In the process of oil and gas development and production, when the flow rate in the wellbore is large, the materials underground will be eroded, causing the operation to be unable to proceed smoothly and reducing the efficiency of oil and gas production. Therefore, optimizing the anti-erosion coating under high-speed flow conditions in wellbore is a very interesting thing. It can greatly improve operational efficiency. In this paper, laser cladding was used to prepare the new coating used in the PDC drill bit. Then, the effects of tungsten carbide and multi-layer graphene on the microstructure and properties of the tungsten carbide coating were studied. The research results indicate that, for new coatings, 60% tungsten carbide and 0.3% graphene are the optimal ratios. After adding WC, the hardness has significantly improved. However, when the WC content further increases more than 30%, the increase in hardness is relatively small. In addition, when the content of graphene is more than 0.3%, the branched structure became thicker, and not only the segregation of Cr, Si and W became very obvious again, but also the segregation of Fe occurred at the Ni enrichment site. The research results contribute to improving oil and gas production and operational efficiency under high-speed fluid flow conditions in the wellbore.

Dielectric elastomers, such as thermoplastic polyurethanes (TPU), are widely used as dielectric layer, emulation layer and substrate of flexible and stretchable devices. To construct capacitors and actuators that work stably upon deformation, it has become an urgent need to investigate the evolution of dielectricity under stress and strain. However, the lack of effective methods for estimating the dielectric constant of elastomers under strain poses a big challenge. This article reports a device for in-situ measuring the dielectric constant of TPU under strain. It is found that upon stretching TPU to a strain of 400%, its dielectric constant decreases from 8.47 to 2.94. In addition, combined Fourier-transform infrared spectroscopy, X-ray scattering technique, and atomic force microscopy have been utilized to characterize the evolution of microstructure under strain. The investigation under tensile strain reveals that a decreased density and average size of polarized hard domains, along with a tendency of the molecular chains to align in parallel with the tensile stress. The evolution of the microstructures results in a reduction of the dielectric constant parallel to the electric field in TPU. Our work provides valuable experimental reference for improving the stability of flexible sensors and actuators based on dielectric elastomers.

The conservation of the main protease in viral genomes, combined with the absence of a homologous protease in humans, makes this enzyme family an ideal target for developing broad-spectrum antiviral drugs with minimal host toxicity. GC-376, a peptidomimetic 3CL protease inhibitor, has shown significant efficacy against coronaviruses. Recently, a GC-376-based PROTAC was developed to target and induce the proteosome-mediated degradation of the dimeric SARS-CoV-2 3CLPro protein. Extending this approach, the current study investigates the application of the GC-376 PROTAC to the 3CPro protease of Enteroviruses, specifically characterizing its interaction with CVB3 3CPro through X-ray crystallography, NMR and biophysical techniques. The present structural data show that there are some changes between the binding of CVB3 3CPro and SARS-CoV-2 3CLPro, but the overall similarity is strong. The most notable variation is the orientation of the phenylmethyl ester of GC-376 with the S4 subsite of the proteases. This is linked to the flexibility of the protein structure around the region of the catalytic triad shown by our NMR data. Other structural variations include distinct ligand interactions in subsites S1 and S2, influenced by the presence of Glu71 in CVB3 3CPro. Despite these differences, the GC-376 PROTAC fits well within the binding sites of both proteases, demonstrating its potential as a broad-spectrum antiviral agent.

Iron oxide nanozymes are a form of nanomaterial with both superparamagnetic and enzyme-mimicking properties. Given the multifunctional nature of iron oxide nanozymes, it is attractive for creating iron oxide hybrid nanozymes through biomolecular modifications to imbue with auxillary properties. Such iron oxide hybrid nanozymes can be useful for rapid and cost-effective analysis of circulating tumor nucleic acids (ctNAs) in patient liquid biopsies during minimal residual disease (MRD) monitoring of cancer recurrence. Herein, the use of streptavidin-modified iron oxide hybrid nanozymes is reported for magnetic enrichment and bioelectrocatalytic sensing of three prostate cancer (PCa) ctRNA biomarkers with high detection specificity and sensitivity (10 copies) over an ultrabroad dynamic range (five orders of magnitude). Furthermore, the feasibility of ctRNA analysis for pre- and post-cancer treatment MRD monitoring is demonstrated using PCa urinary liquid biopsy samples.

Lipids have not traditionally been considered likely candidates for catalyzing reactions in biological systems. However, there is significant evidence that aggregates of amphiphilic compounds are capable of catalyzing reactions in synthetic organic chemistry. Here we demonstrate the potential for the hydrophobic region of a lipid bilayer to provide an environment suitable for catalysis by means of a lipozyme, or lipid aggregate capable of speeding up a chemical reaction. By bringing organic molecules into the non-polar or hydrophobic region of a lipid bilayer, reactions can be catalyzed by collections of small, nonpolar or amphiphilic molecules. We demonstrate this concept by the ester hydrolysis of calcein-AM to produce a fluorescent product, which is a widely used assay for esterase activity in cells. The reaction was first carried out in a two phase octanol-water system with the organic phase containing the cationic amphiphiles cetyltrimethylammonium bromide (CTAB) or octadecylamine. The octanol was then replaced with DOPC added to the water in the form of vesicles, where the reaction was also found to be carried out. The reaction was monitored using quantitative fluorescence which revealed catalytic turnover numbers on a scale of 10−4s−1 for each system, which is comparable to some slow enzymes. The reaction product was characterized by 1H-NMR measurements which were consistent with ester hydrolysis. The implications of thinking about lipid aggregates as catalytic entities are discussed in the context of biochemistry, pharmacology and synthetic biology.

Motivated by the PEACOC project on metal recovery from solid wastes, an innovative magnetic density separation (MDS) process has been developed for granular material sorting. It has intrinsic advantages over the existing industrialized MDS by eliminating fluid turbulence and particle jamming problems. The new MDS applies an inclined planar magnet and a horizontal basin containing a static magnetic fluid as the separation medium. A particle sliding phenomenon is identified as a feature of the process which could help the separation. The MDS successfully sorted shredded PCBAs to concentrate valuable metals and sorted shredded wires to reduce metallic contaminants in the plastic fractions. A pilot scale facility is introduced to show the design to achieve continuous production and to reduce the consumption of ferrofluid.

Whether there is any inclination between structures and functions of antimicrobial peptides (AMPs) is a mystery yet to be unraveled. AMPs have various structures associated with many different antimicrobial functions, including antibacterial, anticancer, antifungal, antiparasitic and antiviral activities. However, none has yet reported any antimicrobial functional tendency within a specific category of protein/peptide structures nor any structural tendency of a specific antimicrobial function with respect to AMPs. Here we examine the relationships between structures categorized by three structural classification methods (CATH, SCOP and TM) and seven antimicrobial functions with respect to AMPs using an enrichment analysis. The results show that antifungal activities of AMPs were tightly related to two-layer sandwich structure of CATH, knottin fold of SCOP, and the first structural cluster of TM. The associations with knottin and TM cluster 1 even sustained through the AMPs with a low sequence identity. Besides, another significant mutual enrichment was observed between the third cluster of TM and anti-gram-positive-bacterial/anti-gram-negative-bacterial activities. The findings of the structure-function inclination further our understanding of AMPs and could help us design or discover new therapeutic potential AMPs.

In this paper, a new axial-type magnetic gear with auxiliary flux-enhancing structure (AFS-AMG) is proposed. Compared to conventional AFS-AMG, it has the higher torque density and higher permanent magnet (PM) utilization factor. Firstly, the design rules and operating principles of proposed AFS-AMG are elaborated. Then, the mapping relation between the radial-type magnetic gears (RMGs) and AMGs are elucidated. Compared to its counterpart in RMGs, AFS-AMGs achieve small size. Then, the geometrical parameters of AFS-AMGs are optimized to obtain the better electromagnetic performances, where the torque density per volume and per PM volume is adopted as the evaluation standard. Finally, three different AMG topologies are constructed in finite element analysis (FEA) software for comparison. It is proven that the AFS-AMG has the largest torque density per volume and per PM volume.

In this project, four of fibers Bragg gratings were fabricated by injecting different volumes of liquids (star line Glass Mechanix optical adhesive material, olive oil diluted with ethanol) into the hollow core fiber. The amplitude splitting interferometric technique with a high resolution specially designed translation stage was used for the fabrication process. The fabrication was done using ultraviolet laser operated at wavelength 405nm. The fabricated Bragg length of the four fibers is equal to 3.8 cm. The results presented fiber Bragg grating (FBG) with successful fabrication at 653.3 nm Bragg reflected wavelength.

Background: The AR-V7 splice variant is a cause of castration-resistant prostate cancer (CRPC). However, testing for the presence of AR-V7 by RT-PCR shows AR-V7 positivity in healthy individuals. We hypothesized that the positivity reflected contamination by hematopoietic cells. We tried a novel CTC enrichment instrument using Celsee® to clear hematopoietic cells. Methods: We tested whole blood or Celsee-enriched samples for AR-V7 by RT-PCR and included samples from 41 CRPC patients undergoing sequential therapy. We evaluated the associations between AR-V7 status and clinical factors. We evaluated factors affecting AR-V7 positivity. Results: AR-V7 positivity was lower in Celsee-enriched than in whole blood specimens. AR-V7 and clinical factors did not predict the therapy effectiveness. We found no significant differences in the effectiveness of Enz/Abi upon AR-V7 evaluation. All AR-V7 positive patients had resistance to Enz/Abi. DTX, CBZ, and Radium223 treatment showed no significant difference in the treatment effectiveness, regardless of AR-V7 presence. AR-V7 was more frequently positive than EOD2 in cases with bone metastases. Conclusion: Celsee® CTC enrichment suppresses the AR-V7 false positivity. All AR-V7 positive patients presented resistance to Enz/Abi. DTX, CBZ, and Radium223 were effective and remained treatment options. AR-V7 positivity should progressively appear in patients with advanced bone metastases.

As the number of end-of-life vehicles continues to grow, the field of separation technology for broken copper and aluminium parts of end-of-life vehicles has emerged as a significant area of research. As a key technology for the separation of non-magnetic non-ferrous metals, such as copper and aluminium, eddy current separation can achieve efficient separation of non-magnetic non-ferrous metals according to their differing conductivity and density. Nevertheless, further research is required in the separation of large-scale broken copper and aluminium parts of end-of-life vehicles. This paper presents a novel magnetic roller model comprising circumferential and axial periodic arrangements of permanent magnets. A single permanent magnet was constructed as an equivalent current model, and the magnetic scalar potential equations were solved using simulation tools. This allowed the distribution of the magnetic field outside the magnetic roller to be studied. The results demonstrate that the novel permanent magnet array magnetic roller can enhance the magnetic field intensity and action distance of the external magnetic field, which is more conducive to the separation of large-scale broken copper and aluminium parts of scrap cars. The findings of this research provide a theoretical foundation for the separation of scrap car broken copper and aluminium parts.

To investigate the effect of montmorillonite on nonylphenol enrichment in a zebrafish model. The AB strain zebrafish were used as the animal subjects and three concentration gradients were set for both nonylphenol and montmorillonite, according to their actual concentrations in aquaculture water in Huzhou city. A group treated with nonylphenol alone was also set, adding up to 12 experimental groups. Concentrations of nonylphenol enriched in the liver, muscle, and gill of zebrafish were detected by solid phase microextraction–high performance liquid chromatography at Day 7, 15, and 30, respectively. Besides, the relative enzymatic activity of Superoxide dismutase (SOD) and the Glutathione S-transferase (GST) were also been detected, and the data were statistically analyzed. The results showed that the concentrations of nonylphenol in zebrafish peaked at Day 7 and gradually decreased afterwards for all the experimental groups. And the montmorillonite reduces short-term accumulation of nonylphenol in gills, and the high concentration of nonylphenol facilitates its enrichment in liver and muscle while the low concentration of nonylphenol doesn’t. Meanwhile, the low concentration of nonylphenol in liver exerts an influence on the inductive effect of SOD and GST while the high concentration of nonylphenol shows the inhibiting effect of SOD and GST.

This is a report on a dynamic autonomous magnetic interaction which does not depend on polarities resulting in short ranged repulsion involving one or more inertial bodies and a new class of bound state based on this interaction. Both effects are new to the literature, found so far. Experimental results are generalized and reported qualitatively. Working principles of these effects are provided within classical mechanics and found consistent with observations and simulations. The effects are based on the interaction of a rigid and finite inertial body (an object having mass and moment of inertia) endowed with a magnetic moment with a cyclic inhomogeneous magnetic field which does not require to have a local minimum. Such a body having some DoF involved in driven harmonic motion by this interaction can experience a net force in the direction of the weak field regardless of its position and orientation or can find stable equilibrium with the field itself autonomously. The former is called polarity free magnetic repulsion and the latter magnetic bound state. Experiments show that a bound state can be obtained between two free bodies having magnetic dipole moment. Various schemes of trapping bodies having magnetic moments by rotating fields are realized as well as rotating bodies trapped by a static dipole field in presence of gravity. Also, a special case of bound state called bipolar bound state between free dipole bodies is investigated.

It is of great academic significance to understand how the atomic structure of interfaces and boundaries in materials impacts the magnetic coupling nature across the boundaries and encourage development of state-of-the-art magnetic devices. Here, we carry out a systematic investigation of the atomic and electronic structures of twin boundaries (TBs) in LiFe5O8 thin films and determine their concurrent magnetic couplings using atomic-resolution transmission electron microscopy and atomistic first-principles calculations. The results show ferromagnetic or antiferromagnetic coupling can exist across the different TBs in LiFe5O8 (LFO) thin films and electrical structures within a few atomic layers directly rely on the TB atomic core structures. Uncovering one-to-one relationship between the magnetic properties of individual TB and the local atomic structures will clarify a thorough comprehension of numerous fascinating magnetic properties of commonly utilized magnetic materials, which will undoubtedly encourage the progress of sophisticated magnetic materials and devices.

Pyrethroid pesticides (PYRs) as the third most widely used pesticides, following organophosphorus and carbamate pesticides, which are of significant importance in the analysis and detection of vegetables. However, the current pretreatment technology for PYRs confronts challenges of difficult separation and low enrichment efficiency, resulting in a cumbersome and time-consuming pretreatment process with poor selectivity. Here, a simple and efficient magnetic solid-phase extraction (MSPE) strategy was developed to simultaneously purify and enrich five PYRs in vegetables, with the magnetic covalent organic framework nanomaterial COF-SiO2@Fe3O4 as an adsorbent. The COF-SiO2@Fe3O4 was prepared by a simple solvothermal conditions method, using Fe3O4 as magnetic core, benzidine and 3,3,5,5-tetraaldehyde biphenyl as two building units. COF-SiO2@Fe3O4 could effectively capture the targeted PYRs by virtue of its abundant π-electron system and hydroxyl groups. The impact of various experimental parameters on extraction efficiency was investigated to optimize the MSPE conditions, including adsorbent amount, extraction time, elution solvent type and elution time. Subsequently, method validation was conducted under the optimal conditions in conjunction with gas chromatography-mass spectrometry (GC-MS). Within the range of 5.00–100 μg·kg-1 (1.00–100 μg·kg-1 for bifenthrin and 2.5–100 μg·kg-1 for fenpropathrin), the five PYRs exhibited a strong linear relationship, with determination coefficients ranging from 0.9990 to 0.9997. The limits of detection (LODs) were 0.3–1.5 μg·kg-1, and the limits of quantification (LOQs) were 0.9–4.5 μg·kg-1. The recoveries were 80.2–116.7% with relative standard deviations (RSDs) below 7.0%. Finally, COF-SiO2@Fe3O4, NH2-SiO2@Fe3O4 and Fe3O4 were compared as MSPE adsorbents for PYRs. The results indicated that COF-SiO2@Fe3O4 was an efficient and rapid selective adsorbent for PYRs. This method holds promising prospects for the determination of PYRs in real samples.

Background: Multifunctional nanoparticles are known for their wide range of biomedical applications. Controlling the magnetic properties of these nanoparticles is imperative for various applications, including therapeutic angiogenesis. The study was performed to evaluate the magnetic properties and their control mechanisms by the external magnetic field. Methods: A 100nm magnetic nanoparticle was placed in the magnetic field, and parametrically the magnet field strength and distance was evaluated. Various models of magnetic strength and disposition were evaluated. Magnetic flux density, force/weight, and magnetic gradient strength were the parameters evaluated in electromagnetic computational software. Results: The seven-coil method with three centrally placed coils as Halbach array, and each coil with a flux density of 7 Tesla, and with a coil dimension of 20cmx20cm (square model) of each coil showed a good magnetic strength and force/weight parameters in a distance of 15cm from the centrally placed coil. The particles were then evaluated for their motion characteristics in saline. It showed good displacement and acceleration properties. After that, the particles were theoretically assessed in a similar mathematical model after parametrically correcting the drag force. After application of high drag forces, the particles showed adequate motion characteristics. When the particle size was reduced further, the motion characteristics were preserved even with high drag forces. Conclusion: There is potential for a novel method of controlling multifunctional magnetic nanoparticles using high magnetic fields. Further studies are required to evaluate the motion characteristics of these particles in-vivo and invitro.

The state detection of power cable is very important to ensure the reliability of power supply. Traditional sensors are mostly based on electric field detection, the operation is complex, and its efficiency needs to be improved. This paper optimizes the design and development of the magnetic field detection sensor for AC power cables. Firstly, through the establishment of the magnetic field sensor model, it is determined that permalloy is the material of the magnetic core, the optimal aspect ratio of the magnetic core is 20, and the ratio of coil length to core length is 0.3. Secondly, the coil simulation model is established, and it is determined that the optimal number of turns of the coil is 11000 turns, the diameter of the enamelled copper wire is 0.08mm, and the equivalent magnetic field noise of the sensor is 0.06pT. Finally, the amplifying circuit based on negative magnetic flux feedback is designed and the sensor is assembled, and the experimental circuit is built for sensitivity test. the results show that the sensitivity of the magnetic field sensor is 327.6mV/μT. The sensor designed in this paper has the advantages of small size, high sensitivity, easy to carry and high reliability.

The spread of micro- (MPs) and nanoplastics (NPs) in the environment has become a significant environmental concern, necessitating effective removal strategies. In this comprehensive scientific review, we examine the use of magnetic nanoparticles (MNPs) as a promising technology for the removal of MPs and NPs from water. We first describe the issue of MPs and NPs and their impact on the environment and human health. Then the fundamental principles of using MNPs for the removal of these pollutants will be presented, emphasizing that MNPs enable selective binding and separation of MPs and NPs from water sources. Furthermore, we provide a short summary of various types of MNPs that have proven effective in the removal of MPs and NPs. These include ferromagnetic nanoparticles, MNPs coated with organic polymers, as well as nanocomposites and magnetic nanostructures. We also review their properties, such as magnetic saturation, size, shape, surface functionalization and stability, and their influence on removal efficiency. Next, we describe different methods of utilizing MNPs for the removal of MPs and NPs. We discuss their advantages, limitations, and potential for further development in detail. In the final part of the review, we provide an overview of existing studies and results demonstrating the effectiveness of using MNPs for the removal of MPs and NPs from water. We also address challenges that need to be overcome, such as nanoparticle optimization, process scalability, and the removal and recycling of nanoparticles after the completion of the process. This comprehensive scientific review offers an extensive insight into the use of MNPs for the removal of MPs and NPs from water. With improved understanding and the development of advanced materials and methods, this technology can play a crucial role in addressing the issue of MPs and NPs and preserving a clean and healthy environment.

Among earth’s microbial populations are the genes, functional capacities, generational memory and sentient cognition that enable microorganisms to adapt and thrive in the full range of ecological conditions found on planet earth. In prior sequential publications, we considered fundamental properties (e.g., use of and responses to sound, light, vibrations) and features of microorganisms that cause them to be critical co-partners of human and other holobionts as well as the potential benefits for humanity that can be gained by fully applying quantum-related and novel capacities of microbial life. In this narrative review we: 1) discuss key concepts concerning a microbially-enhanced and sustainable future, and 2) focus on electric- and magnetic- based features of microorganisms that make them pivotal for myriad benefits ranging from beyond pharma-based health and wellness to free- and/or renewable energy and restorative agriculture to improved human networking. While the benefits are many, the risks posed by hazardous electric or magnetic field exposures to both holobionts and microbial communities are significant. This review concludes that microbes and their remarkable capacities offer both humanity and the planet a much brighter future if we reverse the demonization of microbes and wanton microbiome degradation that has predominated much of the past century.

(1) Background: The aim of the research was to present and emphasize the importance of magnetic resonance imaging (MRI) in diagnosing Achilles tendon (AT) ruptures by presenting case reports. (2) Materials and Methods: The sample of respondents included 7 patients (4 males and 3 females, 2 athletes and 5 non-athletes), aged 25 to 58 years, with AT injuries, who were examined and treated at the Institute for Treatment and Rehabilitation "Niška Banja", Niš, Serbia. Ankle examinations with MRI were conducted using the Esaote O-scan 0.3 T machine. The examinations were performed without the application of a paramagnetic contrast agent and without the use of anesthesia. Results: The MRI method's sensitivity and overall diagnostic accuracy were excellent, with 100% true positives. In our study, the method accurately detected the presence, location, and severity of AT injuries in all cases. MRI is an important and reliable method for detecting AT injuries, classifying them, monitoring the course of recovery, and assessing the effects of therapy. Conclusions: An unrecognized or delayed diagnosis of an AT injury can lead to chronic changes. Timely diagnosis (clinical examination, ultrasonography, magnetic resonance imaging) and appropriate treatment (conservative or operative) enable patients to return to normal activities, including sports. Unfortunately, the use of MRI is limited by restricted access and the cost of the examination.

Sepsis is a life-threatening syndrome triggered by infection and accompanied by high mortality, with antimicrobial resistances (AMRs) further escalating clinical challenges. Rapid and reliable detection of causative pathogens and AMRs are key factors for fast and appropriate treatment, in order to improve outcome in septic patients. However, current sepsis diagnostics based on blood culture is limited by low sensitivity and specificity while current molecular approaches fail to enter clinical routine. Therefore, we developed a Suppression PCR-based selective enrichment sequencing approach (SUPSETS), providing a molecular method combining multiplex suppression PCR with Nanopore sequencing to identify most common sepsis-causative pathogens and AMRs using plasma cell-free DNA. Applying only 1 mL of plasma, we target eight pathogens across three kingdoms and ten AMRs in a proof-of-concept study. SUPSETS was successfully tested on first ten clinical samples and revealed comparable results to clinical metagenomics while clearly outperforming blood culture. Several clinically relevant AMRs could be detected additionally. Furthermore, SUPSETS provided first pathogen and AMR-specific sequencing reads within minutes of starting sequencing, thereby potentially decreasing time to results to 11 - 13 hours and suggesting diagnostic potential in sepsis.

Osteosarcoma is the most common subtype of primary bone cancers, affecting mostly adolescents. In recent years, several studies have focused on elucidating the molecular mechanisms of this sarcoma; however, its molecular etiology has still not been determined with precision. Therefore, we applied a consensus strategy with the use of several bioinformatics tools to prioritize genes involved in its pathogenesis. Subsequently, we assessed the physical interactions of the previously selected genes and applied a communality analysis to this protein-protein interaction network. The consensus strategy prioritized a total list of 553 genes. Our enrichment analysis validates several studies that describe the signaling pathways PI3K/AKT and MAPK/ERK as pathogenic. The gene ontology described TP53 as a principal signal transducer that chiefly mediates processes associated with cell cycle and DNA damage response It is interesting to note that the communality analysis clusters several members involved in metastasis events such as MMP2 and MMP9 and genes associated with DNA repair complexes, like ATM, ATR, CHEK1, and RAD51. In this study, we could identify well-known pathogenic genes for osteosarcoma and prioritized genes that need to be further explored.

Previous evidence links the formation of extranuclear inclusions of transcription factors, such as ERK, Jun, TDP-43, and REST with oxidative, endoplasmic-reticulum, proteasomal, and osmotic stress. To further characterize its extranuclear location, we performed a high-content screening based on confocal microscopy and automatized image analyses of an epithelial cell culture treated with hydrogen peroxide, thapsigargin, epoxomicin, or sorbitol at different concentrations and times to recreate the stresses mentioned above. We also performed subcellular fractionation of the brain from transgenic mice overexpressing the Q331K mutated TARDBP, and we analyzed REST-regulated mRNAs. The results show that these nuclear proteins exhibit a mitochondrial location, together with significant nuclear/extranuclear ratio changes, in a protein and stress-specific manner. The presence of these proteins in enriched mitochondrial fractions in vivo confirmed the results of image analyses. TDP-43 aggregation was associated with alteration in mRNA levels of REST target genes involved in calcium homeostasis, apoptosis, and metabolism. In conclusion, cell stress increased mitochondrial translocation of nuclear proteins, increasing the chance of proteostasis alterations. Further, TDP-43 aggregation impacts REST target genes, disclosing an exciting interaction between these two transcription factors in neurodegenerative processes.

Pore structure characterization and fractal analysis have great significance for understanding and evaluating tight limestone reservoirs. In this work, the pore structure of tight limestone is characterized combined with low-temperature nitrogen adsorption (LTNA) and low-field nuclear magnetic resonance (NMR), and the fractal dimension of tight limestone pore structure is discussed based on LTNA and NMR data. The results indicate that the pores of tight limestone have H3 and H4 types, the pore size distribution (PSD) of H3 type is a wave distribution ranging from 2 to 10 nm, and the PSD of H4 type is a unimodal distribution ranging from 2 to 10 nm. The transverse relaxation time (T2) spectrum of tight limestone shows single peak (DF), double peak (SF) and three peak (TF), and the T2 spectrums for micropores, mesopores and macropores range from 0.1 to 10 ms, from 10 to 100 ms, and greater than 100 ms, respectively. The LTNA fractal dimension of tight limestone (DL) ranges between 2.4446 and 2.7688, with an average of 2.5729, and the NMR fractal dimensions of micropores (DNMR1), mesopores (DNMR2) and macropores (DNMR3) are distributed between 0.3744 to 1.1293, 2.4263 to 2.9395 and 2.6582 to 2.9989, respectively. Moreover, there is no correlation between fractal dimension and permeability and porosity, a negative correlation between DL and average pore radius, a positive correlation between DL and specific surface area, and a positive correlation between DNMR2 and DNMR3 and micropore content, while DNMR2 and DNMR3 are negatively correlated with the content of mesopores and macropores.

There is currently no unified explanation for the origin of Earth's magnetic field, planetary magnetic fields, stellar magnetic fields, and neutron star magnetic fields, and most importantly, none of these theories have been experimentally verified. This paper is based on a new unified theory of mechanics and its derived applications, which may provide a better explanation for the origin of magnetic fields in celestial bodies and can be experimentally tested to better answer the observed phenomena: (1) the greater the mass of the celestial body, the stronger the magnetic field; (2) the faster the rotation speed of the celestial body, the stronger the magnetic field; (3) the higher the density of the celestial body, the stronger the magnetic field produced.

The carbonyl iron particles were dispersed in a polychloroprene rubber (CR) matrix under an external magnetic field for practical application as microwave absorption composites film. The film prepared under external magnetic field with a thickness of only 0.54 mm showed least reflection loss of -15.98 dB and the reflection loss value less than -10.0 dB over the frequency range of 11.4~14.8 GHz. In comparison with the microwave absorption properties of calculation by transmission line theory based on the tested relative complex permittivity and permeability and film prepared by general route without external magnetic field, the film made with external magnetic field exhibited more excellent microwave absorption properties, strongly depending on the increment of anisotropy and rearrangement of magnetic particles. The results indicated the composite film made under external magnetic field have excellent microwave absorption properties, which suggest that the composites thin film could be used as a thinner and lighter microwave absorber.

The separation and enrichment can be targeted to enrich the rare and precious metals in fly ash and reduce the cost of leaching and recovering of fly ash. Regarding their different properties, the single-component separation was used to obtain uncompleted burned carbon, glass microbeads, minerals, and other characteristic components from the ash. Also, the mineral composition of each component was analyzed by electron microscopy. The metal minerals were mainly concentrated in the mineral components. Besides, the electron probe micro-analysis shows that the Pt content in the minerals of fly ash was significantly correlated with the metal contents of Ni and Cu. After the obtainment of the characteristics of fly ash metal enrichment, the heavy minerals with Cu, Ni, Pt, Pd, and other target metal elements were enriched by gravity separation and flotation. The enrichment coefficients of Cu, Ni, Pt, and Pd were 1.45, 1.33, 1.90 and 1.60, respectively, and the recovery rates were 77%, 81%, 97% and 88% respectively. Since the yield of heavy minerals obtained by separation was 62.24%, it indicated the physical separation method could significantly reduce the cost of leaching and recovering of fly ash metal resources.

The direct growth of single-walled carbon nanotubes (SWCNTs) with a narrow distribution of diameter or chirality remains elusive despite significant benefits in properties and applications. Nanoparticle catalysts are vital for SWCNT synthesis, but how to precisely manipulate their chemistry, size, concentration, and deposition remains difficult, especially within a continuous production process from the gas-phase. Here, we demonstrate the preparation of W₆Co₇ alloyed nanoparticle catalysts with precisely tunable stoichiometry using electrospray, which remain solid state during SWCNT growth. We also demonstrate continuous production of liquid iron nanoparticles with in-line size selection. With the precise size manipulation of catalysts in the range of 1-5 nm, and a nearly monodisperse distribution (σ_g < 1.2), an excellent size selection of SWCNT can be achieved. All of the presented techniques show great potential to facilitate the realization of single-chirality SWCNT production.

In the former mining district of La Carolina (southern Spain), waste materials were accumulated without first waterproofing the substrate. Additionally, these mining dams were abandoned without any type of restoration, conditions that present a significant risk of contaminating the surrounding soils and waters. Prior to carry out the necessary works for isolating these residues, morphological characterization of the contact with the base substrate is needed. For that purpose, in recent years, different indirect study techniques have been used, among which electrical to-mography stands out. In this work, a less common geophysical technique, magnetometry, both in its magnetic and gra-diometric modalities, is used as an alternative method to analyse the geometry and structure of a mining dam. The results obtained with this methodology are compared with the results provided by electrical techniques, as well as with direct data from mechanical surveys and aerial photo-graphs prior to waste deposition. The magnetic anomaly curves obtained with geometric models generated with the Mag2dc program were also analysed. This comparative study shows the use-fulness of magnetic prospecting in characterizing the base geometry of these mining structures and therefore the interest in its application to environmental characterization studies.

The Paris Agreement aims to limit global warming, and one of the most pollutant sectors is heavy industry, where cement production is a significant contributor. This work briefly explores some alternatives: recycling, reducing clinker content, waste heat recovery, and carbon capture, discussing their advantages and drawbacks. Then, it examines the economic viability and benefits of increasing oxygen concentration in the primary burning air from 21% to 27%, which could improve clinker production by 7%, and the production of hydrogen through PEM electrolysis to make up 5% of the fuel thermal fraction, both on a cement plant producing 3000 tons of clinker per day. It is concluded that oxygen enrichment can provide substantial fuel savings for a relatively low cost despite a possible significant increase in NOx emissions. By opposition, hydrogen production at this scale does not appear economically viable.

Hyperspectral reflectance imaging is an emerging method for rapid non-invasive quantitative screening of plant traits. This method is essential for high-throughput phenotyping and hence for accelerated breeding of crop plants as well as for precision agriculture practices. However, extraction of sensible information from reflectance images is hindered by the complexity of plant optical properties, especially when they are measured in the field. We propose using reflectance indices (Plant Senescence Reflectance Index, PSRI; Anthocyanin Reflectance Index, ARI; and spectral deconvolution) previously developed for remote sensing of vegetation and point-based reflectometers to infer the spatially resolved information on plant development and biochemical composition using ripening apple fruit as the model. Specifically, the proposed approach enables capturing data on distribution of chlorophylls and primary carotenoids as well as secondary carotenoids (both linked with fruit ripening and leaf senescence during plant development) as well as the information on spatial distribution of anthocyanins (known as stress pigments) over the plant surface. We argue that the proposed approach would enrich the phenotype assessments made on the base of reflectance image analysis with valuable information on plant physiological condition, stress acclimation state, and the progression of the plant development.

Gold, present as electrum, in the Battle Gap, Ridge North-West, HW, and Price deposits at the Myra Falls mine, occurs in late veinlets cutting the earlier VMS lithologies. The ore mineral assemblage containing the electrum comprises dominantly galena, tennantite, bornite, sphalerite, chalcopyrite, pyrite and rare stromeyerite is defined as an Au-Zn-Pb-As-Sb association. The gangue is comprised of barite, quartz, and minor feldspathic volcanogenic sedimentary rocks and clay. Deposition of gold as electrum in the baritic upper portions of the sulphide lenses occurs at relatively shallow water depths beneath the sea floor. Primary, pseudosecondary, and secondary fluid inclusions, petrographically related to gold, show boiling fluid inclusion assemblages in the range of 123 to 173 °C, with compositions and eutectic melt temperatures consistent with seawater at approximately 3.2 wt% NaCl equivalent. The fluid inclusion homogenization temperatures are consistent with boiling seawater corresponding to water depths ranging from 15 to 125 metres. Slightly more dilute brines corresponding to salinities of approximately 1 wt% NaCl indicate that there is input from very low-salinity brines, which could represent a transition from subaqueous VMS to epithermal-like conditions for precious metal enrichment, mixing with re‑condensed vapour, or very low-salinity igneous fluids.

The presented work offers a novel process scheme for valorizing historical Pb-Zn slag, which involves crushing, grinding, and then using separation techniques to concentrate valuable components (nonferrous metals). This methodology could have a significant impact on the global beneficiation of metallurgical slags since, in theory, it is significantly more simple, environmentally friendly, and cost-effective than standard pyrometallurgical or hydrometallurgical procedures. According to previous physicochemical and mineralogical studies, Pb-Zn slag from "Topilnica" Veles is a valuable secondary raw material. This inhomogeneous technogenic resource contains substantial amounts of nonferrous metals (Pb, Zn, Cu, and Ag). However, laboratory tests have indicated that the Pb-Zn slag contains a very uneven valuable metals amounts, ranging from several g/ton to several tens of g/ton. The main issue is that traditional metallurgical procedures for releasing beneficial elements are not commercially viable since the valuable elements are "trapped" within amorphous aluminosilicates or intergrowths of alloy grains and glassy phases. Gravity concentration (Wilfley 13 shaking table) and magnetic separation (Davis separator and disk separator) were used to obtain the final concentrate following comminution and grindability testing. The gravity concentration proved more effective. This streamlined approach of valorizing Pb-Zn slag can reduce the need for hazardous chemicals used in hydrometallurgical refinement operations, as well as the extremely high temperatures required for pyrometallurgical processing. This is the first investigation into the feasibility of this novel approach, which includes direct investigations of the Pb-Zn slag feed using these alternative technologies. After extracting the valuable metals, the amorphous aluminosilicate part of the Pb-Zn slag can be reapplied as an alternative raw material in the building sector, adding to the circularity of the suggested approach..

Nowadays, the development of civilization requires a vision of balancing the interests of employees and employers in the sphere of work as never before. Work-life balance is directly linked to social sustainability. The aim of this article is to analyse various dimensions of mutual enrichment of the professional and private life of an individual and to describe how positive experiences in professional and non-professional life influence the improvement of satisfaction, health and achievements, thus enabling the sustainable development of the individual. The conducted research was of a qualitative nature. Thematic exploration was used to analyse the findings of 34 in-depth interviews with experienced HR managers and employees at various levels of enterprises in Poland. The research shows that the work and personal life of the respondents interact, complement, and enrich in different ways, depending on the stage of the employee’s life. Habits developed by practicing a specific sport discipline or other type of hobby are helpful in the effective implementation of professional tasks. Also, non-professional interests, including communing with culture and art have a positive impact on professional activities. On the other hand, the respondents emphasized that thanks to their professional activities, specific to the type of work they perform, they are sometimes more extroverted, meticulous, organized and consistent when performing activities outside of work and in other aspects of private life.

The influence of post-processing conditions on the magnetic properties of amorphous and nanocrystalline microwires have been thoroughly analyzed, paying attention on the influence of magnetoelastic, induced and magnetocrystalline anisotropies on the hysteresis loops of Fe-, Ni- and Co-rich microwires. We showed that magnetic properties of glass-coated microwires can be tuned by the selection of appropriate chemical composition and geometry in as-prepared state or further considerably modified by appropriate post-processing, which consists of either annealing or glass-coated removal. Furthermore, stress-annealing or Joule heating can further effectively modify the magnetic properties of amorphous magnetic microwires owing to induced magnetic anisotropy. Devitrification of microwires can be useful for either magnetic softening or magnetic hardening of the microwires. Depending on the chemical composition of the metallic nucleus and on structural features (grain size, precipitating phases) nanocrystalline microwires can exhibit either soft magnetic properties or semi-hard magnetic properties. We demonstrated that the microwires with coercivities from 1 A/m to 40 kA/m can be prepared.

A single water pollution by dyes is a huge environmental problem; there is a necessity to produce new decolorization methods that are effective, cost-attractive, and suitable in industrial use. Magnetic chitosan polymers offer the advantage of easy separation from the dye solution. In this work, a Chitosan-Fe polymer was synthesized, characterized, and tested for removal of the azo dye Direct Red 83:1 from water. The polymer was characterized in terms of surface morphology (SEM), elemental analysis (EA), differential scanning calorimetry (DSC), thermal gravimetric analysis (TGA), infrared spectrophotometry (IR), X-ray powder diffraction (XRD) and density functional theory (DFT). The reported results hint that 1 g and pH 7.0 were the best conditions to carry out both kinetic and isotherm models. To understand the adsorption behavior of Direct Red 83:1 onto the polymers, adsorption rate and maximum adsorption capacity were calculated using kinetic tests and isotherm curves respectively. The kinetic data and mechanism of the adsorption process were analyzed by three models and the equilibrium data by three adsorption isotherms. The results indicated that the adsorption process follows a pseudo-second-order kinetics (R2= 0.999) and fits the Temkin isotherm (R2= 0.946), indicating that the adsorption occurred on heterogeneous surfaces. The newly synthesized Chitosan-Fe polymer exhibited good adsorption properties and easy separation of cleaned water.

In the study of relativistic jets one of the key open questions is their interaction with the environment on the microscopic level. Here, we study the initial evolution of both electron–proton (e^- - p⁺) and electron–positron (e^±) relativistic jets containing helical magnetic fields, focusing on their interaction with an ambient plasma. We have performed simulations of "global" jets containing helical magnetic fields in order to examine how helical magnetic fields affect kinetic instabilities such as the Weibel instability, the kinetic Kelvin-Helmholtz instability (kKHI) and the Mushroom instability (MI). In our initial simulation study these kinetic instabilities are suppressed and new types of instabilities can grow. In the e^- - p⁺ jet simulation recollimation-like instability occurs and jet electrons are strongly perturbed. In the e^± jet simulation a recollimation-like instability occurs at early times followed by a kinetic instability and the general structure is similar to a simulation without helical magnetic field. Simulations using much larger systems are required in order to thoroughly follow the evolution of global jets containing helical magnetic fields.

The bipartite entanglement is comprehensively investigated in the mononuclear molecular complex (Et3NH)[Ni(hfac)2L], where HL denotes 2-(2-hydroxy-3-methoxy-5-nitrophenyl)-4,4,5,5-tetramethyl-4,5-dihydro-1H-imidazol-3-oxide-1-oxyl and hfacH stands for hexafluoroacetylacetone. From the magnetic point of view, the molecular compound (Et3NH)[Ni(hfac)2L] consists of an exchange-coupled spin-1 Ni2+ magnetic ion and a spin-12 nitronyl-nitroxide radical substituted nitrophenol. The nickel-radical molecular complex affords an experimental realization of a mixed spin-(12, 1) Heisenberg dimer with a strong antiferromagnetic exchange coupling J/kB= 505 K and two distinct g-factors gRad=2.005 and gNi=2.275. By adopting this set of magnetic parameters we demonstrate that the Zeeman splitting of a quantum ferrimagnetic ground-state doublet due to a weak magnetic field may substantially reinforce the strength of bipartite entanglement at low temperatures. The molecular compound (Et3NH)[Ni(hfac)2L] maintains sufficiently strong thermal entanglement even at room temperature, vanishing only above 546 K. Specifically, the thermal entanglement in the nickel-radical molecular complex retains approximately 40% of the maximum value corresponding to perfectly entangled Bell states at room temperature, which implies that this magnetic compound provides suitable platform of a molecular qubit with potential implications for room-temperature quantum computation and quantum information processing.

This study explores advanced feature engineering and semantic enrichment methods to enhance text classification, focusing on detecting figurative language in tweets. The novel features introduced, Syno\_Lower\_Mean and Syn\_Mean, measure the use of uncommon synonyms and the mean frequency of synonyms, capturing semantic richness crucial for detecting figurative expressions. Using resources like SenticNet and Framester, we enrich our feature set with sentiment and frame semantic information. Our approach includes extensive data preprocessing, sophisticated feature selection, and implementing various classification models, such as SVM, KNN, Logistic Regression, Decision Trees, Random Forest, BERT, and LSTM networks. We rigorously evaluate each model's performance to assess the effectiveness of our features and enrichment methods. Putting emphasis on model explainability, we use decision tree analysis, feature importance analysis, and the TREPAN algorithm to approximate SVM decisions. Although we focus on figurative language detection, our methods have broader implications for various NLP text classification tasks. Our findings demonstrate significant improvements in classification accuracy and interpretability through innovative feature design and dataset enrichment.

Neural precursors (NPs) present in the hippocampus can be modulated by several neurogenic stimuli including environmental enrichment (EE) and antidepressant treatment acting through BDNF-TrkB signaling. We have recently identified NPs in meninges, however menigneal niche response to pro-neurogenic stimuli has never been investigated. To this aim, we analyzed the effects of 4 weeks fluoxetine administration or 1 week EE treatment on NP distribution in mouse brain meninges. Following neurogenic stimuli, although we did not detect modification of meningeal cell number and proliferation, we observed, in meninges, an increased number of β3-Tubulin⁺ immature neuronal cells. Lineage-tracing experiment confirmed that EE-induced β3-Tubulin⁺ immature neuronal cells present in meninges originated from GLAST⁺ radial glia cells. To investigate the molecular mechanism responsible for this response, we studied the BDNF-TrkB interaction. Treatment with ANA-12, a TrkB non-competitive inhibitor, abolished the EE-induced increase of β3-Tubulin⁺ immature neuronal cells in meninges.Overall these data showed, for the first time, that the meningeal niche responded to neurogenic stimuli by increasing the immature neuronal population through TrkB-mediated signaling. A better understanding of the neurogenic stimuli effects on NPs in meninges may be useful to improve the effectiveness of depression and mood disorders treatments.

In view of the problem that the output thrust of solenoid actuator is affected by various factors and is difficult to calculate in actual working conditions, this paper proposes a semi-analytical model constructed by magnetic field subdomain method with internal and external boundary conditions in cylindrical coordinate system for calculation, and the general solution equations of magnetic vector potential for each subdomain are derived and solved by MATLAB. Taking a push-pull electromagnet as an example, the finite element simulation and experimental comparative analysis are carried out. The correctness and applicable conditions of the subdomain method are illustrated by comparing the gradient plot of magnetic vector potential, inductance curve and electromagnetic force. By calculating the output thrust after considering the core gravity, spring force and electromagnetic force, it is shown that this method has the advantage of computational flexibility compared with the finite element method, and it is easier to write special algorithms according to various working conditions to calculate the important parameters in engineering applications.

Based upon Maxwell's equations, it has long been established that oscillating electromagnetic (EM) fields incident upon a metal surface decay exponentially inside the conductor, leading to a virtual EM vacuum at sufficient depths. Magnetic resonance imaging (MRI) utilizes radiofrequency (r.f.) EM fields to produce images. Here we present the first visualization of a virtual EM vacuum inside a bulk metal strip by MRI, amongst several novel findings. We uncover unexpected MRI intensity patterns arising from two orthogonal pairs of faces of a metal strip, and derive formulae for their intensity ratios, revealing differing effective elemental volumes (voxels) underneath these faces. Further, we furnish chemical shift imaging (CSI) results that discriminate different faces (surfaces) of a metal block according to their distinct nuclear magnetic resonance (NMR) chemical shifts, which holds much promise for monitoring surface chemical reactions noninvasively. Bulk metals are ubiquitous, and MRI is a premier noninvasive diagnostic tool. Combining the two, the emerging field of bulk metal MRI can be expected to grow in importance. The fundamental nature of results presented here may impact bulk metal MRI and CSI across many fields.

Highly-doped graphene samples show the conductance reduced and the shot-noise power enhanced compared to standard ballistic systems in two-dimensional electron gas. These features can be understood within a model assuming incoherent scattering of Dirac electrons between two interfaces separating the sample and the leads. Here we find, by adopting the above-mentioned model for the edge-free (Corbino) geometry and by means of the computer simulation of quantum transport, that another graphene-specific feature should be observable when the current flow through a doped disk is blocked by high magnetic field. In case the conductance drops to zero, the Fano factor approaches the value of $F\approx{}0.56$, with a very weak dependence on the disk radii ratio. The role of finite source-drain voltages and the system behavior upon tuning the electrostatic potential barrier from a rectangular to parabolic shape are also discussed.

Aims: This systematic review aims to evaluate the influence of Environmental Enrichment (EE) on oncological factors in experimental studies involving various types of cancer models. Methods: A comprehensive search was conducted in three databases: PubMed (161 articles), Embase (335 articles), and Scopus (274 articles). Eligibility criteria were applied based on the PICOS strategy to minimize bias. Two independent researchers performed the searches, with a third participant resolving any discrepancies. The selected articles were analyzed, and data regarding sample characteristics and EE protocols were extracted. The outcomes focused solely on cancer and tumor-related parameters, including cancer type, description of the cancer model, angiogenesis, tumor occurrence, volume, weight, mice with tumors, and tumor inhibition rate. Key-findings: A total of 770 articles were identified across the three databases, with 12 studies meeting the inclusion criteria for this systematic review. The findings demonstrated that different EE protocols were effective in significantly reducing various aspects of tumor growth and development, such as angiogenesis, volume, weight, and the number of mice with tumors. Furthermore, EE enhanced the rate of tumor inhibition in mouse cancer models. Findings: This systematic review highlights the significant impact of EE protocols on multiple parameters associated with tumor growth and development, including angiogenesis, occurrence, volume, weight, and tumor incidence. Moreover, EE demonstrated the potential to increase the rate of tumor inhibition. These findings underscore the importance of EE as a valuable tool in the management of cancer.

This study aimed to determine a nutritionally adequate feeding protocol for Hippocampus hippocampus juveniles. In the experimental trial, seahorses were fed copepods from 0-7 days post-parturition (DPP) and, from 8-28 DPP, four dietary treatments: (copepods (control diet), microalgae-enriched Artemia with a DHA/EPA ratio of 2:1, microalgae-enriched Artemia with a DHA/EPA ratio of 2:1 along with 5% copepods, and with 10% copepods) were tested. Results showed that juvenile seahorses fed on copepods attained a significantly higher (P&lt;0.05) growth performance (5.1 mg d-1) than fish-fed diets with 5% and 10% copepod inclusion, (3.09 and 3.07 mg d-1, respectively), and fish-fed enriched Artemia (1.83 mg d-1) which performed poorly. Data suggests that feeding copepods during the first 7 DPP promotes maturation of the digestive tract of juvenile seahorses, and the addition of a limited amount of copepods to the diet improves H. hippocampus juvenile growth performance when compared to the use of Artemia as a single diet due to the improvement of the essential fatty acid profile in the diets.

We report an easy-to-implement device for SERS-based detection of various analytes dissolved in water droplets at trace concentrations. The device combines an analyte-enrichment system and SERS-active sensor site, both produced via inexpensive and high-performance direct fs-laser printing. Fabricated on a surface of water-repellent polytetrafluoroethylene substrate as an arrangement of micropillars, the analyte-enrichment system supports evaporating water droplet in the Cassie-Baxter superhydrophobic state, thus ensuring delivery of the dissolved analyte molecules towards the hydrophilic SERS-active site. The efficient pre-concentration of the analyte onto the sensor site based on densely-arranged spiky plasmonic nanotextures results in its subsequent label-free identification by means of SERS spectroscopy. Using the proposed device, we demonstrate reliable SERS-based fingerprinting of various analytes, including common organic dyes and medical drugs at ppb concentrations. The proposed device is believed to find applications in various areas, including label-free environmental monitoring, medical diagnostics, and forensics.

Lacunary polyoxometalates (POMs) are negatively charged metal−oxo clusters, formally obtained from plenary topologies via fragment removal. Owing to the fragment removal, the lacunary POMs archetypes are rich in nucleophilic terminal oxo ligands, making them suitable for post-synthetic coordination with various heterometals. Trilacunary heteropolytungstates (het-ero-POTs) based on bowl-shaped {W9O30} framework incorporating a central lone-pair containing {XO3} hetergroup (X = AsIII, SbIII, and BiIII) function as all-inorganic scaffolds that in the presence of d-block metal cations typically construct sandwich-like dimers of Hervé and/or Krebs. Herein we review the preparative approaches, compositional and magnetic versatility of the constructing Hervé and Krebs type dimers and discuss prospective use as POMtronics.

Faraday's Law of induction is often stated as "a change in magnetic flux causes an EMF"; or, more cautiously, "a change in magnetic flux is associated with an EMF"; It is as well that the more cautious form exists, because the first "causes" form can be shown to be incompatible with the usual expression for EMF. This is not, however, to deny the causality as reasonably inferred from experimental observation ­ it is the equation for Faraday's Law of induction which does not represent the claimed cause-and-effect relationship. Here we investigate a selection of different approaches, trying to see how an explicitly causal mathematical equation, which attempts to encapsulate the "a change in magnetic flux causes ..." idea, might arise.

Commercial formulates of beneficial microbes have been used to enrich the rhizosphere microbiome of tomato plants grown in pots located in a glasshouse. These plants have been subjected to attacks by soil-borne parasites, such as root-knot nematodes (RKNs), and herbivores, such as the miner insect Tuta absoluta. The development of both parasites and the symptoms of their parasitism were restricted in these plants with respect to plants left untreated. A mixture, named in the text as Myco, containing plant growth promoting rhizobacteria (PGPR), opportunistic biocontrol fungi (BCF), and arbuscular mycorrhizal fungi (AMF) was more effective in limiting pest damages than a formulate containing the sole AMF (Ozor). Therefore, Myco-treated plants inoculated with RKNs were taken as a model to further study which biocontrol agent (BCA) was specifically responsible of plant immunization and the molecular pathways exploited to achieve such an immunization. The PGPR contained in Myco were not able to reduce nematode infection, rather, they worsened symptoms on plants, compared with those observed on untreated plants. When plants were treated with suspensions of Bacillus subtilis at concentrations similar to those provided with Myco and then inoculated with RKNs, infection was actually more severe than that on untreated plants. Therefore, it was argued that both BCF and AMFwere the microorganisms that, colonizing roots, synergistically stimulate plant immune system against RKNs. Beneficial fungi lowered the activities of the defense supporting enzymes endochitinases and β-1,3-glucanase to be able to colonize the roots. However, as early as three days after nematode inoculation, these enzyme activities, and the expression of the encoding pathogenesis related genes (PR-2, PR-3) were found to be enhanced in roots with respect to not inoculated plants, thus indicating that plants had been primed against RKNs. Addition of paclobutrazol, which reduced salicylic acid (SA) levels in cells, and of diphenyliodonium chloride, which inhibits superoxides generation, completely abolished the repressive effect of Myco on nematode infection and presumably plant immune reaction. Inhibitors of copper enzymes and of the alternative cyanide-resistant respiration did not significantly alter resistance induction by Myco. When Myco-treated plants were subjected to a moderate water stress and inoculated with nematodes, they retained numbers of developed individuals in the roots similar to those present in regularly watered plants, in contrast to what occurred in roots of untreated stressed plants that hosted very few individuals because of poor nutrient availability.

Fungi of the genus Aspergillus are widespread in the environment where they produce large quantities of airborne conidia. Inhalation of Aspergillus spp. conidia in immunocompromised individuals can cause a wide spectrum of diseases, ranging from hypersensitivity responses to lethal invasive infections. Upon deposition in the lung epithelial surface, conidia encounter and interact with complex microbial communities that constitute the lung microbiota. The lung microbiota has been suggested to influence the establishment and growth of Aspergillus spp. in the human airways. However, the mechanisms underlying this interaction have not yet been sufficiently investigated. In this study, we aimed to evaluate the presence of commensal bacteria antagonistic to Aspergillus in the lung. To this end, we enriched and isolated bacterial strains able to inhibit the germination of conidia from bronchoalveolar lavage fluid (BALF) samples of lung transplant recipients. We used a novel enrichment method based on a soft agar overlay plate assay in which bacteria are directly in contact with conidia and for which inhibition can be readily observed during enrichment. We isolated a total of five bacterial strains, identified as Pseudomonas aeruginosa, and able to inhibit the germination and growth of Aspergillus fumigatus in a soft agar confrontation assay, as well as in a high-throughput multiplate assay. Moreover, we also showed a strong inhibition of A. fumigatus growth on Calu-3 cell culture monolayers. However, the isolated P. aeruginosa strains were shown to cause significant damage to the cell monolayers. Overall, we validated this novel one-step enrichment approach for the isolation of bacterial strains antagonistic to A. fumigatus from BALF samples. This opens up a new venue for targeted enrichment of antagonistic bacterial strains against specific fungal pathogens.

Background: Cutaneous Melanoma (SKCM) is characterized by significant heterogeneity in its molecular, genomic, and immunologic characteristics. Methods: Whole transcriptome RNAseq data from The Cancer Genome Atlas of SKCM (n=328) was utilized. The immune microenvironment was characterized using CIBERSORTX to identify immune cell type composition. Unsupervised hierarchical clustering was performed based on immune cell type content. Samples were separated into those obtained from the primary tumor site and regional skin or soft tissue (locoregional), or distant metastasis and regional lymph node (metastatic). Analysis of overall survival (OS) was performed using Kaplan-Meier estimates and Cox-regression multivariable analyses. Results: Four immune clusters were identified, largely defined by lymphocyte:monocyte (L:M) ratio, monocyte-enrichment, and M0-macrophage-enrichment (L:MLow, MonocyteHigh, M0High; L:MLow, MonocyteMid, M0Low; L:MMid, MonocyteLow, M0Low; L:MHigh, MonocyteLow, M0Low). The L:MLow, MonocyteHigh, M0High cluster demonstrated significantly worse OS than clusters 2-4 in the locoregional group (HR 2.804, 95% CI 1.262–6.234, p=0.0114). Membership in the L:MLow, MonocyteHigh, M0High cluster was an independently poor prognostic factor for survival (HR 3.03, 95% CI 1.12–8.20, p=0.029). The L:MLow, MonocyteHigh, M0High cluster correlated with higher rates of metastasis and decreased predicted response to immune checkpoint blockade compared to the other clusters as determined by the Tumor Immune Dysfunction and Exclusion tool (TIDE). Conclusion: Distinct tumor immune clusters with a M0-macrophage-enriched, L:M ratio low phenotype in the primary melanoma tumor site independently characterize an aggressive phenotype that may differentially respond to treatment.

(1) Background: The diagnosis of lumbosacral radiculopathy involves anamnesis, assessment of sensitivity and strength, diagnostic imaging—usually magnetic resonance imaging (MRI)—and electrodiagnostic testing (EDX), typically electromyography (EMG) and electroneurography (ENG). MRI evaluates the structures supporting the spinal cord, while EDX evaluates root functionality. The present study aimed to analyze the concordance of MRI and EDX findings in patients with clinically suspected radiculopathy. Additionally, we investigated the comparison between these two reference tests and various clinical variables and questionnaires. (2) Methods: We designed a prospective epidemiological study of consecutive cases with an observational, descriptive, cross-sectional, and double-blind nature following the STROBE guidelines, encompassing 142 patients with clinical suspicion of lumbosacral radiculopathy. (3) Results: Of the sample, 58.5% tested positive for radiculopathy using EDX as the reference test, while 45.8% tested positive using MRI. The comparison between MRI and EDX in the diagnosis of radiculopathy in patients with clinical suspicion was not significant; the overall agreement was 40.8%. Only the years with symptoms were comparatively significant between the positive and negative radiculopathy groups as determined by EDX. (4) Conclusion: The comparison between lumbar radiculopathy diagnoses in patients with clinically suspected pathology using MRI and EDX as diagnostic modalities did not yield statistically significant findings. MRI and EDX are complementary tests assessing different aspects in patients with suspected radiculopathy; degeneration of the structures supporting the spinal cord does not necessarily imply root dysfunction.

In this paper, we introduce new formulas for calculating the restoring and repulsive magnetic forces between two non-coaxial circular loops with parallel axes. These formulas are derived from a modified version of Grover’s formula for mutual inductance between the coils in question. Utilizing these formulas, we compute the restoring and repulsive magnetic forces between two non-coaxial thick coils of rectangular cross-sections with parallel axes. In these calculations, we apply the filament method and conduct investigations to determine the optimal number of subdivisions for the coils in terms of computational time and accuracy. The method presented in this paper is also applicable to all conventional non-coaxial coils, such as disks, solenoids, and non-conventional coils like Bitter coils, all with parallel axes. This paper emphasizes the accuracy and computational efficiency of the calculations. Furthermore, the new method is validated according to several previously established methods

Magnetic sensors are widely used in health management systems for turbomachinery, but their applications in the hot zone are limited due to the loss of magnetic properties by permanent magnets with increasing temperature. The paper presents and verifies models and design solutions aimed at improving the performance of an inductive sensor for measuring the motion of rotating objects operating at elevated temperatures (200-1000C), such as compressor and turbine blades. Physical, analog and mathematical models of the interaction of blades with the sensor were developed. A prototype of the sensor was made and its tests were carried out on the RK-4 rotor rig for the speed of 7000 rpm, in which the temperature of the sensor head was gradually increased to 1100C. The sensor signal level was compared to that of an identical sensor operating at room temperature. The heated sensor works continuously producing the output signal whose level does not change significantly. What is more, a set of six probes passed an initial engine test in an SO-3 turbojet. It was confirmed that the proposed design of the inductive sensor is suitable for blade health monitoring of the last stages of compressors, steam turbines as well as previous generation gas turbines operating below 1000C, even without a dedicated cooling system. In real-engine applications, sensor performance will depend on how the sensor is installed and the available heat dissipation capability

To clarify the relationships among critical temperature, critical magnetic field, and critical current density, this paper describes many-body interactions of quantum magnetic fluxes (i.e., vortices) and calculates pinning-related critical current density. All calculations are analytically derived, without numerical or fitting methods. Afteralculating a magnetic flux quantum mass, we theoretically obtain the critical temperature in a many-body interaction scenario (which can be handled by our established method). We also derive the critical magnetic field and inherent critical current density at each critical temperature. Finally, we determine the pinning-related critical current density with self-fields. The relationships between the critical magnetic field and critical temperature, inherent critical current density and critical temperature, and pinning critical current density and temperature were consistent with experimental observations. From the critical current density and critical magnetic field, we clarified the magnetic field transition. It appears that a magnetic flux quantum collapses when the lattice of magnetic flux quanta melts. Our results, combined with our previously published papers, provide a comprehensive understanding of the transition points in high-T_c cuprates.

Magneto-electrochemistry (MEC) is a unique paradigm in science, where electrochemical experiments are carried out as a function of an applied magnetic field, creating a new horizon of potential scientific and technological applications. Over the time, detailed understanding of this research domain was developed to identify and rationalize the possible effects exerted by a magnetic field on the various microscopic processes occurring in an electrochemical system, such as: electrolyte properties governed by charge-transfer process (electric conductivity, viscosity, and diffusivity), mass transfer, electrochemical kinetics and on the structure/quality of products formed either at the working electrode or in the electrochemical cell. Particularly, magnetic field controlled chiral architecture obtained from deposited metal, alloys and catalyst and their excellent enantio-recognition in experimental frame is highly appealing. Interestingly, Hall effect was also demonstrated in electrolytic medium via an impressive experimental technique which is being employed for further theoretical understanding in the field of magneto-electrochemical science. Later, a highly reproducible local temperature variation was observed in electrochemical electrolytes exposed to perpendicular magnetic and electric fields. However, until recent studies, none of the above mentioned reports considered the possibility of a spin-dependent related charge-transfer process. Recent experimental and theoretical studies reveal that electron’s transmission through chiral molecules is spin-selective and this effect has been referred to as chiral-induced spin-selectivity (CISS) effect. The CISS effect pave the way for the building up of a system characterized by a net magnetic moment exploiting the spin-filtering ability of chiral molecules. This interplay between chirality and magnetism may shed light on fundamental scientific aspects underlying the enantio-recognition and highly efficient electron-transfer that occurs in biological process.

We believe that a natural focus of the Physics Education Research community is on understanding and improving student learning in our physics courses. For this purpose, we are introducing smartphones in the physics laboratory. Current smartphones measure each component of the magnetic field, bearing in mind that any current perpendicular to a magnetic field produces a small potential difference, transversal to the said current, being this voltage easily measurable by Hall sensors. In this work, we have considered the magnetic field created by a linear quadrupole and we have studied its dependence on distance. Using an experimental procedure that is simple we have measured the magnetic field using the Hall sensor that most smartphones have, together with the corresponding app. The purpose of this work is to show that the laboratory is a powerful tool that increases significant learning under three conditions: 1) the practice must not be too sophisticated; 2) students must handle objects in the lab; and 3) the practice must be scientifically accurate, including the adjustments by minimum squares, and the following and necessary error calculation.

The Great Barrier Reef (GBR) is currently experiencing widespread crown of thorns starfish (CoTS) outbreaks as part of the fourth wave of outbreaks since 1962. It is believed that outbreaks have become more frequent on the GBR and elsewhere in the Indo-Pacific associated with anthropogenic causes. The two widely accepted potential causes are (1) anthropogenic nutrient enrichment leading to increased biomass of phytoplankton, the food of the planktonic stage of larval CoTS; and (2) overfishing of predators on the juvenile to adult stages of CoTS, for example, commercial fished species such as coral trout. In this study, we show the evidence for the nutrient enrichment causation hypothesis is strong based on a large number of recent studies in the GBR. We also hypothesise that secondary outbreaks in the region between Cairns and Townsville can also be enhanced by nutrient enriched conditions associated with the annual nutrient discharge from Wet Tropics rivers.

Gene expression profiling data contains more information than is routinely extracted with standard approaches. Here we present Fold-change-Specific Enrichment Analysis (FSEA), a new method for functional annotation of differentially expressed genes from transcriptome data with respect to their fold changes. FSEA identifies GO terms, which are shared by the group of genes with a similar magnitude of response, and assesses these changes. GO terms found by FSEA are fold-change-specifically (e.g. weakly, moderately or strongly) affected by a stimulus under investigation. We demonstrate that many responses to abiotic factors, mutations, treatments and diseases occur in a fold-change-specific manner. FSEA analyses suggest that there are two prevailing responses of functionally-related gene groups, either weak or strong. Notably, some of the fold-change-specific GO terms are invisible by classical algorithms for functional gene enrichment, SEA and GSEA. These are GO terms not enriched compared to the genome background but strictly regulated by a factor within specific fold-change intervals. FSEA analysis of a cancer-related transcriptome suggested that the gene groups with a tightly coordinated response can be the valuable source to search for possible regulators, markers and therapeutic targets in oncogenic processes. Availability and Implementation: FSEA is implemented as the FoldGO Bioconductor R package and a web-server https://webfsgor.sysbio.cytogen.ru/ .

This article theoretically derives the magnetic field and vector potential produced by a steady current I flowing in an arbitrary plane loop at an arbitrary point r. Numerical examples are presented to demonstrate the behavior of the magnetic field produced by loops of various shapes such as polygons, circles, ellipses, and p-norm balls. Taking the limit as the loop shrinks to a point and the current I grows to infinity so that the magnetic dipole moment m of the loop (defined as the current I times the vector area of the loop) is kept constant, the magnetic field and vector potential are theoretically shown to converge to those of an ideal point magnetic dipole m.

Applications in security and electronic surveillance require combination of excellent magnetic softness with good mechanical and anti-corrosive properties and low dimensionality. We overviewed the properties of soft magnetic glass-coated microwires and different post-processing making them quite attractive for electronic article surveillance and security applications. We studied the magnetostatic interaction between the microwires and routes to tune the non-linear hysteresis loops by using the arrays of different types of amorphous microwires. The presence of neighbouring microwire (either Fe or Co-based) significantly affects the hysteresis loop of the whole microwires array. In a microwires array containing magnetically bistable microwires we observed splitting of the initially rectangular hysteresis loop with a number of Barkhausen jumps correlated with the number of magnetically bistable microwires. Essentially, non-linear and irregular hysteresis loops have been observed in mixed arrays containing Fe and Co-rich microwires. The observed non-linearity in hysteresis loops allowed to increase the harmonics and tune their magnetic field dependencies. Non-linear hysteresis loops have been also observed upon devitrification of amorphous microwires. On the other hand, several routes allowing to tune the switching field by either post-processing or modifying the magnetoelastic anisotropy have been reviewed. Observed unique combination of magnetic properties together with thin dimensions and excellent mechanical and anti-corrosive properties provide excellent perspectives for the use of glass-coated microwires for security and electronic surveillance applications.

This study used established biomarkers of death due to ischemic stroke (IS) and performed network, enrichment, and annotation analysis. Protein-protein interaction (PPI) network analysis revealed that the backbone of the highly connective network of IS death consisted of IL6, ALB, TNF, SERPINE1, VWF, VCAM1, TGFB1, and SELE. Cluster analysis revealed immune and hemostasis subnetworks, which were strongly interconnected through the major switches ALB and VWF. Enrichment analysis revealed that the PPI immune subnetwork of death due to IS was highly associated with TLR2/4, TNF, JAK-STAT, NOD, IL10, IL13, IL4, and TGF-β1/SMAD pathways. The top biological and molecular functions and pathways enriched in the hemostasis network of death due IS were platelet degranulation and activation, the intrinsic pathway of fibrin clot formation, the urokinase-type plasminogen activator pathway, post-translational protein phosphorylation, integrin cell surface interactions, and the proteoglycan-integrin-extra cellular matrix complex (ECM). Regulation Explorer analysis of transcriptional factors shows: a) that NFKB1, RELA and SP1 were the major regulating actors of the PPI network; and b) hsa-mir-26-5p and hsa-16-5p were the major regulating microRNA actors. In conclusion, prevention of death due to IS should consider that current IS treatments may be improved by targeting VWF, VEGFA, proteoglycan-integrin-ECM complex, NFKB/RELA and SP1.

Angiotensin converting enzyme 2 (ACE2) is a key entry point of SARS-CoV-2 virus known to induce COVID-19. We have recently outlined the concept to reduce ACE2 expression by the administration of glycyrrhizin, a component of Glycyrrhiza glabra extract, via its inhibitory activity on 11beta hydroxysteroid dehydrogenase type 2 (11betaHSD2) and resulting activation of mineralocorticoid receptor (MR). We hypothesized that in organs, such as the intestine, which co-express 11betaHSD2, MR and ACE2, the expression of ACE2 would be suppressed. We studied organ tissues from an experiment originally designed to address the effects of Glycyrrhiza glabra extract on the stress response. Male Sprague Dawley rats were left undisturbed or exposed to chronic mild stress for five weeks. For the last two weeks, animals continued with a placebo diet or received a diet containing extract of Glycyrrhiza glabra root at a dose of 150 mg/kg of body weight/day. Quantitative PCR measurements showed a significant decrease in gene expression of ACE2 in the small intestine of rats fed with diet containing Glycyrrhiza glabra extract. This effect was independent of the stress condition and failed to be observed in non-target tissues, namely the heart and the brain cortex. In the small intestine we confirmed the reduction of ACE2 also at the protein level. Present findings provide first evidence to support the hypothesis that Glycyrrhiza glabra extract may reduce an entry point of SARS-CoV-2. Whether this phenomenon, when confirmed in additional studies, is linked to the susceptibility of cells to the virus requires further studies.

The COVID-19 global pandemic has created dire consequences with an alarming rate of morbidity and mortality. There are not yet vaccine or efficacious treatment options to combat the causative SARS-CoV-2 infection. This paper describes the identification of potentially repurposable drugs for COVID-19 treatment by conducting pathway enrichment analysis on publicly available Gene Expression Omnibus datasets. We first determined SARS-CoV-2 infection-induced alterations of host gene expressions and pathways. We then identified drugs or compounds that target and counter virus-triggered cellular perturbations, suggesting their potential repurposing for COVID-19 treatment. The key findings are that SARS-CoV-2 infection in host cells induces mitochondrial dysfunction, inhibits oxidative phosphorylation, and activates several immune response and pro-inflammatory pathways. Triptolide, the major bioactive component of a traditional Chinese medicine herb, may rescue mitochondrial dysfunction by activating oxidative phosphorylation. Further in vitro and in vivo studies are necessary to verify these results prior to clinical application.

Nymphaea lotus L. is the medicinal plant that has long been used as food, cosmetic and traditional medicines in Africa and Asia since the ancient time. Its flavonoids and other interesting phytochemical compounds from rhizome, leaf, and the whole flowers have been reported in the previous published researches. However, stamens, which are essential for reproductive functions, may also represent new alternative sources of potential antioxidant flavonoids as investigated in this study. The innovative green chemistry method i.e. ultrasound-assisted extraction (USAE) as well as macroporous resin (MPR) purification procedure were employed in this current research. The optimal ultrasound-assisted extraction condition is 90 % (v/v) aqEtOH with 34.65 khz ultrasonic frequency and 46 minutes of extraction time. Comparing with heat reflux extraction (HRE) conventional method, the significant gain of 1.35 total flavonoids content was obtained using optimized USAE conditions, jumping to 2.80 when this USAE associated with MPR purification. Not only in vitro cell free antioxidant activity of N. lotus stamen extracts, but also in cellulo antioxidant investigation using yeast model showed the same trend to indicate that the best antioxidant flavonoid can be found in USAE coupled with MPR purification. Moreover, the key antioxidant genes expression in yeast model such as SIR2 and SOD2 were also expressed at the highest level in yeast cell treated with the extract from USAE together with MPR purification. Consequently, it can be seen that the USAE combined with MPR purification can help to enhance the flavonoids antioxidant potential of the stamens extract from this medicinal species.

In this study, four kinds of animal bone marrow powders were extracted with n-hexane using the Soxhlet extraction method. Polyunsaturated fatty acids were enriched by urea inclusion and low temperature crystallization method, then were further evaluated antioxidant and antibacterial activities. These results showed that the oil composition of the n-hexane extracts of four kinds of animal bone marrow primarily consisted of palmitic acid (18.57–31.01%), stearic acid (3.6–20.95%), and oleic acid (40.22–58.69%). The ratios of saturated fatty acids (SFA)/unsaturated fatty acids (UFA) were 1/1.417, 1/1.327, 1/2.140, and 1.285/1 for sheep, bovine, horse, and camel bone marrow oil, respectively. The SFA/UFA ratios determined by the urea inclusion method were 1/1.518, 1/1.390, 1/2.037, and 1.216/1, respectively. The SFA/UFA ratios according to the low temperature crystallization method with acetone were 1/1.920, 1/2.141, 1/2.360, and 1/1.157 for sheep, bovine, horse, and camel bone marrow oil, respectively. These enrichment methods effected the concentrations of UFAs from the camel bone marrow oil. Among the methods, the low temperature crystallization method effectively enriched the UFAs. All four bone marrow oils exhibited strong antioxidant and antimicrobial activities. The horse bone marrow oil showed the strongest antioxidant activity. Both antioxidant and antimicrobial activity improved after enrichment of the UFAs. These results lay a theoretical basis for application bone marrow oil resources in food and medicine.

Fast Field-Cycling (FFC) Nuclear Magnetic Resonance (NMR) relaxometry is a powerful non-destructive magnetic resonance technique that enables, among other things, the investigation of slow molecular dynamics at low magnetic field intensities. FFC-NMR relaxometry measurements provide insight into molecular motion across various timescales within a single experiment. This study focuses on a \textit{model-free} approach, representing the NMRD profile $R_1$ as a linear combination of Lorentzian functions, thereby addressing the challenges of fitting data within an ill-conditioned linear least-squares framework. Tackling this problem, we present a comprehensive review and experimental validation of three regularization approaches to implement the model-free approach to analysing NMRD profiles. These include: (1) \nameUpe, utilizing locally adapted $L_2$ regularization; (2) \nameL, based on $L_1$ penalties; and (3) a hybrid approach combining locally adapted $L_2$ and global $L_1$ penalties. Each method's regularization parameters are determined automatically, according to the Balancing and Uniform Penalty principles. % Our contributions include the implementation and experimental validation of the \nameUpe{} and \nameUp{} algorithms, and the development of a "dispersion analysis" technique to assess the existence range of the estimated parameters. The objective of this work is to delineate the variance in fit quality and correlation time distribution yielded by each algorithm, thus broadening the set of software tools for the analysis of sample structures in FFC-NMR studies. The findings underline the efficacy and applicability of these algorithms in the analysis of NMRD profiles from samples representing different potential scenarios. 1

The aim of study was to investigate epidemiology aspects of magnetic resonance imaging (MRI) during COVID-19 pandemic. The study comprised depersonalized residents of Tomsk and Tomsk Region (n = 1714). Invitations to take online survey were sent to 50,000 residents by target SMS with response rate of 1.2% (n = 727, Cohort 1). Cohort 2 comprised retrospective patients (n = 987) who underwent contrast-enhanced cardiac MRI (CMR) in 2019-2022. Referrals, clinical characteristics, diagnosis, gender, age, past COVID-19, MRI study protocols, and MRI data were analyzed. 29% of respondents in cohort 1 received MRI examination within past two years; 26% of respondents considered MRI the most informative imaging modality for detecting COVID-19 pneumonia; 12% of respondents reported MRI unavailable. Proportion of CMR among MRI studies increased during COVID-19 pandemic, and maximum incidence of cardiac diseases detected by MRI was in 2021. Incidence of myocardial fibrosis increased from ~67% in 2019 to ~84% in 2022. The rate of outpatient MRI studies significantly increased in 2020, but returned to pre-pandemic level in 2021. COVID-19 pandemic increased the need for MRI and CMR. Patients with history of COVID-19 had persistent and newly occurring symptoms of myocardial damage suggesting chronic cardiac involvement requiring continuous follow-up.

Several eye-tracking technologies have been developed in the last 20 years. This paper aims to present a new kind of eye tracker that can produce detailed information on both eye and head movements using an array of magnetoresistive detectors fixed on the patient’s head and a small magnet inserted in a contact lens, tailored to the subject’s cornea curvature. The software used for data analysis can combine or compare the eye and the head movements and can draw them up as 2D or 3D images. Preliminary data concern a starter patient that was asked to perform several tasks to establish the accuracy, reliability and tolerance of the magnetic eye tracker and the software. The tasks included the evaluation of saccadic eye movements and pursuit, “drawing” shapes or alphabetical letters and reading. Finally, a Head Impulse Test (HIT) was performed for VOR gain estimation, comparing the standard deviation established through vHIT to the one established through this magnetic eye tracker (mHIT). This prototypic device is low invasive, light, relatively low cost and tolerable, with a high grade of reliability and accuracy. All these features might lead to future use of the magnetic eye tracker in neurological and otoneurological fields.

Recently, cobalt iron boron (CoFeB) thin films have been widely investigated to apply to magnetic sensors, due to their high magnetic moment, anisotropy, and stability. However, most of these studies are conducted on rigid silicon substrates. For more diverse applications of magnetic sensors and angle sensors, it is important to explore the properties of ferromagnetic thin films grown on non-rigid deformable substrates. Here, using representative deformable substrates such as polyimide (PI), polyethylene naphthalate (PEN) and polydimethylsiloxane (PDMS) that can be bent or stretched, we report experimental comparison of in-plane magnetic field angle-dependent properties of the amorphous Ta/CoFeB/MgO/Ta thin film which is grown on those deformable substrates. We investigate effects of substrate roughness, tensile stress, characteristics of deformable substrates, and sputtering process on the change of magnetic properties like coercive field (Hc), remanence over saturation magnetization (Mr/Ms), and their biaxial characteristics. This work presents unconventional foundations for exploring deformable magnetic sensors capable of detecting magnetic field angle.

One-Dimensional Solar Cell Capacitance Simulator (1D-SCAPS) and n-i-p planar configuration have been employed for the simulation of the caesium tin iodide (CsSnI₃)-based perovskite solar cell (PSC) with titanium (IV) oxide (TiO₂) and copper thiocyanate (CuSCN) as the electron and hole transport materials respectively. The results obtained for the initially modeled PSC compared well with similar devices in the literature but marred with high recombination rate. As such, the defect density in the CsSnI₃ absorber was varied from 10¹³ cm^-3 to 10¹⁷ cm^-3 and enriched with SnCl₂ (additive) and Br⁻(dopant) respectively. This strategy ensured a reduced concentration of Sn⁴⁺ vacancy (V_Sn) in the CsSnI₃ absorber with improved carrier lifetime and diffusion length beyond 0.05 ns and 1.1µm by a magnitude of the order of 10³ and 10² respectively for the enriched CsSnI₃ –based PSC. For the optimized PSC, we recorded V_OC=1.289 V, J_SC=32.60 mA.cm^-2, FF=83.56% and PCE=35.12%.

In this paper, a sensitivity sensor of dual-core photonic crystal fiber (DC-PCF) filled with magnetic liquid is introduced and investigated by the finite element method (FEM). To regulate the energy coupling involving the two cores, the magnetic fluid is filled into the pore between the two cores. To adjust the coupling between the supermodes in the DC-PCF, the refractive index of the magnetic fluid-filled air hole may change due to the external magnetic field. This specifically created a magnetic fluid-filled DC-PCF, the magnetic fluid-filled hole is not used as the core for energy transmission, thus avoiding transmission loss. The dip wavelength and the magnetic field displayed an excellent linear connection between 80 and 260 Oe, depending on the numerical data. The detection sensitivity of the magnetic field reached 515.75 pm/Oe at a short fiber length of 482 m. The designed magnetic fluid-filled DC-PCF has high sensitivity and small volume and has great application prospects in medical and industrial field magnetic field detection.

Temperature dependent entropic force acting between the straight direct current I and the linear system (string with length of L) of N elementary non-interacting magnets/spins μ is reported. The system of elementary magnets is supposed to be in the thermal equilibrium with the infinite thermal bath T. The entropic force at large distance from the current is given by Fmagnen=Nμ02μ2I24π2kBTr3 , where r is the distance between the edge of the string and the current I, and kB is the Boltzmann constant; (r≫L is adopted). The entropic magnetic force is the repulsion force. The entropic magnetic force scales as Fmagnen~1T , which is unusual for entropic forces. The effect of “entropic pressure” is predicted for the situation when the source of the magnetic field is embedded into the continuous media, comprising elementary magnets/spins.

Objective. To test the hypothesis that a session of unilateral tSMS over the dominant primary motor cortex (M1) in healthy subjects produces a transient decrease in manual dexterity. Methods. A triple-blinded randomized control trial was conducted in 40 healthy participants who were allocated to real- or sham-tSMS group. Each participant underwent one session of tSMS and were assessed before, immediately after, 15 minutes, and 40 minutes after stimulation. Outcome measures were Finger Tapping Test (FTT), 5-seconds FTT, nine Hole Peg Test, and the hand grip assessment. Results: Significant differences were found between groups 15 minutes after stimulation in favor of the tSMS group in the FTT (2.2 ± 0.99; CI= .18-4.22; d= .84p=.034), and 5-second FTT (4.2 ± 1.98; CI= .199-8.2, d= .68; p=.04). In the intragroup analysis, a significantly lower number of taps 15 minutes after stimulation was observed in sham group (3.3 ± 1.01; CI= .47-6.13; d= .42; p=.015), but not in the real stimulation group. Conclusion: A unilateral session of tSMS in the M1 of the dominant hemisphere of healthy individuals does not reduce manual dexterity or grip strength. This technique could have benefits on the motor performance of the arm contralateral to the stimulated motor cortex

Florida geologic units and soils contain a wide range in concentrations of naturally-occurring arsenic. The average range of bulk rock concentrations is 1 to 13.1 mg/kg with concentrations in accessary minerals being over 1,000 mg/kg. Soils contain natural arsenic concentrations of between 0.18 and 2.06 mg/kg with organic-rich soils having the highest concentrations. Anthropogenic sources of arsenic have added about 610,000 metric tons of arsenic into the Florida environment since 1970, thereby increasing background concentrations in soils. The anthropogenic sources of arsenic in soils include: pesticides (used in Florida beginning in the 1890’s), fertilizers, chromated copper arsenate (CCA)-treated wood, soil amendments, cattle-dipping vats, chicken litter, sludges from water treatment plants, and others. The default Soil Cleanup Target Level (SCTL) in Florida for arsenic in residential soils is 2.1 mg/kg which is below some naturally-occurring background concentrations in soils and anthropogenic concentrations in agricultural soils. A review of risk considerations shows that adverse health impacts associated with exposure to arsenic is dependent on many factors and that the Florida cleanup levels are very conservative. Exposure to arsenic in soils at concentrations that exceed the Florida residential cleanup level in residential environments does not necessarily pose a meaningful public health risk.

The article presents a technology for producing nitrogen-containing nanoporous biocarbon with high degree of elemental composition homogeneity, confirmed by electron spectroscopy. The research explores the relationship among the electronic characteristics of supramolecular nanoporous carbon, its porous structure, and the capacitance at its interface with the electrolyte. The obtained biocarbon is characterized by micro and mesopores, as evidenced by the results of studies by the method of nitrogen adsorption/desorption. The specific area of the available porous surface was found to be 1247 m2/g. Comparing this result with the data of small-angle X-ray scattering, we conclude that micropores are open while mesopores remain closed. This material was found to have a saturation magnetization σs of 1.4 A∙m2∙kg-1 and a coercive force Hc of 10 kA/m. The impedance studies of electrochemical cells of supercapacitors made of the experimental biocarbon were carried out. Equivalent electrical circuits of the studied electrochemical processes were constructed and characterized.

The study was performed to get the first insight of distribution of the low field volume magnetic susceptibility (MS) throughout the Zagreb city area, based on in-situ field measurements. Most interesting locations were selected for soil sampling and geochemical content was determined using ICP-OES. A geostatistical approach was applied on MS and geochemical results. Median value of 0.245 x 10-3 SI units is proposed to be used as relevant average MS value in Zagreb area. Mean concentrations of heavy metals in Zagreb soils (in µg/g) are: Pb (36.82), Zn (87.77), Cu (30.84), Cd (0.66), Cr (29.04), Co (11.89) and Ni (28.40), being relatively low in comparison with Croatian legislation and with European and world average. Boxplot analyses showed that 45% of studied elements do not show any anomaly, while the rest of elements mostly show only one weak anomaly and they are located at the same sites as MS anomalies. Statistical analysis found significant correlations between MS and following elements: Cd, Co, Fe, Mn, Na, Pb, Sb and Zn. In-situ MS measurements proved to be an efficient tool for initial screening of large areas in terms of elevated heavy elements concentrations, enabling cheap and fast assessment of state of environment.

To harness light-matter interaction at nano-/micro-scale better control tools have to be developed. Here, it is shown that by applying external electric and/or magnetic field, ablation of Si and glass under ultra-short (sub-1~ps) laser pulse irradiation can be controlled via the Lorentz force $\mathbf{F} = e\mathbf{E} + e[\mathbf{v}\times\mathbf{B}]$, where $\mathbf{v}$ is velocity of charge $e$, $\mathbf{E}$ is the applied electrical bias and $\mathbf{B}$ is the magnetic flux density. The external electric E-field was applied during laser ablation using suspended micro-electrodes above glass substrate with an air gap for the incident laser beam. The counter-facing Al-electrodes on Si surface were used to study debris formation patterns on Si. Debris was deposited preferentially towards the negative electrode in the case of glass and Si ablation. Also, an external magnetic field was applied during laser ablation of Si in different geometries and is shown to affect ripple formation. The vectorial nature of the Lorentz force widens application potential of surface modifications and debris formation in external E-/B-fields with potential applications in mass and charge spectroscopes.

The principles of causality and unitarity are studied within rational nonlinear electrodynamics proposed earlier. We investigate dyonic and magnetized black holes and show that in the self-dual case, when the electric charge equals the magnetic charge, corrections to Coulomb's law and Reissner-Nordstrom solutions are absent. In the case of the magnetic black hole, the Hawking temperature, the heat capacity and the Helmholtz free energy are calculated. It is shown that there are second-order phase transitions and it was demonstrated that at some range of parameters the black holes are stable.

The aim of this study is to solve the problems of complicated pretreatment and high analytical cost in the detection technology of trace drug toxicants in municipal wastewater. A high-performance magnetic sorbent was synthesized for enrichment of trace drug substances in wastewater to develop magnetic solid-phase extraction pretreatment combined with the acoustic ejection mass spectrometry (AEMS) analytical methods for the molecules in wastewater drug toxicants. The magnetic nanospheres was successfully prepared by magnetic nanoparticles modified with divinylbenzene and vinyl pyrrolidone.The results showed that the linear dynamic range of 17 drugs was 1-500 ng/L, the recovery was 43%-105%, the matrix effect was more than 67%, the limit of quantitative detection was 1-2 ng/L, and the detection time of each sample was 2.98s. It can be seen that the developed magnetic solid-phase extraction (MSPE) method is a good solution to the problem of complicated pre-treatment and analytical cost in the detection of drugs in wastewater. The developed magnetic material and acoustic excitation coupled mass spectrometry analysis method can realize the low-cost, efficient enrichment and fast analysis of different kinds of drug molecules in urban sewage.

We studied the effect of annealing and the applied magnetic field from 50 Oe to 20 kOe on the magneto-structural behavior of Ni2FeSi-based Heusler microwires fabricated by using Taylor-Ulitovsky technique. Using the XRD analysis, a strong effect of annealing, manifested as the development of the crystallization process, was observed. The average grain size and crystalline phase content of annealed sample increase from 21.3 nm and 34 % to 32.8 nm and 79%, respectively, as-compared to the as-prepared one. In addition, upon annealing phase transforms into a monoclinic martensitic structure with modulation 10M were observed, which cannot be found in the as-prepared sample. Concerning the magnetic properties, both samples show ferromagnetic behavior below and above the room temperature, where the Curie temperature of Ni2FeSi is higher than room temperature. The induced secondary phases have a noticeable effect on the magnetic behavior of the annealed sample, where a high normalized saturation magnetization (NMs) and low normalized reduced remenance (Mr = M/M5K), compared to the as- prepared have been detected. Additionally, the coercivity of annealed sample shows one flipping point at 155 K where it behavior with temperature is changed. Meanwhile, the as-prepared sample show two flipped point at 205 K and 55 K. A mismatch between field cooling (FC) and field heating (FH) magnetization curves with temperature has been detected for annealed sample at low applied magnetic field. In addition the FC and FH curves shows different slopes with variation the temperature and the magnetic field. By increasing the external magnetic field higher than 200 Oe and up to 20 kOe a gradual changing in the magnetic behavior has been detected, where the mismatch and different slopes disappeared at applying magnetic field about 20 kOe. The difference in magnetic and structure behavior of Ni2FeSi microwires sample is discussed considering the effect of induced internal stresses by the presence of a glass coating and the recrystallization and stresses relaxation upon annealing.

Many advanced reactor concept designs rely on high-assay low-enriched uranium (HALEU) fuel, enriched up to approximately 19.75% 235U by weight. Efforts are underway by the US government to increase HALEU production in the United States to meet anticipated needs. However, very little data exists for validation of computational models that include HALEU, beyond a few fresh fuel benchmark specifications in the International Reactor Physics Experiment Evaluation Project. Nevertheless, there is other data with potential value available for developing into quality benchmarks for use in data and software validation efforts. This paper reviews the available evaluated HALEU fuel benchmarks and some of the potentially relevant benchmarks for fresh highly enriched uranium. It then introduces experimental data for HALEU fuel irradiated at Idaho National Laboratory, from relatively recent irradiation programs at the Advanced Test Reactor. Such data should be evaluated and, if valuable, collected into detailed benchmark specifications to meet the needs of HALEU-based reactor designers.

Cocaine addiction is a global health problem that causes substantial damage to the health of addicted individuals around the world. Dopamine synthesizing neurons in the brain play a vital role in the addiction to cocaine. But the underlying molecular mechanisms that help cocaine exert its addictive effect have not been very well understood. Bioinformatics can be a useful tool in the attempt to broaden our understanding in this area. In the present study, Gene Set Enrichment Analysis (GSEA) was carried out on the upregulated genes from a dataset of Dopamine synthesizing neurons of post-mortem human brain of cocaine addicts. As a result of this analysis, 3 miRNAs have been identified as having significant influence on transcription of the upregulated genes. These 3 miRNAs hold therapeutic potential for the treatment of cocaine addiction.

Nanocrystalline La_1-xNd_xFeO₃ powders with different concentrations of Nd³⁺ have been synthesized by modified Pechini method. Their structure was studied by X-ray powder diffraction (XRD). Further, La_1-xNd_xFeO₃ nanoceramics were prepared by high pressure sintering technique. The luminescence spectra of the powders were investigated as a function of concentration of active dopant to check the possible energy transfers observed due to Nd³⁺ concentration changes. The electrical and magnetic properties of the powders and ceramics were investigated to determine the effect of Nd³⁺ doping on the dielectric permittivity and magnetization in the wide frequency range.

In this paper we give the improved and new analytical and semi-analytical expression for calcu-lating the magnetic vector potential, magnetic field, magnetic force, mutual inductance, torque, and stiffness between two inclined current-carrying arc segments in air. The expressions are ob-tained either in the analytical form over the incomplete elliptic integrals of the first and the sec-ond time or by the single numerical integration of some elliptical integrals of the first and the second kind. The validity of the presented formulas is proved from the special cases when the inclined circular loops are treated. We mention that all formulas are obtain by the integral ap-proach except the stiffness which is found by the derivative of the magnetic force.

Laser ablation of silicon under an external applied magnetic field with different orientations was investigated in respect to the scanning direction and polarisation of the laser beam, by observation of the ablation patterns and debris deposition. Ultra-short ∼230 fs laser pulses of 1030 nm wavelengths were used in the single and multi-pulse irradiation modes. Ablation with an externally applied magnetic B-field (B ≈ 0.1 T) is shown to strongly affect debris formation. The mechanism of surface plasmon polariton (SPP) wave can explain the ablated periodic patterns observed with alignment along the magnetic field lines.

Current smartphones incorporate different types of sensors that allow us to know our spatial position, they give us information about pressure, speed, acceleration, time, acoustic level, and other different physical magnitudes. These smartphones measure each component of the magnetic field, bearing in mind that any current perpendicular to a magnetic field produces a small potential difference, transversal to the said current, being this voltage easily measurable by Hall sensors. With the implementation of three Hall sensors, and an appropriate app, we can measure the three components of the magnetic field vector, and with this we can obtain information and deduce properties of the physical systems considered. In this paper we are exploring the use of smartphones in a physics laboratory for freshman students. To do this, we have measured, using Hall sensors, the magnetic field created by a linear quadrature, and we have obtained, first of all, its dependence on the distance between the quadrupole and the magnetic sensor. The second purpose of this work is to show that the laboratory is a powerful tool that increases the significant learning of freshman students through advanced technological tools.

The spin magnetic moments and spin g factors (g_s = -2) of electron, muon and tau are explained based on the electric charges (EC) and lepton charges (LC) in terms of the three-dimensional quantized space model. The spin g factors of electron, muon and tau are g_s = -2 which is the sum of the EC g factor (g_EC = -1) and the LC g factor (g_LC = -1). The spin g factor (g_s = -2) of the electron is predicted by the Dirac’s equation. The orbit g factors of electron, muon and tau are g_L = g_EC = -1 from the EC g factor (g_EC = -1) without the contribution of the LC g factor (g_LC = -1). The spin g factors of the elementary fermions are calculated from the equation of g_s = g_EC + g_LC + g_CC where g_EC = EC/|EC|, g_LC = LC/|LC| and g_CC = CC/|CC|. For example, the spin g factors of the neutrinos and dark matters are g_s = -1. The spin g factors of the u and d quarks are g_s = 0 and g_s = -2, respectively. The g factor problem of neutrinos with the non-zero LC charges are solved by the LC Coulomb force of F_c(LC) ≈0. It is, for the first time, proposed that the binary motion (fluctuations) of the m_EC and m_LC masses for the electron, muon and tau leptons make the anomalous g factor. This binary motion could be originated from the virtual particle processes including the photons. Also, the weak force (beta) decay is closely related to the binary motion of the m_EC and m_LC for the electron, muon and tau leptons.

Appling the controlling relative permittivity and permeability in the equations for the gravitational-magnetic-electric field interaction, a very large variation of the gravitational acceleration of the Earth by electric/magnetic field could be arrived at. This conclusion may be supported by some of the experiments for the gravitational effect of superconductivity.

We report on the design and construction of a spin-flip Zeeman slower, quadrupole magnetic trap, and Feshbach fields for a new machine for ultra-cold Li-7. The small mass of the Li-7 atom, and the tight lattice spacing, will enable us to achieve a 100-fold increase in tuneling rates over comparable Rb-87 optical lattice emulator experiments. These improvements should enable to access new regimes in quantum magnetic phase transitions and spin dynamics.

We report the electronic, magnetic and transport properties of a prototypical antiferromagnetic (AFM) spintronic device. We chose Cr as the active layer because it is the only room-temperature AFM elemental metal. We sandwiched Cr between two non-magnetic metals (Pt or Au) with large spin-orbit coupling. We also inserted a buffer layer of insulating MgO to mimic the structure and finite resistivity of a real device. We found that, while spin-orbit has a negligible effect on the current flowing through the device, the MgO layer plays a crucial role. Its effect is to decouple the Cr magnetic moment from Pt (or Au) and to develop an overall spin magnetization. We have also calculated the spin-polarized ballistic conductance of the device within the Büttiker-Landauer framework, and we have found that for small applied bias our Pt/Cr/MgO/Pt device presents a spin polarization of the current amounting to ~25%.

We report on magnetic studies of inhomogeneous commercial and synthesized amorphous carbon (a-C) and a-C doped with sulfur (a-CS) powders which exhibit (i) peculiar magnetic behavior and (ii) traces of two superconducting (SC) phase ~ Tc=33 and at 65 K. (i) The temperature dependence of zero-field-cooled (ZFC) curves measured up to room temperature show a well distinguish elusive peaks around 50-80 K, their origin is not yet known. These peaks are totally washed-out in the second ZFC sweeps and in the FC branches as well. As a result, in the vicinity of the peaks, the FC curves lie below the ZFC peaks (FC<ZFC), a phenomenon which is rarely observed. These magnetic anomalies are intrinsic properties of a-C and a-CS materials (ii) SC was observed in three different a-C sources: (a) The commercial a-C powder contains 0.21% of sulfur and it is suggested that two different a-CS phases (at 33 and 65 K) are the origin of the two SC states observed. The compositions of these two phases are not yet unknown. The small SC volume fractions of the 33 K phase can be enhanced by a solid reaction with additional sulfur at 250 ºC. (b) The synthesized a-C powder (obtained from decomposition of sucrose) is not SC. However, when mixed with sulfur and heated at 400 ºC under a protective atmosphere, the a-CS powder obtained also show traces of a SC phase at TC= 42 K. (c)The same occurs in a-C thin films. The as-grown films are not SC but a SC phase at Tc = 34 K emerges after the films were reacted with sulfur at elevated temperatures. It is concluded therefore, that all SC phases observed are due to different unknown a-CS phases. Since the a-C and a-CS powders possess SC and magnetic states, we believe that these powders resemble the high TC curates and Fe-As based systems in which the SC and the magnetic states are closed related to each other.

The high radio frequency polarization imaging of non-thermal emission from active galactic nuclei (AGN) is a direct way to probe the magnetic field strength and structure in the immediate vicinity of supermassive black holes (SMBHs) and is crucial in testing the jet-launching scenario. To explore the the magnetic field configuration at the base of jets in blazars, we took advantage of the full polarization capabilities of the GMVA (Global Millimeter VLBI Array). With an angular resolution of ~50 micro-arcseconds at 86 GHz, one could reach scales down to ~900 Schwarzschild radii (for a 10^9 solar mass black hole). We present here the preliminary results of our study on the blazar BL Lac. Our results imply that on sub-mas scales the core and central jet of BL Lac is significantly polarized with two distinct regions of polarized intensity. We also noted a great morphological similarity between the 7mm/3mm VLBI images at very similar angular resolution.

In our previous published papers, considering 3 large atomic gravitational constants assumed to be associated with weak, strong and electromagnetic interactions, we have proposed the existence of a nuclear charge of magnitude, e_n=2.95e and developed a nuclear mass formula associated with strong and weak interactions having 4 simple terms and only one energy coefficient. Two important assumptions are, there exists a weak fermion of rest energy 585 GeV and strong coupling constant is the squared ratio of electromagnetic charge and nuclear charge. The aim of this paper is associated with understanding the mystery of quantum of magnetic flux, Planck’s quantum radiation constant and Reduced Planck’s constant. Proceeding further, quark charges, strong coupling constant, nuclear stability, nuclear binding energy, medium and heavy atomic X-ray levels and celestial magnetic moments can be understood in a unified approach. It may also be noted that, by considering integral nature of elementary particle masses, it seems possible to understand the discreteness of angular momentum. Considering our proposed e_n=2.95e=3e as a characteristic nuclear charge, it seems possible to understand the integral nature of quarks electromagnetic charge. With this idea, neutron, proton and pions decay can be understood very easily. In all the cases, up quark of charge (±2e) seems to play a crucial role with the internal transformation of down quark of charge (±e) and external observable elementary basic elementary particles. It needs further study at fundamental level.

Hybrid organic/inorganic conducting and magnetic composites of core–shell type have been prepared by in-situ coating of nickel microparticles with polypyrrole. Three series of syntheses have been made. In the first, pyrrole was oxidized with ammonium peroxydisulfate in water in the presence of various amounts of nickel and the composites contained up to 83 wt% of this metal. The similar syntheses in 0.1 M sulfuric acid followed. Finally, the composites with polypyrrole nanotubes were prepared in water in the presence of structure-guiding methyl orange dye. FTIR and Raman spectroscopies confirmed the formation of polypyrrole. The resistivity of composite powders of the order of tens to hundreds Ω cm was monitored as a function of pressure up to 10 MPa. The resistivity of composites slightly increased with increasing content of conducting nickel. This apparent paradox is explained by the coating of nickel particles, which prevents their contacts and generation of metallic conducting pathways. Electrical properties were practically independent of the way of composite preparation or nickel fraction and were controlled by polypyrrole phase. On the contrary, magnetic properties were determined exclusively by nickel content. The composites were used as a solid phase to prepare a magnetorheological fluid. The test showed better performance when compared with a different nickel system.

This paper describes how to construct a low-cost magnetic levitation system (MagLev). The MagLev has been intensively used in the engineering education, allowing instructors and students to learn through hands-on experiments essential concepts, such as electronics, electromagnetism, and control systems. Built from scratch, the proposed MagLev depends only on simple, low-cost components readily available on the market. In addition to showing how to construct the MagLev, this paper presents a semi-active control strategy which seems novel when applied in the MagLev. Experiments performed in the laboratory have compared the proposed control scheme with the classical PID control. The corresponding real-time experiments illustrate both the effectiveness of the approach and the potential of the MagLev for education.

Magnetic Resonance Imaging (MRI) is a powerful, non-invasive and nondestructive tool, capable of providing three-dimensional (3D) images of living organisms. The use of magnetic contrast agents has allowed clinical researchers and analysts to enormously increase the sensitivity and specificity of MRI since these substances change the intrinsic properties of the tissues within a living body, increasing the information present in the images. The advances in nanotechnology and materials science as well as the research of new magnetic effects have been the driving forces that propel the use of magnetic nanostructures as promising alternatives to the commercial contrast agents used in MRI. This review discusses the principles associated with the use of contrast agents in MRI as well as the most recent reports focused on nanostructured contrast agents. The potential applications of gadolinium (Gd) and manganese Mn-based nanomaterials and iron oxide nanoparticles in this imaging technique are discussed as well, from their magnetic behavior to the mainly used materials and nanoarchitectures. Then, it is also addressed the recent efforts made to develop new types of contrast agents based on synthetic antiferromagnetic and high-aspect ratio nanostructures. Furthermore, the application of these materials in theragnosis, either as contrast agents and controlled drug release, contrast agents and thermal therapy or contrast agents and radiosensitizers, is also presented.

Magnetic nanoparticles are met across many biological species ranging from magnetosensitive bacteria, fishes, bees, bats, rats, birds, to humans. They can be both of biogenetic origin and due to environmental contamination, being either in paramagnetic or ferromagnetic state. The energy of such naturally occurring single-domain magnetic nanoparticles can reach up to 10-20 room k_BT in the magnetic field of the Earth, which naturally led to supposition that they can serve as sensory elements in various animals. This work explores within a stochastic modeling framework a fascinating hypothesis of magnetosensitive ion channels with magnetic nanoparticles serving as sensory elements, especially, how realistic it is given a highly dissipative viscoelastic interior of living cells and typical sizes of nanoparticles possibly involved.

This study aimed to develop multifunctional nanoplatforms for both cancer imaging and therapy using superparamagnetic iron oxide nanoparticles (SPIONs). Two distinct synthetic methods, reduction-precipitation (MR/P) and co-precipitation at controlled pH (MpH), were explored, including the assessment of coating’s influence, namely dextran and gold, on their magnetic properties. These SPIONs were further functionalized with gadolinium to act as dual T1/T2 contrast agents for magnetic resonance imaging (MRI). Parameters such as size, stability, morphology, and magnetic behavior were evaluated by a detailed characterization analysis. To assess their efficacy in imaging and therapy, relaxivity and hyperthermia experiments were performed, respectively. The results revealed that both synthetic methods lead to SPIONs with similar average, 9 nm. Mössbauer spectroscopy indicated that samples obtained from MR/P consist of approximately 11-13% of Fe present in magnetite, while samples obtained from MpH have higher content, of 33%-45%. Despite coating and functionalization, all samples exhibited superparamagnetic behavior at room temperature. Hyperthermia experiments showed increased SAR values with higher magnetic field intensity and frequency. Moreover, the relaxivity studies suggested potential dual T1/T2 contrast agent capabilities for the coated SPpH-Dx-Au-Gd sample, thus demonstrating its potential in cancer diagnosis.

The magnetic properties of RCo3B2 compounds, with heavy rare earths, are investigated by using magnetic measurements and electronic structure calculations. The cobalt sublattice magnetizations are very small and antiparallel oriented to rare earths moments. Contributions of cobalt moments to the Curie constants were also shown. The cobalt magnetic behavior has been analyzed in spin fluctuations model. The presence of short-range order above the Curie temperatures in RCo3B2 compounds with R=Tb, Dy, and Ho has been attributed to reminiscent R5d-Co3d interactions.