We extend the concept of metallic ratios to the real argument n considered as a dimension by analytic continuation showing that they are defined by an argument of a normalized complex number, and for rational n ≠ {0, ±2}, they are defined by Pythagorean triples. We further extend the concept of metallic ratios to metallic angles.

A new Mg-Zn-Zr-Ca alloy in powder state was obtained via mechanical alloying method, from pure elemental powder. Further, the obtained powder-alloy was processed by selective laser melting (SLM) procedure to obtain 3D printed samples for small biodegradable implants. A series of microstructural, mechanical and corrosion analysis were performed. The SEM analysis of powder-alloy reveal a good dimensional homogeneity, with uniform colored, no agglutinated and almost rounded particles, suitable for selective laser melting procedure. Further, the SLM samples reveal a robust and unbreakable morphology, with a suitable porosity and without undesirable balling effect. The tested Young’s modulus of the SLM samples, of 42 GPa, is close to cortical bone one, of 30 GPa. The corrosion tests performed in PBS (Phosphate-buffered saline) solution show that the corrosion parameters have a satisfactory evolution.

The production of a ton of steel in an integrated steel plant generates of approximately 1 ton of ferrous slag. A great part of ferrous slags is recycled in civil and road construction etc., but a huge amount is still dumped. Recycling ferrous slag as cement precursor was considered the upcycling route. Regulation (EU) 2024/1252 requires the Member States to provide information, until November 2026, on the critical raw materials (CRM) amount in their secondary resources and on quantification methods used for. This study addresses two synergic objectives: ensuring the reliability of XRFS results and screening for CRM in ferrous slags based on XRFS outcomes. The main novelty of the paper is the way of ensuring the reliability of the XRFS results based on weighted arithmetic mean and on the maximum likelihood approach. Secondly, the XRFS measurements carried on ferrous slags demonstrate that they contain significant amounts of CRM like Ba, Sr, Y, etc. XRFS cannot detect light CRM. Our preliminary LIBS measurements on ferrous slags disclosed the presence of Li and Be. The drawbacks of the XRFS technique impose further research to develop an integrated XRFS, LIBS and XRD procedure for comprehensive and trustworthy CRM screening in extractive waste piles.

The European Green Deal poses a two-pronged challenge for the automotive industry: migrating to solutions based in light structures, requiring light weight concepts and light materials, while at the same time avoiding dependence towards the importation of these advanced materials. Aluminium alloys are lightweight and cost-effective materials that can successfully cover the requirements of many structural applications, however their production requires from bauxite and other Critical Raw Materials (CRM), such as Si and Mg. Aluminium alloys are fully recyclable, but scrap is usually contaminated and its use is related to an increment of impurities, tramp element and undesired inclusions. Traditionally, the use of secondary alloys has been restricted to low performance applications. The present work analyses the effect that the use of scrap has in the quantity of inclusions present in the alloy and in other properties relevant for the material processing. The study was carried out for common alloys belonging to 3 of the most common aluminium processes used in the car manufacturing industry: High Pressure Die Casting (HPDC) (EN AC-43500), extrusion (6063) and sheet metal forming (5754 and 6181). Reference alloy were mixed with different level of scrap (0, 20, 40, 60, 80 and 100%) trying to keep the chemical composition as unaffected as possible. The inclusions level of the alloy was characterized with the Prefil Foot-printer® test. In addition, the obtained materials, after being cast in an open mould, were subjected to metallographic characterization. Relevant properties to assess the formability quality of the alloys for the corresponding transforming process, were obtained: flowability test for HPDC alloy and high temperature compression for extrusion alloys. The results obtained suggest that the number of inclusions present in the melt highly increase with the amount of scrap used to produce the alloy. These inclusions are also related with an important lost of flowability, but do not have a noticeable impact on microstructure.

Among magnetoelectric (ME) heterostructures, ME laminates of the type Metglas-like / PVDF (magnetostrictive+piezoelectric constituents) have shown the highest induced ME voltages, usually detected at the magnetoelastic resonance of the magnetostrictive constituent. This ME coupling happens because of the high cross-correlation coupling between magnetostrictive and piezoelectric material, and is usually associated with a promising application scenario for sensors or actuators. In this work we detail the basis of the operation of such devices, as well as some arising questions (as size effects) concerning their best performance. Also, some examples of their use as very sensitive magnetic fields sensors or innovative energy harvesting devices will be presented At the end, the challenges, future perspectives and technical difficulties that will determine the success of ME composites for sensor applications are discussed.

This research presents a novel algorithmic implementation to improve the analysis of visually controlled interception and accompanying motor action through the computational application of harmonic ratios and stimulation invariants. Unlike traditional models that focus mainly on psychological aspects, our approach integrates the relevant constructs into a practical mathematical framework. This allows for dynamic prediction of interception points with improved accuracy and real-time perception-action capabilities, essential for applications in neurorehabilitation and virtual reality. Our methodology uses stimulation invariants as key parameters within a mathematical model to quantitatively predict and improve interception outcomes. The results demonstrate the superior performance of our algorithms over conventional methods, confirming their potential for ad-vancing robotic vision systems and adaptive virtual environments. By translating complex theo-ries of visual perception into algorithmic solutions, this study provides innovative ways to im-prove motion perception and interactive systems. This study aims to articulate the complex inter-play of geometry, perception, and technology in understanding and utilizing cross-ratios at infin-ity, emphasizing their practical applications in virtual and augmented reality settings.

Due to the extraordinary mechanical properties of ultra-high-performance concrete (UHPC), the shear stirrups in UHPC beams could potentially be removed. The aim of this study is to determine the effect of beam height and steel fiber volume content on the shear behavior of non-stirrup UHPC beams under a larger shear span-depth ratio (up to 2.8). Eight beams were designed and fabricated, including six non-stirrup UHPC beams and two comparing stirrup-reinforced normal concrete (NC) beams. The experimental results demonstrated that the volume content of steel fiber could be a crucial factor affecting the ductility, cracking strength, and shear strength of non-stirrup UHPC beams and altering their failure modes. Additionally, the height of the beam had a considerable effect on its shear resistance. This study revealed that the French standard formulae were more accurate for the UHPC beams with larger shear span-depth ratios and PCI-2021 formulae greatly overestimate the shear capacity of UHPC beams with larger shear span-depth ratios. Xu’s formulae were more accurate for the steel fiber-reinforced UHPC beams with larger shear span-depth ratios.

Process parameters influencing mechanical properties have always been a critical area of research for quite some time. We investigated the effect of laser power and laser scan velocity on the impact strength and maximum stress of 3D-printed metallic specimens of steel 1.2709 and 1.4542. Laser power significantly affected the impact strength and maximum stress of both the steels. With the increase in laser power, the impact strength increased for 1.2709 steel. However, there was a little increase in the impact strength with increasing laser power in the case of 1.4542 steel. Laser power had a decreasing impact on the maximum stress for 1.2709 steel. For 1.4542, maximum stress increased with increasing laser power, but then gradually declined. We observed that using laser power beyond 350W led to printing defect in the specimens, as maximum stress for some specimens reached close to zero in the case of 1.4542 steel. Laser scan velocity had a strong declining effect on the impact strength of 1.2709 steel.

In the present work, a portable device system applied in the detection and classification of different metallic ions was proposed and developed, aiming at its application in the monitoring of hydrological systems like rivers, lakes and groundwater. Considering the system features, a portable colorimetric system was developed by using a multispectral optoelectronic sensor. All the technology of quantification and classification of metallic ions using Optoelectronic Multispectral sensors was fully integrated in the embedded hardware FPGA technology and software based on virtual Instrumentation (NI LabView ®). The system was used as a colorimeter by using the chromogen reagent of 1-(2-pyridylazo)-2-naphthol (PAN) as an indicator and the results obtained together with the signal processing and pattern analysis using the method of the linear discriminant analysis, allowed to obtain excellent results in detection and classification of Pb(II), Cd(II), Zn(II), Cu(II), Fe(III) and Ni(II) ions, with almost the same level of performance in relation to those obtained from the UV-VIS spectrometers of high spectral resolution.

Despite ongoing efforts, the relationship between groin strength and injury remains unclear. The challenge of accurately predicting injuries presents an opportunity for researchers to develop pre-vention strategies to reduce the occurrence of such injuries. Consequently, this issue requires further investigation to obtain insights into effective mitigation strategies. In 120 male soccer players the maximum isometric strength of the hip muscle groups was measured, and the strength ratios were calculated. Previous injury and anthropometric data were registered. Injury data were collected following the FIFA/UEFA consensus. The K- Nearest Neighbour (k-NN), was used to predict the incidence of injury, while the significant predictive variables of the k-NN algorithm were fitted into a multivariate logistic regression model (LR) to analyze the likelihood of players sustaining a groin injury. The LR model determined two variables as significant predictors of groin injury. Players were less likely to sustain a groin injury by 76% for each decrease of the Adductors/Abductors isometric strength ratio in the non-dominant limb (OR = 0.238, CI 95%= [(0.098-0.572]). Players with a history of previous injury had a 67% greater risk of sustaining an injury (OR = 0.333, CI 95%= [(0.1068-1.038]). Isometric hip adductor and abductor strength im-balances of the non-dominant lower limb and a history of previous injury were risk factors for groin injury in soccer players.

Thermal fluctuations in two-dimensional (2D) isotropy systems at non zero finite temperatures can destroy the long-range (LR) magnetic order due to Mermin-Wanger theory. Interestingly, the magnetic anisotropy related to spin-orbit coupling (SOC) could stabilize magnetic order in 2D systems. Recently, 2D FexGeTe2 (3≤x≤7) with high curie temperature (TC), as a typical 2D van der Waals metallic ferromagnet, has not only made significant progress in synthetic methods and controlling ferromagnetism (FM), but also actively explored many device applications. In this Review, we introduce six experimental methods, ten ferromagnetic modulation strategies, and three spintronic devices of 2D FexGeTe2 materials. Overall, we have outlined the challenges and potential research directions in this field.

LASER cladding is a technique which has as main purpose to improve mechanical properties of materials surface with the addition of thin layers of other materials. Cladding/coating/addition material can be transferred to the substrate by powder injection, wire feeding or paste feeding and by the method of pre-placing the powders on the substrate. LASER cladding as a technique has only about 40 years. Is not yet a current technology and more work is needed, namely in the characterization of mechanical properties of new alloys used as base or cladding materials in this process. In this paper will be done initially an historical approach, followed by a description of the principles of the LASER cladding, a description of the applicability of the process and its advantages and limitations and the paper will end with a state of the art about the advances in new metallic alloys. So, this paper presents a review and the state of the art of the technological process and will be a contribution for the divulgation of this recent technique.

Background: In recent years, whole blood parameters and derivatives have been used as prognostic criteria in the course of the disease in various diseases. The prognostic nutritional index (PNI), the systemic immune-inflammation index (SII), the neutrophil-lymphocyte ratio (NLR) have been adapted as an indicator of inflammation and have been widely studied to define the severity of inflammation in some diseases. The aim of this study was to evaluate the relationship between parameters such as NLR, SII, PNI, controlling nutritional status (CONUT) score, nutritional risk index (NRI) and with immunonutrition status and disease activity in patients with ischemic stroke of small vessel, large vessel and other etiologies. Methods: We retrospectively evaluated the records of 1454 consecutive ischemic stroke patients hospitalized in the emergency department of Gaziosmanpasa Education and Research Hospital from 2019 to 2023. Results: Of the 1350 SVO patients included in the study, 58.8% had small vessel, 29.3% had large vessel and 11.9% had other etiologies. There was a significant difference between the 3 etiology groups for PNI and CONUT. The median PNI was 47.03 (41.33-52.85) in the other etiology group, 35.29 (33.69-37.25) in the small vessel group, and 34.11 (30.23-36.87) in the large vessel group. The CONUT median was 5(5-6) in the small vessel group, 5(4-6) in the large vessel group and 4(4-4) in the other etiology group. In addition, CONUT and PNI were also found to be independent risk factors for death. A negative significant correlation was observed between PNI and NLR (r:-0.692), SII (r:-0.591), CONUT (r:-0.685). Significant correlations were observed between CONUT and NLR (r:0.402), SII (r:0.312). Conclusion: PNI and SII were significantly associated with disease activity. PNI, CONUT and NRI as a more accurate prognostic indicator of nutritional status in patients with ischemic stroke of small vessel, large vessel and other etiologies. NLR and SII may be important predictive markers in the course and prognosis of stroke.

The experimental data in the literature concerning the Paramagnetic Meissner Effect (PME) or also called Wohlleben effect are reviewed with the emphasis on the PME exhibited by metallic, s-wave superconductors. The PME was observed in field-cool cooling (FC-C) and field-cool warming (FC-W) m(T)-measurements on Al, Nb, Pb, Ta, in compounds like e.g., NbSe2, In-Sn, ZrB12 and others and also in MgB2, the metallic superconductor with the highest transition temperature. Furthermore, samples with different shapes like crystals, polycrystals, thin films, bi- and multilayers, nanocomposites, nanowires, mesoscopic objects and porous materials exhibited the PME. The characteristic features of the PME, found mainly in Nb disks, like the characteristic temperatures T1 and Tp and the apparative details of the various magnetic measurement techniques applied to obbserve the PME are discussed. We also show that PME can be observed with the magnetic field applied parallel and perpendicular to the sample surface, that PME can be removed by abrading the sample surface and that PME can be introduced or enhanced by irradiation processes. The PME can be observed as well in magnetization loops (MHLs, m(H)) in a narrow temperature window Tp<Tc, which enables the construction of a phase diagram for a superconducting sample exhibiting the PME. We found that the Nb disks still exhibit the PME after more than 20 years, and we present the efforts of magnetic imaging techniques (scanning SQUID microscopy, magneto-optics, diamond nitrogen-vacancy (NV)-center magnetometry, and low-energy muon spin spectroscopy, (LE-μSR)). Various attempts to explain PME behavior are discussed in detail. Especially, magnetic measurements of mesoscopic Al disks brought out important details employing the models of a giant vortex state and flux compression. Thus, we consider these approaches and demagnetization effects as the base to understand the formation of the paramagnetic signals. New directions for further experimental and theoretical analysis are also outlined.

Introduction: The purposes of this study were to seek for overall ratio (OR) and anterior ratio (AR) patients data in normal occlusion and Angle’s malocclusion studies, and to assess if such results support Bolton’s standards as general references. Methods: Pubmed, Medline, CENTRAL and Scholar databases were searched up to February 2018 (CRD42018088438). Gray literature was explored through OpenGray. Non-randomized clinical studies, published in English and assessing Bolton’s OR and AR in normal occlusion and Angle’s malocclusion groups (Class I, Class II, Class II division 1, Class 2 division 2, Class III) patients were included. OR and AR means and standard deviations (SD) were collected. Potential covariates (study design, publication year, country where the study was conducted, number of cases, gender, mesiodistal measurement method, and calibration method) were also extracted. The National Health Heart Lung, and Blood Institute’s Quality Assessment Tool for Observational Cohort and Cross-Sectional Studies was used to assess each included studies quality. Pairwise Random-Effects and Multilevel Bayesian Network Meta-Analyses were used to synthesize available data. Results: Fifty-two observational studies were included (8872 participants; male/females 2674/3272; 16 studies lacked gender information). For normal occlusion, global pooled estimates for OR and AR means were 91.74% (95% CI: 91.37-92.10) and 78.24% (95% CI: 77.85-78.63), respectively. We could identify on Angle’s Class III patients meaningful OR and AR mean deviations from normal occlusion (0.89, 95% credible interval [CrI], 0.66-1.12, and 0.66, 95% CrI, 0.38-0.94, respectively), while on Class I patients we found a meaningful mean deviation from normal occlusion only for OR (0.25, 95% CrI, 0.03-0.47). Concerning gender impact, male patients presented higher OR (0.30, 95% CI 0.00-0.59) and AR (0.41, 95% CI 0.00-0.83) mean values than females in Class I. Conclusions: The results show that global pooled OR and AR mean values for normal occlusion patients are slightly above Bolton’s original values. Class I, for OR mean values, and Class III, for both OR and AR, are proportionally larger than normal occlusion patients. Gender had almost no impact on teeth mesiodistal proportion.

Metallic masters can be used as a metallic mold to replicate polymeric pieces with high resolution. Metallic masters with high resolution were created by photolithography technique and nickel electrodeposition technique. AZ 9260 photoresists and SPR 220-7.0 photoresists were used to coat metallic substrates and to compare results. Steel substrate and nickel substrate were used as the metallic substrate to compare results. Two different nickel electrodeposition protocols were used to compare results. In the conclusion section, was determined the best photoresist, metallic substrate, and nickel electrodeposition protocol to fabricate metallic masters.

Understanding of the correlation between the magnetomechancial coupling factors (k) and damping factors (Q^-1) is a key pathway to enhance the magnetomechanical power conversion ef-ficiency in laminated magnetoelectric (ME) composites by engineeringly manipulating the magnetic and mechanical properties of Fe-based amorphous metals. The k and Q^-1 factors of FeSiB amorphous ribbons annealed in air at different temperatures are investigated. It is found that k and Q^-1 factors are affected by both magnetic and elastic properties. The magnetic and elastic properties are equalized in terms of the magnetomechanical power efficiency for the low temperature annealing. The k and Q^-1 of FeSiB-based epoxied laminates with different stacking numbers show that the -3 dB bandwidth and Young’s modulus are equalized in terms of the magnetomechanical power efficiency for the high lamination stacking.

Among the thermophysical properties, the surface / interfacial tension, viscosity and density / molar volume of liquid alloys are the key properties for the modelling of microstructural evolution during solidification. Therefore, only reliable input data can yield accurate predictions preventing the error propagation in numerical simulations of solidification related processes. Due to experimental difficulties related to reactivity of metallic melts at high temperatures, the measured data are often unreliable or even lacking. The application of containerless processing techniques either leads to a significant improvement of the accuracy or makes the measurement possible at all. On the other side, accurate model predicted property values could be used to compensate the missing data; otherwise, the experimental data are useful for the validation of theoretical models. The choice of models is particularly important for the surface, transport and structural properties of liquid alloys representing the two limiting cases of mixing, i.e. ordered and phase separating alloy systems. To this aim, the thermophysical properties of the Fe-Si and Cu-Pb systems were analysed and the connections with the peculiarities of their mixing behaviours are highlighted.

In this paper, we investigate the accuracy and robustness of three classes of methods for solving two-phase incompressible flows on a staggered grid. Here, the unsteady two-phase flow equations are simulated by finite volumes and penalty methods using implicit and monolithic approaches (such as the augmented Lagrangian and the fully coupled methods), where all velocity components and pressure variables are solved simultaneously (as opposed to segregated methods). The interface tracking is performed with a Volume-of-Fluid (VOF) method, using the Piecewise Linear Interface Construction (PLIC) technique. The home code Fugu is used for implementing the various methods. Our target application is the simulation of two-phase flows at high density and viscosity ratios, which are known to be challenging to simulate. The resulting strategies of monolithic approaches will be proven to be considerably better suited for these two-phase cases, they also allow to use larger time step than segregated methods.

The goal of this paper is to explore the relationship between the specific non-performing loan ratio (NPL ratio) and the corresponding impact on the bank’s profitability and lending behavior. It also seeks to investigate the macroeconomic impacts of economies with excessively high NPL ratios as well as the efficacy and impact of alleviation measures used by banks and governments around the world to help facilitate a decrease in high NPL ratios. The possible implications and effects of the COVID-19 pandemic on NPL ratios is also addressed in this paper. It is found that when excessively high NPL ratios go unaddressed, the economy tends to suffer. On the other hand, this study shows that when measures are taken to reduce or eliminate the high NPL ratios, economic performance improves, and the reduction has a clear positive impact on the economy.

Extrusion-based additive manufacturing (AM) technologies (i.e., fused filament fabrication, FFF) mostly produce thermoplastic parts. However, producing metallic or ceramic parts by FFF is also a sintered-based AM process. FFF for metallic parts can be divided into five steps: (1) raw materials selection and feedstock mixture (including palletization), (2) filament production (extrusion), (3) production of AM components using the filament extrusion process, (4) debinding, and (5) sintering. These steps are interrelated, where the parameters interact with the other ones and have a key role in the integrity and quality of the final metallic parts. FFF can produce high-accuracy and complex metallic parts, potentially revolutionizing the manufacturing industry and taking AM components to a new level. In the FFF technology for metallic materials, material compatibility, production quality, and cost-effectiveness are the challenges to overcome to make it more competitive compared to other AM technologies, like the laser processes. This review provides a comprehensive overview of the recent developments in FFF for metallic materials, including the metals and binders used, the challenges faced, potential applications, and the impact of FFF on the manufacturing (prototyping and end parts), design freedom, customization, sustainability, supply chain, among others.

Plasmonic gold nanorods play important roles in nowadays state-of-the-art plasmonic sensing techniques. Most of the previous studies and applications focused on gold nanorods with relatively small aspect ratios, where the plasmon wavelengths are smaller than 900 nm. Gold nanorods with large aspect ratios are predicted to exhibit high refractive-index sensitivity (Langmir 2008, 24, 5233–5237.), which therefore should be promising for developing of high-performance plasmonic chemical- and bio-sensors. In this study, we developed gold nanorods with aspect ratios over 7.9, which exhibit plasmon resonances around 1064 nm. The refractive index (RI) sensitivity of these nanorods have been evaluated by varying their dielectric environment, whereby a sensitivity as high as 473 nm/RIU can be obtained. Furthermore, we have demonstrated the large-aspect-ratio nanorods as efficient substrate for surface enhanced Raman spectroscopy (SERS), where an enhancement factor (EF) as high as 9.47×10⁸ was measured using 4-methylbenzenethiol (4-MBT) as probe molecule. Finally, a type of flexible SERS substrate is developed by conjugating the gold nanorods with the polystyrene (PS) polymer. The results obtained in our study can benefit the development of plasmonic sensing techniques utilized in the near-infrared spectral region.

Food processing and consumption involves multiple contacts between biological fluids and solid materials of processing devices of which steel is one of the most common. Due to complexity of these interactions, it is difficult to identify the main control factors in the formation of undesirable deposits on the device surfaces that may affect safety and efficiency of the processes. Mechanistic understanding of biomolecule-metal interactions involving food proteins could improve management of these pertinent industrial processes and consumer safety in food industry and beyond. In this work, we perform a multiscale study of formation of protein corona on iron surfaces and nanoparticles in contact with cow milk proteins. By calculating the binding energies of proteins with the substrate we quantify the adsorption strength and rank proteins by the adsorption affinity. We use a multiscale method involving all-atom and coarse-grained simulations as well as generation of 3D structures of the proteins for this purpose. Finally, using the adsorption energy results, we predict the composition of protein corona on iron nanoparticles and flat surfaces via a competitive adsorption model.

The magnetic polarization tensor has a promising capability of determining the geometry and material properties of metallic samples. In this paper, a novel computation method is proposed to estimate the magnetic polarization tensors for the metallic samples using the boundary element method. In this method, the metallic sample is placed in a uniformly distributed magnetic field. Based on assumptions that the excitation frequency and/or the conductivity of the sample is very high, the metallic sample is regarded as a perfect electrical conductor (PEC). Therefore, the scattered field at a certain distance can be simulated. By utilising the boundary element method, the magnetic polarization tensor can be derived from the simulated scattered field. The theoretical calculation is presented and simulations and experiments have been carried out to validate the proposed method. The results from the simulation are matched with the analytical solution for the case of sphere samples. Moreover, there is a good agreement between the simulation results and the experimental results for the copper cylindrical samples.

The potential of the Additive Manufacturing technologies is impeded by the surface finish obtained on the as-manufactured material. Therefore, the influence of various surface treatments, commonly applied to space hardware, on the mechanical properties of three selected metallic alloys (SS316L, AlSi10Mg, Ti6Al4V) prepared by using Selective Laser Melting (SLM) and Electron Beam Melting (EBM) additive manufacturing processes have been investigated. Within this study, SLM using EOS M400 and EOS M280 equipment and in addition EBM using an ARCAM Q20 machine have been applied for sample manufacturing. A half-automated shot-peening process followed by a chemical and/or electrochemical polishing or Hirtisation® process has been applied in order to obtain lower surface roughness compared to their as-received states. Special emphasize has been taken on their tensile, fatigue, and fracture toughness properties. In addition, their stress corrosion cracking (SCC) behaviour including microstructural analysis using HR-SEM have been investigated.

In this paper, we establish some inequalities bounding the ratio Г_p,k(x)/Г_p,k(y), where Г_p,k(.) is the (p,k)-analogue of the Gamma function. Consequently, some previous results are recovered from the obtained results.

Background: Despite the tremendous effort in hamstring injury prevention, injury rates in soccer remain elevated. Hypothesis: Hamstring and hip/pelvic isometric strength imbalances may increase the likelihood of hamstring strain injury (HSI) occurrence amongst soccer players.Study design: Case-control study.Methods: In 120 male soccer players (mean age: 20.0 +/- 6.96 years) pre-season maximum isometric strength of the hip adductors, abductors, flexors, and knee flexors were measured, and strength ratios were calculated. Previous injury and anthropometric data were registered. Injury data were collected following the FIFA/UEFA consensus. A multivariate and Machine learning-based Logistic Regression model was employed to estimate the likelihood of players sustaining a hamstring injury.Results: 21 players sustained 32 hamstring injuries. Players with higher abduction strength in the dominant leg had an 18.5% lower risk of sustaining a hamstring injury (OR = 0.818, CI 95% = [(0.695-0.964]). No other significant contributor variables were found to be significant predictors of hamstring injury in the player group (p> 0.05).Conclusion: Isometric strength of the abductor muscles in the dominant limb had a significant association with hamstring injury.Clinical relevance: Our findings indicate the utilization of hip strength measurements as an integral component of the pre-season screening assessment, thereby affirming prior research on the correlation between lumbo-pelvic stability and incidence of hamstring injuries. Consequently, clinicians should contemplate incorporating hip strengthening exercises into regular training sessions, rehabilitation programs, and injury prevention protocols especially indicated when lower hip strength levels are observed.

For thermoelectric materials study and development, it is very important to measure the electrical power and efficiency of a thermoelectric generator (TEG). In this study, thermoelectric properties such as electrical conductivity, Seebeck coefficient, and thermal conductivity of cement composites with graphene nanoplatelets and metallic oxides (Fe2O3, ZnO, MnO2) are measured and subsequently used to figure out the output electrical power and efficiency. A maximum of 1.5 W power per square meter for a temperature difference of about 50 °C can be estimated using GnP-ZnO added cement composites. This paper also talks about how to make a cement composite-based structural TEG module to enhance the total output voltage, power, and efficiency of the system.

As a 21st century trend, sustainability has encompassed the entire world economy, including industry. Today the concept of "Industry 4.0" is known, resulting from advances in ICT (information and communication technologies). In recent years, companies in the metal materials industry have also implemented strategies and technologies belonging to the Industry 4.0 concept. The main purpose of the manuscript is to identify the key issues in the evolution of the development of the metal materials industry. The transition to a higher level of its evolution is based on two vectors, namely: the ecological paradigm, as a vector of in-depth knowledge, and sustainable material, as a vector that ensures sustainability in the areas of convergence of systems in the spheres of life and social consciousness. The systems that have an impact on the sustainable development of the metallic materials industry, through the interactions between them, are: the technological system, the social system and the natural-ecological system. Global knowledge re-quires the use of all inter and multidisciplinary knowledge, which ultimately contributes to the definition and characterization of new intersystem scientific branches: Ecometallurgy, Metallurgical Economics, Metallurgical Ecosociology and Sustainable Materials Engineering. The paper is considered a research study based on elements such as: literary foundations, using databases such as Web of Science (WoS), Scopus, Google Scholar, sustainable universal principles and legislative parameters.

The Mediterranean Sea is one of the most impacted basin in terms of microplastics pollution. Land-based activities are the major sources of plastic litter to the ocean, with harbors probably representing significant hotspots. In the framework of the SPlasH! project (Stop alle Plastiche in H2O, Interreg Marittimo project), microplastics were sampled in three north-western Mediterranean harbors during summer and winter. In this study, the areal concentrations of microplastics ranged from 5,576 to 379,965 items.km-2. A decreasing gradient was observed from the inner to the outer zones of the studied harbors, pointing out these enclosed systems as hotspots regarding microplastic pollution. During the summer, because of an enhancement of port activities, the areal concentrations of microplastics were higher than in winter. The investigation microplastics size classes distribution in the surface waters revealed that microplastic within a size range between 300 µm and 500 µm were depleted. During this study, we assessed trace metal partitioning (Pb, Fe, Cu, V, Cd and As) between the dissolved phase and biofilm, thus highlighting concentrations within the biofilm two and six orders higher than those in the dissolved phase. This result strongly suggest trace metal bioaccumulation within the biofilm. When trace metal concentrations are normalized over the corresponding surface of microplastics and microplastics, higher values were obtained for microplastics evidencing their enhanced capacities to bioaccumulate contaminants with respect to macroplastics.

In exploring the intricacies of financial analysis, this study delves into the efficacy of traditional financial ratios versus cash flow ratios in foreseeing a company's fiscal well-being. By harnessing the PRISMA 2020 framework, an exhaustive and systematic dissection of diverse scholarly articles was embarked upon. The quest was to unearth the more reliable predictor of financial stability among these two sets of ratios. With a methodical examination of academic writings, this inquiry juxtaposed various models, scrutinizing their foresight capabilities. The revelations were telling; cash flow ratios emerged as more potent forecasters compared to their traditional counterparts. Intriguingly, models that blend both ratio types showed a marked improvement in predictive accuracy, hinting at a synergistic effect. This underscores the insight that while traditional ratios are informative, their amalgamation with cash flow ratios yields a richer, more rounded grasp of a company’s fiscal state. Conclusively, for stakeholders, especially investors, adopting this dual-ratio approach is pivotal for enlightened decision-making. This research enriches the financial analysis domain by spotlighting the salience of cash flow ratios, advocating for their integration with conventional methods for a sharper financial health appraisal.

A robust bank industry is a major player in the stability of an economy. The operational efficiency and stability of banks are therefore paramount. By way of financial ratios and Z-score, this study analysed UT Bank’s financial performance prior to the 2017 bank sector reforms in Ghana. Annual financials over a ten year period (2007-2016) were used. Debt management practices of UT Bank per the results obtained were quite on the hind side and unimpressive. This was reflected in the poor leverage and risk management variables. UT Bank would have been unable to meet creditors’ claims considering the mean average values of debt-to-assets and debt-to equity ratios of 0.76 and 0.90 respectively. The entire bank sector will benefit if credit management practices of individual banks are refreshed and worked on. The bank industry regulator should tighten its supervisory and monitoring role over banks to help detect early signs of non-performing banks. The study further recommends that statutory lending limits of banks be re-enforced to uphold the threshold of 10 percent for unsecured loans and 25 percentage for secured loans of net owned funds of the bank.

The Casimir–Lifshitz friction force and the heating rates of two metal plates with a narrow vacuum gap between them during nonrelativistic motion of one of them are calculated analytically and numerically within the framework of fluctuation electrodynamics. Changes in material properties are taken into account using the Bloch-Grüneisen and modified Bloch-Grüneisen (with finite residual resistance) resistivity models within the Drude approximation. It is shown that identical plates with the same initial temperature have the same heating rate, determined by the power of the friction force, and the possibility of measuring the friction force from the heating kinetics of nonmagnetic metal plates with temperatures of 1–10 K is substantiated.

The review starts by highlighting the significance of nuclear power plants in contemporary world, especially its indispensable role in the global efforts to reduce CO2 emissions. Then, it describes the impact of irradiation on microstructure and mechanical properties of reactor structural materials. The main part provides the reader with a thorough overview of crystal plasticity models developed to address the irradiation effects so far. All three groups of most important materials are included. Namely, the Zr alloys used for fuel cladding, austenitic stainless steels used for reactor internals and ferritic steels used for reactor pressure vessel. Other materials, especially those considered for construction of future fission and fusion nuclear power plants, are also mentioned. The review pays also special attention to ion implantation and instrumented nanoindentation which are a common way to substitute costly and time-consuming neutron irradiation campaigns.

Molecular dynamics simulations were carried out to investigate the atomic structure of a model Cu64Zr36 bulk metallic glass (BMG). It is found that the amount of icosahedral content of the system is significantly increased in a well relaxed structure. While we considered four connection types of vertex-, edge-, face-, and volume-sharing, the huge cluster in the relaxed samples mainly involve volume-type connection and exhibits a remarkable athermal plasticity that great stiffness and great yield strength compared to the as-quenched samples. In addition, the bond-angle distribution of annealed sample shows sharp peaks at specific bond angles which is an evidence of crystallized Laves-phase formed by icosahedral atoms, however the peaks are to be broaden after loading, which indicates decreasing amount of icosahedral content and their shape distortion. These results suggest that icosahedral content in a bulk metallic glasses plays a key role to determine the mechanical properties such as rigidity and maximum stress carrying capacity.

This article presents an experimental study focused on the impact of supplementing pure gasoline (E0) with bioethanol, gradually increasing the biofuel concentration up to 70% (E10, E50, and E70). The research was conducted in two phases: In the first phase (Part I), the engine's operation involved varying engine speeds (n = 2000 rpm, n = 2500 rpm) and adjusting throttle openings (15%, 20%, 25%) to analyze changes in brake torque, thermal efficiency, and ecological indicators. The second phase (Part II) aimed to complement and clarify the study data. Here, the engine was maintained at a constant speed (n = 2000 rpm) and brake torque (MB = 80 Nm) while altering ignition timing. The findings revealed that increasing the bioethanol concentration up to 70% led to modest enhancements in engine brake torque and thermal efficiency. However, the most significant impact was observed in the reduction of greenhouse gas emissions and incomplete combustion byproducts. The study also established that achieving higher thermal efficiency requires compensating for the extended ignition delay phase resulting from bioethanol addition by advancing ignition timing. Nevertheless, this approach is constrained by the escalating emissions of carbon dioxide and hydrocarbons. These findings provide valuable insights into optimizing the balance between bioethanol supplementation, engine performance, and environmental sustainability in spark ignition engines.

Autism spectrum disorder (ASD) is a neurodevelopmental condition characterized by impaired social communication and repetitive or stereotypic behaviours. In utero exposure to environmental chemicals, such as polychlorinated biphenyls (PCBs), may play a role in the etiology of ASD. We examined the relation between plasma PCB concentrations measured during pregnancy and autistic behaviours in a subset of children aged 3–4 years old in the Maternal-Infant Research on Environmental Chemicals (MIREC) Study, a pregnancy and birth cohort of 546 mother-infant pairs from Canada (enrolled: 2008-2011). We quantified the concentrations of 6 PCB congeners that were detected in >40% of plasma samples collected during the 1st trimester. At age 3–4 years, caregivers completed the Social Responsiveness Scale-2 (SRS), a valid and reliable measure of children’s reciprocal social and repetitive behaviors and restricted interests. We examined SRS scores as both a continuous and binary outcome, and we calculated Bayesian predictive odds ratios for more autistic behaviours based on a latent variable model for SRS scores >60. We found no association between plasma PCB concentrations and autistic behavior, However, we found small and imprecise increases in the mean SRS score and odds of more autistic behaviour for the highest quartile of plasma PCB concentrations compared with the lowest quartile; for instance, an average increase of 1.1 [95%PCI: −0.5, 2.6] in the mean SRS (exposure contrast 4^th versus 1^st quartile) for PCB138 translated to an odds ratio of 1.6 [95%PCI: 1.0, 2.5]. Our findings illustrate the importance of measuring associations between PCBs and autistic behaviour on both continuous and binary scales.

Entangled metallic wire material (EMWM) can be utilized as a novel elastic element in vibration isolation devices for mechanical actuators. This paper presents a vibration experiment aimed at investigating the degradation behavior of mechanical performance in EMWM under cyclic compressive environment. An electric vibration testing system, coupled with an isolation structure, is employed to apply compressive loads to the EMWM specimens. Through visual observations and quasi-static compression tests, the variations in geometric morphology and mechanical properties are studied, considering different relative densities and stress amplitudes. The results incidate a significant reduction in the compressed dimension of the specimens as the number of cycles increases, without any wire fractures or wear. Moreover, the mechanical properties exhibit an increasing secant modulus and a decreasing loss factor. These variations ultimately lead to a gradual deviation of the vibration characteristics of the isolation structure from its design state. To predict the mechanical property degradation of EMWM, prediction models are proposed, incorporating dimension, modulus and damping by fitting the obtained results. This research provides valuable experimental data and presents an effective method to determine the operational lifetime of vibration isolators utilizing EMWM.

We consider a specific holographic model in the limit where the gauge field does not couple to the rest of of the holographic fields (gravity and scalar sector) and investigate a phase of matter at zero charge density, a realistic feature that may have implications for disordered strange metals. We then pick a specific form of the gauge coupling $Z(\alpha)$ with a certain disorder realization and argue that this provides a hard-gapped insulator with exponentially-suppressed conductivity by holographic methods. The limit is non-trivial: as there is backreaction at zero density amount, surviving in the coupled case.

Luminescent properties of epitaxial Cu2O thin films were studied in 10-300 K temperature range and compared with luminescent properties of Cu2O single crystals. Cu2O thin films were deposited epitaxially by the electrodeposition method on either Cu or Ag substrates at different processing parameters, which determined the epitaxial orientation relationships and encapsulated surface. Cu2O (100) and (111) single crystal samples were cut from a crystal rod grown by the floating zone method. Luminescence spectra of thin films contain the same emission bands as single crystals around 720, 810 and 910 nm, characterizing VO2+, VO+ and VCu defects, correspondingly. Additional emission bands, whose origin is under discussion, are observed around 650-680 nm, while the exciton features are negligibly small. The relative mutual contribution of the emission bands varies depending on the particular thin film sample. Existence of the domains of crystallites with different orientation determines the polarization of luminescence. PL of both Cu2O thin films and single crystals is characterized with negative thermal quenching in the low temperature region, the reason of this phenomenon is discussed.

The strong coupling between individual quantum emitters and resonant optical micro/nanocavities is beneficial to understand light and matter interactions. Here we propose a plasmonic nanoantenna placed on a metal film to achieve an ultra-high electric field enhancement in the nanogap and ultra-small optical mode volume. The strong coupling between a single quantum dot and the designed structure is investigated in detail by both numerical simulations and theoretical calculations. When a single QD is inserted into the nanogap of the silver nanoantenna, scattering spectra show remarkably large spectral splitting and typical anti-crossing behavior of the vacuum Rabi splitting, which can be realized in the scattering spectra by varying the nanoantenna thickness. Our work shows a possible way to enhance light-matter interaction at a single quantum emitter limit, which can be useful for future quantum and nanophotonic applications.

The flowability of a powder is a characteristic dependent on both the particle ensemble's physical properties as well as the testing equipment and conditions. In powder bed additive manufacturing processes (SLM, EBM), flowability can be used to predict the quality of the deposited powder layer. However, how representative flowability is for the powder bed layer quality is not always clear.In this work, we compared several steel powders, as well as different testing methods. Each powder had an individual combination of composition or particle size distribution. Furthermore, the flowability testing equipment and methods were selected according to standards (Tap density, Hall flow) or referring to the published literature (angle of repose, FT4 Powder Rheometer). After measuring the flowability of different samples for each testing method, we created a database to evaluate a first correlation between the different testing methods. Finally, with a Powder Rheometer, we investigated for one sample some flow properties as function of different particle size distributions.

An increasing use of non-metallic reinforcement is problematic as it has to be detected at the stage of accepting construction works, or later when expert opinions are prepared for the building. In contrast to metallic reinforcement, location of this type of reinforcement is difficult using non-destructive techniques. Small diameters of rebars and their location in a tested element were troublesome. This article describes an attempt to locate non-metallic reinforcement in a concrete element and the masonry. Tests were performed using an ultrasonic tomograph and GPR with a broad range of frequencies.

This study presents a new form of velocity distribution in laminar liquid flow in rectangular microchannels using the eigenfunction expansion technique. Darcy friction factor and Poiseuille number are also obtained analytically. Due to the symmetry of the solutions, the effects of changing the aspect ratio from 0 to ∞ are also discussed. Using finite element method (FEM), the obtained analytical results are further compared with the 3D numerical simulations for the rectangular microchannels with different range of aspect ratio and pressure gradient, and excellent agreements were found. These findings provide additional insights in interpreting the results of the pressure-driven flows in finite aspect ratio microchannels, in which very precise comparison with the macroscale theory is crucial.

This document presents the design and manufacture of a reflectarray (RA) antenna for the Ku-band, based on a fully-metallic 3D architecture. The reflectarray unit cell is formed by a square-shaped waveguide section ended in a short circuit, that is the reflectarray back ground plane. Each cell has the ability of configuring the phase of its own reflected field by means of resonators perforated on the walls of the cell waveguide section. The resonator-based waveguide cell introduces the 3D character to the design. The geometry of the resonators and its size variation introduces the phase behaviour of each cell, conforming the radiation pattern of the reflectarray. This design explores the potential of phase value truncation (6 states and 2 states), and demonstrates that proper pattern results can be obtained with this phase truncation.

In many advanced industrial applications, the thickness is a critical index, especially for metallic coatings. However, the variance of lift-off spacing between sensors and test pieces affects the measured voltage or impedance, which leads to unreliable results from the sensor. Massive research works have been proposed to address the lift-off issue, but few of them applies to the thickness measurement of planar metallic films with finite-size circular (disk) geometry. Previously, a peak-frequency feature from the swept-frequency inductance was used to compensate the measurement error caused by lift-offs, which was based on the slow-changing rate of impedance phase term in the Dodd-Deeds formulas. However, the phase of measured impedance is nearly invariant merely on a limited range of sample thicknesses and working frequencies. Besides, the frequency sweeping is time-consuming, where a recalibration is needed for different sensor setups applied to the online real-time measurement. In this paper, a single-frequency algorithm has been proposed, which is embedded in the measurement instrument for the online real-time retrieval of thickness. Owing to the single-frequency measurement strategy, the proposed method does not need to recalibrate for different sensor setups. The thickness retrieval is based on a triple-coil sensor (with one transmitter and two receivers). The thickness of metallic disk foils is retrieved from the measured electrical resistance of two transmitter-receiver sensing pairs. Experiments on materials of different electrical conductivities (from direct current), thicknesses and planar sizes (radii) have been carried out to verify the proposed method. The error for the thickness retrieval of conductive disk foils is controlled within 5 % for lift-offs up to 5 mm.

The issues of metallic scrap management and its utilization in manufacturing plants are nowadays intensely considered to address essential sustainability guidelines. Efficient recycling procedure for shop floor metallic scrap is not yet available because of abundance and contamination of nonmetallic constituents. Other ferrous metallic scrap are melted and purified during secondary steelmaking to get products in the form of blooms and billets are obtained. This study illustrates the potential of powder technology (powder metallurgy (PM) and metal injection molding (MIM)) based process for solid-state recycling and attainment of usable products. Industrially downgraded grinding sludge is pulverized and used as a raw material. Results showed properties of sintered parts are significantly improved due to in-situ reduction and densification during sintering. Recyclability Index (RI) was created to compare the effect of process variables on obtained products. Based on RI, recycled ferrous parts have about 70% comparable properties with equivalent pure iron parts. Complex reduction and sintering behavior in MIM, particularly, diffusion and pore volume kinetics limits applicability of MIM with this recycling approach. However, few industrial parts were developed and manufactured by PM based approach to validate the applicability of this novel recycling-cum-manufacturing process for the production of porous parts.

Biomineralization has become a research hotspot and attracted widespread attention in the field of carbonate sedimentology. In this study, Bacillus licheniformis DB1-9 was used to induce the calcium carbonate precipitation at different magnesium calcium molar ratios in the laboratory to further explore the biomineralization mechanism. Phylogenetic tree shows that the bacteria belongs to Bacillus licheniformis species. The ammonia and carbonic anhydrase can be released by this bacteria, resulting in the pH increase, and the carbonic anhydrase can also promote the hydration reaction of carbon dioxide and subsequently produce the bicarbonate and carbonate ions to elevate the supersaturation of calcium carbonate in the liquid culture medium to facilitate the precipitation of carbonate minerals. The calcites have a shape of rhombohedron, dumbell, and elongation, and aragonite often appears in the form of mineral aggregates, besides that there are also the spherical and the fusiform minerals. FTIR result shows there are some organic functional groups, such as C-O-C and C=O, beside of the characteristic peaks of the calcite and the aragonite, indicating that microbial metabolism is closely related to the mineral formation. The superthin slices of the bacteria analyzed by HRTEM, SAED, EDS and STEM show that the surface and EPS can adsorb a large number of calcium ions and magnesium ions and EPS may act as the nucleation sites, what’s more, the intracellular nanometer-scale sphere areas show the amorphous structures, and the intracellular calcium ions and magnesium ions suggeste that they can be transported from the outside to inside the cell by diffusion along the concentration grade from high to low. This study may provide some references to further understand the biomineralization mechanism induced by microorganisms in the laboratory and the field, and also helps to explore the reason of the transition of calcite sea to aragonite sea in the geological history.

The strength of laser joined metal and plastic hybrids is based purely on adhesion. Unpolar plastics like polypropylene depend solely on the mechanical adhesion while polar plastics like polyamide 6.6 develop covalent bonds with the metal. In this research the influence of different surface metallizations on the lap shear strength of laser joined hybrids was investigated. Sandblasted AISI 304 was used as base metal and reference. Aluminum and titanium coatings were deposited by the means of Arc-PVD. Polypropylene and polyamide 6.6 were utilized as polar und unpolar plastics. The lap shear strength of all hybrids with polyamide 6.6 was higher than the polypropylene samples. For all investigated variations of the laser power, scanning speed and the cohesive and adhesive failure modes, the samples joined with the sandblasted AISI 304 showed the highest lap shear strength. The reduction in lap shear strength for the coated samples was due to the increased difference in thermal conductivity between the plastics and the coating materials. This lead to increased warping and residual stresses. It can be concluded that the thermal properties of the metallization in laser joined metal and plastic hybrids has a high impact on the lap shear strength.

The first objective of this paper is to investigate the scaling behavior of liquid-vapor phase transition in FCC and BCC metals starting from the zero-temperature four-parameter formula for cohesive energy. The effective potentials between the atoms in the solid are determined using lattice inversion techniques as a function of scaling variables in the above formula. These potentials are split into repulsive and attractive parts as per the Weeks-Chandler-Anderson prescription, and used in the coupling-parameter expansion for solving the Ornstein-Zernike equation supplemented with an accurate closure. Thermodynamic quantities obtained via the correlation functions are used to obtain critical point parameters and liquid-vapor phase diagrams. Their dependence on the scaling variables in the cohesive energy formula are also determined. Equally important second objective of the paper is to revisit coupling parameter expansion for solving the Ornstein-Zernike equation. The Newton-Armijo non-linear solver and Krylov-space based linear solvers are employed in this regard. These methods generate a robust algorithm that can be used to span the entire fluid region, except very low temperatures. Accuracy of the method is established by comparing the phase diagrams with those obtained via computer simulation. Avoidance of the 'no-solution-region' of Ornstein-Zernike equation in coupling-parameter expansion is also discussed. Details of the method and the complete algorithm provided here would make this technique more accessible to researchers investigating thermodynamic properties of one component fluids.

Abstract: The baculovirus expression vector (BEV) system is an efficient, cost effective and scalable method to produce recombinant adeno-associated virus (rAAV) gene therapy vectors. Most BEV designs emulate the wild type AAV transcriptome and translate the AAV capsid proteins, VP1, VP2 and VP3 from a single mRNA transcript with three overlapping open reading frames (ORFs). Non-canonical translation initiation codons for VP1 and VP2 reduce their abundances relative to VP3. Changing capsid ratios to improve rAAV vector efficacy requires theoretical modification of translational context. We have made a Lac repressor inducible system to empirically regulate expression of VP1 and VP2 proteins relative to VP3 in the context of the BEV. We demonstrate the use of this system to tune the abundance, titer and potency of a neurospecific rAAV9 serotype derivative. VP1:VP2:VP3 ratios of 1:1:8 gave optimal potency for this rAAV. It was discovered that ratios of capsid proteins expressed were different than ratios that ultimately were in purified capsids. Over expressed VP1 did not become incorporated into capsids while over expressed VP2 did. Overabundance of VP2 correlated with reduced rAAV titers. This work demonstrates a novel technology for controlling production of rAAV in the BEV system and shows a new perspective on the biology of rAAV capsid assembly.

The scale and accessibility of passive global surveillance have rapidly increased over time. This provides an opportunity to calibrate the performance of models, algorithms, and reflectance ratios between remote sensing devices. Here we test the sensitivity and specificity of Eucalypt chlorophyll-a reflectance ratio (ECARR) and Eucalypt chlorophyll-b reflectance ratio (ECBRR) to remotely identify eucalypt vegetation in Queensland, Australia. We compare reflectance ratio values from Sentinel-2 and Planet imagery across four sites of known vegetation composition. All imagery was transformed to reflectance values and Planet imagery was additionally scaled to harmonize across Planet Scenes. ECARR can identify eucalypt vegetation remotely with high sensitivity, but shows low specificity and is impacted by the density of the vegetation. ECBRR reflectance ratios show similar sensitivity and specificity when identifying eucalypt vegetation but with values an order of magnitude smaller than ECARR. We find that ECARR was better at identifying eucalypt vegetation in the Sentinel-2 imagery than Planet imagery. ECARR can serve as a general chlorophyll indicator but is not a specific index to identify Eucalyptus vegetation with certainty.

In vitro testing is the first important step in the development of new biomaterials. The human fetal osteoblast cell line hFOB 1.19 is a very promising cell model; however, there are vast discrepancies in cultivation protocols, especially in the cultivation temperature and the presence of selection reagent, geneticin (G418). We intended to use hFOB 1.19 for the testing of Zn-based degradable metallic materials. However, the sensitivity of hFOB 1.19 to zinc ions has not yet been studied. Therefore, we compared the toxicity of zinc towards hFOB 1.19 under different conditions and compared it with that of the L929 mouse fibroblast cell line. We also tested the cytotoxicity of three types of Zn-based biomaterials in two types of media. The presence of G418 used as a selection reagent decreased the sensitivity of hFOB 1.19 to Zn2+. hFOB 1.19 were more sensitive to Zn2+ at elevated (restrictive) temperatures. hFOB 1.19 were less sensitive to Zn2+ than L929 (both as ZnCl2 and extracts of alloys). Therefore, the appropriate cultivation conditions of hFOB 1.19 during biomaterial testing should be chosen with caution.

Defensive structure is important in transportation field for kinds of intentional or unintentional explosion. Structures subjected to unconfined and confined explosion will bear different blast loads and their dynamic responses are different. The present work focus on the dynamic response mechanism of steel plate under unconfined and confined blast loads through both numerical and experimental studies. In the experiment, Digital Image Correlation (DIC) technique was applied to record and analyze the dynamic response process of large-scale field blast test. The DIC measured curve and the numerical calculated curves agrees well in both the trends and the peak values. Then, the dynamic response mechanism of steel plate under unconfined blast (UB) load and confined blast (CB) load were compared and discussed. Results show that the dynamic response of plate can be divided into three phases under both UB and CB loads, while with different mechanism. In phase I, plastic hinge starts from the center and moves to the boundary in UB condition, while in case of CB, plastic hinge occurs close to the boundary and moves in the opposite direction. In phase II, two plastic hinge lines propagates towards each other, and a platform exists between the boundary and the central area remains undeformed in UB condition, while in CB condition, larger deformation in peripheral region rather than central area produces.

This research aims to deepen the understanding of the relationship between conductivity and morphology in polypyrrole (PPy) via a comparison of the bipolaron to polaron ratios with a focus on the C-H deformation area. PPy samples were synthesized with different surfactants: sodium dodecyl sulfate (SDS), cetyltrimethylammonium bromide (CTAB), and tween 80 (TW). The study revealed that SDS significantly altered the bipolaron and polaron in C-H deformation region and showed higher conductivity than other surfactants. Notably, the morphological shifts to a sheet-like structure when using ammonium sulfate (APS) contrasted with the particle-like form observed with ferric chloride (FeCl3). These results showed that if the oxidant changed, the bi-polaron and polaron ratios in C-H deformation were unrelated to PPy morphology. However, this work showed a consistent relationship between SDS use, the bipolaron and polaron ratios in the C-H deformation, and the conductivity properties. Moreover, the natural positive charge of PPy and negatively charged SDS molecules may lead to an electrostatic interaction between PPy and SDS. This work assumes that this interaction might cause the transformation of polaron to bipolaron in the C-H deformation region, resulting in improved conductivity of PPy. This work offers more support for the future investigation of PPy characteristics.

In this paper we will provide a new equation that explains why there are three generations or families of leptons and quarks, respectively. We will also explain why all those particles have the known mass ratios amongst their three respective generations and flavors. We will also tackle the problem of Yukawa couplings being arbitrary parameters in the Standard Model Higgs mechanism, which is a long standing problem do to their formulaic dependence on the Higgs Vacuum Expectation Value (VEV). We will attempt to solve this problem and provide a strong argument through an equation for Yukawa couplings of all leptons and quarks via a new methodology that depends on the running of the fine-structure constant on the Q scale, quantum numbers and the Weinberg angle (also on the Q scale). We will also make predictions for all three left-chiral neutrino mass eigenstates and we will provide upper limits for the three right-chiral neutrino mass eigenstates

Wound healing is rarely seen as a problem in healthy individuals; however, under certain pathophysiological conditions, this process can be impaired, leading to the emergence of chronic wounds, which are themselves a serious public health problem. This work aimed to review the most important and recent literature on the use of metallic nanoparticles, in this case those produced from plant extracts, and their application as healing agents. For this, we firstly provided an insight into the pathophysiology of the wound healing process and then the main routes for obtaining metallic nanoparticles. The methodology of synthesis, which is part of the so-called green synthesis, has been the subject of several studies reporting the use of medicinal plants as subtracts for the production of different nanoparticles (of silver, gold, and zinc). Additionally, their use as wound healing agents is close related with biological properties such as antimicrobial, anti-inflammatory, and healing. Finally, we addressed in vitro and in vivo studies reporting the efficiency of metallic nanoparticles synthesized with plant extracts and applied in different pharmaceutical forms on the wound healing process. Based on these satisfactory results, we verified that metallic nanoparticles are potential therapeutic alternatives when compared to the traditional synthetic healing agents, thus foreseeing the production of new drugs in the pharmaceutical market.

In this study, additive manufacturing of reinforced parts using metallic wire as both a reinforcement component and a shape memory stimulus through Fused Deposition Modeling (FDM) was investigated. A Shape Memory Polymer (SMP) restores its original shape and recovers it upon specific stimuli. This research employed chromium-nickel metal wire as a reinforcing component to enhance mechanical properties and introduce the capability for thermal stimulation of polylactic acid (PLA) via electrical current using the "in-situ impregnation" method within FDM process. Reinforced specimens were fabricated with wire with two diameters of 0.1 and 0.15 mm, along with two volume percentages of 5 and 10. Comprehensive evaluations encompassing mechanical (tensile and flexural) and thermal properties of the printed specimens were conducted. The outcomes revealed a significant enhancement in both tensile and flexural properties of the polymer matrix due to the embedding metallic wire, even under elevated temperatures during bending test. Furthermore, the thermal properties of the reinforced specimens were examined by subjecting them to various voltages, resulting in temperature ranging from 36.4 to 150.1°C. These findings highlight the ability to tailor a wide range of mechanical properties and shape recovery in the reinforced specimens by carefully selecting the wire volume fraction, voltage, and wire diameter, thus regulating the materials properties with specific application requirements.

Binder jet printed components typically have low overall density in the green state and high shrinkage and deformation after heat treatment. It has previously been demonstrated that, by including nanoparticles of the same material in the binder, these properties can be improved as the nanoparticles can fill the interstices and pore throats between the bed particles. The beneficial effects from using these additive binder particles can be improved by maximising the binder particle size, enabling the space within the powder bed to be filled with a higher packing efficiency. The selection of maximum particle size for a binder requires detailed knowledge of the pores and pore throats between the powder bed particles. In this paper, a raindrop model is developed to determine the critical radius at which binder particles can pass between pores and penetrate the bed. The model is validated against helium pycnometry measurements and binder particle drop tests. It is found that the critical radius can be predicted, with acceptable accuracy, using a linear function of the mean and standard deviation of the particle radii. Percolation theory concepts have been employed in order to generalise the results for powder beds that have different mean particle sizes and size distributions. The results of this work can be employed to inform the selection of particle sizes required for binder formulations, to optimise density and reduce shrinkage in printed binder jet components.

AbstractLarge numbers of urban lakes are facing issues related to cyanobacteria, commonly known as blue-green algae, resulting in significant threats to humans and animal health due to their production of microtoxins and Anatoxin-A. These toxins induce acute effects including gastrointestinal distress, and respiratory problems, underscoring the need to protect urban lakes to safeguard community health and ecosystem well-being. A comprehensive monitoring program is a critical step to address cyanobacteria-related issues. Monitoring results of dissolved phosphorous, nitrates(N), Total Kjeldahl Nitrogen (TKN), total phosphorous (TP), TSS, and Escherichia coli (E. coli) concentrations, are used to understand the importance of different pathways events during dry conditions (no prior rainfall) and wet events (rainfall during or proceeding monitoring events) plus a microbial source tracking procedure, to understand impacts on growth characteristics of cyanobacteria and microtoxins. The Mann-Kendall Trend Test is used to characterize trends of various parameters (using transitions of ‘wet’ and ‘dry’ to the Lake and within the Lake), to identify the impact of various management strategies and/or the impact of various sources from overland land uses for a) wet events to the Lake, b) dry events to the Lake, c) wet events in the Lake, and d) dry events within the Lake. Microbial source tracking methods are used along the shoreline of Fairy Lake to interpret elevated levels of fecal pollution and E. coli bacteria in water samples, aiding in the identification of pollution sources. Blue-green algae have been observed at least once each year from 2018 to 2023. Microtoxins and Anatoxin-A were present in nine samples with a maximum of 1.72 mg/L and 0.02 mg/L, respectively. Frequent beach closures have occurred every year, raising public concerns regarding both ecological and recreational aspects for Fairy Lake.

Hydrodechlorination reaction of 3-(benzo-1,3-dioxol-5-yl)-3-chloro-2-methylacrylaldehyde in the presence of different low metal content heterogeneous mono- or bi-metallic catalysts was tested for the synthesis of the fragrance Helional® (3-[3,4-methylendioxyphenyl]-2-methyl-propionaldehyde). In particular, mono Pd/Al2O3, Rh/Al2O3 or bi-metallic Pd-Cu/Al2O3, Rh-Cu/Al2O3 catalysts were tested in different reaction conditions from which it emerged that mono-Rh/Al2O3 was the best performing catalyst allowing to achieve 100% substrate conversion and 99% selectivity towards Helional® in 24h at 80°C, p(H2) 1.0 MPa in the presence of a base. To establish correlations between atomic structure and catalytic activity, catalysts were characterized by Cu, Rh and Pd K-edge XANES, EXAFS analysis. These characterizations allowed to verify that the formation of Pd-Cu alloys and the presence of Cu oxide/hydroxide species on the surface of the Al2O3 support, are responsible for the very low catalytic efficiency of bimetallic species tested.

The dynamic and surface manipulation of the M13 bacteriophage meeting application demands enable a pathway to design efficient applications with high selectivity and responsivity rate. Herein, we report the role of the M13 bacteriophage thin film layer deposited on an optical nanostructure involving gold nanoparticles/SiO2/Si and its influence on optical and geometrical properties. The thickness of the M13 phage layer was either controlled by varying the concentration or humidity exposure levels, and optical studies were conducted. We designed a standard and dynamic model based upon three-dimensional finite-difference time-domain (3D FDTD) simulations distinguishing the necessity of each model under variable conditions. As seen from the experiments, the origin of respective peak wavelength positions is addressed in detail with the help of simulations. The importance of the dynamic model was noted when humidity-based experiments were conducted. Inexpensive, multi-wavelength optical characteristics from a single structure, reproducibility, and reversible properties are significant advantages of involving M13 bacteriophage. We believe this work will provide fundamental insight into understanding and interpreting the geometrical and optical properties of the nanostructures involving M13 bacteriophage.

Open-cell metallic foams used as catalyst supports exhibit excellent transport properties. In this work, a unique application of metallic foam, as pelletized catalyst in a packed bed reactor, is examined. By using a wall-segment Computational Fluid Dynamics (CFD) setup, parametric analyses are carried out to investigate the influence of foam morphologies (cell size ϕ=0.45-3 mm and porosity ε=0.55-0.95) and intrinsic conductivity on flow and heat transport characteristics in a slender packed bed (N=Ddp=6.78) made of cylindrical metallic foam pellets. The transport processes have been modeled using an extended version of conventional particle-resolved CFD, i.e., flow and energy in inter-particle spaces are fully resolved, whereas porous-media model is used for the effective transport processes inside highly-porous foam pellets. Simulation inputs include the processing parameters relevant to Steam Methane Reforming (SMR), analyzed for low (Rep~100) and high (Rep~5000) flow regimes. The effect of foam morphologies on packed beds has shown that the desired requirements contradict each other, i.e., increase in cell size and porosity favor the reduction in pressure drop, however lowering the heat transfer efficiency. A design study is also conducted to find the optimum foam morphology of a cylindrical foam pellet at higher Rep~5000, which yields ϕ = 0.45, ε = 0.8. Suitable correlations to predict the friction factor and the overall heat transfer coefficient in a foam packed bed have been presented, which considers the effect of different foam morphologies over a range of particle Reynolds number, 100≤Rep≤5000.

We have recently proposed a pre-quantum, pre-space-time theory as a matrix-valued Lagrangian dynamics on an octonionic space-time. This pre-theory offers the prospect of unifying the internal symmetries of the standard model with gravity. It can also predict the values of free parameters of the standard model, because these parameters arising in the Lagrangian are related to the algebra of the octonions which define the underlying non-commutative space-time on which the dynamical degrees of freedom evolve. These free parameters are related to the algebra $J_3(\mathbb O)$ [exceptional Jordan algebra] which in turn is related to the three fermion generations. The exceptional Jordan algebra [also known as the Albert algebra] is the finite dimensional algebra of 3x3 Hermitean matrices with octonionic entries. Its automorphism group is the exceptional Lie group $F_4$. These matrices admit a cubic characteristic equation whose eigenvalues are real and depend on the invariant trace, determinant, and an inner product made from the Jordan matrix. Also, there is some evidence in the literature that the groups $F_4$ and $E_6$ could play a role in the unification of the standard model symmetries, including the Lorentz symmetry. The octonion algebra is known to correctly yield the electric charge values (0, 1/3, 2/3, 1) for standard model fermions, via the eigenvalues of a $U(1)$ number operator, identified with $U(1)_{em}$. In the present article, we use the same octonionic representation of the fermions to compute the eigenvalues of the characteristic equation of the Albert algebra, and compare the resulting eigenvalues with the known mass ratios for quarks and leptons. We find that the ratios of the eigenvalues correctly reproduce the [square root of the] known mass ratios for quarks and charged leptons. We also propose a diagrammatic representation of the standard model bosons, Higgs and three fermion generations, in terms of the octonions, exhibiting an $F_4$ and $E_6$ symmetry. In conjunction with the trace dynamics Lagrangian, the Jordan eigenvalues also provide a first principles theoretical derivation of the low energy value of the fine structure constant, yielding the value $1/137.04006$. The Karolyhazy correction to this value gives an exact match with the measured value of the constant, after assuming a specific value for the electro-weak symmetry breaking energy scale.

This study explores the evolution of price-to-book (P/B) ratios among European banks from 2005 to 2020, period where the majority of banks in different countries had a P/B ratio below 1. By dissecting banks' accounting equity into investor contributions and earnings-derived components, the research aims to evaluate how each component of equity affects these ratios and investigates whether their dynamics shifted during the period. We address a gap in prior research that has not extensively examined how individual equity components affect the overall P/B ratio. This aspect is crucial, especially in scenarios where the increase of specific components compensates for declines in others, thereby stabilizing total equity values. Our methodology involves regression analyses using a panel data model with random effects. The findings reveal that earnings-related equity components significantly influence P/B ratios. In contrast, investor contributions; which strengthen the solvency of the entity, appear to have a minimal impact. Additionally, our analysis highlights a significant quadratic relationship between the P/B ratios and both the profit or loss reported on Income Statements and distributed dividends.

High intrinsic water use efficiency (WUEi), the ratio of leaf photosynthesis to stomatal conductance, may be a useful trait in adapting crops to water-limited environments. Carbon isotope ratios can be a useful indicator of WUEi, but might not be well correlated with it if the plants compared differ substantially in mesophyll conductance. In this study, six cultivars of soybeans previously shown to differ in WUEi in indoor experiments were grown in the field in Beltsville, Maryland, and mid-day WUEi was measured on nine clear days during mid-seasons of two years. Measurement dates were chosen for diverse temperatures, and air temperatures ranged from 21 to 34 oC on the different dates. Corrected carbon isotope delta values for 13C (CID) were determined on mature, upper canopy leaves harvested during early pod filling each year. WUEi differed among cultivars both years and the differences were consistent across measurement dates. Correlations between mean WUEi and CID were not significant in either year. It is concluded that consistent cultivar differences in WUEi exist in these soybean cultivars under field conditions, but that carbon isotope ratios may not be useful in identifying them.

The growth of solid particles during liquid phase sintering was modeled by the Cellular Automata method. The binary phase diagram and Fickian approach for the diffusion process were applied to simulate the chemical composition variation in liquid and solid phases during sintering. The Oswald-Ripening effect was considered during the dissolution of the solid phase in the liquid phase. It is used to define the probability of solid-phase dissolution by the liquid phase and develop the model to simulate the alloy with solid solubility. So, the microstructure could be modeled in the liquid phase sintering process.

As 180-degree meanders are observed in abundance in nature, a meandering channel with two consecutive 180-degree bends was designed and constructed to investigate bed topography variations. These two 180-degree mild bends are located between two upstream and downstream straight paths. In this study, different mean velocity to critical velocity ratios have been tested at the upstream straight path to determine the meander's incipient motion. To this end, bed topography variations along the meander and the downstream straight path were addressed for different mean velocity to critical velocity ratios. In addition, the upstream bend's effect on the downstream bend has been investigated. Results indicated that the maximum scour depth at the downstream bend has increased as a result of changing the mean velocity to critical velocity ratio from 0.8 to 0.84, 0.86, 0.89, 0.92, 0.95, and 0.98 by respectively 1.5, 2.5, 5, 10, 12, and 26 times. Moreover, increasing the ratio increased the maximum sedimentary height by 3, 10, 23, 48, 49, and 56 times. The upstream bend's incipient motion was observed for the mean velocity to critical velocity ratio of 0.89, while the downstream bend was equal to 0.78.

The present study investigation, our results on characterization of commercially pure-Ti alloy brazed with metallic glass ribbons of Ti20Zr20Cu60-xNix (x = 30, 40, and 50) metallic glass ribbons were produced using a vacuum melt spinner. These ribbons were then used as filler materials for vacuum brazing of two Ti alloy plates at 1268, 1277 and 1279 K for a period of 10 min. Field-Emission Scanning Electron Microscopy (FESEM), Transmission Electron Microscopy (TEM) and the energy dispersive X-ray spectroscopy (EDX). The as-spun ribbons showed fully amorphous structure when examined on both surfaces by XRD and also verified by TEM investigation. The brazing joint of two Ti-plates using the metallic glass ribbon when brazed with Ni50 was found to be of very high strength. FESEM characterization of the cross-section of the brazed joints shows sub-micron size grains uniformly distributed in the matrix with brighter appearance. FESEM and EDX analysis revealed that the sub-micron grains are rich in Ti & Ni while the matrix phase mainly consisted of Ti. BSE image along with EDS Analysis indicated that the brazed joint has a presence of NiTi2 and Cu2 (Ni Zr) phases which could be responsible for increase in the strength of the brazed joint.

In estimating the maximum and minimum index void ratios for mixtures of sand and silt, the values of several empirical constants must be determined based on the type of sand and silt involved. These empirical constants are the filling coefficient, a, and embedment coefficient, b, both of which can be determined either through lab testing or correlations. These constants are then used in equations to predict the maximum and minimum index void ratios of the sand-silt mixtures. The study reported here developed simple correlations for estimating the filling and embedment coefficients using readily obtained laboratory data. These models were found to be excellent in developing filling and embedment coefficients that accurately (R2 values typically of 0.94 or greater.) predicted values of the index void ratios for sand and silt mixtures.

Objectives: Few studies in literature evaluate the "mean measure" of root divergence. Most of them are linear measurements, they hardly describe the dental furcation conformation. It is left to the subjectivity of the operator deciding whether a furcation is convergent or divergent. The goal of this study is to create a visual evaluation method to overcome these problems giving a conformation of the entire interradicular space. Material and methods: A user-friendly software (Paint®, Windows10®) was used to measure endo-oral radiographs of upper and lower molars. Three kinds of measurements were taken. Three operators used the software to measure 20 radiographs, then the technique was repeated on 250 radiographic images to identify an average measurement. The ratio of these three measurements allowed to develop a new visual evaluation method of the interradicular space. Results: Intra and inter-operator reproducibility was statistically assessed on a sample of 20 anonymous endo-oral radiographs measured by 3 blind operators. Then, a sample of 250 anonymous endo-oral radiographs were measured by a blind operator and were statistically evaluated to identify an average value to define a main conformation of the interradicular space. Measurements made by the 3 operators on the 20 radiographic images showed that the technique is reproducible, and a mean value of the interradicular space was obtained. Conclusions: A new anatomical evaluation of the interradicular space in its entirety, which could help the clinicians in the therapy of furcated molars, can be obtained.

When gravity is quantum, the point structure of space-time should be replaced by a non-commutative geometry. This is true even for quantum gravity in the infra-red. Using the octonions as space-time coordinates, we construct a pre-spacetime, pre-quantum Lagrangian dynamics. We show that the symmetries of this non-commutative space unify the standard model of particle physics with $SU(2)_R$ chiral gravity. The algebra of the octonionic space yields spinor states which can be identified with three generations of quarks and leptons. The geometry of the space implies quantisation of electric charge, and leads to a theoretical derivation of the mysterious mass ratios of quarks and the charged leptons. Quantum gravity is quantisation not only of the gravitational field, but also of the point structure of space-time.

This review focuses on the therapeutic effects of metallic ions when released in physiological environments. Recent studies have shown that metallic ions like Ag+, Sr2+, Mg2+, Mn2+, Cu2+, Ca2+, P+5, etc., have shown promising results in drug delivery systems and regenerative medicine. These metallic ions can be loaded in nanoparticles, mesoporous bioactive glass nanoparticles (MBGNs), hydroxyapatite (HA), calcium phosphates, polymeric coatings, and salt solutions. The metallic ions can exhibit different functions in the physiological environment such as antibacterial, antiviral, anti-cancer, bioactive, biocompatible, and angiogenic effect. Furthermore, the metallic ions can be loaded in scaffolds to improve osteoblast proliferation, differentiation, bone development, fibroblast growth, and improved wound healing efficacy. Moreover, different metallic ions possess different therapeutic limits. Therefore, further mechanisms need to be developed for the highly controlled and sustained release of these ions. This review paper summarizes the recent progress in the use of metallic ions in regenerative medicine and encourages further study of metallic ions as a solution to cure diseases.

Resistive patch array incorporating with metallic backplane provided an effective way to the achievement of broadband metamaterial absorbers(MAs). When loading metallic metamaterial to resistive MA, the outstanding construction helps realize more flexible and diversified forms of broadband absorption. In this paper, we attempted to load metallic resonators(MRs) to resistive MA in the three-dimensional construction, which benefits further enhancement of lower-frequency absorption. Simulation showed that the partial absorption band was separated to lower frequency, while the rest of broadband absorption was unaffected. Meanwhile, after combining multi-unit of the proposed MAs, the stair-stepping broadband absorption was also achieved. At last, three samples were fabricated. The agreements between simulations and experimental results demonstrated that resistive MA loaded with MRs provided an effective way for further enhancement of lower-frequency absorption with almost no change of the absorbing structure and areal density. Thus, it is worthy to expect a wide range of applications to emerge inspired from the proposed attempt.

This study explores the effects of powder-to-liquid ratio on the performance characteristics of lost foam casting coatings. The investigation focuses on how variations in this ratio affect key properties including apparent viscosity, shear thinning behavior, coating weight, and surface morphology. Through a series of controlled experiments, coatings were prepared with different powder-to-liquid ratios and assessed for their physical and application properties. The results indicate that increasing the powder-to-liquid ratio raises the apparent viscosity and modifies shear thinning behavior. Notably, ratios exceeding 2.0 result in a sharp increase in viscosity that impedes coating application. The optimal powder-to-liquid ratio was determined to be between 2.0 and 2.2, where coatings demonstrated enhanced uniformity, improved particle distribution, and superior surface morphology. Coating weight increased up to a ratio of 2.2 but decreased beyond this threshold due to excessive viscosity. Both microscopic and macroscopic analyses confirmed that a ratio of 2.0 to 2.2 strikes the best balance for coating performance. These findings underscore the importance of precise powder-to-liquid ratio control to optimize the quality of lost foam casting coatings, offering valuable insights for refining coating formulations and application techniques in industrial contexts.

For each $t\in(-1,1)$, exact values of the least upper bounds $$ H(t)=\sup_{\E X=t,\,\E X^2=1} \frac{\E\abs{X}^3}{\E \abs{X-t}^3},\quad \sup_{\E X=t,\,\E X^2=1} \frac{L_1(X)}{L_1(X-t)} $$ are obtained, where $L_1(X)=\E|X|^3/(\E X^2)^{3/2}$ is the non-cental Lyapunov ratio. It is demonstrated that these values are attained only at two-point distributions. As a corollary, S.\,Shorgin's conjecture is proved that states that the exact value is $$ \sup\frac{L_1(X)}{L_1(X-\E X)}= \frac{\sqrt{17 + 7\sqrt7}}{4} = 1.4899\ldots, $$ where the supremum is taken over all non-degenerate distributions of the random variable $X$ with the finite third moment. Also, in terms of the central Lyapunov ratio $L_1(X-\E X)$, an analog of the Berry--Esseen inequality is proved for Poisson random sums of independent identically distributed random variables with the constant $$ 0.3031\cdot H\left(\frac{\E X}{\sqrt{\E X^2}}\right) \left(1-\frac{(\E X)^2}{\E X^2}\right)^{3/2} \le 0.3031\cdot \frac{\sqrt{17 + 7\sqrt7}}{4}<0.4517.$$ where $\Law(X)$ is the common distribution of the summands.

Deficiency, with its two constituents of protein-energy deficiency and micronutrient deficiencies, remains a substantial health burden in underdeveloped nations. It is the largest cause of sickness and death worldwide, particularly harming hundreds of millions of small children and pregnant women. In order to improve the protein-energy and micro- macro needs of developing countries, food products made from compositing flours are required. Ethiopian injera is a fermented, leavened flatbread produced primarily from teff flour. However, when compared to teff injera, injera made from sorghum flour and its blend has been found to have textural flaws. Uncontrolled staling of sorghum flour incorporated teff injera resulted in limited softness, freshness, rollability, brittleness anddryness which create big problems during storage. Due to its numerous health advantages and nutritional worth, fenugreek is regarded as a key functional food element. As a result, this study was conducted to identify the regression equation of injera formulations and optimise the teff, sorghum, and fenugreek flour blending ratios that result in injera with higher quality properties. Using mixture design methods and a D-optimal design, the effects of blending flour ratios on injera quality were examined. Teff flour alone injera was used as the control. Fourteen injera formulations were created using limited mixtures of teff (50-100%), sorghum (0-50%), and fenugreek (0-5%). Proximate, staling rate, mineral, antinutritional components, and sensory qualities were all taken into account as response variables in this study. The study's findings showed that increasing the proportion of fenugreek flours in injera made from teff-sorghum-fenugreek mixing ratios improved nutritive values, improved sensory appeal, textural characteristics and reduced staling rate. Generally speaking, the best injera blending ratio was found to be 64.1% teff, 32% sorghum, and 3.80% fenugreek in terms of overall qualitative qualities.

This paper proposes a linear eddy-current feature to determine the radius of a metallic ball in a non-contact manner. An electromagnetic eddy-current sensor with two coils is placed co-axially to the metal ball during measurement. It is well known that the distance between the sensor and test piece (i.e. lift-off) affects eddy-current signals. In this paper, it is found that the peak frequency feature of inductance spectrum is linear to the lift-off spacing between the centre of coil and ball. Besides, the slope of peak frequencies versus lift-offs is linked to the radius of ball. The radius of metallic balls is retrieved from the experimental and embedded analytical result of the slope. Measurements have been carried out on 6 metallic balls with different radii. The radius of the metallic ball can be retrieved with an error of less than 2 %.

Eddy current based approaches have been investigated for a wide range of inspection applications. Dodd-Deeds model and the truncated region eigenfunction expansion (TREE) method are widely applied in various occasions, mostly for the cases that the sample is relatively larger than the radius of the sensor coil. The TREE method converts the integral expressions to the summation of many terms in the truncated region. In a recent work, the impedance of the co-axial air-cored sensor due to a plate of finite radius was calculated by the modified Dodd-Deeds analytical approach proposed by authors. In this paper, combining the modified analytical solution and the TREE method, a new finite region eigenfunction expansion (FREE) method is proposed. This method involves modifying its initial summation point from the first zero of the Bessel function to a value related to the radius of the plate, therefore makes it suitable for plate with finite dimensions. Experiments and simulations have been carried out and compared for the verification of the proposed method. Further, the planar size measurements of the metallic circular plate can be achieved by utilising the measured peak frequency feature.

The paper introduces a valuable new description of fatigue strength in relation to material properties and thus a new perspective on the overall understanding of the fatigue process. Namely, a relation between the endurance limits and the accompanying values of the critical resolved shear stress (CRSS) for various metallic materials has been discovered by means of a multiscale approach for fatigue simulation. Based on the uniqueness of the relation, there is a strong indication that it is feasible to relate the endurance limit to the CRSS, and not to the ultimate strength as often done in the past.

This study was based on the corresponding elemental abundances of carbonaceous - chondrites and the Solar photospheric elemental abundances [1]. The comparative analysis between the average magnesium, silicon and iron abundances of the Solar System and the abundances of these elements in potential nearby planetary systems was based on the Mg, Si and Fe abundances of host stars, which are in the Galactic thin disk within 25 parsecs distance from the Sun. The stellar abundance data had been taken from the Hypatia Catalog, which contains high precision data of chemical elements. We show that in general there are no significant differences between the molar Mg/Si and Fe/Si ratios of the most examined stars and the corresponding elemental ratios of the Solar System. However, the comparative study also shows that a significant fraction of the nearby extrasolar terrestrial planets may have higher bulk Mg/Si ratio than Solar, but the Solar Fe/Si ratio can relatively be frequent. We conclude that the medium - sized metallic cores can relatively be common in the rocky planetary interiors, while the mantle mineralogy for most of the rocky exoplanets in the Solar neighborhood may differ from that of Earth.

Despite being well established phenomena, solidification principles are experiencing tough challenges in their application to explain microscale transport phenomena in additive manufacturing melt pool. The problem becomes even more complicated when applied to multicomponent bulk metallic glass matrix composites (BMGMC) whose behavior is dubious and still not fully understood. The aim of the present study is to highlight pathways to overcome these challenges. A comprehensive nucleation and growth model based on original KGT theory and Rappaz modification is proposed encompassing actual transient thermophysical BMGMC data to predict evolving microstructure during additive manufacturing. The model is aimed at pictorial representation of in-situ ductile phase dendrite evolution from melt pool during solidification using two-dimensional cellular automaton (CA) methods. It is proposed to be coded in MATLAB® using commercial simulation code ABAQUS® at back end for macroscopic heat transfer model. The results will be compared with experimental values for validation.

A novel process design for damage-free and highly accurate positional integration of an optical multi-axial force sensor into a hollow tube by means of rotary swaging is introduced. Numerical simulations reveal relevant process phenomena of thin disc joining inside a pre-toothed hollow tube and help to find an optimal process design. Experimental trials show a significant effect of axial material flow and the number of tools in a rotary swaging process. By taking these effects into account, a successful form- and force-fit joining of the sensor carrying discs into the tube can be achieved. A successful joining of an optical sensor for bending forces and torque measurement shows hysteresis-free sensory behavior and thus backlash-free joining of the sensor carrier discs. The paper finishes with presenting an approach for closed-loop position controlling during the joining process and numerically investigation of the process design.

Previously, various techniques have been proposed for reducing the lift-off effect on the thickness measurement of the non-magnetic films, including the peak-frequency feature and phase feature in the Dodd-Deed analytical formulation. To realise a real-time feedback response on the thickness monitoring, the phase term in the Dodd-Deeds formulation must be taken off the integration. Previous methods were based on the slow change rate of the phase term when compared to the rest of the term – the magnitude term. However, the change rate of the phase term is still considerable for a range of working frequencies. In this paper, a high-frequency feature has been found. That is, the ratio between the imaginary and real part of the phase term is proportional to the integral variable under high frequencies. Based on this proportion relationship, the phase term has been taken out; and a thickness algorithm has been proposed. By combing the measured impedance from the custom-built sensor (three coils), the thickness of the metallic film can be reconstructed. Experiments have been carried out for the verification of the proposed scenario. Results show that the thickness of the metal film can be reconstructed with a small error of less than 2 %, and immune to a reasonable range of lift-offs.

Physics theory has yet to settle on specific descriptions for new elementary particles, for dark matter, and for dark energy forces. Our work extrapolates from the known elementary particles. The work suggests well-specified candidate descriptions for new elementary particles, dark matter, and dark energy forces. This part of the work does not depend on theories of motion. This work embraces symmetries that correlate with motion-centric conservation laws. The candidate descriptions seem to explain data that prior physics theory seems not to explain. Some of that data pertains to elementary particles. Our theory suggests relationships between masses of elementary particles. Our theory suggests a relationship between the strengths of electromagnetism and gravity. Some of that data pertains to astrophysics. Our theory seems to explain ratios of dark matter effects to ordinary matter effects. Our theory seems to explain aspects of galaxy formation. Some of that data pertains to cosmology. Our theory suggests bases for inflation and for changes in the rate of expansion of the universe. Generally, our work proposes extensions to theory in three fields. The fields are elementary particles, astrophysics, and cosmology. Our work suggests new elementary particles and seems to explain otherwise unexplained data.

Background: Glioblastoma (GBM), a malignant grade IV tumor, is the most malignant brain tumor due to its hyper-proliferative and apoptosis-evading characteristics. The signal transducer and activators of transcription (STAT) family genes, including STAT3 and STAT5A, have been indicated to play important roles in GBM progression. Increasing number of reports suggest that Garcinol, a polyisoprenylated benzophenone and major bioactive component of Garcinia indica contains potent anti-cancer activities. Material & Methods: The present study investigated the anti-GBM effects of garcinol, focusing on the STAT3/STAT5A activation, using a combination of bioinformatics, in vitro, and ex vivo assays. Results: Our bioinformatics analysis of TCGA - GBM cohort (n=173) showed that STAT3 and STAT5A are preferentially elevated in primary and recurrent GBM, compared to non-tumor brain tissues, and is significantly correlated with reduced overall survival. In support, our immunohistochemical staining of a GBM cohort (n=30) showed an estimated 5.3-fold (p<0.001) elevation in STAT3 and STAT5A protein expression in primary and recurrent GBM versus the non-tumor group. In vitro, garcinol treatment significantly suppressed the proliferative, invasive, and migratory potential of U87MG or GBM8401 cells, dose-dependently. In addition, garcinol anticancer effect significantly attenuated the GBM stem cell-like phenotypes, as reflected by diminished ability of U87MG or GBM8401 to form colonies and tumorspheres and suppressed expression of OCT4 and SOX2. Furthermore, analysis on GBM transcriptome revealed an inverse correlation between the level of STAT3/5A and hsa-miR-181d. Garcinol-mediated anti-GBM effects were associated with an increased hsa-miR-181d/STAT3 and hsa-miR-181d/5A ratio. Conclusion: We present evidence of anti-GBM efficacy of garcinol mediated by enhancing the hsa-miR-181d/STAT3 and hsa-miR-181d/5A ratios in GBM cells. Our findings suggest a potential new therapeutic agent for combating aggressive GBM.

Metallic glass matrix composites are unique new materials which have superior mechanical properties as compared to existing conventional materials. Owing to this, they are potential candidates for various future structural applications. However, they suffer from disadvantages of brittleness, poor ductility and little or no toughness and they manifest catastrophic failure on application of force. Their behavior is dubious and require extensive experimentation to draw conclusive results. In present study, which is continuation of previous study by author, an effort has been made to overcome this pitfall by simulation. A quantitative mathematical model based on KGT theory has been developed to describe nucleation and growth of crystalline phase dendrites in glassy matrix during solidification. It yields information about numerical parameters to understand the behavior of each individual element in a phase in multicomponent sluggish slurry and their effect on final microstructural evolution. Model is programmed and simulated in MATLAB®. Its validation is done by comparison with identical curves reported in literature previously for similar alloys. Results indicate that effect of incorporating all heat transfer coefficients at macroscopic level and diffusion coefficients at microscopic level play a vital role in refining the model and bringing it closer to actual experimental observations. Two types of hypoeutectic and eutectic systems namely Zr₆₅Cu₁₅Al₁₀Ni₁₀ and Zr_47.5Cu_45.5Al₅Co₂ respectively were studied. Simulation results were found to be in good agreement with prior simulated and experimental values

Ultrasonic-guided lamb wave approach is an effective non-destructive testing (NDT) method used for detecting localized mechanical damage, corrosion, and welding defects experienced in metallic pipelines. Signal processing of the guided waves is often challenged due to the complexity of operational conditions and environments in the pipelines. Machine learning approaches in recent years, including convolutional neural networks (CNN) and long short-term memory (LSTM), have exhibited their advantages to overcome these challenges for signal process and data classification of complex systems, thus great potential for damage detection of critical oil/gas pipeline structures. In this study, a CNN-LSTM hybrid model is utilized for decoding ultrasonic guided waves for damage detection of metallic pipelines, and twenty-nine features are extracted as input to classify different types of defects from metallic pipes. The prediction capacity of the CNN-LSTM model is assessed by comparing it to the CNN and LSTM. The results demonstrate that the CNN-LSTM hybrid model exhibits much higher accuracy, with 94.8%, as compared to those of CNN and LSTM. Interestingly, the results also reveal that predetermined features, including time-, frequency-, and time-frequency domains, could significantly improve the robustness of the deep learning approaches, even though the deep learning approaches are often believed they include automated feature extraction, without the hand-crafted steps as the shallow learning do. Furthermore, the CNN-LSTM model displays higher performance when the noise level is relatively low (e.g., SNR=9 or higher), as compared to the other two models, but its prediction drops gradually with the increase of the noise.

Bulk metallic glass matrix composites have emerged as competent structural material of future bearing potential structural applications. However, the optimum percentage of crystallinity required to produce enough toughness that it can serve as structural component is still a matter of debate. In this study, an effort is made to address this problem by inoculation. A controlled amount of carefully selected inoculant is introduced in Zr_47.5Cu_45.5Al₅Co₂ bulk metallic glass matrix composite during melting and solidification. Its effect in promoting crystallinity is checked by detailed electron back scatter diffraction (EBSD) mapping. Proper pattern capture, background correction, binning, Hough space transformation, step size selection, indexing and matching with well-defined crystal structure files have shown to reflect upon map quality. This shows and bears direct relation with effect of inoculation. Results from two independent laboratories are reported. Inoculation treatment is shown to be advantageous.

This research aims to delve into the intricacies of combustion processes, specifically focusing on heating oil and a blend of heating oil with TPO (Tire Pirolysis Oil) in a self-developed evaporative combustion chamber featuring steam injection. The primary objective is to scrutinize the impact of steam injection on the combustion dynamics. Conducting a series of tests, the investigation involved the meticulous manipulation of stoichiometric ratios while introducing ambient air through gravity fuel flow. Subsequent iterations of these tests incorporated the introduction of steam into the ambient air stream. The examination encompassed the combustion of both heating oil and the TPO blend within the combustion chamber. The evaluation criteria comprised an in-depth analysis of flame characteristics, temperature distribution within the combustion chamber, and the quantification of emissions such as particulate matter (PM), nitrogen oxides (NOx), carbon dioxide (CO2), carbon monoxide (CO), and water vapor (H2O). Throughout the experimentation phase, commercially available diesel fuel served as the primary fuel source. To facilitate the tests, the combustion chamber under scrutiny was seamlessly integrated into an AVL engine test bench system. Essential parameters, including fuel consumption, were meticulously gauged using an AVL 735 fuel flow meter, while fuel temperature was monitored using the AVL 745 fuel temperature conditioning system. The intake air, a crucial element in the combustion process, was quantified with precision using an AVL Flowsonix sensor. Emission measurements were conducted meticulously using state-of-the-art equipment, with gaseous emissions analyzed using an AVL FTIR AMA i60 exhaust gas analyzer. Simultaneously, soot emissions were quantified through employment of an AVL Micro Soot sensor. This comprehensive approach not only delves into the fundamental aspects of combustion but also extends its reach to the exploration of innovative techniques, such as steam injection, to enhance combustion efficiency and reduce emissions. The integration of advanced measurement tools ensures a robust and thorough analysis of the combustion process and its environmental implications.

Traditional methods of non-metallic materials joining for industrial uses are limited to lasers, or induction or conduction heating. The precision and efficiency for large-scale applications are difficult to be achieved at the same time. Here in this paper, we report a precise microwave welding method induced by localized surface plasmon of metallic macro-gaps under microwave excitation. The proposed method utilizes energy from well-developed commercial microwaver, and benefits from the precision of localized surface plasmon, an oscillating electron cloud excited by electromagnetic waves, which is currently under hot investigation only at micro- or nano-scales. The method is applied to the welding of polymers to solve the problems of complex processing equipment and high processing energy consumption in the traditional welding process, so as to cope with the growing energy and environmental crisis. Finite element numerical simulations are used to study the distribution characteristics of electric fields and temperature fields. The results show that the process is a high quality, efficient, low consumption and environmentally friendly green process compared to traditional polymer welding methods.

Surface processes such as coatings, corrosion, photocatalysis, and tribology are greatly diversified by acid-base interaction at the surface overlayer. This study focuses on the action of metallic copper surface as an electron donor/acceptor related to inactivation of viruses; it was found that regarding Cu2O or Cu materials electrostatic interaction plays a major role in virus inactivation. We applied TPPE method to clarify the mechanism of electron transfer (ET) occurring at light irradiated copper surfaces. The TPPE characteristics was strongly influenced by the environments, which correspond to the temperature and environment dependence of the total count of emitted electrons in the incident light wavelength scan (PE total count, NT), the photothreshold, and further the activation energy (E) analyzed from Arrhenius plot of NT values obtained in the temperature-increase and subsequent temperature-decrease processes. In this study we reexamined the dependence of the TPPE data from two types of Cu metal surfaces: Sample A, which was mechanically abraded in alcohols, water, and air, and Sample C, which was only ultrasonically cleaned in these liquids. The NT for both Samples slowly increased with increasing temperature, reached a maximum (NTmax) at 250C (maximum temperature, Tmax), and after that decreased. For Sample A the NTmax value decreased in the order H2O > CH3OH > C2H5OH > (CH3)2CHOH > C3H7OH, although the last alcohol gave Tmax = 100C, while with Sample C the NTmax value decreased in the order: C3H7OH > (CH3)2CHOH > C2H5OH > CH3OH > H2O. Interestingly, both orders of the liquids were completely opposite: this means that Cu surface can possess two-way character. The NT intensity was found to be strongly associated with the change of the hydroxyl group (Cu-OH) to the oxide oxygen (O2) in the O1s spectra in the XPS measurement. The difference between the above orders was explained by the acid-base interaction mode of the Cu-OH group with the adsorbed molecule on the surfaces. The H2O adsorbed on Sample A produces the electric dipole Cu-OH+---:OH2 (--- hydrogen bond), while the C3H7OH and (CH3)2CHOH adsorbed on Sample C produce ROH+---:O(H)-Cu (R = alkyl groups). Gutmann’s acceptor number (AN) representing the basicity of the liquid molecules was found to be related to the TPPE characteristics: (CH3)2CHOH (33.5), C2H5OH (37.1), CH3OH (41.3), H2O (54.8) (the AN of C3H7OH could not be confirmed). With Sample A the values of NTmaxa and EaUp1 both increased with increasing AN (Up1 means the 1st temperature-increase process). On the other hand, with Sample C the values of NTmaxc and EcUp1 both decreased with increasing AN. These findings suggest that Sample A acts as an acid, while Sample C functions as a base. However, in the case of both types of Samples A and C the NTmax values were found to increase with increasing EUp1. It was explained that the EUp1 values depending on the liquids originate from the difference in the energy level of the hydroxyl group radical at the surface denoted. This is able to attract electrons in the neighborhood of the Fermi level of the base metal by tunnelling. After that due to Auger emission electrons are released, leading to the ET in the overlayer. These electrons are considered to have a strong ability of reducibility.

The existence of the hole on a plate affects the calculation of eddy current problems. Consequently, the accuracy for the prediction of the material properties decreases if the effect of the hole is not taken into account. In this paper, a novel analytical method based on the modified integration range is proposed which can address the presence of the hole. Due to the presence of the hole, the conventional Dodd-Deeds analytical solution cannot be used to calculate the inductance change. Therefore, a revised upper integration limit is introduced to replace the original limit -- ∞ when using the co-axially air-core electromagnetic sensor. With the presence of the hole, the magnitude of the received signal reduces, and the peak frequency feature changes. The analytical method is validated by measured and numerical simulation results. It is found that the upper limit is related to the radius of the open hole. With the new technique, the thickness of sample plates with holes can be estimated based on the peak frequency feature.

Zirconium based bulk metallic glasses are industrially valuable materials which commercial market grows rapidly. Surface modification of these metallic glasses by high-intensity lasers is relatively new and costly treatment promising great advantages over classical surface processing methods. In this work we perform the case study of surface modification of Zr$_{46}$Cu$_{36.8}$Ag$_{9.2}$Al$_8$ metallic glass by high-intensity millisecond laser beam. Our results suggest chemical deposition of atmospheric oxygen and nitrogen in the laser-melted surface area and its surroundings. Zirconium nitride layer was detected in the middle of laser-irradiated area. Nanocrystals embedded in the amorphous matrix were also formed on the surface. Overall, our findings suggest possibilities for improvement of mechanical characteristics of the studied metallic glass.

While sex ratios at birth (SRB) have been shown to vary within and across populations, after over a century of research, explanations have remained elusive. A variety of ecological, demographic, economic, and social variables have been evaluated, yet their association with SRB has been equivocal. Here, in an attempt to shed light on this unresolved topic within the literature, we approach the question of what drives variation in SRB using detailed longitudinal data spanning the frontier-era to the early 20th century in a US population. Using several measures of environmental harshness, we find that fewer boys are born during challenging times. However, these results hold only for the frontier-era and not into a period of rapid industrialization. We argue that the mixed state of the literature may result from the impact and frequency of exogenous stressors being dampened in post-industrial societies.

Molecular modeling studies were carried out at the DFT level of the adsorption of propane and propene on Ag surfaces as a model of the interaction of light hydrocarbons with Ag/ZrO2 catalysts for the catalytic combustion reaction. It was found that the most stable mode of adsorption of propene through its π system on Ag atom has energies consistent with chemisorption and generates an elongation of the C1=C2 bond, which would explain the increase in the activity of the catalysts as function of its metallic charge. The results obtained from the DFT calculations explain the different types of interaction between propene and propane with the metallic surface. The propene is chemisorbed on the Ag surface, distorting its bonds and generating its activation. This would imply that a higher metallic charge in the catalyst would increase the number of active sites in which this activation occurs, generating a higher activity. Besides, with the addition of O, the binding energy between the propene and the metal surface increased. On the other hand, the presence of a metallic surface is not enough for the activation of the propane molecule. This would explain why by increasing the amount of metal in the catalyst, the activity for the combustion of propane is practically not affected

The Rb/Sr ratio of lake sediments has been widely adopted as an indicator of weathering intensity in studies of past climate change, but the geochemical significance of this ratio varies with timescale. Here we present Rb/Sr data for the last 300 years for sediments collected from Chaonaqiu Lake in the Liupan Mountains of the western Chinese Loess Plateau as a decadal-scale record of weathering intensity. To validate the application of this weathering proxy, we correlated the record with those of other major elements, rock-forming minerals, and paleoclimatic proxies. We found that Rb/Sr ratios are influenced mainly by Sr activity within the lake catchment (where Sr is likely sourced from albite). In addition, higher (lower) Rb/Sr ratios of bulk sediments from Chaonaqiu Lake are correlated with lower (higher) fractions of terrigenous detritus (SiO2, Ti, K2O, Al2O3, and Na2O). Lake bulk sediment Rb/Sr ratios are dominated by the input of terrigenous detritus over decadal timescales. Our data show that physical and chemical weathering in Chaonaqiu Lake catchment have opposing influences on bulk sediment Rb/Sr ratios, competing to dominate these ratios of lake sediments over different timescales, with ratios reflecting the relative importance of the two types of weathering. We infer that the Rb/Sr ratios of Chaonaqiu Lake sediments reflect climatic signals of precipitation and temperature over long timescales and of precipitation over short timescales.

This paper presents a new approach of eddy current methods for determining the size of the co-axial hole in the metallic circular disk. In recent decades, for the air-cored sensor probe, the impedance change due to the presence of an infinite metal plate can be calculated by the Dodd-Deeds model. However, in practical measurements, the sample cannot match with the condition required - ‘infinite’, thus the Dodd-Deeds model could not be applied to the disk with finite size and certainly not a co-axial hole in the center. In this paper, a dual-constraint analytical method is proposed. That is, the upper and lower limits of the integration are substituted with specific values instead of the original 0 and . Besides, it is found that, once the outer radius of the disk is fixed (i.e. the lower limit of integration is fixed), the upper limit reduces linearly as the size of the coaxial hole increases. Both the FEM simulation and experiments have been carried out to validate this method. The radius of the hole can be estimated based on the dual-constraint integration feature.

Production of energy is a main task of cancer cells metabolism, since costs of duplicating are enormous. Although energy is derived in cells by dismantling carbon to carbon bonds of any macronutrient, cancer nutritional needs for energetic purposes have been studied primarily as dependent on glycolysis. Since the end of the last century, awareness of dependence of cancer metabolism on amino acids not only for protein syntheses but also for matching energy needs has grown. The roles of specific amino acids, like glutamine, glycine and serine have been explored in different experimental conditions and reviewed. Moreover, there are epidemiological evidences that some amino acids used as supplement for therapeutic reasons (the branched chain ones) may reduce incidence of liver cancer, and some molecular mechanism has been proposed as functional to their protective action. On the contrary, metabolic signature of some pathology connected with increased risk of cancer, like prolonged hyperinsulinemia in insulin resistant patients, is signed by plasma elevated levels of the same branched chain amino acids, posing puzzling questions to clinicians. Most recently, peculiar formulations of amino acids, deeply different if compared to amino acids compositions normally present in foods, have shown the power to master epigenetics slowing growth or driving cancer cells to apoptotic death, while being even beneficial for normal cells and for animals health and life span. In this review, we will analyze and try to disentangle some of the many knots dealing with complexities of amino acids biology and linked to cancer metabolism.

Hepatocellular carcinoma (HCC) early diagnosis is challenging. Moreover, for patients with al-pha-fetoprotein (AFP)-negative HCC, this challenge is augmented. MicroRNAs (miRs) profile may serve as potential HCC molecular markers. We aimed to assess plasma homo sabines (hsa)-miR-21-5p, hsa-miR-155-5p, hsa-miR-192-5p, hsa-miR-199a-5p expression levels, as panel of biomarkers for HCC in chronic hepatitis C virus (CHCV) patients with liver cirrhosis (LC), es-pecially AFP-negative HCC cases, a step toward non-protein coding (nc) RNA precision medicine. Subjects and Methods: 79 patients enrolled with CHCV infection with LC, subclassified into LC group without HCC (n=40) and LC with HCC (n=39) in comparison with 15 apparently healthy control subjects. Real-time quantitative PCR was used to measure plasma hsa-miR-21-5p, hsa-miR-155-5p, hsa-miR-192-5p, and hsa-miR-199a-5p. Results: Plasma hsa-miR-21-5p and hsa-miR-155-5p demonstrated significant upregulation, while hsa-miR-199a-5p demonstrated significant downregulation in the HCC group (n=39) when compared to LC group (n=40). Hsa-miR-21-5p expression was positively correlated with serum AFP, insulin, and insulin re-sistance (r=0.5, p<0.001, r=0.334, p=0.01, and r=0.303, p=0.02, respectively). According to the ROC curves, for differentiating HCC from LC, combining AFP with each of hsa-miR-21-5p, hsa-miR-155-5p, and miR199a-5p improved the diagnostic sensitivity to 87%, 82%, and 84%, re-spectively, vs 69% for AFP alone, with an acceptable specificity of 77.5%, 77.5%, and 80%, respec-tively, and AUC= 0.89, 0.85, and 0.90, respectively vs. 0.85 for AFP alone. Hsa-miR-21-5p/hsa-miR-199a-5p and hsa-miR-155-5p/hsa-miR-199a-5p ratios discriminated HCC from LC at AUC=0.76 and 0.71, respectively, with sensitivities=94% and 92%, and specifici-ties=48% and 53%, respectively. Upregulation of plasma hsa-miR-21-5p was considered as an independent risk factor for HCC development [OR=1.198(1.063–1.329), p=0.002]. Conclusion: Combining each of hsa-miR-21-5p, hsa-miR-155-5p, and hsa-miR-199a-5p with AFP made possi-ble to identify HCC development in LC patients’ cohort with higher sensitivity than using AFP alone. Hsa-miR-21-5p/hsa-miR-199a-5p and hsa-miR-155-5p/hsa-miR-199a-5p ratios are poten-tial HCC molecular markers for AFP-negative HCC patients. Hsa-miR-21-5p was linked to insu-lin metabolism in HCC patients’ group as well as being an upregulated independent risk factor for the emergence of HCC from LC in CHCV patients.