In order to balance the conflicts among mass flow rate, total pressure ratio, adiabatic efficiency and stall margin in a low-bypass transonic fan, the optimization of the rotor blade is implemented in this study. An advanced 3D optimization design system is adopted, and flow diagnostic methods based on vorticity dynamics are employed to discuss the flow field. Results indicate that by controlling the blade camber line curvature, significant improvements in the aerodynamic performance for the fan stage are achieved, the total pressure ratio is increased by 1.90%, while the adiabatic efficiency and mass flow rate are increased by 4.45% and 5.82%, respectively. Vorticity diagnosis suggest that there exists a close link between performance parameters and vorticity parameters in the axial fan/compressor, both azimuthal vorticity and boundary vortex flux have significant influences on the stage performance. Moreover, the boundary layer separation is accompanied by the spike of entropy and static pressure, while the derivation/gradient of these flow parameters would also suffer drastic changes under the effect of shock wave. The vorticity parameters could provide detailed flow information about the on-wall flow with high accuracy, which provides the researchers with a novel method for the turbomachinery aerodynamic design and analysis.

Livestock farming plays a crucial role in agriculture and is important in meeting people's needs for a better life in the new era. However, due to China's "double carbon" target, the development of animal husbandry has been affected by the level of carbon emissions. To study the spatial dis-tribution and dynamic evolution of livestock carbon emissions in Shandong Province, we used panel data from 16 prefecture-level cities in Shandong Province from 2001 to 2022 to determine the spatial differentiation of livestock carbon emissions in Shandong Province and their dynamic evolution by combining spatial and non-parametric estimation methods based on livestock carbon emissions and livestock emission intensity measured by city. The results of the study show that the distribution of carbon emissions from animal husbandry in Shandong Province is in a "dis-persed-aggregated" pattern, and the intensity of carbon emissions shows a gradual downward trend, with a ladder-like distribution characterized by high in the west and low in the east. Through the analysis of the dynamic evolution of nuclear density, we observe that the regional differences of animal husbandry carbon emissions in Shandong Province are expanding, showing the characteristics of polarization. The difference of carbon emissions in the peninsula is gradually narrowing, and the phenomenon of polarization is weakening. The carbon emissions of animal husbandry in the central and western regions of Shandong are polarized.

Purpose: This study aimed to focus on the design and development of low-cost DIY air purifiers, using a ventilating fan, air pump, water pump, and an ultrasonic generator, with regard to filtration efficacy and also cost-effectiveness that can be used during the COVID-19 pandemic and haze pollution. Methods: Six types of household air purifiers, incorporating a HEPA filter, a HEPA filter & electrostatic fiber, an air pump, an air pump & ultrasonic wave, a water pump, and a water pump & ultrasonic wave, were fabricated. The amount of particulate matter (PM) and CO₂ levels were recorded at 0, 10, 20, 30, and 60 min, then, repeated 3 times. After 10 min of the 3^rd experiment of each study, the last measurement of air pollution would be recorded. Results: At 60 min, the HEPA filter & electrostatic fiber showed the best performance regarding reduction of PM and CO₂ levels. The highest PM reduction rate had occurred at 30 min using an air pump procedure (99.330 to 100%). The CO₂ levels of all experiments had fluctuated at different times. After 10 min of a closed machine, HEPA filter & electrostatic fiber revealed the highest rate of PM elevation, while PM levels of all water-based purifier systems were decreased. A water pump and air pump were the cheapest air cleaners, when taking into account maintenance expenses and electricity charges. Conclusion: An air pump is the optimum method for reducing particulate matter at minimum cost but without the benefit of reduced humidity, while the HEPA filter & electrostatic fiber is the best system to decrease PM levels, but this requires an enclosed structure at the inlet to prevent dust coming back into the room. As filtration efficiency is increased by the use of filters & electrostatic fiber mechanisms, the more expensive the system becomes.

Background: Maternal mortality (MM) is a matter of serious concern in low income developing countries (LDCs). Perspective: A great reduction has been observed regarding the maternal deaths globally after huge efforts since 1990 todate. However, the situation continues to be either stagnant or worsening in developing countries, suggesting that the efforts to cope with this issue are either insufficient or not properly implemented. We need to first diagnose the problem areas that are a great hurdle in the road to success towards the reduction of MM. Postpartum haemorrhage and preeclampsia are one of the most common causes of MM. Malnutrition, neurological dysfunction and cancer are among the non-obstetric causes. Trained medical and paramedical staff can be of great help in this regard by increasing awareness among masses at grass root level. Target set by Millennium Development goal has minimized the MM by 44%. But it has not met the target set by Millenium Development Goals 5 and a lot of measures need to be taken in this regard. Conclusions: Majority of the MDs are preventable and can be avoided by adopting appropriate frameworks, linked data sets, surveillance, birth attendants training, preparation for births, etc. Delay in decision to get healthcare, access to healthcare center and receiving these facilities are the main factors in MM.

Obesity is a troubling public health problem worldwide as it increases risks of respiratory complications, systemic arterial hypertension, type 2 diabetes mellitus, sleep disorders, cardiovascular diseases, and metabolic syndrome (MetS). As a measure to counteract comorbidities associated with severe obesity, bariatric surgery stands out. This study aimed to investigate the adiponectin/leptin ratio in women with severe obesity with and without MetS undergone Roux-en-Y Gastric Bypass (RYGB) and to characterize the biochemical, glucose, and inflammatory parameters of blood in women with severe obesity before and after RYGB. Were enrolled female with severe obesity undergoing RYGP with MetS (n=11) and without (n=39). Anthropometric data and blood samples were obtained before and 6 months after RYGB to analyze total cholesterol, low-density lipoprotein (LDL), high- density lipoprotein (HDL), non-HDL total cholesterol, and glucose; and circulating levels of adiponectin and leptin. Significant reductions in weight, body mass index, and glucose, total cholesterol, LDL, and leptin were observed after surgery, with higher levels of HDL, adiponectin, and adiponectin/leptin ratio observed after surgery compared to preoperative values. This study demonstrated that weight loss induced by RYGB in patients with severe obesity with or without MetS improved biochemical and systemic inflammatory parameters, particularly the adiponectin/leptin ratio.

The stepwise hydrogenation of the C=C bond and C=O group of acrolein on Au₃ and Au₅ model systems is investigated using the density functional theory(DFT) PW91 functional. Our results show that the C=C hydrogenation is more favorable than that of C=O bond on Au₃ with the barriers of the rate-determining step being 0.35 and 0.62 eV respectively. On the other hand, the C=O reduction is preferred over the hydrogenation of the C=C bond on Au₅. The corresponding barriers of the rate-determining steps are 0.45 and 0.54 eV, respectively. This demonstrated that the second hydrogenation step controls the reaction on both Au₃ and Au₅ for C=O and C=C hydrogenation and the C=O hydrogenation on Au₅ is preferred over the hydrogenation of the C=C bond, which is helpful to address the reactivity of small size-selected supported gold clusters.

To facilitate the computation of the uniaxial compressive strength value of the cemented paste backfill under the condition of high sand-cement ratio, and to analyze the size effect of the cemented paste backfill with high sand-cement ratio under varied aspect ratios, the cemented paste backfill specimens with sand-cement ratios of 8:1-24:1 and aspect ratios of 0.5, 1, and 2 were prepared. Through response surface experiments and finite element analysis, the influence of three aspect ratios on the cemented paste backfill strength was explored, and the failure characteristics and size effect mechanisms of cemented paste backfill with various aspect ratios were analyzed. The model of strength conversion between cemented paste backfill with different aspect ratios was established. The results show that the compressive strength of the cemented paste backfill decreases with the increase of the aspect ratio under the same mass concentration and sand-cement ratio. When the aspect ratio is 0.5 and 1, the splitting failure is the main factor; when the aspect ratio is 2, the shearing failure is the main factor. The three-dimensional stress caused by the end effect of the cemented paste backfill is the main reason for the high strength when the aspect ratio is 0.5. Due to the one-dimensional stress zone generated in the middle of the cemented paste backfill with an aspect ratio of 2 in the laboratory, its strength value is closer to the actual uniaxial compressive strength value of the cemented paste backfill. The strength values of the cemented paste backfill with aspect ratios of 0.5 and 1 were higher than the actual uniaxial compressive strength values in the laboratory. The rationality of the theoretical analysis was verified by the ABAQUS analysis results. According to the experimental results, a strength conversion model between different aspect ratios is established, which can provide a reference for the design of the uniaxial compressive strength of the cemented paste backfill.

The effect of the acetylene and hydrogen gases mixture ratios in direct low-temperature vacuum carburization was investigated. The gas ratio is an important parameter for producing the free radicals in the carburization. The free radicals can remove the natural oxide film by the strong reaction of the hydrocarbons, and then thermodynamically activity can be increased. When the gas ratio was below 1, the supersaturation expanded austenite layers were formed on the surface of the AISI 316L stainless steel, which had the maximum carbon solubility up to 11.5 at.% at 743 K, were formed. On the other hand, when the gas ratio was above 1, the carbon concentration of them remained low even if the process time was enough increased to reach the maximum carbon solubility. As a result, the carbon concentration underneath the surface was determined to be highly dependent on the gas mixture ratio of acetylene and hydrogen. In conclusion, it is necessary to restrict the ratio of acetylene and hydrogen gases to total mixture gases to form the expanded austenite layer with the high carbon concentration in the direct low-temperature vacuum carburization.

Obesity is associated with serious comorbidities and economic implications. Bariatric surgery, most commonly Roux-en-Y gastric bypass and sleeve gastrectomy, are effective options for weight loss and improvement of obesity-related comorbidities. With the growing obesity epidemic, there has been a concomitant rise in bariatric surgeries, particularly in sleeve gastrectomy, which has been the most widely performed bariatric surgery since 2013. Gastroesophageal reflux disease (GERD) is highly prevalent in obese individuals, can significantly impact quality of life and may lead to serious complications. Obesity and GERD both improve with weight loss. However, as the incidence of sleeve gastrectomy rises, recent data has revealed a risk of exacerbation of pre-existing GERD or the development of de novo GERD following sleeve gastrectomy. We performed a detailed review of GERD post-sleeve gastrectomy, including its overall incidence, pathophysiology and current treatment paradigms.

Although Darwin‘s evolutionary mutation theory has been widely accepted, many endeavors have been tried to challenge it. With more and more observation of successful hybridization and hybrids, the sexual isolation between species has become vague. The mechanism of evolution has been expanded from the classical model of evolution to multiple routes of speciation. Furthermore, a fundamental crossbreeding theory has been raised and proved by two lines of evidences: paleopolyploidy and fan-shaped spectrum of species. Ancient genome duplications are widespread throughout eukaryotic lineages, particularly in plants. The genome polyploidization, especially in the somatic cell hybridization, can break through the sexual incompatibility between diploid counterparts to hybridize and produce new species. By comparing characteristics, all species in every taxon, both in the extinct fossil and extant organisms, can be arranged into fan-shaped spectrum according to their similarity: left primitive type-middle advanced type-right primitive type. The species are primitive at the two ends and advanced at the middle. The primitive two species always resemble two types of more primitive species that can be confirmed as their ancestors respectively, and the middle species is half similar to the two ancestors respectively. These suggest that the species in the spectrum come from two different ancestors by crossbreeding and gene combination. As a sum, advanced species originated from crossbreeding of two primitive ancestors, by major method of polyploidization, and proved by results of fan-shaped spectrum of species. Then, sex is the cause, force and opportunity for evolution.

In this study, the impact of the addition of high-aspect-ratio nano-ettringite to photocurable epoxy acrylate resin was explored, with a specific focus on the changes observed in viscosity, shrinkage, tensile strength, and elongation at the break of composites formed. Herein, the nano-ettringite samples were modified using KH-570. The 3 wt% or 6 wt% KH-570-modified and unmodified nano-ettringite were dispersed into the resin by ultrasonic treatment in conjunction with mechanical stirring. The grafting effects of nano-ettringite onto KH-570 were analyzed through scanning electron microscopy (SEM), X-ray diffraction (XRD), thermogravimetric (TG) analysis, and Fourier transform infrared spectroscopy (FTIR). The results demonstrate that increased dosages of unmodified and modified nano-ettringite led to increased viscosity of the composite while reducing shrinkage. At the same dosage, the photocurable resin with modified nano-ettringite demonstrated a lower shrinkage and a higher tensile strength. Notably, when the amount of modified nano-ettringite was 3 wt%, the highest tensile strength of the composite was 64.61 MPa, presenting a 72.57% increase compared to the blank sample. Furthermore, the incorporation of modified nano-ettringite as a filler provides a new perspective for improving the performance of photocurable epoxy acrylate resin composites.

Monitoring is an important component of pest management, to prevent or mitigate outbreaks of native pests, and to check for quarantine organisms. Surveys often rely on trapping, especially when the target species respond to semiochemicals. Many traps are available for this purpose, but they are bulky in most cases, which raises transportation and deployment issues, and they are expensive, which limits the size and accuracy of any network. To overpass these difficulties, entomologists have used recycled material, such as modified plastic bottles, producing cheap and reliable traps but at the cost of recurrent handywork, not necessarily possible for all end-users (e.g., for national plant protection organizations). These bottle-traps have allowed very large surveys which would have been impossible with standard commercial traps, and we illustrate this approach with a few examples. Here we present, under a Creative Commons BY-SA License, the blueprint of a fan-trap, a foldable model, laser-cut from a sheet of polypropylene, that can rapidly be produced in large numbers, and could be transported and deployed in the field with very little efforts. Our first field comparisons show that fan-traps are as efficient as bottle-traps, and we describe two cases where they are being used for monitoring.

To improve carbon efficiency for urban logistics service system composed of a third-party logistics service provider (3PLs) and an e-business enterprise, low-carbon operation game between them was studied. Considering low carbon technology investment cost and sales expansion effect of low carbon level, profit functions for both players were constituted. Based on their different bargaining capabilities, totally 5 types of game scenarios were designed. Through analytical solution, Nash Equilibria under varied scenarios were obtained. By analyzing these equilibria, 4 major propositions were given, in which, some key variables and system performance index were compared. Results show that the best system yields could only be achieved under the fully cooperative situation; limited cooperation only for carbon emission reduction would not benefit the system performance improvement; E-business enterprise-leading game’s performance overtook 3PLs-leading ones.

In thermal power plants equipped with air-cooled condensers, axial cooling fans operate under the influence of ambient flow fields. Under inlet cross-flow conditions, the resultant asymmetric flow field is known to introduce additional harmonic forces to the fan blades. This effect has previously been studied only numerically or using blade mounted strain gauges. For this study, Laser Scanning Vibrometry was used to assess fan blade vibration under inlet cross-flow conditions in an adapted fan test rig inside a wind tunnel test section. Two co-rotating laser beams scanned a low pressure axial fan, resulting in spectral, phase resolved surface vibration patterns of the fan blades. Two distinct operating points were examined, with and without inlet cross-flow influence. While almost identical fan vibration patterns were found for both reference operating points, overall blade vibration increased by 100% at low fan flow rate due to cross-flow, and by 20% at high fan flow rate. While numerically predicted natural frequency modes could be confirmed from experimental data as minor peaks in the vibration amplitude spectrum, they were not excited significantly by cross-flow. Instead, primarily higher rotation rate harmonics were amplified, i.a. a synchronous blade tip flapping was strongly excited at the blade pass frequency.

The implementation of sentinel lymph node (SLN) biopsy is changing the scenario in the surgical treatment of early-stage cervical cancer and the oncologic safety of replacing bilateral pelvic lymphadenectomy with SLN biopsy is currently under investigation. One of the undisputed values of SLN biopsy is its diagnostic accuracy in detecting low-volume metastases (LVM) via pathologic ultrastaging. In early-stage cervical cancer, the reported incidence of LVM ranges from 4 to 20%. The prognostic impact and the role of adjuvant treatment in patients with LVM is still unclear. Some non-prespecified analyses in prospective studies showed no impact on the oncologic outcomes compared to node-negative disease. However, the heterogeneity of the studies, the differences in the disease stage and the use of adjuvant treatment, and the concomitant pelvic lymphadenectomy (PLND) make any conclusion on this topic hard. Current guidelines suggest considering micrometastasis (MIC) as a node-positive disease, while isolated tumor cells (ITC) as a node-negative disease, with a low level of evidence. This review aims to highlight the unanswered questions about the definition, identification, prognostic and therapeutic role of LVM and underline the present and future challenges we are facing. We hope this review will guide further research, giving robust evidence on LVM and their impact on clinical practice.

There is a growing interest in the endocannabinoid system and the gut microbiota. Both areas have been suggested to play a role in endometriosis, however this is yet to be studied comprehensively. The purpose of this narrative review is to identify the gaps in endometriosis research in the context of these two areas. It underscores the limited knowledge regarding the involvement of the endocannabinoid system and gut microbiota in endometriosis. Further research in these areas is essential to unlock the therapeutic potential of cannabis and enhance the understanding of endometriosis pathogenesis.

Herein, we present the design technique of a resonant rectifier for piezoelectric (PE) energy harvesting. We propose two diode equivalents to reduce the voltage drop in the rectifier operation, a minuscule-drop-diode equivalent (MDDE) and a low-drop-diode equivalent (LDDE). The diode equivalents are embedded in resonant rectifier integrated circuits (ICs), which use symmetric bias-flip to reduce the power wasted for charging and discharging the internal capacitance of a PE transducer. The self-startup function is supported by synchronously generating control pulses for the bias-flip from the PE transducer. Two resonant rectifier ICs, using both MDDE and LDDE, are fabricated in a 0.18 μm CMOS process and their performances are characterized under external and self-power conditions. Under the external-power condition, the rectifier using LDDE delivers an output power POUT of 564 μW and a rectifier output voltage VRECT of 3.36 V with a power conversion efficiency (PCE) of 90.1%. Under self-power conditions, the rectifier using MDDE delivers a POUT of 288 μW and a VRECT of 2.4 V with a corresponding PCE of 74.6%. The result shows that the power extraction capability of the proposed rectifier is 5.9 and 3.0 times higher than that of a conventional full-bridge rectifier.

Background and Objectives. Prevalence of GERD is increased among individuals with obesity and RYGB is considered as the most effective procedure to control GERD and obesity. However, some patients continue to have GERD after RYGB. The aim of the study was to investigate the prevalence and the risk factors of GERD after RYGB. Material and Methods. This prospective study included 180 patients operated with RYGB and followed for on average of 12.2 (0.6) years. 126 (70%) patients agreed to participate in online consultations and provided data on weight, GERD symptoms, filled GERD-HRQL, TFEQ-18 and GSRS questionnaires. Results. The average age before surgery was 42.7 (10.5) years and BMI was 45.2 (6.4) kg/m2. 128 (71.1%) were females and preoperative GERD was diagnosed in 74 (41.1%) patients. At 12 years follow-up the mean %EBMIL and %TWL were 60.37 and 25.73, respectively. The median %WR was 18.0 (39.0). The GERD was present in 30 (23.8%) patients, of whom 12 (40%) continued to have GERD symptoms and 18 (60%) developed de novo GERD. The GERD-HRQL score significantly decreased from 3.0 (8.0) at baseline to 2.0 (5.0) (p=0.028) at 12 years. GSRS Diarrhea and Indigestion median scores increased significantly, from 1.33 (0.67) to 1.5 (2.42) (p 3.2.

Rapid and accurate detection of road cracks is of great significance for road health monitoring, but currently this work is mainly completed through manual site surveys. Low-altitude UAV remote sensing can obtain images with centimeter or even subcentimeter ground resolution, which provides a new efficient and economical approach for rapid crack detection. Nevertheless, crack detection networks face challenges such as edge blurring and misidentification due to the heterogeneity of road cracks and the complexity of the background. To address these issues, we propose a real-time edge reconstruction crack detection network (ERNet) which adopts multi-level information aggregation to reconstruct crack edges and improve the accuracy of segmentation between the target and background. To capture global dependencies across spatial and channel levels, we propose an efficient bilateral decomposed convolutional attention module (BDAM) that combines depth separable convolution and dilated convolution to capture global dependencies across spatial and channel levels. To enhance the accuracy of crack detection, we use a coordinate-based fusion module that integrates spatial, semantic, and edge reconstruction information. In addition, we propose an automatic measurement of crack information for extracting the crack trunk and its corresponding length and width. Experimental results demonstrate that our network achieves the best balance between accuracy and inference speed.

Introduction: The identification of some prognostic markers in head and neck cancers (HNC) is necessary for the stratification of the therapeutic approach with benefits in increasing treatment response rates and limiting the toxic side effects of treatments. Neutrophil-to-lymphocyte ratio (NLR), lymphocyte-to-monocyte ratio (LMR) and pallets-to-lymphocyte ratio (PLR) are currently validated as cheap and accessible biomarkers in different types of solid tumors. The purpose of the study was to evaluate the possible biomarker value of NLR, PLR and MLR recorded pre-treatment (radiotherapy/chemotherapy) for prognostic purposes in HNC. Materials and methods: The study included 190 patients with HNC included in the oncology record in the oncology outpatient clinic of the Craiova County Emergency Hospital starting from January 2002 and deceased until December 2022. Among them, 40 patients treated multimodally in the Clinic were included in the study of Oncology of the Craiova County Emergency Hospital for which the pre-treatment value (chemotherapy/radiotherapy) of NLR, PLR and MLR could be calculated. Overall survival (OS) values were correlated with NLR, PLR and MLR. Results: Median values for NLR, PLR and MLR were 6.15 (1.24-69), 200.79 (61.3- 1775.0) and 0.53 (0.12-5.5) respectively. In the study, the mean values for NLR, PLR and MLR of 2.88, 142.97 and 0.36 respectively were obtained. Median OS in the study group was 11 months (1-120). Although a negative Pearson`s correlation, the relationship between your variables was only weak, values R =.07, p=.67; R=.02, p=.31 and R=07, p=.62 being related with NLR, PLR and MLR respectively correlation with overall survival (OS). The median values of NLR, PLR and MLR were calculated (1.53, 90.32 and 0.18 respectively) for HNC cases with pre-treatment values of NLR <2 and for HNC cases with NLR values ≥6 (23.5, 232.78 and 0.79 respectively). Median OS for cases with NLR<2 and NLR≥6 were 17.4 and 13 months, respectively. Conclusions: The negative correlations of NLR, PLR and MLR with OS reported in the study are in accordance with the data reported in the literature for locally advanced recurrent and metastatic HNSCC cases. The comparative analysis of the data in the group with NLR<2 and NLR≥6 highlights an advantage of 4.4 months in median OS in favor of the group with low values of NLR. Being cheap and accessible, these markers could change the therapeutic approach even in centers with limited resources. The role of borderline NLR values as a prognostic factor in HNSCC must also be defined. PLR and MLR are less evaluated as biomarkers but the study demonstrates their potential to be used as prognostic biomarkers, it remains to be clarified if their inclusion in multivariable models along with NLR would bring a benefit

This study uses a mass-spring-damping system to simulate the repeated strain of liquefaction cyclic triaxial tests. The two results are compared in this paper to understand the feasibility of the mass-spring-damping system developed in this paper and the feasibility of future research on this related topic and development potential. The main factors affecting this mode's repeated strain are the spring coefficient k and the external force Q0. The spring coefficient has an inverse relationship but does not increase in multiples. The external force has a direct proportional relationship but does not increase the result- a non-multiple increase. When the pore water pressure of the liquefied cyclic triaxial test specimen rises, it will cause the specimen to liquefy, decreasing effective stress, shear modulus G, and damping ratio D, causing an increase in strain. The shear modulus and damping ratio are related to the spring coefficients k and c. Both are variables that change with time. This article takes an original thin-tube specimen at point A in the Yunlin area in Taiwan as a testing example. Through Mathematica software, it can be obtained that the mass m=1kg, the spring coefficient k=244e-0.1t kgf/cm, and the damping coefficient c=0.739e-0.257t kgf-s/cm and external force Q0=10.1sin2πt kg; Finally, this study selected the original thin-tube specimens from four locations in the Yunlin area, and simulated the repeated strain amount of the cyclic triaxial test specimens through a spring-damping system. The results show that the spring-damping system is feasible for simulated cyclic triaxial tests because the model is simple and the parameters are easy to understand and obtain, which also shows the extensibility of this model. Preliminary results of the research show that this model can further simulate the repeated strain obtained by cyclic triaxial tests without considering the increased trend in pore water pressure and the decrease in effective stress during cyclic loading.

The objective of this study is to investigate the effect of the premixed ethanol ratio based on the same total heating value in-cylinder on the equivalence ratio distributions and the injected fuel droplet behavior in the cylinder of the RCCI engine. The spray simulation was conducted by dividing two-part. First, the spray validation simulations progressed to find the spray-influenced factor of the test injector. Next, the engine simulations were performed with the spray-influenced factor obtained from spray validation simulations to investigate the effect of the premixed ethanol ratio based on the same total heating value in-cylinder on the injected fuel atomization and the equivalence ratio distributions. The introduced total heating value was fixed at 595J based on the lower heating value of diesel 14mg. The heating value of the premixed ethanol ratio varied from 0% to 40% based on the same total heating value in-cylinder in steps of 10%. It was revealed that when the premixed ethanol ratio based on the same total heating value in-cylinder was increased, the spray tip penetration value was reduced from the time after 4deg of diesel injection start because of the short injection duration by the small amount of diesel fuel. The SMD value was also more enormous up to 32.58% with increasing the premixed ethanol ratio because of the low kinetic energy of the injected fuel by the short injection duration and the slow evaporation of the injected fuel by the low cylinder temperature.

Many fields of human activity benefit from the ability to create images of obscured objects placed behind walls and to map their displacement in a noninvasive way. Usually, imaging devices like Synthetic Aperture Radars (SAR) and Ground Penetrating Radars (GPR) use expensive dedicated electronics which results in prohibitive prices. This paper presents the experimental implementation and the results obtained from an imaging system capable of performing SAR imaging and interferometric displacement mapping of targets located behind walls, as well as 3D GPR imaging using a low-cost general-purpose radar sensor. The proposed solution uses for the RF section of the system a K-band microwave radar sensor module implementing Frequency Modulated Continuous Wave operation. The low-cost sensor was originally intended for simple presence detection and ranging for domestic applications. The proposed system was tested in several scenarios and proved to operate as intended for a fraction of the cost of a commercial imaging device.

We successfully designed an optimized plenum fan with a three-dimensional, smooth, curved blade. The optimized model revealed that the static pressure in the channel had been increased uniformly and stably, and the flow separation at the leading edge was significantly reduced. To conclude, the three-dimensional blade stabilized the fluid flow, and the flow friction was reduced by suppressing the flow separation as much as possible so that both the static pressure and the static efficiency were clearly improved in comparison with those of the original model. The static efficiency, as a result, was improved by 6% compared with that of the original model.

Emerging pollutants as pharmaceuticals have been focusing international attention for few decades. Ciprofloxacin (CIP) is a common drug widely found in effluents from hospitals, industrial and different wastewater treatment plants, as well as rivers. In this work, the lab-scale 3D-BER system was established, and more than 90% of the antibiotic CIP removal from the Low C/N wastewater. Best results were obtained with current intensity, and different C/N ratio significantly improve the removal of CIP and nitrates, when the ideal conditions were; C/N = 1.5-3.5, pH =7.0-7.5, and I = 60 mA. The highest removal efficiency of CIP = 94.20 %, NO3--N= 95.53 % and total nitrogen (TN) = 84.27 %, respectively. In this novel system, the autotrophic-heterotrophic denitrifying bacteria played vital role for the removal of CIP and enhanced denitrification process. Thus, autotrophic denitrifying bacteria uses CO2 and H2 as carbon sources to reduce nitrates to N2. This system has the assortment and prosperous community revealed at the current intensity of 60 mA, and the analysis of bacterial community structure in effluent samples fluctuates under different condition of C/N ratios. According to the results of LC-MS/MS analysis, the intermediate products were proposed after efficient biodegradation of CIP. Microbial community on biodegrading was mostly found at phylum, and class level was dominantly responsible for the NO3--N and biodegradation of CIP. This work can provide some new insights towards the biodegradation of CIP and the efficient removal of nitrates from low C/N wastewater treatment by the novel 3D-BER system.

A proposed low-temperature forging method aims to enhance stainless steel bearings by creating a martensitic subsurface layer, significantly boosting bearing fatigue life due to increased surface hardness. This technique induces beneficial residual stresses, particularly in axial bearings, streamlining their construction and improving machine elements. Challenges persist, especially with radial bearings, but simplicity in axial bearing forging promotes compact, resource-efficient facility construction. Future research will focus on applying this technique to axial bearing washers, potentially replicating success in other bearing components. Despite the energy ex-penditure for cooling during forging, the substantial increase in bearing fatigue life offsets this, enhancing overall longevity and reliability of critical machine components. Integration of this forging technique into bearing fabrication appears seamless, offering a promising trade-off be-tween energy use and enhanced performance.

The aims of the study are: a) Describe the reactogenicity of WHO-approved two mRNA (Pfizer-BioNTech, Moderna) and two non-RNA vaccines (Oxford-AstraZeneca, Sinovac) among lactating mother and baby pairs; and b) compare and contrast the reactogenicity between mRNA and non-mRNA vaccines. A cross-sectional, self-reported survey was conducted amongst 1784 lactating women who received COVID-19 vaccinations. The most common maternal adverse reaction was a local reaction at the injection site; the largest minority of respondents, 43.7% (780/1784), reported experiencing worse symptoms when receiving the second dose compared to the first dose. There were no major reported adverse effects or behavioural changes in the breastfed infants. Among the respondents who received non-mRNA COVID-19 vaccinations, a majority reported no change in lactation but those who did more commonly reported an increase in milk supply, decrease in milk supply and pain in the breast. The more commonly reported lactation changes (fluctuations in breastmilk supply and pain in the breast) for the non-mRNA vaccines were similar to that of respondents who received mRNA vaccines. Our study, with a large cohort and wide geographical and racial mix, further augments earlier reported findings that COVID-19 vaccines are safe for breastfeeding mothers and her children.

The study comprehensively evaluated the prognostic roles of PLR, NLR, MLR, BLR, and ELR in patients with acute exacerbation chronic obstructive pulmonary disease (AECOPD). 619 patients with AECOPD and 300 healthy volunteers were retrospectively included into the study. The clinical characteristics containing laboratory findings of the AECOPD patients and the blood cell counts (CBCs) of the healthy volunteers were collected. Compared with the healthy volunteers, PLR, NLR, and MLR were elevated in COPD patients in stable condition, and were further ele-vated during exacerbation. ELR showed the opposite trend. PLR, NLR, and MLR were all posi-tively correlated with hospital LOS as well as CRP. In contrast, ELR was negatively correlated with hospital LOS as well as CRP. Elevated PLR, NLR, and MLR were all associated with more serious airflow limitation in AECOPD. Elevated PLR, NLR, and MLR were all associated with increased in-hospital mortality while Elevated ELR was associated with decreased in-hospital mortality in AECOPD. A nomogram was construct to predict in-hospital mortality in AECOPD. The nomo-gram had a C-index of 0.850 (95% CI: 0.799 – 0.901) with good predictive value and clinical ap-plicability. In summary, PLR, NLR, MLR, and ELR served as predictors for clinical outcomes in patients with AECOPD.

In this paper, spacetime is defined as the absolutely invariant homogeneous "coordinate spacetime" frame and its modulation by the relatively variable non-homogeneous "metric spacetime" under its constraints. This modulation is caused by matter and motion, and carries the function of transmitting interactions, reflecting the diffeomorphism invariance and Lorentz invariance. This inhomogeneous spacetime concept makes the medium nature of spacetime more obvious and avoids the problem of "path dependence" caused by the concept of curved spacetime. In this paper, it is argued that all energy-momentum has internal spatio-temporal properties, and all interactions must be transmitted through spacetime metrics. On this basis, a converging and dispersing cyclic multiverse model is proposed. This model of the universe is inevitable as long as there are two macroscopic manifestations of the matter of the universe, namely, gravitation induced convergence and "explosive" dispersion caused by different factors. The new cosmic model matches the observed accelerated "expansion" of the universe and no longer requires the dark energy hypothesis.

This paper empirically analyzes the relationship between digital inclusive finance and rural income, and demonstrates that digital inclusive finance plays a significant role in promoting rural income, based on the 2012-2018 panel data of 17 cities in Henan Province of China. Further dimensional research unveils that all of its breadth of coverage, depth of use and degree of digitization present significant positive correlation with rural income, and a robustness test was conducted through the sub-sample method. In addition, according to regression analysis on the influencing factors of digital inclusive finance through the Tobit model, the level of economic development, the Internet popularity rate and the urbanization rate have a positive effect on the development of digital inclusive finance in Henan, while the income gap between urban and rural areas and the degree of opening up have a negative effect. Finally, predicated on the analysis of the restrictive factors of Henan’s digital inclusive finance in increasing rural income, the paper puts forward specific policy proposals based on the native state quo.

A low-cost bio-mass-derived carbon substrate has been employed to synthesize MoS₂@carbon composites through a hydrothermal method. Carbon fibers derived from natural cotton provide a three-dimensional and open framework for the uniform growth of MoS₂ nanosheets, thus constructing hierarchically coaxial architecture. The unique structure could synergistically benefit fast Li-ion and electron transport from the conductive carbon scaffold and porous MoS₂ nanostructures. As a result, the MoS₂@carbon composites, when served as anodes for Li-ion batteries, exhibit a high reversible specific capacity of 820 mAh g^-1, high-rate capability (457 mAh g^-1 at 2 A g^-1), and excellent cycling stability. The superior electrochemical performance makes the MoS₂@carbon composites to be low-cost and promising anode materials for Li-ion batteries.

Underwater Sensor Networks (UWSNs) can enable a broad range of applications such as resource monitoring, disaster prevention, and navigation-assisted. It is especially relevant for sensor nodes location in UWSNs. Global Positioning System (GPS) is not suitable for using in UWSNs because of the underwater propagation problems. Hence some localization algorithms based on the precise time synchronization between sensor nodes have been proposed which are not feasible for UWSNs. In this paper, we propose a localization algorithm called Two-Phase Time Synchronization-Free Localization Algorithm (TP-TSFLA). TP-TSFLA contains two phases, namely, range-based estimation phase and range-free evaluation phase. In the first phase, we address a time synchronization-free localization scheme base on the Particle Swarm Optimization (PSO) algorithm to decrease the localization error. In the second phase, we propose a Circle-based Range-Free Localization Algorithm (CRFLA) to locate the unlocalized sensor nodes which cannot obtain the location information through the first phase. In the second phase, sensor nodes which are localized in the first phase act as the new anchor nodes to help realize localization. Hence in this algorithm, we use a small number of mobile beacons to help achieve location without any other anchor nodes. Besides, to improve the precision of the range-free method, an extension of CRFLA by designing a coordinate adjustment scheme is updated. The simulation results show that TP-TSFLA can achieve a relative high localization ratio without time synchronization.

The existence of palindrome numbers of arbitrary length greater than 2 that are divisible by the prime number 37 is proven in this paper. The method to construct such a palindrome is also described. It turns out that a palindrome number divisible by 37 is also divisible by 3 and, consequently, divisible by 111.

The concept of {\it quantum ratio} emerged in the recent efforts to understand how Newton's equations appear for the center of mass (CM) of an isolated macroscopic body at finite body-temperatures, as the first approximation to quantum-mechanical equations. It is defined as $Q\equiv R_q/L_0$, where the quantum fluctuation range $R_q$ is the spatial extension of the pure-state CM wave function, whereas $L_0$ stands for the body's linear size (the space support of the internal, bound-state wave function). The two cases $R_q /L_0 \lesssim 1$ or $R_q/ L_0 \gg 1$, roughly correspond to the body's CM behaving classically or quantum mechanically, respectively. In the present note we elaborate more on this concept, illustrating it in several examples. An important notion following from introduction of the quantum ratio is that the elementary particles (thus the electron and the photon) are quantum mechanical, even when the environment-induced decoherence turns them into a mixed state. Decoherence and classical state should not be identified. This simple observation, further illustrationed by the consideration of a few atomic or molecular processes, may have significant implications on the way quantum mechanics works in biological systems.

In this paper, some mixed type bounds on the spectral radius $\rho(A\circ B)$ for the Hadamard product of two nonnegative matrices ($A$ and $B$) and the minimum eigenvalue $\tau(C\star D)$ of the Fan product of two $M$-matrices ($C$ and $D$) are researched. These bounds complement some corresponding results on the simple type bounds. In addition, a new lower bound on the minimum eigenvalue of the Fan product of several $M$-matrices is also presented: $$ \tau(A_{1}\star A_{2}\cdots\star A_{m})\geq \min_{1\leq i\leq n}\{\prod^{m}_{k=1}A_{k}(i,i)-\prod^{m}_{k=1}[A_{k}(i,i)^{P_{k}}-\tau(A_{k}^{(P_{k})})]^\frac{1}{P_{k}}\}, $$ where $A_{1},\ldots, A_{k}$ are $n\times n$ $M$-matrices and $P_{1},\ldots, P_{k}>0$ satisfy $\sum^{m}_{k=1}\frac{1}{P_{k}}\geq 1$. Some special cases of the above result and numerical examples show that this new bound improves some existing results.

The concept of smart morphing blades, which can control themselves to reduce or eliminate the need for active control systems, is a highly attractive solution in blade technology. In this paper an innovative passive control system based on Shape Memory Alloys (SMAs) is proposed. On the basis of previous thermal and shape characterization of a single morphing blade for a heavy-duty automotive cooling axial fan, this study deals with the numerical analysis of the aerodynamic loads acting on the fan. By coupling CFD and FEM approaches it is possible to analyze the actual blade shape resulting from both the aerodynamic and centrifugal loads. The numerical results indicate that the polymeric blade structure ensures proper resistance and enables shape variation due to the action of the SMA strips.

Deterministic-stochastic empirical mode decomposition (EMD) is used to obtain low-frequency (non-diffusive, i.e., background velocity) and high-frequency (diffusive, i.e., eddies) components from a Lagrangian drifter‘s trajectory. Eddy characteristics are determined from the time series of eddy trajectories from individual Lagrangian drifter such as the eddy radial scale, eddy velocity scale, eddy Rossby number, and eddy-background kinetic energy ratio. A long-term dataset of the SOund Fixing And Ranging float time series obtained near the California coast by the Naval Postgraduate School from 1992 to 2004 at depth between 150 and 600 m (http://www.oc.nps.edu/npsRAFOS/) is used as an example to demonstrate the capability of the deterministic-stochastic EMD.

Macrophages undergo different cellular states upon activation that can be hyporesponsive (tolerated) or hyperresponsive (primed or trained) to subsequent stimuli. Epigenetic modifications are known to play a key role in determining these cellular states. However, little is known about the role of signaling pathways that lead to these epigenetic modifications. Here, we examined the effects of various inhibitors targeting key signaling pathways induced by lipopolysaccharide (LPS) on tolerance and priming in the murine macrophages. We found that a prolonged inhibition (>18 h) of the MEK1/2-ERK signaling axis reversed tolerance and primed cells in expressing IL-1β and other inflammatory cytokines such as IL-6, TNFα, and CXCL10. Ectopic expression of catalytically active and inactive MEK1 mutants suppressed and enhanced IL-1β expression, respectively. Primed cells by the MEK1/2 inhibitor U0126 expressed higher levels of gene sets associated with immune responses and cytokine/chemokine production but lower levels of genes with cell cycle progression, chromosome organization, and heterochromatin formation than non-primed cells. Of interest, expression of the histone 3 lysine 9 (H3K9) methyltransferase Suv39h1 and the H3K9 methylation reader Cbx5 was substantially suppressed, whereas the H3K9 demethylase Kdm7a was enhanced, suggesting a role of the MEK1/2-ERK signaling axis in H3K9 demethylation. The H3K9 trimethylation levels in the genomic regions of IL-1β, TNFα, and CXCL10 were decreased by U0126. Also, the H3K9 methyltransferase inhibitor BIX01294 mimicked and overexpression of Cbx5 prevented the U0126 training effects in both RAW264.7 cells and bone marrow-derived macrophages. Collectively, these data suggest that prolonged inhibition of the MEK1/2-ERK signaling axis reverses tolerance and primed macrophages likely through decreasing H3K9 methylation levels.

Achieving the thermal conductivity required for efficient heat management in semiconductors and other devices requires the integration of thermally conductive ceramic fillers at concentrations of 60 vol% or higher. However, the increased filler content often negatively affects the mechanical properties of the composite matrix, limiting its practical applicability. To address this issue, in this paper, we present a new strategy to reduce the required ceramic filler content: the use of a thermally conductive ceramic composite filler with carbon nanotubes (CNT) grown on aluminum nitride (AlN). We have combined catalyst coating technology with vacuum filtration to ensure that the catalyst is uniformly applied to micrometer-sized AlN particles, followed by efficient and uniform synthesis of CNTs using a water-assisted process in a vertical furnace. By carefully controlling the number of vacuum filtration cycles and the growth time of the CNTs, we demonstrate precise control over the number and length of the CNT layers, thereby adjusting the properties of the composite to the intended specifications. When AlN/CNT hybrid fillers are incorporated into silicone rubber, while maintaining the mechanical properties of rubber, the thermal diffusivity achieved at reduced filler levels exceeds that of composites using AlN-only or simultaneous AlN and CNTs formulations. This demonstrates the critical role of CNTs on AlN surfaces. Our study represents a significant advancement in the design of thermally conductive materials with potential implications for a wide range of applications.

Background: this interventional pilot study aimed to evaluate the short-term (3 years) efficacy of focal laser ablation (FLA) in treating the index lesion of low-intermediate risk prostate cancer, along with assessing the safety of the procedure (ClinicalTrials.gov ID NCT04045756). Methods: forty patients aged between 46 and 86 with histologically proven organ-confined prostate cancer and low to intermediate progression risk were included. FLA was performed under percutaneous fusion magnetic resonance/ultrasound guidance in a Day Hospital setting under local anesthesia. Patients underwent regular clinical assessments, PSA measurements, post-procedure MRI scans, and biopsies at 36 months or if positive findings were detected earlier. Statistical analyses were conducted to assess trends in PSA levels and cavity dimensions over time. Results: forty patients were initially included, with 15 lost to follow-up. At 36 months, a mean PSA reduction of 60% was observed, and 80% of MRI scans showed no signs of in-field clinically significant residual/recurrent cancer. Biopsies at 36 months revealed no malignant findings in 20 patients. No deterioration in sexual function or urinary symptoms was recorded. Conclusions: FLA appears to be safe, feasible and effective in the index lesion treatment of low-intermediate risk prostate cancer, with a high rate of tumor eradication and preservation of quality of life.

Because Newton's gravity and Einstein's general theory of relativity are macroscopic gravitational theories, therefore, this paper attempts to establish a set of quantum gravity theory of the microscopic expression of Newton's and Einstein's theory of gravity to make up for the shortcomings of the existing macro-gravity theory at the micro level, and further develop the macroscopic gravity theory into the microscopic field. Based on the cognition of the field theory model, from the general assumption, space-time is further regarded as an ideal fluid, from the perspective of the distribution of ideal fluid density, this paper derives the Newton's universal gravitational equation and Einstein's general relativity equation. On the micro level, the gravitational field is further interpreted as a gradient field of space-time density; the Newtonian potential is further interpreted as the density of an object at the micro level; gravity is further interpreted as the potential pressure(space-time pressure) exhibited by the gradient of the density of the object at the micro level; flection space-time is further interpreted as the embodiment of the gradient distribution of the ideal fluid (space-time) density at the micro level. Based on a modified gravitational model, it explains the dynamics of the stars' rotation and revolution.

Tourism is an important industry that promotes national economic and social progress. All-for-one tourism is a new concept of regionally coordinated development that uses the tourism industry as an engine to boost resource integration, industrial integration, and social sharing. Tourism service is the main embodiment of cultural ecosystem services for all-for-one tourism cities. Taking Liyang in China as an example, this paper used a combination of GIS spatial analysis and big data text mining to evaluate the tourism service from three aspects: the quality of tourism resources, the comprehensiveness of tourism service facilities, and the satisfaction of tourists. The results show that (1) the tourism service is better in the northwestern and eastern areas of the city, while it is lower in the northeastern and southwestern parts; (2) the hotspot areas should focus on improving the tour routes, the transport capacity, and excessive charges; the cold spot areas should work on ecological restoration and creating new tourism attractions by combining the local industries; (3) rural tourism integrating agriculture and visitation should be highlighted as a key growth point to improve the city’s tourism service function.

Air pollution has created a lot of problems in the developed and developing countries. To avoid or reduce these problems, constant monitoring of the air should be ensured. The conventional techniques is costly because it requires a lot of money and time consuming. Biomonitoring has been the alternative method. Moss, lichens and plants are biomonitors available to entrap air pollutants. The aim of this paper is to discuss one of the ways of monitoring air pollution – Moss bag technique. To do this, types, choice, preparation, handling of bags after preparation of moss were discussed. From the literatures consulted, it was discovered that there were differences in the techniques used by the researchers. In all, the use of mosses with emphasis on the employment of moss bag have proved to be a powerful tool in airborne particulate and toxic elements. To conclude, developing countries should focus more on this technique because it will reduce cost of air monitoring.

Moso bamboo is famous for fast growing and biomass accumulation, as well as high annual output for timber and bamboo shoots. These high outputs require high nutrient inputs to maintain and improve stand productivity. Soil nitrogen (N), phosphorus (P) and potassium (K) are important micronutrients for plant growth and productivity. Due to high variability of soils, analysing spatial patterns of soil N, P and K stocks is necessary for scientific nutrient management in Moso bamboo forests. In this study, soils were sampled from 138 locations across Yong’an City and ordinary kriging was applied for spatial interpolation of soil N, P and K stocks. Soil N stock showed a strong spatial dependence while soil N and P stocks presented a moderate spatial dependence, indicating soil N was mainly controlled by intrinsic factors while soil N and P stocks were controlled by both intrinsic and extrinsic factors. Different spatial patterns were observed for soil N, P and K stocks across the whole study area, indicating that fertilizations with different ratios of N:P:K should be applied for different sites to maintain and improve stand productivity. The total soil N, P and K stocks within 0-60 cm were 0.624, 0.020 and 0.583 Tg, respectively.

A large core size and bending resistance are very important properties of mid-infrared energy transfer fibers, but large core sizes usually lead to a deterioration of bending properties. A negative-curvature nested node-free anti-resonant hollow-core fiber (AR-HCF) based on quartz is proposed. It was made by adding a nested layer to a previous AR-HCF design to provide an additional anti-resonance region while keeping the gap between adjacent tubes strictly correlated to the core diameter to produce a node-free structure. These features improve the fiber’s bending resistance while achieving a larger core diameter. The simulation results show that the radial air-glass anti-resonant layer is increased by the introduction of the nested anti-resonant tube, and the weak interference overlap between the fiber core and the cladding mode is reduced, so the fiber core’s limiting loss and the sensitivity to bending are effectively reduced. When the capillary wall thickness t of the fiber is 0.71 μm, the core diameter D is 70 μm, the ratio of the inner diameter of the cladding capillary to the core diameter d/D is 0.62, and the diameter of the nested tube is d0=29 μm, the fiber has a lower limiting loss at the wavelength of 2.79 μm, and the limiting loss is 3.28×10-4 dB/m. At the same time, the optimized structure also has good bending resistance. When the bending radius is 30 mm, the bending loss is only 4.72×10-2 dB/m. To our knowledge, this is the first research to achieve an anti-bending low-loss micro-structure hollow fiber with a bending radius of less than 30 mm in the 2.79 μm band. An anti-bending low-loss anti-resonant hollow-core fiber with this structure constitutes a reliable choice for the light guiding system of a 2.79 μm band erbium laser therapy instrument.

Background/Goals: The gut hormone PYY secreted from intestinal L-cells has been implicated in the mechanisms of satiation via Y2-receptor (Y2R) signaling in the brain and periphery and is a major candidate for mediating the beneficial effects of bariatric surgery on appetite and body weight. Methods: Here we assessed the role of Y2R signaling in the response to low- and high-fat diets and its role in the effects of Roux-en-Y gastric bypass (RYGB) surgery on body weight, body composition, food intake, energy expenditure and glucose handling, in global Y2R-deficient (Y2RKO) and wildtype mice made obese on high-fat diet. Results: Both male and female Y2RKO mice responded normally to low- and high-fat diet in terms of body weight, body composition, fasting levels of glucose and insulin, as well as glucose and insulin tolerance for up to 30 weeks of age. Contrary to expectations, obese Y2RKO mice also responded similarly to RYGB compared to WT mice for up to 20 weeks after surgery, with initial hypophagia, sustained body weight loss, and significant improvements in fasting insulin, glucose tolerance, HOMA-IR, and liver weight compared to sham-operated mice. Furthermore, non-surgical Y2RKO mice weight-matched to RYGB showed the same improvements in glycemic control as Y2RKO mice with RYGB that were similar to WT mice. Conclusions: PYY signaling through Y2R is not required for the normal appetite-suppressing and body weight-lowering effects of RYGB in this global knockout mouse model. Potential compensatory adaptations of PYY signaling through other receptor subtypes or other gut satiety hormones such as GLP-1 remain to be investigated.

Purpose: To create a highly balanced comparison of ab interno trabeculectomy (Trabectome, AIT) and trabecular bypass stenting (iStent, TBS).Setting: Eye and Ear Institute, Pittsburgh, Ross Eye Institute, Buffalo, and Glaucoma Associates of Texas, Dallas, USA.Design: Retrospective Exact Matching analysis.Methods: AIT and TBS patients were included from three large glaucoma practices. The primary outcome measure was the unmedicated IOP ≤ 21 mmHg at 2-year follow-up visit. A secondary measure was unmedicated IOP reduction ≥ 20% at 2 years. Patients were matched by baseline IOP, the number of glaucoma medications and glaucoma type using Exact Matching and by age using Nearest Neighbor matching. Patients without a close match were excluded. All surgeries were combined with phacoemulsification. Results: 154 AIT and 110 TBS eyes were analyzed. 48 AIT patients were exactly matched to 48 TBS patients. Both groups had a baseline IOP of 15.3±3.1 mmHg. At 24 months, the mean IOP was 13.9±3.3 for AIT versus 16.8±2.8 mmHg for TBS (p=0.04), while the number of medications was 0.7±1.0 for AIT versus 1.7±1.2 for TBS (p=0.04). The proportion of subjects achieving IOP ≤ 21 mmHg without medications at 24 months was 53% in AIT versus 16.6% in TBS (P < 0.05). At 24-month follow up 17.6% of patients in AIT had ≥ 20% IOP reduction without medication versus no patient in TBS. Conclusions: An Exact Matching comparison of AIT and TBS demonstrated greater IOP reduction with fewer medications in AIT.

Classical mechanics describes the laws of motion in the macroscopic material world, while quantum mechanics describes the laws of motion in the microscopic material world that classical mechanics cannot explain, and achieves a highly accurate mathematical representation of the laws of microscopic physical motion. But even with such a successful theory, there is confusion about the probability wave. Therefore, this paper attempts to improve the physical definition of the conceptual basis of quantum mechanics, thus solving the confusion of quantum mechanical probability waves, and finally surprisingly discovered another feasible interpretation of the principle of cosmic redshift and the invariance of the speed of light.

INTRODUCTION: Achalasia is a pathology with an incidence of 1 in 100,000 inhabitants per year. There are very limited data on achalasia in the obese population, especially in those undergoing bariatric surgery. The approach of choice for cases of achalasia is fundoplication to correct the reflux; however, lacking a fundus due to a previous gastrectomy, an alternative that offers optimal results should be chosen. Here we present the surgical approach in a case of esophageal achalasia and a history of vertical sleeve gastrectomy, where we performed simultaneous Heller's cardiomyotomy and laparoscopic Roux-en-Y gastric bypass, as well as the results obtained. CASE PRESENTATION: 44-year-old woman with no chronic degenerative diseases, with a previous record of vertical sleeve gastrectomy 5 years ago, who started 1 year and 5 months earlier with dysphagia to liquids, then to solids, in addition to weight loss of 10 kilograms in 4 months. The BMI before vertical sleeve gastrectomy was 32 kg/m2, her BMI at the time of admission was 20 kg/m2; she also presented regurgitation and generalized weakness. After analyzing the surgical options, it was decided to perform a Heller cardiomyotomy and a Roux-en-Y gastric bypass. DISCUSSION AND CONCLUSIONS: The procedure turned out to be safe and successful in treating achalasia symptomatology, in addition to complete resolution of the reflux symptom.

Acoustic Radiation Forced Impulse (ARFI) is an ultrasound integrated method, measuring stiff-ness by point shear wave elastography. To evaluate the diagnostic performance of ARFI of the liver and of the spleen, combined with spleen dimension and platelet count, in predicting clinical events in cirrhosis, a prospective and cross-sectional study was conducted between February 2017 and February 2021. The following ratio scores with ARFI measurements were performed: ALSDP (ARFI Liver-Spleen Diameter-to-Platelets ratio score), ASSDP (ARFI Spleen-Spleen Diam-eter-to-Platelets ratio score), ASSAP (ARFI Spleen-Spleen Area-to-Platelets ratio score), ALSAP (ARFI Liver-Spleen Area-to-Platelets ratio score). In 100 enrolled subjects, spleen ARFI, ASSDP, ASSAP, were significantly associated with high-risk oesophageal varices (HRVs) in the prospec-tive short- and long-term follow-up and in the cross-sectional study (p 0.7). ARFI-ratio scores can predict, in cirrhotic patients, the risk of developing HVRs in short and long-term period.

Toshiba devised the bladeless fan (or Air Multiplier) concept in 1981. Researchers like James Dyson and Jafari et al. further developed it. Bladeless fans are more energy-efficient, safer due to the hidden blades, easier to clean, and more adjustable than conventional fans. From a performance point of view, bladeless fans are better because they multiply mass flow rate, eliminate buffeting, consume less power, and are quieter. This paper investigates the influence of the airfoil’s outlet slit thickness on the discharge ratio by varying the outlet slit thickness of an Eppler 473 airfoil from 1.2 mm to 2 mm in intervals of 0.2 mm. Results indicated that smaller slits showed higher discharge ratios. The airfoil with a 1.2 mm slit thickness showed a discharge ratio of 18.78, a 24% increase from the discharge ratio of the 2 mm slit. The effect of outlet angle on the pressure drop across the airfoil was also studied. Outlet angles were varied from 16∘ to 26∘ by an interval of 2∘. The airfoil profile with a 24∘ outlet angle showed a maximum pressure difference of 965 Pa between the slit and leading edge. In contrast, the 16∘ outlet angle showed the least pressure difference of 355 Pa. Parameters such as average velocity, turbulent kinetic energy, the standard deviation of velocity and outlet velocity magnitude was used to assess the performance of airfoil profiles used in bladeless fan.

Concerning fan systems with an air pipe connecting air intake and a closed outlet, aerodynamic noise cannot be directly transmitted from the fan inlet and outlet to the outside. At this moment, the volute vibrational radiation noise induced casing surface vibration is the major noise component. The main factors affecting the fan vibrational noise are analyzed through theoretical derivation, then a vibrational noise optimization control method for the volute casing is proposed that considered the influence of vibro-acoustic coupling, taking the panel thickness of the volute (front-panel thickness [FT], side-panel thickness [ST], and back-panel thickness [BT]) as design variables, and the acoustical power of the volute surface and the total mass of the volute as the optimal target function. The optimization method is mainly divided into three main parts: the first was based on the simulation of unsteady flow of the fan to obtain the vibrational noise source; the second, using the design of experimental (DOE) method and the proposed numerical simulation of fluid-structure-acoustic coupling method to obtain the designing space, then the radical-based function (RBF) method is used to construct the approximate surrogate model instead of the simulation model previously mentioned, which was used to provide the basic mathematical model for the optimization of the next part; the third part, implementing the low vibrational noise optimization for the fan volute, applied the single-target (taking volute radiated acoustical power as the target function) and the multi-target (taking the volute radiated acoustical power and volute total mass as the target function) methods. In addition, the fan aerodynamic performance, volute casing surface fluctuations, and vibration response were validated by experiments, showing good agreement. It is of utmost importance that the dynamic pressure measurements and vibrational tests on the volute casing verify the accuracy of the numerical calculation. The optimization results showed that the vibrational noise optimization method proposed in this study can effectively reduce the vibration noise of the fan, obtaining a maximum value of noise reduction of 7.3 dB. The optimization identified in this paper provides a significant reference for the design of a low-vibrational-noise volute.

The Gurney flap (GF) is a miniature lift-enhancement device and is usually mounted at the trailing edge of an airfoil. The GF and has been successfully applied to isolated airfoils, multi-element airfoils, and aircraft wings as well as helicopter rotor due to its attractive features of simplicity, cost-effective and separation control. The GF also has aroused the attention of researchers in the turbomachinery industry. However, limited studies are currently available on the application of a GF to an axial fan.Hence, in this paper, we conduct a wind tunnel and computational fluid dynamic (CFD) investigation on an axial fan profiled with a NACA 65-(12)10 airfoil to evaluate the effect of the GF on the performance of the fan. We also present the detailed flow features of the fan with and without the GF after validating the simulation results with the experimental results. The experimental results show that as the GF is installed higher on the fan blade, it can produce a higher total pressure rise accompanied with a greater loss of efficiency. The installation of the GF also enlarges the work capacity of the fan. Detailed flow field analysis, including the surface pressure distribution, vorticity distribution at the trailing edge and streamline distribution of the fan, is carried out to understand the mechanisms of the effect of the GF on the performance of the fan.

Background: Psoriasis is a chronic immune-mediated skin disease in which systemic inflammation plays an important role in the pathogenesis. In recent years, neutrophil-to-lymphocyte ratio (NLR), neutrophil-to-monocyte ratio (NMR), platelet-to-lymphocyte ratio (PLR), and systemic immune-inflammation index (SII) have been shown to be important indicators of inflammation. In this study, our aim is to investigate NLR, NMR, PLR, and SII levels in psoriasis patients treated with biologic agents. Method: Clinical and biochemical data of 209 patients who received systemic therapy for psoriasis were obtained by retrospectively reviewing their medical records. NLR, NMR, PLR, and SII values were calculated from the hemogram values of the patients. Results: In the third month of follow-up, the mean CRP, NLR, NMR, PLR, and SII values were significantly decreased compared to the baseline values. SII values showed strong positive correlations with NLR, NMR and PLR. Adalimumab, etanercept, and infliximab, which are TNF-α blockers, were observed to be more effective on PLR and NLR and especially NMR. Conclusion: NLR, NMR, PLR, and SII, which are data obtained from routine blood tests, can be used in the monitoring of treatment of psoriasis, especially with TNF- α blockers.

With covid infection having a periodic occurrence and each wave affecting millions of people, there is an urgent need for healthcare providers to develop readily available biological markers to predict the severity and mortality of COVID-19 infection at an early stage of the disease to predict the most optimal management. The Neutrophil – lymphocyte Ratio (NLR) and Platelet-lymphocyte ratio (PLR), are novel inflammatory markers suggested to predict the severity of illness in COVID -19 patients. We evaluated a retrospective cohort of 224 patients with covid 19 illnesses from August 2020 to October 2020. We categorized the patients into 'mild' and 'moderate to severe as per the severity of their illnesses. The optimal cut-off values of the continuous NLR, PLR, and Age were calculated by applying the receiver operating characteristic (ROC) curve analysis. Sensitivity, specificity, and likelihood ratios were calculated from ROC analysis. The results showed that Age, Hb, and NLR are significant predictors of the severity of illness. So we quantified the predictive contribution of those variables by its Z- score and showed that NLR is the strongest predictor followed by Age.ROC curve analysis revealed NLR to be an excellent predictor of disease severity (sensitivity 88.30% and specificity 82.60%) at a cut-off of > 4.24. A cut-off of 165.63 was obtained for PLR, which showed good predictive value for the severity of illness. A NLR > 6 was used as a predictor for mortality due to covid illness with good sensitivity and specificity. Conclusion: NLR and PLR can be used as prognostic markers to identify the severity of covid illness and the probability of mortality in the future in low-resource settings. Given its low cost, easily available, accessible, and reproducible data, it can be used as a useful marker to assist the physician in early referral and treatment of covid 19 infected patients.

The golden ratio, also known as Phi (ϕ ≈ 1.618034), attracted the interest of mathematicians, artists, and intellectuals for many centuries, probably from when it was discovered in human anthropometry. Even in recent times, researchers found the presence of golden ratio in Renaissance paintings and aesthetic preferences. The reasons behind the fascination with the golden ratio remain unclear, but it has been suggested that stimuli containing this proportion are often perceived as beautiful. However, evidence is conflicting, and the literature struggles to establish the existence of individual preferences for golden ratio. To gain new insights into the nature of these preferences, one hundred participants completed an implicit association task, with either golden ratio or random stimuli presented with positive or negative words. Participants initially categorized the stimuli based on their assigned categories. Then, we assessed their explicit preferences by asking to rate the stimuli in terms of pleasantness and by completing a line bisection task and the Ultimate Game. The results revealed the typical effects observed in implicit association tasks, with improved response times and accuracy when golden ratio stimuli were associated with positive word categories. In contrast, explicit ratings yielded mixed results. We discuss our findings in relation to previous studies that have explored this issue, highlighting the ongoing debate surrounding preferences for the golden ratio.

Despite the fact that COVID-19 treatment and management are now considerably regulated, SARS-CoV-2 is still one of the leading causes of death in 2022. The availability of COVID-19 vaccines, FDA-approved antivirals, and monoclonal antibodies in low-income countries still poses an issue to be addressed. Natural products, particularly traditional Chinese medicines (TCMs) and medicinal plant extracts (or their active component) have challenged the dominance of drug repurposing and synthetic compound libraries in COVID-19 therapeutics. Abundant resources and excellent antiviral performance make natural products a relatively cheap and easily available alternative for COVID-19 therapeutics. Here, we deliberately review the anti-SARS-CoV-2 mechanisms of the natural products, their potency (pharmacological profiles), and application strategies for COVID-19 intervention. In light of their advantages, this review is intended to acknowledge the potential of natural products as COVID-19 therapeutic candidates.

Background: The hypothesis is that a hypoxic-hyperoxic preconditioning (HHP) is associated with a protective effect on myocardial function by reducing endothelial damage and a beneficial effect on postoperative outcome in patients undergoing cardiac surgery with cardiopulmonary bypass (CPB). Methods: Patients (n=120) were randomly assigned to an HHP and a control group. A safe inhaled oxygen fraction for the hypoxic preconditioning phase (10-14% oxygen for 10 minutes) was determined by measuring the anaerobic threshold. At hyperoxic phase, 75-80% oxygen fraction was used during 30 minutes. Results: The cumulative frequency of postoperative complications was 14 (23.3%) in the HHP vs 23 (41.1%), p=0.041. The nitrate decreased after surgery by up to 20% in the HHP group and up to 38% in the control group. Endothelin-1 and nitric oxide metabolites were stable in HHP but remained low more than 24 h in control group. The endothelial damage markers appeared to be predictors of postoperative complications. Conclusion: The HHP with individual parameters based on the anaerobic threshold is a safe procedure, it can reduce the frequency of postoperative complications. The endothelial damage markers appeared to be predictors of postoperative complications.

Objectives: Minimally invasive direct coronary artery bypass (MIDCAB) is an alternative for revascularisation of isolated left anterior descending (LAD) or as multi-vessel (MV) procedure for diagonal branch (RD) or circumflex artery (RCX) region. Methods: From 2021 to 2022 91 patients underwent MIDCAB procedure in our heartcenter. 80% were male. Eighty percent of the patients had two or three vessel coronary artery disease. Mean age was 65±10 years. The left internal mammary artery (LIMA) was anastomosed to the left anterior descending via left minithoracotomy approach in all patients. Fourteen patients received multi-vessel MIDCAB (15%) with two or three anastomoses a saphenous vein graft (as T-graft to LIMA) was anastomosed to RD or RCX. Results: Mean operation time was 2.6±0.8 hours. The 30-day mortality was 0. Mean required packed red blood cells (pRBC) was 0.4±1.2 unit. The intensive care unit stay (ICU) was 1.5±1.6 days mean. We observed two patients (2%) with wound infections postoperatively. Four patients underwent rethoracotomy because of bleeding. Mean follow-up time was 1.5±0.5 years. Seventy-eight patients (86%) were in New York Heart Association (NYHA) class 1, 11 patients (12%) were in NYHA class 2. One patient received percutaneous coronary intervention due to de novo stenosis of the RCA. Late mortality was 2%. The Kaplan-Meier survival rate was 98.8% at 1 and 2 years. Conclusion: MIDCAB is technically demanding. Our postoperative and short-term clinical results demonstrate that this procedure is safe and feasible. Optimal patient selection and an experienced surgical team are mandatory.

This paper seeks to model the crack propagation in of AAs (aluminum-alloys) 2524-T3 and 7050-T7452 subjected to fatigue loading at low temperature. Fatigue crack growth tests were performed on AAs 2524-T3 and 7050-T7452 subjected to constant-amplitude and actual random-spectra loading histories at room temperature of about 25 °C and at cryogenic temperature of -70 °C, respectively, to determine their crack growth properties and residual lives. The interaction mechanisms between cryogenic temperature and the fatigue load were deduced on the basis of the results of fractographic analysis. Temperature-dependent residual lives under actual random-spectrum load history were modeled based on a modified accumulation damage rule by accounting for the load interaction. Good correlation was achieved between the predictions and actual experiments, demonstrating the practical and effective use of the proposed method.

Attribute reduction is a core technique in the rough set domain and an important step in data preprocessing. Researchers have proposed numerous innovative methods to enhance the capability of attribute reduction, such as the emergence of multi-granularity rough set models, which can effectively process distributed and multi-granularity data. However, these innovative methods still have many shortcomings, such as how to deal with complex constraints and how to perform multi-angle effectiveness evaluations. Based on the multi-granularity model, this study proposes a new method of attribute reduction, namely using multi-granularity neighborhood information gain ratio as the measurement criterion. This method combines both supervised and unsupervised perspectives, and by integrating multi-granularity technology with neighborhood rough set theory, constructs a model that can adapt to multi-level data features. This model can select the optimal granularity level or attribute set according to the requirements. Finally, the proposed method is experimented with on 15 UCI datasets against six other attribute reduction algorithms. The experimental outcomes, upon analysis and comparative review, substantiate the reliability and consistency of the attribute reduction approach introduced in this study.

Background: Since the previous study dealing with the case fatality ratio and infection fatality ratio caused by COVID-19, the author has received many comments that prompted the question: "Why did an optimistic prognosis fail?" To answer this question, a more detailed and expanded analysis was carried out in a new study. Objective: To evaluate the dynamics of monthly numbers of cases, deaths, tests and CFR worldwide during three phases of the COVID-19 pandemic. Material and Methods: Twenty three sets of databases, dated the 22nd of each month from January 2020 to November 2021, for 213 countries were collected from the Worldometer website. The number of cases, deaths, tests, CFR, IFR, etc. were counted for various periods of time for each of the 213 countries, then results related to different periods of time were compared. Results: The analysis of the main epidemiological parameters led to the division of three phases of the global pandemic evolution. The first phase (23.01.20-22.07.20), the second phase (23.07.20-22.01.21) and the third phase (23.01.21-22.07.21) were different in terms of the number of tests performed, new cases, and mortality due to COVID-19. By the end of the second phase, the worldwide statistics indicated the imminent end of the pandemic, but the third phase was characterized by a sudden rise in the number of new cases and deaths that could not be explained rationally. The most dramatic evolution of the epidemic curve occurred in the countries where doctors had successfully battled COVID-19 during the first two phases of the pandemic. Conclusions: Despite the decrease in overall death numbers during the latest months analyzed, additional study is necessary to identify the cause for the increase in the number of new cases and deaths during the third phase of the pandemic. Only complete information regarding the positive and negative impact of medical and non-medical methods of diagnostics and prophylaxis of COVID-19 can help to organize effective measures to end the current pandemic and prevent a similar one from occurring in the future. Presumably, there are several causes of the negative evolution of the current pandemic, including the overreliance on PCR tests, application of non-specialized premises for quarantine and treatment, decrease in herd and individual immunity, inadequate change of therapeutic protocols, and ignoring prophylactic treatment. It can be suggested that the use of immunemodulatory drugs, for example, thymus extract or thymic peptides, in groups of people with compromised immunity is necessary, and prophylactic and therapeutic protocols should be changed from the 'standard' types to 'personalized' ones.

Preschoolers with disabilities and their caregivers have been neglected in health and social service provision in most low-income countries and arguably too in low resourced areas of more affluent nations. Yet as this rapid review of published literature identifies, there are low-cost, evidence-based strategies to address their needs that can be implemented in communities by local people. Five key features of the necessary supports are examined. First the leadership functions required to create and implement the support services. Second, the family-centred, home-based support provided to caregivers and the personnel undertaking this form of support. Third, providing opportunities for peer support to flourish and encouraging the formation of advocacy groups across families. Fourth, mobilizing the support of significant groups within the community; notably traditional healers and leaders; health services and poverty alleviation initiatives. Fifth, devising ways in which preschool educational opportunities can be offered to children as a prelude to their inclusion in primary schools. The review serves a further purpose. It provides an example of how public health researchers and academics could achieve more rapid implementation of evidence-based knowledge into existing and new support services through dissemination to community practitioners.

Objective: We report a case of acute pancytopenia and liver injury after concomitant administration of low-dose methotrexate (MTX), and high-dose esomeprazole and metamizole. Case summary: A 71-year-old patient with chronic systemic idiopathic erosive arthritis was admitted after a pelvic ring fracture. After hospital admission, she received MTX in addition to esomeprazole and metamizole. Subsequent laboratory tests revealed pancytopenia and elevated liver enzymes. The follow-up clinical examinations were unremarkable, with the exception of sub-febrile temperatures. Further investigations did not detect a definitive etiology. Due to the suspicion of methotrexate-induced hematotoxicity and hepatotoxicity, antagonizing therapy with calcium folinate was administered, after which the blood counts and liver parameters normalized. Discussion: Due to the administration of high-dose metamizole immediately before the administration of low-dose MTX, the pre-existing hematotoxic pharmacodynamic effect of MTX was acutely enhanced by that of metamizole, although folic acid was administered preemptively. In addition, the concomitant administration of high-dose esomeprazole and normal dose torasemide resulted in a pharmacokinetic interaction with MTX by decreasing its renal secretion and elimination, further enhancing the concentration-dependent hematotoxic and hepatotoxic side effects of MTX. Conclusions: The relatively high demand for analgesics in patients with chronic rheumatic diseases already being treated with MTX and proton pump inhibitors necessitates that clinicians consider drug-drug interactions as potential causes of adverse drug reactions after the administration of metamizole or nonsteroidal anti-inflammatory drugs. In this category of patients, it is strongly recommended to switch to analgesics of other classes.

Activities in the digital economy driven by information technology have rapidly increased in scope and speed in the aftermath of COVID-19. Meanwhile, social isolation accelerated by quarantine measures has increased concerns about individuals’ mental health. However, little is known about the specific consequences of online interactions, especially when applied in online fan community-based relationships where loyal community members are prevalent. Therefore, we examined whether a sense of virtual community (SOVC) can link fans’ online activities with their mental well-being and behavioral loyalty to the platform. For this purpose, we focus on BTS fandom “Adorable Representative MC for Youth” (ARMY) behaviors and attitudes on the fan community platform Weverse. With 202 valid data samples acquired from global ARMY, this study conducted a partial least squares–structural equation modeling analysis. The empirical findings reveal that SOVC in Weverse is significantly influenced by the intensity of online interactions with other fans and parasocial relationships with celebrities. SOVC is found to be the direct predictor of fans’ behavioral loyalty and mental well-being. When considering fans’ perceptions of other social media platforms, dissatisfaction with previous online fan communities enhances the intensity of online interactions with other fans in Weverse.

Leucokinins (LKs) constitute a neuropeptide family first discovered in a cockroach and later identified in numerous insects and several other invertebrates. The LK receptors are only distantly related to other known receptors. Among insects, there are many examples of species where genes encoding LKs and their receptors are absent. Furthermore, genomics has revealed that LK signaling is lacking in several of the invertebrate phyla and in vertebrates. In insects, the number and complexity of LK expressing neurons vary, from the simple pattern in the larva of Drosophila where the entire CNS has 20 neurons of three main types, to cockroaches with about 250 of many different types. Common to all studied insects is the presence or 1-3 pairs of LK-expressing neurosecretory cells in each abdominal neuromere of the ventral nerve cord, that, at least in some insects, regulate secretion in Malpighian tubules. This review summarizes the diverse functional roles of LK signaling in insects, as well as other arthropods and mollusks. These functions include regulation of ion and water homeostasis, feeding, sleep-metabolism interactions, state-dependent memory formation, as well as modulation of gustatory sensitivity and nociception. Other functions are implied by the neuronal distribution of LK, but remain to be investigated.

Single-phase-to-ground fault in non-effectively grounded systems poses serious public safety concern. Along with increasing deployment of low-voltage (LV) sensors, new opportunities and ways are created for solving this traditional problem in distribution systems. A new approach, identifying primary single-phase-to-ground line fault and locating it through measurement data from smart sensors deployed in the secondary side of distribution transformers, is proposed in this paper. When a fault occurs in primary distribution feeder, the transient aerial mode voltage (AMV) of each LV smart sensor is calculated. The fault line can be identified by an abrupt change value of AMV at LV side. Next, by finding the position of the maximum value of this AMV from LV sensors on the fault line, the fault location can be pinpointed to two neighboring distribution transformers. The proposed method has been proven to be efficient and reliable by simulation studies.

The increasing regulatory pressure to monitor and reduce GHG emissions and air pollutants requires cost-effective methods for their surveillance. The most common technique used for scientific investigations on gas concentration monitoring in barns are accurate but expensive and with a complex maintenance. This research study analysed the potential use of a low-cost portable measurement devices for the measurement of ammonia (NH3) and carbon dioxide (CO2) concentrations in an open dairy barn. A comparison between gas concentrations acquired at different heights from the floor by using portable devices and those acquired by a photoacoustic infrared multigas spectroscope (i.e., reference measurement) in the same sampling locations was carried out to determine the precision of the low-cost portable devices. The performance of low-cost portable devices was statistically analysed by the application of the one-way analysis of variance, correlation analysis and regression analysis. The results showed a significant difference between gas concentration values at various heights from the floor for both NH3 and CO2. The correlations between concentrations acquired by the low-cost portable device and the INNOVA were statistically significant (r=0.83; P&lt;0.001) for gas concentrations monitored at 0.4 m from the floor. Compared with the reference measurement device, the low-cost devices were effective in the monitoring of NH3 concentrations at 0.40 m from the floor though it underestimated them in the barn at increasing of the height from the floor, whereas the device was not adequate for CO2 concentrations. In detail, the relative measurement error of the low-cost devices compared to INNOVA was reduced close to the floor during NH3 concentration measurements. Within these limitations, this device could be useful for monitoring NH3 concentration in the barn and to assess variation in NH3 concentrations mainly related to the animal occupied zone. Further efforts are needed in this field of research to identify low-cost device that could simplify emission estimation from open dairy barns.

New innovative green concepts in electrified vertical take-off and landing vehicles currently emerge as a revolution to urban mobility going into the third dimension (vertically). The high population density of cities makes the market share highly attractive while posing an extraordinary challenge for community acceptance due to the increasing and possibly noisier commuter traffic. In addition to passenger transport, package deliveries to customers by drones may enter the market. The new challenges associated with this increasing transportation need in urban, rural and populated areas pose challenges for established companies and startups to deliver low-noise emission products. The article's objective is to revisit the benefits and drawbacks of an affordable acoustic measurement campaign focused on early prototyping. In the very early phase of product development, often considerably limited resources are available. With this in mind, the article discusses the sound power results using the enveloping surface method in a typically available low-reflection room with a reflecting floor according to DIN EN ISO 3744:2011-02. The method is applied to a subsonic electric ducted fan (EDF) unit of a 1:2 scaled electrified vertical take-off and landing vehicle. The results show that considerable information at low costs can be gained for the early prototyping stage, despite this easy-to-use, easy-to-realize, and not fine-tuned measurement setup. Furthermore, the limitations and improvements to a possible experimental setup are presented to discuss a potentially more ideal measurement environment. Measurements at discrete operating points and transient measurements across the total operating range were conducted to provide complete information on the EDF's acoustic behavior. The rotor-self noise and the rotor-stator interaction were identified as primary tonal sound sources, along with the highest broadband noise sources located on the rotor. Based on engineering experience, a first acoustic improvement treatment is also quantified with a sound power level reduction of 4dB(A). In conclusion, the presented method is a beneficial first measurement campaign to quantify the acoustic properties of an electric ducted fan unit at minimal resources in a reasonable time of several weeks when starting from scratch.

Topography represented by high resolution digital elevation models are able to inform past and present morphological process on the terrain. High resolution LiDAR data taken by the General Directorate of Map at the surroundings of the Bergama city shows great opportunities to understand the morphological process on alluvial fan on which the city is located and the flood plain of Bakırçay river near the alluvial fan. In this paper the LiDAR data collected in 2015 have been used to create DEM’s to understand the geomorphological evolution of the alluvial fan and the flood plain around it. Since the proximal roots and medial parts of the alluvial fan have been the scene for a long human settlement most topographical traces of the morphological process have been distorted. Nevertheless, the traces of past and present morphological process at the distal fan which consist the contact zone with the flood plain are very clear on the DEM created from LiDAR data. The levees and some old courses of Bergama and Bakırçay rivers have been shown on the maps which are also important to understand the ancient roads which follows these levees.

Abstract: Efforts for carbon emission reduction have been identified as a major climate change mitigation target in the Paris Agreement. The 26th Conference of Parties to the United Nations Framework Convention on Climate Change highlighted the worldwide effort for cleaner and greener mining, urging the mineral industry to embrace greener operational emissions reduction technologies and strategies. Ghana pledged at the Paris Conference to reduce CO2 emissions by 15% and increase renewable energy share to 10% of the national energy mix. Here the fundamental question is how Ghana’s mining industry can contribute to CO2 emission reduction efforts. This paper investigates barriers to low-carbon emission policy implementation among mining companies in Ghana. The questionnaire survey was conducted among Ghana’s four large-scale gold mining companies. As the sample number of available companies is limited, we used a descriptive analysis to assess the responses. The results show that the companies expressed widely different ways to respond to the issues of cost, a government policy/regulations for carbon emission reduction, and the adoption/acquisition of low-carbon technologies. Those companies that are relatively less prepared for this endeavor emphasized the uncertainties of securing sufficient energy in case of using low-carbon technologies. They also expressed a need for more trained workers to handle low-carbon technologies. All companies agreed with a expected high cost of adopting low-carbon options. There was a communication gap with the relevant government ministry about low-carbon mining options where the government should be able to facilitate the involvement of othe low technology providers, such as solar PV installation.

In this perspective article, we ponder topographical enhancements of artificial neural networks. In our recent paper in JMLR, we proved a quasi-equivalence between the network width and depth and also discussed the power of intra-links, which can be viewed as network height. In 1982, Hopfield published a network to model human associative memory, which contains many loops for dynamic evolution toward fixed points. Based on noising-denoising loops, diffusion models are recently developed to enable Bayesian modeling and inference with big data. Furthermore, we envision development of multi-AI-agent systems through “netware” engineering as a quantum leap of software engineering for emergent behaviors and autonomous AI at individual and population levels. We believe that the novel use of links and loops in space and time via multi-scale coupling would catalyze the next-generation neural networks.

Air passenger traffic prediction is crucial for the effective operation of civil aviation airports. Despite some progress in this field, the prediction accuracy and methods need further improvement. This paper proposes an integrated approach to the prediction of air passenger index as follows. Firstly, the air passenger index is defined and classified by the K-means clustering method. Based on the mutual information (MI) principle, the information entropy is used to analyze and select the key influencing factors of air passenger travel. By incorporating the MI principle into the support vector regression (SVR) framework, this paper presents an innovative MI-SVR machine learning model used to predict the air passenger index. Finally, the proposed model is validated by passenger throughput data of the Shanghai Pudong International Airport, China. The experimental results prove the model feasibility and effectiveness by comparing them with conventional methods, such as ARIMA, LSTM, and other machine learning models, outperformed by the MI-SVR model. Besides, it is shown that the prediction effect of each model could be improved by introducing influencing factors based on mutual information. The main findings are considered instrumental to the airport operation and air traffic optimization.

Air passenger traffic prediction is crucial for the effective operation of civil aviation airports. Despite some progress in this field, the prediction accuracy and methods need further improvement. This paper proposes an integrated approach to the prediction of air passenger index as follows. Firstly, the air passenger index is defined and classified by the K-means clustering method. Based on the mutual information (MI) principle, the information entropy is used to analyze and select the key influencing factors of air passenger travel. By incorporating the MI principle into the support vector regression (SVR) framework, this paper presents an innovative MI-SVR machine learning model used to predict the air passenger index. Finally, the proposed model is validated by passenger throughput data of the Shanghai Pudong International Airport, China. The experimental results prove the model feasibility and effectiveness by comparing them with conventional methods, such as ARIMA, LSTM, and other machine learning models, outperformed by the MI-SVR model. Besides, it is shown that the prediction effect of each model could be improved by introducing influencing factors based on mutual information. The main findings are considered instrumental to the airport operation and air traffic optimization.

The cuttlebone-like structure is a complex porous bionic structure with asymmetric sinusoidal S-shaped wall structure connecting laminar septa, and studies have shown that the cuttlebone-like structure has light weight, high strength and excellent energy absorption capability. It has become an important research to investigate the mechanical mechanism of cuttlebone-like structure and to design a bionic structure beyond nature structure based on it. In order to investigate the mechanical properties of the static compression and shearing processes of the cuttlebone-like structure, this paper establishes theoretical formulas and analyzes the influence of dimensionless parameters such as height-to-thickness ratio $\lambda$, period-to-thickness ratio $\xi$ and amplitude to period ratio $\eta$ on the compression and shearing processes with the help of ABAQUS finite element software.The parameter sensitivity analysis method was used to compare the important influence degree of each dimensionless parameter on the mechanical properties of the structure and to determine the relative optimal parameters of the structural mechanical properties under compression and shearing. Based on the relatively optimal parameter of the cuttlebone-like structure, the cross-sectional geometry of the structure is improved to build a new cuttlebone-like structure.The experimental results showed that the new cuttlebone-like structure with revised cross-section improved the mechanical properties of the cuttlebone-like structure.The study results are of theoretical guidance to enhance the mechanical properties and geometric design of cuttlebone-like structures.

A Systemic Lupus Erythematosus (SLE) is a prototypical systemic autoimmune disease characterized by a complex interplay of genetic, molecular, and cellular factors. It is considered a multifactorial disorder influenced by genetic susceptibility, environmental triggers, and dysregulated immune responses. Understanding the molecular and cellular mechanisms driving SLE pathogenesis has been instrumental in developing targeted therapies to manage the disease and improve patient outcomes. In this essay, we will delve into the intricate molecular and cellular processes underlying SLE and examine the key lessons learned from human therapies.

Mangroves offer vital ecological advantages including air and water filtration, coastal and estuarine habitat provision, sediment stabilization, and wave energy absorption. Their intricate root systems play a key role in safeguarding shorelines from tsunamis and erosive storms by dissipating wave energy. Moreover, mangroves shield against boat wakes and wind-waves, bolstering shoreline defense. Wave dissipation is a function of forest width, tree diameter, and forest density. Restoration efforts of juvenile mangroves in Florida’s Indian River Lagoon (IRL) aim to reduce wave energy in areas vulnerable to erosion. Physical model testing of wave dissipation through mangroves is limited due to the complexity in representing the mangrove structure, where prop roots are non-uniform in both diameter and location. Previous studies have quantified wave dissipating effects through use of scaled and parameterized mangrove structures. This study measures the dissipation effects of live mangroves in a wave flume, forced by conditions representative of the IRL. These measurements are used to validate a parameterized dowel model. Error between wave attenuation factors for the live mangrove and dowel system was on average 2.5%. Validation of the modularized dowel system allowed for further parameterized testing to understand forest structure effects, such as sediment stabilization and wave attenuation.

Recent advances in differential topology single out four-dimensions as being special, allowing for vast varieties of exotic smoothness (differential) structures, distinguished by their handlebody decompositions, even as the coarser algebraic topology is fixed. Should the spacetime we reside in takes up one of the more exotic choices, and there is no obvious reason why it shouldn't, apparent pathologies would inevitably plague calculus-based physical theories assuming the standard vanilla structure, due to the non-existence of a diffeomorphism and the consequent lack of a suitable portal through which to transfer the complete information regarding the exotic physical dynamics into the vanilla theories. An obvious plausible consequence of this deficiency would be the uncertainty permeating our attempted description of the microscopic world. We tentatively argue here, that a re-inspection of the key ingredients of the phenomenological particle models, from the perspective of exotica, could possibly yield interesting insights. Our short and rudimentary discussion is qualitative and speculative, because the necessary mathematical tools have only just began to be developed.

It is well known but under-appreciated in astrophysical applications, that it is possible for gravity to take on a life of its own in the form of Weyl-curvature-only metrics (note we are referring to the Weyl-only solutions of ordinary General Relativity, we are not considering Weyl conformal gravity or any other modified gravity theories), as numerous examples demonstrate the existence of gravitational fields not being sourced by any matter. In the weak field limit, such autonomous gravitational contents of our universe manifest as solutions to the homogeneous Poisson's equation. In this note, we tentatively explore the possibility that they may perhaps account for some phenomenologies commonly attributed to dark matter. Specifically, we show that a very simple solution of this kind exists that can be utilized to describe the rising tails seen in many galaxy rotation curves, which had been difficult to reconcile within the cold dark matter or modified Newtonian dynamics frameworks. This solution may also help explain the universal $\sim 1$Gyr rotation periods of galaxies in the local universe.

Semantic communication is not obsessed with improving the accuracy of transmitted symbols, but is concerned with expressing the desired meaning that the symbol sequence exactly carried. However, the generation and measurement of semantic messages are still an open problem. Expansion combines simple things into complex systems and even generates intelligence, which is consistent with the evolution of the human language system. We apply this idea to semantic communication system, quantifying and transmitting semantics by symbol sequences, and investigate the semantic information system in a similar way as Shannon did for digital communication systems. This work was the first to propose the concept of semantic expansion and knowledge collision, which may provide a new paradigm for semantic communications. We believe that expansion and collision will be the cornerstone of semantic information theory.

In foggy weather scenarios, the scattering and absorption of light by water droplets and particulate matter cause object features in images to become blurred or lost, presenting a significant challenge for target detection in autonomous driving vehicles. To tackle this problem, this study proposes a foggy weather detection method, YOLOv5s-Fog, based on the YOLOv5s framework. The model enhances the feature extraction and expression capabilities of YOLOv5s by introducing a novel target detection layer, SwinFocus. Additionally, this research incorporates decoupled head into the model and replaces the conventional non-maximum suppression method with Soft-NMS. Experimental results demonstrate that these improvements effectively enhance the detection performance for blurry objects and small targets in foggy weather conditions. Compared to the baseline model YOLOv5s, YOLOv5s-Fog achieves a 5.4% increase in mAP on the RTTS dataset, reaching 73.4%. This method provides technical support for rapid and accurate target detection in adverse weather conditions, such as foggy weather, for autonomous driving vehicles.

The emergence of Artificial Intelligence (AI) driven Keyword Spotting (KWS) technologies has revolutionized human to machine interaction. Yet, the challenge of end-to-end energy efficiency, memory footprint and system complexity of current Neural Network (NN) powered AI-KWS pipelines has remained ever present. This paper evaluates KWS utilizing a learning automata powered machine learning algorithm called the Tsetlin Machine (TM). Through significant reduction in parameter requirements and choosing logic over arithmetic based processing, the TM offers new opportunities for low-power KWS while maintaining high learning efficacy. In this paper we explore a TM based keyword spotting (KWS) pipeline to demonstrate low complexity with faster rate of convergence compared to NNs. Further, we investigate the scalability with increasing keywords and explore the potential for enabling low-power on-chip KWS.

In the diagnosis of olfactory neuroblastoma (ONB), the presence of S-100–positive sustentacular cells surrounding the tumor is important; however, these are also present in normal nasal sinus epithelium. Although ONB often has a different final diagnosis, complete resection of the tumor has a good prognosis and minimally affects the patient's treatment plan. When the tumor extends around the internal carotid artery (ICA), complete resection is difficult due to the high risk of vascular injury; revascularization using a high-flow bypass can avoid this complication. In the present case, the tumor was located in the left sphenoid sinus and extended around the ICA. Preoperative biopsy tissue was positive for neuroendocrine markers and slightly positive for S-100 protein, leading to a diagnosis of ectopic ONB. High-flow bypass revascularization with trapping of the ICA allowed complete tumor resection. The postoperative histopathological diagnosis was neuroendocrine carcinoma, showing no S-100 protein–positive cells. There was no sign of recurrence two and a half years after surgery without additional treatment. This case demonstrates that the presence of S-100 protein–positive cells in ONB may be misleading. Although misdiagnosis of ectopic ONB should be anticipated, a complete resection of the tumor is an effective treatment strategy.

An energy model that correlates fan airflow, head, speed, and system power input is essential to detect device faults and optimize control strategies in fan systems. Since the application of variable frequency drives (VFDs) makes the motor efficiency data published by manufacturers inapplicable, the fan efficiency and drive (belt-motor-VFD) efficiency must be identified for each individual system to obtain accurate energy models. The objectives of this paper are to identify an energy model of existing VFD-motor-fan systems using available experimental data and demonstrate its applications in loose belt fault detection and virtual airflow meter development for optimal control. First, an approach is developed to identify the fan head, fan efficiency and drive efficiency curves using available fan head, speed, and system power input as well as temporarily measured airflow rate without measuring shaft power. Then the energy model is identified for an existing VFD-motor-fan system. Finally, the identified model is applied to detect the slipped belt faults and develop the virtual airflow meter. The experiment results reveal that the developed approach can effectively obtain the energy model of VFD-motor-fan systems and the model can be applied to effectively detect slipped belt faults and accurately calculate the fan airflow rate.

Sphalerite has been recognized as the most important carrier of critical metal of Indium (In) due to that In mainly exists in the sphalerite lattice by isomorphic substitution. There are two significant replacing schemes for In entry into sphalerite, these are, Ag++In3+→2Zn2+ and Cu++In3+→2Zn2+. In order to understand the reaction process and constraints of the two substitution schemes, this paper uses first-principles methods to calculate In and Ag, Cu replacing Zn in sphalerite. According to the substitution schemes of Ag++In3+→2Zn2+ and Cu++In3+→2Zn2+, two doped sphalerite systems of Zn30InAgS32 and Zn30InCuS32 were constructed using 2×2×2 supercell model of sphalerite. Firstly, the pressure is controlled to 30MPa, and the temperature is set from 20-40MPa to simulate the response of the two doped sphalerite systems to temperature; Then, the control temperature was unchanged to 600K, and the pressure was set from 20-40MPa to investigate the pressure control of the two doped sphalerite systems. The lattice parameters, substitution energy, electronic structure, and population analysis of the designed models before and after replacement have been critically compared. The main conclusions can be drawn that it is more stable for In to enter sphalerite via the coupled substitution scheme Cu++In3+→2Zn2+, and the conditions that the two substitution schemes most likely to occur are 650K and 40MPa. This study not only reveals the physical and chemical properties of In-rich sphalerite formed by the two reaction processes of Ag++In3+→2Zn2+ and Cu++In3+→2Zn2+, but also has a certain enlightenment effect on the search for indium in sphalerite, and promotes the application of first principles in mineralization analysis.

Plant-microbe interactions are essential for ecosystem health and agricultural productivity. Metabolomics has revolutionized our understanding of these interactions by providing powerful methods to decipher the complex chemical signals involved. This review highlights the various metabolomics techniques used to study plant-microbe interactions, such as mass spectrometry, nuclear magnetic resonance spectroscopy, and advanced imaging technologies. We also discuss the role of contemporary bioinformatics tools, extensive databases, and the increasing influence of artificial intelligence and machine learning in the analysis of metabolomics data. Integrating metabolomics with other omics fields, including transcriptomics, proteomics, and metagenomics, allows for a comprehensive understanding of the molecular mechanisms underlying plant-microbe interactions. The review emphasizes the significance of fluxomics in elucidating the dynamic nature of metabolic networks. While there are challenges in data analysis, integration, and interpretation, metabolomics has profoundly expanded our knowledge of the role metabolites play in shaping plant-microbe interactions. As metabolomics technologies advance and integrate further with other omics approaches, we anticipate groundbreaking discoveries that will provide deeper insights into these complex interactions, ultimately leading to innovative strategies for sustainable agriculture and biotechnology.

Cooling fans are one of the critical components of air-forced (AF) dry-type transformers for regulating internal temperatures. Therefore, effective malfunction detection is crucial to maintain the transformer temperature within an acceptable range and prevent overheating. Regular maintenance occurs periodically and issues with cooling fans may arise between maintenance periods, leading to prolonged operation under malfunctioning conditions and potential failures. In addition, utilities typically have online information about whether a fan works or not without providing information about cooling fan malfunctioning circumstances. To address these challenges, this study proposes learning-based online monitoring techniques to detect malfunctions in AF transformer cooling fans. Random forests (RFs) and convolutional neural networks (CNNs) are developed to classify the audio signals from cooling fans into normal and malfunctioning classes. Unlike RFs, which require separate feature extraction, CNNs are trained based on spectrogram images derived from audio signals. Thus, various time-frequency techniques are utilized for feature extraction in RFs. Besides, multiple data augmentation techniques are employed to enhance the dataset size and diversity. Algorithmic performance is optimized through hyperparameter tuning and classifier threshold adjustment. Simulations reveal that CNNs outperform RFs, whereas the latter provides superior interpretability of acoustic features compared to the former.

Prediction of protein-ligand binding affinities is crucial for computational drug discovery. A number of deep learning approaches have been developed in recent years to improve the accuracy of such affinity prediction. While the predicting power of these systems have advanced to some degrees depending on the dataset used for model training and testing, the effects of the quality and quantity of the underlying data have not been thoroughly examined. In this study, we employed erroneous datasets and data subsets of different sizes, created from one of the largest databases of experimental binding affinities, to train and evaluate a deep learning system based on convolutional neural networks. Our results show that data quality and quantity do have significant impacts on the prediction performance of trained models. Depending on the variations in data quality and quantity, the performance discrepancies could be comparable to or even larger than those observed among different deep learning approaches. In particular, the presence of proteins during model training leads to a dramatic increase in prediction accuracy. This implies that continued accumulation of high-quality affinity data, especially for new protein targets, is indispensable for improving deep learning models to better predict protein-ligand binding affinities.

The excessive intake of sodium (Na) and insufficient intake of potassium (K) are major concerns to prevent hypertension. Using low-Na/K seasonings (reducing 25% of the NaCl and adding K salt) may improve the dietary Na/K ratio and help prevent hypertension. To devise an intervention study using low-Na/K seasonings at a company cafeteria, we calculated the Na and K contents of the meals served at the cafeteria and estimated changes in the intakes when suitable low-Na/K seasonings were used. We also considered using milk as a good source of K. We used an ingredient list of a company cafeteria and calculated Na and K contents in each dish. The average amounts of NaCl and K per use were 5.04 g and 718 mg, respectively. Seasonings contributed 70.9% of the NaCl. With the use of low-Na/K seasonings, an estimated reduction in NaCl of 0.8 g/day and an estimated increase in K of 308 mg/day was achieved. An additional serving (200 mL) of milk, NaCl was reduced by 0.57 g/day and K was increased by 610 mg/day, with an overall decrease in the dietary Na/K ratio from 3.20 to 2.40. The use of low-Na/K seasonings and dairy may improve the dietary Na/K ratio among cafeteria users and help prevent hypertension.

Ischemic stroke is one of the most disabling diseases and a leading cause of death globally. Despite advances in medical care, the global burden of stroke continues to grow, as no effective treatments to limit or reverse ischemic injury to the brain are available. However, recent preclinical findings have revealed the potential role of transient receptor potential cation 6 (TRPC6) channels as endogenous protectors of neuronal tissue. Activating TRPC6 in various cerebral ischemia models has been found to prevent neuronal death, whereas blocking TRPC6 enhances sensitivity to ischemia. Evidence has shown that Ca2+ influx through TRPC6 activates cAMP response element-binding protein (CREB), an important transcription factor linked to neuronal survival. Additionally, TRPC6 activation may counter excitotoxic damage resulting from glutamate release by attenuating the activity of NMDA receptors of neurons by posttranslational means. Unresolved though, are the roles of TRPC6 channels in non-neuronal cells such as astrocytes and endothelial cells. Moreover, TRPC6 channels may have detrimental effects on the blood-brain barrier, although their exact role in neurovascular coupling requires further investigation. This review discusses evidence-based cell-specific aspects of TRPC6 in the brain to assess the potential targets for ischemic stroke management.

Global warming poses a threat to plant survival, impacting growth and agricultural yield. Protein turnover, a critical regulatory mechanism balancing protein synthesis and degradation, is crucial for cellular response to environmental changes. We investigated the effects of elevated temperature on proteome dynamics in Arabidopsis thaliana seedlings using 15N-stable isotope labeling and ul-tra-performance liquid chromatography-high resolution mass spectrometry, coupled with the ProteinTurnover algorithm. Analyzing different cellular fractions from plants grown under 22°C and 30°C growth conditions, we found significant changes in the turnover rates of 571 proteins, with a median 1.4-fold increase, indicating accelerated protein dynamics under thermal stress. Notably, soluble root fraction proteins exhibited smaller turnover changes, suggesting tissue-specific adap-tations. Significant turnover alterations occurred with redox signaling, stress response, protein folding, secondary metabolism, and photorespiration, indicating complex responses enhancing plant thermal resilience. Conversely, proteins involved in carbohydrate metabolism and mito-chondrial ATP synthesis showed minimal changes, highlighting their stability. This analysis high-lights the intricate balance between proteome stability and adaptability, advancing our under-standing of plant responses to heat stress and supporting the development of improved thermo-tolerant crops.

Objective: The aim of this study was to evaluate the clinical outcome of patients suffering from chronic limb threatening ischemia (CLTI) and tissue loss treated with primary isolated femoral bifurcation endarterectomy (FBE) or with FBE combined with bypass surgery. Methods: This retrospective study was performed in a tertiary university based care center. Between January 2008 and December 2019 a prospectively collected database of patients suffering from CLTI and tissue loss and undergoing either primary FBE (group A) or FBE in combination with bypass surgery (group B) was analysed. Study endpoints were ulcer healing, primary and secondary patency rate, limb salvage and survival. Results: In total, FBE was performed in 73 and FBE with bypass in 60 patients. Between both groups there were no significant differences regarding demographic data or the Global Limb Anatomic Staging System (GLASS) grade III and IV of femoropopliteal lesions. After 3 years, ulcer healing could be achieved in 72% of FBE and in 75% of FBE with bypass patients. The primary patency rate was 95% and 91% for FBE and 83% and 80% for FBE with bypass after one and three years, respectively. The 3-year limb salvage rate was 78% for FBE and 84% for FBE with bypass. The secondary patency rate after one and three years was 99% and 97% for FBE and 93% and 88% for FBE with bypass. Conclusion: FBE and FBE with bypass are equally effective for ulcer healing in cases of combined CFA and superficial femoral artery lesions. There was no significant difference between both groups regarding primary and secondary patency

The properties of the annual, semiannual and triennial oscillations (AO, SAO and TO) in the middle atmosphere have been investigated using the TIMED/SABER temperature data. The Lomb-Scargle and wavelet spectra were used to determine the dominant oscillations in the background temperature field. The AO is prominent at the mid-latitudes. The AO amplitudes present an asymmetry between the two Hemispheres, being larger in the mesosphere than in the stratosphere. The SAO dominates the tropical regions, with three amplitude maxima at altitudes of 45, 75, and 85 km. The SAOs in the upper mesosphere (75 km) are out of phase with those in the mesopause (85 km) in the tropical regions, which can generate an enhancement of 11 K at each equinox, contributing to the lower mesospheric inversion layer. The TO is significant in the tropical region, with amplitude being maximum at 35, 45 and 85 km. Result shows that there may be potential interaction by the TO with SAO at 85km at the equator. The relation between ENSO and TO has also been discussed. The ENSO signal may modulate the amplitude of the TO, mainly in the lower stratosphere. The real origin of the TO may lie in the wave-mean-flow interaction.

A pilot study regarding the transplantation of 100 specimens of the critically endangered Pinna nobilis took place in summer of 2019 in Maliakos Gulf (Central Aegean, Greece). In this study we present the relationships between total height (HT, in cm), unburied length (UL, in cm), and shell width (SW, in cm) for P. nobilis and the relationship between HT and net weight (W, in g). Length-length relationships were all linear for all cases: r2 > 0.900), whereas the relationship between HT and W was exponential with the value of the exponent b being allometric. "Ecology, Conservation and Restoration of Threatened Animal"

As the first time, 0D-1D-3D and fully 3D steady-state aero-thermo-fluid simulations of a structural oil-to-air Fan Outlet Guide Vane Cooler (FOGVC) in a jet engine are presented. Using the commercial softwares Ansys Fluent, the thermo-mechanical module of Ansys and the 1D fluid solver Flownex, 5 simulation types (3D fully conjugate heat transfer with and without a thin wall model, 3D with a thin wall model, 1D-3D coupled, 1D and 0D) corresponding to 4 levels of simplification in 3 possible domains (oil, oil-metal and oil-metal-air) have been compared to provide selection criteria when a determined level of accuracy in the simulations without prohibited computational times is desired. The methodologies are applied to two different oil internal cavities: an inverted U with rectangular cross section and a coil internal cavity with a circular cross section. The obtained results show that depending on the scope of the research (outlet oil temperature, dissipated heat rate or oil pressure drop) and the accuracy of the results, one method or the other may be used. Experimental data would be needed to validate the numerical results by all employed methodologies and geometries.

With the development of higher voltage power grid, the high and low voltage parallel loops are emerging, which lead to energy losses, even threaten the security and stability of power system. The multi-infeed HVDC configurations widely appearing in AC/DC interconnected power system make this situation even worse. Aimed at energy saving and system security, a decision optimization method for power grid operating condition with high and low voltage parallel loops is proposed in this paper. Firstly, considering hub substation distribution and power grid structure, parallel loop opening schemes are generated with GN algorithm. Then, candidate opening schemes are preliminarily selected from all these generated schemes based on a filtering index. Finally, with the influence on power system security, stability and operation economy in consideration, an evaluation model for candidate opening schemes is founded based on analytic hierarchy process (AHP). And a fuzzy evaluation algorithm is used to find the optimal scheme. Simulation results of New England 39-bus system and an actual power system validate the effectiveness and superiority of this proposed method.

No-till and cereal-legume intercropping have been recognized as favorable cropping practices to increase crop yields while maintaining soil quality in arid and semiarid environment, but the bio-logical mechanisms are poorly understood. The present study was to determine the response of soil properties, enzyme activities, and microbial community diversity and composition in mono- and inter-cropping under conventional and no-tillage conditions. We initiated a field experiment in Wuwei, a typical arid area of China, in 2014. Soil was sampled in August 2022 and, yields, soil properties, enzyme activities, and the microbial community diversity and composition were de-termined in the maize and pea strips in inter- and mono-cropping systems. Results revealed that the maize and pea strips in the no-till intercropping significantly increased yields, total and or-ganic carbon stocks, decreased NO3--N, and obtained the highest total and organic P in the soil. The α- and β-diversity of archaea and eukaryotes were significantly affected by planting patterns, while α- and β-diversity of the bacterial community were significantly affected by tillage practices. Both no-tillage and intercropped maize significantly increased the abundance of archaea phylum Thaumarchaeota and bacterial phylum Nitrospirae, benefiting nitrogen fixation of intercropped pea from the atmosphere under the no-tillage cereal/legume intercropping. No-till intercropping was conducive to the accumulation of organic carbon, while decreasing the abundance of Prote-obacteria, Acidobacteria, and Verrucomicrobia. Limited soil enzyme activities (ACP, ALP, DP, NAG, BG, AG, CB) led to decreases in organic carbon turnover and utilization. Intercropping al-tered soil microbial community diversity and composition due to changes in soil properties and enzyme activities. These findings suggest that no-tilled cereal-legume intercropping is a sustaina-ble cropping practice for improving soil properties and enhancing microbial (archaea, bacterial, Eukaryota) diversity, but the long-term persistence is not conducive to rapid turnover of soil nu-trients due to limited enzyme activities.

Metabolic and bariatric surgery (MBS) is the most effective long-term treatment for Class III obesity. Reduced dietary intake is considered a behavioral driver of post-surgical weight loss, but limited data have examined this association. Therefore, this study examined prospective, longitudinal relationships between dietary intake and weight loss over 24 months following Roux-en-Y Gastric Bypass and Sleeve Gastrectomy. Relationships between weight loss and dietary intake were examined using a validated 24-hour dietary recall method. Associations between total energy/macronutrient intake and weight loss outcomes were assessed at 12-, 18-, and 24-months following MBS, defining patients as “responders” and “suboptimal responders” according to the Reinhold criteria of 50% excess weight loss. Consistent with previous literature, 12-month responders and suboptimal responders showed significant associations between weight loss and dietary intake. Unlike previous work, this study revealed that many of these associations are no longer significant 24 months post-MBS, despite consistent weight loss trends. This study suggests a short-term signal between these dietary factors and weight loss outcomes 12 months post-MBS, consistent with previous observations. However, this signal does not persist beyond 12 months. These results are essential for interpreting and designing clinical studies measuring long-term post-surgical weight loss outcomes.

Selected glasses with 10 Na₂O + (90-x) P₂O₅ + x BCD where bypass cement dust (BCD) x value =10, 20, 30 in mol% were synthesized by recognizable melting annealing technique. Cooperative characterization of the prepared glasses were carried out through FTIR and SEM analysis before and after immersed in simulated body fluid (SBF) solution for 13 and 23 days at 37 ^oC. After immersion in SBF, apatite layer is produced on the glass surface after 13 day and increase after 23 day, showing good bioactivity after immersion in the SBF especially for bioglass sample with 30% BCD. A porous hydroxy apatite layer produced on the surface of SBF-glass composite and this layer became denser after more soaking time, periods were extended from 13 to 23 days. Atomic absorption spectroscopy explained the early period of soaking that cause release of both Si and Ca ions through the glass beside decreasing of phosphrous ions. Bioglass (BCD-30) is studied as shielding for gamma, protons and alphas by using Phy-X software, SRIM Monte Carlo simulation code and its subroutine TRIM. The gamma shielding parameters, mass stopping power (MSP), range for both proton (H- ions) and alpha (He- ions) in bioglass- BCD-30 and human bone tissue have estimated. Also, comparison between them is calculated in predicting the radiation damage and atomic displacements per atom (dpa).

A single coronary artery is a very rare condition, commonly associated with other congenital anomalies. It could be generally classified as neither benign nor malignant form of congenital coronary artery anomalies since its pathophysiological and clinical implications grossly depend on different anatomical patterns defined by the site of origin and distribution of the branches. By presenting the patient with an isolated single coronary artery, who underwent successful combined aortic valve replacement and coronary artery bypass grafting surgery, we intend to distinguish casual from causal in this extremely rare clinical and surgical scenario. This is the first-ever case published, combining such underlying pathology, clinical presentation, and surgical treatment.