We aimed to investigate the relationship between membrane material and development of membrane fouling in a membrane bioreactor (MBR) using membranes with different pore sizes and hydrophilicities. Batch filtration tests were performed using submerged single hollow fiber membrane ultrafiltration (UF) modules with different polymeric membrane materials including cellulose acetate (CA), polyethersulfone (PES), and polyvinylidene fluoride (PVDF) with activated sludge taken from a municipal wastewater treatment plant. The three UF hollow fiber membranes were prepared by a non-solvent-induced phase separation method and had similar water permeabilities and pore sizes. The results revealed that transmembrane pressure (TMP) increased more sharply for the hydrophobic PVDF membrane than for the hydrophilic CA membrane in batch filtration tests, even when membranes with similar permeabilities and pore sizes were used. PVDF hollow fiber membranes with smaller pores had greater fouling propensity than those with larger pores. In contrast, CA hollow fiber membranes showed good mitigation of membrane fouling regardless of pore size. The results obtained in this study suggest that the surface hydrophilicity and pore size of UF membranes clearly affect the fouling properties in MBR operation when using activated sludge.

Dynamic virtual testing by Hardware in the Loop (HIL) real time simulation systems is common to minimize physical tests to validate and verify control algorithms, logics and software, under normal and emergency conditions. The accurate but costly HIL models setup activities could have an extended use to simulate faulty conditions that are seldom observable in the real system, yet they must be detected in advance and recognized. Data driven diagnostic methods have reached a mature development, in various sectors, proving effective in early detecting slowly varying deviations from nominal patterns of signals, even without a priori knowledge of their nature and behavior. These methods rely on vast amount of data logged from real systems that are ever and ever richer of monitoring telemetries that are worth being exploited. However, due to the usually reliable and safe systems being managed, it is often difficult to collect enough data on anomalous situations to validate fault detection and isolation and limit false positives. HIL model-based simulations allow generating and observing operational domains or transients rarely observed in real operations. This allows identifying the signals that are most correlated to faults and that could be selected to setup data-based diagnostic models of parts or subsystems, which are more suitable than the whole HIL model for online diagnostics, as well as to identify the features and trends that are most symptomatic of anomalous conditions.

The multiphase motors due to their reliability find new areas of application in the industry and transportation. Developing of any system with multiphase motors at first requires elaborate model of the system, define control mode and controllers. The model of control system for the six-phase drive is based on its conventional d-q mathematical model and indirect field-oriented control. Simulink model of six-phase drive with indirect field-oriented control and simulated with two types PID and PID fuzzy controllers. The simulation results, reflecting step response and provided speed reference law as well as load application at constant speed, are presented and analyzed. Fuzzy controller with 49 rules is considered and applied. Six-phase electric drive with field-oriented control at well-tuned PID controller has good step response specifications: settling time 0.13 s at starting without load, step response has no overshoot, small about 1 % short time decrease of speed at load of 5 Nm application. The system employing PID fuzzy controller shows slightly better results in response to torque application: the decrease in speed 1 % is eliminated in shorter time. Simulation results indicate the robustness of both systems with six-phase drive to disturbance and provide high quality transient specifications at determined reference speed.

With continuous increase in integration of the semiconductor devices, the requirements on size accuracy and surface quality of the etched lead frame are higher. The etchant is a key factor on etching process and etched surface quality, while effects of the difference in etchants on microscopic etched surface morphology of the Cu alloy have not been directly studied. In this study, the aqua regia, acidic FeCl3 and CuCl2 solutions were used as etchants, and the CuCrSn alloy specimens with different microstructure were etched and characterized. The results show that the etching rate in aqua regia is high, and the grain orientation, grain boundary (GB) and dislocation have significant influence on the local etching rate. The preferential etching of some atomic planes forms steps between grains with different orientations, and the preferential etching around the GB and dislocation group forms grooves, resulting in high surface roughness. For etching of the FeCl3 and CuCl2 etchants, the steps and grooves become blurred, and almost invisible on the surface etched by the CuCl2 etchant, thus the surface roughness is much lower. The CuCrSn alloy surface etched by the aqua regia is clean, with little Cr-rich particles, while high density Cr-rich particles are remained on the surfaces etched with the FeCl3 and CuCl2 etchants. For the same kind of etchant, the ion concentration can affect the etching mechanism and etching surface morphology.

Bio-molecular reagents like antibodies required in experimental biology are expensive and their effectiveness, among other things, is critical to the success of the experiment. Although such resources are sometimes donated by one investigator to another through personal communication between the two, there is no previous study to our knowledge on the extent of such donations, nor a central platform that directs resource seekers to donors. In this paper, we describe, to our knowledge, a first attempt at building a web-portal titled Bio-Resource Exchange that attempts to bridge this gap between resource seekers and donors in the domain of experimental biology. Users on this portal can request for or donate antibodies, cell-lines and DNA Constructs. This resource could also serve as a crowd-sourced database of resources for experimental biology. Further, in order to index donations outside of our portal, we mined scientific articles to find instances of donations of antibodies and attempted to extract information about these donations at the finest granularity. Specifically, we extracted the name of the donor, his/her affiliation and the name of the antibody for every donation by parsing the acknowledgements sections of articles. To extract annotations at this level, we propose two approaches – a rule based algorithm and a bootstrapped relation learning algorithm. The algorithms extracted donor names, affiliations and antibody names with average accuracies of 57% and 62% respectively. We also created a dataset of 50 expert-annotated acknowledgements sections that will serve as a gold standard dataset to evaluate extraction algorithms in the future. Contact: [email protected], [email protected] Database URL: http://tonks.dbmi.pitt.edu/brx Supplementary information: Supplementary data are available at Database online.

The purpose of this paper is to explore the implementation of Retrieval-Augmented Gen- 14 eration (RAG) technology with open-source Large Language Models (LLMs). For this purpose, a 15 web-based application named PaSSER that integrates RAG with three models - Mistral:7b, 16 Llama2:7b: Orca2:7b, is developed. In its development various technologies are used, including 17 Blockchain for managing and storing assessment results of built-in testing modules. PaSSER em- 18 ploys a set of evaluation metrics for LLMs’ performance - METEOR, ROUGE, BLEU, Perplexity, 19 Cosine similarity, Pearson correlation, and F1 score. The specialized knowledge base is in the smart 20 agriculture domain. As an illustration, the paper presents results and analysis of two tests. First one 21 is assessing the performance of LLMs across different hardware configurations, the other is deter- 22 mining the model that delivers most accurate and contextually relevant responses within the RAG. 23 The paper also discusses the integration of blockchain technology with LLMs to manage and store 24 assessment results within a blockchain environment. The tests revealed that Mistral:7b demon- 25 strates the best results across most of the evaluated metrics. The discussion section comments on 26 technical and hardware considerations that affect the performance of LLMs. Future development 27 will focus in leveraging new larger pre-trained open-source LLMs, exploring different finetuning 28 approaches, and further integration with Blockchain and IPFS.

In this paper, we proposed the fusion of two projection based face recognition algorithms: local binary Patterns in DCT domain and singular value decomposition (SVD) characterized by its simplicity and efficiently. Standard databases ORL are used to test the experimental results which prove that proposed system achieves more accurate face recognition as compared to individual method.

Firefighters Protective Clothing consist of several layers of different properties and functions. The layers create barriers against dangerous outer factor. However, they are also barriers to transport of sweat produced by human organism. It causes that very often sweat in the form of vapor is not transferred effectively from the human organism through the FPC to environment. This leads to sweat condensation on the skin of the FPC user causing his discomfort. In order to ensure as good as possible physiological comfort of firefighter while firefighting and other rescue actions it is necessary to take into consideration the transport of condensed sweat in the multilayer textile set creating the FPC. In the presented work four variants of multilayer textile sets for the FPC have been tested in the aspect of liquid moisture transport. Measurement was performed by means of the Moisture Management Tester (MMT290) – innovative instrument manufactured by the SDL Atlas. Obtained results showed that the transfer of sweat in liquid form occurs only in the inner, next to skin layer of the multilayer sets for the FPC.

In the drive towards environmental restoration and sustainable energy solutions, effective utilization and management of agricultural crop residues are vital to mitigate greenhouse gas (GHG) emissions and waste accumulation. Converting biogenic wastes into biofuels and bioproducts has the potential to tackle the energy crisis and contribute to environmental remediation. In this investigation, teff husk, primarily generated in Ethiopia during teff production within the agro-industrial sector, is used as the feedstock for the slow pyrolysis process. In Ethiopia, it is estimated that over 1.75 million tons of teff husk are generated annually, with a significant portion being incinerated in the fields, resulting in substantial environmental pollution. This study focuses on assessing teff husk as a potential material for slow pyrolysis, a crucial stage in biochar production, to tap into its biochar-producing potential. To determine the composition of the biomass, the teff-husk was initially analyzed by thermogravimetry. The significant presence of fixed carbon indicates that teff husk is a viable candidate for pyrolytic conversion into biochar particles. The process of slow pyrolysis took place at three varied temperatures—specifically, at 400, 450, and 500 °C. Process parameters of slow pyrolysis such as reaction time, temperature, and heating rate were enhanced to obtain maximum biochar yields. The highest biochar yield of 43.4 wt% was recorded at optimized reaction time, temperature, and heating rate of 120 min, 400 °C, and 4.2 °C/min, respectively. Furthermore, biochar's physicochemical, SEM-EDX, FTIR, and TGA characterization were performed. The thermal stability and carbon content of biochar were found to rise at higher temperatures. Unlike fuel recovery, the results suggest that teff-husk can be used as a feedstock for biochar production.

This paper describes a system that is used to gather data from Smart Home sensors measuring energy consumption, analyze and predict future consumption by using machine learning algorithm for prediction. It focuses on the architecture of the system as well as the need for such system to exist in practice – why the consumption should be measured at all and how that measurement can be put to good use for achieving energy efficiency.

Populational aging is marked by chronic non-communicable diseases, such as metabolic syndrome (MetS). IL-10 and IL-1β are pleiotropic cytokines with multiple biological effects linked to metabolic disorders. This cross-sectional study assessed 193 participants' IL-10 and IL-1β serum levels regarding their role in developing MetS, clinical characteristics, and their IL1B rs1143627 and IL10 rs1800890 variants' genotype frequencies in a population over 60. IL-10 levels correlated weakly with HDL levels and fat mass and inversely with triglycerides, glucose, glycated hemoglobin, and estimated average blood glucose levels. IL-10 levels were also indirectly influenced by the patient's T2DM duration, lean mass amount, and bone mineral content. Participants with altered HDL, elevated serum glucose, raised HbA1c levels, or those over 80 had reduced serum IL-10 levels compared to those with normal levels or other age groups, respectively. Women also had higher serum IL-10 levels than men. Dissimilarity, IL-1β levels correlated directly only with the number of total leukocytes and segmented neutrophils, showing only significant variations with self-reported alcohol consumption. Our study also found that those with the IL10 AA genotype (lower IL-10 levels) had a significantly higher risk of developing MetS. These findings may help direct future research and more targeted therapeutic approaches in older adults.

In this paper, we present an experimental procedure to enhance the dimensional accuracy of fabrication via Stereolithography (SLA) of features at the micro-scale. Using a custom benchmark part, deviations in feature dimensions (micro-pores diameters and depths) were detected and measured by confocal microscopy. Samples characterization and experimental observations allowed the identification of inaccuracy sources, mainly due to the laser beam scanning strategy and to the incomplete removal of uncured liquid resin in post-processing (i.e., IPA washing). As a technology baseline, the measured dimensional errors on pores diameters were up to -46%. A compensation method of the nominal laser spot diameter (85m) was defined and implemented resulting in relevant improvements in dimensional accuracy of 9.8% and 11.3% on full-open pores diameter and depth, respectively. Further investigation was performed on a customized test part to adjust the calibration procedure. The measurements revealed that the estimate of the laser beam spot size is 968m. Measurements on micro-pores having different sizes revealed that a constant compensation parameter (i.e., C=85, 96, 120m) is not fully effective at the micro-scale, where average errors still remain at -24%, -18.8%, and -16% for compensations equals to 85, 96 and 120m, respectively. A further experimental campaign allowed the identification of an effective nonlinear compensation law where the compensation parameter depends on the micro-feature size C= f (D). Results show a sharp improvement in dimensional accuracy on micro-pore fabrication, with errors consistently below +8.2%. The proposed compensation method can be extended for the fabrication of any micro-features without restrictions on the specific technology implementation. Concerning the inaccuracy introduced by the laser path, experimentation with a customized part allowed the optimization of the part orientation to reduce the errors and their differences along the X and Y machine axes.

Improper sitting positions are known as the primary reason for back pain and the emergence of musculoskeletal disorders (MSD) among individuals who spend prolonged time working with computer screens, keyboards, and mice. At the same time, it is well understood that automated technological tools can play an important role in the process of unhealthy habit alteration, so plenty of research efforts are focused on research and technology development (RTD) activities that aim to provide support to the prevention of back pain or the development of MSD. Here, we report on creating a new resource in support of RTD activities aiming at the automated detection of improper sitting positions. It consists of multimodal multisensory recordings of 100 persons made with a video recorder, camera, and wrist-attached sensors that capture physiological signals (PPG, EDA, Skin temperature), as well as motion sensors (three-axis accelerometer). Our multimodal multisensory dataset (MMD-MSD) opens new opportunities for modeling the body stance (sitting posture and movements), physiological state (stress level, attention, emotional arousal, valence), and performance (success rate on the Stroop test) of people working with a computer. Finally, we demonstrate two use cases: improper neck posture detection from pictures and cognitive load detection from physiological signals.

This paper presents the PEnsemble 4 model, a sophisticated machine learning framework that integrates IoT-based environmental data to accurately forecast maize yield. With the projected significant growth in global maize demand over the next decade, the inherent risks posed by the crop’s dependence on weather conditions necessitate improved prediction capabilities. The PEnsemble 4 model, developed with high accuracy, incorporates comprehensive datasets encompassing soil attributes, nutrient composition, weather conditions, and UAV-captured vegetation imagery. By employing a combination of Huber and M estimates, the PEnsemble 4 model effectively analyzes temporal patterns in vegetation indices, specifically CIre and NDRE, which serve as reliable indicators of canopy density and plant height. In addition, this research significantly contributes to precision agriculture by offering an efficient and sustainable alternative to conventional farming practices through precise yield predictions. Notably, the PEnsemble 4 model enables earlier estimation, advancing the timeline for yield prediction from the conventional day 100 in the R6 stage to day 79 in the R2 stage. This improvement enhances decision-making processes in farming operations. The remarkable accuracy rate of 91% underscores the importance of adopting a multifaceted data approach that harnesses IoT-derived environmental insights. Additionally, the PEnsemble 4 model extends its benefits beyond yield prediction, facilitating the detection of water and crop stress, as well as disease monitoring in broader agricultural contexts. Ultimately, the PEnsemble 4 model establishes a new standard in maize yield prediction, revolutionizing crop management and protection through the synergistic utilization of IoT and machine learning technologies.

The processability of conductive polymers such as polyaniline (PANI) still poses a challenge due to their properties. The use of stabilizers, compatible and able to interact with PANI, to obtain dispersible and stable colloids is described in this work. To this aim, potato starch has been used as a steric stabilizer for the preparation of polyaniline (emeraldine salt, ES)/starch biocomposites, by exploiting oxidative polymerization of aniline in aqueous solutions containing different ratios of aniline and starch (% w/w). The polyaniline/starch biocomposites were subjected to structural and spectroscopic analyses, thermal analysis, morphological analysis and electrochemical analysis. The samples were then tested for their dispersibility/solubility in various organic solvents. The results showed the formation of PANI/starch biocomposites with an overall smaller size than starch particles, with improved aqueous dispersion and solubility in organic solvents. Although X-ray diffraction and differential scanning calorimetry analyses indicated a loss of crystallinity in the biocomposites, the cyclic voltammetry tests showed that all PANI ES/starch biocomposites display improved redox exchange properties.

In the context of improving aircraft safety, this study focuses on the development and evaluation of a graphene-based ice detection system using an environmental chamber. The research is driven by the need for more accurate and efficient ice detection methods, crucial in mitigating in-flight icing hazards. The methodology employed involves testing flat graphene-based sensors in a controlled environment, simulating a variety of climatic conditions that could be experienced in an aircraft during its entire flight. The environmental chamber enabled precise manipulation of temperature and humidity levels, thereby providing a realistic and comprehensive test bed for sensor performance evaluation. The results were significant, revealing the graphene sensors’ heightened sensitivity and rapid response to the subtle changes in environmental conditions, especially the critical phase transition from water to ice. This sensitivity is the key to detecting ice formation at its onset, a critical requirement for aviation safety. The study concludes that graphene-based sensors, tested under varied and controlled atmospheric conditions, exhibit a remarkable potential in enhancing ice detection systems for aircraft. Their lightweight, efficient and highly responsive nature makes them a superior alternative to traditional ice detection technologies, paving the way for more advanced and reliable aircraft safety solutions.

With the increasing interest in CM as a potential source of nutrients and bioactive compounds, there arises a necessity to delve into methods for its processing and drying. Over recent decades, a significant amount of research has been conducted on the chemical composition of CM and its potential health benefits. Consequently, this study is directed towards examining CM drying technology, including an analysis of the influence of different drying methods on its chemical composition and nutri-tional properties. The objective of this review is to systematically summarize the available literature on CM drying processes and their impact on its chemical composition. Special attention is devoted to comparing various drying methods such as freeze-drying, spray drying, and freeze-drying, as well as investigating factors affecting the quality of dried CM. To achieve this goal, we scrutinize a series of studies published between 2003 and 2022 to identify optimal drying methods that promote the maximum preservation of CM's nutritional components and bioactive compounds. Additionally, we explore possibilities for reducing drying time to enhance production efficiency. This research is grounded in the analysis of data from diverse scientific research databases, including Scopus and Google Scholar, encompassing a systematic review of scientific literature and a comparative analysis of the obtained results.

Drosophila melanogaster serves as a important research model both for genetic investigations and for the study of metal toxicity, facilitating the elucidation of physiological mechanisms comparable to those of human organisms. In our research, we evaluated the toxicity effect resulting from exposure to various concentrations of lead and copper on the prolificity rates throughout the life cycle (egg-adult) of four genotypes of Drosophila melanogaster: wild-type (control), white, brown, and white-vestigial. During our study, the prolificity rates were examined across three repetitions under the impact of exposure to concentrations of 0.50, 1.00, 2.00, and 4.00 mM of copper (CuSO₄) and lead (Pb(C₂H₃O₂₎₂). Prolificity rates throughout the life cycle exhibited variations as a direct consequence of genetic factors, the concentration of exposure, and the specific type of metal, either copper or lead. The mutant white-vestigial genotype revealed an IC₅₀ concentration for prolificity inhibition at lower doses of 2.00 mM for copper and 4.00 mM for lead, in contrast to the control genotype (wild-type), which exhibited an inhibition concentration rate >IC₅₀ of 4.00 mM only in the case of copper. Our results concluded that the (i) dose influences the prolificity rate in a directly proportional manner, (ii) comparative analyses between copper and lead revealed that copper displayed toxicity across all genotypes within the concentration range of 0.50 mM to 2.00 mM. In contrast, lead exhibited toxicity within the concentration range of 1.00 mM to 4.00 mM, highlighting a (iii) more acute toxicity characteristic in the case of copper. Thus, the results of this research reflect the importance of using Drosophila melanogaster as a genetic model in the comparative study of the interaction between genetic factors and the toxicity of metals, offering significant insights into monitoring their impact and defining the maximum permissible doses on organisms.

This article summarizes the results of a research conducted to create an intelligent platform supporting small farmers growing vegetables. In Bulgaria, many farmers use relatively small areas for their production. Considering this situation, the platform is designed for regional use, trying to make maximum use of the specific climatic features of the monitored microdistrict. Consequently, special attention is paid to the possibilities of adapting the platform to the specific environment in which the observed plants grow. Thus, the platform is implemented as an agent-oriented system providing needed flexibility. The core of the platform is a personal assistant, which is responsible for tracking the vegetation cycle of the monitored crop and, upon detection of anomalies, preparing warnings to the farmer. The general architecture of the platform is also presented. In a distributed knowledge base, agriculture-specific knowledge are stored. Furthermore, a standardized interface for receiving data from the sensor networks located in the production areas is briefly described. Currently, the platform is being tested for monitoring four varieties of tomatoes grown on the territory of the national research center for potato breeding. Special attention is paid to the measurements carried out. Conclusions have been drawn that will help improve the platform.

Three-dimensional (3D) printing technology, also known as additive manufacturing (AM), has emerged as an attractive state-of-the-art tool for precisely fabricating functional materials with complex geometries, championing several advancements in tissue engineering, regenerative medicine, and therapeutics. However, this technology has an untapped potential for biotechnological applications, such as sensor and biosensor development. By exploring these avenues, the scope of 3D printing technology can be expanded and pave the way for groundbreaking innovations in the biotechnology field. Indeed, new printing materials and printers would offer new possibilities for seamlessly incorporating biological functionalities within the growing 3D scaffolds. Herein, we review the extrusion-based 3D printing modalities emphasizing biosensor applications. We highlighted the application of natural, synthetic, and composite biomaterials as 3D-printed soft hydrogels. Emphasis was placed on the approach by which the sensing molecules were introduced during the fabrication process. Finally, the future perspective was provided.

A common problem in education has always been to get students to achieve an adequate level of motivation and engagement. Many evidences show that gamification has the potential to make learning more engaging, motivating and effective. However, it is essential to design gamified experiences thoughtfully, ensuring that they align with educational objectives and promote meaningful learning outcomes, and so the lack of established design methodologies can lead to unintended consequences.

A multimodal detection system with complementary capabilities for efficient detection was developed for impurity detection. The system consisted of a visible light camera, a multispectral camera, image correction and registration algorithms. It can obtain spectral feature and color feature at the same time, and has higher spatial resolution than a single spectral camera. This system was applied to detect impurities in Pu ’er tea to verify its high efficiency. The spectral and color features of each pixel in the images of Pu ’er tea were obtained by this system and used for pixel classification. The experimental results show that the accuracy of Support Vector Machine (SVM) model based on combined features is 93%, which is 7% higher than that based on only spectral features. By applying median filtering algorithm and contour detection algorithm to the label matrix extracted from pixel-classified images, 8 impurities except hair were detected successfully. Moreover, taking advantage of the high resolution of visible light camera, small impurities can be clearly imaged. By comparing the segmented color image with the pixel-classified image, small impurities such as hair could be detected successfully. Finally, it is proved that the system can obtain multiple images to allow a more detailed and comprehensive understanding of the detected items, and has excellent ability to detect small impurities.

In this paper, we introduce a specialized, fully automated experimental arrangement designed for assessing the effectiveness of augmented and virtual reality technologies in healthcare setting and explore its design principles focusing on depth sensor characterization. The main goal of this project is to establish a robust benchtop platform for the quantitative evaluation of extended reality technologies in a controlled environment, emphasizing the practical assessment of augmented reality head-mounted devices. We outline a design concept and considerations for an experimental configuration aimed at creating a realistic testing environment. This apparatus comprises an observation platform mounted on a three-degree-of-freedom motorized system and a test phantom stage. Focusing on real-case scenarios, we utilized a range of sensors, including readily available range-sensing cameras and commercial augmented reality headsets, such as the Intel RealSense L515 LiDAR camera, mounted on the motion control system. The setup enabled automated data collection and facilitates controlled assessments and validation of various facets of augmented reality technologies, including object, hand, and head tracking, as well as static and dynamic image registration. This paper describes the system architecture, the process of automated data collection, and presents several evaluation studies conducted with this setup, providing insights into the quality and temporal noise associated with static or moving objects or observers in augmented reality applications.

Densely urbanized areas, with a low percentage of green vegetation, are highly exposed to Heat Waves (HW) which nowadays are increasing in terms of frequency and intensity also in the middle-latitude regions, due to ongoing Climate Change (CC). Their negative effects may combine with those of the UHI (Urban Heat Island), a local phenomenon where air temperatures in the compact built up cores of towns increase more than those in the surrounding rural areas, with significant impact on the quality of urban environment, on citizens health and energy consumption and transport, as it has occurred in the summer of 2003 on France and Italian central-northern areas. In this context this work aims at designing and developing a methodology based on aero-spatial remote sensing (EO) at medium-high resolution and most recent GIS techniques, for the extensive characterization of the urban fabric response to these climatic impacts related to the temperature within the general framework of supporting local and national strategies and policies of adaptation to CC. Due to its extension and variety of built-up typologies, the municipality of Rome was selected as test area for the methodology development and validation. First of all, we started by operating through photointerpretation of cartography at detailed scale (CTR 1: 5000) on a reference area consisting of a transect of about 5x20 km, extending from the downtown to the suburbs and including all the built-up classes of interest. The reference built-up vulnerability classes found inside the transect were then exploited as training areas to classify the entire territory of Rome municipality. To this end, the satellite EO HR (High Resolution) multispectral data, provided by the Landsat sensors were used within a on purpose developed "supervised" classification procedure, based on data mining and “object-classification” techniques. The classification results were then exploited for implementing a calibration method, based on a typical UHI temperature distribution, derived from MODIS satellite sensor LST (Land Surface Temperature) data of the summer 2003, to obtain an analytical expression of the vulnerability model, previously introduced on a semi-empirical basis.

The enterprise software sector is experiencing a significant transformation driven by rapid technological progress and evolving business needs. An effective release management process is crucial for the solution providers and customers, as they incorporate the principles of Industry 4.0 and 5.0. With the growing dependence on software solutions and services, ensuring their quality, reliability, and security is highly necessary. The release management process incorporates strategic planning, regression testing, accurate deployment, and continuous monitoring of software updates. However, the rapid advancements in artificial intelligence (AI) and machine learning (ML) create a unique challenge to the release management process. The existing research needs to address the necessary adaptations for Industry 5.0, mainly in product-based software organizations, to the release management process without a change management system. After working with several software solution stakeholders, based on the responses from SaaS project stakeholders, we have presented a revised software release readiness workflow by incorporating a change management module. The preliminary result based on data over a limited period of time indicates that the revised workflow has the potential to improve the management of slippage, particularly by more effectively addressing NFR-related issues, thereby resulting in more predictable and reliable release cycles.

In this work, an innovative numerical approach for polylinear approximation (polylinearization) of non-self-intersecting compact sensor characteristics (transfer functions) specified either pointwise or analytically is introduced. The goal is to optimally partition the sensor characteristic, i.e. to select the vertices of the approximating polyline (approximant) along with their positions on, the sensor characteristics so that the distance (i.e. the separation) between the approximant and the characteristic is rendered below a certain problem-specific tolerance. To achieve this goal, two alternative non-linear optimization problems are solved, whose essential difference is in the adopted quantitative measure of the separation between the transfer function and the approximant. In the first problem, which relates to absolutely integrable sensor characteristics (their energy is not necessarily finite, but they can be represented in terms of convergent Fourier series), the polylinearization is constructed by numerical minimization of the L^1--metric (a distance-based separation measure), concerning the number of polyline vertices and their locations. In the second problem which covers the quadratically integrable sensor characteristics (whose energy is finite, but they do not necessarily admit a representation in terms of convergent Fourier series), the polylinearization is constructed by minimizing numerically the L^2-metric (area-, or energy-based separation measure) for the same set of optimization variables –the locations, and the number of polyline vertices.

Improper disposal of waste plastic has caused serious ecological and environmental pollution problems. Transforming plastics into high value-added chemicals can not only achieve efficient recycling of waste plastics, but also an effective way to control white pollution. The catalyst selectively breaks the C-C bond of polyolefin plastic under heat treatment and converts it into liquid fuel, thus realizing sustainable recycling of plastics and has a good development prospect. This review provides a detailed overview of the current development of catalytic pyrolysis, catalytic hydrolysis, solvent decomposition and supercritical hydrothermal liquefaction for cracking plastics to make fuel oil. The reaction mechanism, influencing factors and promoting effects of catalysts in various degradation technologies are analyzed and summarized and the latest proposed tandem reaction for degrading plastics is briefly introduced. Finally, some optimization paths of waste plastic pyrolysis to fuel oil technology are proposed: synergies between mixed raw materials, in-depth exploration of catalysts, design and manufacture of reactors that match the pyrolysis technology. All these are important research directions for promoting the industrialization of plastic pyrolysis to fuel oil.

Graphene hybrid-filler polymer composites have emerged as prominent materials that revolutionize heavy industries. This study encapsulates the in-depth analysis of different influential factors such as filler/graphene type, aspect ratios, dispersion methods, filler-matrix compatibility, fiber orientation, synergistic effects, different processing techniques, and post-curing conditions that affect the processing, properties and determine the resultant applications of graphene hybrid polymer composites. Additionally, it discusses the substantial role of graphene collaboration with other fillers such as carbon nanotubes, silica, nano-clays and metal oxides to produce functionalized hybrid polymer composites with synergistically enhanced tailored properties to offer solutions for heavy industries like aerospace, automotive, electronics, and energy harvesting. The review concludes with some suggestions and outlook on the future of these composite materials by emphasizing the need for continued research to fully optimize their potential.

Multi-rotor drones, a kind of unmanned equipment which is widely used in military, commercial consumption and other fields, has been developed very rapidly in recent years. However, their short flight time has hindered the expansion of their application range. This can be addressed by utilizing hydrogen fuel cells, which exhibit high energy density, strong adaptability to ambient temperature, and no pollution emissions, as the power source. Accordingly, the application of hydrogen fuel cells as the power source in multi-rotor drones is a promising technology that has attracted significant research attention. This paper summarizes the development process of hydrogen fuel cell mul-ti-rotor drones and analyzes the key obstacles that need to be addressed for the further development of hydrogen fuel cell multi-rotor drones, including structural lightweight, hydrogen storage methods, energy management strategies. Additionally, prospects for the future development of hydrogen fuel cell multi-rotor drones are presented.

In light of the critical and emerging global challenge posed by the increasing frequency and severity of heatwaves in recent decades, this study demonstrates a practical and robust workflow that bridges the gap in understanding how the effective integration of remote sensing data with ground-based observations can facilitate a comprehensive assessment of spatiotemporal heatwave patterns and trends in the central region of Thailand. This research transcends traditional methods, utilizing air temperature (Tair) and satellite-derived land surface temperature (LST) data from 1981 to 2019. Results exhibit that an analysis of Tair indicates increasing daytime heatwaves in peri-urban areas, with significant trends in heatwave number (HWN), heatwave frequency (HWF), and heatwave duration (HWD), heatwave amplitude (HWA) rises in urban settings while nighttime heatwaves significantly intensify in rural locales. Notably, LST trends reveal varied patterns, with peri-urban areas showing marked daytime increases in heatwave magnitude (HWM), HWA, and HWF. Correlation analysis (p=0.05) highlights strong daytime associations between Tair and LST in rural (HWN, HWF, HWD, r>0.90) and peri-urban (HWM, HWA, r>0.65) regions. Overall, this study advances approaches to the adaptable measurement and spatial-temporal pattern of heatwave-related risk areas, providing insights for decision-makers to develop sustainable practices and strategies for climate change adaptation.

The study investigated the usage of open data in public organizations, focusing on the motives, preferences, and governance ideals that determine their quality. The study shed light on how open data platforms are created and improved, as well as their influence on government operations. The primary goal was to understand the motivations behind the usage of open data, evaluate gov-ernance ideals, and examine institutions' efforts to standardize data formats. Hierarchical regres-sion analysis divides variables into core reasons and different preferences, demonstrating a need for "diversification" in order to use open data effectively. Efficiency, accountability, community impact, knowledge, and high-quality service delivery are all emphasized in governance value analysis. The institution's dedication to standardizing open data formats is evidenced by legislative measures and the integration of many technologies. The findings illustrate the institution's dual strategy of em-ploying traditional techniques and new technologies for effective data management. The report suggests increasing data openness and standardization, investing in ongoing training, upgrading alerting and awareness systems, and adopting specific regulations for open data use. Monitoring and feedback techniques are critical for adjusting and refining open data services to satisfy de-velopment needs. This study adds to the scientific knowledge of open data use by highlighting important motives, preferences, and governance ideals. The offered guidelines provide practical insights for public organizations looking to improve their open data platforms by promoting openness, efficiency, and community participation.

Urban rail transit hub platform is the most important area for passenger flow distribution. In order to calculate passenger flow volume in platform and evaluate platform service level during rush hours, this paper presents a method for modeling and simulation of passenger flow distribution in platform. Passenger flow distribution model (PFDM) is proposed based on the basic analysis and the superposition principle of passenger flow. Simulation design for PFDM is proposed by Anylogic, which contains simulation process and simulation model. Experiment results show that PFDM and simulation design are effective and accordant with the reality scenario, and the simulation precision is comparatively ideal. This research could provide a beneficial reference for train scheduling and operation management under the viewpoint of traffic safety and service level.

Glycerol represents a useful functional component of heat-transfer fluids. Glycerol is known to be triboelectrically active. We report how the flow of glycerol, stopped in a cylindrical coiled pipe, influences horseradish peroxidase (HRP) enzyme. Namely, glycerol flow was pumped through the coil and then stopped. After that, we incubated the 0.1 µM solution of HRP near the side of the coil, and then adsorbed HRP onto mica. This operation markedly increased the HRP aggregation on mica in comparison with the control sample. We explain this phenomenon by the influence of triboelectrically induced electromagnetic fields. Our results can be useful in the development of flow-based systems for biosensors and bioreactors.

As marine traffic is contributing to pollution and mostly have predictable route with repetitive load profiles, to reduce their impact on environment, hybrid system with proton exchange membrane fuel cells (PEMFC-s) and battery pack, is promising replacement. For this purpose, the numerical model of repowered existing vessel that have two diesel engines with 300 kWe is developed. The goal of this paper is to develop numerical model which analyzes and determine equivalent hybrid ship propulsion system for known traveling route. The developed numerical model consists of an interconnected system with PEMFC stack and battery pack as power sources. Numerical model is developed and optimized to meet minimal required power demand for successful route demand, which has variable loads and daily sails six-time same voyage- in total 54 nautical miles. The results have shown that equivalent hybrid power system consists of 300 kWe PEMFC stack and battery pack with 424 kWh battery and state of charge varying between 20 and 87%. To power this new hybrid power system, hydrogen tank of 7200 l holding 284.7 kg at pressure of 700 bar is needed, compared to previous system that spend 1524 kg of diesel and generate 4886 kg of CO2.

Dye/salt separation has gained increasing attention in recent years, prompting the quest for cost-effective and environmentally-friendly raw materials for synthesis high performance nanofiltration (NF) membrane for effective dye/salt separation. Herein, a high-performance loose structured NF membrane was fabricated by via a simple vacuum filtration method using a green nanomaterial, 2,2,6,6-tetramethylpiperidine-1-oxide radical (TEMPO)-oxidized cellulose nanofiber (TOCNF), by sequentially filtrating larger-size and finer-size TOCNFs on a microporous substrate, followed by cross-linked with trimesoyl chloride. The resultant TCM membrane possesses a separating layer composed entirely of pure TOCNF, eliminating the need for other polymer or nanomaterials additives. TCM membranes exhibits high performance and effective dye/salt selectivity. Scanning Electron Microscope (SEM) analysis shows that the TCM membrane with Fine-TOCNF layer has a tight layered structure. Further characterizations via Fourier transform infrared spectroscopy (FTIR) and X-ray diffraction (XRD) confirm the presence of functional groups and chemical bonds of the crosslinked membrane. Notably, the optimized TCM-5 membrane exhibits a rejection rate of over 99% for various dyes (Congo red, orange yellow) and 14.2% for NaCl, showcasing a potential candidate for efficient dye wastewater treatment.

The per capita availability of freshwater resources on a global scale is gradually decreasing due to population growth, rapid urbanization, industrialization, and modern lifestyles. In this situation, wastewater management becomes a major concern. Conventional treatment processes used to treat wastewater discharges are not adequate for the advanced removal of pollutants, especially refractory organic pollutants, which are mainly organic compounds that are not easily biodegradable in the environment. The use of photocatalytic membrane reactors (PMRs) for tertiary wastewater treatment has attracted much interest in recent periods, and various configurations have been investigated. The performance of a PMR using an iron doped titanium photo catalyst and Polysulfone-based polymeric membrane for municipal wastewater treatment was evaluated under natural and simulated solar light. Obtained results proved that solar driven PMRs can remove organic loading (COD) with high efficiencies and may represent a suitable alternative for the tertiary treatment step of municipal wastewater.

The supply chain has incorporated products by putting them into hair scarfs. This study introduces the use of mini chips in health and beauty products and can reduce fatigue through enhanced sleep patterns. The mini chip could be placed in the scarf and used as a prototype. RFID technology provides the supply chain with specific information that is used to identify products and make communication easier. (Muhammad, et. al. 2013) This paper presents a new tool herein referred to as a scarf prototype which is developed to analyse EMG (electromyogram), ECG (electrocardiography), EEG (electroencephalogram), and EOG (electro-oculogram) signals that focuses in the area of sleep disorders. The mini chips used can be used to determine a solution for sleep disruption by using automated analytics. This could lead to improvement in our understanding of sleep disruption and overall sleep physiology. Automated technology allows repeated measurements, evaluation of sleep patterns, and provide suggestions to improve a person’s quality of sleep. This analysis compares the use of polysomnography and the scarf prototype. The analytics provide models and shows correlation between variables, such as EMG, ECG, EEG, and EOG. This study shows that the results from the scarf prototype is just as reliable as the original method, polysomnography.

A hybrid material, consisting of commercially available nitrocellulose (NC) membrane non-covalently modified with amino-polyethylene glycol functionalized reduced graphene oxide (NH2-PEG-rGO) nanoparticles, was successfully synthesized for oligonucleotide extraction. Fourier Transform Infrared Spectroscopy (FTIR) confirmed the modification of the NC membrane, revealing characteristic peaks of both compounds NC and NH2-PEG-rGO. Scanning Electron Microscopy (SEM) exhibited morphological changes in the NC/NH2-PEG-rGO hybrid membrane, marked by the introduction of NH2-PEG-rGO particles, resulting in a distinctly smothered surface compared to the porous surface of the NC control membrane. Wettability assays revealed hydrophobic behavior for the NC/NH2-PEG-rGO hybrid membrane, with a water contact angle exceeding 90°, contrasting with the hydrophilic behavior characterized by a 16.7° contact angle in the NC membrane. The performance of the NC/NH2-PEG-rGO hybrid membrane was evaluated for the extraction of ssDNA with fewer than 50 nucleotides from solutions containing various ionic species (MnCl2, MgCl2, and MnCl2/MgCl2). The NC/NH2-PEG-rGO hybrid membrane exhibited optimal performance when incubated in MgCl2, presenting the highest fluorescence emission at 525 relative fluorescence units (r.f.u.). This corresponds to the extraction of approximately 610 pg (≈13%) of the total oligo-DNA, underscoring the efficacy of the pristine material, which extracts 286 pg (≈6%) of oligo-DNA in complex solutions.

Polymer inclusion membranes (PIMs), which contained cellulose tri-acetate used as a polymer base, a plasticizer in the form of o-NPOE, and meso-tetra methyl tetrakis-[methyl-2-(4-acetlphenoxy)] calix[4]pyrrole (KP) used as a carrier, were prepared and tested for the effective purification of aqueous solutions of methylene blue dye. The scanning electron microscope (SEM), thermogravimetric analysis (TGA), and attenuated total reflection Fourier transform infrared (ATR-FTIR) were used to define the microstructure and surface of PIMs. Experimental results showed that with the increased concentration of methylene blue in an aqueous solution, the removal percentage also increased. Further observation also showed that the flux increased with the rise of the source phase pH values from 3 to 10. The carrier and plasticizer content in the membrane significantly influenced the membrane’s transport properties. The optimal composition of the membrane in per cent by weight was for KP: 74% plasticizer; 18% support; 8% carrier. It was shown that the membrane with optimal composition showed good reusability and enabled the easy and spontaneous separation of methylene blue from aqueous solutions.

Floods, recognized for their erratic behavior and devastating effects, are a significant threat as a natural disaster. In Brunei Darussalam, the impact of climate change is becoming increasingly evident through higher temperatures and an expected increase in annual rainfall (5.0mm per year from 2021 to 2050), highlighting the critical need for updated flood risk management techniques. In line with the climate resilience and adaptation objectives of WAWASAN 2035, this paper introduces an innovative approach—a cutting-edge flood risk management framework that utilizes the capabilities of big data analytics, sophisticated machine learning algorithms, and smart Internet of Things (IoT) sensors. Traditional methods, which rely on numerical and physical data modeling, often do not provide precise short-term flood forecasts. Our suggested framework uses machine learning to analyze real-time flood forecasting, sensor data and enhance warning systems, addressing the shortcomings of traditional approaches. The key advantage of this approach is its potential to drastically decrease flood-related damages, protect lives, and boost infrastructure resilience. This proposal is not only in aligns with Brunei's vision for a safe and climate-adaptable future but also marks a significant step forward in adopting innovative and sustainable flood risk management solutions amidst an evolving climate.

Introduction: Atrial fibrillation (AF) is a common cardiac arrhythmia whose prevalence rises with age and is linked to increased morbidity and mortality due to the risk of thromboembolism. Management typically involves anticoagulation and rhythm control, but the treatment of elderly patients with multiple comorbidities requires careful consideration of drug side effects and interactions. Cibenzoline, a Vaughan-Williams class IA antiarrhythmic, is effective against AF but has risks of toxicity, especially in older people and those with renal impairment, due to its renal excretion and prolonged half-life in these populations. Discussion: This paper presents a case of an 80-year-old woman with paroxysmal AF who suffered cardiac arrest due to cibenzoline toxicity despite receiving standard adjusted dosages. The patient's cibenzoline blood concentration was significantly higher than the therapeutic range, leading to cardiotoxicity, which was exacerbated by drug interactions with bisoprolol and edoxaban, both metabolized by the CYP3A4 enzyme. Venoarterial extracorporeal membrane oxygenation (V-A ECMO) and intra-aortic balloon pump (IABP) successfully managed the cardiac arrest. This case emphasizes the unpredictable pharmacokinetics of cibenzoline in elderly patients with renal impairment and the need for vigilant therapeutic drug monitoring to avoid adverse events. Conclusions: Cibenzoline can pose a significant risk of severe toxicity in elderly patients with renal impairment, and drug interactions may potentiate this risk. The paper underscores the importance of careful dose adjustment and monitoring of drug levels in this population. In cases of cibenzoline-induced cardiac arrest, V-A ECMO and IABP are effective treatment modalities. The case study serves as a critical reminder for clinicians to remain vigilant for drug-induced complications and to apply aggressive supportive treatments when necessary.

In recent years there has been increasing interest in the discovery of new natural herbal remedies for the treatment of common conditions such as diabetes and inflammatory diseases. In this context, this paper analyzed the antidiabetic and anti-inflammatory potential of two plants of the genus Artemisia: Artemisia absinthium (wormwood) and Artemisia vulgaris (mugwort) and Trigonella foenum-graecum (fenugreek) plants less studied from this point of view. Thus, hydroal-coholic extracts (50% EtOH v/v, 10% mass) were made, which were processed by membrane technologies, micro- and ultrafiltration, in order to concentrate the biologically active principles. The extracts were then analyzed in terms of content in active principles of interest (polyphenols, flavones). The antidiabetic activity of the extracts was analyzed by testing their ability to inhibit α-amylase and α-glucosidase and the anti-inflammatory activity by testing the ability to inhibit hyaluronidase (HYA) and lipoxygenase (LOX). Thus, the T. foenum-graecum extracts showed a high inhibitory activity on α-amylase 3.22 ± 0.3 g / mL (compared to the standard used - IC50 acarbose = 3.5 g / mL) and a high inhibitory activity on LOX: 19.69 ± 0.52 g/mL (compared to all standards used). The concentrated extract of Artemisia vulgaris showed increased activity of inhibition of α-amylase - IC50 = 8.57 ± 2.31g/mL and moderate activity of inhibition of HYA - IC50 = 17.18 g/mL compared to ibuprofen, the standard used - IC50 = 5.73 g/mL. The concentrated extract of Artemisia absinthium showed a pronounced activity of inhibition of LOX - IC50 = 19.71 g / mL, compared to the standard - rutin - IC50 = 22.34 g/mL).

A time-sequential working, spatially multiplexed autostereoscopic 3D display design consisting of a fast switchable RGB-color filter array is presented. The wavelength-selective filter barrier emits the light from a display over a larger active area than common autostereoscopic barrier displays. An optical modelling of wavelength-selective barriers has been used for instance to calculate the light ray distribution properties of that arrangement. To find well working display designs, automated searches by simulation and computational evaluation has been proceeded. Wavelength-selective filter barrier arrangements exhibit characteristics different from common barrier displays with similar barrier pitch and ascent. In particular, these constructions show strong angular luminance dependency under barrier inclination specified by correspondent slant angle. In time-sequential implementation it is important to avoid that quick eye or eyelid movement lead to visible color artifacts. In the millisecond regime tunable liquid crystal Fabry-Pérot color filters for the colors red, green and blue are presented. They consist of a sub-micrometer thick nematic layer sandwiched between dielectric mirrors and ITO-electrodes. These cells shall switch narrow-banding light of red, green or blue. An array for a glasses-free 3D display has to be equipped with several thousand switchable filter elements having different color apertures. The newly introduced design is usable as a multi user display as well as a single user system with user adaptive control.

The Circular Bioeconomy (CBE) combines the concepts of bioeconomy and circular economy. As an alternative concept to the current fossil-based, linear economy, it de-scribes an economy based on the efficient valorization of biomass. It is regional in nature and aims to improve sustainability. An analysis of the transition process, by identifying its success criteria and assessing its impacts through the modelling of technology-specific scenarios is necessary to ensure that CBE concepts are sustainable. However, a compre-hensive consideration of regional influences on both is lacking. Based on extensive literature research and an expert survey, we (i) present a compre-hensive catalog of CBE success criteria and discuss their region-specific character and (ii) develop a methodology based on evaluation matrices that enable to match CBE technolo-gies with regions. The matrices support the evaluation of technological and regional characteristics influencing the successful CBE implementation. The results show that the success criteria "biomass resources", "technological", and "social" are perceived as highly important, and that most of the success criteria are both region- and technology-specific, highlighting the relevance of developing matrices to match them. We describe such matrices indicatively for the two broadest and most im-portant success criteria clusters “social acceptance” and “biomass supply chain”. With this, we substantiate the regional nature of CBE and raise the awareness on the importance of considering regional conditions in CBE transition processes. Furthermore, we provide practical guidance on how regional conditions can be reflected in the selection of technologies, e.g. in regional CBE technology scenarios.

This paper undertakes a comprehensive review to underscore the central role of sustainability in the evaluation and innovation of jet grouting technologies. It meticulously traces the evolution of evaluation methodologies, emphasizing the imperative of sustainable practices throughout history. Traditional evaluation paradigms are examined alongside contemporary trends, with a particular focus on sustainability metrics and visualization techniques. Through an examination of innovative jet grouting technologies, this paper illustrates how sustainability principles have driven advancements aimed at improving the efficiency and environmental impact of jet grouting methods. Central to this review is an assessment of sustainability across multiple dimensions, including method applicability, installation and operational compatibility, and the performance of the resulting jet grouted piles. By emphasizing sustainability considerations, the paper highlights the intrinsic link between environmental integrity and technological innovation in the field of jet grouting. In addition, it discusses analytical evaluation methods designed to proactively address sustainability concerns prior to construction, thereby promoting a more environmentally responsible approach. Finally, this paper presents a pioneering evaluation framework that integrates real-time monitoring and visualization tools, allowing stakeholders to track sustainability milestones throughout the construction process. By emphasizing sustainability as a guiding principle, this review advocates for a paradigm shift toward more ecologically sound and resilient jet grouting practices.

This article develops algorithms for the characterization and the visualization of micro-scale features by using a small number of sample points, and with a goal to mitigate for the measurement shortcomings which are often destructive or time consuming. We implement the algorithms to rapidly examine the microscopic features of a Microelectromechanical System (MEMS) surface. Such images are highly dense; therefore, traditional image processing techniques might be computationally expensive. The contribution of this research include first, we develop local and global algorithm based on modified Thin Plate Spline (TPS) model to reconstruct high resolution images of the micro-surface’s topography, and its derivatives by using low resolution images. Second, we obtain a bending energy algorithm from our modified TPS model, and use it to filter out image defects. Finally, we develop a computationally efficient Windowing technique, which combines TPS and Linear Sequential Estimation (LSE), to enhance the visualization of images. The Windowing technique allows rapid image reconstruction based on the reduction of inverse problem.

This paper constituted an extension of two previous studies concerning the mathematical development of the grain boundary grooving in polycrystalline thins films in the cases of the evaporation/condensation and diffusion taken separately. The thermal grooving processes are deeply controlled by the various mass transfer mechanisms of evaporation–condensation, surface diffusion, lattice diffusion, and grain boundary diffusion. This study proposed a new original analytical solution to the mathematical problem governing the grain groove profile in the case of simultaneous effects of evaporation-condensation and diffusion in polycrystalline thin films submitted to thermal and mechanical stress, and fatigue effects; by resolving the corresponding fourth-order partial differential equation ∂y∂t=C∂2y∂x2-B∂4y∂x4 obtained from the approximation y'2≪1. The comparison of the new solution to that of diffusion alone proved an important effect of the coupling of evaporation and diffusion on the geometric characteristics of the groove profile. A second analytical solution based on the series development was also proposed. It was proved that change of the boundary conditions of the grain grooving profile largely affected the different geometric characteristics of the groove profile.

Recent interest in intestinal hormones has risen with the idea that they modulate glucose tolerance and food intake through a variety of mechanisms, and such hormones like peptide YY (PYY), ghrelin, glucagon-like peptide (GLP)-1 and 2, and cholecystokinin (CKK) are therefore excellent therapeutic candidates for the treatment of diabetes and obesity. Furthermore, in the recent years, multiple studies suggest that the microbiota is critically important for normal host functions, while impaired host microbiota interactions contribute to the pathogenesis of numerous common metabolic disorders. In this study, we considered the nutraceutical effects of β-glucans added to pasta at the concentration of 6g\100g. Ten participants have been recruited and hematochemical analyses and intestinal hormones tests have been performed before and after 30 days of pasta intake. Stool specimens have been studied for Lactobacillus Fermentum, Lactobacillus acidophilus, Lactobacillus salivarius, Bifidobacterium longum, and Enterococcus faecium presence before and after 30 days of nutritional intervention. After 30 days of regular intake of pasta enriched by β-glucans results have been evaluated. In conclusion, pasta prepared from barley flour enriched with β-glucans at 6% exhibit promising responses on glucose metabolism, on intestinal hormones responses and on microbiota modification.

The literature offers limited information on the effect of obesity on the rate of force development, a critical parameter for mobility in older adults. The objectives of this study were; to explore the influence of obesity on RFD in older adults and to examine the association between this neuromuscular parameter and walking speed. 42 older adults were classified into two groups: the control group (CG, n=22; age=81.13±4.02 years; Body mass index (BMI)=25.13±3.35 kg/m²), and the obese group (OG, n=20; age=77.71±2.95 years; BMI=34.46±3.25 kg/m²). Walking speed (m/s) was measured using the 10-meter walking test. Neuromuscular parameters of the plantar flexors were evaluated during a maximal voluntary contraction test using a dynamometer. The RFD was calculated from the linear slop of the force – time curve in two phases: from the onset of the contraction to 50 ms (RFD50-100) and from 100 to 200 ms (RFD100-200). The gait speed was lower in the OG compared to the CG (p

In the last decade, robotic-mediated rehabilitation has emerged as a potential solution to improve repetitive task training. Each device in this field has a unique development history shaped by engineers’ expertise in specific programming languages or platforms. In this work we adopt an approach that tries to abstract from the final implementation with the aim to make control logic more shareable and understandable. The authors will present the outcomes of the application of a Rapid Control Prototyping strategy to an upper-limb robotic exoskeleton. A model-based design approach implemented on a real-time target machine is presented. This modern design approach was explored with several control strategies and was used to test the exoskeleton’s performances. The proposed method highlights how it is possible to develop the entire control architecture in a single programming environment.

The goal of the study presented in this article is to investigate interconnection issues of the Intelligent Electrical Networks (IENs) with the existing ones, as well as the deployment of the appropriate load forecasting demand techniques. The concept of IENs has recently emerged as a potential solution to the global energy problem, due to the more flexible dispersed production units that are involved. In the same context, additional issues, such as the reduction of production-transfer-distribution costs as well as power losses are analyzed as well, via the penetration of Renewable Energy Sources (RESs). To this end, it is necessary to use appropriate advanced infrastructure, where in combination with modern telecommunication networks will make possible the full exploitation of IENs. Moreover, to make the electricity system more efficient, to avoid voltage and frequency imbalance issues and to implement optimal production and consumption planning, the Electric Load Forecast (ELF) is a vital process and plays a key role in the planning as well as in the management of electricity systems. Therefore, recent state of the art approaches in ELF methods are discussed as well.

Dysregulation of cartilage homeostasis and the changes in the density and the architecture of the subchondral bone were postulated as a potent mechanically pathological activity contributing to osteoarthritis (OA) pathogenesis. Extracorporeal shockwave therapy (ESWT) is a new, none invasive and effective method in the treatment of animal OA model. In the current study, we demonstrated that shockwave induced the expression of protein-disulfide isomerase-associated 3 (Pdia-3) which is a multifunctional protein hypothesized to be a significant mediator for 1α,25-Dihydroxyvitamin D3 (1α,25(OH)₂D₃) signaling pathway using two-dimensional electrophoresis. Histological analysis and quantitative polymerase chain reaction (qPCR) were verified and observed that the expression of Pdia-3 at 2 weeks was significantly higher than that of any other group at 4 weeks, 8 weeks, and 12 weeks post-shockwave treatment in early OA knee of rat. The other factors of the 1α,25(OH)₂D₃ rapid membrane signaling pathway including extracellular signal-regulated protein kinases 1 (ERK1), osteopontin (OPG), alkaline phosphatase (ALP), and matrix metallopeptidase 13 (MMP13) were measured and significantly increased by qPCR at 2 weeks post-shockwave treatment in early OA knee. Our proteomic data revealed significant Pdia-3 expression in microenvironments of joint tissue that could be actively responded to ESWT, which may potentially regulate biological function of chondrocytes and osteoblasts in the treatment of OA knee.

The main sources of intrinsic noise in excitable cells at the microcircuit and network levels are the stochastic characteristics of ion channel gating and activation of the synaptic conductance. Studies using in vivo, in vitro, and in silico methods to examine the effects of synaptic background activity were not adequately investigated in non-neuronal excitatory cells, where neurotransmitter-based innervation also occurs. We created a mathematical model to replicate the background synaptic noise dynamics in a non-neuronal cell. We utilized the stochastic Ornstein-Uhlenbeck process to represent excitatory synaptic conductance, which was incorporated into a whole-cell model to produce spontaneous and evoked cellular electrical activities. The single-cell model includes many biophysically detailed ion channels represented by a set of ordinary differential equations in Hodgkin-Huxley and Markov formalisms. This paradigm effectively induced irregular spontaneous depolarizations (SDs) and spontaneous action potential (sAP) resembling in vitro-like electrical activity in the cells. The input resistance decreased by multiple factors, and the spontaneous action potential firing rate elevated. The potential to reach the action potential threshold is altered. Background synaptic activity can alter the input/output characteristics of non-neuronal excitatory cells. Suppressing these baseline activities would facilitate the discovery of new pharmaceutical targets for different clinical diseases.

The development of biofuels and biodiesel industry specifically, has resulted in the generation of large amounts of glycerol as a surplus. The conversion of glycerol, into chemicals with indus-trial interest, through anaerobic fermentation using E. coli as a biocatalyst is an attractive alter-native to improve economic performance in the biodiesel industry, for example through the bi-otransformation of residual glycerol into ethanol. For 2019, the size of the global ethanol market was valued at $ 89.1 billion US dollar. Biodiesel can be produced from several materials like rapeseed, palm, soya, corn, palm kernel, frying oil or olive-pomace oil (OPO). The last, can be extracted from alperujo, byproduct of olive oil process. However, olive-pomace oil converting into biodiesel is not enough established to achieve a global olive-oil/biodiesel derived process with minimized waste generation. Traditionally biodiesel production process produces an equivalent of 10% by mass of glycerol as a waste or by-product. This work explores the conver-sion of residual glycerol into chemicals like ethanol and hydrogen with a focus on projecting raw material potential availability from OPO, contributing to the promotion of the use of biofu-els and biodegradable compounds.

Artificial membrane systems can serve as models to investigate molecular mechanisms of different cellular processes, including transport, pore formation, and viral fusion. However, the current simulacrums such as SUVs, GUVs, and the supported lipid bilayers suffer from issues, namely high curvature, heterogeneity, and surface artefacts, respectively. Freestanding membranes provide a facile solution to these issues, but current systems developed by various groups use silicon or aluminium oxide wafers for fabrication that involves access to a dedicated nanolithography facility and high cost while conferring poor membrane stability. Here, we report the development, characterization and applications of an easy-to-fabricate suspended lipid bilayer (SULB) membrane platform leveraging commercial track-etched porous filters (PCTE) with defined microwell size. Our SULB system offers a platform to study the lipid composition-dependent structural and functional properties of membranes with exceptional stability in a high throughput fashion. With dye entrapped in PCTE microwells by SULB, we show that sphingomyelin significantly augments the activity of pore-forming toxin, Cytolysin A (ClyA) and the pore formation induces lipid exchange between the bilayer leaflets. Further, we demonstrate high efficiency and rapid kinetics of membrane fusion by dengue virus in our SULB platform. Our suspended bilayer membrane mimetic offers a novel platform to investigate a large class of biomembrane interactions and processes.

The vast array of interconnected microbes across earth’s ecosystems and within holobionts has been called the “Internet of Microbes.” Research into the fundamental microbial properties has demonstrated that bacteria and archaea are masters of energy and information collection, storage, transformation, and dissemination using both “wired” and wireless (at a distance) capacities. These features suggest that microbes are quantum entangled within and between earth’s holobionts, and that specific tools affecting energy and information functions could provide an effective strategy for managing microbial populations. Microbes use four critically important microbial networking functions (sound, light, electricity, and magnetism). This narrative review focuses on microbial management based on two of the four: sound and light (as well as related vibrations). These are examined as: 1) tools for managing microbial populations, 2) tools to support new technologies, and 3) tools for healing humans and other holobionts. Given microbial sensitivity to sound, light, and vibrations, it is critical that microbial populations and microbe-laden holobionts are protected from potentially damaging exposures. We conclude that sound, light, and vibrations are useful therapeutic tools that can help support useful microbial populations and help to address ongoing challenges of holobiont disease.

Polyhydroxyalcanoates (PHAs) are biodegradable polymers synthesized in cytoplasmic granules in bacteria, such as Cupriavidus necator (Ralstonia eutropha), Alcaligenes latus, Pseudomonas spp., Comamonas spp. and other species. PHAs accumulation occurs in response to stress conditions, i.e. under high carbon and low nitrogen (24:1 ratio). PHA can be synthesized using recombinant microorganisms (provided with the operon phbA/phbB/phbC), escaping the constrains of nutrient request, except addition of high amount of sugar (glucose, lactose, fructose). In this study; E. coli was genetically modified for PHB production in biofermentors. The production of PHA at industrial scale requires a continuous supplementation of fermentable sugars to support the availability of nutrients and to assess the level of the exponential growth phase; since sugars are required either for bacterial growth either for PHA synthesis and energy storage. The biofermentors need to be run in automated system. Sensors are used at many points in fermentators; in the evaluation of parameters: consumption of sugars; cell density; quantification of PHB synthesis. The need of operational control during the fermentation has prompted us to application of three measurements; one unit linked to a Nanodrop to evaluate OD; one linked to a reaction chamber to measure sugars consumed by enzyme based fluorescence detection; and one for bacteria Nile Blue staining and fluorescence intensity reads. The growth of bacteria on three different plant by-products was monitored and PHB production in four days using a banana by-product feed was optimised. These detectors will make possible to exploit the full potential of bioreactors optimizing the time of use and maximizing the number of bacteria synthesizing PHA.

Text mining is a technological trend often highlighted in the continuous exchange of information through interconnected media. Its applicability goes beyond private organizations, as the public sector also requires it to treat textual information regarding services offered. Within this scenario, public security emerges as a prominent user of text mining that seeks to ensure the construction of data and knowledgebases to support decision-making about law enforcement actions to ensure citizen welfare. The primary objectives of this article are: (i) to develop a survey to identify text mining applications, techniques, opportunities, and challenges in public security, and (ii) to outline research directions concerning these topics and provide insights so that interested researchers can develop new studies. The literature was searched within four databases: Scopus, IEEE Xplore, ACM Digital Library, and Web of Science. A filtering process was applied to extract the works most aligned with the target theme, resulting in the selection of 194 of the most relevant works for a literature review. There were identified nineteen key applications of text mining related to public security and the most recurrent techniques and technologies reported between 2014 to 2021, supporting outlining three axes for future directions: one with possible expansion of objectives for new research; another on changes and adaptations in scopes for the methodological context; and the last one on expansions and changes in application scenarios based on the literature.

This study addresses the challenge of treating skin cancer effectively, especially in visible areas like the face, where traditional methods may be undesirable. Current options, including surgery and radiation therapy, have limitations such as complexity, expense, and imprecise dose delivery. The proposed solution involves additively manufacturing personalized patches using diagnostic imaging data, offering a targeted and controlled dose of beta-emitting isotopes like Y-90. The patches, tailored to the tumor's shape and depth, aim to minimize damage to healthy tissues and structures. Through 3D printing technology we demonstrated the feasibility of creating individualized applicators filled with radioisotopes, that have the potential to deliver therapeutic doses while ensuring patient comfort and affordability. This innovative approach, based on radiation delivery simulations, offers a promising future alternative to conventional radiation therapy methods. Clinical trials are required to validate its efficacy and safety, but the potential for reduced radiation exposure and enhanced treatment precision positions this personalized and targeted therapy as a valuable advancement in skin cancer treatment.

Polar stratospheric clouds (PSCs) form in polar regions typically between 15 and 25 km, when the local temperature is sufficiently low. PSCs play an important role in the ozone chemistry and the dehydration and denitrification of the stratosphere. Lidars with a depolarization channel may be used to detect and classify different classes of PSCs. The main PSC classes are water ice, nitric acid trihydrate (NAT) and supercooled ternary solutions (STS), the latter being liquid droplets consisting of water, nitric acid and sulphuric acid. PSCs have been observed at the lidar observatory at Concordia Station from 2014 on. The harsh environmental conditions at Concordia during winter render successful lidar operation difficult. In order to facilitate the operation of the observatory several measures have been put in place to achieve an almost complete remote control of the system. PSC occurrence is strongly correlated with local temperatures and is affected by dynamics, as the PSC coverage during the observation season shows.

Membrane-based sensors (MePSs) exhibit remarkable precision and sensitivity in detecting pressure changes. MePSs are commonly used to monitor catalytic reactions in solution, generating gas products crucial for signal amplification in bioassays. They also allow catalyst quantification by indirectly measuring the pressure generated by the gaseous products. This is particularly interesting to detect enzymes in biofluids associated with disease onset. To enhance the performance of a MePS, various structural factors influence membrane flexibility and response time, ultimately dictating the device's pressure sensitivity. In this study, we fabricated MePSs using polydimethylsiloxane (PDMS) and investigated how structural modifications affect the Young's modulus (E) and residual stress (σ0) of the membranes. These modifications have a direct impact on the sensors' sensitivity to pressure variations, observed as a function of the volume of the chamber (Σ) or of the mechanical properties of the membrane itself (S). MePSs exhibiting the highest sensitivities were then employed to detect catalyst quantities inducing the dismutation of hydrogen peroxide, producing dioxygen as gaseous product. As a result, catalase enzyme was successfully detected using these optimized MePSs, achieving a remarkable sensitivity of (22.7 ± 1.2) µm/nM and a limit of detection (LoD) of 396 pM.

Mandibular critical size defect (CSD) due to pathological conditions, trauma, and congenital disease can not heal spontaneously and predominantly filled with fibrous tissue. Therefore, a Guided Bone Regeneration (GBR) combined with bone grafting can be performed. The researchers considered using Demineralized Dentin Material Membrane (DDMM) from bovine dentine as an alternative GBR. This study aimed to determine the amount of fibroblast and collagen density after DDMM and bone graft implantation on CSD. Thirty-six Rattus norvegicus rats were used as samples. Mandibular bone defect 5x5 mm was made, then filled with bone graft and covered with Bovine Pericardium Collagen Membrane (BPCM) in the control group and DDMM in the treatment group. Six samples were sacrificed on 7, 14, and 21 days post-surgical for histology examination. There were no significant differences in the amount of fibroblast and collagen density (p-value > 0,05). The amount of fibroblast is lower and the collagen density is higher in treatment group. DDMM has microporosity to prevent connective tissue ingrowth and dentine tubules to allow growth factors release. DDMM and bone graft implantation can reduce the amount of fibroblasts and increase collagen density of CSD which potentially being used as a CSD alternative treatment for bone regeneration.

Active ageing is defined as the process of optimizing opportunities for physical, social and mental health to enable older people to take an active part in society without discrimination and to enjoy an independent and good quality of life. The World Health Organization assumed this as a process for increasing and maintaining an individual’s participation in activities to enhance his/her quality of life. In this survey, the authors addressed the following question: “Is assistive technology (AT) for mobility contributing to enhancement of lifelong capacity and performance?”. From June 2015 until February 2016, 96 community dwelling adults, AT users for mobility (powered wheelchairs, manual wheelchairs, lower limb prostheses, walkers, crutches and canes), aged 45-97, mean 67.02 +/- 14.24 years old, 56.3% female, were interviewed using the Psychosocial Impact of Assistive Devices Scale (P-PIADS), the Activities and Participation Profile related to Mobility (APPM) and demographics, clinical and questions about AT use and training. The participants’ profiles revealed moderate limitation and restrictions in participation, measured by the APPM (2.03). Most participants showed positive impact of AT; average scores obtained from the P-PIADS subscales were: Self-esteem 0.62, Competency 1.11 and Adaptability 1.10. P-PIADS total was 0.96, with the powered wheelchair users scoring the highest (1.53) and the walker users scoring the lowest (0.73). All subscales and P-PIADS total were positively correlated with the activities and participation profile. There was no relation between age and the psychosocial impact of AT or activities and participation profile. These results encourage the authors to follow these participants up for a lifelong intervention. To accomplish that aim, currently, the protocol is implemented at the AT prescribing centers in Coimbra, Portugal in order to assess the impact of AT on participation in society, one of the domains of the Active Ageing Index, a new analytical tool to help policy makers in developing policies for active and healthy ageing.

Since the creation of the first parallel electrical power systems around the world, the rotor angle stability of synchronously operating generators has been one of the most crucial and challenging problems. In modern electricity networks, involving Kazakhstani, where the renewable energy technologies are rapidly penetrating, and the issue of stability takes on even greater importance due to the technical shortcomings of inverter-based generation. In this framework, an analysis of rotor angle transient stability was carried out when replacing existing synchronous generators with doubly fed induction generators under a certain pre-emergency mode. A critical proportion of active power generation by DFIG units was identified at which transient stability can still be maintained due to the sufficient stored kinetic energy of the synchronous machines remaining in operation. In addition, 2 simple solutions were investigated to improve transient stability, such as an increased time of the automatic reclosure operation and the use of special load shedding automation. For the analysis, a real power system of Mangystau region in Kazakhstan was considered, and the PowerWorld software was used.

Biological membranes are fascinating. Santiago Ramón y Cajal, who received the Nobel prize in 1906 together with Camillo Golgi for their work on the nervous system, wrote “[..]in the study of this membrane[..] I felt more profoundly than in any other subject of study the shuddering sensation of the unfathomable mystery of life”[1]. The visualization and conceptualization of these biological objects have profoundly shaped many aspects of modern biology, drawing inspiration from experiments, computer simulations, as well as from the imagination of scientists and artists. The aim of this review is to provide a fresh look on current ideas of biological membrane organization and dynamics by discussing selected examples across fields [1] The full quotation is “I must not conceal the fact that in the study of this membrane I for the first time felt my faith in Darwinism (hypothesis of natural selection) weakened, being amazed and confounded by the supreme constructive ingenuity revealed not only in the retina and in the dioptric apparatus of the vertebrates but even in the meanest insect eye. There, in fine, I felt more profoundly than in any other subject of study the shuddering sensation of the unfathomable mystery of life.” from the autobiography Recollections of My Life.

The most common and taught membrane theory assumes that the membrane behaves as a kind of electrical capacitance that is exposed to an electrical current generated by an ionic flow. If this statement is verifiable, it can be confirmed by the laws of physics, mathematics and in particular electricity. We will demonstrate that this hypothesis is not verified and that it is necessary to modify biophysics according to already established and experimentally verified principles of physics.

The construction industry is a resource and energy intensive industry and thus, has been criti-cized due to rising environmental concerns. As a result of that it has gained heightened interest in the concept of Circular Economy (CE) over the last decade to its ability to promote the slowing, reducing, and closing production and consumption cycles of materials and products used in the construction practices. Digital technologies hold potential to enhance the construction industry's ability to integrate the concept of CE in its practices. However, a clear understanding of digital technology (DT) related barriers that hinder practical implementation of CE, appears to be lacking within the sector. In light of this, this study aims to identify the barriers to adopting DTs to im-plement CE practices in the construction industry. To achieve this aim, a systematic literature review was conducted by reviewing twenty-three (23) relevant papers published until January 2024 in Scopus database. The VOS viewer software was used to perform a co-occurrence analysis of keywords to identify new and popular study areas in the field and content analysis was used to analyse the major barriers to adapt DTs to implement CE in the construction industry. The study identified thirty-four (34) barriers to use DTs to implement CE and these were categorized into nine areas such as: infrastructure, organizational, regulatory, standardization, investment, nature of the construction industry, technological, stakeholder and data related barriers. These findings will be beneficial for construction practitioners and policy makers to adopt DTs to integrate CE practices in the construction industry.

The main characteristics of blockchains, such as security and traceability, have enabled their use in many distinct scenarios, such as the rise of new cryptocurrencies and decentralized applications (dApps). However, part of the information exchanged with the typical blockchains is public, which can lead to privacy issues. To avoid or mitigate these issues, some blockchains are applying mechanisms to deal with data privacy. Trusted Execution Environments, the basis of confidential computing, and secure Multi-party Computation are two technologies that can be applied in that sense. In this paper, we analyzed seven blockchain technologies that apply mechanisms to improve data privacy. We defined seven technical questions related to common requirements for decentralized applications and, to answer each question, we reviewed the available documentation and gathered information from chat channels. We briefly present each blockchain technology and the answers to each technical question. Finally, we present a table summarizing the information and showing which technologies are more prominent.

In the last 20 years, an increasing number of studies have been reported on membrane active peptides, which exert their biological activity by interacting with the cell membrane either to disrupt it and lead to cell lysis or to translocate through it to deliver cargos into the cell and reach their target. These peptides are attractive alternatives to currently used pharmaceuticals. Antimicrobial peptides (AMPs) and peptides designed for drug and gene delivery currently in the drug pipeline suggest that these membrane active peptides will soon constitute a significant percentage of the drug market. Here, we focus on two most prominent classes of membrane active peptides; AMPs and cell-penetrating peptides (CPPs). AMPs are a group of membrane active peptides that disrupt the membrane integrity or inhibit the cellular functions of bacteria, virus and fungi. CPPs are another group of membrane active peptides that mainly function as cargo-carriers even though they may also show antimicrobial activity to some extent. Biophysical techniques to understand how they interact with the membrane have shed light on the peptide–membrane interaction at various levels of detail. Structural investigation of membrane active peptides in the presence of the membrane provides important clues on the effect of the membrane environment on peptide conformations. Advances in live imaging techniques have allowed examination of peptide action at a single cell or single molecule level. In addition to these experimental biophysical techniques, molecular dynamics simulations provided clues on the peptide-lipid interactions and dynamics of the cell entry process at atomic detail. In this review, we summarize the recent advances in experimental and computational investigation of membrane active peptides with particular emphasis on two amphipathic membrane active peptides, the AMP melittin and the CPP pVEC.

The generation and maintenance of membrane potential is a fundamental part of Membrane Pump Theory. One of the key points of this hypothesis is based on a natural or facilitated molecular diffusion through several types of ion channels and pumps like the Na/K ATPase. Chemistry, physics and especially electrochemistry, however, bring strong contradictions to this theoretical assumption. By respecting the principles of chemistry and electrostatics, it becomes obvious that this theoretical hypothesis cannot work. The ionic diffusion that would be at the origin of this potential cannot take place. Indeed, the topology and the forces involved definitively exclude the current model, which must absolutely be revised according to the current state of our knowledge and allow an advance in the understanding of the phenomena and open new research perspectives.

The exploitation of lipid membranes in biosensors has provided the ability to reconstitute a considerable part of their functionality to detect trace of food toxicants and environmental pollutants. Nanotechnology enabled sensor miniaturization and extended the range of biological moieties that could be immobilized within a lipid bilayer device. This chapter reviews recent progress in biosensor technologies based on lipid membranes suitable for environmental applications and food quality monitoring. Numerous biosensing applications are presented, putting emphasis on novel systems, new sensing techniques and nanotechnology-based transduction schemes. The range of analytes that can be currently detected include, insecticides, pesticides, herbicides, metals, toxins, antibiotics, microorganisms, hormones, dioxins, etc. Technology limitations and future prospects are discussed, focused on the evaluation/ validation and eventually commercialization of the proposed sensors.

In order to alter and adjust the shape of the membrane, cells harness various mechanisms of curvature generation. Many of these curvature generation mechanisms rely on the interactions between peripheral membrane proteins, integral membrane proteins, and lipids in the bilayer membrane. One of the challenges in modeling these processes is identifying the suitable constitutive relationships that describe the membrane free energy that includes protein distribution and curvature generation capability. Here, we review some of the commonly used continuum elastic membrane models that have been developed for this purpose and discuss their applications. Finally, we address some fundamental challenges that future theoretical methods need to overcome in order to push the boundaries of current model applications.

The exploitation of lipid membranes in biosensors has provided the ability to reconstitute a considerable part of their functionality to detect trace of food toxicants and environmental pollutants. Nanotechnology enabled sensor miniaturization and extended the range of biological moieties that could be immobilized within a lipid bilayer device. This chapter reviews recent progress in biosensor technologies based on lipid membranes suitable for environmental applications and food quality monitoring. Numerous biosensing applications are presented, putting emphasis on novel systems, new sensing techniques and nanotechnology-based transduction schemes. The range of analytes that can be currently detected include, insecticides, pesticides, herbicides, metals, toxins, antibiotics, microorganisms, hormones, dioxins, etc. Technology limitations and future prospects are discussed, focused on the evaluation/ validation and eventually commercialization of the proposed sensors.

Axial resolution is one of the most important characteristics of a microscope. In all microscopes, a high axial resolution is desired in order to discriminate information efficiently along the longitudinal direction. However, when studying thick samples that do not contain laterally overlapping information, a low axial resolution is desirable as information from multiple planes can be recorded simultaneously from a single camera shot instead of plane-by-plane mechanical refocusing. In this study, we increased the focal depth of an infrared microscope non-invasively by introducing a binary axicon fabricated on barium fluoride substrate close to the sample. Preliminary results of imaging thick and sparse silk fibers showed an improved focal depth with a slight decrease in lateral resolution and increase in background noise.

This analysis takes into account a significant chapter of the history of elites and eugenics from Transylvania during the interwar period. In his famous „Black Notebook”, Alexandru Vaida-Voevod, one of the most important personalities of the Romanian Great Union generation, wrote some surprising reflections about eugenics, race, and Romanian national superiority. In different ways, his reflections underline an invitation to analyze Romanian elites from the interwar period, as well as their way of thinking and feeling. Vaida's "Black Notebook" can therefore be considered "a torn page" from an important chapter in the history of the Romanian eugenics movement. It also represents an important key for understanding the history of Romanian freemasonry in Transylvania from the first two decades of the 20th century.

The mHealth is a term that is used for mobile health supported by smart devices such as mobile phones, tablets, and wearable smart devices, etc. The smart devices strengthen the efficiency and effectiveness of interaction with patients, physicians, and specialists. Patients nowadays would like to be intimately involved in their diagnosis as well as to make more informed decisions concerning their care. It has begun to measure the success of the quality of treatment. This was a reason that patients trust mHealth to provide them with consistency in their communications with the physicians. Most wireless strategies do not measure up to this standard so that patient engagement ultimately ended up decreasing. The blockchain can boost mHealth through storing and sharing electronic data securely and transparently. It can enhance the accessibility of patient information in real-time. The Internet of Things (IoT) provides a unique identification number to every connected device such as mobile devices, medical devices, and wearable devices. This framework uses the blockchain and IoT technologies together to provide quick help to the patients, monitor remotely, reduce the cost and unnecessarily hospitalization physically and find the real diagnosis. In order to increase patient involvement, mHealth framework with blockchain and IoT technologies has built with the key objective of providing patients with full information on their treatment and diagnosis.

Web-Based GIS is a platform that deals with the representation, management and storage of locational information for real-time online retrieval, viewing and manipulations. Web-based GIS incorporate all the functions of information systems: gathering, storing, retrieving, visualizing and dissemination of spatial information on the Internet. In modern-day GIS serve as vital means to not only geo-referenced locational information that are been retrieved but also the development in web-based technologies as well as there involvements in decision making processes. In recent time the increased used of GIS on the Internet have totally transformed and made three distinct changes across our GIS environment. These are: (i) how are GIS data being accessed (ii) what are modes of its transmission and (iii) what available GIS functionalities are within the environment for analysis. This paper examines the applications and technologies associated with web-based GIS architectures with an emphasis on the internet GIS based structure and case studies of GIS Web-based applications in MapInfo, Microsoft Silverlight Technology and the ArcGIS Server using ArcGIS JavaScript API.

This study concerns the transport and retention of polydisperse micron-sized (16 ± 6 µm) of microplastics (MPls) in porous media under varying flow rate conditions. Sorption kinetics were modeled using first-order reversible and irreversible kinetic sorption models, with sensitivity analyses providing insights into each sorption parameter's effect. Both numerical modeling and experimental measurements were employed to assess sand filter retention rates. The impact of flow rate on sorption reveals variations in distribution coefficient (Kd), mass transfer coefficient (β), and irreversible sorption rate (K1). Lower flow rates are correlated with higher Kd and β values, indicating an increase in sorption and diminished mass transfer rates. The findings revealed that an increase in Kd resulted in a more gradual sorption process with a decrease in peak concentration, whereas changes in β influenced the rate of sorption and peak concentration to a lesser extent compared to Kd. Lower K1 values are associated with higher peak concentrations and decreased retention efficiency. Retention rates were evaluated by a numerical model and found as 28 ± 1% at a flow rate of 31 ml min⁻¹ and 17 ± 1% at 65 ml min⁻¹. The introduction of MPls into soil environments has been noted to modify transport dynamics into soil. As a result, these alterations effects hydrological characteristics of soil, thereby impacting quality of groundwater and agricultural output. The mean absolute error (MAE) of 6% between modeled and observed retention rates suggests minor discrepancies. This study highlights the importance of examining retention efficiency and the accuracy of numerical models in porous media during MPl transport.

Environmental degradation leads to a totally unsustainable food system. In addition to this is-sue, the consumption of foods that improve people's health and well-being is recommend-ed. These guidelines create new challenges and the demand for alternatives to meet these needs in the short term. One of the alternatives is undoubtedly the use of by-products of winemaking, namely in the form of grape pomace flour (GPF), which is obtained in a totally sustainable way, requires no further water consumption or agricultural land, and is an ingredient that boasts all the characteristics that meet the circular economy and has colossal potential in promoting nutrition and healthy eating. To verify the benefits of using the Touriga Nacional and Arinto (Vitis vinifera L.) flour varieties, analytical determinations were made to identify and quantify different components, such as nitrogen and extractable phosphorus, ash, moisture, proteins, fats, dietary fibers, total sugars, and phenolic content. GPF could become a valuable ingredient due to its nutritional quality and high content in various polyphenols namely flavonoids and pyranoanthocyanins.

Manufacturing of facial epithesis is a complex technological process including several traditional stages of production, accompanied by aggravated psycho-emotional status of the patient. One of the main factors causing discomfort in patients with facial defects is the process of obtaining silicone impressions from the wound surface and the long waiting period for the final epithesis. Active development of digital technologies in medicine and dentistry helps specialists not only to automate most of the traditional stages of manufacturing of dento-mandibular and facial prostheses, but also improves the quality of life of patients by increasing the efficiency of services and reducing the production time of prosthetic structures. The application of digital technologies in the production of facial epithesis was difficult due to the lack of specialized 3D-software for modeling and material for further additive manufacturing of structures. The authors developed a unique technology for 3D modeling and additive manufacturing of facial epithesis, including a 3D CAD module and material for 3D printing. The primary objective was to fabricate immediate facial prostheses in the postoperative period in the shortest possible time until the final epithesis was fabricated.

Hepatocellular carcinoma (HCC) is a heterogeneous malignancy with complex carcinogenesis. Although there has been significant progress in the treatment of HCC over the past decades, drug resistance to chemotherapy remains a major obstacle in its successful management. In this study we were able to reduce chemoresistance in cisplatin-resistant HepG2 cells by either silencing the expression of transglutaminase type 2 (TG2) using siRNA or by pre-treatment of cells with the TG2 enzyme inhibitor cystamine. Further analysis revealed that, whereas the full-length TG2 isoform (TG2-L) was almost completely cytoplasmic in its distribution, the majority of the short TG2 isoform (TG2-S) was membrane-associated in both parental and chemoresistant HepG2 cells. Following induction of cisplatin toxicity in non-chemoresistant parental cells, TG2-S together with cisplatin quickly relocated to the cytosolic fraction. Conversely, no cytosolic relocalisation of TG2-S or nuclear accumulation cisplatin was observed following identical treatment of chemoresistant cells, where TG2-S remained predominantly membrane-associated. This suggests that deficient subcellular relocalisation of TG2-S from membranous structures into the cytoplasm may limit the apoptic response to cisplatin toxicity in chemoresistant cells. Structural analysis of TG2 revealed the presence of binding motifs for interaction of TG-S with the membrane scaffold protein LC3/LC3 homologue that could contribute to a novel mechanism of chemotherapeutic resistance in HepG2 cells.

The generation and maintenance of membrane potential is considered a fundamental element of the cellular machinery. They are based on elements of physics and chemistry. Mathematics is used to validate the equations and evaluate the results. However, this computation process can lead to a misunderstanding of the phenomena involved or to the masking of crucial events. It is even possible that the calculation no longer corresponds to the hypothesis considered. Membrane theory is no exception to these trivial considerations, which are essential for normal theory validation.

Membrane potential generation and maintenance are fundamental parts of membrane theory. However, since its inception, theories and assumptions have remained simple, whereas the amount of knowledge available has only grown. Unfortunately, this simplification and reductionism lead to its loss of validity on both microscopic and macroscopic scales. This article shows that assumptions made outside the context of factual reality lead to contradictions that cannot be compared with science. Membrane theory must be thoroughly revised, taking into account all forgotten and unanswered assumptions and questions to conform to facts and science to maintain credibility.

The membrane potential or resting potential of the neuron has been the subject of many studies. Although this theory explains the generation and maintenance of the membrane potential by direct or even facilitated diffusion, there are too many contradictions to doubt that these forces are sufficient or even at work in a process whose initial conditions are of rare complexity. The aim of this article is to show that already in the past, a competing theory has been developed whose hypothesis seems more scientifically sound. To confirm this last theory, Hirohisa Tamagawa carried out an experiment of great simplicity which makes it possible to invalidate the current theory and to question the teaching and the knowledge in Biology and Biophysics.

There are different treatment options in modern dentistry for the replacement of lost dentition. Of these the most upcoming and acceptable treatment option is Dental implants. The common problem usually with immediate implant placement in the anterior region is the post-operative soft tissue contour as a part of the bone modelling during healing. Hurzeler et al in 2010 introduced a new technique called the “socket shield technique”. This technique has been used as an alternative treatment modality for immediate implant placement in the aesthetic zone.This review articles provides a detailed information regarding the clinical concept of Root membrane technique.

In contemporary science and technology, photonic sensors are essential. They may be made to be extremely resistant to some physical parameters while also being extremely sensitive to other physical variables. Most photonic sensors may be incorporated on chips and operate with CMOS technology, making them suitable for use as extremely sensitive, compact, and affordable sensors. Photonic sensors can detect electromagnetic (EM) wave changes and convert them into an electric signal due to the photoelectric effect. Depending on the requirements, scientists have found ways to develop photonic sensors based on several interesting platforms. In this work, we extensively reviewed the most generally utilized photonic sensors for detecting vital environmental parameters and personal healthcare. These sensing systems include optical waveguides, optical fibers, plasmonics, metasurfaces, and photonic crystals. Various aspects of light are used to investigate photonic sensors' transmission or reflection spectra. In general, resonant cavity or grating-based sensor configurations that work on wavelength interrogation methods are preferred, so these sensor types are mostly presented. We believe this paper will provide insight into the novel types of available photonic sensors.

With Internet of Things (IoT) gaining presence throughout different industries a lot of new technologies have been introduced to support this undertaking. Implications on one such technology, wireless systems allowed for the use of different communication methods to achieve the goal of transferring data reliably, with more cost efficiency and over longer distances. Anywhere from a single house with only a few IoT devices such as a smart light bulb or a smart thermostat connected to the network, all the way to a complex system that can control power grids throughout countries, IoT has been becoming a necessity in everyday lives. This paper presents an overview of the devices, systems and wireless technologies used in different IoT architectures (Healthcare, Vehicular Networks, Mining, Learning, Energy, Smart Cities, Behaviors and Decision Making), their upbringings and challenges to this date and some foreseen in the future.

Because of the near-term risk of extreme weather events and other adverse consequences from climate change, and, at least in the longer term, global fossil fuel depletion, there is world-wide interest in shifting to noncarbon energy sources, especially renewable energy (RE). Because of possible limitations on conventional renewable energy sources, researchers have looked for ways of overcoming these shortcomings by introducing radically new energy technologies. The largest RE source today is bioenergy, while solar energy and wind energy are regarded as having the largest technical potential. This paper reviews the literature on proposed new technologies for each of these three RE sources: microalgae for bioenergy, photolysis and airborne wind turbines. The main finding is that their proponents have underestimated the difficulties facing their introduction on a very large scale.

This paper evaluates the potential of solar concentration technologies—compound parabolic collector (CPC), linear Fresnel collector (LFC) and parabolic trough collector (PTC)—as an alternative to conventional sources of energy for industrial processes in Latin America, where high levels of solar radiation and isolated areas without energy supply exist. The analysis is addressed from energy, economic and environmental perspective. A specific application for Argentina in which fourteen locations are analyzed is considered. Results show that solar concentration technologies can be an economically and environmentally viable alternative. Levelized cost of energy (LCOE) ranges between 2.5 and 16.9 c€/kWh/m² and greenhouse gas (GHG) emissions avoided range between 33 and 348 kgCO₂/(m²·year). CPC technology stands out as the most recommendable technology when the working fluid temperature ranges from 373K to 423K. As the working fluid temperature increases the differences between the LCOE values of the CPC and LFC technologies decrease. When 523K is reached LFC technology is the one which presents the lowest LCOE values for all analyzed sites, while the LCOE values of PTC technology are close to CPC technology values. Results show that solar concentration technologies have reached economic and environmental competitiveness levels under certain scenarios, mainly linked to solar resource available, thermal level requirements and solar technology cost.

Endothelial cells are the crucial inner lining of blood vessels, pivotal in vascular homeostasis and integrity. However, these cells are perpetually subjected to a myriad of mechanical, chemical, and biological stresses that can compromise their plasma membranes. A sophisticated repair system involving key molecules, such as calcium, annexins, dysferlin, and MG53, is essential for maintaining endothelial viability. These components orchestrate complex mechanisms, including exocytosis and endocytosis, to repair membrane disruptions. Dysfunctions in this repair machinery, often exacerbated by aging, are linked to endothelial cell death, subsequently contributing to the onset of atherosclerosis and the progression of cardiovascular diseases (CVD) and stroke, major causes of mortality in the United States. Thus, identifying the core machinery for endothelial cell membrane repair is critically important for understanding the pathogenesis of CVD and stroke and developing novel therapeutic strategies for combating CVD and stroke. This review summarizes the recent advances in understanding the mechanisms of endothelial cell membrane repair. The future directions of this research area are also highlighted.

The structure of existing activated models is inherently deficient in reflecting the major role of the membrane filtration. This study developed and proposed a novel model, MASM, for the membrane activated process. The effective filtration size imposed by the membrane module, entrapping larger size particles was adopted as the basis of the proposed model. The model defined a modified COD fractionation, accounting for the captured COD fractions as additional model components and utilizing related mass balance relationships. It was implemented for testing the fate of soluble hydrolysable COD and system performance of super-fast membrane activated sludge based on real data for the characterization and process kinetics of domestic sewage and denim processing effluents. Model evaluation was carried for parallel systems with gravity settling and membrane filtration operated at a sludge age range of 0.5-2.0 d. Results reflected significantly better performance of super-fast membrane activated sludge system for both wastewaters, underlining that it was crucially important to account for the captured COD fractions to provide an accurate evaluation of system behavior and effluent quality. This should also be identified as the major shortcoming of the ASM models for evaluating and predicting system performance of activated sludge configurations with membrane separation.

As both governments and customers push for sustainable and recyclable textile products, textile companies will have to change their linear business model to a circular one. The aim of the present work is to help these companies take action by providing an update of the state-of-the-art of textile recycling technologies. Extensive desktop research was performed in order to prepare an overview of existing textile recycling technologies, their current state and prognosis, including also facilitating technologies for sorting and disintegration of textile products as well as virtual platforms that connect stakeholders and inform consumers.

Security in IoT systems is extremely important, as an intrusion into an IoT device or network can affect not only our domestic lives, but also industrial assets, with the potential to cause enormous damage. We discuss IoT security issues as defined by the OWASP Foundation, focusing on network related aspects. After a brief description of SDN in general and OpenFlow in particular, we discuss how SDN technologies can greatly help in designing and deploying more secure IoT networks by enhancing the cryptographic capabilities of devices, isolating devices or networks, blocking access to unwanted services, redirecting traffic to deep inspection systems, monitoring packet flows and devices, etc. These capabilities can be implemented using open-source OpenFlow controllers such as Faucet.

(1) Introduction: The COVID-19 pandemic presented unique challenges for patients and healthcare providers, especially for those working with obesity and related health problems. E-health has emerged as a crucial tool for the follow-up of users undergoing bariatric surgery during this period, allowing remote monitoring of users' health status and providing access to virtual consultation with health professionals. This study aims to analyze the impact of the use of telemedicine during the COVID-19 pandemic on the results of bariatric surgery and user satisfac-tion with this follow-up. (2) Method: Observational study with retrospective data collection. The variables were divided into several groups: health data, associated comorbidities, quality of life, quality of sleep and satisfaction with telemedicine monitoring. (3) Results: Surgery significantly affected weight loss, in general more than 75% loss of excess weight. Comorbidities, like the qual-ity of life, were reversed over time, with 50% of subjects maintaining excellent levels. Although most users were satisfied with the monitoring, the variables had no relationship. (4) Conclusions: The follow-up assured by telemedicine did not alter the results of bariatric surgery, which may allow us to infer that it may be an option to consider for regular monitoring of the post-bariatric surgery process.

A simple model is developed for membrane fouling, taking into account two main fouling phenomena: cake formation, due to attached solids onto the membrane surface and pores clogging, due to retained compounds inside the pores. The model is coupled with a simple anaerobic digestion model for describing the dynamics of an Anaerobic Membrane BioReactor (AnMBR). In simulations, we investigate its qualitative behavior: it is shown that the model exhibits satisfying properties in terms of flux decrease due to membrane fouling. Comparing simulation and experimental data, the model is shown to predict quite well the dynamics of an AnMBR. The simulated flux best fits the experimental flux with a correlation coefficient r2=0.968 for the calibration data set and r2=0.938 for the validation data set. General discussions are given on possible control strategies to limit fouling and optimize the flux production. We show in simulations that these strategies allow one to increase the mean production flux to 33 L/(h.m2), whereas without control it was 18 L/(h.m2).

Purpose: National Institute for Health and Care Excellence (NICE) has recently published quality standards for assessment of fall risk and preventing further falls. According to the standards, multifactorial fall risk assessments should include: identification of falls history; analysis of gait, balance, mobility and muscle strength, among other factors. Despite being based on subjective analysis or simple timing and not being multifactorial, physiotherapists and physicians quite often use these tests as reference scales to differentiate between lower and higher risk of falling. Instrumented TUG has been recently reported to provide important additional information to the overall score. Objective: To explore a case-based approach of fall risk assessment to identify the most relevant and informative risk factors that in combination could better define a person risk profile. Materials and Methods: A multifactorial assessment of fall risk through questionnaires, standard functional tests, tests instrumented with inertial sensors, and force platforms has been studied within a group aged 55-80 years old. Different fall risk factors and fall risk assessment methods were analyzed in a case-based descriptive study. Results & Discussion: Subjects at higher risk of falling were identified based on their detailed profiles. A set of features were obtained from the instrumented standard tests differing significantly between subjects presenting higher or lower fall risk. Therefore, instrumenting conventional tests with wearables containing inertial sensors and force platforms gives more detailed and quantitative insights. This information can be used to better define and tailor fall prevention exercises and to improve the follow-up of the evolution of the subject.

In the rapidly evolving landscape of wireless communication, each successive generation of networks has achieved significant technological leaps, profoundly transforming the way we connect and interact. From the analog simplicity of 1G to the digital prowess of 5G, the journey of mobile networks has been marked by constant innovation and escalating demands for faster, more reliable, and more efficient communication systems. As 5G becomes a global reality, laying the foundation for an interconnected world, the quest for even more advanced networks leads us to the threshold of the sixth-generation (6G) era. This paper presents a hierarchical exploration of 6G networks, poised at the forefront of the next revolution in mobile wireless technology. This study delves into the technological advancements that underpin the need for 6G, examining its key features, benefits, and the key enabling technologies. We dissect the intricacies of cutting-edge innovations like terahertz communication, ultra-massive MIMO, artificial intelligence (AI), machine learning, quantum communication, and re-configurable intelligent surfaces. Through a meticulous analysis, we evaluate the strengths, weaknesses, and state-of-the-art research in these areas, offering a wider view of the current progress and potential applications of 6G networks. Central to our discussion is the transformative role of AI in shaping the future of 6G networks. By integrating AI and machine learning, 6G networks are expected to offer unprecedented capabilities, from enhanced mobile broadband to groundbreaking applications in areas like smart cities and autonomous systems. This integration heralds a new era of intelligent, self-optimizing networks that promise to redefine the parameters of connectivity and digital interaction. This paper also addresses critical challenges in the deployment of 6G, from technological hurdles to regulatory concerns, providing a holistic assessment of potential barriers. By highlighting the interplay between 6G and AI technologies, this study not only maps out the current landscape but also lights the path forward in this rapidly evolving domain. This paper aims to be a cornerstone resource, providing essential insights, addressing unresolved research questions, and stimulating further investigation into the multifaceted realm of 6G networks. By highlighting the synergy between 6G and AI(Artificial Intelligence) technologies, we aim to illuminate the path forward in this rapidly evolving field.

The need for industrial and commercial machinery to maintain high torque while accurately following a variable angular speed is increasing. To meet this demand, induction motors (IMs) are commonly used with variable speed drives (VSDs) that employ a field-oriented control (FOC) scheme. Over the last thirty years, IMs have been replacing independent connection direct current motors due to their cost-effectiveness, reduced maintenance needs, and increased efficiency. However, IMs and VSDs exhibit nonlinear behavior, uncertainties, and disturbances. This paper proposes a robust combined adaptive passivity-based control (CAPBC) for this class of nonlinear systems that applies to angular rotor speed and stator current regulation inside an FOC scheme for IMs´ VSDs. It uses general Lyapunov-based design energy functions and adaptive laws with σ-modification to assure robustness after combining control and monitoring variables. Lyapunov’s second method and Barbalat Lemma prove that the control and identification error tends to be zero over time. Moreover, comparative experimental results with standard Proportional Integer controller (PIC) and direct APBC, show the proposed CAPBC effectiveness and robustness under normal and changing conditions

Extracorporeal membrane oxygenation (ECMO) is used for the management of severe respiratory and cardiac failure, as well as bridge to definite treatment or transplantation. ECMO associated coagulopathy (EAC) is a frequent complication leading to high rates of thrombosis or severe haemorrhage, contributing to morbidity and mortality of patients. Understanding the pathophysiology of EAC is substantial for effectively managing patients on ECMO. We analyse the underlying mechanism of EAC and discuss the monitoring of coagulation profile, combining the viscoelastic point of care assays with the conventional coagulation laboratory tests.

Environment pollution is the major problem for all the sectors. In environment pollution there are different types of pollution is included such as air pollution, water pollution, soil pollution etc. In these types of pollution most of it is air pollution. There are many reasons for pollution of air. Human advance in science but one of the major draw backs of science is the pollution of air rapidly. Air pollution is injurious to health. Every year a large number of people died for the effects of air pollution. It can be improved in many ways among these ways technology upgradation plays a major role here. There are various method that prevent air pollution. Many researchers tried and is trying to prevent the air pollution in many ways. In this review paper I summarise the existing research on different ways for preventing air pollution in addition I will discuss the gaps and future aspect on this topic.