The definition of UTC in 1972 balanced the needs of the time and frequency community for a universal time scale that was traceable to the definition of frequency in the SI system of units with the needs of the astronomical community for a time scale that was closely linked to UT1, a time scale related to the rotation of Earth. The balance between these two considerations has changed very significantly since 1972, and there is widespread agreement that the method of relating UTC to UT1 should be changed by increasing the maximum tolerance between the two scales to more than the current limit of 0.9 s. I propose to realize this decision by means of an algorithmic adjustment process based on the variation in the length of the day over the previous centuries. I use these historical data to extrapolate the length of the day for a century into the future, and to compute a periodic rate adjustment to UTC based on this extrapolation. The adjustment process will not use time steps. The magnitude of the periodic rate adjustment will be re-considered every century, but the basic adjustment algorithm will not change. I suggest a maximum tolerance between UT1 and UTC that is large enough to absorb the irregular and unpredictable variations in the length of the day with respect to the long-term average increase in this value but plays no role in determining the parameters of the adjustment process that is proposed. I also propose that the adjustment be implemented at 12 UTC on 1 January since that is closest to a universal holiday in all time zones.

The paper presents the results of experimental studies and mathematical modeling of the effect of stress accumulation in thermosetting epoxy polymer "hot" curing on anhydride hardener. Stress accumulation occurs under cyclic thermomechanical action in a locked rod, similar effects are observed, for example, in thermoplastic elements subjected to the combined effect of mechanical loads and variable temperatures. Experimental results have shown that under cyclic thermomechanical loading during exploitation it is possible to accumulate residual stresses in the thermosetting polymer. A multi-element structural mathematical model with memory for thermomechanical load, which allows to consider the accumulation of residual thermal stresses, has been proposed. The results of modeling and experiment are compared. Based on the results, corrections are made in the approach to the application of this model to thermosetting polymers such as the epoxy resin under study. Considering the corrections, a good agreement (the difference is from 1 to 6%) with the results of experimental determination of stresses under complex cyclic thermomechanical load was obtained.

Livestock farming plays a crucial role in agriculture and is important in meeting people's needs for a better life in the new era. However, due to China's "double carbon" target, the development of animal husbandry has been affected by the level of carbon emissions. To study the spatial dis-tribution and dynamic evolution of livestock carbon emissions in Shandong Province, we used panel data from 16 prefecture-level cities in Shandong Province from 2001 to 2022 to determine the spatial differentiation of livestock carbon emissions in Shandong Province and their dynamic evolution by combining spatial and non-parametric estimation methods based on livestock carbon emissions and livestock emission intensity measured by city. The results of the study show that the distribution of carbon emissions from animal husbandry in Shandong Province is in a "dis-persed-aggregated" pattern, and the intensity of carbon emissions shows a gradual downward trend, with a ladder-like distribution characterized by high in the west and low in the east. Through the analysis of the dynamic evolution of nuclear density, we observe that the regional differences of animal husbandry carbon emissions in Shandong Province are expanding, showing the characteristics of polarization. The difference of carbon emissions in the peninsula is gradually narrowing, and the phenomenon of polarization is weakening. The carbon emissions of animal husbandry in the central and western regions of Shandong are polarized.

This research investigates the fatigue behaviour and fracture mechanics of high-performance concrete (HPC), including various compositions such as HPC with basalt aggregates (HPC-B), HPC with gravel (HPC-G), and high-strength coarse mortar (CM) static and cyclic tensile loading within the special priority program SPP 2020. The study aims to integrate fracture mechanics into structural analysis to enhance design guidelines for slender cross-sections and safety-related high-performance structural components. The experimental investigations reveal HPC-B's re-markable superiority, displaying higher compressive strength, modulus of elasticity, and tensile strength compared to HPC-G and CM. A modified disk-shaped compact tension (MDCT) based on ASTM standards, aided by digital image correlation (DIC) unveils fracture behaviour, empha-sizing fracture energy as a crucial parameter. HPC-B exhibits improved crack resistance and notch sensitivity reduction attributed to crushed basalt aggregates and enhanced interfacial transition zone (ITZ). The research scrutinizes factors like material characterization, aggregate morphology, stress levels, and displacement rate on crack formation. High-cycle fatigue tests show HPC-B's superior performance, and post-fatigue analysis reveals enhanced residual fracture toughness attributed to nano-level structural changes, stress redistribution and aggregate-matrix interac-tion. 3D image analysis via Computed Tomography (CT) scans captures mesostructural crack propagation and provide quantitative insights. This study advances the understanding of HPC fatigue behaviour, emphasizing the interplay of aggregate types, morphologies, and their dy-namic response to cyclic loading, offering valuable insights for optimizing design guidelines and fostering innovation in structural engineering.

This paper seeks to model the crack propagation in of AAs (aluminum-alloys) 2524-T3 and 7050-T7452 subjected to fatigue loading at low temperature. Fatigue crack growth tests were performed on AAs 2524-T3 and 7050-T7452 subjected to constant-amplitude and actual random-spectra loading histories at room temperature of about 25 °C and at cryogenic temperature of -70 °C, respectively, to determine their crack growth properties and residual lives. The interaction mechanisms between cryogenic temperature and the fatigue load were deduced on the basis of the results of fractographic analysis. Temperature-dependent residual lives under actual random-spectrum load history were modeled based on a modified accumulation damage rule by accounting for the load interaction. Good correlation was achieved between the predictions and actual experiments, demonstrating the practical and effective use of the proposed method.

The rehabilitation of the road embankments alongside the irrigation canal, which is constructed on a Bangkok soft clay foundation, has resulted from land use growth for several decades. As a result, the embankment is always confronted with the problem of instability. Numerous articles have demonstrated that rapid drawdown of the water level in the canal could be one of the most significant reasons, whereas vehicle cyclic loading may potentially contribute to some effect of the embankment failure. To explore and assess the effects of the influence factors, the finite element method (FEM) and conventional and dynamic triaxial approaches were employed. The study also investigated the consequences of varying thicknesses of soft clay and cyclic loading with different magnitudes and frequencies. Consequently, cyclic loading can lead to an augmentation in strain distribution and excess pore water pressure. Likewise, more significant deformation and excess pore water pressure were induced by a lower frequency and deeper thickness of soft clay compared to a higher frequency and thinner thickness. In brief, vehicle repetitive loading is one of the primary factors contributing to embankment failure, with the threshold stress being approximately three-fourths of the undrained shear strength. In contrast, threshold strain is approximately one to two-fold of the monotonic strain condition.

Multiaxial fatigue experiments under asynchronous loadings with four different loading frequency ratios were carried out on 30CrMnSiA steel. The experimental results show that the fatigue life decreases when the axial or torsion frequency increases from 1 to 2, while there is no significant change when the axial or torsion frequency increases from 2 to 4. The surface crack paths are observed and show that cracks initiate on the maximum shear stress amplitude planes, propagate approximately tens of microns, and then turn to propagate along the maximum normal stress planes. The number of secondary cracks increases when the axial or torsion frequency increases. Subsequently, the Bannantine-Socie and Wang-Brown cycle counting methods along with various multiaxial fatigue criteria and Palmgren-Miner’s cumulative damage rule were used for fatigue life prediction. The experimental results are consistent with the fatigue life predicted by the Bannantine-Socie method with the section critical plane criterion for 30CrMnSiA steel under asynchronous loading paths.

Magnetoelectric (ME) sensor is a new type magnetic sensor with ultrahigh sensitivity, low power consumption, and suitable for the measurement of low frequency weak magnetic field. In this study, metglas/PZT-5B ME sensor with a mechanical resonance frequency f_res of 60.041 kHz was prepared. It is interesting to note that its magnetic field resolution reaches 0.20 nT at f_res and 0.34 nT for DC field, respectively. In order to measure the ultralow frequency AC magnetic fields, a frequency upconversion technique was employed. Under this technique, a limit of detection (LOD) of AC magnetic field lower than 1 nT at 8 Hz is obtained, and the minimum LOD of 0.51 nT is achieved at 20 Hz. The high resolution ME sensor with sub-pT level is promising in the field of low frequency weak magnetic field measurement technology.

Extremely low-frequency electromagnetic fields (ELF-EMF) are ubiquitous in industrial-11 ized environments due to the continuous use of electrical devices. Our previous studies demon-12 strated ELF-EMF affects muscle cells by modulating oxidative stress and enhancing myo-genesis. 13 This pilot study investigated these effects on skeletal muscles of sedentary adult mice, assessing 14 physiological responses to ELF-EMF exposure and potential modulation by antioxidant supplemen-15 tation. Male C57BL/6 mice were exposed to ELF-EMF (0.1 or 1.0 mT) 1 hour/day up to 5 weeks, and 16 fed a standard diet without or with N-acetyl-cysteine (NAC). Results showed transient increases in 17 muscle strength (after 2-weeks’ exposure at 1.0 mT), potentially linked to muscle fiber recruitment 18 and activation, revealed by higher PAX7 and MyH expression levels. After ELF-EMF exposure, ox-19 idative status assessment revealed transient increases in expression levels of SOD1 and catalase en-20 zymes, in total antioxidant capacity and in protein carbonyl levels, marker of oxidative damage. 21 These effects were partially reduced by NAC. In conclusion, ELF-EMF exposure affects skeletal 22 muscle physiology and NAC supplementation partially mitigates these effects, highlighting the 23 complex interactions between ELF-EMF and antioxidant pathways in vivo. Further investigations 24 on ELF-EMF as a therapeutic modality for muscle health are necessary.

Laser Photoacoustic Spectrometers (LPAS), which provide photoacoustic spectra for detecting food frauds or adulteration, and fluorescence-based systems for recognition of contamination by heavy metal ions in water are two important families of sensors for health and environmental purposes. Both sensor families require one or more low-frequency Lock-In Amplifiers (LIAs) to extract the signal of interest from background noise. In the cited applications, the required LIA frequency is quite low (up to 1kHz), and this leads to a simplification of the hardware with consequent good results in portability, economy, reduced size, weight and low-cost characteristics. The present system, called ENEA DSP Box Due, is based on a very inexpensive microcontroller proto-board and can replace four commercial LIAs, resulting in significant savings in both cost and space. Furthermore, it incorporates a dual-channel oscilloscope and a sinusoidal function generator. This article outlines the architecture of the ENEA DSP Box Due, its electrical characterization and its applications within a project concerning laser techniques for food and water safety.

Clinical work conducted over the last seventeen years at the EEG Institute in Los Angeles and by other neurofeedback providers around the world has demonstrated the utility of extending frequency-based neurofeedback deep into the infra-low frequency (ILF) region, using the method of endogenous neuromodulation described herein. The method is characterized by the absence of any overt reinforcements, which makes it possible to extend the clinical reach to extremely low frequencies. As the training frequency is lowered, the signal becomes more difficult to discriminate, and ultimately it can only be discerned by the brain itself, in the process of endogenous neuromodulation. The method emulates how the brain does skill learning in general: It must observe itself performing the skill, with feedback on its performance. While the immediate target of ILF neurofeedback is enhanced self-regulatory competence--with symptomatic relief and functional recovery the secondary consequences, progressive lowering of the target frequencies has led to improved outcomes in application to challenging dysfunctions such as episodic suicidality, migraine, seizures, and bipolar mood swings. The work has also yielded insights into how the frequency domain is organized. The training proceeds best at frequencies that are specific to each individual, and these are referred to as optimal response frequencies (ORFs). These frequencies differ for various placements but stand in two fixed relationships to one another, one that holds over the EEG spectral range, and another that holds over the entire ILF range. Training in the ILF region engages the dynamics of the glial-neuronal networks, which govern tonic, resting state regulation. The collective clinical experience with ILF neuromodulation within a large practitioner network supports the case for making protocol-based, individualized ‘homeodynamic’ regulation a therapeutic priority, particularly for our most impacted clinical populations: addiction, trauma formations, traumatic brain injury, and the dementias. The case is made for further outcome studies and foundational research.

Understanding and predicting damage progression within thin plain-woven CFRP components is an essential issue for scheduling maintenance intervals and structural inspections, and typically require extensive test series. However, uncertainties always remain and result in conservative design and unnecessary downtimes due to the repeated inspections of a healthy structure. SHM can be used to reduce these uncertainties, as it allows to evaluate the condition of a mechanical structure during operation. Numerous SHM methods are developed , that achieve different levels of damage identification but are often investigated at small coupons with non-realistic structural damages and loading conditions on both, structure and sensor. The present research investigates the electrical impedance tomography (EIT) featuring an elastoresistive thin-film sensor to evaluate damage that propagates from a circular hole in a large plate under cyclic tensile-tensile multi-block loading. Applied fatigue loads were increased multiple times up to a total number of two million cycles. During the loading damage initiated at the hole and continuously propagated into the plate. Repeated EIT evaluations of the applied sensor and validating evaluations by means of digital image correlation clearly revealed the robustness of the hardware and the potential of the SHM method for damage evaluation of plain-woven CFRP components.

Background: To compare the loss of preload in absence of loading and after a fixed number of ideal masticatory cycles in two different connection systems using all-on-four prosthetic model. Methods: Two equal models of an edentulous mandible rehabilitated with all-on-four technique with two types of abutment system (MUA and OT-Bridge) supporting a hybrid prosthesis, were used. Initial torque values of the prosthetic fixing screw, after ten minutes from initial screw tightening and after 400000 masticatory cycles were registered using a mechanical torque gauge. Differences between initial and final torque values were reported for each anchoring system and the two systems were finally compared. Results: No statistically significant differences regarding the loss of preload between MUA and OT-Bridge system were found after 400000 masticatory cycles; however, in MUA system it was found between anterior and posterior implant screws. A significant difference in preload loss was found only for MUA system comparing the initial screw torque to that measured after 10 minutes from the tightening in absence of cyclic loadings. Conclusions: MUA and OT-Bridge are reliable prosthetic anchoring systems able to tolerate repeated masticatory cycles also on distal cantilever in all-on-four rehabilitation model without any significant loss of preload in screw tightening

Observed sea surface Ka-band normalized radar backscatter cross section (NRCS) and Doppler velocity (DV) exhibit energy at low frequencies (LF) below the surface wave range. It is shown that non-linearity in NRCS-wave slope Modulation Transfer Function (MTF) and inherent NRCS averaging within the footprint account for the NRCS and DV LF variance with the exception of VV NRCS for which almost half of the LF variance is attributable to wind fluctuations. Although the distribution of radar DV is quasi-Gaussian suggesting virtually little impact of non-linearity, the LF DV variations arise due to footprint averaging of correlated local DV and non-linear NRCS. Numerical simulations demonstrate that MTF non-linearity weakly affects traditional linear MTF estimate (less than 10% for |MTF|< 20). Thus the linear MTF is a good approximation to evaluate the DV averaged over large footprints typical of satellite observations.

An analysis of the processes of plastic deformation and acoustic relaxation in a high-entropy alloy Al0.5CoCrCuFeNi was carried out. The following have been established: dominant dislocation defects; types of barriers that prevent the movement of dislocations; mechanisms of thermally activated movement of various elements of dislocation lines through barriers at room and low temperatures. Based on modern dislocation theory, quantitative estimates have been obtained for the most important characteristics of dislocations and their interaction with barriers.

Peptide-based opioid ligands are important candidates for the development of novel, safer, and more effective analgesics to treat pain. To develop peptide-based safer analgesics, we synthesized a mixture-based cyclic pentapeptide library containing a total of 24,624 pentapeptides and screened the mixture-based library samples using a 55 °C warm-water tail-withdrawal assay. Using this phenotypic screening approach, we deconvoluted the mixture-based samples to identify a novel cyclic peptide Tyr-[D-Lys-Dap(Ant)-Thr-Gly] (CycloAnt), which produced dose- and time-dependent antinociception with an ED50 (and 95% confidence interval) of 0.70 (0.52-0.97) mg/kg i.p. mediated by the mu-opioid receptor (MOR). Additionally, higher doses (≥ 3 mg/kg, i.p.) of CycloAnt antagonized delta-opioid receptors (DOR) at least 3 hours. Pharmacological characterization of CycloAnt showed the cyclic peptide did not reduce breathing rate in mice at doses up to 15 times the analgesic ED50 value, and dramatically less hyperlocomotion than the MOR agonist, morphine. While chronic administration of CycloAnt resulted in antinociceptive tolerance, it was without opioid-induced hyperalgesia and significantly reduced signs of naloxone-precipitated withdrawal suggestive of reduced physical dependence as compared to morphine. Collectively, the results suggest this dual MOR/DOR multifunctional ligand is an excellent lead for the development of peptide-based safer analgesics.

In this study, the degradation characteristics of radio-frequency (RF) low-noise amplifier (LNA) based on silicon-germanium (SiGe) heterojunction bipolar transistors (HBTs) due to total ionizing dose (TID) are investigated. The small-signal equivalent model of a SiGe HBT is utilized to analyze circuit-level performance including the input and the output matching and noise figure (NF). As a target circuit, an LNA with a cascode common-emitter stage with emitter degeneration is studied and the equation of each performance parameter is derived. The RF LNA fabricated using commercial 350 nm SiGe technology was exposed to X-ray irradiation with the total dose up to 3 Mrad (SiO2). The experimental results exhibit that modeled device parameters estimate the degraded circuit performance. In addition, the relative impact of each parameter on the circuit metrics is revealed, which is expected from the derived design equations. The key device parameters for modeling TID-induced circuit degradations include the base resistance, the transconductance, and the base-to-emitter capacitance.

The phonon modes in YBa₂Cu₃O_7-δ and YBa_2-xLa_xCu₃O_7-δ systems have been systematically studied by Raman spectroscopy. The new phonon modes of 104 cm^-1, 94 cm^-1, and 89 cm^-1 were found in all these samples. A crude estimate about the wavenumber of the collective vibration of the stable CuO2 plane was given in this paper. The standard deviations of the new phonons in YBa₂Cu₃O_7-δ and YBa_2-xLa_xCu₃O_7-δ systems were discussed. The results of the calculation indicated that the 104 cm^-1 mode probably stands the c-direction collective vibration of the stable CuO2 plane, the 94 cm^-1 mode stands the a-direction vibration, and the 89 cm^-1 mode stands b-direction vibration. The relevance between these phonons and the superconductivity was discussed. It is found that, as the T_c decreased, the 104 cm^-1 mode and the 94 cm^-1 mode softened, and the 89 cm^-1 mode hardened slightly.

This paper reviews non-intrusive load monitoring (NILM) approaches that employ deep neural networks to disaggregate appliances from low frequency data, i.e. data with sampling rates lower than the AC base frequency. We first review the many degrees of freedom of these approaches, what has already been done in literature, and compile the main characteristics of the reviewed publications in an extensive overview table. The second part of the paper discusses selected aspects of the literature and corresponding research gaps. In particular, we do a performance comparison with respect to reported MAE and F$_1$-scores and observe different recurring elements in the best performing approaches, namely data sampling intervals below 10\,s, a large field of view, the usage of GAN losses, multi-task learning, and post-processing. Subsequently, multiple input features, multi-task learning and related research gaps are discussed, the need for comparative studies is highlighted, and finally, missing elements for a successful deployment of NILM approaches based on deep neural networks are pointed out. We conclude the review with an outlook on possible future scenarios.

The stepwise hydrogenation of the C=C bond and C=O group of acrolein on Au₃ and Au₅ model systems is investigated using the density functional theory(DFT) PW91 functional. Our results show that the C=C hydrogenation is more favorable than that of C=O bond on Au₃ with the barriers of the rate-determining step being 0.35 and 0.62 eV respectively. On the other hand, the C=O reduction is preferred over the hydrogenation of the C=C bond on Au₅. The corresponding barriers of the rate-determining steps are 0.45 and 0.54 eV, respectively. This demonstrated that the second hydrogenation step controls the reaction on both Au₃ and Au₅ for C=O and C=C hydrogenation and the C=O hydrogenation on Au₅ is preferred over the hydrogenation of the C=C bond, which is helpful to address the reactivity of small size-selected supported gold clusters.

This research has developed a process for producing ZnO thin film from DEZn deposited onto a PET substrate with low-pressure, high-frequency Ar + O2 plasma using a chemical vapor deposition technique. The aim is to study the film production conditions that affect electrical properties, optical properties, and thin film surfaces. This work highlights the use of plasma energy produced from a mixture of gases between Ar + O2. Plasma production is stimulated with an RF power supply to deliver high chemical energy and push ZnO atoms from the cathode inside the reactor onto the substrate through surface chemical reactions. The results showed that increasing the RF power in plasma production affected the chemical reactions on the substrate surface of film formation. The film preparation at RF power 300 W will give the thickest films. The film has a continuous columnar formation, and the surface has a granular structure. This results in the lowest electrical resistivity of 1.8 x 10-4 Ω-cm. In addition, when fabricated into a DSSC device, the device tested the PCE value and showed the highest value at 5.68%. This is due to the very rough surface nature of the ZnO film, which increases the scattering and storage of sunlight, making cells more efficient. Therefore, the benefit of this research is that it will be a highly efficient prototype of thin film production technology using a chemical process that reduces production costs and can be used in the industrial development of solar cells.

This article addresses the problem of contact voltage increase caused by the low frequency oscillation of the train-grid system in the phase-separation process of the EMU. The article establishes the EMU-contact line-traction substation model, reveals the mechanism of low-frequency oscillation, and obtains the relationship between the separation phase angle of the pantograph with line and low-frequency oscillations. Methods to suppress the over-voltage during the low-frequency oscillation are proposed. The study shows that when the power phase angle of the pantograph-line separation is within the range of 60°~90° and 240°~270°, the voltage amplitude in the neutral zone is larger, the maximum amplitude can reach 52.2kV, and low-frequency oscillation will occur in the neutral zone. When low frequency oscillation occurs, the contact line voltage in the neutral zone is mainly 1/3 power frequency (16.7Hz). After installing an RC suppression device in the neutral zone, when the EMU enters the neutral zone, the absolute value of the voltage peak drops to below 20 kV. Compared with the situation where the suppression device is not connected, the absolute value of the voltage peak is reduced by nearly 60%. The study provides a basis for the design of the neutral zone of the contact line and the selection of the high-voltage equipment of the EMU.

Deep brain stimulation (DBS) of the subthalamic nucleus (STN) has become an effective and widely used tool in the treatment of Parkinson’s disease (PD). STN-DBS has varied effects on speech. Clinical speech ratings suggest worsening following STN-DBS, but quantitative intelligibility, perceptual, and acoustic studies have produced mixed and inconsistent results. Improvements in phonation and declines in articulation have frequently been reported during different speech tasks under different stimulation conditions. Questions remain about preferred STN-DBS stimulation settings. Seven right-handed, native speakers of English with PD treated with bilateral STN-DBS were studied off medication at three stimulation conditions: stimulators off, 60 Hz (low frequency stimulation - LFS), and the typical clinical setting of 185 Hz (High frequency - HFS). Spontaneous speech was recorded in each condition and excerpts were prepared for transcription (intelligibility) and difficulty judgements. Separate excerpts were prepared for listeners to rate abnormalities in voice, articulation, fluency, and rate. Intelligibility for spontaneous speech was reduced at both HFS and LFS when compared to STN-DBS off. Speech produced at HFS was more intelligible than that produced at LFS, but HFS made the intelligibility task (transcription) subjectively more difficult. Both voice quality and articulation were judged to be more abnormal with STN-DBS on. STN-DBS reduced the intelligibility of spontaneous speech at both LFS and HFS but lowering the frequency did not improve intelligibility. Voice quality ratings with STN-DBS were correlated with the ratings made without stimulation. This was not true for articulation ratings. STN-DBS exacerbated an existing voice disorder and may have introduced new articulatory abnormalities.

Dear Ladies and Gentlemen, I thank you for suggesting to submit the manuscript with the title “Insulin resistance develops due to an imbalance in the synthesis of cyclic AMP and the natural cyclic AMP antagonist prostaglandylinositol cyclic phosphate (cyclic PIP)” to the Editorial Board of the MDPI journal Stresses, and I ask for consideration to publish it in the journal Stresses. It was previously submitted to the MDPI journal Int. J. Mol. Sci. (IJMS-195 6513), but it was found that 1) it would not fit within the scope of this special edition and 2) it would primarily deal with cyclic PIP and would have not enough literature citation on the topic insulin resistance. The present version of the manuscript is improved, but the content is the same. The goal of this review is not to write again a summary on nearly all reports on insulin resistance as this was done by Dr. Petersen and Dr. Shulman, whose review has 961 literature citations. The present manuscript compiles what is known on cyclic PIP in relation to insulin resistance and the reason of writing this manuscript was that the discovered facts on cyclic PIP synthesis allow to suggest how insulin resistance most likely starts. Hitherto, reports on insulin resistance did not come close to this question. I am convinced that the manuscript makes an essential contribution to the question what causes the development of insulin resistance, and I have to say that stress overload is one of the reasons. Unfortunately, I have to mention a topic, about which I do not like to talk. Years ago, research groups postulated with rigor that the mediator of insulin action would be a peptide and then they suggested various, extracellularly synthesized glycans as mediators. They caused confusions and a high degree of disbelief in the matter of mediators of insulin action. In my review on cyclic PIP in IUBMB Life from 2020, I wrote in the introduction that cyclic PIP should not be confused with these mediators. But I cannot write this in the introduction of every report. I am keeping fingers crossed so that the editor in charge will find fair and openminded reviewers. Last not least I confirm that neither the manuscript nor any part of its content is currently under consideration or published in another journal. Kind regards, Henrich Wasner, PhD, BioReg Biopharm, TiLab; University of Illinois at Chicago; 2242 West Harrison St., Ste. 201, Chicago, Il 60612; USA

Low-frequency peaks in the Raman spectra of amorphous poly (ether ketone) (PEEK) are investigated. An amorphous sample with zero crystallinity, as confirmed by WAXRD, was used in this study. In a previous study, two peaks were observed in the low-frequency Raman spectra of crystallized samples. One of the peaks at 135 cm-1, disappeared for the amorphous sample. Furthermore, the peak at 50 cm-1 was observed for the first time in the crystallized sample. The peak at 50 cm-1, similar to the peak at 135 cm-1, disappeared in the amorphous state, and its intensity increased with increasing crystallinity. The origins of the two peaks were both associated with the Ph-CO-Ph-type intermolecular vibrational modes in the simulation. It was suggested that the Ph-CO-Ph vibrational mode observed in the low-frequency region of PEEK was strongly in-fluenced by the intermolecular order.

With the rapid development of electronic and communication technology in military radar, the demand for microwave absorbing materials in low-frequency with thin layer is growing increasingly. In this study, flexible Co3O4/CC (carbon cloth) composites derives from Co-MOFs (metal-organic frameworks)/CC are prepared by hydrothermal and thermal treatment processes. The flexible precursors of Co-MOFs/CC are calcined with different calcination temperatures, which the material structure, dielectric properties and microwave absorption performance are changed. With the increase of calcination temperature, the minimum reflection loss of the corresponding Co3O4/CC composites gradually moves to the lower frequency with thinner thickness. In addition, the Co3O4/CC composites with 25 wt% filler loading ratio exhibit the minimum reflection loss (RL) of -46.59 dB at 6.24 GHz with 4.2 mm thickness. When the thickness is 3.70 mm, the effective absorption bandwidth is 3.04 GHz from 5.84 to 8.88 GHz. This study not only proves that the composite Co3O4/CC is a kind of outstanding microwave absorbing material with better flexibility, but also provides a useful inspiration for the low frequency and broadband microwave absorbing material.

Foam concrete is a construction material with controllable low strength and untraditional physical properties. Its highly crushable nature leaves it a niche as an engineered energy-absorbing material in many value-added applications; however, fundamental understanding of the material properties is crucial. As foam concrete is highly cellularized and ductile, conventional concrete testing methods such as compression test are insufficient to characterize the key material attributes of foam concrete, especially when the foam density is low. The resonant frequency test (ASTM C215) is specified for evaluating dynamic Young’s modulus of normal concrete. Inspired by the non-destructive feature of this test, we investigate the possibility of using the resonant frequency test to continuously monitor the modulus build-up of foam concrete with age. For the representativeness of the samples, three variables are considered in material design—bulk density ranging from 0.4 to 1.2 g/cm3, water to cementitious materials ratio of 0.42 and 0.47, and fly ash replacement of 10 and 30% by weight of cement. After examining the different vibration modes, the fundamental transverse frequency is determined most suitable for interpreting the foam modulus. The experimental results demonstrate good accuracy of using this approach for the measurement of different samples. It is also confirmed that, for a given foam concrete, the foam modulus can be predicted by knowing the foam density and solid modulus of its base cement paste, which provides an important insight for the further studies and real applications of foam concrete.

In this paper, the Fourier-based synchrosqueezing transform (FSST) method is introduced into the power system to realize low frequency oscillation identification. Firstly, the modal components of low frequency oscillation signal are separated by FSST, and calculating the instantaneous parameters including magnitude, frequency and phase of every mode component with Hilbert transform. Then , calculating the damping ration of every modal component based on above parameters and derived the formulas. Thus, it realized effective identification of of modal parameters of low frequency oscillation signal. The experimental results of simulated data and 16-generator system demonstrate the validity and correctness of the FSST method. Comparing with the classical Prony method shows that the FSST method is better in the identification accuracy when the low frequency oscillation signal is polluted by noise. Finally, the effectiveness of the FSST in Actual power grid is verified based on the real data from Sichuan power grid.

This study delves into the atmospheric corrosion behavior of chromium-free complex-phase steel (CP), specifically investigating the influence of wet/dry frequency and ratio in cyclic corrosion tests (CCT). The study employs a modified ISO 14993 standard CCT method, which involves salt spray, dry, and wet stages. After 15 and 30 CCT cycles, mass loss, maximum corrosion depth, and corrosion products were analyzed to gain insights into corrosion mechanisms. In general, increasing the frequency and wet/dry stage ratio in CCT extends the time for autocatalytic reactions to occur, leading to accelerated localized CP corrosion and increased pitting factors. However, as the rust layer thickens, uniform corrosion may also intensify, so careful considerations are necessary. This study underscores the importance of controlling the frequency and ratio of wet/dry stages in CCT for effectively analyzing localized corrosion behavior in specimens.

The review presents the most developed by date hypotheses on the mechanisms of the influence of low-frequency magnetic fields (LFMF) on organisms. Biophysical models that explain the resonance-like responses of biological systems to LFMF with a specific frequency and amplitude are described. Two groups can be distinguished among these models: one considers ions-cofactors of proteins as the primary targets for the LFMF influence, and the other regards the magnetic moments of particles in biomolecules. Attention is paid to the dependence of resonance-like LFMF effects on the cell type. A radical-pair mechanism of the magnetic field's influence on biochemical processes is described with the example of cryptochrome. Conditions for this mechanism's applicability to explain the biological effects of LFMF are given. A model of the influence of LFMF on radical pairs in biochemical oscillators, which can explain the frequency-amplitude efficiency windows of LFMF, is proposed.

One of the relevant goals in forging technologies is simplifying the existing process and developing new processes that can retain the original or very close to the original dimensions and billet shape after the end of the deformation cycle. This study attempts to develop a forging equipment design that provides alternating cyclic loading; the alternate cyclic forging (ACF) method is proposed. To preliminary evaluate the ACF and study the plastic deformation behavior, numerical simulation via finite element modeling (FEM) was conducted using DEFORM-3D. The main attention was paid to the metal flow characteristics, effective strain and stress distribution, and the forging load. The ACF results in non-uniform metal flow with the formation of diagonal and vortex flows were demonstrated. Maximum effective strains and stresses zones are localized at two points of the billet contact with the surface of the tooling container and at two points of the interface between the punches. It was also assumed that reducing the contact area between the punch and the billet using separate semi-cylindrical punches can reduce the forging load. Preliminary finite element analysis (FEA) results of the proposed process after four successive steps of the deformation cycle confirmed the feasibility of its general implementation.

We report a preliminary exploration on the low-pressure Ar-O2 plasma generated by low-frequency alternating current (AC) power supply in the low-temperature Plasma Experimental Power Supply (CTP-2000S) for the first time. The electron density 〖(n〗_e), the electron temperature 〖(T〗_e) and the electron energy distribution function (EEDF) are measured by the single Langmuir probe in this experiment. Experimental results show that the ne increases with gas pressure rising, while the ne decreases with the oxygen concentrations rising. And, a plasma density peak is also observed with the AC power supply increase. A comparison between this work and the previous results by RF source suggests that the low-frequency AC power supply may be very fruitful exploration to generate the low-pressure plasma.

The vibration response of soil is a key property in the field of agricultural soil tillage. Vibration components of tillage machinery are generally used to reduce tillage resistance and improve work efficiency, the pressure variation under low-frequency vibration will affect the fragmentation and dispersion of farmland soil. However, the gradient of pressure variation, frequency domain response, and effective transmission range are unclear. A new method based on DEM (Discrete Element Method) is presented to study the vibration response and pressure transmission under low-frequency vibration. Bench test results showed that peak pressure positively correlates with the vibration frequency and attenuates rapidly at the vibration distance of 100 to 250 mm. The results data were also selected to determine the simulation model parameters. Amplitude, vibration frequency, and soil depth were used as test factors in single-factor simulation tests, and their effects on the peak pressure, frequency domain response, and effective transmission distance were analyzed. The results showed a positive relationship between the peak pressure and the test factors. The peak pressure increases with a maximum gradient of 19.02 kPa/mm at a vibration distance of 50 mm. The amplitude, vibration frequency, and soil depth positively correlate with the dominant frequency amplitude. The main frequency is independent of amplitude and soil depth. At the vibration distance of 250 mm, the dominant frequency is approximately twice the vibration frequency at 7–11 Hz and approximately equal to the vibration frequency at 13–15 Hz. Multiple exponential functions were used to fit the peak pressure attenuation function, obtaining an effective transmission distance range of 347.15 to 550.37 mm for the 5kPa cut-off pressure. For a soil depth of 300 mm, the vertical shear wave diffusion angle is greater than the horizontal shear wave diffusion angle. The study clarifies the vibration response of soil under low-frequency vibration, which helps to design vibration type soil-engaging components of tillage machinery and match vibration parameters for energy saving and resistance reduction in soil tillage.

Background: Electrical conductivity of trabecular bone at 100 kHz was recently reported as a good predictor of bone volume fraction. However, to quantify its relationship with the free water (or physiological solution) content and between the conductivities of its constituents, is still unclear. Methods: In this contribution, in silico models inspired by microCT images of trabecular bovine samples were used to build realistic geometries. Finite Element Method was applied to solve the electrical problem and to robustly fit the conductivity of the constituents with literature data. The obtained effective electrical conductivity was compared to Bruggeman three media mixture model: physiological solution, bone marrow and bone matrix. Results: The values for physiological solution plus bone marrow and bone matrix that captured better the bone volume fraction in the two media Finite Element model were: σps+bm = 298.4 mS/m and σb = 21.0 mS/m, respectively. Additionally, relative good results were obtained by a three media Bruggeman mixture model with σbm= 103 mS/m, σb= 21.0 mS/m, and σps= 1200 mS/m. Simple linear relationships between the proportions of constituents depending on bone volume fraction were tested. Degree of anisotropy and fractal dimension do not show detectable changes in effective conductivity. Conclusions: These results provided some useful findings for simulation purposes: first, a higher value of electrical conductivity of bone marrow has to be used in order to obtain similar values to those experimental published data. Second, anisotropy is not detectable by conductivity measurements for small trabecular samples (cube 5 mm). Finally, the simulations presented here showed a relatively good fitting of the mixture Bruggeman model which potentially would allow both, accounting for the free water content and re-scaling the model for whole bone electrical simulations.

With the advent of deep learning, significant progress has been made in low-light image enhancement methods. However, deep learning requires enormous paired training data, which is challenging to capture in real-world scenarios.To address this limitation, this paper presents a novel unsupervised low-light image enhancement method, which first introduces the frequency domain features of images in low-light image enhancement tasks. Our work is inspired by imagining a digital image as a spatially varying metaphoric “field of light”, then subjecting the influence of physical processes such as diffraction and coherent detection back onto the original image space via a frequency-domain to spatial-domain transformation (inverse Fourier transform). However, the mathematical model created by this physical process still requires complex manual tuning of the parameters for different scene conditions to achieve the best adjustment. Therefore, we proposed a dual-branch convolution network to estimate pixel-wise and high-order spatial interactions for dynamic range adjustment of the frequency feature of the given low-light image. Guided by the frequency feature from the “field of light” and parameter estimation networks, our method enables dynamic enhancement of low-light images. Extensive experiments have shown that our method performs well compared to state-of-the-art unsupervised, and its performance approximates the level of the state-of-the-art supervised methods qualitatively and quantitatively. At the same time, the light network structure design allows the proposed method to have an extremely fast inference speed(nearly 150 FPS on an NVIDIA 3090 Ti GPU for an image of size 600×400×3 ). Furthermore, the potential benefits of our method to object detection in the dark are discussed.

In this paper, a novel pendulum-type accelerometer based on hetero-core fiber optics has been proposed for structural health monitoring targeting large-scale civil infrastructures. Vibration measurement is a non-destructive method for diagnosing the failure of structures by assessing natural frequencies and other vibration patterns. The hetero-core fiber optic sensor utilized in the proposed accelerometer can serve as a displacement sensor with robustness to temperature changes in addition to immunity to electromagnetic interference and chemical corrosions. Thus the hetero-core sensor inside the accelerometer measures applied acceleration by detecting the rotation of an internal pendulum. A series of experiments showed that the hetero-core fiber sensor linearly responded to the rotation angle of the pendulum ranging within ±5°, and furthermore the proposed accelerometer could reproduce the waveform of input vibration in a frequency band of several Hz order.

Aim: Deep brain stimulation (DBS) involves implanting electrodes in specific brain areas. High-frequency Stimulation (HFS) and low-frequency Stimulation (LFS) target motor and non-motor symptoms differently. DBS is crucial in Parkinson's disease treatment for managing medication-resistant symptoms and improving quality of life. This review aims to evaluate the differential impact of high-frequency and low-frequency deep brain stimulation (DBS) on motor symptoms in Parkinson's disease (PD) patients. This systematic review adheres to PRISMA guidelines and focuses on clinical studies involving human subjects. Methods: Systematic search in electronic databases (PubMed, Google Scholar, Science Direct, Cochrane Collaboration Database of Randomized Trials) was performed to identify randomized controlled trials (RCTs) up to 13th July 2024. Results: Among 126 pooled patients from 8 RCTs, it was found that LFS significantly improved gait stability, swallowing, and verbal fluency with minimal adverse effects. Conversely, HFS was effective in reducing rigidity and tremor but was associated with potential side effects such as gait and speech impairment. Conclusion: The review highlights the nuanced effects of STN-DBS frequencies in Parkinson's treatment, suggesting high-frequency improves rigidity and tremor but may cause side effects, while low-frequency enhances gait stability and speech, necessitating further research for optimized, patient-specific therapies.

In recent years, electroencephalogram (EEG) emotion recognition has emerged as a research hotspot in the field of artificial intelligence (AI). Despite advancements in EEG-based emotion recognition, room for enhancing performance persists due to EEG signal redundancy and limitations in feature extraction, leading to inefficient models and emotional information loss. To fully utilize EEG's emotional information and improve recognition accuracy while reducing computational costs, this paper proposes a Convolutional-Recurrent Hybrid Network with a dual-stream adaptive approach and an attention mechanism (CSA-SA-CRTNN). Firstly, the model utilizes a CSAM module to assign corresponding weights to EEG channels. Then, an adaptive dual-stream convolutional-recurrent network (SA-CRNN and MHSA-CRNN) is applied to extract local spatial-temporal features. After that, the extracted local features are concatenated and fed into a temporal convolutional network with a multi-head self-attention mechanism (MHSA-TCN) to capture global information. Finally, the extracted EEG information is used for emotion classification. We conducted binary and ternary classification experiments on the DEAP dataset, achieving 99.26% and 99.15% accuracy for arousal and valence in binary classification, and 97.69% and 98.05% in ternary classification, surpassing relevant algorithms. Additionally, the model's efficiency is significantly higher than other models, achieving better accuracy with lower resource consumption.

A labyrinth metamaterial wall with glass coverage is measured in a reverberating chamber and after its installation in a restaurant. Glass is used to meet two aims, namely acoustic absorption and visual design demands. The wall consists of five multiple labyrinth elements of 1.83 m$^2$ each. Glass was taken to make the wall act as a room lightning device where a translucent cover material is needed. Absorption measurements show about four times improved absorption compared to typical glass. Due to the metamaterial behavior, absorption is high in the low-frequency range below 300 Hz where damping is problematic with traditional materials. Especially in this range, the glass metamaterial wall is an excellent compromise between room acoustic and visual design demands, as loud low-frequencies make visitors speak louder and experience less intimacy with additionally reduced speech intelligibility. For mid-frequencies, absorption is shown less effective and improvements are discussed.

With technological transformations such as big data, blockchain, artificial intelligence, and cloud computing, digital techniques are penetrating the field of finance. Digital finance is a resource-saving and environmentally friendly innovative financial service. It shows great green attributes and can drive the flow of financial resources towards environmentally friendly enterprises, thereby promoting green and low-carbon development. This paper investigates the effects of digital finance on green and low-carbon cyclic development and the mechanism. First, the level of green and low carbon cyclic development in China is estimated from multiple aspects based on the panel data of 31 provinces by using the spatio-temporal range entropy weight method. Then, the working mechanism of digital finance on green and low carbon cyclic development is revealed by performing empirical tests based on panel regression models, mediating effect models, and threshold models. Finally, the effects of digital finance and conventional variables on green and low-carbon cyclic development are investigated by using a random forest model and a CatBoost model in based on the machine learning. The results show that digital finance has significant positive effects on green and low-carbon cyclic development, and technological innovation plays a key role in the effects of digital finance on green and low-carbon cyclic development; meanwhile, the driving effect of digital finance on green and low carbon cyclic development shows nonlinear features with increasing “marginal effect”; besides, both digital finance and conventional factors have significant impacts on green and low carbon cyclic development. This study provides an empirical basis and path reference for digital finance to achieve “carbon peak, carbon neutralization” in China.

Although extracorporeal membrane ventilation offers the possibility for low frequency ventilation, protocols commonly used in patients with acute respiratory distress syndrome (ARDS) and treated with extracorporeal membrane oxygenation (ECMO) vary largely. Whether strict adherence to low frequency ventilation offers benefit on important outcome measures is poorly understood. Background/Objectives: This pilot clinical study investigated the efficacy of low frequency ventilation on ventilator free days (VFDs) in patients suffering from ARDS treated with ECMO therapy. Methods: In this single-center randomized controlled trial, 44 (70% male) successive ARDS patients treated with ECMO (aged 56 ± 12 years, SAPS III 64 (SD ± 14)) were randomly assigned 1:1 to control group (conventional ventilation) or treatment group (low fre-quency ventilation during first 72 hours on ECMO: respiratory rate 4-5/min; PEEP 14-16cm H2O; plateau pressure 23-25 cm H2O, tidal volume: < 4mL/kg). The primary endpoint was VFDs at day 28 of ECMO start. The major secondary endpoint was ICU mortality, 28-day and 90-day mortality. Results Twenty-three (52%) patients could be successfully weaned from ECMO and were discharged from intensive care unit (ICU). Twelve patients in the treatment group and five patients in the control group showed more than one VFD at day 28 after ECMO. VFDs were 3.0 (SD ± 5.5) days in the control group and 5.4 (SD ± 6) days in the treatment group (P = 0.117). Until day 28 after ECMO initiation, patients in the treatment group could be more often successfully weaned from ventilator (OR of 0.164 of 0 VFDs at day 28 after ECMO start; 95% CI 0.036-0.758; P = 0.021). ICU mortality did not differ significantly (36% in treatment group and 59% in control group; P = 0.227). Conclusions: Low frequency ventilation is comparable to conventional protec-tive ventilation in patients with ARDS treated with ECMO. However, low frequency ventilation may support weaning from invasive mechanical ventilation in patients suffering from ARDS treated with ECMO therapy.

In recent years, researches on combining wavelet decomposition and convolutional neural network (CNN) together to classify hyperspectral images (HSI) have emerged, and some effective classification models have been proposed and achieved good classification results. However, there are two problems for most of the proposed models. One is the heavy training parameters and the other is that there is no distinction between the classification effectiveness of low frequency and high frequency features after wavelet decomposition. In this paper, a new light-weighted HSI classification model (LLFWCNN) is proposed, which performs multi-layer wavelet decomposition for HSI after dimensionality reduction, and only arranges the low frequency features in a specific stack mode, then classifies them through a well-designed convolutional neural network. Compared with other classification models, the number of parameters is only 2.5% of that of other models. And only the low frequency features after wavelet decomposition are used, while the high frequency features are abandoned. The results showed that compared with the state-of-the-art classification models, LLFWCNN could obtain the same or even better classification results with fewer network parameters and proved that the low frequency features after wavelet decomposition provide LLFWCNN with more favorable information for HSI classification as well.

In recent years, magnetic fields have emerged as a non-thermophysical treatment with a signifi-cant impact on microbial fermentation processes. Brassica trispora is a microorganism known for its indus-trial-scale production of lycopene and high yield of single cells. This study aimed to in-vestigate the impact of low frequency magnetic fields on lycopene synthesis by Brassica trispora and elucidate the underlying mechanism for enhancing lycopene yield. The results indicated that both the intensity and duration of the magnetic field treatment influenced the cell. Exposing the cell to a 0.5 mT magnetic field for 48 hours on the second day of fermentation resulted in a lyco-pene yield of 1473.16 mg/L, representing a re-markable increase of 216.1% compared to the con-trol group. Transcriptome analysis revealed that al-ternating magnetic field significantly up-regulated genes related to ROS and cell membrane structure, leading to a substantial increase in lycopene production. Scanning electron microscopy revealed that the magnetic field treatment resulted in rough, loose, wrinkled surface morphology of the mycelium, along with a few mi-cropores, thereby altering the cell membrane permeability to some extent. Moreover, there was a significant increase in intracellular ROS content, cell membrane permeability, key enzyme activi-ty involved in lycopene metabolism, and ROS-related enzyme activity. In conclusion, the alter-nating fre-quency magnetic field can activate a self-protective mechanism that enhances lyco-pene synthesis by modulating intracellular ROS content and cell membrane structure. These find-ings not only deepen our understanding of the impact of magnetic fields on microbial growth and metabolism but also provide valuable insights for developing innovative approaches to en-hance carotenoid fermentation.

We offered the circuit of a discrete analog filter (DAF) low frequencies of second-order on switchable capacitors, which differs from the known ones in that three capacitors with one terminal are connected to a common bus, and the frequency of the DAF pole depends not only on the ratio of the capacitances of the frequency-setting capacitors, but also on the ratio of resistances two additional resistors in the feedback. This allows at constant values ​​of the capacitances and a fixed switching frequency of electronic switches, control the pole frequency by changing the resistance ratio of additional resistors. Computer simulation of the developed circuit was performed in the Micro-Cap environment. It has been established that the DAF has a transmission coefficient close to minus one at very low frequencies and a transmission coefficient close to zero at higher frequencies.

The unreliable prediction of the low frequency components from inverted acoustic impedance causes uncertainty in quantitative seismic interpretation. To address this issue, we first calculate various seismic and geological attributes that contain low frequency information, such as relative geological age, interval velocity, and integrated instantaneous amplitude. Then, we develop a method to predict the low frequency content of seismic data using these attributes, their high frequency components, and recurrent neural networks. Next, we test how to predict the low frequency components using stacking velocity obtained from velocity analysis. Using all the attributes and seismic data, we propose a supervised deep learning method to predict the low frequency components of the inverted acoustic impedance. The results obtained in both synthetic and real data cases show that the proposed method can improve the prediction accuracy of the low frequency components of the inverted acoustic impedance, with the best improvement in a real data example of 57.7% compared with the impedance predicted using well log interpolation.

: We evaluated the pharmaceutical properties of levofloxacin (LV) in the form of an orally disintegrating tablet (LVODT) to find a new usefulness of low frequency (LF) Raman spectroscopy. LVODT contained dispersed granules with diameters in the order of several hundred micrometers, which were composed of the active pharmaceutical ingredient (API), as confirmed by infrared (IR) microspectroscopy. On the contrary, the API and inactive pharmaceutical ingredients (non-APIs) were homogeneously distributed in LV tablet (LVT) formulations. Microscopic IR spectroscopy and thermal analyses showed that LVODT and LVT contained the API in different crystalline forms or environment around the API each other. Furthermore, powder X-ray diffraction showed that LVT contained a hemihydrate of the API, while LVODT showed a partial transition to the monohydrate form. This result was confirmed by microscopic LF Raman spectroscopy. Moreover, this method confirmed the presence of thin layers coating the outer edges of the granules that contained the API. Spectra obtained from these thin layers indicated the presence of titanium dioxide, suggesting that the layers coexisted with a polymer that masks the bitterness of API. The microscopic LF Raman spectroscopy results in this study indicated new applications of this method in pharmaceutical science.

Based on the dynamic strength variation mechanism of concrete under complex loading conditions, two approaches were devised: numerical testing and CT scanning, guided by the principle of minimizing energy dissipation. A methodology for calculating concrete's failure area and measuring its strength was developed. The analysis delves into the mechanisms behind failure patterns and variations in concrete specimen strength, focusing on crack initiation, development, and the resultant failure surface formed by crack propagation, along with the stress distribution in concrete specimens subjected to diverse loading conditions. Through evaluating the strength and computed failure area of concrete specimens, it is evident that the loading method influences both the strength and failure area of concrete specimens. In general, a larger failure area correlates with a higher measured strength.

Obesity is associated with serious comorbidities and economic implications. Bariatric surgery, most commonly Roux-en-Y gastric bypass and sleeve gastrectomy, are effective options for weight loss and improvement of obesity-related comorbidities. With the growing obesity epidemic, there has been a concomitant rise in bariatric surgeries, particularly in sleeve gastrectomy, which has been the most widely performed bariatric surgery since 2013. Gastroesophageal reflux disease (GERD) is highly prevalent in obese individuals, can significantly impact quality of life and may lead to serious complications. Obesity and GERD both improve with weight loss. However, as the incidence of sleeve gastrectomy rises, recent data has revealed a risk of exacerbation of pre-existing GERD or the development of de novo GERD following sleeve gastrectomy. We performed a detailed review of GERD post-sleeve gastrectomy, including its overall incidence, pathophysiology and current treatment paradigms.

The paper explores the potential of a low-cost advanced video-based technique for the assessment of structural damage induced to buildings by seismic loading. A low-cost high-speed video camera was utilized for motion magnification (MM) processing of footages of a two-story reinforced concrete frame building subjected to shaking table tests. The damage after seismic loading was estimated by analyzing the dynamic behavior (i.e. in terms of modal parameters) and the structural deformations of the building in the MM videos. The results by MM were compared for method validation to damage assessment obtained by the analyses of conventional accelerometers and high-precision optical markers tracked by a passive 3D motion capture system. Also, 3D laser scanning to obtain an accurate survey of the building geometry before and after the seismic tests was carried out. In particular, accelerometers were also processed and analyzed by using several stationary and non-stationary techniques with the aim to analyze the linear behavior of the undamaged structure and the nonlinear structural behavior during damaging shaking table tests. The proposed MM-based procedure provided accurate estimate of the main modal frequency and the damage location through the analysis of modal shapes, which were confirmed by advanced analyses of accelerometric data.

This study presents the utilization of the Microwave InfraRed Thermography (MIRT) technique to identify and analyze the defects in the carbon-fiber-reinforced polymer (CFRP) composite rein-forcement of concrete specimens. At first, a set of the numerical models was created, comprising of the broadband pyramidal horn antenna and the analyzed specimen. The utilization the system operating at a power of 1000W in a continuous mode, operating at frequency of 2.45 GHz was analyzed. The specimen under examination comprised a compact concrete slab that was covered with an adhesive layer, thereafter, topped with a layer of CFRP. An air gap represented a defect at the interface between the concrete and CFRP within the adhesive layer. In the modelling stage the study investigated three separate scenarios: a sample with no defects, a sample with a defect located at the center, and a sample with a numerous additional random defects located at the rim of the CFRP matte, to analyze the effect of the natural reinforcement degradation in this area. The next phase of the study involved conducting experiments to confirm the results obtained from nu-merical modeling. In the experiments the concrete sample aged for 10 years with the defect in the center and naturally developed defects at the CFRP rim was used. The study employed numerical modeling to explore the phenomenon of microwave heating in complex structures. The aim was to assess the chosen antenna design and identify the most effective experimental setup. These con-clusions were subsequently confirmed through experimentation. The observations made during the heating process were particularly remarkable, since they deviated from earlier studies that solely conducted measurements of the sample post-heating phase. The findings demonstrate that MIRT has the capacity to be employed as a technique for detecting flaws in concrete structures reinforced with CFRP.

Due to the continued deepening of today’s mining projects, there is a need to develop new or improved rockbolts that are strong and yielding and have high energy absorption when exposed to dynamic loading. Impact tests can provide useful information about the dynamic response of rockbolts but most laboratory tests involve high costs in preparation and result validation. Numerical modeling is an alternative that, in addition to complementing laboratory results, can be used to represent the process of deformation and energy absorption of support elements. In this paper the implementation and results obtained from a finite difference (FDM) numerical model are presented. The model functions as a simulation tool to illuminate all the elements that conform the large-scale (1:1) impact test and their behavior and influence on the dynamic response of a threadbar bolt (22 mm nominal diameter). The model was calibrated using published results and based on these results as well as parametric analysis, the response of each component (steel tube, grout, and bolt) could be identified and its behavior in terms of absorbed energy and displacement could be observed. Results show the model can provide important preliminary information to make design decisions about support elements design.

If "quantization is an art" then it can be greatly rened by adopting cyclic time formalism. In past papers we have proven the effectiveness of a formulation of physics based on cyclic relativistic time. Now we can demonstrate in a general way, by using theorems of Geometric Quantization, that the Poisson brackets of intrinsically cyclic time dynamics directly imply the ordinary canonical commutation relations and the other Dirac's rules of canonical Quantum Mechanics. In other words, according to our result, canonical quantization is an implicit way of imposing intrinsically cyclic time dynamics without explicitly saying that time is a cyclic dimension.

This paper presents a two-stage ADC based on pseudo-differential operational transconductance amplifier (OTA), which is designed for the readout circuit of X-ray linear array sensor. This hybrid ADC employs an incremental sigma-delta ADC and a cyclic ADC, achieving a good trade-off between accuracy and conversion speed. The two stages share the same hardware to reduce power consumption and die area. A common-mood feedback module is used to suppress the influence of charge injection, and the effectiveness is demonstrated by detailed theoretical analysis. A test chip of 14-bit ADC is fabricated in 0.35μm CMOS technology. The measured root mean square (RMS) value of DNL is 0.254 LSB, and the maximum value of INL is -0.776/+1.56 LSB. The measured effective number of bits (ENOB) is 13.43 bits.

This article is devoted to the problem of genetically coding of inherited cyclic structures in biological bodies, whose life activity is based on a great inherited set of mutually coordinated cyclic processes. The author puts forward and arguments the idea that the genetic coding system is capable of encoding inherited cyclic processes because it itself is a system of cyclic codes connected with Boolean algebra of logic. In other words, the physiological processes in question are cyclical because they are genetically encoded by cyclic codes. In support of this idea, the author presents a set of his results on the connection of the genetic coding system with cyclic Gray codes, which are one of many known types of cyclic codes. This opens up the possibility of using for modeling inherited cyclic biostructures those algebraic and logical theories and constructions that are associated with Gray codes and have long been used in engineering technologies: Karnaugh maps, Hilbert curve, Hadamard matrices, Walsh functions, dyadic analysis, etc. Additionally, the connections of these constructions with statistical rules of genomic DNAs and binary-genomic numbers are considered.

Fast-scan cyclic voltammetry (FSCV) is an electrochemical sensing technique that can be used for neurochemical sensing with high spatiotemporal resolution. Carbon fiber microelectrodes (CFMEs) are traditionally used as FSCV sensors. However, CFMEs are prone to electrochemical fouling caused by oxidative byproducts of repeated serotonin (5-HT) exposure, which makes them less suitable as a chronic 5-HT sensor. Our team is developing a boron-doped diamond microelectrode (BDDME) that has previously been shown to be relatively resistant to fouling caused by protein adsorption (biofouling). We sought to determine if the BDDME exhibits resistance to electrochemical fouling, which we explored on electrodes fabricated with either femtosecond laser cutting or physical cleaving. We recorded the oxidation current response after 25 repeated injections of 5-HT in a flow-injection-cell and compared the current drop from the first to the last injection. The 5-HT responses were compared to dopamine (DA), a neurochemical that is known to produce minimal fouling oxidative byproducts and have a stable repeated response. Physical cleaving of the BDDME yielded a reduction in fouling due to 5-HT compared to the CFME and the femtosecond laser cut BDDME. However, the femtosecond laser cut BDDME exhibited a large increase in sensitivity over the cleaved BDDME. An extended stability analysis was conducted for all device types following 5-HT fouling tests. This analysis demonstrated an improvement in the long-term stability of boron doped diamond over CFMEs, as well as a diminishing sensitivity of the laser cut BDDME over time. This work reports the electrochemical fouling performance of the BDDME when it is repeatedly exposed to DA or 5-HT, which informs the development of a chronic, diamond-based electrochemical sensor for long-term neurotransmitter measurements in vivo.

Low-frequency audible noise generated by the magnetostriction effect inherent to the operation of power transformers has become a major drawback, especially in cases where the electrical substation is located in urban areas subject to strict environmental regulations that imposes sound pressure limits, differing for day and night periods. Such regulations apply a +5 dB penalty if a tonal component of noise is present, which is clearly the case of magnetostriction noise, typically concentrated at twice the industrial frequency (50 Hz or 60 Hz, depending on the country). The strategy used to eliminate the tonal characteristics, therefore contributing to establish compliance with the applicable regulation and to alleviate the discomfort it causes to the human ear, consisted in superimposing to the substation noise a masking sound synthesized from “sounds of nature” with suitable intensities, to flatten the noise spectrum while enhancing the soundscape. The masking system (heavy-duty speakers powered by a microprocessor platform) was validated at an already judicialized urban scenario. Measurement results confirmed that the masking solution was capable of flattening the tonal frequencies, whose beneficial effect yielded the cancellation of the public civil action filed by the neighbors. The proposed solution is ready to be replicated to other scenarios.

Due to the long-term deformation settlement of foundations, issues such as damage and functional failure of buildings and structures have long been of concern in the engineering field. The creep of soil is one of the primary causes leading to long-term deformation of foundations. In this paper, the consolidation deformation, creep characteristics, and creep model of reconstituted saturated silty clay were studied by isotropic compression test and triaxial shear creep test. The results show that for the isotropic compression test, although the applied load adopts different stages of loading, as long as the final applied confining pressure is the same, the number of stages applied by the confining pressure has little effect on the final isotropic consolidation deformation of the sample and the triaxial undrained shear strength after creep. However, for the triaxial shear creep test, it is found that under the same final deviatoric stress, the final deviatoric strain of the sample is closely related to the number of loading stages of deviatoric stress. It shows that the more loading stages of the sample loaded with the same deviatoric stress, the smaller the final deviatoric strain, and the triaxial undrained shear strength of the sample after creep will increase. In addition, it is reasonable to determine the pore pressure dissipation of the sample to 95%((u0-u0)/u0=95%) as the main consolidation end time (tEOP) of the sample. The isotropic consolidation creep curves and the triaxial shear creep curves show certain nonlinearity. Then the logarithmic model and the hyperbolic model were used to fit the creep curves of the samples. It is found that the hyperbolic model has a better fitting effect than the logarithmic model, but for the triaxial shear creep test, the creep parameters of the sample change greatly. Therefore, studying the creep characteristics of soil under different pre-loading steps is of significant engineering importance for evaluating the long-term deformation of underground structures.

In this paper, spacetime is defined as the absolutely invariant homogeneous "coordinate spacetime" frame and its modulation by the relatively variable non-homogeneous "metric spacetime" under its constraints. This modulation is caused by matter and motion, and carries the function of transmitting interactions, reflecting the diffeomorphism invariance and Lorentz invariance. This inhomogeneous spacetime concept makes the medium nature of spacetime more obvious and avoids the problem of "path dependence" caused by the concept of curved spacetime. In this paper, it is argued that all energy-momentum has internal spatio-temporal properties, and all interactions must be transmitted through spacetime metrics. On this basis, a converging and dispersing cyclic multiverse model is proposed. This model of the universe is inevitable as long as there are two macroscopic manifestations of the matter of the universe, namely, gravitation induced convergence and "explosive" dispersion caused by different factors. The new cosmic model matches the observed accelerated "expansion" of the universe and no longer requires the dark energy hypothesis.

There is a growing interest in the endocannabinoid system and the gut microbiota. Both areas have been suggested to play a role in endometriosis, however this is yet to be studied comprehensively. The purpose of this narrative review is to identify the gaps in endometriosis research in the context of these two areas. It underscores the limited knowledge regarding the involvement of the endocannabinoid system and gut microbiota in endometriosis. Further research in these areas is essential to unlock the therapeutic potential of cannabis and enhance the understanding of endometriosis pathogenesis.

Plastics, once regarded as a revolutionary material shaping modern society, now poses an unprecedented threat to our environment. Household solid waste sorting stations produce several fractions, one of which contains a high concentration of Low-Density Polyethylene (LDPE) film waste (packaging, sunscreen film, etc.). This fraction is difficult to recycle because it contains quite a lot of impurities. Usually, it is sent to the cement factories that burn it together with other fuels. However, with some processing techniques such catalytic pyrolysis this fraction could be valorized. In this paper the experiments which were carried out at a laboratory scale installation, in batches with a processing capacity of 1-3 kg of waste. The pyrolysis reactor is connected to a distillation column giving the possibility to separate the fractions. The gaseous and liquid fractions were characterized by GC-FID-TCD (gases) and GC-MS (liquids) analysis. Natural catalysts such as bentonite or clinoptilolite were studied and used in the melting of plastic mass to simplify the process as much as possible. To test the activity of the catalysts, the pyrolysis of LDPE granules was initially studied. It was found that natural zeolites are much more active than bentonite and that a minimum concentration of 5-10% is needed to have a positive effect on the composition of the fractions (increasing the weight of the light fractions C1-C6, C6-C10 and C11-C13) in relation to the heavy fractions C13-C20 and C20+. Catalytic pyrolysis gives a completely different distribution of light hydrocarbons. The best catalyst selected from LDPE lab experiments, was then tested upon the pyrolysis of plastic film waste obtained by a waste treatment plant. The research objective reported in this paper was to obtain a fraction of combustible gases in the largest possible proportion, which can be much easier exploited by burning in an engine that drives an electric generator.

Strain-hardening cement-based composites (SHCC) are a novel class of fiber-reinforced concretes which exhibit high tensile strain capacity prior to failure localization. Although the tensile behavior of SHCC has been a matter of study in numerous research works, the behavior of these composites under other loading modes has scarcely been investigated. The article at hand addresses the mechanical behavior of two types of normal-strength SHCC subject to uniaxial tension, torsion, and combinations of torsional and axial loading. The SHCC under investigation were made with polyvinyl-alcohol (PVA) and ultra-high molecular weight polyethylene (UHMWPE) fibers, respectively. Digital Image Correlation (DIC) was applied to evaluate the multiple cracking process and crack opening modes in conjunction with the concretes’ axial and torsional loading histories. The study demonstrates the suitability of torsion experiments to assess the multi-axial and shear performance of SHCC, highlights the relation between multiple cracking and transfer capacity for shear forces, and emphasizes the importance of the type of reinforcing fibers on the shear strength and ductility of such composites.

Ambient vibration energy is widely being harnessed as a source of electrical energy to drive low-power devices. The vibration energy harvester (VEH) of interest employs an electromagnetic transduction mechanism, whereby ambient mechanical vibration is converted to electrical energy. The limitations affecting the performance of VEHs, with an electromagnetic transduction structure, include its operational bandwidth as well as the enclosure-size constraint. In this study, an analysis and design of a nonlinear VEH system is conducted, using the Output Frequency Response Function (OFRF) representations of the actual system model. However, the OFRF representations are determined from the Generalised Associated Linear Equation (GALE) decompositions of the system of interest. The effect of both nonlinear damping and stiffness characteristics, to respectively extend the average power and operational bandwidth of the VEH device, is demonstrated.

This study mainly experimentally investigates and explores the effects of local low-frequency vibrations on the starting-up and heat transfer characteristics of the pulsating heat pipe. A micro motors with the vibration frequency of 200 Hz were imposed on the external surface of evaporation, condensation and adiabatic section of the pulsating heat pipe, respectively, and the starting-up temperature and the average temperatures along the evaporation section as well as the thermal performances of the vibrating heat pipe were experimentally scrutinized under the local vibrations of different positions. The following important conclusions can be achieved by the experimental study: 1) The effect of vibrations at the evaporation section and at the adiabatic section on the starting-up time of pulsating heat pipe is more significant than that at the condensation section. 2) The vibrations at different positions can reduce the starting-up temperature of the pulsating heat pipe. The effect of the vibrations at the evaporation section is the best as the heating power is lower, and the effect of the vibration at the adiabatic section is the best as the heating power is higher. 3) The vibrations at the evaporation section and at the adiabatic section can reduce the thermal resistance of the pulsating heat pipe. However, the vibrations at the condensation section have little effect on the thermal resistance of the pulsating heat pipe. 4) The vibrations at the evaporation section and at the adiabatic section can effectively reduce the temperature of evaporation section of the pulsating heat pipe, but the vibrations at the condensation section have no effect on the temperature of evaporation section of the pulsating heat pipe.

Hybrid reinforcement in a composite material (CM), in many situations, allows better govern material mechanical properties. Polymer matrix CM plate is reinforced with small particles and macro-fibers. Particles are oil shale ash (OSA) powder, macro-fibers – basalt fiber threads im-pregnated by matrix material. With the goal to find out elastic properties of the matrix- polymer with OSA, samples with its different concentrations were experimentally fabricated and their elastic properties were experimentally measured. Obtained data were used in numerical model-ling. Was observed polymer matrix composite slab, reinforced with OSA and three-dimensional (3D) basalt fiber fabric. Fabric are forming threads impregnated by matrix (polymer resin mixed with OSA particles). Damage accumulation in the stretched slab was modelled. Impregnated thread, in the modelling, is observed as a macro-fiber (MF) with averaged elastic properties. With the load increase MF in the material began to break. At first, appeared isolated single breaks. A probabilistic sequential MF rupture accumulation model was accepted and numerical-ly realized. The geometry of the reinforcing knitted fabric was modeled using the Leaf and Glaskin approach. In the knitted fabric highly, stressed MF cross-sections are observed as po-tential location where thread breakage can occur. If one thread breaks, the cross-sections of the adjacent threads experience the overload caused by this rupture. More overloaded crossection in the adjacent overloaded thread breaks and we obtain two adjacent broken MF designated as a defect with the size j=2. The probabilities of obtaining defect consisting of at least 2, 3, … j adjacent broken MF in the plate were calculated. The calculations continued until the rupture process becomes unstable (j→∞). The overstresses on adjacent threads in the CM were calculat-ed using the FEM three-dimensional numerical approach. Analytical and stochastic methods were used for the load-carrying capacity determination and different size defects accumulation in the hybrid composite material (HCM) plate. Also, was calculated the probability of the plate rupture.

In this research paper, design and development of pyramidal horn antenna for J-band application is reported. It is particularly designed for 17 dB gain and half beam width about 25 degrees at 6.93 GHz. Horn aperture, horn axial length and distance from the throat of the antenna to aperture are the main design constraints which are calculated and used for the antenna design and simulation. Beam width in E-plane and H-plane horn is calculated and it is 19.18 dB and 22.86 dB respectively. The reported antenna design shows good performance for J-band in radiometry, satellite, and radar applications.

The heat release response of the flame to acoustic excitation is a critical factor for understanding combustion instability. In the present work, the nonlinear heat release response of a methane-air non-premixed flame to the low frequency acoustic excitations is experimentally investigated. The flame describing function (FDF) was measured based on the overall CH* chemiluminescence intensity and the velocity fluctuations obtained by two-microphone method. The CH* chemiluminescence images and the schlieren images were analyzed to reveal the mechanism of nonlinear response. The excitation frequency ranges from 10Hz to 120Hz. The forced relative velocity fluctuation amplitude ranges from 0.10 to 0.50. The corresponding flame Strouhal number (Stf) ranges from 0.43 to 4.67. The study has shown that the flame length responds more sensitively to changes in excitation amplitude when subjected to relatively high frequency excitations. The normalized flame length (Lf/D) decreases from 3.79 to 2.37 with the increase of excitation amplitude at excitation frequency of 100Hz. The number of oscillation zones along the flame increases with increasing excitation frequency, which is consistent with the increase of the Stf. The low-pass filtering characteristic of FDF is caused by the dispersion of multiple oscillation zones, as well as the cancellation effect of the adjacent oscillation zones under relatively high frequency excitation. The cancellation effect of the positive and negative oscillation zones with various Stf is main mechanism for the local gain peak and valley. When two adjacent oscillation regions have approximate amplitudes, the overall phase-lag becomes more sensitive to changes in excitation frequency and amplitude. This sensitivity leads to nonlinear anomalous changes in the phase-lag near the frequency corresponding to the gain valley. The calculated disturbance convection time is consistent with the measured time delay in the short flame scenario. Future research is necessary to establish whether the observed agreement occurs due to the oscillation zone consistently occurring proximate to the flame's center of mass, coupled with a precise determination of the average convective velocity.

Extremely low-frequency electromagnetic fields (ELF-EMFs) are non-ionizing radiations typically emitted by power lines, electrical wiring and electrical appliances. Epidemiological studies have repeatedly shown a positive association between ELF-EMFs and childhood leukemia. Exposures greater than 0.3-0.4 µT increase the risk by approximately 1.5-2 fold, and estimates indicate that up to 2% of childhood leukemia cases in Europe may be attributable to ELF-EMFs. However, it is considered unlikely that ELF-EMFs can cause cancer, because carcinogenesis requires the accumulation of DNA alterations and ELF-EMFs do not have enough energy to damage the DNA. Lack of biological plausibility is a barrier to accept the evidence of carcinogenicity in human studies and to take measures to protect pregnant women and children from ELF-EMFs. Recent evidence indicates that non-mutagenic agents can cause DNA alterations and increase the risk of cancer by promoting the accumulation of cell divisions in stem cells. Cell division generates DNA alterations (e.g., mutations arising during DNA replication), which occur even in the absence of DNA-damaging agents. Importantly, ELF-EMFs can trigger the division of stem cells; this effect is under development in the field of regenerative medicine. A possible mechanism by which ELF-EMFs induce the malignant transformation of hematopoietic stem cells is discussed.

The aims of the study are: a) Describe the reactogenicity of WHO-approved two mRNA (Pfizer-BioNTech, Moderna) and two non-RNA vaccines (Oxford-AstraZeneca, Sinovac) among lactating mother and baby pairs; and b) compare and contrast the reactogenicity between mRNA and non-mRNA vaccines. A cross-sectional, self-reported survey was conducted amongst 1784 lactating women who received COVID-19 vaccinations. The most common maternal adverse reaction was a local reaction at the injection site; the largest minority of respondents, 43.7% (780/1784), reported experiencing worse symptoms when receiving the second dose compared to the first dose. There were no major reported adverse effects or behavioural changes in the breastfed infants. Among the respondents who received non-mRNA COVID-19 vaccinations, a majority reported no change in lactation but those who did more commonly reported an increase in milk supply, decrease in milk supply and pain in the breast. The more commonly reported lactation changes (fluctuations in breastmilk supply and pain in the breast) for the non-mRNA vaccines were similar to that of respondents who received mRNA vaccines. Our study, with a large cohort and wide geographical and racial mix, further augments earlier reported findings that COVID-19 vaccines are safe for breastfeeding mothers and her children.

This study uses a mass-spring-damping system to simulate the repeated strain of liquefaction cyclic triaxial tests. The two results are compared in this paper to understand the feasibility of the mass-spring-damping system developed in this paper and the feasibility of future research on this related topic and development potential. The main factors affecting this mode's repeated strain are the spring coefficient k and the external force Q0. The spring coefficient has an inverse relationship but does not increase in multiples. The external force has a direct proportional relationship but does not increase the result- a non-multiple increase. When the pore water pressure of the liquefied cyclic triaxial test specimen rises, it will cause the specimen to liquefy, decreasing effective stress, shear modulus G, and damping ratio D, causing an increase in strain. The shear modulus and damping ratio are related to the spring coefficients k and c. Both are variables that change with time. This article takes an original thin-tube specimen at point A in the Yunlin area in Taiwan as a testing example. Through Mathematica software, it can be obtained that the mass m=1kg, the spring coefficient k=244e-0.1t kgf/cm, and the damping coefficient c=0.739e-0.257t kgf-s/cm and external force Q0=10.1sin2πt kg; Finally, this study selected the original thin-tube specimens from four locations in the Yunlin area, and simulated the repeated strain amount of the cyclic triaxial test specimens through a spring-damping system. The results show that the spring-damping system is feasible for simulated cyclic triaxial tests because the model is simple and the parameters are easy to understand and obtain, which also shows the extensibility of this model. Preliminary results of the research show that this model can further simulate the repeated strain obtained by cyclic triaxial tests without considering the increased trend in pore water pressure and the decrease in effective stress during cyclic loading.

Weak signal spectral detection is a serious problem in many applications, especially the target possesses certain frequency band and under low signal-to-noise ratio (SNR). A kind of novel technique based on pre-whitening scale-transformation symmetric bistable parallel stochastic resonance (SR) is proposed to solve the problem. Firstly, the pre-whitening can ensure the even distribution of the receiving signal to fit the requirement of SR processing. Secondly, the scale- transformation can help to utilize the weak signal improvement property especially under low frequency band more effectively. Thirdly, the symmetric bistable parallel SR can try to reduce the variance of the clutter and additive noise fluently. Fourthly, by subtracting the steady state re-sponse of the selected symmetric bistable SR system from the parallel SR output, the weak signal spectral detection objective can be realized successfully. Simulation results based on the real sea clutter radar data guarantee the effectiveness and applicability of the proposed symmetric bistable PSR processing approach.

Metal-reinforced polymethyl-methacrylate (PMMA) is considered the gold standard material for immediate loading on dental implants. However, mechanical problems under loading cycles can occur, such as fractures. To overcome these drawbacks, a novel polymer-based material has been proposed. The aim of the present in vitro comparative research is to validate a novel composite polymer developed to replace metal-reinforced PMMA interim restoration due to its advantages of good mechanical proprieties, easier manufacturing, and handling. Ten interim restorations were CAD/CAM designed and fabricated (five in the composite "ONLY" group, and five in the metal-reinforced PMMA group). All the samples were screwed into the prototype models, simulating a complete edentulous mandible rehabilitated with six straight implants. Outcome measures were breakpoint (load, N) and displacement (mm) thought a static, compression test and material behavior under dynamic cyclic test method (fatigue test). A total of twenty samples were tested. Ten samples were used for each test (10 for static and 10 for dynamic), five samples were used in each group (test and control). All the specimens completed the mechanical tests, as planned. There was no statistically significant difference between groups for all, breakpoint, displacement and fatigue tests. Breakpoint in the test group was 1953.19 ± 543.73 N, while, it was 2031.10 ± 716.68 N in the control group, with no statistically significant difference (P=0.775). The displacement was 1.89 ± 0.34 mm in the test group and 1.98 ± 0.75 mm in the control group, again, with no statistically significant difference (P=0.763). Under dynamic cyclic test method, in the control group the mean load was 2504.6 ± 972.15 N, while, in the test group the mean load was 3382 ± 578.5 N. The difference between group was 877.4 ± 579.3 N (p value=0.121). With the limitation of this in vitro study, the novel composite polymer can be used to immediately load dental implants. Further clinical researches are needed to confirm this preliminary results.

Steel fibre reinforced concrete (SFRC) consists of short hooked steel fibres randomly distributed and oriented within the cementitious matrix. The contribution of fibre in bridging cracks to provide the stress transfer required relies upon the orientation of the fibre in the concrete. Bridging fibre aligned with a crack are less effective than those inclined to it. Therefore, understanding the pull-out behaviour of misaligned fibre is a key factor to quantify and optimize the design of SFRC in the structural applications. In the laboratory a single oriented fibre embedded in a solid cylinder of concrete is subjected to a pull-out test where the axis of a tensile force is aligned with the axis of the cylinder. Based upon the observed behaviour this paper presents a new analytical bounding approach to capture the pull-out response of misaligned hooked-end steel fibre embedded in a concrete matrix. The analysis is based upon a transversely isotropic condition assumed for the plasticity that occurs in the cold drawn fibre. The model accounts for the influence of fibre diameter and the combined strengths of the steel and concrete. The model predictions have also been compared with other experimental results published in the literature. The results showed that the model can predict pull-out loads reasonably for different fibre orientations between bounds of failure derived from the strengths of the two constituents. A critical orientation is observed at maximum strength. Therein, an understanding of the pull-out behaviour of misaligned, hooked-end fibres is necessary to optimize the strength of concrete from this method of reinforcement.

The problem of intensification of melt crystal growth process has been analyzed using CdTe as an actual material. Numerical simulation of 100 mm diameter CdTe crystal growth by VGF technique has been carried out. The heat-mass transfer was controlled by introducing of low-frequency oscillating baffle into the melt, so called axial vibrational control (AVC) technique. The baffle configuration has been optimized to destroy solid «tails», which were formed near the crucible walls at high cooling rates due to the low thermoconductivity and the corresponding latent heat. Analysis of CdTe homogeneity range showed that during fast crystal cooling Te micro precipitations were formed resulting from decay of oversaturated Cd-riched nonstoichiometric solid solution at Bridgman crystal growth technique. A VGF grown CdTe crystal after full crystallization stays inside the phase field of the high temperature wurtzite polymorph. This makes it possible to go through the polymorph transition without Te micro-precipitating using the advantages of VGF specific feature of very slow cooling.

Manipulation of radiation pattern control is challenging, especially at low frequencies. In this paper, we demonstrate that acoustic metamaterials as an effective array of quadrupoles can remarkably improve the directionality of acoustic radiation at low frequencies, compared with previous metamaterials as monopole and dipole structures. The directivity of the acoustic radiation can be adjusted by changing the characteristic parameter and the symmetry of the structure, which provide a flexible method of adjustable radiation di-rections. The directionality can be further improved by constructing linear array of structure. Our work opens an approach of acoustic radiation control via quadrupolar metamaterials.

Macrophages undergo different cellular states upon activation that can be hyporesponsive (tolerated) or hyperresponsive (primed or trained) to subsequent stimuli. Epigenetic modifications are known to play a key role in determining these cellular states. However, little is known about the role of signaling pathways that lead to these epigenetic modifications. Here, we examined the effects of various inhibitors targeting key signaling pathways induced by lipopolysaccharide (LPS) on tolerance and priming in the murine macrophages. We found that a prolonged inhibition (>18 h) of the MEK1/2-ERK signaling axis reversed tolerance and primed cells in expressing IL-1β and other inflammatory cytokines such as IL-6, TNFα, and CXCL10. Ectopic expression of catalytically active and inactive MEK1 mutants suppressed and enhanced IL-1β expression, respectively. Primed cells by the MEK1/2 inhibitor U0126 expressed higher levels of gene sets associated with immune responses and cytokine/chemokine production but lower levels of genes with cell cycle progression, chromosome organization, and heterochromatin formation than non-primed cells. Of interest, expression of the histone 3 lysine 9 (H3K9) methyltransferase Suv39h1 and the H3K9 methylation reader Cbx5 was substantially suppressed, whereas the H3K9 demethylase Kdm7a was enhanced, suggesting a role of the MEK1/2-ERK signaling axis in H3K9 demethylation. The H3K9 trimethylation levels in the genomic regions of IL-1β, TNFα, and CXCL10 were decreased by U0126. Also, the H3K9 methyltransferase inhibitor BIX01294 mimicked and overexpression of Cbx5 prevented the U0126 training effects in both RAW264.7 cells and bone marrow-derived macrophages. Collectively, these data suggest that prolonged inhibition of the MEK1/2-ERK signaling axis reverses tolerance and primed macrophages likely through decreasing H3K9 methylation levels.

This letter presents a dual-frequency terahertz amplitude modulator based on a cross-shaped structure and U-shaped metal patches. Its structural unit is a typical metal-substrate structure. The top metal consists of a cross-shaped structure and U-shaped metal patches, and the bottom substrate layer is made of quartz. Amplitude modulation is achieved by adjusting the temperature of the vanadium dioxide (VO2) patches. The modulation depth can be approximately 75%. The mechanism of the resonance frequency is explained by the equivalent circuit model. The proposed structure shows good amplitude modulation capability at different incidence and azimuth angles by changing the location of the VO2 patches. The dual-frequency terahertz amplitude modulator can be used in terahertz communication, imaging, etc.

Tinnitus is a common phantom auditory percept, believed to be related to plastic changes in the brain due to hearing loss. However, tinnitus can also occur in absence of any clinical hearing loss. Then, since there is no hearing loss, the mechanisms that drive plastic changes remain largely enigmatic. Previous studies showed subtle differences in sound-evoked brain activity associated with tinnitus in subjects with tinnitus and otherwise, normal hearing, but the results are not consistent across studies. Here, we aim to investigate those differences using monaural rather than binaural stimuli. Sound-evoked responses were measured using functional magnetic resonance imaging (MRI) in participants with and without tinnitus. All participants had clinically normal audiograms. The stimuli were pure tones with frequencies between 353 and 8000 Hz, presented monaurally. A Principal Component Analysis (PCA) of the response in the auditory cortex revealed no difference in tonotopic organization, which confirmed earlier studies. A GLM analysis showed hyperactivity in the lateral areas of the bilateral auditory cortex. Consistent with the tonotopic map, this hyperactivity mainly occurred in response to low stimulus frequencies. This may be related to hyperacusis, which was associated with tinnitus found in the parahippocampus. This may reflect an interference between tinnitus and spatial orientation.

The implementation of sentinel lymph node (SLN) biopsy is changing the scenario in the surgical treatment of early-stage cervical cancer and the oncologic safety of replacing bilateral pelvic lymphadenectomy with SLN biopsy is currently under investigation. One of the undisputed values of SLN biopsy is its diagnostic accuracy in detecting low-volume metastases (LVM) via pathologic ultrastaging. In early-stage cervical cancer, the reported incidence of LVM ranges from 4 to 20%. The prognostic impact and the role of adjuvant treatment in patients with LVM is still unclear. Some non-prespecified analyses in prospective studies showed no impact on the oncologic outcomes compared to node-negative disease. However, the heterogeneity of the studies, the differences in the disease stage and the use of adjuvant treatment, and the concomitant pelvic lymphadenectomy (PLND) make any conclusion on this topic hard. Current guidelines suggest considering micrometastasis (MIC) as a node-positive disease, while isolated tumor cells (ITC) as a node-negative disease, with a low level of evidence. This review aims to highlight the unanswered questions about the definition, identification, prognostic and therapeutic role of LVM and underline the present and future challenges we are facing. We hope this review will guide further research, giving robust evidence on LVM and their impact on clinical practice.

Antimicrobial peptides (AMPs) are promising tools for combating microbial resistance. However, their therapeutic potential is hindered by two intrinsic drawbacks – low target affinity and poor in vivo stability. Macrocyclization, a process that improves the pharmacological properties and bioactivity of peptides, can address these limitations. As a result, macrocyclic peptides represent attractive drug candidates. Moreover, many drugs are macrocycles that originated from natural product scaffolds, suggesting that nature offers solutions to the challenges faced by AMPs. In this review, we explore natural cyclic peptides from the DBAASP database. DBAASP is a comprehensive repository of data on antimicrobial/cytotoxic activities and structures of peptides. We analyze the data on small (≤25 AA) ribosomal and non-ribosomal cyclic peptides from DBAASP according to their amino acid composition, bonds used for cyclization, targets they act on, and mechanisms of action. This analysis will enhance our understanding of the small cyclic peptides that nature has provided to defend living organisms.

To improve carbon efficiency for urban logistics service system composed of a third-party logistics service provider (3PLs) and an e-business enterprise, low-carbon operation game between them was studied. Considering low carbon technology investment cost and sales expansion effect of low carbon level, profit functions for both players were constituted. Based on their different bargaining capabilities, totally 5 types of game scenarios were designed. Through analytical solution, Nash Equilibria under varied scenarios were obtained. By analyzing these equilibria, 4 major propositions were given, in which, some key variables and system performance index were compared. Results show that the best system yields could only be achieved under the fully cooperative situation; limited cooperation only for carbon emission reduction would not benefit the system performance improvement; E-business enterprise-leading game’s performance overtook 3PLs-leading ones.

There have been a great number of investigations about the influence of weak magnetic fields on biological systems, such as isolated cells and whole organisms. This is also a subject of considerable medical concern since old epidemiologic observations have indicated a possible tumorigenic effect of these fields. Their mechanism of action, however, is not firmly established. A large number of biological effects of electromagnetic fields have been attributed either to the production of reactive oxygen species (ROS) or to the entrance Ca²⁺ in the cell. A new biochemical pathway is proposed that covers these two possibilities: the primary effect of the magnetic field would be by the mechanism of radical pairs resulting in the production of ROS; these could activate the ion channels TRPM2 producing cellular inflow of Ca²⁺, which would induce the calcium dependent effects. Thus, a large number of biological effects observed up to the present could be explained.

The application of the sensors optical fiber in the areas of scientific instrumentation and industrial instrumentation is very attractive due to its numerous advantages. In the industry of civil engineering for example, quasi-distributed sensors made with optical fiber are used for reliable strain and temperature measurements. Here, a quasi-distributed sensor in the frequency domain is discussed. The sensor consists of a series of low-finesse Fabry-Perot interferometers where each Fabry-Perot interferometer acts as a local sensor. Fabry-Perot interferometers are formed by pairs of identical low reflective Bragg gratings imprinted in a single mode fiber. All interferometer sensors have different cavity length, provoking the frequency-domain multiplexing. The optical signal represents the superposition of all interference patterns which can be decomposed using the Fourier transform. The frequency spectrum is analyzed and sensor´s properties were defined. Following, a quasi-distributed sensor was numerically simulated. Our sensor simulation considers sensor properties, signal processing, noise system and instrumentation. The numerical results show the behavior of resolution vs. signal-to-noise ratio. From our results, the Fabry-Perot sensor has high resolution and low resolutions. Both resolutions are conceivable because the FDPA algorithm elaborates two evaluations of Bragg wavelength shift

Models of subsurface structures are important for successful deposit exploration but are challenged by the need to integrate data from different geophysical methods. In the present study, we evaluated a method of joint inversion in which audio-magnetotelluric (AMT) and dual frequency induced polarization (DFIP) data sets are inverted simultaneously to produce a consistent 2D resistivity model to show a clear image of subsurface structures. To achieve the objectives, we conducted AMT and DFIP surveys first on the same survey line within the Dongjun lead-zinc deposit in inner Mongolia by developing 31 AMT survey sites with an interstation separation of 40 m on a 1440 m survey track and operated in fifty-three frequencies in the range 1–10,400 Hz to record the resistivity distribution of subsurface to depths exceeding 800 m. The same survey setup up was applied to the DFIP method by utilizing the SQ-3C model with a pole-dipole array configuration and conducted measurements at frequencies of 4 Hz and 4/13 Hz. We first separately inverted AMT and DFIP measurements. The two-dimensional (2D) model obtained from AMT data revealed distinct low resistivity anomalies in the middle of the 2D inversion model. In contrast, the DFIP inversion model showed a high resistive body in the same region. In response to the discrepancies observed in the separate 2D inversion models, we implemented a joint inversion for both the AMT and DFIP datasets. The joint inversion resistivity model shows surficial conducting bodies and a high conductive body along the profile with relatively high Percent Frequency Effect (PEF) indicating high chargeability. The final joint inversion resistivity model clearly images the large silica alteration zone and the Pb-Zn mineralization. This study demonstrates the feasibility of a joint inversion methodology and highlights the value of integrating geophysical methods through joint inversion for enhanced characterization and exploration of lead-zinc ores.

In order to further control the equivalent circulating density,a new type of annular pres-sure-reducing downhole tool for high temperature and high pressure wells-liquid-absorbing ECD tool is designed.Through this tool,the bottom hole pressure of the equivalent circulating drilling fluid can be close to its hydrostatic pres-sure,therebyachieving a deeper drilling depth.The tool is mainly composed of screw mo-tor,vortex blade,annular seal,universal joint and drill string.Its working principle is mainly to use the liquid absorption effect of the tool and the hydraulic energy of the circu-lating fluid extracted by the screw motor to convert it into mechanical energy,and to gen-erate suction force to improve the flow energy of the drilling fluid in the bottom hole an-nulusand reduce the equivalent circulation density.Based on ANSYS-FLUENT analysis andsimulation,the change of pressure drop characteristics under different drilling fluid density,displacement and tool size was simulated.The simulation results show that thedepressurization effect is 1.0MPa when the drilling fluid density is 1.2g/cm3. When the drilling fluid density is 1.5g/cm3,the depressurization is about 1.7MPa,and when thedrill-ing fluid density is 1.8g/cm3,the depressurization is about 1.9MPa.When the drilling fluid density is 2.0g/cm3,the pressure drop is about 2.3MPa.When the flow rate is from 1500-2500L/min,the maximum pressure can be reduced by 2.3MPa.When the viscosity is 40mPa•S and 60mPa•S,the pressure drop almost does not change.The increase of viscosi-ty has little effect on the pressure drop,and it is mainly affected by the flow rate under equal displacement.

Despite the fact that COVID-19 treatment and management are now considerably regulated, SARS-CoV-2 is still one of the leading causes of death in 2022. The availability of COVID-19 vaccines, FDA-approved antivirals, and monoclonal antibodies in low-income countries still poses an issue to be addressed. Natural products, particularly traditional Chinese medicines (TCMs) and medicinal plant extracts (or their active component) have challenged the dominance of drug repurposing and synthetic compound libraries in COVID-19 therapeutics. Abundant resources and excellent antiviral performance make natural products a relatively cheap and easily available alternative for COVID-19 therapeutics. Here, we deliberately review the anti-SARS-CoV-2 mechanisms of the natural products, their potency (pharmacological profiles), and application strategies for COVID-19 intervention. In light of their advantages, this review is intended to acknowledge the potential of natural products as COVID-19 therapeutic candidates.

In this work, an analog front-end (AFE) circuit for Electrocardiogram (ECG) detection system has been designed, implemented, and investigated in an industry-standard Cadence simulation framework using advanced technology node of 45 nm. The AFE consists of an instrumentation amplifier, a Butterworth band-pass filter (with fifth-order low-pass and second-order high-pass sections), and a second-order notch filter- all are based on two-stage, Miller-compensated operational transconductance amplifiers (OTA). The OTAs have been designed employing the $g_m/I_D$ methodology. Both the pre-layout and post-layout simulation were carried out. The layout consumes an area of 0.0058 mm$^2$ without the resistors and capacitors. Analysis of various simulation results were carried out for the proposed AFE. The circuit demonstrates a post-layout bandwidth of 239 Hz with a variable gain between 44 to 58 dB, a notch depth of -56.4 dB at 50.1 Hz, a total harmonic distortion (THD) of -59.65 dB (less than 1\%), an input referred noise spectral density of $

Nanostructured dipeptide self-assemblies exhibiting quantum confinement are of great interest due to their potential applications in the field of materials science as optoelectronic materials for energy harvesting devices. Among those, aromatic cyclo-dipeptides containing the amino acid tryptophan are wide-band gap semiconductors displaying high mechanical rigidity, photoluminescence and piezoelectric properties to be used in power generation. In this work, we report the fabrication of hybrid systems based on chiral cyclo-dipeptide L-Tryptophan- L-Tryptophan incorporated into biopolymer electrospun fibers. The micro/nanofibers contain self-assembled nanospheres embedded into the polymer matrix are wide-band gap semiconductors (gap energy 3.8 eV), display blue photoluminescence and relevant piezoelectric and pyroelectric properties with coefficients as high as 57 pCN-1 and 35×10-6 Cm-2k-1, respectively. They are therefore promise systems for thermal sensing and energy harvesting applications.

A novel theoem is presented about a circle with four antipodal points, arbitrarily ordered counterclockwise (or clockwise), in a Euclidean plane.

The regulation of multiple bacterial phenotypes was found to depend on different cyclic di-nucleotides (CDNs) that constitute intracellular signalling second messenger systems. Most notably, c-di-GMP, along with proteins related to its synthesis, sensing and degradation, was identified as playing a central role in the switching from biofilm to planktonic modes of growth. Recently, this world has been under expansion, with the discoveries of other signalling CNDs in bacteria (c-di-AMP and cGAMP) and also in eukaryotes, novel protein and RNA receptors of CDNs, and the numerous functions related to these molecules. In this work, we comprehensively review and analyse the structural biology data about the systems that bacteria use to synthesise and recognise CDNs, detailing their interactions at molecular level with their products/ligands. Additional interesting observations were made, including that different receptor types can bind CDNs in similar conformations and that, based on genomic data, different CDN second messenger systems may coexist in many organisms. The large amount of sequence and structural data available allows a broad view of the importance of CDNs in bacteria, but how cells coordinate these molecules to ensure adaptation to changing environmental conditions is still open for much further exploration.

The paper examines the various uncertainties encountered in high-frequency trading (HFT) environments and delves into the multiple challenges faced by HFT firms in navigating the Dodd-Frank Wall Street Reform and Consumer Protection Act (referred to as the "Dodd-Frank Act"), particularly during the initial stages of its enactment. These challenges include the ambiguity surrounding the definition of HFT, the lack of clarity regarding regulatory requirements and boundaries, inconsistencies in enforcement resulting from deviations in understanding the content, and the absence of detailed descriptions of the Act’s provisions. These hurdles significantly impact not only the daily operations of HFT firms but also pose higher demands on their long-term strategic planning and risk management. Drawing upon the Data, Information, Knowledge, Wisdom, and Purpose (DIKWP) model, this study employs an innovative analytical framework. Through the comprehensive application of conceptual space, cognitive space, and semantic space, it provides a systematic methodology for identifying and analyzing the aforementioned issues. This approach not only aids firms in better comprehending and adhering to complex regulatory requirements but also enables them to explore new business opportunities and competitive advantages while ensuring compliance.

Recurrent pregnancy loss (RPL) affects around 2 % of women of reproductive age. Primary RPL is defined by ≥2 pregnancy losses and no normal birth delivery. In secondary RPL, the losses are after a normal pregnancy and delivery. Most cases have no clear aetiology, although primary cases are the most complex. Several gene polymorphisms have been associated with RPL. Some polymorphisms are increased in women of Asian or Caucasian race. In admixed RPL populations, the information on possible genetic links is scarce and contradictory. The study aimed to assess the frequency of two SNP in different enzymes involved in medical conditions observed during pregnancy. Microsomal epoxy hydrolase (mEPH) is involved in detoxifying xenobiotics. It is present in ovaries, and it is hormonally regulated. The endothelial nitric oxide synthase forms nitric oxide from arginine and is involved in vascular tone. Two SNPs, rs1051740 and rs1799983, were assessed. The study included 26 controls and 63 primary RPL patients. Significant differences were observed in the frequencies of both SNP (p<0.05). The frequency of mutated alleles was higher in patients. Double mutated homozygotes were encountered only in RLP patients (p<0.05). Genetic polymorphisms rs1051740 and rs1799983 may be involved in primary RPL in the Venezuelan admix population. Genetic studies could provide crucial information on the aetiology of primary RPL.

Herein, we present the design technique of a resonant rectifier for piezoelectric (PE) energy harvesting. We propose two diode equivalents to reduce the voltage drop in the rectifier operation, a minuscule-drop-diode equivalent (MDDE) and a low-drop-diode equivalent (LDDE). The diode equivalents are embedded in resonant rectifier integrated circuits (ICs), which use symmetric bias-flip to reduce the power wasted for charging and discharging the internal capacitance of a PE transducer. The self-startup function is supported by synchronously generating control pulses for the bias-flip from the PE transducer. Two resonant rectifier ICs, using both MDDE and LDDE, are fabricated in a 0.18 μm CMOS process and their performances are characterized under external and self-power conditions. Under the external-power condition, the rectifier using LDDE delivers an output power POUT of 564 μW and a rectifier output voltage VRECT of 3.36 V with a power conversion efficiency (PCE) of 90.1%. Under self-power conditions, the rectifier using MDDE delivers a POUT of 288 μW and a VRECT of 2.4 V with a corresponding PCE of 74.6%. The result shows that the power extraction capability of the proposed rectifier is 5.9 and 3.0 times higher than that of a conventional full-bridge rectifier.

Many studies utilize sensors to measure foot plantar pressure and analyze gait patterns, often focusing on assessing weight-bearing symmetry or asymmetry compared to control groups. However, a critical question arises: does the selection of the control group significantly impact study outcomes? Does chronic low back pain affect foot plantar pressure measurements? This experimental study involved 23 participants, including healthy individuals and those without foot disorders but with chronic low back pain. Dynamic foot pressure measurements were conducted using the Ortopiezometr, and data were analyzed using the "Steps" program. Participants were divided into two groups: Group 1 comprised completely healthy individuals, while Group 2 consisted of individuals without foot problems but with moderate chronic low back pain. The findings highlight a prevalence of energy release in the forefoot sensors compared to the hindfoot for both the right and left legs in most cases. Even among healthy volunteers, achieving perfect symmetry in the maximum values on the sensors for the right and left feet was a challenge. Results showed no statistically significant differences in energy released on specific sensors or duration of gait phases between the groups. Essentially, this suggests that foot pressure patterns are comparable between healthy individuals and those with low back pain. The use of sensor-equipped inserts for pedobarographic examinations indicates that, in cases of degenerative changes in the lumbar and sacral spine without accompanying acute pain, gait patterns resemble those of the healthy population.

Low-frequency electron paramagnetic resonance (EPR) is used to extract the EPR parameter A-mid and support the approximate X-band value of g-mid for Ba(Co_yZn_1/3-yTa_2/3)O₃. Although cobalt hyperfine structure for the [+/−1/2> state is often unresolved at X-band or S-band, it is resolved in measurements on this compound. This allows for detailed analysis of the molecular orbital for the [+/−1/2> state, which is often the ground state. Moreover, this work shows that the EPR parameters for Co substituted into Zn compounds gives important insight into the properties of zinc binding sites.

Rapid and accurate detection of road cracks is of great significance for road health monitoring, but currently this work is mainly completed through manual site surveys. Low-altitude UAV remote sensing can obtain images with centimeter or even subcentimeter ground resolution, which provides a new efficient and economical approach for rapid crack detection. Nevertheless, crack detection networks face challenges such as edge blurring and misidentification due to the heterogeneity of road cracks and the complexity of the background. To address these issues, we propose a real-time edge reconstruction crack detection network (ERNet) which adopts multi-level information aggregation to reconstruct crack edges and improve the accuracy of segmentation between the target and background. To capture global dependencies across spatial and channel levels, we propose an efficient bilateral decomposed convolutional attention module (BDAM) that combines depth separable convolution and dilated convolution to capture global dependencies across spatial and channel levels. To enhance the accuracy of crack detection, we use a coordinate-based fusion module that integrates spatial, semantic, and edge reconstruction information. In addition, we propose an automatic measurement of crack information for extracting the crack trunk and its corresponding length and width. Experimental results demonstrate that our network achieves the best balance between accuracy and inference speed.

Many fields of human activity benefit from the ability to create images of obscured objects placed behind walls and to map their displacement in a noninvasive way. Usually, imaging devices like Synthetic Aperture Radars (SAR) and Ground Penetrating Radars (GPR) use expensive dedicated electronics which results in prohibitive prices. This paper presents the experimental implementation and the results obtained from an imaging system capable of performing SAR imaging and interferometric displacement mapping of targets located behind walls, as well as 3D GPR imaging using a low-cost general-purpose radar sensor. The proposed solution uses for the RF section of the system a K-band microwave radar sensor module implementing Frequency Modulated Continuous Wave operation. The low-cost sensor was originally intended for simple presence detection and ranging for domestic applications. The proposed system was tested in several scenarios and proved to operate as intended for a fraction of the cost of a commercial imaging device.

Frequently Asked Questions (FAQs) systems rely on semantic symmetry similarity measuring between two sentences. To address the challenges of insufficient training data and limited domain-specific understanding in low-resource FAQs, this paper proposes a general framework, PDAMF-FAQ, to solve these issues. Firstly, we propose a paraphrasing-based data augmentation model that integrates syntactic information and edit vectors. Using a rule-based approach, it retrieves template sentences from a corpus and masks relevant words with special characters. Edit vectors between the original and paraphrase sentences are added to a pre-trained model's encoding layer to enhance the model's ability to learn the differences between the original and reference paraphrase sentences. Additionally, this paper presents a mixed-feature semantic matching model based on SimBERT. The model extracts keyword features from the text, replacing these keywords with special characters to construct intent features. These intent features, along with the user question and keyword features, are then concatenated to form the model's input. Experiments were conducted respectively on the paraphrasing-based data augmentation model, mixed-feature semantic matching model and their comprehensive application in a low-resource domain-specific FAQ. The experimental results show that the proposed framework effectively improve the performance of domain-specific FAQ system.

Cyclic neutropenia is a rare hematological condition characterized by periodic fluctuations in neutrophil counts, with a 21-day periodicity. Clinical presentation varies from mild to severe forms of the disease, with the onset of recurrent fever, painful oral ulcers, recurrent bacterial infections, peritonitis and septic shock. The availability of granulocyte colony-stimulating factor (G-CSF) has revolutionized the management and natural history of this disease, regulating the proliferation, differentiation and maturation of the progenitor cells, reducing the duration of neutropenia. Inflammatory bowel disease (IBD), including Crohn’s disease (CD) and ulcerative colitis (UC), is a group of chronic pathologies with involvement of the gastrointestinal tract. Symptoms include diarrhea, abdominal pain, fever, weight loss and extraintestinal manifestations (EIMs). In recent years, the focus of IBD therapy, including conventional therapies and biological therapies, has moved from treatment of symptoms to "deep remission" of the disease. The association between cyclic neutropenia and CD is rarely reported in the literature. Here, we describe two case reports of patients who underwent surgery because of diagnosis of complicated CD. After surgery, because of persistent neutropenia, the hematologist consultant confirmed suspicions of cyclic neutropenia and therapy with G-CSF was started with benefits, underlining the crucial importance of proper differential diagnosis.

This letter introduces a frequency response characteristic (FRC) curve and its application in high renewable power systems. In addition, the letter presents a method for fast frequency response assessment and frequency nadir prediction without performing dynamic simulations using detailed models. The proposed FRC curve and fast frequency response assessment method are useful for operators to understand frequency response performance of high renewable systems in real time.

Cellular response to mechanical stimuli is a crucial factor for maintaining cell homeostasis. The interaction between extracellular matrix and mechanical stress plays a significant role in organ-izing the cytoskeleton and aligning cells. Tools that apply mechanical forces to cells and tissues, as well as those capable of measuring the mechanical properties of biological cells, have greatly contributed to our understanding of fundamental mechanobiology. These tools have been exten-sively employed to unveil the substantial influence of mechanical cues on the development and progression of various diseases. In this report, we present an economical and high-performance uniaxial cell stretching device. This paper reports the detailed operation concept of the device, ex-perimental design, and characterization. The device was tested with MDA-MB-231 breast cancer cells. Experimental results agree well with previously documented morphological changes re-sulting from stretching forces on cancer cells. Remarkably, our new device demonstrates compa-rable cellular changes within a 30-minute compared to the previous 2-hour stretching duration. Moreover, the device design incorporates an open-source software interface, facilitating conven-ient parameter adjustments such as strain, stretching speed, frequency, and duration. Its versatil-ity enables seamless integration with various optical microscopes, thereby yielding novel insights into the realm of mechanobiology.