The article presents the results of research work devoted to the study of composite materials on polymer binder with the content of modified mineral filler - water-dispersion paint and varnish materials on acrylic polymer with modified filler - diatomite. The aim of the study is to obtain polymer-based composites with modified diatomite (water-dispersion paint on acrylic binder) with improved performance properties. Methods: determination of porosity, adhesion, elasticity, hiding power of the control composition; determination of porosity, adhesion, elasticity, hiding power of the obtained composites with the use of modified filler; investigation of the influence of radiation in the infrared radiation (IR) region of the spectrum of the paint coating surface using FLIRB620 thermal imager. As a result of work it is noticed that modification of water dispersions by silica activated diatomite promotes elimination of the main disadvantages of materials and coatings on the basis of acrylate binder - low water resistance and low physical and mechanical characteristics, introduction of modified diatomite into water emulsion paint on acrylate basis does not lead to deterioration of the main operational characteristics of paint and varnish coatings - porosity, adhesion, elasticity and covering. When analyzing the effect of emissivity in the IR region of the spectrum of the paint coating surface, a significant effect of the quantitative content of modified diatomite on the reduction of emissivity of paint coatings in the IR region of the spectrum was established and it was shown that a significant effect of the reduction of emissivity of paint coatings in the IR region of the spectrum is provided by the introduction of modified diatomite in the amount of 40 wt.h. into the mixture. The influence of the time of full-scale tests in the investigated small range regardless of the quantitative composition of modified diatomite on the performance characteristics of the paintwork was established.

The article presents the results of research work devoted to improving the characteristics of paint and varnish coatings based on aqueous dispersions of polyacrylates, it is proposed to modify them by introducing mineral raw materials as fillers and hydrated lime with subsequent processing in a vortex layer apparatus. Introduction of activated diatomite does not cause deterioration of covering power, adhesion and increase of porosity of the paint material. Modification of coatings contributes to the increase of their operational properties, which can be associated with the reduction of free volume in the composite, formation of polymer boundary layers with modified physical and chemical properties. The aim of the study is to obtain water-dispersion paint and varnish composition containing modified diatomite on polyacrylate basis and subsequent study of the main physical and mechanical parameters. The work has been carried out by the following method: determination of porosity, adhesion, elasticity, covering power of the control composition; determination of porosity, adhesion, elasticity, and covering power of the obtained composites using modified filler; investigation of the influence of radiation in the infrared spectrum of the paint coating surface using FLIRB620 thermal imager. As a result of research works it was noticed that modification of water dispersions with silica activated diatomite helps to eliminate the main disadvantages of materials and coatings based on acrylate binder - low water resistance and low physical and mechanical characteristics, introduction of modified diatomite into water emulsion paint on acrylate base does not lead to deterioration of the main performance characteristics of paint coatings - porosity, adhesion, elasticity and covering.

The presented work offers a novel process scheme for valorizing historical Pb-Zn slag, which involves crushing, grinding, and then using separation techniques to concentrate valuable components (nonferrous metals). This methodology could have a significant impact on the global beneficiation of metallurgical slags since, in theory, it is significantly more simple, environmentally friendly, and cost-effective than standard pyrometallurgical or hydrometallurgical procedures. According to previous physicochemical and mineralogical studies, Pb-Zn slag from "Topilnica" Veles is a valuable secondary raw material. This inhomogeneous technogenic resource contains substantial amounts of nonferrous metals (Pb, Zn, Cu, and Ag). However, laboratory tests have indicated that the Pb-Zn slag contains a very uneven valuable metals amounts, ranging from several g/ton to several tens of g/ton. The main issue is that traditional metallurgical procedures for releasing beneficial elements are not commercially viable since the valuable elements are "trapped" within amorphous aluminosilicates or intergrowths of alloy grains and glassy phases. Gravity concentration (Wilfley 13 shaking table) and magnetic separation (Davis separator and disk separator) were used to obtain the final concentrate following comminution and grindability testing. The gravity concentration proved more effective. This streamlined approach of valorizing Pb-Zn slag can reduce the need for hazardous chemicals used in hydrometallurgical refinement operations, as well as the extremely high temperatures required for pyrometallurgical processing. This is the first investigation into the feasibility of this novel approach, which includes direct investigations of the Pb-Zn slag feed using these alternative technologies. After extracting the valuable metals, the amorphous aluminosilicate part of the Pb-Zn slag can be reapplied as an alternative raw material in the building sector, adding to the circularity of the suggested approach..

This study explores novel techniques to improve the detection accuracy of skarn iron deposits using advanced image processing methodologies. Leveraging the capabilities of Aster image, Band Ratio (BR) images, and Principal Component Analysis (PCA), alongside the power of 3D Convolutional Neural Networks (3D-CNN), the research aims to enhance the precision and efficiency of ore detection in complex geological environments. The proposed method employs a specific 3D-CNN architecture, accepting input as a 7×7×C image patch, where C represents the combined number of selected Aster image bands, Principal Component (PC) bands, and computed BR images. To evaluate the accuracy of the proposed method, five distinct image bands combinations, including the proposed bands combination, were tested and evaluated based on the overall accuracy (OA), average accuracy (AA), and kappa coefficient. The results demonstrated that while the incorporation of BR images alongside Aster bands initially seemed promising, it introduced significant confusion in certain classifications, leading to unexpected mis-classification rates. Surprisingly, utilizing solely Aster bands as input parameters yielded higher accuracy rates (OA= 93.13%, AA = 91.96%, Kappa = 90.91%) compared to scenarios involving the integration with band ratios (OA = 87.02%, AA = 79.15, and Kappa = 82.60%) or the integration of BR images to PC bands (OA= 87.78%, AA = 82.39%, Kappa = 83.81%). However, the amalgamation of Aster bands with selected PC bands showed slight improvements in accuracy (OA= 94.65%, AA = 92.93%, Kappa = 93.45%), although challenges in accurately classifying certain features persisted. Ultimately, the proposed combination of Aster bands, PC bands, and BR images (proposed bands combination) presented the most visually appealing and statistically accurate results (OA = 96.95%, AA= 94.87%, and Kappa = 95.93%), effectively addressing misclassifications observed in the other combinations. These findings underscore the synergistic contributions of each of the Aster bands, PC bands, and BR images, with Aster bands proving pivotal for optimal skarn classification, PC bands enhancing intrusions classification accuracy, and BR images strengthening wall rock classification accuracy. In conclusion, the proposed combination of input image bands emerges as a robust and comprehensive methodology, demonstrating unparalleled accuracy in the remote sensing detection of skarn iron minerals.

The purpose of this paper is to analyze market reflexivity in agricultural futures contracts with different maturities. To this end, we apply a four-dimensional Hawkes model to storable and non-storable agricultural commodities. We find market reflexivity for both storable and non-storable commodities. Reflexivity accounts for about 50 to 70 percent of the total trading activity. Differences between nearby and deferred contracts are less pronounced for non-storable than for storable commodities. We conclude that the co-existence of exogenous and endogenous price dynamics does not change qualitative characteristics of the price discovery process that have been observed earlier without consideration of market reflexivity.

The article considers the role of transcrustal magma- and fluid-conducting faults in the formation of mineral deposits, shows the importance of a deep source of heat and hydrothermal solutions in the genesis and history of the formation of these deposits. As a result of the impact on the lithosphere of mantle jets rising along transcrustal faults, intense block-and-clump deformations and tectonic movements are generated; rift systems and volcanic-plutonic belts spatially combined with them are formed; intrusive bodies are introduced. At ore deposits, these processes cause epithermal ore formation as a consequence of the impact of mantle jets rising along transcrustal faults on the lithosphere. At hydrocarbon fields, they play an extremely important role in conduction and convective heat and mass transfer to the area of hydrocarbon generation, determine the relationship between the processes of lithogenesis and tectogenesis, and activate the generation of hydrocarbons from oil and gas mother formations. Detection of transcrustal magma- and fluid-supporting faults was carried out by MMZ and MTZ in combination with other geological and geophysical data. Practical examples are given for mineral deposits under which subvertical transcrustal columns of increased permeability traced to considerable depths have been found. The nature of these unique structures is related to faults of pre-Paleozoic time of emplacement, which determined the fragmentation of the subcrystalline structure of the Earth and later developed inherited in the conditions of development of volumetric fluid dynamics. The residual forms of functioning of fluid-conducting thermohydrocolumns are granitoid batholiths and other magmatic bodies. Experimental modelling of deep processes allowed to reveal the quantum character of interactions of crystal structures of minerals with "inert" gases under elevated T-P conditions. The role of helium, nitrogen and hydrogen in changing the physical properties of rocks in connection with their intrastructural diffusion has been clarified. As a result of low-energy impact, stress fields are formed in the solid rock skeleton, the structure and texture of rocks are rearranged, and general porosity develops. With increasing pressure, energy interactions intensify, deformations, phase transitions and chemical bonds occur in an unstable geological environment, which increases with increasing gas saturation, pressure, and temperature. The process of heat and mass transfer along transcrustal magma- and fluid-supplying faults to the Earth's surface occurs in stages with energy release, which can manifest itself in the form of explosions on the day surface, in coal and ore mines, in earthquakes and volcanic eruptions.

This review stresses the need for geoscience and mining engineering students to be educated during their undergraduate studies in social and sustainability issues so they would have the skills and knowledge in their work after graduation, as professionals, to engage Indigenous People for mutual benefit. Large - scale mining development often takes place on Indigenous land and these educated mining professionals in their contact with these vulnerable communities must act in a responsible way. This includes the important mining policy issues and standards of corporate social responsibility (CSR), social license to operate and free, prior and informed consent from the Indigenous People before mining. For example, these policy standards issues would have been important to consider in Indonesia where the Indigenous Muluy Dayak community in East Kalimantan tried to resist large-scale mining operations by depicting their small-scale mining as part of their Indigenous customs and identity and in Australia where there was the recent destruction of an Aboriginal sacred site during large scale mining operations.

The article presents the results of studies aimed to identify the effect of foliar treatments of winter wheat, sugar beets and soybeans with mineral and bioorganic fertilizers. Their positive effect on increasing the concentration of mineral forms of nitrogen in soil was revealed. The crop types have a greater influence on the size of nitrous oxide emissions: in winter wheat crops - 679 µg/m3, soybeans - 637.2 µg/m3, sugar beets - 576.8 µg/m3. The amounts of nitrous oxide emissions were lower in the variants without the use of phosphorus-potassium fertilizers. The Ruter AA fertilizer showed the greatest efficiency on winter wheat crops - 42.7 c/ha. Soybean grain yield of 44.2 c/ha was also achieved by using Ruter AA, as well as Geo-humate together with phosphorus-potassium fertilizers. On the background of the actual supply of phosphorus and potassium, maximum yield was obtained when using N30 on the leaf - 39.3 c/ha. Foliar feeding ensured a yield of sugar beet root crops of up to 67.1-77.4 c/ha on the backdrop of the application of phosphorus-potassium fertilizers with the advantage of using Amino turbo. The largest yield of sugar beet roots without use of mineral phosphorus and potassium was ensured by N30 treatment of the leaf in the phases of 4-6 and 8 leaves - 63.2 t/ha. Of the organo-mineral fertilizers and biostimulants, the best result was shown by the use of Ruter A - 62.6 t/ha. We believe that foliar feeding of crops can be a sustainable farming method that can increase crop yields and reduce N2O emissions.

: This study was aimed at assessing adaptation and bonding of discontinuous (short) glass fiber-reinforced composite to intraradicular dentin EverX Flow (GC Corporation, Tokyo, Japan), when used as intracanal composite filling and anchorage instead of traditional fiber posts. (2) Methods: Seventy intact extracted human teeth were endodontically treated and randomly divided into 6 groups (n=10), depending on the materials used in the post space. In Group 1, a 2-bottle universal adhesive G2 Bond Universal + EverX Flow were tested. In group 2, a single-component universal adhesive G-Premio Bond + EverX Flow were used. In groups 3 and 4 the same materials are tested, but after cleaning of the canal walls with 17% EDTA and final irrigation with 5.25% NaOCl Ultrasound Activated. In the last three Groups (5-7) traditional prefabricated GC Fiber Posts 1.6 mm silanized with G-Multi Primer for 1 minute are cemented with a dual-cured composite resin cement (GradiaCore), after ultrasonic irrigation in the groups 6 and 7. In each group, 1 mm-thick slices from each sample (n=10) were cut for light microscope and SEM inspection for study materials adaption to the dentin and for measuring push-out strength of post / cemement material to the dentin / prefabricated post. These results were statistically analyzed: as the data distribution was not normal, the Kruskal-Wallis Analysis of Variance by Ranks had to be applied. The level of significance was set at p<0.05. Results: Push-out forces varied between 6.66-8.37 MPa. No statistically significant differences were recorded among the groups. Microscopic examination showed that ultrasonic irri-gation increased adaptation of the materials to the dentin surface. There was a trend of higher bond strength among the tested groups when EverX Flow was used. Also, the type of failure was more often cohesive when ultrasonic irrigation and two-step adhesive system were used. Conclusions: Within the limitations of this in vitro study, it may be concluded that when EverX Flow was used for intracanal anchorage in the post-endodontic recon-struction, similar push-out retentive forces and strength to those of traditional fiber posts cemented with particulate filler resin composite cements were achieved. Although further studies are necessary, EverX Flow represents an effective alternative to traditional fiber post adhesion in particular when used in combination with the two-step adhesive system and ultrasonic activation.

Dementia, primarily caused by neurodegenerative diseases like Alzheimer’s disease (AD), affects millions worldwide, making detection and monitoring crucial. To enable these tasks, we propose encoding in-text pauses and filler words (i.e., “uh” and “um”) in text-based language models, and thoroughly evaluate their effect in performance. Additionally, we suggest using contrastive learning to improve performance in a multi-task framework. Our results demonstrated the effectiveness of our approaches in enhancing the model’s performance, achieving 87% accuracy and an 86% F1-score. Compared to the state-of-the-art, our approach has similar performance despite having significantly fewer parameters. This highlights the importance of pause and filler word encoding on the detection of dementia.

The article focuses on mining of non-energy mineral resources with minimum environmental impacts. It issues from research results of a project Competence Centre for Effective and Ecological Mining of Mineral Resources implemented at the Faculty of Mining and Geology at VŠB-Technical University of Ostrava, Czech Geological Survey, a company Watrad ltd., a state enterprise Diamo, a company RPS Ostrava plc and a company Sedlecký kaolin plc. The paper starts with a partial analysis of the existing legal norms related to mining and processing of mineral resources. Next, it analyses mineral resource mining options free of negative environmental impacts. The fundamental tool to assess potential environmental impacts of mining is the implementation of Environmental Impact Assessment (EIA) process for a given mineral resource. In the Czech Republic environmental impact assessment is carried out by course of Act 100/2001 Coll. Its important amendment is Act 39/2015 Coll. claiming, inter alia, that the environmental impact assessment is rigidly connected with other permits and procedures, such as the zoning process and building construction permits. The article describes the environmental impacts of mining of non-energy mineral resources, including the following factors: appropriation of land, impacts on surface water, ground water and soil, noise, influence on the landscape character, and air pollution. The paper also includes a case study summarizing information on the environmental factors that may play a role in potential underground mining of graphite in the deposit Český Krumlov - Městský Vrch and the deposit Lazec - Křenov.

The properties of rubber are strongly influenced by the distribution of filler within the polymer matrix. Here we introduce a Monte Carlo-based morphology generator. The basic elements of our model are cubic cells, which, in the current version, can be either silica filler particles or rubber volume elements in adjustable proportion. The model allows the assignment of surface free energies to the particles according to whether a surface represents, for instance, 'naked' silica or silanised silica. The amount of silanisation is variable. We use a nearest-neighbour site-exchange Monte Carlo algorithm to generate filler morphologies, mimicking flocculation. Transmission electron micrographs (TEM) as well as small angle scattering (SAS) intensities can be calculated along the Monte Carlo trajectory. In this work we demonstrate the application of our morphology generator in terms of selected examples. We illustrate its potential as a tool for screening studies, relating interface tensions between the components to filler network structure as characterized by TEM and SAS.

Composite fiber materials are superior materials due to their high strength and light weight. Composites reflect the properties of their constituents, which is proportional to the volume fraction of each phase. There are different fiber reinforcement types and each affects it’s flexural, tensile and compression strength. When selecting a composite for a specific application, the forces excreted on the composite must be known in order to determine the reinforcement type. Unidirectional fiber reinforcement will allow very strong load resistance but only in one direction where as a random orientated fiber reinforcement can resist less load but can maintain this quota in all directions. These materials are said to be anisotropic. Certain composite fibers, taking into consideration there weights, are physically stronger than conventional metals. This research deals with the analysis of three composite materials with different reinforcement types, volume fraction and phase content. It was found that material A (glass epoxy) was the strongest in the longitudinal direction with a flexural strength of 534 MPa in the longitudinal and 420 MPa in the transverse direction. The flexural stresses of material B (glass silicone) and material C (glass polyester) where both found in the 120 to 135 MPa range. Differences were due to their differences in matrix composition and reinforcement type.

Despite its growing importance as a dry beneficiation method, there is a lack of studies exploring the fundamentals aspects of dry jigging. In this sense, this study focuses on explore some essential aspects of density-based separation in dry jigs, like pulse profile, energy consumption and, especially, stratification over time, also exploring an innovative operational strategy here called “transient pulsation”. The tests were carried out using density tracers distributed across 11 density ranges (0.4-2.4 g/cm³) and employing a base bed (gravel) to analyze their segregation in a pilot-scale dry jig. Pressure drop and active power data were acquired to measure the pulse characteristics and energy consumption. The findings suggest that establishing the dry jigging cycle is more complex than in hydraulic jigs due to the compressibility of air. Stationary pulsation tests revealed an unstable behavior of stratification over time, contrasting with traditional hydraulic jigs, while transient pulsation tests unveiled varied trends in separation quality. Energy consumption analysis underscored the significant role of the blower drive. These insights have the potential to inform operational enhancements in dry jigging.

In this study, the determination of static E50 and υ parameters of rock materials was investigated using P-S wave velocities and Shore hardness (SH), non-destructive measurement methods. We used multiple linear regression (MLR), multiple non-linear regression (MNLR) and artificial neural network (ANN) models to estimate and determine these parameters. When the models defined by MLR, MNLR, and ANN were compared to the R2 values, ANN models that estimate E50 and υ parameters of rock materials using non-destructive methods (Vp, Vs, Vp/Vs, d, and SH) could be determined with higher accuracy than MLR and MNLR models. The study’s originality is based on the fact that ores such as galena, chromite, and barite have been studied for the first time on rock mechanics, and in this respect, it offers an innovative perspective. In addition, the use of all non-destructive measurement methods, Vp, Vs, and Shore hardness tests, also increases the originality of the study.

The aim of this work is to compare two softwares (MAUD and TOPAS) based on the Rietveld algorithm and to test the concept of tolerance factor using the dissolution at high temperature of yttrium into BaTiO₃. In general, both softwares give up different values of the crystalline parameters however the trends are similar in most cases but the analysis of the strain and crystallite size in the BaTiO₃ crystals suggests that, in this particular case, MAUD offered results more consistent with the expected behavior. Using the crystalline parameters calculated by Rietveld, the tolerance factor values were obtained and these data suggest even better stability in the crystalline structure than that expected using theoretical parameters. Tolerance factor concept also indicates that Ti⁴⁺ should be preferred.

This work shows the physicochemical and mineralogical characterization of diatomites form the Hidalgo and Jalisco States, Mexico. In the case of the mineral from Hidalgo State, this has the following chemical composition; 70.0 % wt. SiO₂, 11.63 wt. % Al₂O₃, 1.95 wt. % FeO, 1.79 wt. % MgO, 2.41 wt. % K₂O, 0.85 wt. % CaO and 6.10 wt. % Na₂O. On the other hand, the mineral from Jalisco has the following chemical composition; 93.58 wt. % SiO₂, 3.03 wt. % Al₂O₃, 1.81 wt. % FeO, 0.40 wt. % MgO, 0.92 wt. % K₂O, 0.11 wt. % CaO and 0.24 wt. % Na₂O. For recovery of metals, both minerals got arsenic, silver, lead and nickel recoveries upper to 95 % and lower to 10 % for chromium. According to efficiency of interchange, the mineral from Hidalgo is slightly higher in the case of arsenic, lead and silver; while for nickel and particularly chromium (VI) the efficiency is higher for the mineral from Jalisco.

There is increased concern that the quality, generalizability, and reproducibility of biomedical research can be influenced by the sex of animals used. We studied the differences between male and female mice in response to invasive pulmonary mucormycosis including susceptibility to infection, host immune reaction, and responses to antifungal therapy. We used diabetic ketoacidotic (DKA) or neutropenic mice infected with either Rhizopus delemar or Mucor circinelloides. The only difference detected was that when DKA mice were infected with M. circinelloides, female mice were more resistant to infection than male mice (median survival time of 5 vs. 2 days for female and male mice, respectively). However, a 100% lethality was detected among infected animals of both sexes. Treatment with either liposomal amphotericin B (L-AMB) or posaconazole (POSA) protected mice from infection and eliminated the difference seen between infected but untreated female and male mice. Treatment with L-AMB consistently outperformed POSA in prolonging survival and reducing tissue fungal burden of DKA and neutropenic mice infected with R. delemar or M. circinelloides, in both mouse sexes. Although little difference was detected in cytokine levels among both sexes, mucormycosis infection in the DKA mouse model induced more inflammatory cytokines/chemokines involved in neutrophil (CXCL1) and macrophage (CXCL2) recruitment vs. uninfected mice. As expected, this inflammatory response was reduced in the neutropenic mouse model. Our studies show that there are few differences between female and male DKA or neutropenic mice infected with mucormycosis with no effect on the outcome of treatment or host immune response.

Achieving the thermal conductivity required for efficient heat management in semiconductors and other devices requires the integration of thermally conductive ceramic fillers at concentrations of 60 vol% or higher. However, the increased filler content often negatively affects the mechanical properties of the composite matrix, limiting its practical applicability. To address this issue, in this paper, we present a new strategy to reduce the required ceramic filler content: the use of a thermally conductive ceramic composite filler with carbon nanotubes (CNT) grown on aluminum nitride (AlN). We have combined catalyst coating technology with vacuum filtration to ensure that the catalyst is uniformly applied to micrometer-sized AlN particles, followed by efficient and uniform synthesis of CNTs using a water-assisted process in a vertical furnace. By carefully controlling the number of vacuum filtration cycles and the growth time of the CNTs, we demonstrate precise control over the number and length of the CNT layers, thereby adjusting the properties of the composite to the intended specifications. When AlN/CNT hybrid fillers are incorporated into silicone rubber, while maintaining the mechanical properties of rubber, the thermal diffusivity achieved at reduced filler levels exceeds that of composites using AlN-only or simultaneous AlN and CNTs formulations. This demonstrates the critical role of CNTs on AlN surfaces. Our study represents a significant advancement in the design of thermally conductive materials with potential implications for a wide range of applications.

Establishment of protected areas (PAs) is one of the key global conservation strategies that currently cover approximately 15% of the earth’s land surface. Globally, PA networks are designed to curb the growing anthropogenic pressures in areas with high biological diversity. Despite the importance of PAs in conserving the vanishing biodiversity and unique habitats, many of them are in critical condition due to poor governance thus functioning below the expected level. Moreover, in many developing countries, the PA coverage is below the global standard. Recognizing their contemporary role in conservation, governments have recently agreed to expand the global PA coverage to 17% by the year 2020 (Aichi target 11). This book with eight chapters from different regions of the world provides an overview of the PAs governance, institutional mechanisms, conservation benefits, limitations and challenges associated with their respective policy discourse, integrated management, and functional attributes. Protected areas expect to to play an important role in the long rn in conservation and protection of biodiversity and ecosystems particularly in countries where population pressure and habitat loss are high. Regular intervention, political commitment, and effective governance are essential for the sustainability of PAs across the world. Here, we also attempted to shed some light on future development clues for the sustainable management and monitoring of PAs worldwide.

The petrogenesis and geodynamic implications of the early Paleozoic adakitic rocks in the east of Inner Mongolia remain topics of debate. In this study, petrology, zircon U–Pb age and Lu–Hf isotopic composition, whole-rock geochemistry and Sr–Nd isotopes from adakitic rocks. Zircon U–Pb dating results demonstrate that the formation age is 242.8±1.0Ma, 247Ma，which is the product of Early Triassic magmatism. Petrology and geochemical study have shown that the granodiorite have high SiO2 (66.93% ~69.40%), Al2O3(15.37% ~ 15.43%), MgO (1.35% ~1.55%), with LREE enrichment and HREE deficit，and they have high Sr, low Y. and high Sr/Y ratios, showing typical signatures of adakitic rocks. The εHf(t) values of zircon vary between +11.3 and +13.8, with a low whole-rock (87Sr/86Sr)i ( 0.703382 )and positive εNd(t) values, the average Mg# of the rock is 56.14, suggesting that adakite derived from partial melting of MORB, and magma interaction with the mantle. Comprehensive analysis suggests that during the Late Permian to Early Triassic, the subducted slab of the Paleo-Asian Ocean broke off, and the residual oceanic slab preserved in the mantle beneath the subduction zone underwent partial melting, generating adakitic magma.

This study investigates the potential of utilizing hazelnut shells (HS) as an innovative filler in three-layer plywood technology, addressing the growing need for sustainable, high-performance materials. Traditional plywood production relies on adhesives enhanced with various fillers to improve physical, mechanical, and operational characteristics. This research explores using native, chemically modified, and activated carbon derived from hazelnut shells as fillers in urea-formaldehyde (UF) resin. The mechanical properties, water absorption, and formaldehyde emissions of the produced plywood were thoroughly analyzed. Key findings demonstrate that incorporating 10 part by weight (pbw) native hazelnut shell flour significantly enhances the modulus of rupture (MOR) and modulus of elasticity (MOE). Chemically modified hazelnut shell flour achieves optimal results at 5 pbw, while activated carbon from hazelnut shells, even at 1 pbw, markedly improves bonding strength and thermal properties. Notably, activated carbon effectively reduces formaldehyde emissions and improves water resistance, indicating better further dimensional stability and lower environmental impact. The study also shows that excessive filler content negatively affects strength parameters, confirming the importance of optimizing filler concentration. These results highlight the potential of hazelnut shells as an eco-friendly alternative filler in plywood production, contributing to waste valorization and environmental sustainability. This study supports the practical application of hazelnut shell fillers, promoting a circular economy and reducing reliance on traditional, less sustainable materials, thus providing a valuable solution for the wood composite industry.

The escalating demand for multifunctional and advanced materials for growing industries has turned scientific exploration to graphene-based hybrid filler polymer composites. The introduction of graphene with other fillers into polymer matrices results in astonishing properties and thus has gained significant attention in recent years. This study addresses the significance of graphene-based hybrid filler polymer composites in progressive materials science and engineering. The paper encloses some traditional and current preparation techniques employed in the fabrication of composites and a comprehensive review of successfully prepared graphene hybrid polymer composites with enhanced mechanical, thermal, and electrical properties reported in published research. The role of different factors, e.g., filler type, aspect ratios, filler-matrix compatibility, dispersion effects, homogeneity, filler orientation through polymer matrices, and curing conditions, are summarized. Finally, the applications in heavy industries, e.g., aerospace, electronics, energy storage, and automotive sectors were also analyzed. We hope this study will serve as a practical resource for new researchers and practitioners to understand and harness the full potential of these composites in various scientific and industrial fields.

Deep learning has increasingly been employed to identify minerals. However, deep learning can only be used to identify minerals in the distribution of the training set, while any mineral outside the spectrum of the training set is inevitably categorized erroneously within a predetermined class from the training set. To solve this problem, the study introduces the approach that amalgamates One-Class Support Vector Machines (OCSVM) with the ResNet architecture for the out-of-distribution mineral detection. Initially, ResNet undergoes training using a training set comprising well-defined minerals. Subsequently, the earlier layers of the trained ResNet are employed to extract the discriminative features of the mineral under consideration. These extracted mineral features then become the input for OCSVM. When OCSVM discerns the mineral in the training set's distribution, it triggers the subsequent layers within the trained ResNet, facilitating the accurate classification of the mineral into one of the predefined categories encompassing the known minerals. In the event OCSVM identifies the mineral out of the training set's distribution, it is unequivocally categorized as an unclassified or 'unknown' mineral. Empirical results substantiate the method's capability to identify out-of-distribution minerals while concurrently maintaining a commendably high accuracy rate for the classification of the 36 in-distribution minerals.

By repeated unloading and loading of the excavation dynamic and static loads, repeated train dynamic and static loads of multi-factors, the underpass tunnel, cross tunnel engineering influence area rock layer, the existing tunnel structure of the three constitutes a multifaceted structure, multi-factor interaction system. Existing tunnels into the prediction theory model of the new tunnel excavation process of dynamic and static loads, dynamic and static loads of existing tunnels are mostly analyzed individually, the results of synergistic analysis needs to be improved. Based on the theory of the current layer method, the paper comprehensively considers the stiffness of the existing tunnel, the stiffness of the new tunnel, the excavation method load and the existing tunnel load, coupled with Peck's empirical formula, the theoretical model of deformation prediction for excavation of a two-lane highway tunnel under the tunnel through the existing railroad is proposed, and verified and optimized by numerical calculations and monitoring data, which proves the applicability and reliability of the theoretical model in the similar strata and the project promotion.

Sub-national governments (SNGs) in developing countries have increasingly explored green municipal bonds as a financing tool, driven by promises of lower borrowing costs, enhanced reputation, and support for sustainable economic development. This study aims to critically examine these claims by analysing the actual costs and complexities associated with green municipal bonds (GMBs). The research involves a comparative analysis of traditional municipal bonds and GMBs, focusing on the financial and operational challenges faced by SNGs. Detailed case studies from Mexico City and Cape Town are used to illustrate the practical implications of issuing GMBs. The findings reveal that, despite similar or slightly lower interest rates, GMBs often entail higher issuance costs due to the need for certification, monitoring, and reporting of green projects. These additional costs, coupled with the necessity of hiring external consultants, make GMBs more expensive and difficult to replicate after initial transactions. Furthermore, the study highlights that the demand from investors has not met initial expectations. While green-aligned investors show a higher appetite for GMBs, they constitute only a small portion of the finance market. Traditional investors, primarily focused on financial returns, are less inclined to invest in GMBs solely based on their green label. Consequently, many SNGs have reverted to issuing traditional “vanilla” municipal bonds while still using the proceeds to fund green initiatives. This shift underscores the need for a realistic assessment of GMBs’ viability in developing countries and calls for a re-evaluation of strategies for promoting sustainable economic development through green finance.

Open-pit uranium mining in the south Texas Gulf Coast region was active during the second half of the 20th century. Although some mines have extensive records documenting the locations and extents with descriptions of reclamation procedures and timelines, abandoned and reclaimed mines with minimal documentation concurrently exist where little is known about locations, mine waste volumes, and reclamation status. Advanced mapping of these mining operations is helpful for producing basic mine land inventories and assessments of mine waste; identifying potential undeveloped resources and environmental health issues; and for developing proper management, restoration, and reclamation strategies. We studied known reclaimed and unreclaimed mine sites to develop a spatiotemporal mapping approach utilizing multiple techniques in remote sensing as a proof of concept. A mapping classification system was developed to identify uranium mine waste-rock piles, mine pits (with and without waste water), the total area of land disturbance due to mining, and to differentiate abandoned and reclaimed mine features using lidar (Light Detection and Ranging) analysis and multispectral temporal analysis. Visual interpretation of Landsat imagery and time-series analysis revealed the temporal life-cycle of mining, historical areas of disturbance, and reclamation; however, mine features below vegetation canopies are not always visible in satellite imagery. Lidar laser scanning penetrates the vegetation canopy to measure the topographic elevation and exposes anthropogenic modifications to the landscape. Lidar analysis (bare earth elevation surface, slope, topographic contours, topographic textures, and overland-flow hydrography) revealed mine features, and expansive areas of mining disturbance. The spatiotemporal mapping approach proved to be useful for identifying and characterizing known mine features, areas of disturbance, and reclamation status. Historical pre-mining topographic data were available at only 4 of the mines for comparison where the cut-and-fill tool estimated 21% less waste-rock volume, indicating that information about pre-mining terrain topography and/or subsurface mine waste geometry is needed to improve accuracies for quantifying buried mine waste volume at reclaimed mine sites.

Solid waste management in Accra is a major challenge to the Metropolitan Authorities and inhabitants. The rapidly increasing population coupled with poor capacity of the municipal and private waste management companies to management waste effectively has created issues of environmental concern. Due to poor waste managements systems, most household dispose waste indiscriminately leading to floods and health issues. The study showed that about 60% of household waste is organic materials which has the potential to be converted to compost for agriculture purpose. Meanwhile plastics and rubbers which litters the environment as well as blocking major storm drains and gutters hence creating huge environmental hazard is made of 11% of the total component of most household waste generated daily. The study also revealed that among the methods of disposing waste, dumping waste in skip containers located at authorized places was the preferred means of disposing waste by household though others also dispose waste by other means such as burying and burning. Inadequate skip containers per population of household in an area coupled with irregularity of tracks picking these containers makes skip containers dumping site ugly scene, hence creating health issues. Among the constraints that impact negatively on sustainable waste management in Accra Metropolis, economic constraints was perceived as the main challenge which affect efficient waste management. Currently the country is going through serious economic challenges so government does not release money timely to fund projects which waste management is key. Most donor partners that use to support the government with funds have either reduced or redrawn their services as they have no confidence in the state of Ghana economy. Aside the constrains, the study also indicated that factors such as poor public attitude towards waste management, poor enforcement of sanitation by-laws, inadequate and untimely release of government funds were also seen as the main factors affecting waste management.

Cutting and packing problems have been studied for decades and are of concern for a wide variety of industries to reduce costs and material utilization. This paper addresses the one-dimensional cutting stock problem, focusing on minimizing total stock usage. Procedures that address this problem include linear programming methods and metaheuristics. However, linear programming methods are limited to low-complexity instances, while most metaheuristics require extensive parameter tuning. In this paper, we develop a Petri-net model to construct cutting patterns. Using the reachability tree of the Petri net, the filtered beam search algorithm is implemented to find the best solution. Our algorithm is compared with the Least Lost Algorithm and the Generate & Solve algorithm over five datasets of instances. These algorithms share some characteristics with ours and have proven to be effective and efficient. Experimental results demonstrate that our algorithm effectively finds optimal solutions for both low and high-complexity instances. These findings confirm that Petri nets are suitable for modeling and solving the one-dimensional cutting stock problem.

Crop rotation diversification using legumes has been advocated as one of the solutions to improve the resilience of the crop system to various environmental stresses and the use of nitrogen resources. However, when forage legumes or grass-legumes are ploughed, there is a high risk of nitrate leaching, especially in sandy soils. The aim of the study was to determine the effect strip tillage intercropping management on soil mineral nitrogen (SMN), water-extractable organic carbon (WEOC) content and winter wheat (WW, Triticum aestivum L.) grain yield compared to forage legume and WW monocropping with conventional tillage. In intercropping was used winter wheat - black medick (Medicago lupulina L.) WW+BM, winter wheat - white clover (Trifolium repens L.) WW+WC, and winter wheat - Egyptian clover (Trifolium alexandrinum L.) WW+EC. Research was repeated in two experiments. The results showed that after strip tillage and WW sowing less or similar SMN content cud be detected, as in conventional tillage and WW + forage legumes intercropping. WW grain yield in intercrops decreased, compared to the grasses monocultures that were ploughed before WW sowing. The highest amount of WEOC was in intercropping soil growing WW+WC or in all fields (except WW+EC) after applying strip tillage. During the research period, the amounts of mobile humic substances (HSs) and mobile humic acids (HAs) changed analogously. Their content increased substantially in fields with WC and EC, regardless of whether the grasses were ploughed or grown with WW.

Biosolids from stabilized sludge presents a high fertilization potential due to its rich content of nutrients and organic matter. Three formulas of organo-mineral fertilizers based on biosolids were manufactured having at least 2 % N, 2 % P2O5, and 2 % K2O and characterized by classical and advanced methods. The content of N and P in the final formula was measured using specific reactants combined with VIS-nearIR spectroscopy. Additionally, all three formulas were characterized by advanced 1H NMR relaxometry, double-quantum and FT-IR spectroscopy. Structural characterization was performed using SEM, EDX and X-ray diffraction. Four dynamical components were identified in the T2-distribution showing that the rigid component is into a percentage larger than 90 %. In order to evaluate the release properties of organo-mineral fertilizers dynamic measurements of electric conductivity and pH were performed, by placing 0.25 g of formulas (V1, V2 and V3) in 200 ml of distillate water. It was found that V3 present the smallest release velocity, but release the largest amount of fertilizers. Two release mechanisms were also observed.

Aim: The purpose of this study is to evaluate the remineralization potential of primary teeth enamel after being exposed to different laser diode therapy. Methods: Ninety-six vestibular primary teeth enamel samples were divided into eight groups (n=12) with varying treatments: control (G1), CPP-ACP-fluoride varnish (G2), diode lasers at 980 nm (G3), 808 nm (G4), 450 nm (G5), 980 nm + CPP-ACP-fluoride varnish (G6), 808 nm + CPP-ACP-fluoride varnish (G7), and 450 nm + CPP-ACP-fluoride varnish (G8). Each sample was assessed using DIAGNOdent® at baseline, post-treatment, and post-pH cycle re-mineralization. SEM imaging was performed before and after treatment and following the pH cycle. Results: The results indicated that the 980 nm and 808 nm diode lasers, both alone and in combination with CPP-ACP-fluoride varnish, either maintained or increased the calcium (Ca) weight percentage (Wt%) in the enamel. The 980 nm diode laser combined with CPP-ACP-fluoride varnish (G6) showed a significant increase in Ca Wt%, suggesting a strong remineralization effect. Similarly, the 808 nm diode laser alone (G4) also promoted a substantial increase in Ca Wt%. In contrast, the 450 nm diode laser, whether applied alone or in combination with CPP-ACP-fluoride varnish, resulted in a lower Ca Wt% and an increase in phosphorus (P) Wt%. Most groups, except for the CPP-ACP-fluoride varnish alone (G2), demonstrated an increase in P Wt%, indicating a complex interaction between laser therapy and enamel remineralization. Conclusions: The combined use of laser therapy with CPP-ACP-fluoride varnish significantly enhanced the remineralization of temporary teeth enamel. The 980 nm diode laser + CPP-ACP-fluoride varnish showed the most pronounced improvement in remineralization, while the 808 nm diode laser alone also effectively increased calcium solubility. These findings suggest that higher wavelength diode lasers, particularly when combined with remineralizing agents, can effectively enhance the mineral content of primary teeth and promote enamel remineralization.

Good governance in natural resource management (NRM) is one of the most challenging issues in developing countries that often inappropriately embedded in national policies and political agendas. It is, in fact, even more important for countries like Bangladesh with exceptionally high pressure and dependence on its natural resources for sustaining rural livelihoods. Globally, nowadays, good governance is considered as one of the key factor for achieving the goal of sustainable development and biodiversity conservation. Bangladesh, of late has responded to that global zeal by involving local communities in the management of country’s declining forest and other natural resources. The colonial legacy of the forestry sector of Bangladesh was planned and, managed as interim projects through donors’ prescriptions. Thus, institutions, management processes and conservation outcomes were problematic. The conventional approach adopted by colonial and post-colonial regimes for forest management also proved to be inefficient due to its top-down management system. The absolute dependency on donor support, and their prescription sometimes worsened the situation both ecologically and socially. Global, regional and local trends supported the need for a different dimension in the governance paradigms. The introduction of a pluralistic approach, known as co-management in protected areas (PAs) is an example of an attempt whereby shared governance mechanism are implemented to attain the desired goals of conservation that will also address the livelihoods and aspirations of communities living in and around PAs of the country. However, in designing future forest and PA regimes the concern of the external aid support and attached conditions remain a reality that needs to be addressed. Adequate attention should be given to our vanishing biodiversity, culture and community livelihoods through devising an appropriate governance mechanism recognizing and supporting local rights, access and participation in the environmental management. It is now time to mainstream the adhoc nature of governance according to our national conservation strategy and policy frameworks in order to achieve the goals and objectives of the Bangladesh NRM sector addressing the human and community right of people in the specific context of forest protected areas management.

The growing global population and limitations in fish catch production have led to a surge in the demand for aquaculture. Contaminants of emerging concern (CEC) are frequently being detected at low levels in surface water. These CECs, which include previously unidentified or unregulated pollutants, pose potential risks to health and the environment, though their impacts are not yet fully understood. Extensive research studies have been proposed and undertaken to address the issue of aquaculture wastewater, aiming to minimize its impact and implement effective treatment methods. This review provides an analysis of various technologies used for treating aquaculture wastewater using advanced oxidation processes (AOPs) focusing on photocatalysis and ozonation. It examines their advantages and disadvantages, as well as their respective treatment efficacies and discusses their potential applications in sustainable aquaculture practices complying with the Sustainable Development Goals of 1,2 and 6 and the Environmental Social and Governance (ESG) framework.

Biodiversity has become an issue of global anxiety over the past decades due to its rapid decline worldwide. Bangladesh as one of the most densely populated countries in the world is no more exception. The country, although, was once very rich in biodiversity, during the last few decades as a consequence of the rapid reduction in forest area, urbanisation, habitat modification, unsustainable natural resources use and collection and overall climate change it has decreased alarmingly. Of late, the government, as a signatory of various regional and international conservation treaties, has taken various initiatives to improve country’s dwindling biodiversity. This paper reviews the present situation of biodiversity in Bangladesh, management trends and major causes of biodiversity loss. A separate statutory body is fundamental to ensure conservation, sustainable use and equitable sharing of benefits arisen from biodiversity in the country.

Despite of being an exceptionally biodiversity rich country, the forest coverage of Bangladesh is declining at an alarming rate. Declaration and management of protected areas in this regard is one of the efforts from government side to tackle the loss of biodiversity. The limited numbers of forest-protected areas (FPA), established to conserve the dwindling forest biodiversity of the country with high pressure on them for timber, non-timber forest products, and fuelwood - makes their management challenging. Moreover, most of the FPAs of the country declared only in the recent decades with very limited infrastructure, manpower and policy support for monitoring and governance. Some people-centred approaches for the management of FPAs and alternative livelihood and income generation subsidies although made available through a few project interventions, their number are still inadequate and performance remains less than satisfactory. This chapter provides a critical review of the FPAs of Bangladesh looking at their role in biodiversity conservation, management challenges, and key lessons from previous management interventions with recommendations for the future. It has been revealed that the FPA system of Bangladesh still poorly represents the diverse forest ecosystems with relatively small forest size and lack of corridors for the movement of wildlife. There are ample opportunities to render co-management of FPAs an effective strategy to minimize the conflicts in FPAs management in the country. It is, however, important to ensure the access of local forest-dependent people to different alternative income generating options that may adequately support their livelihoods.

Environmental nanoparticles have been shown to exist in most aquatic environments, and environmental nanoparticles in water distribution systems significantly affect water quality. However, little research has been conducted on the environmental nanoparticles in mineral water, which is a special water resource. Nanoparticle tracking analysis (NTA) and high-resolution transmission electron microscopy (HRTEM) were conducted. This study was the first to identify many environmental nanoparticles in natural mineral water in Zibo City, Shandong Province, China. The results of the NTA showed that the concentration of the particles was 5.5 ×106 particles/mL and the peak diameter of the size distribution was 180 nm. The HRTEM showed that the nanoparticles were granular, pinniform, rodlike, and flakey in shape, and some of the nanoparticles existed in aggregation. The energy-dispersive spectrometry results showed that most of the nanoparticles contained O, Mg, Ca, Si, Fe, Ti, and P, and some of them also contained F, V, S, and Mn. When combined with the characteristics of the selected area electron diffraction pattern, the nanoparticles were confirmed to be Ca-bearing nanoparticles, attapulgite nanorods, MnO2 nanosheets, and TiO2 nanoparticles. These results indicate a new form of elements occurring in mineral water. In addition, based on the chemical and physical characteristics of the nanoparticles and mineral water, these environmental nanoparticles in the mineral water are likely to be the weathering byproducts of minerals. These nanoparticles within mineral water provide a good opportunity for understanding the behavior of nanoparticles in varied systems. Moreover, environmental nanoparticle science is important for continuing efforts in water safety, treatment, and remediation.

Clathrate hydrate-based technologies have been considered as promising and sustainable alternatives for the effective management of the climate change risks related to emissions of carbon dioxide, produced by human activities. This work presents a combined experimental and computational investigation of the effects of the operational procedures and characteristics of the experimental configuration, on the phase diagrams of CO2-H2O systems and CO2 hydrates formation, growth and dissociation conditions. The operational modes involved (i) the incremental (step-wise) temperature cycling and (ii) the continuous temperature cycling processes, in the framework of an isochoric pressure search method. Also, two different high pressure PVT configurations were used, of which one encompassed a stirred tank reactor and the other incorporated an autoclave of constant volume with magnetic agitation. The experimental results implied a dependence of the subcooling, (P, T) conditions for hydrate formation and dissociation and thermal stability of the hydrate phase on the applied temperature cycling mode, and the technical features of the utilized PVT configuration. The experimental findings were complemented by a thermodynamic simulation model and other calculation approaches, with the aim to resolve the phase diagrams including the CO2 dissolution over the entire range of the applied (P, T) conditions.

The objective of this research project was to evaluate the effects of the addition of inorganic fillers into PEBA at various loading levels on the processing, mechanical, thermal and physical properties of the polymer. The composites investigated in this study were Pebax® 6333 SA01 MED (PEBA100) with 10 wt.%, 20 wt.% and 30 wt.% Barium Sulphate (PEBA/BaSO4) and Bismuth Oxychloride (PEBA/BiOCl) respectively. Composites were prepared using twin screw extrusion and injection moulding. Post-processing, composite samples were analysed for their mechanical properties (via tensile, impact and flexural analysis), thermal properties (via differential scanning calorimetry), rheological performance (via melt flow index) and physical properties (via density analysis and ash content testing). The results of which reveal how filler type and concentration influence PEBA composites. The results of the study suggest that BiOCl filler enhances the aesthetic properties, increases the stiffness, while maintaining some level of flexibility with minimal adverse effects on the tensile and impact strength. When comparing BiOCl to BaSO4 filled composites, it was clear that depending on the application of the polymer composite, BiOCl may provide more desirable properties. The study highlights the importance of optimising filler concentration and processing conditions to achieve desired composite properties for specific medical applications.

An inter- and transdisciplinary concept has been developed, focusing on the scaling of industrial circular construction using innovative compacted mineral mixtures (CMM) derived from various soil types (sand, silt, clay) and recycled mineral waste. The concept aims to accelerate the systemic transformation of the construction industry towards carbon neutrality by promoting the large-scale adoption and automation of CMM-based construction materials, which incorporate natural mineral components and recycled aggregates or industrial by-products. In close collaboration with international and domestic stakeholders in the construction sector, the concept explores the integration of various CMM-based construction methods for producing wall elements in conventional building construction. Leveraging a digital urban mining platform, the concept aims to standardize the production process and enable mass-scale production. The ultimate goal is to fully harness the potential of automated CMM-based wall elements as a fast, competitive, emission-free, and recyclable alternative to traditional masonry and concrete construction techniques. To achieve this objective, the concept draws upon the latest advances in soil mechanics, rheology, and automation and incorporates open-source digital platform technologies to enhance data accessibility, processing, and knowledge acquisition. This will bolster confidence in CMM-based technologies and facilitate their widespread adoption. The extraordinary transfer potential of this approach necessitates both basic and applied research. As such, the proposed transformative, inter- and transdisciplinary concept will be conducted and synthesized using a comprehensive, holistic, and transfer-oriented methodology.

We describe a vision for a national-scale heavy mineral (HM) map generated through automated mineralogical identification and quantification of HMs contained in floodplain sediments from large catchments covering most of Australia. The composition of the sediments reflects the dominant rock types in each catchment, with the generally resistant HMs largely preserving the mineralogical fingerprint of their host protoliths through the weathering-transport-deposition cycle. Heavy mineral presence/absence, absolute and relative abundance, and co-occurrence are metrics useful to map, discover and interpret catchment lithotype(s), geodynamic setting, magmatism, metamorphic grade, alteration or mineralization. Underpinning this vision is a pilot project, focusing on a subset of the national sediment sample archive, which is used to demonstrate the feasibility of the larger, national-scale project. We preview a bespoke, cloud-based mineral network analysis (MNA) tool to visualize, explore and discover relationships between HMs as well as between them and geological setting or mineral deposits. We envisage that the Heavy Mineral Map of Australia and MNA tool will contribute significantly to mineral prospectivity analysis and modeling here, particularly for technology critical elements and their host minerals, which are central to the global economy transitioning to a more sustainable, decarbonized paradigm.

The demand for polymer composites with improved mechanical and electrical properties is crucial for advanced aerospace, electronics, and energy storage applications. Single-walled carbon nanotubes (SWCNTs) and iron oxide (Fe₃O₄) nanoparticles are key fillers that enhance these properties, yet challenges like orientation, uniform dispersion, and agglomeration must be addressed to realize their full potential. This study focuses on developing SWCNTs/Fe₃O₄ epoxy composites by keeping the SWCNT concentration constant at 0.03 Vol.% and varying Fe₃O₄ concentrations at 0.1, 0.5, and 1 Vol.% with two different configurations: randomly orientated (R-) and magnetic field-assisted horizontally aligned (A-) SWCNTs/Fe3O4 epoxy composites and investigates the effects of filler concentration, dispersion, and magnetic alignment on the mechanical and electrical properties. The research reveals that both composite configurations achieve an optimal mechanical performance at 0.5 Vol.% Fe₃O₄, while A- SWCNTs/Fe3O4 epoxy composites outperformed at all concentrations. However, at 1 Vol.% Fe₃O₄, mechanical properties decline due to nanoparticle agglomeration, which disrupts stress distribution. In contrast, electrical conductivity peaks at 1 Vol.% Fe₃O₄, indicating that the higher density of Fe₃O₄ nanoparticles enhances the conductive network despite the mechanical losses. This study highlights the need for precise control over filler content and alignment to optimize mechanical strength and electrical conductivity in SWCNTs/Fe₃O₄ epoxy nanocomposites.

Composites with HDPE and PLA matrix have been tested to analyse the effect of natural fillers (wood flour, recycled waste paper and a mix of both fillers) and temperature on polymer degradation. Composting tests have been performed in both mesophilic (35°C) and thermophilic (58°C) conditions. Degradation development has been evaluated through mass variation, TGA and DSC. HDPE, as expected, did not display any relevant variation, confirming its stability under our composting conditions. PLA is sensibly influenced by temperature and humidity, with higher reduction of Mw when composting is performed at 58°C. Natural fillers seem to influence degradation process of composites, already at 35°C. In fact, degradation of fillers at 35°C allows a mass reduction during composting of composites, while neat PLA do not display any variation.

In this work we produced biochar by coffee waste and use it as filler in epoxy resin composite with the aim to increase their electrical properties. The biochar and biochar based composite electrical conductivity were studied in function of applied pressure and compared with carbon black and carbon black composite. The applied pressure has the aim to investigate the behaviour of filler in powder or dispersed in composite in function of compression. Results showed that even if the coffee biochar has less conductivity if compared with carbon black in powder form, it has better conductivity in composite if compared with carbon black. Composite mechanical properties were tested and they are generally improved respect to neat epoxy resin.

In the preparation of polymer-clay nanocomposites the chemical incompatibility between the clay surface and polyolefins can be overcome by using clays organically modified with short chain organic cations. The compatibility can be further enhanced by using functionalized polymer that wets the clay surface while being miscible with the non-polar polymer matrix. In this work we tried to modify the host polymer polypropylene (PP) by irradiating it with gamma-rays in air knowing that it undergoes oxidation and chain scission simultaneously. Thus lower molecular weight PP with highly polar surface due to oxidation can be expected to play double role of clay modifier and functional compatibilizer. This has been observed to be the case. Finely ground PP granules were irradiated in air in a ⁶⁰Co γ-irradiator at the dose rate of 0.08 kGy/h (low dose rate to enhance oxidation) to 5, 10, and 20 kGy total doses. The extent of oxidation and change in molecular weight were determined by ATR-FTIR and Melt Flow Rate measurements respectively. PP/MMT nanocomposites were prepared by using 20% γ-PP, 1-5 % MMT and pristine PP to make up the total 100 in a torque rheometer. Maleated PP was also used in similar quantities to compare the effectiveness of γ-PP as a compatibilizing agent. Nanocomposites prepared with 10 kGy irradiated PP was found to show optimum mechanical properties among all formulations, with 26% increase in E-modulus and 10% increase in tensile strength as compared to pristine PP. Ternary PP nanocomposites were characterized by XRD, SAXS and PALS studies.

The Kraaipan and Amalia greenstone belts in South Africa occurs in the western part of the Kaapvaal Craton. The two belts stretch discontinuously in an approximately north-south orientation over a distance of about 250 km from southern Botswana in the north to the Vaal River near Christiana in the south and are separated by a distance of about 90 km. Gold mineralization is hosted in banded iron-formation at both the Kalahari Goldridge deposit (Kalgold) in the Kraaipan greenstone belt in the north, and the Amalia deposit in the Amalia greenstone belt in the south, with the mineralization associated with quartz-carbonate veins. The footwall of these deposits is generally composed of mafic volcanic schist and hanging wall consisting of graywackes, schist and shale units. The Kalgold and Amalia gold deposits show some variation in the redox condition of the mineralizing system, mineralization temperatures and fluid chemistry. The ore mineral assemblage is characterized by magnetite-pyrrhotite-pyrite at Kalgold, which is indicative of reducing conditions, and magnetite-hematite-pyrite assemblage at Amalia that suggest a relatively oxidizing environment. Average mineralizing temperatures determined from chlorite geothermometry were relatively higher at the Kalahari Goldridge deposit ranging from 350 to 400oC compared to 335 to 370oC (mean, 352± 18, n = 113) at Amalia. The composition of the fluids derived from fluid inclusions are indicative of low salinity H2O-CH4-CO2-rich fluids at Kalgold against relatively H2O-CO2-rich fluids at Amalia. Evidence from strontium-carbon-oxygen isotopic ratios from carbonates suggests differences in redox conditions in the deposits could be attributed to different flow pathways by the evolving fluid from a common source (with minimum 87Sr/86Sr=0.70354) to the sites of gold deposition; with significant ore fluid interaction with thick sequence of carbonaceous meta-pelitic rock units at the Kalahari Goldridge deposit, that is absent in the Amalia deposit.

The Songpan-Ganze Orogenic Belt (SGOB) is bounded by the South China, North China, and Qiang-tang blocks and forms the eastern margin of the Tibetan Plateau. The Tiechanghe granite is located at the junction of the southeast margin of the SGOB and the western margin of the Yangtze Block. To elucidate the genetic relationship between the Tiechanghe granite and the surrounding molybdenum deposits in Western Sichuan, in this study, we conducted U-Pb zircon and molybdenite Re-Os isotopic dating. The results indicate that the Tiechanghe granite predominantly consists of monzogranite, with minor occur-rences of syenogranite, while the molybdenum deposits are mainly found in skarn and quartz veins. The laser ablation inductively coupled plasma mass spectrometry (LA-ICP-MS) U-Pb zircon ages of the Tiechanghe granite range from 162.9±0.7 Ma to 163.4±0.6 Ma, and the zircon LA-ICP-MS U-Pb age of the pegmatite veins is 164.1±0.9 Ma. These ages are consistent with the weighted average Re-Os age of the Ziershi molybdenite (160.3±1.6 Ma) within the error margins. These findings and previously ob-tained magmatic and metallogenic ages for the region suggest that a magmatic and mineralization event involving granite, molybdenum, tungsten, and copper occurred at around 162–164 Ma in the study area. This discovery broadens the exploration perspective for mineral resources in the Jiulong area of Western Sichuan and the entirety of Western Sichuan.

Alloy 800H stands as one of the few code qualified materials for fabricating in core and out of core components operating in high temperature reactors (HTRs). Welding is a common practice for assembling these components, however, the election of a suitable filler material is essential to enhance the high-temperature creep resistance of Alloy 800H weldments in high temperature applications. In this study, Inconel 625 and Haynes 230 filler material were used to weld the Alloy 800H plates employing the Gas Tungsten Arc Welding (GTAW) technique. The high temperature tensile, creep rupture property, microstructural stability and evolution of the weldments after high temperature exposure were investigated and compared with Alloy 800H. The results showed that the both weldments exhibited enhanced tensile and creep behavior at 760 oC. The creep rupture time of the weldments with Inconel 625 filler and Haynes 230 filler materials was about two and three time longer than that of Alloy 800H base metal when tested at 80 MPa and 760 oC, respectively. Carbides (MC and M23C6) were commonly observed in the microstructure of both the weld and base metals in the two weldments after high temperature creep tests. However, the Inconel 625 filler weldment displayed detrimental δ and Laves phase in the fusion zone and these precipitates could be potential sites for initiating cracks following prolonged high temperature exposure. The study showed that the weldment with Haynes 230 exhibited better phase stability and creep rupture property than the one with Inconel 625 filler material, suggesting its potential as a candidate filler material for Alloy 800H for further investigation. The finding also emphasizes the critical consideration of microstructural evolutions and phase stability in evaluating high temperature materials and their weldments in high temperature reactor applications.

Background: Several trace minerals have been shown to be associated with thyroid cancer. However, there is a paucity of data on the characteristics of thyroid nodules in different mineral rich regions of the Democratic Republic of Congo (DRC). The objective of this study is to establish the spectrum of thyroid nodules in different regions of the most mineral wealthy country in the world. Method: We conducted a cross-sectional study, performing descriptive statistics and logistic regression with a p value < 0.05 deemed of statistical significance. We enrolled 529 patients diagnosed with thyroid nodules between 2005 and 2019 in two of the richest provinces in minerals (Katanga and South Kivu) and the capital city, Kinshasa. Results: The mean age was 44.2±14.6 years with a female predominance, with a female to male ratio of 5.4. 66.5% of patients had a family history of thyroid disease. 74 patients had simple nodules, whereas 455 had multiple nodules. 87.7% of patients with nodules were euthyroid. The nodules mostly presented a solid structure (72.2%), hypoechogenicity (84.5%), a macronodule (59.8%), calcification (14.4%) and lymphadenopathy (15.5%). 22.3% of these nodules had a malignant character. The independent factors associated with this malignancy were age ≥60 years (aOR=2.81), Katanga as province of origin (aOR=8.19), solid echostructure (aOR=7.69), hypoechogenicity (aOR=14.19), macronodule (aOR=9.13), calcification (aOR=2.6) and the presence of adenopathy (aOR=6.94). Conclusion: By the way of this first of its kind study, we demonstrated that thyroid nodules were more likely to be malignant if found in patients originating from mineral rich region of Katanga. This high frequency of malignancy in mineral rich regions requires measures aimed at early detection in this population, lower threshold for suspicion of malignancy and adequate training of doctors involved in the management of these patients. This study paves the way for future, more extensive and well-funded studies to better understand the relationship of heavy metals and thyroid cancer incidence in the richest country in heavy metals in the world.

In recent years, intelligent identification and prediction of ore deposits based on deep learning algorithm and image processing technology has gradually become one of the research frontiers in the field of geological and metallogenic prediction. However, this method also has many problems that need to be solved. For example, (1) very few trainable image samples containing mineral point labels; (2) The geological image features are small and irregular, and the image similarity is high; (3) It is difficult to calculate the influence of different geological prospecting factors on ore mineralization. Based on this, this paper constructs a deep learning network model Multiscale Feature Attention Framework (MFAF) based on geo-image data. The results show that MFCA-Net module in MFAF model can solve the problem of scarce mine label images to a certain extent. In addition, the channel attention mechanism SE-Net module can quantify the difference of influence of different source factors on mineralization. The prediction map is obtained by applying the MFAF model in the study of deposit identification and prediction in the research area of the southern section of Qin-hang metallogenic Belt. In the forecast map, many regions have high metallogenic potential. Through observation, it is found that the above predicted area covers 100% of the known ore deposits at present, which has a good prediction effect. Later, we can find out the specific reasons through field verification. The multi-scale feature fusion and attention mechanism MFA Framework in this paper can provide a new way of thinking for geologists in mineral exploration. The research of this paper also provides resource guarantee and technical support for the sustainable exploitation of mineral resources and the sustainable growth of society and economy.

This paper deals with experimental study of the influence of conductive (Fe₃O₄) and insulating (Al₂O₃) nanostructured particles at various concentrations on the dielectric strength of transformer mineral oil. The method of preparation and characterization of these nanofluids (NFs) through the measurements of zeta potential, the real and imaginary parts of dielectric constant as well as the concentration and size of nanoparticles using Scanning Electron Microscope (SEM) images of nanoparticles powders and Dispersive x-ray Spectroscopy (EDS) analysis are presented. Experimental findings reveal that these two types of nanoparticles materials significantly improve AC breakdown voltage and the magnitude of this improvement depends on the concentration, size and nature (material) of nanoparticles. For a given type of nanoparticles, the effect is more marked with the smallest nanoparticles. The conductive nanoparticles offer higher enhancement of dielectric strength compared with insulating nanoparticles based nanofluids. With Fe₃O₄, the breakdown voltage (BDV) can exceed twice that of mineral oil and it increases by more than 76% with Al₂O₃. The physicochemical mechanisms implicated in this improvement are discussed.

This study was aimed at investigating the protective effects of glass ionomer cement (GIC) and surface pre-reacted glass ionomer (S-PRG) fillers used as dental restorative materials on demineralization of bovine enamel. GlasIonomer FX ULTRA (FXU), Fuji IX GP Extra (FIXE), CAREDYNE RESTORE (CDR) were used as GICs. PRG Barrier Coat (BC) was used as the S-PRG filler. They were incubated in a lactic acid solution (pH = 4.0) for 6 d at a temperature of 37 °C. The mineral was etched from the enamel surface, and a large number of Ca and P ions were detected in solution. The Al, F, Na, Sr, and Sr ions were released in GICs and S-RPG fillers. The Zn ion was released only in CDR and the B ion was released only in BC. The presence of apparent enamel prism peripheries was observed after 6 d of treatment for the group containing only enamel blocks. pH values for the FXU, FIXE, CDR, BC, and enamel block groups after 6 d were 6.5, 6.6, 6.7, 5.9, and 5.1, respectively. Therefore, the observed pH neutralization effect suppressed progression of caries due to the release of several ions from the restoratives.

The developed microstructure features a long with mechanical properties in vacuum brazing of commercially pure Ti-alloy using Ti₂₀Zr₂₀Cu_60-x-Ni_x (x=10, 20, 30, 40 and 50) metallic filler. Brazing temperatures and holding times employed in this study were 1240-1279 K (967-1006^oC) for a period of 10 min, respectively. The mechanical properties of brazed joints were evaluated by nanoindention at a constant peak load of 5000 μN and tensile tests. The number of intermetallic phase, such as NiTi₂, Ti₂Cu, (Ti, Zr)₂Cu, (Ti, Zr)₂Ni, β(Ti, Zr), α-Ti and NiTi. The solid solution matrix have been identified at 1279 K out of these different regions the NiTi₂ rich region had the highest nanohardness of 17 GPa, It is interesting to note that among five different glasses, the Ti₂₀Zr₂₀Cu₁₀Ni₅₀ has the highest yield strength of 17 GPa, which is mainly due to NiTi₂ phase. Based on the tensile test results all cracks propagate along the brittle intermetallic compounds like NiTi₂ in the reaction layer the reduction of the strength of the joints and fracture behaviour upon propagation of the crack, which shows the morphological cleavage including facets characteristics.

Until recently, the classic approach to mineral exploration studies is to bring the field samples/drill cores collected during field studies to the laboratory followed by laborious analysis procedures to generate the analytical data. This is very expensive, time consuming and difficult for exploring vast areas. But rapid technological advances in field portable analytical instruments such as portable ultraviolet–visible and near-infrared spectrophotometers, gamma ray spectrometer, pXRF, pXRD, pLIBS, and µRaman spectrometer have changed this scenario completely and increased their on-site applications in mineral exploration studies. These instruments are currently providing direct, rapid, on-site, real-time, non-destructive, cost-effective identification, and determination of target elements, indicator minerals and pathfinder elements in rock, soil, and sediment samples. These portable analytical instruments are currently helping to obtain accurate chemical and mineralogical information directly in field with minimal or no sample preparation, and providing decision-making support during field work as well as during drilling operations in several successful mineral exploration programs. In this article, the developments in these portable devices, and their contributions in the platinum group elements (PGE), rare earth elements (REE), gold, base metals, and lithium exploration studies both on land and on ocean bed have been summarized with examples.

Mineral identification is an important part of geological analysis. Traditional identification methods rely on either the experiences of the appraisers or the various measuring instruments and the methods are either easily influenced by the experiences or need too much work. To solve the above problems, there have been studies using image recognition and intelligent algorithms to identify minerals. But the current studies can not identify many minerals, and the accuracy is low. To increase the number of identified mineral categories and the accuracy, we proposed the method that uses both the mineral images and the Mohs hardness in the deep neural networks to identify the minerals. The experimental results showed that the method can reach 94.0% Top-1 accuracy and 99.9% Top-5 accuracy for 28 common minerals. The model that combines image and Mohs hardness together can identify more minerals and increase the accuracy using less training data.

Dietary supplements are more and more often used to increase daily intake of essential vitamins and minerals. These preparations are classified as special category of foods and are subject to food law, not pharmaceutical regulations. As a result the requirements to dietary supplements are much less restrictive than to medications. Also simple and inexpensive procedure of registration causes that the number of dietary supplements is widely spread every year. On every manufacturing phases of dietary supplements, there is a risk of contamination. One of the pollutions might be mercury which is classified as heavy metal. Its inorganic compounds damage kidneys and liver and methylmercury is easily absorbed from gastrointestinal system. Methylmercury is distributed in all tissues, also in nervous system. The aim of study was to determine the level of mercury in multivitamins and multiminerals preparations and to analyze the results. The study included 22 dietary supplements containing vitamins and minerals available on Polish market. Mercury was analyzed with atomic absorption spectrometry using AMA 254. The concentrations of Hg was 0.22–5.85 µg/kg (the average content was 2.40 µg/kg). The highest average mercury content was 4.51 µg/kg, whereas the lowest one was 0.31 µg/kg. The results was also analyzed in individual groups depending on main component and indication for use as well as pharmaceutical formulation. Also according to manufacturer’s recommendation, the dose of mercury taken with a single medicine was estimated for time of a day, a week, a month, 3 months and also a year. The findings were compared to limits defined in regulations of European Union and PTWI set by JECFA to assess the health risk. The results presented in this study proved that the amount of mercury in tested dietary supplements is much lower than the value of valid regulations. Analyzed supplements as long as they are used with the recommendation of manufacturer, do not pose a threat to human health.

Due to its size, wood dust often plays the role of a raw material used as a source of energy. However, it is nevertheless an unavoidable byproduct generated during the milling of wood or wood-based composites. The research presented here is focused on the selected properties of 3-layer plywood, produced with the utilization of dust from the milling of three-layer particleboard as a filler in the bonding mass. Four types of filler were used in the study: commercial rye flour, wood dust naturally occurring in the composition of particles used industrially for particleboard production, wood dust from the first batch of shredded particleboard, and dust from the second round of milled particleboard. In the context of this investigation, the highest modulus of elasticity (MOE) values were observed in reference samples. Conversely, for samples featuring filler material from the initial milling process, there were no substantial differences in filler content. Notably, in samples where the filler was sourced from the secondary milling of particleboard, the modulus of elasticity exhibited an upward trend in conjunction with increasing filler content. A similar trend was observed in samples utilizing the naturally occurring dust. Meanwhile, the modulus of rupture (MOR) decreased with an elevated degree of milling, though it displayed a slight increase as the filler content increased. With regard to shear strength testing, the most favorable outcomes were achieved in samples incorporating filler material from the initial milling of particleboard. The thickness swelling of the plywood reached its peak in variants utilizing filler material from both the initial and secondary milling of particleboards. In contrast, water absorption testing exhibited a more pronounced response in the newly introduced variants, although samples incorporating filler from the initial and secondary milling processes eventually yielded results akin to the reference sample, with the naturally occurring dust displaying higher water absorption values. In terms of density profiles, the highest density values were observed in samples utilizing rye flour as the filler material. A similar density profile was observed in samples with 5 parts of wood flour as filler, although the density of the adhesive was slightly lower in these cases. An increase in the quantity of wooden filler material resulted in a commensurate increase in plywood thickness. The research confirms the possibility of using the aforementioned dust as an alternative to conventional fillers in plywood technology. It also raises the question of how to effectively remove glue residues from wood-based composite dust, which would enhance their absorption properties.

The article presents the results of research on the production of effective inorganic fillers and chemically resistant composite polymer-mineral materials based on industrial waste. The aim of the work is to develop the technological foundations for the production of inorganic fillers and highly filled filling compositions for use in chlorine-containing media. Materials with high resistance to hydrochloric acid are graphite and quartz sand. Thermal power plant (TPP) ash was used as an acid-resistant filler in the compositions. The simplex lattice planning method was used to determine the areas of compositions with the best properties. Two components were selected: formaldehyde rubber resin and mineral filler (TPP ash) as a binder. As the third component, hydrolytically active fillers were used - anhydrite, phosphogypsum and phosphorus production slag. A preliminary operation was performed to remove hygroscopic moisture from the filler.The influence of the nature of mineral fillers on the chemical stability and durability of the obtained composites is investigated. The nature of the interaction of mineral fillers with a polymer binder was determined, and chemical interaction of the hydroxyl groups of the filler and the methyl groups of the polymer took place. The mathematical planning method was used to optimize the chemical resistance and durability of the compositions of the studied substances. Based on the results of this study, optimal compositions of compositions, anhydrite, phosphogypsum and phosphoric slag were selected. These composites, with the highest possible degree of filling, have high target characteristics.

This review explores the potential of microalgae as a sustainable and nutritionally rich alternative for mineral supplementation in poultry diets, addressing both the opportunities and challenges in this emerging field. Poultry nutrition, pivotal to the health and productivity of birds, traditionally relies on inorganic and organic mineral sources, which, while effective, raise environmental and economic concerns. Microalgae offer a promising solution with their high content of essential minerals, proteins, vitamins, and bioactive compounds. The review delves into the nutritional profile of various microalgae, highlighting their rich mineral content, crucial for physiological processes in poultry. It examines the bioavailability of these minerals and their impact on poultry health and productivity. Furthermore, it evaluates the environmental sustainability of microalgae cultivation and acknowledges the challenges in using microalgae in poultry diets, particularly in terms of the economic viability of large-scale production and the consistency of nutrient composition. It discusses the importance of rigorous safety assessments and regulatory compliance, given the potential risks of toxins and heavy metals. Overall, this analysis aims to provide a clear understanding of the role microalgae could play in poultry nutrition and address sustainability challenges in animal agriculture, while also considering future perspectives and advancements needed in this field.

As semi-airborne mineral exploration has limited budgets, it is critical to design experimental procedures that generate data maximizing the desired information We investigate the effects of transmitter-receiver geometries for a variety of anomalies and semi-airborne layouts. Our simulations indicate that 200 m flight line spacing and 100 m point distance are the optimal trade-off between coverage and survey progress for various targets. Based on the target size and distance between the transmitter and the target, the transmitter length should be at least equal to the length of the target and for more than 1 km, at least two or three times the target size. Likewise important are the location and direction of the transmitter cables, which can have great impact on the result of inversion and should be parallel to the target strike. By using more than one transmitter, better results are obtained. If the strike of the target is known, transmitters should be parallel to each other and if not, it is better to use perpendicular transmitters. Results showed that the optimal distance between transmitters is 3 km. Our simulations show that it is even possible to recover targets just below the transmitter in corresponding areas of masked data.

The climate change impacts on some regions of the planet faster and stronger. These areas are known as the hot spots for climate change and Cyprus (Nicosia) in the Mediterranean is one of these spots. This paper aims to analyze the significant changes of atmospheric aerosol characteristics in 2019 and during the extreme event of 25 April 2019. We study the aerosol optical thickness (AOT), Ångström exponent, single scattering albedo, refractive index (imaginary and real parts), size, and vertical distribution of aerosol particles during the event of a high atmospheric aerosol contamination over Nicosia in details. For this purpose, we used the ground-based lidar, observations of the sun-photometer AERONET Nicosia station, satellite products from the Moderate Resolution Imaging Spectroradiometer (MODIS), and back trajectories of air movements calculated using the Hybrid Single Particle Lagrangian Integrated Trajectory Model (HYSPLIT). On 23–25 April, according to lidar and sun-photometer observations, strong aerosol pollution over Nicosia was detected. On April 25, 2019, the AOT value exceeds 1.0 at λ = 440 nm. Analysis of the optical and microphysical characteristics supported that the pollution consists of mainly Saharan dust and partly urban aerosols. This assumption was confirmed by HYSPLIT backward trajectories and MODIS images where air masses containing dust particles came from North Africa and from the Eastern part of Europe.

Nutrient management of lowbush blueberry (Vaccinium angustifolium Ait.) depends on several yield-limiting features. Machine learning models can process such yield-impacting variables to predict berry yield. We investigated the effects of local variables on yields and nutrient management of lowbush blueberry. We collected 1504 observations from N-P-K fertilizer trials conducted in Quebec, Canada. Meteorological indices at various phenological stages showed the greatest impact on yield. High mean temperature at flower bud opening and after fruit maturation, and total precipitation at flowering showed positive effects. Low mean temperature and low total precipitation before bud opening, at flowering, and by fruit maturity, as well as number of freezing days (< -5ºC) before flower bud opening, showed negative effects. Soil fertility variables, leaf nutrient compositions and N-P-K fertilization showed smaller effects. Gaussian processes predicted berry yields from historical weather data, soil analysis, fertilizer dosage, and leaf nutrients with a root-mean-square-error of 1447 kg ha-1 on the testing data set. An in-house Markov chain algorithm optimized yields modelled with Gaussian processes from leaf nutrient composition, soil test value, and fertilizer dosage conditioned to specified historical weather features. We propose to use conditioned machine learning models to manage nutrients of lowbush blueberry at local scale.

This work describes and interprets the presence of heavy minerals in the western Portuguese continental margin using a set of 78 bottom samples collected from 3 distinct areas of this margin: Porto, Aveiro and Nazaré canyon head areas. The main transparent heavy mineral suite (minerals with frequencies >10%), is composed by amphiboles (hornblende), mica (biotite), andalusite, tourmaline and garnet. A secondary suite (minerals with frequencies between 1 and 10%), is composed by pyroxene (enstatite, diopside and augite), staurolite, zircon and apatite. With very low frequency representing less than 1% we found rutile, olivine, kyanite, monazite, epidote, sphene, anatase, sillimanite and brookite. The main primary sources (igneous and metamorphic rocks) explain the presence of these minerals. However, the application of the principal component analysis, with a previous application of the centered log ratio transformation of the heavy mineral data, also stresses for the importance of the grain sorting as a process in controlling the heavy mineral occurrence. The importance of this process is mostly sustained by the distribution pattern of mica and of the most flattened amphibole grains in a way that these particles tend to have a hydraulic affinity to finer grained sediments.

In recent years, technical processes for the sequestration of CO2 through industrial waste mineral carbonation have been explored and developed. There is a large portfolio of Carbon Capture, Uti-lisation and Storage (CCUS) techniques that have been employed on a laboratory and at pilot scale. These include geological storage, ocean storage and mineralisation by carbonate ores. In view of this, the main purpose of this research was to investigate and explore chemical variables, particularly ammonium salts as lixiviants for calcium mineral extraction from iron making slag. The slag in use was acquired from a Steel Mill in the Vaal Triangle Region in Gauteng, South Af-rica. The experimental test work was conducted using different ammonium lixiviants, namely, NH4NO3, NH4Cl and CH3COONH4 to understand the influence of anion type as well as possible differences in mechanisms of interactions. Lixiviant concentration as well as the reaction time were varied in this research study. The three selected ammonium based lixiviants showed different extents of calcium extraction owing to differences in the anion groups. NH4NO3, NH4Cl and CH3COONH4 were found capable of dissolving 50% to 80% of calcium from the selected slag for different molar concentrations. Anion type and leaching time also had significant influences on the leaching of calcium from the slag. Rapid pH degradation resulted in better calcium extraction ca-pabilities. This work has shown that the selected ammonium salts have a potential as lixiviants for calcium dissolution from iron making blast furnace slags. These lixiviants would therefore be important to consider during calcium mineral carbonation for CO2 sequestration.

The present study investigation, our results on characterization of commercially pure-Ti alloy brazed with metallic glass ribbons of Ti20Zr20Cu60-xNix (x = 30, 40, and 50) metallic glass ribbons were produced using a vacuum melt spinner. These ribbons were then used as filler materials for vacuum brazing of two Ti alloy plates at 1268, 1277 and 1279 K for a period of 10 min. Field-Emission Scanning Electron Microscopy (FESEM), Transmission Electron Microscopy (TEM) and the energy dispersive X-ray spectroscopy (EDX). The as-spun ribbons showed fully amorphous structure when examined on both surfaces by XRD and also verified by TEM investigation. The brazing joint of two Ti-plates using the metallic glass ribbon when brazed with Ni50 was found to be of very high strength. FESEM characterization of the cross-section of the brazed joints shows sub-micron size grains uniformly distributed in the matrix with brighter appearance. FESEM and EDX analysis revealed that the sub-micron grains are rich in Ti & Ni while the matrix phase mainly consisted of Ti. BSE image along with EDS Analysis indicated that the brazed joint has a presence of NiTi2 and Cu2 (Ni Zr) phases which could be responsible for increase in the strength of the brazed joint.

The carbonation of industrial calcium-rich byproducts such as steel slag demonstrates significant potential for CO2 sequestration. This technique aids in reducing carbon emissions while also promoting waste recycling. Despite its advantages, gaps remain in understanding how steel slag characteristics and operational parameters influence the carbonation process, as well as the underlying mechanism of direct aqueous carbonation. We evaluated the carbonation performance of three types of steel slag at temperatures below 100°C using a gas–liquid–solid reaction system. The slag with the highest CO2 sequestration capacity was chosen for a systematic evaluation of the effects of operating conditions on carbonation efficiency. Thermodynamic analysis indicated that the reactivity of CaO and Ca(OH)2 with CO2 exceeded that of CaO•SiO2 and 2CaO•SiO2. Under conditions of 85°C, a particle size less than 75 μm, an initial CO2 pressure of 0.5 MPa, a liquid-to-solid ratio of 5 mL/g, and a stirring speed of 200 rpm, the steel slag achieved a sequestration capacity (K) of 283.5 gCO2/kg and a carbonation efficiency (ζCa) of 51.61%. Characterization of the slag before and after carbonation using X-ray diffraction, SEM‒EDS, thermogravimetric analysis, and Fourier transform infrared spectrometry confirmed the formation of new carbonates. Mechanistic analysis revealed that the rate-limiting step initially involved the mass transfer of CO2, transitioning to Ca2+ mass transfer as time progressed. Our research provides a viable technique for CO2 capture and a beneficial approach for reutilizing waste steel slag. Furthermore, solid residues after capturing CO2 have the potential for conversion into carbon-negative building materials, offering a sustainable strategy for steel companies and other enterprises with high carbon emissions.

Microbial-mediated biogeochemical cycling of iron is widespread in anaerobic environments such as sediments and deep Earth aquifers, and is one of the major pathways for metabolising iron in nature. Organic matter containing quinone groups can act as electron shuttles to transfer electrons between microorganisms and Fe(III) oxides, facilitating the biotransformation of iron; this process also influences the transport transformation of pollutants. In this paper, the reduction of Fe(III) oxides by aniline in the heterogeneous iron-reducing bacterium Shewanella oneidensis MR-1 mediated by the electron shuttle AQS was investigated. The results showed that aniline significantly promoted the reduction of Fe(III) by MR-1 in the AQS-mediated reaction, and the best Fe(III) reduction was achieved in the reaction group of "GT+MR-1+0.5mM AQS+3μM aniline", in which the Fe(II) production was significantly higher than that in the reaction groups of only microorganisms and no aniline reaction. The amount of Fe(II) produced was significantly higher than that of the microorganism-only and aniline-free reaction groups, and the addition of aniline also significantly increased the consumption of sodium lactate by MR-1 in the reaction system. The solid mineral Fe(II)-O content increased to 41.32% after the reaction. However, the structure of needle ferrite is relatively stable, and the surface morphology did not change significantly by SEM, and the generation of other secondary minerals was not observed in the XRD results. The results of this experimental study can help to understand the biogeochemical cycle of iron in multicomponent reactions and are of great significance for environmental management.

In this paper, mineralogical and elemental geochemical characteristics of massive sulfide samples collected from Jade hydrothermal field, located in the Izena depression in the central graben of Okinawa Trough, were analyzed by means of optical microscopy, scanning electron microscopy and electron probe. The results show that the sulfide in Jade hydrothermal area can be divided into Zn-Cu-Pb rich massive sulfide and Zn-Fe rich massive sulfide. The former is composed of sphalerite, galena, anglesite, chalcopyrite and pyrite, and its formation stage can be divided into pyrite stage, sphalerite-chalcopyrite stage, anglesite stage and colloidal pyrite stage. The latter is mainly composed of sphalerite, pyrite, marcasite and a small amount of galena, which can be divided into galena stage, pyrite stage, sphalerite stage, pyrite and marcasite stage. Cu and Zn in pyrite may exist in the form of microinclusions, while Ag and Pb may exist in pyrite in the form of fine galena inclusions containing Ag. Fe and Cu may enter sphalerite in the form of ion replacement. Zn may enter chalcopyrite in the form of ion replacement, and As and Pb may be inclusions in chalcopyrite as As-bearing galena inclusions. Consistent with the previous understanding, the metal elements in the hydrothermal liquid system in Jade hydrothermal field mostly migrate with the hydrothermal fluid as sulfur complexes, and when the hydrothermal fluid mixes with seawater, the physical and chemical conditions of the fluid change, resulting in sulfide mineral precipitation. However, the chemical structure of chalcopyrite is still controversial, which restricts the understanding of the substitution mechanism of trace elements during chalcopyrite precipitation.

The circular economy is based on maintaining a circular flow of resources. Policymakers face difficulties in balancing national security and circular economy aspects in the field of mineral resources policy. With a uniquely expanded input-output table, this study estimates the final destination of several critical minerals (lithium, cobalt, yttrium, lanthanum, cerium, neodymium and dysprosium) and base metals (iron, copper and aluminum) in the Japanese economy for 2015. Our model shows quite a good similarity between the estimated composition and the actual data of products. The results reveal a detailed distribution of critical minerals and indicate prioritized implementation for creating and maintaining a circular flow of critical minerals. Developed decision flow guidance provides a comprehensive approach to national security and circular economy aspects for policymakers. For further actions, inclusive indicator development is required for policymakers to support the determination of implementation possibilities from social and technological aspects.

Butadiene-Styrene copolymer (SBS) to improve the mechanical and deformation properties of the binder used in its manufacture. However, the high cost and variability of processing limit its performance. A secondary modifier to solve these problems is nano and micro materials that allow the generation of unique properties in polymeric systems. Based on this, this study experimented with fly ash micro filler ((FA) in low proportions as a binder modifier with SBS for use in PA mixes. The FA residue is considered in 3% and 5% dosages on a base binder with 5% SBS. Rheological results show that FA improves classical, linear viscoelastic (LVE), and progressive damage properties compared to the modified binder. The PA blends with FA reduced binder runout, resulting in a thicker film, showing better abrasion resistance in dry and wet conditions. Samples with FA increase the post-cracking energy in indirect tension due to higher ductility. However, they decrease the fracture energy due to higher cracking before failure. In addition, the FA manages to decrease the difference between dry and wet ITS.

The roots of African grapes (Lannea microcarpa) have long been utilised in traditional medicine for their perceived therapeutic properties. However, their comprehensive proximate and mineral analysis remains largely unexplored. Proximate composition and mineral content of the roots were conducted. The sample was obtained from Katsayal, Katsina State, and analysed using standard procedures. The macro and micro metals were determined using Flame Photometer and Atomic Absorption Spectroscopy, respectively. The results revealed a moisture content of 28.0 ±2.0%, an ash content of 21.3±1.2%, and significant levels of crude fibre (29.0±0.50%), crude lipid (9.60±0.20%), crude protein (6.91±0.01%), and available carbohydrates (33.3±0.10%). The calorific value of the root was determined to be 245 ± 0.01 kcal/g. The micro-mineral analysis revealed the detection of copper (8.60 ± 0.002 mg/kg), magnesium (9.24 ± 0.004 mg/kg), manganese (41.9 ± 0.001 mg/kg), iron (405 ± 0.042 mg/kg), and zinc (9.46 ± 0.001 mg/kg). The macro-minerals, namely calcium (28400 mg/kg), potassium (1530 mg/kg), and sodium (45030 mg/kg), were found to be present in the sample. It is advisable to conduct additional research to examine the identified minerals' bioavailability, clarify the phytochemical profile, and investigate potential bioactive compounds.

Mineral profile of beef interests human health, but also animal performance and meat quality. This study analyzes the relationships of 20 minerals in beef (ICP-OES) with 3 animal performance and 13 meat quality traits analyzed on 182 samples of Longissimus thoracis. Animals’ breed and sex showed limited effects. The major sources of variation (farm/date of slaughter, individual animal within group and side/sample within animal) differed greatly from trait to trait. Mineral contents were correlated to animal performance and meat quality being significant 52 out of the 320 correlations at the farm/date level, and 101 out of the 320 at the individual animal level. Five latent factors explained 69% of mineral co-variation. The most important, “Mineral quantity” factor correlated with age at slaughter and with the meat color traits. Two latent factors (“Na+Fe+Cu” and “Fe+Mn”) correlated with performance and meat color traits. Two other (“K-B-Pb” and “Zn”) correlated with meat chemical composition and the latter also with carcass weight and daily gain, and meat color traits. Meat cooking losses correlated with “K-B-Pb”. Latent factor analysis appears be a useful means of disentangling the very complex relationships that the minerals in meat have with animal performance and meat quality traits.

Filter Media (FM) sourced from recycled organic and mineral material offers a low cost and effective means of treating urban stormwater. Using recycled materials rather than from an increasingly scarce source of virgin materials (typically sandy loam soil) can ensure a sustainable long-term economy and environment. This paper presents results from the laboratory analysis and mathematical modeling to highlight the performance of recycled organic and mineral material in removing nutrients and metals from stormwater. Analysis included physical and chemical characterisation such as particle size distribution, saturated hydraulic conductivity (Ksat), bulk density, effective cation exchange capacity, and pollutant removal performance. Design mixes (DM), comprising a combination of organic and mineral materials, were characterised and used to develop/derive modelling design within the Model for Urban Stormwater Improvement Conceptualisation (MUSIC v6) [1]. Comparison is made to the Adoption Guidelines for Stormwater Biofiltration Systems - Summary Report [2] which were based on the Facility for Advancing Water Biofiltration (FAWB) guidelines to assist in the development of biofiltration systems, including the planning, design, construction and operation of those systems. An observed outcome from over two decades of biofiltration guideline development has been the exclusion of alternative biofilter materials due to claims of excessive leaching. Results from this study indicate that high nutrient and metal removal rates can be achieved over a range of hydraulic conductivities using design mixes of recycled organic and mineral materials that have a demonstrated equivalence to existing guideline specifications.

While the demand in reduction of CO₂ increases, the need for CO₂ sequestration processes is very high. One promising technology is the Carbon Capture and Storage (CCS). In this paper we refer to several papers which study the three main steps in CCS chain. CO₂ capture technologies, CO₂ transportation to the storage sites and the very critical step the CO₂ storage. Recently a novel method (mineral carbonation) for CO₂ sequestration has been proposed which is based in the reaction of CO₂ with calcium or magnesium oxides or hydroxides to form stable carbonate materials. Greece is a country that emits CO₂ mainly from the lignite fired power plant in Western Greece. After the study of the bibliographic references about the use of mineral carbonation process while injecting CO₂ in the appropriate geological forms we concluded that there are also these forms in our country and mainly in the area near to the power plant such as in sites Vourinos and Pindos. In these sites exist minerals rich in oxides and hydroxides of Ca, Mg and Fe representing the perfect materials for mineral carbonation.

To address the question whether there is evidence that drinking water in general or mineral water in particular is effective in preventing diabetes; we performed a literature search of randomized controlled trials (PubMed). The search resulted in very few trials (N = 9) investigating this topic: one trial investigates the effect of increasing water consumption on glycemic control in diabetic patients; two trials investigate the effect of drinking water with a meal in diabetic patients; while six trials compare the effect of mineral rich water with that of low mineralized water on glucose metabolism in healthy subjects. There is evidence that increasing water consumption can improve glucose metabolism and randomized controlled trials with mineral water suggest that waters containing relevant amounts of magnesium can exert an additional effect. The role of bicarbonate; which is present in all the mineral waters used in the trials; will be discussed. Future research needs to investigate the effect of mineral water in prediabetic individuals or individuals with impaired glycemic control.

In no-tillage systems, there is an accumulation of crop residues (CR) which plays an important role in available of soil-N. A study was set up to provide information regarding the CR N credit, and the influence of N mineral fertilizer. An incubation was run in a loam soil with addition of a similar rate of residue (10 Mg ha-1; sugarcane, soybean, and brachiaria) and N mineral fertilizer (urea; 120 kg N ha-1). After the stabilization of biological activity, soil and remaining residues were collected, and N monitored. Results showed that the N credit was positive with application of soybean, sugarcane, and brachiaria. There was an expressive performance of soybean N credit represented by a positive balance, and a reduction from 2.49 to 0.9 g kg-1 of N in residue, with direct increase of 90% of soil-N. There is no need of N fertilizer to potentialize the soybean N credit, but it is requested to potentialize N credit of brachiaria and sugarcane. The urea demonstrated be a good enhancer of brachiaria N credit, but it was not adequate to sugarcane residues. Based in our result, the accumulation and incorporation of CR can be considered as a N credit with positive contribution in soil-N.

This study assessed the impact of mineral fertilization on tuber yield and food quality of yam genotypes, specifically Dioscorea alata and Dioscorea rotundata. Four genotypes, each from D. alata and D. rotundata, were used in field experiments conducted in Ibadan, Nigeria, in the 2017 and 2018 cropping seasons. Experiments were conducted under low soil NPK fertility conditions with and without fertiliser treatments. A recommended NPK rate for the area (90, 50, and 75 Kg N, P, K ha-1) was applied to plots with fertiliser treatment. Tuber yield, functional and pasting properties of yam flour, and sensory attributes of pounded yams were collected. The results showed differential responses of the genotypes to tuber yield and food quality with fertiliser application. Fertiliser application has generally increased fresh tuber yield, but it has affected some genotypes' flour quality and textural attributes of the pounded yams. As regards genotypes Danacha and TDa0200012, fertiliser application has increased tuber yield without causing a decrease in tuber quality hence, suggesting Danacha and TDa0200012 as suitable genotypes for maximizing fertiliser productivity. However, in another genotype Ojuiyawo, fertiliser application effectively increased tuber yield but deteriorated tuber quality. Our results suggested that it is crucial to determine the impact of fertilisation on tuber yield and quality for each genotype and select the appropriate genotype to improve productivity through mineral fertilisation. The results of this study can be widely applied to enhance yam productivity in sub-Saharan Africa and useful for sustainable agriculture in yam-growing areas.

Arsenic, an element of environmental impact, can be incorporated into jarosite–type compounds and remain stabilised within the structure under a wide range of environmental conditions. In this study, a sample of ammonium–arsenic jarosite was synthesised by precipitation in sulphate medium at controlled pH of 1.2–1.8. The behaviour of arsenic during the thermal and chemical decomposition of jarosite was analysed; the degradation in alkaline medium of jarosite was also studied. According to the results, the synthesised jarosite is composed of joined rhombohedral crystals, forming tightly spherical shaped particles, 37–54 μm size. The ammonium jarosite produced possessed a high arsenic concentration; its calculated stoichiometry being (NH₄)Fe_2.45[(SO₄)_1.80(AsO₄)_0.20][(OH)_4.15(H₂0)_1.85]. It was found that arsenic is stabilised in the jarosite structure; upon heating, it remains in residual solids above 700°C, whilst in alkaline medium an incongruent dissolution takes place, with the arsenic retained in the solid phase along with iron. These solids, when exposed to high temperatures (1200°C), transform into a type of iron oxide known as hematite, so with arsenic it is retained an iron compound forming a stable compound which withstands high temperatures.

This study compared the relative effect of two trace mineral supplementation strategies recom-mended in France for newborn beef calves. 600 calves were supplemented with 20 mg oral sele-nium (OTM group) at birth (D0) or by injection (ITM group) of a multi-mineral solution (60 mg of Zn, 10 mg of Mn, 15 mg of Cu, 5 mg of Se) on D0, D30 and D60. Mortality and the incidence rate of diseases, including diarrhea, omphalitis, pneumonia, as well as medicinal treatments, were recorded from D0 to D210. The incidence rate of omphalitis was significantly lower in the ITM group than in the OTM group (respectively 11% vs. 17%, P = 0.036). The cumulative inci-dence rate of all health troubles was lower in the ITM group than in the OTM group (P=0.007). Except for pneumonia, incidence of diarrhea (24% vs. 22%), use of oral (7% vs. 6%) or IV rehydra-tion therapy (4% vs. 2%) or use of antibiotics (43.3% vs. 38.0%) and mortality (3% vs 2%) were numerically higher in OTM group than in ITM group (n.s.). In this study, ITM supplementation is as efficient as oral supplementation regarding calves' health status. It reduces the risk of ompha-litis at the calf level effectively.

This study aims to assess the feasibility of delineating and identifying mineral ores from hyperspectral images of tin-tungsten mine excavation faces using machine-learning classification. We compiled a set of hand samples of minerals of interest from a tin-tungsten mine and analyzed two types of hyperspectral images: 1) images acquired with a laboratory set-up under close-to-optimal conditions; and 2) scan of a simulated mine face using a field set-up, under conditions closer to those in the gallery. We have analyzed the following minerals: cassiterite (tin ore), wolframite (tungsten ore), chalcopyrite, malachite, muscovite, and quartz. Classification (Linear Discriminant Analysis, Singular Vector Machines and Random Forest) of laboratory spectra had a very high overall accuracy rate (98%), slightly lower if the 450 – 950 nm and 950 – 1780 nm ranges are considered independently, and much lower (74.5%) for simulated conventional RGB imagery. Classification accuracy for the simulation was lower than in the laboratory but still high (85%), likely a consequence of the lower spatial resolution. All three classification methods performed similarly in this case, with Random Forest producing results of slightly higher accuracy. The user’s accuracy for wolframite was 85%, but cassiterite was often confused with wolframite (user’s accuracy: 70%). A lumped ore category achieved 94.9% user’s accuracy. Our study confirms the suitability of hyperspectral imaging to record the spatial distribution of ore mineralization in progressing tungsten-tin mine faces.

There is a considerable increase in the use of substances and medical procedures aimed at changing the esthetics of the face, particularly the appearance of the lips. Permanent fillers such as polydimethylsiloxane, also called liquid silicone, are widely used, but their application for facial esthetics is currently obsolete. However, the long-term complications remain a reality, as they can occur decades after the application. Thus, the goal of this case report was to present a complication after 16 years of treatment using liquid silicone. This case report involved a 52-year-old male with a complication of bilateral permanent filler in the upper lip performed 16 years ago, its surgical removal, and histological analysis. Histologically, it was possible to identify a chronic inflammatory, lymphoplasmacytic, and granulomatous reaction, with foreign body giant cells’ reaction, in relation to non-polarizable exogenous material due to the reaction to silicone. The most common complications are granulomas' appearance and material displacement. The case report shows these granulomas are characterized as chronic low-caliber inflammation around the silicone. They have an unknown etiology but are probably multifactorial, from continuous trauma, friction or irritation, iatrogenic factors, infection, immunological mechanisms, and genetic and molecular variations, and can be highly related to the impurity of the injected material.

Silicone rubber formulations in the form of thin discs have been studied under room ambient conditions for their surface characteristics. The samples were silicone rubber manufactured in laboratory and those industrially manufactured. The measurements were done using an electrometer high resistance meter, applying dc voltage under normal room ambient conditions. The results show that the silicone rubber samples show higher values of surface resistivity when the dc voltage was applied. Silicone rubber samples manufactured in laboratory seem to exhibit erratic behaviour unlike their corresponding silicone rubbers manufactured in industry; this could be due to manufacturing shortcomings in laboratory and the irregularities in the way the silicone rubber adhered to the concentric ring electrodes. The empirical current traversing the surface of the silicone rubbers does not decay exponentially but rather it decays as an exponential power of the energization time.

In this work the effect of recycled concrete aggregate modified with mineral admixtures and Nano-silica on the mechanical properties and performance of the concrete was investigated after curing in tap water for 28 and 90 days. The compressive, ƒc, indirect tensile, ƒt, and flexural, ƒb, strengths for cured concrete specimens were measured and concrete strength ratios were analyzed. The water and rapid chloride permeability were measured. SEM analysis of microstructure was, also, investigated. The coarse aggregates used were dolomite (control) and recycled concrete aggregate with the incorporation of different mineral admixtures including ground granulated blast slag and granite as well as Nano-silica. It was found that, the slump values of the dolomite concrete decreases compared with recycle aggregate concrete. The results indicate that, the concrete mix containing recycle aggregate have the highest compressive strength, tensile strength and flexural strength compered to concrete mix containing dolomite aggregate. As far as the compressive strength is concerned, the addition 1 % NS and 15 % of slag improved the physico-mechanical properties of the recycled aggregate concretes compared to the other mixes after curing in tap water.

The aim of this study was to assess the effects of supplementation of inorganic sources of manganese (MnO, MnSO4), zinc (ZnO, ZnSO4) and copper (CuSO4) at different levels (0.06%DM for Mn, 0.05%DM for Zn; and 0.01 and 0.05%DM for Cu) on in vitro rumen fermentation, solubility and bioavailability. Fermentation activity was measured by total gas production (TGP) and dry matter degradability after 70hrs of fermentation (dDM%). Trace-mineral (TM) solubility was estimated by the TM concentration in the supernatant of the final fermentation medium (SOL) and TM bioavailability by the TM concentration in a bacterial enriched fraction (BACT). Mn (regardless of source) and ZnO tended (p&lt;0.10) to decrease, while Cu showed no significant effect on TGP. The addition of inorganic Mn and of ZnO tended (p&lt;0.10) to decrease, ZnSO4 tended to increase (p&lt;0.10), whilst Cu showed no effect on dDM%. Concerning solubility, Mn (MnO and MnSO4), ZnSO4 and CuSO4 significantly (p&lt;0.05, p&lt;0.001 and p&lt;0.01) increased, while ZnO did not affect TM content of the SOL. These results indicate that MnSO4, ZnSO4 and CuSO4 are highly soluble, MnO is quite soluble, while ZnO has a low solubility in the rumen. Based on the TM content of BACT, MnO, MnS4 and CuSO4 have a high bioavailability, while ZnO is poorly assimilated by rumen bacteria. However, the lack of clear inhibition or improvement of fermentations suggests that the rumen microbiota has low requirement for TM supplementation.

Italian Directives recommends the good quality of natural mineral waters but literature data assert a potential risk from several microorganisms colonizing wellsprings and mineral water bottling plants. Aim of study is the identification of microorganisms from spring waters (SW) and bottled mineral waters (BMW) samples. Methods: Routine microbiological indicators, Legionella spp., Nontuberculous mycobacteria (NTM), protozoa (FLA) and physical-chemical parameters were assessed in 24 SW and 10 BMW samples performing culture methods and molecular tests as PCR and qPCR. Results: In 33 out of 34 samples no cultivable bacteria were isolated with the exception of 83 CFU/L of Mycobacterium gilvum, detected in one warm rich-mineralized SW. qPCR showed the presence of Legionella genomic units in 24% of samples (mean 2,9x10²±1,7x10² GU/L) and NTM genomic units in 18% of samples (mean 5,7x10^3±4,1x10³ GU/L). Vermamoeba vermiformis and Acanthamoeba polyphaga were recovered respectively in 70% of BMW samples (counts from 1,3x10³ to 1,2x10⁵) and 42% of SW samples (counts from 1,1x10³ to 1,3x10⁴). Vahlkampfia spp. was detected in 42% of SW and 70% of BMW samples (mean 1,3x10⁴ ±2,9x10³ GU/L). Conclusion: The study highlights a low rate of microbial risk and the importance of risk assessment in natural mineral waters.

The mechanism of the mechanically assisted mineral carbonation of commercial olivine under flow of CO2/N2 mixture has been elucidated by ex situ powder X-ray diffraction and Fourier-transform infrared spectroscopy. The overall CO2 conversion depends to the rotation frequency of the mill’s engine, and reached 85% within 90 minutes of mechanical treatment, at a flow rate of 2.5 l min-1. By tuning the frequency rotation, the kinetics of CO2 conversion changed from a sigmoid behaviour into a more complex reaction pathway, involving subsequent steps. The structural analyses suggest the clinochlore, a Mg- and Fe- containing aluminosilicate gathered among the components of olivine, is formed and consumed in different stages, thus promoting the CO2 sequestration that eventually results into the formation of hydrated and anhydrous Mg-based carbonates.

The basis of modern teeth whitening systems is the use of a whitening gel, usually containing hydrogen peroxide or carbamide peroxide. The purpose of our study was to evaluate the effect of chemical and modified office teeth whitening systems on the mineral metabolism of oral fluid and to determine a safer method. The study covered 81 patients aged 22 to 35 years of both sexes with teeth color A2 and darker on the Vita Classic scale. Determination of the concentration of calcium and phosphates in the oral fluid was carried out on a spectrophotometer using ready-made Human kits. Chemical tooth whitening was performed using a gel based on 40% hydrogen peroxide. After the procedure, remineralization therapy with enamel-sealing liquid was performed for 14 days. The obtained results indicate that the most pronounced changes in the content of calcium (+74.4%, p &lt;0.001) and рhosphates (phosphorus) (-23.07%, p &lt;0.001) were observed when using a chemical bleaching system. After the teeth whitening procedure using a modified technique, less pronounced changes in the concentrations of calcium (+29.07, p &lt;0.001) and phosphorus (-14%, p &lt;0.001) were observed. The use of remineralizing agents led to a faster recovery of the initial levels of calcium and phosphates in the oral fluid. Both bleaching systems caused similar changes in the chemical composition of the oral fluid.

Cadmium, an environmental toxin, is associated with a range of adverse health effects due to increased Reactive Oxygen Species production, including decreased bone mineral density and osteoporosis. Notably, cadmium is found at concentrations 4-5x higher in the blood of smokers versus non-smokers. Experiments performed in human cancer cells indicate that melatonin may directly protect against cadmium-induced tissue damage via regulation of mitochondrial activity. Further, recent evidence has demonstrated that melatonin can improve bone health for individuals with osteoporosis and partially protect against cadmium-associated inhibition of bone repair. Here we review this data and propose supplementation with melatonin as a strategy to protect against the negative impacts of cadmium exposure on bone mineral density within individuals regularly exposed to cadmium via cigarette smoking.

A major problem in the post-inversion geophysical interpretation is the extraction of geological information from inverted physical property models, which do not necessarily represent all underlying geological features. No matter how accurate the inversions are, each inverted physical property model is sensitive to limited aspects of subsurface geology and is insensitive to other geological features that are otherwise detectable with complementary physical property models. Therefore, specific parts of the geological model can be reconstructed from different physical property models. To show how this reconstruction works, we simulated a complex geological system that comprises an original layered earth model that has passed several geological deformations and alteration overprints. Linear combination of complex geological features comprised three physical property distributions: Electrical resistivity, induced polarization chargeability, and magnetic susceptibility models. This study proposes a multivariate feature extraction approach to extract information about the underlying geological features comprising the bulk physical properties. We evaluated our method in numerical simulations and compared three feature extraction algorithms to see the tolerance of each method to the geological artifacts and noises. We show that the fast-independent component analysis (fast-ICA) algorithm by negentropy maximization is a robust method in the geological feature extraction that can handle the added unknown geological noises. The post-inversion physical properties are also used to reconstruct the underlying geological sources. We show that the sharpness of the inverted images is an important constraint on the feature extraction process. Our method successfully separates geological features in multiple 3D physical property models. This methodology is reproducible for any number of lithologies and physical property combinations and can recover the latent geological features, including the background geological patterns from overprints of chemical alteration.

From 1964 to the early 1970s, Orson Anderson led a research program at the Lamont Geological Observatory in the newly-emerging field of “mineral physics”. In collaboration with colleagues Edward Schreiber and Naohiro Soga, Orson exploited the techniques of physical acoustics to study the behavior of the sound velocities of minerals at elevated pressures and temperatures. This research program also included semi-empirical studies of relationships between the bulk modulus and the molar volume of solids and the use of lattice dynamics to calculate the elastic moduli of cubic structures as a function of pressure to predict instabilities, as well as theoretical investigations of the Lagrangian vs. Eulerian formulations of finite strain equations of state.

Penile augmentation using filler injections is a growing trend; however, the foreign body reaction can cause complications such as ulcer and necrosis of the penis, which can requires reconstruction. The existing method of reconstruction of the penis focused on filling the deficit. We report a case involving a scrotal flap and autologous augmentation using a de-epithelialization technique for a soft tissue defect caused by delayed infection after a penile filler injection. The defect was reconstructed and an augmentation effect was achieved. The patient was a 41-year-old man who received an injection of Aquafilling® (Biomedica, Prague, Czech Republic) 7 years previously and developed a delayed infection. After debridement, the penile defect spanned the entire shaft, and the circumference of the penis was 7.5 cm. Using a bilateral scrotal flap technique, the inferior margins of both flaps were rolled inward after de-epithelialization to achieve autologous augmentation. No infection or flap necrosis occurred during the 3-month follow-up period after surgery. Additionally, the penis circumference was expanded to 12 cm, and the patient indicated that he was very satisfied with the result. This surgical technique can be widely applied as treatment for penile defects.

This study focused on hydrolysis of cosmetic fillers hyaluronic acid (HA) and kinetics of the HA hydrolysis using the homogenate of the red king crab hepatopancreas. Turbidimetric analysis of the reaction mixture revealed a bell-shaped time dependence of aggregation formation. It was shown that the obtained homogenate has the similar activity to the commercially available hyaluronidase. The atomic force microscopy (AFM) examination found that the HA fillers were represented by spherical-like structures. These structures were destroyed under the action of the homogenate of the red king crab hepatopancreas. NMR of the reaction mixture showed that HA degradation lasts for some days, but a maximum rate of the reaction is detected in the first hours of incubation. The preparation with hyaluronidase activity obtained from the red king crab hepatopancreas could be used as potentially safe product for treating filler complications.

An innovative concrete that incorporates the advantages of self-compacting concrete with geopolymer is called self-compacting geopolymer concrete. The objective of this study was the Manufacturing of M30-grade self-compacting geopolymer concrete by adding industrial materials like fly ash (FA), ultrafine ground granulated blast furnace slag (UFGGBS), and silica fume (SF) as minerals. The disposal of these industrial wastes can be substantially overcome, as they lead to land pollution. The fixed powder content was 500 kg/m³. A mixture of sodium silicate (Na₂SiO₃) and sodium hydroxide (NaOH) created an alkaline solution that activated the cementitious binders. In this study, slump flow, L-box, V Funnel, T50 V Funnel, and J ring tests were carried out to determine the fresh qualities of the concrete. These tests were conducted under the regulations for self-compacting concrete provided by EFNARC (2005). To improve the flexural strength of the SCGC, 1.5 % glass fibre was added. This study illustrates how an artificial neural network (ANN) model can determine the concrete mix proportion. The characteristics of SCGC, both fresh and hardened properties test were investigated for molarities of 8, 10, and 12. The microstructural outcomes were determined using Fourier-transform infrared spectroscopy (FT-IR), scanning electron microscopy (SEM), and X-ray diffraction (XRD).

Scanning electron microscopy (SEM) is a powerful tool in the domain of material science, mining, and geology, owing to its enormous potential to provide unique insights into the micro and nanoscale worlds. This comprehensive review discusses the background development of SEM, basic SEM operation including the specimen preparation and imaging process, and fundamental theoretical calculations underlying the SEM operation. It provides foundational understanding to the engineers and scientists, who never got a chance to dig in-depth into the SEM, to understand the working and development of this robust analytical technique. The present review covers how SEM has been serving as a crucial tool in mineral characterization, with specific discussions on the working and research fronts of SEM-EDX, SEM-AM, SEM-MLA, and QEMSCAN. With automation gaining pace in the development of all spheres of technology, the understanding of uncertainties in SEM measurements is very important. The constraints in mineral phase identification by EDS spectra and sample preparation are conferred. In the end, future research directions for SEM are analyzed with the possible incorporation of machine learning, deep learning, and artificial intelligence tools, for automating the process of mineral identification, quantification, and efficient communication with the researchers, so that the analytical process robustness and objectivity can be improved, and the analysis time and the involved costs can be brought down. This review also discusses the idea of integrating robotics with SEM, to make the equipment portable, so that further mineral characterization insights can be gained not only on earth but also on other terrestrial grounds.

The causal effects of chondroitin, glucosamine, and vitamin/mineral supplement intake on kidney function remain unknown, despite being commonly used. We conducted a two-sample summary-level Mendelian randomization (MR) analysis to test for causal associations between regular dietary supplement intake and kidney function. Genetic instruments for chondroitin, glucosamine, and vitamin/mineral supplement intake were obtained from genome-wide association study of European ancestry. Summary statistics for the log-transformed estimated glomerular filtration rate (log-eGFR) were provided by the CKDGen consortium. The multiplicative random-effects inverse variance-weighted method showed that genetically predicted chondroitin and glucosamine intake was causally associated with a lower eGFR (chondroitin, eGFR change beta = -0.113 %, standard error (SE) = 0.03 %, P-value = 2E-04; glucosamine, eGFR change beta = -0.240 %, SE = 0.035 %, P-value = 6E-12). However, a genetically predicted vitamin/mineral supplement intake was associated with a higher eGFR (eGFR change beta = 1.426 %, SE = 0.136 %, P-value = 1E-25). Validation analyses and pleiotropy-robust MR results for chondroitin and vitamin/mineral supplement intake supported the main results. Our MR study suggests a potential causal effect of chondroitin and glucosamine intake on kidney function. Therefore, clinicians should carefully monitor their long-term effects.

Cu₆Sn₅ whiskers precipitated in Sn3.0Ag0.5Cu/Cu interconnection in concentrator silicon solar cells solder layer were found and investigated after reflow soldering and during aging. Ag₃Sn fibers can be observed around Cu₆Sn₅ whiskers in the matrix microstructure, which can play an active effect on the reliability of interconnection. Different morphologies of Cu₆Sn₅ whiskers can be observed, and hexagonal rod structure is the main morphology of Cu₆Sn₅ whiskers. A hollow structure can be observed in hexagonal Cu₆Sn₅ whiskers, and a screw dislocation mechanism was used to represent the Cu₆Sn₅ growth. Based on mechanical property testing and finite element simulation, Cu₆Sn₅ whiskers were regarded as having a negative effect on the durability of Sn3.0Ag0.5Cu/Cu interconnection in concentrator silicon solar cells solder layer.

Nitrogen fertilization ensures the proper growth of trees. The aim of the study was to evaluate the impact of differentiated nitrogen fertilization on selected parameters. It was assumed that such analysis is an indirect picture of the needs of cherries grown in herbicide fallow. The content of minerals in two layers of the soil, in leaves, and its influence of tree growth, and the content of chlorophyll in leaves were assessed. The experiments were carried out in three different cherry orchards. Three levels of fertilization were applied in each orchard: 0 kg, 60 kg and with 120 kg N ha- 1. As expected the fertilization resulted in an increase in the content of nitrate and ammonium forms of nitrogen in the soil, however, their content was also dependent on precipitation and temperature. Additionally a high nitrogen fertilization increased the content of phosphorus and potassium and decreased the magnesium in the topsoil layer. High nitrogen fertilization caused the decrease of content of phosphorus and potassium in the leaves. The level of calcium and magnesium in leaves increased with fertilization of 60 kg N ha–1 but decreased with the dose to 120 kg N ha–1. The use of nitrogen fertilization increased the vegetative growth of trees measured by leaf area and trunk cross-sectional area. However, the chlorophyll content was not dependent on the amount of nitrogen fertilization.

For the first time, it is shown that inhaled ambient air-dust particles settled in the human lower respiratory tract induce lung calcification. Chemical- and mineral compositions of pulmonary calcium precipitates in the lung right lower-lobe (RLL) tissues of 12 individuals who lived in Upper Silesia Conurbation in Poland and who had died from causes not related to lung disorder were determined by transmission- and scanning electron microscopy. Whereas calcium salts in lungs are usually reported as phosphates, calcium salts precipitated in RLL are almost exclusively carbonates, i.e. Mg-calcite and calcite. These constitute 37% of 1652 mineral particles examined. Mg-calcite predominates in the submicron size range with the MgCO3 content up to 50 mol%. Magnesium plays a significant role in the lung mineralization, a fact so far overlooked. The calcium phosphate (hydroxyapatite) content in RLL is negligible. The predominance of carbonates is explained by increased CO2 fugacity in RLL. Carbonates enveloped inhaled mineral-dust particles, including uranium-bearing oxides, quartz, aluminosilicates, and metal sulfides. Three possible pathways for the carbonates precipitation on the dust particles are postulated: (1) precipitation of amorphous calcium carbonate (ACC) followed by its transformation to calcite; (2) precipitation of Mg-ACC followed by its transformation to Mg-calcite; (3) precipitation of Mg-free ACC causing a localized relative enrichment in Mg ions and subsequent heterogeneous nucleation and crystal growth of Mg-calcite. The actual number of inhaled dust particles may be significantly greater than observed because of the masking effect of the carbonate coatings. There is no simple correlation between smoking habit and lung calcification.

Aiming at the industrial scale development of a Scandium (Sc)-selective leaching process of Bauxite Residue (BR), a sufficiently numerous set of process design aspects has been investigated, by appropriate exploitation of available experimental data. The interpretation of experimental data for Sc leaching yield, with sulfuric acid as the leaching solvent, has shown significant impact from acid feed concentration, mixing residence time, liquid to solids ratio, and times of leachate re-usage onto fresh BR. The thin film diffusion model, as the fundamental theory for leaching, either with constant particle size for selective leaching, or with shrinking particle size for less-, or non-, selective leaching, interprets sufficiently well the relevant experimental data. In both cases, a concept for an unyielding core supplements the basic model. Especially for the selective leaching mild conditions, the simplest model version keeps step with the experiments, since both prove 1^st order kinetics, while especially for the extreme conditions including very low solvent excess, it is proposed a combined conversion rate model with diffusion and chemical reaction inside particles. The maximization of Sc recovery per unit of consumed solvent (i.e., specific recovery) emerged as highly critical for the process economics.

Synthesis of styrene butadiene hybrid latex was performed via emulsion polymerization technique using various amount of laponite clay as filler. Laponite clay was modified with cationic surfactant methyl triphenylphosphonium bromide (MTPB) with ion exchange technique prior to polymerization process. The main objective of the modification is to render the surface of the clay layers to more organophilic. Emulsion polymerization was performed under semi batch process using 2 L laboratory stainless steel reactor with temperature 85°C to 90°C for 8 hours. Polymer hybrid styrene butadiene latex was characterized for its physical and chemical properties with standard ASTM Methods. Characterization of its binding and printing properties were carried out with standard testing method (TAPPI Methods) using single coating formulation on 80 gsm woodfree paper. Polymer hybrid latex based on styrene and butadiene monomers with laponite clay enhanced binding and printing properties of coated paper, addition of laponite clay to 6.0 wt % increased the binding resistance of the coated paper two times higher than pure latex. Reducing binder level become possible for cost saving.