Dielectric elastomers, such as thermoplastic polyurethanes (TPU), are widely used as dielectric layer, emulation layer and substrate of flexible and stretchable devices. To construct capacitors and actuators that work stably upon deformation, it has become an urgent need to investigate the evolution of dielectricity under stress and strain. However, the lack of effective methods for estimating the dielectric constant of elastomers under strain poses a big challenge. This article reports a device for in-situ measuring the dielectric constant of TPU under strain. It is found that upon stretching TPU to a strain of 400%, its dielectric constant decreases from 8.47 to 2.94. In addition, combined Fourier-transform infrared spectroscopy, X-ray scattering technique, and atomic force microscopy have been utilized to characterize the evolution of microstructure under strain. The investigation under tensile strain reveals that a decreased density and average size of polarized hard domains, along with a tendency of the molecular chains to align in parallel with the tensile stress. The evolution of the microstructures results in a reduction of the dielectric constant parallel to the electric field in TPU. Our work provides valuable experimental reference for improving the stability of flexible sensors and actuators based on dielectric elastomers.

Yttria stabilized zirconia (Y-TZP) ceramics with drastically reduced yttria content have been introduced by different manufacturers aiming at improving the damage tolerance of ceramic components. In this study an alumina doped 1.5Y-TZP was axially pressed, pressureless sintered in air at 1250–1400 °C for 2 h and characterized with respect to mechanical properties, microstructure and phase composition. The material exhibits a combination of high strength of 1000 MPa and a high toughness of 8.5–10 MPa√m. The measured fracture toughness is, however, extremely depending on measurement protocol. Direct crack length measurements overestimate toughness due to trapping effects. The initially purely tetragonal material has a high transformability of > 80 %, the transformation behavior is predominantly dilatoric, measured R-curve related toughness increments are in good agreement with transformation toughness increments derived from XRD data.

Yttria stabilized zirconia materials are frequently used in mechanical engineering and biomedical applications. Demanding loading conditions require materials combining a high level of strength and fracture toughness. A ready to press alumina doped 2 mol% yttria stabilized zirconia powder was shaped by axial pressing and sintering in air at 1250 - 1500 °C for 2 h. The best combination of strength and toughness value of 7.8 MPa√m. Materials sintered in the middle of the chosen temperature range combine fully density, high transformability and small grain size. Toughness measurements by direct crack length measurements delivered unrealistically high fracture toughness values.

Despite polycarbonate (PC) being a widely used engineering plastic, its notch and crack sensitivity pose challenges in critical applications. To address this, PC was blended with elastomeric polymers to explore the improvement in toughness. This study systematically investigates the toughening mechanisms of PC blended with acrylonitrile-butadiene-styrene (ABS), copolyether ester elas-tomer (COPE), and ABS and styrene-ethylene-butylene-styrene (SEBS) copolymer grafted with maleic anhydride (MA). The morphology and mechanical behavior were evaluated under qua-si-static and high-speed tensile tests and Charpy impact tests using optical, electronic, and atomic force microscopy and Raman spectroscopy. The morphological analysis reveals cavitation and crazing phenomena for COPE and SEBS-g-MA systems, and mostly debonding for ABS, indicating an improvement in toughening. While the addition of ABS improves the PC plastic deformation, modifying ABS with maleic anhydride enhances the elastic modulus. Blending PC with SEBS-g-MA increases the strain at break, and the addition of COPE significantly improves the deformation behavior of PC (by around 115%). This comparative study provides valuable insights into the performance of different PC-elastomer blends under similar conditions, supporting the selection of appropriate materials for given applications.

The conservation of the main protease in viral genomes, combined with the absence of a homologous protease in humans, makes this enzyme family an ideal target for developing broad-spectrum antiviral drugs with minimal host toxicity. GC-376, a peptidomimetic 3CL protease inhibitor, has shown significant efficacy against coronaviruses. Recently, a GC-376-based PROTAC was developed to target and induce the proteosome-mediated degradation of the dimeric SARS-CoV-2 3CLPro protein. Extending this approach, the current study investigates the application of the GC-376 PROTAC to the 3CPro protease of Enteroviruses, specifically characterizing its interaction with CVB3 3CPro through X-ray crystallography, NMR and biophysical techniques. The present structural data show that there are some changes between the binding of CVB3 3CPro and SARS-CoV-2 3CLPro, but the overall similarity is strong. The most notable variation is the orientation of the phenylmethyl ester of GC-376 with the S4 subsite of the proteases. This is linked to the flexibility of the protein structure around the region of the catalytic triad shown by our NMR data. Other structural variations include distinct ligand interactions in subsites S1 and S2, influenced by the presence of Glu71 in CVB3 3CPro. Despite these differences, the GC-376 PROTAC fits well within the binding sites of both proteases, demonstrating its potential as a broad-spectrum antiviral agent.

In this study a material based on Polyethylene (PE) and Microcrystalline Cellulose (MC) was developed as a breathable packaging film. Surface functionalization of MC with 3 aminopropyltriethoxysilane (APTES) shows to be an efficient alternative to tailor their properties and increase opportunities for the application of MC on the reinforcement of polymers such polyethylene (PE). Functionalization of MC with mentioned silane derivative was achieved using a green method and later used on the development of composites with PE in three percentages (1, 3 and 5%). All the materials were prepared by melt blending and characterized, in terms of structural properties (ATR-FTIR and FTIR in transmittance, EDX, SEM), thermal properties (DSC and TGA), thermomechanical properties (DMA), contact angle measurements and permeability to oxygen and water vapor. The materials demonstrated to have potential to be used as breathable film packaging of fresh products.

The carbonyl iron particles were dispersed in a polychloroprene rubber (CR) matrix under an external magnetic field for practical application as microwave absorption composites film. The film prepared under external magnetic field with a thickness of only 0.54 mm showed least reflection loss of -15.98 dB and the reflection loss value less than -10.0 dB over the frequency range of 11.4~14.8 GHz. In comparison with the microwave absorption properties of calculation by transmission line theory based on the tested relative complex permittivity and permeability and film prepared by general route without external magnetic field, the film made with external magnetic field exhibited more excellent microwave absorption properties, strongly depending on the increment of anisotropy and rearrangement of magnetic particles. The results indicated the composite film made under external magnetic field have excellent microwave absorption properties, which suggest that the composites thin film could be used as a thinner and lighter microwave absorber.

Negative temperature coefficient (NTC) materials are usually based on ceramic semiconductors and electrons are involved in their transport mechanism. A new type of NTC material, adequate for alternating current (AC) applications, is represented by zeolites. Indeed, zeolites are single-charge carrier ionic conductors with a temperature-dependent electrical conductivity. In particular, electrical transport in zeolites is due to the monovalent charge-balancing cations, like K⁺, capable of hopping between negatively charged sites in the aluminosilicate framework. Owing to the highly non-linear electrical behavior of the traditional electronic NTC materials, the possibility to have alternative types of materials, showing linearity in the electrical behavior, is very desirable. Among different zeolites, the natural clinoptilolite has been selected for investigating the NTC behavior since it is characterized by high zeolite content, convenient Si/Al atomic ratio, good mechanical strength, due to its compact microstructure, and low toxicity. Clinoptilolite has shown a rapid and quite reversible impedance change under heating, characterized by a linear dependence on temperature. X-ray diffraction (XRD) has been used to identify the natural zeolite, to establish all types of crystalline phases present in the mineral, and to investigate the thermal stability of these phases up to 150°C. X-ray photoelectron spectroscopy (XPS) analysis has been used for the chemical characterization of the natural clinoptilolite sample, providing important information on the cationic content and framework composition. In addition, since electrical transport takes place in the zeolite free-volume, a Brunauer–Emmett–Teller (BET) analysis of the mineral has been also performed.

Hybrid organic/inorganic conducting and magnetic composites of core–shell type have been prepared by in-situ coating of nickel microparticles with polypyrrole. Three series of syntheses have been made. In the first, pyrrole was oxidized with ammonium peroxydisulfate in water in the presence of various amounts of nickel and the composites contained up to 83 wt% of this metal. The similar syntheses in 0.1 M sulfuric acid followed. Finally, the composites with polypyrrole nanotubes were prepared in water in the presence of structure-guiding methyl orange dye. FTIR and Raman spectroscopies confirmed the formation of polypyrrole. The resistivity of composite powders of the order of tens to hundreds Ω cm was monitored as a function of pressure up to 10 MPa. The resistivity of composites slightly increased with increasing content of conducting nickel. This apparent paradox is explained by the coating of nickel particles, which prevents their contacts and generation of metallic conducting pathways. Electrical properties were practically independent of the way of composite preparation or nickel fraction and were controlled by polypyrrole phase. On the contrary, magnetic properties were determined exclusively by nickel content. The composites were used as a solid phase to prepare a magnetorheological fluid. The test showed better performance when compared with a different nickel system.

Synthesis of biocompatible and bioresorbable composite materials such as “polymer matrix-mineral constituent,” which stimulate the natural growth of living tissues and the restoration of damaged parts of the body, is one of the challenging problems in regenerative medicine and material science. Composite films of bioresorbable polymer of polyvinylpyrrolidone (PVP) and hydroxyapatite (HA) were obtained. HA was synthesized in situ in a solution of polymer mixture. We applied electron paramagnetic resonance (EPR) and nuclear magnetic resonance (NMR) approaches to study their properties. EPR in two frequency ranges allowed to derive spectroscopic parameters of the nitrogen-based light and radiation-induced paramagnetic centers in HA, PVP and PVP-HA with high accuracy. It was shown that PVP did not significantly affect the EPR spectral and relaxation parameters of the radiation-induced centers in HA. Magic angle spinning (MAS) 1H NMR shows the presence of two signals at 4.7 ppm and -2.15 ppm attributed to “free” water and hydroxyl groups, while the single line - to 31P. NMR relaxation measurements for 1H and 31P show that the relaxation decays are a multicomponent process that can be described by three components of the transverse relaxation times. The obtained results demonstrated that the applied magnetic resonance methods can be used for the control of quality of the synthesis of the PVP-HA composites and, potentially, for the development of analytical tools to follow the processes of the sample treatment, resorption, and degradation.

Organically-coated nanomaterials are intensively studied and find numerous applications in a wide range of areas ranging from optics to biomedicine. One of the recent trends in material science is the application of bio-mimetic polydopamine coatings that can be produced on a variety of substrates in a cost-efficient way under mild conditions. Such coatings not only modify the biocompatibility of the material but also add functional amino groups to the surface that can be further modified by classic conjugation techniques. Here we show an alternative strategy of substrates modification using not dopamine but dopamine conjugates. Compared to the classic scheme the proposed strategy allows for separation of the "organic" and "colloidal" stages and simplifies identification and purification steps. Modification with pre-modified dopamine allowed to achieve high active components loading up to 10.5% wt. A series of organo-inorganic hybrids were synthesized and their bioactivity was analyzed.

Defectively manufactured and deliberately damaged composite laminates fabricated with different continuous reinforcing fibres (respectively, carbon and glass) and polymer matrices (respectively, thermoset and thermoplastic) were inspected in magnetic resonance imaging equipment. Two pulse sequences were evaluated during non-destructive examination conducted in saline solution-immersed samples to simulate load-bearing orthopaedic implants permanently in contact with biofluids. The orientation, positioning, shape, and especially the size of translaminar and delamination fractures were determined according to stringent structural assessment criteria. The spatial distribution, shape, and contours of water-filled voids were sufficiently delineated to infer the amount of absorbed water if thinner image slices than this study were used. The surface texture of composite specimens featuring roughness, waviness, indentation, crushing, and scratches was outlined, with fortuitous artefacts not impairing the image quality and interpretation. Low electromagnetic shielding glass fibres delivered the highest, while electrically conductive carbon fibres produced the poorest quality images, particularly when blended with thermoplastic polymer, though reliable image interpretation was still attainable.

Thermal camouflage is a highly sought-after technology to increase the survivability of military equipment against infrared (IR) detectors. Recently, two-dimensional (2D) nanomaterials have shown low IR emissivity, widely tunable opto-electronic properties and compatibility with stealth-applications. Among them, graphene and graphene-like materials are the most attractive 2D materials used for thermal camouflage applications. In particular, in multilayer graphene (MLG) charge density can be effectively tuned through sufficiently intense electric fields or through electrolytic gating. Therefore, MLG optical properties, like infrared emissivity and absorbance, can be controlled in a wide range by voltage bias. The large emissivity modulation achievable with this material makes it suitable in the design of thermal dynamic camouflage devices. Generally, the emissivity modulation in the multilayered graphene medium is governed by an intercalation process of non-volatile ionic liquids under a voltage bias. The electrically-driven reduction of emissivity leads to a decrease in the apparent temperature of the surface, which can match that of the background enabling thermal camouflaging. Since this property is common to other graphene-based materials, here we present a review specifically focused on the recent advances in the field of the thermal camouflage properties of graphene in the form of composite film and aerogel structures. A summary of the current understanding of the working principle of thermal camouflage materials, current limitations, and future opportunities is presented and discussed.

Recently, polyacetylene (PA) is receiving a renewed scientific attention due to its electrical properties potentially useful for energy applications (e.g., fabrication of electrodes for batteries and supercapacitors) and unique functional characteristics (e.g., flame retardant, oxygen scavenger, EMI-shielding, etc.). This chemical compound can be obtained in form of a polyacetylene-PVOH copolymers simply by chemical dehydration of poly(vinyl alcohol) (PVOH), which is a very common type of polymer, widely used in packaging and other technological areas. This very inexpensive chemical reaction for the large-scale synthesis of PA/polyvinylenes has been investigated by reacting PVOH with fuming sulfuric acid at room temperature. In this process, PVOH, shaped in form of film, is dipped in fuming sulfuric acid (i.e., H₂SO₄ at 95-97%) and, after complete chemical-dehydration, it has been mechanically removed from the liquid phase by using a nylon sieve. The reduction process leads to a substantial PVOH film conversion to PA as it has been proved by infrared spectroscopy (ATR-mode). Indeed, the ATR spectrum of the reaction product included all characteristic absorption bands of PA. The reaction product has been also characterized by UV-Vis spectroscopy in order to evidence the presence in the structure of conjugated carbon-carbon double bonds of various lengths. Differential scanning calorimetry (DSC) and thermogravimetric analysis have been used respectively to investigate the PA solid-state cis-trans isomerization and thermal stability in air and nitrogen, respectively.

Lipids have not traditionally been considered likely candidates for catalyzing reactions in biological systems. However, there is significant evidence that aggregates of amphiphilic compounds are capable of catalyzing reactions in synthetic organic chemistry. Here we demonstrate the potential for the hydrophobic region of a lipid bilayer to provide an environment suitable for catalysis by means of a lipozyme, or lipid aggregate capable of speeding up a chemical reaction. By bringing organic molecules into the non-polar or hydrophobic region of a lipid bilayer, reactions can be catalyzed by collections of small, nonpolar or amphiphilic molecules. We demonstrate this concept by the ester hydrolysis of calcein-AM to produce a fluorescent product, which is a widely used assay for esterase activity in cells. The reaction was first carried out in a two phase octanol-water system with the organic phase containing the cationic amphiphiles cetyltrimethylammonium bromide (CTAB) or octadecylamine. The octanol was then replaced with DOPC added to the water in the form of vesicles, where the reaction was also found to be carried out. The reaction was monitored using quantitative fluorescence which revealed catalytic turnover numbers on a scale of 10−4s−1 for each system, which is comparable to some slow enzymes. The reaction product was characterized by 1H-NMR measurements which were consistent with ester hydrolysis. The implications of thinking about lipid aggregates as catalytic entities are discussed in the context of biochemistry, pharmacology and synthetic biology.

This paper proposes an innovative approach to address the challenge of softening deformation of thermal-curable thermosets during additive manufacturing. This approach involves the development of a composite powder composed of thermosetting materials with distinct curing temperatures, the utilization of Cold Spray Additive Manufacturing (CSAM) technology for 3D printing, and the application of a stepwise isothermal curing process. The corresponding effectiveness is validated by case studies. The results demonstrate that samples printed via CSAM maintain a solid state without deformation. During the post-curing process, each component of the composite material cures independently while the other components remain in a solid state, providing structural support for the whole material, thereby effectively reducing the softening deformation during the post-curing process. This approach offers a novel perspective for the additive manufacturing of thermal-curable thermosets.

The development and improvement of methods for the synthesis of environmentally friendly catalysts based on base metals is currently an urgent and promising task of modern catalysis. Catalysts based on nanoscale magnetite and maghemite have fast adsorption-desorption kinetics and high chemical activity. The purpose of this work was to obtain magnetic composites, determine their physicochemical characteristics and verify their activity in the process of liquid-phase oxidation of phenol with oxygen. Magnetic nanocomposites were obtained by chemical co-deposition of salts of ferrous and trivalent iron. The synthesized magnetic composites were studied by X-ray diffractometry, energy dispersive X-ray fluorescence and Mössbauer spectroscopy, IR-Fourier spectroscopy, elemental analysis. To increase the catalytic activity in oxidative processes, the magnetite surfaces were modified using cobalt nitrate salt. Further, CoFe2O4 was stabilized by adding polyethylenimine (PEI) as a surfactant. Preliminary studies of the oxidation of phenol with oxygen, as the most typical environmental pollutant were carried out on the obtained Fe3O4, CuFe2O4, CoFe2O4/PEI catalysts. The spectrum of the reaction product shows the presence of CH in the aromatic ring and double C=C bonds, stretching vibrations of the C=O groups of carbonyl compounds; the band at 3059 cm–1 corresponds to the presence of double C=C bonds, the band at 3424 cm–1 hydroquinone compounds. The band at 1678 cm–1 and the intense band at 1646 cm–1 refer to vibrations of the С=О bonds of the carbonyl group of benzoquinone. Peaks at 1366 cm–1 and 1310 cm–1 can be related to the vibrations of C–H and C–C bonds of the quinone ring. Thus it was demonstrated that produced magnetic composites based on iron oxide are quite effective in the oxidation of phenol with oxygen.

The continuous casting process of helical fiber reinforced metal matrix composites was proposed, and the experimental equipment was designed and manufactured. The relationship model be-tween the process parameters and the helical shape of the fibers in the metal matrix is analyzed by differential geometry. Helical carbon fiber reinforced lead matrix composites were prepared under different conditions. When the melting temperature and cooling intensity were increased, the helical radius of helical carbon fiber in lead matrix was increased. When the fiber rotation speed was increased, the helical radius was decreased, and the helical pitch was de-creased proportionally. The experimental results are consistent with the process model. Carbon fiber rein-forced aluminum composites were prepared. Scanning electron microscopy showed that the infiltration between the aluminum matrix and the carbon fiber was not complete. As the volume fraction of carbon fiber which was added in composites is too small, the mechanical properties of the composites have not been significantly improved.

Porous hierarchical structure has been widely used in engineering for its high specific strength and stiffness, improved corrosion-resistance and multifunctionality. The design of multi-scale topology optimization for such structures has been a hot topic during the past two decades. In this paper, a new hybrid MMC-density topology optimization method of cellular structures with quasi-periodic microstructures is proposed. The so-called ‘quasi-periodic’ means the microstructures in different macro points have similar topology but with different parameters. The key idea is to describe the microstructural topology using MMC and describe the micro layout using the variable density. Sensitivities of the structural compliance with respect to the two types of design variables are derived and gradient optimization method is applied to update the design variables. The presented numerical examples show that the quasi-periodic cellular structures have better performance than single-scale structures and periodic cellular structures. Numerical examples demonstrate the effectiveness of the proposed approach.

(1) Background: A wide literature based on loading and unloading bending tests has been carried out over the half past century for assessing the force released by superelastic wires. The aim of this investigation is not only to characterize a broadly described superelastic NiTi and a novel CuNiTi archwire, but also to provide novel insights into the load vs deflection profiles. A harmonic scenario for superelastic wires will be shown as temperature is kept constant at 37°C. However, a completely different picture will be highlighted as a temporary heating step up to 50°C is introduced within the force vs deflection profiles. (2) Methods: A variety of NiTi and a novel CuNiTi round and rectangular cross-section archwires have been investigated. Static 3-point bending tests up to a deflection level of 3.0 mm have been carried out for detecting the unloading force plateau levels occurring at 37°C. A hold deflection step of 5 min at deflection levels occurring along the unloading plateau extension is introduced. The effect of a temporary heating up to 50°C on the force plateau level released by the investigated wires is analyzed. (3) Results: Mechanical profiles suggest that the plateau force levels detected at 37°C are consistent with those broadly reported in the literature, but they only represent a single block puzzle of the force scenario that a superelastic wire releases during the orthodontic treatment. (4) Conclusions: Once a superelastic wire is bent and clinically applied, the effect of a temporary heating up to 50°C (e.g. hot food or drink ingestion) produces a significant plateau force increase whose magnitude depends on the deflection level. The highest force increase of about 50% and 40% have been detected at deflection levels located at the beginning of the unloading plateau extension for NiTi and CuNiTi wires, respectively.

Considerable efforts have been made in recent years to identify an optimal treatment method for the removal of antibiotics from wastewaters. A series of supramolecular organic-inorganic magnetic composites containing Zn-modified MgAl LDHs and Cu-phthalocyanine as photosensitizer have been prepared with the scope to β-lactam antibiotics removal from aqueous solutions. The characterization of these materials confirmed the anchorage of Cu-phthalocyanine onto the edges of the LDH lamellae, with a negligible part inserted in the interlayer space. The removal of β-lactam antibiotics occurred via a concerted adsorption and photocatalytic degradation. The efficiency of the composites was depending on i) the LDH: magnetic nanoparticle (MP) ratio, that is strongly correlated to the textural properties of the catalysts, and ii) the phthalocyanine loading in the final composite. A maximum of the efficiency was achieved with a removal of ~93% of antibiotics after 2h of reaction.

Motivated by the PEACOC project on metal recovery from solid wastes, an innovative magnetic density separation (MDS) process has been developed for granular material sorting. It has intrinsic advantages over the existing industrialized MDS by eliminating fluid turbulence and particle jamming problems. The new MDS applies an inclined planar magnet and a horizontal basin containing a static magnetic fluid as the separation medium. A particle sliding phenomenon is identified as a feature of the process which could help the separation. The MDS successfully sorted shredded PCBAs to concentrate valuable metals and sorted shredded wires to reduce metallic contaminants in the plastic fractions. A pilot scale facility is introduced to show the design to achieve continuous production and to reduce the consumption of ferrofluid.

In this paper, a new axial-type magnetic gear with auxiliary flux-enhancing structure (AFS-AMG) is proposed. Compared to conventional AFS-AMG, it has the higher torque density and higher permanent magnet (PM) utilization factor. Firstly, the design rules and operating principles of proposed AFS-AMG are elaborated. Then, the mapping relation between the radial-type magnetic gears (RMGs) and AMGs are elucidated. Compared to its counterpart in RMGs, AFS-AMGs achieve small size. Then, the geometrical parameters of AFS-AMGs are optimized to obtain the better electromagnetic performances, where the torque density per volume and per PM volume is adopted as the evaluation standard. Finally, three different AMG topologies are constructed in finite element analysis (FEA) software for comparison. It is proven that the AFS-AMG has the largest torque density per volume and per PM volume.

This study provides an in-depth review of the available literature on metal composite material machining, focusing on traditional machining operations such as turning, milling, shaping, drilling, and grinding. The motivation for the study is that this composite type has emerged as a vital material in applications requiring functionality, resilience, cost-effective operation, low consumption of energy and lightweight. Despite its superior characteristics, the manufacturing complexity and poor machinability of metal matrix composites have been the primary barriers to its adoption. Nevertheless, there is a reduction of exceptional efficiency, increase in surface roughness, tool wear and so on in metal matrix composites throughout machining. As a result, this review gives a comprehensive investigation of metal matrix composite machining and effect on process parameters and procedures. Furthermore, this study distinguishes metal matrix composites towards sustainable manufacturing and the metals employed by the researchers, as well as the gaps discovered for future recommendations in metal-based composites.

In this project, four of fibers Bragg gratings were fabricated by injecting different volumes of liquids (star line Glass Mechanix optical adhesive material, olive oil diluted with ethanol) into the hollow core fiber. The amplitude splitting interferometric technique with a high resolution specially designed translation stage was used for the fabrication process. The fabrication was done using ultraviolet laser operated at wavelength 405nm. The fabricated Bragg length of the four fibers is equal to 3.8 cm. The results presented fiber Bragg grating (FBG) with successful fabrication at 653.3 nm Bragg reflected wavelength.

Boeing and Airbus developed a special testing procedure to investigate the compressive response of laminates that have been impacted (following standards ASTM D 7137 and DIN 65561). This study focuses on both experimental and numerical analysis of Kevlar plates subjected to compression after impact. To ensure high quality and appropriate mechanical properties, the composite plates were manufactured using autoclaving. The DIN 65561 protocol was followed for all three test systems. Initially, ultrasonic C-scanning was performed on all plates before testing to confirm they were free of any significant defects arising from the manufacturing process. Subsequently, low-energy impact testing was conducted at levels ranging from 0 to 8 Joules. Three specimens were tested at each energy level. After the impact, all specimens underwent ultrasonic C-scanning again to assess the internal delamination damage caused by the impactor. Finally, both pristine and impacted specimens were subjected to compressive testing using the special jig specified in DIN 65561. The compressive impact strength results obtained from these tests were plotted against the delamination area measured by C-scanning. This data was then compared to results obtained from specimens with artificial damage. Semi-empirical equations were used to fit both sets of curves. The same procedure (impact testing, C-scanning, and data analysis) was repeated to investigate the relationship between impact energy and total delamination area. Lastly, finite element modeling was employed to predict the buckling stresses that develop under compression in the impacted systems studied. These modelling approaches have demonstrated good accuracy in reproducing experimental results for CAI tests.

A comprehensive modeling framework for the thermoforming of polymer matrix woven laminate composite was developed. Two numerical indicators, the slip path length and traction magnitude, have been identified to be positively correlated to matrix smearing and wrinkling defects. The material model has been calibrated with picture-frame experimental results, and the prediction accuracy for intra-ply shear and thickness distribution were examined with measurements on the physically formed parts. Finally, a parametric study was conducted to determine the relationship between various process parameters and the quality of the formed part. For the trapezoidal part, orienting the laminate at 45-degrees to the mold axis reduces the likelihood of matrix smear and wrinkling defects. Although this laminate orientation yielded a greater spatial variation of part thickness, the thickness deviation is lower than that for the 0-degree orientation case. Higher forming rates were found to result in more defects due to increased slip path lengths and traction magnitudes. Optimal forming speeds should balance rapid shaping within the operating temperature window while avoiding tear. It was discovered that shallower molds benefit from faster ramp rates, while deeper molds require slower rates to manage extensive shearing, stretching, and bending. Faster forming rates lead to smaller thickness increases at high intra-ply shear regions, indicating a shift from intra-ply shear to out-of-plane bending due to the visco-plastic effect of the molten laminate, and can negatively impact part quality. Lastly, it was shown that a well-conceived strategy using darts could improve the part quality by reducing the magnitude of the defect indicators.

This review examines additive manufacturing for refractory tungsten (W) and its alloys. It emphasizes the primary challenges and determining factors involved in additive manufacturing pure W, W alloys, and composites. Our focus in this regard extends to both process and alloying strategies designed to address critical issues such as densification, micro-cracking, and mechanical properties in tungsten-based components produced through additive techniques. Throughout the review, we organize existing knowledge and insights into convenient tables, serving as valuable resources for researchers embarking on a deeper exploration of these topics.

Graphene hybrid-filler polymer composites have emerged as prominent materials that revolutionize heavy industries. This study encapsulates the in-depth analysis of different influential factors such as filler/graphene type, aspect ratios, dispersion methods, filler-matrix compatibility, fiber orientation, synergistic effects, different processing techniques, and post-curing conditions that affect the processing, properties and determine the resultant applications of graphene hybrid polymer composites. Additionally, it discusses the substantial role of graphene collaboration with other fillers such as carbon nanotubes, silica, nano-clays and metal oxides to produce functionalized hybrid polymer composites with synergistically enhanced tailored properties to offer solutions for heavy industries like aerospace, automotive, electronics, and energy harvesting. The review concludes with some suggestions and outlook on the future of these composite materials by emphasizing the need for continued research to fully optimize their potential.

The article offers a comprehensive overview of recent breakthroughs in eco-friendly polymers and polymer composites, underscoring their pivotal role in addressing sustainability challenges across diverse industrial sectors. Despite encountering obstacles related to performance and processability, biopolymers sourced from renewable materials emerge as promising alternatives for the plastics that are currently used by human beings. Natural fillers are highlighted as a strategic avenue for crafting sustainable composites, with residual natural fillers being particularly explored. Heightened environmental concerns propel discussions on the criticality of integrating biodegradable materials with natural fillers, underlining the urgency for clear frameworks and financial incentives to support adoption of these materials. Additionally, the article examines the potential of biodegradable polymers and polymer composites, with a specific emphasis on the utilization of polyhydroxyalkanoate (PHA) in composite materials and its market prospects. Moreover, it emphasizes the indispensable need for ongoing research and development endeavors to address environmental challenges within the polymer sector, reflecting a mounting interest in sustainable materials across industries.

This review is focused on the current status of quantitative MR (qMR) of skeletal muscle. The first section covers the techniques of qMR in muscle with the focus on each quantitative parameter, the corresponding imaging sequence, discussion of the relation of the measured parameter to underlying physiology/ pathophysiology, the image processing and analysis approaches, and studies on normal subjects. We cover the more established parametric mapping from T1 weighted imaging for morphometrics including image segmentation, proton density fat fraction, T2 mapping, diffusion tensor imaging to emerging qMR features such as magnetization transfer including ultralow TE imaging for macromolecular fraction, and strain mapping. The second section is a summary of current clinical applications of qMR of muscle; the intent is to demonstrate the utility qMR in different disease states of the muscle rather than a complete comprehensive survey.

This paper addresses a new micromechanical model to predict biaxial tensile moduli of plain weave fabric (PWF) composites by considering the interaction between the orthogonal interlacing strands. The two orthogonal yarns in micromechanical unit cell (UC) were idealized as the curved beams with a path depicted by using sinusoidal shape functions. The biaxial tensile moduli of PWF composites were derived by means of the minimum total complementary potential energy principle founded on micromechanics. The biaxial tensile tests were respectively conducted on the RTM-made EW220/5284 PWF composites at five biaxial loading ratios of 0, 1, 2, 3 and ∞ to validate the new model. The predictions from the new model were compared with experimental data and good correlation was achieved between the predictions and actual experiments, demonstrating the practical and effective use of the proposed model. Using the new model, the biaxial tensile moduli of plain weave fabric (PWF) composites could be predicted based only on the properties of basic woven fabric.

As the number of end-of-life vehicles continues to grow, the field of separation technology for broken copper and aluminium parts of end-of-life vehicles has emerged as a significant area of research. As a key technology for the separation of non-magnetic non-ferrous metals, such as copper and aluminium, eddy current separation can achieve efficient separation of non-magnetic non-ferrous metals according to their differing conductivity and density. Nevertheless, further research is required in the separation of large-scale broken copper and aluminium parts of end-of-life vehicles. This paper presents a novel magnetic roller model comprising circumferential and axial periodic arrangements of permanent magnets. A single permanent magnet was constructed as an equivalent current model, and the magnetic scalar potential equations were solved using simulation tools. This allowed the distribution of the magnetic field outside the magnetic roller to be studied. The results demonstrate that the novel permanent magnet array magnetic roller can enhance the magnetic field intensity and action distance of the external magnetic field, which is more conducive to the separation of large-scale broken copper and aluminium parts of scrap cars. The findings of this research provide a theoretical foundation for the separation of scrap car broken copper and aluminium parts.

This is a report on a dynamic autonomous magnetic interaction which does not depend on polarities resulting in short ranged repulsion involving one or more inertial bodies and a new class of bound state based on this interaction. Both effects are new to the literature, found so far. Experimental results are generalized and reported qualitatively. Working principles of these effects are provided within classical mechanics and found consistent with observations and simulations. The effects are based on the interaction of a rigid and finite inertial body (an object having mass and moment of inertia) endowed with a magnetic moment with a cyclic inhomogeneous magnetic field which does not require to have a local minimum. Such a body having some DoF involved in driven harmonic motion by this interaction can experience a net force in the direction of the weak field regardless of its position and orientation or can find stable equilibrium with the field itself autonomously. The former is called polarity free magnetic repulsion and the latter magnetic bound state. Experiments show that a bound state can be obtained between two free bodies having magnetic dipole moment. Various schemes of trapping bodies having magnetic moments by rotating fields are realized as well as rotating bodies trapped by a static dipole field in presence of gravity. Also, a special case of bound state called bipolar bound state between free dipole bodies is investigated.

In the present work, an innovative range of foams, based on flax gum-filled epoxy resin was developed, reinforced or not by flax fibers. Foams and composites with different gum and epoxy resin contents were produced and characterized for mechanical and thermal performances. To enhance the organic flax gum filler's cross-linking, we exploited the oxidized components' reactivity with the amine hardener (isophorone diamine). We compared the materials obtained with those derived from the native components. Flax gum and fibers were primarily characterized by chemical analysis, NMR, and FTIR to evaluate the mild oxidation of native materials. The formation of chemical bonds between oxidized polymer chains, epoxy resin, and hardener has been evidenced by FTIR, and the materials were then studied by SEM, X-ray computed micro-tomography (CT), and submitted to mechanical and thermal tests. The relevance of oxidation treatment was highlighted, through a significant increase in density and mechanical performances (+36% and +81%, respectively for the 100% flax gum material). The positive effect of flax fibers on homogeneity evidenced through micro-CT analysis was also clearly addressed. This set of promising results paves the way for future development of fully flax-based insulation composite materials.

Background: Fiber-reinforced composites (FRCs) have been proposed as an alternative to traditional metal alloys for the realization of frameworks in full-arch implant supported prostheses. The aim of the present in vitro study was to evaluate the deflection under load of seven prostheses endowed with frameworks made of different materials, including different types of fiber reinforced composites (FRCs). Methods: A master cast with four implant analogues in correspondence of the two lateral incisors and the two first molars was used to create full-arch fixed prostheses with the same shape and different materials. Prostheses were made in different materials (framework+veneering material): gold alloy+resin (Au+R), titanium+resin (Ti+R), FRC with multi-directional carbon fibers+resin (ICFRC+R), FRC with unidirectional carbon fibers+composite (UCFRC+C), FRC with glass fibers+resin (GFRC+R), FRC with glass fibers+composite (GFRC+C), resin (R, full-acrylic prosthesis). Flexural tests were conducted using Zwick/Roell Z 0.5 machine and the deflection of the lower surface of the prosthesis was measured in order to obtain load/deflection graphs. Results: Greater rigidity and less deflection were recorded for UCFRC+C, GFRC+C, followed by Ti+R, and Au+R. The greatest deformations were observed for resin alone, ICFRC+R and GFRC+R. The results were slightly different in the incisal region probably due to the greater amount of veneering material in this area. Conclusions: When used to realize full-arch frameworks, Au and Ti allow a predictable mechanical behavior with gradual deformations with increasing load. UCFRC also demonstrated good outcomes and less deflection than ICFRCs when loaded. The GFRC full-arch framework may be a valid alternative, however showed greater deflections. Further studies are needed in order to evaluated how different prosthesis design and material thickness might affect the outcomes.

To better understand the shape memory materials and self-healing materials, a new series of liquid-crystalline shape memory polyurethane (LC-SMPU) composites, named SMPU-OOBAm, were successfully prepared by incorporating 4-octyldecyloxybenzoic acid (OOBA) into the PEG-based SMPU. The effect of OOBA on the structure, morphology and properties has been carefully investigated. The results demonstrate that SMPU-OOBAm have liquid crystalline properties, triple-shape memory properties and self-healing properties. The incorporated OOBA promotes the crystallizability of both soft and hard segments of SMPU, and the crystallization rate of the hard segment of SMPU decreases when the OOBA-content increases. Additionally, the SMPU-OOBAm forms a two-phase separated structure (SMPU phase and OOBA phase), and it shows two-step modulus changes upon heating. Therefore, the SMPU-OOBAm shows triple-shape memory behavior, and the shape recovery ratio decreases with an increase in the OOBA content. Finally, SMPU-OOBAm shows self-healing properties. The new mechanism can be ascribed to the heating-induced “bleeding” of OOBA in the liquid crystalline state and the subsequent re-crystallization upon cooling. This successful combination of liquid crystalline properties, triple-shape memory properties and self-healing properties make the SMPU-OOBAm composites with many promise applications in smart optical devices, smart electronic devices and smart sensors.

This study reports rapid hydrolysis, acylation, and lipolysis with lipase B from Candida antarctica (CalB) and nanofructosome encapsulated CalB (CalB@NF) enzymes immobilized on silica-coated magnetic nanoparticles (Si-MNPs). Enzymatic hydrolysis was confirmed for conversion to p-nitrophenol (p-NP, λex=400 nm) from p-nitrophenyl butyrate (p-NPB, λex=270 nm), and various catalytic parameters such as Km, Vmax, and Kcat were calculated from Michaelis-Menten and Lineweaver-Burk plot. Efficiency of enzymatic hydrolysis was in the order of CalB > Si-MNPs@CalB > CalB@NF > Si-MNPs@CalB@NF, and reusability was much better with the enzyme immobilized on Si-MNPs than with the native enzyme. Enzymatic acylation was confirmed by the formation of benzyl benzoate (λex=229 nm) from benzoic anhydride (λex=240 nm), and efficiency exceeded 99% in all samples. Finally, enzymatic lipolysis was confirmed by the decomposition of olive oil to fatty acid such as oleic acid (λex=230 nm) using thin-layer chromatography (TLC), column chromatography, and proton nuclear magnetic resonance (1H -NMR). The lipases immobilized on Si-MNPs have the advantage of good thermal stability and reusability and are thus applicable to a wide range of industries.

Background: Multifunctional nanoparticles are known for their wide range of biomedical applications. Controlling the magnetic properties of these nanoparticles is imperative for various applications, including therapeutic angiogenesis. The study was performed to evaluate the magnetic properties and their control mechanisms by the external magnetic field. Methods: A 100nm magnetic nanoparticle was placed in the magnetic field, and parametrically the magnet field strength and distance was evaluated. Various models of magnetic strength and disposition were evaluated. Magnetic flux density, force/weight, and magnetic gradient strength were the parameters evaluated in electromagnetic computational software. Results: The seven-coil method with three centrally placed coils as Halbach array, and each coil with a flux density of 7 Tesla, and with a coil dimension of 20cmx20cm (square model) of each coil showed a good magnetic strength and force/weight parameters in a distance of 15cm from the centrally placed coil. The particles were then evaluated for their motion characteristics in saline. It showed good displacement and acceleration properties. After that, the particles were theoretically assessed in a similar mathematical model after parametrically correcting the drag force. After application of high drag forces, the particles showed adequate motion characteristics. When the particle size was reduced further, the motion characteristics were preserved even with high drag forces. Conclusion: There is potential for a novel method of controlling multifunctional magnetic nanoparticles using high magnetic fields. Further studies are required to evaluate the motion characteristics of these particles in-vivo and invitro.

It is of great academic significance to understand how the atomic structure of interfaces and boundaries in materials impacts the magnetic coupling nature across the boundaries and encourage development of state-of-the-art magnetic devices. Here, we carry out a systematic investigation of the atomic and electronic structures of twin boundaries (TBs) in LiFe5O8 thin films and determine their concurrent magnetic couplings using atomic-resolution transmission electron microscopy and atomistic first-principles calculations. The results show ferromagnetic or antiferromagnetic coupling can exist across the different TBs in LiFe5O8 (LFO) thin films and electrical structures within a few atomic layers directly rely on the TB atomic core structures. Uncovering one-to-one relationship between the magnetic properties of individual TB and the local atomic structures will clarify a thorough comprehension of numerous fascinating magnetic properties of commonly utilized magnetic materials, which will undoubtedly encourage the progress of sophisticated magnetic materials and devices.

The article presents the results of research work devoted to the study of composite materials on polymer binder with the content of modified mineral filler - water-dispersion paint and varnish materials on acrylic polymer with modified filler - diatomite. The aim of the study is to obtain polymer-based composites with modified diatomite (water-dispersion paint on acrylic binder) with improved performance properties. Methods: determination of porosity, adhesion, elasticity, hiding power of the control composition; determination of porosity, adhesion, elasticity, hiding power of the obtained composites with the use of modified filler; investigation of the influence of radiation in the infrared radiation (IR) region of the spectrum of the paint coating surface using FLIRB620 thermal imager. As a result of work it is noticed that modification of water dispersions by silica activated diatomite promotes elimination of the main disadvantages of materials and coatings on the basis of acrylate binder - low water resistance and low physical and mechanical characteristics, introduction of modified diatomite into water emulsion paint on acrylate basis does not lead to deterioration of the main operational characteristics of paint and varnish coatings - porosity, adhesion, elasticity and covering. When analyzing the effect of emissivity in the IR region of the spectrum of the paint coating surface, a significant effect of the quantitative content of modified diatomite on the reduction of emissivity of paint coatings in the IR region of the spectrum was established and it was shown that a significant effect of the reduction of emissivity of paint coatings in the IR region of the spectrum is provided by the introduction of modified diatomite in the amount of 40 wt.h. into the mixture. The influence of the time of full-scale tests in the investigated small range regardless of the quantitative composition of modified diatomite on the performance characteristics of the paintwork was established.

Pyrethroid pesticides (PYRs) as the third most widely used pesticides, following organophosphorus and carbamate pesticides, which are of significant importance in the analysis and detection of vegetables. However, the current pretreatment technology for PYRs confronts challenges of difficult separation and low enrichment efficiency, resulting in a cumbersome and time-consuming pretreatment process with poor selectivity. Here, a simple and efficient magnetic solid-phase extraction (MSPE) strategy was developed to simultaneously purify and enrich five PYRs in vegetables, with the magnetic covalent organic framework nanomaterial COF-SiO2@Fe3O4 as an adsorbent. The COF-SiO2@Fe3O4 was prepared by a simple solvothermal conditions method, using Fe3O4 as magnetic core, benzidine and 3,3,5,5-tetraaldehyde biphenyl as two building units. COF-SiO2@Fe3O4 could effectively capture the targeted PYRs by virtue of its abundant π-electron system and hydroxyl groups. The impact of various experimental parameters on extraction efficiency was investigated to optimize the MSPE conditions, including adsorbent amount, extraction time, elution solvent type and elution time. Subsequently, method validation was conducted under the optimal conditions in conjunction with gas chromatography-mass spectrometry (GC-MS). Within the range of 5.00–100 μg·kg-1 (1.00–100 μg·kg-1 for bifenthrin and 2.5–100 μg·kg-1 for fenpropathrin), the five PYRs exhibited a strong linear relationship, with determination coefficients ranging from 0.9990 to 0.9997. The limits of detection (LODs) were 0.3–1.5 μg·kg-1, and the limits of quantification (LOQs) were 0.9–4.5 μg·kg-1. The recoveries were 80.2–116.7% with relative standard deviations (RSDs) below 7.0%. Finally, COF-SiO2@Fe3O4, NH2-SiO2@Fe3O4 and Fe3O4 were compared as MSPE adsorbents for PYRs. The results indicated that COF-SiO2@Fe3O4 was an efficient and rapid selective adsorbent for PYRs. This method holds promising prospects for the determination of PYRs in real samples.

Biosensors are smart devices that convert biochemical responses to electrical signals. Designing biosensor devices with high sensitivity and selectivity is of great interest because of their wide range of functional operations. However, the major obstacles in the practical application of biosensors are their binding affinity toward biomolecules and the conversion and amplification of the interaction to various signals such as electrical, optical, gravimetric, and electrochemical signals. Additionally, enhancement of sensitivity, limit of detection, time of response, reproducibility, and stability are considerable challenges when designing an efficient biosensor. In this regard, hybrid composites have high sensitivity, selectivity, thermal stability, and tunable electrical conductivities. The integration of phthalocyanines (Pcs) with conductive materials such as carbon nanomaterials or metal nanoparticles (MNPs) improves the electrochemical response, signal amplification, and stability of biosensors. This review explores recent advancements in hybrid Pcs for biomolecule detection. Herein, we discuss the synthetic strategies, material properties, working mechanisms, and integration methods for designing electrochemical biosensors. Finally, the challenges and future directions of hybrid Pc composites for biosensor applications are discussed.

The state detection of power cable is very important to ensure the reliability of power supply. Traditional sensors are mostly based on electric field detection, the operation is complex, and its efficiency needs to be improved. This paper optimizes the design and development of the magnetic field detection sensor for AC power cables. Firstly, through the establishment of the magnetic field sensor model, it is determined that permalloy is the material of the magnetic core, the optimal aspect ratio of the magnetic core is 20, and the ratio of coil length to core length is 0.3. Secondly, the coil simulation model is established, and it is determined that the optimal number of turns of the coil is 11000 turns, the diameter of the enamelled copper wire is 0.08mm, and the equivalent magnetic field noise of the sensor is 0.06pT. Finally, the amplifying circuit based on negative magnetic flux feedback is designed and the sensor is assembled, and the experimental circuit is built for sensitivity test. the results show that the sensitivity of the magnetic field sensor is 327.6mV/μT. The sensor designed in this paper has the advantages of small size, high sensitivity, easy to carry and high reliability.

The spread of micro- (MPs) and nanoplastics (NPs) in the environment has become a significant environmental concern, necessitating effective removal strategies. In this comprehensive scientific review, we examine the use of magnetic nanoparticles (MNPs) as a promising technology for the removal of MPs and NPs from water. We first describe the issue of MPs and NPs and their impact on the environment and human health. Then the fundamental principles of using MNPs for the removal of these pollutants will be presented, emphasizing that MNPs enable selective binding and separation of MPs and NPs from water sources. Furthermore, we provide a short summary of various types of MNPs that have proven effective in the removal of MPs and NPs. These include ferromagnetic nanoparticles, MNPs coated with organic polymers, as well as nanocomposites and magnetic nanostructures. We also review their properties, such as magnetic saturation, size, shape, surface functionalization and stability, and their influence on removal efficiency. Next, we describe different methods of utilizing MNPs for the removal of MPs and NPs. We discuss their advantages, limitations, and potential for further development in detail. In the final part of the review, we provide an overview of existing studies and results demonstrating the effectiveness of using MNPs for the removal of MPs and NPs from water. We also address challenges that need to be overcome, such as nanoparticle optimization, process scalability, and the removal and recycling of nanoparticles after the completion of the process. This comprehensive scientific review offers an extensive insight into the use of MNPs for the removal of MPs and NPs from water. With improved understanding and the development of advanced materials and methods, this technology can play a crucial role in addressing the issue of MPs and NPs and preserving a clean and healthy environment.

Silicon carbide particle-reinforced aluminum matrix (SiCp/Al) composites are significant lightweight metal matrix composites extensively utilized in precision instruments and aerospace sectors. Nevertheless, the inclusion of rigid SiC particles exacerbates tool wear in mechanical machining, resulting in a decline in the quality of surface finish. This work undertakes a comprehensive investigation into the problem of tool wear in SiCp/Al composite materials throughout the machining process. Initially, a comprehensive investigation was conducted to analyze the effects of cutting velocity vc, feed per tooth fz, milling depth ap, and milling width ae on tool wear during high-speed milling under SCCO2-MQL (Supercritical Carbon Dioxide Minimum Quantity Lubrication) ultrasonic vibration conditions. Furthermore, a prediction model for tool wear was developed by employing the orthogonal test method and multiple linear regression. The model's relevance and accuracy were confirmed using F-tests and t-tests. Ultimately, through the utilization of a genetic algorithm, the milling parameters were optimized, resulting in the identification of the most optimal combination of parameters. Empirical findings suggest that the careful selection of milling parameters can significantly mitigate tool wear, extend the lifespan of the tool, and enhance the quality of the surface. This work serves as a significant point of reference for the processing of SiCp/Al composite materials.

The thermal degradation behaviour of 10:90 and 90:10 blends of Polyethylene Terephthalate (PET) and petroleum coke has been investigated using mechanical alloying (milling) at 300 rpm and for periods up to 1-10 hours. Milled specimens were characterised using SEM and x-ray diffraction; their thermal degradation behaviour was investigated using thermo-gravimetric analyser (TGA) for temperatures up to 1200°C. Whereas PET specimens showed a tendency towards flattening out and increased surface area during collisions in ball mills, petroleum coke particles tended to break down into smaller particles. 10:90 and 90:10 blends of PET and coke showed significant microstructural evolution with increasing speeds and time including fracture, strain hardening and re-welding. X-ray diffraction results showed clear evidence for increasing amorphous component in petroleum coke without much influence on PET crystallinity. Thermo-gravimetric results showed a significant increase in the overall degradation and much higher weight losses associated with mechanical alloying. This study has shown that mechanical alloying could be used to modify the degradation behaviour of coke/plastic blends and corresponding yield during pyrolysis with implications for plastic waste management.

In this study, the impact of the addition of high-aspect-ratio nano-ettringite to photocurable epoxy acrylate resin was explored, with a specific focus on the changes observed in viscosity, shrinkage, tensile strength, and elongation at the break of composites formed. Herein, the nano-ettringite samples were modified using KH-570. The 3 wt% or 6 wt% KH-570-modified and unmodified nano-ettringite were dispersed into the resin by ultrasonic treatment in conjunction with mechanical stirring. The grafting effects of nano-ettringite onto KH-570 were analyzed through scanning electron microscopy (SEM), X-ray diffraction (XRD), thermogravimetric (TG) analysis, and Fourier transform infrared spectroscopy (FTIR). The results demonstrate that increased dosages of unmodified and modified nano-ettringite led to increased viscosity of the composite while reducing shrinkage. At the same dosage, the photocurable resin with modified nano-ettringite demonstrated a lower shrinkage and a higher tensile strength. Notably, when the amount of modified nano-ettringite was 3 wt%, the highest tensile strength of the composite was 64.61 MPa, presenting a 72.57% increase compared to the blank sample. Furthermore, the incorporation of modified nano-ettringite as a filler provides a new perspective for improving the performance of photocurable epoxy acrylate resin composites.

Among earth’s microbial populations are the genes, functional capacities, generational memory and sentient cognition that enable microorganisms to adapt and thrive in the full range of ecological conditions found on planet earth. In prior sequential publications, we considered fundamental properties (e.g., use of and responses to sound, light, vibrations) and features of microorganisms that cause them to be critical co-partners of human and other holobionts as well as the potential benefits for humanity that can be gained by fully applying quantum-related and novel capacities of microbial life. In this narrative review we: 1) discuss key concepts concerning a microbially-enhanced and sustainable future, and 2) focus on electric- and magnetic- based features of microorganisms that make them pivotal for myriad benefits ranging from beyond pharma-based health and wellness to free- and/or renewable energy and restorative agriculture to improved human networking. While the benefits are many, the risks posed by hazardous electric or magnetic field exposures to both holobionts and microbial communities are significant. This review concludes that microbes and their remarkable capacities offer both humanity and the planet a much brighter future if we reverse the demonization of microbes and wanton microbiome degradation that has predominated much of the past century.

Concrete contributes 8% of all global carbon emissions making the need to find substitute critical for environmental sustainability. Research has indicated the potential for recycled plastics to be used as concrete substitutes. This study extends existing research by investigating the use of polycarbonate (PC) in plastic sand bricks as a mechanical equivalent to concrete. PC has high compressive strength, durability, impact strength, thermal resistivity, clarity, fatigue resistance, and UV resistance. This work provides a method and mold to produce a matrix of sand-plastic sample compositions with dimensions adhering to ASTM D695 standard for compressive properties of rigid-plastic. Compositions of 0% (control), 20%, 30%, 40%, and 50% sand by weight were tested. Samples were tested for compressive strength until yield and stress-strain behaviors plotted. The results for 100% PC demonstrated an average and maximum compressive strength of 71 MPa and 72 MPa, respectively. The 50% PC and 50% sand composition yielded an average and maximum compressive strength of 71 MPa and 73 MPa respectively with an increase in compressive stiffness, and transition to shear failure resembling cement. With a composite density of 1.86 g/cm3 against concrete’s average 2.4 g/cm3, and a compressive strength exceeding commercial concrete demands of 23.3 MPa to 30.2 MPa, this lightweight alternative meets the strength demands of concrete, reduces the need for new construction materials, and provides an additional recycling opportunity for nonbiodegradable waste plastic.

This investigation mainly focused on the microstructural analysis of Al based hybrid metal matrix composites. Aluminium as base metal and reinforced with 2% B4 C, ZrO2 (2%,4%,6%), SiC (4%,8%,12%). Specimens were manufactured by using conventional stir casting technique. Hybrid metal matrix composites were examined by using Scanning electron microscope. This research explained XRD, EDS and Fractography analysis. This investigation shows the reinforced material has given better results in all aspects than pure Al6061 alloy and homogeneous dispersion of particles inside the matrix. Porosity, delamination, cracks, particle distributions were observed through microstructural analysis. Additionally determined the crystal size of pure Aluminium 6061 alloy and hybrid composites.

Integrating nanomaterials like carbon nanotubes (CNTs) and iron oxide (Fe₃O₄) into epoxy composites has significant interest due to their potential to enhance mechanical properties. This study evaluates the impact of dispersion quality on the mechanical performance of CNT/Fe₃O₄/Epoxy composites, comparing stirring and sonication methods at three different loadings: 0.1, 0.3, and 0.5 wt.%. Tensile testing revealed that sonicated composites consistently outperformed stirred composites, with a significant increase in elastic modulus and ultimate tensile strength (UTS). However, fracture strain decreased in both composite types compared to pure epoxy, with sonicated composites experiencing a more significant reduction than stirred composites. These results underscore the importance of high-quality dispersion for optimizing mechanical properties.

(1) Background: The aim of this investigation is to determine the effect of archwires’ deflection on the temperature transitions driving the austenite to martensite transformation (and vice versa) and the force released by NiTi and CuNiTi orthodontic wires. (2) Methods: Round cross-section archwires have been investigated. The calorimetric approach has been used for measuring transition temperatures occurring in the unstressed (e.g. undeflected) state of the wires. Static Thermo-mechanical analysis in a temperature controlled wet environment has been performed in the range of temperature between 5°C and 55°C for measuring temperature transitions occurring in highly deflected archwires in conjunction with the force released by these wires. (3) Results: Plateau forces investigated in Part I and those reported in the literature describes the wire’s behaviour only at deflection levels close to the end point of the force plateau extension detected at 37°C. Upon heating or cooling, the austenite finish (Af) transition temperature and the martensite start (Ms) temperature largely depends on the deflection level for both NiTi and CuNiTi. (4) Conclusions: The plateau force levels at 37°C, broadly reported in the literature, only represent the lower boundary force that a superelastic wire releases at 37°C above its elastic limit. For both NiTi and CuNiTi, plateau force levels at 37°C can be predicted by the static TMA profile matching the end point of the force plateau extension. Transition temperatures in largely deflected wires are significantly higher than those determined through the calorimetric approach.

(1) Background: The aim of the research was to present and emphasize the importance of magnetic resonance imaging (MRI) in diagnosing Achilles tendon (AT) ruptures by presenting case reports. (2) Materials and Methods: The sample of respondents included 7 patients (4 males and 3 females, 2 athletes and 5 non-athletes), aged 25 to 58 years, with AT injuries, who were examined and treated at the Institute for Treatment and Rehabilitation "Niška Banja", Niš, Serbia. Ankle examinations with MRI were conducted using the Esaote O-scan 0.3 T machine. The examinations were performed without the application of a paramagnetic contrast agent and without the use of anesthesia. Results: The MRI method's sensitivity and overall diagnostic accuracy were excellent, with 100% true positives. In our study, the method accurately detected the presence, location, and severity of AT injuries in all cases. MRI is an important and reliable method for detecting AT injuries, classifying them, monitoring the course of recovery, and assessing the effects of therapy. Conclusions: An unrecognized or delayed diagnosis of an AT injury can lead to chronic changes. Timely diagnosis (clinical examination, ultrasonography, magnetic resonance imaging) and appropriate treatment (conservative or operative) enable patients to return to normal activities, including sports. Unfortunately, the use of MRI is limited by restricted access and the cost of the examination.

Titanium-based metal-matrix composites manufactured by additive manufacturing offer tremendous lightweighting opportunities. However, processing high reinforcement content remains challenging. This study reports an improved manufacturing process for Ti-TiC enabling high reinforcement content and significant fracture strain concurrently: mechanical blending, followed by laser powder bed fusion and a single heat treatment. As-built microstructure shows both un-melted TiC particles and sub-stoichiometric TiC dendrites resulting from a partial dissolution of TiC particles. The heat treatment is shown to fully convert TiC dendrites into equiaxed TiC grains. Reduction of the C/Ti ratio in TiC during the process results in an increase in the reinforcement content, from a nominal 12 vol% to an effective 21.5 vol%. Ti-TiC tensile samples reached fracture strains of up to 1.7%, Young’s moduli of up to 149 GPa and ultimate tensile strengths of up to 827 MPa. Lower TiC initial powder size distributions displayed the best mechanical performance.

There is currently no unified explanation for the origin of Earth's magnetic field, planetary magnetic fields, stellar magnetic fields, and neutron star magnetic fields, and most importantly, none of these theories have been experimentally verified. This paper is based on a new unified theory of mechanics and its derived applications, which may provide a better explanation for the origin of magnetic fields in celestial bodies and can be experimentally tested to better answer the observed phenomena: (1) the greater the mass of the celestial body, the stronger the magnetic field; (2) the faster the rotation speed of the celestial body, the stronger the magnetic field; (3) the higher the density of the celestial body, the stronger the magnetic field produced.

The goal of this work was to develop the acrylonitrile-butadiene (NBR) elastomer composites filled with hydroxyapatite (HAP), which were characterized with improved cure characteristics and burning resistance. Silane, i.e., (3-aminopropyl)-triethoxysilane, ionic liquid, i.e., 1-decyl-3-methylimidazolium bromide and surfactant, i.e., cetyltrimethylammonium bromide, were used to improve the filler’s dispersibility in the elastomer matrix and to reduce the time and temperature of vulcanization. The effect of HAP and dispersants on the cure characteristics, crosslink density and physico-chemical properties of NBR composites was explored. The additives used, especially the ionic liquid and surfactant, effectively improved the dispersion of HAP in NBR matrix. The amount of HAP and the dispersant used strongly affected the cure characteristics and crosslink density of NBR. The optimal vulcanization time significantly increased with HAP content and was pronouncedly reduced when ionic liquid and surfactant were applied. In addition, ionic liquid and surfactant significantly lowered the onset vulcanization temperature, improved the crosslink density and hardness of the vulcanizates, while impairing their elasticity. HAP and dispersants did not significantly affect the damping properties and chemical resistance of NBR vulcanizates. Above all, application of HAP considerably enhanced the resistance of vulcanizates to thermo-oxidative aging and reduced their flammability compared to the unfilled NBR.

This work focuses on the theoretical study of the effect of entanglement in the Yttrium Barium Copper Oxide (YBCO) superconductor on the critical current density, critical magnetic field, and penetration depth. Using the Ginzburg Landau (GL) theory, the expression for the GL coherence length, the critical current density, the lower critical magnetic field (Hc1), and the upper critical magnetic field (Hc2) for the entangled superconducting YBCO was obtained. At zero external magnetic fields, YBCO was found to undergo a transition from the normal state to the superconducting state at 93K and returned to normal. We found a direct relationship between the GL coherence length penetration depth and the temperature of the entangled superconducting YBCO. The graphs of the lower critical magnetic field (Hc1) and critical current density against temperature show a non-linear dependence.In contrast, the graph of the upper critical magnetic field (Hc2) against temperature (T) shows the linear dependence, which is in agreement with existing theoretical observations. On the other hand, the graph of critical current density against the distance of separation between the entangled electrons that form a cooper pair showed that the critical current density increases between 1.8 and 6 nanometers attaining a constant value after reaching 7 nanometers for infinite distances. Finally, for lower critical fields, the magnetic field decreases between 1.5 to 6 nanometers attaining a constant value of the magnetic field, for infinite values of distance of separation between the entangled pair of electrons.

Pore structure characterization and fractal analysis have great significance for understanding and evaluating tight limestone reservoirs. In this work, the pore structure of tight limestone is characterized combined with low-temperature nitrogen adsorption (LTNA) and low-field nuclear magnetic resonance (NMR), and the fractal dimension of tight limestone pore structure is discussed based on LTNA and NMR data. The results indicate that the pores of tight limestone have H3 and H4 types, the pore size distribution (PSD) of H3 type is a wave distribution ranging from 2 to 10 nm, and the PSD of H4 type is a unimodal distribution ranging from 2 to 10 nm. The transverse relaxation time (T2) spectrum of tight limestone shows single peak (DF), double peak (SF) and three peak (TF), and the T2 spectrums for micropores, mesopores and macropores range from 0.1 to 10 ms, from 10 to 100 ms, and greater than 100 ms, respectively. The LTNA fractal dimension of tight limestone (DL) ranges between 2.4446 and 2.7688, with an average of 2.5729, and the NMR fractal dimensions of micropores (DNMR1), mesopores (DNMR2) and macropores (DNMR3) are distributed between 0.3744 to 1.1293, 2.4263 to 2.9395 and 2.6582 to 2.9989, respectively. Moreover, there is no correlation between fractal dimension and permeability and porosity, a negative correlation between DL and average pore radius, a positive correlation between DL and specific surface area, and a positive correlation between DNMR2 and DNMR3 and micropore content, while DNMR2 and DNMR3 are negatively correlated with the content of mesopores and macropores.

This study presents, for the first time, the development of fibers with favorable properties for biodegradable wound dressings made from the Ecovio® (EC) polymer blend, composed of poly(lactic acid) (PLA) and poly(butylene adipate-co-terephthalate) (PBAT), incorporated with tea tree essential oil (TTE). TTE presented antimicrobial activity against Pseudomonas aeruginosa and Staphylococcus aureus, achieving minimal inhibitory concentrations of 15 and 7.5 mg/mL, respectively. The TTE was mixed with EC in a binary chloroform and formic acid (85/15 v/v) mixture, leading to homogeneous and wettable fibers by electrospinning. The EC/TTE fibers were characterized confirming the TTE in the fibers. The tests showed that TTE (0.5, 1.0 or 1.5 mL) improved the polymer blend electrospinnability. TTE (1.5 mL or 75 w% concerning the EC) lead to homogeneous fibers with an average diameter of 278 nm. TTE (75 w%) increased the wettability of the EC fibers from 120±2° to 69±1°. Preliminary bacterial adhesion and proliferation assays demonstrated that the EC/TTE fibers have anti-adhesive activity e seems to be more toxic against P. aeruginosa compared to S. aureus after 24 hours of incubation. Compatibility tests with human blood indicated that the EC/TTE fibers accelerate blood coagulation. The EC/TTE fibers exhibit promising chemical and biological properties (in vitro) for the development of wound dressings.

This review summarizes the most recent developments of research on protozoan parasite infections ac-quired through food and drinking water and is aimed at gathering updated knowledge on the risk factors, illnesses caused, and measures for prevention. Reports included dated from 2019 to the present and regarded recent outbreaks and cases of severe infec-tions, prevalence in different population segments and food handlers, and occurrence in food and drinking water. Cryptosporidium spp., Entamoeba histolytica, Giardia intestinalis, Trypanosoma cruzi and Toxoplasma gondii were the microorganisms most frequently involved in large outbreaks and/or severe infections, while Cyclospora cayetanensis was most frequently involved in single case reports. Cystoisospora belli was implied in severe infections in immunocompromised patients, while Blastocystis homi-nis, Sarcocystis spp., Dientamoeba fragilis, Endolimax nana and Pentatrichomonas hominis appeared to be less relevant for number of symptomatic infections and pathogenic potential. A progressive improvement in surveillance of protozoan infections and infection sources was highlighted, especially in developed countries. The apparent increase in cases was concomitant with the implementa-tion of reporting systems and the application of molecular diagnostic methods that represent valuable in-struments for establishing epidemiological links and preventing or limiting outbreaks. The pathogenic role and sources of infection should be better elucidated for some species.

Although the potential of natural minerals for purification of liquid radioactive wastes (LRW) from radionuclides has been widely studied, the use of hybrid polymer composites made of zeolite is still rather scarce. This article reports on the preparation of zeolite based hybride polymer composites using the in-situ polymerization technique in the body of mineral matrix and its intercalated with copper ferrocyanide (CuFC) forms. This hybrid polymer composites have shown unique and enhanced properties as compared to the individual mineral. The change in conventional properties of two mixed minerals such as zeolite and bentonite and their intercalated with CuFC forms were probed using technics such as scanning electron microscopy (SEM), X-ray diffraction (XRD), Mossbauer spectroscopy (MS) and FT-IR analysis. The totality of analysis showed a coexistence of intercalated and percolated zeolite phases. The hybrid polymer composites exhibited both adsorption and ion-exchangr properties in removal of radionuclides from LRW.

.With the increasing use of carbon fiber reinforced plastics in various area, carbon fiber composites based on prepregs have attracted attention in industries and academia research. However, prepreg manufacturing processes are costly, and the strength of structures varies depending on the orientation and defects (pores and delamination). For non-contact evaluation of internal defects, we proposed lock-in infrared thermography to investigate orientation angles after a compression test. We also conducted a drop-weight impact test to study the behaviour of the composites after impact according the fibers orientation for composite fabricated using unidirectional carbon fiber prepregs. Using CAI tests, we determined the residual compressive strength and confirmed the damage modes using a thermal camera. The results of the drop weight impact tests show that the specimen laminated at 0° suffered the largest damage because of susceptibility of the resin to impact. In contrast, the specimens oriented in of 0°/90° and +45°/–45° directions transferred more than 90% of the impact energy back to the impactor because of the lamination of fibers in the orthogonal directions. Furthermore, the specimens that underwent complete damage in the impact tests were subjected to the lock-in method and showed internal delamination and cut fibers. With the finite elements analysis, the damage of each ply could be observed. Moreover, the temperature differences in the residual compression tests were not significant.

In the former mining district of La Carolina (southern Spain), waste materials were accumulated without first waterproofing the substrate. Additionally, these mining dams were abandoned without any type of restoration, conditions that present a significant risk of contaminating the surrounding soils and waters. Prior to carry out the necessary works for isolating these residues, morphological characterization of the contact with the base substrate is needed. For that purpose, in recent years, different indirect study techniques have been used, among which electrical to-mography stands out. In this work, a less common geophysical technique, magnetometry, both in its magnetic and gra-diometric modalities, is used as an alternative method to analyse the geometry and structure of a mining dam. The results obtained with this methodology are compared with the results provided by electrical techniques, as well as with direct data from mechanical surveys and aerial photo-graphs prior to waste deposition. The magnetic anomaly curves obtained with geometric models generated with the Mag2dc program were also analysed. This comparative study shows the use-fulness of magnetic prospecting in characterizing the base geometry of these mining structures and therefore the interest in its application to environmental characterization studies.

The presented work offers a novel process scheme for valorizing historical Pb-Zn slag, which involves crushing, grinding, and then using separation techniques to concentrate valuable components (nonferrous metals). This methodology could have a significant impact on the global beneficiation of metallurgical slags since, in theory, it is significantly more simple, environmentally friendly, and cost-effective than standard pyrometallurgical or hydrometallurgical procedures. According to previous physicochemical and mineralogical studies, Pb-Zn slag from "Topilnica" Veles is a valuable secondary raw material. This inhomogeneous technogenic resource contains substantial amounts of nonferrous metals (Pb, Zn, Cu, and Ag). However, laboratory tests have indicated that the Pb-Zn slag contains a very uneven valuable metals amounts, ranging from several g/ton to several tens of g/ton. The main issue is that traditional metallurgical procedures for releasing beneficial elements are not commercially viable since the valuable elements are "trapped" within amorphous aluminosilicates or intergrowths of alloy grains and glassy phases. Gravity concentration (Wilfley 13 shaking table) and magnetic separation (Davis separator and disk separator) were used to obtain the final concentrate following comminution and grindability testing. The gravity concentration proved more effective. This streamlined approach of valorizing Pb-Zn slag can reduce the need for hazardous chemicals used in hydrometallurgical refinement operations, as well as the extremely high temperatures required for pyrometallurgical processing. This is the first investigation into the feasibility of this novel approach, which includes direct investigations of the Pb-Zn slag feed using these alternative technologies. After extracting the valuable metals, the amorphous aluminosilicate part of the Pb-Zn slag can be reapplied as an alternative raw material in the building sector, adding to the circularity of the suggested approach..

The influence of post-processing conditions on the magnetic properties of amorphous and nanocrystalline microwires have been thoroughly analyzed, paying attention on the influence of magnetoelastic, induced and magnetocrystalline anisotropies on the hysteresis loops of Fe-, Ni- and Co-rich microwires. We showed that magnetic properties of glass-coated microwires can be tuned by the selection of appropriate chemical composition and geometry in as-prepared state or further considerably modified by appropriate post-processing, which consists of either annealing or glass-coated removal. Furthermore, stress-annealing or Joule heating can further effectively modify the magnetic properties of amorphous magnetic microwires owing to induced magnetic anisotropy. Devitrification of microwires can be useful for either magnetic softening or magnetic hardening of the microwires. Depending on the chemical composition of the metallic nucleus and on structural features (grain size, precipitating phases) nanocrystalline microwires can exhibit either soft magnetic properties or semi-hard magnetic properties. We demonstrated that the microwires with coercivities from 1 A/m to 40 kA/m can be prepared.

Achieving the thermal conductivity required for efficient heat management in semiconductors and other devices requires the integration of thermally conductive ceramic fillers at concentrations of 60 vol% or higher. However, the increased filler content often negatively affects the mechanical properties of the composite matrix, limiting its practical applicability. To address this issue, in this paper, we present a new strategy to reduce the required ceramic filler content: the use of a thermally conductive ceramic composite filler with carbon nanotubes (CNT) grown on aluminum nitride (AlN). We have combined catalyst coating technology with vacuum filtration to ensure that the catalyst is uniformly applied to micrometer-sized AlN particles, followed by efficient and uniform synthesis of CNTs using a water-assisted process in a vertical furnace. By carefully controlling the number of vacuum filtration cycles and the growth time of the CNTs, we demonstrate precise control over the number and length of the CNT layers, thereby adjusting the properties of the composite to the intended specifications. When AlN/CNT hybrid fillers are incorporated into silicone rubber, while maintaining the mechanical properties of rubber, the thermal diffusivity achieved at reduced filler levels exceeds that of composites using AlN-only or simultaneous AlN and CNTs formulations. This demonstrates the critical role of CNTs on AlN surfaces. Our study represents a significant advancement in the design of thermally conductive materials with potential implications for a wide range of applications.

Epoxy powders offer a low-cost means of manufacturing thick section composite parts, such as those found in wind and tidal turbines. Currently, their processing cycle includes a lengthy drying stage (≥ 15 h) to remove ambient moisture. This prevents void defect formation and, thereby, a reduction in mechanical properties, however, it constitutes up to 60% of the processing time. Little research has been published on the study of this process or its optimisation. Experimental and simulated analyses are used to investigate the effects of hygroscopicity in epoxy powder composites. In particular, focus is given to the drying process, which is used to prevent void defect formation and, thereby, a reduction in mechanical properties. As such, tests are performed to quantify the void content of dried and undried laminates, and to measure its impact on transverse flexural strength. Dynamic vapour sorption analysis is used to study the sorption behaviour of the epoxy powder. Sorption data is fitted to a modified linear driving force model, and then implemented in existing process simulations tools. The drying of a thick epoxy powder composite section is simulated to investigate the influence of powder sintering on the duration required for drying. It is shown that the epoxy powder is slightly hygroscopic (1.36 wt%) and exhibits sorption behaviour that is characteristic of glassy polymers. This results in up to 4.8% voids (by volume) if processed in an undried state, leading to a 43% reduction in transverse flexural strength. Process simulations reveal that a standard drying cycle prematurely sinters the powder; inhibiting moisture release. By maintaining a powder state, simulations show that the drying cycle can be reduced to 5 h.

The present decade has witnessed numerous investigations focussed on the determination of the mechanical properties of Fly ash composites. These composites have attracted attention, especially in the form of reinforcements owing to their excellent tensile and compressive properties coupled with impact and hardness response. A number of techniques viz. in-situ deposition, hand-up lay and compo-casting techniques have been reported to fabricate these composites. However, in the context of these composites, a systematic structure-property correlation has not been established till date. The present review is aimed at highlighting the current state of research in the avenue of Fly ash composites from two different viewpoints, viz. (i) fabrication technique and (ii) mechanical properties of the fabricated composites. Moreover, the necessity of establishing systematic structure-property correlation in these materials has also been briefly discussed from the author’s viewpoint.

In the study of relativistic jets one of the key open questions is their interaction with the environment on the microscopic level. Here, we study the initial evolution of both electron–proton (e^- - p⁺) and electron–positron (e^±) relativistic jets containing helical magnetic fields, focusing on their interaction with an ambient plasma. We have performed simulations of "global" jets containing helical magnetic fields in order to examine how helical magnetic fields affect kinetic instabilities such as the Weibel instability, the kinetic Kelvin-Helmholtz instability (kKHI) and the Mushroom instability (MI). In our initial simulation study these kinetic instabilities are suppressed and new types of instabilities can grow. In the e^- - p⁺ jet simulation recollimation-like instability occurs and jet electrons are strongly perturbed. In the e^± jet simulation a recollimation-like instability occurs at early times followed by a kinetic instability and the general structure is similar to a simulation without helical magnetic field. Simulations using much larger systems are required in order to thoroughly follow the evolution of global jets containing helical magnetic fields.

A single water pollution by dyes is a huge environmental problem; there is a necessity to produce new decolorization methods that are effective, cost-attractive, and suitable in industrial use. Magnetic chitosan polymers offer the advantage of easy separation from the dye solution. In this work, a Chitosan-Fe polymer was synthesized, characterized, and tested for removal of the azo dye Direct Red 83:1 from water. The polymer was characterized in terms of surface morphology (SEM), elemental analysis (EA), differential scanning calorimetry (DSC), thermal gravimetric analysis (TGA), infrared spectrophotometry (IR), X-ray powder diffraction (XRD) and density functional theory (DFT). The reported results hint that 1 g and pH 7.0 were the best conditions to carry out both kinetic and isotherm models. To understand the adsorption behavior of Direct Red 83:1 onto the polymers, adsorption rate and maximum adsorption capacity were calculated using kinetic tests and isotherm curves respectively. The kinetic data and mechanism of the adsorption process were analyzed by three models and the equilibrium data by three adsorption isotherms. The results indicated that the adsorption process follows a pseudo-second-order kinetics (R2= 0.999) and fits the Temkin isotherm (R2= 0.946), indicating that the adsorption occurred on heterogeneous surfaces. The newly synthesized Chitosan-Fe polymer exhibited good adsorption properties and easy separation of cleaned water.

Based upon Maxwell's equations, it has long been established that oscillating electromagnetic (EM) fields incident upon a metal surface decay exponentially inside the conductor, leading to a virtual EM vacuum at sufficient depths. Magnetic resonance imaging (MRI) utilizes radiofrequency (r.f.) EM fields to produce images. Here we present the first visualization of a virtual EM vacuum inside a bulk metal strip by MRI, amongst several novel findings. We uncover unexpected MRI intensity patterns arising from two orthogonal pairs of faces of a metal strip, and derive formulae for their intensity ratios, revealing differing effective elemental volumes (voxels) underneath these faces. Further, we furnish chemical shift imaging (CSI) results that discriminate different faces (surfaces) of a metal block according to their distinct nuclear magnetic resonance (NMR) chemical shifts, which holds much promise for monitoring surface chemical reactions noninvasively. Bulk metals are ubiquitous, and MRI is a premier noninvasive diagnostic tool. Combining the two, the emerging field of bulk metal MRI can be expected to grow in importance. The fundamental nature of results presented here may impact bulk metal MRI and CSI across many fields.

This review is focused on current state-of-the-art research on electroactive-based materials and their synthesis, as well as their physicochemical and biological properties. Special attention is paid to pristine intrinsically conducting polymers (ICPs) and their composites with other organic and inorganic components, well-defined micro- and nanostructures, and enhanced surface areas compared with those of conventionally prepared ICPs. Hydrogels, due to their defined porous structures and being filled with aqueous solution, offer the ability to increase the amount of immobilized chemical, biological or biochemical molecules. When other components are incorporated into ICPs, the materials form composites; in this particular case, they form conductive composites. The design and synthesis of conductive composites result in the inheritance of the advantages of each component and offer new features because of the synergistic effects between the components. The resulting structures of ICPs, conducting polymer hydrogels and their composites, as well as the unusual physicochemical properties, biocompatibility and multi-functionality of these materials, facilitate their bioapplications. The synergistic effects between constituents have made these materials particularly attractive as sensing elements for biological agents, and they also enable the immobilization of bioreceptors such as enzymes, antigen–antibodies, and nucleic acids onto their surfaces for the detection of an array of biological agents. Currently, these materials have unlimited applicability in biomedicine. In this review, we have limited discussion to three areas in which it seems that the use of ICPs and materials, including their different forms, are particularly interesting, namely, biosensors, delivery of drugs and tissue engineering.

The bipartite entanglement is comprehensively investigated in the mononuclear molecular complex (Et3NH)[Ni(hfac)2L], where HL denotes 2-(2-hydroxy-3-methoxy-5-nitrophenyl)-4,4,5,5-tetramethyl-4,5-dihydro-1H-imidazol-3-oxide-1-oxyl and hfacH stands for hexafluoroacetylacetone. From the magnetic point of view, the molecular compound (Et3NH)[Ni(hfac)2L] consists of an exchange-coupled spin-1 Ni2+ magnetic ion and a spin-12 nitronyl-nitroxide radical substituted nitrophenol. The nickel-radical molecular complex affords an experimental realization of a mixed spin-(12, 1) Heisenberg dimer with a strong antiferromagnetic exchange coupling J/kB= 505 K and two distinct g-factors gRad=2.005 and gNi=2.275. By adopting this set of magnetic parameters we demonstrate that the Zeeman splitting of a quantum ferrimagnetic ground-state doublet due to a weak magnetic field may substantially reinforce the strength of bipartite entanglement at low temperatures. The molecular compound (Et3NH)[Ni(hfac)2L] maintains sufficiently strong thermal entanglement even at room temperature, vanishing only above 546 K. Specifically, the thermal entanglement in the nickel-radical molecular complex retains approximately 40% of the maximum value corresponding to perfectly entangled Bell states at room temperature, which implies that this magnetic compound provides suitable platform of a molecular qubit with potential implications for room-temperature quantum computation and quantum information processing.

PVC/CNT membranes were electrospun, and subsequently characterized by thermal analyses (TGA and DSC), transmission and scanning electron microscopies (TEM and FEG) and electrical impedance spectroscopy (EIS). TEM images show that most of the nanotubes were encapsulated, inside the fibers and oriented along them. FEG showed no significant differences in the average diameters. The CNTs caused a significant reduction (up to 20 °C) in the glass transition temperature (Tg) in relation to the resin and a positive impact on thermal stability. Nyquist plots is possible to observe a charge transfer resistance of 38 and 40 Mohm, respectively, for pure PVC and PVC/CNT 3%. It is suggested the high porosity and encapsulation of CNTs in the fibers prevents the formation of a percolation network. The present study aims to evaluate the effect of the encapsulation of CNTs in morphology, thermal and impedance spectra of electrospun composites.

To obtain a cost-effective and high-performance composite material of polybutylene adipate-terephthalate (PBAT), for this study we selected microcrystalline cellulose, which is inexpensive and easily available, as the reinforcing medium. Hexadecyl trimethoxysilane (HDTMS) containing a long carbon chain was chosen to silanize the microcrystalline cellulose (MCC) to obtain silanized cellulose (SG). Three types of SGs with different degrees of silanization were obtained by controlling the reaction ratio. Characterization of these three types of SGs was conducted using FTIR, TEM, and water absorption analysis. Subsequently, PBAT/SG composites were prepared through a sol-gel method, and the effects of these three types of SGs on the thermal stability, compatibility, mechanical properties, and dynamic thermomechanical properties of PBAT were evaluated. Furthermore, the mechanism behind enhancing the mechanical properties of the composite was analyzed. The results demonstrated successful synthesis of SG. As the reaction ratio between HDTMS and MCC increased, the nanoparticle size increased, while the water absorption decreased significantly. After SG was added to the PBAT composites, the yield stress increased while maintaining good thermal stability. Both the SEM and DMA results indicated good compatibility of the PBAT/SG composites. Analysis of the mechanical properties revealed that the tensile strength initially increased and then decreased with increasing blending ratio for all three composites tested; among them, the PBAT/SG2 composites exhibit superior performance, with a maximum tensile strength reaching 22 MPa at an 85/15 blending ratio—nearly 30% higher than that of pure PBAT alone. The addition of SG significantly improved the strength of the PBAT, and we speculated as to the underlying mechanism involved. This study provides a new idea for the industrial-scale development of degradable polyesters with low cost and good mechanical properties.

With the development of nuclear technology application, radiation safety has been widely concerned, and there is an urgent need for novel shielding materials. Among the various options available, non-lead organic composite shielding material has emerged as a promising solution in the field of radiation shielding due to its high strength, easy processing, and light weight. In this study, tungsten/epoxy resin (W/EP) composite samples with tungsten weight fraction from 0% to 60% were prepared. The shielding and mechanical properties of W/EP composites were investigated. The results show that the results showed that the higher the tungsten content, the greater the shielding capacity of W/EP composites, particularly for low-energy gamma ray (γ) shielding. However, the addition of tungsten reduces the impact strength and tensile properties of the material. Overall, for 300 keV γ-ray, W/EP with 30% tungsten content has comparable shielding capacity to ordinary concrete. W/EP composite materials can serve as shielding materials for low-energy γ-rays.

Poly-ether-ether ketone (PEEK) is a great potential thermoplastic in industry and medical treatment and health. In this work, the PEEK/GO and PEEK/MoS2 composites were prepared by a novel hot isostatic pressing method. The addition of GO alters the tribological behaviours mechanism, fatigue wear mechanism is predominant to PEEK/GO composites. However, the combination of abrasive and adhesive wear mechanisms is observed for PEEK/MoS2 composites and PEEK. The reason is the hardness and tensile strength of composites are increased with the appropriate addition of GO. The response time to stable friction state of PEEK/GO and PEEK/MoS2 composites reduces in compared with PEEK, which conduce to shorten running-in time, reduce energy consumption and improve the tribological performances of composites. The addition of GO and MoS2 can effectively decrease the friction coefficient and wear rate, and the optimal content of GO and MoS2 was 0.7 wt.% and 15 wt.%, respectively. The results indicate that PEEK/GO and PEEK/MoS2 are impressive composites that possess super tribological properties.

In view of the problem that the output thrust of solenoid actuator is affected by various factors and is difficult to calculate in actual working conditions, this paper proposes a semi-analytical model constructed by magnetic field subdomain method with internal and external boundary conditions in cylindrical coordinate system for calculation, and the general solution equations of magnetic vector potential for each subdomain are derived and solved by MATLAB. Taking a push-pull electromagnet as an example, the finite element simulation and experimental comparative analysis are carried out. The correctness and applicable conditions of the subdomain method are illustrated by comparing the gradient plot of magnetic vector potential, inductance curve and electromagnetic force. By calculating the output thrust after considering the core gravity, spring force and electromagnetic force, it is shown that this method has the advantage of computational flexibility compared with the finite element method, and it is easier to write special algorithms according to various working conditions to calculate the important parameters in engineering applications.

Lacunary polyoxometalates (POMs) are negatively charged metal−oxo clusters, formally obtained from plenary topologies via fragment removal. Owing to the fragment removal, the lacunary POMs archetypes are rich in nucleophilic terminal oxo ligands, making them suitable for post-synthetic coordination with various heterometals. Trilacunary heteropolytungstates (het-ero-POTs) based on bowl-shaped {W9O30} framework incorporating a central lone-pair containing {XO3} hetergroup (X = AsIII, SbIII, and BiIII) function as all-inorganic scaffolds that in the presence of d-block metal cations typically construct sandwich-like dimers of Hervé and/or Krebs. Herein we review the preparative approaches, compositional and magnetic versatility of the constructing Hervé and Krebs type dimers and discuss prospective use as POMtronics.

Faraday's Law of induction is often stated as "a change in magnetic flux causes an EMF"; or, more cautiously, "a change in magnetic flux is associated with an EMF"; It is as well that the more cautious form exists, because the first "causes" form can be shown to be incompatible with the usual expression for EMF. This is not, however, to deny the causality as reasonably inferred from experimental observation ­ it is the equation for Faraday's Law of induction which does not represent the claimed cause-and-effect relationship. Here we investigate a selection of different approaches, trying to see how an explicitly causal mathematical equation, which attempts to encapsulate the "a change in magnetic flux causes ..." idea, might arise.

Highly-doped graphene samples show the conductance reduced and the shot-noise power enhanced compared to standard ballistic systems in two-dimensional electron gas. These features can be understood within a model assuming incoherent scattering of Dirac electrons between two interfaces separating the sample and the leads. Here we find, by adopting the above-mentioned model for the edge-free (Corbino) geometry and by means of the computer simulation of quantum transport, that another graphene-specific feature should be observable when the current flow through a doped disk is blocked by high magnetic field. In case the conductance drops to zero, the Fano factor approaches the value of $F\approx{}0.56$, with a very weak dependence on the disk radii ratio. The role of finite source-drain voltages and the system behavior upon tuning the electrostatic potential barrier from a rectangular to parabolic shape are also discussed.

The escalating demand for multifunctional and advanced materials for growing industries has turned scientific exploration to graphene-based hybrid filler polymer composites. The introduction of graphene with other fillers into polymer matrices results in astonishing properties and thus has gained significant attention in recent years. This study addresses the significance of graphene-based hybrid filler polymer composites in progressive materials science and engineering. The paper encloses some traditional and current preparation techniques employed in the fabrication of composites and a comprehensive review of successfully prepared graphene hybrid polymer composites with enhanced mechanical, thermal, and electrical properties reported in published research. The role of different factors, e.g., filler type, aspect ratios, filler-matrix compatibility, dispersion effects, homogeneity, filler orientation through polymer matrices, and curing conditions, are summarized. Finally, the applications in heavy industries, e.g., aerospace, electronics, energy storage, and automotive sectors were also analyzed. We hope this study will serve as a practical resource for new researchers and practitioners to understand and harness the full potential of these composites in various scientific and industrial fields.

Magnetic sensors are widely used in health management systems for turbomachinery, but their applications in the hot zone are limited due to the loss of magnetic properties by permanent magnets with increasing temperature. The paper presents and verifies models and design solutions aimed at improving the performance of an inductive sensor for measuring the motion of rotating objects operating at elevated temperatures (200-1000C), such as compressor and turbine blades. Physical, analog and mathematical models of the interaction of blades with the sensor were developed. A prototype of the sensor was made and its tests were carried out on the RK-4 rotor rig for the speed of 7000 rpm, in which the temperature of the sensor head was gradually increased to 1100C. The sensor signal level was compared to that of an identical sensor operating at room temperature. The heated sensor works continuously producing the output signal whose level does not change significantly. What is more, a set of six probes passed an initial engine test in an SO-3 turbojet. It was confirmed that the proposed design of the inductive sensor is suitable for blade health monitoring of the last stages of compressors, steam turbines as well as previous generation gas turbines operating below 1000C, even without a dedicated cooling system. In real-engine applications, sensor performance will depend on how the sensor is installed and the available heat dissipation capability

To clarify the relationships among critical temperature, critical magnetic field, and critical current density, this paper describes many-body interactions of quantum magnetic fluxes (i.e., vortices) and calculates pinning-related critical current density. All calculations are analytically derived, without numerical or fitting methods. Afteralculating a magnetic flux quantum mass, we theoretically obtain the critical temperature in a many-body interaction scenario (which can be handled by our established method). We also derive the critical magnetic field and inherent critical current density at each critical temperature. Finally, we determine the pinning-related critical current density with self-fields. The relationships between the critical magnetic field and critical temperature, inherent critical current density and critical temperature, and pinning critical current density and temperature were consistent with experimental observations. From the critical current density and critical magnetic field, we clarified the magnetic field transition. It appears that a magnetic flux quantum collapses when the lattice of magnetic flux quanta melts. Our results, combined with our previously published papers, provide a comprehensive understanding of the transition points in high-T_c cuprates.

Magneto-electrochemistry (MEC) is a unique paradigm in science, where electrochemical experiments are carried out as a function of an applied magnetic field, creating a new horizon of potential scientific and technological applications. Over the time, detailed understanding of this research domain was developed to identify and rationalize the possible effects exerted by a magnetic field on the various microscopic processes occurring in an electrochemical system, such as: electrolyte properties governed by charge-transfer process (electric conductivity, viscosity, and diffusivity), mass transfer, electrochemical kinetics and on the structure/quality of products formed either at the working electrode or in the electrochemical cell. Particularly, magnetic field controlled chiral architecture obtained from deposited metal, alloys and catalyst and their excellent enantio-recognition in experimental frame is highly appealing. Interestingly, Hall effect was also demonstrated in electrolytic medium via an impressive experimental technique which is being employed for further theoretical understanding in the field of magneto-electrochemical science. Later, a highly reproducible local temperature variation was observed in electrochemical electrolytes exposed to perpendicular magnetic and electric fields. However, until recent studies, none of the above mentioned reports considered the possibility of a spin-dependent related charge-transfer process. Recent experimental and theoretical studies reveal that electron’s transmission through chiral molecules is spin-selective and this effect has been referred to as chiral-induced spin-selectivity (CISS) effect. The CISS effect pave the way for the building up of a system characterized by a net magnetic moment exploiting the spin-filtering ability of chiral molecules. This interplay between chirality and magnetism may shed light on fundamental scientific aspects underlying the enantio-recognition and highly efficient electron-transfer that occurs in biological process.

We believe that a natural focus of the Physics Education Research community is on understanding and improving student learning in our physics courses. For this purpose, we are introducing smartphones in the physics laboratory. Current smartphones measure each component of the magnetic field, bearing in mind that any current perpendicular to a magnetic field produces a small potential difference, transversal to the said current, being this voltage easily measurable by Hall sensors. In this work, we have considered the magnetic field created by a linear quadrupole and we have studied its dependence on distance. Using an experimental procedure that is simple we have measured the magnetic field using the Hall sensor that most smartphones have, together with the corresponding app. The purpose of this work is to show that the laboratory is a powerful tool that increases significant learning under three conditions: 1) the practice must not be too sophisticated; 2) students must handle objects in the lab; and 3) the practice must be scientifically accurate, including the adjustments by minimum squares, and the following and necessary error calculation.

The article presents a method for obtaining new composites using a well-known mineral, expanded perlite (EP), and an industrial polymer, butadiene rubber (BR). For the design of composites, a joint oxidative chlorophosphorylation reaction of BR and EP (as well as BR and modified EP) was carried out, and the modifications obtained from this reaction were further hydrolyzed. The structure and morphology of the obtained samples were characterized in detail using Fourier transform infrared spectroscopy, ultraviolet-visible spectroscopy, X-ray powder diffraction, as well as scanning electron microscopy, and energy-dispersive X-ray analysis. EP and BR were separately modified with a similar reaction and characterized for data interpretation.

Biodegradable poly(ɛ-caprolactone) (PCL) and its composites or blends have gotten a lot of attention in the last decade because of their potential applications in human life and environmental remediation. As a result, there is a growing interest in the synthesis of PCL-composites/blends and their applications. Greater efforts have been made to develop biodegradable chemical materials as adsorbents that do not pollute the environment in order to replace traditional materials. Among the numerous types of degradable materials, PCL is currently the most promising, the most popular, and the best material to be developed, and it is referred to as the "green" eco-friendly material. Membranes and adsorbents for water treatment, packaging and compost bags, controlled drug carriers, biomaterials for tissues such as bone, cartilage, ligament, skeletal muscle, skin, cardiovascular and nerve tissues are just some of the applications of this biodegradable polymer (PCL). The goal of this review is to present a brief overview of PCL, its properties, syntheses of PCL, PCL composites, and PCL blends, but to provide a detailed investigation into the utility of PCL/PCL-based adsorbing agents in the removal of dyes/heavy metal ions.

The dolomite dust-emulsified asphalt composite with excellent mechanical properties was successfully prepared using alkali activation. The effects of different alkali concentrations and emulsified asphalt contents on the mechanical properties of the materials were studied. The mechanical properties and microstructure of the composites were analyzed using compressive strength tests, bending strength tests, and SEM characterization. The experimental results show that the specimens have excellent mechanical properties: the 7-day compressive strength can reach 76.67 MPa, and the bending strength is about twice that of silicate-based geopolymer-emulsified asphalt composite. With an increase in emulsified asphalt content, the compressive strength of the samples decreases, while the bending strength increases first and then decreases. When the emulsified asphalt content is 1%, the bending strength of the sample is up to 28.81 MPa, which is 25% higher than that of the sample without emulsified asphalt. This indicates that an appropriate emulsified asphalt content can play a toughening role in the system, providing a new idea for designing high-toughness alkali-activated materials.

Nano/micron-sized bioactive glass (BG) particles are attractive candidates for both soft and hard tissue engineering. They can chemically bond to the host tissues, enhance new tissue formation, activate cell proliferation, stimulate the genetic expression of proteins, and trigger unique an-ti-bacterial, anti-inflammatory, and anti-cancer functionalities. Recently, composites based on bi-opolymers and BG particles have been developed with various state-of-the-art techniques for tis-sue engineering. Gelatin, a semi-synthetic biopolymer, has attracted the attention of researchers because it is derived from the most abundant protein in the body, viz., collagen. It is a polymer that can be dissolved in water and processed to acquire different configurations, such as hydro-gels, fibers, films, scaffolds, etc. Searching "bioactive glass gelatin" in the tile on Scopus renders 80 highly relevant articles published in the last ~10 years, which signifies the importance of such composites. First, this review addresses the basic concepts of soft and hard tissue engineering, in-cluding the healing mechanisms and limitations ahead. Then, current knowledge on gelatin/BG composites including composition, processing and properties is summarized and discussed both for soft and hard tissue applications. This review explores physical, chemical and mechanical features and ion-release effects of such composites concerning osteogenic and angiogenic respons-es in vivo and in vitro. Additionally, recent developments of BG/gelatin composites using 3D/4D printing for tissue engineering are presented. Finally, the perspectives and current challenges in developing desirable composites for the regeneration of different tissues are outlined.

Chemical modification of cellulose offers routes for structurally and functionally diverse biopolymer derivatives for numerous industrial applications. Among cellulose derivatives, cellulose ethers have found extensive use, such as emulsifiers, in food industries and biotechnology. Methylcellulose, one of the simplest cellulose derivatives, has been utilized for biomedical, construction materials and cell culture applications. Its improved water solubility, thermoresponsive gelation, and the ability to act as a matrix for various dopants also offer routes for cellulose-based functional materials. There has been a renewed interest in understanding the structural, mechanical, and optical properties of methylcellulose and its composites. This review focuses on the recent development in optically and mechanically tunable hydrogels derived from methylcellulose and methylcellulose-cellulose nanocrystal composites. We further discuss the application of the gels for preparing highly ductile and strong fibers. Finally, the emerging application of methylcellulose-based fibers as optical fibers and their application potentials are discussed.

Conventional pervious pavement materials (PPM) consist of cement and aggregate materials and are known for poor durability due to their brittle behavior. Herein, we fabricated polymeric PPMs from durable and abundant polyurethane (PU) to enhance the durability of the material and undertook mechanical and microscopic characterizations. PU-based PPM samples with varying aggregate sizes were produced and the compressive strength and water permeability of each were examined. The pore and tortuosity characteristics of the specimens were analyzed using X-ray micro-computed tomography (micro-CT). Through the micro-CT analysis, the morphological characteristics of the internal structures of PPM were identified and the correlations between the pore size distribution, connectivity, and tortuosity within the specimen were quantitatively analyzed. The microstructures derived from micro-CT were generated as a finite element model and the stress distribution generated inside was numerically determined.

(1) Background: The diagnosis of lumbosacral radiculopathy involves anamnesis, assessment of sensitivity and strength, diagnostic imaging—usually magnetic resonance imaging (MRI)—and electrodiagnostic testing (EDX), typically electromyography (EMG) and electroneurography (ENG). MRI evaluates the structures supporting the spinal cord, while EDX evaluates root functionality. The present study aimed to analyze the concordance of MRI and EDX findings in patients with clinically suspected radiculopathy. Additionally, we investigated the comparison between these two reference tests and various clinical variables and questionnaires. (2) Methods: We designed a prospective epidemiological study of consecutive cases with an observational, descriptive, cross-sectional, and double-blind nature following the STROBE guidelines, encompassing 142 patients with clinical suspicion of lumbosacral radiculopathy. (3) Results: Of the sample, 58.5% tested positive for radiculopathy using EDX as the reference test, while 45.8% tested positive using MRI. The comparison between MRI and EDX in the diagnosis of radiculopathy in patients with clinical suspicion was not significant; the overall agreement was 40.8%. Only the years with symptoms were comparatively significant between the positive and negative radiculopathy groups as determined by EDX. (4) Conclusion: The comparison between lumbar radiculopathy diagnoses in patients with clinically suspected pathology using MRI and EDX as diagnostic modalities did not yield statistically significant findings. MRI and EDX are complementary tests assessing different aspects in patients with suspected radiculopathy; degeneration of the structures supporting the spinal cord does not necessarily imply root dysfunction.

In this paper, we introduce new formulas for calculating the restoring and repulsive magnetic forces between two non-coaxial circular loops with parallel axes. These formulas are derived from a modified version of Grover’s formula for mutual inductance between the coils in question. Utilizing these formulas, we compute the restoring and repulsive magnetic forces between two non-coaxial thick coils of rectangular cross-sections with parallel axes. In these calculations, we apply the filament method and conduct investigations to determine the optimal number of subdivisions for the coils in terms of computational time and accuracy. The method presented in this paper is also applicable to all conventional non-coaxial coils, such as disks, solenoids, and non-conventional coils like Bitter coils, all with parallel axes. This paper emphasizes the accuracy and computational efficiency of the calculations. Furthermore, the new method is validated according to several previously established methods

This article theoretically derives the magnetic field and vector potential produced by a steady current I flowing in an arbitrary plane loop at an arbitrary point r. Numerical examples are presented to demonstrate the behavior of the magnetic field produced by loops of various shapes such as polygons, circles, ellipses, and p-norm balls. Taking the limit as the loop shrinks to a point and the current I grows to infinity so that the magnetic dipole moment m of the loop (defined as the current I times the vector area of the loop) is kept constant, the magnetic field and vector potential are theoretically shown to converge to those of an ideal point magnetic dipole m.

Applications in security and electronic surveillance require combination of excellent magnetic softness with good mechanical and anti-corrosive properties and low dimensionality. We overviewed the properties of soft magnetic glass-coated microwires and different post-processing making them quite attractive for electronic article surveillance and security applications. We studied the magnetostatic interaction between the microwires and routes to tune the non-linear hysteresis loops by using the arrays of different types of amorphous microwires. The presence of neighbouring microwire (either Fe or Co-based) significantly affects the hysteresis loop of the whole microwires array. In a microwires array containing magnetically bistable microwires we observed splitting of the initially rectangular hysteresis loop with a number of Barkhausen jumps correlated with the number of magnetically bistable microwires. Essentially, non-linear and irregular hysteresis loops have been observed in mixed arrays containing Fe and Co-rich microwires. The observed non-linearity in hysteresis loops allowed to increase the harmonics and tune their magnetic field dependencies. Non-linear hysteresis loops have been also observed upon devitrification of amorphous microwires. On the other hand, several routes allowing to tune the switching field by either post-processing or modifying the magnetoelastic anisotropy have been reviewed. Observed unique combination of magnetic properties together with thin dimensions and excellent mechanical and anti-corrosive properties provide excellent perspectives for the use of glass-coated microwires for security and electronic surveillance applications.

Over the past decades, research has escalated on the use of polylactic acid (PLA) as replacement for petroleum-based polymers. This is due to its valuable properties, such as renewability, biodegradability, biocompatibility and good thermomechanical properties. Despite possessing good mechanical properties comparable to conventional petroleum-based polymers, PLA suffers from some shortcomings such as low thermal resistance, heat distortion temperature and rate of crystallization, thus different fillers have been used to overcome these limitations. In the frame work of environmentally friendly processes and products, there has been growing interest on the use of cellulose nanomaterials viz. cellulose nanocrystals (CNC) and nanofibers (CNF) as natural fillers for PLA towards advanced applications other than short-term packaging and biomedical. Cellulosic nanomaterials are renewable in nature, biodegradable, eco-friendless and they possess high strength and stiffness. In the case of eco-friendly processes, various conventional processing techniques, such as melt extrusion, melt-spinning, and compression moulding, have been used to produce PLA composites. This review addresses the critical factors in the manufacturing of PLA-cellulosic nanomaterials by using conventional techniques and recent advances needed to promote and improve the dispersion of the cellulosic nanomaterials. Different aspects, including morphology, mechanical behavior and thermal properties, as well as comparisons of CNC- and CNF reinforced PLA, are also discussed

The pursuit of an environmentally sustainable manufacturing process advocates for the substitution of harmful reagents for less damaging and recyclable solutions. This study aims to assess the effectiveness of using cellulose microfibrils synthesized via different hydrolysis reactions as reinforcing agents in polyvinyl alcohol (PVA) at varying con-centrations. The investigation explores the morphology, thermal properties, and chemi-cal behavior of the cellulose particles. The cellulose microfibrils (CMF) produced using citric acid exhibited the highest yield and aspect ratio. Notably, particles from organic acids demonstrated greater thermal stability, with oxalic acid-derived particles displaying the maximum thermal degrada-tion temperature. Subsequently, cast films of PVA reinforced with the cellulose microfibrils underwent comprehensive analyses, including Fourier transfer infrared (FTIR) spectroscopy, thermal degradation temperature (Td), differential scanning calorimetry (DSC), and tensile strength tests. The thermal behavior of cast films experienced notable changes with the addition of cellulose particles, evidenced by increased melting and crystallinity temperatures, along with a rise in the degree of crystallinity. The incorporation of cellulose particles led to a substantial improvement in mechanical properties. Films containing CMF dis-played higher Young’s modulus, and the sample incorporating 5% CMF derived from citric acid exhibited the most significant increase in modulus.

Polylactic acid (PLA) was modified with three types of MVOs, which are the epoxidized soybean oil (ESBO), maleinized sunflower oil (MSO) and maleinized olive oil (MOO), at different weight fractions. A co-rotating twin screw extruder was used to produce composite materials by melt mixing process. The effect of MVOs content, from 2.5% to 10%, on the morphology, mechanical properties, density and water absorption were investigated in detail. Addition of ESBO and maleinized vegetable oils leads to a slight decrease in density of PLA from 1.252 to 1.231 g/cm3. As the concentration of MVO in PLA increases, the amount of water absorption also increased and the highest water absorption value was observed in P10MSO. In general, the elastic modulus (EM) was slightly changed by the addition of MVO to PLA, while the tensile strength (TS) decreased. Due to the plasticizing effect of MVOs, an increase in the Izod impact strength was obtained.