Based on the dynamic strength variation mechanism of concrete under complex loading conditions, two approaches were devised: numerical testing and CT scanning, guided by the principle of minimizing energy dissipation. A methodology for calculating concrete's failure area and measuring its strength was developed. The analysis delves into the mechanisms behind failure patterns and variations in concrete specimen strength, focusing on crack initiation, development, and the resultant failure surface formed by crack propagation, along with the stress distribution in concrete specimens subjected to diverse loading conditions. Through evaluating the strength and computed failure area of concrete specimens, it is evident that the loading method influences both the strength and failure area of concrete specimens. In general, a larger failure area correlates with a higher measured strength.

Due to the continued deepening of today’s mining projects, there is a need to develop new or improved rockbolts that are strong and yielding and have high energy absorption when exposed to dynamic loading. Impact tests can provide useful information about the dynamic response of rockbolts but most laboratory tests involve high costs in preparation and result validation. Numerical modeling is an alternative that, in addition to complementing laboratory results, can be used to represent the process of deformation and energy absorption of support elements. In this paper the implementation and results obtained from a finite difference (FDM) numerical model are presented. The model functions as a simulation tool to illuminate all the elements that conform the large-scale (1:1) impact test and their behavior and influence on the dynamic response of a threadbar bolt (22 mm nominal diameter). The model was calibrated using published results and based on these results as well as parametric analysis, the response of each component (steel tube, grout, and bolt) could be identified and its behavior in terms of absorbed energy and displacement could be observed. Results show the model can provide important preliminary information to make design decisions about support elements design.

This paper seeks to model the crack propagation in of AAs (aluminum-alloys) 2524-T3 and 7050-T7452 subjected to fatigue loading at low temperature. Fatigue crack growth tests were performed on AAs 2524-T3 and 7050-T7452 subjected to constant-amplitude and actual random-spectra loading histories at room temperature of about 25 °C and at cryogenic temperature of -70 °C, respectively, to determine their crack growth properties and residual lives. The interaction mechanisms between cryogenic temperature and the fatigue load were deduced on the basis of the results of fractographic analysis. Temperature-dependent residual lives under actual random-spectrum load history were modeled based on a modified accumulation damage rule by accounting for the load interaction. Good correlation was achieved between the predictions and actual experiments, demonstrating the practical and effective use of the proposed method.

Hybrid reinforcement in a composite material (CM), in many situations, allows better govern material mechanical properties. Polymer matrix CM plate is reinforced with small particles and macro-fibers. Particles are oil shale ash (OSA) powder, macro-fibers – basalt fiber threads im-pregnated by matrix material. With the goal to find out elastic properties of the matrix- polymer with OSA, samples with its different concentrations were experimentally fabricated and their elastic properties were experimentally measured. Obtained data were used in numerical model-ling. Was observed polymer matrix composite slab, reinforced with OSA and three-dimensional (3D) basalt fiber fabric. Fabric are forming threads impregnated by matrix (polymer resin mixed with OSA particles). Damage accumulation in the stretched slab was modelled. Impregnated thread, in the modelling, is observed as a macro-fiber (MF) with averaged elastic properties. With the load increase MF in the material began to break. At first, appeared isolated single breaks. A probabilistic sequential MF rupture accumulation model was accepted and numerical-ly realized. The geometry of the reinforcing knitted fabric was modeled using the Leaf and Glaskin approach. In the knitted fabric highly, stressed MF cross-sections are observed as po-tential location where thread breakage can occur. If one thread breaks, the cross-sections of the adjacent threads experience the overload caused by this rupture. More overloaded crossection in the adjacent overloaded thread breaks and we obtain two adjacent broken MF designated as a defect with the size j=2. The probabilities of obtaining defect consisting of at least 2, 3, … j adjacent broken MF in the plate were calculated. The calculations continued until the rupture process becomes unstable (j→∞). The overstresses on adjacent threads in the CM were calculat-ed using the FEM three-dimensional numerical approach. Analytical and stochastic methods were used for the load-carrying capacity determination and different size defects accumulation in the hybrid composite material (HCM) plate. Also, was calculated the probability of the plate rupture.

Due to the long-term deformation settlement of foundations, issues such as damage and functional failure of buildings and structures have long been of concern in the engineering field. The creep of soil is one of the primary causes leading to long-term deformation of foundations. In this paper, the consolidation deformation, creep characteristics, and creep model of reconstituted saturated silty clay were studied by isotropic compression test and triaxial shear creep test. The results show that for the isotropic compression test, although the applied load adopts different stages of loading, as long as the final applied confining pressure is the same, the number of stages applied by the confining pressure has little effect on the final isotropic consolidation deformation of the sample and the triaxial undrained shear strength after creep. However, for the triaxial shear creep test, it is found that under the same final deviatoric stress, the final deviatoric strain of the sample is closely related to the number of loading stages of deviatoric stress. It shows that the more loading stages of the sample loaded with the same deviatoric stress, the smaller the final deviatoric strain, and the triaxial undrained shear strength of the sample after creep will increase. In addition, it is reasonable to determine the pore pressure dissipation of the sample to 95%((u0-u0)/u0=95%) as the main consolidation end time (tEOP) of the sample. The isotropic consolidation creep curves and the triaxial shear creep curves show certain nonlinearity. Then the logarithmic model and the hyperbolic model were used to fit the creep curves of the samples. It is found that the hyperbolic model has a better fitting effect than the logarithmic model, but for the triaxial shear creep test, the creep parameters of the sample change greatly. Therefore, studying the creep characteristics of soil under different pre-loading steps is of significant engineering importance for evaluating the long-term deformation of underground structures.

Peritoneal dialysis (PD) is a home-based efficacious modality for replacement of renal function in end-stage kidney failure patients but is still under-prescribed. A major limitation is the durability of the dialytic technique. Continuous exposure of the peritoneum to bioincompatible conventional glucose-based solutions is thought to be the main cause of long-term morpho-functional peritoneal changes eventually resulting in ultrafiltration failure. Poor PD solution biocompatibility is primarily related to the high glucose content, which is not only detrimental to the peritoneal membrane but has many potential metabolic side effects. To improve the clinical outcome and prolong the survival of the treatment, PD-related bioincompatibility urgently needs to be overcome. However, combining dialytic and osmotic efficacy with a satisfactory biocompatible profile proves quite difficult. New approaches targeting the composition of the PD solution include replacement of glucose with other osmotic agents and the addition of cytoprotective or osmo-metabolic compounds. Other strategies include infusion of mesenchymal cells or the administration of orally active agents. In the present article we review the current evidence on efforts to improve the biocompatible and functional performance of PD, focusing on studies performed in vivo (animal models of PD, human subjects on PD).

High hopes were associated with the new anti-angiogenic medicament, bevacizumab, which due to the possibility of binding to isoform A of vascular endothelial growth factor (VEGF), inhibited the creation of new blood vessels. However, not only blood vessels are responsible for the tumor cells' spread. During the process of tumor growth, lymphangiogenesis is mediated by other isoforms of the VEGF family, specifically VEGF-C and VEGF-D, which are independent of the bevacizumab action. Therefore, based on the mechanism of bevacizumab action and the processes of angio- and lymphangiogenesis, we formed three hypotheses: 1) if the lymph nodes in the primary ovarian cancers are metastatic, the outcome of bevacizumab treatment is worsened; 2) concerning the second-line treatment, bevacizumab will act in a weakened manner if the recurrence occurs in lymph nodes compared to local recurrences; 3) patients treated by bevacizumab are more likely to have recurrences in lymph nodes. These hypotheses raise the issue of the existing gap of knowledge, which concerns the effect of bevacizumab on the metastatic lymph nodes.

To investigate the impact of electrode structure on Electrical Stimulation Therapy (EST) for chronic wound healing, this study designed three variants of flexible microelectrodes (FMs) with Ag-Cu coverings (ACCs), each exhibiting distinct geometrical configurations: hexagonal, cross-shaped, and serpentine. These were integrated with PPY@PDA/PANI (3/6) hydrogel dressings. Comprehensive animal studies, coupled with detailed electrical and mechanical modeling and simulations, were conducted to assess their performance. Results indicated that the serpentine-shaped FM outperformed its counterparts in terms of flexibility and safety, exhibiting minimal thermal effects and a reduced risk of burns. Notably, FMs with metal coverings under 3% demonstrated promising potential for optoelectronic self-powering capabilities. Additionally, simulation data highlighted the significant influence of hydrogel non-uniformity on the distribution of electrical properties across the skin surface, providing critical insights for optimizing EST protocols when employing hydrogel dressings.

Immune checkpoint inhibitors (ICI’s) are in the forefront of advanced Non Small Cell Lung Cancer (NSCLC) treatment. Still, only 27- 46% of patients respond to initial therapy with ICI’s and of those, up to 65% develop resistance within four years. After disease progression (PD), treatment options are limited, with 10% Objective Response Rate (ORR) to second or third-line chemotherapy. In this context, ICI rechallenge is an appealing option for NSCLC. Most data on the efficacy of ICI rechallenge are based on retrospective real-world studies of small, heavily pretreated, and heterogeneous patient groups. Despite these limitations, these studies suggest that ICI monotherapy rechallenge in unselected NSCLC patient populations who discontinued initial ICI due to PD is generally ineffective, with a median Progression-Free Survival (PFS) of 1.6-3.1 months and a Disease Control Rate (DCR) of 21.4%-41.6%. However, there is a subpopulation that benefits from this strategy, and further characterization of this subgroup is essential. Furthermore, immunotherapy rechallenge in patients who discontinued initial immunotherapy following treatment protocol completion and progressed after an immunotherapy-free interval showed promising efficacy, with a DCR of 75-81%, according to post-hoc analyses of several clinical trials. Future research of ICI rechallenge for NSCLC should focus on better patient stratification, to reflect the underlying biology of immunotherapy resistance more accurately.

Strain-hardening cement-based composites (SHCC) are a novel class of fiber-reinforced concretes which exhibit high tensile strain capacity prior to failure localization. Although the tensile behavior of SHCC has been a matter of study in numerous research works, the behavior of these composites under other loading modes has scarcely been investigated. The article at hand addresses the mechanical behavior of two types of normal-strength SHCC subject to uniaxial tension, torsion, and combinations of torsional and axial loading. The SHCC under investigation were made with polyvinyl-alcohol (PVA) and ultra-high molecular weight polyethylene (UHMWPE) fibers, respectively. Digital Image Correlation (DIC) was applied to evaluate the multiple cracking process and crack opening modes in conjunction with the concretes’ axial and torsional loading histories. The study demonstrates the suitability of torsion experiments to assess the multi-axial and shear performance of SHCC, highlights the relation between multiple cracking and transfer capacity for shear forces, and emphasizes the importance of the type of reinforcing fibers on the shear strength and ductility of such composites.

Aim: The aim of this study was to investigate if tests used to assess core stability could be used to determine success in physiological tests applied to assess dynamic balance and agility for a young active population. Methods: Pearson's r correlation coefficient was used to assess the relationship between the core stability tests and the dynamic balance and agility tests. Evaluation of the tests was established using Cronbach's coefficient of variance as part of intra-rater reliability tests. An analysis of 18 active college aged students was conducted (males: n= 13, females: n= 5). The mean ± SD age for males was 19.2 years ± 3.22 years and for females was 19.4 years ± 1.14 years. Conclusion: The results indicate that there is no significant relationship between tests that assess core stability and tests conducted to assess dynamic balance in active young adults. With the exception of the abdominal flexion test, no significant relationship exists between the remaining core stability tests and agility T-Test. Core stability is not a determinant of balance and agility.

Background and Objectives: In this current state, Type 2 Diabetes Mellitus (T2DM) is more prevalent in the population, and metformin is used as a first-line medication for treating it. There was up surge in the utilization of alternative therapies in the management of diabetes. Especially in diabetes, Herbal medicines are considered safe and reliable by majority of the population. Aim: The purpose of this research is aimed to estimate the safety and efficacy of Polyherbal Metabolite Compounds (PHMC) capsules in adults with T2DM. Materials and Methods: In this study, 60 T2DM patients aged 18-60 years were randomly assigned to Groups A (30) receiving Metformin 500 mg twice a day after food and Group B (30) receiving PHMC capsule 500 mg twice a day after food in a prospective, randomized and open-label clinical study. The in-silico simulation study was performed to selected plants major compounds on target protein Insulin-like Growth Factor-1 (1K3A). Result: The PHMC is found to be safe and effective in the management of T2DM. The FBS, PPBS and HbA1c were significantly lowered (p

This research investigates the fatigue behaviour and fracture mechanics of high-performance concrete (HPC), including various compositions such as HPC with basalt aggregates (HPC-B), HPC with gravel (HPC-G), and high-strength coarse mortar (CM) static and cyclic tensile loading within the special priority program SPP 2020. The study aims to integrate fracture mechanics into structural analysis to enhance design guidelines for slender cross-sections and safety-related high-performance structural components. The experimental investigations reveal HPC-B's re-markable superiority, displaying higher compressive strength, modulus of elasticity, and tensile strength compared to HPC-G and CM. A modified disk-shaped compact tension (MDCT) based on ASTM standards, aided by digital image correlation (DIC) unveils fracture behaviour, empha-sizing fracture energy as a crucial parameter. HPC-B exhibits improved crack resistance and notch sensitivity reduction attributed to crushed basalt aggregates and enhanced interfacial transition zone (ITZ). The research scrutinizes factors like material characterization, aggregate morphology, stress levels, and displacement rate on crack formation. High-cycle fatigue tests show HPC-B's superior performance, and post-fatigue analysis reveals enhanced residual fracture toughness attributed to nano-level structural changes, stress redistribution and aggregate-matrix interac-tion. 3D image analysis via Computed Tomography (CT) scans captures mesostructural crack propagation and provide quantitative insights. This study advances the understanding of HPC fatigue behaviour, emphasizing the interplay of aggregate types, morphologies, and their dy-namic response to cyclic loading, offering valuable insights for optimizing design guidelines and fostering innovation in structural engineering.

Vancomycin is one of the ‘last-line’ classes of antibiotics used in the treatment of life-threatening infections caused by Gram-positive bacteria. Even though vancomycin was discovered in 1950s it was widely used after 1980s for the treatment of infections caused by methicillin-resistant Staphylococci as prevalence of such strains were increased. However, currently it is evident that vancomycin resistant Staphylococcusaureusandvancomycin-resistant Enterococci have been developed as a result of various reasons including use of avaparcin, which is an analog of vancomycin, as feed additive in livestock. In present day context, more attention should be paid on prevention of emergence of resistance for the antibiotics in order to keep antibiotics effective. In order to prevent emergence of resistance, proper guidance for the responsible use of antimicrobials is indispensable. Therefore, almost all stakeholders who use antibiotics should have in depth understanding on the antibiotic they use. As such, it is imperative to be aware of the important aspects of vancomycin. In the present review, efforts have been made to discussthe pharmacokinetics and pharmacodynamics, indications, emergence of resistance, control of resistance, adverse effects and alternative therapy for vancomycin.

The study assessed the trapping efficacy of locally-modified 1) Gravid Aedes Trap(GAT) lined with insecticide-treated net (ITN) as a killing agent, 2) Autocidal Gravid Ovitrap(AGO) with sticky board in the semi-field system (SFS) and field setting. Fully-balanced Latin square experiments were conducted to compare GAT lined with ITN vs AGO, both with either yeast or grass infusion. Biogents-Sentinel (BGS) with BG-Lure and no CO2 was used as standard trap for Aedes mosquitoes. In the SFS, GAT outperformed AGO in collecting both nulliparous (65% vs 49%,OR=2.22,[95%CI:1.89-2.60],p

Background: Despite a range of available treatments, there is a remaining unmet need for patients with severe post-partum hemorrhage (sPPH). Objective: This manuscript evaluated efficacy and safety of recombinant activated factor VIIa (rFVIIa) in sPPH management. Methods: An open-label, multi-center, randomized controlled trial (RCT; NCT00370877) and four observational studies (OS; OS-1 [NCT04723979], OS-2, OS-3 and OS-4) were analyzed regarding efficacy (need for subsequent invasive procedures, including uterine compression sutures, uterine or iliac artery ligation, arterial embolization or hysterectomy) and safety (incidence of thromboembolic events [TE] and maternal mortality) of rFVIIa for sPPH. The RCT, and OS-1 and OS-2, included a control group of women who did not receive rFVIIa (with propensity score-matching used in OS-1 and OS-2), whereas OS-3 and OS-4 provided descriptive data for rFVIIa exposed women only. Results: A total of 446 women exposed to rFVIIa and 1,717 non-exposed controls were included. In the RCT, fewer rFVIIa exposed women (50% [21/42]) had an invasive procedure versus non-exposed women (91% [38/42]; odds ratio 0.11, 95% confidence interval 0.03–0.35). In OS-1, more rFVIIa exposed women (58% [22/38]) had an invasive procedure versus non-exposed women (35% [13.3/38]; odds ratio 2.46, 95% confidence interval 1.06–5.99). In OS-2, 17% (3/18) of rFVIIa exposed women and 32% (5.6/17.8) of non-exposed women had an invasive procedure (odds ratio 0.33, 95% confidence interval 0.03–1.75). Across all included women, TEs occurred in 1.5% (0.2% arterial and 1.2% venous) of rFVIIa exposed women and 1.6% (0.2% arterial and 1.4% venous) of non-exposed women with available data. Conclusions: The positive treatment effect of rFVIIa in the RCT was not confirmed in the OS. However, the safety analysis did not show any increased incidence of TEs with rFVIIa treatment.

To explore the relevant factors that affect the efficacy of consciousness-regaining therapy (CRT)for prolonged disorder of consciousness(pDOC),a retrospective analysis was conducted on the case data of 114 patients with pDOC admitted to department of functional neurosurgery of Tianjin Huanhu Hospital from January 2019 to January 2022. Basic information on the cases,data on pDOC disease assessment, consciousness-regaining therapy methods, and efficacy evaluation were collected. A total of 114 patients were grouped and compared based on the efficacy at the end of treatment. Among them, there were 61 cases in the ineffective group and 53 cases in the effective group. There was no statistically significant difference (P>0.05) between the two groups in terms of gender, age, etiology, acute cerebral herniation, emergency craniotomy surgery, emergency decompressive craniectomy, time from onset to start of consciousness-regaining therapy , and duration of consciousness-regaining therapy(P>0.05). However, there were statistically significant differences (P<0.05) in terms of secondary hydrocephalus, , consciousness-regaining therapy methods, CRS-R grading before treatment, and GOSE score at 6 months after treatment. Binary logistic regression analysis showed that the type of therapy (OR=0.169, 95% CI: 0.057-0.508) was a related factor affecting the efficacy of consciousness-regaining therapy (P<0.05).Compared with non-invasive therapy, personalized awakening therapy using various invasive consciousness-regaining therapy methods can help improve the efficacy of therapy for pDOC.

In this study, we evaluated the antibacterial effect against Staphylococcus aureus and Salmonella Typhimurium in fried fish paste using floating electrode-dielectric barrier discharge (FE-DBD) plasma (1.1 kV, 43 kHz, N2 1.5 m/s, 1-60 min). In addition, quality evaluation (pH, VBN) of fried fish paste was conducted after FE-DBD plasma treatment. When FE-DBD plasma was treated for 1, 5, 10, 20, 30 and 60 min, S. aureus decreased by 0.16-1.13 log10 CFU/g, and S. Typhimurium decreased 0.25-1.13 log10 CFU/g. Both decreased > log10 CFU/g at 60 min. The D-value was 58.92 and R2 was 0.97 for S. aureus using first-order kinetics, and the D-value was 43.60 and R2 was 0.97 for S. Typhimurium using the Weibull model. There was no significant difference in pH after FE-DBD plasma treatment (p > 0.05). However, volatile basic nitrogen (VBN) significantly decreased as the treatment time increased (p < 0.05), and it was the lowest at 60 min to 3.46. Therefore, FE-DBD plasma treatment could be considered as a technology for preserving the quality of processed foods.

Steel construction is used more often these days as an alternative to the R.C.C. when light weight, high strength, large-span structures with a faster erection are required. Extensive studies have been done by researchers to study the seismic performance of reinforced concrete and steel structures, both in terms of elastic and inelastic behavior. Composite construction is also a recent advancement in the building industry with similar advantages. However, no emphasis has been given to the comparison between the inelastic behavior of steel and composite structures when subjected to lateral loads. This study compares the inelastic behavior of steel and a composite frame designed to have the same plastic moment capacity for structural members. The responses, such as the formation of hinges, story drifts, story displacements, lateral stiffness, ductility, maximum strength, energy dissipated, joint accelerations, and performance points, are compared with the aid of the building analysis and design software ETABS-18. For this, response spectrum analysis, pushover analysis and nonlinear direct integration time history analysis have been performed on both frames. For design and analysis, international codes such as IS 800-2007, IS 875 (Part I, II, IV), IS 1893-2002, AISC 360 (16 & 10) and FEMA 440 have been used. Part of this study also aims at comparing the response of these frames when subjected to near field and far field earthquakes. It can be concluded from the results that the post yield performance of the composite frame is superior to that of the steel frame when seismically excited.

In this paper, we investigate the effects of mean stress, multiaxial loading, and residual stresses on the fatigue life of springs. We study the fatigue life of a homogeneously stressed material subjected to cyclic loading with nonzero mean stress. Traditional methods for estimating fatigue life are based on Goodman and HAIGH diagrams. The formal analytical descriptions, namely "stress-life" and "strain-life" approaches, are found to be more suitable for the numerical methods. The fatigue analysis method described above, which describes crack growth per cycle, is extended. The extensions allow consideration of the mean stress of a load cycle. Closed-form expressions for crack length versus number of cycles are derived. The complementary effects on the fatigue life of springs, which ultimately have a significant influence on the fatigue life of springs, are summarized. For the proposed unified fatigue life functions, the ranges for the stress loading factor are extended by introducing the effective stress intensity. The solution leads to the factor range for the effective stress intensity, the effective mean value of the stress intensity factor and the effective stress ratio. The developed method assumes the homogeneous stress state in the whole spring element. For the non-homogeneously loaded structural elements, the weak-link concept is applied to account for fatigue.

The use of high strength to weight ratio laminated composites is emerging in marine industry and applications as a very efficient solution for improving productivity. Nevertheless, delamination between the layers is a limiting factor for the wider application of laminated composites, as it reduces the stiffness and strengths of the structure. Interleaving nanofibrous mats between layers of composite laminates has been proved to be an effective method for improving composites delamination resistance. This paper aims to characterize the effect of interleaved nanofiber on mode I interlaminar properties and failure mechanisms when subjected to static and fatigue loadings. For this purpose, virgin and nanomodified woven laminates were subjected to Double Cantilever Beam (DCB) specimens. Static and fatigue tests were performed and the tests were monitored by acoustic emission technique. The mechanical results showed a 130% increase of delamination toughness for nanomodified specimens in the static loadings and more crack growth resistance in the fatigue loading. The AE results revealed that different type of failure mechanisms was the cause of these improvements for the modified specimens compared with the virgin ones.

Electrification of society, increasing renewable energy sources and mobility charging lead to new loading patterns for power transformers. Dynamic load conditions induce enhanced mechanical stress on the transformers’ windings, potentially causing degradation of the solid insulation over time and compromising the transformer's short-circuit withstand capability. Thermal expansion of the windings, caused by losses in the copper conductors, occurring as the transformer is load-ed, increases the stress. Conversely, magnetic losses in the core and tie plate expansion contribute to a reduction in stress. This paper presents the effect of step changes in core losses and copper losses by on-line measurements of the clamping pressure, to better understand the mechanical stresses acting upon the solid insulation cellulose materials.

The paper presents the results of experimental studies and mathematical modeling of the effect of stress accumulation in thermosetting epoxy polymer "hot" curing on anhydride hardener. Stress accumulation occurs under cyclic thermomechanical action in a locked rod, similar effects are observed, for example, in thermoplastic elements subjected to the combined effect of mechanical loads and variable temperatures. Experimental results have shown that under cyclic thermomechanical loading during exploitation it is possible to accumulate residual stresses in the thermosetting polymer. A multi-element structural mathematical model with memory for thermomechanical load, which allows to consider the accumulation of residual thermal stresses, has been proposed. The results of modeling and experiment are compared. Based on the results, corrections are made in the approach to the application of this model to thermosetting polymers such as the epoxy resin under study. Considering the corrections, a good agreement (the difference is from 1 to 6%) with the results of experimental determination of stresses under complex cyclic thermomechanical load was obtained.

A macro network loading Model for multi-flow lines, time-varying and pedestrian congestion is proposed. The station hub is abstracted as a network of different types of nodes, and the flow of passengers at each node is calculated in real time for the purpose of simulating the hub's collection and distribution process. For correct transmission of passenger flow on heterogeneous networks, three types of indexes are proposed to distinguish the nodes, and then match the corresponding fundamental diagrams. This paper divides the update process of the dynamic network loading model into multiple processes by flow lines, and improves computational speed of DNL model. The proposed model is applied to the simulation of passenger flow collection and distribution in an actual hub station with multi-flow lines. The analysis results illustrate that the model can accurately reflect the realistic congestion facilities and explain the formation process of high-density areas. A rolling passenger flow control model based on optimal control theory is proposed. The effectiveness of the control model is verified based on simulation data.

The nature of the fracture and fragmentation process of concrete medium under blast loading is the transformation process of the medium from continuum to discontinuity, coupled with the significant rate correlation of concrete medium, its mechanical behavior presents a high degree of complexity. Problems such as grid distortion and even negative volume are often encountered in the finite element method and others when solving this problem, while the material point method can effectively avoid these problems. In addition, the widely used HJC concrete constitutive model does not take into account the segmented characteristics of the calculation function for dynamic increasing factor. Therefore, in this paper, firstly, the calculation function for dynamic increasing factor in the HJC concrete model is modified by SHPB experiment, and the improved HJC concrete model is proposed; secondly, the material point method simulation program is developed, and the improved HJC concrete model is embedded into the simulation program; finally, the simulation program is verified by numerical examples, and the results show that the developed simulation program can better simulate the fracture and fragmentation process of concrete medium under blast loading, especially the pulverization characteristics of the medium in the near zone of the load.

Today's unstable labor market increasingly requires flexibility and adaptability to cope with the threat of unemployment. It can cause distress in people and have a more significant negative impact on fragile workers, such as migrants. This study aimed to test whether a Career Counseling intervention designed for Migrants (CCfM) can develop Career Adaptability and, therefore, both Work Self-efficacy (WSe) and Job Search Self-efficacy (JSSe) perceptions. It was conducted in Italy and involved a sample of 233 migrants, who were asked to respond to a questionnaire available in three languages (Italian, French, and English). Data analysis showed that an improvement was demonstrated in all the variables considered, namely career adaptability (including concern, control, confidence, and curiosity), WSe, and JSSe, even though the CCfM was not directly designed to increase the last one. In addition, the development of career adaptability explained the increase in migrants' WSe and JSSe, and the initial level of career adaptability was found to explain the increase in WSe due to the initial positive level of curiosity.

In pediatric burn care, achieving swift healing with minimal complications remains paramount. This investigation assesses polyhexamethylene biguanide (PHMB)'s role in managing superficial partial-thickness burns in children, focusing on the effects of various patient-specific factors on recovery. Through a retrospective analysis of 27 pediatric cases treated with PHMB, we explored the impact of age, burn size, dressing frequency, treatment delay, cold therapy application, and analgesic usage on the duration until reepithelialization. Notably, the majority of patients benefited from early cold therapy, yet only 1 in 3 patients received analgesics. The study reveals a mean healing time of 8.78 days, with the extent of the burn showing a strong correlation to recovery speed. Most treatments were managed outpatient, evidenced by a negligible average hospital stay. Impressively, the intervention recorded no complications. Our findings endorse PHMB as a promising treatment for second-degree burns in young patients, offering healing efficiency on par with or surpassing traditional methods, without increasing complication risks. This investigation underscores the necessity for continued exploration into the optimal application of prehospital interventions and the comprehensive benefits of PHMB in pediatric burn management, advocating for future research aimed at assessing long-term outcomes, including scar quality and patient satisfaction.

Numerous elements, such as the composition and characteristics of carbon nanomaterials, the composition and characteristics of the matrix material, moisture levels, temperature, and loading circumstances, influence the piezoresistive behaviour of self-sensing cementitious composites. While some past research has explored the impact of some of these factors on the performance of self-sensing cementitious composites, additional investigations need to be conducted to delve into how loading conditions affect the sensitivity of self-sensing cement-stabilized composites. Therefore, this study explores the influences of various loading conditions (i.e., location of loading regarding the location of recording electrodes, and loading level) on the electromechanical performance of self-sensing cement-stabilized sand. To this end, firstly, the evaluation of the percolation threshold based on 10% cement-stabilized sand specimens containing various multiwall carbon nanotubes (MWCNTs) and graphene nanoplatelets (GNPs) was performed. Then, 10% cement-stabilized sand containing 4% MWCNTs/GNPs was tested under various cyclic compressive stresses. The results suggested that the distance between the loading area and the electrode location used for recording the electrical resistance significantly impacts the sensitivity of cement-stabilized sand. Optimal sensitivity was achieved when the electrodes were positioned directly beneath the loading area. Moreover, the study yielded that the stress sensitivity of self-sensing cement-stabilized sand increases proportionally with the stress level. Examination through scanning electron microscopy (SEM) demonstrated that the loading condition influences the bridging characteristics of carbon nanomaterials in cement-stabilized sand, leading to diverse electromechanical behaviors based on the loading condition. This study underscores the importance of considering specific parameters when designing the application of self-sensing cement-stabilized sand for practical field use.

Plasma treatment of soft polymers is the promising technique to improve biomedical properties. The response to the deformation of such materials is not yet clear. Soft elastic polyurethane treated with plasma immersion ion implantation is subjected to fatigue uniaxial loading (50000 cycles, frequency – 1 Hz, strain amplitude – 10, 20, 40%). The influence of the strain amplitude and the plasma treatment regime on damage character is discussed. Surface defects are studied in unloaded and stretched states of the material. As a result of fatigue loading, transverse cracks (with closed overlapping edges as well as with open edges deeply propagating into the polymer) and longitudinal folds which are break and bend inward, appear on the surface. Hard edges of cracks cut the soft polymer which is squeezed from the bulk to the surface.

This study aimed to investigate the efficacy of manual therapy and exercise versus synchronized telerehabilitation with self-manual therapy and exercise in treating Subacromial Pain Syndrome (SAPS). Sixty individuals diagnosed with SPS, aged 18-50 years, were randomly assigned to home exercise (HE), manual therapy (MT), and telerehabilitation (TR) groups. Treatment protocols were administered over 8 weeks and included specific exercises and therapy interventions. Out-come measures included Visual Pain Scale (VAS), shoulder range of motion (ROM) via gonio-metric measurements, Quick Disability Arm-Shoulder-Hand Problems Survey (Q-DASH), and patient satisfaction. Results revealed that both MT and TR groups exhibited reduced pain, in-creased ROM, lower Q-DASH scores, and higher patient satisfaction compared to the HE group. However, no significant differences were found between MT and TR groups in pain levels, ROM, Q-DASH scores, or patient satisfaction. The study concludes that both telerehabilitation and manual therapy effectively alleviate pain and are well-received by patients with SPS. Addition-ally, manual therapy demonstrates superiority in enhancing functional levels compared to exer-cise-based interventions. (Registration: NCT05200130)

In the present study the synthesis of gold nanoparticles (AuNPs) loaded with methotrexate (MTX) has been carried out in order to obtain controlled size and monodispersed nanocarriers, around 20nm. Characterization study shows metallic AuNPs with MTX polydispersed on the surface. MTX is linked by a replacement of citrate by the MTX carboxyl group. The drug release profiles showed faster MTX release when it is conjugated, which leads to the best control of plasma concentration. Also, the enhanced release observed at pH 5 could take advantage of the pH gradients that exist in tumor microenvironments to achieve high local drug concentrations. AuNPs-MTX conjugates were tested by flow cytometry against lung (A-549) and colon (HTC-116) cancer cell lines. Results for A-549 showed a lighter dose-response effect than for colon cancer ones. This could be related to the presence of folate receptors in line HTC-116 on the contrary than line A-549, supporting the specific uptake of folate-conjugated AuNPs-MTX by folate receptor positive tumor cells. Conjugates exhibited considerably higher cytotoxic effects compared with the effects of equal doses of free MTX. Anexin V-PI test sustain as cell death mechanism apoptosis, which is normally disabled in cancer cells.

In this paper, an extensive study on the operation, control and performance of a hybrid photovoltaic and wind turbine (PV-WT) system is presented. The study includes the operation of the hybrid systems under different weather conditions which are reflected on a change in the wind speed and irradiance. Various loading conditions are investigated such a change in active and reactive power demands for static and dynamic loads. The performance of the hybrid system is examined via MATLAB/SIMULINK simulations.

We compared the functional and morphologic effects in the loading dose between patients with treatment-naïve neovascular age-related macular degeneration treated with either intravitreal aflibercept (IVA) or intravitreal faricimab (IVF) injection in clinical settings. This retrospective study included 30 eyes from 28 patients who started IVA treatment between June and September 2022 and 30 eyes from 29 patients who started IVF treatment between October 2022 and March 2023. The mean best corrected visual acuity (BCVA) significantly improved from pre-treatment after loading dose in the IVA group (from 0.46 ± 0.46 to 0.36 ± 0.37, p=0.0047) and not in the IVF group (from 0.46 ± 0.41 to 0.44 ± 0.45, p=0.60). The mean central retinal thickness (CRT) significantly improved in both groups. The proportion of eyes with residual exudative change was greater in the IVF group than in the IVA group at 2 months after the first treatment. (p=0.026) We further analyzed the patients who obtained complete resolution of exudative changes after the loading dose. The IVA group had a significant improvement in BCVA, whereas the IVF group did not p=0.0047 and 0.20, respectively) Although IVA and IVF significantly improved the CRT, the BCVA improved significantly in IVA group and not in IVF group.

Dendritic Mesoporous Organosilica Nanoparticles (DMON) are a new class of biodegradable nanoparticles suitable for biomolecules delivery. In order to escape from the endosomes-lysosomes and to deliver biomolecules in the cytoplasm of cells, we studied photochemical internalization (PCI) and photodynamic therapy (PDT) of DMON. We added photosensitizers in the framework of DMON. DMON were also loaded with siRNA or FVIII factor protein. We made four formulations with four different photosensitizers, The photosensitizers allowed to perform imaging of DMON in cancer cells, but the presence of the tetrasulfide bond in the framework of DMON quenched the formation of singlet oxygen. Fortunately one formulation allowed to efficiently deliver proapoptotic siRNA in MCF-7 cancer cells leading to 31% of cancer cell death, without irradiation. For FVIII protein, it was loaded in two formulations with drug loading capacities (DLC) up to 25%. In conclusion DMON are versatile nanoparticles which allowed to load siRNA and to deliver it in cancer cells, and to load FVIII protein with good DLC. Due to the presence of tetrasulfide, it was not possible to perform PDT and PCI.

Non-compliant (NC) structures are often encountered in building construction in developing countries. This is a condition whereby erected buildings do not follow regulatory standards, especially in the provision of reinforcements. Therefore, under an earthquake load, the structures do not have sufficient resistance against such load. The structural elements of the building, which often have NC conditions, are the beam-column joints because they do not contain adequate shear reinforcements due to installation difficulty. This study aims to determine the structural performance of the reinforced concrete (RC) frame, which has a reinforcement deficiency in the beam-column joints. Numerical simulation was conducted on the Kakaletsis structure model by modifying the reinforcement details at the joints to represent the NC conditions. The non-linear modeling and analysis of the structural model were carried out using ATENA software. The analysis showed that the reduction in shear reinforcements in the NC model joint caused a decrease in load-carrying capacity by about 26.04%. A shift was also observed in the collapse pattern, i.e., from the beam to the end of the column, causing global failure and reducing the undamaged but increasing more severely damaged condition. This showed that the NC structure, due to the non-conformance of reinforcement, significantly reduced the structure's performance.

With the increasing occurrence of rotator cuff injuries every year, there is a great need for a reliable treatment option. Wharton’s Jelly contains several components that can positively impact the replacement and repair of musculoskeletal defects. The overall objective of this study is to evaluate the improvement of patient-reported pain scales after applying Wharton’s Jelly (WJ) in rotator cuff defects. Eighty-seven patients with rotator cuff defects who failed at least eight weeks of conservative treatment were selected from the retrospective repository. 2cc of WJ flowable allograft was applied to the specific affected anatomy, the most common being supraspinatus tendon, biceps tendon insertion, labral tear, and subscapularis tear. No adverse reactions were reported. Statistically significant improvements were found from the initial to Day 90 in all scales. Patient satisfaction was calculated using minimal clinically important differences. No statistically significant differences were found in mean changes between gender, BMI, and age. Scanning Electron Microscopy images reveal the similarities between the collagen matrix in WJ and the rotator cuff. The significant improvement in patient outcomes coincides with current literature analyzing WJ applications with other structural defects around the body. WJ is a promising alternative for musculoskeletal defects when the standard of care fails.

BackgroundAdvanced radiological stage of knee osteoarthritis (OA) and obesity are predictive of poorer and shorter response to viscosupplementation, but very few is known regarding the impact of other factors such as sport practice, comorbidities or anatomical features of OA. ObjectivesTo investigate the patient’s and OA characteristics associated with the duration of effectiveness (DE) of viscosupplementation in patients with knee OA.MethodsCross-sectional single center trial in patients with knee OA treated with intra-articular (IA) hyaluronic acid (HA) injection(s) within the previous 3 years. The investigator collected demographic and radiographic data (Kellgren grade, involved knee compartments), dosing regimen (single or repeat injections), presence and volume of joint effusion, previous or concomitant IA corticosteroid injection, number of previous viscosupplémentations and the comorbidities. The patient completed a questionnaire including the self-assessment of DE (number of weeks during which viscosupplementation was effective on symptoms), the activity level (sedentary, active, athletic), the level of sport activity (light, moderate or intensive). Predictors of DE were studied in univariate and multivariate analyses ResultsOne hundred five patients (149 knees) were analyzed (62% women, mean age 66.1 ± 13.2 years, mean BMI 27.5 ± 7.5 kg/m²). The mean DE was 48.2 + 24.8 weeks. In a bivariate analysis, the predictors of a shorter with DE were BMI >27.5kg/m2, more than 3 previous viscosupplémentations, Kellgren grade 4, sedentary patients, and more than 1 affected compartment. In the multivariate analysis, 4 independent factors remained associated with a shorter DE: BMI >27.5 kg/m2, knee multi-compartment damage, number of viscosupplements >3, sedentary lifestyle. A statistically significant association between a longer DE and treated arterial hypertension was found suggesting a beneficial effect of certain antihypertensive drugs. ConclusionThe study confirms the harmful influence of an increased BMI, It also shows that viscosupplementation is more effective in unicompartmental OA. Other points worth highlighting are the reduction in the duration of efficacy with repeated cycles of injections and the benefit of a regular physical activity.

Ti17 alloy is mainly used to manufacture aero-engine discs due to its excellent properties such as high strength, toughness and hardenability. It is often subjected to creep-fatigue cyclic loading in service environments. Shakedown theory describes the state in which the accumulated plastic strain of the material stabilizes after several cycles of cyclic loading, without affecting its initial function and leading to failure. This theory includes three behaviors: elastic shakedown, plastic shakedown, and ratcheting. In this paper, the creep-fatigue tests (CF) were conducted on Ti17 alloy at 300℃ to study its shakedown behavior under creep-fatigue cyclic loading. Based on the plasticity-creep superposition model, a theory model that accurately describes the shakedown behavior of Ti17 alloy was constructed, and ABAQUS finite element software was used to validate the accuracy of the model. TEM analysis was performed to observe the micro-mechanisms of shakedown in Ti17 alloy. The results reveal that the Ti17 alloy specimens exhibit plastic shakedown behavior after three cycles of creep-fatigue loading. The established finite element model can effectively predict the plastic shakedown process of Ti17 alloy, with a relative error between the experimental and simulation results within 4%. TEM results reveal that anelastic recovery controlled by dislocation bending and back stress hardening caused by inhomogeneous deformation are the main mechanisms for the plastic shakedown behavior of Ti17 alloy.

In vivo, articular cartilage tissue is surrounded by a cartilage membrane, and HP (HP) and compressive strain increases simultaneously with the compressive stress. However, it has been impossible to investigate the effects of simultaneous loading in vitro. In this study, a bioreactor capable of applying compressive stress under HP was developed to reproduce ex vivo the same physical loading environment found in cartilage in vivo. First, a HP stimulation unit was constructed to apply cyclic HP pressure-resistant chamber by controlling a pump and valve. A compression-loading mechanism that can apply compressive stress using an electromagnetic force was implemented in the chamber. The synchronization between the compression and HP units were evaluated and the stimulation parameters were quantitatively evaluated. Physiological HP and compressive strain were applied to the chondrocytes encapsulated in alginate and gelatin gels after applying high HP at 25 MPa, which induced damage to chondrocytes. It was found that compressive stimulation increased the expression of genes related to osteoarthritis. Furthermore, the simultaneous application of compressive strain and HP, which is similar to the physiological environment in cartilage, had an inhibitory effect on the expression of genes related to osteoarthritis. HP alone also suppressed the expression of osteoarthritis-related genes. Therefore, the simultaneous hydrostatic and compressive stress-loading device developed to simulate the mechanical environment in vivo may be an important tool for elucidating the mechanisms of disease onset and homeostasis in the cartilage.

Fixed offshore wind turbines continue to be developed for high latitude areas where not only wind and wave loads need to be considered, but also moving sea ice. Current rules and regulations for the design of fixed offshore structures in ice-covered waters do not adequately consider effects of ice loading and its stochastic nature on fatigue life of the structure. Ice crushing on such structures results in ice-induced vibrations, which can be represented by loading the structure using a variable-amplitude loading (VAL) sequence. Typical offshore load spectra are developed for wave and wind loading. Thus, a combined VAL spectrum is developed for wind, wave, and ice action. To this goal, numerical models are used to simulate the dynamic ice-, wind-, and wave-structure interaction. The stress time-history at an exemplarily selected critical point in an offshore wind energy monopile support structure is extracted from the model and translated into a VAL sequence, which can then be used as a loading sequence for the fatigue assessment or fatigue testing of welded joints of offshore wind turbine support structures. This study presents the approach to determine combined load spectra and standardized time series for wind, wave, and ice action.

Mycobacterium tuberculosis was responsible for 1.3 million deaths worldwide in 2022. Bacillus Calmette-Guérin (BCG) is the only licensed vaccine against tuberculosis (TB); however, it has limited protective efficacy in adults. In this study, we constructed a recombinant vaccinia virus expressing Ag85B from M. tuberculosis using a novel attenuated vaccinia virus (KVAC103). We then analyzed the immunogenicity of prime-boost inoculation strategies using recombinant KVAC103 expressing Ag85B (rKVAC85B) compared to BCG. In both the rKVAC85B prime-boost and the BCG prime-rKVAC85B boost inoculation regimens, rKVAC85B induced the generation of specific IgG and the secretion of IFN-γ by immune cells. In vitro analysis of Mycobacterium growth inhibition revealed a comparable immune-mediated pattern of outcomes. Furthermore, bacterial loads in the lungs were significantly lower in mice inoculated with the BCG prime-rKVAC85B boost, than in the BCG-only group following a rechallenge infection with both H37Rv and HN878 strains of M. tuberculosis. These findings collectively suggest that KVAC103, incorporated into a viral vector, is a promising candidate for a novel TB vaccine platform that is effective against multiple TB strains, including H37Rv and HN878, and that rKVAC85B effectively stimulates immune responses against TB infection.

Multiaxial fatigue experiments under asynchronous loadings with four different loading frequency ratios were carried out on 30CrMnSiA steel. The experimental results show that the fatigue life decreases when the axial or torsion frequency increases from 1 to 2, while there is no significant change when the axial or torsion frequency increases from 2 to 4. The surface crack paths are observed and show that cracks initiate on the maximum shear stress amplitude planes, propagate approximately tens of microns, and then turn to propagate along the maximum normal stress planes. The number of secondary cracks increases when the axial or torsion frequency increases. Subsequently, the Bannantine-Socie and Wang-Brown cycle counting methods along with various multiaxial fatigue criteria and Palmgren-Miner’s cumulative damage rule were used for fatigue life prediction. The experimental results are consistent with the fatigue life predicted by the Bannantine-Socie method with the section critical plane criterion for 30CrMnSiA steel under asynchronous loading paths.

Nanotechnology has enabled the development of novel therapeutic strategies such as targeted nanodrug delivery systems, control and stimulus-responsive release mechanisms, and the production of theranostic agents. As a prerequisite for the use of nanoparticles as drug delivery systems, the amount of loaded drug must be precisely quantified, a task for which two approaches are currently used. However, both approaches suffer from the inefficiencies of drug extraction and of the solid-liquid separation process, as well as from dilution errors. This work describes a new, reliable, and simple method for direct drug quantification in polymeric nanoparticles using attenuated total reflection Fourier transform infrared spectroscopy, which can be adapted for a wide variety of drug delivery systems. Silk fibroin nanoparticles and naringenin were used as model polymeric nanoparticle carrier and drug, respectively. The specificity, linearity, detection limit, precision and accuracy of the spectroscopic approach were determined in order to validate the method. A good linear relation was observed within 0.00 to 7.89 % of naringenin relative mass with an R2 of 0.973. The accuracy was determined by the spike and recovery method. Results showed an average 104% recovery. The limit of detection and limit of quantification of the drug loading content were determined to be 0.3 and 1.0 %, respectively. The method's robustness is demonstrated by the notable similarities between the calibrations carried out in two different equipment and institutions.

Metal oxide p-n heterojunction nanofibers (NFs) are among the most promising approaches to enhancing the efficiency of gas sensors. In this paper, we report the preparation of a series of p-NiO-loaded n-ZnO NFs, namely (1 − x) ZnO-xNiO (x = 0.03, 0.05, and 0.1 wt%), for hydrogen gas sensing experiments. Samples were prepared through the electrospinning technique followed by a calcination process. The sensing experiments showed that the sample with 0.05 wt% NiO loading resulted in the highest sensing performance at an optimal sensing temperature of 200 °C. The sensing mechanism is discussed in detail and contributions of the p-n heterojunctions, metallization of ZnO and catalytic effect of NiO on the sensing enhancements of an optimized gas sensor are analyzed. This study demonstrates the possibility of fabricating high-performance H₂ sensors through the optimization of p-type metal oxide loading on the surfaces of n-type metal oxides.

The pervasive presence of atmospheric pollution, particularly polycyclic aromatic hydrocarbons such as 7,12-dimethylbenz(a)anthracene, instigates aberrant cellular and tissue conditions, precipitating oxidative damage and inflammatory cascades conducive to the onset of cancer, notably mammary cancer. Given the hepatic metabolism of 7,12-dimethylbenz(a)anthracene, the imperative of employing natural antioxidants becomes apparent. In this study, we delve into the antioxidant and hepato-protective properties of Pistacia lentiscus against 7,12-dimethylbenz(a)anthracene-induced toxicity, alongside exploring its potential anticancer attributes. Our investigations unveil Pistacia lentiscus's anti-proliferative efficacy against human breast cancer cell lines. Notably, 7,12-dimethylbenz(a)anthracene-intoxication escalates body weight, disrupts lipid profiles, and incites serum oxidative damage. Concurrently, hepatic and renal oxidative stress ensue, accompanied by heightened antioxidant enzyme activity in the 7,12-dimethylbenz(a)anthracene-exposed-group compared to controls (p<0.05). Nonetheless, Pistacia lentiscus co-administration rectifies biochemical imbalances, significantly attenuates oxidative stress aberrations, and augments antioxidant enzyme responses (p<0.05). Importantly, histological analysis evinces Pistacia lentiscus's shielding effect against 7,12-dimethylbenz(a)anthracene induced hepatocyte injury and steatosis. Our findings underscore Pistacia lentiscus's robust anti-proliferative, antioxidant, and hepato-protective capacities, mitigating metabolic disturbances, oxidative stress propagation in liver and kidney functions, and potential histological alterations, thereby impeding 7,12-dimethylbenz(a)anthracene-induced mammary cancer initiation. We posit that Pistacia lentiscus may serve as a prophylactic agent against breast cancer instigated by this carcinogen.

Influenza viruses cause acute respiratory infections responsible for significant mortality and morbidity around the world. Various factors, such as antigenic drift, allow influenza strains to avoid being fully suppressed by seasonal vaccines. This has led to the increased scrutiny of antivirals as treatment and prophylaxis options for seasonal outbreaks and potential pandemics. Unfortunately, many influenza antivirals suffer from a lack of adequate clinical trials, as well as a lack of toxicity data. This is especially true of umifenovir (arbidol), a drug popularly used for the prevention and treatment of influenza strains in China and Russia. Neuraminidase inhibitors, though widely prescribed, display a potential for future resistance. Adamantanes, while proven to be effective in treating influenza A, are already encountering rapid and widespread cross-resistance and are effectively obsolete. Baloxavir marboxil, a newer antiviral, shows promise in treating acute uncomplicated influenza and may avoid the development of resistance when co-administered with other antiviral drugs. Indeed, the low genetic barrier to resistance associated with influenza antivirals could potentially be overcome by co-administration with other antivirals. This review explores the most widely prescribed antivirals for influenza treatment, their mechanisms of action, and the data currently available about their susceptibility to resistance and efficacy.

Background An outbreak of African swine fever (ASF) in China in 2020 has led to an unprecedented shortage of fraxiparin. Most patients, especially those kept in hospital for surgery, are currently treated with prophylactic anticoagulation (AC). In search of alternatives for fraxiparin, we found no sufficient data on alternatives for neurosurgical patients, such as tinzaparin of European origin. We compared fraxiparin and tinzaparin concerning adverse events (bleeding versus thromboembolic events) in neurosurgical patients. Methods Between 2012 and 2018, 517 neurosurgical patients with benign and malignant brain tumors as well as 297 patients with subarachnoid hemorrhage (SAH) were treated in the Department of Neurosurgery, University Hospital Leipzig receiving prophylactic anticoagulation within 48 hours. In 2015, prophylactic anticoagulation was switched from fraxiparin to tinzaparin throughout the university hospital. In a retrospective manner, the frequency and occurrence of adverse events (rebleeding and thromboembolic events) in connection with the substance used was analyzed. Statistical analysis was performed using Fisher’s exact test and the chi-squared test. Results Rebleeding rates were similar in both fraxiparin and tinzaparin cohorts in patients being treated for meningioma, glioma, and SAH combined (8.8 vs 10.3%). Accordingly, the rates of overall thromboembolic events were not significantly different (5.5% vs 4.3%). The severity of rebleeding did not vary. There was no significant difference among subgroups when compared for deep vein thrombosis (DVT) or pulmonary embolism (PE). Conclusion In this retrospective study, tinzaparin seems to be a safe alternative to fraxiparin for AC in patients undergoing brain tumor surgery or suffering from SAH.

Melasma is a challenging skin condition which involves both structural and functional skin alterations. Despite the availability of various treatment options, the management remains complex. This is the first study to investigate topical application of Rosa Damascena stem cell exosomes when used concomitantly with microneedling in women and men with facial melasma. We recruited 20 subjects with Fitzpatrick skin types I-III, exhibiting melasma of varying severity. The modified Melasma Area and Severity Index (mMASI) and Global Aesthetic Improvement Scale (GAIS) were utilized to evaluate treatment response. The treatment protocol involved microneedling followed by exosome application over four or five sessions, at 4-week intervals. Ninety percent of subjects demonstrated a significant improvement in mMASI scores, while only 10% showed no change. GAIS assessment further supports overall improvement, with just 10% categorized as "not changed". Tolerability was favorable, with mild, transient side effects. Our findings suggest promising outcomes with this combined therapy, underscoring its potential as a safe and effective approach for treating melasma, particularly in severe and moderate cases. However, further research with larger sample sizes and control arms is warranted to validate these findings and explore long-term efficacy.

This study determines the equivalent stress intensity factor (SIF) model that best fits the experimental behavior of low-carbon steel under mixed mode (I and II). The study assessed Tanaka, Richard, and Pook's equivalent SIF models. The theoretical values used for comparison correspond to experimental results in a modified C(T) geometry by machining a hole ahead of the crack tip subjected to fatigue loads with a load ratio of R = 0.1. The comparison involved the SIF for six experimental points and the values computed through the numerical simulation. The Paris, Klesnil, and modified Forman-Newman crack growth models were used with each equivalent SIF to analyze the prediction in the estimated number of cycles. The Klesnil model showed the closest prediction since the error between the calculated and experimentally recorded number of cycles is the lowest. However, the material behavior reflects a reduced crack propagation rate attributed to plasticity in the crack tip. Results suggest that Asaro equivalent SIF conservatively estimates the element lifespan with increasing errors from 2.3% at the start of growth to 27 % at the end of the calculation.

Postmenopausal osteoporosis, a metabolic bone disease associated with aging and that affects bones throughout the body, is emerging as an urgent public health concern and imposes a substantial healthcare burden on society. The clinical application of bisphosphonate, the primary treatment for osteoporosis, is limited owing to the drug’s severe complications. Herein, we investigate the synthesis and utilization of strontium-doped mesoporous bioactive glass loaded with alendronate (ALN@Sr-MBG) as a novel therapeutic agent for osteoporosis, to explore its potential as an alternative to alendronate (ALN). Strontium-doped mesoporous bioactive glass (Sr-MBG) was synthesized using the sol-gel method, while ALN@Sr-MBG was obtained by incorporating Sr-MBG into an alendronate saturated solution. The bioactivities of ALN@Sr-MBG, including biotoxicity, inflammation inhibition, and anti-osteoclast differentiation, were investigated in vitro using CCK-8, flow cytometry, tartrate-resistant acid phosphatase (TRAP) staining, and RT-PCR assays. Animal models were established by surgically removing the ovaries from non-pregnant female C57/BL mice, followed by weekly intraperitoneal injections of ALN@Sr-MBG, ALN, or excipients. After 8 weeks, the mice femurs were extracted and analyzed through Micro-CT scanning, and hematoxylin-eosi, osteoblastic, and osteogenic staining. The in vitro findings demonstrated that ALN@Sr-MBG displayed enhanced biological efficacy compared to ALN in terms of inflammation inhibition, osteogenesis promotion, and osteoclastogenesis inhibition. Furthermore, micro-CT analysis revealed that ALN@Sr-MBG significantly augmented bone mineral density (BMD), bone volume fraction (BV/TV), trabecular number (Tb.N), and trabecular thickness (Tb.Th), while reducing trabecular separation (Tb.Sp) and structural model index (SMI) in mice with ovariectomy-induced osteoporosis. The osteoblast and osteogenic staining results indicate the enhanced bioactivities of ALN@Sr-MBG in promoting bone formation and inhibiting bone resorption compared to ALN. In vitro and in vivo assessments further confirmed that ALN@Sr-MBG exhibits superior anti-osteoporotic bioactivity compared to ALN. The study findings confirm the potential of ALN@Sr-MBG as a novel alternative therapy to ALN and drug candidate for the treatment of osteoporosis.

A drug repositioning effort supported the possible use of the anti-HIV drug etravirine as a treatment for Friedreich Ataxia (FRDA). Etravirine increases frataxin protein and corrects the biochemical defects in cells derived from FRDA patients. Because of these findings, and since etravirine displays a favorable safety profile, we conducted this pilot open-label phase 2 clinical trial assessing the safety and potential efficacy of etravirine in FRDA patients. Thirty-five patients were stratified into 3 severity groups and randomized to etravirine 200 mg/day or 400 mg/day. They were treated for 4 months. Efficacy endpoints were represented by changes in peak oxygen uptake and workload as measured by incremental exercise test, SARA score, cardiac measures, measures of QoL and disability. Data were collected 4 months before the start of the treatment (T-4), at the start (T0), at the end (T4) and 4 months after the termination of the treatment (T+4). Etravirine was well tolerated. Etravirine completely stopped the progression of the SARA score during the 4-months treatment period, compared to the 4 months pre and post treatment. It increased peak workload, while the improvement of peak oxygen uptake was not statistically significant. No changes in the cardiac measures were observed. Health and QoL measures showed a worsening at the suspension of the drug. In this open trial etravirine significantly improved neurological function and was generally safe and reasonably tolerated. This suggests that etravirine represents a potential therapeutic agent in FRDA deserving testing in a randomized placebo controlled clinical trial.

A simulation test system for the two-dimensional (2D) fuze overload loading process was designed to address the loading issues of recoil overload and centrifugal overload in fuze safety and arming (S&A) devices. By incorporating centrifuge rotation energy storage, impact acceleration simulation, and equivalent centrifugal rotation simulation, a block equipped with a fuze S&A device was accelerated instantly upon being impacted by a centrifuge-driven impact hammer, simulating recoil overload loading. The impact hammer was retracted instantaneously by adopting an electromagnetic brake, which resulted in the centrifugal rotation of the block around its track, to simulate the centrifugal overload loading. The dynamic equations of the simulation test system and the equations of impact hammer motions were established, whereby the rotation speed of the centrifuge and the braking force of the electromagnetic brake were calculated and selected. A dynamic model of the collision between the impact hammer and block was established using ANSYS/LS-DYNA software for simulation analysis. The acceleration curves of the recoil overload and centrifugal overload with variations in the centrifuge speed, cushion material, and buffer thickness were obtained, which verified the feasibility of the proposed loading simulation method. 2D overload loading simulation tests were performed using the developed simulation system, and the acceleration curves of the recoil overload and centrifugal overload were measured. The test results indicated that the proposed system can accomplish 2D overload loading simulations for a recoil overload of several 10000 g and centrifugal overload of several 1000 g.

Mutations in epidermal growth factor receptor (EGFR) occur in about 48% of Asian and 19% of Western patients with lung adenocarcinoma (LUAD), leading to its constitutive activation and subsequent uncontrolled cell proliferation. To counteract this, tyrosine kinase inhibitors (TKIs) have been developed, targeting EGFR activity. However, the emergence of metastases and resistance mutations often undermines the durability of the treatment response. Knowledge-based mechanistic models that replicate existing clinical trial outcomes, tailored to specific population characteristics, provide invaluable assistance in designing future clinical trials. These models are particularly effective in identifying optimal responders to specific treatments, thereby enhancing therapeutic efficacy. We have developed physiologically based pharmacokinetic (PBPK) models for gefitinib and osimertinib, representing two distinct generations of EGFR TKIs, to accurately simulate the drugs’ distribution within the primary tumor and metastatic sites following oral administration. These models were integrated with a pathophysiological mechanistic model of EGFR-mutant LUAD, enabling the representation of the effects of both gefitinib and osimertinib on EGFR activation-induced signaling pathways. This comprehensive model outputs detailed evolutions of the primary tumor and each metastatic site, facilitating the evaluation of patient progression in alignment with RECIST guidelines (version 1.1). Notably, the model encapsulates the heterogeneity within the tumor, through the representation of various subclones, each characterized by unique mutation profiles, thereby reflecting differential responses to treatment. Calibration of the model was achieved using publicly available data from the NEJ002 and FLAURA clinical trials. Rigorous visual predictive checks and statistical tests were employed to ensure the proper behavior of the model. The model adeptly replicated the time to progression observed in real clinical trials in EGFR-mutant LUAD patients receiving gefitinib or osimertinib as first-line therapy. In addition, the model was able to reproduce the results from a retrospective study comparing gefitinib and osimertinib, a study that was not used to inform the model. With a consistent virtual population as a reference, the combined model facilitated a comparative analysis of the efficacy of both treatments, thereby underscoring its utility in evaluating therapeutic strategies. The faithful replication of real-world data significantly enhances the credibility of our model, rendering it a vital investigational tool for deriving pertinent insights and informing treatment strategies, particularly in identifying optimal responders to various generations of EGFR TKIs. Following its consecutive prospective validations in the FLAURA2 and MARIPOSA trials, the model is poised to facilitate the generation of synthetic control arms in future clinical trials. This advancement promises a more nuanced analysis of covariate relationships, especially when comparing investigational treatments to established standards of care. Additionally, it potentially reduces the required patient cohort size in such trials, optimizing resource utilization.

Background: To investigate the safety and efficacy of palliative arterial embolization for metastases of the scapula. Materials and Methods: We studied the files of the patients who underwent palliatrive arterial embolization for metastases of the scapula from January 2016 to January 2023, 15 patients (8 M, and 7 F) with a mean age of 62 years (SD 10.2) with two patients receiving a second procedure, for a total of 17 embolizations. Data on technical and clinical success, as well as changes in tumor size, were collected. All embolization-related complications were evaluated according to the CIRSE classification system for complications. Results: The average follow-up was 18 months (Range 6-36 months). The main primary tumor were renal, lung and breast cancer. The primary arteries embolized were the circumflex scapular artery, the dorsal scapular artery, and the thoracoacromial trunk. A mixture of Glubran and Lipiodol in a 1:2 ratio was used for embolization, with an average of 1.1 mL (Range 0.5-1.5 mL) used per procedure. The efficacy of embolization was measured using the Visual Analogue Scale (VAS), with values recorded at baseline, at 1, 3, 6, and 12 months post-embolization, and at 6-month intervals after. Baseline VAS scores averaged 7.2 (SD 1.5), decreasing to 2.8 (SD 0.9) at one month. Progressive reduction was observed at 3, 6, and 12 months with scores of 2.3 (SD 0.8), 1.9 (SD 0.7), and 1.6 (SD 0.6) respectively. Metastatic tumor size was reduced from a mean of 192.2 cm3 (range 38.7 to 480.1 cm3) pre-embolization to a mean of 177.3 cm3 (range 37.2 to 455.5 cm3) at the 12-month follow-up (p

Hymenoptera allergens are the main triggers for anaphylaxis in susceptible dogs and humans. Hymenoptera venom specific immunotherapy (VIT), the only disease-modifying treatment, has the potential to prevent future life-threatening reactions in human patients. Prospective clinical data on VIT efficacy in dogs are currently lacking. Therefore, the aim of this study was to show that VIT is not only safe but also efficacious in preventing anaphylaxis in dogs allergic to Hymenoptera. This uncontrolled prospective clinical trial included 10 client-owned dogs with a history of anaphylaxis following repeated Hymenoptera stings. The sensitization to bee and wasp allergens was demonstrated by intradermal testing (IDT) and allergen-specific IgE serology. For VIT induction (induction phase), dogs received a shortened rush immunotherapy protocol with aqueous allergens, which was then followed by monthly injections of 100 g of alum-precipitated allergen (maintenance phase). VIT efficacy was determined by observing patients’ clinical reactions to re-stings. No systemic adverse events were seen during the induction and maintenance phase. From the seven re-stung dogs, only one developed a mild angioedema at the site of the sting; the remaining dogs were asymptomatic. These results show that VIT represents a safe and effective treatment option for Hymenoptera-allergic dogs.

Steel fibre reinforced concrete (SFRC) consists of short hooked steel fibres randomly distributed and oriented within the cementitious matrix. The contribution of fibre in bridging cracks to provide the stress transfer required relies upon the orientation of the fibre in the concrete. Bridging fibre aligned with a crack are less effective than those inclined to it. Therefore, understanding the pull-out behaviour of misaligned fibre is a key factor to quantify and optimize the design of SFRC in the structural applications. In the laboratory a single oriented fibre embedded in a solid cylinder of concrete is subjected to a pull-out test where the axis of a tensile force is aligned with the axis of the cylinder. Based upon the observed behaviour this paper presents a new analytical bounding approach to capture the pull-out response of misaligned hooked-end steel fibre embedded in a concrete matrix. The analysis is based upon a transversely isotropic condition assumed for the plasticity that occurs in the cold drawn fibre. The model accounts for the influence of fibre diameter and the combined strengths of the steel and concrete. The model predictions have also been compared with other experimental results published in the literature. The results showed that the model can predict pull-out loads reasonably for different fibre orientations between bounds of failure derived from the strengths of the two constituents. A critical orientation is observed at maximum strength. Therein, an understanding of the pull-out behaviour of misaligned, hooked-end fibres is necessary to optimize the strength of concrete from this method of reinforcement.

Numerous study reports on chitosan hydrogels in different forms such as films, porous structures, nanoparticles, and microspheres for biomedical applications, however, this study concentrates on their modifications with different crosslinking agents and observing their effects on drug loading and releasing capacities. Linear chitosan along with crosslinked by two major cross-linkers, i.e., genipin and disulfide have been used to formulate three different hydrogel systems. The cross-linking process is heavily impacted by the temperature and the pH conditions. Three different drugs, i.e., thymoquinone, gefitinib, and erlotinib are loaded in phosphate buffer solutions and infused with three different hydrogel systems, thus, a total of nine combinations are studied and analyzed for drug loading and releasing capabilities with Ultraviolet–visible (UV-Vis) spectroscopy. This study finds thymoquinone shows the lowest loading efficacy compared to two other drugs in all three systems. Gefitinib shows stable loading and releasing regardless of crosslinking systems and genipin crosslinked system shows stable loading and releasing with all three drug molecules. These experimental results agree well with the findings of our previously published results conducted with molecular dynamics simulations.

The practical application of a pH-responsive Nanoparticle Drug Delivery System (NDDS) in cancer treatment is often hampered by several issues such as the protection of therapeutic molecules from external stresses, inefficient targeted delivery, sustained drug release, and poor efficacy. This study presents an effective design strategy for the synthesis of a pH-sensitive controlled hydrophobic drug delivery method based on the formulation of chitosan (CS)-coated mesoporous silica nanoparticles (MSNs) through the sol-gel method, where hydrolysis takes place in the acidic medium followed by polycondensation of the hydrolyzed products. For this purpose, NH2 modified-MSNs were prepared by using tetraethyl orthosilicate (TEOS) as precursor and cetyltrimethylammonium bromide (CTAB) as a template, and 3-aminopropyltriethoxysilane (APTES) for amine modification, followed by hydrophobic drug loading and CS coating of various concentrations. Camptothecin (CPT) was used as a model drug. Fabricated monodispersed functionalized nanoparticles had sizes ranging from 200nm to 245nm with an encapsulation efficiency as high as 90%. The highest encapsulation efficiency was found for 1% CS coating, which released 50% drug in 120h at pH 6.4 and 20% at pH 7.4 respectively. These nanoformulations exhibited pH-responsive release patterns of CPT under two different pH values (pH=7.4 and pH=6.4). These results contribute to the optimization of NDDS, with potential implications for nanoformulations designed for controlled and sustained drug release particularly to tumors without affecting healthy cells owing to differences in the pH of the tumor microenvironment and the normal physiological environment of cells.

Drug delivery through Liposomes has shown tremendous potential in terms of the therapeutic application of nanoparticles. There are several drug-loaded liposomal formulations approved for clinical use that help mitigate harmful effects of life-threatening diseases. Developments in the field of liposomal formulations and drug delivery have made it possible for clinicians and researchers to find therapeutic solutions for complicated medical conditions. A key aspect in the development of drug-loaded liposomes is a careful review of optimization techniques to improve the overall formulation stability and efficacy. Optimization studies help in improving/modulating the various properties of drug-loaded liposomes and are vital for the development of this class of delivery systems. A comprehensive overview of the various process variables and factors involved in the optimization of drug-loaded liposomes is presented in this review. The influence of different independent variables on drug release and loading properties with the application of a statistical experimental design is also explained in this article.

Polymethyl methacrylate (PMMA) polymer is widely used in various fields today. In order to thoroughly reveal the structural impact performance of PMMA materials, this paper is based on the comprehensive Johnson-Cook constitutive model and damage failure model, and accurately confirm the J-C constitutive and damage failure model parameters of PMMA through material test data, The dynamic process of steel bullet impacting PMMA plate structure is analyzed by finite element software ABAQUS. The calculation results show that the numerical simulation results in this paper are in good agreement with the experimental test data. Therefore, the feasibility and accuracy of the impact analysis of PMMA structures based on J-C constitutive and damage failure models in this paper are studied. Finally, based on the J-C constitutive model and damage failure model, the variation of the residual velocity of the bullet with the PMMA plate thickness is analyzed in depth, that is, the results show that the residual velocity of the bullet has a certain linear relationship with the plate thickness.

The control of stereo-, regio-, and chemo-selectivity in transition-metal-catalyzed coupling reactions is a key topic in organic synthesis. Several methods for controlling selectivity have been reported thus far. On the other hand, the reduction of the catalyst loading in the reaction is one of the most important issues in organic synthesis from the standpoint of green sustainable chemistry. As another advantage of reducing the catalyst loading, the expression of the reaction selectivity and the substituent effect caused by the reduction of the catalyst loading to the parts-par-million (ppm) level in various catalytic reactions is presented herein.

The Hertzian contact theory, as well as most of the other classical theories of normal and tangential contact, provides displacements and the distribution of normal and tangential stress components directly in the contact surface. However, other components of the full stress tensor in the material may essentially influence the material behaviour in contact. Of particular interest are principal stresses and the equivalent von Mises stress, as well as the gradient of the hydrostatic pressure. For many engineering and biomechanical problems, it would be important to find these stress characteristics at least in the contact plane. In the present paper, we show that the complete stress state in the contact plane can be easily found for axially symmetric contacts under very general assumptions. We provide simple explicit equations for all stress components and the normal component of the gradient of hydrostatic pressure in the form of one-dimensional integrals.

Recent advances in embedded antenna and sensor technologies for 5G communications have galvanized a response toward the investigation of their electromagnetic (EM) performance for urban context and civil engineering applications. This article quantitatively investigates the effects of material loading on an evolved antecedent-based design of a hexagonal-stubbed Complementary Split-Ring Resonator (CSRR)-loaded antenna through simulation and experimentation. The optimized antenna design is first conceptualized within a simulation environment to achieve EM resonance at 3.50 GHz before delving into the analysis of operational performance characteristics. As a proof-of-concept, a physical antenna prototype is fabricated on a printed circuit board for the in-situ evaluation of S11 parameter plot. Subsequently, a simulation-based parametric study is conducted on antenna prototypes embedded into Ordinary Portland Cement pastes with varying weight percentages of iron(III) oxide. Simulation-derived and experimental results are mutually verified, achieving a systemic downward shift in resonant frequency and corresponding variations in impedance matching induced by changes in the loading reactance. Finally, an inversion modeling procedure is employed using perturbation theory to extrapolate the relative permittivity of the dielectric embedding materials. Our proposed analysis contributes to optimizing concrete-embedded 5G antenna sensor designs and establishes a foundational framework for estimating unknown EM parameters of cement-based composites.

A reliable finite element procedure to simulate shear-dominated ductile fracture in large-scale, thin-walled steel structures is still evolving due primarily to the challenges in determining the fracture criterion of steel materials under complex stress states. This paper aims to examine the accuracy of the modified Gurson-Tvergaard-Needleman (GTN) model considering the shear failure in simulating ductile fracture of steel plate structures under quasi-static punch loading. The modified GTN damage models are performed by ABAQUS user defined material subroutine (VUMAT). The void related parameters and shear damage parameters of Xue’s and N-H modified GTN models are calibrated from test specimens with various geometries corresponding to different stress triaxiality and shearing conditions. The damage evolution associated with the shearing of voids in the modified GTN models has strong influences on the stress triaxiality versus equivalent plastic strain under complex stress states, especially for the shear dominated loading conditions. Based on the original GTN model, Xue’s model, and N-H modified GTN model with calibrated material parameters, a numerical comparative study examines the ductile fracture of steel non-stiffened plate and stiffened plate under punch loading. Benchmarked against the experimental studies, the numerical simulations demonstrate that the shear driven void evolution in the modified GTN model imposes significant effects on the load-displacement responses, as well as the onset and extension of ductile fracture in steel plates under punch actions. The N-H modified model with calibrated shear damage parameters shows a better correlation with the ductile fractures in steel plates observed in the experiment, than the original GTN model and Xue’s modified GTN model. As a result of this study, the modified GTN model considering the shear failure can be applied for practical applications in the crashworthiness assessment of ship collision and grounding.

Greenwater (splashing of water on the deck) loading is a classical problem faced by the designer of ship-shaped vessels, which becomes even worst when the vessel operates at harsh weather conditions for an extended period. Installation of breakwaters on the deck can play a crucial role in minimizing this impact. However, research on the design and optimization of the breakwater is still at its infancy, and this study aims at shedding further light on this area by proposing and analyzing the effectiveness of three breakwater designs on a fixed box-shaped vessel. Commercial CFD software is used for this investigation. However, the design model (without breakwater) was validated at first against experimental results of green water splashing, before performing the actual simulations with proposed breakwater design. A vertical plate is used as the deck structure, and greenwater pressure at several locations on that plate is measured to compare the effectiveness of various breakwater designs. Overall, breakwaters with openings (perforations, grillages etc.) found to be more effective in minimizing the pressure generated by the greenwater. Nevertheless, there are significant rooms for improvement on breakwater designs, and some topics for further research are also suggested in this regard.

The use of new developed high-strength steel in concrete members can reduce steel bars congestion and construction costs. This research aims to study the behavior of concrete columns reinforced with new developed high-strength steel under eccentric loading. Ten reinforced concrete columns were fabricated and tested. The test variables are transverse reinforcement amount and yield strength, eccentricity, and longitudinal reinforcement yield strength. The failure patterns are compression and tensile failure for columns subjected to small eccentricity and large eccentricity, respectively. The same level of post-peak deformability and ductility only can be obtained with lower amount of transverse reinforcement when high-strength transverse reinforcements are used in columns subjected to small eccentricity. The high-strength longitudinal reinforcement can improve bearing capacity and post-peak deformability of concrete columns. Besides, three different equivalent rectangular stress block (ERSB) parameters in predicting bearing capacity of columns with high-strength steel were discussed based on test and simulated results. It is concluded that the Code of GB 50010-2010 overestimates the bearing capacity of columns with high-strength steel, whereas bearing capacities computed using Codes of ACI 318-14 and CSA A23.3-04 agree well with test results.

Multilayered metallic sheets fabricated by hot metal forming processes are attractive structural components in the aerospace and automobile industry. The strength of the mechanical bond between the different layers is critical to the applicability of such components in load bearing applications. While it is well understood that the process conditions such as temperature, deformation and rate of deformation influence the bond strength, a clear functional relationship between these conditions and the bond strength has yet to be established. The objective of the current study is to investigate the joining of Aluminum-6061 alloy specimens by hot compression bonding. Hot compression tests of beam specimen pairs were conducted at different temperatures (300-500℃), with different strains and strain rates (10-2-10-1 [1sec]). Coupled thermo-mechanical finite element models were utilized to compute the time dependent thermo-mechanical fields that develop along the specimen interface. The computed values were used to map the spatial distribution of a scalar parameter J which is hypothesized to govern bond formation. Mechanical tensile tests were used to determine the bond strength and expose the bonded surfaces. It is demonstrated that the computed J distribution can be correlated well with SEM observations of the debonded surface. It is also shown that the actual bonded area can be predicted from the computations for a certain range of critical J values.

Curcumin, a nontoxic and cheap natural medicine, has high therapeutic efficacy for many diseases including diabetes and cancers. Unfortunately, its exceedingly low water-solubility and rapid degradation in the body severely limit its bioavailability. In this work, we prepare a series of biocompatible poly(vinyl anisole)@nonlinear poly(ethylene glycol) (PVAS@PEG) core-shell nanogels with different PEG gel shell thickness to provide high water solubility, good stability, and controllable sustained release of curcumin. The PVAS nanogel core is designed to attract and store curcumin molecules for high drug loading capacity and the hydrophilic nonlinear PEG gel shell is designed to offer water dispersibility and thermo-responsive drug release. The obtained nanogels are monodispersed in spherical shape with clear core-shell morphology. The size and shell thickness of the nanogels can be easily controlled by changing the core-shell precursor feeding ratios. The optimized PVAS@PEG nanogels display a high curcumin loading capacity of 38.0 wt%. The nanogels can stabilize the curcumin from degradation at pH =7.4 and release the curcumin in response to heat in the physiologically important temperature range. The nanogels can enter cells effectively and exhibit negligible cytotoxicity to both the B16F10 and HL-7702 cells at a concentration up to 2.3 mg/mL. Such designed PVAS@PEG nanogels have a great potential to be used for delicate drug delivery.

This paper presents the design and implementation of a remote supervision and control system for a gunpowder drum filling plant. The use of technologies such as SCADA (Ignition), IoT (Node-RED), ERP (Odoo) and digital twins (Factory I/O) to achieve remote monitoring and operation of the plant is described. The solution allows full control of the production process from any location through customized graphical interfaces. The challenges encountered in integrating multiple systems and platforms are discussed, along with the security measures implemented within the Azure cloud environment. The results demonstrate the effectiveness of 4.0 technologies in automating and digitizing critical industrial processes. This research will lay the groundwork for the adoption of these approaches in companies seeking greater efficiency, traceability and safety in their operations. The experience gained allows us to successfully face the digital transformation in modern manufacturing.

The rehabilitation of the road embankments alongside the irrigation canal, which is constructed on a Bangkok soft clay foundation, has resulted from land use growth for several decades. As a result, the embankment is always confronted with the problem of instability. Numerous articles have demonstrated that rapid drawdown of the water level in the canal could be one of the most significant reasons, whereas vehicle cyclic loading may potentially contribute to some effect of the embankment failure. To explore and assess the effects of the influence factors, the finite element method (FEM) and conventional and dynamic triaxial approaches were employed. The study also investigated the consequences of varying thicknesses of soft clay and cyclic loading with different magnitudes and frequencies. Consequently, cyclic loading can lead to an augmentation in strain distribution and excess pore water pressure. Likewise, more significant deformation and excess pore water pressure were induced by a lower frequency and deeper thickness of soft clay compared to a higher frequency and thinner thickness. In brief, vehicle repetitive loading is one of the primary factors contributing to embankment failure, with the threshold stress being approximately three-fourths of the undrained shear strength. In contrast, threshold strain is approximately one to two-fold of the monotonic strain condition.

Increasing the loading density of nanoparticles on carbon support is essential for making Pt-alloy/C catalysts practical in H2-air fuel cells. The challenge lies in increasing the load-ing while suppressing the sintering of Pt-alloy nanoparticles. This work presents a 40% Pt-weighted sub-3 nm PtCo/C alloy catalysts via a simple incipient wetness impregnation method. By carefully optimizing the synthetic conditions such as Pt/Co ratios, calcination temperature and time, the size of supported PtCo alloy nanoparticles is successfully con-trolled below 3 nm, and a high electrochemical surface area achieves of 94 m2/g is achieved, which is 2.8 times of commercial PtCo/C-TKK catalysts. Demonstrated by elec-trochemical oxygen reduction reaction, PtCo/C alloy catalysts present an enhanced mass activity of 0.45 A/mg at 0.9 V vs. RHE, which is 1.7 times that of PtCo/C-TKK catalyst. Therefore, the developed PtCo/C alloy catalyst can potentially be a highly practical cata-lyst for H2-air fuel cells.

To quantify damage to reinforced concrete (RC) column members after an earthquake, an engineer needs to know the maximum applied force that was generated by the earthquake. Therefore, in this work, piezoceramic transducers are used to detect the applied force on an RC column member under dynamic loading. To investigate the use of post-embedded piezoceramic sensors in detecting the force that is applied to RC columns, eight full-size RC column specimens with various failure modes are tested under specific earthquake loadings. Post-embedded piezoceramic sensors are installed at a range of depths (70-80 mm) beneath the surface of a column specimen to examine the relationship between the signals that are obtained from them and the force applied by the dynamic actuator. The signals that are generated by the post-embedded piezoceramic sensors, which correlate with the applied force, are presented. These results indicate that the post-embedded piezoceramic sensors have great potential as tools for measuring the maximum applied force on an RC column in an earthquake. Restated, signals that are obtained from post-embedded piezoceramic sensors on an RC column in an earthquake can be used to determine the applied force and corresponding damage or residual seismic capacity.

A framework of similarity laws, termed oriented-density-length-velocity (ODLV) framework, is suggested for the geometric distorted structures subjected to impact loading. The distinct feature of this framework is that the newly proposed oriented dimensions, dimensionless numbers and scaling factors for physical quantity are explicitly expressed by the characteristic lengths of three spatial directions, which overcome the inherent defects that traditional scalar dimensional analysis could not express the effects of structural geometric characteristics and spatial directions for similarity. The non-scalabilities of geometrical distortion as well as other distortions such as different materials and gravity could be compensated by the reasonable correction for the impact velocity, the geometrical thickness and the density, when the proposed dimensionless number of equivalent stress is used between scaled model and prototype. Three analytical models of beam, plate and shell subjected to impact mass or impulsive velocity are verified by equation analysis. And a numerical model of circular plate subjected to dynamic pressure pulse is verified in more detail, form the view of point of space deformation, deformation history and the components of displacement, strain and stress. The results show that the proposed dimensionless numbers have attractively perfect ability to express the dimensionless response equations of displacement, angle, time, strain and strain rate. When the proposed dimensionless numbers are used to regularize impact models, the structural responses of the geometrically distorted scaled models can behave the completely identical behaviors with those of the prototype on space and time —not only for the direction-independent equivalent stress, strain and strain rate but also for the direction-dependent displacement, stress and strain components.

In this work 144 reinforcing bars of high-ductility steel named B500SD were subjected to an accelerated corrosion treatment and then tested under tension at different loading speeds in order to assess the effect of corrosion on the ductility properties of the rebars. Results showed that the bars with a corrosion level as low as the one reducing the steel mass by 1% gave rise to a significant degradation on the ductility properties with strain-stress curves losing the yield plateau and behaving practically as cold deformed steel bars. This effect took place at every tested loading speed. Thus, the research significance relies on the assessment of the influence of the loading speed at which the tensile test is performed given that it affects the ductility properties of the reinforcement bars.

Airworthiness certification requires proof of structure strength, which is performed generally through building block approach. To achieve this, representative intermediate scale experiments generated by test benches are in general needed, additionally to material characterization at coupons scale and structure testing at large scale. The VERTEX test bench can generate combined loading of tension/compression-shear-pressure on structural elements and was modelled with Finite Elements to perform virtual testing representative of its intermediate-scale specificity. The numerous bolted joints of the bench were modelled and their behavior identified in previous tests, so the model could quantitatively estimate the transfer function of the bench, which is the relation between the displacements imposed by the jacks and the resulting loads on a given sample. The VERTEX model was identified to represent load shapes and amplitudes on a training set, and was later confronted to a validation set of tests of tension and shear. A model with ideal boundary conditions was also developed for comparison but it failed to predict some load shape specificities and did not give any indication of loading amplitude. Application cases of the developed model are shown to assess a range of virtual testing possibilities.

The ductile behavior of strain hardening cement-based composites (SHCC) under direct tensile load makes them promising solutions for applications where high energy dissipation is needed, such as earthquake, impact by a projectile, or blast. However, the superior tensile ductility of SHCC due to multiple cracking does not necessarily entail compressive and shear ductility. As an effort to characterize the behavior of SHCC under impact compressive and shear loading, relevant to the mentioned high-speed loading scenarios, the paper at hand studies the performance of a SHCC and its constituent cement-based matrices using the split-Hopkinson bar method. For compression experiments, cylindrical specimens with a length-to-diameter ratio (l/d) of 1.6 were used. The selected length of the sample led to similar failure modes under the quasi-static and impact loading conditions, which was necessary for a reliable comparison of the obtained compressive strengths. The impact experiments were performed in a split-Hopkinson pressure bar (SHPB) at a strain rate that reached 110 s-1 at the moment of failure. For shear experiments, a special adapter was developed for a split-Hopkinson tension bar (SHTB). The adapter enabled performing impact shear experiments on planar specimens using the tensile wave generated in the SHTB. Results showed a dynamic increase factor (DIF) of 2.3 and 2.0 for compressive and shear strength of SHCC, respectively. As compared to the non-reinforced constituent matrix, the absolute value of the compressive strength was lower for the SHCC. Contrarily, under shear loading, the SHCC yielded the higher shear strength than the non-reinforced matrix.

Abstract: Background: epileptic encephalopathies (EE) are characterized by severe drug-resistant seizures, early-onset, and unfavorable developmental outcome. We describe a cohort of pediatric patients with EE who underwent intravenous methylprednisolone (IVMP) pulse therapy to examine its efficacy/tolerability. Methods: This is a retrospective study from 2020 to 2023. Inclusion criteria were: ≤18 years at the time of IVMP pulse therapy and at least 6 months of follow-up. Efficacy and outcome, defined as seizure reduction >50% (responder rate), were evaluated at 6 and 9 months of therapy, and 6 months after therapy suspension; quality of Life (QoL) was also assessed. Variables predicting positive post-IVMP outcomes were identified using statistical analysis. Results: Twenty-one patients were included. The responding rate was 85.7% at 6 and 9 months of therapy, and 80.9% at 6 months after therapy suspension. Genetic etiology and encephalopathy related to status epilepticus during NREM sleep (ESES) were predictive of efficacy (p=0.0475). The fourth month of therapy was the minimum time point to establish the effectiveness of the treatment. All patients showed improvements in QoL, EEG tracing and postural-motor development. No relevant adverse events were observed. Conclusions: Our study confirms the efficacy and tolerability of pulse IVMP treatment in pediatric patients with EE, especially with genetic etiology and ESES. The fourth month of therapy was the minimum time point to establish its effectiveness. QoL, EEG and postural-motor development also showed improvement.

Self-efficacy and perfectionism play an important role in high-performance activities. This cross-sectional study analyses the relationship between these constructs and resilience in a sample of 145 music students (57.9% female) with a mean age of 27.77 years. Perfectionism was assessed using the Multidimensional Inventory of Perfectionism in Sport, resilience using the Resilience Scale, and self-efficacy using the General Self-Efficacy Scale. Compared to those with low resilience, students with high resilience score higher on self-efficacy and lower on dysfunctional perfectionism. No differences were observed in the total perfectionism score or adaptive perfectionism. Self-efficacy shows significant predictive power for resilience (β = .525, p < .001). Although functional perfectionism did not significantly predict resilience, a marginal negative relationship was found between dysfunctional perfectionism and resilience (β = - .156, p = .063). The results are discussed concerning their implications for music pedagogy and teacher intervention.

Background The spread of COVID-19 continues, the mutation of SARS-COV-2 is still difficult to control, and the need for antiviral drugs to treat COVID-19 remains urgent. The use of arbidol in the treatment of COVID-19 is limited and controversial. Methods To clarify the efficacy of arbidol on COVID-19, we collected 25 cases and 178 related studies. We analyzed the treatment information of arbidol based on the obtained cases, expanded the scope of the study, and collected current studies on the treatment of COVID-19 in various databases for in-depth analysis. Results History analysis showed that arbidol was effective (76% cure rate) compared with other drugs. However, compared with other antiviral drugs or standard therapy, the arbidol group had no significant advantage in reducing the time to negative virus transformation, length of hospital stays, or improvement in CT (MD=0.22, 95%CI -0.29-0.73; MD = 0.61, 95% CI 1.46 to 2.67; RR=1.15, 95%CI 0.88-1.50); Analysis of adverse events showed no significant difference between the arbidol group and the other groups (RR=0.82, 95%CI 0.25-2.71). Conclusion Our study showed that arbidol had no significant effect on COVID-19, but showed a slight advantage in CT improvement and adverse events. Our study objectively evaluated the efficacy of arbidol in the treatment of COVID-19 and provided some guidance for arbidol in the treatment of COVID-19.

A novel high-speed directly modulated two-section distributed feedback (TS-DFB) semiconductor laser based on the detuned-loading effect is proposed and simulated. Grating structure is designed by reconstruction-equivalent-chirp (REC) technique. A π phase-shift is introduced into the reflection grating, which can provide a narrow-band reflection region with a sharp falling slope on both sides of the reflection spectrum, thus enhancing the detuned-loading effect. Owing to its unique dual-falling-edges structure the bandwidth can be improved even when the lasing wavelength shifts beyond the left falling edge due to thermal effect in actual test, in which condition the detuned-loading effect can be used twice, which greatly improves the yield. The modulation bandwidth is increased from 17.5 GHz for a single DFB laser to around 24 GHz when the lasing wavelength is located on the left falling edge of the TS-DFB laser based on detuned-loading effect, and can be increased to 22 GHz for the right side. An eight-channel laser array with precise wavelength spacing is investigated, with side mode suppression ratio (SMSR) > 36dB. Besides, TS-DFB lasers with uniform reflection grating are studied and simulated result shows that modulation characteristic is far inferior to the laser with a phase-shifted grating reflector.

Laser additively manufactured (LAM) Ti–6Al–4V alloy has huge application potential in aerospace structural parts such as turbine blades. However, there are few studies on the fatigue properties of such LAM parts under vibration loading, particularly with regard to anisotropy. In this paper, vibration fatigue properties of LAM Ti-6Al-4V by laser melted deposition process were investigated along the transversely deposited (TD) direction and parallelly deposited (PD) direction. Through the first-order bending vibration experiments, LAM Ti-6Al-4V alloy exhibits obvious anisotropic fatigue properties and significant dispersion in fracture position. The fracture morphology analysis reveals that the vibration fatigue failure was mainly dominated by the LAM process-induced defects and the microstructure. For the LAM samples without defects at crack initiation sites, the fatigue behavior is controlled by the prior β columnar grains with preferential orientation, which leads to enhanced fatigue crack propagation resistance for the PD samples. For the LAM samples with defects at initiation sites, having lower fatigue lives, the fatigue anisotropy strongly depends on the projection area of the lack-of-fusion defects relative to the loading direction, resulting in better fatigue performance for the TD samples.

This work presents a multi-start algorithm for solving the capacitated vehicle routing problem with two-dimensional loading constraints (2L-CVRP) allowing for the rotation of goods. Researches dedicated to graph theory and symmetry considered the vehicle routing problem as a classical application. This problem has complex aspects that stimulate the use of advanced algorithms and symmetry in graphs. The use of graph modeling of the 2L-CVRP problem by undirected graph allowed the high performance of the algorithm. The developed algorithm is based on metaheuristics such as the Constructive Genetic Algorithm (CGA), to construct promising initial solutions; a Tabu Search (TS), to improve the initial solutions on the routing problem; and a Large Neighborhood Search (LNS), for the loading subproblem. Although each one of these algorithms allowed to solve parts of the 2L-CVRP, the combination of these three algorithms to solve this problem was unprecedented in the scientific literature. In our approach, a parallel mechanism for checking the loading feasibility of routes was implemented using multi-threading programming to improve the performance. Additionally, memory structures, like hash-tables, were implemented to save time by storing and querying previously evaluated results for the loading feasibility of routes. For benchmarks, tests were done on well-known instances available in the literature. The results proved that the framework matched or outperformed most of the previous approaches. As the main contribution, this work brings higher quality solutions for large-size instances of the pure CVRP. This paper involves themes related to the symmetry journal, mainly complex algorithms, graphs, search strategies, complexity, graph modeling, and genetic algorithms. In addition, the paper especially focuses on topic-related aspects of special interest of the community involved in symmetry studies, such as, graph algorithms and graph theory.

Extracellular vesicles are considered a novel therapeutic tool, due to their ability to transfer their cargoes to target cells. Different strategies to directly load extracellular vesicles with RNA species have been proposed. Electroporation has been used for the loading of non-active vesicles, however the engineering of vesicles already carrying a therapeutically active cargo is still under investigation. We here set up a coincubation method to increase the anti-tumor effect of extracellular vesicles isolated from human liver stem cells (HLSC-EVs). Using the coincubation protocol, vesicles were loaded with the anti-tumor miRNA-145, and their effect was evaluated on renal cancer stem cell invasion. Loaded HLSC-EVs maintained their integrity and miR transfer ability, and miR-145 was protected by RNAse digestion possibly due to its binding to RNA-binding proteins on HLSC-EV surface, such as Annexin A2. Moreover, miR-145 coincubated HLSC-EVs were more effective in inhibiting the invasive properties of cancer stem cells, in comparison to naïve vesicles. The protocol reported here exploits a well-described property of extracellular vesicles to bind nucleic acids on their surface and protect them from degradation, in order to obtain an effective miRNA loading that results in the increase of the effect of naïve active extracellular vesicles.

The effect of the different dental implants positioning region on the stress performance of the implant-supported prosthesis is not yet clear. This study evaluated the dental treatment with six dental implants in three different models and three different occlusal loading conditions, in terms of the biomechanical response of implants, prosthetic screw and maxilla, using three-dimensional finite element analysis. The finite element models were modelled containing external hexagon implants, as well as a Cobalt-Chromium superstructure. Three types of loads were applied: in the area of ​​the central incisors, first premolar and in the second molars. For the finite element simulations, the von-Mises stress peaks in the implant and in the surrounding cortical bone were analyzed. All recorded results reported higher values ​​for the implant-supported prosthesis in group C compared to the groups A and B. The highest stress values, ​​regardless the evaluated model, was in the prosthesis in group C and in screws, the smallest were in group A.

ABSTRACT: Iodixanol is an iso-osmolar nonionic dimeric hydrophilic contrast agent with a higher viscosity than the monomeric agents. It is the only Food and Drug Administration (FDA)approved isoosmolar agent in the United States, and it is the only contrast agent with an FDA-approved indication for use in cardiac computed tomographic angiography (CCTA), to assist in the diagnostic evaluation of patients with suspected coronary artery disease. In clinical studies, it has been noted to have fewer side effects and similar image quality when compared to low osmolar contrast media. This can be attributed to the pharmacological properties of iodixanol. In the field of cardiology, iodixanol among other intravenous contrast media is used for coronary computed tomography angiography and cardiac catheterization. In this article, the use, tolerability and efficacy of iodixanol in the field of cardiology are reviewed, specifically evaluating the use for CCTA and coronary angiography, including outcome studies, randomized trials and comparisons to other contrast agents.

Over recent decades, therapeutic proteins have had widespread success in treating a myriad of diseases. Glycosylation, a near universal feature of this class of drugs, is a critical quality attribute that significantly influences the physical properties, safety profile and biological activity of therapeutic proteins. Optimizing protein glycosylation, therefore, offers an important avenue to developing more efficacious therapies. In this review, we discuss specific examples of how variations in glycan structure and glycoengineering impacts the stability, safety, and clinical efficacy of protein-based drugs that are already in the market as well as those that are still in preclinical development. We also highlight the impact of glycosylation on next generation biologics such as T cell-based cancer therapy and gene therapy.

This paper uses the complex regression analysis method to establish the customer’s load regression models, which consider economic indicators, temperature and rainfall. Furthermore, the proposed models are used to study the forecasting feasibility of the future energy sales and summer peak load demand. At first, this paper used least-squares techniques to derive regression models for considering economic indicators and temperature of 34 customer energy sales and total energy sales. Besides, the AMI high voltage customer demand data and system generating capacity for 24 hours were adopted to forecast summer peak load. The above-mentioned data analysis tool is used by EViews software to achieve, in order to verify the feasibility of the research framework. The study found that although its forecasting model accuracy is low only when mixed with temperature and high voltage demands. So, when mixed with high voltage demand data and system generating capacity for 24 hours to forecast peak load, the average error is ± 0.87% and in the majority of its energy sales forecasting model of average error is ±3%. This result can provide power company as future reference.

Cenobamate is approved by the European Medicine Agency for the treatment of adult patients with epilepsy (PWEs) who suffer from ongoing focal-onset seizures despite appropriate treatment with at least two established antiseizure medications. Pivotal trials and post-marketing real-world observational studies have suggested a high efficacy with unusually high seizure-free rates. We sought to investigate the serum trough levels of cenobamate under steady-state conditions in seizure-free versus non-responding PWEs, and in PWEs who experienced adverse events versus those who did not. We analyzed samples from 101 PWEs treated with adjunct cenobamate under steady-state conditions. In all, 36 PWEs were seizure-free and 65 were non-responders. In 31 PWEs, adverse events were apparent, whereas in the remaining 70, no tolerability issues were reported. We found a linear correlation between the daily doses (range: 100 mg – 400 mg) and the plasma levels (3.8 mg/l – 54.6 mg/l). Neither the daily doses nor the plasma levels differed significantly between seizure-free and non-responding PWEs or between PWEs with a satisfactory tolerability and those who experienced adverse events. The main reason for this result was that the individual therapeutic ranges varied widely: seizure freedom and adverse effects were observed alongside low doses and plasma levels in some PWEs. Conversely, there were examples of PWEs who did not respond or who reported no tolerability issues at high doses or plasma levels. Still, to evaluate the individual therapeutic range and to better understand the influence of other drugs in cases where concomitant medications are used, the therapeutic drug monitoring of cenobamate may be useful.

Vitamin D deficiency and insufficiency are highly prevalent in CKD affecting over 80% of hemodialysis (HD) patients and require therapeutic intervention. Nephrological societies suggest the administration of cholecalciferol according to the guidelines for the general population. The aim of the observational study was to evaluate the efficacy and safety of the therapy with a high dose of cholecalciferol in HD patients with 25(OH)D deficiency and insufficiency to reach the target serum 25(OH)D level > 30 ng/mL. 22 patients (16 M), with an average age of 72.5 ± 13.03 years and 25(OH)D concentration of 13.05 (9.00–17.90) ng/mL were administered cholecalciferol at a therapeutic dose of 70,000 IU/week (20,000 IU + 20,000 IU + 30,000 IU, immediately after each dialysis session). All patients achieved the target value >30 ng/mL, with a mean time of 2.86 ± 1.87 weeks. In the first week, the target level of 25(OH)D (100%) was reached by 2 patients (9.09%), in the second week – by 15 patients (68.18%), in the fourth week – by 18 patients (81.18%) and in the ninth week by all 22 patients (100%). A significant increase in 1,25(OH)2D levels was observed during the study, however, only 2 patients (9.09%) achieved a concentration of 1,25(OH)2D above 25 ng/mL – the lower limit of the reference range. The intact PTH concentrations remained unchanged during the observation period. No episodes of hypercalcemia, and one new episode of hyperphosphatemia were observed. In conclusion, our study showed that the administration of a high therapeutic dose of cholecalciferol allowed for a quick, effective, and safe leveling of 25(OH)D concentration in HD patients.

We recently reported the isolation and characterization of an anti-SARS-CoV-2 antibody, called IgG-A7, that protected transgenic mice expressing the human angiotensin-converting enzyme 2 (hACE-2) from the infection with SARS-CoV-2 Wuhan. We show here that IgG-A7 protected 100% of the transgenic mice infected with Delta (B.1.617.2) and Omicron (B.1.1.529) at doses of 0.5 and 5 mg/kg, respectively. In addition, we studied the pharmacokinetic (PK) profile and Toxicology (Tox) of IgG-A7 in CD-1 mice at single doses of 100 and 200 mg/kg. PK parameters at those high doses were proportional to the dose, with the half-life in serum of ~10.5 days. IgG-A7 was well tolerated with no signs of toxicity in urine and blood samples, nor in histopathology analyses. Tissue Cross-reactivity (TCR) with a panel of mouse and human tissues showed no evidence of IgG-A7 interaction with tissues of these species, supporting the PK/Tox results in vivo and suggesting that while IgG-A7 has a broad efficacy profile it is not toxic in humans. The information generated in CD-1 mouse as PK/Tox model, complemented with the mouse and human TCR, could be of relevance as alternatives to NHPs in rapidly emerging viral diseases and/or quickly evolving viruses such as SARS-CoV-2.

Our study assessed the impact of using ovitraps with pyriproxyfen on mosquito populations and the feasibility of using human saliva samples to test for seroconversion to dengue virus (DENV). We used a quasi-experimental research design by forming the intervention (n=220) and the control (n=223) groups in neighboring Taguig City, Philippines, over four months. Socio-demographic data, entomological indices, and IgG antibodies against DENV were measured. Associations between the implementation of ovitraps dosed with pyriproxyfen and mosquito densities (percentage positive ovitraps and container indices) and DENV seroconversion were calculated post-intervention in Months 2, 3, and 4. Among participants recruited at baseline, 17 and 13 were seropositive for dengue (DENV) in the intervention and control groups, respectively. Both entomological indices were lower in the treated area than the control site at months two, three, and four post-interventions but not earlier. Dengue seroconversions rates did decrease in the treated population but not significantly so. In conclusion, the use of PPF-treated ovitraps impacted the mosquito population but not the seroconversion rates. Compliance to provide saliva samples and the ability to detect IgG antibodies within these samples were encouraging and suggested that further studies on a larger population and longer duration are warranted.

Aphasia is one of the most socially disabling post-stroke deficits. Although traditional therapies have been shown to induce adequate clinical improvement, aphasic symptoms often persist. Therefore, new rehabilitation techniques which act as a substitute or as an adjunct to traditional approaches are urgently needed. The present review provides an overview of the efficacy and safety of the most innovative approaches which have been proposed over the last twenty years. First, we examined the effectiveness of the pharmacological approach, principally used as an adjunct to language therapy, reporting the mechanism of action of each single drug for the recovery of aphasia. Results are conflicting but promising. Secondly, we discussed the application of Virtual Reality (VR) which has been proved to be useful since it potentiates the ecological validity of the language therapy by using virtual contexts which simulate real-life everyday contexts. Finally, we focused on the use of Transcranial Direct Current Stimulation (tDCS), both discussing its applications at the cortical level and highlighting a new perspective, which considers the possibility to extend the use of tDCS over the motor regions. Although the review revels an extraordinary variability among the different studies, substantial agreement has been reached on some general principles, such as the necessity to consider tDCS only as an adjunct to traditional language therapy.

Description of a novel bovine antimicrobial peptide and its antimicrobial spectrum. RNA isolation and RT-PCR were done from various tissues. DCD peptide was synthesized, and antimicrobial activity was analyzed. Bovine dermcidin gene contains five exons intermittent by 4 introns. Bovine DCD-mRNA was 398 bp with ORF 336 bp. Bovine DCD was expressed in skin and blood. Analysis of the amino acid compositions revealed that cysteine was repeated 6 times indicating the presence of 3 disulfide bonds that play role in the peptide stability. Staphylococcus epidermidis, Streptococcus bovis, and Enterococcus faecalis were affected by Bovine DCD peptide. Highest antimicrobial effect was at 50 and 100 µg/ml. The effect on Escherichia coli and Candida albicans was slightly low. In all bacteria, Bovine DCD peptide activity did not affect by varying pH values, but in Staphylococcus aureus, the activity was affected greatly at pH 4.5 and 5.5. The optimum salt concentrations were 100 and 50 mM NaCl with all bacterial strains and E. coli, respectively. In case of C. albicans, the antimicrobial activity of Bovine DCD peptide decreased with increasing the pH value regardless the NaCl concentration. The pH 6.5 of the sweat buffer was the optimum for the Bovine DCD peptide activity.

Background: Melatonin is a potent mitochondrial, cytoprotective and antioxidant molecule with potentially strong anti-aging properties. Topical melatonin has shown to improve the clinical signs of skin aging. Melatosphere™ is a new lipid-based delivery system able to improve stability and skin penetration of melatonin when used in topical formulations. No clinical studies, using objective instrumental data, are available so far regarding the positive effect of Melatosphere™ in improving wrinkles in women with mild-to-moderate skin aging. Study Aim: We evaluate, in an open prospective, evaluator-blinded trial, the effects on skin texture of 2 months treatment with a Melatosphere™ based cream. Subjects and Methods: 15 women aged >45 years with mild to moderate facial skin aging (Glogau score ≥2) participated in the trial, after their informed consent. An ANTERA 3D computer-assisted skin analysis evaluation for the assessment of coarse and fine wrinkles of the periorbital area and melanin content was performed at baseline and after two months of treatment. An evaluator-blinded Investigator Global assessment of skin elastosis, roughness, level of dyscromia, skin dryness and presence of actinic damage was also performed at the same time points using a 4-grade score from 0 (no sign) to 3 (severe sign). Results: At baseline the mean (SD) IGA score was 8.2(1.0). After 2 months the IGA score significantly decrease to 4.2(1.4) (49% reduction) (P=0.0007). ANTERA 3D evaluations showed a significant reduction in skin coarse and fine wrinkles volume in the target area of -31% and -18%, respectively. Melanin content was reduced significantly by -17%. Conclusion: Topical melatonin carried in Melatosphere improves in the short-term signs of skin aging evaluated clinically and by ANTERA 3D device in women with mild to moderate skin aging.

Using the culture-work-health model, this study investigates the factors influencing the quality of life of maritime workers. This study conducted a survey of 320 maritime workers who have experience living and working on a ship for more than six months. This self-administered questionnaire included questions on organizational culture and support, self-efficacy, perceived fatigue, as well as the quality of work life. Organizational culture and self-efficacy were identified as factors affecting the quality of work life, while organizational support was found to have an indirect effect after passing through self-efficacy and perceived fatigue. The final model accounts for 63.1% of the variance in maritime workers’ quality of life. As such, this study shows that self-efficacy is important for the quality of life of maritime workers, having both direct and indirect effects. Moreover, organizational support may prove the primary intervention point for relieving perceived fatigue and enhancing self-efficacy, thus improving the quality of work life.

Current instrumental technology in evaluating performance of skin care creams is still rather limited and there are no industrial standard testing equipment, method and performance specifications for it. In this paper, we report our attempt in using an instrument called PhabrOmeter for this purpose. PhabrOmeter is a commercialized instrument for sensory performance evaluation of textiles, leather, paper and nonwoven and has been designated by American Association of Textile Chemists and Colorists (AATCC) as a standard test method for textiles, AATCC TM 202 in 2013. By adopting artificial skin samples treated with skin care creams, we have developed a procedure to apply this instrument for evaluation of skin care creams from sample preparation, measurement to data analysis and interpretation. The results using commercial skin care creams to demonstrate the feasibility and advantages of this instrument are provided.

Cognitive impairment affects 34-65% of People with Multiple Sclerosis (PwMS), significantly impacting their quality of life. Clinicians routinely address cognitive deficits with in-clinic neuro-behavioural interventions, but accessibility issues exist. Telerehabilitation is a promising solution that utilises digital tools for home-based cognitive remediation. This narrative review assessed the feasibility and efficacy of cognitive telerehabilitation in PwMS, identifying 13 relevant studies. Regarding the feasibility of cognitive telerehabilitation, evidence shows adherence rates are generally good, although, surprisingly, not all studies reported a measure of compliance with the cognitive training explored. Considering the efficacy of different rehabilitative techniques on cognitive performance of PwMS, findings are generally inconsistent, with only one study reporting consistently positive results. A range of methodological limitations are reported as potential factors contributing to the variability of results. Overcoming some of these issues will be key. Upcoming research is necessary to determine optimal intervention approaches, long-term effects of rehabilitation, and how to best integrate the use of telerehabilitation into routine clinical practice. By exploiting digital tools in the best way and addressing methodological concerns, home-based rehabilitation holds the potential for improving cognitive functions and enhancing the quality of life in PwMS.

Soluble noble metal salts are widely used for loading noble metals as nano-catalysts in many applications. In this paper, Pt-SnO2 composite nanoceramics were prepared from SnO2 nanoparticles and H2PtCl6 using two Pt-loading methods separately: For the solution reduction method, the H2PtCl6 solution was added to a suspension of SnO2 and zinc powder to form Pt on SnO2 nanoparticles; and for the impregnation method, Pt was formed from H2PtCl6 in the course of sintering. Although a series of samples prepared using both Pt loading methods showed a strong response to H2 at room temperature, the ones prepared using the solution reduction method exhibited much better room temperature hydrogen sensing characteristics. For two samples of 0.5 wt% Pt and sintered at 825°C, the response value for the sample prepared using the solution reduction method was 5300 to 1% H2-20% O2-N2, which was much larger than that of 150 for the sample prepared using the impregnation method. Samples prepared using the two Pt loading methods have similar microstructures as characterized by XRD, FESEM, EDS, TEM, and HRTEM. However, the residual chlorine content in those using the impregnation method was found to be higher than that using the solution reduction method through analysis. It is proposed that the striking difference in the room temperature hydrogen sensing characteristics among samples prepared using these two different Pt loading methods separately resulted from their different chlorine removal process. This study demonstrates the importance of a proper method in loading noble metals from their soluble salts as nano-catalysts in many applications.

Dynamic Realistic Failure Process Analysis (DRFPA) is a numerical software based on FEM it is firstly validated by comparing with the experimental test. Such validation is carried out under two consistent concrete specimens under uniaxial compression. After validation, DRFPA is used to study the influence of two parallel pre-existing crack inclination angles on the fracture of concrete under dynamic loads. The evolution of wing cracks and secondary cracks is investigated by observing the initiation, coalescence, and propagation of them. Meanwhile, the relationship between failure mode and inclination angles is discussed via analyzing the acoustic emission events. Finally, it is concluded the relationship between inclination angles of pre-cracks and performance/stability of concrete structure.

This paper focused on the finite element analysis of structural system in extreme loading condition. Two different stud shape and thicknesses were analyzed under blast. The stud thickness such as 1.19 mm and 1.5 mm were modelled and analyzed using ABAQUS 6.14. FEM is a tool which predicts the engineering physics of the real structure. To validate the finite element modelling performed by authors, a reference work published by earlier researchers on cold-formed steel stud wall is considered and examined in the present study. The novelty of this study was web corrugation and influence of flange width on stud. The models mimic like an air bag in a car to delay the pressure timing inside the stud wall. The mass of explosive used as 1.56 kg at a standard scaled distance. Time versus displacement was captured out at four locations in the stud wall. One of the objectives is to develop mathematical model to validate the deformation of stud under blast loading. Two mathematical models were validated using Artificial Neural Network (ANN). The results captured in ANN model was error histogram, regression plot, best performance fit and training data. The models were capable of resisting the moderate blast load. The response surface methodology (RSM) was employed to evaluate model performance Regression equations are useful for predicting future trends and outcomes, which is crucial for planning and decision-making. The primary goal of this work is to evaluate cold-formed steel stud walls with varying stud sizes under blast loading using finite element analysis and validated by ANN and RSM.