Effective and rapid mixing is essential for various chemical and biological assays. The present work reports a simple and low-cost micromixer based on magnetofluidic actuation. The device takes advantage of magnetoconvective secondary flow, a bulk flow induced by an external magnetic field, for mixing. A paramagnetic stream of diluted ferrofluid and a non-magnetic stream are introduced to a straight microchannel. A permanent magnet placed next to the microchannel induced a non-uniform magnetic field. The magnetic field gradient and the mismatch in magnetic susceptibility between the two streams create a body force, which leads to rapid and efficient mixing. The micromixer reported here could achieve a high throughput and a high mixing efficiency of 90 % in a relatively short microchannel.

Nanoporous membranes promise energy-efficient water desalination. Hexagonal boron nitride (h-BN), like graphene, exhibits outstanding physical and chemical properties, making it a promising candidate for water treatment. We employed Car–Parrinello molecular dynamics simulations to establish accurate modeling of Na+ and Cl- permeation through hydrogen passivated nanopores in graphene and h-BN membranes. In these complex systems the classical potentials cannot properly account for the physics at play. We demonstrate that ion separation works well for the h-BN by imposing a barrier of 0.13 eV and 0.24 eV for Na+ and Cl- permeation respectively, compared to the graphene where the Cl- ion faces a negative barrier of 0.68 eV and is prone toward blockade and Na+ permeation is associated with a slightly negative barrier of 0.03 eV. From the change in the solvation shell, we get the following trend: Na/h-BN > Na/G > Cl/G > Cl/h-BN. We argue that the trend in the permeation barrier changes to Cl-h-BN > Na-h-BN > Na-G > Cl-G due to a combination of several interactions, including the distortion of the water network induced by the ions, the ion-water interaction, and the ion-nanopore interaction. Overall, the desalination performance of h-BN surpasses that of their graphene counterparts.

Surface acoustic wave (SAW) is effective for the manipulation of fluids and particles in microscale. The current approach of integrating interdigitated transducers (IDTs) for SAW generation into microfluidic channels involves complex and laborious microfabrication steps. These steps often require the full access to clean room facilities and hours to align the transducers to the precise location. This work presents an affordable and innovative method for fabricating SAW-based microfluidic devices without the need of clean room facilities and alignment. The IDTs and microfluidic channels are fabricated in the same process and thus precisely self-aligned in accordance with the device design. With the use of the developed fabrication approach, a few types of different SAW-based microfluidic devices have been fabricated and demonstrated for particle separation and active droplet generation.

A portable laser photoacoustic sensor based on a Field-Programmable Gate Array (FPGA) is reported for methane detection. A tunable DFB diode laser in the 1654 nm wavelength range is used as an excitation source. The photoacoustic signal processing was implemented by a FPGA device. A small resonant photoacoustic cell is designed. The minimum detection limit (1σ) of 10 ppm for methane (CH₄) is demonstrated.

Due to their wide range of uses in modern technology, nanomaterial’s of silver metallic (Ag-NPs) have engaged considerable concern, driving significant research with development efforts. This study focuses on investigating the antimicrobial properties of Ag-NPs, encompassing their production, characterization, and biological aspects. The eco-friendly extracellular biosynthetic method employed in this work utilized extracts from the marine fungus Aspergillus flavus MK4 as reducing agents for nanoparticle synthesis. Analyzing the colloidal Ag-NPs using UV-visible spectroscopy revealed a peak in absorbance at 460 nm, indicating the presence of plasmonic properties. The electrons imaging of internal structure (TEM) elucidated spherical shape of the Ag-NPs by 15 nm size. Testing against bacterial diversities (Gr-ve & Gr+ve) revealed potent antibacterial and antifungal efficacy. Cytotoxicity versus HepG-2 cell line was assessed using the MTT assay, and antioxidant properties were examined through the radical scavenging (DPPH) assay. In wise of their conceivable applications in the fields of antibacterial, anticancer, and wound-healing, the Ag-NPs that were synthesized exhibit promising features. With its powerful ability to synthesize silver nanoparticles (Ag-NP), Aspergillus flavus MK4 Aspergillus flavus MK4 can generate nanoparticles extensively characterized, demonstrating their antibacterial, antioxidant, anticancer, and wound-healing properties.

Based on the need for real-time sag monitoring of Overhead Power Lines (OPL) for electricity transmission, this article presents the implementation of a hardware and software system for online monitoring of OPL cables and cable sag determination. The mathematical model based on differential equations and the methods of algorithmic calculation of OPL cable sag are presented. Considering that, based on the mathematical model presented, the calculation of OPL cable sag can be done in different ways depending on the sensors used, and the presented application uses a variety of sensors. Therefore, a direct calculation is made using one of the different methods. Subsequently, the verification relations are highlighted directly and, respectively, the calculation by the alternative method, which uses another group of sensors, to generate both a verification of the calculation and the functionality of the sensors, thus obtaining a defect observer of the sensors. The hardware architecture of the OPL cable online monitoring application is presented, together with the main characteristics of the sensors and communication equipment used. The configurations required to transmit data using the ModBUS and ZigBee protocols are also presented. The main software modules of the OPL cable condition monitoring application are described, which ensure the monitoring of the main parameters of the power line and the visualisation of the results both on the electricity provider's intranet using a web server and MySQL database, and on the Internet using an Internet of Things (IoT) server. This categorisation of the data visualisation mode is done in such a way as to ensure a high level of cyber security. Starting from the mathematical model of the OPL cable sag calculation, it goes through the stages of creating such a monitoring system, from the numerical simulations carried out using Matlab to the real-time implementation of this monitoring application. The main modules of the application software are: the software module for reading quantities from the sensor network through a ModBUS Input/Output (I/O) server, the software module for real-time calculation of the OPL cable sag, the software module for read/write operations based on MySQL type data, the software module for transferring data to the user's intranet through a web server, and the software module for viewing data by authorised users based on user and password through an IoT server. The development software environments used are Matlab and Laboratory Virtual Instrument Engineering Workbench (LabVIEW).

The ability to detect the presence as well as classify the activities of individuals behind visually obscuring structures is of significant benefit to police, security and emergency services in many situations. This paper presents the analysis from a series of experimental results generated using a through-the-wall (TTW) Frequency Modulated Continuous Wave (FMCW) C-Band radar system named Soprano. The objective of this analysis was to classify whether an individual was carrying an item in both hands or not using micro-Doppler information from a FMCW sensor. The radar was deployed at a standoff distance, of approximately 0.5 m, outside a residential building and used to detect multiple people walking within a room. Through the application of digital filtering, it was shown that significant suppression of the primary wall reflection is possible, significantly enhancing the target signal to clutter ratio. Singular Value Decomposition (SVD) signal processing techniques were then applied to the micro-Doppler signatures from different individuals. Features from the SVD information have been used to classify whether the person was carrying an item or walking free handed. Excellent performance of the classifier was achieved in this challenging scenario with accuracies up to 94%, suggesting that future through wall radar sensors may have the ability to reliably recognize many different types of activities in TTW scenarios using these techniques.

Ti and its alloys are the most commonly used materials for biomedical applications. However, bacterial infection after implant placement is still one of the significant rising complications. Therefore, the application of the antimicrobial agents into implant surfaces to prevent implant-associated infection has attracted lots of attention. Scientific papers have shown that inorganic antibacterial metal element (e.g. Ag, Cu, Zn) can be introduced to implant surfaces with the addition of metal nanoparticles or metallic compounds into electrolyte via micro-arc oxidation (MAO) technology. In this review, the effects of the composition and concentration of electrolyte and process parameters (e.g. voltage, current density, oxidation time) on morphological characteristics (e.g. surface morphology, bonding strength), antibacterial ability and biocompatibility of MAO antimicrobial coating were discussed in detail. Anti-infection and osseo-integration can be simultaneously accomplished with the selection of the proper antibacterial elements and operating parameters. Besides, MAO assisted by magnetron sputtering (MS) to endow Ti-based implant materials with superior antibacterial ability and biocompatibility was also discussed. Finally, the development trend of MAO technology in the future was forecasted.

Metal and alloy toughening was the core and long-term research direction in materials filed. As grain size had bimodal distribution, micro/nano-structured alloys presented excellent comprehensive mechanical properties, and this had become one of the research hotspots and developing trends in the field of nanotechnology. In-situ tensile test was a direct and effective method to study the deformation mechanism of materials, which revealed the multiple mechanisms responding to feature grain sizes and provided reliable experimental means and research technique. Research on development of in-situ technique and its applications in mechanical properties was reviewed in this paper according to the recent advances on the modern mechanical properties for high strength and high plasticity alloy at home and abroad. The disadvantages of the present study of preparation methods and investigation techniques for high-performance alloy had been concluded. Finally, the development prospects of high strength and high plasticity alloy materials were analyzed.

In this study, the mechanical and piezoresistive properties of mortars reinforced with carbon nanotubes (CNTs) and carbon micro fibers (CMFs) are determined. Silica fume as well as a polymer with polyalkylene glycol graft chains were used as dispersant agents for the CNTs and CMFs incorporation into the cement paste. The mechanical properties of the mortar composites were investigated in respect to their flexural and compressive strength. A four-probe method was used for the estimation of their piezoresistive response. The test outcomes revealed that the combination of the dispersant agents along with a low content of CNTs and CMF by weight of cement (bwoc) result in the production of a stronger mortar with enhanced mechanical performance and durability. More specifically, there was an increase in flexural and compressive strength up to 38% and 88%, respectively. Moreover, the piezoresistive response of the reinforced cementitious materials was attributed to the variation of electrical resistivity due to tunneling transport of electrons stemming from two different mechanisms due to the incorporation of the conductive admixtures (CNTs and CMF). This work aims to contribute to the progress acceleration in the field of developing structural materials with self-sensing and electrical actuation related properties.

Microscopic vision plays an important role in automated micro-assembly. However, some uncertain factors in the assembly process, such as occlusion and stains can lead to the mistakes of feature extraction. Herein, to solve the problem, the deep learning techniques are introduced into the feature recognition tasks, focusing on the attention mechanism and visualizing CNNs for DL-based microscopic vision. The main contributions are summarized as follows: The CBAM attention mechanism is combined with the YOLOv5 algorithm to improve the accuracy and robustness of feature extraction. The micropart feature occlusion experiment results show that at 70% occlusion degree, YOLOV5-CBAM can reach 97.9% [email protected], which is 4.6% higher than the original one. Visualization analysis of DL-based model is conducted using Grad-CAM to make the decision result more transparent and avoid potential visual detection risks during assembly. The heatmap matching degree between GT area and high-light area is increased by 27.81% on average, which further verify the effectiveness of attention mechanism in micropart feature localization. Additionally, micropart surface stain and droplet quality classification models based on ResNet50 are trained to replace the manual sorting. The visual results are consistent with human eye discernment and judgement, confirming the reliability of parts and droplets sorting.

Objectives: Social distancing measures are currently implemented to control COVID-19 pandemic in many countries, including Saudi Arabia. The aim of this study was therefore to evaluate the awareness and adherence of the Saudi population to these measures. Methods: A web-based questionnaire was designed with 16 questions (8 questions related to demographics, 3 in relation to awareness about social distancing and 5 related to overall practice of social distancing). Results: 5105 participants completed the survey [58.4% female, 66.3% young individuals (aged 18-37 years), 55.8% bachelor degree holders, and 51.0% from the western region]. The Saudi Ministry of Health (MOH) was the main source of information about COVID-19 for most participants (78.2%). High awareness (81.3%) regarding social distancing was observed, associated mainly with female participants, those from the middle region and those with high education and income. Overall implementation of social distancing was satisfactory (score 3.13/5), with 37.8% never leaving home during the home-stay period. Better adherence to social distancing was observed for female participants, higher degree holders and those aged over 38 years. Conclusions: Organised plans by the Saudi MOH have been effective in raising awareness and improving practice of social distancing among public. However, the observed lower practice of social distancing by individuals with lower education and income indicates the need for targeted interventions to achieve better outcome.

Intermetallic compounds are increasingly being expected to utilize in tribological environments, but to date the works are hindered by insufficient ductility at low and medium temperature. This paper presents a novel multiphase intermetallic alloy with the chemical composition of Mo-40Ni-13Si (at.%). Microstructure characterization reveals that a certain amount of ductile Mo phases formed during the solidification process of ternary Mo-Ni-Si alloy melt, which is undoubtedly beneficial to the ductility improvement of intermetallic alloy. Tribological properties of the designed alloy, including wear resistance, friction coefficient and metallic tribological compatibility, were evaluated under dry sliding wear test conditions at room temperature. Results suggested that the multiphase alloy possesses an excellent property for room-temperature wear applications, which is attributed to the unique microstructural features and thereby good combination in hardness and ductility. The corresponding wear mechanism is also reported by observing the worn surface, subsurface and wear debris of alloy, which to be found is soft abrasive wear.

This paper reports on the production and mechanical properties of Ti6Al4V micro-lattice structures, with strut thickness nearing the single-track width of the laser-based powder bed fusion (LPBF) system used. Besides providing new information on the mechanical properties and manufacturability of such thin-strut lattices, this paper also reports on the in-situ deformation imaging of micro-lattice structures with 6 unit cells in every direction. LPBF lattices are of interest for medical implants, due to the possibility of creating structures with an elastic modulus close to that of the bones and small pore sizes which allow effective osseointegration. In this work four different cubes were produced by laser powder bed fusion and subsequently analyzed using microCT, compression testing and one selected lattice was subjected to in-situ microCT imaging during compression. The in-situ imaging was performed at 4 steps during yielding. The results indicate that mechanical performance (elastic modulus and strength) correlate well with actual density and that this performance is remarkably good, despite the high roughness and irregularity of the struts at this scale. In-situ yielding is visually illustrated.

By using the particle swarm optimization algorithm for crystal structure prediction, we reveal a newly orthorhombic Cmcm structure of HfB4, which is more energetically superior to the previously proposed YB4-, ReP4-, FeB4-, CrB4-, and MnB4-type structures in the considered pressure range. The phonon dispersion and elastic constants calculations confirm that the new phase is dynamically and mechanically stable. The calculated large shear modulus (240 GPa) and high hardness (45.7 GPa) imply that the predicted Cmcm-HfB4 is a potential superhard material. Meanwhile, the directional dependences of the Young's modulus, bulk modulus, and shear modulus for HfB4 are systematically investigated. Further analyses of the density of states and electronic localization function indicate that the strong B-B and B-Hf covalent bonds greatly contribute to its high hardness and stability.

In this paper, we present an experimental procedure to enhance the dimensional accuracy of fabrication via Stereolithography (SLA) of features at the micro-scale. Using a custom benchmark part, deviations in feature dimensions (micro-pores diameters and depths) were detected and measured by confocal microscopy. Samples characterization and experimental observations allowed the identification of inaccuracy sources, mainly due to the laser beam scanning strategy and to the incomplete removal of uncured liquid resin in post-processing (i.e., IPA washing). As a technology baseline, the measured dimensional errors on pores diameters were up to -46%. A compensation method of the nominal laser spot diameter (85m) was defined and implemented resulting in relevant improvements in dimensional accuracy of 9.8% and 11.3% on full-open pores diameter and depth, respectively. Further investigation was performed on a customized test part to adjust the calibration procedure. The measurements revealed that the estimate of the laser beam spot size is 968m. Measurements on micro-pores having different sizes revealed that a constant compensation parameter (i.e., C=85, 96, 120m) is not fully effective at the micro-scale, where average errors still remain at -24%, -18.8%, and -16% for compensations equals to 85, 96 and 120m, respectively. A further experimental campaign allowed the identification of an effective nonlinear compensation law where the compensation parameter depends on the micro-feature size C= f (D). Results show a sharp improvement in dimensional accuracy on micro-pore fabrication, with errors consistently below +8.2%. The proposed compensation method can be extended for the fabrication of any micro-features without restrictions on the specific technology implementation. Concerning the inaccuracy introduced by the laser path, experimentation with a customized part allowed the optimization of the part orientation to reduce the errors and their differences along the X and Y machine axes.

GaN ultraviolet photodetector with metal-semiconductor-metal structure is achieved by growing on a periodic trapezoid column-shape patterned sapphire substrate using metalorganic chemical vapor deposition. Under 5-V reverse bias, the photodetector fabricated on such patterned sapphire substrate exhibits a lower dark current, a higher photocurrent, and a 476 % enhancement in the maximum responsivity as compare with those of the photodetector fabricated on conventional flat sapphire substrate. It is also found that the much larger UV-to-visible rejection ratio and the fact that responsivity drops in a smaller cut-off region are observed from photodetector fabricated by using a periodic trapezoid column-shape patterned sapphire substrate. These phenomena may all be attributed to the reduction of threading dislocation density and the improved quality of GaN film, as well as the internal reflection and/or scattering effect on the interface between GaN film and the periodic trapezoid column-shape pattern of the substrate.

The influence of growth temperature on the crystalline quality and optical properties of AlGaN at 325 nm, grown using plasma-assisted molecular beam epitaxy (MBE), was investigated. The growth temperature exhibited a significant impact on the growth mode and surface morphology. Specifically, at a growth temperature of 750 degrees Celsius, when appropriate Al and Ga flow rates were employed, the AlGaN layer exhibited exceptional surface morphology and favorable optical properties. The optical properties of the AlGaN material were explored, revealing the presence of two distinct non-radiative recombination centers characterized by different activation energies. The minority carrier lifetimes were measured as 560 ps at 10 K and 64 ps at room temperature. The underlying mechanism was analyzed from the perspective of carrier dynamics, shedding light on the observed phenomena.

Dehydroaromatization of methane (MDA) is of great interest as a promising process for processing natural and associated petroleum gases, the main component of which is methane. The rapid loss of catalyst activity because of coke formation hinders the introduction of the DHA methane process into industry. Therefore, the aim of the research was to find ways to improve Mo/ZSM-5 catalysts for MDA. The paper presents the results of the synthesis of high-silica zeolites of the ZSM-5 type with a microporous and micro-mesoporous structure, the preparation of Mo/ZSM-5 catalysts based on them, and the study of the physicochemical and catalytic properties of the obtained samples during the non-oxidative conversion of methane into aromatic hydrocarbons. Zeolite catalysts were investigated by IR spectroscopy, X-ray diffraction, TPD-NH3, SEM, HR-TEM, N2-adsorption. It was found that the addition of carbon black at the stage of synthesis of zeolite type ZSM-5 does not lead to structural changes, the obtained samples have a crystallinity equal to 100%. The creation of the micro-mesoporous structure in Mo/ZSM-5 catalysts lead to an increase in their activity and stability in the process of methane dehydroaromatization. The highest conversion of methane is observed on a 4.0%Mo/ZSM-5 catalyst prepared based on of zeolite synthesized using 1.0% carbon black, and is 13.0% in 20 minutes of reaction, while the benzene yield reaches 7.0%. It has been shown by HR-TEM that a more uniform distribution of the active metal component is observed in a zeolite catalyst with a micro-mesoporous structure than in a microporous zeolite.

The main purpose of this work was to tests of form and size of fatigue wear of the top layer of oil gear pump wheel (3PW-BPF-24). The object of tests was operated during a determined number of hours at strictly controlled operational and environmental parameters. A microscope of focal differentiation by Alicona InfiniteFocus G4 (with Focus-Variation optical measuring technology) was used for an identification, measurement and description of noticed superficial defects, which resulted from the fatigue process of the top layer and an earlier thermochemical treatment. The work was finished with an analysis of obtained results (based on the analysis of 3D scans) and conclusions concerning about optimization of the thermal treatment. Taking into consideration the presented results (suggestions) in the technology of improving strength properties of gear wheels (of this type oil pumps) may render it possible to obtain an appropriate fatigue endurance of the top layer, i.e. a minimization of observed superficial defects.

Mannosylerythritol lipids (MELs), one of the most promising biosurfactants (BS), are glycolipids produced by yeasts or fungi, with great environmental performance and a high compatibility with the human body. MELs besides working as typical surfactants, can form diverse structures when in the critical aggregation concentration (CAC), reducing the surface tension of water and other solutions, and being stable over a wide range of conditions. Among others, MELs present anti-microbial, antitumor, antioxidant and anti-inflammatory activity, skin and hair repair capacity, which opens possibilities for their use in applications from cosmetics and pharmaceutics to bio-remediation and agriculture. However, their market share is still low when compared to other glycolipids, due to their less developed production process and higher production cost. This re-view gathers information on the potential applications of MELs mentioned on the literature since 1993. Furthermore, it is also explored the current strategies being developed to enhance the market presence of MELs, in parallel with the ones developed for rhamnolipids and sophorolipids.

Tellurium exhibits exceptional intrinsic electronic properties. However, investigations into the modulation of tellurium's electronic properties through physical modification are notably scarce. Here, we present a comprehensive study focused on the evolution of the electronic properties of tellurium crystal flakes under plasma irradiation treatment by employing conductive atomic force microscopy and Raman spectroscopy. The plasma-treated tellurium experienced a process of defect generation through lattice broken. Prior to the degradation of electronic transport performance due to plasma irradiation treatment, a remarkable observation emerged: in the low-energy region of hydrogen plasma-treated tellurium, a notable enhancement in conductivity was unexpectedly detected. The mechanism underlying this enhancement in electronic transport performance was thoroughly elucidated by comparing it with the electronic structure induced by argon plasma irradiation. This study not only fundamentally uncovers the effects of plasma irradiation on tellurium crystal flakes, but also unearths an unprecedented trend of enhanced electronic transport performance at low irradiation energies when utilizing hydrogen plasma. This abnormal trend bears significant implications for guiding the prospective application of tellurium-based 2D materials in the realm of electronic devices.

The application of metal-matrix composite coatings for protecting and improving the service life of sliding components has demonstrated to have the potentials of meeting the requirements of a diverse range of engineering industries. Recently, a significant body of research has been devoted to study the mechanical and tribological performance of dispersion-strengthened MCrAlY coatings. These coatings belong to a class of emerging wear-resistant materials, offering improved properties and being considered as promising candidates for the protection of engineering structural materials exposed to tribological damage, especially at elevated temperature regimes. This paper attempts to comprehensively review the different reinforcements used in the processing of MCrAlY-based alloys and how they influence the mechanical and tribological properties of the corresponding coatings. Further, the major fabrication techniques together with their benefits and challenges are also reviewed. Discussion on the failure mechanisms of these coatings as well as the main determining factors are also included. In addition, a comprehensive survey of studies and investigations in recent times are summarized and elaborated to further substantiate the review.

Micro-arc oxidation (MAO) is an emerging technology employed to produce high hardness or anti-corrosion ceramic coatings on lightweight metals such Al, Ti, Mg and their respective alloys. However, under non-lubrication conditions, such coatings exhibit relatively high friction coeffi-cients. To enhance the friction reduction properties of the MAO coatings, we employed a one-step MAO process with varying concentrations of graphene oxide (GO) in an aluminate sys-tem electrolyte to create composite coatings on the surfaces of Ti-6Al-4V alloy. The effect of concentrations of GO particles on microstructure, composition, and wear behavior of the result-ing composite coatings was investigated. Measurements of the coating's thickness, hardness, and roughness have also been conducted. Ball-on-disk friction test under dry condition were carried out to reveal tribological behavior of the MAO coating. The addition of graphene oxide in the electrolyte reduces the friction coefficient, with the composite coating containing 5 g/L of GO particles displaying the most effective friction reduction. Moreover, coating thickness increases with higher GO concentration. This friction reduction can be attributed to the particles in the coating acting as lubricants during friction, while GO also reduces adhesive damage, shifting the wear mechanism from adhesive to abrasive.

It is important to add second- or third-phase materials to improve the physical, mechanical, and biodegradable properties of polypropylene (PP) nanocomposites. A unique hybrid bio-nanocomposite was fabricated using microparticle cellulose powder from wastepaper with a polypropylene (PP) polymeric matrix using a low-shear chaotic mixing method. A small amount (2-5%) of layered micro clay was also added to investigate the hybrid effect of nanocomposite fabrication on the mechanical properties. A low-shear chaotic melt mixing method induces the formation of nano cellulose structures and layered clay nanoparticles by via exfoliation. The nanoparticles were characterized using Fourier transform infrared (FTIR) spectroscopy. Mechanical properties such as the flexural strength (FS) and tensile strength (TS) were investigated using an Izod impact tester (IZ), and a dynamic mechanical testing analyzer (DMTA). Further, scanning electron microscopy (SEM) was used to observe the microstructure of the nanocomposite. In addition, differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA) were conducted to investigate the crystallinity and degradation of the samples, respectively. The addition of wastepaper cellulose powder below 2.5 wt. % did not improve the mechanical properties, however, improvements were observed when more than 5wt.% wastepaper cellulose powder was added. With the addition of a small amount of nano-clay, the mechanical properties were significantly improved, and a synergistic effect could be noticed. The observed results were then compared with PP-clay nanocomposites used in automotive industries to replace cellulose nanocomposites. The application areas can also cover lead production in paper cups and vacuum foaming.

The properties of the annual, semiannual and triennial oscillations (AO, SAO and TO) in the middle atmosphere have been investigated using the TIMED/SABER temperature data. The Lomb-Scargle and wavelet spectra were used to determine the dominant oscillations in the background temperature field. The AO is prominent at the mid-latitudes. The AO amplitudes present an asymmetry between the two Hemispheres, being larger in the mesosphere than in the stratosphere. The SAO dominates the tropical regions, with three amplitude maxima at altitudes of 45, 75, and 85 km. The SAOs in the upper mesosphere (75 km) are out of phase with those in the mesopause (85 km) in the tropical regions, which can generate an enhancement of 11 K at each equinox, contributing to the lower mesospheric inversion layer. The TO is significant in the tropical region, with amplitude being maximum at 35, 45 and 85 km. Result shows that there may be potential interaction by the TO with SAO at 85km at the equator. The relation between ENSO and TO has also been discussed. The ENSO signal may modulate the amplitude of the TO, mainly in the lower stratosphere. The real origin of the TO may lie in the wave-mean-flow interaction.

Negative temperature coefficient (NTC) materials are usually based on ceramic semiconductors and electrons are involved in their transport mechanism. A new type of NTC material, adequate for alternating current (AC) applications, is represented by zeolites. Indeed, zeolites are single-charge carrier ionic conductors with a temperature-dependent electrical conductivity. In particular, electrical transport in zeolites is due to the monovalent charge-balancing cations, like K⁺, capable of hopping between negatively charged sites in the aluminosilicate framework. Owing to the highly non-linear electrical behavior of the traditional electronic NTC materials, the possibility to have alternative types of materials, showing linearity in the electrical behavior, is very desirable. Among different zeolites, the natural clinoptilolite has been selected for investigating the NTC behavior since it is characterized by high zeolite content, convenient Si/Al atomic ratio, good mechanical strength, due to its compact microstructure, and low toxicity. Clinoptilolite has shown a rapid and quite reversible impedance change under heating, characterized by a linear dependence on temperature. X-ray diffraction (XRD) has been used to identify the natural zeolite, to establish all types of crystalline phases present in the mineral, and to investigate the thermal stability of these phases up to 150°C. X-ray photoelectron spectroscopy (XPS) analysis has been used for the chemical characterization of the natural clinoptilolite sample, providing important information on the cationic content and framework composition. In addition, since electrical transport takes place in the zeolite free-volume, a Brunauer–Emmett–Teller (BET) analysis of the mineral has been also performed.

Microwave technology has a potential application in the extraction of zinc from sulphide ores, knowledge of the dielectric properties of these ores plays a major role in the microwave design and simulation for any process. The dielectric properties of zinc sulfide concentrate for two different apparent densities—1.54 and 1.63 g/cm³—have been measured by using the resonance cavity perturbation technique at 915 and 2450 MHz during the roasting process for the temperature ranging from room temperature to 850 °C. The variations of dielectric constant, the dielectric loss factor, the dielectric loss tangent and the penetration depth with the temperature, frequency and apparent density have been investigated numerically. The results indicate that the dielectric constant increases as the temperature increases and temperature has a pivotal effect on the dielectric constant, while the dielectric loss factor has a complicated change and all of the temperature, frequency and apparent density have a significant impact to dielectric loss factor. Zinc sulfide concentrate is high loss material from 450 to 800 °C on the basis of theoretical analyses of dielectric loss tangent and penetration depth, its ability of absorbing microwave energy would be enhanced by increasing the apparent density as well. The experimental results also have proved that zinc sulfide concentrate is easy to be heated by microwave energy from 450 to 800 °C. In addition, the experimental date of dielectric constant and loss factor can be fitted perfectly by Boltzmann model and Gauss model, respectively.

It is important to add second- or third-phase materials to improve the physical, mechanical, and biodegradable properties of polypropylene (PP) nanocomposites. A unique hybrid bio-nanocomposite was fabricated using microparticle cellulose powder from wastepaper with a polypropylene (PP) polymeric matrix using a low-shear chaotic mixing method. A small amount (2-5%) of layered micro clay was also added to investigate the hybrid effect of nanocomposite fabrication on the mechanical properties. A low-shear chaotic melt mixing method induces the formation of nano cellulose structures and layered clay nanoparticles by via exfoliation. The nanoparticles were characterized using Fourier transform infrared (FTIR) spectroscopy. Mechanical properties such as the flexural strength (FS) and tensile strength (TS) were investigated using an Izod impact tester (IZ), and a dynamic mechanical testing analyzer (DMTA). Further, scanning electron microscopy (SEM) was used to observe the microstructure of the nanocomposite. In addition, differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA) were conducted to investigate the crystallinity and degradation of the samples, respectively. The addition of wastepaper cellulose powder below 2.5 wt. % did not improve the mechanical properties, however, improvements were observed when more than 5wt.% wastepaper cellulose powder was added. With the addition of a small amount of nano-clay, the mechanical properties were significantly improved, and a synergistic effect could be noticed. The observed results were then compared with PP-clay nanocomposites used in automotive industries to replace cellulose nanocomposites. The application areas can also cover lead production in paper cups and vacuum foaming.

In recent years, cerium dioxide (CeO2) has attracted considerable attention owing to its remarkable performance in various applications, including photocatalysis, fuel cells, and catalysis. This study explores the effect of nickel (Ni) doping on the structural, thermal, and chemical properties of CeO2 nanorods, particularly focusing on oxygen vacancy-related phenomena. Utilizing X-ray powder diffraction (XRD), alterations in crystal structure and peak shifts were observed, indicating successful Ni doping and the formation of Ni2O3 at higher doping levels, likely due to non-equilibrium reactions. Thermal gravimetric analysis (TGA) revealed changes in oxygen release mechanisms, with increasing Ni doping resulting in the release of lattice oxygen at lower temperatures. Raman spectroscopy corroborated these findings by identifying characteristic peaks associated with oxygen vacancies, facilitating the assessment of Ni doping levels. Overall, this study underscores the substantial impact of Ni doping on CeO2 nanorods, shedding light on tailored catalytic applications through modulation of oxygen vacancies while preserving the nanorod morphology.

The objective of the study was to analyse the antimicrobial susceptibility trends of Spanish porcine bacteria to quinolones, cephalosporins and polymyxins. Isolates of Actinobacillus pleuropneumoniae, Pasteurella multocida, and Escherichia coli were isolated from sick pigs from 2019 to 2022. Antimicrobial susceptibility test was determined by minimal inhibitory concentration (MIC) following internationally accepted methodology. MIC categorization was based on distributing the range of MIC values in four categories being category one the most susceptible (lowest MIC value) and four the less susceptible one (highest MIC value). Moreover, clinical susceptibility (susceptible/resistant) was also determined according to CLSI and EUCAST clinical breakpoints. A logistic and multinomial logistic regression model was used to analyze the susceptibility data for dichotomized and categorized MIC data, respectively for any pair of antimicrobial/microorganism. In general terms, the antimicrobial susceptibility of pig bacteria to these antimicrobials remained stable or increased in the last four years in Spain. In the case of A. pleuropneumoniae and quinolones, it was observed a significant temporal trend where isolates from 2020 had significantly increased odds of being more susceptible than isolates from 2019. In the case of E. coli and polymyxins, a significant temporal trend was observed where isolates from 2020 and 2021 had significantly increased odds of being more susceptible than isolates from 2019 and 2020, respectively. Finally, a significant odd of being less susceptible was only observed for cephalosporins and E. coli for 2020 versus 2019, stagnating for the rest of study period. These results provide sound data on critical important antimicrobials in swine medicine.

This study reports on the development of bio-based hydrophobic coatings for packaging papers through deposition of polyhydroxybutyrate (PHB) particles in combination with nanofibrillated cellulose (NFC) and plant wax. In a first approach, PHB particles in micrometer range (PHB-MP) were prepared through a phase-separation technique providing internally nanosized structures. The particles were transferred as a coating by dip-coating filter papers in the particle suspension, followed by sizing with a carnauba wax solution. This approach allowed partial to almost full surface coverage of PHB-MP over the paper surface resulting in static water contact angles of 105° to 122° and 129° to 144° after additional wax coating. In a second approach, PHB particles with submicron sizes (PHB-SP) were synthesized by an oil-in-emulsion (o/w) solvent evaporation method, and mixed in aqueous suspensions with 0 to 7 wt% NFC. After dip-coating filter papers in PHB-SP/NFC suspensions and sizing with a carnauba wax solution, static water contact angles of 112° to 152° were obtained. The intrinsic properties of the particles were analyzed by scanning electron microscopy, thermal analysis and infrared spectroscopy, indicating higher crystallinity for PHB-SP than PHB-MP. The chemical interactions between the more amorphous PHB-MP particles and paper fibers were identified as an esterification reaction, while the morphology of the NFC fibrillar network was playing a key role as binding agent in the retention of more crystalline PHB-SP at the paper surface, hence contributing to higher hydrophobicity.

Using pumps operating as turbines (PATs) offers the possibility of increasing the sustainability of water and energy systems by recovering the excess of energy that would be otherwise lost in pressure reducing valves or head loss chambers. In on-grid applications, there are many research works and implementations of PATs. However, there is still limited research for the optimization of efficiency and stability of PATs operating in off-grid systems. This work contributes to the development of stable direct current (DC) off-grid electric systems based on PATs, by optimizing and analysing the energy efficiency and stability for a wide range of operation. A self-excited induction generator (SEIG) coupled to the PAT is provided to cover the conventional type of electric ma-chines typically coupled to the hydraulic pumps. In this context, a methodology is proposed, based on the hydraulic, mechanical and electric subsystems, to define the PAT-SEIG operational area, to maximize energy conversion and the system efficiency. This will guarantee stable electric output quantities when operating in a DC off-grid system. In addition, an analytical model is proposed to estimate the PAT-SEIG operation under specific conditions. With this, water managers are suitable to design and optimize an off-grid PAT-SEIG system and to define the best hydraulic machines, electronic equipment, and all different control elements to maximize energy conversion within the target of operational limits. To develop and verify this new methodology, two micro PAT-SEIG setups were implemented in the hydraulic laboratory of IST/CERIS under typical operating conditions. The proposed solution proved to be resilient under a variable load regime. The system's maximum efficiency can be adapted using different capacitor values for the excitation of the SEIG, and the operational range is limited to the electric components. Considering the nominal efficiencies of the system’s components, the maximum p.u. efficiency obtained for each PAT-SEIG system were between 0.7 and 0.8 p.u.

The utilization of natural waxes to form oleogels has emerged as a new and efficient technique for structuring liquid edible oil into solid-like structures for diverse food applications. The objective of this study was to investigate the interaction between sunflower wax (SW) and monoglycerides (MGs) in olive oil oleogels and to assess their physical characteristics and storage stability. To achieve this, pure SW and a combination of SW with MGs in a 1:1 ratio were examined within a total concentration range of 6-12% w/w. The formed oleogels were characterized based on their microstructure, melting and crystallization properties, textural characteristics, and oxidative stability during storage. All the oleogels were shelf-stable, and as the concentration increased, the hardness of the oleogels also increased. The crystals of SW oleogels were long needle-like, while the combination of SW and MGs led to the formation of crystal aggregates and rosette-like crystals. The differential scanning calorimetry and FTIR showed that the addition of MGs led to different crystal structures. The oxidation results revealed that oleogels had low peroxide and TBARS values throughout the 28-day storage. These results provide useful insights about the utilization of SW and MGs oleogels for potential applications in the food industry.

We aimed to investigate the relationship between membrane material and development of membrane fouling in a membrane bioreactor (MBR) using membranes with different pore sizes and hydrophilicities. Batch filtration tests were performed using submerged single hollow fiber membrane ultrafiltration (UF) modules with different polymeric membrane materials including cellulose acetate (CA), polyethersulfone (PES), and polyvinylidene fluoride (PVDF) with activated sludge taken from a municipal wastewater treatment plant. The three UF hollow fiber membranes were prepared by a non-solvent-induced phase separation method and had similar water permeabilities and pore sizes. The results revealed that transmembrane pressure (TMP) increased more sharply for the hydrophobic PVDF membrane than for the hydrophilic CA membrane in batch filtration tests, even when membranes with similar permeabilities and pore sizes were used. PVDF hollow fiber membranes with smaller pores had greater fouling propensity than those with larger pores. In contrast, CA hollow fiber membranes showed good mitigation of membrane fouling regardless of pore size. The results obtained in this study suggest that the surface hydrophilicity and pore size of UF membranes clearly affect the fouling properties in MBR operation when using activated sludge.

: Microplastics and nanoplastics (MNPs) are becoming an increasingly severe global problem due to their widespread distribution and complex impact on living organisms. Apart from their environmental impact, the effects of MNPs on living organisms have also continued to attract attention. The harmful impact of MNPs has been extensively documented in marine invertebrates and larger marine vertebrates like fish. However, the research on the toxicity of these particles on mammals is still limited, and their possible effects on humans are poorly understood. Considering that MNPs are commonly found in food or food packaging, humans are primarily exposed to them through ingestion. It would be valuable to investigate the potential harmful effects of these particles on gut health. This review focuses on recent research exploring the toxicological impacts of micro- and nanoplastics on the gut, as observed in human cell lines and mammalian models. Available data from various studies indicate that the accumulation of MNPs in mammalian models and human cells may result in adverse consequences, in terms of epithelial toxicity, immune toxicity, and disruption of gut microbiota. The paper also discusses the current research limitations and prospects in this field, aiming to provide a scientific basis and reference for further studies on the toxic mechanisms of micro- and nanoplastics.

Plant cells' ability to withstand abiotic stress is strongly linked to modifications in their mechanical characteristics. Nevertheless, the lack of a workable method for consistently tracking plant cell mechanical properties severely restricts our comprehension of the mechanical alterations in plant cells under stress. With Polyethylene Glycol (PEG6000), we created a drought-like environment, and we used the Double Resonator Piezoelectric Cytometry (DRPC) method to dynamically and non-invasively track changes in the stress (ΔS) created and viscoelasticity (storage modulus G' and loss modulus G") of protoplasts and suspension cells of rice during drought stress. The findings demonstrate that, rice suspension cells and protoplasts react mechanically differently to 5%–15% PEG6000 stress, implying distinct resistance mechanisms. However, neither of them can withstand 25% PEG6000 stress, they respond mechanically similarly to 25% PEG6000 stress. The results of DRPC are further corroborated by the morphological alterations of rice cells and protoplasts observed under an optical microscope. To sum up, the DRPC technique functions as a precise cellular mechanical sensor and offers novel research tools for the evaluation of plant cell adversity and differentiating between the mechanical reactions of cells and protoplasts under abiotic stress.

To better understand the shape memory materials and self-healing materials, a new series of liquid-crystalline shape memory polyurethane (LC-SMPU) composites, named SMPU-OOBAm, were successfully prepared by incorporating 4-octyldecyloxybenzoic acid (OOBA) into the PEG-based SMPU. The effect of OOBA on the structure, morphology and properties has been carefully investigated. The results demonstrate that SMPU-OOBAm have liquid crystalline properties, triple-shape memory properties and self-healing properties. The incorporated OOBA promotes the crystallizability of both soft and hard segments of SMPU, and the crystallization rate of the hard segment of SMPU decreases when the OOBA-content increases. Additionally, the SMPU-OOBAm forms a two-phase separated structure (SMPU phase and OOBA phase), and it shows two-step modulus changes upon heating. Therefore, the SMPU-OOBAm shows triple-shape memory behavior, and the shape recovery ratio decreases with an increase in the OOBA content. Finally, SMPU-OOBAm shows self-healing properties. The new mechanism can be ascribed to the heating-induced “bleeding” of OOBA in the liquid crystalline state and the subsequent re-crystallization upon cooling. This successful combination of liquid crystalline properties, triple-shape memory properties and self-healing properties make the SMPU-OOBAm composites with many promise applications in smart optical devices, smart electronic devices and smart sensors.

The advancement in science and technology has led to luffa sponge (LS) being widely used as a natural material in industrial application as its polyporous structure and light texture. In order to enhance the utility of LS fibers as the reinforcement of lightweight composite materials, this study investigate its water absorption, mechanical properties, anatomical characteristic and thermal performance. Hence, moisture regain, tensile properties of LS fiber bundles were measured in accordance with standards and the structural characteristics were investigated via microscopic observation. Scanning electron microscopy (SEM) was used to observe the surface morphology and fracture surface of fiber bundles. Test results shows that the special structure where the phloem tissues degenerate to cavities had a significant influence on the mechanical properties of LS fiber bundles. Additionally, the transverse sectional area occupied by fibers in a fiber bundle (SF), wall thickness and ratio of wall to lumen of fiber cell, and crystallinity of cellulose had an impact on the mechanical properties of LS fiber bundles. Furthermore, the fiber bundles density of LS varies range of 385.46-468.70 kg/m³, much less than that of jute (1360.40 kg/m³) and Arenga engleri (950.20 kg/m³) while LS fiber bundles has superior specific modulus.

This study investigates the effects of Zinc (4wt.%) and severe plastic deformation on the mechanical properties of AZ61 magnesium alloy through the stir-casting process. The severe plastic deformation (equal channel angular pressing (ECAP)) has been done followed by T4 heat treatment. The microstructural examinations revealed that the addition of 4wt.%Zn enhances the uniform distribution of β-phase, contributing to a more uniformly corroded surface in corrosive environments. Additionally, dynamic recrystallization (DRX) significantly reduces the grain size of as-cast alloys after undergoing ECAP. The attained mechanical properties demonstrate that after a single ECAP pass, AZ61 + 4wt.%Zn alloy exhibits optimal yield strength (YS), ultimate compression strength (UCS), and hardness. This research highlights the promising potential of AZ61 + 4wt.%Zn alloy for enhanced mechanical and corrosion-resistant properties, offering valuable insights for applications in diverse engineering fields.

The influence of short term water absorption on the mechanical properties of halloysite nanotubes-multi layer graphene reinforced polyester hybrid nanocomposites has been investigated. The addition of nano-fillers significantly increased the flexural strength; tensile strength and impact strength in dry and wet conditions. After short term water exposure; the maximum microhardness; tensile; flexural and impact toughness values were observed at 0.1 wt% MLG. The microhardness increased up to 50.3%; tensile strength increased up to 40% and flexural strength increased up to 44%. Compared to dry samples; the fracture toughness and surface roughness of all types of produced nanocomposites were increased that may be attributed to plasticization effect. Scanning electron microscopy revealed that the main failure mechanism is caused by the weakening of nano-filler-matrix interface induced by water absorption. It was further observed that synergistic effects were not effective at concentration of 0.1 wt% to produce considerable improvement in mechanical properties of produced hybrid nanocomposites.

In recent decades, the requirements for implantable medical devices increased, but the risks of implant rejection still exist. These issues are primarily associated with poor osseointegration, leading to biofilm formation on the implant surface. This study focuses on addressing these issues by developing a biomaterial for implant coatings. 45S5 Bioglass has been widely used in tissue engineering due to its ability to form a hydroxyapatite layer, ensuring a strong bond between the hard tissue and the bioglass. In this context, 45S5 bioglasses, modified by the incorporation of different amounts of copper oxide, from 0 to 8 mol%, were synthesized by the melt-quenching technique. The incorporation of Cu ions does not show a significant change in the glass structure. Since the bioglass exhibited the capacity of being polarized, and therefore promoting the osseointegration effectiveness, the electrical properties of the prepared samples were studied using the impedance spectroscopy method, in the frequency range of 102-106 Hz and temperature range of 200-400 K. The effects of CuO on charge transport mobility were investigated. Additionally, the bioactivity of the modified bioglasses was evaluated through immersion tests in simulated body fluid. The results revealed the initiation of a Ca-P-rich layer formation on the surface within 24 h, indicating the potential of the bioglasses to enhance the bone regeneration process.

Abstract. Results of research into four-membered phosphorus(V)-heterocycles, 2-halogen-1,2λ⁵-oxaphosphetanes are presented. The preparation of 2-halo-1,2λ⁵-oxaphosphetanes by reaction of P-haloylides with carbonyl compounds is described. The mechanism of asynchronous [2+2]-сycloaddition of ylides to aldehydes was proposed on the base of low-temperature NMR investigations. 2-Halogen-1,2λ⁵-oxaphosphetanes were isolated as individual compounds and their structures were confirmed by ¹Н, ¹³C, ¹⁹F and ³¹Р NMR spectra. These compounds are convenient reagents for preparing of various organic and organophosphorus compounds hardly available by other methods. Chemical and physical properties of the 2-halo-1,2λ⁵-oxaphosphetanes are reviewed. The 2-chloro-1,2λ⁵-oxaphosphetanes depending on substituents at the α-carbon atom rearrange with formation of 2-chloroalkylphosphonates or convert into trans-phosphorylated alkenes. Prospective synthetic applications of 2-halo-1,2λ⁵-oxaphosphetanes are analyzed. The 2-halo-1,2λ⁵-oxaphosphetanes may be easily converted to various alkenylphosphonates: allyl- or vinylphosphonates, phosphorus ketenes, thioketenes, ketenimines.

Sesamum indicum is considered an underutilized oil-bearing seed in the semi-arid regions of Ghana. Nonetheless, it is a promising source of food with both nutritional and therapeutic benefits. The aim of the present study was to evaluate the antioxidant properties S. indicum seeds using different extraction solvents. The seeds were obtained from the local farmers and prepared for analysis. The bioactive compounds present in the seeds were extracted using hexane, ethyl acetate, ethanol and water and their yields quantified. Total phenolic content (TPC), Condensed tannin content (TTC) and Total antioxidant capacity (TAC) , and DPPH radical scaveging assay were analyzed using standard methods. Antinutrients such as saponins, alkaloids, phytates and oxalates were also analyzed from the powdered seeds. Two chemometric methods; hierarchical cluster analysis (HCA) and Pearson correlation were employed to evaluate the interdependence of the various parameters to result in their antioxidant properties. The re-sults revealed that the solvents utilized had a significant impact on the extraction yield, phyto-chemical component concentration, and antioxidant activities. Hexane extracts of S. indicum seeds significantly exhibited the highest antioxidant activity (p < 0.05). It was marked with the highest TAC value of 232.6 ± 6.267 mg/g AAE and a strong DPPH scavenging activity with an IC50 of 52.81 ± 2.30 µg/mL. Correlations (p < 0.05) was established between TPC,CTC, TAC and DPPH radical scavenging activity) of the extracts. Antinutrients such as; phytate, oxalate, saponins and alkaloids were found to be 7.691 ± 0.8576, 1.501 ± 0.1375, 21.33 ± 4.619 and 317.33 ± 30.29 mg/g respectively. Data obtained suggest that S. indicum possess rich bioactive compounds that can be used in neutraceuticals and food products.

In this study we have investigated the effect of the addition of Nb2O5 (up to 5 mol%) on the structure and luminescent properties of ZnO-B2O3 glass doped with 0.5 mol % Eu2O3 by using of infrared (IR), Raman and photoluminescence (PL) spectroscopy. Physical properties as molar volume, oxygen packing density and glass transition temperature were determined using the results of differential thermal analyisis (DTA) and Archimedes principle for density. IR and Raman spectra revealed that niobium ions incorporate into the base zinc borate glass as NbO4 trtraherda and NbO6 octahedra. A strong red emission from the 5D0 level of Eu3+ ions was registered under near UV (392 nm) excitation using the sharp 7F0 - 5L6 transition of Eu3+. The integrated fluorescence intensity ratio R (5D0 → 7F2/5D0 → 7F1) was calculated to estimate the degree of asymmetry around the active ion, suggesting a location of Eu3+ in non-centrosymmetric sites. The higher Еu3+ luminescence emission observed in zinc borate glasses containing 1÷5 mol% Nb2O5 compared to the Nb2O5-free zinc borate glass evidences that Nb2O5 is suitable component for modification of host glass structure and improving the emission intensity.

Micro-combs [1-4] - optical frequency combs generated by integrated micro-cavity resonators – offer the full potential of their bulk counterparts [5,6], but in an integrated footprint. The discovery of temporal soliton states (DKS – dissipative Kerr solitons) [4,7-11] as a means of mode-locking micro-combs has enabled breakthroughs in many fields including spectroscopy [12,13], microwave photonics [14], frequency synthesis [15], optical ranging [16,17], quantum sources [18,19], metrology [20,21] and more. One of their most promising applications has been optical fibre communications where they have enabled massively parallel ultrahigh capacity multiplexed data transmission [22,23]. Here, by using a new and powerful class of micro-comb called “soliton crystals” [11], we achieve unprecedented data transmission over standard optical fibre using a single integrated chip source. We demonstrate a line rate of 44.2 Terabits per second (Tb/s) using the telecommunications C-band at 1550nm with a spectral efficiency – a critically important performance metric - of 10.4 bits/s/Hz. Soliton crystals exhibit robust and stable generation and operation as well as a high intrinsic efficiency that, together with a low soliton micro-comb spacing of 48.9 GHz enable the use of a very high coherent data modulation format of 64 QAM (quadrature amplitude modulated). We demonstrate error free transmission over 75 km of standard optical fibre in the laboratory as well as in a field trial over an installed metropolitan optical fibre network. These experiments were greatly aided by the ability of the soliton crystals to operate without stabilization or feedback control. This work demonstrates the capability of optical soliton crystal micro-combs to perform in demanding and practical optical communications networks.

To enhance the applicability of dual-phase high-entropy alloys (HEAs) like Fe32Cr33Ni29Al3Ti3, fabricated via selective laser melting (SLM), a focus on improving their mechanical properties is essential. As part of this effort, heat treatment was explored. This study compares the microstructure and mechanical properties of the as-printed sample with those cooled in water after undergoing heat treatment at temperatures ranging from 1000 to 1200 ℃ for 1 hour. Both pre- and post-treatment samples reveal a dual-phase microstructure comprising FCC and BCC phases. Although heat treatment led to a reduction in tensile and yield strength, it significantly increased ductility compared to the as-printed sample. This strength-ductility trade-off is related to changes in grain sizes with ultrafine grains enhancing strength and micron grains optimizing ductility, also the influence of the content of FCC/BCC phases and dislocation density. In particular, the sample heat-treated at 1000 °C for 1 hour and then water-cooled exhibited a better combination of strength and ductility, a yield strength of 790 MPa, and an elongation of 13%. This research offers innovative perspectives on crafting dual-phase HEA of Fe32Cr33Ni29Al3Ti3, allowing for tailorable microstructure and mechanical properties through a synergistic approach involving SLM and heat treatment.

The rock joint fissure slope in cold regions is prone to deformation and failure problems such as relaxation, tension and collapse under freeze-thaw (F-T) cycles. Based on the ideology of clean production and promoting the structural integrity of geotechnical projects in cold areas, this study designed and prepared aeolian-sand (AS) to replace part of river sand as a filling mortar material by taking advantage of the low cost and easy availability of AS. Investigations were carried out to determine the impact of varying proportions of AS in mortar on the microstructure and shear properties of the mortar-rock interface under F-T cycles. Therefore, F-T cycle testing, nuclear magnetic resonance (NMR) testing and shear testing were carried out on grout with different proportions of AS. The results show that the right proportion of AS replacement could enhance the shear deformation resistance and F-T resistance of the mortar-rock interface, and 30% proportion is the optimal proportion. By increasing of F-T cycles, the three types of specimens showed different degrees of particle spalling, shedding and cracking. The slurry-rock interface layer in the A (0%) group exhibited the most severe F-T deterioration, while the B (15%) group showed a lesser degree, and the C (30%) group performed the best. T2 spectrum curve and total spectrum area change law from the microscopic point of view to verify the 30% AS proportion mortar-rock interface F-T resistance is the strongest, followed by 15% AS proportion mortar, the weakest is ordinary mortar. The degradation of the mortar-rock bond is primarily due to the conversion of solid to liquid phases and the movement of internal water caused by fluctuating temperatures. The extent of F-T deterioration in the slurry-rock interface layer is greatly affected by the varying proportions of AS. The shear strength and shear stiffness of specific proportion of AS decreased with the increase of F-T cycles. For same F-T cycles, the shear strength and shear stiffness of group C (30%) were the highest, followed by group B (15%) and group A (0%). The grout material not only reinforces the F-T joint fissure slope, but also reduces the cost of grout reinforcement and promotes the clean production of geotechnical structures.

Microorganisms drive the biogeochemical cycles that link abiotic and biotic processes in the aqueous environment and are intricately associated with plastic debris. The detection of microplastics in water and sediment introduces new concerns as small particle size allows for yet unconsidered pathways for plastics in the food web and element cycles. In this review, we present current knowledge of microbe-plastic interactions and summarize the potential impact of biogeochemical processes on plastic distribution, cycling, transport, and sedimentation. We explore how microbe-plastic interactions influence the exposure of consumers to plastics and plastic degradation products. Key methods used to elucidate biofilm development, microbial biodegradation, and plastic detection in the aqueous environment are discussed. Finally, we comment on potential future questions and research directions needed to further define the role of microorganisms in the environmental fate of microplastics.

In this work the close relation between vorticity and micro-rotation in micropolar flows in Rn (n = 2 or 3) is identified and used to explain the faster decay by t^(-1/2) of the angular velocity of the micro-rotation of fluid particles, as well as establishing its optimality. For this purpose important upper and lower bounds for Leray solutions in homogeneous Sobolev spaces are derived, using the monotonicity approach recently introduced by the authors for dissipative systems in general. Several related results of interest are also given along the discussion.

Chitosan (CS) nanoparticles are under investigation for a wide range of applications in nanomedicine. The structural, molecular and physicochemical properties of chitosan nanoparticles have a direct bearing on their efficacy in drug conjugation and delivery, gene delivery, and tissue engineering. Herein we report on the structural, morphological and molecular properties of chitosan nanoparticles synthesized using the ionic gelation method with the intended purpose of being used for drug delivery. The chitosan nanoparticles (CS-NPs) were prepared in the 0.25 to 1.0% w/v concentration range, whereas separate samples of the 1.0% w/v CS-NPs were also functionalized with polyethylene oxide (PEO) alone and with a diblock copolymer of PEO and polypropylene glycol (PPG). The average size of the CS-NPs was determined from TEM imaging to be in the range of 11.3 to 14.8 nm. The XRD and TEM analyses show that the CS-NPs have semi-crystalline structure with the degree of crystallinity depending upon the nature of synthesis. Our results show that functionalizing the 1.0% w/v CS-NPs with PEO increases the degree of crystallinity whereas functionalizing with the diblock copolymer PEO - PPG results in a significant increase in their degree crystallinity. The CS/TPP concentration (CS:TPP fixed at 1:1 ratio) had no apparent effect on the degree of crystallinity of the CS-NPs. The results from the FTIR analysis confirm incorporation of TPP with CS in the CS-NPs. Additionally, FTIR analysis shows an enhancement of hydrogen bonding that is consistent with the increase in the degree of crystallinity of the CS-NPs.

This study utilises NaOH to treat composite cementitious materials containing aeolian sand and zeolite powders, which were used to replace 50% of the cement in aeolian-sand concrete (ASC). The mechanical properties of treated ASC considerably improved, especially when the NaOH dosage was 4% by mass. After curing this sample (denoted as AAZC-4) for 28 d, its compressive strength improved by 17.2% and its split tensile was increased by 16.3%. Potassium feldspar and montmorillonite in zeolite powder and SiO2 in the sand were decomposed by OH− and combined with other elements to generate various silicate gels and A-type potassium zeolite crystals inside the concrete. Microscopic examination showed that the gels and crystals intertwined to fill the pores, decreasing (increasing) the percentage of large (small) pores, thus optimising the pore structure. This substantially improved the mechanical properties of ASC. Freeze–thaw salt-intrusion tests showed that the extent of mass loss, degree of damage and loss of compressive strength of AAZC-4 were similar to those of ordinary concrete but were reduced by 36.8%, 19% and 52.1%, respectively, compared with those of ASC. Therefore, AAZC-4 has sustainable working performance in the chloride ion permeable environment in cold and arid areas.

The Energy Performance of Buildings Directive 2010 calls for the Nearly Zero Energy Standard for new buildings from 2021 onwards: Buildings using “almost no energy” are powered by renewable sources or energy produced by the building itself. For residential buildings, this ambitious new standard has already been reached. But for other building types this goal is still far away. The potential of these buildings to meet a Nearly Zero Energy Standard was investigated by analyzing ten case studies representing non-residential buildings with different uses. The analysis shows that the primary characteristics common to critical building types are a dense building context with a very high degree of technical installation (such as hospital, research and laboratory buildings). The large primary energy demand of these types of buildings cannot be compensated by building and property-related energy generation including off-site renewables. If the future Nearly Zero Energy Standard were to be defined with lower requirements because of this, the state related properties of Bavaria suggest that the real potential energy savings available in at least 85% of all new buildings would be insufficiently exploited. Therefore, it would be useful to instead individualize the legal energy verification process for new buildings to distinguish critical building types such as laboratories and hospitals.

In the recent years, tubular nanostructures have been related with immense advances in various fields of science and technology. Considerable research efforts have been centered on the theoretical prediction and manufacturing of non-carbon nanotubes (NTs), which meet modern requirements for the developing of novel devices and systems. In this context, diatomic inorganic nanotubes formed by atoms of elements from the 13th group of the periodic table (B, Al, Ga, In, Tl) and nitrogen (N), have received much research attention. In the present work, the elastic properties of single-walled boron nitride, aluminium nitride, gallium nitride, indium nitride and thallium nitride nanotubes were numerically evaluated using the nanoscale continuum modelling approach (also called molecular structural mechanics). The elastic properties (rigidities, surface Young´s and shear moduli, and Poisson´s ratio) of nitride nanotubes are discussed with respect to the bond length of the corresponding diatomic hexagonal lattice. The results obtained contribute to a better understanding of the mechanical response of nitride compound-based nanotubes, covering a broad range from the well-studied boron nitride NTs to the hypothetical thallium nitride NTs.

The carbonyl iron particles were dispersed in a polychloroprene rubber (CR) matrix under an external magnetic field for practical application as microwave absorption composites film. The film prepared under external magnetic field with a thickness of only 0.54 mm showed least reflection loss of -15.98 dB and the reflection loss value less than -10.0 dB over the frequency range of 11.4~14.8 GHz. In comparison with the microwave absorption properties of calculation by transmission line theory based on the tested relative complex permittivity and permeability and film prepared by general route without external magnetic field, the film made with external magnetic field exhibited more excellent microwave absorption properties, strongly depending on the increment of anisotropy and rearrangement of magnetic particles. The results indicated the composite film made under external magnetic field have excellent microwave absorption properties, which suggest that the composites thin film could be used as a thinner and lighter microwave absorber.

Berberis vulgaris (L.) has remarkable ethnopharmacological properties and is widely used in traditional medicine. The present study investigates B. vulgaris stem bark (Berberidis cortex) by extraction with 50% ethanol. The main secondary metabolites were quantified, resulting in a polyphenols content of 17.6780 ± 3.9320 mg Eq Tannic acid / 100 g extract, phenolic acids amount of 3.3886 ± 0.3481 mg Eq Chlorogenic acid / 100 g extract and 78.95 µg/g berberine. The dried hydro-ethanolic extract (BVE) was thoroughly analyzed using Ultra-High Performance Liquid Chromatography coupled with High-Resolution Mass Spectrometry (UHPLC–HRMS/MS) and HPLC and 40 bioactive phenolic constituents were identified. Then, the antioxidant potential of BVE was evaluated using three methods; our results could explain the protective effects of Berberidis cortex EC50FRAP = 0.1398 mg/mL, IC50ABTS = 0.0442 mg/mL, IC50DPPH = 0.2610 mg/mL compared to ascorbic acid (IC50 = 0.0165 mg/mL). Next, the acute toxicity and teratogenicity of BVE and Berberine - Berberine sulfate hydrate (BS) - investigated on Daphnia sp reported significant BS toxicity after 24 h; BVE revealed considerable toxicity after 48 hours and induced embryonic developmental delays. Finally, the anticancer effects of BVE and BS were evaluated on different tumor cell lines after 24 and 48 hours of treatments. The MTS assay evidenced a dose- and time-dependent antiproliferative activity, higher on BS than BVE. The strongest diminution of tumor cell viability was recorded on breast (MDA-MB-231), colon (LoVo) cancer, and OSCC (PE/CA-PJ49) cell lines after 48 h of exposure (IC50 < 100 µg/mL). However, no cytotoxicity was reported on normal epithelial cells (HUVEC) and hepatocellular carcinoma (HT-29) cell lines. Extensive data analysis supports our results, showing a significant correlation between the BVE's concentration, phenolic compounds content, antioxidant activity, exposure time, and the viability rate of various normal cells and cancer cell lines.

The accuracy of cosmic ray observation by the Large High Altitude Air Shower Observatory Wide Field-of-view Cherenkov/fluorescence Telescope Array (LHAASO-WFCTA) is influenced by variations in aerosols in the atmosphere. The solar photometer (CE318-T) is extensively utilized within the Aerosol Robotic Network as a highly precise and reliable instrument for aerosol measurements. With this CE318-T 23, 254 sets of valid data samples in 394 days from October 2020 to October 2022 at the LHAASO site were obtained. Data analysis revealed that the baseline Aerosol Optical Depth (AOD) and A˚ngstro¨m Exponent (AE) at 440-870 nm (AE440−870nm) of the aerosols were calculated to be 0.03 and 1.07, respectively, suggesting that the LHAASO site is among the most pristine regions on Earth. The seasonality of the mean AOD are the order of spring > summer > autumn = winter. The monthly average maximum of AOD440nm occurred in April (0.11 ± 0.05) and the minimum was in December (0.03 ± 0.01). The monthly average of AE440−870nm exhibited slight variations. The seasonal characterization of aerosol types indicated that clean continental background aerosol predominated in autumn and winter, which is the optimal period for the absolute calibration of the WFCTA. Additionally, the diurnal daytime variations of AOD and AE across the four seasons are presented. Our analysis also indicates that the potential origins of aerosol over the LHAASO in four seasons were different and the atmospheric aerosols with higher AOD probably originate mainly from Northern Myanmar and Northeast India region. These results provide a baseline for comparison to the future on-site measurement of extinction coefficient profile and aerosol phase function by LHAASO-WFCTA, also enrich the valuable materials on aerosol observation in the Hengduan Mountains and Tibetan Plateau.

Hierarchical tungsten oxide assemblies such as spindle-like, flowers with sharp petals, nanowires and regular hexagonal structures are successfully synthesized via a solvothermal reduction method by simply adjusting the reaction conditions. On the basis of the experimental results, it is determined that the reaction time significantly influences the phase transition, microstructure and photocatalytic activity of the prepared samples. The possible mechanisms for the phase transition and morphology evolution process have been systematically proposed. Moreover, the as-prepared products exhibit significant morphology-depended photocatalytic activity. The flower-like W18O49 prepared at 6 h possesses large specific surface area (150.1 m²g^-1), improved separation efficiency of electron-hole pairs and decreased electron-transfer resistance by the photoelectrochemical measurements. As a result, the flower-like W₁₈O₄₉ prepared at 6 h exhibits the highest photocatalytic activity for the degradation of Methyl orange aqueous solution. The radical trap experiments showed that the degradation of MO was driven mainly by the participation of h⁺ and •O²⁻ radicals.

Forty-eight Pasteurella multocida isolates were recovered from porcine pneumonic lungs collected in Norwestern Spain (2017- 2019). These isolates were characterized for their minimal inhibition concentrations to twelve antimicrobial agents and for the appearance of eight resistance genes: tetA, tetB, blaROB1, blaTEM, ermA, ermC, mphE and msrE. Relevant resistance percentages were shown to teracyclines, sulphamethoxazole/trimethoprim and tiamulin, thus suggesting that P. multocida isolates were mostly susceptible to amoxicillin, ceftiofur, enrofloxacin, florfenicol, marbofloxacin and macrolides. 29.2% of isolates were resistant to more than two antimicrobials. The tetracycline resistance genes (tetA and tetB) were detected in 22.9% of the isolates, but none was positive to both simultaneously; blaROB1 and blaTEM genes were found in one third of isolates but both genes were detected simultaneously in only one isolate. ermC gene was observed in 41.7% of isolates, a percentage that decreased until 22.9% for msrE; finally, ermA was harboured by 16.7% and mphE was not found in any of them. Six clusters were established based on hierarchical clustering analysis on antimicrobial susceptibility for the twelve antimicrobials. Generally, it was unable to foresee the antimicrobial susceptibility pattern for each family and the association of each particular isolate inside the clusters established from the presence or absence of the resistance genes analyzed.

Energy transition is one of the greatest challenges facing humanity today. All micro, small, medium and large enterprises in operation will have to face it, and some can al-ready boast the first successes in this regard. This paper focuses on the involvement of these smallest players in energy transition. Micro and small entities are the largest part of the economy, having a great influence on its development. Looking at the wide scale of their activities, these entities are distinguished by a specific owner-manager relationship. This means that the final decision-making is influenced by business goals, but also by the manager's approach, their awareness of changes, and personal and other factors. Based on a structured and standardized survey questionnaire, the research was carried out using the Computer-Assisted Telephone Interviewing technique between April and May 2022 among owners of micro and small enterprises operating in Poland. The survey showed that active engagement of micro and small enterprises in energy efficiency initiatives is related to their market success and financial health.

The effects of rare earth Ce on the microstructure and properties of cast pure copper were investigated through thermodynamic calculations, XRD analysis, mechanical testing, metallographic microscopy, and scanning electron microscopy (SEM). The experimental results demonstrate that the reaction between rare earth Ce and oxygen as well as sulfur in copper exhibits a significantly negative Gibbs free energy value, indicating a strong thermodynamic driving force for deoxidation and desulfurization reactions. Ce is capable of removing trace amounts of O and S from copper. Moreover, the maximum solid solubility of Ce in Cu falls within the range of 0.009% to 0.01%. Furthermore, Ce can refine columnar grains while enlarging equiaxed grains in as-cast copper.Upon addition of rare earth Ce, the tensile strength increased by 8.45%, elongation increased by 12.1%, and microhardness rose from 73.5HV to 81.2HV-an increase of 10.5%. Overall, rare earth Ce has been found to enhance both the microstructure and mechanical properties of cast pure copper.

We report a photonic-based radio frequency (RF) arbitrary waveform generator (AWG) using a soliton crystal micro-comb source with a free spectral range (FSR) of 48.9 GHz. The comb source provides over 80 wavelengths, or channels, that we use to successfully achieve arbitrary waveform shapes including square waveforms with a tunable duty ratio ranging from 10% to 90%, sawtooth waveforms with a tunable slope ratio of 0.2 to 1, and a symmetric concave quadratic chirp waveform with an instantaneous frequency of sub GHz. We achieve good agreement between theory and experiment, validating the effectiveness of this approach towards realizing high-performance, broad bandwidth, nearly user-defined RF waveform generation.

The poly lactic acid (PLA) is one of the most used bio-derived thermoplastic polymers in 3D and 4D printing applications. The determination of PLA surface properties is of capital importance in 3D/4D printing technology. (1) Background: The surface thermodynamic properties of PLA polymer were determined by using the inverse gas chromatography (IGC) technique at infinite dilution. The determination of the retention volume of polar and non-polar molecules adsorbed on the PLA particles filling the column allowed us to obtain the dispersive, polar, and Lewis’s acid-base surface properties at different temperatures from 40 °C to 100 °C. (2) Methods: the applied surface method was based on our recent model that used the London dispersion equation and the new chromatographic parameter function of the deformation polarizability and the harmonic mean of the ionization energies of the PLA polymer and organic molecules. (3) Results: The application of this new method led to the determination of the dispersive and polar free surface energy of adsorption of molecules on the polymeric material, as well as the glass transition and the Lewis acid-base constants. (4) Conclusions: four interval temperatures were distinguished showing four zones of the variations of the surface properties of PLA as a function of the temperature before and after the glass transition.

The aim of the present study was to investigate the incidence of breast (females), prostate, testicular and thyroid cancer in the Italian National Priority Contaminated Sites (NPCSs), served by cancer registries, where the presence of endocrine disruptors (EDs), reported to be linked to these tumors, was documented. Evidence of carcinogenicity of EDs present in NPCs was assessed based on evaluation by international scientific institutions/committees. Standardized Incidence Ratios (SIRs) were computed for each NPCS and cancer site with reference to the time window 1996-2005. Excess incidence of one or more cancer site at study was found in twelve out of fourteen NPCSs. Significantly increased SIRs were found for breast cancer in eight NPCSs, for prostate cancer in six, for thyroid cancer (both gender) in four and for testicular cancer in two. Non significantly increased SIRs were found in five NPCSs for testicular cancer and in two for thyroid cancer (males). Even if increased incidence of one or more cancer sites at study were found in several NPCSs, the ecological study design and the multifactorial etiology of the considered tumors do not allow reaching conclusions in terms of causal links with environmental contamination. In light of the observation of some excesses in SIRs, continuing epidemiological surveillance is warranted.

CoCrFeNiMn high-entropy alloy coatings were prepared on compacted graphite iron（CGI） through plasma cladding to strength the CGI substrate. The effects of heat treatment temperatures and times on the microstructure and mechanical properties of the CoCrFeNiMn coatings were investigated. After heat treatment, a single FCC phase was remained in the coating as compared to the deposited one, with smaller dendrites, larger dendritic spacing and more Cr-rich compounds precipitated between dendrites. The coatings’ microhardness was increased after heat treatment. After heat treated at 660°C for 90 minutes, the coating had the highest microhardness of 563±6.9 HV0.2, the lowest frictional coefficient of 0.71 and the smallest wear mass loss of 1.12 mg, and it had the best wear resistance.

Soil organic matter (SOM) is important for the global carbon cycle, and hyperspectral remote sensing has proven a promising method for fast SOM content estimation. However, soil physical properties significantly affect the sensitivity of satellite hyperspectral imaging to SOM, leading to poor generalization ability of the estimation model. This study aims to improve the spatiotemporal transferability of the SOM prediction model by alleviating the coupling effect of soil physical properties on the spectra. Based on satellite hyperspectral images and soil physical variables, including soil moisture (SM), soil surface roughness (root mean squared height, RMSH), and soil bulk weight (SBW), a soil spectral correction strategy was established based on the information unmixing method. Two important grain-producing areas in Northeast China were selected as study areas to verify the performance and transferability of the spectral correction model and SOM content prediction model. The results showed that soil spectral corrections based on fourth-order polynomials and the XG-Boost algorithm had excellent accuracy and generalization ability, with residual predictive deviations (RPD) exceeding 1.4 in almost all bands. In addition, when the soil spectral correction strategy was adopted, the accuracy of the SOM prediction model and the generalization ability after model migration were significantly improved. The SOM prediction accuracy based on the XG-Boost corrected spectrum was the highest, with a coefficient of determination (R2) of 0.76, root mean square error (RMSE) of 5.74 g/kg, and RPD of 1.68. The prediction accuracy, R2, RMSE, and RPD of the model after migration were 0.72, 6.71 g/kg, and 1.53, respectively. Compared with the direct migration prediction of the model, adopting the soil spectral correction strategy based on fourth-order polynomials and XG-Boost reduced the RMSE of the SOM prediction results by 57.90% and 60.27%, respectively. The performance comparison highlighted the advantages of considering soil physical properties in regional-scale SOM prediction.

Organic fertilizer application in agricultural land is known to improve soil microbial processes, fertility, and yield. In particular, stable changes in soil chemical composition through multi-year fertilization of organic fertilizers are thought to cause changes in the microbial community. Here, the effects of oil cake amendments (OC) on soil bacterial diversity, community profile and enzyme activity were evaluated and compared to those amended with chemical fertilizer (NPK). The comparison of diversity indices between OC and NPK amended soils shows that application of oil cake has increased microbial diversity potentially with an increase in the number of different microbial groups. The ordination plot distinguished and clustered both treatments showing differential effects of soils chemical factors on the microbial communities of each treatment. Proteobacteria, Verrucomicrobia and Bacteriodetes were significantly abundant in OC amended soil than in the NPK received soil, indicating alterations in community structure, composition, and diversity con-current to the changes in pH, Ca and Mg contents of the soil. These shifts in bacterial community structure and composition could also be observed from the phylum to the genus level in both NPK and OC amended soils partially explained by differences in soil chemical factors. The OC soil compared to the NPK amended soil also contain significantly higher abundance of predicted genes corresponding to enzymes related to biogeochemical cycling, decomposition and plant growth promotion. Collectively, these results support the use of an unconventional organic fertilizer positively altering bacterial populations in jujube orchards. The application of oil cake-based organic fertilizer improved microbial diversity and enhanced potential ecosystem functions related to bio-geochemical cycles, mineralization and plant growth promotion.

Micro/Nano Robot is an intelligent and efficient microrobot that can perform specific tasks under the influence of external stimuli. Depending on the application scenarios, the microrobot can adaptively transform into appropriate functional forms under different external stimuli, thus perfectly matching the needs. To date, microbots have been widely used in targeted therapy, drug delivery, tissue engineering, environmental remediation, and other fields. Although the applications of microrobots are promising, there are only a few reviews that can focus on the preparation methods and driving mechanisms. Therefore, it is necessary to outline the current status of the development of these microrobots in order to provide some new insights for the further development of the field. Therefore, this paper reviews the research progress of microrobots in terms of preparation methods, stimulus response mechanisms and applications, and highlights the applicability of different preparation methods and stimulus types. Finally, the current challenges faced by microrobots are highlighted and possible solutions are proposed to facilitate the practical application of microrobots.

When describing the tribological behaviour of technical surfaces, the need for full length scale microtopographic characterization often arises. The self-affine of surfaces and the characterization of self-affine by a fractal dimension and its implantation into tribological models are commonly used. The goal of our present work was to determine the frequency range of fractal behaviour of surfaces by analysing the microtopographic measurements of a brake plunger. We also wanted to know if the bifractal and multifractal behaviour can be detected in real machine parts. As a result, we developed a new methodology for determining the fractal range boundaries to separate the nano- and micro-roughness. In order to reach our goals, we used atomic force microscope (AFM) and stylus instrument to provide measurements in wide frequency range (19 nm - 3 mm). As a result of the power spectral density (PSD) based fractal evaluation, it was found that the examined surface could not be characterized by a single fractal dimension and that we developed a methodology for stopping the margin of validity of each fractal dimension, and we also developed a methodology for determining the limits of validity of certain fractal dimensions.

A micro decision-making utility model under uncertainty is presented as a complementary foundation for macro coronavirus models. The micro model consists of two functions, a risk averse utility function depending on wellness and a wellness random output which is a function of the input variable called “treatment” consisting of such elements as social distance, washing hands, wearing a face mask, and others. The decision maker selects a level of treatment that maximizes her/his expected utility, given the probabilities of the respective outputs. The focus is on how changes in a person’s psychological attitude towards the macro determined (announced) probabilities affects the optimum results of the model. Such changes create a micro-macro dynamic interaction which is briefly outlined. A short discussion of the model’s behavioral implications for health policy is also given.

The alcoholic fermentation process with agitation/static, followed by the acetic fermentation submerged in banana was evaluated. Kinetics parameters of alcoholic fermentation for the maximum ethanol/glycerol metabolites in agitated process was 29 and 27 h, and in static 47 and 45 h, respectively. For acetic fermentation, the kinetics parameters were medium time of 39.9 h, acetic acid yield of 53.1% and acetic acid productivity of 0.216 g/Lh. Wines from agitated/static process presented 5.73 and 6.81% (v/v) of alcohol content, respectively. Wine obtained by the static process presented higher concentrations of volatile compounds. The vinegar showed 49.2 g/L of acetic acid and the esters concentrations were higher than in wine. The wine and vinegar minerals were consistent with amount observed in the pulp, with an increase in sulphur concentration after alcoholic fermentation and decrease after acetic fermentation. Products showed chemical and composition of sensory and nutritional interest.

In this study, 10%PTFE/PEEK blend were modified by potassium titanate whisker (PTW) and chopped glass fiber (GF), respectively. The blends were prepared by three-screw extruder. Through the investigation of thermal stability, tribological properties, mechanical properties and rheological behavior, the effects of reinforcing agents were determined. The results illustrated that the mechanical properties of 10%PTFE/PEEK blend can be dramatically improved by adding reinforcing agent of PTW or GF, and the reinforcing effect of GF was especially obvious. As for tribological properties, 1% addition was the best proportion. The friction coefficient and wear rate of the blend with 1% PTW were 0.283 and 4.97 × 10^-6 mm³/N · m, which decreased by 7.2% and 21% compared with those of the blend without reinforcing agent.

This work investigated the isothermal holding time dependence of the densification, microstructure, weight loss and tensile properties of Fe-Mn-Si powder compacts. Elemental Fe, Mn and Si powder mixtures with a nominal composition of Fe-28Mn-3Si (in weight percent) were ball milled for 5h and subsequently pressed under a uniaxial pressure of 400 MPa. The compacted Fe-Mn-Si powder mixtures were sintered at 1200 ℃ for 0, 1, 2 and 3 h, respectively. In general, the density, weight loss and tensile properties increased with the increase of isothermal holding time. A significant increase in density, weight loss and tensile properties occurred in the compacts isothermally holding for 1 h, as compared to those with no isothermal holding. However, further extension of isothermal holding time (2 and 3 h) only played a limited role in promoting the density and tensile properties. The weight loss of the sintered compacts was mianly caused by the sublimation of Mn in Mn depletion region on the surface layer of the sintered Fe-Mn-Si compacts. The length of the Mn depletion region increased as isothermal holding time increased. A single α-Fe phase was detected on the surface of all the sintered compacts, and the locations beyond the Mn depletion region were comprised of a dual dominant γ-austenite and minor ε-martensite.

In this study, a new type of temperature sensor device was developed. The circular electrode of the thermal sensitive sensor was modified with TMT and O₂ plasma to enhance the conductivity by forming a thin SnOxCy layer on the electrode surface. The Nano-Au particles were subjected to O₂ plasma pretreatment to form peroxide groups on the surface. The thermally sensitive sensor was made by mixing the above-treated Nano-Au particles with N-isopropylacrylamide (NIPAAm) to form solution and then UV-induced grafting polymerization of the NIPAAm-containing solution onto the electrode substrate. The composite hydrogels on the electrode introduce thermo-sensitive polymeric surface films for temperature sensing. Using ambient environment resistance test to measure the resistance, the LCST (lower critical solution temperature) of Nano-Au (MUA) mixed with NIPAAm hydrogel was found to be 32 °C. At ambient temperatures higher than LCST, the electrode resistance decreases linearly.

Scientific studies on the impact of wood species on solid fuel production, performance, and sustainability are grossly inadequate. The knowledge of this is imperative as users of solid fuels are increasing rapidly, especially in Africa. On this note, it becomes necessary to explore measures that will improve its efficiency and sustainability as an energy source. This study investigates some properties of selected wood species used as an energy source in Nigeria and their pelleting potential. Nine (9) samples were characterized and assessed for suitability of pelleting following four wood pellet quality standards. The findings revealed Anogeissus leiocarpus as the species with the best rating score in terms of fuel properties while Vitellaria paradoxa as the lowest. However, in terms of conformity with the four wood pellets standards, Khaya senegalensis, Parkia biglobosa and Anogeissus leiocarpus having presented density, calorific value, sulfur, arsenic, cadmium, and lead within the limits of the wood pellet quality standards were considered the best wood species in terms of fuel suitability and pelleting potential. The findings therefore suggest that not all wood species are suitable as fuel. Thus, for species that do not meet the standard wood pellet requirements, alternatives such as the use of biomass blends, additives, or process adjustments can be employed to adapt the quality to the standards or by using the fuels in improved cookstoves.

Synchrotron radiation computed tomography (SRCT) allows more accurate calcified plaque and coronary stenosis assessment as a result of its superior spatial resolution, however, typical micro-computed tomography (micro-CT) systems have even higher resolution. The purpose of this study was to compare performance of high-resolution micro-CT with SRCT in the assessment of calcified plaques and a previously published dataset of coronary stenosis assessment. This experimental study involved micro-CT scanning of three-dimensional printed coronary artery models with calcification in situ used in our previously published SRCT study on coronary stenosis assessment. Measurements of coronary stenosis utilizing both modalities were compared using a paired sample t-test. The degrees of stenosis measured on all but one micro-CT dataset were statistically significantly lower than the corresponding SRCT measurements reported in our previous paper (p<0.0005-0.05). This indicates that the superior spatial resolution of micro-CT was able to further reduce over-estimation of stenosis caused by extensive calcification of coronary arteries and hence false positive results. This study shows that high-resolution micro-CT outperforms SRCT in both calcified plaque and coronary stenosis assessment. This finding will become clinically important for cardiovascular event prediction and enable reclassification of individuals with low and intermediate risk into appropriate risk categories when the technical challenges of micro-CT in clinical practice such as the small field of view and demanding on image processing power are addressed.

Bimetallic Ni/Cu core-shell and Cu-Ni heterostructural micro- and nanoparticles were prepared using two simple successive reduction procedures. Monometallic Ni and Cu particles were synthesized for comparison. The phase constitutions and morphological features of the particles were studied by means of X-ray diffraction, energy-dispersive X-ray spectroscopy and scanning electron microscopy methods. All the obtained mono- and bimetallic particles were applied as electrocatalysts in the electrohydrogenation of p-nitrophenol (p-NPh). An additional electrochemical reduction of copper cations during the hydrogen saturation of Cu-containing particles was established. Some of the prepared particles exhibited high catalytic activity with an increase in the hydrogenation rate of p-NPh by more than 3 times compared to its electrochemical reduction on the non-activated cathode, and p-NPh conversion yielded the maximum values. The main product of p-NPh electrocatalytic hydrogenation over Ni-Cu particles is p-aminophenol, which is an intermediate in the synthesis of many drugs. p-Aminophenol formation is confirmed by UV-Vis spectra.

The effects of CO₂-water-rock interactions on the mechanical properties of shale are essential for estimating the possibility of sequestrating CO₂ in shale reservoirs. In this study, uniaxial compressive strength (UCS) tests together with an acoustic emission (AE) system and SEM & EDS analysis were performed to investigate the mechanical properties and microstructural changes of black shales with different saturation times (10 days, 20 days and 30 days) in water dissoluted with sub-/super-critical CO₂. According to the experimental results, the values of UCS, Young’s modulus and brittleness index decrease gradually with increasing saturation time in water with sub-/super-critical CO₂. Compared to intact samples, 30-days’ saturation causes reductions of 56.43% in UCS and 54.21% in Young’s modulus for sub-critical saturated samples, and 66.05% in UCS and 56.32% in Young’s modulus for super-critical saturated samples, respectively. The brittleness index also decreases drastically from 84.3% for intact samples to 50.9% for samples saturated in water with sub-critical CO₂, to 47.9% for samples saturated in water with super-critical carbon dioxide (SC-CO₂). SC-CO₂ causes a greater reduction of shale’s mechanical properties. The crack propagation results obtained from the AE system show that longer saturation time produces higher peak cumulative AE energy. SEM images show that many pores occur when shale samples are saturated in water with sub-/super-critical CO₂. The EDS results show that CO₂-water-rock interactions increase the percentages of C and Fe and decrease the percentages of Al and K on the surface of saturated samples when compared to intact samples.

Preventing the occurrence of secondary caries serves as one of the significant issues in dental clinic, thus make it indispensable to improving the properties of conventional composite resin (CR) by developing a novel CR. In present study, two groups of experimental CRs loaded with different contents of fluoride-doped nano-zirconia fillers (25 wt% and 50 wt%) were fabricated. The surface topography, mechanical performance, fluoride release, antibacterial effect, aging property and cytotoxicity of the experimental CRs were evaluated subsequently. A uniform distribution of the F-zirconia fillers over the whole surface of resin matrix could be observed. The experimental CRs showed continuous fluoride release within 28 days, which was positively correlated with the content of F-zirconia fillers. Moreover, the amount of fluoride release increased in the acidic buffer. Addition of F-zirconia fillers could improve the color stability, wear resistance and microhardness of the experimental CRs, without reducing the flexure strength. Furtherly, the fluoride ions released continuously from the experimental CRs resulted in effective contact and antibacterial properties, while they showed no cytotoxicity. As a consequence, considerations can be made to employ this new kind of composite resin loaded with fluoride-doped nano-zirconia fillers to meet clinical requirements when the antimicrobial benefits are desired.

There is an important complementarity between experimental methods for the study of high-temperature viscoelasticity in the time and frequency domains, that has not always been fully exploited. Here we show that parallel processing of forced-oscillation data and microcreep records, involving consistent use of either Andrade or extended Burgers creep-function models, yields a robust composite modulus-dissipation dataset spanning a broader range of periods than either technique alone. In fitting this dataset, the alternative Andrade and extended Burgers models differ in their partitioning of strain between the anelastic and viscous contributions. The extended Burgers model is preferred because it involves a finite range of anelastic relaxation times, and accordingly a well-defined anelastic relaxation strength. The new strategy offers the prospect of better constraining the transition between transient and steady-state creep, or equivalently, between anelastic and viscous behaviour.

This article develops algorithms for the characterization and the visualization of micro-scale features by using a small number of sample points, and with a goal to mitigate for the measurement shortcomings which are often destructive or time consuming. We implement the algorithms to rapidly examine the microscopic features of a Microelectromechanical System (MEMS) surface. Such images are highly dense; therefore, traditional image processing techniques might be computationally expensive. The contribution of this research include first, we develop local and global algorithm based on modified Thin Plate Spline (TPS) model to reconstruct high resolution images of the micro-surface’s topography, and its derivatives by using low resolution images. Second, we obtain a bending energy algorithm from our modified TPS model, and use it to filter out image defects. Finally, we develop a computationally efficient Windowing technique, which combines TPS and Linear Sequential Estimation (LSE), to enhance the visualization of images. The Windowing technique allows rapid image reconstruction based on the reduction of inverse problem.

Aluminum wire is a common material for wire bonding due to its resistance to oxidation and low price. It does not melt when becoming a free air ball (FAB) during the electronic flame-off (EFO) process with wettability, and is applied by wedge bonding. This study used 20μm Zn-Coated Al-0.5wt.%Si (ZAS) wires to improve the FAB shape after the EFO process, while maintaining stability of the mechanical properties, including the interface bonding strength and hardness. In order to test circuit stability after ball bonding, the current-tensile test was performed. During the experiment, it was found that 80nm ZAS with wire bonding has lower resistance and higher fusing current. For the bias tensile test, the thicker Zn film diffused into the Al-Si matrix easily, after which the strength was reduced. The ball-bond interfaces had no change in their condition before and after the bias. Accordingly, ZAS could be a promising candidate for ball bonding in the future.

The paper discusses the mechanism of montmorillonite structure alteration and bentonites properties modification (on the example of samples from clay deposit Taganka, Kazakhstan) due to the thermochemical treatment (treatment with inorganic acid solutions at different temperatures, concentrations and reaction times). With the use of the suit of methods certain processes were distinguished: transformation of montmorillonite structure, which appears in the leaching of interlayer and octahedral cations, protonation of the interlayer and OH groups at octahedral sheets. Changes in the structure of the 2:1 layer of montmorillonite and its interlayer result in significant changes in the properties – reduction of cation exchange capacity and an increase of specific surface area. The results of the work showed that bentonite clays retain a significant portion of its adsorption properties even after the long term and intense thermochemical treatment (6M HNO3, 60°C, 108 hours)

Practical applications of CsPbX3 nanocrystals (NCs) are limited by their poor stability. The formation of heterojunction between CsPbX3 NCs and oxides is an effective means to protect perovskite from polar solvents and other external factors. Significantly improving the stability and photocatalytic properties of the core/shell perovskite is very important for its application in photoelectric and photocatalytic technology. Here, we report the synthesis of asymmetrical CsPbBr3/TiO2 core-shell heterostructure NCs at single particle level by hot injection liquid phase synthesis and sol-gel method, where each CsPbBr3 NCs is partially covered by titanium dioxide. It is shown that the type II arrangement is generated at the heterogeneous interface, which greatly facilitates the separation of electron-hole pairs and increases the carrier transport efficiency. More crucial, due to the protection of titanium dioxide shell, the product has higher long-term stability in humid air compared with bare CsPbBr3 NCs. The asymmetrical core-shell heterostructure prepared in this study not only improves the stability of CsPbX3 NCs, but also provides some ideas for optoelectronic device applications and TiO2-based photocatalysts.

There is a need for alternatives or complements to synthetic fertilizers to enhance agricultural sustainability. Applying organic amendments can play a significant role in this. Insect droppings show high potential, though studies evaluating their agronomic value have only recently begun to emerge. This study compared black soldier fly (Hermetia illucens) and mealworm (Tenebrio molitor) larvae frass with another organic amendment (Nutrimais) derived from composting forestry, agro-industrial, and domestic waste. The experiment also included ammonium nitrate at two rates [the same as the organic amendments, 50 kg ha–1 nitrogen (N) (FullR), and half that rate (HalfR)] and an unfertilized control. The study spanned two growth cycles of lettuce (Lactuca sativa L.) grown in pots, followed by unfertilized oats (Avena sativa L.) to assess the residual effects of the fertilizing treatments. Mealworm larvae frass mineralized rapidly, with an apparent N recovery of 37.4% over the two lettuce growth cycles, indicating its high availability to soil heterotrophic microorganisms. The average dry matter yield (DMY) of lettuce was the highest among all treatments (12.8 and 9.8 g plant–1 in the first and second lettuce cycles), even compared to the FullR treatment (12.2 and 7.8 g plant–1), though without significant differences. Although mealworm larvae frass exhibited a high mineralization rate, the DMY cannot be attributed solely to N supply, as plants in the FullR treatment showed better N nutritional status. Mealworm larvae frass provided strong evidence of a plant biostimulant effect, not explained by the variables measured in this study. Black soldier fly larvae frass exhibited typical behavior of a moderately reactive organic amendment, while Nutrimais showed low reactivity, with a near-neutral mineralization/immobilization balance. The results suggest mealworm larvae frass is recommended for early maturing vegetable crops, whereas Nutrimais appears more suitable for perennial crops with low short-term nutrient requirements.

GaN-based micro-size light-emitting diodes (µLEDs) have a number of appealing and distinctive benefits for display, visible-light communication (VLC), and other novel applications. The smaller size of LEDs affords them the benefits of enhanced current expansion, less self-heating effects, and higher current density bearing capacity. Low external quantum efficiency (EQE) resulting from non-radiative recombination and quantum confined stark effect (QCSE) is the serious barrier for applications of µLEDs. In this work, the reasons for the poor EQE of µLEDs are reviewed, as well as the optimization techniques for improving the EQE of µLEDs.

This research paper is part of the wider project concerning the very first detailed mapping of the overall Taiwanese hydro-power plants that took place from 2013 up to 2015 and it is currently in evaluation and finalization stage. The case of Shanping hydro-power plant has been carefully studied, photographed, documented and mapped in situ. It was one of the isolated hydro-power plant projects originally built to supply the remote area with the specific designation. Shanping hydro-power plant, as well as the other units from the early hydro-power generation era in Taiwan, are considered to be the technological heritage of civil and mechanical engineering that reflects later in all the further projects up to nowadays modern Taiwanese hydro-power plants. Unfortunately, most of the hydro-power houses from the older periods were severely damaged or destroyed by natural causes which were also the case of Shanping unit. The research is trying to reconstruct the original location of the powerhouse and its supporting structures based on available historical documents, previous studies, comparative methodology, and the current on-site observation.

To improve efficacy and safety of sunscreen emulsions, UV‐filter skin permeation could be kept as low as possible by reducing UV‐filter content or changing emulsion composition. In this work, different lipid phase ratio (12, 14 and 16% w/w) were assessed for their ability to affect the technological and sensory properties of O/W emulsions in which bemotrizinol (BMTZ), a broad spectrum sunscreen agent, was incorporated free or loaded into nanostructured lipid nanocarriers (NLC) to reduce its release from the vehicle and, hence, its skin permeation. The following technological properties were evaluated in vitro by suitable methodologies: spreadability, viscosity, pH, occlusion factor, BMTZ release, sun protection factor (SPF). Sensory attributes were assessed by trained panelists in three different phases: before/during pick‐up, rub‐in, after application. Raising the lipid phase ratio led to an increase of viscosity and to a corresponding drop of spreadability while the incorporation of BMTZ‐loaded NLC determined a decrease of occlusion factor and an increase of SPF. No BMTZ release was observed from all emulsions. Sensory attributes were mainly affected by lipid phase ratio. These results suggest that lipid phase ratio and BMTZ incorporation into NLC could contribute to determine technological and sensory properties of O/W emulsions.

Opuntia ficus-indica (L.) Mill. belongs to the Cactaceae family and the genus Opuntia; it is a succulent plant that adapts to extreme climatic conditions. The aerial part of the plant consists of the cladodes, morphological changes of branches that appear green, are covered with thorns, and are essential to reduce excessive perspiration of water. The composition of cladodes is very varied, and the main constituents are water, fibers, polysaccharides, proteins, fatty acids, vitamins, sterols, minerals, and polyphenols. Polyphenols are responsible for many beneficial activities for human health, such as antioxidant, anti-inflammatory, antitumor, and nutritional properties. The purpose of this manuscript was to compare the properties of cladodes belonging to the same plant but with different stages of maturity. Relative extracts were tested both in vitro and on a cell line and antioxidant and anti-apoptotic properties were found. The antioxidant activity was tested by the ORAC test, the DPPH test, and the measurement of cellular accumulation of ROS. Anti-apoptotic activity was evaluated by the annexin/PI assay and measurement of caspases 9 and 3 expression. The results obtained have shown that the extracts considered possess antioxidant and anti-apoptotic properties. However, the different stages of maturity of cladodes are essential for the performance of both functions. In addition, important variations have been made in the dissolution of extracts that have brought greater safety in their use. In conclusion, this manuscript provides further information on cladodes of Opuntia ficus-indica, which can be used as adjuvants in many human pathologies.

Micro-gyroscopes based on the Coriolis principle are widely employed in inertial navigation, motion control, and vibration analysis applications. This paper presents our main contributions which include a novel dual-frame optomechanical gyroscope, a unique photonic crystal cavity design, and advanced numerical simulation and optimization methods. The proposed design utilizes an optical cavity formed between dual oscillating frames, whereby input rotation induces a measurable phase shift via optomechanical coupling. Actuation of the frames is achieved electrostatically via an interdigitated comb-drive design. Through theoretical modeling based on cavity optomechanics and finite element simulation, the operating principle and performance parameters are evaluated in detail. Results indicate an expected angular rate sensitivity of 22.8 mV/°/s and angle random walk of 7.1×10-5 °/h1/2, representing superior precision than to existing micro-electromechanical systems gyroscopes of comparable scale. Detailed analysis of the optomechanical transduction mechanism suggests this dual-frame approach could enable angular vibration detection with resolution exceeding state-of-the-art solutions.

This paper is regarding design and program an Micro-controller Arduino Uno board by using Arduino software to work as a photo-sensor(Active) single axial solar tracker system(SASTS). A solar panel, two photo-resistors (LDR) in two sides (north/south) of the photo-voltaic(PV) and a servo motor are connected to the Uno board, which is running a code that prepared by Arduino software IDE in advanced then it works as a tracking system. Here, the LDRs send the signal of presence or absence of the light to the board and based on that sent signal the Uno reflects a new signal to the servo motor to rotate and finds the light source. Lastly, the photo-sensor single axis tracker is made while Continuously, the system tries to face the panel to the sun and whilst changing the irradiance intensity it starts searching to find the angle of highest irradiance. Based on results that are extracted from the data, the tracker system significantly boosts the output efficiency of the solar panel. By using the Micro-controller Uno board, LDRs, servo motor and special designed mechanical base, the tracking system is constructed, based on acquired data the influence of the STS on the increasing the solar panel efficiency is more obvious. Significantly, the tracker system rises the efficiency of the PV .

The present overview of spin-dependent phenomena in nonmagnetic semiconductor microparticles (MPs) and nanoparticles (NPs) with interacting nuclear and electron spins is aimed at covering a gap between the basic properties of spin behavior in solid-state systems and a tremendous growth of the experimental results on biomedical applications of those particles. The first part of the review represents modern achievements of spin-dependent phenomena in the bulk semiconductors from the theory of optical spin orientation under indirect optical injection of carriers and spins in the bulk crystalline silicon (c-Si) – via numerous insightful findings in the realm of characterization and control through the spin polarization – to the design and verification of nuclear spin hyperpolarization in semiconductor MPs and NPs for magnetic resonance imaging (MRI) diagnostics. The second part of the review is focused on the electron spin-dependent phenomena in Si-based nanostructures, including the photosensitized generation of singlet oxygen in porous Si and design of Si NPs with unpaired electron spins as prospective contrast agents in MRI. The experimental results are analyzed by considering both the quantum mechanical approach and several phenomenological models for the spin behavior in semiconductor/molecular systems. Advancements and perspectives of the biomedical applications of spin-dependent properties of Si NPs for diagnostics and therapy of cancer are discussed.

Many research work has demonstrated that taken the Combined Cooling Heating and Power system (CCHP) as the core equipment, the integrated energy system (IES) can bring obvious benefit to energy efficiency, CO2 emission reduction and operation economy in urban areas. Compared with isolated IES, integrated energy micro-grid (IEMG) which is formed by connecting multiple regions IES together, through distribution and thermal network, can further improve the reliability, flexibility, cleanliness and economy of regional energy supply. Based on the existing IES model, this paper describes the basic structure of IEMG and built a IEMG planning model. The planning based on the mixed integer linear programming, and economically construction planning scheme are calculated by using known electricity, heating and cooling loads information and the given multiple equipment selection schemes. At last, the model is validated by a case study. The results show that the application of IEMG can effectively improve the economy of regional energy supply.

In the fifth generation communication system, millimeter wave (mmWave) networks will coexist with traditional micro wave (μWave) networks, which allows for higher data transmission rate and better user experience. In this paper, we give a comprehensive framework of mathematical models and analytical methods for multi-tier mmWave and μWave hybrid caching networks based on stochastic geometry. We propose an association strategy by assuming average biased-received power association and Rayleigh fading. Accordingly, by using a D-ball approximating blockage model of mmWave networks, expressions of the cell association probability and the coverage probability of the hybrid networks are derived. Also, we use the average successful delivery probability as the performance metric to analyze the existing caching placement strategies. Simulation results validate the accuracy of our analytical conclusions.

Micro nano bubbles (MNBs) can generate ·OH in situ, which provides a new idea for the safe and efficient removal of pollutants in water supply systems. However, the difficulty in obtaining stable MNBs causes the low efficiency of ·OH generation, which makes the inability to guarantee the removal efficiency of pollutants. This paper reviews the application research of MNBs technology in water security from three aspects: the generation process of MNBs in water, the generation rule of ·OH during MNBs collapse, and the control mechanism of MNBs on pollutants and biofilms. We found that MNBs generation methods are divided into chemical and mechanical (about 10 kinds) categories, and the instability of bubble size restricts the application of MNBs technology. The generation of ·OH by MNBs is affected by pH, gas source, bubble size, temperature, external stimulation. And pH and external stimulus have more influence on ·OH generation in situ than other factors. Adjusting pH to alkaline or acidic conditions and selecting ozone or oxygen as the gas source can promote the ·OH generation. MNBs’ collapse also releases a large amount of energy, which the temperature and pressure can reach 3000K and 5Gpa respectively, making it efficient to remove ≈90 % of pollutants (i.e., trichloroethylene, benzene, and chlorobenzene). The biofilm can also be removed by physical, chemical, and thermal effect. MNBs technology also has great application potential in drinking water, which can be applied to improve water quality, optimize household water purifiers, and enhance the taste of bottled water. Under the premise of safety, let people of different ages taste, finding that compared with ordinary drinking water, 85.7 % of people think MNBs water is softer, 73.3 % of people think MNBs water is sweeter. This further proves that MNBs water has a great prospect in the drinking water application. This review provides innovative theoretical support for solving the problem of drinking water safety.

Abstract. Graphene family (GF)-Calcium phosphate (CaP) composites, holds great potential as components of bone regeneration materials. GF nanomaterials can be modified physically as well as chemically, which are to be biomimetic, mechanically to be hard due to their capability to support exceptional mechanical, thermal and electronic properties. These biocompatible GF composites coated on the calcium phosphate can enhance and tolerate stem cell growth and differentiation, proliferation into various lineages or interact with bioorganisms. The development in CF-CaP materials and their physicochemical/biointeractions and strategies towards osteoblasts is a great concern to promote faster healing and reconstructions of large bone imperfections or defects. In this review, we explain the influence of the CF-CaP and summarize recent developments on designing CF-CaP architectures as multifunctional bone regeneration platforms. We have also explored the typical biological applications concerning these CF-CaP based bioactive nanocomposites. Furthermore, the future viewpoints and evolving challenges will also be emphasized. Due to the shortage of full-length reviews in this emerging research field, this review would be caught great attention and encourage various new chances across a wider range of disciplines.

Wide bandgap semiconductors-based photocatalysts are usually limited by their low solar energy conversion efficiency due to their limited absorption solar wavelength, surface’s fast recombination of photoelectron–hole pairs and low charge-carrier mobility. Here we report a new stepwise solution synthesis for making a new photocatalytic core/shell of titanate nanowire/reduced graphene oxide shell (or titanate/rGO) 1D-nanocomposite. The new core/shell nanocomposite maximized the specific surface area, largely reduced the charge transfer resistance and reaction energy barrier, and significantly improved the absorption of the visible light. The core/shell nanocomposites’ large on/off current ratio and rapid photo-responses boosted the photocurrent by 30.0%, the photocatalysis rate by 50.0%, and the specific surface area by 16.4%, when comparing with the pure titanate nanowire core. Our numerical simulations support the effective charge separation on the new core-shell nanostructure, which can help further advance the new photocatalysis.

The beneficial effects of Lanthanide incorporation into 0.94Na0.5Bi0.5TiO3-0.06BaTiO3 (BNT-BT) matrix on its functional properties were investigated. The conventional solid-state method was used for synthesizing samples. The structural refinement revealed that all samples crystallized in R3c rhombohedral symmetry. Raman spectroscopy study was carried out using green laser excitation and revealed that no clear perceptible variation in frequency is observed. Dielectric measurements unveiled that the introduction of rare earth obstructed the depolarization temperature promoted in BNT-BT with decreasing the diffusive phase transition with increasing the lanthanide size. Only Dysprosium addition showed comparable diffusion constant and dielectric behavior as the unmodified composition. Further, the comparison of the obtained ferroelectric hysteresis and strain-electric field loops revealed that only Dy-phase exhibited interesting properties comparing parent composition. In addition, the incorporation of lanthanides Ln3+ into the BNT-BT matrix led to the development of luminescence characteristics in the visible and near infrared regions, depending on the excitation wavelengths. The simultaneous occurrence of photoluminescence and ferroelectric/piezoelectric properties opens up possibilities for BNT-BT-Ln to exhibit multifunctionality in a wide range of applications.Keywords: Sodium Bismuth Titanate; structural refinement; dielectric properties; ferroelectric properties; piezoelectric properties; Photoluminescence.

Modeling the flow of polymer solutions requires knowledge at various length and time scales. The macroscopic behavior is described by the overall velocity, pressure and stress. The polymeric contribution to the stress requires knowledge of the evolution of polymer chains. In this work, we use a microscopic model, the finitely extensible nonlinear elastic (FENE) model, to capture the polymer behavior. The benefit of microscopic models is they remain faithful to the polymer dynamics without information loss via averaging. The downside is the computational cost needed to solve the thousands to millions of differential equations describing the microstructure. We thus describe a multiscale flow solver that utilizes GPUs for massively parallel, efficient simulations. We compare and contrast the microscopic model with its macroscopic counterpart under various flow conditions. In particular, significant differences are observed under nonlinear flow conditions, where the polymers become highly stretched and oriented.