Dhaka one of the fastest-growing megacities in the world is increasingly vulnerable to urban flooding due to rapid urbanization, inadequate drainage infrastructure, and climate change-induced extreme weather events. This study presents the development of an urban flood forecasting system for Dhaka City using the MIKE+ hydrodynamic modeling software. The system integrates detailed hydrological and hydraulic models to simulate urban flooding scenarios, accounting for complex drainage networks and catchment characteristics. Real-time data from river gauges, rainfall stations, and drainage systems are incorporated to enhance the accuracy and reliability of the forecasts. The model's predictive capability is validated against historical flood events, demonstrating its effectiveness in forecasting flood extents, depths, and durations in critical areas of the city. This system serves as a valuable tool for city planners, emergency response teams, and decision-makers, enabling proactive flood management and risk mitigation. The study underscores the importance of such advanced modeling tools in safeguarding urban populations and infrastructures from the increasing threat of urban floods in Dhaka and similar rapidly urbanizing cities.

This study explores fault-tolerant consensus in leader-following heterogeneous multi-agent systems, focusing on actuator failures in uncrewed aerial vehicles (UAVs) and uncrewed ground vehicles (UGVs). An optimization-based fault-tolerant consensus algorithm is proposed. The algorithm utilizes the Euler-Lagrange formula to ensure system consistency under actuator failures, with the Lyapunov stability theory proving the asymptotic stability of the consistency error. The algorithm is applied to heterogeneous multi-agent systems of UAVs and UGVs to derive optimal fault-tolerant consensus control laws for each vehicle type. Simulation experiments give evidence for the feasibility of the proposed control strategy.

The rational design of magnetic carbon composites, encompassing both composition and microstructure, holds significant potential for achieving exceptional electromagnetic wave absorbing materials (EAMs). In this study, FeCo@CM composites was efficiently fabricated through an advanced microwave plasma assisted reduction chemical vapor deposition (MPARCVD) technique, offering high efficiency, low cost, and energy-saving benefits. By depositing graphitized carbon microspheres, the dielectric properties were significantly enhanced, resulting in improved electromagnetic wave absorption performances through optimized impedance matching and a synergistic effect with magnetic loss. A systematic investigation revealed that the laminar-stacked structure of FeCo exhibited superior properties compared to its spherical counterpart, supplying a higher number of exposed edges and enhanced catalytic activity, which facilitated the deposition of uniform and low-defect graphitized carbon microspheres. Consequently, the dielectric loss performance of the FeCo@CM composites was dramatically improved due to increased electrical conductivity and the formation of abundant heterogeneous interfaces. At a 40 wt% filling amount and a frequency of 7.84 GHz, the FeCo@CM composites achieved a minimum reflection loss value of -58.2 dB with an effective absorption bandwidth (fE) of 5.13 GHz. This study presents an effective strategy for developing high-performance EAMs.

This paper represents the first investigation into the consensus problem of linear time-varying multi-agent systems utilizing an event-triggered communication scheme. First, a general event-triggered consensus control scheme is proposed for a general category of linear time-varying multi-agent systems. Under some suitable assumptions, it is demonstrated that all agents’ states will converge exponentially, with Zeno behaviour being ruled out. Second, the consensus problem in a network of linear time-varying multi-agent systems with a spanning tree is investigated using the proposed control strategy. It demonstrates that the consensus issue for the specified system can be reformulated as a stabilization problem for an error system through a time-varying linear transformation. Then, the event-triggered consensus problem is just a special instance of the general event-triggered consensus problem mentioned above. Finally, to illustrate the efficacy of the event-triggered method proposed in this study, simulation results are shown.

Human induced climate change led to the recognition of Community-Based Adaptation (CBA) as one of the remedies in building adaptive capacity and resilience of communities. It recognizes the resources and the skills as well as the agency of communities in shaping the optimal strategy. CBA interventions are vital in addressing community needs and contextual specificities, enable participatory and inclusive engagement and thereby facilitate more profound adaptation impacts. Agent-based modelling (ABM) harbors the potential to be the ideal tool to support developing of tailored adaptation strategies while considering capacities, resources, skills, priorities, needs and the cultural context of local communities. ABM allows to capture the complex relationships among various components within community decision making on CBA actions, the CBA actions themselves and the environment. There exist plenty of tools, however they provide for varying degrees of freedom in agent definition, sensitivity analysis, scalability, experiment design and output analysis to name a few. A set of required key criteria for CBA modelling is developed and all available ABM modelling and simulation tools are assessed for their suitability for CBA. NetLogo emerges as the most fitting tool for incorporating and handling the special features of CBA. It is closely followed by GAMA and Envision. The article provides insights and guidance to researchers and practitioners in selecting ABM tools aligned with the specific requirements of their CBA simulations and projects.

Recent years have witnessed significant advances in reinforcement learning (RL), which has registered remarkable success in solving various sequential decision-making problems in machine learning. Most of the successful RL applications, e.g., the games of Go and Poker, robotics, and autonomous driving, involve the participation of more than one single agent, which naturally fall into the realm of multi-agent RL (MARL), a domain with a relatively long history, and has recently re-emerged due to advances in single-agent RL techniques. Although, typically, the communication protocol between agents is manually specified and not altered during training, recently, some papers have shown signs of trying to emerge a communication between agents on the one hand and, on the other hand, to understand what is exchanged between agents. So, there is a growing body of literature on this topic which includes qualitative and quantitative studies and the ones that apply mixed methods. This study presents the scoping review of the methodological strategies undertaken in a total of 16 research articles. The results present the critical appraisal of quantitative methods in terms of validity and reliability and for qualitative methods considering four trustworthiness factors. In the end, relevant insights are further explored with implications and reflections on how they can benefit one's research in the field.

Estimating parameters for multiple datasets can be time consuming, especially when the number of datasets is large. One solution is to sample from multiple datasets simultaneously using Bayesian methods such as adaptive multiple importance sampling (AMIS). Here we use the AMIS approach to fit a von Misses distribution to multiple datasets for wind trajectories derived from a Lagrangian Particle Dispersion Model driven from a 3D meteorological data. The primary objective is to characterise the uncertainties in wind trajectories in a form that can be used as inputs for predictive models of wind-dispersed insect pests and pathogens of agricultural crops for use in evaluating risk and in planning mitigation actions. Our results show that AMIS can significantly improve the efficiency of parameter inference for multiple datasets.

This paper presents a novel approach to designing beam codebooks for downlink multiuser hybrid multiple input multiple output (MIMO) wireless communication systems, leveraging multi-agent reinforcement learning (MARL). The primary objective is to develop an environment-specific beam codebook composed of non-interfering beams, learned by cooperative agents within the MARL framework. Machine learning (ML) based beam codebook design for downlink communications have been based on channel state information (CSI) feedback or only reference signal received power (RSRP) consisting of an offline training and user clustering phase. In massive MIMO, the full CSI feedback data is of large size and is resource-intensive to process, making it challenging to implement efficiently. RSRP alone for a stand-alone base station is not a good marker of the position of a receiver. Hence, in this work, uplink CSI estimated at the base station along with feedback of RSRP and binary acknowledgment of the accuracy of received data is utilized to design the beamforming codebook at the base station. Simulations using sub-array antenna and ray-tracing channel demonstrate the proposed system’s ability to learn topography-aware beam codebook for arbitrary beams serving multiple user groups simultaneously. The proposed method extends beyond mono-lobe and fixed beam architectures by dynamically adapting arbitrary shaped beams to avoid inter-beam interference, enhancing overall system performance. This work leverages MARL’s potential in creating efficient beam codebooks for hybrid MIMO systems, paving the way for enhanced multiuser communication in future wireless networks.

Unmanned Aerial Vehicles (UAVs) have become increasingly important in various applications, including environmental monitoring, disaster response, and surveillance, due to their flexibility, efficiency, and ability to access hard-to-reach areas. Effective path planning for multiple UAVs exploring a target area is crucial for maximizing coverage and operational efficiency. This study presents a novel approach to optimizing collaborative navigation for UAVs using Multi-Agent Reinforcement Learning (MARL). To enhance the efficiency of this process, we introduce the Adaptive Dimensionality Reduction (ADR) framework, which includes Autoencoders (AEs) and Principal Component Analysis (PCA) for dimensionality reduction and feature extraction. The ADR framework significantly reduces computational complexity by simplifying high-dimensional state spaces while preserving crucial information. Additionally, we incorporate communication modules to facilitate inter-UAV coordination, further improving path planning efficiency. Our experimental results demonstrate that the proposed approach significantly enhances exploration performance and reduces computational complexity, showcasing the potential of combining MARL with ADR techniques for advanced UAV navigation in complex environments.

This paper presents an innovative multi-agent, data-driven reinforcement learning (RL) approach to develop and utilize the thermal equivalent network model that represents the motor's thermal dynamics. A multi-agent reinforcement learning is designed and trained to adjust the model parameters using data from several motor driving cycles. To ensure the incoming driving cycle matches the historical data before employing the pre-trained RL agents, offline statistical analysis and clustering techniques are developed and used. Numerical simulations highlighted the RL agent's ability to develop strategies that effectively address the variability of driving cycles. The proposed RL framework showed its capability to accurately reflect the motor's thermal behavior under various driving conditions.

The studied solar pot is a recent invention, which gained a utility model protection in 2021 from the Hungarian Intellectual Property Office under patent number 5489. The device is made for environmentally friendly cooking or heating (by utilizing solar energy) of foods and liquids. Its structure is similar to a double pipe heat exchanger, it has an outer mantle and an inner cooking tank. The goals of the paper are proposing a new physically-based mathematical model describing the solar pot and carrying out computer experiments with it, assembling an experimental system of the pot connected with a solar collector and performing measurements on it. Based on the results, the solar pot can successfully be used for cooking or sterilizing foods or liquids during the studied time period, in Hungary.

Berberis vulgaris L. (Berberidaceae) is a shrub that has been widely used in European folk medicine as an anti-inflammatory and antimicrobial agent. The purpose of our study was to elucidate the mechanisms of antiproliferative action of the plant’s methanolic root extract (BVR) against colon cancer cells. Cytotoxicity and pro-apoptotic activity were determined in human colon adenocarcinoma cell lines (LS180 and HT-29) and control colon epithelial CCD841 CoN cells. According to the MTT assay, after 48 h of cell exposure, the IC50 values were as follows: 4.3; 46.1 and 50.2 µg/mL for LS180, HT-29, and CCD841 CoN cells, respectively, showing the greater sensitivity of cancer cells to BVR. The Cell Death Detection ELISAPLUS kit demonstrated that BVR induced programmed cell death only against HT-29 cells. RT-qPCR with relative quantification method showed significant changes in the expression of genes related to apoptosis in both colon cancer cell lines. The genes BCL2L1 (126.84-366.66%), BCL2L2 (277.08-330.12%), CASP3 (180.36-261.36%) and CASP9 (158.08-213.46%) had significantly elevated expression, while BCL2 (23.08-52.06%) had reduced expression. Furthermore, in a panel of antioxidant tests, BVR showed positive effects (63.93±0.01, 122.92±0.01, and 220.29±0.02 mg Trolox equivalents (TE)/g in the DPPH•, ABTS•+ and ORAC assays, respectively). In the lipoxygenase (LOX) inhibition test, BVR revealed 62,60±0.87% of enzyme inhibition. The chemical composition of BVR was determined using UHPLC-UV-CAD-MS/MS analysis and confirmed the presence of several known alkaloids, including berberine, as well as other alkaloids and two derivatives of hydroxycinnamic acid (ferulic and sinapic acid hexosides). This is the first such extensive assessment of the biological activity of BVR. The results are very promising and encourage for the use of BVR as a comprehensive chemopreventive agent (anti-inflammatory, antioxidant, and pro-apoptotic) in colorectal cancer.

In this paper, we unite concepts from Husserlian phenomenology, the active inference framework in theoretical biology, and category theory in mathematics to develop a comprehensive framework for understanding social action premised on shared goals. We begin with an overview of Husserlian phenomenology, focusing on aspects of inner time consciousness, namely, retention, primal impression, and protention. We then review active inference as a formal approach to modeling agent behavior, based on variational (approximate Bayesian) inference. Expanding upon Husserl’s model of time consciousness, we consider collective goal-directed behavior, emphasizing shared protentions among agents and their connection to the shared generative models of active inference. This integrated framework aims to formalize shared goals in terms of shared protentions, and to thereby shed light on the emergence of group intentionality. Building on this foundation, we incorporate mathematical tools from category theory; particularly, sheaf and topos theory, to furnish a mathematical image of individual and group interactions within a stochastic environment. Specifically, we employ morphisms between polynomial representations of individual agent models, allowing predictions not only of their own behaviors but also those of other agents and environmental responses. Sheaf and topos theory facilitate the construction of coherent agent worldviews and provides a way of representing consensus or shared understanding. We explore the emergence of shared protentions, bridging the phenomenology of temporal structure, multi-agent active inference systems, and category theory. Shared protentions are highlighted as pivotal for coordination and achieving common objectives. We conclude by acknowledging the intricacies stemming from stochastic systems and uncertainties in realizing shared goals.

Lap joints were friction stir welded in AA 7075-T6 at 1320 rpm and using two welding speeds: 70 mm/min and 120 mm/min. The temperature profiles of the weld zone were registered during the process; furthermore, the microhardness, tensile strength, and microstructure of the joints produced were examined. This study brings new insights into the thermomechanical behavior of the material during the process. The peak temperature obtained with the lower welding speed (70 mm/min) is 10% higher than that obtained with the higher speed (120 mm/min). Moreover, a 5% increase in microhardness and a 6% increase in tensile strength were were observed increasing the welding speed. Addition-ally, the microstructure examination demonstrated that, by decreasing the welding speed, the larger interaction between the tool and the material results in a deeper stir zone due to the increased heat diffusion downwards to the material. This heat flow affects the thermal profile and influences the resulting mechanical properties of the welded joints.

Device to Device (D2D) is a pivotal technology in the next generation of communication, allowing for direct task offloading between mobile devices (MDs) to improve the efficient utilization of idle resources. This paper proposes a novel algorithm for dynamic task offloading between active MDs and idle MDs in the D2D-MEC (Mobile Edge Computing) system by deploying multi-agent deep reinforcement learning (DRL) to minimize the long-term average delay of delay-sensitive tasks under deadline constraints. Our core innovation is a dynamic partitioning scheme for idle and active devices in the D2D-MEC system, accounting for stochastic task arrivals and multi-time-slot task execution, which has been insufficiently addressed in existing literature. We adopt a queue-based system to formulate a dynamic task offloading optimization problem. To address the challenges of large action space and coupling of actions across time slots, we model the problem as a Markov Decision Process (MDP) and perform the multi-agent DRL through Multi-Agent Proximal Policy Optimization (MAPPO). We employ a centralized training with decentralized execution (CTDE) framework to enable each MD to make offloading decisions solely based on its local system state. Extensive simulations demonstrate the efficiency and fast convergence of our algorithm. In comparison with the existing sub-optimal results deploying single-agent DRL, our algorithm reduces the average task completion delay by 11.0% and the ratio of dropped tasks by 17.0%.

The multi-UAV target search problem is crucial in the field of autonomous Unmanned Aerial Vehicle (UAV) decision-making. The algorithm design of Multi-agent Reinforcement Learning (MARL) methods has become integral to research on multi-UAV target search, due to its adaptability to the rapid online decision-making required by UAVs in complex, uncertain environments. In non-cooperative target search scenarios, targets may have the ability to escape, complicating UAVs' search efforts and hindering the convergence of the MARL algorithm training. This paper investigates the multi-UAV target search problem in scenarios involving static obstacles and dynamic escape targets, modeling the problem within the framework of Decentralized Partially Observable Markov Decision Process. Based on this model, a Spatio-Temporal Efficient Exploration network and a Global Convolutional Local Ascent mechanism are proposed. Subsequently,we introduce a Multi-UAV Escape Target Search Algorithm Based on MAPPO(ETS-MAPPO) for addressing the escape target search difficulty problem. Simulation results demonstrate that the ETS-MAPPO algorithm outperforms five classical MARL algorithms in terms of the number of target searches,the area coverage rate, and other metrics.

The PLM concept implies the use of heterogeneous information resources at different stages of the product life cycle, the joint work of which allows you to effectively solve the problems of product quality and various costs. According to the principle of isomorphism of regularities of complex systems, an effective PLM system must have these regularities. Unfortunately, this principle is not often fundamental when designing PLM systems. The purpose of the work is to show, using a simple example, the principles of development, operation and use of an educational multi-agent PLM system, the main purpose of which is to study and research these regularities in the life cycle of a special threaded connection. The multi-agent approach to the development of a PLM system provides the necessary prerequisites for the emergence of system-wide regularities in it. The parallel work of agents is implemented using the actor model and the Ray Python-package. Agents for the logical inference of knowledge base facts, CAD/FEA/CAM/SCADA agents, agents for optimization by various methods, and other agents have been developed. Open source software was used to develop the system. Each agent has relatively simple behavior, implemented by its rule function, and can interact with other agents. The system can work in interactive mode with the user or in automatic mode according to a simple algorithm: the rule functions of all agents are executed until at least one of them returns a value other than None. Examples of the operation of the system are given and such system-wide regularities as emergence, historicity and self-organization are demonstrated in it.

The normal growth and development of skeletal muscle is essential for the health of the body. The regulation of skeletal muscle by intestinal microorganisms and their metabolites has been continuously revealed. Acetate is the predominant short-chain fatty acid synthesized by gut microbiota through the fermentation of dietary fiber, however, the underlying molecular mechanisms governing the interaction between acetate and skeletal muscle during rapid growth stage remain to be further elucidated; Here, specific pathogen-free (SPF) mice, germ-free (GF) mice, and germ-free mice supplemented with sodium acetate (GS) were used to evaluate the effects of acetate on skeletal muscle growth and development of young mice with gut microbiota deficiency; We found the concentration of serum acetate, body mass gain, succinate dehydrogenase activity and expression of myogenesis maker gene of skeletal muscle in the GS group was higher than GF group following sodium acetate supplement. Furthermore, the transcriptome analysis revealed that acetate activated biological processes regulating skeletal muscle growth and development in GF group that are inhibited due to gut microbiota deficiency. In vitro experiment, we proved that acetate up-regulated Gm16062 to promote skeletal muscle cell differentiation; Overall, our findings proved that acetate promote skeletal muscle growth and development in young mice via increase Gm16062 expression.

Background. We created agent-based model for short- and longterm forecasting of COVID-19 and for evaluation how the actions of the regulator affected the human and material resources of the healthcare system. Methods. The model was implemented in the AnyLogic software. It includes two state charts – social network and disease transmission. The COVID-19 Essential Supplies Forecasting Tool (COVID-ESFT, version 2.0) was used to determine healthcare resources needed. Results. Satisfactory results were obtained with long-term (up to 50 days) forecasting in the case of a monotonous change in total cases curve. However, if periods of relative stability are accompanied by sudden outbreaks, relatively satisfactory results were obtained with short-term forecasting, up to 10 days. Simulation of various scenarios showed that the most important place for the spread of infection are families. Wherein the maximum number of cases of COVID-19 is observed in the age group of 26-59 years. Due to a set of measures taken by government agencies, the number of cases in Karaganda city was 3.2 times less than was predicted in “no intervention” scenario. Economic effect is estimated at 40 %. Conclusion. Performed model is an attempt to consider as much as possible the peculiarities of the socio-demographic situation in the country. In the future, we will be prepared to some extent for challenges like those we have experienced in the past three years.

In this paper, we propose, implement, and test two novel downlink LTE scheduling algorithms. The implementation and testing of these algorithms were in Matlab, and they are based on the use of Reinforcement Learning, more specifically, the Qlearning technique for scheduling two types of users. The first algorithm is called a Collaborative scheduling algorithm, and the second algorithm is called a Competitive scheduling algorithm. The first type of the scheduled users is the Primary Users, and they are the licensed subscribers that pay for their service. The second type of the scheduled users is the Secondary Users, and they could be unlicensed subscribers that dont pay for their service, device to device communications, or sensors. Each user whether it is a primary or secondary is considered as an agent. In the Collaborative scheduling algorithm, the primary user agents will collaborate in order to make a joint scheduling decision about allocating the resource blocks to each one of them, then the secondary user agents will compete among themselves to use the remaining resource blocks. In the Competitive scheduling algorithm, the primary user agents will compete among themselves over the available resources, then the secondary user agents will compete among themselves over the remaining resources. Experimental results show that both scheduling algorithms converged to almost ninety percent utilization of the spectrum, and provided fair shares of the spectrum among users.

There is an increased interest in the district-scale energy transition within interdisciplinary research community. Agent-based modelling presents a suitable approach to address variety of questions related to policies, technologies, processes, and the different stakeholder roles that can foster such transition. This state-of-the-art review focuses on the application of agent-based modelling for exploring policy interventions that facilitate the decarbonisation (i.e., energy transition) of districts and neighbourhoods while considering stakeholders’ social characteristics and interactions. We systematically select and analyse peer-reviewed literature and discuss the key modelling aspects, such as model purpose, agents and decision-making logic, spatial and temporal aspects, and empirical grounding. The analysis reveals that the most established agent-based models’ focus on innovation diffusion (e.g., adoption of solar panels) and dissemination of energy-saving behaviour among a group of buildings in urban areas. We see a considerable gap in exploring the decisions and interactions of agents other than residential households, such as commercial and even industrial energy consumers (and prosumers). Moreover, measures such as building retrofits and conversion to district energy systems involve many stakeholders and complex interactions between them that up to now have hardly been represented in the agent-based modelling environment.

This investigation explores a novel path-planning and optimization strategy for multiple cooperative robotic agents, applied in a fully observable and dynamically changing obstacle field. Current dynamic path planning strategies employ static algorithms operating over incremental time-steps. We propose a cooperative multi-agent (CMA) based algorithm, based on natural flocking of animals, using vector operations. It is preferred over more common graph search algorithms like A* as it can be easily applied for dynamic environments. CMA algorithm executes obstacle avoidance using static potential fields around obstacles, that scale based on relative motion. Optimization strategies including interpolation and Bezier curves are applied to the algorithm. To validate effectiveness, CMA algorithm is compared with A* using static obstacles due to lack of equivalent algorithms for dynamic environments. CMA performed comparably to A* with difference ranging from -0.2% to 1.3%. CMA algorithm is applied experimentally to achieve comparable performance, with an error range of -0.5% to 5.2%. These errors are attributed to the limitations of the Kinect V1 sensor used for obstacle detection. The algorithm was finally implemented in a 3D simulated space, indicating that it is possible to apply with drones. This algorithm shows promise for application in warehouse and inventory automation, especially when the workspace is observable.

In this paper, modelling, simulation and verification of multi-agent manufacturing system with application of bio-inspired techniques are addressed. To this end, the new solution of abstract architecture for control and coordination decentralized systems - CODESA is suggested. Centralized architecture suffers from various problems, such as rigidity, scalability, low fault-tolerance or very limited flexibility, agility, energy efficiency and productivity. Prime is concrete application of CODESA in manufacturing domain. The undesirable characteristics of emergent behaviour are the problem to achieve optimization and impossibility to predict future states of the system. CODESA-Prime has been tested by simulations for automatic guided vehicle (AGV) systems guided by magnetic tape in Ella Software Platform.

In this work, we propose a self-supervised multi-agent system that meets the online learning of clustering tasks for video behavior recognition spatio-temporal tasks. Encoding visual behavioral actions as discrete temporal sequence(DTS). Real-time clustering recognition task in a multi-agent system for continuous model building, training, and correction. Finally, we implemented a fully decentralized multi-agent system and completed its feasibility verification in a surveillance video application scenario on vehicle path clustering.

For the task planning problem of the command and control architecture, the existing algorithms have problems such as low efficiency and poor re-planning quality under abnormal conditions. Based on the requirements of the current accusation architecture, this paper constructs a distributed command and control architecture model based on multi-agents, which makes use of the superiority of multi-agents in dealing with complex tasks. The concept of MultiAgents-HTN is proposed under the framework. The original hierarchical task network planning algorithm is optimized, the multi-agent collaboration framework is redefined, and the coordination mechanism of local conflict is designed. Taking the classical resource scheduling problem as the experimental background, the comparison between the proposed algorithm and the classical HTN algorithm is carried out. The experimental results show that the proposed algorithm has higher quality and higher efficiency than the existing algorithm, and the space anomaly is heavy during processing. The planning is more efficient, and the time is more complicated and superior in dealing with the same problem, with good convergence and adaptability. The conclusion proves that the distributed command and control architecture proposed in this paper has high practicability in related fields and can solve the problem of distributed command and control architecture in multi-agent environment.

Despite being stored at 113 K and atmospheric pressure, LNG cold potential is not exploited to reduce green ships’ energy needs. An innovative system based on three Organic Ranking Cycles integrated into the regasification equipment is proposed to produce additional power and recover cooling energy from condensers. A first-law analysis identified ethylene and ethane as suitable working fluids for the first and the second ORC making available freshwater and ice. Propane, ammonia and propylene could be arbitrarily employed in the third ORC for air-conditioning. An environmental analysis that combines exergy efficiency, ecological indices and hazard aspects for marine environment and ship’s passengers, indicated propylene as safer and more environmentally friendly. The exergy analysis confirms more than 20% of the LNG potential can be recovered from every cycle to produce a net clean power of 76 kW, whereas 270 kW can be saved by recovering condensers' cooling power to satisfy some ship needs. Assuming the sailing mode, a limitation of 162 kg in LNG consumptions was determined, avoiding the emission of 1584 kg of CO2 per day. Marine thermal pollution is reduced by 3.5 times by recovering the working fluids' condensation heat for the LNG pre-heating.

This article focuses on the leader-following consensus of fuzzy fractional order singular perturbation multi-agent systems (FOSPMASs) with order in 0,2. By employing the T-S fuzzy modeling approach, a fuzzy FOSPMAS is constructed. Subsequently, a fuzzy observer-based controller is designed and the error system corresponding to each agent is derived. Through a series of equivalent transformations, the error system is decomposed into fuzzy singular fractional order systems (SFOSs). According to the admissibility of SFOSs, the consensus conditions of the fuzzy FOSPMAS are obtained based on linear matrix inequalities (LMIs) without equality constraint. Finally, the effectiveness of the criteria is verified through an RLC circuit model.

Video behavior recognition often needs to focus on object motion processes. In this work, a self-organizing computational system oriented to behavioral clustering recognition is proposed, which achieves the extraction of motion change patterns by binary encoding and completes motion pattern summarization using a similarity comparison algorithm. And in the face of unknown behavioral video data, a self-organizing structure with layer-by-layer accuracy progression is used to achieve motion law summarization by using a multi-layer agent design approach. Finally, the real-time feasibility is verified in the prototype system using real scenes to provide a new feasible solution for unsupervised behavior recognition and space-time scenes.

Accurate localization of road agents is the basis of intelligent transportation systems, which is still difficult to achieve for GNSS positioning in urban areas due to the signal interferences from buildings. Various collaborative positioning techniques are recently developed to improve the positioning performance by the aid from neighboring agents. However, it is still challenging to study their performances comprehensively. The GNSS measurement error behavior is complicated in urban areas and unable to be represented by naive models. On the other hand, real experiment requiring numbers of devices is hard to be conducted, especially for a large-scale test. Therefore, a GNSS realistic urban measurement simulator is developed to provide measurements for collaborative positioning studies. The proposed simulator employs a ray-tracing technique searching for all possible interferences in the urban area. Then, it categorizes them into direct, reflected, diffracted, and multipath signal to simulate the pseudorange, carrier-phase, 〖C/N〗_0, and Doppler shift measurements correspondingly. The performance of the proposed simulator is validated through real experimental comparisons with different scenarios. The proposed simulator is also applied with different positioning algorithms, which verifies it is sophisticated enough for the collaborative positioning studies in the urban area.

This paper investigates the energy dissipation level of a nonlinear vehicle suspension system. The suspension system is modelled as a mass-spring-damper system, which is designed using the output frequency response function (OFRF) method. This method enables the derivation of an explicit relationship, between the system output spectrum (or Performance metric) and the system nonlinear parameters of interest. The OFRF polynomial, of the energy dissipation level, was derived in terms of the nonlinear parameters of interest. The results obtained show that the OFRF model, of the energy dissipation level, could be used to estimate the amount of heat dissipated, for a set of design parameters. This has potentials of providing some insights, in the design of vibration-based energy harvesters, as some of the wasted heat energy could be converted to electrical energy.

Systems Engineering is an ubiquitous discipline of Engineering overlapping industrial, chemical, mechanical, manufacturing, control, software, electrical, and civil engineering. It provides tools for dealing with the complexity and dynamics related to the optimisation of physical, natural, and virtual systems management. This paper presents a review of how multi-agent systems and complex networks theory are brought together to address Systems Engineering and management problems. The review also encompasses current and future research directions both for theoretical fundamentals and applications in Industry. This is made by considering trends such as mesoscale, multiscale, and multilayer networks; along with the state-of-art analysis on network dynamics and intelligent networks. Critical and smart infrastructure, manufacturing processes, and supply chain networks are instances of research topics for which this literature review is highly relevant.

This review summarises the main numerical models of fuel droplet heating and evaporation (DHE) in combustion engines across the different scales by accessing the nano/micro, meso and macroscopic fluid elements. The phenomena of multi-physics, multi-scale and multi-phase fluid flow and heat transfer are fully investigated when the fuel droplet (dodecane) is heating and evaporated into a background gas (nitrogen) crossing the liquid-vapour (LV) interface, kinetic region (i.e., Knudsen layer) and the bulk regions of liquid and gas in terms of molecular dynamics (MD) simulations, kinetic theory modelling (i.e., direct numerical solutions of Boltzmann equations) and convectional fluid dynamics approach, respectively. The evaporation coefficient of fuel evaporating molecules and their velocity distributions at the LV interface derived from MD simulations formulate a new kinetic boundary condition (KBC). Moreover, a novel kinetic model considering the inelastic collision between fuel molecules alongside the new KBC enables us to describe the non-equilibrium gas dynamics of fuel vapour and gas mixture in Knudsen layer (KL). Heat and mass flux analysis of the fuel droplet under combustion engine conditions can be accurately assessed by implementing the inelastic collision between fuel molecules in KL and a temperature-dependent evaporation coefficient at the LV interface into DHE. The surface temperature of fuel droplet and its evaporation time, which play a significant role in resolving the ignition delay and hence the combustion phasing in engines, can also be well estimated. The multi-scale modelling of fuel DHE will make significantly potential input into the cleaner engine targeting the low-carbon emissions and enhance the capability of the existing computational fluid dynamics (CFD) solvers.

The polarised emission from AGN jets carries information about the physical conditions at the emitting plasma elements while its temporal evolution probes the physical processes that introduce variability and dynamically modify the local conditions. Here we present the analysis of multi-frequency radio linear and circular polarisation datasets with the aim to exactly quantify the conditions in blazar jets. Our analysis includes both the careful treatment of observational datasets and numerical modelling for the reproduction of synthetic polarisation curves that can be compared to the observed ones. In our approach the variability is attributed to traveling shocks. The emission from the cells of our jet model is computed with radiative transfer of all Stokes parameters. The model also accounts for Faraday effects which map the low-energy particle populations. We present two extreme cases in terms of the significance of Faraday conversion in the production of circular polarisation. As we show, in both regimes the model gives realistic reproduction of the observed emission.

In recent years, the viability of employing multi-agent reinforcement learning technology for adaptive traffic signal control has been extensively validated. However, owing to restricted communication among agents and the partial observability of the traffic environment, the process of mapping road network states to actions encounters numerous challenges. To address this problem, this paper proposes a multi-agent deep reinforcement learning model with an emphasis on communication content (CMARL). The model decouples the complex relationships between multi-signal agents through centralized training and decentralized execution. Specifically, we first pass the traffic state through an improved deep neural network to achieve the extraction of high-dimensional semantic information and the learning of the communication matrix. Then the agents selectively interact with each other based on the learned communication matrix and generate the final state features. Finally, the features are inputted to the QMIX network to achieve the final action selection. We compare the CMARL model with 6 other baseline algorithms in real traffic networks. The results show that CMARL can significantly reduce vehicle congestion, and run stably in various scenarios.

The Bayes filters, such as Kalman and particle filters, have been used in sensor fusion to integrate two sources of information and obtain the best estimate of the unknowns. Efficient integration of multiple sensors requires deep knowledge of their error sources and it is not trivial for complicated sensors, such as Inertial Measurement Unit (IMU). Therefore, IMU error modelling and efficient integration of IMU and Global Navigation Satellite System (GNSS) observations has remained a challenge. In this paper, we develop deep Kalman filter to model and remove IMU errors and consequently, improve the accuracy of IMU positioning. In other words, we add modelling step to the prediction and update steps of Kalman filter and the IMU error model is learned during integration. Therefore, our deep Kalman filter outperforms Kalman filter and reaches higher accuracy.

This paper presents MADS (Multi-Agents for Data Science), an innovative and simple open-source multi-agent framework designed for systemic pipeline execution in applied supervised machine learning. By leveraging the capabilities of multi-agent systems (MAS), we introduce a universal approach to optimize and streamline machine learning pipelines. Our framework highlights the differences between various types of agents, such as reinforcement learning (RL) agents and large language model (LLM) agents, and their distinct contributions to the process. While we currently employ LLM agents to automate and enhance machine learning tasks, we acknowledge the potential of incorporating RL agents in future iterations to further improve performance and adaptability. The primary objective is to enhance the efficiency, scalability, and adaptability of supervised learning applications across various domains. This integration addresses the complexity and manual effort typically associated with machine learning workflows, paving the way for more automated, robust, and scalable solutions. Our approach demonstrates significant improvements in task automation, reduced human intervention, and enhanced model performance. The MADS framework, which will soon be available as an open-source implementation, represents a pivotal contribution to the field of machine learning, promising to facilitate broader adoption and collaborative advancement.

This paper extends the concept of weighted graphs to matrix weighted graphs. The consensus algorithms dictate that all agents reach consensus when the weighted graph is connected. However, it is not always the case for matrix weighted graphs. The conditions leading to different types of consensus have been extensively analysed based on the properties of matrix-weighted Laplacians and graph theoretic methods. However, in practice, there is concern on how to pick matrix-weights to achieve some desired consensus, or how the change of elements in matrix weights affects the consensus algorithm. By selecting the elements in the matrix weights, different clusters may be possible. In this paper, we map the roles of the elements of the matrix weights in the systems consensus algorithm. We explore the choice of matrix weights to achieve different types of consensus and clustering. Our results are demonstrated on a network of three agents where each agent has three states.

We evaluated performance of two American surveillance systems for monitoring the spread of antimicrobial-resistant (AMR) gonorrhea: the Gonococcal Isolate Surveillance Project (GISP) and the enhanced Gonococcal Isolate Surveillance Project (eGISP) which includes the non-urethral isolates in addition to the urethral ones utilized in the original surveillance system. A continuous-time agent-based model of gonorrhea transmission among the US men who have sex with men (MSM) population was developed and used for this purpose. The model accounts for susceptible and resistant strains of N. gonorrhoeae, symptomatic and asymptomatic infection and different transmission routes. Overall, eGISP system outperforms the original GISP system and allows to obtain a higher accuracy using a significantly lower number of isolates. Most of time, the original surveillance system determines the moment of switch to a new antibiotic later than necessary which leads to additional gonorrhea cases and spread of the resistance. Informing the gonorrhea treatment guidelines by eGISP estimates instead of the currently used GISP estimates would result in reduction of 622 (95% uncertainty interval: -4,009, 9,099) gonorrhea cases in the simulated cohort of 10,000 US MSM over a 25-year period without reduction in the lifespan of the current first-line antibiotic.

: Multimodal Large Language Models (MLLMs) harness comprehensive knowledge spanning text, images, and audio to adeptly tackle complex problems, including zero-shot in-context learning scenarios. This study explores the ability of MLLMs in visually solving the Traveling Salesman Problem (TSP) and Multiple Traveling Salesman Problem (mTSP) using images that portray point distributions on a two-dimensional plane. We introduce a novel approach employing multiple specialized agents within the MLLM framework, each dedicated to optimizing solutions for these combinatorial challenges. Our experimental investigation includes rigorous evaluations across zero-shot settings and introduces innovative multi-agent zero-shot in-context scenarios. The re-sults demonstrated that both multi-agent models—Multi-Agent 1, which includes the Initializer, Critic, and Scorer agents, and Multi-Agent 2, which comprises only the Initializer and Critic agents—significantly improved solution quality for TSP and mTSP problems. Multi-Agent 1 ex-celled in environments requiring detailed route refinement and evaluation, providing a robust framework for sophisticated optimizations. In contrast, Multi-Agent 2, focusing on iterative re-finements by the Initializer and Critic, proved effective for rapid decision-making scenarios. These experiments yield promising outcomes, showcasing the robust visual reasoning capabilities of MLLMs in addressing diverse combinatorial problems. The findings underscore the potential of MLLMs as powerful tools in computational optimization, offering insights that could inspire further advancements in this promising field.

When wildlife and motor vehicles collide, the result for the animals is often death (roadkill). A commercial roadkill Virtual Fence (VF) mitigation device (iPTE Traffic Solutions) was used in a field trial to test its effectiveness along a 4.9-km segment of road on Bruny Island, Tasmania. A total of 585 days of monitoring of roadkill by species was conducted, with six sections alternatively switched on or off, according to a variation of a Crossover and Multiple Before-After-Control-Impact (MBACI) experimental designs that divided monitoring into “off-on” then “on-off” blocks of periods with each “on” period followed by a 16 d “wash-out” period. For the six sections over the four periods that exclude wash-outs, the 24 aggregated values of daily counts of roadkill of Tasmanian pademelons (Thylogale billardierii), that gave a total count of 222, were modelled. Other species were killed in insufficient numbers for analysis to be informative. The statistical analysis exploited the MBACI design to estimate the VF effect using a log-odds ratio parameter (LORP) while accounting for local spatio-temporal effects. Both versions of the analysis, either averaging over the three spatial replicates (paired sections) or two temporal replicates (blocks) gave no statistically significant effect of the VF judged as a LORP estimate not sufficiently below zero. Corresponding percentage reduction estimates of 9% and 16% were derived from the LORP estimates and given parameter uncertainty estimates the power to detect as significant a LORP corresponding to a 50% reduction in rate were 0.5 and 0.6, respectively. This study confirms results from a similar field trial carried out in 2018 also in southern Tasmania and adds to the evidence that this VF is likely to give if anything only a minor reduction in roadkill for a commonly killed species for which researchers have the best chance of detecting any practically useful reduction.

The anti-money laundering (AML) process has failed both in identifying suspicious cases in due time as in assisting the AML analysts in decision making. Starting from a new generic anti-fraud approach, this article presents the main aspects related to the development of a multi-agent system that goes beyond the capture of suspicious transactions, seeking to assist the human expert in the analysis of suspicious behaviour. First, a transactional behavioural profile of clients is obtained in a data mining process. A set of rules, obtained through data mining over a real database, in conjunction with specific rules based on legal aspects and in the expertise of the AML analysts make up the agents' knowledge base. The cases for which the system was unable to suggest a decision are flagged as requiring more detailed analysis. The system analysed 6 months of real transactions and indicated several suspicious profiles, a set of these suspects was investigated by the AML analysts who proved the suspicion of several cases, including some that had not been identified by the systems in execution.

The objective of this paper was to verify the applicability of statistical learning (SL) compared to human reasoning with respect to the Universal Thermal Climate Index (UTCI), a complex tool for the assessment of outdoor thermal stress. UTCI is an equivalent temperature index based on the 48-dimensional output of an advanced model of human thermoregulation formed by 12 variables at four consecutive 30-minute intervals, which were calculated for 105642 thermal conditions from extreme cold to extreme heat. Comparing the performance of SL algorithms to the results accomplished by an international endeavor involving more than 40 experts from 23 countries, we found that random forests and k-nearest neighbors closely predicted UTCI values, but that clustering applied after dimension reduction algorithms (principal component analysis and t-distributed stochastic neighbor embedding) were inadequate for risk assessment in relation to the UTCI stress categories. This indicates a potential supportive role for SL, as it will not (yet) fully replace the bio-meteorological expert knowledge.

Insulin-like Growth Factor 2 mRNA binding Protein 1 (IGF2BP1) is a promising candidate gene for influencing economic traits in livestock and poultry. The second intronic region of IGF2BP1 is closely related to growth traits, although the exact mechanism remains unclear. The preliminary resequencing results of goats in our laboratory demonstrated that the IGF2BP1 gene region was subject to strong selection, then we selected multiple single nucleotide polymorphisms (SNPs) to identify. Seven SNPs were located in the conserved region of the second intron, and their functions and relationship with growth traits require further clarification. This study selected 348 Nanjiang Yellow goats as experimental subjects, and chose Time of Flight Mass Spectrometer (MALDI-TOF) as the main method. Our results showed that six SNPs were significantly correlated with the growth traits of the Nanjiang yellow goat by association analysis. Among them, the rs652062749(A>G) was identified as the primary locus affecting the later stage of growth traits of Nanjiang yellow goat. Moreover, there was a strong linkage among three SNPs, and the rs638185407 (T>A) mutant type was observed to increase the luciferase activity in H293T cells extremely significantly. The TTAACT, TTCCCC, and ATCACT combination genotypes were dominant combination genotypes, which provided theoretical references for further genetic co-breeding. The results of our study demonstrate the potential role of the IGF2BP1 gene as a functional genetic marker in the breeding programs of Nanjiang Yellow goats.

Titanium dioxide nanoparticles have risen concerns about their possible toxicity and the European Food Safety Authority recently banned the use of TiO2 nano-additive in food products. Following the intent of relating nanomaterials atomic structure with their toxicity without having to conduct large scale experiments on living organisms, we investigate the aggregation of titanium dioxide nanoparticles using a multi-scale technique: starting from ab initio Density Functional Theory to get an accurate determination of the energetics and electronic structure, we switch to classical Molecular Dynamics simulations to calculate the Potential of Mean Force for the connection of two identical nanoparticles in water; the fitting of the latter by a set of mathematical equations is the key for the upscale. Lastly, we perform Brownian Dynamics simulations where each nanoparticle is a spherical bead. This coarsening strategy allows studying the aggregation of a few thousand nanoparticles. Applying this novel procedure, we find three new molecular descriptors, namely, the aggregation free energy and two numerical parameters used to correct the observed deviation from the aggregation kinetic described by the Smoluchowski theory. Molecular descriptors can be fed into QSAR models to predict the toxicity of a material knowing its physicochemical properties, without having to conduct large scale experiments on living organisms.

Abstract: The diffusion of competition under the coexistence of multi-generation products has become one of the important challenges faced by enterprises in their daily and sustainable operations. At the same time, the competition between different brands has intensified the difficulty and complexity of decision-making in the process of multi-generation product operation, Therefore, based on the Norton-Bass model diffusion process, this paper introduces two marketing variables, dynamic price and quality level, builds a multi-generation product diffusion model under the dual-brand competition, and analyzes the impact of the company's revenue on the launch time to market, pricing, quality or technical level. By using system dynamics (SD) method, From the perspective of strong brand and weak brand enterprises, the competition diffusion model is built and simulated. The simulation shows that: i) When enterprises have the same brand competitiveness, reducing the pricing level cannot obtain more revenue, but diminish the overall revenue of the industry; Raising the pricing level can get more revenue, but also improve the revenue of competitors. ii) When the competitive strength of enterprises is different, the strong brand tends to maintain a stable pricing on the basis of improving the quality level, or slightly raise the price. Weak brands tend to raise the pricing of new products significantly on the basis of improving the quality level. iii) The launch time to market decision of new product is influenced by the degree of product quality upgrade. Therefore, the frequency of releasing new products should trade-off against the degree of technological upgrading of product quality. This paper provides the theoretical basis and new insights for the new product launch and operation decision of enterprises.

This paper presents the results of investigations on the kinetic of Brilliant Blue FCF (BB) discoloration reactions in aqueous solutions with different ozone concentrations and pH conditions. Kinetic studies involve knowledge of the structure and properties of the dye and ozone, as well as the experimental conditions. In general, scientists admit that the predominant oxidation pathway is direct (by free oxygen atoms) or indirect (by free hydroxyl radicals), it will depend on influencing factors such as: the physicochemical properties of the dye, the pH of the aqueous solution, ozone concentration, reaction time and the contact mode with/without stirring. In the experimental research, two pathways were chosen following CBB = f(t): 1. constant dye concentration and different ozone concentration on the concentration range (100 - 250 mg/L) at three pH media (acidic, neutral and basic) with and without stirring; 2. Constant concentration of ozone and different dye in the range of concentrations (2.5 - 10 mg/L) under the conditions of point 1. With obtained experimental data the curves CBB = f(t) were drawn and were processed by the integral method of classical kinetic based on first and second order equations. Unfortunately, this simple procedure this not yield any minim full results and any pH level. The rate constants been negative and/or the reaction order been dependent on initial conditions. Due to its structure, the BB dye has several chromophore groups, thus multiple attack centers, resulting in more oxidation by-products, which is why the 1H - NMR spectrum of BB discoloration with ozone was recorded.

The adoption of algorithms based on Artificial Intelligence (AI) has been rapidly increasing during the last years. However, some aspects of AI techniques are under heavy scrutiny. For instance, in many use cases, it is not clear whether the decisions of an algorithm are well-informed and conforming to human understanding. Having ways to address these concerns is crucial in many domains, especially whenever humans and intelligent (physical or virtual) agents must cooperate in a shared environment. In this paper, we introduce an application of an explainability method based on the creation of a Policy Graph (PG) based on discrete predicates that represent and explain a trained agent’s behaviour in a multi-agent cooperative environment. We show that from these policy graphs, policies for surrogate interpretable agents can be automatically generated. These policies can be used to measure the reliability of the explanations enabled by the PGs, through a fair behavioural comparison between the original opaque agent and the surrogate one. The contributions of this paper represent the first application of policy graphs in the context of explaining agent behaviour in collaborative multi-agent scenarios and presents experimental results that sets this kind of scenario apart from previous application in single-agent scenarios: when requiring collaborative behaviour, predicates that allow representing observations about the other agents are crucial to replicate the opaque agent’s behaviour and increase the reliability of explanations.

With the global outbreak of COVID-19, the panic buying incidents triggered by the variants of the Omicron strain have severely affected the normal social order. This paper considers the complex interest game and interactive relationship among multiple subjects in the mass panic buying event caused by rumors and constructs a three-party evolution game model of local government, rumor-monger, and public. Based on the theory of evolution game, the evolutionary process of the strategy selection of game subjects is studied, and the strategy selection of the three-game subjects under different scenarios is compared and analyzed. Taking the example of the montmorillonite powder panic buying caused by the XBB virus strain rumor in China, the evolutionary game model constructed in this study is simulated and analyzed. The study shows that: the evolution process of the mass panic buying event is characterized by six stages: the initial stage E1(0,0,0); the outbreak stage E3(0,1,0);the spread stage E7(0,1,1);the climax stage E8(1,1,1);the relief stage E5(1,1,0);and the recovery stage E4(1,0,0); there are four stable points in the evolutionary game of the three game subjects, namely (no intervention, no rumor, no panic buying), (no intervention, rumor, no panic buying), (intervention, no rumor, no panic buying), and (intervention, rumor, no panic buying), and the strategy of government intervention will be adjusted according to the strategy selection of the public and the rumor-monger; under the mechanism of reward and punishment of the higher-level government, increasing the punishment and reward intensity of the higher-level government will promote the local government to intervene in the rumor-mongering event faster, but increasing the reward intensity has a more significant impact on the intervention behavior of the local government than punishment, and increasing punishment intensity has a more significant impact on the non-rumor-mongering behavior of the rumor-monger than reward; the parameters of social risk-bearing cost, risk transmission coefficient, rumor-mongering income and cost, and public drug purchase cost have different degrees of influence on the evolutionary behavior of game subjects. This study provides new ideas for effectively responding to mass panic buying events in the context of public emergencies.

The glucose-insulin regulatory system and its glucose oscillations is a recurring theme in the literature because of its impact on human lives, mostly the ones affected by diabetes mellitus. Several approaches were proposed, from mathematical to data-based models, with the aim of modeling the glucose oscillation curve. Having such a curve, it is possible to predict, when injecting insulin in type 1 diabetes (T1D) individuals. However, the literature presents prediction horizons no longer than 6 hours, which could be a problem considering their sleeping time. This work presents Tesseratus, a model that adopts a multi-agent approach to combine machine learning and mathematical modeling to predict the glucose oscillation up to 8 hours. Tesseratus uses the pharmacokinetics of insulins and data collected from T1D individuals. Its outcome can support endocrinologists while prescripting daily treatment for T1D individuals, and provide personalized recommendations for such individuals, to keep their glucose concentration in the ideal range. Tesseratus brings pioneering results for prediction horizons of 8 hours for nighttime, in an experiment with seven real T1D individuals. It is our claim that Tesseratus will be a reference for classification of glucose prediction model, supporting the mitigation of short- and long-term complications in the T1D individuals.

The multi-stage, multi-level assembly job shop scheduling problem (MsMlAJSP) is commonly encountered in the manufacturing of complex customized products. Ensuring production efficiency while effectively improving energy utilization is a key focus in the industry. For the energy-efficient MsMlAJSP (EEMsMlAJSP), an improved imperialist competitive algorithm based on Q-learning (IICA-QL) is proposed to minimize the maximum completion time and total energy consumption. In IICA-QL, a decoding strategy with energy-efficient triggers based on problem characteristics is designed to ensure solution quality while effectively enhancing search efficiency. Additionally, an assimilation operation with operator parameter self-adaptation based on Q-learning is devised to overcome the challenge of balancing exploration and exploitation with fixed parameters, thus the convergence and diversity of the algorithmic search is enhanced. Finally, the effectiveness of the energy-efficient strategy decoding trigger mechanism and the operator parameter self-adaptation operation based on Q-learning is demonstrated through experimental results, and the effectiveness of IICA-QL for solving EEMsMlAJSP is verified by comparing with other algorithms.

Risk modelling along with multi-objective optimization problems have been at theepicenter of attention for supply chain managers. In this paper, we introduce a datasetfor risk modelling in sophisticated supply chain networks based on formal mathematical models. We have discussed the methodology and simulation tools used to synthesize the dataset. Additionally, the underlying mathematical models are discussed in granular details along with providing directions to conducting statistical analyses or neural machine learning models. The simulation is performed using MATLAB ™Simulink and the models are illustrated as well.

Waste cooking oil (WCO) recycled asphalt is facing issues regarding insufficient thermal oxidation stability and aging resistance. In this research, glycerol esterification was adopted to pretreat WCO, and the consequences of this treatment on the aging resistance and thermal stability of WCO were analyzed. The impacts of varying levels of esterification of WCO on the high-temperature, low-temperature performances, fatigue properties, as well as aging resistance of recycled asphalt were investigated. Furthermore, the mechanisms of regeneration and anti-aging of deeply esterified WCO recycled asphalt were revealed by Fourier transform infrared spectroscopy (FTIR) and gel permeation chromatography (GPC) tests. The results indicated that variations in the physical properties of WCO during the aging process were reduced, and its aging resistance was improved following glycerol esterification therapy. The initial thermal decomposition temperature was increased by approximately 115°C, which resulted in the enhancement of thermal stability significantly. Recycled asphalt obtained from deeply esterified WCO exhibited superior high-temperature, low-temperature performances and fatigue properties. Moreover, the thermal oxidation stability and aging resistance of recycled asphalt with deep-esterified WCO could be promoted by reducing the oxidation and volatilization of light components during the aging process.

The expansion of renewable energies is progressing strongly. The influence on the power supply networks by the volatility of the infeed must be met with new concepts. In this paper we investigate the possibilities of integrating microgrids as a cooperating unit in the power supply network to support further expansion of RES power plants. In this paper a differentiation of microgrids from similar network structures is established, a classification of proposed groups is made. Then, after the description of simulation of components in a microgrid, with practical advice, an example model is shown, which aids the dimensioning of the components within a microgrid to achieve a specified goal.

There exist numerous high-dimensional problems in the real world which cannot be solved through the common traditional methods. The metaheuristic algorithms have been developed as successful techniques for solving a variety of complex and difficult optimization problems. Notwithstanding their advantages, these algorithms may turn out to have weak points such as lower population diversity and lower convergence rate when facing complex high-dimensional problems. An appropriate approach to solve such problems is to apply multi-agent systems along with the metaheuristic algorithms. The present paper proposes a new approach based on the multi-agent systems and the concept of agent, which is named Multi-Agent Metaheuristic (MAMH) method. In the proposed approach, several basic and powerful metaheuristic algorithms, including Genetic Algorithm (GA), Particle Swarm Optimization (PSO), Artificial Bee Colony (ABC), Firefly Algorithm (FA), Bat Algorithm (BA), Flower Pollination Algorithm (FPA), Gray Wolf Optimizer (GWO), Whale Optimization Algorithm (WOA), Crow Search Algorithm (CSA), Farmland Fertility Algorithm (FFA), are considered as separate agents each of which sought to achieve its own goals while competing and cooperating with others to achieve the common goals. In overall, the proposed method was tested on 32 complex benchmark functions, the results of which indicated effectiveness and powerfulness of the proposed method for solving the high-dimensional optimization problems. In addition, in this paper, the binary version of the proposed approach, called Binary MAMH (BMAMH), was executed on the spam email dataset. According to the results, the proposed method exhibited a higher precision in detection of the spam emails compared to other metaheuristic algorithms and methods.

The Greater Amanzule Peatland (GAP) in Ghana represents an important ecosystem facing dynamic land cover changes as a result of both natural and anthropogenic factors. This study integrates multispectral and radar remote sensing data from Landsat-7 and -8, L-band SAR, and SRTM to conduct a machine learning-based analysis of these changes from 2010 to 2020 and to predict future scenarios up to 2040. Findings reveal a 12% expansion in peatland cover, equivalent to approximately 6,570 ± 308.59 hectares, despite declines in specific peatland types. Concurrently, anthropogenic land uses have increased, evidenced by an 85% rise in rubber plantations (from 30,530 ± 110.96 hectares to 56,617 ± 220.90 hectares) and a 6% reduction in natural forest cover (5,965 ± 353.72 hectares). Sparse vegetation, including smallholder farms, decreased by 35% from 45,064 ± 163.79 hectares to 29,424 ± 114.81 hectares. Projections for 2030 and 2040 indicate minimal changes based on current trends; however, these do not consider potential impacts from climate change, large-scale development projects, and demographic shifts, necessitating cautious interpretation. The results highlight areas of stability and vulnerability within the GAP and offer critical insights for the development of targeted conservation strategies. Additionally, the methodological framework presented provides a robust approach for accurate and detailed landscape-scale monitoring of tropical peatlands, applicable to other regions facing similar environmental challenges.

Lyme disease, the leading vector-borne ailment in the U.S., annually affects an estimated 476,000 individuals, predominantly in the Northeast and Upper Midwest. Despite its increasing incidence, the evaluation of risk within U.S. cities, including natural public lands, remains inadequate. This study focuses on blacklegged tick occurrences and Borrelia burgdorferi infection prevalence in 24 Staten Island parks, aiming to assess Lyme disease exposure risk. Monthly acarological risk index (ARI) calculations from 2019 to 2022 revealed elevated values (0.16-0.53) in specific parks, notably Wolfe’s Pond Park, High Rock Park, Clay Pit Pond Park, Clove Lake Park, and Fair View Park. June (0.36) and November (0.21) consistently exhibited heightened ARIs, aligning with peak tick collection months. Despite stable yearly infection rates at 28.97%, tick densities varied significantly between parks and years. Identifying a high transmission risk in specific parks in Staten Island, a highly urbanized part of New York City, emphasizes the continuous necessity for Lyme disease risk management, even within the greenspaces of large cities.

Manufacturing systems need to meet I4.0 guidelines to deal with uncertainty in scenarios of turbulent demand for products. The engineering concepts to define the service’s resources to manufacture the products will be more flexible, ensuring the possibility of re-planning in operation. These can follow the engineering paradigm based on capabilities. The virtualization of industry components and assets achieves the RAMI 4.0 guidelines and (I4.0C), which describes the Asset Administration Shell (AAS). However, AAS are passive components that provide information about I4.0 assets. The proposal of specific paradigms is exposed for managing these components, as is the case of multi-agent systems (MAS) that attribute intelligence to objects. The implementation of resource coalitions with evolutionary architectures (EAS) applies cooperation and capabilities’ association. Therefore, this work focuses on designing a method for modeling the asset administration shell (AAS) as virtual elements orchestrating intelligent agents (MAS) that attribute cooperation and negotiation through contracts to coalitions based on the engineering capabilities concept. The systematic method suggested in this work is partitioned for the composition of objects, AAS elements, and activities that guarantee the relationship between entities. Finally, Production Flow Schema (PFS) refinements are applied to generate the final Petri net models (PN) and validate them with Snoopy simulations. The results achieved demonstrate the validation of the procedure, eliminating interlocking and enabling liveliness to integrate elements behavior.

The intranasal route of drug administration is characterized by high bioavailability and is considered promising for rapid delivery of drugs with systemic action to the central nervous system, bypassing the blood-brain barrier. This is particularly important for the use of neuroprotective drugs in the treatment of brain tissue damage in infants caused by the effects of intrauterine hypoxia. Creation of new dosage forms for neonatology with the use of software and mathematical technologies in pharmaceutical development allows to create cerebroprotective drugs with controlled pharmaco-technological properties, thus reducing time and resources for necessary research. We developed a formulation of a new nasal gel formulation with Angiolin using Box-Benken experiment design for the therapy of prenatal CNS damage. It was found that the consistency properties of the nasal gel were significantly influenced by the gelling agent and mucoadhesive component - sodium salt of carboxymethylcellulose. We have optimized the composition of nasal gel formulation with Angiolin using the formed models and relationships between the factors. The optimized composition of the obtained nasal gel has satisfactory parameters of thixotropic properties. The developed 1% gel for neuroprotection with Angiolin meets all the requirements for harmlessness and safety to drug forms of this group - low toxicity, absence of local irritant and allergic effect.

The strong competition in the automotive industry has required manufacturers to implement lean production, both with methods and techniques specific to Industry 4.0. At the same time, universities must provide graduates with specific skills for applying these new production methods and techniques. In this context, a Lean Learning Factory was developed in the Pitesti University Center, which allows students to learn, experiment, and research, in an environment similar to that of enterprises, the new Lean Manufacturing methods and techniques, and Industry 4.0. The research presented in this study had as its objective identifying the minimum number of repetitions necessary to train operators who serve two differently organized workstations, one classic, the other including digital techniques, but on which the same assembly operation is performed. Several indicators were considered in the analysis, such as the number of errors, the number of stops, the effective duration of the work cycle, and the percentage ratio between the standard duration of cyclical activities and the effective duration of the work cycle. The evolution of these indicators was mathematically modelled by regression functions, using the least squares method. The obtained results also highlight the usefulness of applying the DOJO method as a Lean manufacturing-specific learning technique and the efficiency of implementing digital techniques in work organization.

Energy consumption modelling is of critical importance for improving energy efficiency in the drive towards sustainable manufacturing. Modern manufacturing processes and machine tools are very complex as they involve interplay of several advanced technologies. Therefore, energy modelling of modern machine tools is a complex multi-disciplinary task. This paper proposes a systematic and practical framework to choose the appropriate modelling approach for a given industrial problem. The framework was validated by applying it to diverse industrial scenarios.

System-of-systems (SoS) evolution is a complex and unpredictable process. Although various principles to facilitate collaborative SoS evolution have been proposed, there is a lack of experimental data validating their effectiveness. To address these issues, we present an Agent-Based Model (ABM) for SoS evolution in the Internet of Vehicles (IoV) , serving as a quantitative analysis tool for SoS research. By integrating multiple complex and rational behaviors of individuals, we aim to simulate real-world scenarios as accurately as possible. To simulate the SoS evolution process, our model employs multiple agents with autonomous interactions and incorporates external environmental variables. Furthermore, we propose three evaluation metrics: evolutionary time, degree of variation, and evolutionary cost, to assess the performance of SoS evolution. Our study demonstrates that enhanced information transparency significantly improves the evolutionary performance of distributed SoS. Conversely, the adoption of uniform standards only brings limited performance enhancement to distributed SoSs. Although our proposed model has limitations, it stands out from other approaches that utilize Agent-Based Modeling to analyze SoS theories. Our model focuses on realistic problem contexts and simulates realistic interaction behaviors. This study enhances the comprehension of SoS evolution processes and provides valuable insights for the formulation of effective evolutionary strategies.

To curb the impacts arising from the agricultural sector the actions undertaken by policymakers, and ultimately by the farmers, are of paramount importance. However, finding the best strategy to reduce impacts, and especially assessing the effects of the interactions and mutual influence among farmers, is very difficult. To this aim, this paper shows an application of an agent-based model (ABM) coupled with life cycle assessment (LCA), which also includes multi objective optimization of farming activities (including both crop cultivation and livestock breeding) from an economic and environmental perspective. The environmental impacts are assessed using the impact assessment scores calculated with the Environmental Footprint (EF) 3.0 life cycle impact assessment (LCIA) method and the study is conducted “from cradle to farm gate”. The model is applied to all the farms in Luxembourg, whose network is constructed utilizing neighborhood interactions, through which a parameter known as farmer's green consciousness (GC) is updated at each time step. The optimization module is instantiated at the end of each time step, and decision variables (the number of livestock units and land allocation) are assigned based on profitability and specified environmental impact categories. If only profit optimization is considered (i.e. when farmers’ GC is de-activated), the results show a 9% reduction in the aggregated environmental impacts (obtained as EF “single score”) and a 5.5% increase in overall profitability. At the farm level, simulations display a clear trade-off between environmental sustainability and financial stability, with a 25% reduction in overall emissions possible if farming activities are carried using the EF single score impact in the objective function, though this results in an 8% reduction in profitability over ten years.

Nowadays, inquiries are one of the most important tasks to be executed in order to get valued information. When an inquiry is done to gather information about a human behavior there are some problems inherent to it. One of the main problems is how the information about many different persons can be processed to give good information about their environment. Most of the information gathered by these inquiries is used to analyze the behavior of the respondents. It can be used to estimate the success of a certain product on the market or just to validate the satisfaction of current costumers. The veracity of this information can be critical to model environments with some acceptable level of precision. Modelling environments through Artificial Neural Networks (ANN) is highly common because ANN’s are excellent to model predictable environments using a set of data. ANN’s are good in deal with sets of data with some noise, but they are fundamentally surjective mathematical functions and they aren’t able to give different results for the same input. So if an ANN is trained using data where the same input has different images which can be the case of survey data, this can be a problem for the success of modelling the environment. Therefore is necessary to process the data in order to adjust and eliminate invalid data.

We are witnessing a progressive divestment of some institutions with strong traditions and skills in physical modelling and their consequent impoverishment, to the detriment of numerical modelling. For many reasons, the economic imperatives and the exponential growth of computational means and numerical methods should certainly not be excluded. In this work, we aimed to highlight the new requirements of the recent sophisticated developments in physical modelling, precisely due to the new needs imposed on them by mathematical and numerical modelling and the growing risks in civil construction works. In this context, reflections are reported, justified by scientific and real-world examples, on the need for maintenance and reinforcement of investments in physical modelling, both to support the scientific community and to design buildings of significant economic, social and environmental impact.

Laser Photoacoustic Spectrometers (LPAS), which provide photoacoustic spectra for detecting food frauds or adulteration, and fluorescence-based systems for recognition of contamination by heavy metal ions in water are two important families of sensors for health and environmental purposes. Both sensor families require one or more low-frequency Lock-In Amplifiers (LIAs) to extract the signal of interest from background noise. In the cited applications, the required LIA frequency is quite low (up to 1kHz), and this leads to a simplification of the hardware with consequent good results in portability, economy, reduced size, weight and low-cost characteristics. The present system, called ENEA DSP Box Due, is based on a very inexpensive microcontroller proto-board and can replace four commercial LIAs, resulting in significant savings in both cost and space. Furthermore, it incorporates a dual-channel oscilloscope and a sinusoidal function generator. This article outlines the architecture of the ENEA DSP Box Due, its electrical characterization and its applications within a project concerning laser techniques for food and water safety.

Background: Breast cancer and other neoplasms, such as acute lymphocytic leukaemia, are a severe hazard to public health globally. L-glutamine-degrading enzymes are required for the treatment of malignancies such as acute lymphocytic leukemia and breast cancer. L-glutaminase, an amidohydrolase, has been shown to be an effective chemotherapeutic tool for treating a variety of malignancies. The aim of the study: Molecular characterization is used in the study and production of bacterial L- glutaminase as an anticancer agent from a variety of Egyptian soil locales. The type of the study: Screening experimental study. Methodology: In the current study, many bacterial isolates were tested on mineral L-glutamine agar selective medium (MGA) to evaluate if they generated L-glutaminase. The most effective positive bacterial isolates that produce L-glutaminase, however, were discovered by morphological and biochemical analysis. The primary positive isolate producing L-glutaminase was also identified utilizing molecular detection by 16S rRNA sequencing homology technique. The properties of bacteria-produced L- glutaminase were investigated. The anticancer activity was assessed with an MTT assay. Results: Sole bacterial isolates that only needed L-glutamine for metabolic nitrogen grew well on MGA. The optimal conditions for producing positive bacterial isolates were pH 7.4 and 37 ̊C. The morphological and biochemical investigations of soil samples from diverse soil conditions in Egypt revealed that Bacillus subtilis subsp. niger (ATCC 9372) was the primary positive bacterial isolate producing L-glutaminase. At a pH of 7.4 and a temperature of 37 °C, the activators KCL, ZnSO4, FeSO4, K2HPO4, and MgSO4 offered ideal conditions for defining L-glutaminase production. L-glutaminase from Bacillus subtilis was detected to be a highly bioavailable and efficient anticancer treatment. The original yield [productivity] from MGA was 6.3 U/ml, but invitro coupled transcription and translation production raised it to 89± 1 U/ml. L-glutaminase had a molecular mass of approximately 36 kDa. The purification of L-glutaminase resulted total activity of 21,883 ± 15.67 (U), specific activity of 379.14 ± 7.35 (U/mg of protein), and purification fold of 1.82 ± 3.06. The enzymatic activators Ni2+ and Mg 2+ increased L-glutaminase activity by 20%, 27%, respectively. The compound showed significant anticancer activity (IC50 = 38.72, 8.6, 6.41, 19.02, 49.83, and 9.45 μg/ml) against cancer cell lines from the liver (HepG-2), colon (HCT- 116), breast (MCF-7), lung (A-549), lymphocytic (CCL-120), and cervical (Hela). The kinetic parameters Km and Vmax were 15.2^ 10 -3 M and 119.86 μmol/ml/min, indicating a higher affinity for the substrate. The enzyme demonstrated high efficacy at pH 6.5 and temperature 35. The enzyme was thermostable at 58 ̊C for 1 hour. Conclusion: Acute lymphocytic leukemia and breast cancer are two instances of auxotrophic malignancies for which L-glutamine is the sole metabolic source, and Bacillus subtilis- derived L-glutaminase was a suitable enzyme in their treatment.

Background: The World Health Organization identifies lung and prostatic cancers as solid tumors with significant global lethality, both being auxotrophic cancers for L-arginine aminoacid. The aim of the study: The study aims to detect L-arginase-expressing bacteria from various soil environments in Egypt using 16S rRNA and characterize its anticancer activity. Methodology: A hundred samples of Egyptian grassland soil were gathered at a depth of 11–20 cm, close to wheat mills. Using fast plate assay screening and spectrophotometric analysis, the presence of bacteria generating L-arginase was verified. The major soil bacterial isolates were identified by morphological characterization, biochemical responses, and 16SrRNA sequencing methods. The anticancer activity of the test enzyme was assessed using MTT assay. Results: On the MAA medium, only the bacterial isolates capable of using L-arginine as the only metabolic source for carbon and nitrogen were cultivated. Bacillus cereus DSM 360 was shown to be the prevailing bacterial isolate generating L-arginase using molecular detection and biochemical reactions. When Co+2, Ni+2, and Mn+2 metal ions were present as co-factors, bacterial L-arginase demonstrated remarkable anticancer action against auxotrophic tumors for L-arginine. The total protein content was 0.349 mg, while total enzyme activity was 8.174 U with 61% enzyme recovery. As well as the specific activity reached 23.4212 U/mg. Using the mass spectrometer, the molecular weight of the bacterial L-arginase was revealed to be 37 KDa. The bacterial L-arginase's IC50 values were 3.12 U/ml for the lung cancer cell line, 3.91 U/ml for prostatic cancer cell line, 0.91 U/ml for acute promyelocytic leukemia cancer cell line and 2.73 U/ml for kidney cancer cell line. The enzyme under test showed kinetic characteristics of 7.36 mmol/l and 6.14 μmol/min for Km and Vmax, respectively. The half-life time (T1/2) was 90.17 min at 50°С, while being 86.53 min at 60°С. The test enzyme was thermostable at 60°С for 1 hour. Conclusion: The study showed a potential strategy by identifying and determining a newly discovered bacterial L-arginase enzyme as an anticancer agent in Egypt's soil settings.

Performing optimisation and scale-up studies of crystallisation systems requires accurate and computationally efficient mathematical models. The assumption of the ideal mixing conditions in batch reactors typically produce inaccurate results while the computational expense of CFD models is still prohibitively high. Therefore, in this work, a new intermediary approach is proposed that takes into account the non-ideal mixing conditions in the reactor and requires less computational resources than full CFD simulations. Starting with the Danckwerts concept of the intensity of segregation, an analogy between its application to chemical reactions and the kinetics of the crystallisation phenomena (such as nucleation and growth) has been made. As a result, the modified kinetics expressions have been derived which incorporate the effect of non-idealities present in stirred reactors. This way, based on the experimental measurements of the mixing time using the Laser Induced Fluorescence (LIF) technique, computationally more efficient mathematical models can be developed in two ways: (1) the accurate semi-empirical correlations are available for standard mixing configurations with the most often used types of impellers, (2) CFD simulations can be utilised for estimation of the mixing time; in this case it is necessary to simulate only the mixing process. The benefits offered by the LIF experimental technique have been demonstrated and some frequent problems in its application analysed. The mixing time results for configurations with and without baffles for three types of impellers and four different rotational speeds have been presented. The false shorter mixing times in the non-baffled configurations have been observed and this phenomena explained by the existence of two segregated zones in the reactor and confirmed by additional experiments. The precise measurements in these cases have been shown as difficult using the LIF technique, particularly for higher rpms. The experimental data has been compared to the preliminary simulation results obtained from the Smoothed Particle Hydrodynamics method and the standard k-ε turbulence model with the modest success. The shortcomings of the SPH model have been recognized and the directions for the future work discussed.

The research aims to present an innovative methodology to execute the Heritage conservation processes in a collaborative and interdisciplinary BIM project, with an effective management of the deterioration suffered over time, emphasizing the structures and coatings. The research begins with the architectural survey using scanning techniques (TLS) and terrestrial photogrammetry (SfM) and taking as a study the Duomo of Molfetta (Italy), a unique Romanesque architecture of Puglia (Italy). The methodological process is mainly aided by the precise semantic segmentation of global point clouds, a semi-automatic process assisted by classification algorithms implemented in the post-processing software, and which has allowed the classification of the unstructured information provided by the remote sensing equipment when identifying the architectural-structural systems of a building with high historical values. Subsequently, it has been possible to develop an efficient Scan-to-HBIM workflow, where the Heritage-BIM (HBIM) project has fulfilled the function of a database by incorporating and organizing all the information (graphic and non-graphic) to optimize the tasks of auscultation, identification, classification, quantification and, in turn, facilitating the parametric modeling of unique structures and architectural elements. The results have shown great effectiveness in the processes of characterization of architectural and artistic heritage, focusing on the deformations and deterioration of the masonry in columns, and making multidisciplinary conservation work in an HBIM project more flexible. But there are still some difficulties for the automatic interpretation of 3D point cloud data, related to specific systems of the historical architecture. In conclusion, human action and interpretation continues to be a fundamental pillar to achieve precise results in a heritage environment.

This paper studies the maximum reliability of multi-hop relay UAV, in which UAV provides wireless services for remote users without direct communication link on the ground as a coded cooperative relay. In this paper, the analytical expressions of total power loss and total bit error rate are derived as reliability measures. Firstly, based on the environmental statistical parameters, a LOS probability model is proposed. Then the problem of minimizing the bit error rate of static and mobile UAVs is studied. The goal is to minimize the total bit error rate by jointly optimizing the height, elevation, power and path loss, and subject to the maximum allowable path loss con-straints, transmission power allocation constraints and UAV height and elevation constraints. At the same time the total path loss is minimized to achieve maximum ground communication cov-erage. However, the formulated joint optimization problem is non-convex and generally difficult to solve. Therefore, we decomposed the problem into two subproblems and proposed an effective joint optimization iteration algorithm. Finally, the simulation results are given, and the analysis shows that the optimal height of different reliability measures is slightly different, and using the mobility of UAVs can improve the reliability of communication performance.

Technological advancements and innovations have profoundly changed the lives of people giving rise to smart environments, cities, and societies. As homes are the building block of cities and societies, smart homes are critical to establishing smart living and are expected to play a key role in enabling smart cities and societies. The current academic literature and commercial advancements on smart homes have mainly focused on developing and providing smart functions for homes to provide security management and facilitate the residents in their various activities such as ambiance management. Homes are much more than physical structures, buildings, appliances, operational machines, and systems. Homes are composed of families and are inherently complex phenomena underlined by humans and their relationships with each other, subject to individual, intragroup, intergroup, and intercommunity goals. There is a clear need to understand, define, consolidate existing research, and actualize the overarching roles of smart homes, the roles of smart homes that would serve the needs of future smart cities and societies. This paper introduces our data-driven parameter discovery methodology and uses it to provide, for the first time, an extensive, rather fairly comprehensive, analysis of the families and homes landscape seen through the eyes of academics and the public using over a hundred thousand research papers and nearly a million tweets. We develop a methodology using deep learning, natural language processing (NLP), and big data analytics methods and apply it to automatically discover parameters that capture a comprehensive knowledge and design space of smart families and homes comprising social, political, economic, environmental, and other dimensions. The 66 discovered parameters and the knowledge space comprising 100s of dimensions are explained by reviewing and referencing over 300 articles from the academic literature and tweets. The knowledge and parameters discovered in this paper can be used to develop a holistic understanding of matters related to families and homes facilitating the development of better, community-specific, policies, technologies, solutions, and industries for families and homes, leading to strengthening families and homes, and in turn, empowering sustainable societies across the globe.

Schistosomiasis, acquired by skin-penetrating cercariae of dioecious digenean schistosomes during freshwater contact, afflicts nearly 260 and 440 million people with active infections and residual morbidity, respectively; about 10 million women at reproductive age contract schistosomiasis during gestation every year. Acute schistosomiasis is characterized by pre-patent pro-inflammatory CD4+ T-helper 1 or CD4+ Th1/T-helper 17 reactivity against immature schistosomulae. Chronic schistosomiasis is dominated by post-patent anti-inflammatory CD4+ T-helper 2 reactivity against ova epitopes; flukes co-exist in immunocompetent definitive hosts as they are capable of evading their defense mechanisms. Preventive measures should be complemented by vaccination, inducing long-term protection against transmission, infection, and disease recurrence, given the latest advancements in schistosomal vaccines. Transmission models incorporating vaccination available in PubMed, Embase and Web of Science up to December 31, 2023 are presented. Besides conceptual model differences, predictions meant to guide decision- and policymaking reveal continued worm harboring facilitating transmission besides residual infections, and increased susceptibility to re-infection and rebound morbidity, both shifted to later life stages following the intervention. Consequently, a vaccination schedule is pivotal considering the optimal age for initial immunization, i.e., pre-schoolchildren or schoolchildren, in a cohort-based or population-based manner while incorporating potential non-adherers promoting ongoing transmission; longevity over magnitude of vaccine protection to antigenic schistosomal moieties is crucial including accounting for existing pre-acquired immunity from natural exposure, in utero priming besides herd immunity, and induced by chemotherapy. Combining as one multi-component approach long-term effects of vaccination with short-term effects of chemotherapy as regular repeated vaccine-linked therapy in contrast to a single-component intervention seems most promising for achieving WHO’s endpoints of transmission elimination and morbidity control.

Biopolymer gels have gained tremendous potential for therapeutic applications due to their biocompatibility, biodegradability, and ability to adsorb and bind biological fluids, making them attractive for drug delivery and therapy. The versatility of biopolymer gels in theranostic backgrounds, with a focus on integrating imaging features and facilitating real-time monitoring of drug delivery. Different methods of delivery are explored imaging agents into biopolymer gels, including encapsulation, surface functionalization, nanoparticle encapsulation and layer-by-layer assembly techniques. Integration of Agents and Real-Time Monitoring Drug Delivery We summarize the synthesis methods, general properties, and mechanisms of biopolymer gels functionality, demonstrating their broad applications as multimodal systems for imaging-based therapeutics. These techniques not only enable multiple imaging but also provide signal enhancement and imaging a targeted facilitates, increasing the diagnostic accuracy and therapeutic efficacy. In addition, current techniques for incorporating imaging agents into biopolymer gels are discussed, and their role in precise drug delivery and monitoring.

This article introduces a new method for modelling and verifying the execution of timed security protocols (TSP) and their time-dependent security properties. The method, which is both novel and reliable, uses an extension of interpreted systems, accessible semantics in multi-agent systems, and timed interpreted systems (TIS) with dense time semantics to model TSP executions. We enhance the models of TSPs by incorporating delays and varying lifetimes to capture real-life aspects of protocol executions. To illustrate the method, we model a timed version of the Needham-Schroeder Public Key Authentication Protocol. We have also developed a new SMT-based bounded model checking reachability algorithm for the proposed structures and implemented it with the tool. The method comprises a new procedure for modelling TSP executions, a translation of TSP into TIS, and a translation of TIS's reachability problem into the SMT problem. The paper also includes thorough experimental results for nine protocols modelled by TIS and discusses the findings in detail.

The resilience of towns and cities refers to their ability to adapt and recover when confronted with pressures or challenges. This study employs ten variables as indicators to assess the resilience of urban areas by analyzing official data and constructing a multilevel mixed-effects structural equation model. The empirical findings demonstrate that enhancing resilience significantly influ-ences urban service functions, such as strengthening healthcare systems, stabilizing the real estate market, and addressing socio-economic challenges. Specifically, factors such as healthcare re-sources, housing demand, population structure, and social security exhibit varying levels of resil-ience, which profoundly impact the spatial distribution of these factors and socio-economic de-velopment. Disparities in healthcare resource allocation, demographic aging trends, and shifts in the housing market closely correlate with resilience levels in different regions. Additionally, the study emphasizes that improving resilience not only boosts the reliability and security of urban services but also ensures that communities receive necessary support and protection during times of adversity. Consequently, policymakers should recognize the pivotal role of urban resilience in resource allocation and social equity, devising corresponding strategies to enhance the resilience of these areas.

The controllability and consistency in the fabrication of micro-textures on large-scale remains a challenge for existing production processes. Mask electrolyte jet machining (MEJM) is an alternative to Jet-ECM for controllable and high-throughput surface microfabrication with more consistency of dimensional tolerances. This hybrid configuration combines the high-throughput of masked-ECM and the adjustable flow-field of jet-ECM. In this work, a duckbill jet nozzle was introduced to make MEJM more capable of batch micro-structuring. A multiphysics model was built to simulate the distribution of electrochemical reaction ions, the cur- rent density distribution and the evolution of the shape of the machined cavity. Experimental investigations are presented showing the influence of the machining voltage and nozzle moving speed on the micro cavity. Several 35 ×35 micro cavity arrays with a diameter of 24.92 − 11.73 µm and depth of 15.86 − 7.24 µm are generated on 304 stainless steel.

Background: Breast cancer and other neoplasms like acute lymphocytic leukemia pose a serious threat to public health worldwide. Treatment for malignancies including acute lymphocytic leukemia and breast cancer requires enzymes that break down L-glutamine. An amidohydrolase called L-glutaminase can be an effective chemotherapeutic tool for treating various cancers. Methods: On mineral L-glutamine agar selective medium (MGA), a few bacterial isolates were examined in the current investigation to see if they produced L-glutaminase. However, the most effective positive bacterial isolates generating L-glutaminase were identified using morphological and biochemical testing. Molecular detection using the direct Southern blotting approach was also used to determine the main positive isolate that produces L-glutaminase. L-glutaminase synthesis by bacteria was evaluated for its characteristics. Using an MTT test, the anticancer activity was evaluated. Results: exclusive bacterial isolates that used L-glutamine as their sole source of metabolic nitrogen exhibited favorable growth on MGA. PH 7.4 and a temperature of 37 0C were the ideal environmental and physiological conditions for developing positive bacterial isolates. From the soil samples taken from various soil conditions in Egypt, the morphological and biochemical analyses showed that Bacillus cereus 14579 was the main positive bacterial generating L-glutaminase isolate. At a pH of 7.4 and a temperature of 37 °C, the following activators—KCL, ZnSO4, FeSO4, K2HPO4, and MgSO4—provided the high-grade circumstances for characterizing L-glutaminase synthesis. Bacillus cereus-produced L-glutaminase has shown excellent bioavailability and effectiveness as an anticancer therapy. The yield [productivity] was 5.2 U/ml during the original manufacture from MGA, but it increased to 42.96 U/ ml by bacterial recombinant DNA manufacturing. The molecular mass of L-glutaminase was roughly 37 KDa. L-glutaminase was purified, yielding final enzyme recovery of 55 1.23%, total activity 12,990± 19.76 ( U), specific activity 384.66± 8.92( U/ mg of protein), and purification fold 2± 2.99. Furthermore, the L-glutaminase activity was raised by 19%, 23%, 15%, and 9%, respectively, by the enzymatic activators Mn2+, K+, Na+, and Fe3+. It demonstrated strong DPPH scavenging activity (IC50 = 61 μg/ mL) and anticancer activity( IC50 = 40.72, 9.7, 7.39, 20.61, 51.28, and 11.55 μg/ mL, respectively) against human liver (HepG-2), colon ( HCT-116), breast ( MCF-7), lung( A-549), lymphocytic( CCL-120), and cervical( Hela) cancer cell lines. A stronger affinity for its substrate was shown by the kinetic parameters of Km and Vmax, which were 13.2 10-5 M and 119.86 μmol/ ml/ min, respectively. Conclusion: Acute lymphocytic leukemia and breast cancer are examples of auxotrophic malignancies for which L-glutamine serves as the only metabolic source, and L-glutaminase generated by Bacillus cereus was an appropriate enzyme in the therapy of these diseases.

The electric vehicle (EV) industry challenges battery joining technologies by requiring higher energy density both by mass and volume. Improving the energy density via new battery chemistry would be the holy grail but is seriously hindered and progresses slowly. In the meantime, alternative ways, such as implementing more efficient cell packaging by minimizing the electrical resistance of joints are of primary focus. In this paper we discuss the challenges associated with the electrical characterisation of laser soldered joints in general, and the minimization of their resistive losses, in particular. In order to assess the impact of the joint resistance on the overall resistance of the sample, the alteration in resistance was monitored as a function of voltage probe distance and modelled by finite element simulation. The experimental measurements showed two different regimes: one far from of the joint area and another in its vicinity and within the joints cross section. The presented results confirm the importance of the thickness of the filler material, the effective and the total soldered area, and the area and the position of the voids within the total soldered area in determining the electrical resistance of joints.

The domain of construction engineering and management is evolving rapidly. Optimizing resource positioning is crucial for meeting the challenges of efficiency and productivity. This research presents a novel methodology that incorporates Agent-Based Modeling (ABM), Building Information Modeling (BIM), and Bluetooth Low Energy (BLE) technologies, augmented with a Client Early Warning System (CEWS) and a Decision Support System (DSS). What makes this study unique is that it provides a real-time methodology for resource allocation and project management, tailored to address the complexities of modern construction projects. The application of this integrated technological framework marks a significant leap in construction management, empowering data-driven decision-making and significantly improving project efficiency. Empirically validated through a case study at Helwan University's College of Engineering and substantiated by expert surveys, this research showcases a transformative model for resource management. The findings not only underscore the practical applicability of this approach but also open new horizons for its adoption in global construction practices, offering insights for future research endeavors focused on expanding these methodologies to a wider range of resources.

Daily vitamin D supplementation using higher than normal dosing (up to the upper limit, UL) and intermittent (once or twice per week) dosing were studied in patients with increased risk of vitamin D deficiency. Using a PubMed database an adequate search for published randomized control trials and other studies was done and results were analyzed. This review provides overview of use of 7000 IU daily, 30,000 IU per week or twice weekly and 50,000 IU weekly of vitamin D on rapid restore of 25(OH)D concentrations to at least 30 ng/mL in different groups of patients at high risk of vitamin D deficiency. The above mention dosing should be considered in adults with obesity or multi-diseased patients on requiring multi-treatment with the use of several drugs, including drugs affecting vitamin D metabolism. The simple schedule for 7000 IU/day, 30,000 IU/week or twice weekly or 50,000 IU/week, all for 6-8 weeks of use by patients representing the increased risk of vitamin D deficiency were provided for consideration. It appeared that higher daily doses or intermittent doses suggested above are effective, safe and responsive for patient’s preferences.

Water footprint has been widely used to illustrate the consumption of water in many situations; for instance, in products, processes or regions of interest. In this work, we analyzed – using a sensitivity analysis approach – the effect of some variables in the calculation of the water footprint in the viticulture in Brazilian Serra Gaúcha (the major producing region of Brazilian Wine).The classical Penman-Monteith model for evapotransporation was considered, with uncertainties in some parameters (dead mulch covering fraction in the vineyard, maximum temperatures for some months, altitudes and latitudes of the site). The sensitivity analysis was conducted using the SAFE toolbox under Octave framework. The results indicated that the the portion of the water footprint corresponding to the evapotranspiration is more sensitive to the values of mulch covering fraction and the altitude of the site in comparison with the latitude and the maximum temperatures.

Bovine respiratory disease (BRD) is the leading cause of morbidity and mortality in cattle raised in North America. At the feedlot, cattle are subject to metaphylactic treatment with macrolides to prevent BRD, a practice that may promote antimicrobial resistance and has resulted in an urgent need for novel strategies. Mannheimia haemolytica is one of the major bacterial agents of BRD. The inhibitory effects of two amphipathic, α-helical (PRW4, WRL3) and one β-sheet (WK2) antimicrobial peptides were evaluated against multidrug-resistant (MDR) M. haemolytica isolated from Alberta feedlots. WK2 was not cytotoxic against bovine turbinate (BT) cells by the MTT (3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyltetrazolium bromide) assay. All three peptides inhibited M. haemolytica, with WK2, being the most efficacious against multiple isolates. At 8-16 µg/ml, WK2 was bactericidal against Mh 330 in broth and at 32 µg/ml in the presence of BT cells, reduced the population by 3 logs CFU/ml without causing cytotoxic effects. The membrane integrity of Mh 330 was examined using NPN (1-N-phenylnaphthylamine), and ONPG (o-Nitrophenyl β-D-galactopyranoside) with both the inner and outer membranes being compromised. Thus, WK2 may be a viable alternative to the use of macrolides as part of BRD prevention and treatment strategies.

Session-based recommendations which aim to predict subsequent user-item interaction based on historical user behavior during anonymous sessions can be challenging tasks. Two main challenges need to be addressed and improved: (1) How to analyze these sessions to accurately and completely capture users’ preferences, and (2) how to identify and eliminate any interference caused by noisy behavior. Existing methods have not adequately addressed these issues since they either neglected the valuable insight that can be gained from analyzing consecutive groups of items or failed to take these noisy data in sessions seriously and handled them properly, which can jointly impede recommendation systems from capturing users’ real intentions. To address these two problems, we designed a multi-order semantic denoising (MSD) model for session-based recommendations. Specifically, we grouped items of different lengths as varying multi-order semantic units to mine the user’s primary intention from multiple dimensions. Meanwhile, a novel denoising network was designed to alleviate the interference of noisy behavior and provide a more precise session representation. The result of extensive experiments on three real-world datasets demonstrated that the proposed MSD model exhibited improved performance compared with existing state-of-the-art methods in session-based recommendation.

Public safety and intelligent surveillance systems critically depend on anomaly behavior detection for effective monitoring. In real-world pedestrian detection scenarios, prevalent challenges such as missed detections, complex background interference, and small target sizes hinder accurate anomaly identification. To address these issues, this study introduces YOLO-ABD, a lightweight method for anomaly behavior detection that integrates small target detection and channel shuffling. This method employs YOLOv8n as the baseline model, incorporating a small target detection mechanism in the Head part and utilizing GSConv convolution in the Backbone to enhance perceptual capability. Additionally, the SimAM attention mechanism is integrated to mitigate complex background interference, thereby improving target detection performance. Evaluation on the IITB-Corridor dataset demonstrated mAP50 and mAP50-95 scores of 89.3% and 60.6%, respectively. Generalization testing on the street-view-gdogo dataset further highlighted the superiority of YOLO-ABD over advanced detection algorithms, underscoring its effectiveness and generalizability. With a relatively small parameter count, YOLO-ABD presents an excellent lightweight solution for pedestrian anomaly behavior detection.

Earth observation satellites can capture images of specific areas in Earth's orbit based on user requirements. Despite the high demand for satellite imagery, satellites remain a scarce resource. When there are many observation tasks that are large and dense, they may interfere with each other due to satellite mobility. To address this issue, a multi-satellite scheduling algorithm based on a task merging mechanism has been proposed. This paper proposes a two-stage approach to the problem: task merging phase and merging task scheduling phase. The task merging phase introduces two methods based on Mean Shift and Complete Graph to generate the merging task set. In the merging task scheduling phase, a multi-satellite scheduling algorithm based on merging tasks is employed to solve the problem. Finally, certain measurement experiments suggest the effectiveness of the algorithm.

We recently demonstrated the effectiveness of long-term treatment with rifaximin and the probiotic VSL#3 at improving urogenital and gastrointestinal symptoms in patients with both chronic inflammatory prostatitis (IIIa prostatitis) and diarrhea-predominant irritable bowel syndrome (IBS-D), relative to patients with IBS-D alone. Because low-grade inflammation of the intestine and prostate may be one of the reasons for co-developing both IIIa prostatitis and IBS-D, we designed the present study to once again evaluate the efficacy of combined rifaximin and VSL#3 treatment in patients affected by IIIa prostatitis plus IBS-D, but we also measured seminal plasma pro-inflammatory (IL-6) and anti-inflammatory (IL-10) cytokines before and after treatment. We consecutively enrolled 124 patients with IIIa prostatitis and IBS-D (diagnosed using the Rome III criteria). Patients were randomized into two groups: group A (n=64) was treated with rifaximin (seven days per month for three months) followed by VSL#3, and group B (n=60) was treated with a placebo. At the beginning of the study and after three months of treatment, all patients completed NIH-CPSI and IBS-SSS questionnaires to score the severity of their urogenital and gastrointestinal symptoms, and we measured seminal plasma levels of IL-6 and IL-10 using ELISA. We defined patients who improved following the treatment as those with a ≥6-point reduction in their NIH-CPSI score or ≥50-point reduction in their IBS-SSS score. By the end of the intervention, 68.7% and 62.5% of patients from group A reported improved NIH-CPSI and IBS-SSS scores, respectively, compared to only 3.3% and 5% of the placebo group. Group A patients also had significantly lower mean seminal plasma levels of IL-6 (11.3 vs 32.4 pg/mL) and significantly higher mean levels of IL-10 (7.9 vs 4.4 pg/mL) relative to baseline, whereas levels of IL-6 and Il-10 did not change in the placebo group. The co-occurrence of two clinical phenotypes (IBS-D plus IIIa prostatitis) result in increased intestinal inflammation and altered immune activation, both of which can be balanced by treatment with rifaximin and VSL#3.

Railway has been used as one of the most crucial means of transportation in public mobility and economic development. For efficiently operating railways, the electrification system in railway infrastructure, which supplies electric power to trains, is essential facilities for stable train operation. Due to its important role, the electrification system needs to be rigorously and regularly inspected and managed. This paper presents a supervised learning method to classify Mobile Laser Scanning (MLS) data into ten target classes representing overhead wires, movable brackets and poles, which are recognized key objects in the electrification system. In general, the layout of railway electrification system shows a strong regularity of spatial relations among object classes. The proposed classifier is developed based on Conditional Random Field (CRF), which characterizes not only labeling homogeneity at short range, but also the layout compatibility between different object classes at long range in the probabilistic graphical model. This multi-range CRF model consists of a unary term and three pairwise contextual terms. In order to gain computational efficiency, MLS point clouds is converted into a set of line segments where the labeling process is applied. Support Vector Machine (SVM) is used as a local classifier considering only node features for producing the unary potentials of CRF model. As the short-range pairwise contextual term, Potts model is applied to enforce a local smoothness in short-range graph. While, long-range pairwise potentials are designed to enhance spatial regularities of both horizontal and vertical layouts among railway objects. We formulate two long-range pairwise potentials as the log posterior probability obtained by Naïve Bayes classifier. The directional layout compatibilities are characterized in probability look-up tables which represent co-occurrence rate of spatial relations in horizontal and vertical directions. The likelihood function is formulated by multivariate Gaussian distributions. In the proposed multi-range CRF model, the weight parameters to balance four sub-terms are estimated by applying the Stochastic Gradient Descent (SGD). The results show that the proposed multi-range CRF can effectively classify detailed railway elements, representing the average recall of 97.66% and the average precision of 97.07% for all classes.

This paper introduces a three-layer system, proposing a comprehensive model of granular mixture transport over a mobile sloped bed in a steady flow. This system, consisting of the bottom, contact and upper zones, provides complete, continuous sediment velocity and concentration vertical profiles. The model considers gravity’s effect on sediment transport in the bottom (dense) layer, a crucial factor often overlooked in previous studies. The induced movement in the mobile sublayer of the dense layer causes an increase in velocity at the upper boundary of this layer, significantly affecting the vertical distributions of velocity and concentration above this layer. We described the interactions between fractions and an intensive sediment mixing and sorting process in the contact layer. The proposed shear variation, with an increase in its maximum value at the bed, adds to the novelty of our approach. The data sets used for the model’s validation cover various conditions, including slopes, grain diameters, densities and grain mobility conditions, from incipient motion to a fully mobilised bed. This extensive validation process instils confidence in the theoretical description and its applicability to real-world scenarios.

Snow crab replaced groundfish fisheries as the primary focus of the Newfoundland and Labrador (NL) fishing industry in the mid-1990s. Over the past three decades, management philosophies in this male-only fishery have shifted from promoting industry expansion to promoting industry rationalization to implementing Precautionary Approach (PA) management. Until the mid-2010s, there were regionalized management strategies characterized by higher exploitation rates in northern than southern sub-stock units along the NL marine shelves. However, in the late 2010s, exploitation rates were permitted to elevate to high levels across the entire stock range in association with a large resource decline and evidence of biological harm through fishing emerged in chronically depleted areas. In 2019, when stock and fishery productivity were near historic lows, a multi-indicator PA system was informally introduced into management of the resource. This event coincided with anticipated improvements in stock and fishery performance. This paper examines the extent to which the multi-indicator PA management system, focused on promotion of both biological protection and maximization of fishing efficiency, may have contributed to recent improvements in stock and fishery status. A suite of indicators from areas implementing PA guidance into management in 2019 prior to formal adoption of the PA system in 2023 suggest the system has been highly beneficial in promoting rapid recovery, improving stock and fishery performance metrics to levels matching or exceeding historic levels under similar conditions. We discuss capacity of the system to better safeguard biological aspects of resource and fisheries productivity moving forward under a scenario of an expectant resource decline.

The extensive use of polypropylene (PP) in various industries has heightened interest in devel-oping efficient methods for recycling and optimising its mixtures. This study focuses on formu-lating predictive models for the Melt Flow Rate (MFR) and shear viscosity of PP blends. The in-vestigation involved characterising various grades, including virgin homopolymers, copolymers, and post-consumer recyclates, in accordance with ISO 1133 standards. The research examined both binary and ternary blends, utilising traditional mixing rules and symbolic regression to predict rheological properties. High accuracy was achieved with the Arrhenius and Cragoe models, at-taining R² values over 0.99. Symbolic regression further enhanced these models, offering signif-icant improvements. To mitigate overfitting, empirical noise and variable swapping were in-troduced, increasing the models' robustness and generalisability. The results demonstrated that the developed models could reliably predict MFR and shear viscosity, providing a valuable tool for improving the quality and consistency of PP mixtures. These advancements support the de-velopment of recycling technologies and sustainable practices in the polymer industry by opti-mising processing and enhancing the use of recycled materials.

The partial discharge (PD) event in high voltage insulation releases energy, exerts mechanical pressure, and generates elastic waves. Detecting and locating these PD events through short-duration acoustic pulses is well-established, particularly in gas-insulated systems and oil-insulated transformers. However, its full potential remains untapped in solid insulation systems, where the propagation capability of acoustic pulse and the acoustic reflections pose fundamental challenges to the Acoustic Emission (AE) detection technique. This study investigates the influence of reflections and multiple paths on the propagating acoustic pulse in polymeric insulating materials using a finite element method (FEM) in COMSOL. It was observed that the reflections from the boundary influence the propagating pulse's shape, peak magnitude, and arrival time. An analytical MATLAB model further quantifies the impact of multiple propagation paths on the shape, magnitude, and arrival time of the pulse travelling in a cylinder. Additionally, a Perfect Matched Layer (PML) was implemented in the COMSOL model to eliminate reflections from the boundary, and it revealed that the acoustic pulse magnitude decreases with distance following the inverse square law. In essence, the models aid in measuring how reflections contribute to the observed signals, facilitating the precise identification of the source of the PD event in the tested system.

Reservoirs created by damming rivers significantly modify the environment and problems may arise: the storage of nutrients and organic matter in reservoirs often leads to decreased water quality due to eutrophication. Reservoirs built on lowland rivers are exposed to significant nutrient loads, often leading to eutrophication. In this article, the Sulejów Reservoir, in Central Poland, was the subject of the research, which focused on the use of Sentinel-2 remote sensing data to detect phytoplankton blooms, and on understanding the pattern of wind-driven surface currents using the CCHE2D model (a depth-averaged hydrodynamic model). The calculation of the total phosphorus load has shown that the reservoir mainly acts as nutrient storage. Still, during the low flow and intensive phytoplankton bloom, it can be a source of nutrients. The distribution of phytoplankton bloom on the Sulejów Reservoir was documented using eight Sentinel-2 satellite images from the vegetation season of 2020 and the Normalized Difference Chlorophyll Index (NDCl). Coupling remote sensing data and numerical modelling helps to interpret the hydrodynamic model results and understand nutrients and sediment dynamics within the reservoir. Hydrodynamic modelling combined with remote sensing data can be a valuable tool for selecting appropriate locations for water quality measurements at monitoring stations.

Traditional 3D reconstruction models have consistently encountered a challenge: attaining high recall of object edges while preserving precision. In this paper, we introduce a post-processing method Multi-Head Attention Refiner (MA-R) aimed at tackling this challenge by integrating a multi-head attention mechanism within the U-Net style refiner module. The 3D reconstruction model applying this method demonstrates excellence in parsing intricate image details, resulting in significant enhancement of boundary predictions and increased recall rates. In our experiments, our method significantly enhances the reconstruction performance of Pix2Vox++ when multiple images are utilized as input. Specifically, it achieves an enhanced Intersection Over Union score of approximately 1.1% compared to the original Pix2Vox++ model when 16-view images are employed.

We propose an innovative approach called SMPTC3, designed specifically to enhance security and privacy in cross-chain transaction verification. This approach addresses multi-chain, multi-participant information exchange and large-scale cross-chain transfers, resisting various types of malicious attacks. We leverage the verifiability of cross-chain transactions based on smart contracts and innovatively transform transaction information into confidential sets, organizing them into quadratic secret polynomials. By utilizing secret sharing and random distribution techniques, we construct a secure multiparty computation method, tailored for cross-chain transactions. To enhance the efficiency of cross-chain transactions, we introduce cross-chain batch processing technology, grouping inter-chain transactions into cross-chain transaction sets. Unlike traditional distributed notary technologies, SMPTC3 designates honest participants as a cross-chain notary group, reducing the time required for redundant signature confirmations and significantly lowering the possibility of malicious notaries. Theoretical analysis and empirical experiments demonstrate that SMPTC3 is highly efficient in addressing cross-chain transaction security issues.

With the large-scale application of Internet of Things (IoT) in the medical field, eHealthcare has attracted wide attention. With the help of IoT devices, eHealthcare allows doctors to monitor patients’ health conditions and make recommendations accordingly. The addition of cloud computing greatly saves Healthcare Center’s (HC) computing resources. In order to provide privacy and fine-grained access control, Attribute-b ased encryption (ABE) is widely favored. HC usually operates multiple medical institutions in different regions, and each medical institution can be regarded as a attribute authority. Therefor, multi-authority (MA) ABE is usually concerned to encrypt the patient data. However for existing MA-ABE algorithms, the ciphertext is long and the efficiency of encryption and decryption is low. These problems will greatly increase the computing burden of patients and seriously affect the efficiency of data transmission. Hence we propose a decentralized key-policy MA-ABE in eHealthcare. The proposed algorithm can achieve decentralization, that is, it does not need central authority. Meanwhile, compared with existing MA-ABE algorithms, the length of ciphertext generated by our algorithm is shorter, and the efficiency of encryption and decryption is significantly improved. With the help of Java Pairing Based Cryptography, we carried out the experiments which show that our algorithm can effectively reduce the time required for encryption and decryption.

ABSTRACT Purpose: Tongue image analysis for disease diagnosis is an ancient traditional non-invasive diagnosis technique widely used by traditional medicine practitioners. Deep Learning based multi-label disease detection models offer tremendous potential to clinical decision support systems, by facilitating preliminary diagnosis. Methods: In this work, we propose a multi-label disease detection pipeline, where in observation and analysis of tongue images captured and received via smartphones assist in predicting the health status of an individual. All images are voluntarily given by subjects consulting collaborating physicians. Images thus acquired are first and foremost classified either into a diseased or a normal category by a 5-fold cross-validation algorithm using a convolution neural network (MobileNetV2) model for binary classification. Once the diseased label is predicted, the image is used to diagnose multiple diseases using the prediction algorithm based on DenseNet121. Results: Average accuracy of 93 % was achieved in classifying diseased from normal healthy tongue by detection model with MobileNetV2 architecture. Multilabel disease classification produced more than 90% accurate results for the seven class labels considered. Conclusion: AI based image analysis shows promising results and an extensive dataset could provide further improvements to this approach. Rather than employing high-cost sophisticated image capturing setup, experimenting with smartphone images opens opportunity to provide preliminary health status to individuals on smartphone prior to further line of treatment and diagnosis.

Assessing the quality of corn seeds necessitates evaluating their content of water, fat, protein, and starch. This study integrates hyperspectral imaging technology with chemometric analysis techniques to achieve non-invasive and rapid detection of multiple key components in corn seeds. Hyperspectral images of the embryo surface of maize seeds were collected within the wavelength range of 1100~2498nm. Subsequently, image segmentation techniques were applied to extract the germ structure of the corn seeds as the region of interest. Seven spectral data preprocessing algorithms were employed, and the Detrending Transformation (DT) algorithm was identified as the optimal preprocessing method through comparative analysis using the Partial Least Squares Regression (PLSR) model. To reduce spectral redundancy and streamline the prediction model, three algorithms were employed for characteristic wavelength extraction: Successive Projections Algorithm (SPA), Competitive Adaptive Reweighted Sampling (CARS), and Uninformative Variable Elimination (UVE). Using both the original spectra and the extracted characteristic wavelengths, four content detection models were constructed: PLSR, Back Propagation Neural Network (BPNN), Radial Basis Function Neural Network (RBFNN), and Least Squares Support Vector Machine (LSSVM). The experimental results demonstrate that the DT-CARS-LSSVM model exhibits exceptional accuracy and stability in predicting these four key components, with determination coefficients of 0.9877, 0.9344, 0.9827, and 0.9592, respectively. This study not only provides a scientific basis for evaluating the quality of corn seeds but also opens up new avenues for the development of non-invasive detection technology in related fields.

The state of the grinding wheel in the grinding process directly affects the surface quality of the workpiece. The monitoring of the wear state of the grinding wheel can effectively identify the wear information of the grinding wheel and timely and effectively repair the grinding wheel. In this paper, a multi-sensor fusion precision grinding wheel wear intelligent monitoring system is established for typical difficult-to-machine aerospace material titanium alloy, and a multi-eigenvalue fusion algorithm based on improved support vector machine (SVM) is proposed. The extracted sound emission signal wavelet packet decomposition coefficient mean square value, force signal grinding force ratio, and vibration signal effective value are used as the input of the improved support vector machine, and the identification strategy is adjusted by the entropy weight evaluation method. The results show that the monitoring system established in this paper can effectively identify the wear state of the grinding wheel, and the monitoring accuracy can reach more than 92%.

The objective of image super-resolution is to reconstruct a high-resolution (HR) image with the prior knowledge from one or several low-resolution (LR) images. However, in the real world, due to the limited complementary information, the performance of both single-frame and multi-frame super-resolution reconstruction degrades rapidly as the magnification increases. In this paper, we propose a novel two-step image super resolution method concatenating multi-frame super-resolution (MFSR) with single-frame super-resolution (SFSR), to progressively upsample images to the desired resolution. The proposed method consisting of an L0-norm constrained reconstruction scheme and an enhanced residual back-projection network, integrating the flexibility of the variational model-based method and the feature learning capacity of the deep learning-based method. To verify the effectiveness of the proposed algorithm, extensive experiments with both simulated and real world sequences were implemented. The experimental results show that the proposed method yields superior performance in both objective and perceptual quality measurements, compared to the baseline super-resolution algorithms in the cascade model. In addition, the experiment indicates that this cascade model can be robustly applied to different SFSR and MFSR methods.

Sustainable water resource management in Bangladesh's Gumti River Basin faces challenges from climate change, urbanization, and population growth. This study aimed to calibrate and validate the HEC-HMS model for the Gumti River to enhance flood prediction and water resource planning. The model was set up using precipitation, temperature, and discharge data from 2019-2021, with SRTM elevation data for catchment delineation. Manual calibration was performed for 2019-2020, followed by validation for 2021, using parameters such as Muskingum routing and SCS Curve Number. Model performance was evaluated using R², Nash-Sutcliffe efficiency (NSE), RSR, and PBIAS metrics. Results showed satisfactory to good performance, with R² values of 0.64 and 0.68 for calibration and validation, respectively. NSE values were within the satisfactory range, while PBIAS indicated very good performance with slight underestimation. The study concludes that the calibrated HEC-HMS model provides a reliable tool for simulating the Gumti River's hydrology, though there's room for improvement. Integration with flood frequency analysis, water quality monitoring, and climate change projections is recommended for comprehensive water resource management, alongside the implementation of Sustainable Water Resource Management principles and community engagement strategies.