured time to determine velocity and acoustic impedance later. The results show that increasing the weight fraction will increase density with respect to the density of the reinforcing material. Different ultrasonic times were obtained with increasing weight fractions. As the weight fraction of PS increased, the time increased; unlike the velocity, it decreased but increased with density. In contrast, this behavior was changed if the hybrid had PE. The highest acoustic impedance was at 28% UP/PMMA+PS. In conclusion, UP/PMMA+PS can dissipate ultrasonic waves more than UP/PMMA+PE.

A portable, electrical impedance spectroscopy device to monitor the bioimpedance’s resistive component of beef meat by injecting a sinusoidal current of 1mA at 65.5 kHz was developed. In 4 slaughtered beef both right and left longissimus dorsi muscles where trimmed and left muscle portion was frozen to -18° C up to 7^th day while right one was meantime maintained at 5° C. Median value of specific resistivity of not-frozen sample was about twice Ω cm^-1 with respect of that of frozen-thawed sample (P = 0.004). It was concluded that the device is reliable to monitoring the ripening of beef meat in situ.

Circadian rhythm disruption is increasingly considered an environmental risk factor for the development and exacerbation of inflammatory bowel disease. We have reported in a previous study that nychthemeral dysregulation is associated with an increase in intestinal barrier permeability and inflammation in mice with dextran sulfate sodium (DSS)-induced colitis. To investigate the effect of circadian rhythm disruption on the composition and diversity of the gut microbiota (GM). Sixty male C57BL/6J mice were divided initially to two groups, the shifted group (n=30) exposed to circadian shifts for three months and the non-shifted group (n=30) under a normal light-dark cycle. The mice of the shifted group were cyclically housed for five days under the normal 12:12 hour light-dark cycle followed by another five days under reversed light-dark cycle. At the end of the three months a colitis was induced by 2 % DSS given in the drinking water of 30 mice. Animals were then divided into four groups (n=15 per group), sham group non-shifted (Sham-NS), sham group shifted (Sham-S) and DSS non-shifted (DSS-NS) and DSS shifted (DSS-S). Fecal samples were collected from rectal content to investigate changes in GM composition by DNA extraction followed by high-throughput sequencing of the bacterial 16S rRNA gene. The mouse GM was dominated by three phyla: Firmicutes, Bacteroidetes and Actinobacteria. The Firmicutes/Bacteroidetes ratio decreased in mice with induced colitis. The richness and diversity of the GM were reduced in the colitis group, especially in the group with inverted circadian rhythm. Moreover, GM composition was also modified in the inverted circadian rhythm group, with an increase in Alloprevotella, Turicibacter, Bacteroides and Streptococcus genera. Circadian rhythm inversion exacerbates GM dysbiosis to a less rich and diversified extent in a DSS-induced colitis model. These findings shows a possible interplay between circadian rhythm disruption, GM dynamics, and colitis pathogenesis.

This paper proposes a novel model for a PV cell with parameters variance dependency on temperature and irradiance included. The model relies on commercial available data, calculates the cell parameters for standard conditions and then extrapolates them for the whole operating range. An up-to-date review of the PV modeling is also included with series and parallel parasitic resistance values and dependencies discussed. The parameters variance is analyzed and included in the proposed PV model, where the self-heating phenomenon is also considered. Each parameter variance is compared to the results from different authors. The model includes only standard components and can be run on any SPICE-based simulator. Unlike other approaches that consider the internal temperature as a parameter, our proposal relies on air temperature as an input and computes the actual internal temperature accordingly. Finally, the model is validated via experiments and comparisons to similar approaches are provided.

(1) Background: To estimate resistance, reactance and phase angle values among moderate preterm infants and their variation according to neonatal and maternal characteristics and nutritional intake. (2) Methods: This was a cohort that evaluated 43 moderate preterm infants using bioelectrical impedance analysis. The study variables included resistance, reactance and PA measurements, in addition to classification of nutritional intake. (3) Results: The mean resistance was 602.0+118.2 Ω, reactance was 57.2 Ω (IIQ = 42.6-65.2) and phase angle was 522° (IIQ = 4.1-6.6). Lower resistance values were found in the presence of risky pregnancy (532.2+111.9 Ω vs 650.9+97.9 Ω, p&lt;0.001) and lower reactance values, in the presence of harmful maternal lifestyle habits at both the first (p=0.01) and second assessments (p=0.01). Eight preterm infants were considered to have insufficient nutritional intake (23.5%); 17, sufficient (50.0%) and 9, partially sufficient (26.5%). There was less reactance among preterm infants with insufficient nutritional intake (p &lt; 0.001). (4) Conclusions: The bioelectrical impedance analysis measurements were within the range of values reported in other studies. There was an association between full diet and adequate nutritional intake with higher resistance values, and a lower reactance value was associated with the presence of risky pregnancy and harmful maternal lifestyle.

This paper addresses the parameter identification of a one-link flexible manipulator based on the experimental measurement of the inputs/outputs, the finite element model, and the application of evolutionary algorithms. A novel approach is proposed to find the values of inertia, stiffness, and damping parameters by minimizing the difference between the numerical model’s outputs and the testbed’s outputs, considering the joint position and acceleration of the link’s tip. The dynamic model is initially obtained using the finite element method and the Lagrange principle. A prototype of a single one-link flexible manipulator is used in the experimental application wherein the servomotor applies the input torque, and the outputs are the joint angle and the link’s tip acceleration. Then, an optimization problem minimizes the difference between numerical and experimental outputs to determine the set of parameters using evolutionary algorithms. A comparative analysis to obtain the identified parameters is established using genetic algorithms, particle swarm optimization, and differential evolution. The proposed identification approach permitted the determination of the dynamic parameters based on the complete dynamic model of the flexible-link manipulator, which is different from the approaches reported in the literature that identify a simplified model. This information is essential for the design of the motion and vibration control laws.

Estimating the parameters of statistical distributions generally involves solving a system of nonlinear equations or a nonlinear equation, being a technical difficulty in their usual application in hydrology. This article presents improved approximations and, in some cases, new approximations for the estimation with the method of ordinary moments and the method of linear moments, which are useful for the direct calculation of the parameters, because the errors in the approximate estimation are similar to the use of iterative numerical methods. Thirteen statistical distributions of two and three parameters frequently used in hydrology are presented, for which parameter estimation was laborious. Thus, the approximate estimation of the parameters by the two methods is simple but also precise and easily applicable by hydrology researchers. The approximate forms characterized by very small errors are the result of the research conducted within the Faculty of Hydrotechnics to update the romanian normative standards in the hydrotechnical field.

We introduce the Hermite based poly-Bernoulli polynomials with a q parameter and give someof their basic properties including not only addition property, but also derivative properties and integralrepresentations. We also de.ne the Hermite based λ -Stirling polynomials of the second kind, and thenprovide some relations. Moreover, we derive several correlations and identities including the Hermite-Kampéde Fériet (or Gould-Hopper) family of polynomials, the Hermite based poly-Bernoulli polynomials with a qparameter and the Hermite based λ -Stirling polynomials of the second kind.

Efficient quality evaluation provides support for the timely and good maintenance of the lane line marking. This paper searches and optimizes the back propagation(BP) network model which referred to the analytic hierarchy process(AHP) model structure, as well as the number of nodes in the middle layer network. Based on this, a comprehensive evaluation method of multi-dimensional lane line quality such as shape, color and contrast is established. The experimental results show that the parameters of the model are more simplified, and the scoring and classification results of lane lines are more accurate.

We provide a very general review of the resonant transmission line method for optical fiber problems. The method has been found to work seamlessly for a variety of difficult problems including elliptical and eccentric core fibers as well as “holey”, photonic crystal fibers. A latest version has been shown to offer great versatility with respect to cases of unconventional, inhomogeneous index profiles.

Electrochemical Impedance Spectroscopy (EIS) is a powerful non-invasive technique used to characterize Lithium-ion cells. Its application allows to identify and track the evolutions of cell degradation processes within a short testing time. This review collects all the available works which have used EIS spectra either to characterize Li-ion cell degradation or to develop Electric Circuit Models (ECMs). The objectives of this work are: (i) to highlight the influence of different aging test conditions on the EIS spectra; (ii) to find the correlations between EIS spectra variations and the underlying degradation mechanisms and (iii) to list the available options to formulate ECMs from EIS spectra of aged cells. After an exhaustive analysis of the state-of-the-art, a critical review is presented to discuss the existing links between degradation mechanisms and the most reliable solutions to model them.

Body composition measurement plays an important auxiliary role in the nutritional assessment of diseases, nutritional diagnosis and the evaluation of the effect of nutritional therapy. There are many techniques and methods available for the measurement of body composition. Bioelectrical impedance analysis (BIA ) of body composition has been widely used and explored in many diseases in the past 30 years. Its main advantages are its non-invasiveness, non-radiation, economy, convenience and feasibility. With the development of bioelectrical impedance technology, bioelectrical impedance analysis has gradually developed from single-frequency BIA (SF-BIA) to dual-frequency BIA (DF-BIA). now devices are available that measure at multiple fixed frequencies (multi-frequency BIA, MF-BIA) and over a range of frequencies (bioimpedance spectroscopy, BIS). The clinical significance of nutrition management in chronic kidney disease has gradually become prominent. Bioelectrical impedance analysis of body composition is favored by nephrologists and nutritionists as an auxiliary method for nutrition diagnosis, treatment and monitoring. In the past 20 years, there have been many studies on body composition measurement by bioelectrical impedance analysis in the nutritional management of CKD patients. This article will summarize the recent research results of BIA of body composition method in the nutrition management of CKD patients in pre-dialysis, hemodialysis, peritoneal dialysis and kidney transplantation, in order to provide reference for the application and research of BIA method in the nutrition management of chronic kidney disease in the future.

Electrical impedance tomography (EIT) can monitor the real-time hemodynamic state of a conscious and spontaneously breathing patient noninvasively. However, cardiac volume signal (CVS) extracted from EIT images has a small amplitude and is sensitive to motion artifacts (MAs). This study aimed to develop a new algorithm to reduce MAs from the CVS for more accurate heart rate (HR) and cardiac output (CO) monitoring in patients undergoing hemodialysis based on the source consistency between the electrocardiogram (ECG) and the CVS of heartbeats. Two signals were measured at different locations on the body through independent instruments and electrodes, but the frequency and phase were matched when no MAs. As the number of motions per hour (MI) increased over 30, the proposed algorithm had a correlation of 0.83 and a precision of 1.65 beats per minute (BPM) compared to the conventional statical algorithm of a correlation of 0.56 and a precision of 4.04 BPM. For CO monitoring, the precision and upper limit of the mean ∆CO were 3.41 and 2.82 liters per minute (LPM), respectively, compared to 4.05 and 3.82 LPM of the statistical algorithm. The developed algorithm could reduce MAs and improve HR/CO monitoring accuracy and reliability, particularly in high-motion environments.

Today’s intruders usually send attacking commands to a target system through several stepping-stone hosts, in order to reduce the chance of being detected. With stepping-stone intrusion (SSI), the intruder’s identity is hidden behind a long interactive chain of hosts and very hard to detect. An effective approach for SSI detection (SSID) is to estimate the length of the chain. This type of method is called network-based SSID. Most existing network-based SSID worked effectively only when intruders’ session manipulation was not present. These known SSID algorithms are either weak to resist intruders’ chaff-perturbation manipulation or having very limited capability in resisting attacker’s session manipulation. This paper develops a novel network-based SSID algorithm resistant to intruders’ chaff-perturbation by using packet crossover. Our proposed SSID algorithm is simple and easy to implement as the number of packet crossovers can be easily computed. We conduct rigorous technical proofs to verify the correctness of our proposed algorithm. The experimental results show that our proposed SSID algorithm works effectively and perfectly in resisting intruders’ chaff-perturbation up to 50% chaff rate.

A variable speed anti-tangling reel mechanism was designed to address the problems of tangling, hanging and rewinding of the tassel wheel and the high paddling loss in the current Chinese rape combine harvester cutting table. The kinematic equations of the reel mechanism were developed, and the analysis showed that the speed in the entry stage is low and the speed in the exit stage is high, and the attitude of the reel teeth change with the rape plant movement during the whole paddling process. A single-factor test and a multi-factor regression orthogonal combination test were carried out using the cutting table loss rate of rape harvesting as the evaluation index. The main and secondary factors affecting the cutting table loss of the variable speed reel were obtained as the reel speed, the machine travel speed and the ground angle of the frame. A mathematical model of regression of cutter loss and the main influencing factors was established, with the coefficient of determination R2 = 0.9918. The optimal combination of parameters for the variable speed reel was obtained with the lowest cutting table loss rate in rape harvesting as the optimization target: reel speed 25r/min, frame parallel to the ground and implement travel speed 0.7m/s. Field validation tests and comparative tests of cutting table loss of the two reels were carried out. The test results show that the regression mathematical model of the cutting table loss is more accurate, and the cutting table loss is reduced by 13.9% with the variable speed reel compared to the cam-action reel, and there are no problems with the paddle teeth hanging and tangling during the paddling process.

Functional Data Analysis (FDA) is a relatively new field of statistics dealing with data expressed in the form of functions. FDA methodologies can be easily extended to the study of imaging data, an application proposed in Wang et al. (2020), where the authors settle the mathematical groundwork and properties of the proposed estimators. This methodology allows for the estimation of mean functions and simultaneous confidence corridors (SCC), also known as simultaneous confidence bands, for imaging data and for the difference between two groups of images. This is especially relevant for the field of medical imaging, as one of the most extended research setups consists on the comparison between two groups of images, a pathological set against a control set. FDA applied to medical imaging presents at least two advantages compared to previous methodologies: it avoids loss of information in complex data structures and avoids the multiple comparison problem arising from traditional pixel-to-pixel comparisons. Nonetheless, computing times for this technique have only been explored in reduced and simulated setups (Arias-López et al., 2021). In the present article, we apply this procedure to a practical case with data extracted from open neuroimaging databases and then measure computing times for the construction of Delaunay triangulations, and for the computation of mean function and SCC for one-group and two-group approaches. The results suggest that previous researcher has been too conservative in its parameter selection and that computing times for this methodology are reasonable, confirming that this method should be further studied and applied to the field of medical imaging.

Our skin epidermis constitutes the most important innate defense barrier against all pathogens. Therefore, even if skin lesions are common due to infections, scarring, genetic disorders, and other diseases, skin integrity is crucial for maintaining body homeostasis. Marine collagen peptides (MCPs) and Glycosaminoglycans (GAGs) have been described as potential wound healing (WH) agents. Recently, through an ex vivo clinical approach, we have demonstrated the nutricosmetic potential of fish cartilage hydrolysate (FCH), which presents a combination of collagen peptides and GAGs. Here, we coupled a clinical approach with in vitro experiments on human dermal fibroblasts (HDFs) and applied a Data Independent Acquisition - Parallel Accumulation Serial Fragmentation (diaPASEF) proteomic analysis, to assess the potential benefit of FCH in WH and its mode of action. Our results show that human serum enriched with circulating metabolites resulting from FCH ingestion, improved wound closure in scratch assays. In support, some proteins with anti-inflammatory and immunomodulatory properties or prone to promote hydration and extracellular matrix (ECM) stability showed increased expression in HDFs, after exposure to FCH-enriched serum. These findings suggest that FCH appears as a promising nutrient for WH and skin regeneration.

This paper presents a method to detect and classify the high impedance fault that occur in the medium voltage distribution network using discrete wavelet transform (DWT) and adaptive neuro-fuzzy inference system (ANFIS). The network is designed using Matlab software and various faults such as high impedance, symmetrical and unsymmetrical fault have been applied to study the effectiveness of the proposed ANFIS classifier method. This is achieved by training the ANFIS classifier using the features (standard deviation values) extracted from the three phase fault current signal by DWT technique for various cases of fault with different values of fault resistance in the system. The success and discrimination rate obtained for identifying and classifying the high impedance fault from the proffered method is 100% whereas the values are 66.7% and 85% respectively for conventional fuzzy based approach. The results indicate that the proposed method is more efficient to identify and discriminate the high impedance fault accurately from other power system faults in the system.