The study sought to investigate the effect of Multi-choice Goal programming in project Portfolio Analysis, using Lagos State Project Portfolio from between 2017-2021 as a study case. Specifically, the objectives examined the effectiveness of multi-choice goal programming in analyzing the project Portfolio of Lagos State Government and investigated the possible lapses in the use of Multi-choice Goal programming in analyzing the project Portfolio of Lagos State Government. Data were gathered from the State financial Statements and analyzed using Lingo-17 Software. Based on the analysis, the study discovered that the goals formulated can be optimally and minimally attained as the positive deviational and negative deviational variables depict zero. This indicates that the cost incurred on the project portfolio was absolutely minimized during the period and at the same time; Lagos State Government derived the most preferred benefits from it. The study therefore concluded that the State minimized the project costs and at the same time maximized benefits while meeting its overall objectives.

Financial statements depict the condition of a company and need to be analyzed and evaluated to assess its performance. This research aims to analyze financial statements to describe the financial condition, measure business development over time, and evaluate the achievement of the com-pany's objectives. An optimization analysis of financial ratios is performed using the Weighted Goal Programming (WGP) model, which addresses multiple objectives by applying weights based on their priorities. The Analytical Hierarchy Process was used to determine the priority weights of deviation variables from each financial ratio target. Financial ratios were selected based on their impact on profit using factor analysis. The constructed WGP model aims to minimize deviations in Return on Assets, Operating Ratios, Operating Income Ratio, Total Assets Turnover, and Current Ratio. Computational calculations to solve the WGP model are per-formed using Python, with pseudocode provided. A case study on a company in the garment and textile sector was conducted and found that the Operating Ratio, Return on Assets, Operating Income Ratio, and Current Ratio still need improvement by developing strategies to achieve the targets. Sensitivity analysis was also employed to assess the resilience of the model in response to alterations in data.

The paper proposes TOPSIS method for solving multi-objective multi-level programming problem (MO-MLPP) with fuzzy parameters via fuzzy goal programming (FGP). At first, - cut method is used to transform the fuzzily described MO-MLPP into deterministic MO-MLPP. Then, for specific , we construct the membership functions of distance functions from positive ideal solution (PIS) and negative ideal solution (NIS) of all level decision makers (DMs). Thereafter, FGP based multi-objective decision model is established for each level DM for obtaining individual optimal solution. A possible relaxation on decisions for all DMs is taken into account for satisfactory solution. Subsequently, two FGP models are developed and compromise optimal solutions are found by minimizing the sum of negative deviational variables. To recognize the better compromise optimal solution, the concept of distance functions is utilized. Finally, a novel algorithm for MO-MLPP involving fuzzy parameters is provided and an illustrative example is solved to verify the proposed procedure.

The Vehicle Routing Problem (VRP) and its variants are found in many fields, especially logistics. In this study, we introduced an adaptive method to a complex VRP. It combines multi-objective optimization and several forms of VRPs with practical requirements for an urban shipment system. The optimizer needs to consider terrain and traffic conditions. The proposed model also considers customers' expectations, shipper considerations as goals, and the common goal like transportation cost. We offered compromise programming to approach the multi-objective problem by decomposing the original multi-objective problem into a minimized distance-based problem. We designed a hybrid version of the Genetic algorithm with the Local Search algorithm to solve the proposed problem. We evaluate the effectiveness of the proposed algorithm with the Tabu Search algorithm, the original Genetic algorithm on the tested dataset. The results show that our method is an effective decision-making tool for the multi-objective VRP and an effective solver for the new variation of VRP.

The advancement of autonomous capabilities in maritime navigation has gained significant attention, with a trajectory moving from decision support systems to full autonomy. This push towards autonomy has led to extensive research focusing on collision avoidance, a critical aspect of safe navigation. Among the various possible approaches, Dynamic Programming is a promising tool for optimizing collision avoidance maneuvers. This paper presents a DP formulation for collision avoidance of autonomous vessels. We set up the problem framework, formulate it as a multi-stage decision process, define cost functions and constraints focusing on the actual requirements a marine maneuver must comply with, and propose a solution algorithm leveraging parallel computing. Additionally, we present a greedy approximation to reduce algorithm complexity. Through case studies, we demonstrate the effectiveness of the proposed approach in navigating complex scenarios, contributing to the future of autonomous maritime navigation. Through case studies, we show the efficacy of our approach in navigating complex scenarios.

In real-life scenario, there are many mathematical tools to handle the incomplete and imprecise data. One of them is the fuzzy approach. This article aims to contribute to the literature of fuzzy multi-objective dynamic programming issues involving the fuzzy objective functions. The piecewise quadratic fuzzy numbers characterize these fuzzy parameters. Some basic notions in the problem under the α-pareto optimal solution concept is redefined and analyzed to study the stability of the problem. Furthermore, a technique, named as enhancing decomposition approach, is presented for achieving a subset for the parametric space that contains the sameα-pareto optimal solution. For a better understanding and comprehension of the suggested concept, a numerical example is provided.

In this paper, we consider a class of bilevel programming problems (abbreviated as, BLPP). Exploiting the generalized approximate convexity assumptions, we investigate the relations among the solutions of approximate Minty (respectively, Stampacchia) type variational inequalities (abbreviated as, AMTVI (respectively, ASTVI)), and the local ϵ-quasi solutions of the BLPP. Moreover, by employing the generalized Knaster–Kuratowski–Mazurkiewicz (abbreviated as, KKM)-Fan’s lemma, we derive some existence results for the solutions of approximate variational inequalities (abbreviated as, AVI), namely, AMTVI and ASTVI. A non-trivial example is given to highlight the importance of the established results. To the best of our knowledge, there is no research paper available in the literature that establishes relationships between the AVI and the BLPP under the assumptions of generalized approximate convexity in terms of limiting subdifferentials.

Traumatic pneumothorax (PTX) occurs in up to 50% of patients with severe polytrauma and chest injuries. Patients with traumatic PTX with clinical signs of tension physiology and hemodynamic instability are typically treated with an urgent decompressive thoracostomy, tube thoracostomy, or needle decompression. There is recent evidence that non-breathless patients with hemodynamically stable traumatic PTX can be managed conservatively through observation or a percutaneous pigtail catheter. We present here a 52-year-old woman who presented to the emergency department with 55 mm traumatic PTX. Following aspiration of 1500 ml of air, clinical improvement was immediately observed, allowing the patient to be discharged shortly thereafter. In hemodynamically stable patients with posttraumatic PTX, without specific risk factors or oxygen desaturation, observation or simple needle aspiration can be a reasonable approach. We aimed in this article to review the available literature on needle aspiration and conservative treatment of traumatic pneumothorax. A total of 12 studies were selected out of 190 articles on traumatic PTX, where conservative treatment versus chest tube decompression was compared. Our case report demonstrated that even a large PTX in a hemodynamically stable patient without other risk conditions, can be successfully treated conservatively with simple needle aspiration to avoid tube thoracostomy complications.

(1) Background: Cardiorespiratory fitness (CRF) is a prognostic factor regarding long time morbidity and mortality. To assess CRF the well-known gold standard is cardiopulmonary exercise testing (CPET), which is a time consuming and expensive test. Therefore, alternative methods for routine evaluation of CRF are needed for the general population as well as for specific patient groups such as children and young adults with congenital heart disease. The Stair Climbing Test (SCT) is a simple and resource saving test reported in the current literature. This test is used in various settings to assess different health associated risk factors including cardiorespiratory fitness, muscular resilience, therapy effectiveness or pre- and postoperative morbidity and mortality.

Advancements in computing technology have resulted in significant changes in education, healthcare, and manufacturing fields. Thus, personnel training in computer-related fields is directly related to national competitiveness. Therefore, the importance of programming education has been emphasized worldwide. Programming education has been conducted since the 1980s, however beginners often find programming tedious and difficult because of the cognitive burden of using text commands. Therefore, block-based programming environments, such as Scratch and Code.org, and beginner-oriented programming environments, such as Blockly and Pencil Code, have been de-veloped. However, they have limitations when transitioning from block to text-based programming. In this study, we conducted one semester of classes for 128 middle school, high school, and uni-versity students to determine whether an environment that allows using a text-based programming language in a block-based programming environment aids beginners’ understanding of program-ming instructions, command usage confidence, and programming usefulness. The results confirm that the usability of a block-based environment positively influences programming perception. This study is significant because it verifies the necessity and effectiveness of a block-based environment that employs a text-based programming language in programming education for beginners.

There is still a lack of a clinical test to reliably identify patients with Parkinson’s disease (PD) being at risk for aspiration. In this prospective, controlled, cross-sectional study we assessed if swallowing speed for water is a useful clinical test to predict aspiration proven by flexible endoscopic evaluation of swallowing (FEES). Due to this we measured the swallowing speed for 90 ml water in 115 consecutive and unselected PD outpatients of all clinical stages and 32 healthy controls. Average swallowing speed was lower in patients compared with controls (6.5 ± 3.9 ml/s vs. 8.5 ± 3.2 ml/s; p < 0.01). The disease-independent widely used threshold of < 10 ml/s showed insufficient sensitivity of 88% and specificity of 19% with unacceptable false-positive rates of 63% for patients and 69% for controls. Receiver operating characteristic (ROC) analysis was carried out to define a suitable cut-off value for detection of aspiration of water (area under the curve 0.72, p < 0.001) in PD patients. The optimized cut-off value was 5.5 ml/s with a sensitivity of 69% and a specificity of 64%. Overall, measuring swallowing speed is prone to methodological errors and not suitable as a screening instrument to predict aspiration in PD patients.

This paper presents a brief account and rationale for implementation of competency-based learning in any form of management and leadership development programmes in South Africa. The fact that competency-based learning (CBL), also known as outcomes-based learning has been scrapped from the schooling system in South Africa is unfortunate as this method enhances critical thinking skills and practical problem-solving skills. This paper presents CBL as a model of meta-cognitive approach to learning that integrates both theory and practice into experiential learning through six dimensions, namely, active learning, constructive learning, cumulative learning, goal-oriented learning, learner-centred and curriculum design strategies. In the advent of the fast-paced global economy, managers and leaders need to seek those business schools that value real-time practical approach to curriculum for relevance and to maximize shareholder value through human resource development. This brief presentation ends by recommending an approach through CBL that fosters three critical pillars of leadership development, namely: intellectual, behavioural and emotional agenda.

This paper studies the maximum reliability of multi-hop relay UAV, in which UAV provides wireless services for remote users without direct communication link on the ground as a coded cooperative relay. In this paper, the analytical expressions of total power loss and total bit error rate are derived as reliability measures. Firstly, based on the environmental statistical parameters, a LOS probability model is proposed. Then the problem of minimizing the bit error rate of static and mobile UAVs is studied. The goal is to minimize the total bit error rate by jointly optimizing the height, elevation, power and path loss, and subject to the maximum allowable path loss con-straints, transmission power allocation constraints and UAV height and elevation constraints. At the same time the total path loss is minimized to achieve maximum ground communication cov-erage. However, the formulated joint optimization problem is non-convex and generally difficult to solve. Therefore, we decomposed the problem into two subproblems and proposed an effective joint optimization iteration algorithm. Finally, the simulation results are given, and the analysis shows that the optimal height of different reliability measures is slightly different, and using the mobility of UAVs can improve the reliability of communication performance.

Visual Question Generation (VQG) from images is a rising research topic in both fields of natural language processing and computer vision. Although there are some recent efforts towards generating questions from images in the open domain, the VQG task in the medical domain has not been well-studied so far due to the lack of labeled data. In this paper, we introduce a goal-driven VQG approach for radiology images called VQGRaD that generates questions targeting specific image aspects such as modality and abnormality. In particular, we study generating natural language questions based on the visual content of the image and on additional information such as the image caption and the question category. VQGRaD encodes the dense vectors of different inputs into two latent spaces, which allows generating, for a specific question category, relevant questions about the images, with or without their captions. We also explore the impact of domain knowledge incorporation (e.g., medical entities and semantic types) and data augmentation techniques on visual question generation in the medical domain. Experiments performed on the VQA-RAD dataset of clinical visual questions showed that VQGRaD achieves 61.86% BLEU score and outperforms strong baselines. We also performed a blinded human evaluation of the grammaticality, fluency, and relevance of the generated questions. The human evaluation demonstrated the better quality of VQGRaD outputs and showed that incorporating medical entities improves the quality of the generated questions. Using the test data and evaluation process of the ImageCLEF 2020 VQA-Med challenge, we found that relying on the proposed data augmentation technique to generate new training samples by applying different kinds of transformations, can mitigate the lack of data, avoid overfitting, and bring a substantial improvement in medical VQG.

Global positioning systems (GPS) have recently been shown to reliably quantify the spatiotemporal characteristics of Polo, with the physiological demands of Polo play at low and high goal levels also investigated. This study aimed to describe the spatiotemporal demands of Polo across 0 – 24 goal levels. A player worn GPS unit was used to quantify distance, speed and high intensity activities performed. Data was divided into chukkas and five equine-based speed zones, grouped per cumulative player handicap and assessed using standardised mean differences. Average distance and speed per chukka increased in accordance with cumulative player handicap, with the magnitude of differences being Trivial – Large and Trivial – Very Large, respectively. Differences between time spent in speed zones 4 and 5 show a linear increase in magnitude, when comparing 0 goal Polo to all other levels of play (Small – Very Large; 6 – 24 goals, respectively). High intensity activities predominantly shared this trend, displaying Trivial – Large differences between levels. These findings highlight the increasingly demanding cardiovascular, anaerobic and speed-based needs of Polo ponies as playing level increases. Strategies such as high intensity interval training, maximal speed work and aerobic conditioning may be warranted to facilitate this development and improve pony welfare and performance.

Earth observation satellites can capture images of specific areas in Earth's orbit based on user requirements. Despite the high demand for satellite imagery, satellites remain a scarce resource. When there are many observation tasks that are large and dense, they may interfere with each other due to satellite mobility. To address this issue, a multi-satellite scheduling algorithm based on a task merging mechanism has been proposed. This paper proposes a two-stage approach to the problem: task merging phase and merging task scheduling phase. The task merging phase introduces two methods based on Mean Shift and Complete Graph to generate the merging task set. In the merging task scheduling phase, a multi-satellite scheduling algorithm based on merging tasks is employed to solve the problem. Finally, certain measurement experiments suggest the effectiveness of the algorithm.

Railway has been used as one of the most crucial means of transportation in public mobility and economic development. For efficiently operating railways, the electrification system in railway infrastructure, which supplies electric power to trains, is essential facilities for stable train operation. Due to its important role, the electrification system needs to be rigorously and regularly inspected and managed. This paper presents a supervised learning method to classify Mobile Laser Scanning (MLS) data into ten target classes representing overhead wires, movable brackets and poles, which are recognized key objects in the electrification system. In general, the layout of railway electrification system shows a strong regularity of spatial relations among object classes. The proposed classifier is developed based on Conditional Random Field (CRF), which characterizes not only labeling homogeneity at short range, but also the layout compatibility between different object classes at long range in the probabilistic graphical model. This multi-range CRF model consists of a unary term and three pairwise contextual terms. In order to gain computational efficiency, MLS point clouds is converted into a set of line segments where the labeling process is applied. Support Vector Machine (SVM) is used as a local classifier considering only node features for producing the unary potentials of CRF model. As the short-range pairwise contextual term, Potts model is applied to enforce a local smoothness in short-range graph. While, long-range pairwise potentials are designed to enhance spatial regularities of both horizontal and vertical layouts among railway objects. We formulate two long-range pairwise potentials as the log posterior probability obtained by Naïve Bayes classifier. The directional layout compatibilities are characterized in probability look-up tables which represent co-occurrence rate of spatial relations in horizontal and vertical directions. The likelihood function is formulated by multivariate Gaussian distributions. In the proposed multi-range CRF model, the weight parameters to balance four sub-terms are estimated by applying the Stochastic Gradient Descent (SGD). The results show that the proposed multi-range CRF can effectively classify detailed railway elements, representing the average recall of 97.66% and the average precision of 97.07% for all classes.

Early-life exposure to high-fat diet (HF) can program metabolic and cognitive alterations in adult offspring. Although the hippocampus plays a crucial role in memory and metabolic homeostasis, few studies reported the impact of maternal HF on this structure. We assessed the effects of maternal HF during lactation on physiological, metabolic and cognitive parameters in young adult offspring mice. To identify early-programming mechanisms in hippocampus, we developed a multi-omics strategy in male and female offspring. Maternal HF induced a transient increased body weight at weaning, a mild glucose intolerance only in 3-month-old male mice with no change in plasma metabolic parameters in adult male and female offspring. Behavioral alterations revealed by Barnes maze test were observed both in 6-month-old male and female mice. Multi-omics strategy unveiled sex-specific transcriptomic and proteomic modifications in the hippocampus of adult offspring. These studies that were confirmed by regulon analysis, showing that, although genes whose expression was modified by maternal HF were different between sexes, the main pathways affected were similar with mitochondria and synapses as main hippocampal targets of maternal HF. The effects of maternal HF reported here may help to better characterize sex-dependent molecular pathways involved in cognitive disorders and neurodegenerative diseases.

ABSTRACT Purpose: Tongue image analysis for disease diagnosis is an ancient traditional non-invasive diagnosis technique widely used by traditional medicine practitioners. Deep Learning based multi-label disease detection models offer tremendous potential to clinical decision support systems, by facilitating preliminary diagnosis. Methods: In this work, we propose a multi-label disease detection pipeline, where in observation and analysis of tongue images captured and received via smartphones assist in predicting the health status of an individual. All images are voluntarily given by subjects consulting collaborating physicians. Images thus acquired are first and foremost classified either into a diseased or a normal category by a 5-fold cross-validation algorithm using a convolution neural network (MobileNetV2) model for binary classification. Once the diseased label is predicted, the image is used to diagnose multiple diseases using the prediction algorithm based on DenseNet121. Results: Average accuracy of 93 % was achieved in classifying diseased from normal healthy tongue by detection model with MobileNetV2 architecture. Multilabel disease classification produced more than 90% accurate results for the seven class labels considered. Conclusion: AI based image analysis shows promising results and an extensive dataset could provide further improvements to this approach. Rather than employing high-cost sophisticated image capturing setup, experimenting with smartphone images opens opportunity to provide preliminary health status to individuals on smartphone prior to further line of treatment and diagnosis.

The article presents a model for optimizing biomass supply chains using the linear programming framework integrated with a Geographic Information System. Based on the distance from a given type of biomass resource, its calorific value, price, and transportation costs, the model identifies the optimal source of biomass, allowing it to cover the demand for the required total energy value with the lowest possible costs. The case study includes the Połaniec power plant in southeastern Poland and potential sources of forest biomass and agricultural straw within 100 km of the plant. Unit costs of biomass varied depending on biomass availability and energy demands. For energy demand on the level of 1 PJ yearly, the lowest unit costs of biomass (4.08 €/MJ) were when all kinds of biomass were available, and the highest (5.47 €/MJ) was when only stacked wood was available. As energy demand increased, unit costs increased, and the ability to meet this demand with just one type of biomass decreased. The energy biomass sector can utilize the model to benefit both biomass producers and their final buyers.

Keywords: olfactory rehabilitation; chronic pain; fMRI;

This paper proposes a new approach for multi-focus images fusion based on Region Mosaicing on Contrast Pyramids (REMCP). A density-based region growing method is developed to construct a focused region mask for multi-focus images. The segmented focused region mask is decomposed into a mask pyramid, which is then used for supervised region mosaicking on a contrast pyramid. In this way, the focus measurement and the continuity of focused regions are incorporated and the pixel level pyramid fusion is improved at the region level. Objective and subjective experiments show that the proposed REMCP is more robust to noise than compared algorithms and can fully preserves the focus information of the multi-focus images meanwhile reducing distortions of the fused images.

This report discusses the application of approximate dynamic programming (ADP) and Krylov subspace methods in solving sequential decision-making problems in machine learning. ADP is used when dealing with large state spaces or when the exact dynamics are unknown. The paper explores various ADP methods such as temporal difference learning and least-squares policy evaluation. The authors also focus on the use of Krylov subspace methods for solving the Bellman equation in ADP. The report provides insights into linear approximation, stochastic algorithms, and the Arnoldi algorithm for orthonormal basis. Overall, the paper highlights the theoretical foundation provided by ADP and its connection with Krylov subspace methods, shedding light on their application in computer science.

The meaning of a good social outcome in land use transport policy/planning has been relatively underdeveloped, compared to economic and environmental sustainability goals, but this is now changing. Cities are increasingly prioritizing reducing social exclusion, with the allied intent of providing all residents with equitable access to the benefits of their city. However, in jurisdictions that use cost-benefit analysis to guide government decision-making, this poses a challenge: monetization of the benefits of reducing social exclusion is poorly developed. An evaluation gap thus confronts benefit-cost based assessment of initiatives intended to reduce social exclusion, compared to initiatives directed towards societal economic and environmental goals. This is a particular problem for public transport services that primarily enable people at risk of mobility-related social exclusion to access more opportunities in their society (social transit). The benefits of reducing social exclusion associated with these services have not been monetized, so social transit initiatives are poorly placed to argue their merits against competing initiatives where benefit monetization is more advanced (e.g., mass public transport and roads). The paper summarizes Australian research that has developed monetized measures for the value of increased trip making, bridging/bonding social capital, sense of community and several conceptions of wellbeing, and of reducing neighbourhood disadvantage, as these contribute to reducing social exclusion. New Singaporean research on the value of trip making to support reduced exclusion is also presented, affirming the Australian trip values. Trip values are then used in case study examples to show they can make a material difference to the societal worth of initiatives intended to reduce exclusion. Using these trip values, and other pathway values linked to reducing social exclusion, closes or at least substantially reduces the evaluation gap confronting social goal achievement in land use transport policy and planning, strengthening the case for reducing exclusion. These values will assist jurisdictions that are seeking to provide their residents with more equitable access to the benefits of their city.

Since the end of 2019 and throughout 2020 the world has been devastated by the SARS COVID-19 pandemic. The sport world suddenly had to deal with a massive reorganization of events with important implications on the physical and psychological preparation of athletes and coaches. The purpose of this study was to explore how these changes impacted coaches’ and athletes’ goal setting strategies and their experience of goal adjustment. As part of a wider mixed-method project involving 2162 coaches and 1354 athletes, an online qualitative survey was used, and data collected were analyzed using reflexive thematic analysis. Findings highlighted three overarching themes, in response to goal adjustment: “Moving on toward new goals”, “Letting go of goals”, and “Trying to hold on”, with several themes and sub-themes identifying different nuances of athletes’ and coaches’ experience. The implications of such findings for the mental preparation of high-level athletes are discussed in two ways. Firstly, in light of existing literature on goal setting from an applied perspective; secondly, in the broader perspective of the sport culture and the application of our themes to other challenging moments that sport professionals might encounter.

Citizen science has the potential to support the delivery of the United Nations Sustainable Development Goals (SDGs) through its integration into national monitoring schemes. In this study, we explore the opportunities and biases of citizen science (CS) data when used either as a primary or secondary source for SDG 6.3.2 reporting. We use data from waterbodies that have both CS and regulatory monitoring in England and Zambia to explore their biases and complementarity. A comparative analysis of regulatory and CS data provided key information on appropriate sampling frequency, site selection and measurement parameters, necessary for more robust SDG reporting. The results show elevated agreement for pass/fail ratios and indicator scores for English waterbodies (80%) and demonstrate CS data can improve granularity and spatial coverage for SDG indicator scoring, even when extensive statutory monitoring programmes are present. In Zambia, management authorities are actively using citizen science projects to increase spatial and temporal coverage for SDG reporting. Our results indicate that design considerations for SDG focused citizen science can address local needs as well as provide a more representative indicator of the state of a nation’s freshwater ecosystems for international reporting requirements.

Polo is an equestrian team sport, consisting of Open and Women’s only handicapping systems. As cumulative player handicap increases in Open Polo, distance covered, average speeds and high intensity work performed per chukka also increase. These activities may differ in terms of distribution of, and their affect upon, match outcome in Women’s Polo, and thus have implications for equine preparation and management. This study aimed to quantify spatiotemporal differences between Open and Women’s Polo when matched for handicap and assess their affect upon chukka and match outcome using a prospective cohort design. Distance, speed and high intensity activity data were collected via player worn global positioning system (GPS) units during 16-goal Open and Women’s Polo tournaments. Notational analysis quantified chukka duration and chukka and game outcomes. Between group differences were assessed by independent samples t-tests, and two factor mixed effects ANOVA for within group analyses. Between group differences were analysed using an independent samples t-test with alpha defined a priori as p<0.05. Open and Women’s Polo differed by a small to large extent (ES: 0.54 – 1.81) for all spatiotemporal metrics. In Open Polo, players covered moderately more distance (429.0m; 238.9m to 619.0m), with small to large increases in high intensity activities performed in games won. Whereas in Women’s Polo, moderately higher maximum speeds were attained in games won (17.13 km/h; 11.86 km/h to 22.40 km/h) and a small increase in accelerations performed (5.1; 0.2 to 10.0). Open and Women’s Polo, when matched for handicap, present with small to large spatiotemporal differences that are likely of practical significance, and influence game outcome differently between codes. These differences do not necessarily mean that Polo ponies need to be trained differently for each code.

Attribute reduction is a core technique in the rough set domain and an important step in data preprocessing. Researchers have proposed numerous innovative methods to enhance the capability of attribute reduction, such as the emergence of multi-granularity rough set models, which can effectively process distributed and multi-granularity data. However, these innovative methods still have many shortcomings, such as how to deal with complex constraints and how to perform multi-angle effectiveness evaluations. Based on the multi-granularity model, this study proposes a new method of attribute reduction, namely using multi-granularity neighborhood information gain ratio as the measurement criterion. This method combines both supervised and unsupervised perspectives, and by integrating multi-granularity technology with neighborhood rough set theory, constructs a model that can adapt to multi-level data features. This model can select the optimal granularity level or attribute set according to the requirements. Finally, the proposed method is experimented with on 15 UCI datasets against six other attribute reduction algorithms. The experimental outcomes, upon analysis and comparative review, substantiate the reliability and consistency of the attribute reduction approach introduced in this study.

With the integrated development of the Internet, wireless sensor technology, cloud computing, and mobile Internet, there has been a lot of attention given to research about and applications of the Internet of Things. A Wireless Sensor Network (WSN) is one of the important information technologies in the Internet of Things; it integrates multi-technology to detect and gather information in a network environment by mutual cooperation, using a variety of methods to process and analyze data, implement awareness, and perform tests. This paper mainly researches the localization algorithm of sensor nodes in a wireless sensor network. Firstly, a multi-granularity region partition is proposed to divide the location region. In the range-based method, the RSSI (Received Signal Strength indicator, RSSI) is used to estimate distance. The optimal RSSI value is computed by the Gaussian fitting method. Furthermore, a Voronoi diagram is characterized by the use of dividing region. Rach anchor node is regarded as the center of each region; the whole position region is divided into several regions and the sub-region of neighboring nodes is combined into triangles while the unknown node is locked in the ultimate area. Secondly, the multi-granularity regional division and Lagrange multiplier method are used to calculate the final coordinates. Because nodes are influenced by many factors in the practical application, two kinds of positioning methods are designed: the unknown node is in the positioning unit or not. When the unknown node is on the side of the positioning unit, we use the method of vector similarity. Moreover, we use the centroid algorithm to calculate the ultimate coordinates of unknown node. When the unknown node is not on the side of the positioning unit, we establish a Lagrange equation containing the constraint condition to calculate the first coordinates. Furthermore, we use the Taylor expansion formula to correct the coordinates of the unknown node. In addition, this localization method has been validated by establishing the real environment.

As the adoption of renewable energy sources grows, ensuring a stable power balance across various time frames has become a central challenge for modern power systems. In line with the "dual carbon" objectives and the seamless integration of renewable energy sources, harnessing the advantages of various energy storage resources and coordinating the operation of long-term and short-term storage have become pivotal directions for future energy storage deployment. To address the complexities arising from the coupling of different time scales in optimizing energy storage capacity, this paper proposes a method for energy storage planning that accounts for power imbalance risks across multiple time scales. Initially, the Seasonal and Trend decomposition using the Loess (STL) decomposition method is utilized to temporally decouple actual operational data. Subsequently, power balance computations are performed based on the obtained data at various time scales to optimize the allocation of different types of energy storage capacities and assess the associated imbalance risks. Finally, the effectiveness of the proposed approach is validated through hourly applications using real-world data from a province in China over recent years.

Pneumatic nebulizers (as variations based on the Collison nebulizer) have been widely used for producing fine aerosol droplets from a liquid material. The basic working principle of those nebulizers has been qualitatively described as utilization of the negative pressure associated with an expanding gas jet to syphon liquid into the jet stream, then to blow and shear into liquid sheets, filaments, and eventually droplets. Detailed quantitative analysis based on fluid mechanics theory is desirable, to gain in-depth understanding of the liquid aspiration mechanism among other aspects of the Collison nebulizer behaviour. The purpose of present work is to investigate the nature of negative pressure distribution associated with compressible gas jet flow in the Collison nebulizer by a computational fluid dynamics (CFD) analysis, using an OpenFOAM® compressible flow solver. The value of the negative pressure associated with a gas jet flow is examined by varying geometric parameters of the jet expansion channel adjacent to the outlet of jet orifice. Such an analysis can provide valuable insights into fundamental mechanisms for liquid aspiration, helpful for designing improved pneumatic atomizer in the Aerosol Jet® direct-write system for micro-feature, high-aspect-ratio material deposition

Multi-rotor drones, a kind of unmanned equipment which is widely used in military, commercial consumption and other fields, has been developed very rapidly in recent years. However, their short flight time has hindered the expansion of their application range. This can be addressed by utilizing hydrogen fuel cells, which exhibit high energy density, strong adaptability to ambient temperature, and no pollution emissions, as the power source. Accordingly, the application of hydrogen fuel cells as the power source in multi-rotor drones is a promising technology that has attracted significant research attention. This paper summarizes the development process of hydrogen fuel cell mul-ti-rotor drones and analyzes the key obstacles that need to be addressed for the further development of hydrogen fuel cell multi-rotor drones, including structural lightweight, hydrogen storage methods, energy management strategies. Additionally, prospects for the future development of hydrogen fuel cell multi-rotor drones are presented.

Singapore, being a land-scarce country, is heavily dependent on imported food, which poses a challenge in ensuring food security. In addition, the substantial amount of food waste generated in Singapore further deepens food insecurity challenges, imposing enormous pressure on the country's food and land resources. In the recent years, valorising food waste streams into higher value products has been an increasing trend in tackling food wastage due to its economical and environmental benefits. This paper provides a thorough review on food waste valorisation in Singapore and summarizes critical information from the current food landscape to the food waste management strategies adopted. The review highlights the prototypes developed from food waste streams by the local research and development capabilities and the technological processing and techniques used for versatile applications ranging from food and nutraceuticals to urban agriculture. The challenges associated with the valorisation of food waste are also addressed. Two ambitious Initiatives by the Singapore government Zero Waste Plan and the 30-by-30 food security goal to encourage food waste valorisation are explored and presented. The review serves as a reference for other countries in ensuring food security and achieving sustainable development goals.

The Sustainable Development Goals (SDGs) represent a central framework to guide sustainable urban development (2030 Agenda). However, it is not clear how and where SDG 11 (Sustainable Cities and Communities) is being implemented, and how such implementation might be improved. We investigated this subject by analyzing United Nations (UN) SDG Good Practices data from 2018 to 2021. We applied five criteria to the 336 SDG 11 responses: (1) geography; (2) actors; (3) progress toward targets; (4) areas of implementation; and (5) scale of action. Overall, 86 of the 193 countries that adopted the 2030 Agenda submitted at least one SDG 11 good practice. 33 countries contributed 73.8% of the total, and most developing countries did not make submissions. A very small number of responses (between 2.6 and 9.1%) addressed equity-related targets. Good practices from developed countries were usually more technology-based and system-forming; developing countries typically focused on issues of day-to-day concern. Overall, this analysis points to the need for better and more systematic reporting on SDG 11 implementation, a more active public sector role in SDG implementation and reporting, more focus on dimensions related to social equity, and better formulation of urban sustainability targets and indicators in the future.

Memristor has attracted a lot of interest due to its high processing speed, low power consumption and high integration ability, which is critical for electronic systems and memory-centric computing. However, the memristor programming circuit and strategy are still inflexible and complex, since the signal generator/collector and stimulate pulse must be carefully matched and designed based on memristor intrinsic characteristics without reconfigurable. Here, a simple and effective circuit only consists a parallel reference-resistor-and-NMOS is designed to program memristor with a more than 99% memristance precision. And the amplitude and width of stimulate pulse are fixed to ±4V and 5ms, respectively. In order to cope with the device variation, such as ±10% tolerance of transition voltage, an optimized programming strategy was proposed and demonstrated great robustness. Additionally, a set of reference resistors and NMOSs have been added to facilitate multi-level memristance operation without requiring any changes to the circuit structure. This program circuit was also employed to program memristor crossbar remains 99% precision. In the end, a memristor-based convolutional neural network which controlled by our optimized programming circuit was used for image recognition, and 89.36% accuracy can be achieved even under 15.8% memristance tolerance. This novel circuit demonstrates a simple and flexible strategy in memristor programming, providing a new way to control memristor crossbar for practical application.

This paper introduces the implementation of a genetic programming (GP)-based procedure to the automatic design and tuning of process controllers. The proposed approach makes a significant contribution to the field of artificial intelligence (AI) in control engineering. Unlike other controller design methods, the GP-based program handles the entire design in the time domain, including differential operations like derivatives and integrals, without the need for intermediate inverse Laplace transformation. This approach not only simplifies the design process but also ensures that all generated controllers are implementable in physical systems. Furthermore, GP’s functions set includes various mathematical operations beyond basic arithmetic operators, such as trigonometric, exponential, and logarithmic operators. The performance and validity of the resulting controllers generated by the proposed GP-based approach are evaluated by verifying whether the generator can replicate the structure and performance of those produced by traditional controller design methods and, in some cases, achieve even better results. As a result, the GP-based approach presents a promising solution for automating the controller design process and addressing control problems in various engineering applications.

Different organisms, cell types, and even similar cell lines can dramatically differ in resistance to genotoxic stress. This testifies to the wide opportunities for genetic and epigenetic regulation of stress resistance. These opportunities could be used to increas the effectiveness of cancer therapy, develop new varieties of plants and animals, and search for new pharmacological targets to enhance human radioresistance, for example, for -manned deep space expeditions. Based on the comparison of transcriptomic studies in cancer cells, in this review we propose that there is a high diversity of genetic mechanisms of development of genotoxic stress resistance. This review focused onpossibilities and limitations of the proposed regulation of the resistance of normal cells whole organisms to genotoxic and oxidative stress by overexpressing of stress-response genes. Moreover, the existing experimental data on the effect of such overexpression on the resistance of cells and organisms to various genotoxic agents has been analyzed and systematized. We suggest that the recent advances in the development of multiplex and highly customizable gene overexpression technology that utilizes the mutant Cas9 protein and the wealth of available data on gene functions and their signal networks open new opportunities for research in this field.

The influence of short term water absorption on the mechanical properties of halloysite nanotubes-multi layer graphene reinforced polyester hybrid nanocomposites has been investigated. The addition of nano-fillers significantly increased the flexural strength; tensile strength and impact strength in dry and wet conditions. After short term water exposure; the maximum microhardness; tensile; flexural and impact toughness values were observed at 0.1 wt% MLG. The microhardness increased up to 50.3%; tensile strength increased up to 40% and flexural strength increased up to 44%. Compared to dry samples; the fracture toughness and surface roughness of all types of produced nanocomposites were increased that may be attributed to plasticization effect. Scanning electron microscopy revealed that the main failure mechanism is caused by the weakening of nano-filler-matrix interface induced by water absorption. It was further observed that synergistic effects were not effective at concentration of 0.1 wt% to produce considerable improvement in mechanical properties of produced hybrid nanocomposites.

With the rising cost of animal feed protein, finding affordable and effective substitutes is crucial. Walnut kernel cake, a polyphenols, fiber, protein and fat-rich byproduct of walnut oil extraction, has been underexplored as a potential protein replacement in pig feed. In this study, we found that feeding large Diqing Tibetan pigs walnut kernel cake promoted adipose deposition and improved pork quality during pig growth. Transcriptome analysis revealed the upregulation of genes ANGPTL8, CCNP, ETV4, and TRIB3, associated with adipose deposition. Pathway analysis highlighted enrichment in adipose-deposition-related pathways, including PPAR, Insulin, PI3K-Akt, Wnt, and MAPK signaling. Further analysis identified DEGs (differentially expressed genes) positively correlated with adipose-related traits, such as PER2 and PTGES. Single-cell transcriptome data pointed to the specific expression of CD248 and PTGES in adipocyte progenitor/stem cells (APSCs), pivotal for adipocyte differentiation and adipose deposition regulation. This study demonstrates walnut kernel cake's potential to substitute soybean cake in pig feed, providing high-quality protein and promoting adipose deposition. It offers insights into feed protein replacement, human functional food, fat metabolism, and related diseases, with marker genes and pathways supporting pig breeding and pork quality improvement.

An active power dispatch method for a microgrid (MG) with multi-type loads, renewable energy sources (RESs) and distributed energy storage devices (DESDs) is the focus of this paper. The MG operates in a grid-connected model, and distributed power sources contribute to the service for load demands. The outputs of multiple DESDs are controlled to optimize the active power dispatch. Our goal with optimization is to reduce the economic cost under time-of-use (TOU) price, and to adjust the excessively high or low load rate of distributed transformers (DTs) caused by the peak-valley demand and load uncertainties. To simulate a practical environment, the stochastic characteristics of multi-type loads are formulated. The transition matrix of system state is provided. Then, a finite-horizon Markov decision process (FHMDP) model is established to describe the dispatch optimization problem. A learning-based technique is adopted to search the optimal joint control policy of multiple DESDs. Finally, simulation experiments are performed to validate the effectiveness of the proposed method, and the fuzzification analysis of the method is presented.

Recent years have witnessed significant advances in reinforcement learning (RL), which has registered remarkable success in solving various sequential decision-making problems in machine learning. Most of the successful RL applications, e.g., the games of Go and Poker, robotics, and autonomous driving, involve the participation of more than one single agent, which naturally fall into the realm of multi-agent RL (MARL), a domain with a relatively long history, and has recently re-emerged due to advances in single-agent RL techniques. Although, typically, the communication protocol between agents is manually specified and not altered during training, recently, some papers have shown signs of trying to emerge a communication between agents on the one hand and, on the other hand, to understand what is exchanged between agents. So, there is a growing body of literature on this topic which includes qualitative and quantitative studies and the ones that apply mixed methods. This study presents the scoping review of the methodological strategies undertaken in a total of 16 research articles. The results present the critical appraisal of quantitative methods in terms of validity and reliability and for qualitative methods considering four trustworthiness factors. In the end, relevant insights are further explored with implications and reflections on how they can benefit one's research in the field.

This paper presents a case study on using Emacs and Org-mode for literate programming in undergraduate data science courses. Over three academic terms, the author mandated these tools across courses in R, Python, C++, SQL, and more. Onboarding relied on simplified Emacs tutorials and starter configurations. Students gained proficiency after initial practice. Live coding sessions demonstrated the flexible instruction enabled by literate notebooks. Assignments and projects required documentation alongside functional code. Student feedback showed enthusiasm for learning a versatile IDE, despite some frustration with the learning curve. Skilled students highlighted efficiency gains in a unified environment. However, uneven adoption of documentation practices pointed to a need for better incorporation into grading. Additionally, some students found Emacs unintuitive, desiring more accessible options. This highlights a need to match tools to skills levels, potentially starting novices with graphical IDEs before introducing Emacs. Key takeaways include literate programming aids comprehension but requires rigorous onboarding and reinforcement; Emacs excels for advanced workflows but has a steep initial curve. With proper support, these tools show promise for data science education.

Genetic Programming (GP) is a powerful Machine Learning (ML) algorithm that can produce readable white-box models. Although successfully used for solving an array of problems in different scientific areas, GP is still not well known in Remote Sensing. The M3GP algorithm, a variant of the standard GP algorithm, performs Feature Construction by evolving hyper-features from the original ones. In this work, we use the M3GP algorithm on several sets of satellite images over different countries to create hyper-feature from satellite bands to improve the classification of land cover types. We add the evolved hyper-features to the reference datasets and observe a significant improvement of the performance of three state-of-the-art ML algorithms (Decision Trees, Random Forests and XGBoost) on multiclass classifications and no significant effect on the binary classifications. We show that adding the M3GP hyper-features to the reference datasets brings better results than adding the well-known spectral indices NDVI, NDWI and NBR. We also compare the performance of the M3GP hyper-features in the binary classification problems with those created by other Feature Construction methods like FFX and EFS.

Quantum computers are machines that are designed to use quantum mechanics in order to improve upon classical computers by running quantum algorithms. One of the main applications of quantum computing is solving optimization problems. For addressing optimization problems we can use linear programming. Linear programming is a method to obtain the best possible outcome in a special case of mathematical programming. Application areas of this problem consist of resource allocation, production scheduling, parameter estimation, etc. In our study, we looked at the duality of resource allocation problems. First, we chose a real world optimization problem and looked at its solution with linear programming. Then, we restudied this problem with a quantum algorithm in order to understand whether if there is a speedup of the solution. The improvement in computation is analysed and some interesting results are reported.

Underwater visual detection technology plays a pivotal role in fields such as marine exploration. With the increasing demand for underwater monitoring, the quest for efficient and reliable methods for underwater target recognition has become particularly significant. To address this requirement, this study developed an innovative underwater object detection architecture based on YOLOv8, named YOLOv8-MU, aimed at significantly enhancing detection accuracy.By integrating the LarK module proposed in UniRepLKNet to optimize the backbone network, YOLOv8-MU aims to achieve a larger receptive field without increasing the model’s depth. Further, this research introduces C2fSTR, an innovative method that combines Swin Transformer with the C2f module. Additionally, we have incorporated the SPPFCSPC_EMA module, which combines Cross-Stage Partial Fast Spatial Pyramid Pooling (SPPFCSPC) with attention mechanisms, significantly improving the detection accuracy and robustness of various biological targets. Moreover, by introducing a fusion block based on DAMO-YOLO into the neck of the model, we further enhanced the model’s capability in multi-scale feature extraction. Finally, the adoption of the MPDIoU loss function, designed around vertex distance, effectively tackles the challenges of localization accuracy and boundary clarity in underwater organism detection. Experimental results on the URPC2019 dataset demonstrate that the YOLOv8-MU model achieved an [email protected] of 78.4%, marking improvements of 5.6%, 1.1%, and 4.0% over YOLOv5s, YOLOv7, and YOLOv8n respectively, indicating the leading performance (SOTA) of this method. On the other hand, further evaluation on the URPC2020 dataset confirmed the generalization capability of the YOLOv8-MU architecture, with its [email protected] reaching 80.4%, surpassing various models including YOLOv5x and YOLOv8n, showcasing the wide applicability of our proposed improved model architecture.

Assessment of extreme events and climate change on reservoir inflow is important for water and power stressed countries. Projected climate is subject to uncertainties related to climate change scenarios and Global Circulation Models (GCMs’). Extreme climatic events will increase with the rise in temperature as mentioned in the AR5 of the IPCC. This paper discusses the consequences of climate change that include extreme events on discharge. Historical climatic and gauging data were collected from different stations within a watershed. The observed flow data was used for calibration and validation of SWAT model. Downscaling was performed on future GCMs’ temperature and precipitation data, and plausible extreme events were generated. Corrected climatic data was applied to project the influence of climate change. Results showed a large uncertainty in discharge using different GCMs’ and different emissions scenarios. The annual tendency of the GCMs’ is bi-vocal: six GCMs’ projected a rise in annual flow, while one GCM projected a decrease in flow. The change in average seasonal flow is more as compared to annual variations. Changes in winter and spring discharge are mostly positive, even with the decrease in precipitation. The changes in flows are generally negative for summer and autumn due to early snowmelt from an increase in temperature. The change in average seasonal flows under RCPs’ 4.5 and 8.5 are projected to vary from -29.1 to 130.7% and -49.4 to 171%, respectively. In the medium range (RCP 4.5) impact scenario, the uncertainty range of average runoff is relatively low. While in the high range (RCP 8.5) impact scenario, this range is significantly larger. RCP 8.5 covered a wide range of uncertainties, while RCP 4.5 covered a short range of possibilities. These outcomes suggest that it is important to consider the influence of climate change on water resources to frame appropriate guidelines for planning and management.

Digital technology makes energy systems more dynamic, efficient, reliable and sustainable. Promoting the digital governance of renewable energy is not only a key part of energy transformation, but also an important initiative to cope with the global energy crisis, which provides a new impetus for realizing the goal of net-zero emissions. In order to achieve the "dual-carbon" goal, China has been actively promoting energy reform and enhancing the wide application of digital technologies in the development and utilization of renewable energy. The digital governance system and governance capacity of renewable energy is an important support for the modernization of the national governance system and governance capacity. Although the digital governance of renewable energy in China has better policy support and advantages, the dilemmas it faces are still relatively prominent, including unsound laws and policies, insufficient governance capacity, and security loopholes in digital technology, etc. Therefore, this paper proposes a problem-oriented approach to the digital governance of renewable energy. Therefore, this paper puts forward problem-oriented optimization suggestions to innovate the legal system of renewable energy digital governance, promote the digital transformation of China's renewable energy industry, provide development space for renewable energy digital governance in a diversified mode, and enhance the digital governance capacity by improving the renewable energy security system.

The speed-density or flow-density relationship is a fundamental aspect of traffic flow theory. Single-regime models often face challenges in consistently fitting empirical data under diverse traffic conditions. This paper addresses the inaccuracies of single-regime models, attributing them not only to their functional forms but also to data dispersion and sample selection bias. To mitigate these issues, the data is segmented into day and night periods, leading to the creation of separate models for each. Calibration results, conducted on data from two freeways, Tehran-Karaj and Tehran-Qom, reveal distinct challenges, with the former exhibiting high dispersion and the latter showing low dispersion. Surprisingly, single-regime models demonstrate notable effectiveness when applied to distinct day and night data. Further analysis, categorizing data into day and night, results in reduced errors (20-60% improvement in R-Square), emphasizing the potential for enhanced accuracy by considering distinct regimes. Overall, the study underscores the significance of regime-specific considerations for accurate traffic flow modeling. Upon thorough evaluation, the study highlights the superiority of the neural network Multi-layer Perceptron (MLP) over traditional models. The research discusses the implications of incorporating day and night parameters into the models, emphasizing their potential for accuracy enhancement.

Considering the unquestionable role of education in economic development, it has an impact at a macroeconomic level—contributing to enhancing productivity and innovation, reducing poverty and promoting social cohesion—and at a personal level—ensuring the improvement of knowledge, skills and individual capabilities and promoting social values like empowerment and equality. Notably, quality education is recognized as one of the Sustainable Development Goals (SDGs), which, jointly with other behaviors and attitudes, could impact the development of societies in other fields like health and well-being, cultural preservation, environmental sustainability and even peace and stability—all of them also listed as SDGs. However, the capacity, or not, to reach higher levels of compliance with quality in education (SDG 4) varies from country to country, according to the 2023 Sustainable Development Report results. Thus, the present study used a fuzzy set qualitative comparative analysis to assess the conditions for attaining higher levels of quality education based on the different indicators used to measure SDG 4. The analysis will allow comparisons of results among different countries and provide information about the initiatives that could be relevant to increasing quality education worldwide and for policymakers.

Deploying UAVs as aerial base stations is an exceptional approach to reinforce terrestrial infrastructure owing to their remarkable flexibility and superior agility. However, it is essential to design their flight trajectory effectively to make the most of UAV-assisted wireless communications. This paper presents a novel method for improving wireless connectivity between UAVs and terrestrial users through effective path planning. This is achieved by developing a goal-directed trajectory planning method using active inference. First, we create a global dictionary using TSPWP instances executed on various training examples. This dictionary contains letters representing available hotspots, tokens representing local paths, and words depicting complete trajectories and hotspot order. By using this world model, the UAV can understand the TSPWP’s decision-making grammar and how to use the available letters to form tokens and words at various levels of abstraction and time scales. With this knowledge, the UAV can assess encountered situations and deduce optimal routes based on the belief encoded in the world model. Our proposed method outperforms traditional Q-learning by providing fast, stable, and reliable solutions with good generalization ability.

This paper is devoted to the study of multi-dimensional integral transform with Fox H-function in the kernel in weighted spaces integrable functions in the domain R+n with positive coordinates. Mapping properties such as the boundedness, the range, the representations of the considered transformation are established.

This paper presents an innovative multi-agent, data-driven reinforcement learning (RL) approach to develop and utilize the thermal equivalent network model that represents the motor's thermal dynamics. A multi-agent reinforcement learning is designed and trained to adjust the model parameters using data from several motor driving cycles. To ensure the incoming driving cycle matches the historical data before employing the pre-trained RL agents, offline statistical analysis and clustering techniques are developed and used. Numerical simulations highlighted the RL agent's ability to develop strategies that effectively address the variability of driving cycles. The proposed RL framework showed its capability to accurately reflect the motor's thermal behavior under various driving conditions.

This paper is regarding design and program an Micro-controller Arduino Uno board by using Arduino software to work as a photo-sensor(Active) single axial solar tracker system(SASTS). A solar panel, two photo-resistors (LDR) in two sides (north/south) of the photo-voltaic(PV) and a servo motor are connected to the Uno board, which is running a code that prepared by Arduino software IDE in advanced then it works as a tracking system. Here, the LDRs send the signal of presence or absence of the light to the board and based on that sent signal the Uno reflects a new signal to the servo motor to rotate and finds the light source. Lastly, the photo-sensor single axis tracker is made while Continuously, the system tries to face the panel to the sun and whilst changing the irradiance intensity it starts searching to find the angle of highest irradiance. Based on results that are extracted from the data, the tracker system significantly boosts the output efficiency of the solar panel. By using the Micro-controller Uno board, LDRs, servo motor and special designed mechanical base, the tracking system is constructed, based on acquired data the influence of the STS on the increasing the solar panel efficiency is more obvious. Significantly, the tracker system rises the efficiency of the PV .

Vulnerability is the big issue of the small inland urban centers exposed to the risk of depopulation. In the climate and in the context of an increasing seismic risk in the center-northern part of Italy, seismic vulnerability can become the determinant cause of the final abandonment of a small town. In some Italian regions, as well as Emilia Romagna, municipalities are implementing seismic vulnerability reduction policies based on the Emergency Limit Condition that has become a basic reference for ordinary land planning. This study proposes a valuation planning approach to the seismic vulnerability reduction carried out within the general planning framework concerning the Faentina Union, a group of five small towns located in the south-western part of the Province of Ravenna, Italy. The approach consists of three main stages: knowledge – the typological, constructive and technological description of the buildings specifically concerning their vulnerability degree; interpretation – the analyses aimed to outline a range of hypotheses about the damages in case of seism; planning – identifying the works intended to definitely reduce the vulnerability of the buildings. This stage includes a cost modelling tools aimed at outlining the trade-off between the extension and the intensity of the vulnerability reduction works, given the budget.

Keywords: pelvic ultrasound, follicle number per ovary, FNPO, ovarian volume, PCOM, upper normal limits, referral population

Students in their first year of computer science (CS1) at universities typically struggle to grasp programming concepts. This paper covers research using a Java programming language-guided visual execution environment (VEE) to teach CS1 students about programming concepts. The topics covered include input and output, conditionals, loops, functions, arrays, recursion, and files, all of which are covered in an introductory programming course. The VEE walks beginner programmers through the fundamentals of programming, utilizing visual metaphors to explain and direct interactive Java tasks. The primary goal of this study is to determine whether a cohort of 105 CS1 students from four different groups who are enrolled in two universities—one in Madrid, Spain, and the other in Galway, Ireland—can advance their programming abilities under the guidance of the VEE. Second, does the improvement vary depending on the programming concept? The findings demonstrate that students' programming knowledge has greatly increased. This improvement is significant for all programming concepts, while it is more pronounced for some topics than others, such as operators, conditionals, and loops. Additionally, it demonstrates that students had little prior understanding of files and recursion. The most well-known concept to them was the sequence concept.

The focus of this paper is on analyzing the role and the choice of parameters in sociophysics diffusion models, by leveraging the potentialities of sociophysics from a mathematical programming perspective. We first present a generalised version of Galam’s opinion diffusion model (see, e.g. , ). For a given selection of the coefficients in our model, this proposal yields the original Galam’s model. The generalised model suggests guidelines for possible alternative selection of its parameters that allow to foster diffusion. Examples of the parameters selection process as steered by numerical optimisation, taking into account various objectives, are provided.

In this paper, a new approach to retrieve semantic images based on shape and geometric features of image in conjunction with multi-class support vector machine is proposed. Zernike moment as shape feature is to verify the invariance of objects for silhouette image. In addition, a set of geometrical features is to explore the objects shape using two features of rectangularity and circularity. Then the extracted features are normalized and employed for multi-class support vector machine either for learning or retrieving processes. The retrieving process relies on three main tasks which namely Query Engine, Matching Module and Ontology Manger, respectively. Query Engine is to build the input text or image query using SPARQL language. The matching module extracts the shape and geometric features of image’s objects and employ them to Ontology Manger which in turn inserts them in ontology knowledge base. Benchmark mammals have been conducted to empirically conclude the outcome of proposed approach. Our experiment on text and image retrieval yields efficient results to problematic phenomena than previously reported.

Probiotic feed additives have attracted considerable research interest in recent years because the effectiveness of probiotics can differ across microbial strains and the supplemented macroorganisms. The present study was conducted on 16 lambs divided into two groups (C - control and E - experimental). The examined lambs were aged 11 days at the beginning of the experiment and 40 days at the end of the experiment. The diet of group E lambs was supplemented with a multi-strain probiotic formulation (Lactobacillus plantarum AMT14, Lactobacillus plantarum AMT4, Lactobacillus rhamnosus AMT15, and Bifidobacterium animalis AMT30), whereas group C lambs did not receive the probiotic additive. At the beginning of the experiment (day 0) and on experimental days 15 and 30, blood was sampled from the jugular vein to determine and compare: phagocytic activity (PHAGOTEST) and oxidative metabolism (PHAGOBURST) of peripheral blood granulocytes and monocytes by flow cytometry. An analysis of the phagocytic activity of granulocytes and monocytes revealed significantly higher levels of phagocytic activity (expressed as the percentage of phagocytic cells and mean fluorescence intensity) in lambs administered the multi-strain probiotic formulation than in the control group. The probiotic feed additive also exerted a positive effect on the oxidative metabolism of both granulocytes and monocytes (expressed as the percentage of oxidative metabolism and mean fluorescence intensity) after stimulation with Escherichia coli bacteria and with PMA (4-phorbol-12-β-myristate-13-acetate).

Systemic sclerosis (also known as scleroderma) is a chronic fibrosing autoimmune disease with both skin and multisystem organ involvement. Scleroderma has the highest mortality among all rheumatic diseases. The pathophysiology mechanism of systemic sclerosis is a progressive self-amplifying process, which implicates the widespread microvascular damage, followed by a dysregulation of innate and adaptive immunity and inflammation, and diffuse fibrosis of the skin and visceral organs. Fibrosis of internal organs is a hint for systemic sclerosis, moreover associated with interstitial lung disease (SSc-ILD) is a complex process. We report a case of a 56 years old female, diagnosed with Systemic Sclerosis 16 years ago. The systemic and clinical manifestations, respiratory functional tests, radiological aspects and specific therapy were discussed.

In 2010, Parties to the Convention on Biological Diversity (CBD) adopted the Strategic Plan for Biodiversity 2011–2020 to address the loss and degradation of nature. Subsequently, most biodiversity indicators continued to decline. Nevertheless, conservation actions can make a positive difference for biodiversity. The emerging Post-2020 Global Biodiversity Framework has potential to catalyze efforts to ‘bend the curve’ of biodiversity loss. Thus, the inclusion of a goal on species, articulated as Goal B in the Zero Draft of the Post-2020 Framework, is essential. However, as currently formulated, this goal is inadequate for preventing extinctions, and reversing population declines; both of which are required to achieve the CBD’s 2030 mission. We contend it is unacceptable that Goal B could be met while most threatened species deteriorated in status and many avoidable species extinctions occurred. We examine the limitations of the current wording and propose an articulation with robust scientific basis. A goal for species that strives to end extinctions and recover populations of all species that have experienced population declines, and especially those at risk of extinction, would help to align actors towards the transformative actions and interventions needed for humans to live in harmony with nature.

The essence of cross-modal generation and retrieval modeling for image-text interactions lies in semantic consistency. Among these, cross-modal representation alignment serves as the foundational requirement for achieving cross-modal semantic consistency. The crux of our proposed method entails the collaborative training of an image captioning model(referred to as the ’captioner’) and a pair of contrastive encoders for image-text matching(referred to as the ’concoder’). This synergistic approach yields concurrent enhancements in concoder’s performance, captioner’s proficiency, and cross-modal semantic coherence. We coin the proposed method as ‘ReCap’. To begin, we initialize the concoder through knowledge distillation from a pre-trained model. During the training process, we use the output of the initialized concoder as input to a residual attention network, jointly training it with the captioner to achieve semantic consistency. Subsequently, we iteratively update the concoder during the image-text momentum encoding phase using the residual attention network, creating a closed-loop for semantic consistency resolution. Upon completion of training, the concoder and captioner modules can be used independently to perform tasks related to cross-modal retrieval and cross-modal generation of text and images. In order to substantiate the efficacy of our proposed method, we initially conducted empirical experiments encompassing image-text retrieval and image captioning tasks, employing a widely recognized benchmark dataset, MSCOCO. Subsequently, we assessed the fine-grained cross-modal alignment performance of the concoder through an image classification task on the iNaturalist 2018 dataset. The achieved performance metrics notably surpassed those achieved by several incumbent state-of-the-art models, thus validating the proficiency of our method. Finally, motivated by the practical requirements of handling the nature conservation image data, we performed caption annotation for the iNaturalist 2018 dataset. Subsequently, we trained the ReCap on this annotated data. Experimental results demonstrate that our proposed method can maintain semantic consistency between cross-modal retrieval and image caption generation for species with similar visual features but distinct semantics. This achievement signifies a meaningful exploration in the field of cross-modal semantic consistency representation, holding significant practical value in the domain of biological research.

Biochar is a carbonaceous material derived from the thermochemical conversion of biomass under oxygen-lean conditions. Its properties render it many applications in agriculture, environmental remediation, and catalysis. Commonly produced by pyrolysis under a nitrogen atmosphere, the biochar composition is influenced mainly by residence time, heating rate, and process temperature. The existing literature primarily assesses biochar properties, such as ultimate, proximate, calorific, porosity, and combustibility, generated under various thermo-conversion conditions. However, there is a notable lack of sufficient investigation and attention given to the practical application of biochar. This article seeks to bridge that gap by enhancing the comprehension of the necessary experimental assessment for specific biochar applications and proposing process optimization methods using Multi-Criteria Decision Analysis (MCDA). By delving into these aspects, the study offers a concise overview of biochar production and presents a comprehensive panorama based on articles and patents. Additionally, the research explores the physicochemical characterization techniques associated with biochar and its various applications in conjunction with MCDA. This comprehensive approach aims to uncover valuable insights that could further advance the practical and sustainable utilization of biochar in a wide range of fields.

Introduction: maxillary hypoplasia and mandibular asymmetry may be corrected with orthognathic surgery at the completion of growth. Many patients require segmental Le Fort I osteotomies to obtain the most stable results. Unfortunately, if Invisalign is chosen for pre-surgical preparation, ClinCheck © software does not allow for prediction when these complex surgeries are planned. The objective of this paper was to show the potential of aligners beyond its software in most complex cases like multiple-piece maxillary osteotomies in cleft and non-cleft patients. Method: Thirteen patients who underwent pre-surgical treatment with clear aligners-Invisalign (study group) were matched in terms of diagnosis, surgical procedure, and orthodontic complexity with thirteen patients treated using fixed appliances (control group). A technique based on simple superimposition was devised to enhance the software for creating a suitable occlusion for segmental pre-surgical treatments. Virtual curves following the lower arch were employed to guide the correct pre-surgical positions of the upper teeth. The amount of impressions required in both groups to achieve satisfactory pre-surgical alignment of the segmented arches was compared. Results: one or no refinement phase were needed in the Invisalign group to reach an acceptable pre-surgical occlusion while the amount of pre-surgical impressions taken in order to reach adequate coordination with fixed appliance treatment was slightly higher. The average overall treatment duration did not show a statistically significant variation between the groups. Conclusions: it appears that clear aligner could serve as an effective treatment for individuals with skeletal discrepancies, including cleft and craniofacial anomalies, necessitating segmental Le Fort I osteotomies when aided by the suggested superimposition approach during digital pre-surgical movement simulations. More sophisticated softwares will certainly be implemented in the future.

Harnessing Quantum Energy States for Unprecedented Computing Capabilities In this proposal, we advocate for the use of energy states as fundamental units of quantum computer programming. Each unit of programming is conceptualized as an energy state, manifested as an essence-unit. An essence-unit, defined as the minimal form encapsulating complete uniqueness or specificity, serves as the cornerstone of this paradigm. This approach enables the recording of various forms of matter on quantum computers in essence-units, portraying their energy states. The recording of energy states is achieved through the creation of four distinct coherent potentials, facilitated by quantum dots or crystals. Crucially, these energy states embodied in essence-units resist subdivision. The study explores the intricate relationship among similarity, fractals, and uniqueness in quantum dot operations, revealing their profound implications for information transfer efficiency. Normalized entropy characterizes charge localized in quantum dot impurities in systems that have distortions. Through the utilization of N-level recording and entropy-fractal dimension equivalence, the paper elucidates the potential of quantum dots in reducing transmission time and modeling complex systems. The proposed methodology signifies a paradigm shift in quantum computing, presenting unparalleled possibilities for tackling hitherto insurmountable challenges.

This research work focused on the risks we are faced with on our day to day activities, either directly or indirectly, which can gradually accumulates and results to communal crisis, religious crisis, socio-economic agitations and tribal crises. Nasarawa Eggon Local Government Area of Nasarawa State was used as case study and a well structure close–ended questionnaire was used for data collection as it relates to Controlled Self Risk Assessment (CSRA) and linear programming technique was used to analyze. The results proved that many of this processes were neglected in these communities, making them to be prone to incessant communal crisis. The study recommend that Government should strongly, as a matter of urgency address the unemployment rate, distribution of political position, schools, primary health care and equip security personnel with the modern technology facilities, which happen to record the highest risk level.

Disorders of swallowing often lead to pneumonia when material enters the airways (aspiration). Flexible Endoscopic Evaluation of Swallowing (FEES) plays a key role in the diagnostics of aspiration but is prone to human errors. An AI-based tool could facilitate this process. Recent non-endoscopic/non-radiologic attempts to detect aspiration using machine-learning approaches have led to unsatisfying accuracy and show black box characteristics. Hence, for clinical users it is hard to trust in these model decisions. Our aim is to introduce an explainable artificial intelligence (XAI) approach to detect aspiration in FEES. Our approach is to teach the AI about the relevant anatomical structures like the vocal cords and the glottis based on 92 annotated FEES videos. Simultaneously, it is trained to detect bolus that passes the glottis and becomes aspirated. During testing, the AI successfully recognized glottis and vocal cords, but could not yet achieve satisfying aspiration detection quality. Albeit detection performance has to be optimized, our architecture results in a final model that explains its assessment by locating meaningful frames with relevant aspiration events and by highlighting the suspected bolus. In contrast to comparable AI tools, our framework is verifiable, interpretable and therefor accountable for clinical users.

The Circular Bioeconomy (CBE) combines the concepts of bioeconomy and circular economy. As an alternative concept to the current fossil-based, linear economy, it de-scribes an economy based on the efficient valorization of biomass. It is regional in nature and aims to improve sustainability. An analysis of the transition process, by identifying its success criteria and assessing its impacts through the modelling of technology-specific scenarios is necessary to ensure that CBE concepts are sustainable. However, a compre-hensive consideration of regional influences on both is lacking. Based on extensive literature research and an expert survey, we (i) present a compre-hensive catalog of CBE success criteria and discuss their region-specific character and (ii) develop a methodology based on evaluation matrices that enable to match CBE technolo-gies with regions. The matrices support the evaluation of technological and regional characteristics influencing the successful CBE implementation. The results show that the success criteria "biomass resources", "technological", and "social" are perceived as highly important, and that most of the success criteria are both region- and technology-specific, highlighting the relevance of developing matrices to match them. We describe such matrices indicatively for the two broadest and most im-portant success criteria clusters “social acceptance” and “biomass supply chain”. With this, we substantiate the regional nature of CBE and raise the awareness on the importance of considering regional conditions in CBE transition processes. Furthermore, we provide practical guidance on how regional conditions can be reflected in the selection of technologies, e.g. in regional CBE technology scenarios.

Recycling waste products is an environmental-friendly activity that can bring benefits to accompany, saving manufacturing costs and improving economic efficiency. For the beer industry, recycling bottles can reduce manufacturing costs and reduce the industry's carbon footprint. This paper presents a model for a multi-objective collection-distribution center location and allocation problem in a closed loop supply chain for the beer industry, in which the objective is to minimize total costs and transportation pollution. Uncertainties in the form of randomness and fuzziness are jointly handled in this paper to ensure a more practical problem solution, for which returned bottle sand unusable bottles are considered fuzzy random variables. A heuristic algorithm based on priority-based global-local-neighbor particle swarm optimization (pb-glnPSO) is applied to ensure reliable solutions for this NP-hard problem. A case study on a beer operation company is conducted to illustrate the application of the proposed model and demonstrate the priority-based global-local-neighbor particle swarm optimization.

Obesity is a complex chronic disease characterized by excess of body fat. It represents a significant public health problem due to the health-related risk factors. There are growing evidences showing that maternal obesity can program the offspring, which influence neonatal phenotype and predispose offspring to a higher prevalence of metabolic disorders such as obesity. This increased risk may also be epigenetically transmitted across generations. Thus, there is an urgent need to find effective reprogramming approaches in order to resume normal fetal development. Polyphenols are bioactive compounds found in fruits and vegetables that exert their anti-obesity effect through its powerful anti-oxidant and anti-inflammatory activities. Polyphenols supplementation has been proven to counteract the deleterious effects of maternal obesity programming on offspring. Indeed, some polyphenols can cross the placenta and protect the fetal predisposition against obesity. The present review summarizes the effects of dietary polyphenols on obesity-induced maternal reprogramming as an offspring anti-obesity approach.

One of the most significant developments in the sports world over the last two decades has been the use of mathematical methods in conjunction with the massive amounts of data now available to analyze performances, identify trends and patterns, and forecast results. Football analytics has advanced significantly in recent years and continues to evolve as it becomes a more recognized and integral part of the game. Football analytics is also used to forecast game outcomes, allowing bettors to make educated guesses. This article describes mathematical concepts related to football analytics that enable a better betting strategies. We explain how the pitch is partitioned into different zones and we define possession sequences. Furthermore, we explain what an expected goals model is and which expected goals model we use in this research. Furthermore, we define two general characteristics of a player evaluation method, each corresponding to one of the equations of the Dawson model. Based on these characteristics, we describe the developments of several general approaches for evaluating players in the context of the Dawson model.

Contamination in coastal regions attributed to fluoride and nitrate cannot be disregarded, given the substantial environmental and public health issues they present worldwide. Maintaining water quality is crucial for environmental well-being. This comprehensive study was performed to assess the spatial as well as indexical water quality, identify contamination sources, and evaluate associated health risks pertaining to nitrate and flouride in AlHassa region, KSA. The physiochemical results revealed a pervasive pollution of the overall groundwater. The dominant water type was Na-Cl, indicating saltwater intrusion and reverse ion exchange impact. Spatiotemporal variations in physicochemical properties suggest diverse hydrochemical mechanisms, with geogenic factors primarily influencing groundwater chemistry. The groundwater pollution index varied between 0.8426 and 4.7172, classifying samples as moderately to very highly polluted. Similarly, the synthetic pollution index (in the range of 0.5021-4.0715) revealed that none of the samples had excellent water quality, with various degrees of pollution categories. Nitrate Health Quotient (HQ) values indicated chronic human health risks ranging from low to severe, with newborns being the most vulnerable. Household use of nitrate-rich groundwater for showering and cleaning did not pose significant health risks. Fluoride HQ decreased with age, and children faced the highest risk of fluorosis. The Hazard Index (HI) yielded moderate to high-risk values. Nitrate risks were 1.21 times higher than fluoride risks, as per average HI assessment. All samples fell into the vulnerable category based on the Total Hazard Index (THI), with 88.89% classified as very high risk. This research provides valuable insights into groundwater quality, guiding water authorities, inhabitants, and researchers in identifying safe water sources and vulnerable human populations. The results highlight the need for appropriate treatment techniques and long-term coastal groundwater management plans.

Background: Kidney transplantation is considered the first-choice therapy in ESRD patients. Despite recent improvements in terms of outcomes and graft survival in recipients, postoperative complications still concern health-care providers involved in the management of those patients. Particularly challenging are cardiovascular complications. Perioperative goal-directed fluid-therapy (PGDT) and hemodynamic optimization are widely used in high-risk surgical patients, and are associated with a significant reduction in postoperative complication rates and length of stay (LOS). The aim of this work is to compare the effects of perioperative goal-directed therapy (PGDT) with conventional fluid therapy (CFT), and to determine whether there are any differences in major postoperative complications rates and delayed graft function (DGF) outcomes. Methods: Prospective study with historical controls. Two groups, a PGDT- and a CFT- group were used: the stroke volume (SV) optimization protocol was applied in PGDT group throughout the procedure. Conventional fluid therapy with fluids titration at a central venous pressure (CVP) 8-12 mmHg and mean arterial pressure (MAP) >80mmHg was applied to the control-group. Postoperative data collection including vital signs, weight, urinary output, serum creatinine, blood urea nitrogen, serum potassium, and assessement of volemic status and the signs and symptoms of major postoperative complications occurred at 24h, 72h, 7 days and 30 days after transplantation. Results: Among the 66 patients enrolled, 33 were in each group and both groups had similar physical characteristics. Good fuctional recovery was evident in the 94% of patients. The statistical analysis has showed a difference in postoperative complications as follows: significant reduction of cardiovascular complications, DGF episodes (p<0.05) and surgical complications (p<0.01). There were no significant differences in pulmonary or other complication. Conclusions: PGDT and SV optimization effectively influenced the rate of major postoperative complications, reducing the overall morbidity and thus the mortality in patients receiving kidney transplantation.

There is much discussion regarding the Sustainable Development Goals’ (SDGs) capacity to promote inclusive development. While some argue that they represent an opportunity for collaborative goal-led and evidence-based governance, other voices express concerns as they perceive them as techno-managerial framework, that measures development according to quantitatively defined parameters and does not allow for local variation. We argue that the extent to which the positive or negative aspects of the SDGs prevail depends on the monitoring system’s ability to account for multiple and intersecting inequalities. Attention to the role of inequalities for SDG monitoring is of particular importance for SDG 11 due to the additional methodological challenge posed by the need for sub-nationally (urban) representative indicators – especially in cities with intra-urban inequalities related to socio-spatial variations among neighbourhoods. Investigating the extent to which its representativeness is vulnerable to inequalities we systematically analyse the current methodological proposals for the SDG 11 indicator framework. The outcome is a call for 1) a more explicit attention to intra-urban inequalities, 2) the development of a methodological approach to “recalibrate” the city-level indicators to account for the degree of intra-urban inequalities, and 3) an alignment between methodologies and data practices applied for monitoring SDG 11 and the extent of the underlying inequalities within the city that is being assessed. This would enable an informed decision regarding the trade-off in indicator representativeness between conventional data sources, such as censuses and household surveys, and emerging methods, such as participatory geospatial methods and citizen-generated data practices.

In the paper is described the control electronics for an industrial pneumatic – hydraulic system based on a low-cost PLC. The developed system is a hydraulic pulse system and it generates series of high pressure hydraulic pulses (max. 200 bar). We describe requirements, an overall concept of the embedded control system, user interface, security features and network connectivity. In the description of the software solution we describe implementation of hierarchical ordered program threads (multithreaded program) and main control state machine. At the conclusion, we describe the calibration method of the system and calibration curves and we present the schematic diagram and a photo of a functional prototype of the system.

Public restrooms are often a hub of microbial contamination, and the examination of bacterial contamination in these facilities can serve as an important indicator of the transmission of infectious diseases. This study was conducted to determine the prevalence of bacterial contamination in public restrooms based on the economic class of the building. Samples were collected from various spots in 32 restrooms found in 10 shopping malls, classifying them into two categories: upper-end restrooms and lower-end restrooms. The findings showed that the level of contamination was higher in the lower-end restrooms, with the seat being the most contaminated area. The most dominant Gram-positive bacteria were coagulase-negative staphylococci species, making up 86% of the identified Gram-positive isolates. The most dominant Gram-negative bacteria identified were Klebsiella pneumoniae and Pseudomonas aeruginosa. The antibiotic sensitivity test results revealed the presence of multi-drug resistant bacteria among the Gram-positive and negative isolates, including Staphylococcus haemolyticus, Staphylococcus kloosi, Acinetobacter baumanii, and Pseudomonas aeruginosa. In conclusion, the study underscores the significance of monitoring bacterial contamination in public restrooms and the need for measures to reduce the spread of infectious diseases. Further research is crucial to gain a complete understanding of the bacterial contamination in public restrooms and their resistance patterns, to ensure the safety and health of the public. The implementation of improved cleaning practices and hands-free designs in restrooms can help reduce the risk of cross-contamination and prevent the spread of diseases.

The weight coefficients of the diaphragm spring depend on experiences in the traditional optimization. However, this method not only cannot guarantee the optimal solution but it is also not universal. Therefore, a new optimization target function is proposed. The new function takes the minimum of average compress force changing of the spring and the minimum force of the separation as total objectives. Based on the optimization function, the result of the clutch diaphragm spring in a car is analyzed by the non-dominated sorting genetic algorithm (NSGA-II) and the solution set of Pareto is obtained. The results show that the pressing force of the diaphragm spring is improved by 4.09%by the new algorithmand the steering separation force is improved by 6.55%, which has better stability and steering portability. The problem of the weight coefficient in the traditional empirical design is solved. The pressing force of the optimized diaphragm spring varied slightly during the abrasion range of the friction film, and the manipulation became remarkably light.

Today, computer programming is an essential pillar in the education of individuals. Even though technological evolution has eased the massive need for computer programming, a systematic lit-erature review shows some problems remain with teaching computer programing. To address such issues, in this paper we propose an adapted theory, a method, and a model for teaching some knowledge objects associated with the concepts of variables, expressions, comparisons, loops, and functions in programming fundamentals in computer sciences. The main contribution of this study comprises the extension of the concept of didactic transposition to improve teaching in context; in this paper, the idea is called didactic transposition in extensa sensu. The proposal involves the development of a linguistic corpus based on syllabi, textbooks, reference manuals, and a survey applied to experts in teaching programming fundamentals based on seventy-eight universities worldwide. An adapted theory, a method, and a model for teaching programming fundamentals using computational linguistics are produced. In addition, a template is created for designing teaching practices in this regard. The proposal generates an important alternative for the devel-opment of teaching strategies where the conditions of the context are addressed as a priority; ad-ditionally, several aspects are considered for elaborating teaching strategies using computational linguistic techniques from written documents.

The article presents a new scalable iterative method for linear programming called the “apex method”. The key feature of this method is constructing a path close to optimal on the surface of the feasible region from a certain starting point to the exact solution of linear programming problem. The optimal path refers to a path of minimum length according to the Euclidean metric. The apex method is based on the predictor-corrector framework and proceeds in two stages: quest (predictor) and target (corrector). The quest stage calculates a rough initial approximation of linear programming problem. The target stage refines the initial approximation with a given precision. The main operation used in the apex method is an operation that calculates the pseudoprojection, which is a generalization of the metric projection to a convex closed set. This operation is used both in the quest stage and in the target stage. A parallel algorithm using a Fejér mapping to compute the pseudoprojection is presented. An analytical estimation of the parallelism degree of this algorithm is obtained. Also, an algorithm implementing the target stage is given. The convergence of this algorithm is proven. An experimental study of the scalability of the apex method on a cluster computing system is described. The results of applying the apex method to solve problems from the Netlib-LP repository are presented.

In this work, an algorithm for the scheduling of household appliances to reduce the energy cost and the peak-power consumption is proposed. The system architecture of a home energy management system (HEMS) is presented to operate the appliances. The dynamics of thermal and non-thermal appliances is represented into state-space model to formulate the scheduling task into a mixed-integer-linear-programming (MILP) optimization problem. Model predictive control (MPC) strategy is used to operate the appliances in real-time. The HEMS schedules the appliances in a dynamic manner without any a priori knowledge of the load-consumption pattern. At the same time, HEMS responds to the real-time electricity market and the external environmental conditions (solar radiation, ambient temperature etc). Simulation results exhibit the benefits of proposed HEMS by showing the reduction of up to 47% in electricity cost and up to 48% in peak power consumption.

Quantum computers are machines that are designed to use quantum mechanics in order to improve upon classical computers by running quantum algorithms. One of the main applications of quantum computing is solving optimization problems. For addressing optimization problems, we can use linear programming. Linear programming is a method to obtain the best possible outcome in a special case of mathematical programming. Application areas of this problem consist of resource allocation, production scheduling, parameter estimation, etc. In our study, we look at quantum speedup ratios of HHL Algorithm for different scenarios of linear programming. In a first scenario we look quantum speedup ratio (S(N)) as a function of phase transition and the ratio (κ) between the greatest and smallest eigenvalues of the matrix in linear equation system. As a second scenario, we investigate the changes in S(N) as a function of κ and s, which is the coefficient for defining the matrix as s-sparse.

This study explores optimizing Synthetic Aperture Radar (SAR) satellite constellation scheduling for multi-imaging missions in densely targeted areas using an in-house developed Modified Dynamic Programming (MDP) algorithm. By employing Mixed-Integer Linear Programming (MILP) to define the mission planning problem, the research aims to maximize observation of high-value targets within restricted planning horizons. Numerical simulations, covering a wide range of target numbers and satellite configurations, reveal the MDP algorithm’s superior mission allocation efficiency, enhanced success rates, and reduced revisit times, compared to the Greedy algorithm. The findings underscore the MDP algorithm’s improved operational efficiency and planning robustness for complex imaging tasks, demonstrating significant advancements over traditional approaches.

This study presents review of 7580 papers in 13 academic journals, published from January 2015 to January 2020. After a detailed analysis of all papers, 46 papers were further selected showing research on a student population aged between 6 and 15 years old. In order for the paper to be included in the research, the condition was that the paper deals with teaching at least one of the following content areas: programming languages, game design, computer thinking (CT), algorithmic thinking and robotics programming. This study shows the representation of the listed content area in reviewed papers for the specified time period as well as a detailed analysis of the selected papers. Available data about study, participants and education level, country (first author), learning domain, teaching tools, research questions, hypothesis, pre/post-test results, interviews, control groups, course duration, research design, previous experience, project or grant and re-search purpose in detected papers were analysed. In addition, impact of studying some of the listed content areas on student learning performance, motivation, attitude and perception were investigated.

Berberis vulgaris L. (Berberidaceae) is a shrub that has been widely used in European folk medicine as an anti-inflammatory and antimicrobial agent. The purpose of our study was to elucidate the mechanisms of antiproliferative action of the plant’s methanolic root extract (BVR) against colon cancer cells. Cytotoxicity and pro-apoptotic activity were determined in human colon adenocarcinoma cell lines (LS180 and HT-29) and control colon epithelial CCD841 CoN cells. According to the MTT assay, after 48 h of cell exposure, the IC50 values were as follows: 4.3; 46.1 and 50.2 µg/mL for LS180, HT-29, and CCD841 CoN cells, respectively, showing the greater sensitivity of cancer cells to BVR. The Cell Death Detection ELISAPLUS kit demonstrated that BVR induced programmed cell death only against HT-29 cells. RT-qPCR with relative quantification method showed significant changes in the expression of genes related to apoptosis in both colon cancer cell lines. The genes BCL2L1 (126.84-366.66%), BCL2L2 (277.08-330.12%), CASP3 (180.36-261.36%) and CASP9 (158.08-213.46%) had significantly elevated expression, while BCL2 (23.08-52.06%) had reduced expression. Furthermore, in a panel of antioxidant tests, BVR showed positive effects (63.93±0.01, 122.92±0.01, and 220.29±0.02 mg Trolox equivalents (TE)/g in the DPPH•, ABTS•+ and ORAC assays, respectively). In the lipoxygenase (LOX) inhibition test, BVR revealed 62,60±0.87% of enzyme inhibition. The chemical composition of BVR was determined using UHPLC-UV-CAD-MS/MS analysis and confirmed the presence of several known alkaloids, including berberine, as well as other alkaloids and two derivatives of hydroxycinnamic acid (ferulic and sinapic acid hexosides). This is the first such extensive assessment of the biological activity of BVR. The results are very promising and encourage for the use of BVR as a comprehensive chemopreventive agent (anti-inflammatory, antioxidant, and pro-apoptotic) in colorectal cancer.

Photogrammetry involves aerial photography of the earth’s surface and subsequently processing the images to provide a more accurate depiction of the area (Orthophotography). It’s used by the Spanish Instituto Geográfico Nacional to update road cartography but requires a significant amount of manual labor due to the need to perform visual inspection of all tiled images. Deep Learning techniques (artificial neural networks with more than one hidden layer) can perform road detection but it is still unclear how to find the optimal network architecture. Our system applies grammar guided genetic programming to the search of deep neural network architectures. In this kind of evolutive algorithm all the population individuals (here candidate network architectures) are constrained to rules specified by a grammar that defines valid and useful structural patterns to guide the search process. Grammar used includes well-known complex structures (e.g. Inception-like modules) combined with a custom designed mutation operator (dynamically links the mutation probability to structural diversity). Pilot results show that the system is able to design models for road detection that obtain test accuracies similar to that reached by state of the art models when evaluated over a dataset from the Spanish National Aerial Orthophotography Plan.

Abstract: Safety issues related to the electrification of more electric aircraft (MEA) need to be addressed because of the increasing complexity of aircraft electrical power systems and the growing number of safety-critical sub-systems that need to be powered. Managing the energy storage systems and the flexibility in the load-side plays an important role in preserving the system’s safety when facing an energy shortage. This paper presents a system-level centralized operation management strategy based on model predictive control (MPC) for MEA to schedule battery systems and exploit flexibility in the demand-side while satisfying time-varying operational requirements. The proposed online control strategy aims to maintain energy storage (ES) and prolong the battery life cycle, while minimizing load shedding, with fewer switching activities to improve devices lifetime and to avoid unnecessary transients. Using a mixed-integer linear programming (MILP) formulation, different objective functions are proposed to realize the control targets, with soft constraints improving the robustness of the model. Besides, an evaluation framework is proposed to analyze the effects of various objective functions and the prediction horizon on system performance, which provides the designers and users of MEA and other complex systems with new insights into operation management problem formulation.

Functional connectivity (FC) is a potential candidate that can increase the performance of brain-computer interfaces (BCIs) in the elderly because of its compensatory role in neural circuits. However, it is difficult to decode FC by current machine learning techniques because of a lack of its physiological understanding. To investigate the suitability of FC in BCI for the elderly, we propose the decoding of lower- and higher-order FCs using a convolutional neural network (CNN) in six cognitive-motor tasks. The layer-wise relevance propagation (LRP) method describes how age-related changes in FCs impact BCI applications for the elderly compared to younger adults. Seventeen younger (24.5±2.7 years) and twelve older (72.5±3.2 years) adults were recruited to perform tasks related to hand-force control with or without mental calculation. CNN yielded a six-class classification accuracy of 75.3% in the elderly, exceeding the 70.7% accuracy for the younger adults. In the elderly, the proposed method increases the classification accuracy by 88.3% compared to the filter-bank common spatial pattern (FBCSP). LRP results revealed that both lower- and higher-order FCs were dominantly overactivated in the prefrontal lobe depending on task type. These findings suggest a promising application of multi-order FC with deep learning on BCI systems for the elderly.

As the demands in reliability and high-degree of automation in industrial applications are increasing exponentially, the current Industry 4.0 trend lies in migrating towards smarter technologies that increase flexibility and provide autonomous operation. To tackle this, manufacturers shifted towards Real-Time Ethernet communication which supports autonomous operation, faster sensor/actuator configuration and high degree of determinism. Nevertheless, the uninterrupted operating principle of legacy industrial systems as well as the system complexity and heterogeneity constitutes the transition to Real-Time Ethernet very challenging. This article proposes a novel method allowing to automate the generation of executable code for Real-Time Ethernet architectures based on high-level programming models. The method is based on a programming model and modular code artifacts for the hardware architecture, employing Real-Time Ethernet communication. Through an tool-supported algorithm the high-level model is linked to the architecture's communication primitives and interfaces. The tool-support reduces significantly the development and debugging effort for Real-Time Ethernet applications and increases the application reliability, since the generated code is based on verified programming models. Additionally, the tool creates dedicated files, which allow automated industrial network configuration without any human intervention. Finally, by embedding firewall policies into the code generation process, the method guarantees cyber-resilience for the Real-Time Ethernet architecture. We demonstrate the proposed method in Programmable Logic Controllers (PLCs) of a Public Power Corporation's Hydroelectric Power Plant, which control the temperature and rotor speed of a power generator. The results demonstrate the method's ability to generate rapidly trustworthy and fault-tolerant code for the autonomous plant operation. The hurdles in time and effort for developing, configuring and debugging Real-Time Ethernet applications can be minimized through a high-level programming model that allows automated generation of executable code that is reusable for similar applications. Such time and effort reduction may pave the way towards the Industry 4.0 area.

Studies have shown that in many practical applications, data interpolation by splines leads to better approximation and higher computational efficiency as compared to data interpolation by a single polynomial. Data interpolation by splines can be significantly improved if knots are allowed to be free rather than at a priori fixed locations such as data points. In practical applications, the smallest possible curvature is often desired. Therefore, optimal splines are determined by minimizing a derivative of continuously differentiable functions comprising the spline of the required order. The problem of obtaining an optimal spline is tantamount to minimizing derivatives of a nonlinear differentiable function over a Banach space on a compact set. While the problem of data interpolation by quadratic splines has been accomplished analytically, interpolation by splines of higher orders or in higher dimensions is challenging. In this paper, to overcome difficulties associated with the complexity of the interpolation problem, the interval over which data points are defined, is discretized and continuous derivatives are substituted by their discrete counterparts. It is shown that as the mesh of the discretization approaches zero, a resulting near-optimal spline approaches an optimal spline. Splines with the desired accuracy can be obtained by choosing an appropriate mesh of the discretization. By using cubic splines as an example, numerical results demonstrate that the linear programming (LP) formulation, resulting from the discretization of the interpolation problem, can be solved by linear solvers with high computational efficiency and resulting splines provide a good approximation to the optimal splines.

This paper proposes a model based on gene expression programming for predicting discharge coefficient of triangular labyrinth weirs. The parameters influencing discharge coefficient prediction were first examined and presented as crest height ratio to the head over the crest of the weir (p/y), crest length of water to channel width (L/W), crest length of water to the head over the crest of the weir (L/y), Froude number (F=V/√(gy)) and vertex angle () dimensionless parameters. Different models were then presented using sensitivity analysis in order to examine each of the dimensionless parameters presented in this study. In addition, an equation was presented through the use of nonlinear regression (NLR) for the purpose of comparison with GEP. The results of the studies conducted by using different statistical indexes indicated that GEP is more capable than NLR. This is to the extent that GEP predicts the discharge coefficient with an average relative error of approximately 2.5% in such a manner that the predicted values have less than 5% relative error in the worst model.

This paper introduces an application of R programming language for geostatistical data processing with a case study of the Mariana Trench, Pacific Ocean. The formation of the Mariana Trench, the deepest among all hadal oceanic depth trenches, is caused by complex and diverse geomorphic factors affecting its development. Mariana Trench crosses four tectonic plates: Mariana, Caroline, Pacific and Philippine. The impact of the geographic location and geological factors on its geomorphology has been studied by methods of statistical analysis and data visualization using R libraries. The methodology includes following steps. Firstly, vector thematic data were processed in QGIS: tectonics, bathymetry, geomorphology and geology. Secondly, 25 cross-section profiles were drawn across the trench. The length of each profile is 1000-km. The attribute information has been derived from each profile and stored in a table containing coordinates, depths and thematic information. Finally, this table was processed by methods of the statistical analysis on R. The programming codes and graphical results are presented. The results include geospatial comparative analysis and estimated effects of the data distribution by tectonic plates: slope angle, igneous volcanic areas and depths. The innovativeness of this paper consists in a cross-disciplinary approach combining GIS, statistical analysis and R programming.

Toxoplasmosis is a zoonosis of warm-blooded animals, affecting also humans, caused by Toxo-plasma gondii, an obligate intracellular parasite with a complex biological cycle. Toxoplasmosis is considered a re-emerging zoonosis and an important public health threat, also for the absence, up to now, of efficient vaccines and preventive measures. Sources of transmission to humans are environmental or food-borne, mainly through the consumption of raw and undercooked meat, predominantly of Sus scrofa, considered highly susceptible to T. gondii. Mainly in the last dec-ades, an effective strategy to counter animal infectious diseases was based on the discovery of resistance immuno-genetic markers, possibly to be used for association studies between geno-typic and phenotypic traits and consequently in Marker Assisted Selection. Until now, this gen-otyping approach has never been adopted for T. gondii infection, so this study aimed, for the first time, to fill this gap. In particular, pigs, reared in different farms of Central Italy, were serologically characterized by an ELISA assay performed on diaphragm meat juice. Out of 179 tested animals, 98 resulted seropositive (54.74%), 57 seronegative (31.84%) and 24 doubtful (10.6%), underlining a possible re-emerging diffusion of this protozoan in the investigated areas. Atten-tion was firstly focused on IL-18 gene, encoding for a pro-inflammatory cytokine that plays a key role starting from the upstream steps of the immunity pathway towards T. gondii. A RT-PCR assay followed by Sanger sequencing of IL-18 cDNA was de novo developed. For this interleukin, at this stage, genetic analysis has not highlighted significant polymorphic variations compared to the reference sequence, except for a seropositive animal. However, the outcomes of this pre-liminary innovative study will be investigated in depth analyzing other relevant genetic re-gions and other target genes.

This paper presents experimental identification and vibration suppression of a flexible manipulator with non-collocated piezoelectric actuators and strain sensors using optimal multi-poles placement control. To precisely identify the system model, a reduced order transfer function with relocated zeros is proposed, and a first-order inertia element is added to the model to compensate the non-collocation. Comparisons show the identified model match closely with the experimental results both in the time and frequency domains, and a fit of 97.2% is achieved. Based on the identified model, a full-state multi-poles placement controller is designed, and the optimal locations of the closed loop poles are determined. The feasibility of the proposed controller is validated by simulations. Moreover, the controller is tested for different locations of the closed loop poles, and an excellent performance of the optimal locations of the closed loop poles is shown. Finally, the effectiveness of the proposed controller is demonstrated by experiments. Results show that the vibrations of the expected modes are significantly diminished. Besides, vibrations of the higher modes are also slightly suppressed. Accordingly, multi-mode vibrations of the manipulator are well attenuated, and the tip displacement converges quickly with the proposed method.

The feasibility of recovering bioactive antioxidants from Phyllantus emblica leaves using ethanol -water mixture (0 – 100%) and heat-assisted extraction technology (HAE-T) was investigated in this present study. To this effect, the process parameter of operating temperature (OT: 30 -50 oC), solid -to-liquid ratio (S:L: 1:20 - 1:60 g/mL) and extraction time (ET: 45 - 180 min) were investigated on the extract total phenolic content (TPC, mg GAE/g d.w), yield (EY, %) and antioxidant activity (μM AAE/g d.w) by employing the Box-Behnken experimental design (BBD) available in response surface methodology (RSM). Multi-objective process optimization using the desirability function algorithm to determine set of process variables that simultaneously optimize process responses of TPC, EY and AA was also investigated. The recovery process was thereafter modeled with BBD-RSM and multi gene genetic programming (MGGP) algorithm and model reliability assessment via Monte Carlo simulation were conducted for the best performing set of models for predicting TPC, EY and AA values. The HPLC characterization of the recovered extract was carried out to ascertain the phenolic compound constituents of the Phyllantus emblica leaf extract. The 50% ethanol solution was found to be the best for the optimal extraction of antioxidants from Phyllantus emblica leaves. The HAE-T was suitable for recovering bioactive extract from Phyllantus emblica leaves and investigated process parameters have impacts on the recovery process. The process parameters that simultaneously gave the optimum EY of 21.6565%, TPC of 67.116 mg GAE/g and AA of 3.68583 µM AAE/g were OT of 41.61 oC, S:L of 1:60 g/mL and ET of 180 min. The HPLC extract profiling revealed that the bioactive constituents present in the recovered extract were betulinic acid, gallic acid, chlorogenic acid, caffeic acid, ellagic acid, and ferulic acid. Both the developed BBD-RSM and evolved MGGP-based models predicted the observed process response of TPC, EY and AA satisfactorily with BBD-RSM models marginally better in their predictions. The reliability results showed that the BBD-RSM models predicted TPC, EY and AA values with high certainty of 99.985%, 97.569% and 98.661%, respectively.

The connectivity level of last-generation vehicles is constantly on the rise. The combined use of Vehicle-To-Everything (V2X) connectivity and autonomous driving can provide remarkable benefits through the optimization of the route and speed trajectory. In this framework, this paper focuses on vehicle eco-driving optimization in a connected environment. The virtual test rig of a premium segment passenger car was used for generating the simulation scenarios. The benefits, in terms of energy and time savings, that the introduction of V2X communication, integrated with cloud computing, can have in a real-world scenario were assessed. The Reference Scenario is a pre-defined Real Driving Emissions (RDE) compliant route, while the simulation scenarios were generated by assuming two different penetration levels of V2X technologies. The associated energy minimization problem is formulated and solved by means of a global optimization algorithm, i.e., Dynamic Programming (DP). The optimization framework includes information coming from the surrounding environment, e.g., traffic lights state, speed limits, distance to travel, etc. The simulations show that introducing a smart infrastructure along with optimizing the vehicle speed in a real-world route can potentially reduce the required energy by 54% while shortening the travel time by 38%. Finally, a sensitivity analysis is performed on the bi-objective optimization cost function to find a set of Pareto optimal solutions, between energy and travel time minimization.

The eutrophication of open water bodies, especially in coastal water area, has received intensive public focuses in recent years. Biological treatment of organic pollutants in industrial and domestic wastewater requires microbial flora to participate. The environmental impact of these microbes, particularly in regard to the spread of antibiotic resistance genes and pathogenicity in coastal water, remains largely unknown. We initiate studies to examine antibiotic resistance genes (ARGs) in microbial flora and study the mode of antibiotic spread in the coastal waters of Bohai Bay, North China by using high performance liquid chromatography-mass spectrum analysis and quantitative polymerase chain reaction. The metabolic features of bacteria related to the presence of ARGs in the coastal area showed the enrichment of Pseudomonadale species with triple resistance properties (ampicillin, kanamycin and gentamycin) at the estuary site locating adjacent to a coastal sewage treatment plant where both type I and type II polyketide synthase genes and b-lactam type antibiotics are detected. Pseudomonadale order is phylogenetically belonged to Proteobacteria Phylum, Gamma-proteobacteria Class and contains Pseudomonadaceae family and Pseudomonas genus. QPCR analysis suggests that the percent occupation of Pseudomonadale species to total Proteobacteria in the examined stations is close to several sampling stations close to sewage treatment plants, where consistent release of organic wastes occurred.

In this paper, we propose a method to find all efficient solutions of an interval multiple objective linear programming (IMOLP) problem with interval coefficients in the objective functions, the constraint matrix and the right-hand side vector. The set of all efficient solutions of an IMOLP problem can completely supply information to the decision makers in finding their most preferred solutions but, up to now, not all efficient solutions of an IMOLP problem can be found by known methods. A numerical example is given to illustrate the working of the proposed method.

Feature selection is predominantly used in machine learning tasks, such as classification and regression. It selects a subset of features (relevant attributes of data points) from a larger set that contributes as optimally as possible to the informativeness of the model. There are exponentially many subsets of a given set, and thus, the exhaustive search is only practical for problems with at most a few dozen features. In the past, there have been attempts to reduce the search space using dynamic programming. However, models that consider similarity in pairs of features besides the quality of individual features do not provide the required optimal substructure. As a result, algorithms, which we will call suboptimal dynamic programming algorithms, find a solution that may deviate significantly from the optimal one. In this paper, we propose a dynamic programming algorithm with an iterative upgrade where the order of feature processing is inverted in each iteration. Such an alternating approach allows for improving the optimization function by using the score from the previous iteration to estimate the contribution of unprocessed features. The iterative process is proven to converge and terminate when the solution does not change in three successive iterations or when the number of iterations reaches the threshold. Results in more than 90 % of tests align with those of the exhaustive search, being competitive and often superior to the reference greedy approach. The validation was done by comparing the scores of output feature subsets and examining the accuracy of different classifiers learned on these features. In the context of feature selection, the proposed algorithm can be characterized as a filter method. However, we expect that the idea of alternating suboptimal optimization will soon be generalized to tasks beyond feature selection.

We study the efficient computation of power indices for weighted voting games with precoalitions amongst subsets of players (reflecting, e.g., ideological proximity) using the paradigm of dynamic programming. Starting from the state-of-the-art algorithms for computing the Banzhaf and Shapley-Shubik indices for weighted voting games we present a framework for fast algorithms for the three most common power indices with precoalitions, i.e. the Owen index, the Banzhaf-Owen index and the Symmetric Coalitional Banzhaf index, and point out why our new algorithms are applicable for large numbers of players. We discuss implementations of our algorithms for the three power indices with precoalitions in C++ and review computing times as well as storage requirements.

Appropriate estimation of soil settlement is of significant importance since it directly influences the performance of building and infrastructures that are built on soil. In particular, the settlement of fine-grained soils is critical because of low permeability and continuous settlement with time. Coefficient of consolidation (Cc) is a key parameter to estimate settlement of fine-grained soil layers. However, estimation of this parameter is time consuming, needs skilled technicians, and specific equipment. In this study, Cc was estimated using several soil parameters such as liquid limit (LL), plastic limit (PL), and initial void ratio (e0). Estimating such parameters in laboratory is straight forward and needs substantially less time and cost compared to conventional tests to estimate Cc such as Oedometer test. This study presents a novel prediction model for Cc of fine-grained soils using gene-expression programming (GEP). GEP is a biologically inspired technique capable of offering closed-form solution for the optimal solution. A database consisted of 108 different data points was used to develop the model. A closed-form equation solution was derived to estimate Cc based on LL, PL, and e0. The performance of developed GEP-based model was evaluated through coefficient of determination (R2), root mean squared error (RMSE), and mean average error (MAE). High R2 and low error values indicated the descent performance of the model. Furthermore, the model was evaluated using the additional performance measures and met all the suggested criteria. Furthermore, the model had a better performance in terms of R2, RMSE, and MAE compared to most of existing models. It is expected that the developed model will decrease the time and cost associate with determining Cc of fine-grained soils.