In the proposed article, the issues of increasing the synchronizing ability of the system of coordinated rotation of asynchronous motors are considered. Based on the T-shaped equivalent circuit, electromechanical relationships were obtained with changes in the value of the total rotor resistance and the supply voltage of individual motors. An algorithm for calculating the torques, stator and rotor currents of the motors of the system has been compiled. Based on the calculations obtained, the mechanical characteristics of the system asynchronous motors are constructed for various values of total resistance, supply voltages and rotor positions. The obtained data and graphs confirm the adequacy of the theory obtained in an analytical way. Functional and structural diagrams in small scales have been compiled, which allow simulating transient operation modes of multi-motor asynchronous electric drives in the Matlab application package. Multi-motor asynchronous electric drives with adjustable supply voltages, as well as with preliminary synchronization and synchronous braking, have been developed. Compilation of a program for the stability of a nonlinear system of a multi-motor asynchronous electric drive (MAEDs) with a thyristor voltage converter (TVC) in Matlab. Also, the modes of soft start, load shedding and surge on the motor shaft are simulated, confirming the stability of the system.

CAMx-LPiG (Comprehensive Air Quality Model with Extensions – Linear Plume in Grid) is an online hybrid model, based on the Chemistry and Transport Model (CTM) CAMx, that includes a sub-grid scale module to simulate the dispersion of linear road traffic emissions, called LPiG. LPiG is a plume in grid module specifically developed by extending the capabilities of the Lagrangian puff sub-grid model available in CAMx. The online integration of the local scale model within the Eulerian CTM allows for a multiscale simulation of air quality from the regional scale to the urban scale, preserving a coherent description of the chemical state of the atmosphere at all spatial scales and avoiding any double counting of the emissions simulated by the sub-grid module. In this work the model is presented and evaluated against measured NO2 concentrations for the city of Milan for the month of January 2017. The model is able to introduce road traffic induced gradient in NO2 concentration at sub-grid resolution. Moreover, CAMx-LPiG is shown to reduce the bias compared to CAMx stand-alone simulations.

Due to the optical properties of the Electron Transport Layer (ETL) and Hole Transport Layer (HTL), inverted perovskite solar cells can perform better than traditional perovskite solar cells. It is essential to compare both types to understand their efficiencies. In this article, we studied inverted perovskite solar cells with NiOx/CH3NH3Pb3/ETL (ETL = MoO3, TiO2, ZnO) structures. Our results showed that the optimal thickness of NiOx is 80 nm for all structures. The optimal perovskite thickness is 600 nm for solar cells with ZnO and MoO3, and 800 nm for those with TiO2. For the ETLs, the best thicknesses are 100 nm for ZnO, 80 nm for MoO3, and 60 nm for TiO2. We found that the efficiencies of inverted perovskite solar cells with ZnO, MoO3, and TiO2 as ETLs, and with optimal layer thicknesses, are 30.16%, 18.69%, and 35.21%, respectively. These efficiencies are 1.5%, 5.7%, and 1.5% higher than those of traditional perovskite solar cells. Our study highlights the potential of optimizing layer thicknesses in inverted perovskite solar cells to achieve higher efficiencies than traditional structures.

The decarbonization of the electricity grid as one among the actions to reduce fossil fuel emissions, and thus their impact on global warming in the future, will be achieved mainly via the integration and widespread diffusion of renewable power sources. This is going to be supported also by the shift from the paradigm production-transmission-distribution, where electricity production oversees large-size power plants, to renewable-based distributed/diffused production, where electricity is generated very close or even by the same (group of) user(s) (or prosumers in the latter case). The number of mid-/small-size installations based on renewable energy technologies will therefore increase substantially, and the related renewable generation will be dominant against that from large-size power plants. Unfortunately, this will reduce the reliability of the grid very likely, unless appropriate countermeasures are taken/implemented, hopefully at the same time the paradigm shift is being achieved. To this aim, it is important to identify the anomalies and main fault causes that might determine in renewable-based power systems. This paper surveys the current state-of-the-art on anomalies and faults affecting wind-PV-storage hybrid power systems, i.e., the main renewable technology ensemble that will establish the future grid, and highlights possible research directions that may help to fill the literature gaps.

A portable laser photoacoustic sensor based on a Field-Programmable Gate Array (FPGA) is reported for methane detection. A tunable DFB diode laser in the 1654 nm wavelength range is used as an excitation source. The photoacoustic signal processing was implemented by a FPGA device. A small resonant photoacoustic cell is designed. The minimum detection limit (1σ) of 10 ppm for methane (CH₄) is demonstrated.

Ruminant animals naturally emit methane gas owing to anaerobic microbial fermentation in the rumen, and these gases are considered major contributors to global warming. Scientists worldwide are attempting to minimize methane emissions from ruminant animals. Some of these attempts include the manipulation of rumen microbes using antibiotics, synthetic chemicals, dietary interventions, probiotics, propionate enhancers, stimulation of acetogens, manipulation of rumination time, vaccination, and genetic selection of animals that produce low methane (CH4). The majority of synthetic additives are harmful to both beneficial rumen microbes and the host or only temporarily affect methanogenesis. Phytogenic feed additives (PFAs) have recently emerged as the best alternatives to antibiotics and synthetic chemicals because of growing public concerns regarding drug resistance and the negative impacts of antibiotics and synthetic chemicals on humans, livestock, and the environment. These additives reduce methane production and improve the volatile fatty acid profile. In this review, we provide an overview of PFA sources and how their bioactive components affect the rumen microbiome to reduce methane emissions. Additionally, we highlight the mechanisms of action of PFAs as a whole as well as some of their bioactive components.

Based on literature data, an analysis was conducted on the thermodynamic and kinetic dependencies of the thermal decomposition of methane. Course of this process was analysed for both thermal and thermal-catalytic conditions. The elementary reaction, i.e. the synthesis of methane from its elements, including its reversibility, was used as the basis for the for considerations on the kinetic model. The conversion degree was adopted as the kinetic parameter (kinetic variable) since this measure is essential for determining the amount of carbon deposit formed and thus closing the mass balance of this process. Several different kinetic models for the elementary reaction were analysed to determine how do they relate in regard to the constant of the reaction rate. It was determined that regardless of whether the process is catalytic or purely thermal, for temperatures t>900°C, the influence of reversibility of the reaction, has negligible influence on the yield of hydrogen produced, and thus can be omitted from the kinetic models. Special attention was given to iron-based catalysts, analysing the reactivity of Fe/C systems. It was demonstrated that the determined kinetic parameters satisfy the Kinetic Compensation Effect (KCE). Furthermore, by incorporating elements of Transition State Theory (TST), the existence of Entropy-Enthalpy Compensation (EEC) was highlighted. Based on these findings Authors show that through analysis of the changes in activation energy (E=20–421 kJ·mol-1) only an estimate of the optimal process conditions can be found, because the isoconversional temperature is also dependent on the way in which the reaction is conducted (T_{iso}=1200-1450K\ >\ \ T_{eq}). In other words, it was found that strong influences of such factors as T, P, etc. can locally compensate each other. Finally, it was also shown that the relations between KCE and EEC complement each other, which is confirmed by the determined average activation entropy at the isokinetic temperature (∆SB= -275.0 J·(mol·K)-1).

Source water quality is a key determinant of drinking water quality. The recast European Union 2020/2184 drinking water directive (DWD) introduced the obligation for comprehensive risk assessment in drinking water supplies, including the water source and incorporated new elements of natural origin in the list of parameters to be monitored. The current study is the first comprehensive assessment of 15 natural elements (B, Ba, Be, Ca, Co, K, Li, Mg, Mo, Na, Se, Sr, Ti, U and V) in 1155 (82%) Hungarian drinking water sources, including surface water, bank filtered and groundwater sources. Parameters posing a risk to health (Se, V and U) were typically below the lower limit of quantification (LOQ), but higher concentrations (max. 7.0, 17 and 41 µg/L, respectively) may occur in confined locations, the latter exceeding the DWD parametric value in one water supply. Li in a small geographical area, Mg and Ca in the majority of the water supplies reached the concentration range assumed to be protective to health. Water sources were grouped in 6 clusters based on their element distribution, some of them also showing clear geographical patterns. Water types were not differentiated, with the exception of karstic waters (dominated by Ca and Mg). None of the investigated parameters are expected to be a source of public health concern.

Fungi inhabiting deep subseafloor sediments have been shown to possess anaerobic methane (CH₄) production capabilities under atmospheric conditions. However, their ability to produce CH₄ under in situ conditions with high hydrostatic pressure (HHP) remains unclear. Here, Schizophyllum commune 20R-7-F01, isolated from ~ 2 km below the seafloor, was cultured in Seawater Medium (SM) in culture bottles fitted with sterile syringes for pressure equilibration. Subsequently, these culture bottles were transferred into 1-liter stainless steel pressure vessels at 30 °C for 5 days to simulate in situ HHP and anaerobic environments. Our comprehensive analysis of bioactivity, biomass, transcriptomics revealed that S. commune not only survived but significantly enhanced CH₄ production, reaching approximately 2.5 times higher levels under 35 MPa HHP compared to 0.1 MPa standard atmospheric pressure. Pathways associated with carbohydrate metabolism, methylation, hydrolase activity, cysteine and methionine metabolism, and oxidoreductase activity were notably activated under HHP. Specifically, key genes involved in fungal anaerobic CH₄ synthesis, including methyltransferase mct1 and dehalogenase dh3, were upregulated 7.9- and 12.5-fold, respectively, under HHP. Enhanced CH₄ production under HHP was primarily attributed to oxidative stress induced by pressure, supported by intracellular Reactive Oxygen Species (ROS) levels and comparative treatments with cadmium chloride and hydrogen peroxide. These findings suggest that fungi persisting in deep-sea sediments over millions of years have the potential to significantly contribute to global CH₄ flux.

This study presents a comprehensive approach to calculating the free energy of hydration of methane using Molecular Dynamics simulations. We employed the Free Energy Perturbation (FEP) method to determine the Gibbs free energy associated with transferring a methane molecule into water. Simulations were conducted in a cubic simulation box containing one methane molecule and 1000 TIP4P water molecules. The forward and backward routes were both analyzed, providing consistent free energy differences, which validates the robustness of our methodology. The Gibbs free energy profiles demonstrated characteristic energy barriers and stabilization points, indicative of the interaction dynamics in the solvation process. The results demonstrate the robustness of the FEP method implemented in LAMMPS, yielding free energy in close agreement with experimental data and previous computational studies. The calculated free energy differences for methane hydration exhibited deviations of 13% and 8% for the forward and backward routes, respectively, compared to experimental values. These findings underscore the accuracy and efficiency of using LAMMPS for free energy calculations, contributing to the broader understanding of solvation thermodynamics. Additionally, radial distribution functions were analyzed to provide insights into the structural arrangement of water molecules around methane, revealing strong interaction between methane's carbon atom and water molecules.

The effect of H2S with high concentrations on catalytic dry reforming of methane (DRM) process has seldom been focused on previously. Herein, a thermodynamic analysis of the DRM reactions in the presence of H2S with the concentration varying in 0-20 vol% was conducted firstly. Several typical types of catalysts including MgO, NiO/MgO and LaNiO3 in different states were prepared for executing DRM at 800 C, 0.1 MPa in the feed of 20 vol% CO2 and 20 vol% CH4 balanced with N2. The catalytic performance of each catalyst for DRM process under conditions of absence and presence of H2S was compared. A promotion effect of increasing H2S concentration on both the conversions of CO2 and CH4 and the molar yields of CO and H2 was observed on all the catalysts especially the MgO and the pristine NiO/MgO. While a significant decline in catalytic activity of either the reduced NiO/MgO or the reduced LaNiO3 catalyst after adding H2S, moderate reactant conversions still sustained. The results of process analysis and catalyst structure characterization suggest that H2S participation can contribute to the increment in CO2 and CH4 conversion, and active S-adsorbed species may play the key role of catalysis in the reactions involving H2S.

Accurate assessment of shale gas reserves hinges on a detailed characterization of gas and water distribution within shale reservoirs. Despite its importance, the nanoscale behavior of water and methane in deep shale formations, especially under elevated temperatures and pressures, remains poorly understood. This study proposes a novel molecular modeling approach to represent the complex nanocomposite porous media found in deep shale matrices. Leveraging quantitative data from experimental analyses of shale pore composition, we developed a molecular model that accurately reflects the intricate pore-slit structure within a composite of kerogen and illite, common constituents of shale. Employing a hybrid grand canonical Monte Carlo and molecular dynamics simulation technique, we investigated the micro-scale distribution and preferential adsorption sites of water and methane within the shale matrix. Our research further elucidates the impact of water on the pore structure of shale and delineates the co-occurrence patterns of water and methane. The simulations reveal that water and methane share similar adsorption preferences on kerogen surfaces, while methane does not exhibit specific adsorption preferences on water-bearing illite. We also find that the presence of water significantly alters the illite pore space, leading to a reduction in larger pore volumes and a concomitant increase in smaller pores. The decrease in methane content with increasing water content is more pronounced in the shrinkage cracks compared to the kerogen matrix pores and is particularly notable in the macropores of illite. The findings underscore the differential sensitivity of methane content to water levels across various shale pore types. These insights contribute to a deeper theoretical understanding of gas and water distribution mechanisms in deep shale reservoirs, offering valuable support for the evaluation of deep shale gas resource potential.

The general synthesis of boron-containing cyclic compounds (boracycles) necessitates toxic organotin precursors or highly reactive boron halides. Here we report the synthesis of seven- and five-membered boracycles utilizing arylboronic acid pinacol esters (ArBpins) as stable boron sources. Grignard reagents generated from 2,2′-dibromodibenzyl or 2,2′-dibromobiphenyl reacted with ArBpins, where Ar = 9-anthryl (Anth), 2,4,6-trimethylphenyl (Mes), 2,4,6-triisopropylphenyl (Tip), to give 10,11-dihydro-5H-dibenzo[b,f]borepins or dibenzoborole derivatives. This Bpin-based method was successfully applied to a one-shot double boracycle formation, providing a dihydrodibenzoborepin–anthracene–dihydrodibenzoborepin triad molecule in a good yield. The dihydrodibenzoborepin bearing the Anth group was directly converted to the unsaturated borepin by NBS/AIBN. All products were characterized by NMR, HRMS, and in some cases, single-crystal X-ray diffraction analysis. Additionally, the photophysical properties of the products are also reported.

Abstract: High step-up voltage gain nonisolated DC-DC converter have attracted much attention in photovoltaic, fuel cells and other renewable energy system applications. In this paper, by combining input current ripple-free boost cell with coupled-inductor voltage-doubler cell, an input current ripple-free high voltage gain nonisolated converter is proposed. In addition, passive lossless clamp circuit is adopted to recycle the leakage inductor energy and to reduce the voltage spike across the power switch. By utilizing voltage-doubler cell consisting of diode and capacitor, the voltage stress of switch is further reduced and the resonance between the leakage inductor and the stray capacitor of the output diode is eliminated. A low switch-on-resistance low-voltage-rated MOSFET can therefore be employed to reduce the conduction loss and cost. The reverse recovery loss of output diode is reduced, and the efficiency of converter can be improved. Furthermore, the proposed converter can achieve nearly zero input current-ripple and make the design of electromagnetic interference (EMI) filter easy. Steady state analysis and operation mode of the converter is performed. Finally, experimental results are presented to verify the analysis results of the proposed converter.

This review paper presents a comprehensive synthesis of current knowledge on the contamination of water systems by polycyclic aromatic hydrocarbons (PAHs). PAHs, organic contaminants characterized by two or more fused aromatic rings, are notably problematic due to their persistence, bioaccumulation, and significant health risks. The review commences with an examination of various sources of PAHs in aquatic environments, encompassing both anthropogenic activities, such as industrial discharges, urban runoff, and oil spills, and natural phenomena including volcanic eruptions and wildfires. Subsequently, the discussion shifts to the distribution patterns of PAHs within different aquatic ecosystems, with an analysis of factors that influence their transport. Considerable focus is placed on the entry mechanisms of PAHs into water systems and their interactions with diverse environmental matrices. Additionally, the ecotoxicological effects of PAHs on aquatic life are scrutinized, with particular emphasis on molecular, individual, and ecosystemic impacts. This includes an exploration of PAH bioaccumulation in aquatic organisms and their potential mutagenic and carcinogenic consequences. The review further addresses the challenges associated with detecting and quantifying PAHs in aquatic settings, reflecting on the advancements in analytical methodologies and the complexities introduced by their varied physicochemical properties. The paper concludes with a summary of existing regulatory frameworks and guidelines governing PAH contamination in water systems, underscoring the imperative for global collaboration in the monitoring and management of PAH pollution.

Most empirical work on sources of economic growth for different countries lack country-specific empirical evidence to guide policy choices in individual developing countries and previous studies of factor productivity tend to focus on the entire economy or a single sector. In this study, we use the recently developed growth accounting tools to explicitly determine the sources of economic growth at both national and sectoral levels in Zambia between 1970 and 2013. We use data from World Development Indicators and Zambia’s Central Statistical Office. On average, total factor productivity (TFP) contributes about 5.7% to economic growth. Sectoral analysis shows that agriculture contributes the least to GDP and that within each sector; factors that contribute to growth differ. Structural transformation has been slow and contributed to the observed inefficiency. We outline the implications of the observed growth and provide recommendations.

Multiple sources influence air quality and regional climate in complicated atmospheric emission situations like urban agglomerations. To resolve pollution plumes and source influences in polluted areas, a comprehensive chemical fingerprinting of sources utilizing non-methane hydrocarbons (NMHCs) and the identification of acceptable tracer molecules and emission ratios is required, in contrast to pristine locations, where reliance on a single or a few chemical tracers is frequently sufficient. We have characterized the prevalence of NMHCs fingerprints in the urban areas and quantified the correlation of windspeed with the concentration of these pollutants. eNose sensors and Air quality management stations provide the data to identify the emission sources of such pollutants. Based on our analysis, the average NMHC concentration in 2021 has been recorded 0.424 ppm at point 1 AQMS whereas at point 2 AQMS it was 0.256 ppm. Such outcomes could be attributed to the proximity of emissions sources, the direction and speed of the wind, or both. Moreover, traffic can be a major contributor to pollution levels in any urban area. More research based on a larger dataset is required before definitive conclusions can be drawn, and viable solutions can be proposed.

Due to its high short-term global warming potential (GWP) compared to carbon dioxide, methane (CH₄) is a considerable agent of climate change. This research is aimed at analyzing data on methane gathered at the GAW (Global Atmosphere Watch) station of Lamezia Terme (Calabria, Southern Italy) spanning seven years of continuous measurements (2016-2022) and integrating the results with key meteorological data. Compared to previous studies on detected methane mole fractions at the same station, daily-to-yearly patterns have become more prominent thanks to the analysis of a much larger data set. Overall, the yearly increase of methane at the Lamezia Terme station is in general agreement with global measurements by NOAA, though local peaks are present, and an increase linked to Covid-19 is identified. Seasonal changes and trends have proved to be fully cyclic, with the daily cycles being largely driven by local wind circulation patterns and synoptic features. Outbreak events have been statistically evaluated depending on their weekday of occurrence to test possible correlations with anthropic activities. A cross analysis between methane peaks and specific wind directions has also proved that local sources may be deemed responsible for the highest mole fractions.

Hydrogen and carbon monoxide over-equilibria have been found computationally in kinetic dependencies of methane reforming catalytic reactions (steam and dry reforming) using conditions of the conservatively perturbed equilibrium (CPE) phenomenon, i.e. at the initial equilibrium concentration of hydrogen or carbon monoxide.  The influence of pressure, temperature, flow rate and composition of the initial mixture on the position of the CPE point (the extremum point) was investigated in a wide domain of parameters. It is demonstrated that the CPE phenomenon significantly increases the product concentration (H2 and CO) at the reactor length which is significantly less than the reactor length required to reach the equilibrium. The CPE-point was interpreted as the “turning point” in kinetic behavior.  Recommendations on the temperature and pressure regimes are different from the traditional ones related to the Le Chatelier’s law. Obtained results provide valuable information on optimal reaction conditions for complex reversible chemical transformations, offering potential applications in chemical engineering processes.

This study investigates the impact of thin flame combustor design on hydrogen flame characteristics and combustion performance through numerical simulations. Variations in flame shape and combustibility between 100% methane and 100% hydrogen combustion are analyzed. Three combustor header shapes (flat, concave, and convex) are modeled to assess their influence on flame behavior. Results show distinct flow patterns, with concave headers promoting strong central flows and convex headers dispersing the flow outward. Temperature field analysis indicates that hydrogen flames have higher temperatures and shorter quenching distances compared to methane flames. A comparative analysis of combustion products is conducted to evaluate combustion performance and NOx emissions. Consequently, the concave header has high combustibility and increases temperatures and NOx fraction in hydrogen combustion.

The permanent protection of groundwater and surface sources of drinking water in the required raw water quality from contamination is the primary foundation of preserving the life of society and the entire engineering infrastructure operability not only in the Czech Republic but also in other countries of the world. One of the basic ways of contamination prevention enhancement and risk mitigation of putting a water source out of operation is the identification of the given risk as well as soil contamination monitoring. The purpose of this study is to understand specific aspects of contamination threats to drinking water sources and determine possible solutions to eliminate the risk, shown in the example case study in the Czech Republic conditions. Based on the findings, a proposal to enhance the prevention of water source contamination has been elaborated in the form of recommendations regarding the ways and means used to monitor the risk areas and to implement technical measures so as to eliminate or terminate the specified risk. A complex approach based on the integration of interdisciplinary factors and methodology is required to minimize the threats of aquatic ecosystems contamination in the Czech Republic.

This research project aimed to address the growing concern about methane emissions from seaweed by developing a Convolutional Neural Network (CNN) model capable of accurately predicting these emissions. The study used PANDAS to read and analyze the dataset, incorporating statistical measures like mean, median, and standard deviation to understand the dataset. The CNN model was trained using the ReLU activation function and mean absolute error as the loss function. Model performance was evaluated through MAPE graphs, comparing the mean absolute percentage error (MAPE) between training and validation sets and between true and predicted emissions, and analyzing trends in yearly greenhouse gas emissions. The results demonstrated that the CNN model achieved a high level of accuracy in predicting methane emissions, with a low MAPE between the expected and actual values. This approach should enhance our understanding of methane emissions from Sargassum, contributing to more accurate environmental impact assessments and effective mitigation strategies.

The paper explores the features of numerical simulation to analyze the dynamic behavior of drives controlled by pulse-width modulators. Modern motor control systems widely use pulse width modulation. Effective numerical modeling of such systems has specific features because the models employed are continuous-event and have hybrid behavior due to the presence of nonlinear links with discontinuities of the first kind. Therefore, it is essential to have special integration methods with variable steps, which should be factored in when developing the model. The paper shows how these problems are solved when modeling an electric drive with a DC motor in the SimInTech software.

Saprotrophic fungi are key in global carbon cycling, capable of decomposing lignocellulose in wood. This study, for the first time, explores the influence of oxygen (O2) and temperature on methane (CH4) production by two fungi, Laetiporus sulphureus and Pleurotus sapidus. We examined CH4 formation under varying O2 levels (0 to 98%) and temperatures (17, 27, and 40 °C) when the fungi grew on pine wood, beech wood, and grass under sterile conditions. Our findings reveal a strong dependency of fungal CH4 production on O2 mixing ratios. Methane formation was highest when O2 levels exceeded 5%, whilst no CH4 formation was observed after complete O2 consumption by the fungi. Reintroducing O2 immediately resumed fungal CH4 production. When CH4 formation was normalized to O2 consumption (CH4_norm) a different pattern between species was observed. L. sulphureus showed higher CH4_norm rates with higher O2 levels, whereas P. sapidus showed elevated rates between 0-5% O2. Temperature also significantly influenced CH4 and CH4_norm rates, with the highest production at 27 °C, and comparatively lower rates at 17 and 40 °C. These results demonstrate that O2 levels and temperature are critical in controlling fungal CH4 emissions, a consideration necessary for future CH4 source predictions.

As an important element of methane prevention in mining facilities, measurements of concentration serve to obtain information about methane hazards. Information about methane concentration must be linked to the place and time of its occurrence to create valuable data for ongoing hazard analysis. The article presents the results of a methane hazard analysis based on an airflow and methane concentration model, validated using measurement data. Subsequently, simulations of crew movement and the operation of individual methane detectors working according to the algorithms of the Methane Hazard Detection System were conducted based on this model.

Background/Objectives: Women's reproductive and overall well-being are intricately associated to vitamin D levels. In Morocco, vitamin D deficiency is a major issue for premenopausal women, yet little data exists on their dietary intake of this nutrient. This study explores vitamin D dietary intake, socio-demographic determinants, and its correlation with serum 25-hydroxyvitamin D [25(OH)D3] in premenopausal Moroccan women. Methods: A cross-sectional study was conducted with 355 women aged 18-49 in Meknes, Morocco, using validated questionnaires to assess dietary intake and sun exposure. Potential covariates such as physical activity and BMI were also assessed . Serum 25(OH)D was measured via chemiluminescence immunoassay. Chi-square tests and Spearman correlation were used to identify socio-demographic factors influencing vitamin D intake. Linear and multivariate regression analysis determined the main predictors of serum 25(OH)D levels. Results :The median (interquartile range) vitamin D dietary intake was 2.8 (2.7) µg/day , with less than 20% of women meeting the recommended 5 µg/day. Major dietary sources were fish (48%), dairy (24.3%), and meat (9.4%), with fortified foods contributing only for 7%. Lower intake was linked to younger age (p=0.004) and rural living (p=0.024). While no significant association was found between dietary intake and serum 25(OH)D ((β(SE): 0.155(0.094), p=0.340 ) , sun exposure positively predicted serum levels(β(SE): 0.343 (0.128), p=0.008) , and BMI negatively affected them (β(SE): -1.128 (0.337), p=0.001). Conclusions: Our findings highlight insufficient vitamin D intake among premenopausal Moroccan women, especially younger and rural women. Nutritional interventions are needed to address this deficiency, promoting better dietary habits, sun exposure, and healthy weight.

Few studies have examined the dietary protein intake and sources in combination with the longitudinal changes in brain structure markers. Our study aimed to examine the association between dietary protein intake and different sources of dietary protein with the longitudinal rate of change in brain structural markers. A total of 2723 and 2679 participants from the UK Biobank were included in the analysis. The relative and absolute amounts of dietary protein intake were calculated through a 24-hour dietary recall questionnaire. The longitudinal change rates of brain structural biomarkers were computed using two waves of brain imaging data. We utilized multiple linear regression to examine the association between dietary protein and different sources and the longitudinal changes in brain structural biomarkers. Restrictive cubic splines were used to explore nonlinear relationships, and stratified and sensitivity analyses were conducted. Increasing the proportion of animal protein in dietary protein intake is associated with a slower reduction in the total hippocampus volume (THV, β: -0.02524, P<0.05), left hippocampus volume (LHV, β: -0.02435, P<0.01) and right hippocampus volume (RHV, β: -0.02544, P<0.05).Higher intake of animal protein relative to plant protein is linked to a lower atrophy rate in THV (β: -0.01249, P<0.05) and LHV (β: -0.01173, P<0.05) and RHV (β: -0.01193, P<0.05). Individuals with higher intake of seafood exhibit lower longitudinal rate of change in HV compared to those with no consume (THV, β: -0.004514; P<0.05; RHV, β: -0.005527, P<0.05). In subgroup and sensitivity analyses, there was not a significantly alteration. A moderate increase in the intake and proportion of animal protein in the diet, especially from seafood, is associated with a lower longitudinal change rate in hippocampus volume.

Keywords: contamination; bioaccumulation; fish and mollusks tissue; ecosystem components; heavy metals; organochlorine pesticides; polychlorinated biphenyls; polycyclic aromatic hydrocarbons.

The substitution of chemical fertilizers by organic manure plays a critical role in sustainable crop production. Nevertheless, organic amendments promote the global warming potential (GWP) in rice paddies due to increased methane (CH4) emissions. Increasing evidence shows that lime application can reduce CH4 emissions from acidic paddy soils, while it is still not clear whether liming can reduce the GWP in rice fields under organic manure substitution. A two-year field experiment was conducted to investigate the impacts of pig manure substitution and lime application on grain yield, CH4 and nitrous oxide (N2O) emissions in a subtropical double-cropped rice field in China. The experiment consisted of three treatments: chemical fertilization (CF, 100% N from urea), 50% of chemical N substituted by pig manure (1/2N + M), and the 1/2N + M treatment plus lime amendment (1/2N + M + L). On average, 1/2N + M reduced rice yield by 5.65% compared to CF, while lime application had no effect on rice yield. Mean cumulative CH4 emissions were 218.8% higher in 1/2N + M than in CF, whereas 1/2N + M + L reduced CH4 emissions by 36.6% compared to 1/2N + M. Neither pig manure substitution nor lime application affected N2O emissions. Consequently, 1/2N + M increased the GWP and greenhouse gas intensity (GHGI) by 214.6% and 228.3%, respectively, compared to CF. In contrast, 1/2N + M + L reduced the GWP and GHGI by 36.4% and 36.5% compared to 1/2N + M. Lime application can mitigate CH4 emissions and GWP induced by pig manure amendment in double-cropped rice fields.

In order to investigate the size distributions and seasonal variations of carbonaceous aerosols (OC and EC), the carbonaceous species were collected and then analyzed by using a 9-stage Anderson-type aerosol sampler and DRI Model 2001A Thermal/Optical Carbon Analyzer on the typical industrial city Nanjing in Yangtze River Delta, China in the summer, autumn and winter of 2013 and spring of 2014. OC, EC, SOC and POC exhibited obvious seasonal variations, with the highest level in winter (39.1±14.0, 5.7±2.1, 23.6±11.7 and 14.1±5.7 μg•m^-3) and the lowest level in summer (20.6±6.7, 3.3±2.0, 12.2±3.8 and 8.4±4.1 μg•m^-3), and were mainly centralized in PM_1.1 in four seasons. The concentrations of OC in PM_1.1 varied in the order of winter > autumn > spring > summer, while EC ranked in the order of autumn > winter > summer > spring. In the PM_1.1-2.1 and PM_2.1-10, the concentrations of OC and EC decreased in the sequence of winter > spring > autumn > summer. The size spectra of OC, EC and SOC had bimodal distributions in four seasons, except for EC with four peaks in summer. The size spectra of POC varied greatly with seasons, exhibiting bimodal distribution in winter, trimodal distribution in spring and summer, and four peaks in autumn. The OC/EC ratios were 7.0, 6.3, 7.6 and 6.9 in spring, summer, autumn and winter, respectively, which demonstrated the abundance of secondary organic aerosols in Nanjing. The sources of carbonaceous aerosol varied significantly with seasons, and were dominated by vehicle exhaust, coal and biomass burning in PM_2.1, and dominant by dust, coal and biomass burning in PM_2.1-10.

Integrated nutrient management (INM) is an approach that optimizes the benefits derived from various nutrient sources and beneficial soil microorganisms in an integrated manner to increase crop productivity while maintaining soil fertility. An open-field experiment was conducted at Cabuyao, Laguna, Philippines to investigate the effects of combining chemical fertilizers, vermicompost, arbuscular mycorrhizal fungi (AMF), and nitrogen-fixing bacteria (Azospirillum spp.) on the growth, nutrient uptake and yield of tomato. The experiment was arranged in a randomized complete block design replicated four times. The treatments were recommended rate of chemical fertilizer (RRC), combined 50% RRC and 4 t ha-1 vermicompost (INM 1), AMF inoculation with combined nutrient sources (INM 2), and dual inoculation with AMF and Azospirillum in synergy with combined nutrient sources (INM 3). Results revealed that the growth parameters were not significantly affected by the treatments, but the highest data were observed in the treatments under INM. AMF inoculation significantly increased phosphorus, potassium, calcium, and magnesium uptake of tomato while INM 3 recorded the highest nitrogen uptake. Treatments with vermicompost application recorded significantly higher uptake of copper. INM 1, INM 2, and INM 3 gave a significantly higher fruit yield than the RRC with an increase of 7.98%, 13.40%, and 13.65%, respectively. The percentage of mycorrhizal root colonization and number of rhizosphere spores were higher in mycorrhizal plants. Fruit yield and AMF root colonization are positively correlated with uptake of various nutrients. The results imply that these INM strategies can improve growth of tomato, increase fruit yield, reduce the amount of chemical fertilizers applied, and potentially lead to economic, soil health and environmental benefits.

One of the possible mechanisms causing significant emissions of methane into the atmosphere within the Arctic shelf may be the decomposition of gas hydrates. Their accumulations within the Arctic shelf formed during Ice Age almost simultaneously with the formation of permafrost, which contributed to the emergence of a zone of stable existence of gas hydrates. The subsequent flooding of the Arctic shelf led to the degradation of the permafrost and the violation of the conditions for the existence of hydrates. To assess the state of the stability zone, methods of mathematical numerical modeling are used. Standard seismic methods are widely used to localize gas hydrates, but monitoring their physical state requires the development of fundamentally new approaches based on solving multiparameter inverse seismic problems. In particular, the degree of attenuation of seismic energy is one of the objective parameters for assessing the consolidation of gas hydrates: the closer they are to the beginning of decomposition, the higher the attenuation, and hence the lower the quality factor. Thus, the methods of seismic monitoring of the state of gas hydrates in order to predict the possibility of developing dangerous scenarios should be based on solving a multi-parameter inverse seismic problem. This publication is devoted to the presentation of this approach.

Good hand hygiene has proven to be essential in reducing the uncontrolled spread of human pathogens. Cold atmospheric plasma (CAP) may provide an alternative to disinfecting hands with ethanol-based handrubs when hand washing facilities are unavailable. CAP can be safely applied to the skin if the energy is well controlled. In this study, RF and DC plasma sources was built with a pin-to-mesh electrodes configuration inside a fused silica tube of 5 mm of inner diameter. Microbiological assays based on EN 13697:2015+A1:2019 using Escherichia coli DSM 682 or Staphylococcus epidermidis DSM 20044 were used to examine the antimicrobial effect of various plasma conditions. Metal and silicone disks that model skin were used as inoculation matrices. The prototype air radio frequency (RF) CAP achieved significant disinfection in the MHz range on stainless steel and silicone substrates. This is equivalent to half the performance of direct current CAP, which is only effective on conductive substrates. Using only electricity and air CAP could, with further optimization, replace or complement current hand disinfection methods, and mitigate the economic burden of public health crises in the future.

Sustainability of current energy policies and known mid-term policies are analised in their multiple facets. First an overview is given about the trend of global energy demand and energy production, analysing the share of energy sources and the geographic distribution of demand, on the basis of statistics and projections published by major agencies. The issue of sustainability of the energy cycle is finally addressed, with specific reference to systems with high share of renewable energy and storage capability, highlighting some promising energy sources and storage approaches.

Coalbed Methane(CBM) production enhancement for single wells is a big problem to CBM industrialization. Low production is due to insufficient gas generation by thermogenic. Luckily, Biogenic gas was found in many areas and its supply is assumed to improve coalbed methane production. Therefore, microbial simulation experiment will demonstrate the effectiveness of the assumption. From microbial simulation experiment on different coal ranks, it is found that microbes can use coals to produce biogas under laboratory conditions. With different temperatures for different experiments, it turns out that the gas production at 35 ℃ is greater than that at 15℃,indicating that 35℃ is more suitable for microbes to produce gas. According to quantitative experiments, adding exogenous nutrients or exogenous bacteria can improve CBM production. Moreover, the production enhancement ratio can reach up to 115% under the condition of adding exogenous bacterial species, while the ratio for adding nutrients can be up to 144%.

Purpose. This paper aims to present a unique perspective that emphasizes the intricate interplay between energy, dietary proteins, and amino acid composition, underscoring their mutual dependence for health-related considerations. Energy and protein synthesis are fundamental to biological processes, crucial for the sustenance of life and growth of organisms. Methods and Results. We explore the intricate relationship between energy metabolism, protein synthesis, regulatory mechanisms, protein sources, amino acid availability, and autophagy, in order to elucidate how these elements collectively maintain cellular homeostasis. We underscore the vital role this dynamic interplay has in preserving cell life. Conclusion. A deeper understanding of the link between energy and protein synthesis is essential to comprehend fundamental cellular processes. This insight could have wide-ranging impact in several medical fields, such as nutrition, metabolism, and disease management.

More than 700 anthocyanins are described so far, and many different sources are rich in these natural pigments. During the last few years, researchers have been focusing of strategies to recover and purify anthocyanins, from simple liquid-liquid extractions to more advanced supercritical CO2 extractions, however, with such a huge number of different sources, it’s extremely hard to get a simple and fast methodology that fits several sources, not only by the structural nature of the anthocyanins but also by the presence of specific groups of natural compounds. Using simple methodologies like solid-phase extraction resins represents a powerful economical and efficiency strategy. In this work, we tested several sources of structurally distinct anthocyanins, including purple basil, purple cabbage, purple sweet potato, butterfly pea flower, cornflower and wild pansy, in different resins to assess their efficiency in the obtention of anthocyanin-pure extracts. The results showed us that the combination of oasis HLB® resin followed by a cation-exchange SPE with DSC-MCAX® resulted in high-purity anthocyanin extracts for all the cases.

Background: Disparity in adult mortality (AM) with reference to social dynamics and health care has not been sufficiently examined. This study aimed to identify the gap in the understanding of AM in relation to religion, political stability, economic level, and universal health coverage (UHC). Methods: A cross-national study was performed with different sources of data, using the administrative record linkage theory. We created a new data set using data from the 2013 World Bank data catalogue by region, The Economist (Political instability index 2013), Stuckler David et al. (Universal health coverage, 2010), and religious categories of all UN country members. Descriptive statistics, a t-test, an ANOVA followed by a post hoc test, and a linear regression were used where applicable. Result: The average AM rate for males and females was 0.20 ± 0.10 and 0.14 ± 0.10, respectively. AM was significantly higher in economically weak countries, countries with political instability, countries with traditional religion, without achievement of UHC, and Sub-Saharan Africa (p<0.01). There was high disparity of AM between countries with and without UHC (F = male: 61.89, female: 51.85, p<0.001) and between groups with low and high income (F = male: 36.33, female: 42.39, p<0.001). UHC and political stability would significantly reduce AMR by > 0.41 in both sexes and high economic status would reduce male AMR by 0.44, and female AMR by 0.70, in relation to countries without UHC, with political instability, and low economic status. Conclusions: Disparities in AM can be reduced after the achievement of UHC and economically productive activities for those adults affected by conflict and political unrest.

The aim of this study was to quantify methane (CH4) emissions from dairy cows during milking by maximum amplitude of eructation peaks and compare estimates with other metrics for CH4 emissions. Spot measurements of CH4 and carbon dioxide (CO2) emissions were recorded for at least 7 days of continuous sampling using an infrared gas analyser in a robotic milking station whilst cows were milked. Concentrations of CH4 and CO2 were measured at 1 second intervals. A total of 105,701 CH4 spot measurements were obtained from 2,206 dairy cows on 18 farms. Methane emissions per individual cow were quantified by maximum amplitude of eructation peaks, average area under eructation peaks (integral of eructation), average concentration during milking and ratio of CH4 to CO2 concentration. There was a high correlation (r = 0.71) between CH4 emissions quantified by maximum amplitude and integral of eructation peaks. The correlation between maximum amplitude and average CH4 concentration was low, and there was no correlation between maximum amplitude and ratio of CH4 to CO2. As both approaches identify and extract eructation peaks to quantify enteric CH4 emissions, the substantial association between maximum amplitude and eructation integral was expected.

The defining characteristic of Alzheimer's disease (AD) is the aberrant deposition of pathogenic proteins, particularly a massive build-up of amyloid-β peptides, specifically in the brain. Amy-loid-β aggregation is neurotoxic and ultimately results in dysfunction of the nervous system. The present investigation aims to predict potential amyloid-β fibrils disaggregating molecules from plant sources through molecular modeling techniques, this appears to be a very promising and appealing treatment philosophy. Here, 500 flavonoids from various plants were considered, ini-tially undergoing ADME studies to screen molecules that could cross the blood-brain barrier. Later, potential Amyloid-β-disaggregating molecules were identified by molecular docking and dynamics (MD) simulation studies. Five molecules, prenylmethoxy flavonol (-7.3 kcal×mol-1), isopentenyl flavonol (-7.3 kcal×mol-1), 7,3'-Dihydroxyflavone (-7.2 kcal×mol-1), 7-Hydroxy-5-methyl-4'-methoxyflavone (-7.2 kcal×mol-1), 8-hydroxy-7-methoxyflavone (-7 kcal×mol-1) showed higher binding affinity score against Alzheimer's Aβ (1-42) fibrils, these are very close to the standard drug (Donepezil) (-7.90 kcal×mol-1). Further, the MD simulation studies established the intermolecular interaction and stability of the five selected ligands-Amyloid-β oligomer protein complexes. These results suggest that the chosen five flavonoid molecules could be used as possible agents to disaggregate amyloid-β fibrils; however, more in vitro and in vivo investigations are required to verify the therapeutic effectiveness.

The aim of this study was to investigate the relationship between postprandial glycemic levels based on flash-monitoring and the production of intestinal hydrogen (H2) and methane (CH4) gases based on measurement of the amount of these gases in exhaled air. We studied 14 subjects with type 2 diabetes mellitus (T2DM) and 10 individuals without diabetes (control) with 3 food-load tests with simultaneous determination of gases in exhaled air and assessment of glucose levels. In 15.4% of patients with T2DM, there was a non-significant increase in exhaled H2. How-ever, all subjects in the control group had significant increase in exhaled H2. Moreover, the level of H2 in exhaled breathafter food load in patients with T2DM was lower than in normoglycemic subjects. Also, in normoglycemic subjects there was an inverse correlation between maximum glucose rise and maximum H2 in exhaled air after food load. At the same time in patients with T2DM the level of CH4 in exhaled air directly correlated with the parameters of postprandial glycemia in the test with lactulose. Confirmation of a causal relationship between decreased H2 production, increased intestinal CH4 production, and more severe postprandial glycemia may identify new therapeutic targets in the correction of postprandial glycemia in patients with T2DM.

This paper proposes a novel single-stage buck-boost three-Level neutral-point-clamped (NPC) inverter with two independent dc sources coupled for the grid-tied photovoltaic (PV) application, which can effectively solve the unbalanced operational conditions generally appeared between two coupled independent PV sources induced by the unequal irradiation and temperature distribution. The proposed control scheme can simultaneously guarantee the maximum power point (MPP) operation of both PV sources and maintain the output waveform quality. Compared to the traditional two-stage PV inverter, the proposed NPC inverter could reduce the PV array voltage requirement and dc-link capacitors’ voltage rating, meanwhile show the advantage in operational efficiency. MATLAB simulations and the captured experimental results are presented to show the performance of the proposed three-level inverter.

This study investigates the use of Au-doped Pd anodic electrocatalysts on ATO support for the conversion of methane to methanol. The study involves cyclic voltammetry, in-situ Raman spectra, polarization curves, and FTIR analysis to determine the optimal composition of gold and palladium for enhancing the conversion process. The results demonstrate the potential for utilizing methane as a feedstock for producing sustainable energy sources. Pd75Au25/ATO electrode exhibited the highest OCP value, and Pd50Au50/ATO had the highest methanol production value at a potential of 0.05 V. Therefore, it can be concluded that an optimal composition of gold and palladium exists to enhance the conversion of methane to methanol. The findings contribute to the development of efficient and sustainable energy sources, highlighting the importance of exploring alternative ways to produce methanol.

Shale gas and coalbed methane are energy sources that partly or even mainly consist of methane stored in an adsorbed state in the pores of the organic-rich rock and coal seams. In this study, the graphene nanoslit model is employed to model the nanometer slit pores in shale and coal. The Grand Canonical Monte Carlo (GCMC) and Molecular Dynamics (MD) modelling methods are used to investigate the mechanisms of adsorption and displacement of methane in the slit pore. It was found that the CVFF forcefield resulted in the largest adsorption amount, while the PCFF forcefield resulted in the least. The COMPASS and COMPASS II force fields led to similar results. As the width of the slit pore increases, the adsorption amount of gas molecules increases, and the number density profile of adsorbed methane molecules alters from a single adsorption layer to multi-adsorption layers. The minimum slit pore width at which methane molecules can penetrate the slit pore was found to be 0.7 nm. Moreover, it is demonstrated that by lowering the temperature, the adsorption rate of the methane increases since the adsorption is an exothermic process. Enhancing methane recovery was investigated by the injection of gases such as CO2 and N2 to displace the adsorbed methane. The comparison of adsorption isotherms of gas molecules provided the following order in terms of the amount of adsorption: CO2&gt;CH4&gt;N2.

One of the most important factors impacting quality of content in Wikipedia is presence of credible sources. By following references readers can verify facts or find more details about described topic. A Wikipedia article can be edited independently in any of over 300 languages, even by anonymous users, therefore information about the same topic may be inconsistent. This also applies to use of references in different language versions of a particular article, so the same statement can have different sources. In this paper we analyzed over 40 million articles from the 55 most developed language versions of Wikipedia to extract information about nearly 200 million references and find the most popular and reliable sources. We presented 10 models for the assessment of the popularity and reliability of the sources based on analysis of meta information about the references in Wikipedia articles, page views and authors of the articles. Using DBpedia and Wikidata we automatically identified the alignment of the sources to a specific domain. Additionally, we analyzed the changes of popularity and reliability in time and identified growth leaders in each considered months. The results can be used for quality improvements of the content in different languages versions of Wikipedia.

The mechanical pre-treatment constitutes an unavoidable pre-step prior to biofuels conversion. As the cost of this step is often underestimated, recently researchers have striven to identify and characterize the mechanical pre-treatment effects in terms of post-treatment physical characterization, derived improvement of enzymatic digestibility, and output yields. The status of existing mechanical pre-treatment techniques is reviewed by substrate’s typology for lignocellulose biomass, focusing on comminution techniques. Emphasis has been dedicated to the particle size achieved after treatment, crystallinity breakage and eventual inhibitory phenomena deriving from the application of particle size reduction, which are analysed and discussed.

Biogenic emissions affect the urban air quality as they are ozone and SOA precursors and should be taken into account when applying photochemical pollution models. The present study presents an estimation of the magnitude of Non-Methane Volatile Organic Compounds emissions (NMVOCs) emitted by vegetation over Greece. The methodology is based on computation performed with the aid of a Geographic Information System (GIS) and theoretical equations in order to develop an emission inventory on a 6x6 spatial resolution, in a temporal resolution of 1hr covering one year (2016). For this purpose, a variety of input data was used: improved satellite land-use data, land-use specific emission potentials, foliar biomass densities, temperature and solar radiation data. Hourly, daily and annual isoprene, monoterpenes and other volatile organic compounds (OVOCs) were estimated. In the area under study, the annual biogenic emissions were estimated up to 472 kt, consisting of 46.6% isoprene, 28% monoterpenes and 25.4% OVOCs. Results delineate an annual cycle with increasing values from March to April, while maximum emissions were observed from May to September, followed by a decrease from October to January.

Motivated by South Africa's need in the transition to a net-zero economy; this study 10 investigates the integration of renewable energy sources (RES) into oil refineries, considering 11 therein unique challenges and opportunities. The research focuses on optimizing RES allocation 12 using Particle Swarm Optimization (PSO), a data-driven approach that adapts to real-time 13 operational conditions. Traditional energy management systems often struggle with the inherent 14variability of RES, leading to suboptimal energy distribution and increased emissions. Therefore, 15 this study proposes a PSO-based renewable energy allocation strategy specifically designed for oil 16 refineries. It considers factors like the levelized cost of energy, geographical location, and available 17 technology. The methodology involves formulating the optimization problem, developing a PSO 18 model, and implementing it in a simulated oil refinery environment. The results demonstrate 19 significant convergence of the PSO algorithm, leading to an optimal configuration for integrating 20 RES and achieving cost reductions and sustainability goals. The optimization result of 4,457,527.00 21 Rand achieved by iterations is much better than the result of 4,829,638.88 Rand acquired using 22Linear Programming as the baseline model. The mean cost, indicating consistent performance, has 23 remained at its original value of 4,457,527.00 Rand, highlighting the convergence. Key findings 24 include the average distance measure decreasing from 4.2 to 3.4, indicating particle convergence; 25 swarm diameter decreasing from 4.7 to 3.8, showing swarm concentration on promising solutions; 26 average velocity decreasing from 7.8 to 4.25, demonstrating refined particle movement; and the 27 optimum cost function achieved at 4,457,527 Rand with zero standard deviation, highlighting 28 stability and optimal solution identification. This research offers a valuable solution for oil 29 refineries seeking to integrate RES effectively, contributing to South Africa's transition to a 30sustainable energy future.

Methane is a greenhouse gas and identified as a key driver of near-term climate change. Bottom-up approaches estimate annual methane loss from US natural gas production and transport at 6 Tg, but recent studies suggest this may be an underestimate. To investigate this possibility, an equipment-based emissions inventory, using EPA emission factors, was developed to calculate methane emissions from oil and gas operations in the Delaware Basin, USA. Emission factors and activity data were then updated using contemporary and region-specific measurement data. The original inventory estimated emissions at 315 Gg CH4 y-1 (gas production-normalized rate of 0.6% loss), while the updated inventory estimated emissions of 1,500 Gg CH4 y-1 (2.8% loss). The largest changes resulted from large fugitive emissions from oil production (+430 Gg CH4 y-1), updating maintenance activity emissions (+214 Gg CH4 y-1), considering flaring inefficiency (+174 Gg CH4 y-1), and the inclusion of associated gas venting (+136 Gg CH4 y-1). This study suggests that a systematic underestimate probably exists in current bottom-up inventories and identifies sources currently missing or may be incorrect. We also strongly recommend that emission factors should be validated through direct comparison against measurement campaigns that include long-tail distributions typical of oil and gas activities.

To estimate The potential inventory of natural gas hydrates in the Levant Basin we correlated the gas hydrate stability zone (GHSZ), modeled with locally estimated thermodynamic parameters, with seismic indicators of gas. Compilation of oceanographic measurements define the deep-water temperature and salinity to 13.8°C and 38.8‰ respectively, predicting the top GHSZ at a water depth of 1250±5 m. Assuming beneath the seafloor a hydrostatic pore-pressure, the water body salinity, and geothermal gradients ranging between 20 to 28.5°C/km, yields a useful first-order base-GHSZ approximation. Our model predicts that the entire northwestern half of the Levant Basin lies within the GHSZ, with a median thickness of ~150 m. High amplitude seismic reflectivity (HASR) imaged on an extensive 3D seismic dataset, consistently correlates with verified active seafloor gas seepage and is pervasively distributed across the deep-sea fan of the Nile within the Levant. Two main trends observed for the distribution of HASR are suggested to represent: (1) shallow gas and possibly hydrates, within buried channel-lobe systems 25 to 100 m beneath the seafloor; and (2) a regionally discontinuous bottom simulating reflection (BSR) broadly matching the modeled base GHSZ. We therefore estimate the potential methane hydrates reserve within the Levant Basin at ~4 Tcf.

The NP method was used to elucidate the contributions of vehicles and coal combustion to seasonal and long-term atmospheric PM-bound Pyr and 1-NP concentrations in Kanazawa, Kitakyushu, Shenyang, and Shanghai in the Western Pacific region from 1997 to 2021. Among the four cities, Kanazawa demonstrated the lowest Pyr concentration. The contribution of vehicles to Pyr before and after 2010 were 35% and 5%, respectively. The 1-NP concentration reduced by a factor of more than 1/10. These changes can be attributed to the emission control from vehicles. Kitakyushu revealed the second lowest Pyr and the lowest 1-NP concentrations. Coal combustion was found to be the main contributor to Pyr, while its contribution to 1-NP increased from 9% to 19%. The large contribution of coal combustion is attributed to iron manufactures. Shenyang demonstrated the highest atmospheric Pyr concentration with its largest seasonal change. Vehicles are the largest contributors to 1-NP. However, coal combustion, including winter coal heating, contributed 97% or more to Pyr and more than 14% to 1-NP. Shanghai revealed the second highest Pyr and 1-NP concentrations, but the former was substantially lower than in Shenyang. Coal combustion was the major contributor, but the contribution of vehicles to Pyr was larger before 2010 similar to Kanazawa.

The article discusses issues related to the optimization of the operation of medium voltage networks, focusing on the optimization of network division points and the selection of the optimal network configuration aimed at reducing power and energy losses. The article provides a critical review of selected scientific works from recent years on the issue of network configuration optimization. The developed solution uses non-deterministic network models and statistical and probabilistic approaches. Optimization studies were carried out using heuristic optimization methods and proprietary algorithms for forecasting the load and power generated from renewable energy sources. The solution proposed in the article has many application possibilities. It can be used to optimize the location of network division points (reducing economic costs related to the modernization of network infrastructure) as well as to optimize the reconfiguration process in order to reduce power losses while maintaining voltage criteria.

Metaverse has become an emerging trend for both academia and industry, and it seems to concern the next generation of the Internet. Although it is still in its grassroots, metaverse is estimated to bring disruption to people’s lives. One of the effects concerns the generation of new value oppor-tunities that don't exist in real life. These new types of value as well as their impact on people's lives must be explored. In this respect, this paper utilizes literature evidence to define the value types of metaverse, which are circulated with experts from the focus group on metaverse of the Interna-tional Telecommunications Union. Results uncover economic, public, and social values that metaverse generates, which can ensure its financial viability and the community's social sustaina-bility. The economic value sources come from both the industrial and the commercial sectors, while the public values concern citizen empowerment and government efficiency. The social values of metaverse concern employment growth, and the provision of immersive experiences in enter-tainment and education environments. Finally, this paper critically reviews their role for envi-ronmental, economic, and social sustainability. The literature review indicated that metaverse can on the one hand, enhance sustainability but on the other hand, it can cause environmental impact.

Abstract: The search for alternative protein sources to soy-bean meal (SBM) in animal feeding is a strategic objective to reduce production costs and contribute to a sustainable animal produc-tion. Spirulina, due to the high protein content, has emerged as a potential cost-effective, sus-tainable, viable and high nutritional value food resource for many animal species. Insect larvae (Tenebrio molitor and Hermetia illucens) are also considered potential alternatives to SBM, given their high edible percentage of almost 100%, as well as a protein value higher than that of vegetable proteins. Rapeseed meal and grain legumes, such as faba beans, peas, lupins and chickpea can also be used as locally producible protein ingredients. This study reviews the nutritional value of these potential alternatives to SBM in pig diets, effects on animal perfor-mance, digestion, immune system, physicochemical and sensorial characteristics of meat, in-cluding processed meat products of pork. Limits on their use in pig feeding are also reviewed to indicate gaps to be filled in future research on the supplementation level of these potential al-ternative protein sources into pig diets.

Quantifying methane emissions is essential for meeting near-term climate goals and typically done using methane concentrations measured downwind of the source. One major source of methane that is important to observe and promptly remediate is fugitive emissions from oil and gas productions sites but installing methane sensors at the thousands of sites within a production basin is expensive. In recent years, relatively inexpensive metal oxide sensors have been used to measure methane concentrations at production sites. Current methods used to calibrate metal oxide sensors have been shown to have significant shortcomings resulting in limited confidence in methane concentrations generated by these sensors. To address this, we investigate using machine learning (ML) to generate a model that converts metal oxide sensor output to methane mixing ratios. To generate test data, two metal oxide sensors, TGS2600 and TGS2611, were collocated with a trace methane analyzer downwind of controlled methane releases. Over the duration of the measurements, the trace gas analyzer’s average methane mixing ratio was 2.40 ppm with a maximum of 147.6 ppm. The average calculated methane mixing ratios for the TGS2600 and TGS2611 using the ML algorithm were 2.42 ppm and 2.40 ppm with maximum values of 105.9 ppm and 106.3 ppm, respectively. A comparison of histograms generated using the analyzer and metal oxide sensors mixing ratios show overlap coefficients of 0.95 and 0.94 for the TGS2600 and TGS2611, respectively. Overall, our results showed there was a good agreement between the ML derived metal oxide sensors’ mixing ratios and those generated using the more accurate trace gas analyzer. This suggests that the response of lower-cost sensors calibrated using ML could be used to generate mixing ratios with precision and accuracy comparable to higher price trace methane analyzers. This would improve confidence in low-cost sensors’ response, reduce the cost of sensor deploying, and allow for timely and accurate tracking of methane emissions.

As a major coal country, China faces the issue of significant gas emissions during the coal mining process. This study aims to improve the utilization efficiency of mine gas, reduce greenhouse gas emissions, and promote the low-carbon and green transformation of the coal industry. A 10kW gas regenerative thermal oxidation (RTO) experimental system was constructed. The effects of initial methane concentration, low-temperature flue gas proportion, and operating load on combustion temperature, methane oxidation rate, high-temperature flue gas energy, and system thermal efficiency were studied. The results show that when the combustion temperature is below 600°C, the CH4 combustion reaction cannot proceed effectively, and the system temperature continuously decreases and cannot be maintained stable. The experiment determines the stable operating methane concentration range of RTO. In this experimental system, the lower limit of the initial methane concentration is 0.28%, corresponding to an 86% methane oxidation rate. As the initial methane concentration decreases, the combustion temperature also decreases, and the methane oxidation rate follows suit. The higher the low-temperature flue gas proportion, the higher the combustion temperature, and the system thermal efficiency and output heat decrease with the increase of the low-temperature flue gas proportion. This experiment explores multiple factors affecting regenerative thermal oxidation, providing an basis for ensuring the safe and stable operation of the system and optimization. Improving the thermal insulation and heat exchange performance of the storage body can expand the lower limit of the initial methane concentration, thereby increasing the stability and thermal efficiency of the system.

The air in subterranean karst cavities is often depleted in methane (CH₄) relative to the atmosphere. Karst is considered a potential sink for the atmospheric greenhouse gas CH₄ because its subsurface drainage networks and solution-enlarged fractures facilitate atmospheric exchange. Karst landscapes cover about 14% of earth’s continental surface, but observations of CH₄ concentrations in cave air are limited to localized studies in Gibraltar, Spain, Indiana (USA), Vietnam, Australia, and by incomplete isotopic data. To test if karst is acting as a global CH₄ sink, we measured the CH₄ concentrations, δ¹³C_CH4, and δ²H_CH4 values of cave air from 33 caves in the USA and three caves in New Zealand. We also measured CO₂ concentrations, δ¹³C_CO2, and radon (Rn) concentrations to support CH₄ data interpretation by assessing cave air residence times and mixing processes. Among these caves, 35 exhibited subatmospheric CH₄ concentrations in at least one location compared to their local atmospheric backgrounds. CH₄ concentrations, δ¹³C_CH4, and δ²H_CH4 values suggest that microbial methanotrophy within caves is the primary CH₄ consumption mechanism. Only 5 locations from 3 caves showed elevated CH₄ concentrations compared to the atmospheric background and could be ascribed to local CH₄ sources from sewage and outgassing swamp water. Several associated δ¹³C_CH4 and δ²H_CH4 values point to carbonate reduction and acetate fermentation as biochemical pathways of limited methanogenesis in karst environments and suggest that these pathways occur in the environment over large spatial scales. Our data show that karst environments function as a global CH₄ sink.

Earthquakes are one of the most catastrophic natural phenomena. After an earthquake, earthquake reconnaissance enables effective recovery by collecting building damage data and other impacts. This paper aims to identify state-of-the-art data sources for building damage assessment and provide guidance for more efficient data collection. We have reviewed 38 articles that indicate the sources used by different authors to collect data related to damage and post-disaster recovery progress after earthquakes between 2014 and 2021. The current data collection methods have been grouped into seven categories: fieldwork or ground surveys, omnidirectional imagery (OD), terrestrial laser scanning (TLS), remote sensing (RS), crowdsourcing platforms, social media (SM) and closed-circuit television videos (CCTV). The selection of a particular data source or collection technique for earthquake reconnaissance includes different criteria depending on what questions are to be answered by this data. We conclude that modern reconnaissance missions can not rely on a single data source and that different data sources should complement each other, validate collected data, or systematically quantify the damage. The recent increase in the number of crowdsourcing and SM platforms used to source earthquake reconnaissance data demonstrates that this is likely to become an increasingly important source of data.

Gravitational waves have been detected in the past few years from several transient events such as merging stellar mass black holes, binary neutron stars, etc. These waves have frequencies in a band ranging from a few hundred hertz to around a kilohertz to which LIGO type instruments are sensitive. LISA would be sensitive to much lower range of frequencies from SMBH mergers. Apart from these cataclysmic burst events, there are innumerable sources of radiation which are continuously emitting gravitational waves of all frequencies. These include a whole mass range of compact binary and isolated compact objects as well as close planetary stellar entities. In this work, quantitative estimates are made of the gravitational wave background produced in typical frequency ranges from such sources emitting over a Hubble time and the fluctuations in the h values measured in the usual devices. Also estimates are made of the high frequency thermal background gravitational radiation from hot stellar interiors and newly formed compact objects.

Distributed Energy Resources might have a severe influence on Power Line Communications, as they can generate interfering signals and high frequency emissions or supraharmonics that may cause loss of metering and control data. In this paper, the influence of various energy resources on Narrowband Power Line Communications is described and analyzed through several test measurements performed in a real microgrid. Accordingly, the paper describes the effects on smart metering communications through MAC layer analysis. Results show that the commutation frequency of inverters and the presence of battery chargers are remarkable sources of disturbance in low voltage distribution networks. In this sense, the results presented can contribute to efforts towards standardization and normative of emissions at higher frequencies higher, such as CENELEC EN 50160 and IEC/TS 62749.

The oxidative coupling of methane (OCM) to produce ethane and ethylene (C2 compounds) as platform chemicals involves complex chemistry with reactions both in the gas phase and on the catalyst surface, resulting in a distribution of products at the expense of C2 selectivity. This work uses experimental data from a variety of mixed metal oxides on supports at different reaction conditions (temperature, contact time, and reactant flow rates) to train a random forest regressor that predicts methane conversion and C2 selectivity (key performance indicators (KPIs)), and deploys it to locate optimal conditions that maximize C2 yield for a catalyst. Investigating the regressor interpretability via feature importance reveals that the choice of metals and support are crucial to C2 selectivity predictions, while the predictions of methane conversion are driven by the reaction conditions. The machine learning (ML) regressor is used as a surrogate to develop performance curves for each of the catalysts via a multi-objective optimization routine that seeks to maximize the KPIs in the decision space of reaction conditions, is seen to locate optimal conditions at which the maximum C2 yields for catalysts are predicted to be 15%, higher on average. Analyzing the catalysts in the space of their performance curves with respect to a popular OCM catalyst, Mn-Na2WO4/SiO2, reveals distinct patterns based on intrinsic properties of metals and supports. Further, the decision space with catalyst descriptors and reaction conditions is optimized for high C2 yields using the ML surrogate, in a static multi-objective optimization routine, and an adaptive Bayesian routine, where the latter was found to have a wider field focus in proposing catalyst formulations and conditions. Transition metal oxides on a variety of supports were proposed but not their lanthanide oxide counterparts.

Methane (CH4), produced endogenously in animals and plants, has recently been suggested to play a role in cellular physiology, potentially influencing the signaling pathways and regulatory mechanisms involved in nitrosative and oxidative stress responses. In addition, it has been proposed that supplementation of CH4 to organisms may be beneficial for the treatment of several diseases, including ischemia, reperfusion injury, and inflammation. However, it is still unclear if and how CH4 is produced in mammalian cells without the help of microorganisms, and how CH4 might be involved in physiological processes in humans. In this study, we provide first proof of the principle that CH4 is formed non-microbially in the human body by applying isotopically labeled methylated sulfur compounds, such as dimethyl sulfoxide (DMSO) and methionine, as carbon precursors to confirm cellular CH4 formation. A volunteer applied isotopically labeled (2H and 13C) DMSO on the skin, orally, and to blood samples. Monitoring of stable isotope values of CH4 convincingly showed the conversion of the methyl groups, as isotopically labeled CH4 was formed during all experiments. Based on these results, we consider several hypotheses about endogenously formed CH4 in humans, including physiological aspects and stress responses involving reactive oxygen species (ROS). While further and broader validation studies are needed, the results may unambiguously serve as a proof of concept for the endoge-nous formation of CH4 in humans by a radical-driven process. Furthermore, these results might encourage follow up studies to decipher the potential physiological role of CH4 and its bioactiv-ity in humans in more detail. Of particular importance is the potential to monitor CH4 as an ox-idative stress biomarker if the observed large variability of CH4 in breath air is an indicator for physiological stress responses and immune reactions. Finally, the potential role of DMSO as a radical scavenger to counteract oxidative stress caused by ROS might be considered in the health sciences. DMSO has already been investigated for many years, but its potential positive role for medical use remained highly uncertain.

Recent studies have emphasized the influence of resettlement factors on the mental health of refugees resettling in developed countries. However, little research has addressed gender differences in the nature and influence of resettlement stressors and sources of resilience. We address this gap in knowledge by investigating how gender moderates and mediates the influence of several sources of distress and resilience among 259 Afghan refugees residing in northern California. Gender moderated the effects of four factors on levels of distress. Intimate and extended family ties have little correlation with men’s distress levels, but are strongly associated with lower distress for women. English ability is positively associated with lower distress for women, but not men. In terms of gender ideology, traditionally oriented women and egalitarian men have lower levels of distress. And experiencing greater dissonant acculturation increases distress for men, but not women. The influence of gender interaction terms is substantial and patterns may reflect difficulty adapting to a different gender order. Future studies of similar populations should investigate gender differences in sources of distress and resilience, and efforts to assist new arrivals might inform them of changes in gender roles they may experience, and facilitate opportunities to renegotiate gender roles.

Reducing meat consumption is better for the environment. Unfortunately, commercial plant-based meat substitutes are often more expensive than meat and thus have not seen widespread adoption. This paper analyzes commercially-available spirulina, soy, pea, and brown rice protein isolates characteristics to provide data for non-meat protein cost reductions. Thermal and rheological properties, viscosity, density, and particle size distribution are analyzed for further study on alternative protein-based food processing. Differential scanning calorimetry analysis produced dry amorphous-shaped curves and paste curves with a more distinct endothermic peak. Extracted linear temperature ranges for processing in food production for spirulina was 70-90ºC; soy protein was 87-116ºC; pea protein was 67-77ºC; and brown rice protein was 87-97ºC. Viscosity analysis determined each protein material was shear-thinning and that viscosity increased with decreased water concentration, with rice being an exception to the latter trend. The obtained viscosity range for spirulina was 15,100-78,000cP; soy protein was 3,200-80,000cP; pea protein was 1,400-32,700cP; and brown rice protein was 600-3,500cP. The results indicate that extrusion is a viable method for further processing of the protein isolates as this technique has a large temperature operating range and variable screw speed. Data provided here can be used to make single or multi-component protein substitutes.

This paper discusses the mathematical modelling of exothermic explosions in a slab. This model is based on a nonlinear equation containing a nonlinear term related to Arrhenius, bimolecular, and sensitised laws of reaction kinetics. The absolute temperature can be obtained by solving the nonlinear equation using Akbari-Ganji’s method. The influence of the parameters Frank-Kamenetskii, activation energy and numerical exponent on temperature is discussed. The analytical results are compared with previous available analytical and numerical results ( Matlab). A satisfactory agreement is noted.

Wi-Fi fingerprinting positioning systems have been deployed for a long time in location-based services for indoor environments. Combining mobile crowdsensing and Wi-Fi fingerprinting systems could reduce the high cost for collecting the necessary data enabling the deployment of the resulting system for outdoor positioning in areas with dense Wi-Fi coverage. In this paper, we present the results attained in the designing and evaluation of an urban fingerprinting positioning system based on crowdsensed Wi-Fi measurements. We first asses the quality of the collected measurements, highlighting the influence of received signal strength on data collection. We then, evaluate the proposed system by comparing the influence of the crowdsensed fingerprints on the overall positioning accuracy for different scenarios. The evaluation helps gain valuable insight into the design and deployment of urban Wi-Fi positioning systems while also allowing the proposed system to match GPS-like accuracy in similar conditions.

In this paper, four lithological parameters, i.e. thermal conductivity, particle size, porosity and saturation, are investigated by combining experimental observations with numerical simulations to study the influence laws and mechanisms of action on the combustion process of methane hydrate sediments. The variation of combustion characteristics parameters such as flame height, effective combustion ratio and dimensionless discharge water mass with the lithological parameters are studied. In addition, the combustion mechanism of lithologic parameters on methane hydrate deposits is revealed. Combining the experimental results and simulation calculations, to optimize the combustion of methane hydrate sediments, it is recommended to use methane hydrate sediment samples with high saturation and low thermal conductivity, while the oxidant concentration and porosity of methane hydrate sediment samples should be increased.

Researchers have been exploring seaweed to reduce methane (CH4) emissions from livestock. This study aimed to investigate the potential of a red alga, Bonnemaisonia hamifera, as an alternative to mitigate CH4 emissions. B. hamifera, harvested from the West coast of Sweden, was used in an in vitro experiment using a fully automated gas production system. The experiment was a ran-domized complete block design consisting of a 48-h incubation that included a control (grass si-lage) and B. hamifera inclusions at 2.5%, 5.0% and 7.5% of grass silage OM mixed with buffered rumen fluid. Predicted in vivo CH4 production and total gas production were estimated by ap-plying a set of models to the gas production data and in vitro fermentation characteristics were evaluated. The results demonstrated that the inclusion of B. hamifera reduced (P = 0.01) predicted in vivo CH4 and total gas production, and total gas production linearly decreased (P = 0.03) with higher inclusion of B. hamifera. The molar proportion of propionate increased (P = 0.03) while isovalerate decreased (P = 0.04) with inclusion of B. hamifera. There was a tendency for increased (0.06 ≤ P ≤ 0.10) total volatile fatty acid production, as well as lower proportions of butyrate, isobutyrate, and 2-methylbutyrate. Chemical analyses revealed that B. hamifera had moderate concentrations of polyphenols. The iodine content was low and there was no detectable bromo-form, suggesting quality advantages over Asparagopsis taxiformis. Additionally, B. hamifera exhib-ited antioxidant activity comparable to the positive control Resveratrol. The findings of this study indicated that B. hamifera harvested from temperate waters in Sweden possesses capacity to mitigate CH4 in vitro.

The direct methane to methanol (MTM) oxidation is a grand challenge in catalysis, with profound economical implications for the modern chemical industry. Bioinspired metal-organic frameworks (MOFs) with active iron and copper sites have been emerging very recently as innovative catalytic platforms to accomplish the MTM conversion under mild conditions. This review discusses the current state of the art regarding the application of MOFs with iron and copper catalytic centers to perform the MTM reaction, with a focus on the diverse spectroscopic techniques used to unveil the electronic and structural properties of the MOF catalysts at a microscopic level. We explore the synthetic strategies employed to incorporate iron and copper sites into different MOF topologies, the efficiency and selectivity of the iron- and copper-bearing MOF catalysts, and the ensuing MTM reaction mechanisms proposed on the basis of spectroscopic characterization supported by theory. In particular, we evidence how the combination of complementary spectroscopic tools probing different regions of the electromagnetic spectrum is particularly useful to reach a satisfactory understanding of the key reaction pathways and intermediates. Finally, we provide a critical perspective on future directions to advance the use of MOFs to accomplish the MTM reaction.

Methane (CH4) emissions from agricultural sources make a significant contribution to the total anthropogenic greenhouse gas emissions that contribute to climate change. According to the International Panel on Climate Change (IPCC) guidelines for calculating greenhouse gas emissions, agriculture is responsible for approximately 10% of total CH4 emissions from anthropogenic sources. CH4 is mainly emitted from livestock farming, especially from cattle production during enteric fermentation and from manure. The article describes the results of multivariate statistical analyzes carried out on data collected in 1961–2020 based on the data for 30 countries with the largest cattle population. The trends of temporal changes in cattle population were evaluated and groups of countries with similar patterns in the study period were distinguished. Variables which are correlated with changes in the number of cattle were indicated. Forecasts of cattle population and CH4 emission related to cattle for the coming years are presented.

The conversion of methane into chemicals is of interest to achieve a decarbonized future. Fuel cells are electrochemical devices commonly used to obtain electrical energy, but can be utilized either for chemicals production or both energy and chemicals cogeneration. In this work, the partial oxidation of methane in fuel cells for electricity generation and valuable chemicals production at the same time is reviewed. For this purpose, different types of methane-fed fuel cells, both low temperature fuel cells, such as PEMFCs and AAEMFCs, and high temperature fuel cells, such as SOFCs, have been used. Also if few works have been devoted to this topic, the promising results drive the development of fuel cells using methane as the source for the cogeneration of power and valuable chemicals.

Moisture and thermal are the key factors for influencing methane desorption during CBM exploitation. Using high pressure water injection technology into coalbed, new fractures and pathways are formed to methane transport. It is existed a phenomenon of water inhibiting gas flow. This study is focused on various water pressures impacted on gas adsorbed coal samples, then the desorption capacity could be revealed under different conditions. And the results are shown that methane desorption capacity was decreased with water pressure increased at room temperature and the downtrend would be steady until water pressure was large enough. Heating could promote gas desorption capacity effectively, with the increasing of water injection pressures, the promotion of thermal on desorption became more obvious. These results are expected to provide a clearer understanding of theoretical efficiency of heat water or steam injection into coalbed, they can provide some theoretical and experimental guidance on CBM production and methane control.

Leishmaniasis is considered one of the different neglected tropical diseases by the World Health Organization. Over the past few decades to tackle leishmaniasis, effective and novel drugs have progressed. But few are expensive some other medication shows poor effects and few drugs with long treatment lead to cause resistance. But it is very important to start a better medication against leishmania so researchers came to the front of the utilization of natural products which are considered a better option. Finding active compounds in medicinal plants is another alternative to currently accessible medications. Materials and methods: This study examined and reported the far more potential natural products used to treat disease caused by Leishmania spp. Leishmaniasis, plant metabolites, in vivo, in vitro, and treatment against leishmaniasis have been used as search terms in the Google Scholar, PubMed, and Science Direct databases, and only papers published between 2015 and 2021 have been chosen for further analysis. Results: The use of novel natural compounds with leishmanicidal action as well as the leishmanicidal activity of natural compounds against promastigote, axenic, and intracellular amastigote forms were included in roughly 20 research papers that were reviewed.Conclusion: Due to their capacity to selectively target parasites without harming host cell viability, herbal plants are a possible source of new anti-leishmanial medication. Future leishmaniasis treatments will draw on the isolated compounds as a source, completing those already offered in clinics.

Classical religious texts remain an essential part of human culture due to their undiminished influence on the advancement of civilization. Although their entirely divine origin is questioned repeatedly, explicit or implicit quoting and adherence to their basic guidelines are fundamental in modern society. In this respect, these documents’ inner structure and linguistic style appear to be pivotal. This paper considers the topic from the standpoint of small textual patterns classified using deep learning methods, traditionally applied to analyze short textual material like tweets. We divide the considered documents into small sequential chunks imitating tweets and categorizing them, classifying an entire text. The proposed method demonstrates that the religious text collections correspond to stable ”Twitter”-like structures that adequately reflect stylistic properties. So, concise word combinations seem to be an inborn textual attribute that adequately outlines the proposed multi-source authorship. This approach differs from traditional methods of analyzing classical religious documents, which are based on the consideration and interpretation of relatively long templates. The case study consists of three famous collections of Mosaic authorship in the Old Testament (Hebrew), Pauline authorship in the New Testament (Greek), and Al-Ghazali authorship (Arabic). The obtained results go well with most previously expressed evaluations and complement them with new implications, particularly in the authorship of two famous manuscripts attributed to Al-Ghazali.

Microplastics (MPs) are small pieces of plastics. They are ubiquitous in the environment and can enter the freshwater environment from surface run-off and wastewater effluent (treated and untreated), industrial effluent, degraded plastic waste, and atmospheric deposition. They are not usually destroyed but convert into one phase to another. They are a source of air pollution, occurring in dust and airborne fibrous particles. Mostly MPs are non-biodegradable while some MPs are biodegradable, which can be decomposed in the presence of ultraviolet (UV) light or by the action of microorganisms. Popular methods: chemical, spectroscopic, and thermo-analytical are available for the determination of the chemical composition and size of plastic particles. This chapter discusses the uses, health hazards, sources, and transport of MPs particles.

Background/Objective: Adequate serum vitamin D levels are essential for overall health, particularly in preventing oropharyngeal infections. This study aims to explore the relationship between serum vitamin D (25(OH)D3) levels and the prevalence of oropharyngeal diseases—specifically rhinosinusitis, otitis media, and nasopharyngitis—in patients at a private specialist medical clinic. Materials and Methods: The study involved 311 patients with an average age of 15.96±15.06 years. Statistical analyses, including Student's t-test and chi-square test, were conducted to evaluate the significance of the findings. Results: Nasopharyngitis was highly prevalent, affecting 83.27% of participants, with higher recurrence rates in those with lower vitamin D levels (p=0.001). Otitis media was present in 53.37% of cases, while rhinosinusitis was less common and more frequently associated with higher vitamin D levels. Patients with behavioral disorders had significantly higher mean vitamin D levels (34.82 ng/mL ±11.85) compared to those without (28.49 ng/mL ±14.37) (p=0.001). Conclusion: Lower serum vitamin D levels are associated with an increased incidence of oropharyngeal diseases. This study highlights the importance of maintaining optimal vitamin D levels for pediatric health and suggests that higher vitamin D levels may reduce the risk of oropharyngeal infections.

Natural polysaccharides, which are described in this study, are some of the most extensively used biopolymers in food, pharmaceutical and medical applications, because they are renewable and have a high level of biocompatibility and biodegradability. The fundamental understanding required to properly exploit polysaccharides potential in the biocomposite, nanoconjugate, and pharmaceutical industries is depended on detailed research of these molecules. Polysaccharides are preferred over other polymers because of their biocompatibility, bioactivity, homogeneity, and bioadhesive. Natural polysaccharides have also been discovered to have excellent rheological and biomucoadhesive properties, which may be used to design and create a variety of useful and cost-effective drug delivery systems. Polysaccharide-based composites derived from natural sources have been widely exploited due to their multifunctional properties, particularly in drug delivery systems and biomedical applications. These materials have achieved global attention and are in great demand because to their biochemical properties, which mimic both human and animal cells. Although synthetic polymers account for a substantial amount of organic chemistry, natural polymers play a vital role in a range of industries, including biomedical, pharmaceutical, and construction. As a consequence, the current study will provide information on natural polymers, their biological uses, food and pharmaceutical applications.Keywords: Polymers Biopolymers, Excipient, Natural source, Food and Pharmaceutical applications.

This paper identifies preschool teachers' sources of stress, the times they experience high stress, and their ways of coping with stress levels. The study was conducted using a phenomenological design, one of the qualitative research models. The data were collected through semi-structured interviews with 36 preschool teachers working with children aged 0-6 in state and private schools. As a result of the content analysis, stressors were identified primarily at both interpersonal (positive, and effective interactions), and organizational levels (school management, and leadership style). It was also found that intense stress was experienced when children were difficult to control, such as during sleeping, eating, and cleaning. Finally, these results confirmed that the teachers used active/active behavioral, and passive/avoidant coping strategies. However, it was understood that preschool teachers perceived stress negatively, and did not see stress as a personal development situation. These results are discussed in terms of their ramifications for preschool education.

Air pollution has been a major environmental issue worldwide from the last few decades. It is a man-made issue that has a serious harmful impact on the environment and the health of humans. There are different sources of emission, but industrial processes and motor vehicles contribute to a chief part of air pollution. It has acute as well as chronic effects on the health of humans and affects different organs. It is thought the main environmental risk factor in the incidence and progression of several diseases such as lung cancer, asthma, Alzheimer's and Parkinson's diseases. Long-term exposure to air pollution has different toxicological impacts on humans such as respiratory and cardiovascular diseases, neuropsychiatric complications, eye irritation and skin diseases. As per the study by the World Health Organization (WHO), nitrogen oxides (NOx), carbon monoxide (CO), ozone (O₃), sulfur dioxide (SO₂), volatile organic compounds (VOCs) and heavy metals are the major air contaminants. These pollutants are different in their properties, composition and time of disintegration. The aim of this study is to review the different sources, types, impacts, challenges and mitigation of air pollution in detail.

In this work, the Pumped Storage Unit (PSU) is proposed to be integrated with wind-thermal generation system owned by a company whose aim is to maximize its profit through optimal self-scheduling of its units by finding the best bidding strategy in day-ahead energy market. The mathematical formulation of the scenario based unit-commitment and coordinated trading problem is formulated as a stochastic mixed integer linear program. The formulation takes into account several uncertain parameters; such as the wind power generation, energy market prices, and imbalances up/down prices. The expected total profit obtained from energy trading with and without coordinating pumped storage system (PSS) with thermal-wind generation system were compared, and a significant improvement in profit resulted from coordination was observed. Furthermore, coordination between PSS and wind-thermal generation improve the conditional value at risk (CVaR) which monitors the biding risk level.

Cities are important sources of anthropogenic methane emissions. Municipal governments can play a role in reducing those emissions to support climate change mitigation, but they need information on the rate of emissions to context mitigation actions and track progress. Here, we examine the application of satellite data from the TROPOspheric Monitoring Instrument (TROPOMI) to estimate city-level methane emissions rates in a case study of the City of Calgary, Alberta, Canada. While satellites are touted as a global methane monitoring system, we found limited observational coverage over Calgary that precluded the reliability of measurement-based models to track the annual emissions. In this work, we integrated valid observations over three years (2020-22) and used mass balance modeling to derive a long-term averaged emission estimate. The column-averaged dry-air mole fraction (XCH4) enhancement over Calgary was small, 4.7 ppb, but within the city boundary, we identified local hot spots in the vicinity of known sources (wastewater treatment facility and landfills). The city-scale emissions estimate from mass balance was 215.4 ± 132.8 t/d CH4. This estimate is approximately four- and six-times larger than estimates from Canada's gridded national inventory report of anthropogenic CH4 emissions and the Emissions Database for Global Atmospheric Research (EDGAR v8.0), respectively. Valid observations are more common in warmer months and occur during a narrow daily overpass timeslot over Calgary – these effects may bias the emissions estimate. Overall, the findings from this case study highlight the challenge of deriving routine (sub-annual to annual) satellite-based estimates of city-scale methane emissions in similar geographic settings and suggest that more granular emissions inventories are needed to improve methane reporting.

: Sulfate presence is of great importance for anaerobic digestion as its addition can control the anaerobic microbial community. In this study, the effect of sulfuric acid addition on the perfor-mance of an UASB reactor fed with hydrolyzed starch was investigated. TOC, Fe and SO4-2 re-moval as well as the methane production were monitored under various COD/ SO4-2 ratios, HRTs and OLRs. When HRT was 16 hours and OLR equal to 2 g COD/LUASB-d the methane production was 0.24 L CH4/LUASB-day. After the sulfuric acid addition, TOC removal reached 95%. At HRT, OLR, and COD/ SO4-2 ratio equal to 16 hours, 2 g COD/ LUASB-d and 3.72 respectively, the methane production was 0.267 L CH4/LUASB-d. When the OLR was increased to 5.94 g COD/LUASB-d and COD/SO4-2 ratio was equal to 12.5, the methane production was 3 times higher (0.84 L CH4/LUASB-d) with a methane content in the produced biogas greater than 70%. 16s rRNA gene analysis demonstrated that after the sulfate addition, SRB were enriched and methane was mainly produced by Methanosaeta sp. This study indicates that appropriate sulfate concentrations in the feed in combination with the presence of iron in the UASB reactor lead to enhanced me-thane yields.

The spiral tube heat exchange is widely used in large-scale liquefaction process. However, the research on the friction pressure drop of the two-phase flow in the spiral tube is limited, especially for the offshore sloshing condition. In this paper, an experimental system is designed and built, and the effects of sloshing form (roll, pitch, heave), sloshing period (5-15s), mass flux (200-800 kg/(m2·s)), vapor quality (0.3-0.9) and operating pressure (2-4 MPa) on friction pressure drop of methane/ethane (C1/C2) mixture in spiral tube are studied. The result shows that the growth rate of time-averaged friction pressure drop during condensation under sloshing condition is less than 0, which indicates that sloshing will lead to drag reduction. And under the three sloshing parameters, the growth rate of time-averaged friction pressure drop of C1/C2 is reduced by-5.99%%, 5.97% and -6.70% respectively.

Exploration practices have proven that over mature shale gas exhibits a feature of carbon isotope reversal. The geochemical statistics indicate that the wetness (C2-C5/C1-C5) of shale gas with carbon isotope reversal is less than 1.8%. In addition, the magnitude of carbon isotope reversal (δ13C1- δ13C2) for the over mature shale gas presents a parabolic variation with decreasing wetness. δ13C1-δ13C2 increases with decreasing wetness within a wetness range of 0.9% ~1.8% and then decreases with decreasing wetness at wetness < 0.9%. The CH4 cracking experiment demonstrates that CH4 polymerization occurring in the early stage of CH4 cracking is an important factor involved in isotope reversal of over mature shale gas. Moreover, δ13C1- δ13C2 decreases with an increase in experimental temperature prior to CH4 substantial cracking. The values of δ13C1 and δ13C2 tend to equalize during CH4 substantial cracking. The δ13C1-δ13C2 of mud gas present at different depths during shale gas drilling in Sichuan Basin increases initially, then decreases with further increase in the depth and finally tends to zero, with only a trace hydrocarbon gas being detectable. Statistical data suggests that the shale gas production in Sichuan Basin decreases with the decreasing δ13C1-δ13C2 value and wetness. Thus, δ13C1-δ13C2 and wetness could potentially serve as useful criteria to screen CH4 cracking degree and to determine the largest depth of natural gas exploration. Great care should be taken during shale gas exploration in deeper layers, with wetness and δ13C1-δ13C2 less than 0.2% and 1%, respectively, since very low wetness (<0.2%) and δ13C1-δ13C2 (<1%) might be indicative of CH4 substantial cracking in a geological setting.

This study numerically analyzed the effect of composition and temperature and oxygen concentration changes on the selfignition characteristics of n-heptane/methane blended fuels in order to cope with development of alternative fuels and international environmental regulations. CHEMKIN-PRO is used as the analysis program and the LLNL model is used as the reaction model. The numerical results revealed that on autoignition and ignition delay time were sensitive to changes in fuel composition and oxygen concentration. As the methane ratio increases, OH radicals causing ignition are delayed in generation and the concentration is lowered, thus longer the ignition timing. The oxygen concentration in the mixed fuels are changed to simulate the exhaust gas recirculation and a numerical analysis in then performed. As the oxygen concentration decreases, the ignition delay time longer because the nitrogen gas acts as a thermal load in the combustion chamber.

This work presents a methodology for the generation and classification of phase resolved partial discharges (PRPD) patterns based on the use of a printed UHF monopole antenna and signal con-ditioning circuit to reduce hardware requirements. For this purpose, envelope detection technique was applied. In addition, test objects such as a hydrogenerator bar, dielectric disks with internal cavities in an oil cell, potential transformer, and tip-tip electrodes immersed in oil were used to generate partial discharge (PD) signals. To detect and classify partial discharges, the standard IEC 60270 (2000) method was used as reference. After acquisition of conditioned UHF signals, digital signal filtering threshold technique was used, and peaks of partial discharges envelopes pulses were extracted. Feature selection techniques were used to classify the discharges and choose the best features to train machine learning algorithms, such as multilayer perceptron, support vector ma-chine and decision tree. Accuracies greater than 84% were met, revealing the classification potential of the methodology proposed in this work.

The aim of this study was to examine the post-injury psychological impact looking for to avoid sources of health issues. We have analyzed differences in the stress, anxiety and depression levels between male and female football players who have suffered at least one injury during the last season played respect to similar players who have not been injured. A descriptive cross-sectional design was used. The participants were 187 football players and data on the player’s injuries were collected. A Self-reported Questionnaire collected number, type and severity of injuries sustained during the previous sports season (twelve months), and also the player’s current situation being injured or not injured. To evaluate the psychological variables, the DASS-21 questionnaire was used. Results indicated that the male injured players presented anxiety levels higher than those who were non-injured. When we observe the female players’ data, the stress levels of the non-injured ones are higher than those of the injured players. Regarding the non-injured athletes, results showed that the female non-injured players presented values in anxiety higher than those corresponding to the non-injured male players. Thus, sport injury affects mental health issues such as anxiety and stress, and in a different way regarding gender.

Corn is both the most important and nitrogen (N)-fertilized crop, but N losses from agricultural systems impact the environment. There is a lack of long-term data comparing effects of tilled systems receiving organic N fertilizer (TONF; e.g., manure) versus inorganic N fertilizer (TINF; e.g., urea) on N balance and losses. A long-term study assessing effects of TONF and TINF and comparing them to no till (NT) and strip till (ST) systems receiving inorganic nitrogen fertilizer (INF) was conducted with an irrigated continuous corn (CC) system with minimal erosion in Fort Collins, Colorado, USA. An N balance found a system nitrogen use efficiency (NUE_Sys) for TONF (manure) of 86.3%, which was higher than the NUE_Sys of TINF (enhanced efficiency fertilizer, EEF) of 60.2%. TONF (manure) contributed to higher HGY (2 of 11 yr.), higher C sequestration (P<0.05), and higher soil organic N content (P<0.05) than TINF. Soil phosphorus (P) and nitrate were higher with TONF than TINF (P<0.05). Both TONF and TINF had higher HGY and HGY N content (HGYN) than NT and ST (P<0.05). From 2012 to 2023, the HGY of the TONF did not decrease, while the HGY of TINF decreased with time (P<0.05). TONF is a best management practice to increase yields and N and C sequestration while reducing N losses compared to TINF and achieving higher yields than NT and ST. A combination of manure (30% of N input) with EFF (70% of N input) contributed to a synergistic effect that increased agronomic productivity.

The 2020-2025 Dietary Guidelines for Americans recommends limiting intakes of saturated fat and added sugars (SF/AS) to 88% of the representative sample of U.S. adults. The top sources of SF were cheese, pizza, ice cream, and eggs. The leading sources of AS were soft drinks, tea, fruit drinks, and cakes and pies. This analysis reflects a parsimonious approach to reliably identify foods and beverages that contribute to SF/AS intakes in U.S. adults.

The aims of study was to evaluate the effects of rates, sources and timing of nitrogen application under cover of transgenic corn yield cultivated in Amazon Biome. The experiments were conducted in Parauapebas city, State of Pará, Brazil, in two years (2016/2017 and 2017/2018). The experimental design was randomized blocks, in a 5x2x2 factorial scheme, consisting of five rates of N (0; 45; 90; 135; and 180 kg ha-1), two nitrogen sources (urea and ammonium sulfate) and two application times of N (phenological stages V4 and V8), with four replications. The factor N rates promoted adjustment of linear equation (leaf area index, mass of thousand grains, and yield) and quadratic equation (dry mass of leaf index). Nitrogen fertilization promoted significant increases in mass of thousand grains and yield, obtaining the best results with 180 kg ha-1 of N applied at V4 phenological stage. Based on results obtained in two years of corn cultivated under conditions of Amazon Biome, the application of N at V4 phenological stage at rates of 121 to 131.39 kg ha-1 of N showed the best results for vegetative growth, while 180 kg ha-1 of N, regardless of source used, urea or ammonium sulfate, promoted greater grain weight and greater yield.

Methane (CH4) has attracted attention as not only synthetic natural gas, but also one of the hy-drogen carriers in terms of energy density. On the other hand, there exist bacterial ecosystems in nature that can decompose organic compounds to produce CH4 and CO2. In this study, Clostridi-um cellulovorans was first cultivated with pig manure (PM) as an unused biomass. Regarding the measurement of organic acids by high-performance liquid chromatography (HPLC), acetate and butyrate were increased in the C. cellulovorans medium containing 0.5% PM, while formate and lactate were decreased in it. Next, in comparison with carbon sources such as glucose, cellobiose, and acetate, cocultivation of C. cellulovorans and Methanosarcina mazei or microbial flora of me-thane production (MFMP) was performed in the C. cellulovorans medium. These results revealed that 0.5% acetate as the sole carbon source produced CH4 only by cocultivating C. cellulovorans and MFMP. Furthermore, MFMP was only cultivated with 1% acetate or 1% methane as a carbon source after precultivated with 0.5% glucose medium for 12 h. As a result, methane productivity of MFMP with 1% methanol medium was approximately eight times higher than that with 1% acetate medium. Finally, next-generation sequencing (NGS) analysis of MFMP after cultivation with 1% acetate or 1% methane was carried out. Interestingly, Methanofollis (0.211%) belonging to H2/CO2 -using methanogens (CO2 reduction pathway) was dominant in the 1% acetate medium for 72 h cultivation, whereas Methanosarcina siciliae (1.178%), M. barkeri (0.571%), and Methano-follis (0.490%) were major species in 1% methanol medium for 72 h cultivation. Since Methano-sarcina spp. are belonging to acetoclasts (acetoclastic pathway), methanol could promote to grow Methanosarcina spp. rather than acetate. Therefore, it seemed Methanosarcina spp. may play a key methanogenesis in MFMP. Thus, these results will provide important information for low cost biomethane production.

Cenospheres are hollow particles in fly-ash, a by-product of coal burning, and are widely used as reinforcement for developing low density composites called syntactic foams. This study investigates the physical, chemical, and thermal properties of cenospheres obtained from 3 different sources, CS1, CS2, and CS3, for the development of syntactic foams. Description of floatation method to separate broken particles is given, and it was seen that up to 11 % of the particles were damaged. Post heat treatment samples show development of SiO2 phase in the cenosphere, which is not present in the as received product. CS3 had the highest quantity of Si element, compared to the other two, showing the difference in the source quality. The particle size distribution for CS2 is very narrow while for the others is much broader. All censopheres have porous walls but the morphology of CS2 is the most uniform and smooth. For the application of metallic layer and subsequent consolidation via spark plasma sintering, CS2 was deemed the most physically, thermally, and chemically suitable.

Pronematus ubiquitus (McGregor) is a small iolinid mite that is capable of establishing on tomato plants. Once established, this mite has been shown to control both tomato russet mite, Aculops lycopersici (Tryon) (Acari: Eriophyidae) and tomato powdery mildew (Oidium neolycopersici L. Kiss). In the present study, we explored the nutritional value of various food sources in the laboratory. First, we assessed the reproduction of two food sources that P. ubiquitus can encounter on a tomato crop: tomato pollen and powdery mildew. In a second laboratory experiment, we evaluated the nutritional value of two types of prey mites: the astigmatid Carpoglyphus lactis L. (Acari: Carpoglyphidae) and the tarsonemid Tarsonemus fusarii (Acari: Tarsonemidae). Powdery mildew and C. lactis did not contribute to the reproduction, whereas tomato pollen and T. fusarii did allow egg-laying. However, Typha angustifolia pollen was a superior food source in both experiments. In a greenhouse trial on individual caged tomato plants, we evaluated the impact of pollen supplementation frequency on establishment of P. ubiquitus. Here, a pollen addition frequency of every other week was required to allow populations of P. ubiquitus to establish.

When the antioxidants in our immune system cannot neutralize or convert Reactive oxygen species into safe molecules at the rate at which it is produced then this imbalance is termed as “oxidative stress”. It is related with a wide array of diseases that includes cancer, diabetes, cardiovascular diseases, hypertension etc. These ROS species however are utmost essential for the proper functioning of human body which are produced as a consequence of partial oxidation of cellular metabolism performing essential functions such as protein phosphorylation, activation of several transcriptional factors, apoptosis, immunity, and differentiation. The sources by which these are produced can be broadly classified are intrinsic and extrinsic sources. There are variety of natural antioxidant enzymes of human body that combat against this oxidative stress. The extrinsic sources of ROS include the use of natural plants, extracted flavonoids and vitamins. In this review we will briefly explain how the sources of ROS, its essential function in human body, its elevation and associated damage to organs and effect on various diseases, and a hope of finding a way of how this oxidative stress can be exploited for therapeutic potential.

With the outbreak of the COVID-19 disease, the research community is producing unprecedented efforts dedicated to better understand and mitigate the affects of the pandemic. In this context, we review the data integration efforts required for accessing and searching genome sequences and metadata of SARS-CoV2, the virus responsible for the COVID-19 disease, which have been deposited into the most important repositories of viral sequences. Organizations that were already present in the virus domain are now dedicating special interest to the emergence of COVID-19 pandemics, by emphasizing specific SARS-CoV2 data and services. At the same time, novel organizations and resources were born in this critical period to serve specifically the purposes of COVID-19 mitigation, while setting the research ground for contrasting possible future pandemics. Accessibility and integration of viral sequence data, possibly in conjunction with the human host genotype and clinical data, are paramount to better understand the COVID-19 disease and mitigate its effects.

In recent years, tremendous progress has been made in the development of rare-earth ion doped tellurite glass laser sources, ranging from watt and multiwatt level fiber lasers to nanowatt level microsphere lasers. Significant success has been achieved in extending the spectral range of tellurite fiber lasers generating at wavelengths beyond 2 μm as well as in theoretical understanding. This review is aimed at discussing the state of the art of neodymium-, erbium-, thulium-, and holmium-doped tellurite glass fiber and microsphere lasers.

The recyclability of polystyrene, acrylonitrile butadiene styrene, polystyrene and polyvinylchloride waste and using them as a source for 3D printing were studied. Filaments of about 3 mm in diameter were extruded successfully with a small-size extruder. The processed filaments were tested on a broad range of parameters - glass transition temperature, tensile properties and a pyrolysis scenario were obtained. The measured parameters were compared with parameters of virgin counterparts presented in the literature. In order to estimate the toxicity of the recycled material, elemental analysis of the samples was done.

Ruminant mammals extract nutrients from plant-based food through fermentation in the rumen; fiber and starch are pre-digested by microorganisms and methane is produced as a by-product, which released into the atmosphere acts as a potent greenhouse gas. In an effort to reduce enteric methanogenesis, dietary additives for ruminants have been investigated, and marine macroalgae have proven particularly promising, e.g., the inclusion of 0.2% dry matter of the red alga A. taxiformis into cow feed decreased in vivo methane production by up to 98%. Thus, if globally applied, the addition of algae in ruminant diets could revolutionize the management of greenhouse gas emissions across the livestock sector. However, the ozone-depleting nature of halogen compounds produced in Asparagopsis sp. and the reported adverse health impacts on humans, along with impracticability issues and the difficulty to produce, commercialize and distribute algae widely, has sown some doubt on the feasibility of using macroalgae as methane mitigation instruments. To circumvent such obstacles, and taking into account the paradigm that eukaryotic hosts cannot be understood without considering interactions with their associated microbiome, the exploration of marine algae associated microorganisms is anticipated. Following the notion that in the close and intimate relationships between algae-hosts and their microbiota the origin of chemical response mechanisms is often unclear, and that compounds initially assigned to algae have previously been shown to stem from host-associated microbes, it is not unreasonable to think that these may be involved in the antimethanogenic effects of marine algae in the rumen. Once identified, such microorganisms could lead to antimethanogenic feed additives, and reduce enteric methanogenesis from livestock ruminants substantially. This review is three-fold: it provides a brief, historic overview of macroalgae as feed supplements for ruminants, sums up the difficulties related to using whole-macroalgae as large-scale antimethanogenic feed additives, and describes the macroalga microbiome, including its potential to serve as an antimethanogen for enteric fermentation.

Since a large amount of sewage sludge (WSS) has been generated daily, it is necessary to explore effective methods for utilizing WSS. Although a photo-fermentation system sometimes alters the characteristics of microbial functions, there are no attempts to perform the photo-fermentation using WSS which is regularly treated under a dark-fermentation style. In this study, the effect of photo-fermentation (photo-irradiation) on anaerobic digestion using WSS was revealed. Photo-irradiation during the anaerobic digestion of WSS significantly reduced the amount of organic acids and hydrogen sulfide and methane production was also suppressed. However, it was shown that the activity of sulfate-reducing bacteria in WSS under the light treatment increased. Photo-irradiation also stimulated the growth of green-sulfur bacteria and induced anoxygenic photosynthesis, by which the fermented samples turned green linking with the consumption of hydrogen sulfide. Finally, a dark/light switching fermentation was able to reduce only hydrogen sulfide while methane production remained the same.

The effect of legumes adapted to a temperate climate on gas production kinetics, enteric methane, and rumen fermentation in vitro was evaluated. The species studied were Acacia dealbatha, Acacia melanoxylon, Albizzia lopantha, Lupinus pubescens, Inga insignes, Senna multiglandulosa and Tecoma stans. The effective degradation of the dry matter was estimated, the in vitro gas production was measured up to 120 hours of incubation, and the production of enteric methane, VFAs, and ammonia were measured at 24 hours. Dry matter, organic matter, ash, crude protein, neutral detergent fiber, acid detergent fiber, and acid detergent lignin were evaluated. The content of total phenols and condensed tannins was quantified. To determine digestibility, the samples were incubated for up to 120 hours. I. insignes presented a higher dry matter content and a high crude protein content. L. pubescens presented low dry matter digestibility. The neutral detergent fiber content was higher in I. insignes and with a higher value in dry matter digestibility and lower content of total phenols and condensed tannins. While S. multiglandulosa showed low detergent acid fiber content. The acid detergent lignin value was higher in I. insignes and lower in L. pubescens. In vitro gas and enteric methane production was higher in L. pubescens. propionic acid and ammonia they were higher in S. multiglandulosa. It is concluded that the amount of secondary compounds affects methane production, compromises digestibility and rumen kinetics of the legumes studied.