Steam boiler has a significant role in the industrial sector. The failure in boiler tubes significantly reduces the availability of the plant. Furthermore, deposits on the inner tube wall contribute to such failure by changing the thermal resistance of the wall, which causes a significant increase in the tube wall's temperature and, consequently, lower allowable stress. The presented thermal-fluid model is developed for the water tube. The model is implemented using ANSYS FLUENT to estimate the wall maximum water tube wall temperature considering the deposits layer and then determine the minimum thickness of the tube wall via ASME standards to assure safe operation. The model is verified via a mesh independence test. The minimum tube thickness is recommended and justified given the thermo-mechanical performance of the water tubes at several operating loads of 50, 75, and 100 %. These loads are implemented by different convective heat transfer coefficients of flue gases under different deposit thicknesses, thermal conductivity, and flue gas temperature. The present work contributes to the literature by recommending the minimum thickness of the water wall tubes and highlighting the thermo-mechanical effect of the deposits on water tube resilience under different operating conditions.

Minimum Inhibitory Concentration (MIC) measures the lowest concentration of antibiotic that inhibits in-vitro growth of microorganisms. Canine pyometra is a frequently occurring reproductive disorder where reliable antibiotics along with surgical excision of uterus predicts better prognosis. Scarce literature is available to facilitate proper antibiotic selection to avoid septicemia in clinical cases. The present study was conducted to determine sensitivity and potency of selected antibacterials based on MIC values against bacterial isolates obtained from Canine Pyometra in Kathmandu district, Nepal by Agar Dilution method. Isolates obtained from 63 intra-uterine samples after ovariohysterectomy were Enterococcus spp (n=41), Klebsiella spp. (n=7), Staphylococcus spp. (n=11) and Streptococcus spp. (n=4). Enrofloxacin and Amikacin were found highly sensitive (0% resistance) with a null hypothesis of resistance to all bacterial isolates and were significantly more potent than other antibacterials tested (p<0.05; Kruskal-Wallis test) based on lower MIC ranks. Similarly, ceftriaxone was found to be least potent and was highly resistant to Enterococcus spp. (75.61%) and completely resistant to other bacterial species tested (100%). Comparative results on sensitivity and potency in the study revealed Enrofloxacin and Amikacin to be better antibacterial of choice in pyometra innervation in in-vitro setting. Further clinical trials considering other equally important variables along with MIC should be conducted to predict actual clinical efficacy of antibacterials during therapeutic management of canine pyometra in Nepal.

In this note we study the computation of the minimum polynomial of a matrix $A$ and how we can use it for the computation of the matrix $A^n$. We also describe the form of the elements of the matrix $A^{-n}$ and we will see that it is closely related with the computation of the Drazin generalized inverse of $A$. Next we study the computation of the exponential matrix and finally we give a simple proof of the Leverrier - Faddeev algorithm for the computation of the characteristic polynomial.

The increase in the frequency of droughts in Africa has increased the interest in crops with drought escape mechanisms like grain Amaranth (Amaranthus hypochondriacus). However, the white-seeded grain Amaranth is easily cross-pollinated by its black seeded wild relatives such as smooth pigweed (Amaranthus hybridus). A study to investigate a minimum isolation distance enough to prevent seed contamination study was carried out at three sites namely Gweru and Bindura (2020/2021 rainy season) and Shamva (2021/2022 rainy season). Smooth pigweed was planted at distances of 3 to 150 m from pure grain Amaranth. Close monitoring of phenology and measurement of meteorological conditions such as temperature, wind speed and direction were done during the anthesis period. Cross-pollination in grain Amaranth was influenced by distance from the pollen source. A maximum of 12.9 % contamination rate was measured within the 10 m radius from the pollen donor plot and a minimum outcrossing rate of 0.45 % was recorded at the widest distance of 150 m. It can be concluded that complete removal of wild relatives of grain Amaranth is important within the field at as far as 150 m from the crop.

We propose a quantum version of the well known minimum distance classification model called "Nearest Mean Classifier" (NMC). In this regard, we presented our first results in two previous works. In [34] a quantum counterpart of the NMC for two-dimensional problems was introduced, named "Quantum Nearest Mean Classifier" (QNMC), together with a possible generalization to arbitrary dimensions. In [33] we studied the n-dimensional problem into detail and we showed a new encoding for arbitrary n-feature vectors into density operators. In the present paper, another promising encoding of n-dimensional patterns into density operators is considered, suggested by recent debates on quantum machine learning. Further, we observe a significant property concerning the non-invariance by feature rescaling of our quantum classifier. This fact, which represents a meaningful difference between the NMC and the respective quantum version, allows to introduce a free parameter whose variation provides, in some cases, better classification results for the QNMC. The experimental section is devoted to: i) compare the NMC and QNMC performance on different datasets; ii) study the effects of the non-invariance under uniform rescaling for the QNMC.

The purpose of the present study was to examine the relationships between bat swing speed (BSS) and muscle thickness and lateral asymmetry of the trunk and limbs in collegiate baseball players. Twenty-four collegiate baseball players participated in this study. The maximum BSS in hitting a teed ball was measured using a motion capture system. The muscle thicknesses of the trunk (upper abdominal rectus, central abdominal rectus, lower abdominal rectus, abdominal wall, and multifidus lumborum), upper limb, and lower limb were measured using a B-mode ultrasonography. Lateral asymmetry between each pair of muscles was determined as the ratio of the thickness of the dominant side to that of the non-dominant side. Significant positive correlations were observed between BSS and muscle thicknesses of the abdominal wall and multifidus lumborum on the dominant side (r = 0.426 and 0.431, respectively; p < 0.05), while nearly significant positive correlations were observed between BSS and muscle thicknesses on the non-dominant side. No significant correlations were found between BSS and lateral asymmetry of all muscles. These findings indicate the importance of the trunk muscles for bat swing, and the lack of association between BSS and lateral asymmetry of muscle size.

We aimed to determine whether A-mode ultrasound (US) can provide accurate and reliable measurements comparable to those obtained through B-mode US, under diverse conditions. Thirty healthy participants (15 female, 15 male) underwent measurements of subcutaneous fat thickness (SFT), muscle thickness (MT), and muscle quality (MQ) in the trapezius and biceps brachii muscle with both US modes after and before exercises designed to stimulate the respec-tive muscles. In three key indices, the results demonstrated high validity of A-mode, with min-imal mean differences between the two devices less than 0.91mm and intraclass correlation coef-ficients exceeding 0.95 at all measures. Also, Correlation coefficients between error scores and average scores for the trapezius and biceps brachii muscles suggested no evidence of systematic error. The trapezius MT and MQ significantly increased, and biceps brachii MT significantly in-creased after exercise (p<0.05). Notably, both A-mode and B-mode exhibited the same tendency in these post-exercise changes in muscle. This study suggests that low-cost and low-resolution A-mode US provides measurements of SFT, MT, and MQ similar to more expensive, high-resolution B-mode imaging. A-mode US can serve as an affordable and portable alternative for muscle assessment.

The purpose of this finite element analysis (FEA) was to evaluate the stress experienced by both the prosthetic components and the bone in relation to varying cement thicknesses ranging from 20 to 60 μm, utilized in the attachment of a zirconia crown on a conometric cap. The study focused on two distinct types of implants (Cyroth and TAC, AoN Implants, Grisignano di Zocco, Italy) featuring a Morse cone connection. Detailed three-dimensional (3D) models were created to repre-sent the bone structure (cortical and trabecular) and the prosthetic components, encompassing the crown, cement, cap, abutment, and the implant. The two implants were placed in a 1.5 mm sub-crestal position and subjected to an inclined load of 200 N at 45° on the crown. The results re-vealed that an increase in cement thickness resulted in a reduction of von Mises stress on the cor-tical bone for both Cyroth and TAC implants, while the decrease in stress on the trabecular bone was relatively less pronounced. However, the TAC implant exhibited a higher stress field and de-formation in the apical area compared to the Cyroth implant. In summary, this study investigated the impact of cement thickness on stress transmission across prosthetic components and peri-implant tissues by means of FEA analysis, indicating that the 60 μm cement layer manifested higher stress values nearing the material strength limit.

The Randić index of a graph G is the sum of (dG(u)dG(v))−1/2 over all edges uv of G, where dG(u) denotes the degree of vertex u in G. In this paper, we investigate a few graph transformations that decrease Randić index of graph. By applying those transformations, we determine the minimum Randić index on tricyclic graphs, and characterize the corresponding extremal graphs.

Modular steel buildings (MSBs) interlocking inter-module connections (IMCs) have piqued researchers’ interest. However, the existing literature has not yet studied the optimisation of its plate thicknesses. This paper, therefore, focuses on optimising interlocking (IMCs) plate thickness in (MSBs), leveraging previous experimental and numerical simulation methodologies. Various numerical models for four MSBs interlocking (IMCs) with plate thicknesses (4 mm, 6 mm, 10 mm, and 12 mm) were developed under compression loading conditions. The study’s novelty lay in its comprehensive parametric analysis, which evaluated the slip phenomenon in (MSBs) connections and introduced a slip prediction model validated against empirical data. Further innovative machine learning approach was utilised to predict slip values based on applied force through a random forest regression model trained using the 'Treebagger' function. Sensitivity analysis and comparisons with alternative methods were utilised to underscore the reliability and applicability of the findings. The results showed that 11.03 mm was the optimal plate thickness for interlocking (IMCs) in modular steel buildings, with up to 8.08% reduced material costs. Increasing plate thickness boosts its deformation resistance by up to 50.75%. ‘TreeBagger’ random forest for anomaly detection and machine learning improves slip prediction up to 7% at higher force levels.

We investigate the power of time series analysis based on a variety of information-theoretic approaches from statistics (AIC, BIC) and machine learning (Minimum Message Length) - and we then compare their efficacy with traditional time series model and with hybrids involving deep learning. More specifically, we develop AIC, BIC and Minimum Message Length (MML) ARMA (autoregressive moving average) time series models - with this Bayesian information-theoretic MML ARMA modelling already being new work. We then study deep learning based algorithms in time series forecasting, using Long Short Term Memory (LSTM), and we then combine this with the ARMA modelling to produce a hybrid ARMA-LSTM prediction. Part of the purpose of the use of LSTM is to seek capture any hidden information in the residuals left from the traditional ARMA model. We show that MML not only outperforms earlier statistical approaches to ARMA modelling, but we further show that the hybrid MML ARMA-LSTM models outperform both ARMA models and LSTM models.

Background: Bayesian Network (BN) modeling is a prominent methodology in computational systems biology. However, the incommensurability of datasets fre- quently encountered in life science domains gives rise to contextual dependence and numerical irregularities in the behavior of model selection criteria (such as MDL, Minimum Description Length) used in BN reconstruction. This renders model features, first and foremost dependency strengths, incomparable and diffi- cult to interpret. In this study, we derive and evaluate a model selection principle that addresses these problems. Results: The objective of the study is attained by (i) approaching model eval- uation as a classification problem, (ii) estimating the effect that sampling error has on the satisfiability of conditional independence criterion, as reflected by Mutual Information, and (iii) utilizing this error estimate to penalize uncertainty with the novel Minimum Uncertainty (MU) model selection principle. We vali- date our findings numerically and demonstrate the performance advantages of the MU criterion. Finally, we illustrate the advantages of the new model evaluation framework on real data examples. Conclusions: The new BN model selection principle successfully overcomes per- formance irregularities observed with MDL, offers a superior average convergence rate in BN reconstruction, and improves the interpretability and universality of resulting BNs, thus enabling direct inter-BN comparisons and evaluations.

In pediatric burn care, achieving swift healing with minimal complications remains paramount. This investigation assesses polyhexamethylene biguanide (PHMB)'s role in managing superficial partial-thickness burns in children, focusing on the effects of various patient-specific factors on recovery. Through a retrospective analysis of 27 pediatric cases treated with PHMB, we explored the impact of age, burn size, dressing frequency, treatment delay, cold therapy application, and analgesic usage on the duration until reepithelialization. Notably, the majority of patients benefited from early cold therapy, yet only 1 in 3 patients received analgesics. The study reveals a mean healing time of 8.78 days, with the extent of the burn showing a strong correlation to recovery speed. Most treatments were managed outpatient, evidenced by a negligible average hospital stay. Impressively, the intervention recorded no complications. Our findings endorse PHMB as a promising treatment for second-degree burns in young patients, offering healing efficiency on par with or surpassing traditional methods, without increasing complication risks. This investigation underscores the necessity for continued exploration into the optimal application of prehospital interventions and the comprehensive benefits of PHMB in pediatric burn management, advocating for future research aimed at assessing long-term outcomes, including scar quality and patient satisfaction.

An effort was made to find a relationship between the ratio of average asperities height and lubricant thickness at the point of contact of rolling element ball bearings, and empirical equations to predict the life for bearings under constant motion. Two independent failure mechanisms were considered, fatigue failure and lubricant failure resulting in seizing of the roller bearing. A theoretical formula for both of these methods was established for the combined probability of failure using both of these failure mechanisms. Fatigue failure was modeled with the empirical equations of Lundberg and Palmgren and standardized in DIN/ISO281. The seizure failure, which this effort sought to investigate, was predicted using Greenwood and Williamson's theories on surface roughness and asperities during lubricated contact. These two mechanisms were combined, and compared to predicted cycle lives of commercial roller bearing, and a clear correlation was demonstrated. This effort demonstrated that the Greenwood-Williams theories on the relative height of asperities versus lubricant film thickness can be used to predict the probability of a lubricant failure resulting in a roller bearing seizing during use.

An effort was made to find a relationship between the predicted tribological conditions at the point of contact of ball bearings, and empirical equations to predict the life for bearings under constant motion. The model was modified to predict the temperature dependence, and compare rapid accelerations and decelerations with empirical extrapolations.

Background/Objectives: Patients with chronic kidney disease (CKD) have an increased risk of cardiovascular disease (CVD). Carotid intima-media thickness (C-IMT) is a non-invasive marker of atherosclerosis. Low omega-3 polyunsaturated fatty acids (PUFA) intake and vitamin D deficiency are potential cardiometabolic risk factors in patients with CKD. The aim of this study was to evaluate dietary intake and status of omega-3 PUFA and vitamin D in pre-dialysis and hemodialysis patients and to examine the link of dietary α-linolenic acid (ALA) and fish consumption with blood pressure and C-IMT in CKD patients. Methods: All 77 selected patients (36 pre-dialysis, 41 on hemodialysis) underwent standardized clinical, nutritional, and laboratory assessments. Repeated 24-hour recalls were performed to assess dietary intake. The fatty acid profile was determined by gas-liquid chromatography. Results: Inadequate vitamin D intake and vitamin D status were found in 95% of patients. PUFAs profiles did not differ between hemodialysis and pre-dialysis participants. Dietary intake of ALA was negatively correlated with systolic blood pressure (SBP) (p=0.007), C-IMT (p=0.002), serum CRP (p=0.044), iPTH (p=0.01) and 25(OH)D3 (p=0.006). ALA intake of more than 0.23 g/daily was associated with lower SBP (p=0.001), serum 25(OH)D3 (p=0.004), and C-IMT (p=0.002). Conclusions: This study contributes to a better understanding of the relationship between dietary ALA intake and C-IMT in CKD. The results of this study could emphasize the significant role of the high prevalence of vitamin D deficiency and inadequate omega-3 PUFA intake and status considering CVD health in CKD patients.

Minimum housing standards aim to safeguard housing rights and enhance residential conditions. Governments develop housing policies, including provision, preservation, and support for welfare programs, guided by the status of households below these standards. Growing nations commonly utilize this approach to decrease the proportion of households not meeting these criteria. In South Korea, the ratio of households below these standards was 4.5% in 2021, down from 16.6% in 2006, as indicated by the initial Korea Housing Survey. However, this downward trend has stalled over the past decade. With the 2004 and 2011 revisions, the standards have been effective for 12 years, yet no longer mirror current housing realities due to ongoing improvements. This study aimed to propose enhancements to Korea’s minimum housing standards. Through analyzing laws, prior research, present household statuses, international cases, and expert insights, recommendations emerged. Categorizing households by size, we developed precise standards covering area, facility, and location aspects. These new standards led to an 8.4% non-compliance rate in 2021. This research’s findings anticipate aiding the revision of minimum housing standards, formulating pragmatic policies for enhancing residential conditions in line with present situations.

A three-dimensional vector field model is proposed, whose dimensions are the Hansen Solubility Parameters: dispersion parameter (δD), polarity parameter (δP), and hydrogen bonding parameter (δH). The vector space that defines the field has the peculiarity of having the dispersion vector with a magnitude of 2, as its base vector, while polarity and hydrogen bonding vectors have a magnitude of 1. A substance is characterised as a position vector, and the interaction between two substances is determined by calculating the vector difference of both, known as the interaction vector. Interaction among substances may involve solubility, swelling, cracking, surface tension, interface tension, and any physical phenomena where intermolecular energies of dispersion, polarity or hydrogen bonding come into play. This paper studies free surface energy (surface and interfacial tension). It has been found that free surface energy is directly proportional to the square of the magnitude of the interaction vector. The proportionality constant, τ, is expressed in length units, has a value of 0.025 nm, and does not depend on the chemical nature of the substance or state of matter (solid, liquid or gas). Constant value τ appears universal and aligns with the thickness of interfaces, thereby supporting Guggenheim's hypothesis. This hypothesis asserts that interfaces possess actual thickness and are not merely mathematical surfaces, as originally postulated by Gibbs. Moreover, it also has been found that interface thickness, τ, is approximately equal to half of the Bohr radius, a0, which is defined by universal constants. Because the solubility parameters of thousands of substances are known and can be easily determined from molecular structure, a good approximation of the surface and interfacial tension of any given substance can now be calculated. It has also been found that contact angles of sessile droplets in three-phased systems can be calculated from the interaction vectors of the implicated substances.

Introduction: Migraine is one of the most prominent headache disorders with a global burden of over one billion patients and presented as a disabling and painful disorder. Pathophysiological mechanism of migraine is not fully understood, but the most accepted theory suggests that migraine is caused primarily by neural dysfunction leading to secondary changes in cerebral perfusion. Methods: Authors conducted a case-control study in 175 patients; 88 of them were migraineurs and 87 health controls. Optical coherence tomography (OCT) was performed in all patients using spectral-domain OCT device in the same environmental conditions. All participants met both inclusion and exclusion criteria in order to achieve more homogeneous groups. OCT was performed to scan all retinal layers with an emphasis on the inner plexiform layer (IPL). Results: Among 175 examined subjects, 84% of them were women and in the group of migraineurs we found 56% without aura and 44 % with aura. After collecting tomography data authors did not find subjects in which changes of IPL were found. Nevertheless, only moderate differences in the IPL thickness in all quadrants except the central area were found in the group of migraineurs with aura using Pearson’s test. Conclusion: According to presented results, no significant changes of the IPL thickness in migraine patients were found. Authors have to emphasize the need for further investigation of the relationship between average migraine headache days per month and the thickness of the IPL.

A short review of the important studies was conducted to evaluate the potential of aerosol transmission of the Severe Acute Respiratory Syndrome Coronavirus 2 (SARS-CoV-2). The minimum size of droplets potentially carrying the SARS-CoV-2 was newly estimated and discussed in this review.

The design of curved surface sliders (CSS) based on the elastic response spectrum is done by iteration to find the combination of friction coefficient and displacement capacity which satisfies the condition that the maximum horizontal CSS force is equal to the horizontal force of the structure. Although this CSS design is valid it does not necessarily minimize structural acceleration. This paper therefore describes the optimum CSS design for minimum structural acceleration. All valid CSS designs and the optimum CSS design are represented by their associated trajectory in the elastic response spectrum plane which visualizes the optimization problem. The results demonstrate that the optimum CSS design is not obtained at maximum tolerated effective damping ratio. The subsequent sensitivity analysis describes how much the structural acceleration increases if the actual friction coefficient of the real CSS deviates from its optimum design value. The analysis points out that the increase in structural acceleration is approximately one order of magnitude smaller than the deviation in friction. The sensitivity data may be used by structural engineer to determine tolerable deviations in friction coefficient which still results in acceptable structural accelerations.

We show that, as in the case of the principle of minimum action in classical and quantum mechanics, there exists an even more general principle in the very fundamental structure of quantum space-time: This is the principle of minimal group that allows to consistently and simultaneously obtain a natural description of the spacetime dynamics and the physical states admissible in it. The theoretical construction is based on the physical states that are average values of the generators of the Metaplectic group Mp(n) , the double covering of SL(2C) in a vector representation, with respect to the coherent states carrying the spin weight. Our main results here are: (i) There exists a connection between the dynamics given by the Metaplectic group symmetry generators and the physical states (mappings of the generators through bilinear combinations of the basic states). (ii) The ground states are coherent states of the Perelomov-Klauder type defined by the action of the Metaplectic group which divide the Hilbert space into even and odd states mutually orthogonal. They carry a spin weight 1/4 and 3/4 respectively from which, two other basic states can be formed. (iii) The physical states, mapped bilinearly with the basic 1/4 and 3/4 spin weight states, plus their symmetric and antisymmetric combinations, have spin contents s = 0, 1/2, 1, 3/2 and 2. (iv) The generators realized with the bosonic variables of the harmonic oscillator introduce a natural supersymmetry and a superspace whose line element is the geometrical Lagrangian of our model. (v) From the line element as operator level, a coherent physical state of spin 2 can be obtained and naturally related to the metric tensor. (vi) The metric tensor is naturally discretized by taking the discrete series given by the basic states (coherent states) in the n number representation, reaching the classical (continuous) space-time for n going to infinity. (vii) There emerges a relation between the eigenvalue of our coherent state metric solution and the black hole area (entropy) as A_{bh}/4 l_{p}^{2} = I alpha I relating the phase space of the metric found g_{ab} and the black hole area A_{bh} through the Planck length l_{p}^{2} and the eigenvalue I alpha I of the coherent states. As a consequence of the lowest level of the quantum discrete space-time spectrum, eg the ground state associated to n = 0 and its characteristic length, there exists a minimum entropy related to the black hole history.

The minimum dominating tree (MDT) problem consists of finding a minimum weight sub-graph from an undirected graph, such that each vertex not in this sub-graph is adjacent to at least one of the vertices in it, and the sub-graph is connected without any ring structures. This paper presents a Dual Neighborhoods Search (DNS) algorithm for solving the MDT problem, which integrates several distinguishing features, such as two neighborhoods collaboratively working for optimizing the objective function, a fast neighborhood evaluation method to boost the searching effectiveness, and several diversification techniques to help the searching process jump out of the local optimum trap thus obtaining better solutions. DNS improves the previous best-known results for 4 public benchmark instances while providing competitive results for the remaining ones. Several ingredients of DNS are investigated to demonstrate the importance of the proposed ideas and techniques.

Autofocus is an essential part of the SAR imaging process. Multi-subaperture autofocus algorithm is a commonly used autofocus algorithm for processing SAR stripmap mode data. The multi-subaperture autofocus algorithm has two main steps, the first is to estimate the phase error gradient within the subaperture, the second is to splice the phase error gradient, that is, to remove the shift amount between the estimated adjacent subapertures’ error gradients. Previous gradient-splicing algorithms assume that the estimation of subaperture error is accurate, but when the estimation of subaperture phase error gradients is not accurate enough, these algorithm performance will be degraded. A new phase error gradient splicing algorithm is proposed in this paper. It roughly estimates the shift amount first, and then finely estimates the shift amount based on the minimum-entropy criterion, which can improve the robustness of splicing especially when the estimation of the phase error gradients of the subaperture is not accurate enough. To speed up the algorithm, a variable-step-size search method is used. Simulation and experimental results show that the algorithm has enough accuracy and still has good performance when other splicing algorithms doesn’t perform well.

A large variety of molecular interactions occurs between biomolecular components in cells. When one or a cascade of molecular interactions results in a regulatory effect, by one component onto a downstream component, a so-called ‘causal interaction’ takes place. Causal interactions constitute the building blocks in our understanding of larger regulatory networks in cells. These causal interactions and the biological processes they enable (e.g., gene regulation) need to be described with a careful appreciation of molecular interactions that occur between entities. A proper description of this information enables archiving, sharing, and reuse by humans and for computational science. Various representations of causal relationships between biological components are currently used in a variety of resources. Here, we propose a checklist that accommodates current representations, and call it the Minimum Information about a Molecular Interaction CAusal STatement (MI2CAST). This checklist defines both the required core information, as well as a comprehensive set of other contextual details valuable to the end user and relevant for reusing and reproducing causal molecular interaction information. The MI2CAST checklist can be used as reporting guidelines when annotating and curating causal statements, while assuring uniformity and interoperability of the data across resources.

In this paper a robust version of the Wald test statistic for composite likelihood is considered by using the composite minimum density power divergence estimator instead of the composite maximum likelihood estimator. This new family of test statistics will be called Wald-type test statistics. The problem of testing a simple and a composite null hypothesis is considered and the robustness is studied on the basis of a simulation study. Previously, the composite minimum density power divergence estimator is introduced and its asymptotic properties are studied.

The organic solar cells (OSCs) have drawn attention in the past decade due to its cynosure in industrial manufacturing because of its promising properties such as low weight, highly flexible and low cost production. However, low η restricts the utilization of OSCs for potential application such as low cost energy harvesting devices. In this paper, OSCs structure based on triple junction tandem scheme is reported with three different absorber materials with the objective to enhance the absorption of photons which in turn improves the η, as well as its correlating performance parameters. The investigated structure gives the higher value of η = 14.33% with Jsc=16.87 (mA/m2), Voc=1.0 (V), and FF=84.97% by utilizing a stack of three different absorber layers with different band energies. The proposed structure is tested under 1.5 (AM) with 1 sun (W/m2). The impact of top, middle and bottom sub cells thickness on η is analyzed with a terse to find the optimum thickness for three sub cells to extract high η. The optimized structure is then tested with different electrode combination and the highest η is recorded with FTO/Ag. Moreover, the influence of upsurge temperature is also demonstrated on the proposed structure and observed that the upsurge temperature has greatly affected the electrical parameters of the device and η decreases from 14.33% to 11.40% when the temperature of the device rises from 300-400 K.

Being one of the most critical phases of a flight, landing deserves specific attention, especially when the aircraft is subject to external disturbances such as wind. A notable concern associated with touchdown events, especially when crosswind is present is tire wear. This work is aimed first at developing a nonlinear flight simulator able to handle the entire landing maneuver in non-null wind conditions, considering the airborne phase, ground run, and the transition between them. Then, the simulator is included in an optimal process to define the landing technique associated with the minimum tire wear. The methodology is tested in a simulation environment with a realistic model of a reference aircraft, showing that a significant reduction of tire wear can be obtained by optimizing the sideslip angle at touchdown and the lateral-directional controls after the airplane touches the runway with both legs of the main landing gear.

This paper reassesses the detrimental effect on fatigue performance due to thicker sections based on extensive fatigue strength test database, taken from research program worldwide over the past half of a century in offshore oil &amp; gas and renewable industry. The data entries in the database have been evaluated to ensure its data integrity. Statistical analyses on these S-N data are performed with or without the thickness correction at different exposure level to corrosive environment, in order to re-evaluate the suitability of current standards in regard to the thickness effect. The study has concentrated on T-joint, transverse butt welded joint and tubular joint as these are the most commonly used joint types in the offshore wind industry. The analysis indicates general agreement of fatigue strength with the thickness effects in current standard for in air conditions but great conservatism for corrosive environment.

A heat transfer model, has determined millimeter crude oil thicknesses on saltwater at night. Model inputs are calibrated thermographic imagery, weather station data, metrological observations, and crude oil thermal conductivity. Outdoor field-testing was performed at the National Oil Spill Response & Renewable Energy Test Facility (Ohmsett) to determine model accuracy. Alaskan North Slope (ANS), Hoover Offshore Oil Pipeline System Blend (HOOPS), and ROCK crude oils were placed at varying mm depths. A roof-top mounted thermal camera measured the average oil surface temperature for each target and converted to oil spill thickness. The fidelity of the thickness measurements is dependent on the accurate measurement of the atmospheric and weather parameters, sea state, heat transfer constants, crude oil evaporation rates, and calibration and stability of the thermal camera.

The heat and matter transfer during glucose catabolism in living systems and their relation with entropy production are a challenging subject of the classical thermodynamics applied to biology. In this respect, an analogy between mechanics and thermodynamics has been performed via the definition of the entropy density acceleration expressed by the time derivative of the rate of entropy density and related to heat and matter transfer in minimum living systems. Cells are regarded as open thermodynamic systems that exchange heat and matter resulting from irreversible processes with the intercellular environment. Prigogine’s minimum energy dissipation principle is reformulated using the notion of entropy density acceleration applied to glucose catabolism. It is shown that, for out-of-equilibrium states, the calculated entropy density acceleration is finite and negative and approaches as a function of time a zero value at global thermodynamic equilibrium for heat and matter transfer independently of the cell type and the metabolic pathway. These results could be important for a deeper understanding of entropy generation and its correlation with heat transfer in cell biology with special regard to glucose catabolism representing the prototype of irreversible reactions and a crucial metabolic pathway in stem cells and cancer stem cells.

We propose two methods for obtaining estimations on the minimum distance and covering radius of orthogonal arrays. Both methods are based on knowledge about the (feasible) sets of distance distributions of orthogonal arrays with given length, cardinality, factors and strength. New bounds are presented either in analytic form and as products of an ongoing project for computation and investigation of the possible distance distributions of orthogonal arrays with parameters in doable ranges.

This study was to explore the effects of glabridin and gymnemic acid on the structural changes of the choroidal layer as well as the expression of VEGF and CD31 in diabetic rats. The animals were separated into five groups: the control group (C), the diabetic group (DM), the diabetic rats treated with glabridin 40 mg/kg body weight (DM+GB), the diabetic rats treated with gymnemic acid 400 mg/kg body weight (DM+GM), and the diabetic rats treated with glyburide 4 mg/kg body weight (DM+GR). There has been an increase in the thickness of both the choroid layer and the wall of the arteries in the diabetic group. A decrease in vascularity and choroidal neovascularization can be found in DM rats. After eight weeks of experimentation, the choroidal thickness and wall of choroid arteries, as well as the diameter of the lumen of choroid arteries in the DM+GB, DM+GM, and DM+GR groups, had improved. The expression of VEGF and CD31 was lower compared to the DM group. According to the findings of the current research, glabridin and gymnemic acid can improve and reduce the damage to the choroid, which is a factor that can sometimes result in vision loss.

The research field of two dimensional (2D) materials strongly relies on optical microscopy characterization tools to identify atomically thin materials and to determine their number of layers. Moreover, optical microscopy-based techniques also opened the door to study the optical properties of these nanomaterials. We present a comprehensive study of the differential reflectance spectra of 2D semiconducting transition metal dichalcogenides (TMDCs), MoS₂, MoSe₂, WS₂ and WSe₂, with thickness ranging from one layer up to six layers. We analyze the thickness-dependent energy of the different excitonic features, indicating the change in the band structure of the different TMDC materials with the number of layers. Our work provides a route to employ differential reflectance spectroscopy for determining the number of layers of MoS₂, MoSe₂, WS₂ and WSe₂.

We have performed first-principles calculations to study the interfacial exchange coupling and magnetocrystalline anisotropy (MCA) energy in a SmCo₅/Sm₂Co₁₇ multilayer model systems. The phase of SmCo₅ and Sm₂Co₁₇ stacking along (0001) direction are structurally well matched. The atomic structure, including the alignment and the separation between layers, were firstly optimized. Then the non-collinear magnetic structures were calculated to explore the exchange coupling across the interface and the variation of MCA energy. We found that the inter-phase exchange coupling strength, rotating behavior and MCA energy are strongly dependent on the atomic thickness of the SmCo₅ and Sm₂Co₁₇ phase.

Partial Information Decompositions (PIDs) aim to categorize how a set of source variables provide information about a target variable redundantly, uniquely, or synergetically. The original proposal for such an analysis used a lattice-based approach and gained significant attention. However, finding a suitable underlying decomposition measure is still an open research question, even at an arbitrary number of discrete random variables. This work proposes a solution to this case with a non-negative PID that satisfies an inclusion-exclusion relation for any f-information measure. The decomposition is constructed from a pointwise perspective of the target variable to take advantage of the equivalence between the Blackwell and zonogon order in this setting. The zonogons correspond to the Neyman-Pearson region for an indicator variable of one target state and f-information is the expected value of quantifying its boundary. We prove that the decomposition satisfies the axioms of the original decomposition framework and guarantees non-negative partial information results. We highlight that our decomposition behaves differently depending on the used information measure, which can be utilized for different applications. We additionally show how our proposal can be used to obtain a non-negative decomposition of Rényi-information at a transformed inclusion-exclusion relation, and for tracing partial information flows through Markov chains.

Tripping is the largest cause of falls and low swing foot ground clearance during the mid-swing phase, particularly at the critical gait event known as Minimum Foot Clearance (MFC) is the major risk factor for tripping-related falls. Intervention strategies to increase MFC height can be effective if applied in real-time based on feed-forward prediction. The current study investigated the capability of machine learning models to classify the MFC into various categories using toe-off kinematics data. Specifically, three MFC sub-categories (less than 1.5cm, between 1.5-2.0cm and higher than 2.0cm) were predicted applying machine learning approaches. A total of 18,490 swing phase gait cycles’ data were extracted from six healthy young adults, each walking for 5-minutes at a constant speed of 4km/h on a motorised treadmill. Both K-Nearest Neighbour (KNN) and Random-Forest were utilised for prediction based on the data from toe-off for five consecutive frames (0.025s duration). Foot kinematics data were obtained from inertial measurement unit attached to the mid-foot, recording tri-axial linear accelerations and angular velocities of the local coordinate. KNN and Random-Forest achieved 84% and 86% accuracy, respectively, in classifying MFC into the three sub-categories with run time of 0.39 seconds and 13.98 seconds respectively. The KNN-based model was found to be more effective if incorporated into an active exoskeleton as the intelligent system to control MFC based on the preceding gait event, toe-off due to its quicker computation time. The machine learning based prediction model shows promise for the prediction of critical MFC data indicating higher tripping risk.

Despite the proposal of minimum reporting guidelines for metabolomics over a decade ago, reporting on the data analysis step in metabolomics studies has been shown to be unclear and incomplete. Major omissions and a lack of logical flow render the data analysis’ sections in metabolomics studies impossible to follow, and therefore replicate or even imitate. Here, we propose possible reasons why the original reporting guidelines have had poor adherence and present an approach to improve their uptake. We present in this paper an R markdown reporting template file that guides the production of text and generates workflow diagrams based on user input. This R Markdown template contains, as an example in this instance, a set of minimum information requirements specifically for the data pre-treatment and data analysis section of biomarker discovery metabolomics studies, (gleaned directly from the original proposed guidelines by Goodacre at al.). These minimum requirements are presented in the format of a questionnaire checklist in an R markdown template file. The R Markdown reporting template proposed here can be presented as a starting point to encourage the data analysis section of a metabolomics manuscript to have a more logical presentation and to contain enough information to be understandable and reusable. The idea is that these guidelines would be open to user feedback, modification and updating by the metabolomics community via GitHub.

Minimum miscibility pressure (MMP) and oil swelling are two important factors of carbondioxide (CO₂) gas displacement mechanism occurred in the reservoir relate to application of CO₂ injection in the field to enhance oil recovery. In this paper determination of minimum miscibility pressure (MMP) between crude oil samples with carbondioxide gas conducted using two methods, i.e. correlation methods and laboratory experiment using slimtube. While, determination of swelling factor was conducted using PVT cell, where recombined fluid injected and conditionally at the reservoir temperature. The results of MMP using empirical equation (2807 Psig) and Holm & Josendal correlation (2750 Psig) is more approximate to the result of laboratory analysis (2805 Psig). The result of swelling test during injection CO₂ gas processes until 46.82% mole, shows that bubble point pressure is increasing gradually from 410 psig through 2200 psig, and swelling factor was also increase from 1.0 through 1.442. Based on the value of fracture pressure of Layer F in the KHL Field is 2200 Psig and MMP is 2805 Psig, hence the application of CO₂ gas injection in the field only could be conducted as immiscible flooding.

Reduced nutrient mineralization rates under minimum tillage are usually compensated by mineral fertilizer application. These cannot be applied in organic farming systems, however. We hypothesized that organic minimum tillage based on frequent cover cropping and application of dead mulch will improve soil fertility and can compensate for the potential negative effects of minimum tillage. Two long-term field experiments were set up in 2010 and 2011 comparing plough versus minimum tillage including application of transferred mulch. As second factor, the application of compost versus mineral potassium and phosphorus was compared. In 2019, soils were analyzed for soil pH, organic carbon, macro-, micronutrients, microbial biomass, microbial activity and total nematode abundance. In addition, performance of pea in the same soils was determined under greenhouse conditions. Across both experiments, macronutrients (+52%), micronutrients (+11%), microbial biomass (+51%), microbial activity (+86%), and bacterivorous nematodes (+112%) increased in minimum tillage compared with the plough-based system. In the greenhouse, pea biomass was 45% higher in the soil that had been subjected to minimum tillage compared to the plough. In conclusion, soil fertility can be improved in organic minimum tillage systems by intensive cover cropping and application of dead mulch to levels higher than in a plough-based system.

Introduction: intraocular pressure (IOP) measurement is an essential part glaucoma’s diagnosis and follow-up. Goldmann applanation tonometry (GAT) is the gold standard for IOP measurement but it’s affected by many factors like central corneal thickness (CCT). Racial differences in CCT are reported but the Syrian population was never studied. Research design and methods: 57 subjects with 114 eyes visiting Damascus hospital were examined and 100 eyes were included. IOP was measured using GAT and CCT was measured using OCULUS Pentacam AXL Corneal Topography, demographic data and history of ocular surgery, systemic co-morbidities and history of medications were collected. IOP values were corrected for CCT. Results: 56% were males, the mean age was 48.1. 24% of subjects had hypertension. Males had higher CCT with 557.23± 25.33 compared with 531.34 ± 41.88 for females. There was a moderately positive correlation between CCT and IOP (r=0.232, p-0.02), CCT and IOP values were linearly correlated (ANOVA, p=0.02). Conclusions: This study showed that the correlation between CCT and IOP is present in the Syrian population. Males had a slightly thicker corneas than females and CCT didn’t significantly change with age.

Age-related macular degeneration (AMD) causes visual impairment in individuals >50 years of age. However, no study has investigated AMD using ultra-wide-field swept-source optical co-herence tomography (UWF SS-OCT). We aimed to evaluate central and peripheral choroidal thickness using UWF SS-OCT and compare AMD subtypes. We included 75 eyes of patients with typical AMD (tAMD), 56 with polypoidal choroidal vasculopathy (PCV), 29 with pachychoroid neovasculopathy (PNV), and 12 with retinal angiomatous proliferation (RAP). To compare cho-roidal thicknesses in the central and peripheral choroids, we established subfields of <3 mm, <9 mm, and 9–18 mm from the fovea. PNV patients were significantly younger than those with tAMD (P=0.01). The choroidal thicknesses of PNV were significantly greater than that of tAMD in all subfields (P<0.01) and choroidal thickness significantly correlated with age and axial length in all subfields (P<0.05). Even after adjusting for age and axial length, the choroidal thickness in PNV was significantly greater than that in tAMD (P<0.05). In addition, the ratio of the posterior < 9 mm to peripheral 9–18 mm choroidal thickness in PNV was significantly greater than that in tAMD (P<0.01). A thickened choroid in PNV was more pronounced in the posterior choroid than in the periphery.

Toshiba devised the bladeless fan (or Air Multiplier) concept in 1981. Researchers like James Dyson and Jafari et al. further developed it. Bladeless fans are more energy-efficient, safer due to the hidden blades, easier to clean, and more adjustable than conventional fans. From a performance point of view, bladeless fans are better because they multiply mass flow rate, eliminate buffeting, consume less power, and are quieter. This paper investigates the influence of the airfoil’s outlet slit thickness on the discharge ratio by varying the outlet slit thickness of an Eppler 473 airfoil from 1.2 mm to 2 mm in intervals of 0.2 mm. Results indicated that smaller slits showed higher discharge ratios. The airfoil with a 1.2 mm slit thickness showed a discharge ratio of 18.78, a 24% increase from the discharge ratio of the 2 mm slit. The effect of outlet angle on the pressure drop across the airfoil was also studied. Outlet angles were varied from 16∘ to 26∘ by an interval of 2∘. The airfoil profile with a 24∘ outlet angle showed a maximum pressure difference of 965 Pa between the slit and leading edge. In contrast, the 16∘ outlet angle showed the least pressure difference of 355 Pa. Parameters such as average velocity, turbulent kinetic energy, the standard deviation of velocity and outlet velocity magnitude was used to assess the performance of airfoil profiles used in bladeless fan.

For the electromagnetic eddy current testing, various methods have been proposed for reducing the lift-off error on the measurement of samples. In this paper, instead of eliminating the measurement error caused by the lift-off effect, an algorithm has been proposed to directly measure the lift-off distance between the sensor and non-magnetic conductive plates. The algorithm is based on a sample-independent inductance (SII) feature. That is, under high working frequencies, the inductance is found sensitive to the lift-off distance and independent of the test piece under an optimal single high working frequency (43.87 kHz). Furthermore, the predicted lift-off distance is used for the thickness prediction of the non-magnetic conductive samples using an iterative method. Considering the eddy current skin depth, the thickness prediction is operated under a single lower frequency (0.20 kHz). As the inductance has different sensitivities to the lift-off and thickness, the prediction error of the sample thickness is different from that of the lift-off distance. From the experiments on three different nonmagnetic samples – aluminium, copper, and brass, the maximum prediction error of the lift-off distance and sample thickness is 1.1 mm and 5.42 % respectively at the lift-off of 12.0 mm.

In this paper, the optimal approximation algorithm is proposed to simplify non-linear functions and/or discrete data as piecewise polynomials by using the constrained least squares. In time-sensitive applications or in embedded systems with limited resources, the runtime of the approximate function is as crucial as its accuracy. The proposed algorithm search to find the Optimal Piecewise Polynomial (OPP) with minimum computational cost while ensuring the error below a specified threshold. This was accomplished by using smooth piecewise polynomials with optimal order and number of intervals. The computational cost only depends on polynomial complexity, i.e., the order and the number of intervals at runtime function call. For optimal approximation, computational costs for all the possible combinations of piecewise polynomials were calculated and tabulated as ascending order for the specific target CPU off-line. Each combination was optimized through constrained least squares and random selection method for given sample points. Afterward, whether the approximation error is below the predetermined value is examined. When the error is permissible, the combination is selected as the optimal approximation or the next combination was examined. To verify the performance, several representative functions were examined and analyzed.

The minimum vertex cover (MVC) problem is a canonical NP-hard combinatorial optimization problem, aiming to find a smallest set of vertices such that every edge has at least one endpoint in the set, which has extensive applications in cyber security, scheduling, and monitoring link failures in wireless sensor networks (WSNs). Numerous local search algorithms have been proposed to obtain a “good” vertex cover. However, due to the NP-hard nature, it is challenging to efficiently solve the MVC problem, especially on large graphs. In this paper, we propose an efficient local search algorithm for MVC called TIVC, which is based on two main ideas: A 3-improvements (TI) framework with tiny perturbation, and an edge selection strategy. We conducted experiments on real-world large instances of a massive graph benchmark. Compared with two state-of-the-art MVC algorithms, TIVC shows superior performance in accuracy and possesses a remarkable ability to identify significantly smaller vertex covers on many graphs.

The global financial crisis of 2008, triggered by the collapse of Lehman Brothers, highlighted a banking system that was widely exposed to systemic risk. The minimization of the systemic risk via a close and detailed monitoring of the entire banking network became a priority. This is a complex and demanding task considering the size of the banking systems: in the US and the EU they include more than 10000 institutions. In this paper, we introduce a methodology which identifies a subset of banks that can: a) efficiently represent the behavior of the whole banking system and b) provide, in the case of a failure, a plausible range of the crisis dispersion. The proposed methodology can be used by the regulators as an auxiliary monitoring tool, to identify groups of banks that are potentially in distress and try to swiftly remedy their problems and minimize the propagation of the crisis by restricting contagion. This methodology is based on Graph Theory and more specifically Complex Networks. We termed this setting a “multivariate Threshold – Minimum Dominating Set” (mT–MDS) and it is an extension of the Threshold – Minimum Dominating Set methodology (Gogas e.a., 2016). The method was tested on a dataset of 570 U.S. banks: 429 solvent and 141 failed ones. The variables used to create the networks are: the total interest expense, the total interest income, the tier 1 (core) risk-based capital and the total assets. The empirical results reveal that the proposed methodology can be successfully employed as an auxiliary tool for the efficient supervision of a large banking network.

Recent advance in electric propulsion systems have demonstrated that these engines can be used for for long-duration interplanetary voyages. Constant specific impulse engine described as a thrust-limited engine is an example of this type of engine, processing the ability to operate at a constant level of impulse. The determination of minimum-fuel, planar heliocentric Earth-to-Mars low-thrust trajectories of spacecraft using a constant specific impulse is discussed considering the first-order necessary conditions derived from Lawden’s primer vector theory. The minimum-fuel low-thrust Earth-to-Mars optimization problem is then solved in two-dimensional, heliocentric frame using both indirect and direct methods. In the indirect method, two-point-boundary-value problems are derived to solve boundary value problems for ordinary differential equations. In the direct method, a general-purpose optimal control software called GPOPS-II is adopted to solve these optimal control problems. Numerical examples using two different optimization methods are presented to demonstrate the characteristics of minimum-fuel planar low-thrust trajectories with on-off-on thrust sequences at three chosen flight times and available maximum powers. The results are useful for broad trajectory search in the preliminary phase of mission designs.

There is still an ambiguous opinion on oat regarding its safety for people with celiac disease (CD). Some studies have confirmed different content of oat immunoreactive epitopes in different cultivars while others explain the differences in consequence of cross-contamination with gluten-rich species or as ELISA cross-reactivity of oat homological epitopes with antibodies against wheat gliadin. Our study was based on a two-year mapping of oat immunoreactive epitopes in a set of 132 oat cultivars using the G12-based ELISA kit. Although repeated evaluation confirmed high interannual variability (RSD ≥ 30%) in approximately 2/3 of the cultivars, the permitted gluten content (20 mg kg-1) has not been exceeded except for contaminated cultivar Sirene. The polymorphism of purified avenins determined by SDS-PAGE revealed the occurrence of 2 bands around 30 kDa in oat cultivars with relatively high gluten content (12-16 mg kg-1) except for the cultivar Leo while this pattern occurred only in 50% oat cultivars with low gluten content. Quantification of gluten epitopes on purified avenin unit further revealed the three materials (Mojacar, Maris Oberon, SG-K 16370) with the lowest gluten content and presence of one band at 30 kDa. The band pattern at 30 kDa thus represents a promising breeding marker.

Diversification is an important strategy for managing risk in agricultural systems. Risk analysis can help to support farmers’ diversification strategies, but existing analytical methods are complicated and little used. The minimum regret model helps to fill this gap. It provides a simple, transparent calculation procedure that can be executed with existing spreadsheet software. Regret is an important heuristic in the behavioural sciences and regret-based models are used in finance. The article presents the model with a numerical example. It also presents a framework to compare minimum regret portfolios with two limit cases (maximum utility and minimax regret). A case study illustrates the use of the model and the comparative framework.

In this paper, firstly, some questionable formulas and conceptual oversights of previous reduced sigma set unscented transformation (UT) methods are revised through theoretical analysis. Then the revised UT methods based Kalman filters are used in a GPS/INS tightly-coupled system. The Kalman filter flows are the kind of square-root, since the square-root unscented Kalman filters (SRUKFs) can guarantee the stability of the system. By using the reduced sigma set SRUKFs (which contain simplex sigma set square-root unscented Kalman filter (S-SRUKF), spherical simplex sigma set square-root unscented Kalman filter (SS-SRUKF) and minimum sigma set square-root unscented Kalman filter (M-SRUKF)), the computation cost is greatly saved compared with the standard SRUKF, while the accuracy of the GPS/INS tightly-coupled system still maintained. The structure of the GPS/INS tightly-coupled system is in the form of error state, and the time updates of the state and the state covariance of SRUKFs are directly estimated without using UT, thus the computational time is also greatly saved. The pseudo-satellite is introduced to aid the system when the observation information is deficient, for example, when the GPS signal is deficient in the maneuver environment. By using the pseudo-satellite, the optimal performance of the system is guaranteed. Experiment of unmanned aerial vehicle (UAV) showed that the pseudo-satellite aided mechanism worked well.

Overhead power transmission line icing (PTLI) disasters are one of the most severe dangers to power grid safety. Automatic iced transmission line identification is critical in various fields. However, existing methods primarily focus on the linear characteristics of transmission lines, employing a two-step process involving edge and line detection for PTLI identification. Nonetheless, these traditional methods are often difficult when confronted with challenges such as background noise or variations in illumination, leading to incomplete identification of the target area, missed target regions, or misclassification of background pixels as foreground. We propose a new iced transmission line identification scheme to overcome this limitation. In the initial stage, we integrate the image restoration method with image filter enhancement to restore the image's color information. This combined approach effectively retains valuable information and preserves the original image quality, thereby mitigating noise presented during the image acquisition. Subsequently, in the second stage, we introduce an enhanced multi-threshold algorithm to separate background and target pixels. After image segmentation, we enhance the image and obtain the region of interest (ROI) through connected component labeling modification and mathematical morphology operations, eliminating background regions. Our proposed scheme achieves an accuracy value of 97.72%, a precision value of 96.24%, a recall value of 86.22%, and the specificity value of 99.48% based on the average value of test images. Through object segmentation and location, the proposed method can avoid background interference, effectively solve the problem of transmission line icing identification, and achieve 90% measurement accuracy compared to manual measurement on the collected PTLI dataset.

The purpose of the study was to determine the “retinal thickness deviation” (RTD) in diabetic macular edema (DME) eyes treated with intravitreal therapy and to establish associations be-tween RTD and best-corrected visual acuity (BCVA). We conducted a retrospective study, in-cluding consecutive DME eyes undergoing intravitreal therapy with two years of follow-up. BCVA and central subfield thickness (CST) were collected at baseline, 12 months and 24 months of follow-up. RTD was calculated as the absolute difference between measured and normative CST values at each time point. Linear regression analyses were performed between RTD and BCVA and between CST and BCVA. One hundred and four eyes were included in the analysis. The RTD was 177.0 (117.2) μm at baseline, 97.0 (99.7) μm at 12 months and 89.9 (75.3) μm at 24 months of follow-up (P < .001). RTD showed a moderate association with BCVA at baseline (R2=0.134, p<0.001) and 12 months (R2=0.197, p<0.001), and a substantial association at 24 months (R2=0.272, p<0.001). The CST showed a moderate association with BCVA at baseline (R2=0.132, p<0.001) and 12 months (R2=0.136, p<0.001), while the association was weak at 24 months (R2=0.065, p=0.009). In conclusion, RTD showed a good association with visual outcome in DME eyes undergoing intravitreal treatment.

In many advanced industrial applications, the thickness is a critical index, especially for metallic coatings. However, the variance of lift-off spacing between sensors and test pieces affects the measured voltage or impedance, which leads to unreliable results from the sensor. Massive research works have been proposed to address the lift-off issue, but few of them applies to the thickness measurement of planar metallic films with finite-size circular (disk) geometry. Previously, a peak-frequency feature from the swept-frequency inductance was used to compensate the measurement error caused by lift-offs, which was based on the slow-changing rate of impedance phase term in the Dodd-Deeds formulas. However, the phase of measured impedance is nearly invariant merely on a limited range of sample thicknesses and working frequencies. Besides, the frequency sweeping is time-consuming, where a recalibration is needed for different sensor setups applied to the online real-time measurement. In this paper, a single-frequency algorithm has been proposed, which is embedded in the measurement instrument for the online real-time retrieval of thickness. Owing to the single-frequency measurement strategy, the proposed method does not need to recalibrate for different sensor setups. The thickness retrieval is based on a triple-coil sensor (with one transmitter and two receivers). The thickness of metallic disk foils is retrieved from the measured electrical resistance of two transmitter-receiver sensing pairs. Experiments on materials of different electrical conductivities (from direct current), thicknesses and planar sizes (radii) have been carried out to verify the proposed method. The error for the thickness retrieval of conductive disk foils is controlled within 5 % for lift-offs up to 5 mm.

Defect detection in ferromagnetic substrates is often hampered by non-magnetic coating thickness variation when using conventional eddy current testing technique. The lift-off distance between the sample and the sensor is one of the main obstacles for the thickness measurement of non-magnetic coatings on ferromagnetic substrates when using the eddy current testing technique. Based on the eddy current thin-skin effect and the lift-off insensitive inductance (LII), a simplified iterative algorithm is proposed for reducing the lift-off variation effect using a multi-frequency sensor. Compared to the previous techniques on compensating the lift-off error (e.g., the lift-off point of intersection) while retrieving the thickness, the simplified inductance algorithms avoid the computation burden of integration, which are used as embedded algorithms for the online retrieval of lift-offs via each frequency channel. The LII is determined by the dimension and geometry of the sensor, thus eliminating the need for empirical calibration. The method is validated by means of experimental measurements of the inductance of coatings with different materials and thicknesses on ferrous substrates (dual-phase alloy). The error of the calculated coating thickness has been controlled to within 3 % for an extended lift-off range of up to 10 mm.

Background. The minimum wage has become a standard measure in economic and social policies of countries all over the world and it directly or indirectly affects between 20% and 30% of the labour force. The primary objective of this measure is to guarantee that workers receive a minimum wage that allows them to lead a decent life, thereby reducing inequality and poverty. However, studies on the minimum wage have not focused on assessing the effects on these dimensions, but on employment, anticipating a negative effect (in line with the traditional theory of perfect competition), which they have been unable to substantiate. Objectives and Methods. The objective of this study is to address this research gap by analysing the effects of minimum wage increases on income inequality and poverty. To this end, firstly, a systematic review of the empirical analyses was conducted using the PRISMA methodology, with a view to ensuring that all empirical evidence was available. Secondly, the Spanish case was examined. As the significant increase in minimum wage in Spain in 2019 (21,3% in real terms) presents an invaluable opportunity to utilise this event as a natural experiment to generate new evidence, a difference-in-differences approach was employed to assess the impact of this phenomenon. Results. In relation to the first objective, a number of non-exhaustive and outdated literature reviews have been identified, which have been subjected to a critical review. In addition, a total of 31 articles that empirically analysed this relationship in recent years (2020-2024) have been included. The available evidence indicates a clear inverse relationship between the minimum wage and inequalities and poverty. Regarding the Spanish case, there has been a dearth of scientific studies on this subject, particularly in the context of the significant increase observed in 2019, which makes this article of particular relevance. The results are statistically significant, demonstrating an increase of approximately 18% in annual gross income among low-income households, relative to the control group. Furthermore, there is evidence of a spillover effect and a lighthouse effect towards income groups closer to the treatment group. This suggests that the minimum wage increase has a positive impact on the income of workers earning just above the new minimum and even below it. This result is consistent with the existing literature, which shows that minimum wage increases have a positive effect on the income of workers earning slightly above or below the new minimum. Scientific contribution. In doing so, two new basic scientific contributions were made: a systematic, exhaustive, and up-to-date literature review (up to June 2024), as there is, to our knowledge, no recent systematic review of this relationship (minimum wage vs. inequality). Then, the introduction of new scientific evidence demonstrating that a significant increase in the minimum wage can significantly improve the income of low-wage earners without the adverse effects that would otherwise disrupt this positive effect, thereby reducing income inequality and poverty. As a limitation of the study, it would be desirable to delve deeper into other aspects not analysed here, such as the effects on productivity and consumption. Furthermore, it has not been possible to analyse the medium and long-term effects, due to data limitations. Nevertheless, there is evidence that inequality and poverty are on a downward path.

This paper proposes the optimization method for the minimum mass of permanent magnet (PM) excited homopolar inductor alternator (HIA) with air-gap winding used for high-speed driving system. The calculation results show that there is an optimal value for shell diameter and unit number of HIA to make the mass to be smallest. A 1 MW at 22000 rpm PM excited HIA is designed. The analytical results are verified by the FEM simulations. The losses, temperature rise, rotor stress and modal of the PM excited HIA are also analyzed. The calculation results show that the solid rotor eddy-current losses and the temperature rise of PM excited HIA are acceptable. Also the rotor strength is adequate, and the rotor system is a stiffness rotor, and it can safely operate. Finally, the comparison between PM excited HIA and permanent magnet rotor machine is discussed.

As urban development increases in density, the space to grow urban trees becomes more constrained. In heavily developed areas, small stature trees can be planted to reduce both above- and below-ground conflicts with infrastructure elements. However, even these species have their limits when placed in extremely confining conditions. In this study, we build on past work to determine the minimum planting widths of small stature urban trees. We found that species, stem diameter, and the height at which stem diameter measurements occurred were all strong predictors of trunk flare diameter (adjusted R² of 0.843). Additionally, we modelled the relationship between planting space and the presence or absence of hardscape conflicts – using the predictions derived from this effort to project the potential cost savings in two United States cities. Study results provide a guideline to create sufficient space for urban trees and minimize infrastructure damage and associated cost savings.

During the extraction of hard coal in Polish conditions, methane is emitted, which is referred to as mine gas. As a result of the desorption of methane, a greenhouse gas is released from coal seams. In order to reduce atmospheric emissions, methane from coal seams is captured by a methane drainage system. On the other hand, methane, which has been separated into underground mining excavations, is discharged into the atmosphere with a stream of ventilation air. For many years, Polish hard coal mines have been capturing methane to ensure the safety of the crew and the continuity of mining operations. As a greenhouse gas, methane has a significant potential, as it is more effective at absorbing and re-emitting radiation than carbon dioxide. The increase in the amount of methane in the atmosphere is a significant factor influencing global warming, however, it is not as strong as the increase in carbon dioxide. Therefore, in Polish mines, the methane-air mixture captured in the methane drainage system is not emitted to the atmosphere, but burned as fuel in systems, including cogeneration systems, to generate electricity, heat and cold. However, in order for such use to be possible, the methane-air mixture must meet appropriate quality and quantity requirements. The article presents an analysis of changes in selected parameters of the captured methane-air mixture from one of the hard coal mines in the Upper Silesian Coal Basin in Poland. The paper analyses the changes in concentration and size of the captured methane stream through the methane capturing system. The gas captured by the methane drainage system, as an energy source, can be used in cogeneration, when the methane concentration is greater than 40%. Considering the variability of CH4 concentration in the captured mixture, it was also indicated which pure methane stream must be added to the gas mixture in order for this gas to be used as a fuel for gas engines. The balance of power of produced electric energy in gas engines is presented. Possible solutions ensuring constant concentration of the captured methane-air mixture are also presented.

This paper deals with the analysis of the temperatures in a group of 36 African countries. By looking at the maximum, minimum and the range (the difference between the maximum and the minimum) and using a long memory model based on fractional integration and cointegration, we first show that all series display a long memory pattern, with a significant positive time trend in 29 countries for the maximum temperatures and in 33 for the minimum ones. Looking at the range, the estimated value for the order of integration is smaller than the one based on maximum or minimum temperatures in 17 countries. Performing fractional cointegration tests between the maximum and minimum temperatures, our results indicate that the two series cointegrate in the classical sense (i.e., with a short memory equilibrium relationship) in a group of 11 countries, and there is another group of eight countries displaying cointegration in a fractional sense. The remaining 17 countries with no evidence of cointegration are therefore at the very high risk of climate change due to the absence of long-term comovement in their maximum and minimum temperatures. Findings in this paper are of tremendous interpretations and relevance for the analysis and climate projections in Africa.

Lake ice thickness (LIT) is a sensitive indicator of climate change identified as a thematic variable of Lakes as an Essential Climate Variable (ECV) by the Global Climate Observing System (GCOS). Here, we present a novel and efficient analytically based retracking approach for estimating LIT from high-resolution Ku-band (13.6 GHz) synthetic aperture radar (SAR) altimetry data. The retracker method is based on the analytical modeling of the SAR radar echoes over ice-covered lakes that show a characteristic double-peak feature attributed to the reflection of the Ku-band radar waves at the snow-ice and ice-water interfaces. The method is applied to Sentinel-6 Unfocused SAR (UFSAR) and Fully Focused SAR (FFSAR) data, with their corresponding tailored waveform model, referred to as the SAR_LITand FFSAR_LITretracker, respectively. LIT retrievals from Sentinel-6 SAR data at different posting rates are evaluated against those obtained from thermodynamic lake ice model simulations and Low Resolution Mode (LRM) Sentinel-6 and Jason-3 data over two ice seasons during the tandem phase of the two satellites, allowing precise assessment of the continuity between LRM and SAR LIT retrievals. Consistency checks of the Sentinel-6 SAR LIT estimates are also performed using optical/radar images that provide information on the snow/ice conditions on the same dates. The analysis is performed on Great Slave Lake and Baker Lake (Canada) that differ in terms of lake size, bathymetry, snow/ice properties, and seasonal evolution of LIT. The accuracy of the LIT estimates with the SAR LIT retrackers is on the order of 5 cm once the ice is well established on the lakes, meeting the GCOS requirements of LIT measurement uncertainty, which is a factor of 2 to 3 times better than that of LIT obtained with LRM data, bringing a further improvement compared to previous analyses and methods. The SAR LIT retrackers presented are promising tools for monitoring the inter-annual variability and trends in LIT from current and future SAR altimetry missions.

Pachychoroid neovasculopathy (PNV) is a pachychoroid-spectrum disease. As blood circulation throughout the choroid may be involved in PNV pathogenesis, analysis using ultra-wide-field (UWF) fundus imaging is crucial. We evaluated choroidal thickness after half-fluence photodynamic therapy (PDT) combined with intravitreal aflibercept injection for PNV using UWF swept-source optical coherence tomography. Seventeen eyes with PNV that underwent half-fluence PDT with adjuvant single intravitreal aflibercept injection were analyzed. To compare choroidal thicknesses in the central and peripheral choroids, we set subfields <3, <9, and 9–18 mm from the fovea. The <9- and 9–18-mm subfields were divided into four quadrants. Choroidal thickness in each subfield decreased significantly after half-fluence PDT (P<0.001); this reduction was more pronounced in the central area. We also investigated the relationship between the dominant side of the deep choroidal veins that harbor choroidal vein efflux from the macula. When choroidal thickness in the supratemporal and infratemporal 9x9-mm subfields were evaluated, the ratio of choroidal thickness reduction was not significantly different between the dominant and non-dominant sides. The dominant side was not associated with the extent of choroidal thickness reduction in PNV. In conclusion, half-fluence PDT caused thinning of the entire choroid, especially in the central area, in PNV.

Systematic results of lattice dynamical calculation are reported for the novel (SiC)m/(GeC)n superlattices (SLs) by exploiting a modified-linear chain model (M-LCM) and a realistic rigid-ion- model (RIM). By employing the bond polarizability method in the framework of M-LCM, we have simulated Raman intensities for the graded (SiC)10-D/(Si0.5Ge0.5C)D/(GeC)10-D/(Si0.5Ge0.5C)D SLs by carefully integrating interfacial layer thickness D (≡ 0, 1, 2, 3 monolayers (MLs)). The variation of D has initiated considerable up (down) shifts of GeC-, (SiC)-like Raman peaks in the middle of the optical phonon frequency region. With D = 3 MLs, the maximum energy shift (by ~ 47 cm-1) of SiC-like modes has caused substantial changes in the Raman intensity profiles linked to the localization of atomic displacements at the interfacial transition regions. This effect can be considered as a vital tool for authenticating the interfacial structures in technologically important SLs. By using a RIM, we have reported SL phonon dispersions along the growth [001] as well as in the plane [100], [110] perpendicular to the growth. Our simulations of phonons in the acoustic mode region have not only confirmed the formation of minigaps at the zone center and zone edges but also provided evidence of anti-crossing and phonon confinement. Besides examining angular dependence of zone-center optical modes, we have also discussed phonon folding, confinement and anisotropic behavior in (SiC)m/(GeC)n SLs.

The Combined Inversion of Surface and AeRosols (CISAR) algorithm for the joint retrieval of surface and aerosol single scattering properties has been further developed in order to extend the retrieval to clouds and overcome the need for an external cloud mask. Pixels located in the transition zone between pure cloud and pure aerosol are often discarded by both aerosol and cloud algorithms, despite being essential for studying aerosol-cloud interactions, which still represent the largest source of uncertainty in climate predictions. The proposed approach aims at filling this gap and deepening the understanding of aerosol properties in cloudy environments. The new CISAR version is applied to Sentinel-3A/SLSTR observations and evaluated against different satellite products and ground measurements. The spatial coverage is greatly improved with respect to algorithms processing only pixels flagged as clear sky by the SLSTR cloud mask. The continuous retrieval of aerosol properties without any safety zone around clouds opens new possibilities for studying aerosol properties in cloudy environments.

Plants characterized by a soft or weak steam, such as climbing plants, need to find a potential support (e.g., wooden trunk) to reach greater light exposure. Since Darwin’s research on climbing plants, several studies on their searching and attachment behaviors have demonstrated their unique ability to process different support features to modulate their movements accordingly. Nevertheless, the strategies underlying this ability are yet to be uncovered. The present research tries to fill this gap by investigating how the interaction between above- (i.e., stem, tendril, …) and belowground (i.e., the root system) plant organs influence the kinematics of the approach-to-grasp movement. With three-dimensional (3D) kinematical analysis, we characterized the movement of pea plants (Pisum sativum L.) towards a support with different thicknesses above and belowground (i.e., thin below, thick aboveground, or the opposite). As a control condition, the plants were presented to supports with the same thickness below- and aboveground (i.e., either entirely thin or thick). The results suggest an integration between the information from below- and aboveground for driving the reach-to-grasp behavior of the aerial plant organs. Information about the support conveyed by the root system seems particularly important to fulfil the end-goal of the movement.

The hot rolling in the process chain of the aluminium rolled products present the critical element of material quality and influence on productivity. The desire to increase the letter demand modifications of hot rolling, consequential changes of microstructure, crystallographic texture, mechanical and formability properties must be knowledge and consistently considered in planning the rolling process and rolled product. Achieving lower thicknesses of the hot-rolled band would enable fewer passes with cold rolling; consequently, hot rolling with the same number of passes will complete with lower temperatures. Microstructural and texture characterization with the optical microscope and scanning electron microscope for the hot-rolled band 3.25 mm the smaller grains appeared in the center of the cross-section, unlike for the hot-rolled band 6 mm, the smaller grains were detected on the upper and bottom position of the cross-section. Furthermore, the comparison shows also that the hot-rolled band 6 mm has 64 % of random texture components and 83 % of recrystallized grains, and the proportional adjustment for the hot-rolled band 3.25 mm has the 42 % of random texture components and 55 % of recrystallized grains. For the mechanical testing results, the elongation values in rolling and transverse directions significantly differ just in the case of a hot rolled band of 3.25 mm. Consequently, the earing results are more than 1.5 % higher for the hot-rolled band, 3.25 mm, than the hot-rolled band, 6 mm.

Learning systems have been very focused on creating models that are capable of obtaining the best results in error metrics. Recently, the focus has shifted to improvement in order to interpret and explain their results. The need for interpretation is greater when these models are used to support decision making. In some areas this becomes an indispensable requirement, such as in medicine. This paper focuses on the prediction of cardiovascular disease by analyzing the well-known Statlog (Heart) Data Set from the UCI’s Automated Learning Repository. This study will analyze the cost of making predictions easier to interpret by reducing the number of features that explain the classification of health status versus the cost in accuracy. It will be analyzed on a large set of classification techniques and performance metrics. Demonstrating that it is possible to make explainable and reliable models that have a good commitment to predictive performance.

Background: Evaluating muscle mass and function among stroke patients is important. However, evaluating muscle volume and function is not easy due to the disturbance of consciousness and paresis. Temporal muscle thickness (TMT) has been introduced as a novel surrogate marker for muscle mass, function, and nutritional status. We herein performed a narrative literature review on temporal muscle and stroke to understand the current meaning of the TMT in the clinical stroke practice. Methods: The search was performed in PubMed, last updated in October 2021. Report on temporal muscle morphomics and stroke-related diseases or clinical entities were collected. Results: Four studies reported on TMT and subarachnoid hemorrhage, 2 intracerebral hemorrhage, 2 ischemic stroke, 2 standard TMT values, and 2 nutritional status. TMT was reported as a prognostic factor for several diseases, surrogate markers for skeletal muscle mass, and an indicator of nutritional status. Computed tomography, magnetic resonance imaging, and ultrasonography were used to measure TMT. Conclusions: TMT is gradually used as a prognostic factor of stroke or surrogate marker for skeletal muscle mass and nutritional status. Establishing standard methods to measure TMT and large prospective studies to investigate the further relationship between TMT and diseases are needed.

The minimum ignition energy (MIE) has been extensively studied via experiments and simulations. However, our literature review reveals little quantitative consistency, with results varying for f=1.0 from 0.324 to 1.349 mJ, and for f=0.9 from 0.22 to 0.944 mJ. Therefore, there is a need to resolve these discrepancies. This RANS study aims to partially address this knowledge gap. Additionally, it presents other flame evolution parameters essential for robust combustion design. Using the reactingFOAM solver we predict the threshold energy required to ignite the fuel mixture. For this, the single step using the Arrhenius law is selected to model ignition in the flame kernel of stochiometric and lean CH₄/air mixtures, allowing it to develop into a self-sustained flame. The ignition power density, an energy quantity normalised with volume is incrementally varied keeping the kernel critical radius r_s constant 0.5 mm in the quiescent mixture of two equivalence ratios fs 0.9, and 1.0, for varied operating pressures 1, 5 and 10 bar at constant initial temperature 300 K. The minimum ignition energy is validated with twelve independent 1 bar data sets both numerical and experiments. Finally, a mathematical formulation of MIE is devised, a function of pressure and equivalence ratio shows a slightly curved relationship.

Law of conservation of energy is the most well-established law of modern physics. But, inflationary cosmological model which assumes the universe to be created from a point of singularity has not been able to identify the source of energy for creation of this universe. As per uncertainty principle, a quantum vacuum fluctuation can at most create energy of ~10^-8 kg in a Planck time of ~5.4 ×10^-44 s whereas total positive energy due to matter/vacuum existing in the universe is more than ~10⁵⁴ kg. To solve this problem, we have recently published a new cosmological model (Biswaranjan Dikshit, Canadian Journal of Physics, 100, 218-225, [2022]) in which we have mathematically proved that the total energy of the universe can be zero right from the beginning of the universe to till date due to negative gravitational potential energy and thus law of conservation of energy can be satisfied during creation of the universe from nothing. In this article, starting from a simple argument, we explain why net energy of the universe can be zero only in our model, not in standard cosmological model. An interesting fact pointed out in this paper is that the factor ~10⁶² by which radius of universe has increased from its starting value of ~10^-36 m to present value of ~10²⁶ m is same as the factor by which positive energy has increased from Planck energy ~10^-8 kg to present value ~10⁵⁴ kg. This is in agreement with our new model that predicts the positive energy of universe to be proportional to the radius of universe. We also bring out to the notice that zero energy universe is possible only if smallest possible length in nature is, l_min=l_p(π/2)^1/2 = 2.0×10^-35 m. Minimum possible length is important in theory of quantum gravity and string theory.

The aim of this paper is to analyze the real impact of ICT skill mismatch on SME’s sustainable competitiveness in presence of minimum wage guaranteed. As part of public policies – the minimum wage need to maintain a balance between increasing employment and not being a burden for the companies, leading them to bankruptcies, especially in times of disruptive change in which economy have to be more resilient. The rapid progress in information and communication technologies has dramatically redefined the rising unemployment as a result of skills mismatch. This paper aims to understand, on one side if, there is a match between the supply demand of ICT skills and how increasingly powerful digital technologies affect skills, jobs, and the demand for human labour. On the other, if increasing productivity and a fair minimum wage could be an integrated approach in stimulating SME’s in increasing sustainable competitiveness.

The successful handling of large semiconductor wafers is crucial for scaling up their production. Early-stage warpage control allows to prevent undesirable asymmetric warpage, known as wafer bifurcation or buckling. Indeed, even in a gravity-free environment, thinning an 8" or 12" semiconductor wafer can result in warpage and bifurcation. To mitigate this issue, the taiko method, which involves creating a thicker ring region around the rim of the wafer, has been widely used. Previous research has focused on the theoretical factors affecting the warpage of a backside metalized taiko wafer. This work extends the case to a front-side metalized taiko wafer and introduces the concept of the equivalent thickness of a taiko wafer. The equivalent thickness of a taiko wafer, influenced by the ring region, lies in between the thickness of the central region and that of the annular region. Because of the limited number of taiko wafers that can be produced on a production line, modelling can be beneficial. In this work we compared the results of a developed analytical model with those obtained from a finite element analysis (FEA) approach with ANSYSY® software to model the equivalent thickness of a taiko wafer. We investigated the curvature as a function of the stress of the metal layer, considering key design factors such as the substrate region thickness, the thickness of the thin metal film, the step height, and the width of the ring region. By systematically varying the thickness of the central region of the taiko wafer, we explored the curvature as a function of stress induced by thermal load in the linear regime and determined the slopes in the linear region of the curvature vs. stress curves. The aim of this study is to identify regularities and similarities with the Stoney equation and investigate the validity of the analytical approach for the case of a taiko substrate. It results that there is a good agreement between the analytical model of a taiko wafer and the numerical analysis gained by the FEA methods.

Epitaxial lithium ferrite (LiFe5O8) films with different thicknesses have been successfully fabricated on SrTiO3 (001) substrates by magnetron sputtering deposition technique. The microstructural and magnetic properties are characterized by advanced transmission electron microscope and magnetic measurement device. It was found that the formation of structural defects can be influenced by the thickness of the film. Apart from the misfit dislocations, the orientation domains form in thinner film and twin boundaries appear in thicker film, respectively, contributing to the misfit strain relaxation in the heterosystem. The magnetic measurement shows that the thinner films have enhanced magnetization and a relatively lower coercive field compared with the thicker films containing the antiferromagnetic twin boundaries. Our results provide a way for tuning the microstructure and magnetic properties of lithium ferrite films by changing the film thickness.

In order to study the strength changes of concrete specimens under different loading conditions, based on the principle of minimum energy dissipation and from the Angle of concrete failure energy per unit area, the finite element numerical simulation software was applied to concrete specimens with different failure modes of tension, compression, bending and torsion, and the double-broken line damage constitutive model was adopted to simulate and analyze the failure forms of concrete specimens under different loading conditions. The failure area and failure energy of each specimen during loading were quantitatively calculated under each failure mode, and the relationship between the failure area and failure energy consumed under different failure modes was analyzed. The results show that under different failure modes, the failure area of concrete specimens is different, the energy consumed during failure is different, and the strength is different. However, in the process of failure, no matter how the failure mode changes, the failure energy W per unit area remains unchanged and is a constant, which is related to the physical properties of concrete itself.

Nowadays, the increasingly serious environmental pollution and energy problems urgently require internal combustion engine-based transportation vehicles to upgrade or replace, so the new energy transportation vehicles based on hybrid power and fuel cells have gradually stepped on the stage and continue to innovate. The shipping industry is one of the main sources of global greenhouse gas emissions. The development of clean energy ships represented by fuel cells has attracted wide attention. Fuel cell has the advantages of clean, pollution-free and low noise, but it has some disadvantages such as insufficient dynamic response performance and fast performance decay. Limited by the characteristics of a single energy source, a variety of energy sources and bidirectional DC converters are usually mixed together to form a hybrid ship to improve the flexibility, stability and economy of the ship, and enhance its adaptability to complex sea conditions through the reconfiguration of power system energy. Taking fuel cell ferry "FCS Alsterwasser" as the research object, this study proposed an improved equivalent minimum hydrogen consumption energy management strategy based on fuzzy logic control. First, the power system of the modified mother ship was simulated, and a hybrid power system including fuel cell, lithium iron phosphate battery and supercapacitor was proposed. Then, the dynamic system simulation model and double closed loop PI control model are established in MATLAB/Simulink, and the reliability of the model is verified by the simulation analysis of charge and discharge characteristics. Then, the feasibility of the proposed method is demonstrated by designing simulation experiments based on typical working conditions of the mother ship. The simulation results show that under the premise of meeting the load requirements, the control strategy designed in this paper has a better optimization effect than the S-type penalty function in terms of lithium battery power, lithium battery SOC, bus voltage stability and equivalent hydrogen consumption, which improves the stability and economy of the power system, and has certain engineering practical value.

Background: The isoflurane minimum alveolar concentration (MAC) was measured in rats chronically treated with WIN 55,212-2. Methods: The isoflurane MAC was determined in 24 male rats from the end expiratory samples at time of tail clamping under the following conditions: without treatment (MACISO), in rats treated for 21 days with WIN 55,212-2 (MACISO+WIN55) and other group 8 days after stopping treatment for 21 days with WIN 55,212-2 (MACISO+WIN55+8D). Results: The MACISO was 1.32 ± 0.06. In the MACISO+WIN55 group the MAC increase to 1.69 ± 0.09 (28%). After 8 days stopping treatment, MAC did not decrease significantly 1.67 ± 0.07 (26%). Conclusions: The administration for 21 days of WIN 55,212-2 increases the MAC of isoflurane in rats; this effect does not disappear after 8 days of discontinuing treatment with the synthetic cannabinoid.

According to Landauer’s principle, the energy of a particle may be used to record or erase N number of information bits within the thermal bath. The maximum number of information N recorded by the particle in the heat bath is found to be inversely proportional to its temperature T. If at least one bit of information is transferred from the particle to the medium, then the particle might exchange information with the medium. Therefore for at least one bit of information, the limiting mass that can carry or transform information assuming a temperature T= 2.73 K is equal to m = 4.71810-40 kg which is many orders of magnitude smaller that the masse of most of today’s elementary particles. Next, using the corresponding temperature of a graviton relic and assuming at least one bit of information the corresponding graviton mass is calculated and from that, a relation for the number of information N carried by a graviton as a function of the graviton mass mgr is derived. Furthermore, the range of information number contained in a graviton is also calculated for the given range of graviton mass as given by Nieto and Goldhaber, from which we find that the range of the graviton is inversely proportional to the information number N. Finally, treating the gravitons as harmonic oscillators in an enclosure of size R we derive the range of a graviton as a function of the cosmological parameters in the present era

In this paper, we first investigate secure communications for a two-hop interference relay system in the wireless Internet of Things (IoT), where K source-destination pairs communicate in the presence of an eavesdropper. Explicitly, we jointly design source, relay and destination matrices upon minimizing total mean-squared error (MSE) of all legitimate destinations while keeping the MSE at eavesdropper above a certain threshold. We illuminate that the joint design of the source, relay and destination matrices subject to both secrecy and transmit power constraints. More specifically, we proposed an efficient iterative distributed algorithm to simplify the process of the joint design for optimal source, relay and destination matrices. Furthermore, the convergence of the iterative distributed algorithm is described. Additionally, the performances of the proposed algorithm, including both its secrecy rate and MSE, are characterized with the aid of simulation results. We demonstrate that our proposed algorithm outperforms the traditional approach. As a benefit, secure communications can be guaranteed by using the proposed algorithm for the multiple input multiple output (MIMO) interference relay IoT network in the presence of an eavesdropper.

Traditional metals such as stainless steel, titanium and cobalt chrome are used in biomedical applications (implants, scaffolds etc.) but suffer from issues such as osseointegration and compatibility with existing bone. One way to improve traditional biomaterials is to incorporate ceramics with these metals so that their mechanical properties can be similar to cortical bones. Tricalcium phosphate is such a ceramic with properties so that it can be used in human body. This research explores the use of binder jetting based additive manufacturing process to create a novel biocomposite made of cobalt chrome and tricalcium phosphate. Experiments were conducted and processing parameters were varied to study their effect on the printing of this biocomposite. Layer thickness, binder saturation and drying time affected the dimensional tolerance and the density of the green samples. This effect is important to understand so that the material can be optimized for use in specific applications.

In estimating the maximum and minimum index void ratios for mixtures of sand and silt, the values of several empirical constants must be determined based on the type of sand and silt involved. These empirical constants are the filling coefficient, a, and embedment coefficient, b, both of which can be determined either through lab testing or correlations. These constants are then used in equations to predict the maximum and minimum index void ratios of the sand-silt mixtures. The study reported here developed simple correlations for estimating the filling and embedment coefficients using readily obtained laboratory data. These models were found to be excellent in developing filling and embedment coefficients that accurately (R2 values typically of 0.94 or greater.) predicted values of the index void ratios for sand and silt mixtures.

Permafrost thaw is an important aspect of Earth’s carbon cycles. Initial estimates suggest that permafrost thaw could contribute anywhere between 20 to 500 Gt of CO2-eq by 2100. These estimates are all fundamentally centered around one number: active layer thickness (ALT). The deeper the ALT, the more emissions. Unfortunately, ALT is a highly spatially heterogeneous number and determined by numerous thermal, soil hydrology, and geomorphological effects. The remotely sensed active layer thickness (ReSALT) algorithm was introduced in 2010 to provide scientists with a way to model ALT heterogeneously at meter-scale resolution. However, upon inspection, this work shows that ReSALT’s modeling approach is self-inconsistent when using a variable soil porosity model. This work then introduces SCReSALT (Self-Consistent ReSALT) to solve that problem. Experimental comparisons to a past study in Utqiagvik (formerly Barrow), Alaska show significant improvement and suggest that SCReSALT should become a standard tool in permafrost thaw modeling. Code to reproduce all results can be found at https://github. com/jmathur25/permafrost-prediction.

The aim of this research is to investigate the influence of model height employed in the deep drawing of orthodontic aligner sheets on force transmission and aligner thickness. Forty sheets (Zendura FLX) were thermoformed over four models of varying heights (15, 20, 25, and 30 mm). Normal contact force generated on the facial surface of the upper right central incisor (Tooth 11) was measured using pressure-sensitive films. Aligner thickness around Tooth 11 was measured at five points. A digital caliper and a micro-computed tomography (µ-CT) were employed for thickness measurements. The normal contact force exhibited an uneven distribution across the facial surface of Tooth 11. Model 15 displayed the highest force (88.9±23.2 N), while Model 30 exhibited the lowest (45.7±15.8 N). The force distribution was more favorable for bodily movement with Model 15. Thickness measurements, conducted using a digital caliper and µ-CT, revealed substantial thinning of the aligner after thermoforming. This thinning was most pronounced at the incisal edge (50% of the original thickness) and least at the gingivo-facial part (85%). Additionally, there was a progressive reduction in aligner thickness with increasing model height, which was most significant on the facial tooth surfaces. We conclude that the thermoplastic aligner sheets undergo substantial thinning during the thermoforming process, which becomes more pronounced as the height of the model increases. As a result, there is a decrease in both overall and localized force transmission, which could lead to increased tipping by the aligner and a diminished ability to achieve bodily movement.

Two-dimensional (2D) materials show advantages as surface enhanced Raman scattering (SERS) substrate over traditional noble metals, such as chemically inert flat surface and uniform SERS signals. However, due to the low density of free electrons of 2D materials, the enhancement mechanism is mainly restricted to chemical enhancement instead of electromagnetic enhancement, resulting a relatively low enhancement factor. In this work, we reported a sensitive 2D SERS substrate based on chemical vapor deposited MoN nanosheets with electromagnetic enhanced mechanism. The maximum enhancement factor can be 3×105 with a limit of detected concentration of 4×10-8 M, which is comparable to those noble metal SERS substrates without hot spots. The MoN nanosheets show strong surface plasmon resonance in the visible range as evidenced by the UV-vis absorption spectroscopy and first principle calculation. The MoN nanosheets SERS substrates exhibit excellent Raman signal uniformity within the nanosheets. Meanwhile, Distinct thickness dependent sensitivity was observed in the MoN nanosheets, higher sensitivity can be achieved by decreasing the thickness of the nanosheets. Furthermore, the MoN nanosheets SERS substrate also show high thermal stability, which can be annealed in air for more than 300℃ and maintain its SERS activity. The high stability of MoN nanosheets allows it to be reused for 20 cycles without obvious signal decay. The high sensitivity, stability, reusability and Raman signal uniformity, makes MoN nanosheets an ideal 2D SERS substrate for practical applications.

The process of full-thickness skin regeneration is complex and has many parameters involved, which makes it difficult to use a single dressing to meet the various requirements of the complete regeneration at the same time. Therefore, developing hydrogel dressings with multifunction, including tunable rheological properties and aperture, hemostatic, antibacterial and super cytocompatibility, is a desirable candidate in wound healing. In this study, a series of complex hydrogels were developed via the hydrogen bond and covalent bond between chitosan (CS) and alginate (SA). These hydrogels exhibited suitable pore size and tunable rheological properties for cell adhesion. Chitosan endowed hemostatic, antibacterial properties and great cytocompatibility and thus solved two primary problems in the early stage of the wound healing process. Moreover, the sustained cytocompatibility of the hydrogels was further investigated after adding FGF and VE-cadherin via the co-culture of L929 and EC for 12 days. The confocal 3D fluorescent images showed that the cells were spherical and tended to form multicellular spheroids, which distributed in about 40-60μm thick hydrogels. Furthermore, the hydrogel dressings significantly accelerate defected skin turn to normal skin with proper epithelial thickness and new blood vessels and hair follicles through the histological analysis of in vivo wound healing. The findings mentioned above demonstrated that the CS/SA hydrogels with growth factors have tremendous potential as multifunctional hydrogel dressings for full-thickness skin regeneration incorporated with hemostatic, antibacterial, sustained cytocompatibility for 3D cell culture and normal skin repairing.

This article presents, for the first time, the kinetics and the general conversion features of a 3-initiator system (A/B/N), based on proposed mechanism of Mokbel et al, for both free radical polymerization (FRP) of acrylates and the free radical promoted cationic polymerization (CP) of epoxides using copper complex as the initiator. Higher FRP and CP conversion can be achieved by co-initiators concentration [B] and [N], via the dual function of (i) regeneration [A], and (ii) generation of extra radicals S' and S. The FRP and CP conversion is proportional to, respectively, the nonlinear and linear power of bI[A][B], where b and I are the absorption coefficient and the light intensity, respectively. System in air has lower conversion than in laminate due to the oxygen inhibition effects. For thick samples (with thickness z), there is an optimal concentration [A*] which is inverse proportional (bzI), in contrast with very thin sample, in which the conversion is an increasing function of [A] and [B]. The unique feature of dark polymerization in CP conversion enables the polymerization to continue in living mode, in contrasts with that of the radical-mediated pathway in most conventional FRP. The measured results of Mokbel et al are well analyzed and matching the predicted features of our modeling.

This study reports a correlation between EEG and structural brain changes in patients after severe traumatic brain injury in a coma. The novelty of our approach was based on the combination of structural visualization (MRI) and functional neuroimaging (EEG) during tactile stimulation. The structural morphometry indicated a decrease of whole-brain cortical thickness, the gray-matter volume of the cortex, and subcortical structures in comatose patients compared to healthy subjects. In resting-state EEG, coma patients had significantly higher power of the slow-wave activity of 2-6 Hz and significantly less power of the alpha and beta rhythm. Importantly, coma patients showed a significant decrease of theta-rhythm power in tactile stimulation compared to the resting state, and this EEG pattern was not found in the control group. The decrease of the theta-rhythm power significantly correlated with the better outcome from a coma. Spectral changes in EEG in response to tactile stimuli showed no association with brain morphometric measures in healthy controls. In patients, decreasing theta-rhythm power correlated positively with the volume of whole-brain gray matter, right putamen, and insula; and negatively with the volume of damaged brain tissue. Increasing beta-rhythm power, specific tactile EEG response for a healthy brain, correlated with the cortical thickness of the somatosensory Paracentral and Precentral area. The observed decrease of gray-matter volume indicates brain atrophy in coma patients, which could be associated with neurodegeneration induced by injury. Our results also demonstrate that slow-wave desynchronization, as a nonspecific response to tactile stimulation, can serve as a sensitive index of morphometric changes after brain injury and coma outcome.

A study about influence of heat input on welding defects in vertical upward welding position for dissimilar material and thickness using a new variation of TIG welding torch is done with support of advanced inspection methods SEM and EBSD. With vertical upward welding position, control heat input plays an important role to keep the weld stabilization without defects. On the other hand, TIG welding process using a conventional TIG torch (conventional TIG welding process) has low efficiency and it is difficult to control heat input with high accuracy. So, it is considered that using conventional TIG torch is still a challenge for welding thin plates. In this case, a new variation of TIG torch has been developed. This torch used a constricted nozzle to improve plasma arc characteristics. As a result, it can control efficiently the heat input to prevent the excessive or insufficiency for joining thin sheets. For evaluation of welding quality, advanced examination methods SEM and EBSD were applied to directly observe the welding defects. From the results, the formation mechanism of blowhole inside weld zone in case of welding dissimilar material and thickness was discussed. It is pointed out that when sufficient welding current, the change from weld zone to base metal is uniform, no welding defects such as blowhole was seen. However, in case of low welding current, the thinner base metal is insufficient fusion and the change between weld zone and base metal is not uniform. The blowhole was observed at SS400 material side.

A new method for wide-area urban roof assessment of suitability for solar photovoltaics is introduced and validated. Knowledge of roof geometry and physical features is essential for evaluation of the impact of multiple rooftop solar photovoltaic (PV) system installations on local electricity networks. This paper begins by reviewing and testing a range of existing techniques for identifying roof characteristics. It was found that no current method is capable of delivering accurate results with publicly available input data. Hence a different approach is developed, based on slope and aspect using LIDAR data, building footprint data, GIS tools and aerial photographs. It assesses each roof’s suitability for PV installation. That is, its properties should allow the installation of at least a minimum size photovoltaic system. In this way the minimum potential solar yield for region or city may be obtained. The accuracy of the new method is then established, by ground-truthing against a database of 886 household systems. This is the largest validation of a rooftop assessment method to date. The method is flexible with few prior assumptions. It is based on separate consideration of buildings and can therefore generate data for various PV scenarios and future analyses.

The present state of the natural environment is significantly influenced by the construction sector. Due to the large amounts of consumed natural resources and materials as well as the high volume of emitted pollutants, the building industry is considered to have a key influence in achieving a global sustainable development. A considerable part of the ecological impact of the built environment is influenced by the energy consumed for creating appropriate indoor conditions as well as by the greenhouse gases that are emitted during the operation stage of a building’s life cycle. Therefore, the energy performances of existing buildings must be significantly improved in the near future. This paper analyzes the influence of the thermal insulation thickness of walls on the linear thermal transmittances and the heating demand of an existing building. The resulted values show that while increasing the insulation of the walls leads to a serious heat demand reduction, a deep renovation of the building cannot be achieved solely by using this solution.

Atrial fibrillation (AF) is a common cardiac arrhythmia associated with significant morbidity and mortality. The role of epicardial adipose tissue (EAT), particularly in the left atrium, has garnered attention in the pathophysiology of AF. This review aims to provide an overview of the association between the thickness of left atrial epicardial adipose tissue (LA-EAT) and the incidence of AF, while exploring the arrhythmogenic effects of LA-EAT and the impact of epicardial fat tissue changes with age and in pathological conditions. A comprehensive search of PubMed was conducted, and relevant studies were selected based on their inclusion criteria. The findings suggest that increased LA-EAT thickness is associated with an elevated risk of AF, potentially mediated through inflammatory and proarrhythmic effects. Age-related changes in epicardial fat tissue and alterations in pathological conditions, such as obesity, metabolic syndrome, and cardiovascular diseases, further contribute to the development and progression of AF. Further research is needed to deepen our understanding of these mechanisms and their clinical implications.

In this paper, we consider the temporal development of the optical density of the H$_\alpha$ spectral line in a hydrogen laser induced plasma. This is achieved by using the so-called duplication method in which the spectral line is re-imaged onto itself and the ratio of the spectral line with it duplication is taken to its measurement without the duplication. We asses the temporal development of the self-absorption of the H$_\alpha$ line by tracking the decay of duplication ratio from its ideal value of 2. We show that when 20% loss is considered along the duplication optical path length, the ratio is 1.8 and decays to a value of 1.25 indicating an optically thin plasma grows in optical density to an optical depth of 1.16 by 400 ns in the plasma decay for plasma initiation conditions using Nd:YAG laser radiation at 120 mJ per pulse in a 1.11$\times10^{5}$ Pa hydrogen/nitrogen gas mixture environment. We also go on to correct the H$_\alpha$ line profiles for the self-absorption impact using two methods. We show that a method in which the optical depth is directly calculated from the duplication ratio is equivalent to standard methods of self-absorption correction when only relative corrections to spectral emissions are needed.

This research was conducted to manufacture thermally expandable microspheres (TEMs) for vehicles’ underbody coating and to apply them on an industrial scale. TEMs heat resistance was studied depending on the ratios of a cross-linking agent and an initiator. This research focused on the content of a cross-linking agent and how it affected the results. The TEMs’ outer shell was thickened to solve the problem of the foam expansion ratio’s reduction that occurred due to the shrinkage after the maximum expansion (Tmax) was reached. After foaming, the cross-sectional thickness and surface of the sample with thickened outer shell were observed. The TEMs with the thickened shell showed the least shrinkage, which indicated excellent shrinkage stability, even after prolonged exposure to heat.

This research was conducted to manufacture thermally expandable microspheres (TEMs) for vehicles’ underbody coating and to apply them on an industrial scale. TEMs heat resistance was studied depending on the ratios of a cross-linking agent and an initiator. This research focused on the content of a cross-linking agent and how it affected the results. The TEMs’ outer shell was thickened to solve the problem of the foam expansion ratio’s reduction that occurred due to the shrinkage after the maximum expansion (Tmax) was reached. After foaming, the cross-sectional thickness and surface of the sample with thickened outer shell were observed. The TEMs with the thickened shell showed the least shrinkage, which indicated excellent shrinkage stability, even after prolonged exposure to heat.

Cerebral aneurysms come in a wide range of shapes and sizes, they can evolve over time and present significant changes. It is generally accepted that large aneurysms are more prone to rupture, but the rupture of small aneurysms has also been observed, indicating the presence of additional risks factors. The aim of this study is to assess the effects of the aneurysm size and wall thickness on its rupture risk by using fluid-structure interaction simulations. Six patient-specific geometries were chosen, four were used for studying the size effect and two for studying the thickness effect. Additional cases where the aneurysm was removed were included. It was found that thinner walls suffer from significantly greater stresses, whereas an increment in size means, in general, lower wall shear stress and greater equivalent stress. By removing the aneurysm, it could be noted that at the rupture point, the reduction in the time-averaged wall shear stress was 75%. Although the size of an aneurysm has a great impact in its rupture risk, its wall thickness needs to be considered, since even maintaining its size, the aneurysm could suffer from a thin-ning of its walls that can lead to structural failure.

This research program investigated the effects of layer thickness (50 and 100 microns) on the microstructure and mechanical properties of electron beam powder bed fusion (EBPBF) additive manufacturing of Inconel 625 alloy. The as-built 50 and 100 micron layer thickness components were also heat treated at temperatures above 1100 oC, which produced a recrystallized grain structure containing annealing twins in the 50 micron layer thickness components, and a duplex grain structure consisting of islands of very small equiaxed grains dispersed in a recrystallized, large-grain structure containing annealing twins. The heat treated component microstructures and mechanical properties were compared with the as-built components in both the build direction (vertical) and perpendicular (horizontal) to the build direction. Vickers microindentation hardness (HV) values for the vertical and horizontal geometries averaged 227 and 220 for the as-built 50 and 100 micron layer components, and 185 and 282 for the corresponding heat treated components. The yield stress values were 387 MPa and 365 MPa for the as-built layer horizontal and vertical 50 micron layer geometries, and 330 MPa and 340 MPa for the as-built 100 micron layer components. For the heat treated 50 micron components, the yield stress values were 340 and 321 MPa for the horizontal and vertical geometries, and 581 and 489 MPa for the 100 micron layer components, respectively. The elongation for the 100 micron layer as-built horizontal components was 28% in contrast to 65% for the corresponding 100 micron heat treated layer components, an increase of 132% for the duplex grain structure. However, the coarse grains containing annealing twins and the equiaxed small grain islands in the duplex structure for the heat treated components contained continuous carbides in the grain boundaries, and this may indicate sensitization and a reduction in corrosion resistance. These findings point to the potential mechanical property advantage for heat treatment of Inconel 625 alloy 100 micron layer thickness components fabricated by EBPBF.

Antimicrobial peptides (AMPs) are a promising alternative to antibiotics to combat drug resistance in pathogenic bacteria. However, the development of AMPs with high potency and specificity remains a challenge, and new tools to evaluate antimicrobial activity are needed to accelerate the discovery process. As a step toward direct prediction of the experimental minimum inhibitory concentration (MIC) of AMPs, we proposed MBC-Attention, a combination of a multi-branch CNN architecture and attention mechanism. Using a curated dataset of 3929 AMP against Escherichia coli, the optimal MBC-Attention model achieved an average Pearson correlation coefficient of 0.775 and an RMSE of 0.533 (log μM) in three independent tests of 393 sequences each. This results in a 5–12% improvement in PCC and 7–13% improvement in RMSE compared with RF and SVM models. Ablation studies confirmed that both attention mechanisms contributed to performance improvement.

Soil quality is related to food security and human survival and development. In recent years, due to the acceleration of urbanization and the increase of abandoned land, land degradation occurs, poor topsoil quality. In this study, the minimum data set (MDS) was constructed through principal component analysis (PCA) to determine the indicator data set for evaluating topsoil quality in Tieling County, China. In addition, the soil quality index (SQI) was calculated to analyze the spatial distribution characteristics and influencing reasons of topsoil quality in Tieling County. The re-sults showed that MDS included total potassium (TK), Clay, zinc (Zn), soil organic matter (SOM), soil water content (SWC), cation exchange capacity (CEC), pH, and copper (Cu). The MDS indicators can well replace all indicators to evaluate the topsoil quality in the study area. The overall soil quality of Tieling County showed a trend of low in the east and high in the west, and gradually increased from the hilly area to the plain area. The evaluation results are consistent with field research, which can provide reference for other topsoil quality evaluation, and it also provide a basis for the formulation of soil quality improvement measures.

Diffusion bonding is often used on pre-machined parts to generate internal cavities, e.g. for cooling injection molding tools close to the mold cavity. Only then, the workpieces are finished to their final dimensions. In the case of micro-process devices, however, it is essential to precisely control the deformation, as otherwise uncontrollable pressure losses will occur with channel cross-sections in the sub-millimeter range. Post-processing is not possible. The most important process parameters for diffusion bonding are temperature, dwell time and contact pressure, with the bonding temperature and contact pressure acting in opposite directions and showing a strong non-linear dependence on deformation. In addition, the deformation is influenced by a number of other factors such as the absolute size of the cross-section and the aspect ratio of the parts, the dimensions and distribution of the internal cross sections and the overall percentage of the cross-section to be bonded. In micro process engineering, small material cross-sections in the range of the materials microstructure can facilitate additional deformation mechanisms such as grain boundary sliding, which are not relevant at all for larger structures. For parts consisting of multiple layers, tolerances in thickness and roughness of multiple surfaces must be levelled, contributing to the percentaged deformation. This makes it difficult, especially in micro process engineering and in single or small series production, to determine suitable joining parameters in advance, which on the one hand do not cause unforeseen large deformations, but on the other hand reliably produce highly vacuum-tight components. Hence, a definition of a fixed percentaged deformation does not work for all kinds of components. This makes it difficult to specify parameters for surely obtain high-vacuum tight parts. For successful diffusion bonding, atoms must diffuse over the bonding planes, forming a monolithic part in which the original layers are no longer visible. Only then, mechanical properties identical to those of the base material, which has been subjected to identical heat treatment, can be achieved. In this paper, the impacts of different material cross section widths as well as of the aspect ratio on deformation were investigated. By accident, it was found that also accuracy of the temperature measurement may have a serious impact in terms of deformation.

For the polymer electrolyte fuel cell (PEFC), the separator thickness plays an important role to determine the weight, the volume and the costs of the PEFC. In addition, thermal management, i.e. temperature distribution is also important for the PEFC system to obtain higher performance. However, there were few reports investigating the relationship between the temperature distribution and the power generation performance such as current density distribution of PEFC operated at higher temperature (HT-PEFC). The aim of this study is to clarify the impact of separator thickness on the relationship between the temperature distribution and the current density distribution of HT-PEFC. This study has also investigated the impact of separator thickness on the relationship between the temperature distribution and the gases such as H2, O2 and the current density distribution of HT-PEFC numerically using CFD software COMSOL Multiphysics. The separator thicknesses of 2.0 mm, 1.5 mm and 1.0 mm were studied. In the study, the operation temperature and the relative humidity (RH) of supply gas were also changed. As a result, it was revealed that the optimum separator thickness was 2.0 mm to obtain higher power generation of HT-PEFC. Since the heat capacity in the case of the separator thickness of 2.0 mm was the largest among the separators investigated in this study, the dehydration of PEM and catalyst layer was smaller compared with the thinner separator thicknesses. It was also revealed that the impacts of separator thickness on distribution of gases, e.g. O2, H2O, and current density distribution became larger under higher temperature and lower RH conditions. This study also concluded that the tendency of temperature distribution matched those of O2, H2O and current density distributions.

Changing the film thickness to manipulate the microstructural properties has been considered as a potential method in practical application. Here, we report that atomic-scale structural properties regulated by film thickness in NiCO2O4(NCO)/CuFe2O4(CFO) bilayer heterostructure prepared on (001)-MgAl2O4 (MAO) substrate by means of aberration-corrected scanning transmission electron microscopy (STEM). The misfit dislocations at NCO/CFO interface and antiphase boundaries (APBs) bound to dislocations within the films both are found in NCO (40 nm)/CFO (40 nm)/MAO heterostructure to contribute to relaxation of mismatch lattice strain. In addition, the non-overlapping a/4[101]-APB is found and the structural transformation of this kind of APB is resolved at atomic scale. In contrast, only the interfacial dislocations form at interface without the formation of APBs within the films in NCO (10 nm)/CFO (40 nm)/MAO heterostructure. Our results provide evidence that formation of microstructural defects can be regulated by changing film thickness to tune magnetic properties of epitaxial bilayer spinel oxide films.