In this paper, based on our previous expertise on ceramic artifacts, several archaeometric methods applied to some samples collected from the Dudești archaeological site (Oltenia region, Romania) are reported for the first time in the literature. The chemical composition and microstructural and morphological characterization of these samples offer important conclusions about the processing conditions. Some specific techniques such as X-ray diffraction (XRD), wave-length-dispersive X-ray fluorescence (WDXRF), Optical microscopy (OM), stereomicroscopy, scanning electron microscopy (SEM), Fourier transform infrared (FTIR) spectroscopy and Raman spectroscopy, provide composition information about pigments and their decay processes. Additionally, the Brunauer-Emmett-Teller (BET) method helps to estimate pore sizes and specific surface areas. Thermal analysis (TGA) was used to establish details regarding the production technology and the raw materials source used to make the ceramics, too. The obtained results indicated that the ceramics are based on a paste of muscovite, feldspar, with high plasticity, quartz, melanterite, and calcite, the latter in very low concentrations. According to the obtained results, we could assume that non-calcareous clays are present in the investigated samples because calcium exists in low concentrations. Gypsum is present, too, in very low concentration, identified by the presence of sulfate group in WDXRF. In the same context, iron oxides significantly impact the firing atmosphere of iron-rich clay, resulting in blackening under reducing conditions and reddish coloration under oxidative conditions. Using hematite and gypsum as pigments further contributes to the color variations in the pottery. The consistent firing temperature range of 200-600 °C in Dudești pottery implies a standardized production process, the variation in color being dependent on the specific reducing/oxidative regime conditions. This relationship between clay composition and local sources suggests a connection to Neolithic pottery production in the region and their color depending on the reducing/oxidative regime conditions.

Composite fiber materials are superior materials due to their high strength and light weight. Composites reflect the properties of their constituents, which is proportional to the volume fraction of each phase. There are different fiber reinforcement types and each affects it’s flexural, tensile and compression strength. When selecting a composite for a specific application, the forces excreted on the composite must be known in order to determine the reinforcement type. Unidirectional fiber reinforcement will allow very strong load resistance but only in one direction where as a random orientated fiber reinforcement can resist less load but can maintain this quota in all directions. These materials are said to be anisotropic. Certain composite fibers, taking into consideration there weights, are physically stronger than conventional metals. This research deals with the analysis of three composite materials with different reinforcement types, volume fraction and phase content. It was found that material A (glass epoxy) was the strongest in the longitudinal direction with a flexural strength of 534 MPa in the longitudinal and 420 MPa in the transverse direction. The flexural stresses of material B (glass silicone) and material C (glass polyester) where both found in the 120 to 135 MPa range. Differences were due to their differences in matrix composition and reinforcement type.

The rational design of magnetic carbon composites, encompassing both composition and microstructure, holds significant potential for achieving exceptional electromagnetic wave absorbing materials (EAMs). In this study, FeCo@CM composites was efficiently fabricated through an advanced microwave plasma assisted reduction chemical vapor deposition (MPARCVD) technique, offering high efficiency, low cost, and energy-saving benefits. By depositing graphitized carbon microspheres, the dielectric properties were significantly enhanced, resulting in improved electromagnetic wave absorption performances through optimized impedance matching and a synergistic effect with magnetic loss. A systematic investigation revealed that the laminar-stacked structure of FeCo exhibited superior properties compared to its spherical counterpart, supplying a higher number of exposed edges and enhanced catalytic activity, which facilitated the deposition of uniform and low-defect graphitized carbon microspheres. Consequently, the dielectric loss performance of the FeCo@CM composites was dramatically improved due to increased electrical conductivity and the formation of abundant heterogeneous interfaces. At a 40 wt% filling amount and a frequency of 7.84 GHz, the FeCo@CM composites achieved a minimum reflection loss value of -58.2 dB with an effective absorption bandwidth (fE) of 5.13 GHz. This study presents an effective strategy for developing high-performance EAMs.

This article discusses the application of thermal quality control methods for plant tissues. The purpose of the work is to determine the optimal parameters of thermal impact on a spherical-shaped plant control object, ensuring the detection of surface and subsurface defects. The authors of the work proposed mathematical models of the temperature field for a spherical body with defects and a flat sample when exposed to the thermal influence of a pulsed source. As a result of the use of mathematical models, the thermophysical characteristics of plant tissues of varying degrees of disease damage were obtained, which made it possible to simulate the temperature field of the control object and obtain an image of classified tissues. The developed recommendations made it possible to select the optimal parameters of the thermal effect on the test object.

Coal currently accounts for over 38% of electric power generation around the globe. Hence, it is a significant critical contributor to socio-economic growth and development, particularly in the BRIC economies. The success of the coal energy in these nations in addition to the discovery of vast new coal deposits have revived Nigeria’s interest in coal power. However, there is lack of comprehensive data on the pollution emission profiles, along with the physicochemical, thermal, and kinetic properties of Nigerian coals as required for power plant operations. Therefore, this paper presents preliminary findings on the physicochemical, microstructural, mineralogical and thermal properties of Owukpa (WKP) coal from Benue State in Nigeria. The results showed that WKP contains high compositions of combustible elements and heating value but low pollutant elements. Furthermore, thermal degradation revealed high conversion efficiencies particularly under oxidative conditions as required for electric power generation through combustion.

The results of a study of the processes of formation of macro- and micro-inhomogeneity of ingots and rolled sheets are presented. To study the nature and sources of surface defects in rolled sheets, a comparative method of structural-concentration analysis of metal at the end-to-end metallurgical process of ingot - slab - sheet metal has been developed, based on the metallographic method of studying the structure and qualitative analysis of non-metallic inclusions. The research results showed that the quality of the surface of rolled sheets is determined mainly by the physical heterogeneity of the crust zone of the ingots, and the internal defects of thin rolled sheets largely depend on the contamination of the metal with non-metallic inclusions and off-axis segregation. A mechanism for transforming defects in the casting cortical zone into surface and internal defects in rolled sheets is proposed.

Superconducting YBa2Cu3Oy (YBCO) foams were prepared using commercial open-cell, polyurethane foams as starting material to form ceramic Y2BaCuO5 (Y-211) foams which are then converted into superconducting YBCO by using the infiltration growth process. For modelling the superconducting and mechanical properties of the foam samples, a Kelvin-type cell may be employed as a first approach like done in the literature for pure polyurethane foams. However, for a refined model of a superconducting foam sample, the real sample structure must be considered. Thus, a proper description of the specific microstructure of the superconducting YBCO foams is required. A variety of parameters including the cell size and shape, the window size and shape, the length and shape of the foam struts or ligaments and the respective angles of intersection are used to describe the real foam structure. To obtain a set of reliable data, YBCO foam samples were investigated using optical microscopy, SEM and electron backscatter diffraction (EBSD). The detailed investigation of the foam microstructure reveals not only the differences to the polymeric foams used as base material, but also gives insight to details of the infiltration growth process via the increased surface amount in a foam sample.

Patients with predominantly antibody deficiencies (PAD) display hypogammaglobulinemia with a high prevalence of infections, along with autoimmune manifestations, benign and malignant lymphoproliferation and granulomatous disease. It is noteworthy that PAD patients, even those with defects in the same causative genes display a variable clinical phenotype, suggesting that additional genetic polymorphisms, located in either immune-related or non-immune-related genes, may affect their clinical and laboratory phenotype. In this context, we analyzed 80 PAD patients, including 70 with common variable immunodeficiency (CVID) for SERPINA1 defects, in order to investigate their possible contribution to PAD clinical phenotype. Eight CVID patients carried heterozygous pathogenic SERPINA1 defects with normal alpha-1 antitrypsin levels. Interestingly, the presence of the Z allele (rs28929474) which was found in three patients, was significantly associated with liver disease; hepatic complications were also observed in patients carrying the p.Leu23Gln (rs1379209512) and the p.Phe76del (rs775982338) alleles. Conversely, no correlation of SERPINA1 defective variants with respiratory complications was observed, although patients with pathogenic variants exhibit a reduced probability of developing autoimmune diseases. Therefore, we recommend SERPINA1 genetic analysis in PAD, in order to identify patients with a higher risk for liver disease.

.With the increasing use of carbon fiber reinforced plastics in various area, carbon fiber composites based on prepregs have attracted attention in industries and academia research. However, prepreg manufacturing processes are costly, and the strength of structures varies depending on the orientation and defects (pores and delamination). For non-contact evaluation of internal defects, we proposed lock-in infrared thermography to investigate orientation angles after a compression test. We also conducted a drop-weight impact test to study the behaviour of the composites after impact according the fibers orientation for composite fabricated using unidirectional carbon fiber prepregs. Using CAI tests, we determined the residual compressive strength and confirmed the damage modes using a thermal camera. The results of the drop weight impact tests show that the specimen laminated at 0° suffered the largest damage because of susceptibility of the resin to impact. In contrast, the specimens oriented in of 0°/90° and +45°/–45° directions transferred more than 90% of the impact energy back to the impactor because of the lamination of fibers in the orthogonal directions. Furthermore, the specimens that underwent complete damage in the impact tests were subjected to the lock-in method and showed internal delamination and cut fibers. With the finite elements analysis, the damage of each ply could be observed. Moreover, the temperature differences in the residual compression tests were not significant.

Plasma Electrolytic Oxidation (PEO) is a surface treatment, similar to anodizing, that produces thick oxide films on the surface of metals. In the present work, PEO coatings were obtained on zinc-aluminized (ZA) carbon steel using as electrolyte a solution containing sodium silicate and potassium hydroxide, and working with high current densities and short treatment times in DC mode. The surface morphology resulted the typical one of PEO layers, with the presence of a lot of pores and micro-cracks. Considering the cross section, the thickness of the coating was strongly influenced by the process parameters, with different dissolution grades of the ZA layer depending on the current density and treatment time. The PEO layer resulted mainly composed by aluminum and zinc oxides and silicates. The corrosion resistance was remarkable increased in the samples with the PEO coating.

Marine clay deposits are commonly found worldwide. Considering the cost of dumping and the related environmental concerns, an alternative solution involving the reuse of soils that have poor conditions is crucial. In this research, the authors examined the durability of marine deposited clays and compiled a corresponding database. The use of slag alone as a binder, at any percentage, increased the accumulated mass loss (ALM) up to 2%. However, the use of lime as the third binder seemed to accelerate the chemical reactions associated with the hydration of clay and cementitious material and to enhance the chemical stability, i.e., samples that included both lime and slag experienced the same ALM as samples treated with cement only. Scanning electron microscopy analysis confirmed the durability improvements of these clays. The proposed unconfined compressive strength and accumulated mass loss relationship yielded practical approximation for the fine- and coarse-grained soils blended with up to three binders until 60 days of curing.

Alzheimer’s disease (AD) and the therapies of AD with anti-amyloid1-42 (Aβ) monoclonal antibodies are associated with the vascular complications of brain edema, hemorrhage, and cerebral amyloid angiopathy (CAA) termed amyloid-related imaging abnormalities (ARIAs). The neuropathology of normal and AD brains demonstrates that monocyte/macrophages (MMs) are critical in successful brain clearance in healthy brain by up-loading, transporting, and degrading Aβ but fail degradation and clearance in AD patients by releasing Aβ into vessels at the blood-brain barrier, causing vasculitis and ARIAs. The naturally-formed epoxides (EpFAs) of polyunsaturated fatty acids (PUFA’s), including arachidonic, docosahexaenoic, and eicosapentaenoic fatty acids, may repair degradation of Aβ by regulating Aβ-degrading enzymes, inflammatory cytokines, and unfolded protein response (UPR) to endoplasmic reticulum stress in a homeostatic fashion. EpFAs are, however, degraded by the soluble epoxide hydrolase enzyme (sEH) but are protected by the sEH inhibitor (sEHI) TPPU. In the cultures of AD patients’ macrophages, TPPU with the epoxide EEQ, and the cGAS/STING inhibitor H-151 increased uptake of Aβ at 2 hours and degradation of Aβ at 24 hours. In conclusion, the soluble epoxide hydrolase inhibitor TPPU with omega-3 fatty acids and the cGAS/STING inhibitor H-151 increase Aβ uptake and degradation in macrophages of AD patients, and potentially enhancing Aβ clearance in the AD brain.

Damaged connective tissues between the bone and tendons or ligaments are common among adults regardless of activity level. Achilles tendinosis is one of the most common tissue defects and enthesopathies. The patient in this study is a 54-year-old female with chronic Achilles tendinosis from chronic enthesopathy at the Achilles tendon insertion with a retrocalcaneal exostosis for three years who has failed standard-of-care practices for over two years. The patient received extracorporeal pulsed-activated therapy (EPAT) before applying 2ml of CryoText, a Wharton’s jelly tissue allograft. The patient then received class IV laser therapy treatments twice weekly for three weeks. The patient started with a 10/10 VAS at the initial visit. At five weeks post-application, the patient’s score had improved by 80% at 2/10 VAS. By week 13, the patient rated her pain as 0/10 VAS. The improvement in patient-reported pain and functionality reported in this study after the application of Wharton’s Jelly, EPAT, and class IV laser therapy warrants future research studying the safety and efficacy of these patient care modalities together.

Chromium (Cr) metal has garnered significant attention in alloy systems owing to its exceptional properties, such as high melting point, low density, and superior oxidation and corrosion resistance. However, its processing capabilities are hindered by the high Ductile-Brittle Transition Temperature (DBTT). Recently, powder bed fusion-laser beam for metals (PBF-LB/M) has emerged as a promising technique, offering the fabrication of net shapes and precise control over crystallographic texture. Nevertheless, research investigating the mechanism underlying crystallographic texture development in pure Cr via PBF-LB/M still needs to be conducted. This study explores the impact of scan speed on relative density and crystallographic texture. At the optimal scan speed, an increase in grain size attributed to epitaxial growth was observed, resulting in the formation of cubic texture. Consequently, a reduction in High Angle Grain Boundaries (HAGB) was achieved, suppressing defects such as cracks and enhancing relative density up to 98.1%. Furthermore, with increasing densification, Vickers hardness also exhibited a corresponding increase. These findings underscore the efficacy of PBF-LB/M for processing metals with high DBTT properties.

Finely ground glass has the potential for pozzolanic reactivity and can serve as a supplementary cementitious material (SCM). Glass reaction kinetics depends on both temperature and glass composition. Microstructural modeling is a helpful approach to get better understanding of cement hydration and microstructure development. Mechanical and performance properties of concrete are directly related to the development of concrete microstructure, which is the consequence of progress in cement hydration. This study initially provides a comprehensive background about cement hydration process and microstructural modeling of the hydration. It then utilizes results of experimental studies, i.e. isothermal calorimetry and thermogravimetric analysis, to find kinetics equation parameters called “Avrami Constants”. For the first time, these constants were found for three main components of cement, i.e. C₃S, C₂S, and C₃A, and also for glass particles smaller than 25 µm. Although modeling of cement hydration and cementitious systems containing single glass particles showed promising results, simulations of combined glass types and sizes showed that more work on microstructural models is needed to properly model the reactivity of mixed glass particle systems.

Epoxy matrix composites reinforced with high-performance fibers such as carbon, Kevlar, and glass, exhibit excellent specific stiffness and strength in many mechanical applications. However, these composites are disappointingly non-recyclable and are usually disposed of in landfill sites, with no realistic prospect for biodegradation in reasonable time. In contrast, moldable composites with carbonized elastomeric matrices developed in the last decades possess attractive mechanical properties in final net-shape products and can also be incinerated or recycled. Many carbon and inorganic fillers have recently been evaluated to adjust the properties of carbonized elastomeric composites. Renewable organic fillers such as human or animal hair offer an attractive fibrous material with substantial potential for reinforcing composites with elastomeric matrices. Samples of unidirectional fiber composites (with hair volume fraction up to 7 %) and quasi-isotropic short fiber composites (with hair volume fraction up to 20 %) of human hair-reinforced nitrile butadiene rubbers (HH-NBR) were produced in the peroxide-cured and carbonized states. The samples were characterized using SEM, Raman spectroscopy and photoacoustic microscopy. Mechanical tests were performed in tension using a miniature universal testing machine. The expected effect of fiber reinforcement on the overall mechanical performance has been demonstrated for both cured and carbonized composites. Considerable enhancement of the elastic modulus (up to 10 times), ultimate tensile strength (up to 3 times) and damage tolerance was achieved. The evidence of satisfactory interfacial bonding between hair and rubber was confirmed by SEM imaging of fracture surfaces. The suitability of photoacoustic microscopy was assessed for 3D reconstruction of the fiber sub-system spatial distribution and non-destructive testing.

Defect detection and identification from fruits and vegetables are particularly challenging for Indian agriculture. Defect Detection is a process to identify the defects or damages in vegetables and fruits, based on the shapes, colors and textures. The local market finds it difficult to cope with the defects and other infections in fruits and vegetables as quality evaluations and classification of vegetables and fruits have become tedious process. Recently, several approaches based on Image processing, Machine Learning and Artificial Intelligence methods have been proposed for the purpose of defect detection. On the basis of classifying the types of defects, related pathogens, and physical and morphological characteristics descriptors, we review the different approaches based on a corpus of 57 articles between 2016 and 2021. In the process of describing the defect analysis, steps from the target articles, algorithms, and methods including qualitative and quantitative evaluation are mainly summarized. The aim of this current review work is to present-day novel images and collects recent defective area calculation methods to detect surface defects of fruits and vegetables using RGB images and to classify whether the fruit is defected or fresh. A rigorous evaluation of many new algorithms provided for quality assurance by researcher’s probes of vegetables and fruits have been conducted in this work. This review work conveys that using the recent identification features will help to decrease the disadvantages in fruit storeroom owing to storage of the affected vegetables and fruits, ie. Preventing the spread of defects and other infections from the infected fruits and vegetables to the fresh ones.

Density functional theory (DFT) calculations of hydrogen adsorption on titanium nitride had previously shown that hydrogen may adsorb on both titanium and nitrogen sites with a moderate adsorption energy. Further, the diffusion barrier was also found to be low. These findings may qualify TiN, a versatile multifunctional material with electronic conductivity, as electrode material for the hydrogen evolution reaction (HER). This was the main impetus of this work which aims to experimentally and theoretically investigate the electrocatalytic properties of TiN-layers that were processed on Ti substrate using reactive ion sputtering. The properties are discussed focusing on the role of oxygen defects introduced during the sputtering process on the HER. Based on DFT calculations, it is shown that these oxygen defects alter the electronic environment of the Ti atoms which entails a low hydrogen adsorption energy in the range of -0.1 eV; this leads to HER performances that match those of Pt-NPs in acidic media. When a few nanometr thick layer of Pd-NPs is sputtered on-top of the TiN-layer, the performance is drastically reduced. This is interpreted in terms of oxygen defects being scavenged by the Pd-NPs near the surface which is thought to reduce the hydrogen adsorption sites.

The aim of the work is to study the effect of the 3D printing process on the microstructural and hydrophilic properties of polylactic acid (PLA) samples with various model printing patterns obtained from the black Filament PLA by sequentially applying polymer layers using the FDM (Fused Deposition Modeling) method. X-ray phase analysis revealed partial crystallization of PLA polymer chains in printed samples, which occurs under thermal and mechanical action on the original amorphous PLA filament during 3D printing to varying degrees, depending on the geometry of the pattern and the morphology of its surface. At the same time, IR spectroscopy data indicate the preservation of all intrastructural chemical bonds of polylactide. Measured at the original installation, the values of the wetting edge angles on the surface of the printed samples are in the range φ = 50-60°, which is significantly less than the right angle. This indicates the hydrophilic properties of all samples’ surface. At the same time, the influence of different geometries of model drawings in printed samples was found not only on the morphology of the samples’ surface according to SEM data, but also on its wettability.

This research presents a comprehensive bibliometric and sentiment analysis of nanocomposite literature from 1990 to 2024. Employing cutting-edge computational methods, the study delves deep into the progression of microstructural characterization, electrical properties, and mechanical behaviors of nanocomposites. The analysis utilizes advanced Boolean search strategies from the Scopus database, ensuring a thorough extraction of thematic content. The results explore various themes and insights, shedding light on trends evident in the Scopus database, particularly the prominence of research on nanocomposite microstructure, electrical attributes, and mechanical performance. The paper also offers textual analytics and bibliometric data, showcasing critical collaborative efforts and influential studies. Significant discoveries encompass the evolution of research language, shifts in thematic focus, and global contributions, providing a comprehensive perspective on the current landscape of nanocomposite research and its dynamic evolution. Moving forward, the "State-of-the-Art and Gaps Extracted from Results and Discussions" section of the paper delves into the most recent advancements in nanocomposite research. It delves into various types of nanocomposites, with a particular emphasis on their microstructural characteristics, electrical properties, mechanical dynamics, and the application of nanocomposite films. This section identifies key research themes, traces historical progress, and highlights emerging trends while underscoring the significance of collaboration and the influence of pivotal studies that have shaped the field. Lastly, in the "Literature Review Guided by Artificial Intelligence" section, the paper introduces a revised approach for researching nanocomposites through AI-guided techniques. This approach prioritizes articles published in 2023 based on citation frequency. Here, the focus is on exploring the relationship between nanocomposites and their electrical properties, emphasizing their fundamental interactions and impact on electrical characteristics. Various nanocomposite systems are covered, highlighting their composition, structure, and functionality. Findings from recent studies are integrated to provide a comprehensive overview of the current state of knowledge in this area. Notably, the sentiment analysis, anchored by an average sentiment score of 0.638771, underscores a positive trajectory in academic discourse, emphasizing the growing recognition of the potential of nanocomposites. The bibliometric exploration maps the intellectual domain, emphasizing pivotal research themes and the influence of crosslinking time on nanocomposite attributes. While this study is thorough, it acknowledges its limitations and advocates for broader database inclusion in future research endeavors. This work elucidates the prevailing trends in nanocomposite research, emphasizing the indispensable role of computational tools in comprehending this vast wealth of information.

The microstructure of the coating during hot-dip galvanizing under industrial conditions of two structural steels, a low-silicon ASTM A36 steel and a high-silicon Q345B steel, both of commercial quality, have been characterized for industrial-relevant times. For both cases it is noted that the formation of the Fe-Zn phases begins in early stages during the heating of the steel, a situation in which all the phases are in the solid state. The characterization was carried out through traditional metallographic techniques including SEM-EDS and DRX equipment. The evolution in time of the microstructure of both steels is examined, being able to observe that the mechanism by which silicon accelerates the formation of Fe-Zn phases in galvanizing is related to the change in the energy of the interfaces caused by a silicon accumulation in the liquid phase in contact with the ζ layer. These results provided us with a deeper understanding of the phase evolution in the hot-dip galvanizing of high silicon steels.

The microstructural evolution, thermodynamics and kinetics of Mo-21%Tm₂O₃ (mass fraction, %) powder mixtures during ball milling were investigated using X-ray diffraction and transmission electron microscopy. Ball milling induced Tm₂O₃ to be decomposed and then dissolved into Mo crystal. The supersaturated nanocrystalline solid solution of Mo (Tm, O) was obtained after 96 h of ball milling. The elements of Mo, Tm and O were distributed uniformly in the ball-milled particles. Based on the semi-experimental theory of Miedema, a thermodynamic model was developed to calculate the driving force of phase evolution. There was no chemical driving force to form a crystal solid solution of Tm atoms in Mo crystal or an amorphous phase because the Gibbs free energy for both processes was higher than zero. For Mo-21%Tm₂O₃, it was mechanical work, not negative heat of mixing, that provided the driving force to form supersaturated nanocrystalline Mo (Tm, O) solid solution.

This work deals with the analysis of phase composition of sintered Ti-Al-C composite materials under high voltage electrical discharge. The samples of Ti-Al-C powder composites were tested by SEM, Raman spectroscopy and XRD. It was determined that the treatment of the powder by high voltage electrical discharge (HVED) and further sintering at high temperatures using the method of spark plasma sintering (SPS) encourages the formation of the intermetallic reinforcing phases, carbides and different nanocarbon structures like graphene and fullerenes, as well as pure graphite. Intermetallic phases and nanocarbon structures improve mechanical and physical properties of the composites. By using experimental methods mentioned above, the phase composition of Ti-Al-C powder composites obtained at different sintering temperatures was determined.

Conventional heat treatment is not capable of converting a sufficient amount of retained austenite into martensite in high-carbon or high-carbon and high-alloyed iron alloys. Cryogenic treatment induces the following alterations in the microstructures: (i) a considerable reduction in the retained austenite amount, (ii) formation of refined martensite coupled with an increased number of lattice defects, such as dislocations and twins, (iii) changes in the precipitation kinetics of nano-sized transient carbides during tempering, and (iv) an increase in the number of small globular carbides. These microstructural alterations are reflected in mechanical property improvements and better dimensional stability. A common consequence of cryogenic treatment is a significant increase in the wear resistance of steels. The current review deals with all the mentioned microstructural changes as well as the variations in strength, toughness, wear performance, and corrosion resistance for a variety of iron alloys, such as carburising steels, hot work tool steels, bearing and eutectoid steels, and high-carbon and high alloyed ledeburitic cold work tool steels.

It is very difficult to repair large bone defects, especially when they have a complex shape. We have developed a new technique to make a desired copy of rabbit bones. A rabbit distal femur was scanned by computed tomography (CT), and a rectangular-shaped beta-tricalcium phosphate (β-TCP) block with 75% porosity was automatically machined using milling tools into a half-scale copy of the distal femur based on the CT data. The β-TCP block was seeded with bone morphogenetic protein-2 and bone marrow cells obtained from the femur and implanted on the periosteum of the femur. At 10 weeks after implantation, most of the β-TCP block had been replaced by bone and a complete copy of the distal femur was reconstructed. Our findings indicate that this technique will be useful in the clinical setting. We also report the representative clinical results of treatment with β-TCP graft in patients with bone defects since 1989.

Grape dehydration is practiced widely in the food industry with large yields of sultanas produced globally. This paper proposes an investigation into grape microstructure changes as it is dried by imaging specimens at intervals during dehydration at two temperatures using scanning electron microscopy. Detailed images of the microstructure were obtained, and a unique image processing algorithm was developed to quantitatively analyse the properties of this microstructure. Two main methods were developed to obtain the complex boundaries of cells present in the grape tissue in over 36 SEM images. Segmentation of the binary image using an adapted watershed function obtained the most consistent and accurate morphological shape. This was compared to a secondary method which used Canny’s edge detection function, morphological closing and skeletonizing to outlines the cellular microstructure. MATLAB was utilised to convert these boundaries into measurable areas so that quantitative data on average cell area, perimeter and cell axis lengths was acquired. It was found that over drying time cell area and perimeter reduced as expected. Some variability in the data was clear due to only single samples being analysed for each temperature and time combination. The development of automatic image processing techniques will enable quantitative data to be extracted from these images. Trends in cell perimeter, diameter and shape will be used to demonstrate relationships between morphological structure, drying temperature, and duration.

This study aims at relating the microstructural arrangement, in particular the symmetry materialised by filament sequencing in fused filament fabrication process on mechanical behaviour of printed polyamide. Dogbone structures are printed using various printing temperatures, which are combined with part orientation and raster angle that represent the in-plane and out-of-plane symmetrical arrangement of filament. Mechanical testing is conducted on both as-received filaments and printed structures to derive the effect of filament arrangement symmetry and process-generated defects on mechanical loss. In addition, microstructural analysis using scanning electron microscopy is used to share more light on the filament arrangement and their consequence on deformation mechanisms with respect to the printing conditions. The results show that 3D printed polyamide-based material exhibit remarkable tensile performance with strain stiffening behaviour and large elongation at break thanks to particular filament layout. Among the considered printing conditions, the part orientation is found to have the largest influence on tensile behaviour, which modulates the behaviour from complete restoration of the filament performance to mechanical loss.

Fabry-Perot air chamber was constructed at the melting point (splicing location) of two single-mode fibers by glycerin assisted self-expansion method. The morphology of the Fabry-Perot air chamber was fabricated and optimized by modulating the splicing parameters (drawing process, discharging location, time and intensity) and the fibers’ end-face (plane or arc). The in-line or reflected Fabry-Perot cavities have been applied to determine the tensile strain in the range of 0-1.2 N. The train sensing performance of the spherical shaped FP cavity has been experimentally demonstrated with the best sensitivity of 3.628 nm/N, corresponding to the resolution of ~0.005 N. The proposed FP fiber sensor has the advantages of low cost, fast fabrication and easy-integration with the common fiber system.

In this study, the efficiency of coating (alginate and carrageenan) and osmotic dehydration pre-treatment (NaCl and sucrose) on decreasing oil uptake of potato strips was assessed. It was examined how various pre-treatments affected the sample’s texture, morphology, color and density properties as well as their moisture content and effective moisture diffusion coefficient (Deff). Results showed that NaCl osmotic dehydration pre-treatment and sucrose solution decreased oil uptake by 30.76% and 41.75%. This is attributed to moisture removal increasing caused by improving dielectric properties. Osmotic dehydration and coating pre-treatment frequently enhanced product shrinkage, browning index, a* and ∆E. Conversely, density, lightness, breaking force, Deff and b* decreased. In control samples, SEM revealed a severely damaged internal structure in comparison to a tissue homogenous layer produced by coating. For moisture loss and oil uptake, the coefficient of determination (R2) and root mean square error (RMSE) of eight empirical models were compared. Finally, the Dehghannya and Krokida model (moisture loss) and the Movahhed and Naghavi model (oil uptake) were found the best fit to the experimental data. Although coating pre-treatment and osmotic dehydration can be used as an alternate de-oiling approach for potato chips, the mechanism of oil uptake reduction differ.

The effects of 0.4wt.% Sc addition on a typical Al-Si10-Mg alloy were systematically investigated in the present research. Samples with and without Sc produced refined dendritic arranged microstructures with sensitivity to the aging treatment after solidification, particularly in the case of the alloy without Sc. After being exposed to 300°C for 90 minutes, the dendritic spacing nearly doubled in the Al-10wt.%Si-0.45wt.%Mg samples. The rapidly solidified microstructures were constituted by the -Al dendritic phase surrounded by eutectic phases/intermetallics such as Si, Mg2Si and Al3Sc (in the case of the alloy containing Sc). 255°C and 300°C were deemed most appropriate temperatures for aging treatments, with four exposure times of up to 120 minutes tested for each alloy. The heat treatments allowed the Vickers hardness profiles to be plotted and compared. Moreover, in order to detect both Sc- and Mg- precipitates after aging, specific samples have been prepared for either SEM or TEM analyses. At first, the results pointed to a strong precipitate-related hardening effect formed as a result of the Sc addition to the alloy. All samples containing Sc showed a higher hardness value when compared to their respective treated samples without Sc. Secondly, when comparing the Al-10Si-Mg-Sc alloy samples among themselves after being treated at different conditions, high temperatures and excessive treatment times can become detrimental to the hardness. This was due to the growth of larger Sc-bearing precipitates of approximately 1 µm in size under such conditions, having less pronounced hardening effect. The best condition (255°C for 60 min) for as centrifuged samples in Cu-mold produced very fine dispersion of Mg- and Sc- intermetallics (~200 nm in size) with a peak hardness of 110 HV.

Foot pain related to the plantar fascia is common in adults regardless of athletic background. Many pathologies can lead to the diagnosis of plantar enthesopathy, but the most relevant to this case study is related to structural defects within the plantar fascia. Due to the variety and sometimes unclear etiology of plantar fasciosis, no single standard of care treatment protocol is recognized. Often, patients receive NSAIDs, night splints, taping, physical therapy, foot orthosis, and extracorporeal shock wave therapies. This study presents Wharton Jelly (WJ) tissue allografts as an additional intervention for patients who fail standard-care treatments. WJ allografts are applied to supplement connective tissue defects directly, unlike other therapies, which aim to reduce swelling and symptomatic pain. This retrospective study includes seven patients who have previously failed standard-of-care treatment. Each received extracorporeal pulse-activated therapy (EPAT), WJ, laser therapy, and an orthotic. Patient progress was tracked using a visual analog scale, 0-10 scoring, reported by the patient at the initial visit and approximately thirteen weeks following, reporting an average improvement of 50%. The study's limitations include a small cohort size and a non-blinded retrospective design. These promising results provide evidence for a more extensive, randomized study to define dosage protocols further and confirm safety and efficacy.

In this study, a 5vol. % (TiBw+TiCp)/Ti composite pancake with a diameter of 260mm was prepared by casting followed by open die forging in (α+β) phase region. The microstructures of the composite pancake are inhomogeneous, in terms of both matrix microstructure and distribution of reinforcements. The matrix microstructures were gradually refined from the periphery to centre of the pancake. The TiBw and TiCp reinforcements tend to be uniformly distributed in the centre region and. It is suggested that the microstructure difference can be mainly ascribed to the temperature variation from the periphery to the centre. Additionally, tensile testing results showed that the centre region of the composite pancake exhibits higher strength than the peripheral region. The strengthening mechanism and the softening behavior of the composite pancake with temperature is discussed.

Assuming the Multiple Point Principle (MPP) as a new law of Nature, we considered the existence of the two degenerate vacua of the Universe: a) the first Electroweak (EW) vacuum at $v_1\approx 246$ GeV—“true vacuum”, and b) the second Planck scale “false vacuum” at $v_2 \sim 10^{18}$ GeV. In these vacua, we investigated different topological defects. The main aim of the paper is an investigation of the black-hole-hedgehogs configurations as defects of the false vacuum. In the framework of the $f(R)$ gravity, described by the Gravi-Weak unification model, we considered a black-hole solution, which corresponds to a “hedgehog”—global monopole, that has been “swallowed” by the black-hole with mass core $M_{BH}\sim 10^{18}$ GeV and radius $\delta\sim 10^{-21}$ GeV$^{-1}$. Considering the results of the hedgehog lattice theory in the framework of the $SU(2)$ Yang-Mills gauge-invariant theory with hedgehogs in the Wilson loops, we have used the critical value of temperature for the hedgehogs’ confinement phase ($T_c\sim 10^{18}$ GeV). This result gave us the possibility to conclude that the SM shows a new physics (with contributions of the $SU(2)$-triplet Higgs bosons) at the scale $\sim 10$ TeV. This theory predicts the stability of the EW-vacuum and the accuracy of the MPP.

In this study, Ni50Ti50 powder was coated on the surface of graphite substrate (C) by plasma spraying process using a radio frequency inductively coupled plasma reactor. The coating was carried out by using 12- and 9-kW power under Ar atmosphere. The cross-section of coating layers and the surface were examined with SEM, EDX, XRD analysis and microhardness test. The thickness and quality of the coating increased with input power. Many pores were detected in the cross-sectional surface areas. Higher input power caused a better coating layer in NiTi alloy. The hardness of the coating layer decreases with higher input power.

The high entropy alloy (HEA) of equiatomic composition CrNiFeCoMn and with FCC crystal structure was additively manufactured with a selective laser melting (SLM) process starting from mechanically alloyed powders. The as produced alloy shows finenitride and  phase pre-cipitates, which are Cr-rich and stable up to about 900 K. The precipitates increase in number and dimensions after long-period annealing at 900-1300 K, with a change in the HEA mechanical properties. Higher aging temperatures in furnace, above 1300 K, turn the alloy in a single FCC structure, with disappearance of the nitrate and  phase precipitates inside the grains and at the grain boundaries, but with still a presence of a finer Cr-rich nitride precipitation phase. These re-sults suggest that the as-produced HEA is a supersatured solid solution at low and intermediate temperature with nitrides and  nanostructures.

Background: Kidney damage is considered to be one of the risk factors for severity and mortality among COVID-19 patients. However, molecular nature of such observations remains unknown. Hypothesis: Altered gene expressions due to infection and in chronic kidney disease could explain severity in COVID-19 with kidney defects. Methods: We collected gene expression data from publicly available resources Gene Expression Omnibus CKD, Enrichr for deregulated genes in SARS-CoV infected cells in vitro, DisGeNET and others and carried out enrichment analysis using Enrichr. Result: Number of common genes altered in chronic kidney disease (CKD) and SARS-CoV infected cells was 2834. Enrichment analysis revealed that biological processes related viral life cycle and growth, cytokines, immunity, interferon, inflammation, apoptosis, autophagy, oxidative stress and others were significantly enriched with common deregulated genes. Similarly, significantly enriched pathways related to viral and bacterial infections, immunity and inflammation, cell cycle, ubiquitin mediated proteolysis, signaling pathways like Relaxin signaling pathway, mTOR signaling pathway, IL-17 signaling pathway, NF-kappa B signaling pathway were enriched with the common deregulated genes. These processes and pathways are known to be related to kidney damage. DisGeNET terms enriched include and related to Dengue fever, chronic Hepatitis, measles, retroviridae infections, respiratory syncytial virus Infections and many others. Kidney dysfunction related terms ischemia of kidney, renal fibrosis and diabetic nephropathy. Conclusion: Common deregulated genes in SARS-CoV infected cells and chronic kidney disease, as well as their enrichment with molecular processes and pathways relevant for viral pathogenesis and renal dysfunctions, could explain the severity of COVID-19 with kidney disease. This observation not only provides molecular relation of severity in COVID-19 with renal dysfunctions but might also help in the management and treatment targets for these cases.

Protrusive defects on the color filter of thin-film transistor (TFT) liquid crystal displays (LCDs) frequently damage the valuable photomask. An fast method using side-view illuminations associated with digital charge-couple devices (CCDs) to detect the protrusive defect in the four substrates, which are the black matrix (BM), red, green, and blue. Between the photomask and substrate, the depth of field (DOF) is normally 300 μm for the proximity-type aligner; we select the four substrates to evaluate the detectability in the task. The experiment is capable of detecting measurements of 300 μm and even lower than 100 μm can be assessed successfully. The maximum error of the measurement is within 6% among the four samples. Furthermore, the uncertainty analysis of three standard deviations is conducted. Thus, the method is cost-effective to prevent damage for valuable photomasks in the flat panel display industry.

An innovative concrete that incorporates the advantages of self-compacting concrete with geopolymer is called self-compacting geopolymer concrete. The objective of this study was the Manufacturing of M30-grade self-compacting geopolymer concrete by adding industrial materials like fly ash (FA), ultrafine ground granulated blast furnace slag (UFGGBS), and silica fume (SF) as minerals. The disposal of these industrial wastes can be substantially overcome, as they lead to land pollution. The fixed powder content was 500 kg/m³. A mixture of sodium silicate (Na₂SiO₃) and sodium hydroxide (NaOH) created an alkaline solution that activated the cementitious binders. In this study, slump flow, L-box, V Funnel, T50 V Funnel, and J ring tests were carried out to determine the fresh qualities of the concrete. These tests were conducted under the regulations for self-compacting concrete provided by EFNARC (2005). To improve the flexural strength of the SCGC, 1.5 % glass fibre was added. This study illustrates how an artificial neural network (ANN) model can determine the concrete mix proportion. The characteristics of SCGC, both fresh and hardened properties test were investigated for molarities of 8, 10, and 12. The microstructural outcomes were determined using Fourier-transform infrared spectroscopy (FT-IR), scanning electron microscopy (SEM), and X-ray diffraction (XRD).

The sensitivity of macroscopic mechanical and thermal properties of grey cast iron is computationally investigated for a variety of graphite microstructures over a wide temperature range. In order to represent common graphite microstructures according to DIN EN ISO 945-1, a synthetic approach is used to algorithmically generate simulation domains. The developed mechanical and thermal model is applied in a large simulation study. The study includes statistical volume elements of the graphite microstructures classes GG-15 and IA2 to IA5, with 10 v.-%, 11 v.-% and 12 v.-% graphite, respectively, for a temperature range from 20 °C to 750 °C. Homogenized macroscopic quantities such as the Young's moduli, Poisson's ratios, yield strengths and thermal conductivities are predicted for the different microstructure classes by applying simulation and data analysis tools of the research data infrastructure Kadi4Mat.

We measured the anelastic, dielectric and structural properties of the metal-free molecular perovskite (ABX$_{3}$) (MDABCO)(NH$_{4}$)I$_{3}$, which has already been demonstrated to become ferroelectric below $T_{\text{C}}=$ 448~K. Both the dielectric permittivity measured in air on discs pressed from powder and the complex Young's modulus measured on resonating bars in vacuum show that the material starts deteriorating with loss of mass just above $T_{\text{C}}$, introducing defects and markedly lowering $T_{\text{C}}$. The elastic modulus softens of 50\% when heating through the initial $T_{\mathrm{C}}$, contrary to usual ferroelectrics, which are stiffer in the paraelectric phase. This suggests improper ferroelectricity, where the primary order parameter of the transition is not the electric polarization, but the orientational order of the MDABCO molecules. The degraded material presents thermally activated relaxation peaks in the elastic energy loss, whose intensities increase together with the decrease of ~$T_{\mathrm{C}}$. The peaks are much broader than pure Debye, due to the general loss of crystallinity, also apparent from X-ray diffraction, but their relaxation times have parameters typical of point defects. It is argued that the major defects should be of the Schottky type, mainly due to the loss of (MDABCO)$^{2+} $ and I$^{-}$, leaving charge neutrality, and possibly also (NH$_{4}$)$^{+}$ vacancies. The focus is on an anelastic relaxation process peaked around 200~K at $\sim 1$~kHz, whose relaxation time follows the Arrhenius law with $\tau $$_{0}$~$\sim $\ $10^{-13}$\ s and $E\simeq 0.4$~eV. This peak is attributed to I vacancies (V$_{\text{X}}$) hopping around MDABCO vacancies (V$_{\text{A}}$) and its intensity presents a peculiar dependence on temperature and content of defects. The phenomenology is thoroughly discussed in terms of lattice disorder introduced by defects and of partition of V$_{\text{X}}$ among sites that are far from and close to the cation vacancies. A method is proposed for calculating the relative concentrations of V$_{\text{X}}$, that are untrapped, paired with V$_{\text{A}}$ or forming V$_{\text{X}}$--V$_{\text{A}}$--V$_{\text{X}}$ complexes.

In this research, we investigate the bending of photon light and/or time-like geodesics within the context of four-dimensional space-time geometry, specifically in the presence of topological defects. These topological defects manifest as cosmic string space-time configurations, encompassing screw dislocation, spiral dislocation, and spacelike dislocation. Our primary objective is to determine the extent of deflection experienced by light-like and time-like geodesics and analyze how this deflection is affected by the cosmic string parameter, screw dislocation parameter, and spacelike dislocation parameter. To accomplish this, we employ a derivation technique that centers on the observation that photon rays (light-like geodesics) and/or time-like geodesics follow paths parallel to the z-axis while maintaining a constant radius along the cylinder.

The surface defects of shield subway tunnel can significantly affect the serviceability of the tunnel structure and may compromise the operation safety. To effectively detect the multiple surface defects, this research employs a tunnel inspection trolley (TIT) based on the mobile laser scanning technique. By conducting the inspection of the shield tunnel on a metro line section, various surface defects are identified by the TIT, including water leakage defect, dislocation, spalling, cross-section deformation, etc. To explore the root causes of the surface defects, the association rules between different defects are calculated via an improved Apriori algorithm. Results show that: i) there are significant differences in different association rules of various surface defects of the shield tunnel; ii) the average confidence of the association rule “dislocation & spalling → water leakage” is as high as 57.78%, indicating that most of the water leakage defects are caused by dislocation and spalling of the shield tunnel in the sections being inspected; iii) the weakest rule appears at “water leakage → spalling”, with the average confidence of 13%. The association analysis can be used in predicting the critical defects influencing the structural reliability and operation safety, such as water leakage, and optimizing the construction and maintenance work for the shield subway tunnel.

Advancements in genomics, bioinformatics and genome editing have uncovered new dimensions in gene regulation. Post-transcriptional modifications by the alternative splicing of mRNA transcripts are critical regulatory mechanisms of mammalian gene expression. In the heart, there is an expanding interest in elucidating the role of alternative splicing in transcriptome regulation. Substantial efforts have been directed towards investigating this process in heart development and failure. However, few studies have shed light on alternative splicing products and their dysregulation in congenital heart defects (CHDs). While elegant reports have shown the crucial roles of RNA binding proteins (RBPs) in orchestrating splicing transitions during heart development and failure, the impact of RBPs dysregulation or genetic variation on CHDs has not been fully addressed. Herein, we review the current understanding of alternative splicing and RBPs’ roles in heart development and CHDs and discuss the impacts of perinatal splicing transition and its dysregulation in CHDs. We further summarize discoveries made of causal splicing variants in key transcription factors that have been implicated in CHDs. Improved understanding of the roles of alternative splicing in heart development and CHDs may potentially inform novel preventive and therapeutic advancements for newborn infants with CHDs.

Urban trees are often more sun- and wind-exposed than their forest-grown counterparts. These environmental differences can impact how many species grow – impacting trunk taper, crown spread, branch architecture, and other aspects of tree form. Given these differences, windthrow models derived from traditional forest production data sources may not be appropriate for urban forest management. Additionally, visual abnormalities historically labeled as “defects” in timber production may not have a significant impact on tree failure potential. In this study, we look at urban tree failures associated with Hurricane Irma in Tampa, Florida, USA. We used spatial analysis to determine if patterns of failure existed among our inventoried trees. We also looked at risk assessment data to determine which visual defects were the most common and the most likely to be associated with branch or whole-tree failure. Results indicate that there was no spatial pattern associated with the observed tree failures – trees failed or withstood the storm as individuals. While some defects like decay and dead wood were associated with increased tree failure, other defects like weak branch unions and poor branch architecture were less problematic.

The evaluation of geometric defects is necessary in order to maintain the integrity of structures over time. These assessments are designed to detect damages of structures and ideally help inspectors to estimate the remaining life of structures. Current methodologies for monitoring structural systems, while providing useful information about the current state of a structure, are limited in the monitoring of defects over time and in linking them to predictive simulation. This paper presents a new approach to the predictive modeling of geometric defects. A combination of segmented from point clouds are parametrized using the convex hull algorithm to extract features from detected defects, and a stochastic dynamic model is then adapted to these features to model the evolution of the hull over time. Describing a defect in terms of its parameterized hull enables consistent temporal tracking for predictive purposes, while implicitly reducing data dimensionality and complexity as well. In this study, 2D point clouds analogous to information derived from point clouds were first generated over simulated life-cycles. The evolutions of point cloud hull parameterizations were modeled as stochastic dynamical processes via autoregressive integrated moving average (ARIMA) and vectorized autoregression (VAR) and compared against ground truth. The results indicate that this convex hull approach provides consistent and accurate representations of defect evolution across a range of defect topologies and is reasonably robust to noisy measurements, however assumptions regarding the underlying dynamical process play a significant the role in predictive accuracy. The results were then validated on experimental data from fatigue testing with high accuracy. Longer term, the results of this work will support finite element model updating for predictive analysis of structural capacity.

GCTs are developmental tumors and likely to reflect ontogenetic and teratogenetic determinants. The objective was to identify syndromes with or without congenital anomalies and non-syndromic defects as potential risk factors. Patients with extracranial GCTs (eGCTs) registered in MAKEI 96/MAHO 98 between 1996 and 2017 were used. According to Teilum's holistic concept malignant and benign teratomas were registered. We used a case control study design with Orphanet as a reference group for syndromic defects and the Mainz birth registry (EUROCAT) for congenital anomalies at birth. Co-occurring genetic syndromes and/or congenital anomalies were assessed accordingly. Odds ratios and 95% confidence intervals were calculated and p-values for Fisher’s exact test with Bonferroni correction if needed. A strong association was confirmed for Swyer (OR 338.6, 95% CI 43.7-2623.6) and Currarino syndrome (OR 34.2, 95% CI 13.2-88.6). We additionally found 17 isolated cases of eGCT with a wide range of syndromes, however not significantly associated following Bonferroni correction. All these cases pertained to girls. Regarding non-syndromic defects, no association with eGCTs could be identified. In our study we confirmed a strong association for Swyer and Currarino syndromes with additional congenital anomalies.

In this paper, we explore the hypothesis that topological defects formed in the quark-gluon plasma (QGP) of the early universe, specifically flux tubes and domain walls, could serve as stable dark matter candidates. Theoretical analysis of the QCD vacuum structure reveals that these defects can form due to nontrivial topological configurations, with the Lagrangian density incorporating topological terms. We model the formation and stability of flux tubes and domain walls, estimating their energy densities and dynamics within the QGP. Flux tubes, with energy per unit length approximately given by $\mu \approx \frac{\sigma}{g_s^2}$, and domain walls, characterized by a surface energy density $\sigma_{\text{DW}} \sim \Lambda_{\text{QCD}}^3$, exhibit unique gravitational signatures. These signatures include distinct gravitational lensing patterns due to their linear and planar mass distributions, making them detectable through astrophysical surveys. Furthermore, their minimal interaction with conventional matter aligns well with observational constraints on dark matter properties. We discuss potential experimental approaches for detecting these defects, including high-energy collider experiments and detailed analysis of gravitational lensing data. Our findings suggest that topological defects in the QGP provide a compelling and novel solution to the dark matter problem, offering a new direction for both theoretical investigation and experimental verification.

LSM4 is an essential yeast gene encoding a component of different LSM complexes involved in the regulation of mRNA splicing, stability and translation. In previous papers we reported that the expression in S. cerevisiae of the K. lactis Lsm4 gene lacking the C-terminal Q/N-rich domain in a Lsm4 null strain S. cerevisiae (Sclsm4D1) restored cell viability. Nevertheless, in this transformed strain we observed some phenotypes which are typical markers of regulated cell death, Reactive Oxygen Species and oxidated RNA accumulation. In this paper we report that a similar truncation operated in the S. cerevisiae LSM4 gene confers to cells the same phenotypes observed with the K.lactis LSM4D1 gene. Up to now there was no evidence on the direct involvement of LSM4 in autophagy. Here we found that the Sclsm4D1 mutant showed defects in the induction of autophagy and it was very sensitive to nitrogen starvation or treatment with low doses of rapamycin, an inducer of autophagy. Moreover, both during nitrogen starvation and ageing, the Sclsm4D1 mutant accumulated cytoplasmic autophagy-related structures, suggesting a role of Lsm4 in Phagophore Assembly Site (PAS) processing and/or vacuolar autophagosome internalization

Clients are increasingly looking for fast and effective means to quickly and frequently survey and communicate the condition of their buildings so that essential repairs and maintenance work can be done in a proactive and timely manner before it becomes too dangerous and expensive. Traditional methods for this type of work commonly comprise of engaging building surveyors to undertake a condition assessment which involves a lengthy site inspection to produce a systematic recording of the physical condition of the building elements, including cost estimates of immediate and projected long-term costs of renewal, repair and maintenance of the building. Current asset condition assessment procedures are extensively time consuming, laborious, and expensive and pose health and safety threats to surveyors, particularly at height and roof levels which are difficult to access. We propose a method for automated detection and localisation of key building defects from images using deep learning and convolution neural networks. The proposed model is based on a pre-trained VGG-16 classifier with Class Activation Mapping (CAM) for object localisation. The model has proven to be robust and able to accurately detect and localise mould growth, stains, and paint deterioration defects arising from dampness in buildings. The approach is being developed with potentials to scale-up to support automated detection of defects and deterioration of buildings in real-time using mobile devices and drones.

Defectively manufactured and deliberately damaged composite laminates fabricated with different continuous reinforcing fibres (respectively, carbon and glass) and polymer matrices (respectively, thermoset and thermoplastic) were inspected in magnetic resonance imaging equipment. Two pulse sequences were evaluated during non-destructive examination conducted in saline solution-immersed samples to simulate load-bearing orthopaedic implants permanently in contact with biofluids. The orientation, positioning, shape, and especially the size of translaminar and delamination fractures were determined according to stringent structural assessment criteria. The spatial distribution, shape, and contours of water-filled voids were sufficiently delineated to infer the amount of absorbed water if thinner image slices than this study were used. The surface texture of composite specimens featuring roughness, waviness, indentation, crushing, and scratches was outlined, with fortuitous artefacts not impairing the image quality and interpretation. Low electromagnetic shielding glass fibres delivered the highest, while electrically conductive carbon fibres produced the poorest quality images, particularly when blended with thermoplastic polymer, though reliable image interpretation was still attainable.

Cement paste backfill (CPB) is an effective waste management method allowing the storage of fine process tailings into underground mined-out voids. CPB performance generally depends on the sulfur content of the tailings and the type of binder. In recent years, there has been an in-creasing trend on the use of alkali-activated slag (AAS) to improve the performance properties of CPB. This study focuses on the ultrasonic and microstructural investigation of the effect of slag fineness on the mechanical, geochemical and durability properties of CPB made up of AAS (AAS-CPB) over 360 days. In this scope, AAS-CPB samples were prepared at three different fineness (3100-4650-6300 cm2/g). Fineness of slag significantly improved the early age- and long-term strength (~2.3 fold and ~6.6 fold, respectively) of CPB. However, further increase of slag fineness may have adverse effect on CPB microstructure and strength in the long term. Ultrasonic pulse velocity monitoring displayed very high relation with the strength evolution and durability assessment of CPB. Slag fineness at a degree was seen to improve the pore structure evolution of AAS-CPB. Microstructural studies are in good agreement with the geochemical and durability behavior of AAS-CPB. Microstructural and ultrasonic findings suggest that while slag fineness enhances the mechanical properties of AAS-CPB, further increase of the fineness of slag has no additional important technical advantages.

: In the automotive industry, high-strength plates have been increasingly used to reduce the vehicle body weight due to stringent regulations on fuel economy and safety. Such plates achieve tensile strengths as high as 1.5 GPa owing to the hot-stamping process. However, these plates suffer from scale generation and surface decarburization because of the surface oxidation of the material. Recently, studies on materials subjected to high-frequency induction heating have reported strength improvement owing to the coil shape and cooling method. This study presents the surface temperature changes, mechanical properties, and microstructures of boron steels subjected to longitudinal heating, which uses eddy currents generated from high-frequency induction heating. The surface temperature data were analyzed under different high-frequency induction heating powers (15, 18, 21, 24, 27, and 30 kW) and distances from the specimen (6, 9, and 15 mm). The mechanical properties and microstructures were also analyzed in different high-frequency induction heating coil directions. The correlations between the high-frequency induction heating power and the distance from the specimen with the maximum tensile strength were determined.

Nowadays, diamonds are widely used in science and technology. However, the properties of diamonds due to their defects are not fully understood. In addition to optical methods, positron annihilation spectroscopy (PAS) can be successfully used to study defects in diamonds. Positrons are capable of detecting vacancies, small and large clusters of vacancies induced by irradiation, by providing information about their size, concentration, and chemical environment. By mapping in the infrared (IR) range, it is possible to consider the admixture composition of the main inclusions of the whole plate. The article presents the results of the study of defects in synthetic diamond plates, one of which was irradiated by electrons. Presents data about the distribution of the defect concentration obtained by Infrared spectroscopy. PAS with a monochromatic positron beam can be used as a non-destructive technique of detecting defects (vacancy) distribution over the depth of diamond plates.

In this study, carbon blocks were fabricated using isotropic coke and coal tar pitch as raw materials, with a variation in pressure during cold isostatic pressing (CIP). The CIP pressure was set to 50, 100, 150, and 200 MPa, and the effect of the CIP pressure on the mechanical and electrical properties of the resulting carbon blocks was analyzed. Microstructural observations confirmed that after the kneading, the surface of isotropic coke was covered with the pitch components. Subsequently, after the CIP, granules, which were larger than isotropic coke and the kneaded particles, were observed. The formation of these granules was attributed to the coalescence of kneaded particles under the applied pressing pressure. This granule formation was accompanied by the development of pores, some remaining within the granules, while others were extruded, thereby existing externally. The increase in the applied pressing pressure facilitated the formation of granules, and this microstructural development contributed to enhanced mechanical and electrical properties. At a pressing pressure of 100 MPa, the maximum flexural strength was achieved at 33.3 MPa, and the minimum electrical resistivity was reached at 60.1 μΩm. The higher the pressing pressure, the larger the size of the granules. Pores around the granules tended to connect and grow larger, forming crack-like structures. This microstructural change led to degraded mechanical and electrical properties. The isotropic ratio of the carbon blocks obtained in this study was estimated based on the coefficient of thermal expansion (CTE). The results confirmed that all carbon blocks obtained proved to be isotropic. In this study, a specimen type named CIP-100 exhibited the best performance in every aspect as an isotropic carbon block.

Epitaxial lithium ferrite (LiFe5O8) films with different thicknesses have been successfully fabricated on SrTiO3 (001) substrates by magnetron sputtering deposition technique. The microstructural and magnetic properties are characterized by advanced transmission electron microscope and magnetic measurement device. It was found that the formation of structural defects can be influenced by the thickness of the film. Apart from the misfit dislocations, the orientation domains form in thinner film and twin boundaries appear in thicker film, respectively, contributing to the misfit strain relaxation in the heterosystem. The magnetic measurement shows that the thinner films have enhanced magnetization and a relatively lower coercive field compared with the thicker films containing the antiferromagnetic twin boundaries. Our results provide a way for tuning the microstructure and magnetic properties of lithium ferrite films by changing the film thickness.

The flow stress of face-centered cubic (FCC) metals exhibits a rapid increase near a strain rate of 104 s-1 under fixed strain conditions. However, many existing constitutive models either fail to capture the mechanical characteristics of this plastic deformation or use piecewise strain rate hardening models to describe this phenomenon. Unfortunately, the piecewise models may suffer from issues such as discontinuity of physical quantities and difficulties in determining segment markers, and struggling to reflect the underlying physical mechanisms that give rise to this mutation phenomenon. In light of this, this paper proposes that the abrupt change in flow stress sensitivity to strain rate in FCC metals can be attributed to microstructural evolution characteristics. To address this, a continuous semi-empirical physical constitutive model for FCC metals is established based on the microstructural size evolution proposed by Molinari-Ravichandran and the dislocation motion slip mechanism. This model effectively describes the mutation behavior of strain rate sensitivity under fixed strain, particularly evident in the annealed OFHC. The predicted results of the model across a wide range of strain rates (10-4 − 106 s-1) and temperatures (77 − 1096 K) demonstrate relative errors generally within ±10% of the experimental values. Furthermore, the model is compared to five other models, including Mechanical Threshold Stress (MTS), Nemat-Nasser-Li (NNL), Preston-Tonks-Wallace (PTW), Johnson-Cook (JC), and Molinari-Ravichandran (MR) models. A comprehensive illustration of errors reveals that the proposed model outperforms the other five models in describing the plastic deformation behavior of OFHC. The error results offer valuable insights for selecting appropriate models for engineering applications and provide significant contributions to the field.

The spontaneous combustion of coal in goaf is the main cause of mine fire at present. Lignite has become a major hidden danger in mine production safety because of its easy oxidation. In this paper, an innovative strategy was proposed to inhibit the spontaneous combustion of lignite by using the principle of microbial-induced calcium deposition. Based on the optimized culture method, a novel composite inhibitor of Bacillus pasteurelli was prepared. SEM, pore size analysis and FT-IR experiments were carried out simultaneously, and the oxidation properties of lignite before and after inhibition were quantitatively characterized from the perspective of microstructure, and the flame retardant properties of microbial and chemical retardants on coal samples were compared. The results show that a large number of deposited calcium carbonate particles are obviously attached to the surface of lignite after microbial inhibition treatment, which plays a physical oxygen insulation role. At the same time, the total pore volume and specific surface area of the coal sample decreased by 68.49% and 74.01%, respectively, indicating that microbial inhibitors can effectively plug the primary pores of lignite. Based on the peak measurement of 400-4000cm-1 infrared spectrum of coal samples, it is found that the contents of active groups including hydroxyl, carboxyl and methyl/methylene in lignite molecules after microbial inhibition are lower than those in raw coal, especially the methyl/methylene content involved in the initial oxidation reaction decreased by 96.5% compared with the baseline content in raw coal. The results show that the oxidation and self-heating capacity of lignite after microbial inhibition is effectively restrained in the initial spontaneous combustion. The research results of this paper can provide effective solutions for the prevention and control of coal spontaneous combustion risk in mined-out area.

In the perspective of designing complex concentrated alloys (CCAs) for structural applications, sigma (σ) phase is important. It is generally known to be an embrittling phase leading to a degradation in the mechanical properties of CCAs. This necessitates detailed investigations on the evolution of σ phase in these alloys. In the present study, an equiatomic CoCrCuMnNi CCA is chosen, in which σ phase appears at 800°C, as reported in a recent publication [1]. To this end, the present investigation aims at understanding the evolution of this phase so that its presence can be controlled for the purpose of preventing degradation in mechanical properties. In the present work, a vacuum arc melted alloy, after homogenisation (at 400°C for 5h), is heat-treated for different times ranging from 1 to 9h at 800°C followed by water quenching. Extensive characterisation has been carried out using X-Ray Diffraction (XRD) and Scanning Electron Microscopy (SEM) and Transmission Electron Microscopy (TEM) techniques to understand the sequence of σ phase precipitation at 800°C.

The radiation-induced optical absorption at 1.5-5.5 eV (up to the beginning of fundamental absorption) has been analyzed in CVD diamond disks exposed to 231-MeV 132Xe ions with four fluences from 1012 to 3.81013 cm-2. The 5-mm diameter samples (thickness 0.4 mm) were prepared by Diamond Materials, Freiburg (Germany), average grain size at growth site was around 80 m, the range of xenon ions was R= 11.5 m. The intensity of several bands grows with ion fluence thus confirming radiation-induced origin of the defects responsible for these bands. The recovery of radiation damage has been investigated via isochronal (stepwise) thermal annealing procedure up to 650°C, while all spectra were measured at room temperature. Based on these spectra, the annealing kinetics of several defects, in particular carbon vacancies (GR1 centers with a broad band 2 eV) and complementary C-interstitial-related defects ( 4 eV), as well as vacancies located nearby nitrogen substitutional atoms (narrow bands around 2.5 eV) have been constructed. The experimental kinetics have also been analyzed in terms of the diffusion-controlled bimolecular reactions. The migration energies of tentatively interstitial atoms (mobile components in recombination process) are obtained, their dependence on the irradiation fluences is discussed.

Nemaline myopathy (NM) is one of the most common forms of congenital myopathy and it is identified by the presence of "nemaline bodies" (rods) in muscle fibers by histopathological exam-ination. The most common forms of NM are caused by mutations in the ACTA1 (Actin Alpha 1) and NEB (Nebulin) genes. Clinical features include hypotonia and muscle weakness. Unfortunate-ly, there is no curative treatment and the pathogenetic mechanisms remains unclear. In this man-uscript, we examined the pathophysiological alterations in NM using dermal fibroblasts derived from patients with mutations in ACTA1 and NEB genes. Patients’ fibroblasts were stained with rhodamine phalloidin to analyze the polymerization of actin filaments by fluorescence microsco-py. We found that patients' fibroblasts showed incorrect actin filament polymerization compared to control fibroblasts. Actin filament polymerization defects was associated with mitochondrial dysfunction. Furthermore, we identified two mitochondrial boosting compounds, linoleic acid (LA) and L-carnitine (LCAR), that improved the formation of actin filaments in mutant fibro-blasts and corrected mitochondrial bioenergetics. Our results indicate that cellular models can be useful to study the pathophysiological mechanisms involved in NM and to find new potential therapies. Furthermore, targeting mitochondrial dysfunction with LA and LCAR can revert the pathological alterations in NM cellular models.

The cast defects strongly degrade the mechanical properties in cast alloys. The effect of Sn addition on Al-Si alloys was investigated by 3D computed tomography, SEM and TEM. Amorphous Sn oxides are found near the alumina film, cause more shrinkage pores, initiate cracks and deteriorate mechanical properties. This work suggests not adding Sn in various Al alloys used in cast state.

Mitochondrial disorders, although heterogeneous, are traditionally described as conditions characterized by encephalomyopathy, hypotonia and progressive postnatal organ failure. Here we provide a systematic review of Linear Skin Defects with Multiple Congenital Anomalies (LSDMCA), a rare unconventional mitochondrial disorder which presents as a developmental disease; its main clinical features include microphthalmia with different degrees of severity, linear skin lesions, and central nervous system malformations. The molecular basis of this disorder has been elusive for several years. Mutations were eventually identified in three X-linked genes, i.e., HCCS, COX7B, and NDUFB11, which are all endowed with defined roles in the mitochondrial respiratory chain. A peculiar feature of this condition is its inheritance pattern: X-linked dominant male-lethal. Only female or XX male individuals can be observed, implying that nullisomy for these transcripts is incompatible with normal embryonic development in mammals. All three genes undergo X-inactivation that, according to our hypothesis, may contribute to the extreme variable expressivity observed in this condition. We propose that mitochondrial dysfunction should be considered as an underlying cause in developmental disorders. Moreover, LSDMCA should be taken into consideration by clinicians when dealing with patients with microphthalmia with or without associated skin phenotypes.

Existing methods for detecting magnetic leakage signals from damaged wire ropes require axial saturation magnetisation, and the accuracy of the detection equipment depends on the saturation degree of magnetisation. Moreover, the expected magnetisation effect is usually difficult to achieve owing to the special characteristics of the rope structure, diameter, and operating environment of the wire rope. Consequently, in addition to other issues, the detection accuracy and versatility of the equipment are low. In this study, a method based on spatial multidimensional orthogonal array loop magnetisation for detecting mine wire rope defects is proposed. Firstly, a new sensor excitation structure model is developed. Then a method of radiant magnetic flux of permanent magnet array is analysed, and the influence law of the number of permanent radiant magnetic blocks on the magnetisation effect is studied. In addition, a method of wire rope detection based on the principle of clustering is investigated, according to which the influence law of the shape, structure, and size of the polyurethane device on the effect of magnetisation is discussed. Finally, through laboratory experiments, the test model and proposed method are verified. The results show that the magnetisation effect is better and more cost-effective when the number of permanent magnet radiation magnetic block is n=8, and the proposed detection method can effectively distinguish damaged wire rope joints. Furthermore, the proposed equipment achieved signal-to-noise ratio of the signals, improving the reliability of damage detection.

Laser shock peening as an innovative surface treatment technology can effectively improve the fatigue life, sur-face hardness, corrosion resistance, and residual compressive stress. Compared with the laser shock peening, the warm laser shock peening (WLSP) is a new surface treatment technology to improve materials’ surface performances, which takes advantage of thermal mechanical effects on stress strengthening and micro-structure strengthening, results in more stable distribution of the residual compressive stress under heating and cyclic loading process. In this paper, the microstructure of GH4169 nickel super-alloy processed by WLSP technology with differ-ent laser parameters were investigated. The proliferation and tangling of dislocations in GH4169 were observed and the dislocation density increased after WLSP treatment. The influences of different treatment by LSP and WLSP on the microhardness distribution of the surface and along cross-sectional depth were investi-gated. The microstructure evolution of the GH4169 alloy being shocked with WLSP were studied by TEM. The effect of temperature on the stability of high temperature microstructure and properties of GH4169 alloy WLP was investigated.

The objective of this study is to conduct a mineralogical and chemical characterization of the mortars Roman archaeological site of Volubilis to rebuild spare mortars for restoration. We take samples of mortar, broken tile palate garden, and pavement mosaic Falavius Germanus houses. The analysis by X-ray diffraction reveals the coarse mortar Flavius Germanus is made of quartz and calcite with feldspar and probably, mica and dolomite in small amounts. The binder end is formed calcite and quartz. However, the broken tile mortar is formed by coarse particles, clay base mixed with a binder phase dominated by calcite. These results allowed us to reformulate spare mortars for the restoration of damaged Roman mosaics. The mortars are made up by 63.6% of lime and 36.4% of sand(with 4.19% of large grain, 71, 04% of coarse sand, 24.22%, of fine sand and 0.55% fines parts).The performance of these mortars was tested by mechanical testing.

This study investigates the effect of scaffold architecture on bone regeneration, focusing on 3D-printed polylactic acid-bioceramic calcium phosphate (PLA-bioCaP) composite scaffolds in rabbit femoral condyle critical defects. To assess their influence on bone healing and scaffold performance, we explored two distinct scaffold designs, alternate and helical laydown patterns. The scaffolds were meticulously characterized for pore size, strut thickness, porosity, pore accessibility, and mechanical properties. The in vivo efficacy of these scaffolds was evaluated using a rabbit femoral condyle critical defect model. Our findings indicate that both scaffold architectures are biocompatible and support bone formation. The helical scaffolds, characterized by larger pore sizes and higher porosity, demonstrated significantly greater bone regeneration than the alternate structures. However, their lower mechanical strength presented limitations for use in load-bearing sites. This study highlights the importance of scaffold architecture in bone tissue engineering and underscores the need to balance porosity and mechanical strength for optimal bone regeneration. The findings provide crucial insights for the design of 3D- printed scaffolds in clinical applications, particularly in the context of critical-sized bone defects. The study also outlines potential areas for future research, including exploring hybrid scaffold designs to achieve optimal porosity without compromising mechanical integrity.

Biomimetic foods are expected to have potential health benefits for the management and prevention of chronic diseases, such as diabetes and cardiovascular disease. In the current research, two commercially available and affordable plant proteins (soy protein isolate-SPI and pea protein isolate-PPI) at two levels (5%, 10%) were added to the Yangyu jiaotuan with an objective to develop a product with reduced glycemic properties and high protein content while maintaining its original taste and texture. The results showed that several important textural properties such as hardness and chewiness did not change significantly during the refrigerated storage. The storage modulus G′ increased with refrigerated storage time for different samples, there were significant differences among the five samples (with and without protein addition) with respect to frequency dependence during rheological measurements. The in vitro starch digestion experiments showed that the starch hydrolysis of Yangyu jiaotuan decreased considerably with the increase in PPI content and during refrigerated storage due to starch retrogradation. Protein has protected the microstructure and there was less damage when compared to samples without protein. The bimodal peaks of the particle size distribution curves showed that the newly developed Yangyu jiaotuan contains two different sizes of particles, the smaller particles (~30 μm) corresponded to PPI and starch granules, while the larger particles corresponded to the fragments of gel network of the starch matrix. Based on the above results, Yangyu jiaotuan mixed with pea protein is a convenient potato staple food product, which complies with the biomimetic potato food very well.

Development of rovers and development of infrastructure which enables them to probe other planets (such as Mars) have sparked a lot of interest recently specially with increasing public attention in Moon and Mars program by National Aeronautics and Space Administration. This is designed to be achieved by various means such as advanced spectroscopy and artificial intelligent techniques such as deep learning and transfer learning to enable the rover to not only map the surface of planet but to get a detailed information about its chemical makeup in layers beneath (deep learning) and in areas around point of observation (transfer learning). In this work, which is part of a proposal, later approach is explored. A systematic strategy is presented which make use of aforementioned techniques developed for metallic glass matrix composites as benchmark and helps develop algorithms for chemistry mapping of actual Martian surface on Perseverance Rover launching shortly.

This paper focuses on the impact of defects density and carrier capture cross-section area in the electron transport material (ETM), hole transport material (HTM), and absorber layers on the performance of perovskite solar cells and quantum efficiency (QE). Furthermore, the impact of defects density at the interface between ETM/absorber and absorber/HTM is also studied. SCAPS-1D software is used in the current study in determining solar cell performance. The proposed perovskite solar cell structure is a planar FTO/TiO2/ CH3NH3PbI3/ Cu2O. The results indicated that increasing the defect density in the absorber layer significantly affects cell performance, while in ETM and HTM layers, the cell parameters remain unaffected. It is also found that the defect capture cross-section has a similar behavior to the defect density in the main layers (ETM, absorber, and HTM). In addition, it is observed that by increasing the defects density in the ETM/absorber and absorber/HTM interfaces layer, the cell parameters FF, Jsc, and PCE have been slightly decreased, with no effect on Voc. Moreover, it is also noted that the quantum efficiency QE is sharply reduced. Finally, this paper introduced the correlation between the defect density and the capture cross-section, which is the first attempt to find such a relationship in perovskite solar cells to the knowledge of the authors.

We explore the implementation of specific optical properties of armchair graphene nanoribbons (AGNRs) through edge-defect manipulation. This technique employs the tight-binding model in conjunction with the calculated absorption spectral function. Modification of the edge states gives rise to the diverse electronic structures with striking changes in the band gap and special flat bands at low energy. The optical-absorption spectra exhibit exotic excitation peaks and they strongly depend on the type and period of the edge extension. Remarkably, there exist the unusual transition channels associated with the flat bands for selected edge-modified systems. We discover the special rule governing how the edge-defect influences the electronic and optical properties in AGNRs. Our theoretical prediction demonstrates an efficient way to manipulate the optical properties of AGNRs. This might be of importance in the search for suitable materials designed to have possible technology applications in nano-optical, plasmonic and optoelectronic devices.

Aluminum profile surface defects can greatly affect the performance, safety and reliability of products. Traditional human-based visual inspection is low accuracy and time consuming, and machine vision-based methods depend on hand-crafted features which need to be carefully designed and lack robustness. To recognize the multiple types of defects with various size on aluminum profiles, a multiscale defect detection network based on deep learning is proposed. Then, the network is trained and evaluated using aluminum profile surface defects images. Results show 84.6%, 48.5%, 96.9%, 97.9%, 96.9%, 42.5%, 47.2%, 100%, 100%, 43.3% average precision(AP) for the ten defect categories, respectively, with a mean AP of 75.8%, which illustrate the effectiveness of the network in aluminum profile surface defects detection. In addition, saliency maps also show the feasibility of the proposed network.

Iron is the most abundant micronutrient in plant mitochondria and it has a crucial role in biochemical reactions involving electron transfer. It has been described in Oryza sativa that Mitochondrial Iron Transporter (MIT) is an essential gene and that knockdown mutant rice plants have a decreased amount of iron in mitochondria, strongly suggesting that OsMIT is involved in mitochondrial iron uptake. In Arabidopsis thaliana, two genes encode MIT homologues. In this study, we analyzed different AtMIT1 and AtMIT2 mutant alleles, confirming that individually AtMIT1 nor AtMIT2 genes are essential. When we generated crosses between Atmit1 and Atmit2 alleles we were able to isolate homozygous double mutant plants. Interestingly, homozygous double mutant plants were obtained only when mutant alleles of Atmit2 with the T-DNA insertion in the intron region were used for crossings, and in these cases a correctly spliced AtMIT2 mRNA was generated, although at a low level. Atmit1 Atmit2 double homozygous mutant plants, which were knockout for AtMIT1 and knockdown for AtMIT2, were grown and chacterised in iron sufficient conditions. Pleiotropic developmental defects were observed including abnormal seeds, increased number of cotyledons, slow growth rate, pinoid stems, defects in flower structures and reduced seed set. We observed a possible phenomenon of T-DNA suppression in the next generation of Atmit1 Atmit2 double homozygous mutant plants, correlating with an increased splicing of the AtMIT2 intron containing the T-DNA. Molecular analysis of gene expression markers for mitochondrial and oxidative stress showed that Atmit1 Atmit2 double homozygous mutant plants express a degree of mitochondrial perturbation. A RNA-Seq study was performed and we could identify more than 760 genes differentially expressed in Atmit1 Atmit2, including genes involved in iron transport, coumarin metabolism, and hormones metabolism, transport and signaling. Our data suggest that some of the phenotypes observed in Atmit1 Atmit2 double homozygous mutant plants are mediated by defects in auxin homeostasis.

The material flow dynamic and velocity distribution on the melted domain surface play a crucial role on the joint quality and formation of welding defects. In this study, authors investigated the effects of the low and high currents of plasma arc welding on the material flow and thermodynamics of molten pool and its relationship to the welding defects. The high-speed video camera (HSVC) was used to observe the convection of the melted domain and welded-joint appearance. Furthermore, to consider the Marangoni force activation, the temperature on the melted domain was measured by a thermal HSVC. The results revealed that the velocity distribution on the weld surface was higher than that inside the molten weld pool due to the difference of the massive density between the air and the steel. Moreover, in the case of low welding current (80A) the convection speed of molten was faster than that of the high welding current case (160A) owing to the difference of main driving forces direction and strength, which leading to undercut and humping defects on the weld surface and excessive convex (burn-through) defect at the bottom weld side, respectively. The medium welding current (120A) had two convection patterns with the main flow in backward direction, which resulted in better welding quality without defect. The interaction between the shear force and Marangoni force played a solid state on the convection and heat transportation processes in the plasma arc welding process.

Despite being well established phenomena, solidification principles are experiencing tough challenges in their application to explain microscale transport phenomena in additive manufacturing melt pool. The problem becomes even more complicated when applied to multicomponent bulk metallic glass matrix composites (BMGMC) whose behavior is dubious and still not fully understood. The aim of the present study is to highlight pathways to overcome these challenges. A comprehensive nucleation and growth model based on original KGT theory and Rappaz modification is proposed encompassing actual transient thermophysical BMGMC data to predict evolving microstructure during additive manufacturing. The model is aimed at pictorial representation of in-situ ductile phase dendrite evolution from melt pool during solidification using two-dimensional cellular automaton (CA) methods. It is proposed to be coded in MATLAB® using commercial simulation code ABAQUS® at back end for macroscopic heat transfer model. The results will be compared with experimental values for validation.

A quantitative method is proposed to determine of Stone-Wales defects for carbon nanostructures with sp2 hybridization of carbon atoms. The technique is based on the diene synthesis reaction (Diels-Alder reaction). The proposed method was used to determine Stone-Wales defects in the few-layer graphene (FLG) nanostructures synthesized by the self-propagating high-temperature synthesis (SHS) process, in reduced graphene oxide (rGO) synthesized based on the method of Hammers and in the single-walled carbon nanotubes (SWCNT) TUBAL trademark, Russia. Our research has shown that the structure of FLG is free of Stone-Wales defects, while the surface concentration of Stone-Wales defects in TUBAL carbon nanotubes is 1.1×10-5 mol/m2 and 3.6×10-5 mol/m2 for rGO.

In addition to image filtering in the spatial and frequency domains, fractal characteristics induced algorithms offers considerable flexibility in the design and implementations of image processing solutions in areas such as image enhancement, image restoration, image data compression and spectrum of applications of practical interests. Facing up to a real-world problem of identifying workpiece surface defects, a generic adaptive fractal filtering algorithm is proposed, which shows advantages on the problems of target recognition, feature extraction and image denoising at multiple scales. First, we reveal the physical principles underlying between signal SNR and its representative fractal dimension indicative parameters, validating that the fractal dimension can be used to adaptively obtain the image features. Second, an adaptive fractal filtering algorithm (Abbreviated as AFFA) is proposed according to the identified correlation between the image fractal dimensions and the scales of objects, and it is verified by a benchmarking image processing case study. Third, by using the proposed fractal filtering algorithm, surface defects on a flange workpiece are identified. Compared to conventional image processing algorithms, the proposed algorithm shows superior computing simplicity and better performance Numerical analysis and engineering case studies show that the fractal dimension is eligible for deriving an adaptive filtering algorithm for diverse-scale object identification, and the proposed AFFA is feasible for general application in workpiece surface defect detection.

An effective method to inspect inaccessible nuclear power facility by interface wave which propagate along the shrink fit boundary of reactor head is proposed in this study. Reactor head is relatively thick to inspect from the outside of reactor by conventional ultrasonic testing. The proposed interface wave can propagate a long distance from the fixed transducer position. The inside of nuclear reactor is limited to access due to the high radiation, so transducers are located at outside of nuclear facility and interface wave propagates into the nuclear reactor for defect detection. The numerical simulation and experiments were carried out to validate the effectiveness of the proposed interface wave inspection method. Various defect cases simulating field failures are also presented with satisfactory detectability by the proposed technique with the features for defect classification.

Statistical modeling lies at the heart of product design and development throughout numerous engineering disciplines, especially since processing large amounts of data has become increasingly ubiquitous. While mathematical statistics provide elegant guidance pertaining to the question of whether or not some particular underlying modeling assumptions are justified and appropriate, when pursuing a more comprehensive assessment of product design and development other considerations often increase in significance. Therefore, we will examine and analyze the tedious interactions and implications of statistical modeling choices and product liability exposure. To the best of our knowledge, this paper is the first to draw attention to and explore some often overlooked or oversimplified dangers and pitfalls that enter the equation when product design heavily relies on statistical modeling. In particular, through a diligent analysis of both statistical and legal aspects we will explore how statistically optimal procedures may yield far from optimal outcomes in terms of product liability when applied to actual real life problems and why suboptimal nonparametric or robust approaches may constitute better alternatives.

Cytokinesis is accomplished in higher plants by the phragmoplast, creating and conducting the cell plate, to separate daughter nuclei by a new cell wall. The microtubule-severing enzyme p60-katanin plays an important role in the centrifugal expansion and timely disappearance of phragmoplast microtubules. Consequently, aberrant structure and delayed expansion rate of the phragmoplast occur in p60-katanin mutants. Here, the consequences of p60-katanin malfunction in cell plate/daughter wall formation were investigated by transmission electron microscopy (TEM), while deviations in the chemical composition of cell plate/new cell wall were identified by immunolabeling and confocal microscopy, in root cells of the fra2 Arabidopsis thaliana mutant. It was found that, apart from defective phragmoplast microtubule organization, cell plates/new cell walls appeared also faulty in structure, being unevenly thick and perforated by large gaps. In addition, demethylesterified homogalacturonans were prematurely present in fra2 cell plates, while callose content was significantly lower than in the wild-type. Furthermore, KNOLLE syntaxin disappeared from newly formed cell walls in fra2 earlier than in the wild-type. Taken together, these observations indicate that delayed cytokinesis, due to faulty phragmoplast organization and expansion, results in a loss of synchronization between cell plate growth and its chemical maturation.

Defects are considered one of the wastes in manufacturing systems that negatively affect the delivery times, cost and quality of products leading to manufacturing companies facing a critical situation with the customers and to not comply with the IPC-A-610E standard for the acceptability of electronic components. This is the case is a manufacturing company located in Tijuana, Mexico. Due to an increasing demand on the products manufactured by this company, several defects have been detected in the welding process of electronic boards, as well as in the components named Thru-Holes. It is for this reason that this paper presents a lean manufacturing application case study. The objective of this research is to reduce at least 20% the defects generated during the welding process. In addition, it is intended to increase 20% the capacity of 3 double production lines where electronic boards are processed. As method, the PDCA cycle, is applied. The Pareto charts and the flowchart are used as support tools. As results, defects decreased 65%, 79% and 77% in three analyzed product models. As conclusion, the PDCA cycle, the Pareto charts, and the flowchart are excellent quality tools that help decrease the number of defective components.

This study investigated defect formation and strain distribution in high Mg content Al-Mg alloys during normal rolling and cross-rolling processes. The finite element analysis (FEA) revealed the presence of wave defects and strain localization-induced zipper cracks in normal cold rolling, which were confirmed by experimental results. The concentration of shear strain played a significant role in crack formation and propagation. However, the influence of wave defects was minimal in the cross-rolling process, which exhibited a relatively uniform strain distribution. Nonetheless, strain concentration at the edge and center regions led to the formation of zipper cracks and edge cracks, with more pronounced propagation observed in the experiments compared to FEA predictions. Furthermore, texture evolution was found to be a crucial factor affecting crack propagation, particularly with the development of the Goss texture component which is observed by electron backscattered diffraction analysis at bending points. The Goss texture hindered crack propagation, while the Brass texture allowed cracks to pass through. This phenomenon was consistent with both FEA and experimental observations. To mitigate edge crack formation and propagation, potential strategies involve promoting the formation of the Goss texture at the edge through alloy and process conditions, as well as implementing intermediate annealing to alleviate stress accumulation. These measures can enhance the overall quality and reliability of Al-Mg alloys during cross-rolling processes. In summary, understanding the mechanisms of defect formation and strain distribution in Al-Mg alloys during rolling processes is crucial for optimizing their mechanical properties. The findings of this study provide insights into the challenges associated with wave defects, strain localization, and crack propagation. Future research and optimization efforts should focus on implementing strategies to minimize defects and improve the overall quality of Al-Mg alloys in industrial applications.

Quantification of bone loss for follow-up comparisons has not been routinely performed in patients with parietal thinning so far. This study compares different methodological approaches including both 2- and 3-dimensional methods in computerized tomographies of a single patient. The 2-dimensional method provides accurate measurements of bone thickness, while the 3-dimensional method allows for a more comprehensive view of the bone's structure, including parameters like shape, size, and thickness. The techniques provided valuable data for the treating physician and suggest a possible effect of corticosteroids in this individual patient. The study concludes that 3-dimensional reconstruction of computerized tomographies with subsequent 2-dimensional analyses appears justified for routine radiological practice to increase clinical awareness of the size of the parietal bone defects and allow for quantification of bone loss during long-term follow-ups. Further validation of the proposed analytical approaches is warranted in larger studies to investigate patterns of bone thinning across the skull and changes in bone volumes over time, with specialized software to be approved for such analyses.

When bone substitutes materials are used, the increased risk of infection due to the none-autogenic graft is often discussed. The treatment of large bone defects in geriatric patients, often with osteoporotic bone, often presents major challenges to surgery. Bone substitutes materials are available indefinitely without the risk of additional surgery in each patient. Can bone substitutes materials be used without hesitation in the geriatric patient?Eighty-three patients suffered traumatic fractures of the distal radius, proximal humerus, and proximal tibia. The defect zones were filled with bone substitute material based on nanocrystalline hydroxyapatite (NHA) or calcium phosphate (CP). For comparison, a reference group without the void filling with a bone graft substitute (void defects, ED) was studied. All patients over the age of 64 years were retrospectively evaluated for complications and radiological outcomes. Results: 106 patients sustained traumatic fractures of the distal radius (68.9%), proximal humerus (5.7%), and proximal tibia (22.6%). No differences in infections were found when comparing the groups (p=1.0). retrospectively evaluated. The KEM group had a nonsignificantly lower rate of pseudarthrosis (p=0.09). A relative risk (RR) reduction of complications of 32.64% was observed when bone grafting material was used. The NNT for the prevention of complications was 5.99. When bone healing was assessed by radiological images, some follow-up studies showed significant differences in fracture bridging (p<0.001).Conclusions: In contrast to previous studies, bone substitutes materials can support the healing process in geriatric patients without relevant disadvantages. With an NNT of 6 regarding complications, many patients could benefit from bone graft augmentation. No increased infection rate was observed.

When bone substitutes materials are used, the increased risk of infection due to the none-autogenic graft is often discussed. The treatment of large bone defects in geriatric patients, often with osteoporotic bone, often presents major challenges to surgery. Bone substitutes materials are available indefinitely without the risk of additional surgery in each patient. Can bone substitutes materials be used without hesitation in the geriatric patient? Eighty-three patients suffered traumatic fractures of the distal radius, proximal humerus, and proximal tibia. The defect zones were filled with bone substitute material based on nanocrystalline hydroxyapatite (NHA) or calcium phosphate (CP). For comparison, a reference group without the void filling with a bone graft substitute (void defects, ED) was studied. All patients over the age of 64 years were retrospectively evaluated for complications and radiological outcomes. Results: 106 patients sustained traumatic fractures of the distal radius (68.9%), proximal humerus (5.7%), and proximal tibia (22.6%). No differences in infections were found when comparing the groups (p=1.0). retrospectively evaluated. The KEM group had a nonsignificantly lower rate of pseudarthrosis (p=0.09). A relative risk (RR) reduction of complications of 32.64% was observed when bone grafting material was used. The NNT for the prevention of complications was 5.99. When bone healing was assessed by radiological images, some follow-up studies showed significant differences in fracture bridging (p<0.001). Conclusions: In contrast to previous studies, bone substitutes materials can support the healing process in geriatric patients without relevant disadvantages. With an NNT of 6 regarding complications, many patients could benefit from bone graft augmentation. No increased infection rate was observed.

Metallic glass matrix composites are unique new materials which have superior mechanical properties as compared to existing conventional materials. Owing to this, they are potential candidates for various future structural applications. However, they suffer from disadvantages of brittleness, poor ductility and little or no toughness and they manifest catastrophic failure on application of force. Their behavior is dubious and require extensive experimentation to draw conclusive results. In present study, which is continuation of previous study by author, an effort has been made to overcome this pitfall by simulation. A quantitative mathematical model based on KGT theory has been developed to describe nucleation and growth of crystalline phase dendrites in glassy matrix during solidification. It yields information about numerical parameters to understand the behavior of each individual element in a phase in multicomponent sluggish slurry and their effect on final microstructural evolution. Model is programmed and simulated in MATLAB®. Its validation is done by comparison with identical curves reported in literature previously for similar alloys. Results indicate that effect of incorporating all heat transfer coefficients at macroscopic level and diffusion coefficients at microscopic level play a vital role in refining the model and bringing it closer to actual experimental observations. Two types of hypoeutectic and eutectic systems namely Zr₆₅Cu₁₅Al₁₀Ni₁₀ and Zr_47.5Cu_45.5Al₅Co₂ respectively were studied. Simulation results were found to be in good agreement with prior simulated and experimental values

Magnesium ions play an important immune-regulatory role during bone repair. For this study, we prepared micro-nano bioactive glass containing magnesium, which can release magnesium, silicon, and calcium ions and has a positive impact on osteogenic differentiation and vascular regeneration. In this study, MgMNBG was compounded and combined with PLGA and PCL for 3D printing. Afterwards, the physicochemical properties and bone repair performance of the scaffolds were evaluated through in vitro and in vivo experiments. We also investigated the effects of MgMNBG on osteogenic differentiation, immune regulation, and vascular regeneration. The results showed that MgMNBG can inhibit inflammation and promote osteogenesis and angiogenesis by regulating macrophages. PLGA/PCL/MgMNBG scaffolds have good osteogenic and angiogenic effects, and the composite scaffolds have excellent bone repair performance and potential application value.

Heel pain in the “funnel-shaped” space between the calcaneus, talus, and talocalcaneonavicular and subtalar joints may be representative of Sinus Tarsi syndrome. The pain is often characterized by a burning, numbness, or tingling sensation that can stem from strains and tears on the ligaments in that area. Injury treatment typically includes balance training, muscle exercises, bracing, foot orthosis, and non-steroidal anti-inflammatory drugs (NSAIDs). This study presents Wharton Jelly (WJ) tissue allografts as an alternative intervention for patients who fail standard-care treatments. WJ targets tissue defects, unlike other therapies, which aim to reduce swelling and symptomatic pain. This study includes five female patients who have previously failed standard-of-care treatment. Each received extracorporeal pulse-activated therapy (EPAT), WJ, laser therapy, and an orthotic. After an average of 80 days, the cohort had an overall 85.29% improvement in pain. The study's limitations include a small cohort size and a non-blinded design. Given the significant improvement in pain, WJ tissue allograft, combined with other techniques, presents an optimal patient care plan for tissue defects associated with Sinus Tarsi syndrome when standard-of-care treatments fail. These results provide evidence for a more extensive, randomized study to define dosage protocols further and confirm safety and efficacy.

The main purpose of this study was to develop a model for predicting the quality of holes drilled in the root part of a spar of helicopter main rotor blades made of the Glass Fiber Reinforced Plastic (GFRP)-Ti multilayer polymer composite. As the main quality criterion, delaminations at the entry and exit of the drill from the hole were taken. In the experimental study a conventional drill and two modified geometry drills: a double-point angle drill and a dagger drill were used. Preliminary experiments showed the best hole quality when using modified drills, which allowed further detailed study only with both modified drills at different drilling speeds and feed rates. Its results in the form of training sets were used to build the Artificial Neural Networks (ANNs) to predict delamination at the entry and exit of drilled holes. The analysis of the fitted response functions, presented as 3D surfaces plots and superimposed contour plots, made it possible to choose the better tool - a double-point angle drill and determine the optimal area for drilling speed and feed rates, confirming that the prediction of the quality and productivity of machining composites based on ANN is an effective tool to search and quantify the quality criteria of such technologies.

In the current industrial revolution, advanced technologies and methods can be effectively utilized for the detection and verification of defects in high-speed steel filament production. This paper introduces an innovative methodology for the precise detection and verification of micro surface defects found in steel filaments through the application of the Eddy current principle. Permanent magnets are employed to generates a magnetic field with high frequency surrounding a coil of sensor positioned at the filament's output end. The sensor's capacity to detect defects is validated through a meticulous rewinding process, followed by a thorough analysis involving scanning electron microscopy (SEM) and energy-dispersive spectroscopy (EDS). Artificial defects were intentionally introduced into a sample, and their amplitudes were monitored to establish a threshold value. The amplitude signal of these created defect was identified at approximately 10% FSH, which corresponds to a crack depth of about 20 µm. In the experimental production of 182 samples covering 38 km, the defect ratio was notably high, standing at 26.37%. These defects appeared randomly along the length of the samples. The verification results underscore the exceptional precision achieved in the detection of micro surface defects within steel filaments. These defects were primarily characterized by longitudinal scratches and inclusions containing physical tungsten carbide.

Solidification microstructure is formed under high cooling rates and temperature gradients in powder-based additive manufacturing. In this study, a non-equilibrium multi-phase field method (MPFM), which was based on a finite interface dissipation model proposed by Steinbach et. al., coupled with a CALPHAD database was developed for a multicomponent Ni alloy. A qua-si-equilibrium MPFM was also developed for comparison. Two-dimensional equiaxed micro-structural evolution for the Ni (Bal.)–Al–Co–Cr–Mo–Ta–Ti–W–C alloy was performed at various cooling rates. The temperature–γ fraction profiles obtained under 10^5 K/s using non- and qua-si-equilibrium MPFMs were in good agreement with each other. Over 10^6 K/s, the differences between non- and quasi-equilibrium methods grew as the cooling rate increased. The non-equilibrium solidification was strengthened over a cooling rate of 10^6 K/s. Colum-nar-solidification microstructural evolution was performed under cooling rates from 5×10^5 K/s to 1×10^7 K/s at various temperature gradient values under the constant interface velocity (0.1 m/s). The results showed that as the cooling rate increased, the cell space decreased in both methods, and the non-equilibrium MPFM agreed well with experimental measurements. Our results show that the non-equilibrium MPFM can simulate solidification microstructure in powder bed fusion additive manufacturing.

CYP1B1 loss-of-function (LoF) is the main known genetic alteration present in recessive primary congenital glaucoma (PCG), an infrequent disease characterized by delayed embryonic development of the ocular iridocorneal angle and caused by poorly understood molecular mechanisms. To model CYP1B1 LoF underlying PCG, we developed a cyp1b1 knockout (KO) zebrafish line using CRISPR/Cas9 genome editing. This line carries the c.535_667del frameshift mutation that results in a 72% mRNA reduction with residual mRNA predicted to produce an inactive truncated protein (p.(His179Glyfs*6)). Craniofacial defects and jaw maldevelopment were observed in 23% of somatic mosaic F0 crispant larvae (144 hpf). These early phenotypes were not detected in KO F3 larvae (144 hpf) but 27% of adult fishes (4 months) showed uni or bilateral craniofacial alterations, indicating the existence of incomplete penetrance and variable expressivity. These phenotypes increased to 86% in the adult offspring of inbred progenitors with craniofacial defects. No glaucoma-related phenotypes were observed in the cyp1b1 mutants. Transcriptomic analyses of the offspring (7dpf) of KO cyp1b1 progenitors with adult-onset craniofacial defects revealed that differentially expressed genes were functionally enriched in groups related with extracellular matrix and cell adhesion, cell growth and proliferation, lipid metabolism (retinoids, steroids, and fatty acids, and oxidation-reduction processes which included several cytochrome P450 genes) and inflammation. In summary, this study shows the complexity of phenotypes and molecular pathways associated with cyp1b1 LoF, with species-dependency, and provides evidence for dysregulation of extracellular matrix gene expression as one of the mechanisms underlaying pathogenicity associated with cyp1b1 disruption.

Abstract: A biomaterial is proposed for closing extensive bone defects in the maxillofacial region. The composition of the biomaterial includes high-molecular chitosan, chondroitin sulfate, hyaluronate, heparin, alginate and inorganic nanostructured hydroxyapatite. The purpose of the study is to demonstrate morphological and histological early signs of reconstruction of a bone cavity of critical size. The studies were carried out on 84 white female rats weighing 200-250 g. The study group consisted of 84 subjects in total, 40 in the experimental group and 44 in the control group. In all animals, three-walled bone defects measuring 0.5 x 04 x 05 cm were applied subperiosteally in the region of the angle of the lower jaw and filled in experimental group using lyophilized gel mass of chitosan-alginate-hydroxyapatite (CH-SA-HA). In control animals, the bone cavities were filled with an auto-blood clot after bone trepanation and bleeding. The observation periods are 3.5.7 days, 2.3.4.6.8 and 10 weeks. The control of bone regeneration was carried out using multiple morphological and histological analyses. Results showed that following implantation the chitosan construct actively replaced early-stage defects with the formation of a full-fledged new bone tissue as compared to the control group. Already, by the 7th day morphological analysis showed that formation of spongy bone tissue could be seen. After 2 weeks there was a pronounced increase in bone volume (P<0.01), and at 6 weeks after surgical intervention the closure of the defect was 70-80%, after 8 weeks - 100% without violation of bone morphology with a high degree of mineralization. Thus, the use of modified chitosan after filling eliminates bone defects of a critical size in the maxillofacial region, reveals early signs of bone regeneration, and serves as a promising material in reconstructive dentistry.

Influenza virus can cause several complications during pregnancy. Therefore, we aimed to inves-tigate the effects of influenza on the development of congenital abnormalities (CAs) by analyzing the database of the Hungarian Case-Control Surveillance of Congenital Abnormalities (HCCS-CA). In our multicenter, case-control, population-based study, we processed clinician-reported outcomes and diagnoses collected in the HCCSCA. The case group included newborns with dif-ferent non-chromosomal birth defects, while controls were newborns without CAs. Maternal in-fluenza, as a risk factor for CAs, was analyzed by using a logistic regression model and odds ra-tios with 95% confidence intervals (CIs). Our results showed that maternal influenza in the first trimester was associated with increased odds of developing non-chromosomal CAs (OR: 1.41, CI: 1.28–1.55). There were increased odds of neural tube defects (OR: 2.22, CI: 1.78–2.76), orofacial clefts (OR: 2.28, CI: 1.87–2.78) and congenital heart defects (OR: 1.28, CI: 1.10–1.49) after influenza infection. In all cases, we found a protective effect of folic acid supplementation in the first tri-mester. The odds of non-chromosomal birth defects are higher after maternal influenza in the first -trimester. Folic acid or pregnancy vitamin supplementation and antipyretic therapy may reduce the effect of maternal influenza during the first trimester.

Periodontal diseases significantly impact about half of the global population, and their treatment often encompasses relieving symptoms as well as regenerating the destroyed tissues. Revolu-tionary research in the management of periodontal disease includes biomaterials, a boon to re-generative dentistry owing to their excellent biological properties, non-toxic, an-ti-inflammatory, biocompatible, biodegradable, and adhesion. This study aimed to fabricate an injectable fucoidan containing chitosan hydrogel and prove its effectiveness in periodontal bone regeneration. The injectable hydrogel was prepared using the sol-gel method and loaded into 2ml syringes. 40 periodontitis patients with bony defects were recruited and randomized into two groups, to re-ceive fucoidan-chitosan hydrogel and concentrated growth factor, respectively. Customized acrylic stents were used to guide the hydrogel placement into the defect site. Post-surgical changes in clinical parameters were assessed at 3, 6 and 9 months to appreciate the soft & hard tissue changes using repeated measures analysis of variance and Bonferroni’s posthoc test. Significance was kept at 5%. The fucoidan-chitosan hydrogel exhibited significantly lower probing depth values and a higher mean reduction in clinical attachment level as compared to the CGF group at the end of 3 and 6 months (p<0.05). The mean defect fills in the fucoidan-chitosan group was 1.20 at the end of 9 months (p<0.001). The presence of fucoidan in the hydrogel significantly contributed to bone re-generation in humans, thus strengthening its potential in tissue engi-neering. Fucoidan- Chitosan will be a promising biomaterial for bone tissue regeneration.

Point defect-based single-photon emitters (SPEs) in GaN have aroused a great deal of interest due to their room-temperature operation, narrow line width and high emission rate. The room-temperature SPEs at the telecommunication bands have also been realized recently by localized defects in GaN in experiments, which are highly desired for the practical applications of SPEs in quantum communication with fiber compatibility. However, the origin and underlying mechanism of the SPEs remain unclear to date. Herein, our first-principle calculations predict and identify an intrinsic point defect NGa in GaN that owns a zero-phonon line (ZPL) at telecommunication windows. By tuning the triaxial compressive strain of the crystal structure, the ZPL of NGa can be modulated from 0.849 eV to 0.984 eV, covering the fiber telecommunication windows from the O band to the E band. Besides the ZPL, the formation energy, band structure, transition process and lifetime of the SPEs under different strains are investigated systematically. Our work gives insight into the emission mechanism of the defect SPEs in GaN and also provides effective guidance for achieving wavelength-tunable SPEs working in fiber telecommunication windows.

A multiscale modelling approach was developed in order to estimate the effect of defects on the strength of unidirectional carbon fiber composites. The work encompasses a micromechanics approach, where the known reinforcement and matrix properties are experimentally verified and a 3D finite element model is meshed directly from micrographs. Boundary conditions for loading the micromechanical model are derived from macroscale finite element simulations of the component in question. Using a microscale model based on the actual microstructure, material parameters and load case allows realistic estimation of the effect of a defect. The modelling approach was tested with a unidirectional carbon fiber composite beam, from which the micromechanical model was created and experimentally validated. The effect of porosity was simulated using a resin-rich area in the microstructure and the results were compared to experimental work on samples containing pores.

Crystalline phase engineering is a prominent strategy for synergistically optimizing the sur-face-body phases of a catalyst. In this work, TiO2 nanosheets assembled into nanotubes (TNSTs) with two-phases of anatase and rutile were firstly synthesized via crystal engineering by simple thermal annealing, and subsequently loaded with Ru nanoparticles to create efficient benzene hydrogenation catalyst Ru/TNSTs. The well- designed nanosheet-tubes structure boasts large specific surface area and excellent transmission channels, which effectively prevents the ag-glomeration and deactivation of loaded Ru nanoparticles, as well as promotes the internal diffu-sion in the reaction process of benzene hydrogenation to cyclohexene. Furthermore, titanium dioxide nanosheet-tubes contain numerous Ti3+ defects, which not only improves the overall generation rate of cyclohexene, but also enhances the suppression of cyclohexene adsorption. Most importantly, the two-phases of titanium dioxide increases the ratio of the electron defi-ciencies of Ru and promotes cyclohexene desorption. These synergistic properties enhance the selectivity and efficiency of the Ru/TNSTs catalysts, resulting in excellent performance in the hydrogenation of benzene to cyclohexene. Especially the Ru/TNSTs-4 catalyst achieves a 95% in-itial selectivity and 51% yield of cyclohexene in the reaction, outperforming most supported Ru-based catalysts. This work may provide new perspectives for designing efficient benzene hydrogenation catalysts via crystalline phase engineering.

In this paper, the effect of multi-pass friction stir processing on the mechanical properties of AZ91 alloy has been studied. For the numerical investigation, this process has been simulated with the three-dimensional numerical modeling based on the ABAQUS/Explicit. This simulation involves the Johnson-Cook models for defining the material behavior during this intense plastic deformation and investigating the fracture criterion. The tool plunging and stirring phases in the two-pass process has been simulated. To prevent too much distortion of elements during modeling, the Arbitrary Lagrangian-Eulerian technique for automatically re-meshing of distorted elements has been used. The model was calibrated using the experimental results from the previous works. This model can predict the transient temperature distribution and residual stress field during FSP on AZ91. The results show that the maximum temperature in the advancing-side region is more than that in the retreating-side region. In addition, numerical results show that at the end position of the process, the tool during the lift-up leaves the keyhole region in the compressive stress state. The experimental results investigated the effect of multi-pass FSP on the microstructure, microhardness, tensile and creep properties of AZ91 magnesium alloy. The FSP is performed by applying 50% overlapping. The tensile, and creep tests are conducted at several temperatures from 25 to 210 °C. The optical microscopy and scanning electron micrograph (SEM) were used to study the microstructure of the samples after performing multi-pass friction stir processing. The experimental results indicate that on average, the tensile strength, microhardness, and creep strength of the processed samples increased by about 29, 23, and 38 %, respectively compared to the unprocessed ones.

Nowadays, we can observe a worldwide trend towards the development of synthetic biomaterials. Numerous researches have been carried out in order to better understand the cellular behavior involved in the inflammation and bone healing processes related to living tissues. The aim of this study is to evaluate the tissue behavior of two different types of biomaterials: synthetic nano-hydroxyapatite / beta-tricalcium phosphate and hydroxyapatite in non-critical bone defects in rat calvaria. Twenty four rats underwent surgery in which two 3 mm defects in each cavity were performed. The rats were divided into 2 groups: Group 1, using xenogen hydroxyapatite (Bio oss ™); Group 2, using synthetic nano-hydroxyapatite / beta-tricalcium phosphate (Blue Bone ™). Sixty days after the surgery, the calvaria bone defect was filled with biomaterial, the animals were sacrificed and marked with Masson's trichrome and PAS staining, and immunohistochemistry (TNF-α, MMP-9) and electron microscopy analyzes were performed. Histomorphometric analysis indicates a greater presence in the protein matrix in Group 2, in addition to higher levels of TNF-α, MMP-9. The ultrastructural analysis shows an association of material with fibroblasts in the tissue regeneration stage. Paired statistical data indicates that Blue Bone ™ can improve bone formation / remodeling when compared to biomaterials of xenogenous origin.

Most common classifications for acetabular bone defects are based on radiographic two-dimension imaging, with low reliability and reproducibility. With the rise of modern processing techniques based on 3D modelling, methodologies for volumetric quantification of acetabular bone loss are available. Our study aims to describe a new methodology for quantitative assess-ment of acetabular defects, based on 3D modelling, focused on the surface analysis of the integrity of the main anatomical structures of the acetabulum represented by four corresponding sectors (posterior, superior, anterior, and medial). The defect entity is measured as the Area Increase Ra-tio (AIR) detected in all the sectors analyzed on three planes of view (frontal, sagittal and axial) compared to healthy hemipelvises. The analysis was performed on 3D-models from the CT-scan of six exemplary specimens with a unilateral pathological hemipelvis. AIR between the native and the pathological hemipelvis was calculated for each sector, for a total of 48 analysis (range, +0.93% - +171.35%). AIR of >50% were found in 22/48(45.8%) sectors and affected mostly the posterior, medial and superior sectors (20/22, 90.9%). Qualitative analysis showed consistency of the data with the morphological features of the defects. Further studies with larger samples are needed to validate the methodology and potentially develop a new classification scheme.