The conformity assessment of products or a measured value with the given standards is carried out based on the global risk of producers and consumers calculation. A product may conform to specifications but be falsely rejected as non-conforming. This is about the producer's risk. If a product doesn't meet the requirements but is falsely accepted as conforming, that poses a risk to the consumer. The conventional approach to risk assessment, which yields only a single numerical value for the global risk of producers and consumers, is naturally extended, and utilized for assessing risk in measurement models with linear regression. The outcomes of the two-dimensional extension, along a moderate scale, are the parabolas with an opening upwards. Risk surfaces were obtained through three-dimensional extension over the area limited by the moderate scale and guard band axes. Four models with different ranges of tolerance intervals were used to test this innovative method of risk assessment in linear regression. The corresponding standard measurement uncertainties are determined by applying a simplified measurement model with the use of comprehensive data on the measurement performance and by determining measurement uncertainty derived from consideration of the functional relationship obtained by linear regression analysis. Models that utilize information from linear regression analysis to determine measurement uncertainty are biased towards risks at the edges of the moderate scale. Testing the model's performances with metrics related to the confusion matrix, such as the F1 score, further substantiated this assertion. The diagnostic odds ratio has been proven to be extremely effective in identifying the curve along the guard band axis, along which the global risks of producers and consumers are at their lowest.

In this paper, we present a relapse based demonstrating way to deal with investigate various arrangement MTC information. A commonplace use of this displaying approach incorporates three stages: first, define a model that approximates the connection between quality articulation and trial factors, with boundaries consolidated to address the exploration premium; second, utilize least-squares and assessing condition methods to gauge boundaries and their relating standard blunders; third, register test insights, P-qualities and NFD as proportions of factual criticalness. The benefits of this methodology are as per the following. To begin with, it tends to the exploration interest in a particular, precise way, and maximally uses all the information and other important data. Second, it represents both orderly and irregular varieties related with the information, and the consequences of such examination give not just quality explicit data applicable to the exploration objective, yet additionally its dependability, in this way helping agents to settle on better choices for subsequent investigations. Third, this methodology is truly adaptable, and can undoubtedly be stretched out to different sorts of MTC considers or other microarray explores by detailing various models dependent on the test plan of the investigations.

With the use of linear regression modeling, this study sought to forecast and analyze rainfall patterns in Ethiopia. The dataset included historical rainfall data as well as pertinent independent variables. The R-squared score and mean squared error (MSE) were used to assess the effectiveness of the linear regression model. The results showed that the model's ability to forecast and analyze rainfall patterns was not very good. Only around 5.3% of the variance in rainfall could be explained by the chosen independent variables, according to the R-squared score of 0.053. This low number indicated that there was little correlation between the selected variables and rainfall, and that a sizable percentage of the variation in the dependent variable was not captured by the model. The model's accuracy in forecasting rainfall was shown to be quite low by the MSE error, with significant squared discrepancies between the expected and actual amounts. These results support the notion that the linear regression model as it is now designed is not appropriate for studying or forecasting Ethiopia's rainfall patterns. Alternative modeling approaches, the inclusion of other pertinent factors, and the assurance of the availability of high-quality data that faithfully captures the intricate dynamics of rainfall in the area all require more investigation.

This study investigates the suitability of the timestamp approach algorithm for predicting blood pressure (BP) using wearable and comfortable devices, showcasing its accuracy even with low-frequency sampled signals. Developed within the SINTEC European project, the algorithm utilizes Electrocardiogram (ECG) and Photoplethysmogram (PPG) sensors, demonstrating promising results in both laboratory and hospital settings. The research emphasizes the algorithm’s potential to transform continuous and non-invasive BP monitoring through wearable technology, offering frequent measurements with minimal discomfort. While the study shows promise, further exploration is needed, focusing on optimizing machine learning coefficients for long-term monitoring applications and addressing potential changes over time. Technological improvements, including the implementation of edge computing algorithms, hold the key to enhancing BP accuracy, denoising techniques, and integrating alarm systems for future wearable solutions. This study emphasizes the adaptability of the algorithm for diverse healthcare environments, paving the way for broader applications in convenient and reliable BP monitoring.

In this project, we use a statistical multiple regression to study the impact of eight various predictors (relative compactness, surface area, wall area, roof area, overall height, orientation, glazing area, glazing area distribution) to estimate the cooling load energy efficiency of residential buildings. We try to analyze and visualize the effect of each predictor with each of the response variable using different classical statistical analysis tools used in describing linear models, in such a way so that we can find out the most strongly related predictor variables. Before starting all of this, we use the idea of model selection by stepwise regression technique and compare the AIC of these models and identified a better model between all of them. Then, we compare a classical linear regression approach by simulations on 768 diverse residential buildings show that we can predict CL with low mean absolute error. By using ANOVA we determine variation in the different residuals. Also, we use non constant variance test to verify it. Furthermore, we check leverage and influence points as well as outliers as well as determined cook distance for influential points. By taking box cox transformation and weights, we also introduce WLS technique to fit the model for better results and did all type of important analysis to understand the energy efficiency. Finally, we show 5-fold cross validation to verify our model.

Although data acquisition is a very usual technique, there are several aspects not always considered, as synchronization of acquired measures and evaluation of the errors that derive from this fact. The paper hereby aims to point this thing out, by mathematical determination of the necessary correction and implementing the software meant to evaluate the performances of the acquisition system. As an example, a three-phased acquisition system has been developed in order to monitor the currents and voltages on the three phases. Also other measures have been calculated, such as power and phase. The components on each phase don’t have to be fully identified because a whole system calibration can be made in the first stage. Calibration consists in finding the weighting coefficients for each quantity. The implemented solution for three-phased measures data acquisition starts from the hypothesis of a sampling frequency that respects Shannon theorem. The distance between two samples is small enough to consider a linear evolution between two moments for the same measure. Errors that affect the above mentioned, due to the different moments of time when samples are acquired, are analyzed and brought to the minimum value.

Background: In the functional data analysis (FDA), the hybrid or mixed data are scalar and functional datasets. The semi-functional partial linear regression model (SFPLR) is one of the first semiparametric models for the scalar response with hybrid covariates. Various extensions of this model are explored and summarized. Methods: Two first research articles, including “semi-functional partial linear regression model”, and “Partial functional linear regression” have more than 300 citations in Google Scholar. Finally, only 106 articles remained according to the inclusion and exclusion criteria such as 1) including the published articles in the ISI journals and excluding 2) non-English and 3) preprints, slides, and conference papers. We use the PRISMA standard for systematic review. Results: The articles are categorized into the following main topics: estimation procedures, confidence regions, time series, and panel data, Bayesian, spatial, robust, testing, quantile regression, varying Coefficient Models, Variable Selection, Single-index model, Measurement error, Multiple Functions, Missing values, Rank Method and Others. There are different applications and datasets such as the Tecator dataset, air quality, electricity consumption, and Neuroimaging, among others. Conclusions: SFPLR is one of the most famous regression modeling methods for hybrid data that has a lot of extensions among other models.

Byers Peninsula (62°34’-62°40’S-60°54’61°13’W), 60 km2 in size, is considered one of the largest ice-free areas in Antarctica. Since 2006, the Spanish Polar Program has taken part in a large number of environmental studies involving effects of climate changes, limnology and microbiology, live cycles, but not albedo. Surface albedo is one of the key physical parameters in the surface energy budget of polar regions. Most of Antarctica is covered by ice sheets; only about 0.44% of the area is permanently ice-free. However, in maritime Antarctica, the ice-free areas, corresponding to small islands, peninsulas, and coastal beaches, account for about 3% of the territory. To incorporate the contribution of these areas into global albedo models, it is necessary to relate the soil properties of the ice-free areas to the surface albedo response. Also, mapping soil properties and albedo have and special interest in these ice-free areas. Image classification using machine learning methods trained with georeferenced soil data could be useful for mapping soil properties and albedo in multispectral optical satellite images. A shallow neural network implemented using the Keras Python module was used to define and train models of soil properties using 15 explanatory variables corresponding to bands and spectral indices of a Sentinel image and a population of 49 soil samples taken from the top 5 centimeters of the soil profile. The soil samples were analyzed in the laboratory and a spectral library in the Vis-Nir range (350-2500 nm) was created. The albedo of the samples was integrated from the ADS spectra. At the same time, a linear regression model of albedo using the soil properties as explanatory variables was performed. The R2 fit of this new model was about 0.82 and the error of estimation was 4.1. The model was extended to the entire Byers Peninsula using the ML soil property models as explanatory variables. The RMSE of the extended models increased up to 8.2. We think that the main cause of this increase (2.6 points) is related to the error propagation, phenomenon due to the use of models as explanatory variables. However, another important part of the error increase could be due, among other reasons, to the use of an image that, although corrected, is not completely free of clouds.

Kinetic parameters of SO2 adsorption on unburned carbons from lignite fly ash and activated carbons based on hard coal dust were determined. The model studies were performed using the linear and non-linear regression method for the following models: pseudo first and second-order, intraparticle diffusion, and chemisorption on a heterogeneous surface. The quality of the fitting of a given model to empirical data was assessed based on: R2, R, Δq, SSE, ARE, χ2, HYBRID, MPSD, EABS, and SNE. It was clearly shown that it is the linear regression that more accurately reflects the behaviour of the adsorption system, which is consistent with the first-order kinetic reaction – for activated carbons (SO2+Ar) or chemisorption on a heterogeneous surface – for unburned carbons (SO2+Ar and SO2+Ar+H2O(g)+O2) and activated carbons (SO2+Ar+H2O(g)+O2). Importantly, usually, each of the approaches (linear/non-linear) indicated a different mechanism of the studied phenomenon. A certain universality of the χ2 and HYBRID functions has been proved, the minimization of which repeatedly led to the lowest SNE values for the indicated models. Fitting data by any of the non-linear equations based on the R or R2 functions only, cannot be treated as evidence/prerequisite of the existence of a given adsorption mechanism.

We present a differentially private extension of the block coordinate descent based on objective perturbation. The algorithm iteratively performs linear regression in a federated setting on vertically partitioned data. In addition to a privacy guarantee, the algorithm also offers a utility guarantee; a tolerance parameter indicates how much the differentially private regression may deviate from an analysis without differential privacy. The algorithm’s performance is compared with the standard block coordinate descent algorithm and the trade-off between utility and privacy is studied. The performance is studied using both artificial test data and the forest fires data set. We find that the algorithm is fast and able to generate practical predictions with single-digit privacy budgets, albeit with some accuracy loss.

In order to correct attenuated millimeter-wavelength (Ka-band) radar data and address the problem of instability, an attenuation correction methodology (attenuation correction with variation trend constraint; VTC) was developed. Using synchronous observation conditions and multi-band radars, the VTC method adopts the variation trends of reflectivity in X-band radar data captured with wavelet transform as a constraint to adjust reflectivity factors of millimeter-wavelength radar. The correction was evaluated by comparing reflectivities obtained by millimeter-wavelength cloud radar and X-band weather radar. Experiments showed that attenuation was a major contributory factor in the different reflectivities of the two radars when relatively intense echoes exist, and the attenuation correction developed in this study significantly improved data quality for millimeter-wavelength radar. Reflectivity differences between the two radars were reduced and reflectivity correlations were enhanced. Errors caused by attenuation were eliminated, while variation details in the reflectivity factors were retained. The VTC method is superior to the bin-by-bin method in terms of correction amplitude and can be used for attenuation correction of shorter wavelength radar assisted by longer wavelength radar data.

Soccer is the leading cause of all sports-related ocular injuries in Europe and Israel and leads to blindness at a disproportionately high rate, especially among children (Thompson et al., 2019). With soccer being the most popular sport in the world, it is surprising the only solution to ocular injuries are sports glasses which can cause direct damage to the eye and impair peripheral vision by 15%, calling for an alternative (Smith & Jones, 2020). This work, based on an imported facial model, focuses on both the qualitative and quantitative aspects of building a personalized, low-cost (through optimizing material needed), superior apparatus to conventional sports glasses. The quantitative side examines a modified and model-validated (through a SRS of thirty unique extrapolated points) multivariate linear regression equation, based on horizontal and vertical rotation angles (n=60) trained with residual and computer simulation data, that can accurately extrapolate and quantify ocular impact from all horizontal and vertical rotation angles and a modified Hertzian Contact Stress Equation to determine the thickness of the apparatus using the elasticity modulus, impact force, and geometrical facial and soccer-ball features. The qualitative side examines where firstly, ocular impact is most prevalent, and secondly, where most impact is seen from rotating the ball horizontally and vertically through analysis of Pearson’s Correlation Coefficient at the supraorbital, medial canthus, infraorbital, and lateral canthus regions from both regression equations as well as a cost-benefit analysis for comparison with conventional sports glasses. The findings discovered in this work lay the groundwork for future research to build a customized low-cost ocular injury prevention device which can simultaneously ensure complete ocular safety while enhancing athletic performance for over 250,000,000 players (Johnson & Garcia, 2022).

Ridge regression is one of the most popular shrinkage estimation methods for linear models. Ridge regression effectively estimates regression coefficients in the presence of high-dimensional regressors. Recently, a generalized ridge estimator was suggested by generalizing the uniform shrinkage of ridge regression to the non-uniform shrinkage, which was shown to perform well under sparse and high-dimensional linear models. In this paper, we introduce our newly developed R package “g.ridge” (the first version published on 2023-12-07 at https://cran.r-project.org/package=g.ridge) that implements both the ridge estimator and generalized ridge estimators. The package equips with the generalized cross-validation for automatic estimation of shrinkage parameters. The package also includes a convenient tool for generating a design matrix. By simulations, we test the performance of the R package under sparse and high-dimensional settings with the normal and skew-normal error distributions. From the simulation results, we conclude that the generalized ridge estimator is superior to the benchmark ridge estimator based on “glmnet”, and hence, it can be the most recommended estimator under sparse and high-dimensional models. We demonstrate the package using the intracerebral hemorrhage data.

Byers Peninsula is considered one of the largest ice-free areas in Maritime Antarctica. Since 2006, the Spanish Polar Program has taken part in a large number of environmental studies involving effects of climate changes in lives cycles, limnology and microbiology. Soils from maritime Antarctica are generally weakly developed and have chemical, physical and morphological characteristics strongly influenced by the parent material. However, biological activity during the short Antarctic summer promotes intense transference of nutrients and organic matter in areas occupied by different species of birds and marine mammals. To mapping and monitoring those areas with high biological occupation, could be very useful to have models of edaphic properties prepared from satellite images. In this approach, Deep Learning and Linear Regression models of soil properties and spectral indexes as explicative variables were performed. We training models of soil properties closely related to biological activity such as Dissolved Organic Carbon (DOC) and the iron fraction associated with organic matter (Fe). We tested the best approach to model the spatial distribution of DOC, Fe and pH by training models of Linear Regression and Deep Learning over Sentinel2 and WorldView2 images. The most robust models were used to track possible areas with ornithogenic soils as well as areas of the Byers Peninsula that could support the highest biological development.

Cervical cancer is one of the ailments that endangers the health of women all over the world and causes infertility. Fortunately, this disease can be avoided. Both the results and participation rates of the current preventative strategy remain poor. Hence, preventative or early detection methods remain challenging and open. In gynecology and computer science fields, few studies on identifying cervical cancer are based on behavior risk factor and machine learning. Moreover, various social and behavioral aspects might often make it more difficult to detect cervical cancer especially in low‑ and middle‑income countries (LMICs). Accordingly, focus on predicting the presence of cervical cancer through behavioral risk factors is the basic structure of this research. We proposed an approach to classify cervical cancer from a social-behavioral perspective using logistic regression to predict cervical cancer. We got significantly improved outcomes than the existing methods. Moreover, we used feature engineering to formulate less dimensionality as a pre-processing step and optimized parameters to be prepared for classification phase. The results proved that using the logistic regression with regularization type L1 had a promising performance. The accuracy of Logistic Regression (LR) L1 was 97.2%. Such results support the proposed work as a reliable classification predictive tool.

Climate simulations in West Africa have been attributed with large uncertainties. Global climate projections are not consistent with changes in observations at the regional or local level of the Niger basin, making management of hydrological projects in the basin uncertain. This study evaluates the potential of using the quantile mapping bias correction to improve the Coupled Model Intercomparison Project (CMIP5) outputs for use in hydrology impact studies. Rainfall and temperature projections from 8 CMIP5 Global Climate Models (GCM) were bias corrected using the quantile mapping approach. Impacts of climate change was evaluated with bias corrected rainfall, temperature and potential evapotranspiration (PET). The IHACRES hydrological model was adapted to the Niger basin and used to simulate impacts of climate change on discharge under present and future conditions. Bias correction significantly improved the accuracy of rainfall and temperature simulations compared to observations. Nash coefficient (NSE) for monthly rainfall comparisons of 8 GCMs to the observed was improved by bias correction from 0.69 to 0.84. The standard deviations among the 8 GCM rainfall data were significantly reduced from 0.13 to 0.03. Increasing rainfall, temperature, PET and river discharge were projected for all GCMs used in this study under the RCP8.5 scenario. These results will help improving projections and contribute to the development of sustainable climate change adaptation strategies.

Spatial interpolation of meteorological data can have immense implications on risk management and climate change planning. Kriging with external drift (KED) is a spatial interpolation variant that uses auxiliary information in the estimation of target variable at unobserved locations. However, the traditional KED methods with linear trend functions may not be able to capture the complex and non-linear interdependence between target and auxiliary variables, which can lead to an inaccurate estimation. In this work, a novel KED method using least squares support vector regression (LSSVR) is proposed. This machine learning algorithm is employed to construct trend functions regardless of the type of variable interrelations being considered. To evaluate the efficiency of the proposed method (KED with LSSVR) relative to the traditional method (KED with a linear trend function), a systematic simulation study for estimating the monthly means temperature and pressure in Thailand in 2017 was conducted. The KED with LSSVR is shown to have superior performance over the KED with the linear trend function.

A self-protective metal/ liquid microcapsule composite plating coating has been prepared in our previous research. The release speed of liquid core material from microcapsules is crucial for the coating surface properties. The aim of this paper is to study the permeability rule of liquid microcapsules within composite coatings. According to permeability experimental data’s linear characteristics, multiple linear regression is firstly used to set up permeability model of liquid microcapsules. The results show that a reliable mathematical model about membrane porosity, viscosity of core material and membrane thickness is established under ambient temperature and moisture. Meanwhile, the predictive capacity and reliability of this model are analyzed carefully.

As argued by ‘Declaration of Concrete Environment (2010)’ of Korea and ‘Declaration of Asian Concrete Environment (2011)’ of six Asian countries, concrete as a single material has lately shown extremely large impact on environmental issues such as climate change. Assessment of environmental impact from concrete material and production has considerable importance. Concrete is a major material used in the construction industry that emits a large amount of substances with environmental impacts during its life cycle. Accordingly, technologies for the reduction in and assessment of the environmental impact of concrete from the perspective of Life Cycle Assessment must be developed. At present, the studies in relation to greenhouse gas emission from concrete are being carried out globally as a countermeasure against climate change. In this study, a sustainable concrete mix design algorithm was designed using correlation analyses, and its carbon emission and cost reduction performances were assessed. Using correlation analyses, the concrete strength, w/b and s/a ratios, and CO₂ emissions were identified as major variables of concrete mix design that influenced other variables. Also, this study aims to evaluate the CO₂ emission reduction performance of the algorithm-deduced sustainable concrete mix design, and therefore, the CO₂ emissions of the sustainable concrete mix design are compared with those of the actual concrete mix design applied to the construction of the office building A in South Korea.

Natural polluted insulator surfaces are always coated with various kinds of soluble constituents, and those constituents affect flashover performance differentially. Currently this fact is not considered either in laboratory experiments or field pollution degree measurements, causing the existing insulation selection method to be deficient. In this paper a systematical research on insulator flashover voltage gradient correction involving types of soluble pollution constituents was presented. Taking typical type glass insulator as the sample, its flashover tests polluted by typical soluble chemicals NaCl, NaNO₃, KNO₃, NH₄NO₃, MgSO₄, Ca(NO₃)₂ and CaSO₄ were carried out. Then the flashover gradient correction was made combining the flashover performance of each soluble constituent, the ESDD contribution of the seven constituents, as well as the saturation performance of CaSO₄. The correction was well verified with the flashover test results of insulator polluted by three types of soluble mixture. Research results indicate that the flashover gradient correction method proposed by this paper performs well in reducing the calculating error. It is recommended to carry out component measurements and flashover gradient correction to better select outdoor insulation configuration.

(1) Background: The prediction of cervical lesions evolution is a challenge for clinicians. The prospective study aimed to determine and compare the predictive accuracy of cytology, HPV genotyping, and p16/Ki67 dual staining alone or in combination with personal risk factors for the prediction of progression, regression or persistence of cervical lesions in human papillomavirus (HPV)-infected patients; (2) Methods: This prospective study included HPV-positive patients with or without cervical lesions that underwent follow-up. Descriptive statistics and sensitivity analysis for individual or combined index tests were used for data analysis; (3) Results: The highest predictive performance for the progression of cervical lesions was achieved by a model that comprised a Pap smear suggestive of high-grade squamous intraepithelial lesion (HSIL), the presence of 16/18 HPV strains, a positive p16/Ki67 dual staining result along with the presence of at least 3 clinical risk factors, which had a sensitivity (Se) of 74.42%, a specificity of 97.92%, an area under the receiver operating curve (AUC) of 0.961, and an accuracy of 90.65%. The prediction of cervical lesions regression or persistence was modest; (4) Conclusions: Multiple testing or new biomarkers should be used to improve HPV-positive patient surveillance, especially for cervical lesion regression or persistence prediction.

Digital Elevation Models (DEMs) are widely used in geographic and environmental studies. In the current work, the fusion of multi-source DEMs is investigated to improve the overall accuracy of public domain DEMs. Multi-scale decomposition is an important analytical method in data fusion. Three multi-scale decomposition methods – the wavelet transform (WT), bidimensional empirical mode decomposition (BEMD) and nonlinear adaptive multi-scale decomposition (N-AMD) - are applied to the 1-arc-second Shuttle Radar Topography Mission Global digital elevation model (SRTM-1 DEM) and the Advanced Land Observing Satellite World 3D – 30 m digital surface model (AW3D30 DSM) in China. Of these, the WT and BEMD are popular image fusion methods. A new approach for DEM fusion is developed using N-AMD (which is originally invented to remove the cycle from sunspots). Subsequently, a window-based rule is proposed for the fusion of corresponding frequency components obtained by these methods. Quantitative results show that N-AMD is more suitable for multi-scale fusion of multi-source DEMs, taking the ice cloud and land elevation satellite (ICESat) global land surface altimetry data as a reference. The vertical accuracy of the fused DEM shows significant improvements of 29.6% and 19.3% in a mountainous region and 27.4% and 15.5% in a low-relief region, compared to the SRTM-1 and AW3D30 respectively. Furthermore, a slope position-based linear regression method is developed to calibrate the fused DEM for different slope position classes, by investigating the distribution of the fused DEM error with topography. The results indicate that the accuracy of the DEM calibrated by this method is improved by 16% and 13.6%, compared to the fused DEM in the mountainous region and low-relief region respectively, proving that it is a practical and simple means of further increasing the accuracy of the fused DEM.

Background: We considered a problem of inference in epidemiology when cumulative exposure is the true dose metric for disease, but investigators are only able to measure its duration on each subject. Methods: We undertook theoretical analysis of the problem in the context of a continuous response caused by cumulative exposure, when duration and intensity of exposure follow log-normal distributions, such that analysis by linear regression is natural. We present a Bayesian method to adjust duration-only analysis to incorporate partial knowledge about the relationship between duration and intensity of exposure and illustrate this method in the context of association of smoking and lung function. Results: We derive equations that (a) describe under what circumstances bias arises when duration of exposure is used as a proxy of cumulative exposure, (b) quantify the degree of such bias and loss of precision, and (c) describe how knowledge about relationship of duration and intensity of exposure can be used to recover an estimate of the effect of cumulative exposure when only duration was observed on every subject. Conclusions: Under our assumptions, when duration and intensity of exposure are either independent or positively correlated, we can be more confident in qualitatively interpreting the direction of effects that arise from use of duration of exposure per se. To make reliable inference about the magnitude of effect of cumulative exposure on the outcome, we can use external information on the relationship between duration and intensity of exposure even if intensity of exposure is not available at the individual level.

Although, promotion of urbanization culture in recent decades has made inevitable development of cities in the world, however, the development can be guided in a direction that leave, to the extent possible, minimum socioeconomic and environmental impacts. For this, it is required to first forecast auto-spreading orientation of cities and suburbs in rural areas over time and then avoid shapeless growth of cities. This paper is an attempt to develop a dynamic hybrid model based on logistic regression (LR), Markov chain (MC), and cellular automata (CA) for prediction of future urban sprawl in fast-growing cities. The model was developed using 12 widely-used urban development criteria, whose significant coefficient was determined by logistic regression, and validated by relative operating characteristic (ROC) analysis. The validated model was run in Guilan, a tourist province in northern Iran with a very high rate of urban development. For this, changes in the area of urban land use were detected over the period of 1989 to 2013 and then, future sprawl of the province was forecasted by the years 2025 and 2037. The analysis results revealed that the area of urban land use was increased by more than 1.7 % from 36012.5 ha in 1989 to 59754.8 ha in 2013, and the area of Caspian Hyrcanian forestland was reduced by 31628 ha. The results also predicted an alarming increase in the rate of urban development in the province by the years 2025 and 2037, during which urban land use is predicted to develop 0.9 % and 1.38 %, respectively. The development pattern is expected to be uneven and scattered, without following any particular direction. The development will occur close to the existing or newly-formed urban basements as well as around major roads and commercial areas. This development, if not controlled, will lead to the loss of 13863 ha of Hyrcanian forests and if the trend continues, 21013 ha of Hyrcanian forests and 20208 ha of Barren/open lands are expected to be destroyed by the year 2037. In general, the proposed model is an efficient tool for the support of urban planning decisions and facilitates the process of sustainable development of cities by providing decision-makers with an overview on future development of cities where the growth rate is very fast.

The precipitation, flocculation, and deposition of asphaltene cause severe formation damage within a reservoir and shorten a well’s productive life. Pressure depletion is one factor that contributes to asphaltene precipitation during production; therefore, the first step in managing asphaltene is to determine the onset pressure of the precipitation. While there are numerous equation of state models that can be used to predict the onset pressure, these models are complex and heavily reliant on tuning parameters. Using multivariate linear regression, this work attempts to develop a simple and accurate thermodynamic model for predicting the upper precipitation onset pressure under pressure depletion above the bubble point pressure (Pb) at various temperatures. A total of 94 experimental data points from 37 published crude oil data sets were compiled from the literature. To develop the model, 59 experimental data points were used as training data and 35 experimental data points as testing data. According to the results of the multicollinearity test, the bubble point pressure, temperature, resins, and saturate-to-aromatic ratio were chosen as predictors. The upper onset pressure data with comparable trends were clustered, and unsupervised recognition of three distinct cluster groups was performed. For each cluster identified, a multivariate linear regression model was developed. The model was chosen based on Mallow’s coefficient of determination (Cp), adjusted R² (statistical measure of fit), and S (standard error of the regression slope). The developed model was tested using a data set, and the results showed an adjusted R² of 96.25%, with a mean absolute error of 4.1%. The model was randomly applied to 15 data points to compare it to perturbed-chain statistical associated fluid theory (PC SAFT) and the Peng-Robinson equation of state models and to the multivariate regression models of Fahim (2007) and Ameli et al. (2016). The results showed that the mean absolute error for predicting the asphaltene precipitation onset pressure was 2.82% using Peng-Robinson, 2.36% using the PC SAFT equation of state, 23.96% using the Fahim model, 24.80% using the model reported by Ameli et al., and 2.39% using the newly developed multivariate regression model. The developed multivariate model appears to be as accurate as the PC SAFT equation of state modeling with tuning parameters. The primary advantage of multivariate regression is that, unlike the PC SAFT equation of state model, it does not require saturates, aromatics, resins, and asphaltenes (SARA)-based characterization methodologies or rigorous parameter tuning. It is simple to use, quick, and it produces results in a short period of time.

Notion of median in one dimension is a foundational element in nonparametric statistics. It has been extended to multi-dimensional cases both in location and in regression via notions of data depth. Regression depth (RD) and projection regression depth (PRD) represent the two most promising notions in regression. Carrizosa depth DC is another depth notion in regression. Depth induced regression medians (maximum depth estimators) serve as robust alternatives to the classical least squares estimator. The uniqueness of regression medians is indispensable in the discussion of their properties and the asymptotics (consistency and limiting distribution) of sample regression medians. Are the regression medians induced from RD, PRD, and DC unique? Answering this question is the main goal of this article. It is found that only the regression median induced from PRD possesses the desired uniqueness property. The conventional remedy measure for non-uniqueness, taking average of all medians, might yield an estimator that no longer possesses the maximum depth in both RD and DC cases. These and other findings indicate that the PRD and its induced median are highly favorable among their leading competitors.

The purpose of this study is to show an automated laser vision correction (LVC) with the transep-ithelial refractive keratectomy (TransPRK) surgery technique. Since more surgical steps have been automated over the years, we have standardized the TransPRK technique. We have been using it since 2010. This paper aims to illustrate the processes that are readily applicable to automation. To meet the patient's expectations and ensure that the patient has uncorrected visual acuity at least equal to the preoperative corrected vision with glasses, patient selection is crucial in refractive surgical procedures. One major benefit of automating the surgery is that it can be performed in a similar way by each surgeon or laser correction centre, so once the standard and results are good, these can be per-formed by different surgeons.

This paper presents a two-stage ADC based on pseudo-differential operational transconductance amplifier (OTA), which is designed for the readout circuit of X-ray linear array sensor. This hybrid ADC employs an incremental sigma-delta ADC and a cyclic ADC, achieving a good trade-off between accuracy and conversion speed. The two stages share the same hardware to reduce power consumption and die area. A common-mood feedback module is used to suppress the influence of charge injection, and the effectiveness is demonstrated by detailed theoretical analysis. A test chip of 14-bit ADC is fabricated in 0.35μm CMOS technology. The measured root mean square (RMS) value of DNL is 0.254 LSB, and the maximum value of INL is -0.776/+1.56 LSB. The measured effective number of bits (ENOB) is 13.43 bits.

Atmospheric correction is the processes of converting radiance measured at a spectral 1 sensor to the reflectance of the materials in a multispectral or hyperspectral image. This is an 2 important step for detecting or identifying the materials present in the pixel spectra. We present 3 two machine learning models for atmospheric correction trained and tested on 100,000 batches of 40 4 reflectance spectra converted to radiance using MODTRAN, so the machine learning model learns 5 the radiative transfer physics from MODTRAN. We created a theoretically interpretable Bayesian 6 Gaussian process model and a deep learning autoencoder treating the atmosphere as noise. We 7 compare both methods for estimating gain in the correction model to the well-know QUAC method 8 of assuming a constant mean endmember reflectance. Prediction of reflectance using the Gaussian 9 process model outperforms the other methods in terms of both accuracy and reliability.

There are many uncertainties and risks in residential electricity consumption during the economic development. Knowledge of the relationship between residential electricity consumption and its key determinant—income—are important to the sustainable development of electric power industry. Using panel data from 30 provinces for the 1995-2012 period, this study investigates how residential electricity consumption changes as incomes increase in China. Previous studies typically used linear or quadratic double-logarithmic models imposing ex ante restrictions on the indistinct relationship between residential electricity consumption and income. Contrary to those models, we employed a reduced piecewise linear model that is self-adaptive and highly flexible and circumvents the problem of “prior restrictions.” Robust tests of different segment specifications and regression methods are performed to ensure the conservatism of the research. The results provide strong evidence that the income elasticity was approximately one, and it remained stable throughout the estimation period. The income threshold at which residential electricity consumption automatically remains stable or slows has not been reached. To ensure the sustainable development of the electric power industry, introducing higher energy efficiency standards for electrical appliances and improving income levels are vital. And government should emphasize electricity conservation in industrial sector rather than in residential sector.

In this work we looked for a stable and accurate procedure to perform feature selection in datasets with a much higher number of predictors than individuals, as in Genome-Wide Association Studies. Due to the instability in feature selection when many potential predictors are measured, a variable selection procedure is proposed that combines several replications of shrinkage regression models. A weighted formulation is used to define the final predictors. The procedure is applied to investigate Single Nucleotide Polymorphisms (SNPs) predictors associated to Alzheimer’s disease in the Alzheimer’s disease Neuroimaging Initiative (ADNI) dataset. Two data scenarios are investigated: one considering only the set of SNPs and another with the covariates age, sex, educational level and APOE4 genotype. The SNP rs2075650 and the APOE4 genotype are given as risk factors for AD, which is in line with the literature, and other four new SNPs are pointed, opening new hypotheses for in vivo analyses. These experiments demonstrate the potential of the new method for stable feature selection.

We suppose that a Cooper pair (CP) will experience a damping force exerted by the condensed matter. A Langevin equation of a CP in two dimensional condensed matter is established. Following a method similar to Nelson's stochastic mechanics, generalized Schr\"{o}dinger equation of a CP in condensed matter is derived. If the CPs move with a constant velocity, then the corresponding direct current (DC) electrical conductivity can be calculated. Therefore, a Drude like formula of resistivity of CPs is derived. We suppose that the damping coefficient of CPs in two dimensional cuprate superconductors is a linear function of temperature. Then the resistivity and scattering rate of CPs turn out to be also linear-in-temperature. The origin of linear-in-temperature resistivity and Planckian dissipation in cuprate superconductors may be the linear temperature dependence of the damping coefficient of CPs.

Crop yield estimation supported by satellite remote sensing data can provide expeditious and strategic information for farmers’ decision-making. Most recent forecasting methods have indicated a promising pathway based on machine learning algorithms. However, validation performances, demand for big data and their inherent inexplicability have not yet consolidated a substantial differential to replace methods based on simpler and more understandable models. This paper proposes an approach based on simple linear models fitted from vegetation indices (VIs) assessed at regular intervals of time series derived from MODIS satellite images, aiming to forecast cotton yields in representative areas of the Brazilian Cerrado. Data from 281 commercial production plots were taken to train (167 plots) and test (114 plots) linear regression models relating seed cotton yield and nine well-known VIs averaged in 15-days intervals. Among the evaluated VIs, EVI (Enhanced Vegetation Index) and TVI (Triangular Vegetation Index) showed the lowest root mean square errors (RMSE) and the highest determination coefficients. The best periods for in-season yield prediction were from the 90-105 to 135-150 days after sowing (DAS), i.e. phenological phases corresponding to boll development, open boll and fiber maturation, with lowest RMSE of about 750 kg ha-1 and R2=0.70. The best forecasts for early crop stages were provided by models at the peaks (maximum value of the VI time-series) for EVI and TVI, which occurred around 80-90 DAS. The proposed approach makes the yield predictability more inferable along the crop time series just by providing sowing dates, contour maps and its respective VIs.

In this paper, we compile the fractional power series method and the Laplace transform to design a new algorithm for solving the fractional Volterra integro-differential equation. For that, we assume the Laplace power series (LPS) solution in terms of power q=1m,m∈Z+, where the fractional derivative of order α=qγ for which γ∈Z+. This assumption will help us to write the integral, the kernel, and the nonhomogeneous terms as a LPS with the same power. The recurrence relations for finding the series coefficients can be constructed using this form. To demonstrate the algorithm's accuracy, the residual error is defined and calculated for several values of the fractional derivative. Two strongly nonlinear examples are discussed to provide the efficiency of the algorithm. The algorithm gains powerful results for this kind of problem. Under Caputo meaning the obtained results are illustrated numerically, and graphically. Geometrically, the behavior of the solution declares that the changing of the fractional derivative parameter values' in their domain alters the style of the attained solution in a symmetrical meaning and fully coinciding to the ordinary derivative value'. From these simulations, the results report that the recommended novel algorithm is a straightforward, accurate, and superb tool to generate analytic-approximate solutions for Integral, and integro-differental equations of fractional order.

Objective: To evaluate the variables influencing the length of stay (LoS) for COVID-19 ICU patients at Tygerberg Hospital (Cape Town) and to identify the covariates that significantly influenced it and any potential risk factors associated with LoS. Methods and Results: Poisson, negative binomial (NB), Hurdle–Poisson, and Hurdle–NB regression models were used to model the LoS in this prospective cohort study. The fitted models were compared using the Akaike information criterion (AIC), Vuong’s test criteria, and Rootograms. Based on the chosen performance criteria, the NB model provided the best fit outperforming other candidate models. The baseline LoS count was 8 days. On average, antibiotics reduced LoS by 0.74-fold (95% CI 0.62-0.89) compared to not taking antibiotics. The second wave had a significant effect on the average LoS, which decreased by 0.36-fold (95% CI 0.14-0.93) compared to the first wave. Average LoS increased by 1.01-fold (95% CI 1.01-1.02) for every one-year increase in the age of the patient and by 1.02-fold (95% CI 1.01-1.03) for every 1 unit increase in neutrophils. A 1 ng/L increase in log (TropT) levels decreased the average LoS by 0.87-fold (95% CI 0.81-0.93) similarly, a unit increase in the PF ratio decreased the average LoS by 0.998-fold (95% CI 0.997-0.999) respectively. Conclusion: The study identified common clinical characteristics associated with length of stay in ICU for COVID-19 patients, including age at admission, PF ratio, neutrophils, TropT, Wave, and antibiotic use. These results can aid in identifying risk factors for increased length of stay, assist in healthcare systems planning, and aid in evaluating different models for analysing this type of data.

Fresnel incoherent correlation holography (FINCH) is a well-established incoherent imaging technique. In FINCH, three self-interference holograms are recorded with calculated phase differences between the two interfering, differently modulated object waves and projected into a complex hologram. The object is reconstructed without the twin image and bias terms by a numerical Fresnel back propagation of the complex hologram. A modified approach to implement FINCH by a single camera shot by pre-calibrating the system involving recording of the point spread function library and reconstruction by a non-linear cross-correlation has been introduced recently. The expression of the imaging characteristics from the modulation functions in original FINCH and the modified approach by pre-calibration in spatial and polarization multiplexing schemes are reviewed. The study reveals that a reconstructing function completely independent of the function of the phase mask is required for the faithful expression of the characteristics of the modulating function in the image reconstruction. In polarization multiplexing method by cross-correlation, a partial expression was observed, while in spatial multiplexing method by cross-correlation, the imaging characteristics converged towards a uniform behavior.

For a nonzero normed linear space X‎, ‎we will define some different classes of fuzzy norms on X generated by linear and bounded linear functionals‎. ‎Also separate continuity of the elements of each class are investigated‎. ‎The aim of this research is to introduce a source of examples and counterexamples in the field of fuzzy normed spaces‎.

Observed ENSO statistics exhibits a non-gaussian behavior, which is indicative of the presence of nonlinear processes. In this paper we use the Recharge Oscillator model (ROM), a largely used Low-Order Model (LOM) of ENSO, as well as methodologies borrowed from the field of statistical mechanics to identify which aspects of the system may give rise to nonlinearities that are consistent with the observed ENSO statistics. In particular, we are interested in understanding whether the nonlinearities reside in the system dynamics or in the fast atmospheric forcing. Our results indicate that one important dynamical nonlinearity often introduced in the ROM cannot justify a non-gaussian system behavior, while the nonlinearity in the atmospheric forcing can instead produce a statistics similar to the observed. The implications of the non-Gaussian character of ENSO statistics for the frequency of extreme El Nino events is then examined.

We describe quantum correction to the accreting hot plasma onto black holes. The accreting black holes are surrounded by the very hot ionized plasma. This plasma is heated inevitably by the outgoing photons of the quantum Hawking radiation. It is demonstrated that Hawking radiation prevails over the Compton scattering of hot electrons in the accreting flow onto the small enough evaporating black holes.

In this paper, we study the relativistic correction to Bekenstein-Hawking entropy in the canonical ensemble and isothermal-isobaric ensemble and apply it to the cases of non-rotating BTZ and AdS-Schwarzschild black holes. This is realized by generalizing the equations obtained using Boltzmann-Gibbs(BG) statistics with its relativistic generalization, Kaniadakis statistics, or κ-statistics. The relativistic corrections are found to be logarithmic in nature and it is observed that their effect becomes appreciable only in the high-temperature limit suggesting that the entropy corrections must include these relativistically corrected terms while taking the aforementioned limit. The non-relativistic corrections are recovered in the κ → 0 limit.

For a long time, physicists always directly use mathematical tools to deal with physical problems, and few people pay attention to the difference between mathematical theory and physical theory. Just like the dilemma that physicists once faced when dealing with the problem of blackbody radiation function.By analyzing the difference between the theoretical basis of mathematics and the theoretical basis of physics, this paper draws the following conclusions: (1) The theoretical basis of mathematics and the theoretical basis of physics are different, so when we use mathematical tools for physics research, we need to be very careful. (2) Finiteness and discreteness should be the basis of the whole physical theory; This paper points out that it is not advisable to use infinite " " and infinitesimal "0" without restriction and demonstration in physics, as well as the continuity of functions, which will bring a lot of trouble to physical theory.At the same time, through the analysis of Banach-Tarski paradox and Bertrand paradox, this paper proposes that if we revise the basic assumptions of probability theory: assuming that "points" have quantized sizes, and "lines" also have quantized widths. After the correction, we can not only avoid the troubles caused by Bertrand paradox, but also make probability theory better for practical application.

COVID-19 is the most severe health crisis of the 21st century. COVID-19 presents a threat to almost all countries world-wide. The restriction of human mobility is one of the strategies used to control the transmission of COVID-19. However, it has yet to be determined how effective this restriction is in controlling the rise in COVID-19 cases, particularly in major capital cities such as Jakarta, Indonesia. Using Facebook's mobility data, our study explores the impact of restricting human mobility on COVID-19 case control in Jakarta. Our main contribution is showing how the restriction of human mobility data can give important information about how COVID-19 spreads in different places. We proposed modifying a global regression model into a local regression model by accounting for the spatial and temporal interdependence of COVID-19 transmission across space and time. We applied Bayesian hierarchical Poisson spatiotemporal models with spatially varying regression coefficients. We estimated the regression parameters using an Integrated Nested Laplace Approximation. We found that the local regression model with spatially varying regression coefficients outperforms the global regression model based on DIC, WAIC, MPL, and R2 criteria for model selection. In Jakarta's 44 districts, the impact of human mobility varies significantly. The impacts of human mobility on the log relative risk of COVID-19 range from –4.445 to 2.353. The prevention strategy involving the restriction of human mobility may be beneficial in some districts but ineffective in others. Therefore, a cost-effective strategy had to be adopted.

Linear-width is a well-regarded width parameter in graph theory. The constructs of linear loose tangle and linear tangle present obstacles to attaining linear-width. In this succinct paper, our primary focus will be the exploration of maximal linear loose tangles.

Caudal regression syndrome (CRS) is a congenital abnormality characterized by an incomplete development of the spinal cord (SC) and other abnormalities. We studied a 9-months old CRS child presenting: interruption of SC at L2-L3 level, sacral agenesis, lack of innervation of the inferior limbs (flaccid paraplegia) and neurogenic bladder and bowel. Given the effects of growth hormone (GH) on the proliferation, differentiation and migration of neural stem cells (NSCs), we treated him with GH and rehabilitation, trying to induce the recovery of main sequelae. GMFM-88 test score was 12.31%. After a blood analysis, GH treatment (0.3 mg/day, 5 days/week, 3 months and then 15 days without GH) and rehabilitation commenced. This protocol was followed during 5 years, being the last GH dose 1 mg/day. Blood analysis and physical exams were performed every 3 months initially and every 6 months later. Six months after commencing the treatment GMFM-88 score increased to 39.48%. Responses to sensitive stimuli appeared in most of the territories explored; 18 months later sensitive innervation was complete and the patient moved any muscle over the knees and controlled his sphincters. Three years later he walked with the help of canes, there was plantar flexion and GMFM-88 score was 78.48%. In summary, GH plus rehabilitation may be useful for innervating distal territories, below the level of the incomplete spinal cord in CRS. Most likely, GH acts on ependymal SC NSCs, as the hormone does in the neurogenic niches in the brain.

A description of the motion in Non-Inertial Reference Frames by means of the inclusion of high time derivatives is studied. It is noted that incompleteness of the description of physical reality is a problem of any theory: both quantum mechanics and classical physics. The "stability principle" is put forward. We also provide macroscopic examples of Non-Inertial Mechanics and verify the use of high-order derivatives as non-local hidden variables based the equivalence principle when acceleration is equal to the gravitational field. Acceleration in this case is a function of the higher derivatives with respect to time. The definition of Dark Metrics for matter and energy is presented to replace the standard notions of Dark Matter and Dark Energy.

Atmospheric correction is a necessary step in image processing data and spectra recorded by spaceborne sensors for pure cloudless atmosphere, primarily in the visible and near-IR spectral range. We have present a fast and sufficiently accurate method of atmospheric correction based on the proposed analytical solutions describing with high accuracy the spectrum of outgoing radiation at the top boundary of the cloudless atmosphere. This technique includes the model of the atmosphere and its optical parameters that are important in terms of radiation transfer. The solution of the inverse problem for finding unknown parameters of the model is carried out by the method of non-linear least squares (Levenberg-Marquardt algorithm) for an individual selected pixel of the image (its spectrum), taking into account the adjacency effects. Using the found parameters of the atmosphere and the average surface albedo, assuming homogeneity of the atmosphere within a certain area of the hyperspectral image (or the whole frame), the spectral albedo at the Earth's surface is calculated for all other pixels. It is essential that the procedure of the numerical simulation with non-linear least squares of the direct transfer problem is based on using analytical solutions, which provides a very short calculation time of the atmospheric parameters (seconds or less) and the ability to perform atmospheric correction "on-fly." Testing methods of atmospheric correction was performed using the synthetic outgoing radiation spectra at the top of the atmosphere (TOA), obtained by numerical simulation in the LibRadTran code, as well as spectra of real space images of the Hyperion hyperspectrometer. A comparison with the results of atmospheric correction in module FLAASH of ENVI package has been performed. Finally, to validate our data obtained by the SHARK method, a comparative analysis with ground-based measurements of Radiometric Calibration Network (RadCalNet) was carried out.

In Taiwan, mountainous areas account for approximately two-thirds of the total area. The steep terrain and concentrated rainfall during typhoons cause landslides, which pose a considerable threat to mountain settlements. Therefore, models for analyzing rainfall-induced landslide hazards are urgently required to ensure adequate land use in mountainous areas. In this study, focusing on Pingtung County in southern Taiwan, we developed a landslide hazard index (IRL) to land use. Using FORMOSA-2 and SPOT-5 satellite images, data were collected before and after four typhoons (one in 2009 and three in 2013). The ArcGIS random tree classifier was used for interpreting satellite images to explore surface changes and disasters, which were used to analyze slope disturbances. The product of the maximum 3-h rolling rainfall intensity and effective accumulated rainfall was used as a rainfall trigger index (IRT). Considering environmental and slope disturbance factors, an index of slope environmental strength potential (ISESP) was developed through logistic regression (LR). Landslide hazard to land use was estimated using IRT and ISESP. The average coefficient of agreement (Kappa) was approximately 0.71 (medium to high accuracy); the overall accuracy of slope environmental strength potential analysis was approximately 80.4%. At a constant ISESP, IRT increased with the increasing hazard potential of rainfall-induced landslides. Furthermore, IRT and ISESP were positively correlated with landslide occurrence. When large ISESP values occur (e.g., fragile environment and high land development intensity), small IRT values may induce landslides.

As known all physical properties of solids are described well by the system of quantum linear harmonic oscillators. It is shown in the present paper that the system consisting of classical linear harmonic oscillators having temperature dependent masses or (and) frequencies has the same partition function as the system consisting of quantum linear harmonic oscillators having temperature independent masses and frequencies while the means of the square displacements of the positions of the oscillators from their mean positions for the system consisting of classical linear harmonic oscillators having: the temperature dependent masses; temperature dependent frequencies; and temperature dependent masses and frequencies differ from each other and from that of the system consisting of quantum linear harmonic oscillators, and hence, the system consisting of classical linear harmonic oscillators describes well the thermodynamic properties of the system consisting of quantum linear harmonic oscillators and solids.

Expectation maximization (EM) algorithm is a powerful mathematical tool for estimating statistical parameter when data sample contains hidden part and observed part. EM is applied to learn finite mixture model in which the whole distribution of observed variable is average sum of partial distributions. Coverage ratio of every partial distribution is specified by the probability of hidden variable. An application of mixture model is soft clustering in which cluster is modeled by hidden variable whereas each data point can be assigned to more than one cluster and degree of such assignment is represented by the probability of hidden variable. However, such probability in traditional mixture model is simplified as a parameter, which can cause loss of valuable information. Therefore, in this research I propose a so-called conditional mixture model (CMM) in which the probability of hidden variable is modeled as a full probabilistic density function (PDF) that owns individual parameter. CMM aims to extend mixture model. I also propose an application of CMM which is called adaptive regressive model (ARM). Traditional regression model is effective when data sample is scattered equally. If data points are grouped into clusters, regression model tries to learn a unified regression function which goes through all data points. Obviously, such unified function is not effective to evaluate response variable based on grouped data points. The concept “adaptive” of ARM means that ARM solves the ineffectiveness problem by selecting the best cluster of data points firstly and then evaluating response variable within such best cluster. In order words, ARM reduces estimation space of regression model so as to gain high accuracy in calculation.

The article presents a model for optimizing biomass supply chains using the linear programming framework integrated with a Geographic Information System. Based on the distance from a given type of biomass resource, its calorific value, price, and transportation costs, the model identifies the optimal source of biomass, allowing it to cover the demand for the required total energy value with the lowest possible costs. The case study includes the Połaniec power plant in southeastern Poland and potential sources of forest biomass and agricultural straw within 100 km of the plant. Unit costs of biomass varied depending on biomass availability and energy demands. For energy demand on the level of 1 PJ yearly, the lowest unit costs of biomass (4.08 €/MJ) were when all kinds of biomass were available, and the highest (5.47 €/MJ) was when only stacked wood was available. As energy demand increased, unit costs increased, and the ability to meet this demand with just one type of biomass decreased. The energy biomass sector can utilize the model to benefit both biomass producers and their final buyers.

A family of linear singularly perturbed Cauchy problems is studied. The equations defining the problem combine both partial differential operators together with the action of linear fractional transforms. The exotic geometry of the problem in the Borel plane, involving both sectorial regions and strip-like sets, gives rise to asymptotic results relating the analytic solution and the formal one through Gevrey asymptotic expansions. The main results lean on the appearance of domains in the complex plane which remain intimately related to Lambert W function, which turns out to be crucial in the construction of the analytic solutions. On the way, an accurate description of the deformation of the integration paths defining the analytic solutions and the knowledge of Lambert W function are needed in order to provide the asymptotic behavior of the solution near the origin, regarding the perturbation parameter. Such deformation varies depending on the analytic solution considered, which lies in two families with different geometric features.

This work intends to present a study on relations between a Lie algebra called dispersion operators algebra, linear canonical transformation and a phase space representation of quantum mechanics that we have introduced and studied in previous works. The paper begins with a brief recall of our previous works followed by the description of the dispersion operators algebra which is performed in the framework of the phase space representation. Then, linear canonical transformations are introduced and linked with this algebra. A multidimensional generalization of the obtained results is given.

In the paper, the authors present an explicit form for a family of inhomogeneous linear ordinary differential equations, find a more significant expression for all derivatives of a function related to the solution to the family of inhomogeneous linear ordinary differential equations in terms of the Lerch transcendent, establish an explicit formula for computing all derivatives of the solution to the family of inhomogeneous linear ordinary differential equations, acquire the absolute monotonicity, complete monotonicity, the Bernstein function property of several functions related to the solution to the family of inhomogeneous linear ordinary differential equations, discover a diagonal recurrence relation of the Stirling numbers of the first kind, and derive an inequality for bounding the logarithmic function.

Smallsats are becoming the predominant electro-optical Earth observation (EO) imaging platforms. While atmospheric correction of smallsat data enhances its utility, an established pathway to do so may constrain accuracy and utility. The alternative, Closed-form Method for Atmospheric Correction (CMAC), developed for smallsat application provides surface reflectance derived solely from scene statistics. In a prior paper, CMAC closely agreed with Land Surface Reflectance Code (LaSRC) software for correction of the four VNIR bands of Landsat-8/9 images for conditions of low to moderate atmospheric effect over quasi-invariant warehouse-industrial targets. Those results were accepted as surrogate surface reflectance to support analysis of CMAC and LaSRC reliability for surface reflectance retrieval in two contrasting environments: shortgrass prairie and barren desert. Reliability was defined and tested through a null hypothesis: the same top-of-atmosphere reflectance under the same atmospheric condition will provide the same estimate of surface reflectance. Evaluated against the prior surrogate surface reflectance, the results found decreasing error with increasing wavelength for both methods. From 58 comparisons across the four bands, LaSRC average absolute error ranged from 0.59% (NIR) to 50.30% (blue). CMAC error was well constrained from 0.01% (NIR) to 0.98% (blue) sustaining the null hypothesis for reliability.

Tropical cyclones (TC) are dangerous weather events and accurate monitoring and forecasting can provide significant early warning to reduce loss of life and property. However, the study of tropical cyclone intensity remains challenging, both in terms of theory and forecasting. ERA5 reanalysis is benchmark data set for tropical cyclone studies, yet the maximum wind speed error is very large (68 kts) and still 19 kts after simple linear correction even in the better sampled North Atlantic. Here, we develop an adaptive learning approach to correct the intensity in the ERA5 reanalysis, by optimising the inputs to overcome the problems because of the poor data quality and updating the features to improve the generalisability of the deep learning-based model. Specifically, we use TC knowledge to increase the representativeness of the inputs so that the general features can be learned with deep neural networks in the sample space, and then use domain adaptation to update the general features from the known domain with historical storms to the specific features for the unknown domain of new storms. This approach can reduce the error to only 6 kts which is within the uncertainty of the best track data in IBTrACS in the North Atlantic. The method may have wide applicability, such as extending it to the correction of intensity estimation from satellite imagery and intensity prediction from dynamical models.

Two-dimensional mass spectrometry (2D MS) is a method for tandem mass spectrometry that relies on manipulating ion motions to correlate precursor and fragment ion signals. 2D mass spectra are obtained by performing a Fourier transform in both the precursor ion mass-to-charge ratio (m/z) dimension and the fragment ion m/z dimension. The phase of the ion signals evolves linearly in the precursor m/z dimension and quadratically in the fragment m/z dimension. This study demonstrates that phase-corrected absorption mode 2D mass spectrometry improves signal-to-noise ratios by a factor of 2 and resolving power by a factor of 2 in each dimension compared to magnitude mode. Furthermore, phase correction leads to an easier differentiation between ion signals and artefacts, and therefore easier data interpretation.

Gesture-based recognition is one of the most intuitive methods for inputting information and is not subject to cumbersome operations. Recognition is performed on human's consecutive motion without reference to retrial or alternation by user. We propose a gesture recognition model with a mechanism for correcting recognition errors that operates interactively and is practical. We applied the model to a setting involving a manual grading task in order to verify its effectiveness. Our system, named GERMIC, consists of two major modules, namely, handwritten recognition and interactive correction. Recognition is materialized with image feature extraction and convolutional neural network. A mechanism for interactive correction is called on-demand by a user-based trigger. GERMIC monitors, track, and stores information on the user's grading task and generates output based on the recognition information collected. In contrast to conventional grading done manually, GERMIC significantly shortens the total time for completing the task by 24.7% and demonstrates the effectiveness of the model with interactive correction in two real world user environments.

Academic publishing is undergoing a highly transformative process, and many rules and value systems that were in place for years are being challenged in unprecedented forms leading to the evolution of novel ways of dealing with new pressures. One of the most important aspects of an integrated and valid academic literature is the ability to screen publications for errors during peer review to weed out mistakes, fraud and inconsistencies, such that the final published product represents a product that has value, intellectually, and otherwise. It is difficult to claim the existence of perfect manuscripts. The level of errors that exist in a manuscript will depend on the rigor of the research group and of the peer review process that was used to screen that paper. When errors slip into a final published paper, either through honest error or misconduct, and are not detected during peer review and editorial screening, but are spotted during post-publication peer review, an opportunity is created to set the record straight, and to correct it. To date, the most common forms of correcting the literature have been errata, corrigenda, expressions of concern, and retractions. Despite this range of corrective measures, which represent artificially created corrals around pockets of imperfect literature, certain cases do not quite fit this mold, and new suggested measures for correcting the literature have been proposed, including manuscript versioning, amendments, partial retractions and retract and replace. In this commentary, a discussion of the evolving correction of the literature is provided, as are perspectives of the risks and benefits of such new measures to improve it.

Quantum computing has attracted significant interest in the optimization community because it potentially can solve classes of optimization problems faster than conventional supercomputers. Several researchers proposed quantum computing methods, especially Quantum Interior Point Methods (QIPMs), to solve convex optimization problems, such as Linear Optimization, Semidefinite Optimization, and Second-order Cone Optimization problems. Most of them have applied a Quantum Linear System Algorithm at each iteration to compute a Newton step. However, using quantum linear solvers in QIPMs comes with many challenges, such as having ill-conditioned systems and the considerable error of quantum solvers. This paper investigates how one can efficiently use quantum linear solvers in QIPMs. Accordingly, an Inexact Infeasible Quantum Interior Point Method is developed to solve linear optimization problems. We also discuss how we can get an exact solution by Iterative Refinement without excessive time of quantum solvers. Finally, computational results with a QISKIT implementation of our QIPM using quantum simulators are analyzed.

This manuscript presents a new two-parameter unit stochastic distribution, obtained by transforming the Laplace distribution, using generalized logistic map, into a unit interval. The distribution thus obtained is named the Laplace-logistic unit (abbreviated LLU) distribution, and its basic stochastic properties are examined in detail. Also, the procedure for estimating parameters based on quantiles is provided, along with the asymptotic properties of the obtained estimates and the appropriate numerical simulation study. Finally, the application of the LLU distribution in dynamic and regression analysis of real-world data with accentuated "peaks" and "fat" tails is also discussed.

Like traditional single label learning, multi-label learning is also faced with the problem of dimensional disaster.Feature selection is an effective technique for dimensionality reduction and learning efficiency improvement of high-dimensional data. In this paper, Logistic regression, manifold learning and sparse regularization were combined to construct a joint framework for multi-label feature selection (LMFS). Firstly, the sparsity of the eigenweight matrix is constrained by the $L_{2,1}$-norm. Secondly, the feature manifold and label manifold can constrain the feature weight matrix to make it fit the data information and label information better. An iterative updating algorithm is designed and the convergence of the algorithm is proved.Finally, the LMFS algorithm is compared with DRMFS, SCLS and other algorithms on eight classical multi-label data sets. The experimental results show the effectiveness of LMFS algorithm.

Long-term, high-accuracy mapping of built-up land dynamics is essential for understanding urbanization and its consequences for the environment. Despite advances in remote sensing and classification algorithms, built-up land mapping using early satellite imagery (e.g., from the 2000s and earlier) remains prone to uncertainty. We mapped the extent of built-up land in the North China Plain, one of China’s most important agricultural regions, from 1990 to 2019 at three-year intervals. Using dense time-stack Landsat data, we applied discrete Fourier transformation to create temporal predictors and reduce mapping uncertainties for early years. We improved overall accuracy by 8% compared to using spectral and indices predictors alone. We implemented a temporal correction algorithm to remove inconsistent pixel classifications, further improving accuracy to a consistently high level (>94%) across years. A cross-product comparison showed that our study achieved the highest levels of accuracy across years. Total built-up land in the North China Plain increased from 37,941 km² in 1990–1992 to 131,578 km² in 2017–2019. Consistent, high-accuracy built-up land mapping provides a reliable basis for policy planning in one of the most rapidly urbanizing regions of the planet.

We introduce linear probing hashing schemes that construct a hash table of size $n$, with constant load factor $\alpha$, on which the worst-case unsuccessful search time is asymptotically almost surely $O(\log \log n)$. The schemes employ two linear probe sequences to find empty cells for the keys. Matching lower bounds on the maximum cluster size produced by any algorithm that uses two linear probe sequences are obtained as well.

A numerical application of linear-molecule symmetry properties, described by the D_∞h point group, is formulated in terms of lower-order symmetry groups D_nh with finite n. Character tables and irreducible representation transformation matrices are presented for D_nh groups with arbitrary n-values. These groups are subsequently used in the construction of symmetry-adapted ro-vibrational basis functions for solving the Schrödinger equations of linear molecules as part of the variational nuclear motion program TROVE. The TROVE symmetrisation procedure is based on a set of "reduced" vibrational eigenvalue problems with simplified Hamiltonians. The solutions of these eigenvalue problems have now been extended to include the classification of basis-set functions using ℓ, the eigenvalue (in units of ℏ) of the vibrational angular momentum operator ${\widehat{L}}_z$ . This facilitates the symmetry adaptation of the basis set functions in terms of the irreducible representations of D_nh. ¹²C₂H₂ is used as an example of a linear molecule of D_∞h point group symmetry to illustrate the symmetrisation procedure.

High-dimensional measurement error data are becoming more prevalent across various fields. Research on measurement error regression models has gained increasing attention due to the risk of drawing inaccurate conclusions if measurement errors are ignored. When the dimension p is larger than the sample size n, it is challenging to develop statistical inference methods for high-dimensional measurement error regression models due to the existence of bias, nonconvexity of objective function, high computational cost and many other difficulties. Over the past few years, some works have overcome the aforementioned difficulties and proposed several statistical inference methods. This paper mainly reviews the current development on estimation, hypothesis testing and variable screening methods for high-dimensional measurement error regression models and shows the theoretical results of these methods with some directions worthy of exploring for future research.

Predicting copper price is essential for making decisions that can affect companies and governments dependent on the copper mining industry. Copper prices follow a time series that is non-linear, non-stationary, and which have periods that change as a result of potential growth, cyclical fluctuation and errors. Sometimes the trend and cyclical components together are referred to as a trend-cycle. In order to make predictions, it is necessary to consider the different characteristics of trend-cycle. In this paper, we study a copper price prediction method using Support Vector Regression. This work explores the potential of the Support Vector Regression with external recurrences to make predictions at 5, 10, 15, 20 and 30 days into the future in the copper closing price at the London Metal Exchanges. The best model for each forecast interval is performed using a grid search and balanced cross-validation. In experiments on real data-sets, our results obtained indicate that the parameters (C, ε, γ) of the model Support Vector Regression do not differ between the different prediction intervals. Additionally, the amount of preceding values used to make the estimates does not vary according to the predicted interval. Results show that the support vector regression model has a lower prediction error and is more robust. Our results show that the presented model is able to predict copper price volatilities near reality, being the RMSE equal or less than the 2.2% for prediction periods of 5 and 10 days.

Regression models form the core of the discipline of econometrics. One of the basic assumptions of classical linear regression model is that the values of the explanatory variables are fixed in repeated sampling. However, in most of the real life cases, particularly in economics the assumption of fixed regressors is not always tenable. Under a non-experimental or uncontrolled environment, the dependent variable is often under the influence of explanatory variables that are stochastic in nature. There is a huge literature related to stochastic regressors in various aspects. In this paper, a historical perspective on some of the works related to stochastic regressor is being tried to pen down based on literature search.

The development of anti-pain technologies in the complex treatment of pain syndromes is one of the most urgent tasks of modern medicine. We have undertaken a placebo-controlled experimental study of the therapeutic potential of low-intensity laser radiation when applied to acupuncture points, which are directly related to the autonomic nervous system. The adaptation effect of puncture photobiomodulation on the induction of stress-mediated autonomic reactions, oxidative metabolism and microcirculation in animals during the acute phase of pain stress was revealed. The data obtained are of interest for use in the complex rehabilitation of patients with pain syndrome.

An easier method for the calibration of differential drive robots is presented. Most of the calibration is done on-board and it is not necessary to expend too much time taking note of the robot's position. The calibration method does not need a big free space to perform the tests. The bigger space is just in a straight line, which is easy to find. Results with the proposed method are compared with those from UMB as a reference, and they show very little deviation while the proposed calibration is much simpler.

Advances in remote sensing have led to use of satellite-derived rainfall products to complement the sparse rain gauge data. Although globally derived and some regional bias corrected, these products often show large discrepancies with ground measurements attributed to local and external factors that require systematic consideration. Decreasing rain gauge network however inhibits continuous validation of these products. We propose to deal with this problem by the use of Bayesian approach to merge the existing historical rain gauge information to create a consistent satellite rainfall data that can be used for climate studies. Monthly Bayesian bias correction is applied to the Climate Hazards Group Infrared Precipitation with Stations (CHIRPS v2) data to reduce systematic errors using a corresponding gridded (0.05°) rain gauge data over East Africa for a period of 33 (1981–2013) years of which 22 years are utilized to derive error fields which are then applied to an independent CHIRPS data for 11 years for validation. The bias correction is spatially and temporally assessed during the rainfall wet months of March-May (MAM), June-August (JJA) and October–December (OND) in East Africa. Results show significant reduction of systematic errors at both monthly and yearly scales and harmonization of their cumulative distributions. Monthly statistics showed a reduction of RMSD (29–56)% and MAE (28–60)% and an increase of correlations (2–32) %, while yearly ones showed reductions of RMSD (9-23)%, and MAE (7–27)% and increase of correlations (4–77)% for MAM months, reduction of RMSD (15–35)% and MAE (16–41)% and increase in correlations (5–16)% for JJA months, and reduction of RMSD (3–35)% and MAE (9–32)% and increase of correlations (3–65)% for OND months. Systematic errors of corrected data were influenced by local processes especially over Lake Victoria and high elevated areas. Large-scale circulations induced errors were mainly during JJA and OND rainfall seasons and were reduced by the separation of anomalous years during training. The proposed approach is recommended for generating long-term data for climate studies where consistencies of errors can be assumed.

While the simple model of the total atmospheric carbon sink effect as a linear function of concentration has provided excellent prediction results, several problems remained to be investigated and solved. The most obvious open issue is the correct treatment of land use change emssions. It turns out that the model improves by mostly neglecting them after 1959. This effectively implies that land use change emissions have been constant and small since then. The key investigation starts with the observation, that the total carbon sink has a short term component which be explained by temperature changes commonly known as El Nin˜o. The apparent paradox is analysed and explained, why contrary to the short term changes no temperature caused trend can be detected in the model, despite the fact that several contributing processes exhibit temperature dependency. The result of this analysis leads to the model extension, where the total effect of sinks and natural emissions are a linear function of concentration and temperature. This model not only explains current measurements but also paleo climate from ice-core time series.

Oscillons, fundamental to various physical domains, are examined in-depth in this paper. From Josephson junctions in superconducting circuits to classical and quantum field theories, oscillators reveal profound insights into diverse phenomena. The study primarily focuses on oscillons, distinctive field configurations with enduring localization, establishing intriguing connections with well-known models like the Sine-Gordon breather. Surprising parallels in the weak coupling limit illuminate the rich dynamics of oscillators. A semi-classical quantization method, discretizing the field into spatially homogeneous regions, exposes stability angles, providing insights into the quantum nature of oscillons. The application of this quantization framework to specific cases, including the Sine-Gordon breather, showcases its versatility. The results offer a comprehensive perspective on the quantization of oscillons, unraveling the intricate interplay between classical and quantum dynamics. In conclusion, this paper provides a profound exploration of quantum oscillators, unveiling novel connections and presenting a rigorous quantization framework. The gained insights contribute significantly to the broader understanding of oscillatory systems and their pivotal role in diverse physical phenomena.

The core of risk aggregation in the Solvency II Standard Formula is the so-called square root formula. We argue that it should be seen as a means for the aggregation of different risks to an overall risk rather than being associated with variance-covariance based risk analysis. Considering the Solvency II Standard Formula from the viewpoint of linear geometry, we immediately find that it defines a norm and therefore provides a homogeneous and sub-additive tool for risk aggregation. Hence Euler's Principle for the reallocation of risk capital applies and yields explicit formulas for capital allocation in the framework given by the Solvency II Standard Formula. This gives rise to the definition of diversification functions, which we define as monotone, subadditive, and homogeneous functions on a convex cone. Diversification functions constitute a class of models for the study of the aggregation of risk, and diversification. The aggregation of risk measures using a diversification function preserves the respective properties of these risk measures. Examples of diversification functions are given by seminorms, which are monotone on the convex cone of non-negative vectors. Each L^p norm has this property, and any scalar product given by a non-negative positive semidefinite matrix does as well. In particular, the Standard Formula is a diversification function and hence a risk measure that preserves homogeneity, subadditivity, and convexity.

This paper uses the numerical results of surveys sent to Huelva’s (Andalusia, Spain) households to determine the degree of knowledge they have about the urban water cycle, needs, values, and attitudes regarding water in an intermediary city with low water stress. In previous research, we achieved three different households’ clusters. The first one grouped households with high knowledge of the integral water cycle and a positive attitude to smart devices at home. The second cluster described households with low knowledge of the integral water cycle and high sensitivity to price. The third one showed average knowledge and predisposition to have a closer relationship with the water company. This paper continues with this research line, applying Classification and Regression Trees (CART) to determine which hierarchy of variables/factors/ independent components obtained from the surveys are the decisive ones to predict the range of household water consumption in Huelva. Positive attitudes towards improved cleaning habits for personal or household purposes are the highest hierarchy component to predict the water consumption range. Second in the hierarchy, the variable Knowledge Global Score about the integral urban water cycle, associated with water literacy, also contributes to predicting the water consumption range. Together with the three clusters obtained previously, these results will allow us to design water demand management strategies (WDM) fit for purpose that enable Huelva’s households to use water more efficiently.

This work evaluates the surface water quality in terms of physico-chemical parameters of the Brahmani River, Odisha using statistical analysis involving the calculation of correlation coefficient and regression equation. Besides this, the work also highlights and draws attention towards the “Water Quality Index” in a simplified format which may be used at large and could represent the reliable picture of water quality. Surface water quality data is taken from OSPCB of various location i.e. Panposh D/S, Rourkela D/S, Rengali, Talcher U/S, Kamalanga D/S, Bhuban, Pattamundai and was assessed for summer, monsoon, winter for the years 2011, 2012, 2013, 2014 and 2015. Average of values, minimum of values and maximum of values of water quality parameters were obtained seasonally over the above mentioned years. Besides this, the standard deviation for the water quality parameters was also obtained for water quality parameters namely pH, Temperature, DO, TDS, Alkalinity, EC, Na+, Ca2+, Mg2+, K+, F-, Cl-, NO3-, SO42- and PO42-. Seasonal changes in various physical and chemical parameters were analysed.The values obtained were compared with the guideline values for drinking water by Bureau of Indian Standard (BIS). A systematic correlation and regression study is carried out for three seasons, showed linear relationship among different water quality parameters. This provides an easy and rapid method of monitoring water quality. Highly significant (0.8< r <1.0), moderately significant (0.6< r <0.8) and significant (0.5< r <0.6) correlations between the parameters have been worked out. High correlation coefficient has been observed between TDS,EC-Na+, Ca2+, Cl-, SO42- ; Na+- Cl-. From the collected quantities, certain parameters were selected to derive WQI for the variations in water quality of each designated sampling site. WQI of Brahmani River ranged from 36.7 to 44.1 which falls in the range of good quality of water.Panposh D/S and Rourkela D/S showed poor water quality in summer and winter season. It is shown that WQI may be a useful tool for assessing water quality and predicting trend of variation in water quality at differentlocations in the Brahmani River.

There is high prevalence of hypertension and is rapidly increasing around the world, despite the intervention programme implemented, this study aimed at estimating the prevalence rate, test of association between hypertension and risk factors and model hypertension rate. Data used was obtained from the health record of Federal Medical Centre, Keffi from January 2016 – January 2019. Ordinal logistic regression model was used; Model Fitting Information, Goodness-of-Fit, Pseudo R-Square and Test of Parallel Lines are fitted to the data sets to test the accuracy and correctness of the model. The results indicated that the overall prevalence of hypertension rate is high at 36.4%, among the adult population, body mass index and gender are statistically significant, and Age is not significant in the study. Individuals that are overweight are more likely to be hypertensive compare to other weights. At age 40 – 49 years which have the highest rate of 26.5% and the odd ratio is 0.75 compared to others. One year increase in age 30 – 39, the cumulative odd of being hypertensive is 0.91 while other independent variables are held constant. The odd ratio of female being hypertensive is 0.85, therefore the females are more likely to be hypertensive with 54.4% compared to the males at 45.6% . There is no presence of multicolinearity among the variables and Logit models were formulated to calculate probabilities of the various possible outcomes.

Atmospheric propagational phase variations are the dominant source of error for InSAR timeseries analysis, generally exceeding uncertainties from poor SNR or signal correlation. The spatial properties of these errors have been well studied, but their temporal dependence and correction have received much less attention to date. We present here an evaluation of the magnitude of tropospheric artifacts in derived time series after compensation using an algorithm that requires only the InSAR data themselves. The level of artifact reduction equals or exceeds that from many weather model based methods, while avoiding the need to access fine-scale atmosphere parameters globally at all times. Our method consists of identifying all points in an InSAR stack with consistently high correlation, and computing, then removing, a fit of the phase at each of these points with respect to elevation. Comparison with GPS truth yields a reduction of 3, from an rms misfit of 5-6 cm to ~2 cm over time. This algorithm can be readily incorporated into InSAR processing flows without need for outside information.

Since the discovery of the first reported case with Zinc-deficiency in Iran¹ by Prasad et al. in 1961, the knowledge on Zinc has increased significantly. Zinc is the second most abundant common trace mineral in the human body, responsible for vital biological functions from cell growth and development to cell homeostasis and immune response ^2,3. Up to a fifth of the global population is estimated to suffer from different degrees of Zinc deficiency⁴. In the western world, Zinc deficiency is more prevalent among the geriatric population³, vegans/vegetarians, and people with certain underlying conditions⁴such as liver cirrhosis, inflammatory bowel disease, and various auto-immune disorders^4,5. Zinc and Zinc deficiency has been associated with several infectious diseases ^2,3. Severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) which is responsible for the ongoing pandemic belongs to the family of coronaviruses. SARS-CoV-2 has a high genetic similarity to another family member, SARS-CoV, which caused the first major epidemic of the 21^st century^6,7. Currently, there is no evidence linking the anti- SARS-CoV-2 response and the element Zinc. Herein and in light of the SARS-CoV-2 pandemic, we marshal the evidence associating the element Zinc with the anti-viral and antibacterial immune response as well as the cytokine storm and lung injury. Such a revisit of the precedent evidence may inspire further investigation assessing the relationship between Zincemia status and the anti-viral response in SARS-CoV-2 patients.

Document deskewing is a fundamental problem in document image processing. While existing methods have limitations, such as Hough Line Transformation that can deskew images upside down, and Deep Learning models that require huge amounts of human labour and computational resources and still fail to deskew while taking care of orientation, OCR-based methods also struggle to read text when it is tilted. In this paper, we propose a novel, simple, cost-effective deep learning method for fixing the skew and orientation of documents. Our approach reduces the search space for the machine learning model to predict whether an image is upside down or not, avoiding the huge search space of predicting an angle between 0 and 360. We finetuned a MobileNetV2 model, which was pre-trained on imagenet, using only 200 images and achieve good results. This method is useful for automation-based tasks, such as data extraction using OCR technology, and can greatly reduce manual labour.

We present a new penalized method for estimation in sparse logistic regression models with group structure. Group sparsity suggests us to consider the Group Lasso penalty. Being different from penalized log-likelihood estimation, our method can be viewed as a penalized weighted score function method. Under some mild conditions, we provide non-asymptotic oracle inequalities promoting group sparsity of predictors. A modified block coordinate descent algorithm based on a weighted score function is also employed. The net advantage of our algorithm over the existing Group Lasso-type procedures is that the tuning parameter can be pre-specified. The simulations show that this algorithm is considerably faster and more stable than competing methods. Finally, we illustrate our methodology with two real data sets.

Computational Fluid Dynamics (CFD)-based simulation has been the traditional way to model complex industrial systems and processes. One very large and complex industrial system that has benefited from CFD-based simulations is the steel blast furnace. The problem with the CFD-based simulation approach is that it tends to be very slow to generate data. The CFD-only approach may not be fast enough for use in real-time decision-making. To address this issue, in this work, the authors propose the use of machine learning techniques to train and test models based on data generated via CFD simulation. Regression models based on neural networks are compared to tree boosting models. In particular, several areas (tuyere, raceway, and shaft) of the blast furnace are modeled using these approaches. The results of the model training and testing are presented and discussed. The obtained R2 metrics are, in general, very high. The results look promising and may help to improve the efficiency of operator and process engineer decision-making when running a blast furnace.

Training supervised machine learning models requires labeled examples. A judicious choice of examples is helpful when there is a significant cost associated with assigning labels. This article improves upon a promising extant method – Batch-mode Expected Model Change Maximization (B-EMCM) method – for selecting examples to be labeled for regression problems. Specifically, it develops and evaluates alternate strategies for adaptively selecting batch size in B-EMCM. By determining the cumulative error that occurs from the estimation of the stochastic gradient descent, a stop criteria for each iteration of the batch can be specified to ensure that selected candidates are the most beneficial to model learning. This new methodology is compared to B-EMCM via mean absolute error and root mean square error over ten iterations benchmarked against machine learning data sets. Using multiple data sets and metrics across all methods, one variation of AB-EMCM, the max bound of the accumulated error (AB-EMCM Max), showed the best results for an adaptive batch approach. It achieved better root mean squared error (RMSE) and mean absolute error (MAE) than the other adaptive and non-adaptive batch methods while reaching the result in nearly the same number of iterations as the non-adaptive batch methods.

Neither tumor growth nor regression is truly spontaneous, but both may under special circumstances be driven by similar events. We describe a sequence of processes that typically leads to tumor progression but may on occasion inadvertently result in regression. A possible procedure for reducing tumor mass through a controlled intervention is also outlined.

Meteorological observations over the last four decades are of paramount importance to investigate the ongoing climate change. The assessment of the reliability of any climatic time series is thus mandatory to draw correct conclusions. This evaluation involves homogeneity tests to detect artificial discontinuities whose identification is facilitated by metadata availability. In this work, daily minimum and maximum temperature measurements collected in Padua, Italy, between 1980 and 2022, are examined. Hourly observations began in 1993 and since the aim is to study long term behavior of the temperature, the focus is on daily averages and extremes. Over this period, the weather station of Padua center underwent many changes, in location or instrument; therefore, some tests have been used to identify and remove the effects of these variations and obtain a homogeneous time series. The homogeneity tests applied must be able to identify change-points both in the middle and at the extremes of the series. Some well-known absolute tests have been applied to investigate shift in the mean value: Standard Normal Homogeneity test (SNH), Buishand U and range tests, Pettitt test, F-test, STARS. Some relative tests have been applied too, which are generally more reliable than absolute tests, because they consider the information from neighboring stations. As relative tests rely on the homogeneity and quality of the reference series, several nearby stations and two reanalysis datasets (ERA5 and MERIDA) have been considered, to enhance the picture of the local situation and provide more robust conclusions. The applied tests identify change-points in the years in which a change in instrument or location of the station have occurred, confirming that these changes have compromised the homogeneity of the series. The sub-series obtained splitting the observations in correspondence of these change-points have been homogenized with respect a selected period; corrections must be applied also to future measurements to extend the time series properly.

Fiber coupling efficiency is one of the key technical indicators of atmospheric laser communication, which directly affects the communication system BER. According to the optical fiber coupling efficiency model, the optical fiber coupling model under atmospheric slant link is established, and the relationship between wavelength, zenith angle, receiving aperture, altitude and coupling efficiency is studied through numerical simulation. Based on the principle of adaptive optics turbulence correction, the relationship between fiber coupling efficiency and adaptive optics order is established. A fast method for estimating the coupling efficiency based on Strehl ratio is proposed. According to the principle of laser communication system, the semi-physical simulation experimental system of atmospheric slant-range channel coupling efficiency is constructed, and the coupling efficiency test and analysis are completed.

The CRISPR/Cas9 gene editing system has enormous potential in the treatment of multiple genetic disorders. To fully harness this potential, it is essential to deliver CRISPR-Cas9 components safely and effectively into the nuclei of target cells. In this study, we tested the amphipathic cell-penetrating peptide LAH5, previously used for DNA delivery, to intracellularly deliver spCas9: sgRNA ribonucleoprotein (RNP) and RNP/single-stranded homology-directed repair (HDR) template. We discovered that the LAH5 peptide effectively formed nanocomplexes with both RNP and RNP/HDR cargo, and that these nanocomplexes were taken up by cells effectively. Peptide/RNP nanocomplexes were characterized for size and charge, and nanocomplexation with RNP and RNP/HDR cargo was demonstrated via an electrophoretic mobility shift assay. Various ratios of peptide/RNP nanocomplexes were functionally screened on fluorescent reporter cell lines for gene editing and HDR-mediated gene correction. Additionally, targeted gene editing of the CCR5 gene was demonstrated in various cell lines. This LAH5-based delivery strategy paves the way for the development of therapeutic delivery systems for CRISPR/Cas-based genomic engineering.

Sickle cell disease is characterized by stiff, “sickled” red blood cells that have difficulty moving through the bloodstream and do not efficiently carry oxygen. It is an inherited disease with severely limited treatment options, and is caused by a point mutation. Its prevalence in black and brown communities makes the already limited treatment options even less accessible. Base editing and prime editing are two relatively recent discoveries in the field of genome editing and were developed after the groundbreaking discovery of the CRISPR Cas9 system. While not fully tested, they hold a lot of promise in providing alternative treatment options for sickle cell disease. Both editing systems are able to install individual point mutations in the beta globin gene, which is where the sickle cell mutation occurs, and can thus cure sickle cell disease (in theory). In this paper we outline the mechanisms of CRISPR-Cas9 systems and base and prime editing, and provide insight into how to apply them to treat SCD. Further investigation should be done on specific editing systems and designs to use to ensure optimal treatment of SCD.

The purpose of this study is to propose a consecutive manufacturing process system to secure the productivity of excellent STKN540B steel tube in the respect of economy and safety as the supporting material for mega structures such as building, bridge and ship. The components of consecutive manufacturing are press-bending, orbital auto welding and steel tube correction. By using STKN540B a high-strength steel material with low yield point that requires a special manufacturing process unlike other steel materials, an actual tube manufacturing is carried out at each stage in this experimental study. With this, the quality of steel tube and the efficiency of the manufacturing process are analyzed to draw out some points to improve in the future.

This paper investigates the relationship between public debt and economic growth in the context of a panel kink regression with latent group structures. The proposed model allows us to explore the heterogeneous threshold effects of public debt on economic growth based on unknown group patterns. We propose a least squares estimator and demonstrate the consistency of estimating group structures. The finite sample performance of the proposed estimator is evaluated by simulations. Our findings reveal that the nonlinear relationship between public debt and economic growth is characterized by a heterogeneous threshold level, which varies among different groups, and highlight that the mixed results found in previous studies may stem from the assumption of a homogeneous threshold effect.

Given a quasi-definite linear functional u in the linear space of polynomials with complex coefficients let us consider the corresponding sequence of monic orthogonal polynomials (SMOP in short) (Pn)n≥0. For the Christoffel transformation u˜=(x−c)u with SMOP (P˜n)n≥0, we are interested to study the relation between u˜ and u(1)˜, where u(1) is the linear functional for the associated orthogonal polynomials of the first kind (Pn(1))n≥0 and u(1)˜=(x−c)u(1) is its Christoffel transformation. This problem is also studied for the Geronimus transformations.

We write the mutual information between an input speech utterance and its reconstruction by a Code-Excited Linear Prediction (CELP) codec in terms of the mutual information between the input speech and the contributions due to the short term predictor, the adaptive codebook, and the fixed codebook. We then show that a recently introduced quantity, the log ratio of entropy powers, can be used to estimate these mutual informations in terms of bits/sample. A key result is that for many common distributions and for Gaussian autoregressive processes, the entropy powers in the ratio can be replaced by the corresponding minimum mean squared errors. We provide examples of estimating CELP codec performance using the new results and compare to the performance of the AMR codec and other CELP codecs. Similar to rate distortion theory, this method only needs the input source model and the appropriate distortion measure.

Satellite measurements are one of the main sources of data on the state of the marine environment. To obtain information about the sea brightness coefficient , it is needed to correctly carry out atmospheric correction. In the presence of dust aerosol over the Black Sea, physically incorrect values of the spectral brightness coefficient often occur, and specifically negative values in the IR region of the spectrum. The main objective of the study is to evaluate the influence of dust aerosol on the spectral dependence of sea brightness, based on analytical calculations from the transfer theory using the principle of plane-parallel layers and results of validation of AERONET-OC field and remote sensing data. The work analyzes spectral dependence of the first error eigenvector of the standard atmospheric correction in the presence of dust aerosol. As result it is given that with an absorbing aerosol, the atmospheric correction error is described by the spectral course of molecular scattering, i.e. close to

With the development of designing and manufacturing level for micro-electromechanical system (MEMS) gyroscopes, the control circuit system becomes a key point to determine their internal performances. Nevertheless, phase delay of electron components may result in some serious hazards. This paper describes a real-time circuit phase delay correction system for MEMS vibratory gyroscopes. A detailed theoretical analysis is provided to clarify the influences of circuit phase delay on the in-phase and quadrature (IQ) coupling characteristics and zero rate output (ZRO) utilizing force-to-rebalance (FTR) closed-loop detection and quadrature correction system. By deducing the relationship between amplitude-frequency, phase-frequency of MEMS gyroscope and the phase relationship of the whole control loop, a real-time correction system is proposed to automatically adjust the phase reference value of phase-locked loop (PLL) and thus compensate for the real-time circuit phase delay. The experimental results show that the correction system can accurately measure and compensate the circuit phase delay in real time. Furthermore, the unwanted IQ coupling can be eliminated and the ZRO is decreased by 755% to 0.095°/s. This correction system realizes a small angle random walk of 0.978°/√h, and a low bias instability of 9.458°/h together with a scale factor nonlinearity of 255 ppm at room temperature. Besides, the thermal drift of ZRO is reduced to 0.0034°/s/°C at a temperature range from -20°C to 70°C.

UAS-based multi-spectral imagery is becoming increasingly popular for the improved monitoring and managing of various horticultural crops. However, for UAS data to be used as an industry standard for assessing tree structure and condition as well as production parameters, it is imperative that the appropriate data collection and pre-processing protocols are established to enable multi-temporal comparison. There are several UAS-based radiometric correction methods commonly used for precision agricultural purposes. However, their relative accuracies have not been assessed for data acquired in complex horticultural environments. This study assessed the variations in estimated surface reflectance values of different radiometric corrections applied to multi-spectral UAS imagery acquired in both avocado and banana orchards. We found that inaccurate calibration panel measurements, inaccurate signal-to-reflectance conversion, and high variation in geometry between illumination, surface, and sensor viewing produced significant radiometric variations in at-surface reflectance estimates. Potential solutions to address these limitations included appropriate panel deployment, site-specific sensor calibration, and appropriate BRDF correction. Future UAS based horticultural crop monitoring can benefit from the proposed solutions to radiometric corrections to ensure they are using comparable image-based maps of multi-temporal biophysical properties.

A computational methodology for the hydrodynamic analysis of horizontal axis marine current turbines is presented. The approach is based on a boundary integral equation method for inviscid flows originally developed for marine propellers and adapted here to describe the flow features that characterize hydrokinetic turbines. To this purpose, semi-analytical trailing wake and viscous-flow correction models are introduced. A validation study is performed by comparing hydrodynamic performance predictions with two experimental test cases and with results from other numerical models in the literature. The capability of the proposed methodology to correctly describe turbine thrust and power over a wide range of operating conditions is discussed. Viscosity effects associated to blade flow separation and stall are taken into account and predicted thrust and power are comparable with results of blade element methods that are largely used in the design of marine current turbines. The accuracy of numerical predictions tend to reduce in cases where turbine blades operate in off-design conditions.

Establishing an accurate mathematical model is the foundation of simulating the motion of marine vehicles and structures, and it is the basis of modeling-based control design. System identification from observed input-output data is a practical and powerful method. However, for modeling objects with different characteristics and known information, a single modeling framework can hardly meet the requirements of model establishment. Moreover, there are some challenges in system identification, such as parameter drift and overfitting. In this work, three robust methods are proposed for generating ocean hydrodynamic models based on Bayesian regression. Two Bayesian techniques, semi-conjugate linear regression and noisy input Gaussian process regression, are used for parametric and nonparametric gray-box modeling and black-box modeling. The experimental free-running tests of the KVLCC2 ship model and a multi-freedom wave energy converter (WEC) are used to validate the proposed Bayesian models. The results demonstrate that the proposed schemes for system identification of the ship and WEC have good generalization ability and robustness. Finally, the developed modeling methods are evaluated considering the aspects required conditions, operating characteristics and prediction accuracy.

Building energy demand impacts a myriad of interconnected economic, societal, and environmental aspects. As a result, Buildings Energy Models (BEM) play an important role in the process of urban design and planning. While previous studies have investigated the effects of building interventions on energy efficiency, their applicability may be limited due to the BEM’s high computational complexity. This limits their ability to systematically study important aspects of energy demand on a large scale. The development of Machine Learning Models (MLM) allows to design the required detailed analysis and solutions, while reducing the computational burden, making MLM attractive for urban designers. The capability of MLM to generalize well for multiple contexts (in our case, multiple buildings) is a crucial contributor to their applicability. However, the validation process in a wider context is often overlooked, therefore its generalization capabilities are not quantified. In this paper, we present a framework to train and validate a surrogate model derived from a physics-based BEM. Our method employs a Multiple Linear Regression model to predict Energy Use Intensity (EUI) for office buildings in Singapore using 36 input parameters (covariates), based on a training dataset of 23,000 samples. Model validation is performed by comparing the results of the Surrogate Model (SM) to a widely used BEM for a sample of 120 buildings. Our results indicate that the SM has an accuracy of NRMSE of 13%, NMBE of −3.56%, and R2 of 0.92, which suggests it can effectively and accurately predict building EUI. We also conduct a sensitivity analysis, which indicates that the parameters associated with internal loads and internal space usage are the most influential. Additionally, we present a reduced order model trained with only the 11 most influential parameters, which exhibits negligible loss in accuracy compared to the full SM while providing reduced complexity. Finally, we demonstrate an application of our SM to evaluate energy efficiency under uncertainty scenarios. The analytically derived results indicate a potential reduction of EUI of offices in Singapore from 227kWh/m2 to 99kWh/m2 by altering the building parameters that were identified as most influential.

Machine learning approaches are currently used to understand or model complex physical systems. In general, a substantial number of samples must be collected to create a model with reliable results. However, collecting numerous data is often relatively time-consuming or expensive. Moreover, the problems of industrial interest tend to be more and more complex and depending on a high number of parameters. High dimensional problems intrinsically involve the need of large data amount through the curse of dimensionality. That is why, new approaches based on smart sampling techniques are investigated to minimize the number of samples to be given to train the model, such as Active Learning methods. Here, we propose a technique based on a combination of Fisher information matrix and of Sparse Proper Generalized Decomposition that enables the definition of a new Active Learning informativeness criterion in high dimensions. We provide examples proving the performances of this technique on a theoretical 5D polynomial function and on an industrial crash simulation application. The results prove that the proposed strategy over-perform the usual ones.

In this brief communication, we propose the concept that capillary regression may represent a primary pathogenic process underlying COVID-19 infection, particularly in the serious and life-threatening manifestations of the disease. We suggest that the marked elevations of pro-inflammatory mediators that are observed in these seriously ill patients may directly induce capillary regression and endothelial cell (EC) loss. Recent autopsy studies are demonstrating EC loss leading to widespread microthrombi and associated tissue damage. Recent work has indicated that interleukin-1 beta (IL-1β), tumor necrosis factor-alpha (TNFα), and thrombin, individually and in combination, can potently cause capillary tube regression in experimental models in vitro and in vivo. Other pro-inflammatory mediators including interferon gamma (IFNγ), interleukin-4 (IL-4), and interleukin-13 (IL-13) were also shown to be pro-regressive and could be relevant mediators in COVID-19 patients. Interestingly, combinations of pharmacologic agents were identified that reduced capillary regression and protected capillary tube networks against these pro-inflammatory mediators. Such an approach might be an important therapeutic option going forward to treat key disease states where capillary regression plays a major underlying pathogenic role. Finally, if capillary regression is occurring in response to these pro-inflammatory mediators during COVID-19 infection, we suggest that combinations of blocking agents directed to these key pro-regressive mediators might be necessary to appropriately treat patients.

Let $n \geq 2$ be a fixed integer and $\mathcal{A}$ be a $C^*$-algebra. A permuting $ n $-linear map $ \mathcal{G} : \mathcal{A} ^{n} \rightarrow \mathcal{A} $ is known to be symmetric generalized $n$-derivation if there exists a symmetric $n$-derivation $ \mathfrak{D} : \mathcal{A} ^{n} \rightarrow \mathcal{A} $ such that $ \mathcal{G} \left(x_{1}, x_{2}, \ldots, x_{i} x_{i}^{\prime}, \ldots, x_{n}\right)= \mathcal{G} \left(x_{1}, x_{2}, \ldots, x_{i}, \ldots, x_{n}\right) x_{i}^{\prime}+x_{i} \mathfrak{D} (x_{1}, x_{2},\ldots, x_{i}^{\prime}, \ldots, x_{n})$ holds for all $x_{i}, x_{i}^{\prime} \in \mathcal{A} $. In this paper, we investigate the structure of $C^*$-algebras involving generalized linear $n$-derivations. Moreover, we describe the forms of traces of linear $n$-derivations satisfying certain functional identity.