Epoxy matrix composites reinforced with high-performance fibers such as carbon, Kevlar, and glass, exhibit excellent specific stiffness and strength in many mechanical applications. However, these composites are disappointingly non-recyclable and are usually disposed of in landfill sites, with no realistic prospect for biodegradation in reasonable time. In contrast, moldable composites with carbonized elastomeric matrices developed in the last decades possess attractive mechanical properties in final net-shape products and can also be incinerated or recycled. Many carbon and inorganic fillers have recently been evaluated to adjust the properties of carbonized elastomeric composites. Renewable organic fillers such as human or animal hair offer an attractive fibrous material with substantial potential for reinforcing composites with elastomeric matrices. Samples of unidirectional fiber composites (with hair volume fraction up to 7 %) and quasi-isotropic short fiber composites (with hair volume fraction up to 20 %) of human hair-reinforced nitrile butadiene rubbers (HH-NBR) were produced in the peroxide-cured and carbonized states. The samples were characterized using SEM, Raman spectroscopy and photoacoustic microscopy. Mechanical tests were performed in tension using a miniature universal testing machine. The expected effect of fiber reinforcement on the overall mechanical performance has been demonstrated for both cured and carbonized composites. Considerable enhancement of the elastic modulus (up to 10 times), ultimate tensile strength (up to 3 times) and damage tolerance was achieved. The evidence of satisfactory interfacial bonding between hair and rubber was confirmed by SEM imaging of fracture surfaces. The suitability of photoacoustic microscopy was assessed for 3D reconstruction of the fiber sub-system spatial distribution and non-destructive testing.

The microstructure of the coating during hot-dip galvanizing under industrial conditions of two structural steels, a low-silicon ASTM A36 steel and a high-silicon Q345B steel, both of commercial quality, have been characterized for industrial-relevant times. For both cases it is noted that the formation of the Fe-Zn phases begins in early stages during the heating of the steel, a situation in which all the phases are in the solid state. The characterization was carried out through traditional metallographic techniques including SEM-EDS and DRX equipment. The evolution in time of the microstructure of both steels is examined, being able to observe that the mechanism by which silicon accelerates the formation of Fe-Zn phases in galvanizing is related to the change in the energy of the interfaces caused by a silicon accumulation in the liquid phase in contact with the ζ layer. These results provided us with a deeper understanding of the phase evolution in the hot-dip galvanizing of high silicon steels.

In this study, a 5vol. % (TiBw+TiCp)/Ti composite pancake with a diameter of 260mm was prepared by casting followed by open die forging in (α+β) phase region. The microstructures of the composite pancake are inhomogeneous, in terms of both matrix microstructure and distribution of reinforcements. The matrix microstructures were gradually refined from the periphery to centre of the pancake. The TiBw and TiCp reinforcements tend to be uniformly distributed in the centre region and. It is suggested that the microstructure difference can be mainly ascribed to the temperature variation from the periphery to the centre. Additionally, tensile testing results showed that the centre region of the composite pancake exhibits higher strength than the peripheral region. The strengthening mechanism and the softening behavior of the composite pancake with temperature is discussed.

The spontaneous combustion of coal in goaf is the main cause of mine fire at present. Lignite has become a major hidden danger in mine production safety because of its easy oxidation. In this paper, an innovative strategy was proposed to inhibit the spontaneous combustion of lignite by using the principle of microbial-induced calcium deposition. Based on the optimized culture method, a novel composite inhibitor of Bacillus pasteurelli was prepared. SEM, pore size analysis and FT-IR experiments were carried out simultaneously, and the oxidation properties of lignite before and after inhibition were quantitatively characterized from the perspective of microstructure, and the flame retardant properties of microbial and chemical retardants on coal samples were compared. The results show that a large number of deposited calcium carbonate particles are obviously attached to the surface of lignite after microbial inhibition treatment, which plays a physical oxygen insulation role. At the same time, the total pore volume and specific surface area of the coal sample decreased by 68.49% and 74.01%, respectively, indicating that microbial inhibitors can effectively plug the primary pores of lignite. Based on the peak measurement of 400-4000cm-1 infrared spectrum of coal samples, it is found that the contents of active groups including hydroxyl, carboxyl and methyl/methylene in lignite molecules after microbial inhibition are lower than those in raw coal, especially the methyl/methylene content involved in the initial oxidation reaction decreased by 96.5% compared with the baseline content in raw coal. The results show that the oxidation and self-heating capacity of lignite after microbial inhibition is effectively restrained in the initial spontaneous combustion. The research results of this paper can provide effective solutions for the prevention and control of coal spontaneous combustion risk in mined-out area.

In this paper, based on our previous expertise on ceramic artifacts, several archaeometric methods applied to some samples collected from the Dudești archaeological site (Oltenia region, Romania) are reported for the first time in the literature. The chemical composition and microstructural and morphological characterization of these samples offer important conclusions about the processing conditions. Some specific techniques such as X-ray diffraction (XRD), wave-length-dispersive X-ray fluorescence (WDXRF), Optical microscopy (OM), stereomicroscopy, scanning electron microscopy (SEM), Fourier transform infrared (FTIR) spectroscopy and Raman spectroscopy, provide composition information about pigments and their decay processes. Additionally, the Brunauer-Emmett-Teller (BET) method helps to estimate pore sizes and specific surface areas. Thermal analysis (TGA) was used to establish details regarding the production technology and the raw materials source used to make the ceramics, too. The obtained results indicated that the ceramics are based on a paste of muscovite, feldspar, with high plasticity, quartz, melanterite, and calcite, the latter in very low concentrations. According to the obtained results, we could assume that non-calcareous clays are present in the investigated samples because calcium exists in low concentrations. Gypsum is present, too, in very low concentration, identified by the presence of sulfate group in WDXRF. In the same context, iron oxides significantly impact the firing atmosphere of iron-rich clay, resulting in blackening under reducing conditions and reddish coloration under oxidative conditions. Using hematite and gypsum as pigments further contributes to the color variations in the pottery. The consistent firing temperature range of 200-600 °C in Dudești pottery implies a standardized production process, the variation in color being dependent on the specific reducing/oxidative regime conditions. This relationship between clay composition and local sources suggests a connection to Neolithic pottery production in the region and their color depending on the reducing/oxidative regime conditions.

The objective of this study is to conduct a mineralogical and chemical characterization of the mortars Roman archaeological site of Volubilis to rebuild spare mortars for restoration. We take samples of mortar, broken tile palate garden, and pavement mosaic Falavius Germanus houses. The analysis by X-ray diffraction reveals the coarse mortar Flavius Germanus is made of quartz and calcite with feldspar and probably, mica and dolomite in small amounts. The binder end is formed calcite and quartz. However, the broken tile mortar is formed by coarse particles, clay base mixed with a binder phase dominated by calcite. These results allowed us to reformulate spare mortars for the restoration of damaged Roman mosaics. The mortars are made up by 63.6% of lime and 36.4% of sand(with 4.19% of large grain, 71, 04% of coarse sand, 24.22%, of fine sand and 0.55% fines parts).The performance of these mortars was tested by mechanical testing.

Composite fiber materials are superior materials due to their high strength and light weight. Composites reflect the properties of their constituents, which is proportional to the volume fraction of each phase. There are different fiber reinforcement types and each affects it’s flexural, tensile and compression strength. When selecting a composite for a specific application, the forces excreted on the composite must be known in order to determine the reinforcement type. Unidirectional fiber reinforcement will allow very strong load resistance but only in one direction where as a random orientated fiber reinforcement can resist less load but can maintain this quota in all directions. These materials are said to be anisotropic. Certain composite fibers, taking into consideration there weights, are physically stronger than conventional metals. This research deals with the analysis of three composite materials with different reinforcement types, volume fraction and phase content. It was found that material A (glass epoxy) was the strongest in the longitudinal direction with a flexural strength of 534 MPa in the longitudinal and 420 MPa in the transverse direction. The flexural stresses of material B (glass silicone) and material C (glass polyester) where both found in the 120 to 135 MPa range. Differences were due to their differences in matrix composition and reinforcement type.

Adjunctive treatment of periodontitis lacks solutions allowing enough time for wound healing in the periodontal pockets by avoiding a fast re-colonization. Such a solution might be an antibiotic containing formulation with a controlled release over weeks. Here, a recently described minocycline containing approach is qualified for further clinical development by focusing on proof-of-concept, systemic burden, resistance development and degradation studies. Animal studies were done in two different (mouse-chamber, rat Porphyromonas gingivalis challenging) models, including effects on inflammation markers, bone loss and bone structure. Also, serum concentrations of minocycline after local application were determined by HPLC-MS/MS. The resistance status of bacterial clinical isolates against minocycline was investigated and the degradation of the formulation was characterized by laser scanning- and scanning electron microscopy. Animal studies clearly demonstrated the applicability of the new formulation in the investigated models. Inflammation markers decreased dosage dependent and reduced bone loss compared to non-treated group was observed. Thereby, the systemic burden of the antibiotic was neglectable. Minocycline is still effective against oral pathogens; resistance development was not seen. The biodegradable thread was first swollen and subsequently degraded over weeks. The results support the continued clinical development of this new formulation. A phase I clinical trial is planned to further evaluate its safety and efficacy.

The rational design of magnetic carbon composites, encompassing both composition and microstructure, holds significant potential for achieving exceptional electromagnetic wave absorbing materials (EAMs). In this study, FeCo@CM composites was efficiently fabricated through an advanced microwave plasma assisted reduction chemical vapor deposition (MPARCVD) technique, offering high efficiency, low cost, and energy-saving benefits. By depositing graphitized carbon microspheres, the dielectric properties were significantly enhanced, resulting in improved electromagnetic wave absorption performances through optimized impedance matching and a synergistic effect with magnetic loss. A systematic investigation revealed that the laminar-stacked structure of FeCo exhibited superior properties compared to its spherical counterpart, supplying a higher number of exposed edges and enhanced catalytic activity, which facilitated the deposition of uniform and low-defect graphitized carbon microspheres. Consequently, the dielectric loss performance of the FeCo@CM composites was dramatically improved due to increased electrical conductivity and the formation of abundant heterogeneous interfaces. At a 40 wt% filling amount and a frequency of 7.84 GHz, the FeCo@CM composites achieved a minimum reflection loss value of -58.2 dB with an effective absorption bandwidth (fE) of 5.13 GHz. This study presents an effective strategy for developing high-performance EAMs.

Coal currently accounts for over 38% of electric power generation around the globe. Hence, it is a significant critical contributor to socio-economic growth and development, particularly in the BRIC economies. The success of the coal energy in these nations in addition to the discovery of vast new coal deposits have revived Nigeria’s interest in coal power. However, there is lack of comprehensive data on the pollution emission profiles, along with the physicochemical, thermal, and kinetic properties of Nigerian coals as required for power plant operations. Therefore, this paper presents preliminary findings on the physicochemical, microstructural, mineralogical and thermal properties of Owukpa (WKP) coal from Benue State in Nigeria. The results showed that WKP contains high compositions of combustible elements and heating value but low pollutant elements. Furthermore, thermal degradation revealed high conversion efficiencies particularly under oxidative conditions as required for electric power generation through combustion.

Superconducting YBa2Cu3Oy (YBCO) foams were prepared using commercial open-cell, polyurethane foams as starting material to form ceramic Y2BaCuO5 (Y-211) foams which are then converted into superconducting YBCO by using the infiltration growth process. For modelling the superconducting and mechanical properties of the foam samples, a Kelvin-type cell may be employed as a first approach like done in the literature for pure polyurethane foams. However, for a refined model of a superconducting foam sample, the real sample structure must be considered. Thus, a proper description of the specific microstructure of the superconducting YBCO foams is required. A variety of parameters including the cell size and shape, the window size and shape, the length and shape of the foam struts or ligaments and the respective angles of intersection are used to describe the real foam structure. To obtain a set of reliable data, YBCO foam samples were investigated using optical microscopy, SEM and electron backscatter diffraction (EBSD). The detailed investigation of the foam microstructure reveals not only the differences to the polymeric foams used as base material, but also gives insight to details of the infiltration growth process via the increased surface amount in a foam sample.

Plasma Electrolytic Oxidation (PEO) is a surface treatment, similar to anodizing, that produces thick oxide films on the surface of metals. In the present work, PEO coatings were obtained on zinc-aluminized (ZA) carbon steel using as electrolyte a solution containing sodium silicate and potassium hydroxide, and working with high current densities and short treatment times in DC mode. The surface morphology resulted the typical one of PEO layers, with the presence of a lot of pores and micro-cracks. Considering the cross section, the thickness of the coating was strongly influenced by the process parameters, with different dissolution grades of the ZA layer depending on the current density and treatment time. The PEO layer resulted mainly composed by aluminum and zinc oxides and silicates. The corrosion resistance was remarkable increased in the samples with the PEO coating.

Marine clay deposits are commonly found worldwide. Considering the cost of dumping and the related environmental concerns, an alternative solution involving the reuse of soils that have poor conditions is crucial. In this research, the authors examined the durability of marine deposited clays and compiled a corresponding database. The use of slag alone as a binder, at any percentage, increased the accumulated mass loss (ALM) up to 2%. However, the use of lime as the third binder seemed to accelerate the chemical reactions associated with the hydration of clay and cementitious material and to enhance the chemical stability, i.e., samples that included both lime and slag experienced the same ALM as samples treated with cement only. Scanning electron microscopy analysis confirmed the durability improvements of these clays. The proposed unconfined compressive strength and accumulated mass loss relationship yielded practical approximation for the fine- and coarse-grained soils blended with up to three binders until 60 days of curing.

Finely ground glass has the potential for pozzolanic reactivity and can serve as a supplementary cementitious material (SCM). Glass reaction kinetics depends on both temperature and glass composition. Microstructural modeling is a helpful approach to get better understanding of cement hydration and microstructure development. Mechanical and performance properties of concrete are directly related to the development of concrete microstructure, which is the consequence of progress in cement hydration. This study initially provides a comprehensive background about cement hydration process and microstructural modeling of the hydration. It then utilizes results of experimental studies, i.e. isothermal calorimetry and thermogravimetric analysis, to find kinetics equation parameters called “Avrami Constants”. For the first time, these constants were found for three main components of cement, i.e. C₃S, C₂S, and C₃A, and also for glass particles smaller than 25 µm. Although modeling of cement hydration and cementitious systems containing single glass particles showed promising results, simulations of combined glass types and sizes showed that more work on microstructural models is needed to properly model the reactivity of mixed glass particle systems.

The goal of this research is to determine the optimal microwave-assisted sol-gel synthesis pa-rameters of TiO2 nanoparticles with the achievement of the crystalline TiO2 nanoparticles with the highest specific surface area and the lowest energy band gap. Titanium isopropoxide was used as a precursor to prepare the sol (colloidal solution) of TiO2, isopropanol as a solvent, acetylacetone for complexation, and nitric acid as a catalyst. Four samples of titanium dioxide were synthesized from the prepared colloidal solution in a microwave reactor at a temperature of 150 °C for 30 minutes and at a temperature of 200 °C for 10, 20, and 30 minutes. The phase composition of the prepared samples was determined by X-ray diffraction analysis (XRD) and Fourier-transform infrared spectroscopy (FTIR). Nitrogen adsorption/desorption isotherms were used to determine the spe-cific surface area and pore size distributions by Brunauer-Emmett-Teller (BET) method. The band gap energy values of the TiO2 samples were determined by diffuse reflectance spectroscopy (DRS). CrystallineTiO2 nanoparticles with the highest specific surface area and the lowest energy band gap were obtained for the TiO2 sample synthesized at 200 °C for 10 minutes.

Carotid atherosclerotic lesions are a major cause of cerebrovascular disease (CVD). Identification and quantification of carotid plaques are important for categorizing the vulnerability of plaques for rupture and assessing the impact of treatments. The irregularity of plaque surface is associated with previous plaque rupture and plays an important role in the risk of stroke. Thus, the aim of this study is to develop and validate novel vulnerability biomarkers from three-dimensional ultrasound (3DUS) images by analyzing the surface morphological characterization of carotid plaque using fractal geometry features. 3D box-counting and 3D blanket are the two types of 3D fractal dimension that were employed to describe the smoothness of plaques. This fractal dimension analysis tool was used to evaluate the effect of atorvastatin using 3DUS carotid images, which were acquired from 6 patients treated with atorvastatin with 80 mg daily and 5 patients with placebo. The Student's T Test results showed that those two fractal features were effective for detecting the statin-related changes in carotid atherosclerosis with p<0.0068 and p<0.015 respectively, suggesting that 3D fractal dimension measurements can be used effectively to analyze the surface characteristics of carotid plaques, especially for evaluating the impact of the treatment.

The growing demand for nutritious foods has spurred investigations into alternative sources of nutrition beyond traditional options. For this reason, the present study approaches the amaranth, which is a plant with high potential, highlighting the morphological growth, grain biomass pro-duction, and quantitative traits of seven varieties of amaranth cultivated in the pedoclimatic con-ditions of Somes meadow in Transylvania. A bifactorial trial was implemented with factors ama-ranth species and amaranth varieties. Two amaranth species and seven varieties were studied. Differences are reported between morpho-productive and quantitative traits of the seven amaranth varieties studied in this research. The interrelationships between amaranth morphological traits quantified by using Pearson simple correlations show that morphological traits moderately con-tribute to grain fresh biomass yield, while morphological traits and fresh biomass strongly con-tributed to grains dry biomass yield. Our study shows that morpho-productive, and nutritional characteristics of the seven amaranth varieties comprised by our study recommend the plans to be used in various nutritional aims, being a valuable replacer of traditional raw materials in specific food and feed industry sectors.

Functional articular cartilage regeneration remains an unmet medical challenge, increasing the interest for innovative biomaterial-based tissue engineering (TE) strategies. Hydrogels, 3D macromolecular networks with hydrophilic groups, present articular cartilage-like features such as high water content and load-bearing capacity. In this study, 3D porous polyethylene glycol diacrylate (PEGDA) hydrogels were fabricated combining the gas foaming technique and an UV-based crosslinking strategy. The 3D porous PEGDA hydrogels were characterized in terms of their physical, structural and mechanical properties. Our results showed that the size of the hydrogels pores can be modulated by varying the initiator concentration. In vitro cytotoxicity tests showed that 3D porous PEGDA hydrogels presented high biocompatibility both with human chondrocytes and osteoblast-like cells. Importantly, the 3D porous PEGDA hydrogels supported the viability and chondrogenic differentiation of human bone marrow-derived mesenchymal stem/stromal cells (hBM-MSCs)-based spheroids as demonstrated by the positive staining of typical cartilage extracellular matrix (ECM) (glycosaminoglycans (GAGs)) and upregulation of chondrogenesis marker genes. Overall, the produced 3D porous PEGDA hydrogels presented cartilage-like mechanical properties and supported MSC-spheroid chondrogenesis, highlighting their potential as suitable scaffolds for cartilage TE or disease modelling strategies.

The aim of the work is to study the effect of the 3D printing process on the microstructural and hydrophilic properties of polylactic acid (PLA) samples with various model printing patterns obtained from the black Filament PLA by sequentially applying polymer layers using the FDM (Fused Deposition Modeling) method. X-ray phase analysis revealed partial crystallization of PLA polymer chains in printed samples, which occurs under thermal and mechanical action on the original amorphous PLA filament during 3D printing to varying degrees, depending on the geometry of the pattern and the morphology of its surface. At the same time, IR spectroscopy data indicate the preservation of all intrastructural chemical bonds of polylactide. Measured at the original installation, the values of the wetting edge angles on the surface of the printed samples are in the range φ = 50-60°, which is significantly less than the right angle. This indicates the hydrophilic properties of all samples’ surface. At the same time, the influence of different geometries of model drawings in printed samples was found not only on the morphology of the samples’ surface according to SEM data, but also on its wettability.

This research presents a comprehensive bibliometric and sentiment analysis of nanocomposite literature from 1990 to 2024. Employing cutting-edge computational methods, the study delves deep into the progression of microstructural characterization, electrical properties, and mechanical behaviors of nanocomposites. The analysis utilizes advanced Boolean search strategies from the Scopus database, ensuring a thorough extraction of thematic content. The results explore various themes and insights, shedding light on trends evident in the Scopus database, particularly the prominence of research on nanocomposite microstructure, electrical attributes, and mechanical performance. The paper also offers textual analytics and bibliometric data, showcasing critical collaborative efforts and influential studies. Significant discoveries encompass the evolution of research language, shifts in thematic focus, and global contributions, providing a comprehensive perspective on the current landscape of nanocomposite research and its dynamic evolution. Moving forward, the "State-of-the-Art and Gaps Extracted from Results and Discussions" section of the paper delves into the most recent advancements in nanocomposite research. It delves into various types of nanocomposites, with a particular emphasis on their microstructural characteristics, electrical properties, mechanical dynamics, and the application of nanocomposite films. This section identifies key research themes, traces historical progress, and highlights emerging trends while underscoring the significance of collaboration and the influence of pivotal studies that have shaped the field. Lastly, in the "Literature Review Guided by Artificial Intelligence" section, the paper introduces a revised approach for researching nanocomposites through AI-guided techniques. This approach prioritizes articles published in 2023 based on citation frequency. Here, the focus is on exploring the relationship between nanocomposites and their electrical properties, emphasizing their fundamental interactions and impact on electrical characteristics. Various nanocomposite systems are covered, highlighting their composition, structure, and functionality. Findings from recent studies are integrated to provide a comprehensive overview of the current state of knowledge in this area. Notably, the sentiment analysis, anchored by an average sentiment score of 0.638771, underscores a positive trajectory in academic discourse, emphasizing the growing recognition of the potential of nanocomposites. The bibliometric exploration maps the intellectual domain, emphasizing pivotal research themes and the influence of crosslinking time on nanocomposite attributes. While this study is thorough, it acknowledges its limitations and advocates for broader database inclusion in future research endeavors. This work elucidates the prevailing trends in nanocomposite research, emphasizing the indispensable role of computational tools in comprehending this vast wealth of information.

The microstructural evolution, thermodynamics and kinetics of Mo-21%Tm₂O₃ (mass fraction, %) powder mixtures during ball milling were investigated using X-ray diffraction and transmission electron microscopy. Ball milling induced Tm₂O₃ to be decomposed and then dissolved into Mo crystal. The supersaturated nanocrystalline solid solution of Mo (Tm, O) was obtained after 96 h of ball milling. The elements of Mo, Tm and O were distributed uniformly in the ball-milled particles. Based on the semi-experimental theory of Miedema, a thermodynamic model was developed to calculate the driving force of phase evolution. There was no chemical driving force to form a crystal solid solution of Tm atoms in Mo crystal or an amorphous phase because the Gibbs free energy for both processes was higher than zero. For Mo-21%Tm₂O₃, it was mechanical work, not negative heat of mixing, that provided the driving force to form supersaturated nanocrystalline Mo (Tm, O) solid solution.

This work deals with the analysis of phase composition of sintered Ti-Al-C composite materials under high voltage electrical discharge. The samples of Ti-Al-C powder composites were tested by SEM, Raman spectroscopy and XRD. It was determined that the treatment of the powder by high voltage electrical discharge (HVED) and further sintering at high temperatures using the method of spark plasma sintering (SPS) encourages the formation of the intermetallic reinforcing phases, carbides and different nanocarbon structures like graphene and fullerenes, as well as pure graphite. Intermetallic phases and nanocarbon structures improve mechanical and physical properties of the composites. By using experimental methods mentioned above, the phase composition of Ti-Al-C powder composites obtained at different sintering temperatures was determined.

The aim of this study was to research the quality parameters of honeys directly from Iraqi Kurdistan beekeepers and to compare with European Union law and Central European honeys. In total 30 honey samples directly from Kurdish, Czech and Slovak beekeepers were collected from the year of production 2018. The analyzed physicochemical parameters and bioactive compounds (moisture content, electrical conductivity, diastase activity, hydroxymethylfurfural content, pH, free acidity, total phenolic content, color, color intensity) varied depending on the botanical and geographical origin of honeys. Comparing Kurdistan honeys with a directive relating to honey, only two honey samples had diastase activity lower than limit and one sample had free acidity value at the legislative limit. Based on the results, it was found that the properties of Kurdistan honeys were very similar to the properties of Czech and Slovak honeys, as indicated by the detected statistically non-significant differences (p > 0.05) between the moisture content, electrical conductivity, diastase activity and color. On the contrary, the most significant differences (p < 0.01) were detected in hydroxymethylfurfural content, total phenolic content, and color intensity. Our results indicated the specific properties and the uniqueness of honeys from Iraqi Kurdistan and pointed to the possibility of trading this honey in Europe.

German noise action plans aim to reduce negative health outcomes from noise exposure and identify quiet areas free of noise pollution. Quiet area identification in German noise action plans is based primarily on noise mapping and spatial analysis and not empirical or qualitative data about acoustic environments, thus leaving a gap in the understanding of the quality of formally recognized quiet areas in noise action plans. This work presents a comparative empirical case study in Dortmund, Germany, with the aim to describe the diurnal dB(A) and biophonic properties of quiet areas versus noise 'hot spots'. Sound observations were collected (n=282,764) in five different natural or recreational land use patch types larger than four acres within 33 proposed quiet areas in Dortmund (n=70) and 23 noise hot spots between April 27^th, 2022 and March 2^nd, 2023. We find that quiet areas are on average more than 20 dB(A) quieter than noise hot spots almost every hour of the day. Forests, managed tree stands, cemeteries, and agriculture diel patterns are dominated by dawn dusk chorus in spring and summer, whereas sport and recreation as well as noise hot spots are dominated by traffic and human noise. A novel composite biophony mapping procedure is presented that finds distinct temporal distribution of biophony in forested and agriculture peri-urban locations positively associated with patch size, distance away from LDEN > 55, proximity to water, and the number of vegetation layers in the plant community. Anthrophony distribution dominates urban land uses in all hours of the day, but expands during day and evening and contracts at night and in dusk hours. The procedures presented here illustrate how qualitative information regarding quiet areas can be integrated into German noise action planning.

Conventional heat treatment is not capable of converting a sufficient amount of retained austenite into martensite in high-carbon or high-carbon and high-alloyed iron alloys. Cryogenic treatment induces the following alterations in the microstructures: (i) a considerable reduction in the retained austenite amount, (ii) formation of refined martensite coupled with an increased number of lattice defects, such as dislocations and twins, (iii) changes in the precipitation kinetics of nano-sized transient carbides during tempering, and (iv) an increase in the number of small globular carbides. These microstructural alterations are reflected in mechanical property improvements and better dimensional stability. A common consequence of cryogenic treatment is a significant increase in the wear resistance of steels. The current review deals with all the mentioned microstructural changes as well as the variations in strength, toughness, wear performance, and corrosion resistance for a variety of iron alloys, such as carburising steels, hot work tool steels, bearing and eutectoid steels, and high-carbon and high alloyed ledeburitic cold work tool steels.

Secondary microplastic (MPL) and nanoplastic (NPL) particles exhibit different physiochemical characteristics that attenuate their toxicities in different ways: some particle types being well documented (primary) while other (secondary), are more unknown. Fourier Transform Infrared Spectroscopy (FTIR), Raman, Proton Nuclear Magnetic Resonance (H-NMR), Curie Point-Gas Chromatography-Mass Spectrometry (CP-gc-MS), Induced Coupled Plasma-Mass Spectrometry (ICP-MS), Nanoparticle Tracking Analysis (NTA), Field Flow Fractionation-Multiple Angle Light Scattering (FFF-MALS), Differential Scanning Calorimetry (DSC), Thermogravimetry (TGA), Differential Mobility Particle [Sizing] (DMPS), Scanning Electron Microscopy (SEM), Transmission Electron Microscopy (TEM), and Scanning Transmission X-ray Microspectroscopy (STXM) are re-viewed as part of a suite of characterization methods for physiochemical ascertainment and distinguishment. Organizations, like the water treatment or waste management industry, and those in groups that bring awareness to this issue, which are in direct contact with the hydrosphere, can utilize these techniques in order to sense and remediate this plastic polymer pollution. The primary goal of this review paper is to highlight the extent of plastic pollution in the environment as well as introduce its effect on the biodiversity of the planet while underscoring current characterization techniques in this field of research. The secondary goal involves illustrating current and theoretical avenues in which future research needs to address and optimize MPL/NPL remediation, utilizing nanotechnology, before this sleeping giant of a problem awakens.

In this study, nanostructured cerium-doped TiO2 (Ce-TiO2) films with the addition of different amounts of cerium (0.00, 0.08, 0.40, 0.80, 2.40, and 4.10 wt. %) were deposited on a borosilicate glass substrate, by flow coating sol-gel process. After flow coating, deposited films were dried at the temperature of 100 °C for 1 h, followed by calcination at the temperature of 450 °C for 2 h. For the characterization of sol-gel TiO2 films, the following analytic techniques were used: X-ray diffraction (XRD), thermal gravimetry (TG), differential thermal analysis (DTA), and differential scanning calorimetry (DSC). Sol-gel derived Ce-TiO2 films were used for photocatalytic degrada-tion of the ciprofloxacin (CIP). The influence of the amount of Ce in TiO2 films, the duration of the photocatalytic decomposition, and the irradiation type (UV-A and simulated solar light) on the CIP degradation were monitored. Kinetics parameters (reaction kinetics constants and the half-life) of the CIP degradation, as well as photocatalytic degradation efficiency, were determined. The best photocatalytic activity was achieved by the TiO2 film doped with 0.08 wt.% Ce, under both UV-A, and solar irradiation.

Grape dehydration is practiced widely in the food industry with large yields of sultanas produced globally. This paper proposes an investigation into grape microstructure changes as it is dried by imaging specimens at intervals during dehydration at two temperatures using scanning electron microscopy. Detailed images of the microstructure were obtained, and a unique image processing algorithm was developed to quantitatively analyse the properties of this microstructure. Two main methods were developed to obtain the complex boundaries of cells present in the grape tissue in over 36 SEM images. Segmentation of the binary image using an adapted watershed function obtained the most consistent and accurate morphological shape. This was compared to a secondary method which used Canny’s edge detection function, morphological closing and skeletonizing to outlines the cellular microstructure. MATLAB was utilised to convert these boundaries into measurable areas so that quantitative data on average cell area, perimeter and cell axis lengths was acquired. It was found that over drying time cell area and perimeter reduced as expected. Some variability in the data was clear due to only single samples being analysed for each temperature and time combination. The development of automatic image processing techniques will enable quantitative data to be extracted from these images. Trends in cell perimeter, diameter and shape will be used to demonstrate relationships between morphological structure, drying temperature, and duration.

This study aims at relating the microstructural arrangement, in particular the symmetry materialised by filament sequencing in fused filament fabrication process on mechanical behaviour of printed polyamide. Dogbone structures are printed using various printing temperatures, which are combined with part orientation and raster angle that represent the in-plane and out-of-plane symmetrical arrangement of filament. Mechanical testing is conducted on both as-received filaments and printed structures to derive the effect of filament arrangement symmetry and process-generated defects on mechanical loss. In addition, microstructural analysis using scanning electron microscopy is used to share more light on the filament arrangement and their consequence on deformation mechanisms with respect to the printing conditions. The results show that 3D printed polyamide-based material exhibit remarkable tensile performance with strain stiffening behaviour and large elongation at break thanks to particular filament layout. Among the considered printing conditions, the part orientation is found to have the largest influence on tensile behaviour, which modulates the behaviour from complete restoration of the filament performance to mechanical loss.

Fabry-Perot air chamber was constructed at the melting point (splicing location) of two single-mode fibers by glycerin assisted self-expansion method. The morphology of the Fabry-Perot air chamber was fabricated and optimized by modulating the splicing parameters (drawing process, discharging location, time and intensity) and the fibers’ end-face (plane or arc). The in-line or reflected Fabry-Perot cavities have been applied to determine the tensile strain in the range of 0-1.2 N. The train sensing performance of the spherical shaped FP cavity has been experimentally demonstrated with the best sensitivity of 3.628 nm/N, corresponding to the resolution of ~0.005 N. The proposed FP fiber sensor has the advantages of low cost, fast fabrication and easy-integration with the common fiber system.

In the drive towards environmental restoration and sustainable energy solutions, effective utilization and management of agricultural crop residues are vital to mitigate greenhouse gas (GHG) emissions and waste accumulation. Converting biogenic wastes into biofuels and bioproducts has the potential to tackle the energy crisis and contribute to environmental remediation. In this investigation, teff husk, primarily generated in Ethiopia during teff production within the agro-industrial sector, is used as the feedstock for the slow pyrolysis process. In Ethiopia, it is estimated that over 1.75 million tons of teff husk are generated annually, with a significant portion being incinerated in the fields, resulting in substantial environmental pollution. This study focuses on assessing teff husk as a potential material for slow pyrolysis, a crucial stage in biochar production, to tap into its biochar-producing potential. To determine the composition of the biomass, the teff-husk was initially analyzed by thermogravimetry. The significant presence of fixed carbon indicates that teff husk is a viable candidate for pyrolytic conversion into biochar particles. The process of slow pyrolysis took place at three varied temperatures—specifically, at 400, 450, and 500 °C. Process parameters of slow pyrolysis such as reaction time, temperature, and heating rate were enhanced to obtain maximum biochar yields. The highest biochar yield of 43.4 wt% was recorded at optimized reaction time, temperature, and heating rate of 120 min, 400 °C, and 4.2 °C/min, respectively. Furthermore, biochar's physicochemical, SEM-EDX, FTIR, and TGA characterization were performed. The thermal stability and carbon content of biochar were found to rise at higher temperatures. Unlike fuel recovery, the results suggest that teff-husk can be used as a feedstock for biochar production.

A new Mg-Zn-Zr-Ca alloy in powder state was obtained via mechanical alloying method, from pure elemental powder. Further, the obtained powder-alloy was processed by selective laser melting (SLM) procedure to obtain 3D printed samples for small biodegradable implants. A series of microstructural, mechanical and corrosion analysis were performed. The SEM analysis of powder-alloy reveal a good dimensional homogeneity, with uniform colored, no agglutinated and almost rounded particles, suitable for selective laser melting procedure. Further, the SLM samples reveal a robust and unbreakable morphology, with a suitable porosity and without undesirable balling effect. The tested Young’s modulus of the SLM samples, of 42 GPa, is close to cortical bone one, of 30 GPa. The corrosion tests performed in PBS (Phosphate-buffered saline) solution show that the corrosion parameters have a satisfactory evolution.

During 2021 and 2022 summers, we measured the total and dissolved (&lt; 0.45 mm) concentration of 25 elements in Utah Lake using Inductively Coupled Plasma Optical Emission Spectrometry (ICP-OES). Utah regulates twelve of these elements. ICP-OES sensitivity is at the ppb-level but is not the approved regulatory method. All regulations are for dissolved concentrations; except aluminum (Al) and phosphorus (P) which are for total recovery. We found total Al concentrations above allowable, but dissolved concentrations were well below allowable concentrations. We attribute high total concentrations to suspended clays. Dissolved copper (Cu) concentrations were below regulatory levels in 2021, but some samples were above regulatory levels in 2022. This could be related to the use of Cu-based algaecide treatments, or from other sources. Lead (Pb) data were inconclusive; dissolved Pb concentrations were well below the acute (1-hour average) limit, but the chronic concentration limit (4-hour average) is below the ICP-OES minimal detection limit. Arsenic (As) concentrations exhibit a seasonal trend that we attribute to groundwater inflows. This ppb-level study provides insight into regulated elements in Utah Lake previously not available due to the high sensitivity of the method and measurements of both total and dissolved concentrations.

Nowadays, the identification and characterization of grapevine cultivars resilient to climate and water stress while preserving quality traits is crucial for the wine industry. Therefore, the objective of this work was to characterize according to their aromatic potential 9 white and 6 red minority cultivars recently recovered from Castilla-La Mancha region (Spain), subjected at two different water deficit regimes: rainfed, with subsistence irrigation, and irrigated. For this, the varietal aromatic potential index (IPAv) and the detailed aromatic composition were analyzed by HS-SBSE-GC/MS, in extracts of two different ph. For IPAv values, red varieties did not show a clear trend with respect to irrigation. However, in white minority varieties, higher values were obtained under irrigation conditions. Thus, a clear differentiation of the minority varieties in comparison to the references was observed, primarily attributed to the content of esters and acids, in both white and red varieties. A notable contrast was observed at different pH, indicating a greater extractability of certain compounds like linalool, under more acidic conditions. This suggests that some recovered minority cultivars could be promising for cultivation in semi-arid regions with limited water, contributing to the wine sector sustainability in the future.

Members of the genus Armillaria are widespread forest pathogens against which effective protection has not yet been developed. Due to their longevity and the creation of large-scale cloning of Armillaria individuals, the use of mycoviruses as biocontrol agents (BCAs) against these pathogens could be an effective alternative. This work describes the screening of double-stranded RNA banding patterns as a first approach for potential virus discovery and the use of stranded total RNA-seq for viral detection and characterization in Armillaria spp. collected in the Czech Republic. A total of five single-stranded RNA viruses were detected in Armillaria ostoyae and A. cepistipes, including the first virus of the family Tymoviridae found infecting a member the genus Armillaria and four viruses belonging to the recently described virus group "ambiviruses" with circular ambisense genome organization. Both hammerhead (HHRz) and hairpin (HpRz) ribozymes were detected in all the ambiviricot sequences. Armillaria viruses were compared by phylogenetic analysis and confirmed their specific host by direct RT-PCR, which showed the occurrence of interspecies transmission.

In this study, the efficiency of coating (alginate and carrageenan) and osmotic dehydration pre-treatment (NaCl and sucrose) on decreasing oil uptake of potato strips was assessed. It was examined how various pre-treatments affected the sample’s texture, morphology, color and density properties as well as their moisture content and effective moisture diffusion coefficient (Deff). Results showed that NaCl osmotic dehydration pre-treatment and sucrose solution decreased oil uptake by 30.76% and 41.75%. This is attributed to moisture removal increasing caused by improving dielectric properties. Osmotic dehydration and coating pre-treatment frequently enhanced product shrinkage, browning index, a* and ∆E. Conversely, density, lightness, breaking force, Deff and b* decreased. In control samples, SEM revealed a severely damaged internal structure in comparison to a tissue homogenous layer produced by coating. For moisture loss and oil uptake, the coefficient of determination (R2) and root mean square error (RMSE) of eight empirical models were compared. Finally, the Dehghannya and Krokida model (moisture loss) and the Movahhed and Naghavi model (oil uptake) were found the best fit to the experimental data. Although coating pre-treatment and osmotic dehydration can be used as an alternate de-oiling approach for potato chips, the mechanism of oil uptake reduction differ.

The effects of 0.4wt.% Sc addition on a typical Al-Si10-Mg alloy were systematically investigated in the present research. Samples with and without Sc produced refined dendritic arranged microstructures with sensitivity to the aging treatment after solidification, particularly in the case of the alloy without Sc. After being exposed to 300°C for 90 minutes, the dendritic spacing nearly doubled in the Al-10wt.%Si-0.45wt.%Mg samples. The rapidly solidified microstructures were constituted by the -Al dendritic phase surrounded by eutectic phases/intermetallics such as Si, Mg2Si and Al3Sc (in the case of the alloy containing Sc). 255°C and 300°C were deemed most appropriate temperatures for aging treatments, with four exposure times of up to 120 minutes tested for each alloy. The heat treatments allowed the Vickers hardness profiles to be plotted and compared. Moreover, in order to detect both Sc- and Mg- precipitates after aging, specific samples have been prepared for either SEM or TEM analyses. At first, the results pointed to a strong precipitate-related hardening effect formed as a result of the Sc addition to the alloy. All samples containing Sc showed a higher hardness value when compared to their respective treated samples without Sc. Secondly, when comparing the Al-10Si-Mg-Sc alloy samples among themselves after being treated at different conditions, high temperatures and excessive treatment times can become detrimental to the hardness. This was due to the growth of larger Sc-bearing precipitates of approximately 1 µm in size under such conditions, having less pronounced hardening effect. The best condition (255°C for 60 min) for as centrifuged samples in Cu-mold produced very fine dispersion of Mg- and Sc- intermetallics (~200 nm in size) with a peak hardness of 110 HV.

In this study, the olive pomace was considered because of its importance in the environment. So, this study carried out to estimate the total nitrogen content and the fatty acids profile of olive pomace. The olive pomace samples were collected from Irbid, Jarash, Ajloun and Mafraq during the harvesting season 2014 to study the biochemical characteristics of fatty acid composition and the total nitrogen (TN) content. The total nitrogen content was determined by standard Kjeldahl method and the fatty acid profile was detected by gas chromatography (GC). The results show that the total nitrogen content ranged from (0.39 ± 0.0) to (0.62 ± 0.02) with statistically significant difference suggesting that the composition of matrices and their percentage may be responsible for composition of amendments. The calculated total protein percentage ranged between (2.43 ± 0.00) to (3.87 ± 0.17). Also, 13 different fatty acids were quantitatively profiled and quantitated. Oleic acid (C 18:1) was found to be the highest percentage of all other fatty acids and ranged between (59.03%) and (63.81%), moreover the C 18:1/C 18:2 (oil quality) was calculated and C.V% showed variation meaning that nutritional implication could affect the oxidative stability of oils. In conclusion, OP by-product could give a sustainable and alternative-cheap source for fertilizers, pharmaceutical industries, cosmetics and other industries.

NongXiangXing Baijiu (NBJ) is produced using a solid-state fermentation system, but the impact of stratified fermented grains on fermentation remains unclear. Therefore, in a typical distillery plant, we evaluated the physical and chemical composition, volatile compound profile, and microbial community of fermented grains in NBJ both above (FG-A) and below (FG-B) the Huangshui line. Significant differences in fermentation parameters between FG-A and FG-B were observed after 30 days of fermentation (P < 0.05). Additionally, the partial least squares projection to latent structure discriminant analysis (PLS-DA) revealed distinct differences in volatile compounds between FG-B and FG-A, identifying 26 discriminant markers. The diversity of short-chain fatty acids (SCFAs) and their esters was higher in FG-B compared to FG-A. Furthermore, microbial diversity and abundance differed significantly between the two layers of fermented grains (P < 0.05). Correlation and pathway enrichment analyses indicated that the higher SCFA content in FG-B could be attributed to the greater abundance of acid-producing microorganisms compared to FG-A. This study highlights the differences between the two layers of fermented grains in NBJ fermentation, offering new insights into solid-state fermentation and expanding the current understanding of the traditional NBJ fermentation process.

Deep Eutectic Solvents (DESs) show promising abilities for the delamination of multilayer packaging films that are used in food packaging and in pharmaceutical blister packs. Due to the complexity of their structure, the recycling of these materials is a challenging task, leading to the easiest or cheapest option, landfilling. Towards the development of ‘green’ solvents for the efficient waste management and recycling, the conducted research focuses on the preparation of a range of hydrophobic and hydrophilic DES based on carboxylic acids. Also, their chemical and physical characterization, such as DSC, rheometer and density measurements, was followed for the determination of their properties. The laminate packaging waste products that were tested were Al/PE, PE/Al/PET, Al/PE/paper and PVC/PE/Al. Different batches of solvent systems were tested based on various naturally derived aliphatic and aromatic organic compounds as well as amino acids. The separated films were collected and studied further for the examination of the delamination extend. Results showed full or partial delamination of some materials as well as challenges of solvent systems. Variables such as temperature, agitation rate, mixing time and solvents ratios were monitored and collected during the design of experimental process. The results showed that the used DESs can offer an efficient, low-energy, affordable and green option for the delamination tested packaging materials.

In this study, Ni50Ti50 powder was coated on the surface of graphite substrate (C) by plasma spraying process using a radio frequency inductively coupled plasma reactor. The coating was carried out by using 12- and 9-kW power under Ar atmosphere. The cross-section of coating layers and the surface were examined with SEM, EDX, XRD analysis and microhardness test. The thickness and quality of the coating increased with input power. Many pores were detected in the cross-sectional surface areas. Higher input power caused a better coating layer in NiTi alloy. The hardness of the coating layer decreases with higher input power.

The high entropy alloy (HEA) of equiatomic composition CrNiFeCoMn and with FCC crystal structure was additively manufactured with a selective laser melting (SLM) process starting from mechanically alloyed powders. The as produced alloy shows finenitride and  phase pre-cipitates, which are Cr-rich and stable up to about 900 K. The precipitates increase in number and dimensions after long-period annealing at 900-1300 K, with a change in the HEA mechanical properties. Higher aging temperatures in furnace, above 1300 K, turn the alloy in a single FCC structure, with disappearance of the nitrate and  phase precipitates inside the grains and at the grain boundaries, but with still a presence of a finer Cr-rich nitride precipitation phase. These re-sults suggest that the as-produced HEA is a supersatured solid solution at low and intermediate temperature with nitrides and  nanostructures.

Recognition, decoding and tracking of vortex patterns is of increasing importance in many fields reaching from astronomical observation of distant galaxies to turbulence phenomena in liquids or gases. Currently, coherent light beams with orbital angular momentum (OAM) are of particular interest for optical communication, metrology, micro-machining or particle manipulation. One common task is to identify characteristic spiral patterns in pixelated intensity maps at real-world signal-to-noise ratios. Recently, Fast Fourier Transform (FFT) was applied to the quantitative analysis of spiral interference patterns of OAM beams. Our study considers this approach in more detail. It is demonstrated that specific information can be extracted by combining conformal mapping by polar transform with determining one- or two-dimensional angular frequency spectra either in spatially fixed or scanning mode. Results of proof-of-principle experiments are presented.

The application potential of cellulosic materials in natural composites and other fields needs to be explored to develop innovative, sustainable, lightweight, functional biomass materials that are also environmentally friendly. This study investigated Typha augostifolia (Typha sp.) as a potential new raw material for extracting cellulose nanocrystals (CNCs) for application in wastewater treatment composites. Alkaline treatments and bleaching were used to remove cellulose from the stem fibers. The CNCs were then isolated from the recovered cellulose using acid hydrolysis. The study showed a few distinct functional groups (O-H, -C-H, =C-H and C-O, and C-O-C) in the Fourier Transform Infrared (FTIR) spectra. Scanning electron microscope (SEM) revealed the smooth surface of CPC and CNCs that resulted from removing lignin and hemicellulose from powdered Typha augostifolia. Based on the crystalline index, the powdered Typha augostifolia, CPC, and CNCs were 42.86%, 66.94% and 77.41%. The loss of the amorphous section of the Typha sp. fiber resulted in a decrease in particle size. It may be inferred from the features of a Typha sp. CNC that CNCs may be employed as reinforcement in composites for wastewater treatment.

Glass and ceramics have a fundamental and crucial role in our lives due to their properties and aesthetic decoration. However, they create serious environmental problems, mainly due to their high occupation of landfills and harmful emissions. Both wastes could be utilized to reduce the natural resources' adverse environmental effects and exhaustion. With increasing environmental concerns to reduce solid waste as much as possible, the concrete industry has adopted several methods to achieve this goal. Hence this study examines the performance of self-compacted concrete (SCC) utilizing various percentages of recycled waste materials such as those deposited from glass and ceramic industries. The idea of utilizing recycled waste materials in concrete manufacturing has gained massive attention due to their impressive results in rheological and mechanical state. Recycled glass (RG) and ceramic waste powder (CWP) were utilized to replace fine aggregate and cement, respectively. Five mixes were designed, including the control mix, and the other four mixes with different dosages of RG and CWP as fine aggregate and cement replacement ranging between 5 to 25%. Mixes were tested for both rheological and mechanical properties to evaluate their compilment with SCC requirements as per codes and guidelines. The results revealed that 20%CWP or less as cement replacement and 10% or less of RG as fine aggregate replacement would provide suitable rheological properties along with mechanical ones. Utilizing recycled glass and ceramic waste powder provides strength like the mix designed with natural resources, which helps us structure economically and environmentally friendly.

This study investigates the use of geopolymer technology as an alternative for the management of mine tailings, which is a serious environmental problem in mining environments including that of Arequipa region of Peru. In this study, the mixture of stabilized mine tailings with different percentages of binders (metakaolin and pumice) and their impact on the mechanical, microstructural, and toxicological properties of the synthesized geopolymers were analyzed. The ratios of mine tailings to binder material varied between 100/0 and 0/100. The activation was carried out with an alkaline solution of sodium hydroxide (10M) and sodium silicate (modulus 2.5). 50 mm cubic specimens were fabricated, and 7 mixtures with 3 replicates each were evaluated. The evaluations included compressive strength at 7, 14, 28, and 56 days of curing, chemical analysis by X-Ray Diffraction (XRD) and Fourier Transform Infrared Spectroscopy (FT-IR), microstructural characterization by Scanning Electron Microscopy (SEM/EDS), thermal behavior by thermogravimetry and differential thermal analysis (TGA/DTA) between 40°C and 1000°C, and toxicological tests by the Toxicity Characteristic Leaching Procedure (TCLP, EPA 1311) to determine the efficiency of immobilization of toxic metals. The results showed good mechanical strength, reaching 25 MPa at 7 days of curing, high microstructural stability with an average pore size of 7.21 μm, and good efficiency in the immobilization of heavy metals in geopolymers composed of 60% - 40% and 70% - 30% of the mine tailings - binders ratio, as the concentrations of As, Cd, Pb, Hg were below the established thresholds, acquiring the classification of non-hazardous materials. Geopolymers with 30 to 50% binder showed good mechanical behavior, microstructural stability, and high efficiency in the immobilization of heavy metals, complying with current regulations. Therefore, these geopolymers are suitable for various applications and in different environmental conditions.

An innovative concrete that incorporates the advantages of self-compacting concrete with geopolymer is called self-compacting geopolymer concrete. The objective of this study was the Manufacturing of M30-grade self-compacting geopolymer concrete by adding industrial materials like fly ash (FA), ultrafine ground granulated blast furnace slag (UFGGBS), and silica fume (SF) as minerals. The disposal of these industrial wastes can be substantially overcome, as they lead to land pollution. The fixed powder content was 500 kg/m³. A mixture of sodium silicate (Na₂SiO₃) and sodium hydroxide (NaOH) created an alkaline solution that activated the cementitious binders. In this study, slump flow, L-box, V Funnel, T50 V Funnel, and J ring tests were carried out to determine the fresh qualities of the concrete. These tests were conducted under the regulations for self-compacting concrete provided by EFNARC (2005). To improve the flexural strength of the SCGC, 1.5 % glass fibre was added. This study illustrates how an artificial neural network (ANN) model can determine the concrete mix proportion. The characteristics of SCGC, both fresh and hardened properties test were investigated for molarities of 8, 10, and 12. The microstructural outcomes were determined using Fourier-transform infrared spectroscopy (FT-IR), scanning electron microscopy (SEM), and X-ray diffraction (XRD).

The sensitivity of macroscopic mechanical and thermal properties of grey cast iron is computationally investigated for a variety of graphite microstructures over a wide temperature range. In order to represent common graphite microstructures according to DIN EN ISO 945-1, a synthetic approach is used to algorithmically generate simulation domains. The developed mechanical and thermal model is applied in a large simulation study. The study includes statistical volume elements of the graphite microstructures classes GG-15 and IA2 to IA5, with 10 v.-%, 11 v.-% and 12 v.-% graphite, respectively, for a temperature range from 20 °C to 750 °C. Homogenized macroscopic quantities such as the Young's moduli, Poisson's ratios, yield strengths and thermal conductivities are predicted for the different microstructure classes by applying simulation and data analysis tools of the research data infrastructure Kadi4Mat.

Additive manufacturing processes offer various options to fabricate metal parts, which show numerous ecological and technological advantages compared to formative and subtractive manufacturing methods. Due to quick availability and high accuracy, they are particularly suitable to produce complex prototypes. Metal fused deposition modeling is a relatively new material extrusion additive manufacturing technique based on the widely used fused filament deposition process. This study focuses on the Inconel 625 metal filament from Markforged Inc., it consists of a mixture of metal powder and a binder system, the latter being removed during washing and sintering. In this article, the mechanical properties of printed and sintered Inconel were investigated using tensile testing specimens with three different infill patterns, solid, triangular, and gyroid, printed in flatwise and upright direction. In addition, investigations into the dimensional accuracy of the printed specimens and the sintering shrinkage were carried out. The results showed that neither the dimensional accuracy nor the sintering shrinkage was significantly influenced by the printing orientation. In the context of lightweight engineering, the structures proofed beneficial especially within the elastic region. Generally, triangular infill patterns resulted in higher stiffness, while gyroids led to more ductile specimens. A mass-related evaluation of tensile testing elucidates that with aid of the infill structures weight savings of 40 % resulted in mechanical performance decreased by only 20 % on average.

Although a lot of research has been carried out on hand sanitizer as an effort to prevent Covid-19, there is still limited research on non-alcoholic hand sanitizer lotion from the brown algae Scytosiphon lomentaria (S. lomentaria) as a raw material that provides antibacterial effects and maintains healthy skin. Therefore, this study aimed to analyze microbial inhibitory ability, physical and chemical characteristics of hand sanitizer lotion made from S. lomentaria algae. S. lomentaria powder was tested for phytochemicals, total phenolic content, free radical scavenging activity (IC50), and antibacterial tests. S. lomentaria slurry was prepared by adding distilled water (1:1) for lotion preparations in four treatment groups, such as normal control (lotion base without adding algae), lotion with the addition of algae 20%, 30%, and 40%. The lotion preparations for each treatment group were tested for antibacterial activity of Staphylococcus aureus and Escherichia coli, phytochemicals, pH, adhesion, spreadability, homogeneity, emulsion type, and hedonic. S. lomentaria powder contains bioactive polyphenolic compounds with a total phenolic content of 117.70±1.40 mg GAE/g dry weight and an IC50 value of 455±3.4 ppm, while lotion with the addition of S. lomentaria contains polyphenols and saponins The best treatment was shown by 40% S. lomentaria hand sanitizer lotion with inhibition of 6.30 ± 0.64 mm E. coli, 6.85 ± 1.12 mm S. aureus, hedonic test for color, texture and absorption with likes to likes very much level, neutral pH, greenish-white color, O/W emulsion type, high adhesion, homogeneous, and easily absorbed by the skin. This research can be an alternative reference in making non-alcoholic hand sanitizer lotion that is safe for the skin.

This work addresses the analysis and characterization of deadlocks in discrete-event systems modeled by labeled Petri nets (LPNs) with undistinguishable and unobservable transitions. To provide a solution for the notorious problem, it is essential to present an effective characterization such that deadlock control and synthesis are technically and methodologically possible. To this end, we introduce the notion of dangerous implicit vectors (DIVs) which implicitly threaten the system deadlock-freedom. The set of dead markings is divided into two subsets: dead basis markings (DBMs) and dangerous implicit markings (DIMs). An algorithm is designed to compute the sets of DIVs and DIMs at a given basis state of a system. Moreover, by virtue of linear algebraic equations, we formulate sufficient conditions to identify the existence of blocking markings in an LPN. Finally, an algorithm is developed to construct an observed graph that is a compact representation of the reachability graph of a Petri net with respect to the existence of dead reaches. At the end of this paper, experiment results that illustrate the correctness and effectiveness of the reported solution are presented.

Current paper is aiming to show the obtained results in manufacturing and characterization of graphite-based and metal composite materials suitable to be used in high voltage applications of automotive and/or aviation field. Thus, 4 types of materials have been processed and tested in order to assess their suitability to be used as current collector material for electric engines. The novelty of this work is the presentation of the new innovative technological process for obtaining the carbon/metal composite material used in the manufacture of sliding contacts for current collector heads, as well as the characteristics obtained for this material. All 4 obtained materials have been characterized from structural, mechanical and functional point of view and the most suitable of them has been chosen to be further developed by the end beneficiary.

Reducing CO2 emissions is urgently needed to slow down the impacts of climate change. CO2 capture using an amine solution has been developed and implemented on pilot and commercial scales. However, amine scrubbing, in particular, produces a lot of degraded solvent as waste and is energy intensive. Solid sorbents have been called to overcome those drawbacks. In this work, waste biomass-derived carbon materials were developed and tested for CO2 capture and conversion. Advanced thermal chemical processes i.e. hydrothermal and pyrolysis were applied to produce materials from agri-food waste such as soybean and okara. It was found that the number of functional groups (-C=O and -OH) in activated carbon appears in the synthesized materials, implying the generation of surface oxygenated groups. Preliminary results showed that the synthesized activated carbons are obtained with good yields, and a relatively high surface area, which may be applied as CO2 adsorption materials to solve the CO2 emission problems.

Saikosaponin (SS) a is a compound with various pharmacological properties and easily degraded into SSb1 and SSg in acid condition. In present work another two new degradation products of SSa formed under acid hydrolytic condition were detected and isolated by analytical and semi-preparative liquid chromatography technology, furthermore their structures were characterized as hydroxyl-saikosaponin a and SSb2 by spectral analysis, which is not only essential in stability-indicating method development and validation but also could be used as a worst case to assess the analytical method performance of SSa. Moreover their structural transformation pathways were also proposed.

Rationale: Post-hepatectomy liver failure (PHLF) remains a significant risk for patients undergoing partial hepatectomy (PHx). Reliable prognostic markers and treatments to enhance liver regeneration are lacking. Plasma nanoparticles, including lipoproteins, exosomes, and extracellular vesicles (EVs), can reflect systemic and tissue-wide proteostasis and stress, potentially aiding liver regeneration. However, their role in PHLF is still unknow. Methods: Our study included 9 patients with hepatocellular carcinoma (HCC) undergoing PHx: 3 patients with PHLF, 3 patients undergoing the Associating Liver Partition and Portal vein Ligation for Staged hepatectomy (ALPPS) procedure and three matched controls without complications after PHx. Patient plasma was collected before (PRE), 1 and 5 days (POD1, POD5) after PHx. EVs were isolated by ultracentrifugation and extracted proteins subjected to quantitative mass spectrometry using a super-SILAC mix prepared from primary and cancer cell-lines. Results: We identified 2625 and quantified 2570 proteins in EVs in PHx patients. Among these, 53 proteins were significantly upregulated and 32 were downregulated in patients with PHLF compared to those without PHLF. Furthermore, 110 proteins were upregulated and 78 were downregulated in PHLF compared to patients undergoing ALPPS. The EV-proteomic signature in PHLF indicates significant disruptions in protein translation, proteostasis, intracellular vesicle biogenesis, as well as alterations in proteins involved in extracellular matrix (ECM) remodeling, metabolic and cell cycle pathways, present already before PHx. Conclusion: Longitudinal proteomic analysis of EV´s circulating in human patient plasma undergoing PHx uncovers proteomic signatures associated with PHLF which reflect dying hepatocytes and endothelial cells and are present before PHx already. Our results support EVs as potential biomarkers and therapeutic targets for liver regeneration and failure.

Continuous-wave photocathode guns are capable of delivering electron beams with high repetition rates and high average currents. However, they are limited by relatively low accelerating gradients and cathode fields. This limitation leads to a larger beam size at the gun exit due to space charge forces, making the beam more sensitive to optical aberrations and posing challenges for low-emittance electron beam transmission. This paper focuses on the aberrations induced by multipole fields. We analyze the effects of quadrupole, sextupole, and higher-order fields on beam profile and transverse emittance and propose a beam-based method for the rapid characterization and correction of these multipole fields. Furthermore, we present an experimental study conducted on the DC-SRF-II photocathode gun equipped with dedicated correctors. Both simulation and experimental results demonstrate that our approach effectively mitigates beam aberrations caused by multipole fields, resulting in improved beam symmetry and reduced emittance.

The relentless advancement and integration of mechanization and intelligence within the coal mining industry, combined with the increasing depths of mining operations, necessitate significantly higher safety standards. This necessity arises due to the increasingly complex geological and coal seam conditions encountered as mining operations delve deeper into the earth. Traditionally, 3D seismic exploration technology has been fundamental in ensuring both operational efficiency and safety in the coal mining sector. However, despite its critical role, this technology still has limitations in detecting and characterizing small-scale geological structures which can pose substantial risks if not accurately identified and mitigated. To address these challenges, this paper introduces a sparsity-constrained adaptive hard thresholding algorithm designed to tackle the spectral inversion optimization problem with an norm constraint for the enhanced retrieval of reflection coefficients, thereby establishing a comprehensive workflow for enhancing seismic data resolution through compressed sensing spectral inversion. Real data validation has demonstrated that this method significantly enhances the resolution of seismic data while maintaining the amplitude integrity and fidelity of the original signals. This improvement allows for a more detailed and accurate characterization of small-scale geological features, which are critical in identifying and mitigating potential hazards within coal mining operations, thus offering robust support for the implementation of more effective safety protocols and disaster prevention strategies in coal mines.

This study explores the development and characterization of ceramic rod reinforced TWIP (Twinning Induced Plasticity) steel matrix composites, fabricated using a lost foam casting process. The incorporation of ceramic rods aims to enhance the mechanical properties of TWIP steel, which is known for its excellent plasticity. Mechanical testing demonstrated a significant improvement in flexural strength and ductility, with the composite exhibiting over double the strength of the unreinforced TWIP steel. Heat treatment at 500°C for 60 minutes further enhanced these properties, increasing the composite's flexural strength to 1023 MPa and improving its ductility. The observed improvements are attributed to the synergistic effects of the hard ceramic reinforcement and the ductile matrix, as well as the microstructural modification conferred by heat treatment. These findings suggest that ceramic rod reinforced TWIP steel composites are promising materials for applications requiring a combination of high strength and ductility.

Cement paste backfill (CPB) is an effective waste management method allowing the storage of fine process tailings into underground mined-out voids. CPB performance generally depends on the sulfur content of the tailings and the type of binder. In recent years, there has been an in-creasing trend on the use of alkali-activated slag (AAS) to improve the performance properties of CPB. This study focuses on the ultrasonic and microstructural investigation of the effect of slag fineness on the mechanical, geochemical and durability properties of CPB made up of AAS (AAS-CPB) over 360 days. In this scope, AAS-CPB samples were prepared at three different fineness (3100-4650-6300 cm2/g). Fineness of slag significantly improved the early age- and long-term strength (~2.3 fold and ~6.6 fold, respectively) of CPB. However, further increase of slag fineness may have adverse effect on CPB microstructure and strength in the long term. Ultrasonic pulse velocity monitoring displayed very high relation with the strength evolution and durability assessment of CPB. Slag fineness at a degree was seen to improve the pore structure evolution of AAS-CPB. Microstructural studies are in good agreement with the geochemical and durability behavior of AAS-CPB. Microstructural and ultrasonic findings suggest that while slag fineness enhances the mechanical properties of AAS-CPB, further increase of the fineness of slag has no additional important technical advantages.

: In the automotive industry, high-strength plates have been increasingly used to reduce the vehicle body weight due to stringent regulations on fuel economy and safety. Such plates achieve tensile strengths as high as 1.5 GPa owing to the hot-stamping process. However, these plates suffer from scale generation and surface decarburization because of the surface oxidation of the material. Recently, studies on materials subjected to high-frequency induction heating have reported strength improvement owing to the coil shape and cooling method. This study presents the surface temperature changes, mechanical properties, and microstructures of boron steels subjected to longitudinal heating, which uses eddy currents generated from high-frequency induction heating. The surface temperature data were analyzed under different high-frequency induction heating powers (15, 18, 21, 24, 27, and 30 kW) and distances from the specimen (6, 9, and 15 mm). The mechanical properties and microstructures were also analyzed in different high-frequency induction heating coil directions. The correlations between the high-frequency induction heating power and the distance from the specimen with the maximum tensile strength were determined.

The AREB/ABF (ABA response element binding) proteins in plants are vital for plant stress responses, but the understanding of AREB/ABFs in orchid species, an important traditional medicinal and ornamental plants, is limited. Here, twelve AREB/ABF genes were identified within three orchids’ complete genome and classified into three groups (groups I, II, and III) via a phylogenetic analysis, which was further supported by the analysis of their conserved motifs and gene structures. The cis-elements analysis showed that hormone response elements followed by light and stress responses were widely rich in AREB/ABFs. A prediction analysis of orchid ABRE/ABF-mediated regulatory network was further constructed through cis-regulatory elements (CREs) analysis of their promoter regions and revealed that several transcriptional factor (TF) gene family were abundant as the potential regulators for orchid AREB/ABFs. Expression profile analysis based on public transcriptomic data showed that most AREB/ABF genes have distinct tissue-specific expression patterns in orchid plants. Additionally, DcaABI5 as the homolog of ABA INSENSITIVE 5 (ABI5) from Arabidopsis was selected for further analysis. The results showed that Arabidopsis transgenic overexpressing DcaABI5 could rescue the ABA insensitive phenotype in the mutant abi5. Collectively, these findings will provide valuable information on AREB/ABF genes in orchids.

Most of the mid-high permeability sandstone oilfields in China have entered the ultra-high water cut stage, accompanied with the highly-dispersed residual oil, and the control effect of mi-cro-heterogeneity on the residual oil is increasingly prominent. Understanding the microscopic characteristics of pore structural and its evolution during the long-term waterflooding is critical for enhancing the accuracy and efficiency of oil field exploitation. While the previous insights paid more attention to the geometrical and morphological features of pore structure and ignores the relation of pore structure with the fluid flow capacity. In this study, we propose a microscopic pore structure classification method considering pore size and local permeable capacity, which realizes the physical classification and quantitative evaluation of pore structure characteristics for different permeability rocks. The micro-pore structure is classified into 6 types based on the key evaluation parameters of pore diameter and flow flux area. By taking six mid-high permea-bility sandstone core samples from Daqing oilfield in China, a series of long-term waterflooding experiments are carried out and the interior pore structure was captured using high precision CT scanning technique. The results reveals that high-permeability reservoirs exhibit concentrated pores diameters and finer throats, whereas mid-permeability reservoirs exhibit smaller pores and throats in greater quantity. With the increase of water injection volumes, the permeable ca-pacity and connectivity of the high-connectivity pore space in ultra-high- and high-permeability reservoirs are enhanced, and in mid-permeability reservoirs, the micro-heterogeneity intensifies the increase in low-connectivity small pores. These findings provide new insights for the micro-scopic heterogeneity and a solid theoretical basis for investigating the occurrence of microscopic residual oil and optimising enhanced oil recovery strategies at the late stage of ultra-high water cut.

A total of 27 microsatellites markers , scattered all over the genom of barley, were used for characterization,and diversity analysis in 33 barley (Hordeum vulgare L.) accessions and cultivars of Algeria.Over the 27 genetic loci studied, 110 alleles were identified with a mean of 4.1 alleles per locus and the average polymorphism information content (PIC) of 0.46,the marker Ebma0806 showed the greatest value of PIC with 0.83.Genetic diversity at 27 microsatellite loci varied from 0 to 0.84 (Mean=0.50) for 33 Algerian cultivars. The genetic distance among the cultivars ranged from 0.2 to 0.85. Cluster analysis and principal coordinate analysis (PCoA) based on the SSR data clearly differentiate the all genotypes studied.

The criteria of “Distinctness, Uniformity and Stability” as well as a high "overall quality index” are used to register the Italian modern varieties to the national register. Differently, local conservation varieties can be certified under different EU Directives having, as overall objective, the preservation of biodiversity and the containment of genetic erosion. In recent years, products derived from an-cient grains are perceived to be healthier and more sustainable by consumer, especially in Italy, with consequent higher market prices. Ancient tetraploid wheat varieties registered in the national reg-ister of conservation varieties are 28, 24 of which are Sicilian. They are supposed to have a wide genetic variability compared to modern ones, making them vulnerable of fraud because they are difficult to trace. It is therefore important to have tools able to discriminate the autochthonous Si-cilian varieties. This can be done by gluten proteins composition, which also gives information on the technological properties of derived products. Fifty-one accessions belonging to 22 ancient va-rieties of Sicilian tetraploid (mostly durum) wheat were analyzed. Although a wide intra-accession and intra-varietal variability was assessed, the gliadin pattern of bulks of seeds belonging to each variety was discriminatory. Moreover, differences in technological attitudes were found between landraces. This paves the way to use gluten protein patterns for traceability allowing local farmers and producers to valorize their products and assure consumers about the transparency of the entire supply chain.

The Bax inhibitor-1 (BI-1) gene family, which is required for plant growth, development, and stress tolerance, remains largely unexplored in cauliflower. In this study, we identified and characterized cauliflower BI-1 family genes. On the basis of aligned homologous sequences and collinearity with Arabidopsis genes, we identified nine cauliflower BI-1 genes, which encoded proteins that varied regarding length, molecular weight, isoelectric point, and subcellular localization (i.e., Golgi apparatus, plasma membrane, cell membrane, and chloroplast). Phylogenetic analyses detected evolutionary conservation and divergence among these genes. Ten structural motifs were identified, with Motif 5 crucial for inhibiting apoptosis. According to the cis-regulatory elements in their promoters, these genes likely influence hormone signaling and stress responses. Expression profiles among tissues highlighted the diversity in the functions of these genes, which were significantly expressed in the silique and root. Focusing on BobBIL4, we investigated its role in brassinosteroid (BR)-mediated root development and salt stress tolerance. BobBIL4 expression levels increased in response to BR and salt treatments. The functional characterization of this gene in Arabidopsis revealed it enhances root growth and salinity tolerance. These findings provide insights into BI-1 gene functions in cauliflower, while also highlighting the potential utility of BobBIL4 for improving crop stress resistance.

In Mexico viticulture represents the second source of employment in the agricultural area after the fruit and vegetable sector. In developed countries, remote sensing is widely used for vineyard monitoring, however, this tool is barely used in developing countries of Iberoamerica. In this re-search, our overall objective is to characterize two vineyards in the state of Queretaro (Mexico) using Sentinel-2 and meteorological data, specifically spectral and thermal indices. Results showed that spectral indices obtained from Sentinel-2 bands have characterized adequately the phenolog-ical evolution of the different varieties of the vineyards. The Modified Soil-Adjusted Vegetation Index (MSAVI) was adequately used to discriminate the first stages of vineyards, while the Nor-malized Difference Vegetation Index (NDVI) was useful to monitor vineyards during the rest stages of vineyards. Thermal indices have shown that the best grape varieties were those that can adapt to both cooler and warmer temperatures, have a reasonable ripening period, and can produce wines with balanced acidity and flavors. In conclusion, the combination of meteorological (including thermal indices) and remote sensing data (NDVI and MSAVI) provide information for choosing the suitable grape variety for this region.

Dearth of information on extent of genetic variability in cassava limits the genetic improvement of cassava in Sierra Leone. This study aimed at assessing the genetic variability and relationships within 103 cassava genotypes using agro-morphological and culinary markers. A field trial was conducted in the School of Agriculture and Food Sciences research site. The experiment was laid in an augmented randomized block design. Morphological classification based on qualitative and quantitative traits categorized the germplasm into three different groups. A total of ten principal components (PCs) in the qualitative and six PCs in the quantitative trait sets accounted for 66.74% and 67.27% of the total genetic variation, respectively. Traits with significantly strong and positive correlations included presence of fruit (PFRT) and presence of seed (PSE)(r = 0.86***),root yield per plant (RYPP) and number of storage root (NSR) (r = 0.76***), RYPP and number of commercial root (NCR) (r = 0.68***), length of leaf lobe (LLL) and width of leaf lobe (WLL) (r = 0.66***),and between NSR and NCR (0.84***). Cooking time, cooking percentage, texture, mealiness, taste and aroma varied widely among the accessions. Findings established that the cassava germplasm possess useful genetic variability that could be exploited through selection for short term release programme, genetic conservation of valuable germplasm and genetic improvement of the crop.

Clostridioides difficile is a Gram-positive pathogen known for its toxin production and spore formation. It is primarily responsible for most cases of antibiotic-associated diarrhea. Bacterial persisters are a small subset of the population that exhibits transient tolerance to bactericidal substances, and they are of significant medical concern due to their association with the emergence of antibiotic resistance and difficult-to-treat chronic or recurrent infections. Vancomycin, the predominant antibiotic utilized in the management of C. difficile infection, is extensively applied in the realm of clinical practice. Previous studies have demonstrated a persister-like phenotype with treatments involving this antibiotic. However, the mechanism in C. difficile remains largely unknown, primarily due to the challenge of isolating this small population at any given time. To better characterize C. difficile persister cells, we present a study that enables the enrichment and characterization of persister cells from bacterial cultures in both exponential and stationary phases. Moreover, we could differentiate between triggered (induced by antibiotics, such as vancomycin) and spontaneous (stochastic) persister cells. Additionally, we observed the involvement of toxin-antitoxin systems and Clp proteases in persister cell formation.

During the last years there has been a high interest in the development of new purely-organic single-component conductors. Very recently, we have reported a new neutral radical conductor based on the perchlorotriphenylmethyl (PTM) radical moiety linked to a monopyrrolo-tetrathiafulvalene (MPTTF) unit by a -conjugated bridge (1). Interestingly, this system behaves as a semiconductor with high conductivity and small energy gap under high pressure. With the aim of developing a new material with improved conducting properties, we have designed and synthesized the radical dyad 2 which was functionalized with an ethylenedithio (EDT) group in order to improve the intermolecular interactions of the TTF subunits. The physical properties of the new radical dyad 2 were studied in detail in solution to further analyze its electronic structure as well as its potential use as radical conductor in the solid state.

Calcium phosphates and manganese phosphates play a significant role in biomedical and engineering applications, and these compounds are both synergistic. These compounds could have great potential for use in different applications, particularly as precursors of biomaterials. Therefore, the aim of this study was to explore the effect of the gradual replacement of Ca2+ with Mn2+ on the phase composition and crystal structure of brushite (CaHPO4·2H2O), which could be useful for the production of Mono- and Biphasic Ca1−xMnxHPO4·nH2O Compounds. In order to prepare the starting solutions required for this study, Ca(NO3)2·4H2O, (NH4)2·HPO4, and Mn(NO3)2·4H2O were used at various molar concentrations. Afterwards, the Ca1−xMnxHPO4·nH2O compounds were prepared using dissolution and precipitation methods. These compounds were characterized using XRD, SEM, FT-IR, XPS, and TGA techniques. The findings revealed that Mn substituted Ca partially at low Mn/Ca molar ratios, 0.25, and Mn doping increased the unit cell of CaHPO4·2H2O. The produced biphasic compound was composed of monoclinic CaHPO4·2H2O and nanostructured orthorhombic MnHPO4·(H2O)3 after a continuous increase in the Mn/Ca molar ratio to 1.5. When the Ca/Mn molar ratio was above 1.5, a monophasic compound of the MnHPO4·(H2O)3 phase was formed. The MnHPO4·(H2O)3 compound was successfully prepared for the first time using this dissolution-precipitation method. It was also established that the Mn/Ca ratio of the starting solution can be modified to produce CaHPO4·2H2O and MnHPO4·(H2O)3 phases with specific weight percent compositions.

We present an analysis of high-resolution, near-infrared (NIR) spectra relative to the solar transit of Venus of 5-6 June 2012, as observed with the Facility Infrared Spectropolarimeter (FIRS) at the Dunn Solar Telescope in New Mexico. These observations offer the unique opportunity to probe the upper layers (between ∼84 and 150 km in altitude) of a thick, CO2-dominated atmosphere with the transmission spectroscopy technique – a proxy for future studies of highly-irradiated atmospheres of Earth-sized exoplanets. We were able to visually identify absorption lines from the two most abundant CO2 isotopologues, and from the main isotopologue of CO in the retrieved spectrum of Venus. Furthermore, we perform a cross-correlation analysis of the transmission spectrum using transmission templates generated with petitRADTRANS. With the cross-correlation technique, it was possible to confirm detections of both CO2 isotopologues and CO. Additionally, we retrieve a cross-correlation signal for O3 on Venus. We demonstrate the feasibility of high-resolution, ground-based observations to study the chemical inventory of planetary atmospheres, employing techniques commonly used in exoplanet characterization.

Electrospun ultrathin fibers based on binary compositions of polylactide (PLA) and poly(ε-caprolactone) (PCL) with different ratios of polymer components from 0/100 to 100/0 wt. % were studied. Using a combination of thermal (DSC) and relaxation (EPR) measurements, the effect of biopolymers content on the characteristics of the crystal structure of PLA and PCL and the diffusive rotational mobility of the stable TEMPO radical in the amorphous regions of PLA/PCL compositions was shown. It was revealed that after PLA and PCL blending, significant changes in the degree of crystallinity of PLA, PCL segmental mobility, sorption capacity of the radical as well as activation energy of rotational diffusion in the amorphous regions of PLA/PCL composition are observed. The characteristic region of biopolymers’ composition from 50/50 to 30/70 % PLA/PCL blends ratio was found, where the inversion transition of PLA from dispersive medium to dispersive phase where an inversion transition is assumed when the continuous medium of the PLA transforms into a discrete phase. The performed studies made it possible for the first time to carry out a comprehensive analysis of the effect of the system component ratio on the structural and dynamic characteristics of the PLA/PCL film material at the molecular level.

In this study, carbon blocks were fabricated using isotropic coke and coal tar pitch as raw materials, with a variation in pressure during cold isostatic pressing (CIP). The CIP pressure was set to 50, 100, 150, and 200 MPa, and the effect of the CIP pressure on the mechanical and electrical properties of the resulting carbon blocks was analyzed. Microstructural observations confirmed that after the kneading, the surface of isotropic coke was covered with the pitch components. Subsequently, after the CIP, granules, which were larger than isotropic coke and the kneaded particles, were observed. The formation of these granules was attributed to the coalescence of kneaded particles under the applied pressing pressure. This granule formation was accompanied by the development of pores, some remaining within the granules, while others were extruded, thereby existing externally. The increase in the applied pressing pressure facilitated the formation of granules, and this microstructural development contributed to enhanced mechanical and electrical properties. At a pressing pressure of 100 MPa, the maximum flexural strength was achieved at 33.3 MPa, and the minimum electrical resistivity was reached at 60.1 μΩm. The higher the pressing pressure, the larger the size of the granules. Pores around the granules tended to connect and grow larger, forming crack-like structures. This microstructural change led to degraded mechanical and electrical properties. The isotropic ratio of the carbon blocks obtained in this study was estimated based on the coefficient of thermal expansion (CTE). The results confirmed that all carbon blocks obtained proved to be isotropic. In this study, a specimen type named CIP-100 exhibited the best performance in every aspect as an isotropic carbon block.

Epitaxial lithium ferrite (LiFe5O8) films with different thicknesses have been successfully fabricated on SrTiO3 (001) substrates by magnetron sputtering deposition technique. The microstructural and magnetic properties are characterized by advanced transmission electron microscope and magnetic measurement device. It was found that the formation of structural defects can be influenced by the thickness of the film. Apart from the misfit dislocations, the orientation domains form in thinner film and twin boundaries appear in thicker film, respectively, contributing to the misfit strain relaxation in the heterosystem. The magnetic measurement shows that the thinner films have enhanced magnetization and a relatively lower coercive field compared with the thicker films containing the antiferromagnetic twin boundaries. Our results provide a way for tuning the microstructure and magnetic properties of lithium ferrite films by changing the film thickness.

Coxsackievirus A6 (CV-A6) has emerged as the predominant causative agent of hand, foot, and mouth disease (HFMD) in young children. Since the declaration of coronavirus disease 2019 (COVID-19) as a global pandemic, the incidence of infectious diseases, including HFMD, has decreased markedly. When social mitigation was relaxed during the COVID-19 pandemic in 2022, re-emergence of HFMD was observed in Gwangju, South Korea, and seasonal characteristics of the disease appeared to have changed. To investigate the molecular characteristics of enterovirus (EV) associated with HFMD during 2022, 277 specimens were collected. Children aged under 5 years accounted for the majority of affected individuals. EV detection and genotyping were performed using real-time RT-PCR and nested RT-PCR followed by sequence analysis. EV detection rate was found to be 82.3%, and the main genotype identified was CV-A6. Sixteen CV-A6 samples were selected for whole genome sequencing. According to phylogenetic analysis, all CV-A6 strains from this study belonged to the sub-genotype D3 clade based on VP1 sequences. Analysis of 3D polymerase phylogeny showed that only the recombinant RF-A group was identified. In conclusion, circulating EV types should be continuously monitored to understand pathogen emergence and evolution during the post-pandemic era.

Pore structure characterization and fractal analysis have great significance for understanding and evaluating tight limestone reservoirs. In this work, the pore structure of tight limestone is characterized combined with low-temperature nitrogen adsorption (LTNA) and low-field nuclear magnetic resonance (NMR), and the fractal dimension of tight limestone pore structure is discussed based on LTNA and NMR data. The results indicate that the pores of tight limestone have H3 and H4 types, the pore size distribution (PSD) of H3 type is a wave distribution ranging from 2 to 10 nm, and the PSD of H4 type is a unimodal distribution ranging from 2 to 10 nm. The transverse relaxation time (T2) spectrum of tight limestone shows single peak (DF), double peak (SF) and three peak (TF), and the T2 spectrums for micropores, mesopores and macropores range from 0.1 to 10 ms, from 10 to 100 ms, and greater than 100 ms, respectively. The LTNA fractal dimension of tight limestone (DL) ranges between 2.4446 and 2.7688, with an average of 2.5729, and the NMR fractal dimensions of micropores (DNMR1), mesopores (DNMR2) and macropores (DNMR3) are distributed between 0.3744 to 1.1293, 2.4263 to 2.9395 and 2.6582 to 2.9989, respectively. Moreover, there is no correlation between fractal dimension and permeability and porosity, a negative correlation between DL and average pore radius, a positive correlation between DL and specific surface area, and a positive correlation between DNMR2 and DNMR3 and micropore content, while DNMR2 and DNMR3 are negatively correlated with the content of mesopores and macropores.

Polypyrrole (PPy)-capped caped silver nanowire (Ag NW) nanomaterials (core–shell rod-shaped Ag NW@PPy) were synthesized suing a one–port suspension polymerization technique. The thickness of PPy layer on the 50-nm-thickness/15-μm-length Ag NW was effectively controlled to 10, 40, 50, and 60 nm. Thin films cast from one-dimensional conductive Ag NW@PPy formed a three-dimensional (3-D) conductive porous network structure and provided excellent electrochemical performance. The 3-D Ag NW@PPy network can significantly reduce the internal resistance of the electrode and maintain structural stability. As a result, a high specific capacitance of 625 F/g at a scan rate of 1 mV/s was obtained from the 3-D porous Ag NW@PPy composite film. The cycling performance over a long period exceeding 10,000 cycles was also evaluated. We expect that our core–shell-structured Ag NW@PPy composites and their 3-D porous structure network films can be applied as electrochemical materials for the design and manufacture of supercapacitors and other energy storage devices.

To address the requirements of sonar imaging, such as high receiving sensitivity, wide bandwidth, wide receiving angle, an AlN PMUT with an optimized ratio of 0.6 for the piezoelectric layer diameter to backside cavity diameter is proposed in this paper. A sample AlN PMUT is designed and fabricated with SOI substrate-based bulk MEMS process. The characterization test result of the sample demonstrates a -6 dB bandwidth of approximately 500 kHz and a measured receiving sensitivity per unit area of at 1.37 V/μPa/mm2, which significantly surpasses the performance of previously reported PMUTs. The -6 dB horizontal angles of the AlN PMUT at 300 kHz and 500 kHz are measured 68.30° and 54.24°, respectively. To achieve an accurate prediction of its characteristics when being packaged and assembled in a receive array, numerical simulations with the consideration of film stress are conducted. The numerical result shows a maximum deviation of ±7% in the underwater receiving sensitivity across the frequency range of 200 kHz to 1000 kHz and a deviation of about 0.33% in the peak of underwater receiving sensitivity comparing to the experimental data. By such good agreement, the simulation method reveals its capability of providing theoretical foundation for enhancing the uniformity of the AlN PMUTs in future studies.

Biomaterials are the basis for the development of medicine because they allow safe contact with a living organism. The aim of this work was to produce innovative oxide layers with a porous microstructure on the surface of commercially pure titanium Grade 4 (CpTi G4), and to characterize their properties as drug carriers. Anodization of the CpTi G4 subjected to mechanical grinding and electrochemical polishing was carried out in a solution of 1M ethylene glycol with the addition of 40 g of ammonium fluoride at a voltage of 20 V for 2, 18, 24 and 48 hours at room temperature. It was found that the longer anodization time, the greater the number of pores formed on the CpTi G4 surface as revealed by FE-SEM method, and the greater the surface roughness determined in profilometric tests. As the anodizing time increases, the amount of the drug in the form of gentamicin sulfate incorporated into the resulting pores decreases. The most favorable drug release kinetics profile determined by UV-VIS absorption spectroscopy was found for the CpTi G4 anodized for 2 h making them the best choice when it comes to the drug carrier allowing full use of the therapeutic dose of the drug.

We investigated the micro-threaded stem taper surface and the impact on premature failures, aseptic loosening, and infection. We have focused on the fretting, and crevice corrosion of micro-threaded tapers, as well as the characterization of microstructure and surface properties of two new and three retrieved Zweymüller stem tapers of cementless hip endoprostheses selected from a set of 45 stems. The retrievals examined were those in which the sole source of modularity with a metallic component was the head-stem taper interface between the Ti alloy taper stem and the ceramic head. To determine the surface chemistry and microstructures of both new and retrieved hip endoprostheses stem taper titanium alloy, scanning electron microscopy (SEM) was employed for morphological and microstructural analyses. At the same time, energy dispersive spectroscopy (EDS) was utilized for characterizing chemical element distribution, and electron backscattered diffraction (EBSD) was used for phase analysis. The micro-threated stem taper’s roughness for different manufacturers was investigated using an optical profilometer. Standard roughness pa-rameters Ra (average surface roughness) and Rz (mean peak to valley height of the roughness pro-file) were used in this investigation.Additionally, profile depth and peak spacing for different samples were investigated. The surface roughness results indicate no significant difference in roughness associated with varying survivorship times, ranging from 3 to 239 months, and across different manufacturers. Electrochemical studies revealed no fretting corrosion in retrieved stem tapers (ceramic head) that prematurely failed due to aseptic loosening after 239 months, infection after 3 months, and low-grade infection after a 32-month lifetime. Therefore, three retrieved ta-pers and two new ones for comparison underwent potentiodynamic measurements in Hank’s so-lution to ascertain the corrosion rate of new and retrieved stem taper surfaces. The results show a low corrosion rate for both new and retrieved samples that failed prematurely due to aseptic loosening. However, the corrosion rate of infected and low-grade infected tapers was higher. In conclusion, our study aligns with existing literature, suggesting that the use of ceramic heads de-creases the problem of taper corrosion and subsequently reduces premature failures in total hip arthroplasty.

The flow stress of face-centered cubic (FCC) metals exhibits a rapid increase near a strain rate of 104 s-1 under fixed strain conditions. However, many existing constitutive models either fail to capture the mechanical characteristics of this plastic deformation or use piecewise strain rate hardening models to describe this phenomenon. Unfortunately, the piecewise models may suffer from issues such as discontinuity of physical quantities and difficulties in determining segment markers, and struggling to reflect the underlying physical mechanisms that give rise to this mutation phenomenon. In light of this, this paper proposes that the abrupt change in flow stress sensitivity to strain rate in FCC metals can be attributed to microstructural evolution characteristics. To address this, a continuous semi-empirical physical constitutive model for FCC metals is established based on the microstructural size evolution proposed by Molinari-Ravichandran and the dislocation motion slip mechanism. This model effectively describes the mutation behavior of strain rate sensitivity under fixed strain, particularly evident in the annealed OFHC. The predicted results of the model across a wide range of strain rates (10-4 − 106 s-1) and temperatures (77 − 1096 K) demonstrate relative errors generally within ±10% of the experimental values. Furthermore, the model is compared to five other models, including Mechanical Threshold Stress (MTS), Nemat-Nasser-Li (NNL), Preston-Tonks-Wallace (PTW), Johnson-Cook (JC), and Molinari-Ravichandran (MR) models. A comprehensive illustration of errors reveals that the proposed model outperforms the other five models in describing the plastic deformation behavior of OFHC. The error results offer valuable insights for selecting appropriate models for engineering applications and provide significant contributions to the field.

The Aspergillus genus comprises fungi that are widely distributed in nature. The Terrei section is particularly important due to its functions in recycling organic matter. Aspergillus hortae is a species from this section that has been isolated from clinical samples, but its role as a pathogenic agent is unclear. In this study, three clinical A. hortae isolates from Colombia, initially identified as A. terreus, were characterised by micro and macro-morphological analysis at 26°C and 37°C. A bioinformatic pipeline was used for molecular typing, which included analysis of whole genome sequences for accurate species identification. Susceptibility assays were also conducted using the microdilution broth method (EUCAST). It was confirmed that this species is intrinsically resistant to Amphotericin B with a minimum inhibitory concentration (MIC) of 2-4 mg/L, and is also thermotolerant. We obtained the in vitro susceptibility profiles for three azole drugs (MIC, 0.25-1 mg/L). The three isolates showed phylogenetic divergence from the reference genome strain. A mutation (M769K) in the MelA ortholog of a hypopigmented isolate, which had the lowest MIC value for AmB (2 mg/L), was identified. This study presents the morphological characterization, molecular typing through whole-genome analysis and identification of susceptibility profiles to azoles and amphotericin B of three clinical isolates of A. hortae from Colombia.

In the present study, a multilayer high barrier thin blown film based on a polybutylene adipate terephthalate (PBAT) blend with polyhydroxyalkanoate (PHA), and composed of four layers, including a cellulose nanocrystals (CNC) barrier layer and an electrospun poly(3-hydroxybutyrate-co-3-hydroxyvalerate) (PHBV) hot-tack layer, was characterized in terms of surface roughness, surface tension, migration, mechanical and peel performance, barrier properties and disintegration rate. The results showed a material with a smooth surface. The overall migration test showed that the material was suitable for its use as a food contact layer. The addition of the CNC interlayer had a significant effect on the mechanical properties of the system, drastically reducing the elongation at break and, thus, the flexibility of the material. However, the material retained its elastic modulus and tensile strength. The CNC coating had a negative impact on the peeling strength, weakening the inherently strong interlayer adhesivity of the electrospun PHBV fibers. The multilayer had a good barrier to water vapor, and especially to oxygen, with its permeance reduced by up to a 90 % when the CNC layer was present. Finally, the monolayer blend film disintegrated in a period of less than 55 days in a laboratory-scale composting experiment, while the multilayer system disintegrated in 60 days. Overall, the multilayer system formed a fully compostable structure with great potential for use in food packaging applications.

Microparticles derived from biomaterials are becoming increasingly popular for various applications, particularly in drug delivery systems. In this study, the water-in-oil (W/O) emulsification-diffusion method was used to create cellulose (C), silk fibroin (SF), and C/SF composite microparticles. We then observed the morphology of all obtained microparticles using scanning electron microscopy (SEM), evaluated their functional groups using attenuated total reflection Fourier transform infrared spectroscopy (ATR-FTIR), and conducted thermogravimetric analysis using a thermogravimetric analyzer (TGA). SEM micrographs indicated that the native SF microparticles have the highest spherical shape with smooth surfaces. With blue dextran, the C microparticle was smaller compared to the native microparticle, while the drug-loaded SF microparticles were bigger than the native microparticle. The morphological surfaces of the C/SF composite microparticles were varied in shape and surface depending on the C/SF ratio used. The spherical shape of the C/SF composite microparticle was increased as SF content increased. Furthermore, the size of drug-loaded C/SF composite microparticles was gradually increased by the SF content. The significant functional groups in the C and SF structures were identified based on the ATR-FTIR data, and a suggestion was made regarding the interaction between the functional groups of each polymer. When compared to both native polymers, the C/SF composite microparticles exhibit improved thermal stability. The C/SF composite microparticle at a 1:3 ratio had the lowest drug release content, whereas the hydrophilicity of the C microparticle affected the highest drug release content. As a result, one crucial factor affecting the medication released from the microparticle is its thermal stability. According to the obtained results, C, SF, and C/SF composite microparticles show promise as delivery systems for drugs with controlled release.

In the perspective of designing complex concentrated alloys (CCAs) for structural applications, sigma (σ) phase is important. It is generally known to be an embrittling phase leading to a degradation in the mechanical properties of CCAs. This necessitates detailed investigations on the evolution of σ phase in these alloys. In the present study, an equiatomic CoCrCuMnNi CCA is chosen, in which σ phase appears at 800°C, as reported in a recent publication [1]. To this end, the present investigation aims at understanding the evolution of this phase so that its presence can be controlled for the purpose of preventing degradation in mechanical properties. In the present work, a vacuum arc melted alloy, after homogenisation (at 400°C for 5h), is heat-treated for different times ranging from 1 to 9h at 800°C followed by water quenching. Extensive characterisation has been carried out using X-Ray Diffraction (XRD) and Scanning Electron Microscopy (SEM) and Transmission Electron Microscopy (TEM) techniques to understand the sequence of σ phase precipitation at 800°C.

Fingerprints are essential for human identification and are valuable tools in criminal investigations. The pursuit of new materials for digital printing is expanding, with increasing interest in natural compounds such as bixin, sourced from annatto seeds. Despite its traditional use as a natural dye with medicinal properties, the potential of bixin in papilloscopy remains largely untapped. In this study, we meticulously extracted bixin from annatto seeds and meticulously developed composites incorporating zinc carbonate (bixin/ZnCO3) and kaolinite (bixin/kaolinite). UV-visible spectroscopy was used for characterization, and the extracted bixin showed absorption peaks at 429, 453, and 481 nm, which were very similar to standard peaks at 429, 457, and 487 nm. The two samples also had the same retention times (7.07 min) according to further liquid chromatography analysis. Sweat pores were easier to detect thanks to the effectiveness of the bixin/ZnCO3 and bixin/kaolinite composites in creating high contrast sebaceous and natural latent fingerprints. These results highlight the composites’ potential as novel and fascinating instruments for papilloscopy applications, which might also improve forensic investigations.

According to statistics from the Food and Agriculture Organization, the world population will increase to about 91 million (Asia 51 million, Africa 19 million). A rise in the world’s population means an increased need for food. However, climate change has caused desertification and unpredictable weather, creating problems in the supply and demand of food. Sweet potato (Ipomoea batatas) is an alternative to solving the food problem, as it is one of the world’s most important food crops, especially in developing countries. The tuberous roots of sweet potato are usually used as staple food, animal feed, industrial material, or raw material for alcohol production. In the future, more variations of sweet potato will be needed for breeding this crop. Recently, molecular markers developed for sweet potato have demonstrated good potential for use in genetic selection. In this study, a cDNA library was constructed from the total RNA of sweet potato leaves. A total of 789 copies of the cDNA were cloned in Escherichia coli by employing the pGEM-T Easy vector. Sequencing was carried out by Solgent Co. (Korea). As many as 579 expressed sequence tag–simple sequence repeat (EST-SSR) markers were designed (73.38%) from the known cDNA nucleotide base sequences. The lengths of the developed EST-SSR markers ranged from 100 to 499 bp (average length 238 bp). Their motif sequence types were varied, with most being dinucleotides and pentanucleotides, and the most commonly found motifs were CAGAAT (29.0%) and TCT (2.8%). Based on these SSR-containing sequences, 619 pairs of high-quality SSR primers were designed using WebSat and Primer3web. The total number of primers designed was 144. Polymorphism was evident in 82 EST-SSR markers among 20 Korean sweet potato cultivars tested and in 90 EST-SSR markers in the two parents of a mapping population, Yeseumi and Annobeny. In this study, the hexaploid sweet potato (2n = 6x = 90) EST-SSR markers were developed in the absence of full-sequence data. Moreover, by acting as a molecular tag for particular traits, the EST-SSR marker can also simultaneously identify information about the corresponding gene. These EST-SSR markers will allow the molecular analysis of sweet potato to be done more efficiently. Thus, we can develop high-quality sweet potato while overcoming the challenges from climate change and other unfavorable conditions.

Mesenchymal stem cells (MSCs) hold immense therapeutic potential due to their regenerative and immunomodulatory properties. However, to utilize this potential, it is crucial to optimize their in vitro cultivation conditions. Three-dimensional (3D) culture methods using cell-laden hydrogels aim to mimic the physiological microenvironment in vitro, thus preserving MSC biological functionalities. Cellulosic hydrogels are particularly promising due to their biocompatibility, sustainability, and tunability in terms of chemical, morphological, and mechanical properties. This study investigated the impact of (1) two physical crosslinking scenarios for hydrogels derived from anionic cellulose nanofibers (CNF) used to encapsulate adipose-derived MSCs (adMSCs) and (2) physiological culture conditions on the in vitro proliferation, differentiation, and extracellular vesicle (EV) production of these adMSCs. Our results revealed that additional Ca2+-mediated crosslinking, intended to complement self-assembly and gelation of aqueous to-CNF in the adMSC cultivation medium, adversely affected both the mechanical properties of the hydrogel spheres and the growth of the encapsulated cells. However, cultivation under dynamic and hypoxic conditions significantly improved the proliferation and differentiation of the encapsulated adMSCs. Furthermore, we demonstrated that adMSCs in CNF hydrogel spheres exhibited potential for scalable EV production with potent immunosuppressive capacities in a bioreactor system. These findings underscore the importance of physiological culture conditions and the suitability of cellulosic materials for enhancing the therapeutic potential of MSCs. Overall, our study provides valuable insights for optimizing the in vitro cultivation of MSCs for various applications, including tissue engineering, drug testing, and EV-based therapies.

This study introduces a novel and sustainable method of producing graphene from coconut shells and investigates its application in Graphene, Ni/Graphene, and Zn/Graphene electrodes for advanced energy storage devices. The graphene was synthesized scalably using a pyrolysis and impregnation technique, with its successful synthesis verified by X-ray diffraction (XRD), energy-dispersive X-ray spectroscopy (EDX), and electrical conductivity measurements characterizations. The study highlights the enhanced performance of Zn/Graphene electrodes, which outperform both pure graphene and Ni/Graphene variants. This superior performance is attributed to the smaller particle size of Zn (mean = 2.356 µm) compared to Ni (mean = 3.09 µm), and Zn’s more favorable electron configuration for electron transfer. These findings demonstrate the potential of bio-derived graphene composites as efficient, high-performance electrodes, paving the way for more sustainable and cost-effective energy storage solutions.

New dimers of selected dipyridothiazines with an m-xylene linker have been designed, synthesized and characterized. Their structure was identified using 1H and 13C NMR as well as 2D NMR techniques (COSY, ROESY, HSQC and HMBC experiments) and HR MS spectrometry. The compounds were subjected to preliminary in silico biological profile tests using the Way2Drug server and analysis of the probable cytotoxic effect on various cancer cell lines. Preliminary in vitro cytotoxicity tests were performed against normal cell lines (HaCaT) and five cancer cell lines (SW480, SW620, MDA-MB-231, A-549, LN-229) showing moderate activity. An analysis of the structure-activity relationship was performed.

BACKGROUND: Qu-aroma is a critical quality indicator for medium-high temperature Daqu (MT-Daqu), significantly influencing the aroma profile of strong-aroma Baijiu (SAB). SAB is produced across various regions in China, each with unique environmental conditions and production techniques. These regional differences are likely to cause variations in the Qu-aroma of MT-Daqu. Despite this, comprehensive research on the variations in Qu-aroma across different regions has been lacking. This study aims to address this gap by utilizing Gas Chromatography-Olfactometry-Mass Spectrometry (GC-O-MS) and electronic nose (E-nose) technology, combined with sensory evaluation, to analyze the differences in Qu-aroma characteristics and volatile compound profiles of MT-Daqu from seven distinct production areas.RESULTS: Sensory analysis identified seven broad aroma categories and 25 specific aromas characterizing the Qu-aroma of MT-Daqu samples. Chen aroma and roasted aroma were notably more prevalent in MT-Daqu samples from Sichuan compared to those from other regions (P < 0.05), while the fermentation aroma was less prominent in Sichuan samples. In total, 123 volatile compounds were detected in MT-Daqu, with 46 classified as aroma-active compounds. Among these, 21 aroma-active compounds were identified as markers distinguishing Sichuan MT-Daqu from those produced in non-Sichuan regions, showing significant differences in their concentrations (P < 0.05). Additionally, six major aroma-active compounds-ethyl isovalerate, ethyl heptanoate, hexanal, 1-nonanal, (E)-2,4-decadienal, and 2,3-dimethyl-5-ethylpyrazine-were found to significantly contribute to the aroma differences between Sichuan and non-Sichuan MT-Daqu.CONCLUSION: This study delineates the distinct Qu-aroma characteristics of MT-Daqu from various SAB production areas and identifies the aroma-active compounds responsible for these differences. The insights gained from this research offer valuable guidance for optimizing flavor profiles in MT-Daqu production, potentially enhancing the overall quality and regional distinctiveness of the product.

This study investigates the microstructural evolution and mechanical properties of high-nickel shipbuilding steel during thermal processing using High Temperature Confocal Laser Scanning Microscopy (HTCLSM). The in-situ observation of the heating and holding processes reveals critical insights into phase transformations, grain growth behavior, and the formation of precipitates. The experimental results demonstrate that austenitization begins at approximately 700°C, with significant grain boundary nucleation. At 900°C, the formation of black precipitates was observed, and their persistence up to temperatures exceeding 1000°C was confirmed. Scanning Electron Microscopy (SEM) and Energy Dispersive Spectroscopy (EDS) analyses identified these precipitates as chromium carbides (Cr7C3), which significantly contribute to the material's strength. The comprehensive analysis using Transmission Electron Microscopy (TEM) confirmed the presence and distribution of Cr7C3 within the grains and along grain boundaries. These findings provide a deeper understanding of the microstructural dynamics in high-nickel steels, guiding the optimization of heat treatment processes to enhance mechanical properties for maritime applications.

Laser shock peening as an innovative surface treatment technology can effectively improve the fatigue life, sur-face hardness, corrosion resistance, and residual compressive stress. Compared with the laser shock peening, the warm laser shock peening (WLSP) is a new surface treatment technology to improve materials’ surface performances, which takes advantage of thermal mechanical effects on stress strengthening and micro-structure strengthening, results in more stable distribution of the residual compressive stress under heating and cyclic loading process. In this paper, the microstructure of GH4169 nickel super-alloy processed by WLSP technology with differ-ent laser parameters were investigated. The proliferation and tangling of dislocations in GH4169 were observed and the dislocation density increased after WLSP treatment. The influences of different treatment by LSP and WLSP on the microhardness distribution of the surface and along cross-sectional depth were investi-gated. The microstructure evolution of the GH4169 alloy being shocked with WLSP were studied by TEM. The effect of temperature on the stability of high temperature microstructure and properties of GH4169 alloy WLP was investigated.

Honey is a natural product that, thanks to its composition, particularly the high sugar content, is highly appreciated as an energy nourishment. In addition to sugars, it contains many other substances (carbohydrates, free amino acids, enzymatic proteins, organic acids, polyphenols) from which the therapeutic properties of honey arise: hydrating and osmotic activity, antimicrobial action, antioxidant and anti-inflammatory power. The present work aims to deepen the activity of skin protection exerted by honey, as a synergic result of its multiple therapeutic effects.Moreover, the study want to find possible correlations between biological properties and chemical-physical traits of honey. To carry out this research, five varieties of citrus honey, one of acacia honey, one of chestnut honey and, finally, one of multifloral honey were used. The honeys were first characterized by chemical-physical analysis (determination of water content, sugars, amino acids, polyphenols) and then subjected to qualitative melissopalynological analysis. Tests were also carried out to evaluate both their antioxidant power and the effect on collagenase, an enzyme involved in the degradation of collagen present in the extracellular matrix and, therefore, in the processes of skin aging. Finally, they were used in in vitro experiments to assess their action in stimulating cell viability and proliferation on human keratinocytes.

A new class of nano-cube core-shell heterostructures containing Ag coating on the top of WO₃ was fabricated. Physical vapor deposition was used to produce WO₃ based nano-heterostructures. All kind of wet toxic chemical process was avoided to make the process simple and contaminant free. Sputtering of WO₃ and a subsequent thermal annealing process was done to create nano-cubes of WO₃. After that, sputtering of Ag was performed to form the Ag-WO₃ core-shell nano-heterostructures (CSNH). The CSNHs were characterized using field emission scanning electron microscopy (FESEM), energy dispersive spectroscopy (EDS), X-ray diffraction analysis (XRD) and UV-vis spectroscopy. The morphologies, elemental analysis, interfaces, crystallinity, phases, and chemical compositions were analyzed. The bottom-up growth of WO₃ nanocubes was studied using different time periods at 900°C. Ag coating was also studied before and after annealing. Finally, an optical property (band gap) was also analyzed using Tauc plot derive from absorption spectra. The tailoring the band gap of WO₃ from ~2.9eV to ~ 2.45 eV was observed while Ag-WO₃ CSNH formed.

Biochar is a carbonaceous material derived from the thermochemical conversion of biomass under oxygen-lean conditions. Its properties render it many applications in agriculture, environmental remediation, and catalysis. Commonly produced by pyrolysis under a nitrogen atmosphere, the biochar composition is influenced mainly by residence time, heating rate, and process temperature. The existing literature primarily assesses biochar properties, such as ultimate, proximate, calorific, porosity, and combustibility, generated under various thermo-conversion conditions. However, there is a notable lack of sufficient investigation and attention given to the practical application of biochar. This article seeks to bridge that gap by enhancing the comprehension of the necessary experimental assessment for specific biochar applications and proposing process optimization methods using Multi-Criteria Decision Analysis (MCDA). By delving into these aspects, the study offers a concise overview of biochar production and presents a comprehensive panorama based on articles and patents. Additionally, the research explores the physicochemical characterization techniques associated with biochar and its various applications in conjunction with MCDA. This comprehensive approach aims to uncover valuable insights that could further advance the practical and sustainable utilization of biochar in a wide range of fields.

In the context of improving aircraft safety, this study focuses on the development and evaluation of a graphene-based ice detection system using an environmental chamber. The research is driven by the need for more accurate and efficient ice detection methods, crucial in mitigating in-flight icing hazards. The methodology employed involves testing flat graphene-based sensors in a controlled environment, simulating a variety of climatic conditions that could be experienced in an aircraft during its entire flight. The environmental chamber enabled precise manipulation of temperature and humidity levels, thereby providing a realistic and comprehensive test bed for sensor performance evaluation. The results were significant, revealing the graphene sensors’ heightened sensitivity and rapid response to the subtle changes in environmental conditions, especially the critical phase transition from water to ice. This sensitivity is the key to detecting ice formation at its onset, a critical requirement for aviation safety. The study concludes that graphene-based sensors, tested under varied and controlled atmospheric conditions, exhibit a remarkable potential in enhancing ice detection systems for aircraft. Their lightweight, efficient and highly responsive nature makes them a superior alternative to traditional ice detection technologies, paving the way for more advanced and reliable aircraft safety solutions.

This study aimed to characterize the physicochemical properties of broiler poultry litter (BPL) produced from intensively reared commercial broiler farming areas in tropical zone of Tamil Nadu, India. The BPL samples were collected from 110 commercial poultry farms at the end of the production cycle (6th week), further 20 samples were collected from the point of utility. The dry matter (DM), moisture, ash, organic matter (OM), and organic carbon (OC) from the manure samples were 83.04 ± 0.77, 16.96 ± 0.77, 27.08 ± 1.18, 72.92 ± 1.18 and 42.39 ± 0.69 per cent respectively. The pH, Electrical conductivity (EC) (ds m-1), and Kjeldahl Nitrogen (N) were 8.43 ± 0.06, 5.74 ± 0.13, and 24.2 ± 0.84 g kg-1 respectively. The BPL from the cement floor had higher levels of P and K (12.74 and 13.28 ) than the mud floor (10.88 and 10.96). According to the findings of this study, BPL as such at the end of the production cycle is rich in OM, nitrogen, macro and micro minerals at the same time at the point of utility there was a loss of OM, N, and concentration of minerals was noticed, which advocate proper storage and composting process.

Spent coffee grounds (SCG) have great potential as a useful, value-added biological material. In this context, activated carbon (AC) was prepared from SCG by an activation process using H3PO4 at 600°C in air and used as an adsorbent for the azo dye AO7, a model molecule for dye colorants found in textile industry effluents. X-ray diffraction, SEM and BET revealed that the AC was predominantly amorphous, consisting of a powder of 20-100 µm particles with mesopores averaging 5.5 nm in pore size. Adsorption kinetics followed a pseudo-second-order law, while the Langmuir model best fitted experimental isotherm data (maximum capacity of 119.5 mg AO7 per AC g). Thermodynamic parameters revealed that adsorption was endothermic and spontaneous. All the characterizations indicated that adsorption occurred by physisorption via mainly - interactions. The best experimental removal efficiency optimized by means of a Box-Behnken design and response surface methodology was 98% for an initial AO7 concentration of 20 mg.L-1 at pH 7.5 with a dose of 0.285 g.L-1 of AC and a contact time of 40 min. These results clearly show that activated carbon prepared from SCG can be a useful material for efficiently removing organic matter from aqueous solutions.

The surface characterization of indium tin oxide (ITO) films was processed by oxygen (O2) plasma gas using a magnetron sputtering method of varying O2-plasma gas from 20 sccm to 100 sccm for potentially fostering in electronic devices applications on dye-sensitize solar cells (DSSC) in this work. In order to gain an outstanding performance rate with high-quality thin films, the affect of correlation between the electrical, optical, and morphology properties was significantly investigated. Clearly, the content of investigation exhibited that the films properties was changed by variation of the gas composition. These changes have contemporary relevance to the sputtering gas during the deposition process. To conclude, the greatest electrical properties was displayed by O2 -plasma gas flow rate of 20 sccm, which showed the lowest resistivity. In addition to this, the final products were practically fabricated to active layers for dye-sensitize solar cells (DSSC) applications. The highest efficiency of DSSC device was indicated of approximately 0.35% which was located by 40 sccm of the O2-plasma gas. Consequently, the study could be a possibility way of preparing ITO thin films with improved special properties of substantial applications for solar cells devices in the near future.