The increasing demand for higher power in rocket launchers is driving the development of higher power nozzles, achieved essentially by increasing the expansion ratio. However, this can lead to flow separation and resulting unsteady, asymmetrical forces, called side loads, which can limit the life of both the nozzle itself and other engine components. If this problem can be overcome, engine performance can be significantly increased. Therefore, various separation control methods have been proposed, but none have been fully implemented to date due to the uncertainties associated with modeling and predicting the flow phenomena. A numerical study of high area ratio rocket engine is presented to analyze the aeroelastic performance of the structure under the condition of flow separation. The finite volume method, the 2nd order upwind scheme and the extended wall function are used to analyze the flow inside the rocket nozzle and the transition of the Free Shock Separation (FSS) to Restricted Shock Separation (RSS) separation pattern ) to be discussed in detail. Since the location of the flow separation point depends heavily on the flow.

The objective of this work was to investigate the deacidification of bio-oils (BOs) from triglyceride-based biomass through the application of liquid-liquid extraction (LLE) in a simple stage, using methanol and water as a binary solvent and feed/solvent ratio of 1/1. For this, the effects of process parameters such as the water content present in the solvent, the content of carboxylic acids present in the bio-oil, and the extraction temperature on the deacidification process through the efficiency and distribution coefficient were evaluated, as well as the effects of such parameters on the quality of deacidified bio-oils through physical-chemical analyzes and GC-MS analysis. The results show that such process parameters significantly affect the quality of deacidified bio-oils. The ideal condition to have the highest acid removal, i.e., the highest deacidification efficiency (72.65%), is the one in which the deacidification process is performed with aqueous methanol (5% water) at 35 °C and for BOs that have a total acid number (TAN) equal to 24.38 mg KOH/g. Therefore, the process of deacidification by LLE using aqueous methanol is a promising alternative for removing carboxylic acids and other oxygenated compounds, contributing significantly to the upgrading or improving biofuels produced by catalytic thermal cracking.

The first objective of this paper is to investigate the scaling behavior of liquid-vapor phase transition in FCC and BCC metals starting from the zero-temperature four-parameter formula for cohesive energy. The effective potentials between the atoms in the solid are determined using lattice inversion techniques as a function of scaling variables in the above formula. These potentials are split into repulsive and attractive parts as per the Weeks-Chandler-Anderson prescription, and used in the coupling-parameter expansion for solving the Ornstein-Zernike equation supplemented with an accurate closure. Thermodynamic quantities obtained via the correlation functions are used to obtain critical point parameters and liquid-vapor phase diagrams. Their dependence on the scaling variables in the cohesive energy formula are also determined. Equally important second objective of the paper is to revisit coupling parameter expansion for solving the Ornstein-Zernike equation. The Newton-Armijo non-linear solver and Krylov-space based linear solvers are employed in this regard. These methods generate a robust algorithm that can be used to span the entire fluid region, except very low temperatures. Accuracy of the method is established by comparing the phase diagrams with those obtained via computer simulation. Avoidance of the 'no-solution-region' of Ornstein-Zernike equation in coupling-parameter expansion is also discussed. Details of the method and the complete algorithm provided here would make this technique more accessible to researchers investigating thermodynamic properties of one component fluids.

The formation and functioning of membrane-less organelles (MLOs) is one of the main driving forces in the molecular life of the cell. These processes are based on the separation of biopolymers into phases regulated by multiple specific and nonspecific inter- and intramolecular interactions. Among the realm of MLOs, a special place is taken by the promyelocytic leukemia nuclear bodies (PML-NBs or PML bodies), which are the intranuclear compartments involved in the regulation of cellular metabolism, transcription, maintenance of genome stability, response to viral infection, apoptosis, and tumor suppression. According to the accepted models, specific interactions, such as SUMO/SIM, formation of disulfide bonds, etc., play a decisive role in the biogenesis of PML bodies. In this work, a number of bioinformatics approaches were used to study proteins found in the proteome of PML-bodies for their tendency to spontaneous liquid-liquid phase separation (LLPS), which is usually caused by weak nonspecific interactions. 205 proteins found in PML bodies have been identified. It has been suggested that UBC9, P53, HIPK2, and SUMO1 can be considered as the scaffold proteins of PML bodies. It was shown that more than half of the proteins in the analyzed proteome are capable of spontaneous LLPS, with 85% of the analyzed proteins being intrinsically disordered proteins (IDPs), and remaining 15% being proteins with intrinsically disordered protein regions (IDPRs). About 44% of all proteins analyzed in this study contain SUMO binding sites and can potentially be SOMYylated. These data suggest that weak nonspecific interactions play a significantly larger role in the formation and biogenesis of PML bodies than previously expected.

Liquid-liquid phase separation (LLPS) of proteins has been found ubiquitously in eukaryotic cells, critical in the controlling of many biological processes through forming a temporary condensed phase with different bimolecular components. TDP-43 is recruited to stress granules in cells and is the main component of TDP-43 granules and proteinaceous amyloid inclusions in patients with amyotrophic lateral sclerosis (ALS). TDP-43 low complexity domain (LCD) is able to demix in solution forming the protein condensed droplets. The molecular interactions regulating its LLPS were investigated at the protein fusion equilibrium stage, where the droplets stopped growing. We found the molecules in the droplet were still liquid-like but with enhanced intermolecular helix-helix interaction in the LCD. The protein would start to aggregate after about 200 minutes of lag time and aggregate slower than at the condition when the protein does not phase separate or the molecules have a reduced intermolecular helical interaction. A structural transition intermediate towards protein aggregation was also discovered involving a decrease of the intermolecular helix-helix interaction and a reduction in the helicity. Therefore, LLPS and the intermolecular helical interaction could help maintain the stability of TDP-43 LCD.

We present a theoretical modeling of a cylindrical tunable liquid crystal lens based on the modulation of the anchoring energy. This latter can be easily obtained by means of photoaligning techniques. The liquid crystal cell we propose exhibits strong anchoring at the top substrate and an anchoring energy with parabolic profile at the bottom substrate. The model describes the dependence of the focal length on the applied voltage and presents a theoretical study of lens aberrations. The results obtained are of general relevance and can be used to optimize the performances of every kind of liquid crystal lens with parabolic profile.

A review of influence of drag-reducing agents on curved pipe flows is presented in this work. In addition, this review outlined proposed mechanism, friction factor and fluid flux models for drag-reducing agents in curved pipe flows. Our finding reveals that drag reduction by additives in curved pipes is quite significant but generally lower than the corresponding drag reduction in straight pipes. It decreases with increase in curvature ratio and more pronounced in the transition and turbulent flow regimes. Drag reduction strongly depends on the polymers and surfactants’ concentrations as well as the bubble fraction of micro-bubbles. It is also reported that drag reduction in curved pipes depends on temperature and existence of dissolved salts in the fluids. Maximum drag reduction asymptote differed between straight and curved pipes and between polymer and surfactant. No definite conclusion could be drawn as regards drag reduction for two-phase flow in curved pipes due to the limited studies in this area. Many questions such as the mechanism of drag reduction in curved pipes and how drag-reducing agents interact with secondary flows still remained unanswered. Hence, some research gaps have been identified with recommendations for areas of future researches.

Keywords: liquid alloys, microstratification, dispersed particles, spontaneous dispersion, criteria for true (entropic) spontaneous dispersion, mechanisms of quasi-spontaneous dispersion, methods and results for assessing size of dispersed particles.

Radical changes in the idea of the organization of the intracellular space that occurred in the early 2010-s made it possible to consider the formation and functioning of the so-called membrane-less organelles (MLOs) based on a single physical principle: the liquid-liquid phase separation (LLPS) of biopolymers. Weak nonspecific inter- and intramolecular interactions of disordered polymers, primarily of intrinsically disordered proteins and RNA, play a central role in the initiation and regulation of these processes. On the other hand, in some cases, the "maturation" of MLOs can be accompanied by the "liquid-gel” phase transition, where other types of interactions can play a significant role in reorganization of their structure. In this work, we conducted a bioinformatics analysis of the propensity of the proteomes of two membrane-less organelles formed in response to stress in the same compartment, nucleolus, for spontaneous phase separation and looked at their intrinsic disorder predispositions. These nucleolar MLOs, amyloid bodies (A-bodies) formed in the response to acidosis and heat shock and nuclear stress bodies (nSBs), are characterized by the partially overlapping composition, but show different functional activities and morphologies. We show that the proteomes of these nucleolar biocondensates are differently enriched in proteins, many of with high potential for spontaneous LLPS that correlates with different morphology and function of these organelles. The results of these analyses allowed us to evaluate the role of weak interactions in the formation and functioning of these important organelles.

In recent years, the chiral biological effects of nanomedicines have become a subject of widespread interest. The research focus has been on understanding the influence of material chirality on cellular transcription and metabolism. Stress granules are membraneless organelles formed through liquid-liquid phase separation of G3BP1 proteins and related compartments. They have been extensively studied and proven to be closely associated with cellular damage repair and metabolism. However, the role and mechanism of chiral nanomaterials in modulating stress granules remain unknown. The aim of this study was to investigate the expression and structural characteristics of stress granules under the individual influence of chiral nanomaterials and in combination with chemotherapy. To achieve this, we constructed a library of chiral ligand-modified materials and employed immunofluorescence, live-cell imaging, and fluorescence recovery after photobleaching assays. We also used proximity labeling techniques combined with proteomics analysis to identify the protein corona adsorbed on the surface of the nanomaterials and explore their relationship with nanomaterial chirality. Our results demonstrate that the assembly of stress granules is chiral-dependent and can be regulated by chiral nanomaterials. Furthermore, we achieved enhanced chemotherapy sensitivity in cancer cells and protected normal cells by exploiting the chiral-dependent modulation of material assembly in stress granules. This study provides important insights into the regulation of membraneless cellular structures based on chiral biological effects.

We investigated fabrication of neodymium doped thin film optical waveguide-based devices as potential active sources for planar integrated optics. Liquid-phase epitaxial growth was used to fabricate neodymium-doped yttrium aluminum borate films on compatible lattice-matched un-doped yttrium aluminum borate substrates. We observed the refractive index contrast of the doped and un-doped crystal layers by differential interference contrast microscopy. In addition, characterization by X-ray powder diffraction, optical absorption and luminescence spectra demonstrated the crystal quality and uniformity and optical guiding of the resulting thin films.

Transient liquid phase (TLP) bonding of Al-6063 and UNS S32304 was performed using copper foil as an interlayer between the base metals. A compression load was applied normal to the specimens. Metallurgical examination of the produced joints showed three distinct regions including a reaction zone, diffusion affected zone and the base metals. The diffusion of copper into aluminum resulted in an Al-Cu eutectic structure. However, the oxide layer on the aluminum surface controlled the dissolution behavior of copper and the extent of its wettability with the base metals. Although voids and intermetallic compounds were detected at the interfaces of the processed joints, a defect free joint was produced at 570°C. In addition, the results from corrosion tests showed that the use of copper as an interlayer decreased the corrosion resistance of the joints. However, increase in thickness of the joining reaction zone with increasing bonding temperature was observed to increase corrosion resistance.

The present work reports the effective method for removal of inorganic and organic pollutants using membranes based on different carbonaceous materials. The membranes were prepared based on cellulose acetate (18 wt. %), polyvinylpyrrolidone as a pore generating agent (2 wt. %) and activated carbon (1 wt.%). Activated carbons were developed from residues after extraction of mushroom Inonotus obliguus using microwave radiation. It has been shown that addition of activated carbon the physical (porosity, equilibrium water content and permeability) and chemical (content of the surface oxygen group) properties of the membranes. The addition of carbon material has a positive effect on the removal of copper ions from their aqueous solutions by the cellulose-carbon composites obtained. Moreover, the membranes were proved to be more effective in removal of copper ions than iron ones and phenol. The membranes were found to show higher effectiveness in copper removal from a solution of the initial concentration 800 mg/L. The most efficient in copper ions removal was the membrane containing urea-enriched activated carbon.

Abstract: The quantitative analysis of the chromatographic behavior of basic compounds was performed in silico. The liquid chromatography (LC) data measured with pentyl-, hexenyl-, and octyl-bonded silica gels were analyzed in silico employing model phases. The main retention force was the van der Waals (VW) interaction, and the main desorption force was an electrostatic (ES) interaction. The contribution of hydrogen bonding (HB) was weak compared to that for acidic compounds. The quantitative explanation was achieved utilizing the calculated VW, HB, and ES energy values obtained from a molecular mechanics program. The electron localization was observed at the molecular interaction-site calculated MOPAC program. This fundamental approach was like that of explaining chemical reactions. The difference was electron localization in chromatography or electron transfer in a chemical reaction.

The theory and working principle of fabric phase sorptive extraction (FPSE) is presented that eloquently explains the mystery behind this new and powerful sample preparation technique. FPSE innovatively integrates the benefits of sol-gel coating technology and the rich surface chemistry of cellulose/polyester/fiberglass fabric, resulting in a microextraction device with very high sorbent loading in the form of an ultra-thin coating. This porous sorbent coating and the permeable substrate synergistically facilitate very fast extraction equilibrium. The flexibility of the FPSE device allows for direct insertion into original, unmodified samples of different origin. Strong chemical bonding between the sol-gel sorbent and the fabric substrate permits the exposure of FPSE devices to any organic solvent for analyte back-extraction/elution and to highly acidic or basic environments (pH 1-12) if required. A sol-gel derived sorbent, highly polar sol-gel poly(ethylene glycol) coating, was generated on cellulose substrates. Five cm2 segments of these coated fabrics were used as the FPSE devices for sample preparation using direct immersion. An important class of environmental pollutants, substituted phenols, was used as model compounds to evaluate the extraction performance of FPSE. The high primary contact surface area (PCSA) of the FPSE device and porous structure of the sol-gel coatings resulted in very high sample capacities and incredible extraction sensitivities for both the compound classes in a relatively short period of time. Different extraction parameters were evaluated and optimized. The new extraction devices demonstrated part per trillion level detection limits for substituted phenols, a wide range of detection linearity, and good performance reproducibility.

A hydrophilic silica-based stationary phase with surface bound N-acetylglucosamine (GlcNAc-silica) was prepared in house and characterized physically via Fourier transform infrared (FTIR) and thermogravimetric analysis (TGA) and chromatographically over a wide range of mobile phase compositions. While both FTIR and TGA confirmed the attachment of the GlcNAc ligands to the silica surface, the chromatographic evaluation of the GlcNAc-silica with polar and slightly polar standard solutes (e.g., sugars, nucleic acid fragments, phenolic and benzoic acid derivatives) yielded the typical hydrophilic interaction liquid chromatography (HILIC) behaviors in the sense that retention increased with increased solute’s polarity and the organic content (i.e., acetonitrile) of the hydro-organic mobile phase (i.e., ACN-rich mobile phase). Sugars derivatized with 1-naphthylamine (1-NA) and 2-aminoanthrcene (2-AA) such as xylose, glucose and short chains maltooligosaccharides constituted the most polar species for HILIC retention evaluation, and in addition the maltooligosaccharides offered a polar homologous series for gauging the hydrophilicity of the GlcNAc-silica in analogy with alkylbenzene homologous series and other nonpolar homologous for evaluating the hydrophobicity of non-polar stationary phases. On the other hand, the benzoic acid and phenolic acid derivatives were the probe solutes for evaluating the HILIC retention dependence of ionizable solutes on the pH of the mobile phase. Similarly, the nucleobase and nucleoside weak basic solutes as well as some typical cyclic nucleotide acidic solutes allowed the examination of the dependence of solute retention on the pH of the mobile as well as the polarity of the species.

The growth of solid particles during liquid phase sintering was modeled by the Cellular Automata method. The binary phase diagram and Fickian approach for the diffusion process were applied to simulate the chemical composition variation in liquid and solid phases during sintering. The Oswald-Ripening effect was considered during the dissolution of the solid phase in the liquid phase. It is used to define the probability of solid-phase dissolution by the liquid phase and develop the model to simulate the alloy with solid solubility. So, the microstructure could be modeled in the liquid phase sintering process.

The stability of twenty seven composts and organic substrates (including raw, less stable and stable materials) was assessed using two different liquid phase tests were carried out. One of the tests was introduced in 1998 and was based on the calculation of a Specific Oxygen Uptake Rate (SOUR). The newly introduced liquid phase test presented here is simpler to set-up and to perform that the older liquid phase test. It is based on the quantification of oxygen consumption in the headspace of a BOD bottle that contains the liquid-solid solution. The results indicate that a marginal correlation does exist between the main indices calculated from both tests. The correlation was stronger for the indices calculated for stable-processed organics than for the raw (unprocessed materials). The SOUR ranged from 1520 to 3650mg O₂/kg VS-h for the raw materials and from 110 to 1150 mg O₂/kg VS-h for the processed materials, respectively. The corresponding stability rate related index (LSRI₂₄) of the new liquid phase test introduced here ranged from 240 to 1180 mg O₂/dry kg-h for the raw materials and from 64 to 792 mg O₂/dry kg-h for the processed ones.

The development and improvement of methods for the synthesis of environmentally friendly catalysts based on base metals is currently an urgent and promising task of modern catalysis. Catalysts based on nanoscale magnetite and maghemite have fast adsorption-desorption kinetics and high chemical activity. The purpose of this work was to obtain magnetic composites, determine their physicochemical characteristics and verify their activity in the process of liquid-phase oxidation of phenol with oxygen. Magnetic nanocomposites were obtained by chemical co-deposition of salts of ferrous and trivalent iron. The synthesized magnetic composites were studied by X-ray diffractometry, energy dispersive X-ray fluorescence and Mössbauer spectroscopy, IR-Fourier spectroscopy, elemental analysis. To increase the catalytic activity in oxidative processes, the magnetite surfaces were modified using cobalt nitrate salt. Further, CoFe2O4 was stabilized by adding polyethylenimine (PEI) as a surfactant. Preliminary studies of the oxidation of phenol with oxygen, as the most typical environmental pollutant were carried out on the obtained Fe3O4, CuFe2O4, CoFe2O4/PEI catalysts. The spectrum of the reaction product shows the presence of CH in the aromatic ring and double C=C bonds, stretching vibrations of the C=O groups of carbonyl compounds; the band at 3059 cm–1 corresponds to the presence of double C=C bonds, the band at 3424 cm–1 hydroquinone compounds. The band at 1678 cm–1 and the intense band at 1646 cm–1 refer to vibrations of the С=О bonds of the carbonyl group of benzoquinone. Peaks at 1366 cm–1 and 1310 cm–1 can be related to the vibrations of C–H and C–C bonds of the quinone ring. Thus it was demonstrated that produced magnetic composites based on iron oxide are quite effective in the oxidation of phenol with oxygen.

Rapid, accurate, and convenient diagnosis is essential for effective disease management. Various detection methods, such as enzyme-linked immunosorbent assay, have been extensively used, with lateral flow immunoassay (LFIA) recently emerging as a major diagnostic tool. Nanoparticles (NPs) with characteristic optical properties are used as probes for LFIA, and researchers have presented various types of optical NPs with modified optical properties. Herein, we review literature on LFIA with optical NPs for the detection of specific targets in the context of diagnostics.

Infection with Zika virus (ZIKV), a member of the Flavivirus genus of the Flaviviridae family, typically results in mild self-limited illness, but severe neurological disease occurs in a limited subset of patients. In contrast, serious outcomes commonly occur in pregnancy that affect the developing fetus, including microcephaly and other major birth defects. The genetic similarity of ZIKV to other widespread flaviviruses, such as dengue virus (DENV), presents a challenge to the development of specific ZIKV diagnostic assays. Nonstructural protein 1 (NS1) is established for use in immunodiagnostic assays for flaviviruses. To address the cross-reactivity of ZIKV NS1 with proteins from other flaviviruses we used site-directed mutagenesis to modified putative epitopes. Goat polyclonal antibodies to variant ZIKV NS1 were affinity-purified to remove antibodies binding to the closely related NS1 protein of DENV. An antigen-capture ELISA configured with the affinity-purified polyclonal antibody showed a linear dynamic range between approximately 500 to 30 ng/mL, with a limit of detection of between 1.95 and 7.8 ng/mL. NS1 proteins from DENV, yellow fever virus, St. Louis encephalitis virus and West Nile virus showed significantly reduced reactivity in the ZIKV antigen-capture ELISA. Refinement of approaches similar to those employed here could lead to development of ZIKV-specific immunoassays suitable for use in areas where infections with related flaviviruses are common.

Firefighters Protective Clothing consist of several layers of different properties and functions. The layers create barriers against dangerous outer factor. However, they are also barriers to transport of sweat produced by human organism. It causes that very often sweat in the form of vapor is not transferred effectively from the human organism through the FPC to environment. This leads to sweat condensation on the skin of the FPC user causing his discomfort. In order to ensure as good as possible physiological comfort of firefighter while firefighting and other rescue actions it is necessary to take into consideration the transport of condensed sweat in the multilayer textile set creating the FPC. In the presented work four variants of multilayer textile sets for the FPC have been tested in the aspect of liquid moisture transport. Measurement was performed by means of the Moisture Management Tester (MMT290) – innovative instrument manufactured by the SDL Atlas. Obtained results showed that the transfer of sweat in liquid form occurs only in the inner, next to skin layer of the multilayer sets for the FPC.

The hydrodynamic behavior of the air-acetic acid system in a bubble column is studied using a differential pressure transmitter, double probe optical fiber probe, and the electrical resistance tomography (ERT) technique. The superficial gas velocity ranges from 0.016 to 0.094 m/s under ambient temperature and pressure. The influences of viscosity and surface tension on gas holdup, bubble rising velocity, and bubble chord distribution in the column are discussed with different mass fractions of an acetic acid solution. The results show that as the mass fraction of acetic acid increases, the surface tension of the liquid phase decreases, and the viscosity first increases and then decreases. This causes the gas holdup in the column to first increase and then decrease, and reaches the maximum value at an acetic acid mass fraction of 55% to 60%. The rising velocity of the bubbles in the column is high in the central region and has a low-value distribution near the wall. The bubble chord length distribution is concentrated, and the distribution of the bubble chord length in the column becomes narrow with any decrease in surface tension. Studying the hydrodynamic behavior of a bubble column with the air-acid system is of great significance considering the absence of data on air-organic acid systems.

To better understand the shape memory materials and self-healing materials, a new series of liquid-crystalline shape memory polyurethane (LC-SMPU) composites, named SMPU-OOBAm, were successfully prepared by incorporating 4-octyldecyloxybenzoic acid (OOBA) into the PEG-based SMPU. The effect of OOBA on the structure, morphology and properties has been carefully investigated. The results demonstrate that SMPU-OOBAm have liquid crystalline properties, triple-shape memory properties and self-healing properties. The incorporated OOBA promotes the crystallizability of both soft and hard segments of SMPU, and the crystallization rate of the hard segment of SMPU decreases when the OOBA-content increases. Additionally, the SMPU-OOBAm forms a two-phase separated structure (SMPU phase and OOBA phase), and it shows two-step modulus changes upon heating. Therefore, the SMPU-OOBAm shows triple-shape memory behavior, and the shape recovery ratio decreases with an increase in the OOBA content. Finally, SMPU-OOBAm shows self-healing properties. The new mechanism can be ascribed to the heating-induced “bleeding” of OOBA in the liquid crystalline state and the subsequent re-crystallization upon cooling. This successful combination of liquid crystalline properties, triple-shape memory properties and self-healing properties make the SMPU-OOBAm composites with many promise applications in smart optical devices, smart electronic devices and smart sensors.

Although there are a large number of databases available for regulatory elements, bottleneck has been created by the lack of bioinformatics tools for predicting types of mechanisms underlying actions of regulatory elements. To reduce the gap, we developed ARabidopsis Transcription regulatory Factor Domain-domain interaction Analysis Tool- Liquid-liquid phase separation (LLPS), Oligomerization, GO analysis (ART FounDATion-LOG), a useful toolkit for protein-nucleic acid interactions (PNI) and protein-protein interactions (PPI) analysis based on domain-domain interaction (DDI). LLPS, protein oligomerization, structural properties of protein domains, and protein modifications are major components in orchestrating spatio-temporal dynamics of PPI and PNI. Our goal is to integrate PPI/PNI information into development of prediction model for identifying important genetic variants in peach. The program unified inter-database relational keys by protein domains for facilitating inference from the model species. Key advantage of the program lies in the integrated information of related features: LOG, structural characterization of domain (e.g. domain linker, intrinsically disordered regions, DDI, domain-motif (peptide) interaction, beta-sheet and transmembrane helices), and post-translational modification. We provided simple tests to demonstrate how to use the program. The program may be applied to other eukaryotic organisms. The program codes and data are freely available for download at and https://sourceforge.net/projects/artfoundation-log/.

Waste glycerol can be subjected to various processing operations, including purification and re-fining, to obtain glycerol of appropriate purity. In addition, alternative methods of utilising waste glycerol are also being sought, e.g. by converting it into other valuable chemical products or biofuels. Therefore, various technologies are being developed to utilise this type of waste effectively and sustainably. The production of value-added products from waste glycerol is an important issue that determines the improvement of the economic viability of biofuel production and corresponds to the model of a waste-free and emission-free circular economy. This paper characterised the mechanisms and evaluated the efficiency of existing methods of microbiological utilisation of waste glycerol into liquid biofuels, including biodiesel, bioethanol and biobutanol, and identified further directions for the production of value-added products. In addition, a bibliographical analysis of publications re-lated to the production of liquid fuels and economically valuable products from glycerol was carried out, the progress of research and application work was assessed and directions for future research were identified.

Pyrethroid pesticides (PYRs) as the third most widely used pesticides, following organophosphorus and carbamate pesticides, which are of significant importance in the analysis and detection of vegetables. However, the current pretreatment technology for PYRs confronts challenges of difficult separation and low enrichment efficiency, resulting in a cumbersome and time-consuming pretreatment process with poor selectivity. Here, a simple and efficient magnetic solid-phase extraction (MSPE) strategy was developed to simultaneously purify and enrich five PYRs in vegetables, with the magnetic covalent organic framework nanomaterial COF-SiO2@Fe3O4 as an adsorbent. The COF-SiO2@Fe3O4 was prepared by a simple solvothermal conditions method, using Fe3O4 as magnetic core, benzidine and 3,3,5,5-tetraaldehyde biphenyl as two building units. COF-SiO2@Fe3O4 could effectively capture the targeted PYRs by virtue of its abundant π-electron system and hydroxyl groups. The impact of various experimental parameters on extraction efficiency was investigated to optimize the MSPE conditions, including adsorbent amount, extraction time, elution solvent type and elution time. Subsequently, method validation was conducted under the optimal conditions in conjunction with gas chromatography-mass spectrometry (GC-MS). Within the range of 5.00–100 μg·kg-1 (1.00–100 μg·kg-1 for bifenthrin and 2.5–100 μg·kg-1 for fenpropathrin), the five PYRs exhibited a strong linear relationship, with determination coefficients ranging from 0.9990 to 0.9997. The limits of detection (LODs) were 0.3–1.5 μg·kg-1, and the limits of quantification (LOQs) were 0.9–4.5 μg·kg-1. The recoveries were 80.2–116.7% with relative standard deviations (RSDs) below 7.0%. Finally, COF-SiO2@Fe3O4, NH2-SiO2@Fe3O4 and Fe3O4 were compared as MSPE adsorbents for PYRs. The results indicated that COF-SiO2@Fe3O4 was an efficient and rapid selective adsorbent for PYRs. This method holds promising prospects for the determination of PYRs in real samples.

Materials based on platinum metals with very good catalytic activity were tested in the reduction of p–nitrophenol (pNP) to p–aminophenol (pAP). The majority of presented catalytic materials are based on the adsorption of p–nitrophenol on the surface of the catalyst simultaneously with molecular hydrogen, coming from sodium borohydride in an aqueous medium, which reduces it. In the present paper, a catalytic material based on osmium dispersed in n–decanol or n–dodecanol is presented, which also works as an emulsion membrane, for the absorption of p–nitrophenol and molecular hydrogen at the n–alcohol aqueous solution interface. The hydrogenation of p–nitrophenol is carried out in a reaction and separation column in which the acid receiving phase emulsion is dispersed in the osmium nanodispersion, in n–alcohols. This emulsion circulates from the base of the column to its upper part in co-current or counter-current with the source phase consisting of p–nitrophenol and sodium borohydride. Experiments show that the circulation of counter-current phases is superior to that in co-current, and the emulsion based on n–decanol is more efficient than the one based on n–dodecanol. The increase in the pH difference between the source and receiving phases leads to the increase in the conversion of p–nitrophenol to p–aminophenol. The efficiency of separation of the reaction product in the receiving phase is lower than the conversion at the same operating time. The apparent catalytic rate constant (kapp) of the new catalytic material based on the emulsion membrane with nanodispersion of osmium nanoparticles (0.1×10−3 for n–dodecanol and 0.9×10−3 for n-decanol) is lower by an order of magnitude compared to those based on adsorption on catalysts from platinum metal group. The advantage of the tested membrane catalytic material is that it extracts p–aminophenol in the acid receiving phase. The paper proposes a mechanism of the studied reduction system.

In this paper, a semi-empirical model of air waves induced by falling rock is described. The model is composed of a uniform motion phase (velocity close to 0 m·s^-1) and an acceleration movement phase. The uniform motion phase was determined based on experimentally and the acceleration movement phase was derived by theoretical analysis. A series of experiments were performed to verify the semi-empirical model and elucidated the law of the uniform motion phase. The acceleration movement phase accounted for a larger portion with a greater height of the falling rock. Experimental results of different falling heights of the goaf showed close agreement with theoretical analysis values. The semi-empirical model could accurately and conveniently estimate the velocity of air wave induced by falling rock. Thus, the semi-empirical model can provide a reference and basis for estimating the speed of air waves and designing protective measures in mines.

Underwater Sensor Networks (UWSNs) can enable a broad range of applications such as resource monitoring, disaster prevention, and navigation-assisted. It is especially relevant for sensor nodes location in UWSNs. Global Positioning System (GPS) is not suitable for using in UWSNs because of the underwater propagation problems. Hence some localization algorithms based on the precise time synchronization between sensor nodes have been proposed which are not feasible for UWSNs. In this paper, we propose a localization algorithm called Two-Phase Time Synchronization-Free Localization Algorithm (TP-TSFLA). TP-TSFLA contains two phases, namely, range-based estimation phase and range-free evaluation phase. In the first phase, we address a time synchronization-free localization scheme base on the Particle Swarm Optimization (PSO) algorithm to decrease the localization error. In the second phase, we propose a Circle-based Range-Free Localization Algorithm (CRFLA) to locate the unlocalized sensor nodes which cannot obtain the location information through the first phase. In the second phase, sensor nodes which are localized in the first phase act as the new anchor nodes to help realize localization. Hence in this algorithm, we use a small number of mobile beacons to help achieve location without any other anchor nodes. Besides, to improve the precision of the range-free method, an extension of CRFLA by designing a coordinate adjustment scheme is updated. The simulation results show that TP-TSFLA can achieve a relative high localization ratio without time synchronization.

A novel polyphenol‑coated CoFe₂O₄ system was synthesized as a magnetic adsorbent by chemical oxidative polymerization process for magnetic solid-phase extraction of lawsone. The synthesized nanoadsorbent showed a spherical morphology with diameters under 50 nm by scanning electron microscopy images. The extraction efficiency of this adsorbent was studied towards the extraction of lawsone from saline aqueous solution in dispersion mode. Major parameters including the type and volume of desorption solvent, amount of sorbent, desorption time, extraction time, extraction temperature, ionic strength and pH were optimized. Under the optimum conditions the relative standard deviation in 0.005 µg mL^-1 (inter-day n = 6; intra-day: n = 6; and adsorbent to adsorbent n = 4) were obtained as 5.2, 8.07 and 11.7%, respectively. A linear calibration curve in the range of 0.003–0.5 µg mL^-1 with R² = 0.993 was obtained. The limit of detection and limit of quantification of the method were 0.001 µg mL^-1 and 0.003 µg mL^-1, respectively. The relative recovery percentages were in range of 90-96.4% for henna leaves, henna shampoo, and henna dermal lotion real samples.

The multiphase motors due to their reliability find new areas of application in the industry and transportation. Developing of any system with multiphase motors at first requires elaborate model of the system, define control mode and controllers. The model of control system for the six-phase drive is based on its conventional d-q mathematical model and indirect field-oriented control. Simulink model of six-phase drive with indirect field-oriented control and simulated with two types PID and PID fuzzy controllers. The simulation results, reflecting step response and provided speed reference law as well as load application at constant speed, are presented and analyzed. Fuzzy controller with 49 rules is considered and applied. Six-phase electric drive with field-oriented control at well-tuned PID controller has good step response specifications: settling time 0.13 s at starting without load, step response has no overshoot, small about 1 % short time decrease of speed at load of 5 Nm application. The system employing PID fuzzy controller shows slightly better results in response to torque application: the decrease in speed 1 % is eliminated in shorter time. Simulation results indicate the robustness of both systems with six-phase drive to disturbance and provide high quality transient specifications at determined reference speed.

Nowadays, the growing concern about improving thermal comfort in textiles, asphalt pavements and buildings has stimulated research into phase change materials (PCMs). However, the incorporation of PCMs directly causes mechanical impacts. Therefore, this study herein reported focuses on designing coaxial phase change fibres using commercial cellulose acetate (CA) or recycled CA obtained from cotton fabrics (CAt) as a coating and polyethylene glycol (PEG) 2000 as a core. The phase change fibres (PCF) were produced by wet spinning, varying the parameters: (i) CA concentration, molecular weight and source (virgin versus recycled); and (ii) PEG concentration and ejection. For phase change recycled fibres (PCFt), PEG concentration and ejection were varied. The fibres were assessed for their optical, chemical, thermal and mechanical properties. Bright-field microscopy images and Scanning Electron Microscopy (SEM) micrographs proved the coaxial structure. Fourier Transform Infrared spectroscopy (FTIR) confirmed the presence of PEG in the core. Thermogravimetric Analysis (TGA) proved the ability of PCFs to tolerate high temperatures. Differential Scanning Calorimetry (DSC) attested to the presence of PEG2000 peaks, since their melting points were close to those of virgin PEG2000, with a slight change in the PCFs and PCFts caused by the protective sheath of CA and CAt.

Epilepsy is a common neurological condition, typically diagnosed using Electroencephalogram (EEG). Large scale EEG datasets have recently been made publicly available, allowing the use of advanced Machine Learning (ML) algorithms to analyze EEG patterns associated with epilepsy. While most existing studies focus on identifying seizures in the EEG, few have tried to identify preictal EEG segments. Identifying preictal EEG segments are not only useful in developing early warning systems but also helps inform the course of treatment for the patient. In this study, we propose to represent EEG segments as images, instead of time-series data, and identify preictal EEG segments using a preexisting ML algorithm (YOLOv8) designed for image processing. Multiplexed images (containing the original EEG signal represented on a 2D grid, kurtosis, and spectral entropy) achieve the best accuracy of 95.75% on the dataset while images just containing the EEG signal result in an accuracy of 91.25%. Using only spectrograms, generated from the original EEG signal, results in an accuracy of 90.15%.

Although there are extensive literature reports on the use of gold nanoparticle (AuNP) based homogeneous assays for detection of biomolecules, very few experimental description and procedures involving their preparation are described. In this study, AuNPs conjugated to Bovine Serum Albumin or Envelope protein from Dengue II were developed as a homogeneous immunoassay for antibody detection. We report here optimization of key parameters to prepare an immunoassay like conjugation protein concentration, centrifugation time, electrolyte addition and assay temperature. We determined that saturating protein concentrations improved AuNPs surface coverage and uniformity of the assay and addition of sodium chloride improved sensitivity of the antibody detection method and assay stability. Furthermore, we showed that dynamic light scattering can be used to monitor changes in gold nanoparticles in the preparation and detection steps. Additionally, numerical simulations of the plasmonic optical response of AuNPs were carried out to scan for size-dependent response of the AuNPs. The AuNPs homogeneous immunoassay developed was further used in the detection of antibodies in vitro to detect Dengue virus infection.

The present work describes the optimization and validation of a highly selective and sensitive analytical method using solid phase extraction and liquid chromatography tandem mass spectrometry (SPE LC-MS/MS) for the determination of some frequently prescribed pharmaceuticals in urban wastewater received and treated by Sharjah sewage treatment plant (STP). The extraction efficiency of different SPE cartridges was tested and the simultaneous extraction of pharmaceuticals was successfully accomplished using hydrophilic-lipophilic-balanced reversed phase Waters^® Oasis HLB cartridge (200 mg/ 6 mL) at pH 3. The analytes were separated on an Aquity BEH C₁₈ column (1.7 µm, 2.1 mm x 150 mm) using gradient elution and the mass spectrometric analysis were performed in multiple reactions monitoring (MRM) selecting two precursor ions to produce ion transition for each pharmaceutical using positive electrospray ionization (+ESI) mode. The correlation coefficient values in the linear calibration plot for each target compound exceeded 0.99 and the recovery percentages of the investigated pharmaceuticals were more than 84%. Limit of detection (LOD) varied between 0.1-1.5 ng/L and limit of quantification (LOQ) was 0.3-5 ng/L for all analytes. The precision of the method was calculated as the relative standard deviation (RSD%) of replicate measurements and was found to be in the ranges of 2.2% to 7.7% and 2.2% to 8.6% for inter and intra-day analysis, respectively. All of the obtained validation parameters satisfied the requirements and guidelines of analytical method validation.

The adulteration of goat milk powder occurs frequently, cattle-derived and soybean-derived ingredients are common adulterants in goat milk powder. However, simultaneously and rapidly detecting cattle-derived and soybean-derived components is still a challenge. high throughput and efficient screening method for adulteration detection is need. In this study, a rapid method was developed to detect the adulteration of common cattle-derived and soybean-derived components simultaneously in goat milk powder by combining the CRISPR/ Cas12a system with recombinant polymerase amplification (RPA). A dual DNA extraction method was employed, primers and crRNA for dual detection were designed and screened, and a series of condition optimizations were carried out in this experiment. The optimized assay can rapidly detect cattle-derived and soybean-derived components in 40 min. The detection limits of both cattle-derived and soybean-derived components were 1% (w/w) for the mixed adulteration models. The established method was applied into a blind survey of 55 commercially available goat milk powder products. The results showed that 36.36% of the samples contained cattle-derived or soybean-derived ingredients, which revealed the noticeable adulteration situation in the goat milk powder market. This study realizes a fast flow of dual extraction, dual amplification and dual detection of cattle-derived and soybean-derived components in goat milk powder for the first time. It can be used for high-throughput and high-efficiency on-site primary screening of goat milk powder adulterants, and provide a technical reference for combating with food adulteration.

Redox mediators comprising I–, Co3+, and Ti3C2Tx MXene were applied to dye-sensitized solar cells (DSCs). In the as-prepared DSCs (I-DSCs), wherein hole conduction occurred via the redox reaction of I−/I3− ions, the power conversion efficiency (PCE) was not altered by the addition of Ti3C2Tx MXene. The I-DSCs were exposed to light to produce Co2+/Co3+-based cells (Co-DSCs), wherein the holes were transferred via the redox reaction of Co2+/Co3+ ions. A PCE of 9.01% was achieved in a Co-DSC with Ti3C2Tx MXene (Ti3C2Tx-Co-DSC), which indicated an improvement from the PCE of a bare Co-DSC without Ti3C2Tx MXene (7.27%). It was also found that the presence of Ti3C2Tx MXene in the redox mediator increased the hole collection, dye regeneration, and electron injection efficiencies of the Ti3C2Tx-Co-DSC, leading to an improvement in both the short-circuit current and the PCE when compared with those of the bare Co-DSC without MXene.

To enhance the applicability of dual-phase high-entropy alloys (HEAs) like Fe32Cr33Ni29Al3Ti3, fabricated via selective laser melting (SLM), a focus on improving their mechanical properties is essential. As part of this effort, heat treatment was explored. This study compares the microstructure and mechanical properties of the as-printed sample with those cooled in water after undergoing heat treatment at temperatures ranging from 1000 to 1200 ℃ for 1 hour. Both pre- and post-treatment samples reveal a dual-phase microstructure comprising FCC and BCC phases. Although heat treatment led to a reduction in tensile and yield strength, it significantly increased ductility compared to the as-printed sample. This strength-ductility trade-off is related to changes in grain sizes with ultrafine grains enhancing strength and micron grains optimizing ductility, also the influence of the content of FCC/BCC phases and dislocation density. In particular, the sample heat-treated at 1000 °C for 1 hour and then water-cooled exhibited a better combination of strength and ductility, a yield strength of 790 MPa, and an elongation of 13%. This research offers innovative perspectives on crafting dual-phase HEA of Fe32Cr33Ni29Al3Ti3, allowing for tailorable microstructure and mechanical properties through a synergistic approach involving SLM and heat treatment.

The thermodynamic phase behavior of charged polymers is a crucial property underlying their role in biology and various industrial applications. A complete understanding of the phase behaviors of such polymer solutions remains challenging due to the multi-component nature of the system and the delicate interplay among various factors, including the translational entropy of each component, excluded volume interactions, chain connectivity, electrostatic interactions, and other specific interactions. In this work, the phase behavior of partially charged, ion-containing polymers in polar solvents is studied by further developing a liquid-state (LS) theory with local short-range interactions. This work is based on the LS theory developed for fully-charged polyelectrolyte solutions. Specific interactions between charged groups of the polymer and counterions, between neutral segments of the polymer, and between charged segments of the polymer are incorporated into the LS theory by an extra Helmholtz free energy from the perturbed-chain statistical associating fluid theory (PC-SAFT). The influence of the sequence structure of the partially charged polymer is modeled by the number of connections between bonded segments. The effects of chain length, charge fraction, counterion valency, and specific short-range interactions are explored. A computational App for salt-free polymer solutions is developed and presented, which allows easy computation of the binodal curve and critical point by specifying values for the relevant model parameters.

A hybrid material, consisting of commercially available nitrocellulose (NC) membrane non-covalently modified with amino-polyethylene glycol functionalized reduced graphene oxide (NH2-PEG-rGO) nanoparticles, was successfully synthesized for oligonucleotide extraction. Fourier Transform Infrared Spectroscopy (FTIR) confirmed the modification of the NC membrane, revealing characteristic peaks of both compounds NC and NH2-PEG-rGO. Scanning Electron Microscopy (SEM) exhibited morphological changes in the NC/NH2-PEG-rGO hybrid membrane, marked by the introduction of NH2-PEG-rGO particles, resulting in a distinctly smothered surface compared to the porous surface of the NC control membrane. Wettability assays revealed hydrophobic behavior for the NC/NH2-PEG-rGO hybrid membrane, with a water contact angle exceeding 90°, contrasting with the hydrophilic behavior characterized by a 16.7° contact angle in the NC membrane. The performance of the NC/NH2-PEG-rGO hybrid membrane was evaluated for the extraction of ssDNA with fewer than 50 nucleotides from solutions containing various ionic species (MnCl2, MgCl2, and MnCl2/MgCl2). The NC/NH2-PEG-rGO hybrid membrane exhibited optimal performance when incubated in MgCl2, presenting the highest fluorescence emission at 525 relative fluorescence units (r.f.u.). This corresponds to the extraction of approximately 610 pg (≈13%) of the total oligo-DNA, underscoring the efficacy of the pristine material, which extracts 286 pg (≈6%) of oligo-DNA in complex solutions.

Glioblastoma is the most common and malignant primary brain tumor. Despite a century of research efforts, the survival of patients has not significantly improved. Currently, diagnosis is based on neuroimaging techniques followed by histopathological and molecular analysis of resected or biopsied tissue. A recent paradigm shift in diagnostics ranks the molecular analysis of tissue samples as the new gold standard over classical histopathology, thus correlating better with the biological behavior of glioblastoma and clinical prediction, especially when a tumor lacks the typical hallmarks for glioblastoma. Liquid biopsy aims to detect and quantify tumor-derived content, such as nucleic acids (DNA/RNA), circulating tumor cells (CTC), or extracellular vesicles (EV) in biofluids, mainly blood, cerebrospinal fluid (CSF), or urine. Liquid biopsy has the potential to overcome the limitations of both neuroimaging and tissue-based methods to identify early recurrence and to differentiate tumor progression from pseudoprogression, without the risks of repeated surgical biopsies. This review highlights the origins and time-frame of liquid biopsy in glioblastoma and points to recent developments, limitations and challenges of adding liquid biopsy to support the clinical management of glioblastoma patients.

The ionic liquid A327H+Cl- is generated by reaction of the tertiary amine A327 (industrial mixture of tri-octil and tri-decyl amines) and hydrochloric acid solutions. Further, the extraction of Au(III) by A327H+Cl- ionic liquid under various variables, including metal and ionic liquid concentrations, has been investigated. Results indicate that A327H+AuCl4- is formed, by an exothermic (ΔHº= -3 kJ/mol) reaction, in the organic solution. Aqueous ionic strength influences the formation constants values and the specific interaction theory (SIT) is used to estimate the interaction coefficient between AuCl4- and H+. Gold (III) is stripped using thiocyanate media, and from the strip solutions, gold is precipitated as gold nanoparticles.

A universally applicable method for the prediction of the isobaric heat capacities of the liquid and solid phase of molecules at 298.15 K is presented, derived from their “true” volume. The molecules’ “true” volume in A³ is calculated on the basis of their geometry-optimized structure and the Van-der-Waals radii of their constituting atoms by means of a fast numerical algorithm. Good linear correlations of the “true” volume of a large number of compounds encompassing all classes and sizes with their experimental liquid and solid heat capacities over a large range have been found, although noticeably distorted by intermolecular hydrogen-bond effects. To take account of these effects, the total amount of 1303 compounds with known experimental liquid heat capacities has been subdivided into three subsets consisting of 1102 hydroxy-group-free compounds, 164 monoalcohols/monoacids, and 36 polyalcohols/polyacids. The standard deviations for Cp(liq,298) were 20.7 J/mol/K for the OH-free compunds, 22.91 J/mol/K for the monoalcohols/monoacids and 16.03 J/mol/K for the polyols/polyacids. Analogously, 797 compounds with known solid heat capacities have been separated into a subset of 555 OH-free compounds, 123 monoalcohols/monoacids and 119 polyols/polyacids. The standard deviations for Cp(sol,298) were calculated to 23.14 J/mol/K for the first, 21.62 J/mol/K for the second, and 19.75 J/mol/K for the last subset. A discussion of structural and intermolecular effects influencing the heat capacities as well as of some special classes, in particular hydrocarbons, ionic liquids, siloxanes and metallocenes, has been given. In addition, the present method has successfully been extended to enable the prediction of the temperature dependence of the solid and liquid heat capacities in the range between 250 and 350 K.

Owing to the growing concerns due to dwindling fossil fuel reserves, increasing energy demand and climate emergency, it is imperative to develop and deploy sustainable energy technologies to ensure future energy supply as well as transition to the net zero world. In this context, there is great potential in the biorefinery concept for supplying drop in biofuels in the form of biodiesel. Biodiesel as a fuel can certainly bridge the gap where electrification or the use of hydrogen is not feasible, for instance heavy vehicles, farm and marine transportation sector. However, biodiesel industry also leads to formation of large amount of crude glycerol as the byproduct. Crude glycerol due to presence of several impurities may not be a suitable feedstock for all high value products derived from glycerol but fits well with glycerol esterification for producing glycerol acetins, which have numerous applications. This review critically looks at the processes using nanostructured solid/liquid acid catalysts for glycerol esterification including the economic viability of the scale up.

The presence of antibiotic residues in honey has recently become a growing public health concern due to the overuse of these products in beekeeping and their transfer to the food industry. The aim of this study was to develop and validate a simple, selective and sensitive method for the simultaneous identification and quantification of residues of twenty-two sulfonamides, trimethoprim and dapsone in honey using a rapid and reliable liquid chromatography–tandem mass spectrometry (LC–MS/MS) method. The developed method showed good linearity, specificity, precision (repeatability and intra-laboratory reproducibility) and recovery. The decision limit (CCalpha) ranged between 2.16-22.12 µg/kg for CCα, while the detection capability (CCbeta) was between 2.16- 2.67-27.36 µg/kg. The method proved to be rapid, reliable and effective for the determination of sulfonamides, trimethoprim and dapsone from honey samples. The average recoveries were estimated to be between 70 and 106%. The relative standard deviations (RSDs) were between 6-18%. In practice, the method is essential to check the honey sold on the market and ensure its safety before it reaches the consumer.

Control over the composition of III-V ternary nanowires grown by the vapor-liquid-solid (VLS) method is essential for bandgap engineering in such nanomaterials and fabrication of functional nanowire heterostructures for a variety of applications. From the fundamental viewpoint, III-V ternary nanowires based on group V intermix (InSbxAs1-x, InPxAs1-x, GaPxAs1-x and many others) present the most difficult case, because the concentrations of highly volatile group V atoms in a catalyst droplet are beyond the detection limit of any characterization technique and therefore principally unknown. Here, we present a model for the vapor-solid distribution of such nanowires, which fully circumvents the uncertainties that remained in the theory so far, and link the nanowire composition to the well-controlled parameters of vapor. The unknown concentrations of group V atoms in the droplet do not enter the distribution, despite of the fact that a growing solid is surrounded by the liquid phase. The model fits quite well the available data on the vapor-solid distributions of VLS InSbxAs1-x, InPxAs1-x and GaPxAs1-x nanowires grown with different catalyst. Even more importantly, it provides a basis for the compositional control of III-V ternary nanowires based on group V intermix, and can be extended over other material systems where two highly volatile elements enter a ternary solid alloy through a liquid phase.

This paper proposed three-dimensional numerical simulation method by coupling of electrostatic and fluid fields to evaluating the performance of electrical sensor in the concentration measurement of gas/solid two-phase flow. Compared with the static numerical simulation, this real-time dynamic 3-D simulation method can research on a designed capacitance sensor combining the dynamic characteristics of the two-phase flows for concentration measurement. Several fluid-electrostatic models of transmission pipes with different sensor structures are built. Under different test positions and different particle concentrations, the flow characteristics and the corresponding electric signals can be obtained, and the correlation coefficient between the concentration values and the capacitance values are used for performance evaluation of the sensors. The effects of flow regimes on concentration measurement are also been investigated in this paper. To validate the results of simulation, an experimental platform with horizontal straight pipe for phase volume concentration measurement of solid/air two-phase flow is built, and the experimental results agree well with simulation conclusions. The simulation and test results show that the coupling models can give constructive reference opinions for the sensor design and collection of installation position in different transmission pipelines, which are very important for the practical process of pneumatic conveying system.

: To improve the efficiency of rhizobial inoculation operations and address the current situation of rhizobial inoculation being labor-intensive, a spraying and control system for variable rate application (VRA) of liquid rhizobia was developed. The system can accurately regulate the spraying rate of liquid rhizobia according to the desired rate of rhizobia by incremental Proportional Integral Derivative (PID) closed-loop control algorithm, making it particularly suitable for precise spraying with small amounts. In the laboratory experiment of precise flow control, variation coefficient of spraying nozzle from 0.10 MP to 0.20 MP pressure were no more than 1.2%. A clear linear relationship was observed between the spraying rate and pressure. The maximum response time was 1.93 seconds, while the average response time was 1.62 seconds when controlling the spraying system for small amounts. Field trial was conducted in Heilongjiang Agricultural Xianghe Farm of China. Average seeds number and 100-seed weight of soybean plant with rhizobia inoculation treatment were better than control group, and average yield of spraying liquid rhizobia agent with full base fertilizer increased by 232.5 kg/hm2, representing a significant 7.4% improvement over the control group. The results of these trails clearly showed the positive effect of the spraying and control system for liquid rhizobial inoculation, which has superior to existing inoculation manners, and provides an important technical support for the widespread adoption of rhizobia technology.

A common task in the immunodetection of structurally close compounds is to analyze the selectivity of immune recognition: it is required to understand the regularities of immune recognition and to elucidate the basic structural elements which provide it. Triazines are compounds of particular interest for such a research due to their high variability and the necessity of their monitoring to provide safety of agricultural products and foodstuffs. We evaluated the binding of 20 triazines with polyclonal (pAb) and monoclonal (mAb) antibodies obtained using atrazine as the immunogenic hapten. A total of >3000 descriptors was used in QSAR analysis of binding activities (pIC50). Comparison of the two enzyme immunoassay systems showed that the system with pAb is much easier to describe using 2D QSAR methodology, while the system with mAb can be described using the 3D QSAR COMFA. Thus, for the 3D QSAR model of the polyclonal antibodies, the main statistical parameter q² (‘leave-many-out’) is equal 0.498, and for monoclonal antibodies q² is equal 0.566. Obviously, in the case of pAb, we deal with several targets, while in the case of mAb the target is one, and therefore it is easier to describe it using specific fields of molecular interactions distributed in space.

We report neutralization titer data against contemporary SARS-CoV-2 sublineages from an ongoing, open-label, phase 2/3 trial of a single 30-μg dose of monovalent Omicron XBB.1.5-adapted BNT162b2 vaccine. Healthy participants had previously received ≥3 doses of a US-authorized mRNA vaccine, with the most recent being a bivalent Omicron BA.4/BA.5-adapted vaccine administered ≥150 days before study vaccination. In this analysis, Omicron XBB.1.5, BA.2.86, and JN.1 serum neutralizing titers were assessed at baseline and 1 month after vaccination in a subset of ≥18-year-olds (N = 40) with evidence of previous SARS-CoV-2 infection. Immunogenicity was also evaluated in a demographically matched group of participants who received bivalent BA.4/BA.5-adapted BNT162b2 in another study (ClinicalTrials.gov Identifier: NCT05472038). The XBB.1.5-adapted BNT162b2 vaccine elicited higher XBB.1.5, BA.2.86, and JN.1 neutralizing titers than those elicited by bivalent BA.4/BA.5-adapted BNT162b2. Overall geometric mean fold rises in neutralizing titers from baseline to 1 month after vaccination were higher among participants who received XBB.1.5-adapted BNT162b2 than those who received bivalent BA.4/BA.5-adapted BNT162b2 for XBB.1.5 (7.6 vs 5.6), slightly higher for JN.1 (3.9 vs 3.5), and similar for BA.2.86 (4.8 vs 4.9). ClinicalTrials.gov Identifier: NCT05997290.

A novel determination method using flow-through cartridge purification and ultra-high-performance liquid chromatography coupled to tandem mass spectrometry (UPLC-MS/MS) was developed for the identification and quantification of 30 mycotoxins (aflatoxin B1, B2, G1, G2, sterigmatocysin, T-2 toxin, diacetoxyscirpenol, roquefortine C, methylergonovine, ergocornine, lysergol, enniatin A, enniatin A1, enniatin B, enniatin B1, beauvericin, deoxynivalenol, 3-acetylDeoxynivalenol, 15-acetylDeoxynivalenol, patulin, verruculogen, neosolaniol, gliotoxin, HT-2 toxin, wortmannin, zearalenone, α-zearalenol, β-zearalenol, α-zearalanol, and β-zearalanol) in feedstuffs. Mycotoxins were extracted from sample by 0.1% formic acid aqueous solution/acetonitrile (16/84 v/v), then purified by a Cleanert® MC clean-up column. As a result, the pigments and other matrices were efficient removed from the sample extract solution. The purified eluate was collected, then evaporated and redissolved by 0.1% formic acid aqueous solution/acetonitrile (70:30 v/v) for UPLC-MS/MS detection. A BEH Shield RP18 chromatographic column was employed for separation of 30 mycotoxins in a total of 14 min. Multiple-reaction monitoring (MRM) mode was applied for qualitative and quantitative analysis, and matrix calibration curves obtained with the external-standard method was used for quantitation of target analytes. Under optimized conditions, the linearity range was from 2 to 1000 ng/g, and the limit of quantification of the developed method was from 2 to 50 ng/g. The recoveries of 30 mycotoxins spiked in urine samples were from 72.0% to 118.5%, and the relative standard deviation was below 20%. The method was also well approved by certified reference sample, and applied on the real feedstuff samples testing successfully.

Colombia is the world's leading producer of mild washed arabica coffee and produces 12.6 million bags of green coffee, but at the same time 784,000 tons of waste biomass are dumped in open fields, of which only 5% is recovered or used. The objective of this project was to evaluate the production of platform chemicals from these coffee wastes. To achieve this, biomass characterization was carried out using proximate analysis, ultimate analysis and structural analysis. Hydrothermal valorization was carried out at a temperature range of 120-180 °C (LHW) and 180-260 °C (HTC) for one hour, the platform chemicals obtained were quantified by HPLC-IR, monitored by pH and conductivity, and the solid fraction was characterized by monitoring the functional groups in IR spectroscopy, and elemental analysis. Hydrolysis processes were obtained from 150 °C, production of platform chemicals from 180 °C and maximum concentration at 180 °C-4h, over 200 °C degradation of the products in the liquid fraction starts to take place. Homogeneous basic and acid catalysts were used to improve the yields of the reaction. The kinetics of the hydrolysis of lignocellulosic structures to sugars were also analyzed and described, and reaction orders of 1 (LHW), 3 (HTC) and their respective reaction rate equations were reported.

BACKGROUND: Few studies have examined the use of immunoassay urine drug testing of cancer patients in palliative care clinics. OBJECTIVES: We examined the frequency of immunoassay urine drug test (UDT) abnormalities and the factors associated with aberrancy at a safety-net hospital palliative medicine clinic. METHODS: A retrospective review of the electronic medical records of consecutive eligible patients seen at the outpatient palliative medicine clinic in a resource-limited safety net hospital system was conducted between September 1, 2015 and December 31, 2020. We collected longitudinal data on patient demographics, UDT findings, and potential predictors of aberrant results. RESULTS: Of the 913 patients in the study, 500 (55%) underwent UDT testing, with 455 (50%) having the testing within the first three visits. Among those tested within the first three visits, 125 (27%) had aberrant UDT results; 44 (35%) of these 125 patients were positive for cocaine. In a multivariable regression model analysis of predictors for aberrant UDT within the first 3 visits, non-Hispanic White race (odds ratio [OR]=2.13; 95% confidence interval [CI]: 1.03-4.38; p=0.04), history of illicit drug use (OR=3.57; CI: 1.78-7.13; p< 0.001), and history of marijuana use (OR=7.05; CI: 3.85-12.91; p< 0.001) were independent predictors of an aberrant UDT finding. CONCLUSION: Despite limitations of immunoassay UDT, it was able to detect aberrant drug taking behaviors in a significant number of patients seen at a safety net hospital palliative care clinic, including cocaine use. These findings support universal UDT monitoring and utility of immunoassay-based UDT in resource limited settings.

Simultaneous measurement of different substances from a single sample is an emerging issue to achieve efficient and high-throughput detection in several fields of application. Although immunoanalytical techniques have well-established and prevailing advantages over alternative screening analytical platforms, one of the incoming challenges for immunoassay is exactly multiplexing. The Lateral Flow Immunoassay (LFIA) is a leading immunoanalytical technique for onsite analysis thanks to its simplicity, rapidity and cost-effectiveness. Moreover, LFIA architecture is adaptable to multiplexing and therefore candidates as a possible answer to the pressing demand of multiplexing point-of-need analysis. The review present an overview of diverse approaches for multiplex LFIA, with a special focus on strategies based on new types of magnetic, fluorescent and colored labels

The absorption of medium-chain fatty acids (MCFA) depends on the solubility of these components in the gastric fluid. Parameters such as the total MCFA concentration, carboxyl ionization level, and carbon chain length affect the solubility of these molecules. Moreover, the enzymatic lipolysis of solubilized triacylglycerol (TAG) molecules may depend on the carbon chain length of the fatty acids (FAs) components and their positions on the glycerol backbone. This present study aimed at investigating the effect of electrolyte usually formed during the gastric digestion phase on the solubility of MCFA, and evaluating the influence of the FA carbon chain length on the lipolysis rate during the in vitro digestion simulation. The results obtained here showed that the increasing of electrolyte concentrations tend to decrease the mutual solubility of systems composed by the caproic and caprylic fatty acids + sodium chloride, sodium bicarbonate, and potassium chloride solutions. We also observed that a conventional version of the thermodynamic UNIQUAC model was able to correlate the liquid-liquid phase behavior of the electrolyte solutions. Regarding the in vitro digestion simulation, the experimental data indicated that the action of the pancreatic enzyme occurred preferentially in TAG molecules comprised of short and medium-chain fatty acids.

(200 words) Imidazolium ionic liquids containing acetylacetone, thenoyltrifluoroacetone, or 8-hydroxyquinoline, respectively, were used as the extracting agents for the separation of traces of iron (III) from its aqueous solutions with or without citric and oxalic acids. The results show that 8-hydroxyquinoline in imidazolium ionic liquids extract iron quantitatively from all the tested solutions including complexing ones, regardless indications of unexpected iron behavior/speciation.

Mutations in epidermal growth factor receptor (EGFR) occur in about 48% of Asian and 19% of Western patients with lung adenocarcinoma (LUAD), leading to its constitutive activation and subsequent uncontrolled cell proliferation. To counteract this, tyrosine kinase inhibitors (TKIs) have been developed, targeting EGFR activity. However, the emergence of metastases and resistance mutations often undermines the durability of the treatment response. Knowledge-based mechanistic models that replicate existing clinical trial outcomes, tailored to specific population characteristics, provide invaluable assistance in designing future clinical trials. These models are particularly effective in identifying optimal responders to specific treatments, thereby enhancing therapeutic efficacy. We have developed physiologically based pharmacokinetic (PBPK) models for gefitinib and osimertinib, representing two distinct generations of EGFR TKIs, to accurately simulate the drugs’ distribution within the primary tumor and metastatic sites following oral administration. These models were integrated with a pathophysiological mechanistic model of EGFR-mutant LUAD, enabling the representation of the effects of both gefitinib and osimertinib on EGFR activation-induced signaling pathways. This comprehensive model outputs detailed evolutions of the primary tumor and each metastatic site, facilitating the evaluation of patient progression in alignment with RECIST guidelines (version 1.1). Notably, the model encapsulates the heterogeneity within the tumor, through the representation of various subclones, each characterized by unique mutation profiles, thereby reflecting differential responses to treatment. Calibration of the model was achieved using publicly available data from the NEJ002 and FLAURA clinical trials. Rigorous visual predictive checks and statistical tests were employed to ensure the proper behavior of the model. The model adeptly replicated the time to progression observed in real clinical trials in EGFR-mutant LUAD patients receiving gefitinib or osimertinib as first-line therapy. In addition, the model was able to reproduce the results from a retrospective study comparing gefitinib and osimertinib, a study that was not used to inform the model. With a consistent virtual population as a reference, the combined model facilitated a comparative analysis of the efficacy of both treatments, thereby underscoring its utility in evaluating therapeutic strategies. The faithful replication of real-world data significantly enhances the credibility of our model, rendering it a vital investigational tool for deriving pertinent insights and informing treatment strategies, particularly in identifying optimal responders to various generations of EGFR TKIs. Following its consecutive prospective validations in the FLAURA2 and MARIPOSA trials, the model is poised to facilitate the generation of synthetic control arms in future clinical trials. This advancement promises a more nuanced analysis of covariate relationships, especially when comparing investigational treatments to established standards of care. Additionally, it potentially reduces the required patient cohort size in such trials, optimizing resource utilization.

This paper reports a novel fabric phase sorptive extraction-high performance liquid chromatography-ultra violet detection (FPSE-HPLC-UV) method for the simultaneous extraction and analysis of four phenyltin derivatives that include triphenyltin hydroxide, triphenyltin acetate, triphenyltin chloride and tetraphenyltin in environmental water (agricultural waste water and municipal waste water) and canned food samples. The selected analytes were well resolved by Waters Nova pack C18 column (3.9 x 150 mm, 4 µm particle size) in isocratic elution mode within 15 minutes. The new microextraction media has been analytically evaluated using phenyltin derivatives as model compounds. The factors affecting the extraction efficiency of FPSE have been evaluated and the optimum extraction conditions were determined. Under these optimum conditions, the limits of detection (LODs) for sol-gel C18 coated fabric phase sorptive extraction (FPSE) media in combination with HPLC-UV for the analysis of the phenyltin derivatives were in the range of 10-100 ng/mL with high precision (low relative standard deviation) at 10 ng/mL concentration with good absolute recoveries. To the best of our knowledge, this is the first FPSE extraction procedure applied to environmental water and canned food samples for the simultaneous determination of phenyltin derivatives and could be readily adopted as a rapid and robust green analytical tool for routine environmental and food analytical laboratories.

The polysaccharide-based chiral stationary phase (CSP) columns for high-performance liquid chromatography (HPLC) were applied in the separation of liquid crystalline racemic mixtures obtained based on (R,S)-2-octanol and were found to be highly effective in recognizing isomers of minor structural differences. The mobile phase (MP), which consists of acetonitrile (ACN)/water (H2O) at different volume ratios, was used. All measurements were made at room temperature. The order of the elution was also determined. The chromatographic parameters such as resolution - (Rs), selectivity - (α), and the number of theoretical plates, i.e., column efficiency - (N), were determined. The polysaccharide-based CSP columns have unique advantages in separation technology, and this study has shown the potential usefulness of the CSP columns in separating liquid crystalline racemic mixtures belonging to the same homologous series.

Considering the high potential of hydrogen (H₂) as a clean energy carrier, the implementation of high performance and cost-effective biohydrogen (bioH₂) purification techniques is of vital importance, particularly in fuel cell applications. In this context, membrane technology is a potentially energy-saving solution to obtain high-quality biohydrogen. The most promising poly(ionic liquid) (PIL) - ionic liquid (IL) composite membranes previously studied by our group for CO₂/N₂ separation, containing pyrrolidinium-based PILs with fluorinated or cyano-functionalized anions, were chosen as starting point to explore the potential of PIL–IL membranes for CO₂/H₂ separation. The CO₂ and H₂ permeation properties at the typical conditions of biohydrogen production (T =308 K and 100 kPa of feed pressure) were measured and discussed. PIL–IL composites prepared with [C(CN)₃]^– anion showed higher CO₂/H₂ selectivities and H₂ diffusivities compared to those containing [NTf₂]^– anion. All the membranes revealed CO₂/H₂ separation performances above the upper bound for this specific separation, highlighting the composite incorporating 60 wt% of [C₂mim][C(CN)₃] IL.

Open source software such as OpenDSS has given a lot of help to distribution network researchers and educators. With high penetration of distributed renewable energy resources into distribution network, tradition distribution steady state analysis software such as OpenDSS is faced with difficulty in handling distributed generators. Three-phase distributed generators are often modeled in sequence frame while unbalanced distribution network are usually modeled in phase frame. So a load flow in sequence-phase coupled frame is proposed to handle models described in both frames. Voltage controlled DGs which are difficult to cope with in OpenDSS are handled in proposed program. The steady state analysis platform is programmed with open source Modelica language and the main aim of this paper is to introduce an open source platform for active distribution network steady analysis include load flow and short circuit analysis which can be easily adopted and improved by other educators and researchers.

Essential oils (EOs) have great potential in inhalation therapy for the treatment of respiratory infections, however, innovative methods for evaluation of antimicrobial activity of their vapors are still needed. The current study reports validation of the broth macrodilution volatilization method for assessment of the antibacterial properties of EOs and shows growth-inhibitory effect of Indian medicinal plants against pneumonia-causing bacteria in liquid and vapor phase. Among all samples tested, Trachyspermum ammi EO exhibited the strongest antibacterial effect against Haemophilus influenzae, with minimum inhibitory concentrations of 128 and 256 µg/mL in the liquid and vapor phases, respectively. Furthermore, Cyperus scariosus EO was found to be non-toxic to normal lung fibroblasts were assessed by modified thiazolyl blue tetrazolium bromide assay. Chemical analysis performed using gas chromatography-mass spectrometry identified α-citral, cyperotundone, and thymol as the main constituents of Cymbopogon citratus, C. scariosus, and T. ammi EOs, respectively. In addition, β-cymene was identified as the major compound of T. ammi EO vapors when analyzed using solid-phase microextraction and gas-tight syringe sampling techniques. This study demonstrates the validity of the broth macrodilution volatilization method for antimicrobial screening of volatile compounds in the vapor phase and suggests the thera-peutic potential of Indian medicinal plants in inhalation therapy.

To improve efficacy and safety of sunscreen emulsions, UV‐filter skin permeation could be kept as low as possible by reducing UV‐filter content or changing emulsion composition. In this work, different lipid phase ratio (12, 14 and 16% w/w) were assessed for their ability to affect the technological and sensory properties of O/W emulsions in which bemotrizinol (BMTZ), a broad spectrum sunscreen agent, was incorporated free or loaded into nanostructured lipid nanocarriers (NLC) to reduce its release from the vehicle and, hence, its skin permeation. The following technological properties were evaluated in vitro by suitable methodologies: spreadability, viscosity, pH, occlusion factor, BMTZ release, sun protection factor (SPF). Sensory attributes were assessed by trained panelists in three different phases: before/during pick‐up, rub‐in, after application. Raising the lipid phase ratio led to an increase of viscosity and to a corresponding drop of spreadability while the incorporation of BMTZ‐loaded NLC determined a decrease of occlusion factor and an increase of SPF. No BMTZ release was observed from all emulsions. Sensory attributes were mainly affected by lipid phase ratio. These results suggest that lipid phase ratio and BMTZ incorporation into NLC could contribute to determine technological and sensory properties of O/W emulsions.

Although migraine belongs to the main causes of disability worldwide the mechanisms of its pathogenesis are poorly known, which is among the reasons that this disease is underdiagnosed and undertreated. As migraine diagnosis is based on the subjective assessment of symptoms, there is a need to establish objective markers of its occurrence and severity. Tryptophan (TRP) metabolism has been associated with the pathogenesis of neurological and psychiatric disorders. In the present work, we investigated an association between migraine and the urine concentration of TRP and its metabolites 5-hydroxyindoleacetic acid (5-HIAA), kynurenine (KYN), kynurenic acid (KYNA) and quinolinic acid (QA) in 21 low-frequency episodic migraine patients and 32 controls. Migraine patients displayed lower urinary levels of 5-HIAA and KYNA, but KYN and QA were enhanced as compared with the controls. Consequently, the patients were characterized by different values of the 5-HIAA/TRP, KYN/TRP, KYNA/KYN, and KYNA/QA ratios. Furthermore, urinary concentration of 5-HIAA was negatively correlated with Migraine Disability Assessment score, monthly migraine, and monthly headache days. A negative correlation between Patient Health Questionnaire 9 scores assessing depression. In conclusion, the urinary 5-HIAA level may be an easy-to-determine marker of migraine occurrence and severity and may contribute to the identification of migraine patients with depression.

On the system Au(III)-HCl-A324H⁺Cl^-, liquid-liquid extraction experiments were used to define the extraction equilibrium and the corresponding extraction constant, and the facilitated transport of this precious metal, from HCl solutions, across a flat-sheet supported liquid membrane was investigated, using the ionic liquid as carrier, as a function of hydrodynamic conditions, concentration of gold(III) (0.01-0.1 g/L), and HCl (0.5-6 M) in the feed phase, and carrier concentration (0.023-0.92 M) in the membrane. An uphill transport equation was derived considering aqueous feed boundary layer diffusion and membrane diffusion as controlling steps. The aqueous diffusional resistance (Δf) and the membrane diffusional resistance (Δm) were estimated from the proposed equation, being their values 241 s/cm an 9730 s/cm, respectively. The performance of the present carrier was compared against results yielded by other ionic liquids, and also it was investigated the influence that other metals had on gold(III) transport both from binary or quaternary solutions. Gold was finally recovered from receiving solutions as zero valent gold nanoparticles.

We have developed a simple, rapid, high-throughput RBD-based ELISA to assess the humoral immunity against emerging SARS-CoV-2 virus variants. The cDNAs of the his-tagged RBD proteins of the virus variants were stably engineered into HEK cells secreting the protein into the supernatant, and RBD purification was performed by Ni-chromatography and buffer exchange by membrane filtration. The simplified assay uses single dilutions of sera from finger-pricked native blood samples, purified RBD in 96-well plates, and a chromogenic dye for development. The results of this RBD-ELISA were confirmed to correlate with those of a commercial immunoassay measuring antibodies against the Wuhan strain, as well as direct virus neutralization assays assessing the cellular effects of the Wuhan and the Omicron (BA.5) variants. Here we document the applicability of this ELISA to assess the variant-specific humoral immunity in vaccinated and convalescent patients, as well as to follow the time course of selective vaccination response. This simple and rapid assay, easily modified to detect humoral immunity against emerging SARS-CoV-2 virus variants, may help to assess the level of antiviral protection after vaccination or infection.

In this paper, the deformation and phase transformation of disorder α phase at (α + γ) two phase region in as-forged Ti-44Al-8Nb-(W, B, Y) alloy are investigated by hot compression and hot packed rolling. Detailed microstructural evolution demonstrates that the as-deformed microstructure is significantly affected by deformation conditions. The mircrostructure differences are mainly due to temperature drop and strain rate. The evolution of α lamelae into α grains is detailed descripted. Moreover, the disorder α lamellae can also be decomposed into some new α grains by the assisted decomposition mechanism of γ grains. Microstructure evolution model of current TiAl alloy at 1250 °C during hot rolling is built.

In this work, we proposed a novel design of microfluidic mixer utilizing the amplified Marangoni chaotic advection induced by AC continuous electrowetting of a metal droplet situated in electrolyte solution, due to the linear and quadratic voltage-dependence of flow velocity at small or large voltages, respectively. Unlike previous researchers exploiting the unidirectional surface stress with DC bias at droplet/medium interface for pumping of electrolyte where the resulting flow rate is linearly proportional to the field intensity, dominance of another kind of dipolar flow pattern caused by local Marangoni stress at the drop surface in sufficiently intense AC electric field is demonstrated by both theoretical analysis and experimental observation, which exhibits a quadratic growth trend as a function of the applied voltage. The dipolar shear stress merely appears at larger voltages and greatly enhances the mixing performance by inducing chaotic advection between the neighboring laminar flow. The mixer design developed herein, on the basis of amplified Marangoni chaotic advection around a liquid metal droplet at larger AC voltages, has great potential for chemical reaction and MEMS actuator applications, because of generating high-throughput and excellent mixing performance at the same time.

This paper introduces the complex Rayleigh-van der Pol-Duffing oscillators (RVDOs), which are hyperchaotic and can be either autonomous or non-autonomous. The fundamental dynamics of the autonomous and nonautonomous complex RVDOs including dissipation, symmetry, fixed points and their stability are studied. These oscillators are found in various important fields of physics and engineering. The paper proposes a scheme to achieve phase synchronization (PS) and antiphase synchronization (APS) for different dimensional models. These kinds of synchronization are considered as generalization of several other types of synchronization. For this scheme we use the active control method based on Lyapunov stability theory. By analytically determining the control functions, the scheme achieved PS and APS. Our scheme is applied to study PS of hyperchaotic behaviours for two distinct hyperchaotic non-autonomous and autonomous complex RVDOs. Additionally, the scheme is employed to achieve APS of chaotic real non-autonomous RVDO and hyperchaotic complex autonomous RVDO, including those with different dimensions. Our work presents numerical results that plot the amplitudes and phases of these hyperchaotic behaviours, demonstrating the successful achievement of PS and APS.

Duplex Stainless Steels (DSS) and Superduplex Stainless Steels (SDSS) are an important class of stainless steels because they combine the benefits of austenite and ferrite phases, resulting in steels with better mechanical properties and higher corrosion resistance. Due to these characteristics are widely employed in various industries. However, the appearance of deleterious phases in their microstructure impairs the properties of DSS and SDSS. Among the deleterious phases, the main one is the sigma phase (σ), which can be nucleated when the steel is exposed to the temperature range between 650 °C and 900 °C, reducing its toughness and resistance to corrosion. In a previous work, Fonseca and collaborators used two descriptors of the microstructural path to analyze the formation of sigma phase (σ), SV, interfacial area per unit volume between sigma phase and austenite, and <λ>, mean chord length of sigma, both in function of the VV, volume fraction of sigma, known in the literature as microstructural partial path (MP). In this work, the contiguity ratio is applied for the first time to describe the microstructural path in the study of sigma phase precipitation in SDSS. The contiguity ratio showed that the distribution of the ferrite/sigma boundaries is homogeneous. Thus, it is reasonable to infer that one has a uniform distribution of sigma phase nuclei within the ferrite. About the kinetics of sigma phase formation, the DSS can be described by the classical JMAK equation, whereas for the SDSS, the kinetics tends to follow the Cahn model for grain edge nucleation. Finally, we present the 3D reconstruction of the sigma phase in SDSS. The results demonstrate that the sigma phase nucleates at the edges of the ferrite/austenite interfaces. Moreover, the sigma phase grows consuming the ferrite, but it is not fully interconnected.

Molecular-scale density fluctuations at equilibrium produce cavities in a liquid and can be analyzed to shed light on the statistics of the number of molecules occupying observation volumes of increasing radius. An information theory approach led to the conclusion that these probabilities should follow a Gaussian distribution function. This prediction has been confirmed by computer simulations in different liquid models if the size of the observation volume is not large. The reversible work of cavity creation is exactly linked to the probability of finding zero molecules in a given observation volume. The Gaussian formula for the latter probability is scrutinized to arrive at the enthalpy and entropy changes associated with cavity creation. The reversible work of cavity creation has a purely entropic origin due to the solvent-excluded volume effect produced by the inaccessibility of a given region of the configurational space. The consequent structural reorganization of liquid molecules leads to exactly compensating enthalpy and entropy changes. These results are in line with those obtained in a direct statistical mechanical study by Lee.

The calculation of the isobaric heat capacities of the liquid and solid phase of molecules at 298.15 K is presented, applying a universal computer algorithm based on the atom-groups additivity method, using refined atom groups. The atom groups are defined as the molecules' constituting atoms and their immediate neighbourhood. In addition, the hydroxy group of alcohols are further subdivided to take account of the different intermolecular interactions of primary, secondary and tertiary alcohols. The evaluation of the groups' contributions has been carried out by means of a fast Gauss-Seidel fitting calculus using experimental data from literature. Plausibility has been tested immediately after each fitting calculation using a 10-fold cross-validation procedure. For the heat capacity of liquids, the respective goodness of fit of the direct (R2) and the cross-validation calculations (Q2) of 0.998 and 0.9975, and the respective standard deviations of 8.2 and 9.16 J/mol/K, together with a medium absolute percentage deviation (MAPD) of 2.69%, based on the experimental data of 1133 compounds, proves the excellent predictive applicability of the present method. The statistical values for the heat capacity of solids are only slightly inferior: for R2 and Q2, the respective values are 0.9915 and 0.9875, the respective standard deviations are 12.19 and 14.13 J/mol/K and the MAPD is 4.65%, based on 732 solids. The predicted heat capacities for a series of liquid and solid compounds has been directly compared to those received by a complementary method based on the "true" molecular volume [1] and their deviations elucidated.

Plantar flexors (PF) spasticity is known to poorly correlate with active dorsiflexion (DF) impairment throughout the swing phase of hemiparetic gait. Spastic Cocontraction, instead, stemming from descending pathways, potentially misdirect antagonist PF activity opposing DF during swing. Electromyographic (EMG) recordings, while unable to differentiate between reflex-based and descending origins, may offer valuable insights into this distinction by exploring PF EMG activity after tibial nerve neurotomy (which eliminates PF spasticity). Eleven subjects with hemiparesis walking at comfortable velocity and 11 controls walking at comfortable and slow velocity, underwent kinematic and PF/DF EMG analysis. Five of the hemiparetic subjects underwent tibial neurotomy &gt;1 year prior. We evaluated spasticity at rest (Tardieu scale), maximal ankle dorsiflexion, tibialis anterior agonist recruitment and gastrocnemius medialis and soleus cocontraction coefficients during swing. At slow velocity, controls (0.80±0.12 m/s) moved at a similar pace as hemiparetic subjects (0.73±0.37 m/s, NS). Hemiparetic subjects showed: (i) reduced ankle DF across swing (ii) increased PF cocontraction, including before any DF (iii) higher cocontraction despite absent spasticity in tibial neurotomy subjects (iv) higher tibialis anterior recruitment. Increased PF cocontraction occurs in the absence of spasticity or ankle DF despite higher agonist recruitment. Spastic cocontraction is a major factor limiting active DF at swing, unlike spasticity.

The most recent and non-invasive approach for studying early-stage biomarkers is liquid biopsy. It implies the extraction and analysis of non-solid biological tissues (serum, plasma, saliva, urine and cerebrospinal fluid) without undergoing invasive procedures to determine disease prognosis. Liquid biopsy can be used for the screening of several components such as extracellular vesicles, microRNAs, cell-free DNA, cell-free mitochondrial and nuclear DNA, circulating tumor cells, circulating tumor DNA, transfer RNA and circular DNA or RNA derived from body fluids. Its application includes early disease diagnosis, surveillance of disease activity, and treatment response monitoring, with growing evidence for validating this methodology in cancer, liver disease, and central nervous system (CNS) disorders. This review will provide an overview of mentioned liquid biopsy components, which could serve as valuable biomarkers for the evaluation of complex neurological conditions, including Alzheimer’s disease, Parkinson's disease, amyotrophic lateral sclerosis, multiple sclerosis, epilepsy, stroke, traumatic brain injury, CNS tumors, and neuroinfectious diseases. Furthermore, this review highlights the future directions and potential limitations associated with liquid biopsy.

We report interfacial crystallization in droplets of saline solutions placed on superhydrophobic surfaces and liquid marbles filled with the saline. Evaporation of saline droplets deposited on superhydrophobic surface resulted in the formation of cup-shaped millimeter-scaled residues. The formation of the cup-like deposit is reasonably explained within the framework of the theory of the coffee-stain effect, namely, the rate of heterogeneous crystallization along the contact line of the droplet is many times higher than in the droplet bulk. Crystallization within evaporated saline marbles, coated with lycopodium particles, depends strongly on the evaporation rate. Rapidly evaporated saline marbles yielded dented shells built of a mixture of colloidal particles and NaCl crystals. We relate the formation of these shells to the interfacial crystallization promoted by hydrophobic particles coating the marbles, accompanied with the upward convection flows supplying the saline to the particles, serving as the centers of interfacial crystallization. Convective flows prevail over the diffusion mass transport for the saline marbles heated from below.

Fabric phase sorptive extraction (FPSE) combines the advanced material properties of sol–gel derived microextraction sorbents and the flexible and permeable fabric support to create a robust, simple and green sample preparation device. It simultaneously improves the extraction sensitivity, and the speed of the extraction by incorporating high volume of sponge-like porous sol–gel hybrid inorganic–organic sorbents into permeable fabric substrates that is capable of extracting target analytes directly from simple to complex aqueous sample matrices. For the first time, this technique was applied to the trace level determination of selected polycyclic aromatic hydrocarbons (PAHs) in environmental water samples using a non-polar sol–gel C18 coated FPSE media. Several extraction parameters were optimized to improve extraction efficiency and to achieve high detection sensitivity. Validation tests of spiked samples showed good linearity for four selected PAHs (R² = 0.9983–0.9997) over a wide range of concentrations (0.010-10 ng/mL). Limits of detection (LODs) and quantification (LOQs) were measured at pg/mL levels, 0.1–1 pg/mL and 0.3–3 pg/mL, respectively. Inter- and intra-day precision tests showed variations of 1.1–4.1% for four selected PAHs. Average absolute recovery values were in the range of 88.1–90.5% surpassed the recovery prediction model, with relative standard deviations below 5%. The developed FPSE-HPLC-FLD protocol was finally applied to analyze 8 environmental water samples. Out of four selected PAHs, fluoranthene (Flu) and phenanthrene (Phen) were the most frequently detected in four samples, at concentration levels of 5.6–7.7 ng/mL and 4.1-11 ng/mL, respectively followed by anthracene (Anth) and pyrene (Pyr) in two samples. The newly developed FPSE-HPLC-FLD protocol is simple, green, fast and economical, with adequate sensitivity for trace levels of four selected PAHs and seems to be promising in routine monitoring of water quality and safety.

In this research, atomistic molecular dynamics simulations are combined with mesoscopic phase-field computational methods in order to investigate phase-transformation in polycrystalline Aluminum microstructure. In fact, microstructural computational modeling of engineering materials could help to optimize their mechanical properties for industrial applications (e.g. directional solidification for turbine blades). As a result, a multiscale modeling approach is developed to find a relation between manufacturing variables (e.g. temperature) and microstructural properties of crystalline materials (e.g. grain size), which could be used to develop an advanced manufacturing process for sensitive applications. The results show that atomistic modeling of grain growth could be used as a first-principle approach in order to study phase transformation's kinetics, which could capture morphology of polycrystalline materials more accurately. On the other hand, phase-field mesoscopic approach needs less computational efforts, but still it relies on semi-empirical data to capture accurate phase transformation regimes, which makes this approach suitable for rapid examining of new manufacturing conditions as well as its effects on microstructural properties of polycrystalline materials.

The growing attention for plug-in electric vehicles, and the associated high-performance demands, have initiated a development trend towards highly efficient and compact on-board battery chargers. These isolated ac-dc converters are most commonly realized using two conversion stages, combining a non-isolated power factor correction (PFC) rectifier with an isolated dc-dc converter. This, however, involves two loss stages and a relatively high component count, limiting the achievable efficiency and power density and resulting in high costs. In this paper a single-stage converter approach is analyzed to realize a single-phase ac-dc converter, combining all functionalities into one conversion stage and thus enabling a cost-effective efficiency and power density increase. The converter topology consists of a quasi-lossless synchronous rectifier followed by an isolated dual active bridge (DAB) dc-dc converter, putting a small filter capacitor in between. To show the performance potential of this bidirectional, isolated ac-dc converter, a comprehensive design procedure and multi-objective optimization with respect to efficiency and power density is presented, using detailed loss and volume models. The models and procedures are verified by a 3.7 kW hardware demonstrator, interfacing a 400 V dc-bus with the single-phase 230 V, 50 Hz utility grid. Measurement results indicate a state-of-the-art efficiency of 96.1% and power density of 2.2 kW/dm³, confirming the competitiveness of the investigated single-stage DAB ac-dc converter.

Computational fluid dynamics (CFD) has, in the last decade, being an essential problem solving tool in industries such as pharmaceutical, pulp, petrochemical as well as Oil and Gas processing. The use of CFD for mixer design is unpopular in many countries in Africa. Therefore, this study investigates the characteristics of Brine-Surfactant mixing in a horizontal pipeline using CFD. The CFD is conducted by AnsysFluent software (licensed). A T-junction pipe is created and meshed with unstructured tetrahedral elements using design modeler. Discretization is done by Finite Volume Method (FVM), cell-centered scheme with Second-Order Upwind Scheme. The pressure term is introduced into the continuity equation by SIMPLE (Semi-Implicit Method for Pressure Linked Equations) algorithm. The kinetic epsilon model, also known as k-e model is administered to define the properties of the fluid and geometry, such as velocity, species mole fraction, pipe diameter. The boundary conditions is selected based on filed data. The rate of fluid flow in the primary region is 650 bbl/day at 400psi in 4in diameter pipeline, which is 100m long. The numerical simulation was based upon the governing equations such s continuity, Navier’s stoke, energy as well as specie transport equations. The findings shows that higher concentration results in increased mixing time, while 2% conc. of surfactant reaches homogeneity in 20 minutes at 72 meters of the pipe length. The result validated with field detail and the empirical result from literature, and is consistent. This study provide insight on industrial mixer design, chemical injection system, as well as gas pipeline design and optimization, especially in multiphase scale transport.

The individual and combined effects of extracellular products (ECP) from Arthrobotrys oligospora (Ao) and A. musiformis (Am) growth in liquid media against Haemonchus contortus L3 (HcL3) were assessed. The following methodological steps were established: isolation, morphological (MI) and molecular identification (Mol-I), assessment of nematocidal activity (NA) of fungal liq-uid culture filtrates (LCF) produced in two liquid media alone and in combination and finally, the myco-compound profile identification (MCP). The MI of both isolates suggested that the fungi corresponded to the species Ao and Am. This result was confirmed by PCR analysis followed by sequencing, alignment and obtaining coverage and similarity with respect to isolates reported in the NCBI database. Likewise, the highest Hc mortalities were 91.4% with individual LCF of Am and 86.2% with those of Ao at the highest concentration (100 mg/mL) in Czapek-Dox Broth. The combination of both LCF resulted in a similarly high larval mortality with no statistical differ-ences in relation to individual activity (P>0.05). The MCP showed the presence of alkaloids in both fungi. Coumarins, triterpenes and saponins were found only in Ao. Both fungi produced ECP with a high NA that could be identified and assessed in future studies as potential natural an-thelmintic compounds.

A recent paradigm shift in diagnostics of medulloblastoma allows the distinction of four major groups defined by genetic data rather than histology. This new molecular classification correlates better with prognosis and will allow better clinical management for therapies targeting druggable mutations, but also offers a new combination of monitoring tumor development in real-time and treatment response by sequential liquid biopsy. This review highlights recent developments after a century of milestones in neurosurgery, radio- and chemotherapy, but also controversial theories on the cell of origin, animal models and the use of liquid biopsy.

Turbulence is a fluid dynamic problem refractory to mathematical treatment. Examining a theoretical model of liquid water flowing in a cylinder at different Raleigh numbers, we propose a novel approach to elucidate the first stages of turbulent flows. The weakly bonded molecular assemblies of liquid water form a fluctuating branched polymer in which every micro-cluster displays different density. Against the common view of liquid water as an incompressible and continuous fluid, we suggest that the occurrence of transient local aggregates could be able to generate the vortices and eddies that are the hallmarks of turbulence. We quantify the local changes in velocity, diameter and density required to engender “obstacles” to the average flow. Then, we show how these microstructures, equipped with different Raleigh numbers and characterized by high percolation index, could generate boundary layers that contribute to micro-vortices production. We conclude that the genesis of turbulence cannot be assessed in terms of collective phenomena, rather is sustained, among many other factors, by the underrated microscopic inhomogeneities of fluids like liquid water.

Advances in reconfigurable liquid-based reconfigurable antennas are enabling new possibilities to fulfil the requirements of more advanced wireless communication systems. In this review, a comparative analysis of various state-of-the-art concepts and techniques for designing reconfigurable antennas using liquid is presented. First, the electrical properties of different liquids at room temperature commonly used in reconfigurable antennas are identified. This is followed by a discussion of various liquid actuation techniques in enabling high frequency reconfigurability. Next, liquid-based reconfigurable antennas in literature used to achieve the different types of reconfiguration will be critically reviewed. These include frequency-, polarization-, radiation pattern- and compound reconfigurability. The current concepts of liquid-based reconfigurable antennas can be classified broadly into three basic approaches: altering the physical (and electrical) dimensions of antennas using liquid, applying liquid-based sections as reactive loads; and implementation of liquids as dielectric resonators. Each concept and their design approaches will be examined, outlining their benefits, limitations, and possible future improvements.

We review a modern differential geometric description of the fluid isotropic motion and featuring it the diffeomorphism group structure, modelling the related dynamics, as well as its compatibility with the quasi-stationary thermodynamical constraints. There is analyzed the adiabatic liquid dynamics, within which, following the general approach, there is explained in detail, the nature of the related Poissonian structure on the fluid motion phase space, as a semidirect Banach groups product, and a natural reduction of the canonical symplectic structure on its cotangent space to the classical Lie-Poisson bracket on the adjoint space to the corresponding semidirect Lie algebras product. We also present a modification of the Hamiltonian analysis in case of the isotermal liquid dynamics. We study the differential-geometric structure of the adiabatic magneto-hydrodynamic superfluid phase space and its related motion within the Hamiltonian analysis and invariant theory. In particular, we construct an infinite hierarchies of different kinds of integral magneto-hydrodynamic invariants, generalizing those before constructed in the literature, and analyze their differential-geometric origins. A charged liquid dynamics on the phase space invariant with respect to an abelian gauge group transformation is also investigated, some generalization of the canonical Lie-Poisson type bracket is obtained.

The wood-based panel industry is experiencing an excessive accumulation of solid residues from the production of medium-density fiberboard (MDF) panels and moldings. It is possible to create new MDF products with acceptable physical and mechanical properties by revaluing MDF residues. Additionally, those products’ thermal properties can be improved by incorporating phase change materials (PCMs). This study aims to develop a wood-based fiberboard made of MDF residues, capable of storing thermal energy. Two types of PCMs, two PCM ratios, and two types of adhesives were used to produce eight different types of panels. The vertical density profile, thickness swelling, water absorption, internal bond (IB), and static bending properties – modulus of elasticity (MOE) and modulus of rupture (MOR) – were determined for each panel type. The specific heat of the panels was also determined. The results show the panels’ densities were greater than 700 kg/m3. Thickness swelling in water improved by 23% compared to the reference value of the control panel PCMs after PCM incorporation. The highest IB value was 1.30 MPa, which is almost three times the minimum required by regulation standards. The incorporation of PCMs reduced the panels’ bending properties compared to the properties of the control panels. Even though the values obtained are sufficient to comply with the minimum values set out in ANSI standard A208.2 with a MOE value of 2072.4 MPa and the values obtained are sufficient to comply with the minimum standards with a MOE value of 2072.4 MPa and a MOR value of 16.4 MPa. When microencapsulated PCM is used, the specific heat of the panels is increased by more than 100% over that of the control panels. This study develops a feasible alternative for using MDF residues: to create fiberboard that is capable of storing thermal energy and has adequate physical and mechanical properties.

The transport of indium(III), from HCl solutions, across a supported liquid membrane in flat-sheet configuration was investigated, being the carrier the ionic liquid HA324H⁺Cl^- (derived from the tertiary amine Hostarex A324 and hydrochloric acid). Different variables affecting the metal transport: hydrodynamic conditions in the source and receiving phases, metal and HCl concentrations in the source phase, and carrier concentration in the membrane phase, were investigated. Also the transport of indium(III) using carriers of various nature: ionic liquids, alcohol, ketone, phosphine oxide, etc., was compared. The metal transport was modelled describing the transport mechanism as: diffusion across the source diffusion layer, a fast interfacial chemical reaction, and diffusion of the InCl₄^--carrier complex through the membrane support. Diffusional parameters for the transport of indium(III), from the experimental data and the model, were estimated.

In this paper, the Phase-Scheduled-Command FXLMS algorithm with the phase error between the disturbance and command signal is analyzed in detail. The influence of the phase error on the convergence time constant, convergence rate, and performance of convergence is explained for both stationary and nonstationary disturbance signals case. For stationary disturbance, the phase error slightly increases the convergence rate but heavily increases the distance of the optimum vector from the initial value, leading to poor convergence time constant performance. For nonstationary disturbance, the existence of phase error leads to poor convergence performance in every step, resulting in poor sound profiling performance. And the estimation of the phase error influence is developed in the closed form. Simulations are performed to demonstrate the validity of the analysis results.

Exercise-induced muscle injury is one of the most common types of sports injuries. Skeletal muscle troponin I (skTnI) serves as an ideal biomarker in assessing such injuries, facilitating timely detection and evaluation. In this study, we develop a fluorescent sandwich lateral flow immunoassay (LFIA) combined with a desktop analyzer for rapid detection of skTnI. Through optimizing the reaction system, the assay achieves a satisfying detection performance, reaching a limit of detection (LOD) of 0.5 ng/mL with a turnaround time of 15 minutes. The proposed de-tection platform offers portability, ease of use, and high sensitivity, which facilitates the moni-toring of exercise-induced muscle injuries at the point of care. This feature is particularly advan-tageous for end-users, enabling timely detection of sports-related injuries and ultimately en-hancing prognosis and sports life.

Neurofilament light chain (Nf-L) is a well-known biomarker for axonal damage, however the corresponding circulating Nf-L analyte in CSF is poorly characterized. We, therefore, isolated new monoclonal antibodies against synthetic peptides, and these monoclonals were characterized for their specificity on brain-specific intermediate filament proteins. Two highly specific antibodies, ADx206 and ADx209, were analytically validated for CSF applications according to well-established criteria. Interestingly, using three different sources of purified Nf-L proteins, a significant impact on interpolated concentrations was observed. With a lower limit of analytical sensitivity of 100 pg/ml using bovine Nf-L as the calibrator, we were able to quantify the Nf-L analyte in each sample and these Nf-L concentrations were highly correlated to the Uman diagnostics assay (Spearman rho= 0.97, P<0.001). In the clinical diagnostic groups, the new Nf-L ELISA could discriminate patients with Alzheimer’s disease (AD, n=20) from frontotemporal lobe dementia (FTD, n=20) and control samples with subjective cognitive decline (SCD, n=20). Henceforth, this novel Nf-L ELISA with well-defined specificity and epitopes can be used to enhance our understanding of harmonizing the use of Nf-L as a clinically relevant marker for neurodegeneration in CSF.

Colorectal cancer (CRC) is the third most commonly diagnosed cancer worldwide, and despite advances in treatment, survival rates are still low; therefore, the development of novel drugs is imperative. Acetylcorynoline (ACN) is derived from Corydalis ambigua. The effect of ACN on colon cancer is still unknown. Therefore, we investigated its potential effects. Our data showed that ACN inhibited cell viability and proliferation. Moreover, ACN induced apoptosis and cell cycle arrest by inhibiting cell growth. In the present study, we hypothesized that ACN regulates c-Myc through CNOT2 or MID1IP1. ACN reduced the protein expression of oncogenic genes, decreased c-Myc half-life, and rapidly inhibited the serum stimulation response. Moreover, knockdown of CNOT2 and MID1IP1 with ACN increased apoptosis and further reduced the expression of oncogenes. In addition, ACN exhibited a synergistic effect with low-dose of 5-fluorouracil (5-FU) and doxorubicin (Dox). Collectively, our data demonstrates that ACN inhibited c-Myc expression through CNOT2 and MID1IP1 and induced apoptosis. These findings indicate the potential of ACN as a therapeutic agent against colon cancer.

Quantum physics is intrinsically probabilistic. The entropy of a quantum state quantifies the amount of randomness (or information loss) of such state. The degrees of freedom of a quantum state are position and spin, and upon their specification Born's rule in phase space defines randomness. We focus on the spin degree of freedom and elucidate the spin entropy. Then, we present some of its properties and show how entanglement increases spin entropy. Some speculative predictions on the decay of the $Z^0,W^{+,-}$ gauge bosons conclude the paper.

Viruses have established symbiotic relationships with almost every other living organism on Earth and at all levels of biological organisation, from other viruses up to entire ecosystems. In most cases, peacefully coexisting with their hosts, but in most relevant cases, parasitising them and inducing diseases. Viruses are playing an essential role in shaping the eco-evolutionary dynamics of their hosts, and have been also involved in some of the major evolutionary innovations either by working as vectors of genetic information or by being themselves coopted by the host into their genomes. Viruses can be studied at different levels of biological organisation, from the molecular mechanisms of genome replication, gene expression and encapsidation, to global pandemics. All these levels are different and yet connected through the presence of threshold conditions allowing for the formation of a capsid, the loss of genetic information or epidemic spreading. These thresholds, as it occurs with temperatures separating phases in a liquid, define sharp qualitative types of behaviour. These {\em phase transitions} are very well known in Physics. They have been studied by means of simple, but powerful models able to capture their essential properties, allowing to understand them. Can the physics of phase transitions be an inspiration for our understanding of viral dynamics at different scales? Here we review well-known examples of transition phenomena in virology and their simplest mathematical modelling approaches. We suggest that the advantages of abstract, simplified pictures used in Physics are also the key to properly understand the origins and evolution of complexity in viruses. By means of several examples, we explore this multilevel landscape and how minimal models provide deep insights into a diverse array of problems. The relevance of these transitions in connecting dynamical patterns across levels and their evolutionary and clinical implications are outlined.

Organic wastes and by-products from several activities, including food industries, farming, and animal husbandry, are a hygiene threat when aerobically decomposed. Therefore, their manage-ment is crucial for public health. In this direction, anaerobic digestion (AD) systems may be the solution by transforming waste into energy, which may decrease the environmental impact. However, their efficacy should be carefully examined. In this innovative study, we evaluated the physicochemical and microbial characteristics of liquid digestate (LD) retrieved from organic animal wastes in northern Greece using nanofiltration. Using treatment technologies including physical (solid-liquid separation, microfiltration and nanofiltration) and biological (anaerobic digestion), heavy metals and microbial (i.e., Salmonella spp., Escherichia coli, Enterococcus faecalis) concentrations reduced and nutrients were recovered. This work sets the basis for the efficient management of liquid digestate. Our method may enable the use of treated liquid digestate for unlimited irrigation water and other industrial applications of water. Apart from the sanitation process, the recovery of nutrients for soil fertilization seems to be a more sustainable way for fu-ture agricultural practices.

The phenomena of electrical conductivity and electromigration in metallic systems are related, since in both cases the basic physical process is the scattering of conduction electrons by metal ions. Numerous searches have been made for equations connecting the conductivity with electromigration. In the case of a liquid metal, when using the Drude-Sommerfeld (DS) conduc-tivity equation, it was not possible to obtain a quantitative relationship between these phenomena, which would be correct. Attempts to find such a relationship when taking into ac-count the N. Mott correction (g - factor) in the DS equation were unsuccessful. This article proposes a different correction (b - factor) to the DS equation, which takes into account the pos-sibility of varying the momentum transferred by the conduction electron to a metal ion during the scattering. This correction allows to establish a quantitative relationship between conductivity and electromigration, as well as between electromigration in various binary systems with common components, in agreement with experiment. The proposed theory describes well, in particular, two- and multi-component metal systems of any concentration (the consistency rule for triangles A-B, B-C, C-A). The value of b - factor smoothly changes depending on the heat of vaporization of the metal, per unit volume.

Epilepsy is one of the most common disorders of the central nervous system, impacting nearly 50 million people around the world. Heterogeneous in nature, epilepsy presents in children and adults alike. Currently, surgery is the only treatment that can cure epilepsy. However, not all individuals are eligible or have successful outcomes. Difficulty in accessing samples of human brain tissue along with advances in sequencing technology have driven researchers to investigate sampling liquid biopsies in blood, serum, plasma, and cerebrospinal fluid within the context of epilepsy. Liquid biopsies provide minimal or non-invasive sample collection approaches and can be assayed relatively easily across multiple time points, unlike tissue-based sampling. Various efforts have investigated circulating nucleic acids from these samples including microRNAs, cell-free DNA, transfer RNAs, and long non-coding RNAs. Here, we review nucleic acid-based liquid biopsies in epilepsy to improve understanding of etiology, diagnosis, prediction, and therapeutic monitoring.

Internal and mesoscopic variables differ from each other fundamentally: both are state space variables, but mesoscopic variables are additional equipped with a distribution function introducing a statistical item into consideration which is missing in connection with internal variables. Thus, the alignment tensor of liquid crystal theory can be introduced as an internal variable or as one generated by a mesoscopic background using the microscopic director as mesoscopic variable. Because the mesoscopic variable is part of the state space, the corresponding balance equations change into mesoscopic balances, and additionally an evolution equation of the mesoscopic distribution function appears. The flexibility of the mesoscopic concept is not only demonstrated for liquid crystals, but is also discussed for dipolar media and flexible fibers.

A simple model has been used to investigate the nature of chemical order in Na-Pb and Na-Hg liquid binary alloy at 700K and 673K respectively. The energy parameter obtained from the model was used to calculate the concentration dependent mixing properties such as Gibb’s free energy of mixing, Concentration fluctuations in the long wavelength limit and the Warren-Cowley chemical short range order parameter. Results obtained showed that both alloys are hetero-coordinated throughout the entire concentration and there is tendency for segregation and demixing to take place in the liquid alloys. We observed that Na-Hg liquid alloy is more strongly interacting binary alloy and chemically ordered than Na-Pb liquid alloy.

A drug repositioning effort supported the possible use of the anti-HIV drug etravirine as a treatment for Friedreich Ataxia (FRDA). Etravirine increases frataxin protein and corrects the biochemical defects in cells derived from FRDA patients. Because of these findings, and since etravirine displays a favorable safety profile, we conducted this pilot open-label phase 2 clinical trial assessing the safety and potential efficacy of etravirine in FRDA patients. Thirty-five patients were stratified into 3 severity groups and randomized to etravirine 200 mg/day or 400 mg/day. They were treated for 4 months. Efficacy endpoints were represented by changes in peak oxygen uptake and workload as measured by incremental exercise test, SARA score, cardiac measures, measures of QoL and disability. Data were collected 4 months before the start of the treatment (T-4), at the start (T0), at the end (T4) and 4 months after the termination of the treatment (T+4). Etravirine was well tolerated. Etravirine completely stopped the progression of the SARA score during the 4-months treatment period, compared to the 4 months pre and post treatment. It increased peak workload, while the improvement of peak oxygen uptake was not statistically significant. No changes in the cardiac measures were observed. Health and QoL measures showed a worsening at the suspension of the drug. In this open trial etravirine significantly improved neurological function and was generally safe and reasonably tolerated. This suggests that etravirine represents a potential therapeutic agent in FRDA deserving testing in a randomized placebo controlled clinical trial.

The research paper provides a mathematical framework for understanding phase shift in wave phenomena, bridging theoretical foundations with real-world applications. It emphasizes the importance of phase shift in physics and engineering, particularly in fields like telecommunications and acoustics. Key equations are introduced to explain phase angle, time delay, frequency, and wavelength relationships. The study also introduces the concept of time distortion due to a 1° phase shift, crucial for precise time measurements in precision instruments. The research also addresses infinitesimal wave energy loss related to phase shift, enriching our understanding of wave behavior, and impacting scientific and engineering disciplines.