An active power dispatch method for a microgrid (MG) with multi-type loads, renewable energy sources (RESs) and distributed energy storage devices (DESDs) is the focus of this paper. The MG operates in a grid-connected model, and distributed power sources contribute to the service for load demands. The outputs of multiple DESDs are controlled to optimize the active power dispatch. Our goal with optimization is to reduce the economic cost under time-of-use (TOU) price, and to adjust the excessively high or low load rate of distributed transformers (DTs) caused by the peak-valley demand and load uncertainties. To simulate a practical environment, the stochastic characteristics of multi-type loads are formulated. The transition matrix of system state is provided. Then, a finite-horizon Markov decision process (FHMDP) model is established to describe the dispatch optimization problem. A learning-based technique is adopted to search the optimal joint control policy of multiple DESDs. Finally, simulation experiments are performed to validate the effectiveness of the proposed method, and the fuzzification analysis of the method is presented.

This paper is devoted to the study of multi-dimensional integral transform with Fox H-function in the kernel in weighted spaces integrable functions in the domain R+n with positive coordinates. Mapping properties such as the boundedness, the range, the representations of the considered transformation are established.

Abstract: Congenital cytomegalovirus (cCMV) infection poses significant risks to fetal development, particularly affecting the nervous system. This study reports a fetal autopsy case, examining cCMV infection and focusing on CMV DNA measurements in various fetal organs before formalin fixation, a novel approach for comprehensive CMV DNA evaluations in fetal organs affected by cCMV. A 20-week-old male fetus was diagnosed with cCMV following the detection of CMV DNA in ascites obtained via abdominocentesis in utero. After termination of pregnancy, multiple organs of the fetus, including the cerebrum, thyroid gland, heart, lungs, liver, spleen, kidneys, and adrenal glands, were extracted and examined for CMV DNA loads using real-time polymerase chain reaction. Histopathological examination involved hematoxylin-eosin and CMV-specific immunostaining. A correlation was found between CMV DNA loads and pathology, with higher CMV-infected cell numbers observed in organs positively identified with both staining methods, exhibiting CMV DNA levels of ≥1.0 × 104 copies/mL, compared to those detected solely by CMV-specific immunostaining, where CMV DNA levels ranged from 1.0 x 103 to 1.0 x 104 copies/mL. These results highlight a quantifiable relationship between organ infection extent and CMV DNA concentration, providing insights into cCMV pathogenesis and potentially informing future diagnostic and therapeutic strategies for cCMV infection.

To improve the accuracy of short-term multi-energy load prediction models for integrated energy systems, the historical development law of the multi-energy loads must be considered. Moreover, understanding the complex coupling correlation of the different loads in the multi-energy systems and accounting for other load-influencing factors, such as weather, may further improve the forecasting performance of such models. In this study, a two-stage fuzzy optimization method is proposed for the feature selection and identification of the multi-energy loads. To enrich the information content of the prediction input feature, we introduced a copula correlation feature analysis in the proposed framework, which extracts the complex dynamic coupling correlation of multi-energy loads and applies Akaike information criterion (AIC) to evaluate the adaptability of the different copula models presented. Furthermore, we combined a NARX neural network with Bayesian optimization and an extreme learning machine model optimized using a genetic algorithm to effectively improve the feature fusion performances of the proposed multi-energy load prediction model. The effectiveness of the proposed short-term prediction model was confirmed by the experimental results obtained using the multi-energy load time-series data of an actual integrated energy system.

In this paper, a new approach to the sliding-mode control of single-phase inverters under linear and non-linear loads is introduced. The main idea behind this approach is to utilize a non-linear, flexible and multi-slope function in controller structure. This non-linear function makes the controller possible to control the inverter by a non-linear multi-slope sliding surface. In general, this sliding surface has two parts with different slopes in each part and the flexibility of the sliding surface makes the multi-slope sliding-mode controller (MSSMC) possible to reduce the total harmonic distortion, to improve the tracking accuracy, and to prevent overshoots leading to undesirable transient-states in output voltage which are occurred when the load current sharply rises. In order to improve the tracking accuracy and to reduce the steady-state error, an integral term of the multi-slope function is also added to the sliding surface. The improved performance of the proposed controller is confirmed by simulations and finally, the results of the proposed approach are compared with a conventional SMC and a SRFPI controller.

This article introduces an innovative design method for public lighting systems that surpasses the limitations of conventional approaches, which rely on predefined lamp characteristics and spatial arrangement. By employing a multi-criteria decision algorithm, our study proposes an optimal design methodology considering several key aspects, including the distance between lamps, their type, power, and light distribution. The goal is to achieve optimal illumination that enhances visibility on public roads for drivers and pedestrians while simultaneously minimizing glare, installation costs and maximizing energy efficiency. The proposed methodology is implemented through an algorithm developed in Matlab, with results validated through simulations in Dialux. This information is used to construct a decision matrix, assessed using the CRITIC method across 180 different scenarios within a specific case study. The findings demonstrate the effectiveness of multi-criteria decision-making as a tool for significantly improving the planning and design of lighting in public illumination systems, allowing for selecting the optimal combination of parameters that ensure the best lighting conditions.

In this paper, we consider a new class of polynomials which is called the multi-poly-Euler polynomials. Then, we investigate their some properties and relations. We provide that the type 2 degenerate multi-poly-Euler polynomials equals a linear combination of the degenerate Euler polynomials of higher order and the degenerate Stirling numbers of the first kind. Moreover, we provide an addition formula and a derivative formula. Furthermore, in a special case, we acquire a correlation between the type 2 degenerate multi-poly-Euler polynomials and degenerate Whitney numbers.

Inspired by the definition of degenerate multi-poly-Genocchi polynomials given by using the degenerate multi-polyexponential functions. In this paper, we consider a class of new generating function for the degenerate multi-poly-Bernoulli polynomials, called the type 2 degenerate multi-poly-Bernoulli polynomials by means of the degenerate multiple polyexponential functions. Then, we investigate their some properties and relations. We show that the type 2 degenerate multi-poly-Bernoulli polynomials equals a linear combination of the weighted degenerate Bernoulli polynomials and Stirling numbers of the first kind. Moreover, we provide an addition formula and a derivative formula. Furthermore, in a special case, we acquire a correlation between the type 2 degenerate multi-poly-Bernoulli numbers and degenerate Whitney numbers.

Crop-type mapping is an important intermediate step for cost-effective crop management at the field level, as an overview of all fields with a particular crop type can be used for monitoring or yield forecasting, for instance. Our study used a data set with 2400 fields and corresponding satellite observations from the federal state of Bavaria, Germany. The study classified corn, winter wheat, winter barley, sugar beet, potato, and winter rapeseed as the main crops grown in Upper Bavaria. We additionally experimented with a rejection class "Other", which summarised further crop types. Corresponding Sentinel-2 data included the normalised difference vegetation index (NDVI) and raw bands from 2016 to 2018 for each selected field. The influence of raw bands compared to NDVI was analysed and the classification algorithms, i.e. support vector machine (SVM) and random forest (RF), were compared. The study showed that the use of an index should be critically questioned and that raw bands provided a wider spectral bandwidth, which significantly improved the mapping of crop types. The results underline the use of RF with raw bands and achieved overall accuracies (OA) of up to 92%. We also predicted crop types in an unknown year with significantly different weather conditions and several months before the end of the growing season. Thus, the influence of climate anomalies and the accuracy depending on the time of prediction were assessed. The crop types of a test site and year without labels could be determined with an OA of up to 86%. The results demonstrate the usefulness of the proof-of-concept and its readiness for use in real applications.

To conduct high-precision and high-resolution numerical simulation of complex flow structures in turbomachinery, a high-order finite volume weighted essentially non-oscillatory (WENO) scheme for the large eddy simulation (LES) is improved and embedded into the three-dimensional viscous unsteady CFD solver NUAA-Turbo. Firstly, the spectral characteristics and unsteady convergence of the improved WENO scheme are studied. Compared with the classical WENO scheme, the improved WENO scheme has better dissipation and dispersion characteristics and faster convergence speed. Then, the coefficient CW of the Wall-Adapting Local Eddy-viscosity (WALE) model is calibrated by decaying homogeneous isotropic turbulence (DHIT) test case. Finally, the scheme is applied to conduct high-precision LES calculations of turbulent boundary layer flow, supersonic compression corner flow, and low-pressure turbine cascade separation flow. The numerical simulation results show that this WENO scheme has excellent shock wave capture ability and turbulence resolution and can capture more flow field details with less mesh size, greatly reducing the computational cost and laying a foundation for large-scale engineering application of LES.

The building envelope has the most significant contribution in the reduction of the building energy consumption. Application of new, alternative and improved materials and systems has an important impact on the buildings performances. This paper is focused on the thermal transmittance, as an indicator of the thermal conductance of the construction element. It includes comparisons of the U-values, calculated by software, with those measured in situ on three representative façade walls. The walls have been constructed with the new wall system Fragmat NZ-1, a new product in Macedonian buildings. This research provides basic information on the thermal transmittance of the system. The results of the analysis show that the in situ measuring is a useful tool in validation of the precision of analytically calculated values, since it was difficult to obtain precise results from the analytical calculations only, especially when the layers are with non-uniform thickness.

This paper concentrates on the general birth-death processes with two different types of catastrophes. The Laplace transform of transition probability function for birth-death processes with two-type catastrophes are is successfully expressed with the Laplace transform of transition probability function of the birth-death processes without catastrophe. The first effective catastrophe occurrence time is considered. The Laplace transform of its probability density function, expectation and variance are obtained.

This paper studies the maximum reliability of multi-hop relay UAV, in which UAV provides wireless services for remote users without direct communication link on the ground as a coded cooperative relay. In this paper, the analytical expressions of total power loss and total bit error rate are derived as reliability measures. Firstly, based on the environmental statistical parameters, a LOS probability model is proposed. Then the problem of minimizing the bit error rate of static and mobile UAVs is studied. The goal is to minimize the total bit error rate by jointly optimizing the height, elevation, power and path loss, and subject to the maximum allowable path loss con-straints, transmission power allocation constraints and UAV height and elevation constraints. At the same time the total path loss is minimized to achieve maximum ground communication cov-erage. However, the formulated joint optimization problem is non-convex and generally difficult to solve. Therefore, we decomposed the problem into two subproblems and proposed an effective joint optimization iteration algorithm. Finally, the simulation results are given, and the analysis shows that the optimal height of different reliability measures is slightly different, and using the mobility of UAVs can improve the reliability of communication performance.

In this paper, a new axial-type magnetic gear with auxiliary flux-enhancing structure (AFS-AMG) is proposed. Compared to conventional AFS-AMG, it has the higher torque density and higher permanent magnet (PM) utilization factor. Firstly, the design rules and operating principles of proposed AFS-AMG are elaborated. Then, the mapping relation between the radial-type magnetic gears (RMGs) and AMGs are elucidated. Compared to its counterpart in RMGs, AFS-AMGs achieve small size. Then, the geometrical parameters of AFS-AMGs are optimized to obtain the better electromagnetic performances, where the torque density per volume and per PM volume is adopted as the evaluation standard. Finally, three different AMG topologies are constructed in finite element analysis (FEA) software for comparison. It is proven that the AFS-AMG has the largest torque density per volume and per PM volume.

The paper presents a review of currently available evaluations of the effects of continuously increasing anthropogenic loads on water resources. The increase in the fluxes of elements and compounds into the environment, such as the emission of greenhouse gases and dispersion of nutrients (nitrogen and phosphorus), acidifying gases, and toxic elements and compounds that adversely affect the water quality are considered. The significance of fresh waters as a life support factor of the human populations is demonstrated. Examples are presented to illustrate how key anthropogenic induced processes develop in land waters under the effect of anthropogenic loads, as exemplified by the Russian Kola regions. Climate warming and the increasing dispersion of elements are demonstrated to result in the eutrophication of surface waters even in areas remote from anthropogenic impacted regions. Although the emissions of acidifying gases diminish, the waters are still acidified in acid-vulnerable areas, and the chemical compositions of the waters have been significantly modified over the past decades, which indicates that the changes in the chemical composition of the waters are of irreversible. A new feature of the waters is distinguished: the toxicity of the habitats for aquatic organisms. Arguments are presented for establishing a theoretical approach for evaluating critical loads.

In this paper, we study the well-posedness and asymptotics of a one-dimensional thermoelastic laminated beam system either with or without structural damping, where the heat conduction is given by Fourier's law effective in the rotation angle displacements. We show that the system is well-posed by using Lumer-Philips theorem, and prove that the system is exponentially stable if and only if the wave speeds are equal, by using the perturbed energy method and Gearhart-Herbst-Prüss-Huang theorem. Furthermore, we show that the system with structural damping is polynomially stable provided that the wave speeds are not equal, by using the second-order energy method.

Wideband signal detection is an important problem in wireless communication. With the rapid development of deep learning (DL) technology, some DL-based methods are applied to wireless technology, and the effect is obvious. In this paper, we propose a novel neural network for multi-type signal detection that can locate signals and recognize signal types in wideband spectrogram. Our network utilizes the key point estimation to locate the rough centerline of signal region and identify class. Then, several regressions are carried out to achieve properties, such as local offset and border offsets of bounding box, which is further synthesized for a more fine location. Experimental results demonstrate that our method performs more accurate than other DL-based object detection methods previously employed for the same detection task. Specifically, our method runs obviously faster than existing methods, and abandons the anchor generation, which makes it more favorable for real-time applications.

Earth observation satellites can capture images of specific areas in Earth's orbit based on user requirements. Despite the high demand for satellite imagery, satellites remain a scarce resource. When there are many observation tasks that are large and dense, they may interfere with each other due to satellite mobility. To address this issue, a multi-satellite scheduling algorithm based on a task merging mechanism has been proposed. This paper proposes a two-stage approach to the problem: task merging phase and merging task scheduling phase. The task merging phase introduces two methods based on Mean Shift and Complete Graph to generate the merging task set. In the merging task scheduling phase, a multi-satellite scheduling algorithm based on merging tasks is employed to solve the problem. Finally, certain measurement experiments suggest the effectiveness of the algorithm.

The assortment of low-cost 3D printers for “in-practice” use, e.g., for clear aligner therapies, is ever increasing. To address concerns about the accuracy of orthodontic models produced on such printers when cost efficient modes of 3D printing are employed, this study examined the effect of print model body type and print angulation on accuracy. Six printing-configuration groups were included: 2 model types (solid or hollow shell) combined with 3 print angles (0°, 70°, or 90°) with 10 models/group; all models were printed with 100-µm layer thickness using a digital light processing-based 3-dimensional printer. Eleven selected structures and distances were measured on the printed models with a digital microscope and compared to the same measures on a digitized master model. The clinically-acceptability range was set at ±0.25 mm difference from the master model for single tooth measurements (intra-tooth) and ±0.5 mm for cross-arch measurements (inter-tooth). For individual measurements across all models, 98% fell within clinical acceptability. For mean measurements within each model group, only canine height for the shell-0° model had a mean difference (0.26 mm ± 0.03) outside the clinically acceptable range for intra-tooth measurements. Standard deviations for all intra-tooth measurements were within 0.07 mm. While none of the mean inter-tooth measurements exceeded the acceptability range, the standard deviations were larger (0.04 to 0.30 mm). Accuracy of orthodontic models for clear aligner therapies was not impacted beyond the clinically acceptable range when altering model body type and print angulation to improve efficiency of 3D printing. These findings suggest greater flexibility of the practitioner to alter print settings to address time and cost efficiency in various clinical scenarios and still maintain clinically acceptable model accuracy.

Railway has been used as one of the most crucial means of transportation in public mobility and economic development. For efficiently operating railways, the electrification system in railway infrastructure, which supplies electric power to trains, is essential facilities for stable train operation. Due to its important role, the electrification system needs to be rigorously and regularly inspected and managed. This paper presents a supervised learning method to classify Mobile Laser Scanning (MLS) data into ten target classes representing overhead wires, movable brackets and poles, which are recognized key objects in the electrification system. In general, the layout of railway electrification system shows a strong regularity of spatial relations among object classes. The proposed classifier is developed based on Conditional Random Field (CRF), which characterizes not only labeling homogeneity at short range, but also the layout compatibility between different object classes at long range in the probabilistic graphical model. This multi-range CRF model consists of a unary term and three pairwise contextual terms. In order to gain computational efficiency, MLS point clouds is converted into a set of line segments where the labeling process is applied. Support Vector Machine (SVM) is used as a local classifier considering only node features for producing the unary potentials of CRF model. As the short-range pairwise contextual term, Potts model is applied to enforce a local smoothness in short-range graph. While, long-range pairwise potentials are designed to enhance spatial regularities of both horizontal and vertical layouts among railway objects. We formulate two long-range pairwise potentials as the log posterior probability obtained by Naïve Bayes classifier. The directional layout compatibilities are characterized in probability look-up tables which represent co-occurrence rate of spatial relations in horizontal and vertical directions. The likelihood function is formulated by multivariate Gaussian distributions. In the proposed multi-range CRF model, the weight parameters to balance four sub-terms are estimated by applying the Stochastic Gradient Descent (SGD). The results show that the proposed multi-range CRF can effectively classify detailed railway elements, representing the average recall of 97.66% and the average precision of 97.07% for all classes.

ABSTRACT Purpose: Tongue image analysis for disease diagnosis is an ancient traditional non-invasive diagnosis technique widely used by traditional medicine practitioners. Deep Learning based multi-label disease detection models offer tremendous potential to clinical decision support systems, by facilitating preliminary diagnosis. Methods: In this work, we propose a multi-label disease detection pipeline, where in observation and analysis of tongue images captured and received via smartphones assist in predicting the health status of an individual. All images are voluntarily given by subjects consulting collaborating physicians. Images thus acquired are first and foremost classified either into a diseased or a normal category by a 5-fold cross-validation algorithm using a convolution neural network (MobileNetV2) model for binary classification. Once the diseased label is predicted, the image is used to diagnose multiple diseases using the prediction algorithm based on DenseNet121. Results: Average accuracy of 93 % was achieved in classifying diseased from normal healthy tongue by detection model with MobileNetV2 architecture. Multilabel disease classification produced more than 90% accurate results for the seven class labels considered. Conclusion: AI based image analysis shows promising results and an extensive dataset could provide further improvements to this approach. Rather than employing high-cost sophisticated image capturing setup, experimenting with smartphone images opens opportunity to provide preliminary health status to individuals on smartphone prior to further line of treatment and diagnosis.

Keywords: olfactory rehabilitation; chronic pain; fMRI;

Concrete is more stable than filler as a false roof in a downward approach type infill quarry, but the mechanical model of a concrete false roof is not clear. As a result, there has been limited application. Therefore, it is necessary to establish the mechanical model of a concrete artificial false roof to enhance the stability of the downward approach infill quarry. This paper combines theoretical analysis, model derivation, finite element analysis and field application methods. Firstly, the basic assumptions of thin plate theory and elasticity mechanics are used as the premise to establish the differential equations of the deflection curve of the concrete thin plate false roof. Then, the three types of bending moment generation of the concrete thin plate false roof are explored. Secondly, the relationship between the location of dangerous surface and dangerous point in hard-supported weak-slab structure and soft-supported weak-slab structure is analyzed, and the type of uniform load and calculation model of concrete thin-slab false roof are improved. Finally, according to the established mechanical model of thin slab false roof, finite element analysis and field application were carried out. The results show that there are three types of deflection curve differential equations in the concrete thin slab false roof perpendicular to the strike, and three extreme points exist in the middle section of the thin slab and on both sides of the surrounding rock. The hazardous surface of the hard-supported weak-slab structure is present at the intersection of the encircling rock and the thin-slab fake ceiling, with the perilous point situated on the top of this surface. The hazardous surface of the soft-supported weak-slab structure can be found in the centre section of the thin-slab fake ceiling, with the perilous point being located at the bottom of this surface. Moreover, the damage mode for both structures is that of maximum tensile stress damage. Upon conducting a finite element analysis, the results indicate that the concrete's maximum tensile stress is significantly high.

This paper proposes a new approach for multi-focus images fusion based on Region Mosaicing on Contrast Pyramids (REMCP). A density-based region growing method is developed to construct a focused region mask for multi-focus images. The segmented focused region mask is decomposed into a mask pyramid, which is then used for supervised region mosaicking on a contrast pyramid. In this way, the focus measurement and the continuity of focused regions are incorporated and the pixel level pyramid fusion is improved at the region level. Objective and subjective experiments show that the proposed REMCP is more robust to noise than compared algorithms and can fully preserves the focus information of the multi-focus images meanwhile reducing distortions of the fused images.

Attribute reduction is a core technique in the rough set domain and an important step in data preprocessing. Researchers have proposed numerous innovative methods to enhance the capability of attribute reduction, such as the emergence of multi-granularity rough set models, which can effectively process distributed and multi-granularity data. However, these innovative methods still have many shortcomings, such as how to deal with complex constraints and how to perform multi-angle effectiveness evaluations. Based on the multi-granularity model, this study proposes a new method of attribute reduction, namely using multi-granularity neighborhood information gain ratio as the measurement criterion. This method combines both supervised and unsupervised perspectives, and by integrating multi-granularity technology with neighborhood rough set theory, constructs a model that can adapt to multi-level data features. This model can select the optimal granularity level or attribute set according to the requirements. Finally, the proposed method is experimented with on 15 UCI datasets against six other attribute reduction algorithms. The experimental outcomes, upon analysis and comparative review, substantiate the reliability and consistency of the attribute reduction approach introduced in this study.

With the integrated development of the Internet, wireless sensor technology, cloud computing, and mobile Internet, there has been a lot of attention given to research about and applications of the Internet of Things. A Wireless Sensor Network (WSN) is one of the important information technologies in the Internet of Things; it integrates multi-technology to detect and gather information in a network environment by mutual cooperation, using a variety of methods to process and analyze data, implement awareness, and perform tests. This paper mainly researches the localization algorithm of sensor nodes in a wireless sensor network. Firstly, a multi-granularity region partition is proposed to divide the location region. In the range-based method, the RSSI (Received Signal Strength indicator, RSSI) is used to estimate distance. The optimal RSSI value is computed by the Gaussian fitting method. Furthermore, a Voronoi diagram is characterized by the use of dividing region. Rach anchor node is regarded as the center of each region; the whole position region is divided into several regions and the sub-region of neighboring nodes is combined into triangles while the unknown node is locked in the ultimate area. Secondly, the multi-granularity regional division and Lagrange multiplier method are used to calculate the final coordinates. Because nodes are influenced by many factors in the practical application, two kinds of positioning methods are designed: the unknown node is in the positioning unit or not. When the unknown node is on the side of the positioning unit, we use the method of vector similarity. Moreover, we use the centroid algorithm to calculate the ultimate coordinates of unknown node. When the unknown node is not on the side of the positioning unit, we establish a Lagrange equation containing the constraint condition to calculate the first coordinates. Furthermore, we use the Taylor expansion formula to correct the coordinates of the unknown node. In addition, this localization method has been validated by establishing the real environment.

As the adoption of renewable energy sources grows, ensuring a stable power balance across various time frames has become a central challenge for modern power systems. In line with the "dual carbon" objectives and the seamless integration of renewable energy sources, harnessing the advantages of various energy storage resources and coordinating the operation of long-term and short-term storage have become pivotal directions for future energy storage deployment. To address the complexities arising from the coupling of different time scales in optimizing energy storage capacity, this paper proposes a method for energy storage planning that accounts for power imbalance risks across multiple time scales. Initially, the Seasonal and Trend decomposition using the Loess (STL) decomposition method is utilized to temporally decouple actual operational data. Subsequently, power balance computations are performed based on the obtained data at various time scales to optimize the allocation of different types of energy storage capacities and assess the associated imbalance risks. Finally, the effectiveness of the proposed approach is validated through hourly applications using real-world data from a province in China over recent years.

The sexual reproduction of ascomycetes is controlled by the mating-type(MAT) locus. (Pseudo)homothallic reproduction has been hypothesized based on genetic data from Hirsutella sinensis (Genotype #1 of Ophiocordyceps sinensis). In this study, the differential occurrence of the mating-type genes in the MAT1-1 and MAT1-2 idiomorphs, which constitute the genetic control of O. sinensis reproduction, was analyzed in 237 strains and 5 genomes of H. sinensis. The mating-type genes were differentially transcribed in H. sinensis Strain L0106, and the MAT1-2-1 transcript in H. sinensis Strain 1229 was alternatively spliced, with an unspliced intron I containing stop codons; these findings constitute O. sinensis reproduction controls at the transcriptional and coupled transcriptional-translational levels. The occurrence of the mating-type genes and a-/α-pheromone receptor genes differed among the 5 H. sinensis genomes. The differential occurrence and transcription of these genes are inconsistent with self-fertilization under (pseudo)homothallism but suggest self-sterility of H. sinensis, which therefore needs a mating partner to achieve sexual outcrossing under heterothallism or hybridization. Consistent occurrence and transcription of the mating-type genes of both the MAT1-1 and MAT1-2 idiomorphs have been reported in natural and cultivated Cordyceps sinensis, but these findings are insufficient to determine the reproduction mode(s) because of the co-occurrence of >90 fungal species and multiple genomically independent genotypes of O. sinensis. The mutant MAT1-1-1 and α-pheromone receptor transcripts in natural C. sinensis result in the N-terminus or middle-truncated proteins, with changes in hydrophobicity and secondary structures of the proteins, suggesting heterogeneous fungal source(s) of the proteins and hybridization reproduction.

Nanocrystalline silicon oxide (nc-SiOx:H) is a multipurpose material with its varied application in solar cells as a transparent front contact, intermediate reflector, back reflector layer and even tunnel layer for passivating contacts, owing to easy tailoring of its optical properties. In this work, we systematically investigate the influence of gas mixture (SiH4, CO2, PH3 and H2), RF power and process pressure on the optical, structural and passivation properties of thin n-type nc-SiOx:H films prepared in an industrial, high throughput, plasma-enhanced chemical vapor deposition (PECVD) reactor. We provide a detailed description of the n-type nc-SiOx:H material develop-ment using various characterization techniques (SEM, EDX, Raman spectroscopy, and spectro-scopic ellipsometry) with a focus on the relationship between the material properties and the pas-sivation they provide to n-type c-Si wafers characterized by their effective carrier lifetime (τeff). Further, we also outline the parameters to be kept in mind while developing different n-type nc-SiOx:H layers for different solar cell applications. We report a tunable optical gap (1.8 – 2.3 eV) for our n-type nc-SiOx:H films as well as excellent passivation properties with τeff up to 3.5 ms (iVoc ~ 715 mV) before annealing. Oxygen content plays an important role in determining the crystallinity and hence passivation quality of the deposited nanocrystalline silicon oxide films.

The International System of Units (SI) was adopted in 1960 as a universal measuring system to be used for all areas of science. Sports Science papers have shown lots of inaccurate and inappropriate terms for quantification of athletes’ performance and the psychobiological responses to exercise (e.g., internal load). In biomechanics, external and internal loads are forces acting externally and internally, inducing stress and strain in the biological tissues. Therefore, the current review present simple proposals to correct the inappropriate terms: 1) do not use the term external load when referring to the assessment of exercise time, distance, displacement, speed, velocity, acceleration, torque, work, power, impulse, etc.; 2) do not use the term internal load when referring to the assessment of psychobiological stress markers (i.e., session rating of perceived exertion, heart rate, blood lactate, oxygen consumption, etc.); 3) do not use the term impulse when expressing other calculus than integrating force with respect to time, and neither strain, when expressing other phenomena than the body deformation. Instead, the term exercise intensity is universal and can be used to describe all forms of exercise. Finally, duration should precisely be described according to physical quantities (e.g., time, distance, displacement, speed, velocity, acceleration, force, torque, work, power, impulse, etc.) and the units accomplish by use of the SI. These simple quantifications can be performed for the exercises, sessions, microcycles, mesocycles and macrocycles of the athletes. Such standardization will provide a consistent and clear communication among sports scientists and all areas of science.

Multi-rotor drones, a kind of unmanned equipment which is widely used in military, commercial consumption and other fields, has been developed very rapidly in recent years. However, their short flight time has hindered the expansion of their application range. This can be addressed by utilizing hydrogen fuel cells, which exhibit high energy density, strong adaptability to ambient temperature, and no pollution emissions, as the power source. Accordingly, the application of hydrogen fuel cells as the power source in multi-rotor drones is a promising technology that has attracted significant research attention. This paper summarizes the development process of hydrogen fuel cell mul-ti-rotor drones and analyzes the key obstacles that need to be addressed for the further development of hydrogen fuel cell multi-rotor drones, including structural lightweight, hydrogen storage methods, energy management strategies. Additionally, prospects for the future development of hydrogen fuel cell multi-rotor drones are presented.

Motivated by empirical observations, we propose a possible extension of Gibrat's law. By applying it into the random growth theory of income distribution (Gabaix, 2009), we find that the income distribution is described by a generalized Pareto-type distribution (GPD) with three parameters. We observe that there is a parameter /elta in the GPD that plays a key role in determining the shape of income distribution. By using the Kolmogorov-Smirnov test, we empirically show that, for typical market-economy countries, /elta is close to 0 significantly, such that the income distribution is characterized by a two-class pattern in which the bottom 90% of the population is approximated by an exponential distribution and the richest 1%~3% is approximated by an asymptotic power law. However, we empirically find that, for China both in planned economy period and in early stages of market reformation (from 1978 to 1990), /elta is significantly deviated from 0, such that the bottom of the population no longer conforms to an exponential distribution.

Spinocerebellar ataxia type 3 is a neurodegenerative disease caused by an abnormal expansion of CAG repeats in the disease gene ATXN3, leading to prolonged polyglutamine (polyQ) tracts in the respective protein ataxin-3. The polyQ-expanded protein forms polyQ-containing aggregates in several brain regions which leads to neuronal cell loss. Autophagy is thought to play a significant role in clearing these polyQ-containing protein aggregates. Therefore, the autophagy mechanism was investigated in SCA3 with focus on the autophagic protein p62/sequestosome-1. Human and mouse RNA sequencing data were analyzed to determine RNA expression level of autophagic genes. Additionally, autophagy was studied in the SCA3 304Q knock-in mouse model and through several cell culture experiments using HEK-293T cells transfected with ATXN3 of differ-ent polyQ lengths. For cell culture experiments, autophagy was induced with rapamycin treat-ment, proteasomal degradation was blocked with MG132 and degradation of autophagic pro-teins was investigated using cycloheximide treatment. Here, we report an increased autophagy impairment with SCA3 disease progression seen in HEK-293T cells transfected with ATXN3 plasmid with expanded polyQ tracts, higher aged 304Q-knock-in mice, or human post-mortem brain material. Furthermore, co-localized aggregation of the autophagic protein p62 and the dis-ease protein ATXN3 was observed in the course of SCA3 disease. Therefore, we suggest a signifi-cant role for p62 in aggregate formation seen in the neurodegenerative disease SCA3.

Existing research indicates that mineralization of Carlin-type gold deposit is related to geological structures, but current studies mostly focus on the qualitative association, and lack quantitative analysis of the relationship between mineralization and structural features, which limits the potential for predictive mineral exploration. In this study, the Nibao Carlin-type gold deposit was selected as the research area to conduct three-dimensional geological modeling, spatial analysis, and three-dimensional prospectivity modeling. Spatial analysis revealed that the majority of gold ore bodies are situated near the main fault, with gold mineralization primarily occurring within a spatial range of approximately -80 meters to 20 meters from the main fault plane. This spatial distribution predominantly aligns in a SW-NE direction. Spatial characteristic extraction of fault slope indicators suggests that the slope angles are conducive to the migration and accumulation of ore-forming hydrothermal fluids, with ore body metal content rapidly increasing within an angle range of approximately 20° to 60°. The shape analysis of the mainfault indicates that the principal spaces of mineralization enrichment are within -10m to 20m of the fault plane undulations, where gold resources are concentrated in a relatively flat area. However, the degree of mineralization is more pronounced in the protruding sections than in the depressed areas. The areas with significant dip changes in faults display higher variations in orebody attitudes, with mineralization noticeably weaker in areas where the fault steepness changes markedly. Ore-bearing units exhibit significantly higher grades within the -17° to 3° interval of fault steepness transition. This interval also sees a rapid accumulation of gold resources. The Nibao gold mine's mineralization is derived from deep, ore-bearing hydrothermal fluids ascending along major fractures, precipitating, and accumulating in favorable ore-hosting spaces (faults, anticline cores) and lithological combinations (sedimentary tuffs, tuffs). Three deep potential gold targets were identified, highlighting the deep western edge of the F1 fault and the deep southeast-trending lower plate as prospective areas for future exploration. This study underscores the effectiveness of 3D prospective modeling as an indispensable tool for elucidating the spatial distribution of fault-controlled Carlin-type gold deposits and their tectonic determinants.

In this paper, we have established Hermite-Hadamard inequalities for r-preinvex functions via fractional integrals.

The influence of short term water absorption on the mechanical properties of halloysite nanotubes-multi layer graphene reinforced polyester hybrid nanocomposites has been investigated. The addition of nano-fillers significantly increased the flexural strength; tensile strength and impact strength in dry and wet conditions. After short term water exposure; the maximum microhardness; tensile; flexural and impact toughness values were observed at 0.1 wt% MLG. The microhardness increased up to 50.3%; tensile strength increased up to 40% and flexural strength increased up to 44%. Compared to dry samples; the fracture toughness and surface roughness of all types of produced nanocomposites were increased that may be attributed to plasticization effect. Scanning electron microscopy revealed that the main failure mechanism is caused by the weakening of nano-filler-matrix interface induced by water absorption. It was further observed that synergistic effects were not effective at concentration of 0.1 wt% to produce considerable improvement in mechanical properties of produced hybrid nanocomposites.

Background and Objectives Neurofibromatosis 1 (NF1 MIM # 162200), also known as von Recklinghausen disease, is among the most common autosomal dominantly transmitted disorders characterized mainly by neurocutaneous manifestations such as café au lait spots, intertriginous freckling, various types of neurofibromas (cutaneous neurofibromas or plexiform tumors), neurological manifestations, and bone abnormalities. It occurs with an incidence of 1:3000–1:4000 cases. Cone-rod dystrophies belong to the large group of retinal dystrophies, a highly heterogeneous group of disorders clinically manifested mainly by damage to cone and rod cells and have a broad spectrum of clinical manifestations. Many genes are involved in their etiology, with more than 100 currently identified, including the CRX gene responsible for the autosomal dominant form of cone-rod dystrophy (ad CORD). Materials and Methods: The authors present an intriguing case of a patient diagnosed with Neurofibromatosis type 1 (NF1) as an infant and ocular involvement (myopia and astigmatism onset at age 15), which yielded a surprising molecular testing result. Results: Molecular DNA analysis identified a rare occurrence of two mutational variants, including a pathogenic variant in the NF1 gene, c.3871-2A, and a likely pathogenic variant in the CRX gene c.119G>A. Conclusions: The authors present this case to highlight the surprises offered by molecular testing in a condition where the diagnosis is usually based on clinical criteria, thus providing patients with competent genetic advice.

In this paper, we establish the generalized Qi-type inequality involving conformable fractional integrals. The results presented here would provide extensions of those given in earlier works.

With the rising cost of animal feed protein, finding affordable and effective substitutes is crucial. Walnut kernel cake, a polyphenols, fiber, protein and fat-rich byproduct of walnut oil extraction, has been underexplored as a potential protein replacement in pig feed. In this study, we found that feeding large Diqing Tibetan pigs walnut kernel cake promoted adipose deposition and improved pork quality during pig growth. Transcriptome analysis revealed the upregulation of genes ANGPTL8, CCNP, ETV4, and TRIB3, associated with adipose deposition. Pathway analysis highlighted enrichment in adipose-deposition-related pathways, including PPAR, Insulin, PI3K-Akt, Wnt, and MAPK signaling. Further analysis identified DEGs (differentially expressed genes) positively correlated with adipose-related traits, such as PER2 and PTGES. Single-cell transcriptome data pointed to the specific expression of CD248 and PTGES in adipocyte progenitor/stem cells (APSCs), pivotal for adipocyte differentiation and adipose deposition regulation. This study demonstrates walnut kernel cake's potential to substitute soybean cake in pig feed, providing high-quality protein and promoting adipose deposition. It offers insights into feed protein replacement, human functional food, fat metabolism, and related diseases, with marker genes and pathways supporting pig breeding and pork quality improvement.

This paper presents performed Ansys numerical simulation on WindFloat structures. It contributes to the methodology of calculation based on CFD instruments to study the movements of the waves on semi-submersible stationary structures and highlights the importance of using RAO functions. RAO numerical approach developed can be applied to design semisubmersible WindFloat structures in order to fulfill essential requirements regarding operational safety and design. Numerical methodology was designed in accordance marine loads and the I.T.T.C. recommendations. The numerical RAO results for regular wave movements include many elements for the semi-submergible structure. Close results to open sea operation can be achieved by constant improvement in numerical simulation methodologies. The work opens the way for further hydrodynamic development on irregular waves for realistic hydrodynamic and structural response of the actual semi-submersibles at sea. The results demonstrate the accuracy of RAO function approach for specific WindFloat in Jonswap spectrum.

Renewable Energy Communities (RECs) are emerging as an effective concept and model to empower the active participation of citizens on the energy transition, not only as energy consumers, but also as promoters of environmentally friendly energy generation solutions. This paper aims to contribute to the management and optimization of individual and community Distributed Energy Resources (DER). The solution follows a price and source-based REC management program, in which consumers day-ahead flexible loads (Flex Offers) are shifted according to electricity generation availability, prices and personal preferences, to balance the grid and incentivize user participation. The heuristic approach used in the proposed algorithms allows the optimization of energy resources in a distributed edge and fog approach with a low computational overhead. The simulations performed using real world energy consumption and flexibility data of a REC with 50 dwellings show an average cost reduction of 10.6% and an average increase of 11.4% in individual self-consumption. Additionally, the case-study demonstrates promising results regarding grid load balancing and the introduction of intra-community energy trading.

Researchers achieved high torque volume ratios in magnetorheological (MR) fluid braking devices by introducing multiple layers and multiple poles concepts. The number of magnetic poles, pole geometry and placement have a significant effect on these multi-pole MR brake performances. This research work focused on the effect of the pole head geometry in a multi-pole dual-disc MR brake for the enhancement of braking torque. The magnetic field generated by the electromagnetic coil has to penetrate through pole heads and travel orthogonally through the rotor and MR fluid layers to achieve maximum brake torque. This flow depends on the profiles of the magnetic pole head area and corresponding core dimensions. This study considered pentagon, square, hexagon, trapezoid and ellipse pole head profiles in place of the conventional circular pole and the best possible core dimensions were used for each geometry. A three-dimensional electromagnetic analysis of the MR brake is conducted to simulate the brake performance. Results showed that the hexagonal and elliptical pole heads are having better magnetic field area, magnetic intensity distribution and higher magnetic flux lines piercing through the MR fluid perpendicularly than the circular and square pole heads. An increment of 3.88% for braking torque performance is obtained, and the braking torque is significantly enhanced.

Recent years have witnessed significant advances in reinforcement learning (RL), which has registered remarkable success in solving various sequential decision-making problems in machine learning. Most of the successful RL applications, e.g., the games of Go and Poker, robotics, and autonomous driving, involve the participation of more than one single agent, which naturally fall into the realm of multi-agent RL (MARL), a domain with a relatively long history, and has recently re-emerged due to advances in single-agent RL techniques. Although, typically, the communication protocol between agents is manually specified and not altered during training, recently, some papers have shown signs of trying to emerge a communication between agents on the one hand and, on the other hand, to understand what is exchanged between agents. So, there is a growing body of literature on this topic which includes qualitative and quantitative studies and the ones that apply mixed methods. This study presents the scoping review of the methodological strategies undertaken in a total of 16 research articles. The results present the critical appraisal of quantitative methods in terms of validity and reliability and for qualitative methods considering four trustworthiness factors. In the end, relevant insights are further explored with implications and reflections on how they can benefit one's research in the field.

Underwater visual detection technology plays a pivotal role in fields such as marine exploration. With the increasing demand for underwater monitoring, the quest for efficient and reliable methods for underwater target recognition has become particularly significant. To address this requirement, this study developed an innovative underwater object detection architecture based on YOLOv8, named YOLOv8-MU, aimed at significantly enhancing detection accuracy.By integrating the LarK module proposed in UniRepLKNet to optimize the backbone network, YOLOv8-MU aims to achieve a larger receptive field without increasing the model’s depth. Further, this research introduces C2fSTR, an innovative method that combines Swin Transformer with the C2f module. Additionally, we have incorporated the SPPFCSPC_EMA module, which combines Cross-Stage Partial Fast Spatial Pyramid Pooling (SPPFCSPC) with attention mechanisms, significantly improving the detection accuracy and robustness of various biological targets. Moreover, by introducing a fusion block based on DAMO-YOLO into the neck of the model, we further enhanced the model’s capability in multi-scale feature extraction. Finally, the adoption of the MPDIoU loss function, designed around vertex distance, effectively tackles the challenges of localization accuracy and boundary clarity in underwater organism detection. Experimental results on the URPC2019 dataset demonstrate that the YOLOv8-MU model achieved an [email protected] of 78.4%, marking improvements of 5.6%, 1.1%, and 4.0% over YOLOv5s, YOLOv7, and YOLOv8n respectively, indicating the leading performance (SOTA) of this method. On the other hand, further evaluation on the URPC2020 dataset confirmed the generalization capability of the YOLOv8-MU architecture, with its [email protected] reaching 80.4%, surpassing various models including YOLOv5x and YOLOv8n, showcasing the wide applicability of our proposed improved model architecture.

The tribology behavior, tribofilm formation and structure evolution of polytetrafluoroethylene (PTFE) filled with α-Al2O3 and SiO2 nanoparticles during sliding against steel counterparts under different loads were studied. It is found that both composites exhibit good wear resistance across the pressure of 1 MPa to 10 MPa, with the α-Al2O3/PTFE composite demonstrates better performance stability compared to the SiO2/PTFE composite. The high wear resistance is attributed to the formation of tribofilms at the friction interface. For the α-Al2O3/PTFE, an island-like tribofilm is formed with a thickness ranging from 100 to 200 nm, while the tribofilm of the SiO2/PTFE composite is thinner, measuring approximately 50 to 100 nm, and manifest a striped pattern. The chemical composition, both at the surface and subsurface levels, as well as the morphology of the tribofilms were studied using FTIR spectrometry, X-Ray photoelectron spectroscopy (XPS), and FIB-TEM. It is found that the difference in thickness and microstructure of the tribofilms for the two composites is mainly due to the tribochemistry of the nanoparticles. The α-Al2O3 nanoparticle plays a "cohesion" role during the formation of the tribofilm, which facilitates the formation of a thicker, more uniform, and stronger adhered tribofilm on the metallic counterpart, making it more robust against higher shear stress.

The glucose-insulin regulatory system and its glucose oscillations is a recurring theme in the literature because of its impact on human lives, mostly the ones affected by diabetes mellitus. Several approaches were proposed, from mathematical to data-based models, with the aim of modeling the glucose oscillation curve. Having such a curve, it is possible to predict, when injecting insulin in type 1 diabetes (T1D) individuals. However, the literature presents prediction horizons no longer than 6 hours, which could be a problem considering their sleeping time. This work presents Tesseratus, a model that adopts a multi-agent approach to combine machine learning and mathematical modeling to predict the glucose oscillation up to 8 hours. Tesseratus uses the pharmacokinetics of insulins and data collected from T1D individuals. Its outcome can support endocrinologists while prescripting daily treatment for T1D individuals, and provide personalized recommendations for such individuals, to keep their glucose concentration in the ideal range. Tesseratus brings pioneering results for prediction horizons of 8 hours for nighttime, in an experiment with seven real T1D individuals. It is our claim that Tesseratus will be a reference for classification of glucose prediction model, supporting the mitigation of short- and long-term complications in the T1D individuals.

Assessment of extreme events and climate change on reservoir inflow is important for water and power stressed countries. Projected climate is subject to uncertainties related to climate change scenarios and Global Circulation Models (GCMs’). Extreme climatic events will increase with the rise in temperature as mentioned in the AR5 of the IPCC. This paper discusses the consequences of climate change that include extreme events on discharge. Historical climatic and gauging data were collected from different stations within a watershed. The observed flow data was used for calibration and validation of SWAT model. Downscaling was performed on future GCMs’ temperature and precipitation data, and plausible extreme events were generated. Corrected climatic data was applied to project the influence of climate change. Results showed a large uncertainty in discharge using different GCMs’ and different emissions scenarios. The annual tendency of the GCMs’ is bi-vocal: six GCMs’ projected a rise in annual flow, while one GCM projected a decrease in flow. The change in average seasonal flow is more as compared to annual variations. Changes in winter and spring discharge are mostly positive, even with the decrease in precipitation. The changes in flows are generally negative for summer and autumn due to early snowmelt from an increase in temperature. The change in average seasonal flows under RCPs’ 4.5 and 8.5 are projected to vary from -29.1 to 130.7% and -49.4 to 171%, respectively. In the medium range (RCP 4.5) impact scenario, the uncertainty range of average runoff is relatively low. While in the high range (RCP 8.5) impact scenario, this range is significantly larger. RCP 8.5 covered a wide range of uncertainties, while RCP 4.5 covered a short range of possibilities. These outcomes suggest that it is important to consider the influence of climate change on water resources to frame appropriate guidelines for planning and management.

Thermostatically controlled loads have great potential to make a significant contribution to improving energy efficiency in the building sector, which is responsible for 40% of greenhouse gas emissions in the EU. This, in addition to the environmental damage, represents a huge expense in the electricity bill. Therefore, it is very important to train engineers on how to design energy management systems for TCLs. With this goal in mind, it would be very useful to have a simulation-based educational tool (SBET) to understand thermostatically controlled loads, their characteristics and possibilities in energy efficiency. In addition, it would be very useful if this tool could be introduced in engineering curricula to help students to be better trained and enter the labor market with more opportunities. Based on the shortcomings detected, this work develops a SBET specifically designed to teach about TCLs (SBET-TCLs), both about their intrinsic characteristics and their better management. To verify the developed SBET-TCL, it has been tested in a real scenario: A survey was carried out among the students of the subject 'Alternative Energy Sources' of the degrees of Industrial Engineering. The results show that the use of SBET-TCL has very positive effects on the learning process.

Background: Runners have high incidence of repetitive load injuries, and habitual runners often use smartwatches with embedded IMU sensors to track their performance and training. If accelerometer information from such IMUs can provide information about individual tissue loads, then running watches may be used to prevent injuries. Methods: We investigate a combined physics-based simulation and data-based method. 285 running trials from 76 real runners are subjected to physics-based simulation to recover forces in the Achilles tendon and patella ligament, and the collected data are used to train and test a data-based model using elastic net and gradient boosting methods. Results: Correlations up to 0.95 and 0.71 for the patella ligament and Achilles tendon forces, respectively, are obtained, but no single best predictive algorithm can be identified. Conclusions: Prediction of tissues loads based on body-mounted IMUs appears promising but requires further investigation before deployment as a general option for users of running watches to reduce running-related injuries.

Renovation, restoration, remodeling, refurbishment, and retrofitting of build-ings often imply modifying the behavior of the structural system. Modification sometimes includes applying forces (i.e., concentrated loads) to beams that before were subjected to distributed loads only. For a reinforced concrete structure, the new condition causes a beam to bear a concentrated load with the crack pattern that was produced by the distributed loads that acted in the past. If the concentrated load is applied at or near the beam’s midspan, the new shear demand reaches the maximum around the midspan. But around the midspan, the cracks are vertical or quasi-vertical, and no inclined bar is present. So, the actual shear capacity around the midspan not only is low, but also can be substantially lower than the new demand. In order to bring the beam capacity up to the demand, fiber-reinforced-polymer composites can be used. This paper presents a design method to increase the concentrated load-carrying capacity of reinforced concrete beams whose load distribution has to be changed from distributed to concentrated, and an analytical model to pre-dict the concentrated load-carrying capacity of a beam in the strengthened state.

The cyclic load applied to civil and mining structures can lead to a reduction of the materials’ strength, different from that which would occur with a monotonous load. Numerous cases can be found where the decay of the rock parameters subjected to this type of stress leads to progressive or sudden collapse: among them, tunnel walls, pillars and slabs in mining operations, roads with a heavy vehicle transit, abutments of bridges and dams can be quoted. The topic can therefore be fundamental for a correct structural design, to avoid problems during the life of the structure. However, given the heterogeneity of the rock materials and the difficulty of their characterization under this aspect, an unequivocal analysis is hardly achievable. Then, the discussion initially develops through a general historical review of the concept of fatigue, with a synthetic collection of case histories. The laboratory tests on rock samples are then examined and the most important results obtained are discussed. Finally, a comparison between different types of tests is proposed. The experimental data are expressed through the Wӧhler diagram. The goal is to fill the lack of design codes or standards in the field of cyclic stresses applied to rock materials, the understanding of its effect being of great interest in order to apply suitable parameters in the design phase.

To assess the community health workers’ (CHWs) knowledge, attitude, and practices (KAP) in type-2 diabetes (T2D) and hypertension (HTN) management. We thus also sought to assess the potential health system barriers for incorporating CHWs in T2D and HTN management. Mixed-method study comprised (1) a survey among 153 active CHWs to assess their KAP of T2D and HTN, and (2) semi-structured interviews with key informants to understand challenges of the health system and proposed solutions in incorporating CHWs in T2D and HTN management. The majority of CHWs correctly answered general knowledge questions on NCDs, risk factors, and prevention; however, only one-quarter correctly answered questions on smoking, family history, or tobacco use as risk factors. Most respondents appeared to have positive attitudes and have been practicing some activities related to T2D and HTN. Both financial and non-financial resource constraints were cited as challenges of the health system; therefore, re-structuring the role definition of CHWs and task of responsibilities, and assessment the need and workload have been proposed as ways forwards to effectively incorporate CHWs in T2D and HTN care. CHWs in Cambodia have shown their potential in T2D and HTN management; however, a well-designed strategy including technical training, clearly defined roles and responsibilities, and strong supporting structure are important to maximize their potential in the health system.

The speed-density or flow-density relationship is a fundamental aspect of traffic flow theory. Single-regime models often face challenges in consistently fitting empirical data under diverse traffic conditions. This paper addresses the inaccuracies of single-regime models, attributing them not only to their functional forms but also to data dispersion and sample selection bias. To mitigate these issues, the data is segmented into day and night periods, leading to the creation of separate models for each. Calibration results, conducted on data from two freeways, Tehran-Karaj and Tehran-Qom, reveal distinct challenges, with the former exhibiting high dispersion and the latter showing low dispersion. Surprisingly, single-regime models demonstrate notable effectiveness when applied to distinct day and night data. Further analysis, categorizing data into day and night, results in reduced errors (20-60% improvement in R-Square), emphasizing the potential for enhanced accuracy by considering distinct regimes. Overall, the study underscores the significance of regime-specific considerations for accurate traffic flow modeling. Upon thorough evaluation, the study highlights the superiority of the neural network Multi-layer Perceptron (MLP) over traditional models. The research discusses the implications of incorporating day and night parameters into the models, emphasizing their potential for accuracy enhancement.

This paper presents an innovative multi-agent, data-driven reinforcement learning (RL) approach to develop and utilize the thermal equivalent network model that represents the motor's thermal dynamics. A multi-agent reinforcement learning is designed and trained to adjust the model parameters using data from several motor driving cycles. To ensure the incoming driving cycle matches the historical data before employing the pre-trained RL agents, offline statistical analysis and clustering techniques are developed and used. Numerical simulations highlighted the RL agent's ability to develop strategies that effectively address the variability of driving cycles. The proposed RL framework showed its capability to accurately reflect the motor's thermal behavior under various driving conditions.

Keywords: pelvic ultrasound, follicle number per ovary, FNPO, ovarian volume, PCOM, upper normal limits, referral population

The three-pronged sliding universal coupling is a new kind of three-pronged coupling. To study its kinematic and dynamic characteristics, directional cosine matrices are utilized as tools to analyze the coordinate systems by establishing simplified geometric models and corresponding motions. Through the analysis of the motions of the input and output shafts and employing the method of single-force element, a set of equilibrium equations for the forces acting on the output shaft and the input shaft are formulated for solution analysis. The research indicates that during the rotation process, there exists a small angular difference between the input shaft and the intermediate shaft, demonstrating the quasi-constant angular velocity characteristics of the new tripod sliding universal coupling. The curves of the forces and torques acting on each component of the coupling approximate sinusoidal curves. The optimal operating angle range for the new tripod universal coupling is at angle , during which the system exhibits good transmission and mechanical performance.

Protein tyrosine phosphatase receptor type E (PTPRE) is a member of the “classical” protein tyrosine phosphatase subfamily and regulates a variety of cellular processes in a tissue-specific manner by antagonizing the function of protein tyrosine kinases. PTPRE plays a tumorigenic role in different human cancer cells, but its role in retinoblastoma (RB), the most common malignant eye cancer in children, remains to be elucidated. Etoposide resistant RB cell lines and RB patients display significant higher PTPRE expression levels compared to chemosensitive counterparts and the healthy human retina, respectively. PTPRE promotor methylation analyses revealed that PTPRE expression in RB is not regulated via this mechanism. Lentiviral PTPRE knockdown (KD) induced a significant decrease in growth kinetics, cell viability, and anchorage independent growth of etoposide resistant Y79 and WERI RB cells. Caspase-dependent apoptosis rates were significantly increased and a re-sensitization for etoposide could be observed after PTPRE depletion. In vivo chicken chorioallantoic membrane (CAM) assays revealed decreased tumor formation capacity as well as reduced tumor size and weight following PTPRE KD. Expression levels of miR631 were significantly downregulated in etoposide resistant RB cells and patients. Transient miR631 overexpression resulted in significantly decreased PTPRE levels and concomitantly decreased proliferation and increased apoptosis levels in etoposide resistant RB cells, impacts mirroring PTPRE KD effects and indicating PTPRE regulation via this miR. Additionally, PTPRE KD led to altered phosphorylation of protein kinase SGK3 and - dependent on the cell line - also AKT and ERK1/2, suggesting potential PTPRE downstream signaling pathways. In summary, these results indicate an oncogenic role of PTPRE in chemoresistant retinoblastoma.

In this paper, a new approach to retrieve semantic images based on shape and geometric features of image in conjunction with multi-class support vector machine is proposed. Zernike moment as shape feature is to verify the invariance of objects for silhouette image. In addition, a set of geometrical features is to explore the objects shape using two features of rectangularity and circularity. Then the extracted features are normalized and employed for multi-class support vector machine either for learning or retrieving processes. The retrieving process relies on three main tasks which namely Query Engine, Matching Module and Ontology Manger, respectively. Query Engine is to build the input text or image query using SPARQL language. The matching module extracts the shape and geometric features of image’s objects and employ them to Ontology Manger which in turn inserts them in ontology knowledge base. Benchmark mammals have been conducted to empirically conclude the outcome of proposed approach. Our experiment on text and image retrieval yields efficient results to problematic phenomena than previously reported.

In the increasingly complex environment of downhole working conditions such as frequent opening and closing of oil and gas wells, acidification/multi-stage fracturing, steam huff and puff, and strong injection and production, the traditional casing string design method standards based on strength design have gradually highlighted their limitations. It is necessary to formulate string design method standards that consider the full life cycle of wells such as drilling and completion, fracturing, and production operations. Starting from the analysis of the advantages and disadvantages of traditional casing string design methods, this paper presents the characteristics of the strain design methods and seal design methods that have been formulated for the life cycle of the string. The strain design method breaks through the traditional design concept and allows the design concept of controllable deformation of the pipe string. The sealing design method is currently the only standard method for the design of tubing strings. At the same time, it further proposes to consider the trend of pipe strength deterioration and establish a time dimension-based life cycle pipe string design method standard, which effectively solves the safety problem of pipe string design in production and operation.

Probiotic feed additives have attracted considerable research interest in recent years because the effectiveness of probiotics can differ across microbial strains and the supplemented macroorganisms. The present study was conducted on 16 lambs divided into two groups (C - control and E - experimental). The examined lambs were aged 11 days at the beginning of the experiment and 40 days at the end of the experiment. The diet of group E lambs was supplemented with a multi-strain probiotic formulation (Lactobacillus plantarum AMT14, Lactobacillus plantarum AMT4, Lactobacillus rhamnosus AMT15, and Bifidobacterium animalis AMT30), whereas group C lambs did not receive the probiotic additive. At the beginning of the experiment (day 0) and on experimental days 15 and 30, blood was sampled from the jugular vein to determine and compare: phagocytic activity (PHAGOTEST) and oxidative metabolism (PHAGOBURST) of peripheral blood granulocytes and monocytes by flow cytometry. An analysis of the phagocytic activity of granulocytes and monocytes revealed significantly higher levels of phagocytic activity (expressed as the percentage of phagocytic cells and mean fluorescence intensity) in lambs administered the multi-strain probiotic formulation than in the control group. The probiotic feed additive also exerted a positive effect on the oxidative metabolism of both granulocytes and monocytes (expressed as the percentage of oxidative metabolism and mean fluorescence intensity) after stimulation with Escherichia coli bacteria and with PMA (4-phorbol-12-β-myristate-13-acetate).

Background and Objectives: In this current state, Type 2 Diabetes Mellitus (T2DM) is more prevalent in the population, and metformin is used as a first-line medication for treating it. There was up surge in the utilization of alternative therapies in the management of diabetes. Especially in diabetes, Herbal medicines are considered safe and reliable by majority of the population. Aim: The purpose of this research is aimed to estimate the safety and efficacy of Polyherbal Metabolite Compounds (PHMC) capsules in adults with T2DM. Materials and Methods: In this study, 60 T2DM patients aged 18-60 years were randomly assigned to Groups A (30) receiving Metformin 500 mg twice a day after food and Group B (30) receiving PHMC capsule 500 mg twice a day after food in a prospective, randomized and open-label clinical study. The in-silico simulation study was performed to selected plants major compounds on target protein Insulin-like Growth Factor-1 (1K3A). Result: The PHMC is found to be safe and effective in the management of T2DM. The FBS, PPBS and HbA1c were significantly lowered (p

One of the most important problems of geotechnical engineering is the design of pile foundations. Piles are generally designed for vertical and horizontal static loads. However, it is important to design piles against dynamic loads in regions with high seismicity. This study verified a centrifuge experiment obtained from the literature with a finite element program. With the kinematic interaction analyses made for this purpose, the effect of parameters such as layered soil, groundwater, pile stiffness, and earthquake acceleration were investigated numerically. According to the results obtained, it was understood that the earthquake magnitude is the most important parameter in kinematic interaction analyses. In addition, in layered soil conditions, the fact that 75% of the pile length is in the weak soil creates the most unfavorable situation. It has been observed that pile stiffness and groundwater level also have certain effects on the kinematic interaction.

Background: The question of whether children are less likely to pass on SARS-CoV-2 is important for planning society’s response to the pandemic. A document available on the Charité hospital website has not been formally published but is frequently referred to as supporting the notion that viral loads are similar in children and adults. Methods: The summary data from this document was extracted and used to produce summary statistics for three age groups: younger children (ages up to 11), older children (ages 12 to 19) and adults (ages 20 and above). Viral loads between the two children’s groups and the adult group were compared using Welch’s t test, which only requires group means and standard deviations and which is robust against moderate departures from normality. Findings: Viral loads were significantly lower than in adults for both younger children (p=0.04) and older children (p=0.04). Overall, viral loads were lower in children than adults (p=0.005). Interpretation: For both younger and older children, on average those with detectable SARS-CoV-2 have significantly lower viral loads than adults. Funding: No funding was received for this analysis.

Background and Objectives: Cancer as the second leading cause of death in the United States poses a huge healthcare burden. Barriers to access to advanced therapies influence the outcome of cancer treatment. In this study, we examined whether insurance types affect the quality of cancer clinical care regarding access to an important monoclonal antibody, ramucirumab. Materials and Methods: Data for 13,340 cancer patients with Purchased or Medicaid insurance from the All of Us Database were collected for this study. The Chi-square test of proportions was employed to determine the significance of patient cohort characteristics and ramucirumab usage between Purchased and Medicaid insurance groups. The independent t-test was utilized to assess the influences of other determinants on insurance types. Results: Cancer patients who are African American, with lower socioeconomic status, or with lower educational attainment are more likely to be insured by Medicaid. Analysis of survey questions demonstrated the relationship between income and education level with insurance type as Medicaid cancer patients were less likely to receive primary care and specialist physician access and more likely to request lower cost medications. In addition, those with Medicaid insurance were identified to have poorer access to expensive therapeutics like ramucirumab compared to those with Purchased insurance.  Conclusions: The inequities of the US healthcare system are observed for cancer patient care; access to physicians and therapeutics are highly varied and dependent on insurance types. Socioeconomic status determines insurance type, which unfortunately generates a significant impact on cancer treatment and disease outcome.

The essence of cross-modal generation and retrieval modeling for image-text interactions lies in semantic consistency. Among these, cross-modal representation alignment serves as the foundational requirement for achieving cross-modal semantic consistency. The crux of our proposed method entails the collaborative training of an image captioning model(referred to as the ’captioner’) and a pair of contrastive encoders for image-text matching(referred to as the ’concoder’). This synergistic approach yields concurrent enhancements in concoder’s performance, captioner’s proficiency, and cross-modal semantic coherence. We coin the proposed method as ‘ReCap’. To begin, we initialize the concoder through knowledge distillation from a pre-trained model. During the training process, we use the output of the initialized concoder as input to a residual attention network, jointly training it with the captioner to achieve semantic consistency. Subsequently, we iteratively update the concoder during the image-text momentum encoding phase using the residual attention network, creating a closed-loop for semantic consistency resolution. Upon completion of training, the concoder and captioner modules can be used independently to perform tasks related to cross-modal retrieval and cross-modal generation of text and images. In order to substantiate the efficacy of our proposed method, we initially conducted empirical experiments encompassing image-text retrieval and image captioning tasks, employing a widely recognized benchmark dataset, MSCOCO. Subsequently, we assessed the fine-grained cross-modal alignment performance of the concoder through an image classification task on the iNaturalist 2018 dataset. The achieved performance metrics notably surpassed those achieved by several incumbent state-of-the-art models, thus validating the proficiency of our method. Finally, motivated by the practical requirements of handling the nature conservation image data, we performed caption annotation for the iNaturalist 2018 dataset. Subsequently, we trained the ReCap on this annotated data. Experimental results demonstrate that our proposed method can maintain semantic consistency between cross-modal retrieval and image caption generation for species with similar visual features but distinct semantics. This achievement signifies a meaningful exploration in the field of cross-modal semantic consistency representation, holding significant practical value in the domain of biological research.

Biochar is a carbonaceous material derived from the thermochemical conversion of biomass under oxygen-lean conditions. Its properties render it many applications in agriculture, environmental remediation, and catalysis. Commonly produced by pyrolysis under a nitrogen atmosphere, the biochar composition is influenced mainly by residence time, heating rate, and process temperature. The existing literature primarily assesses biochar properties, such as ultimate, proximate, calorific, porosity, and combustibility, generated under various thermo-conversion conditions. However, there is a notable lack of sufficient investigation and attention given to the practical application of biochar. This article seeks to bridge that gap by enhancing the comprehension of the necessary experimental assessment for specific biochar applications and proposing process optimization methods using Multi-Criteria Decision Analysis (MCDA). By delving into these aspects, the study offers a concise overview of biochar production and presents a comprehensive panorama based on articles and patents. Additionally, the research explores the physicochemical characterization techniques associated with biochar and its various applications in conjunction with MCDA. This comprehensive approach aims to uncover valuable insights that could further advance the practical and sustainable utilization of biochar in a wide range of fields.

Introduction: maxillary hypoplasia and mandibular asymmetry may be corrected with orthognathic surgery at the completion of growth. Many patients require segmental Le Fort I osteotomies to obtain the most stable results. Unfortunately, if Invisalign is chosen for pre-surgical preparation, ClinCheck © software does not allow for prediction when these complex surgeries are planned. The objective of this paper was to show the potential of aligners beyond its software in most complex cases like multiple-piece maxillary osteotomies in cleft and non-cleft patients. Method: Thirteen patients who underwent pre-surgical treatment with clear aligners-Invisalign (study group) were matched in terms of diagnosis, surgical procedure, and orthodontic complexity with thirteen patients treated using fixed appliances (control group). A technique based on simple superimposition was devised to enhance the software for creating a suitable occlusion for segmental pre-surgical treatments. Virtual curves following the lower arch were employed to guide the correct pre-surgical positions of the upper teeth. The amount of impressions required in both groups to achieve satisfactory pre-surgical alignment of the segmented arches was compared. Results: one or no refinement phase were needed in the Invisalign group to reach an acceptable pre-surgical occlusion while the amount of pre-surgical impressions taken in order to reach adequate coordination with fixed appliance treatment was slightly higher. The average overall treatment duration did not show a statistically significant variation between the groups. Conclusions: it appears that clear aligner could serve as an effective treatment for individuals with skeletal discrepancies, including cleft and craniofacial anomalies, necessitating segmental Le Fort I osteotomies when aided by the suggested superimposition approach during digital pre-surgical movement simulations. More sophisticated softwares will certainly be implemented in the future.

The Circular Bioeconomy (CBE) combines the concepts of bioeconomy and circular economy. As an alternative concept to the current fossil-based, linear economy, it de-scribes an economy based on the efficient valorization of biomass. It is regional in nature and aims to improve sustainability. An analysis of the transition process, by identifying its success criteria and assessing its impacts through the modelling of technology-specific scenarios is necessary to ensure that CBE concepts are sustainable. However, a compre-hensive consideration of regional influences on both is lacking. Based on extensive literature research and an expert survey, we (i) present a compre-hensive catalog of CBE success criteria and discuss their region-specific character and (ii) develop a methodology based on evaluation matrices that enable to match CBE technolo-gies with regions. The matrices support the evaluation of technological and regional characteristics influencing the successful CBE implementation. The results show that the success criteria "biomass resources", "technological", and "social" are perceived as highly important, and that most of the success criteria are both region- and technology-specific, highlighting the relevance of developing matrices to match them. We describe such matrices indicatively for the two broadest and most im-portant success criteria clusters “social acceptance” and “biomass supply chain”. With this, we substantiate the regional nature of CBE and raise the awareness on the importance of considering regional conditions in CBE transition processes. Furthermore, we provide practical guidance on how regional conditions can be reflected in the selection of technologies, e.g. in regional CBE technology scenarios.

Recycling waste products is an environmental-friendly activity that can bring benefits to accompany, saving manufacturing costs and improving economic efficiency. For the beer industry, recycling bottles can reduce manufacturing costs and reduce the industry's carbon footprint. This paper presents a model for a multi-objective collection-distribution center location and allocation problem in a closed loop supply chain for the beer industry, in which the objective is to minimize total costs and transportation pollution. Uncertainties in the form of randomness and fuzziness are jointly handled in this paper to ensure a more practical problem solution, for which returned bottle sand unusable bottles are considered fuzzy random variables. A heuristic algorithm based on priority-based global-local-neighbor particle swarm optimization (pb-glnPSO) is applied to ensure reliable solutions for this NP-hard problem. A case study on a beer operation company is conducted to illustrate the application of the proposed model and demonstrate the priority-based global-local-neighbor particle swarm optimization.

Performance of the overhead squat may affect golf swing mechanics associated with golf-related low back pain. This study investigates the difference in lumbar kinematics and joint loads during the golf downswing between golfers with different overhead squat abilities. Based on the per-formance of the overhead squat test, 21 golfers aged 18 to 30 years were divided into the highest-scoring group (HS, N=10, 1.61 ± 0.05 cm, and 68.06 ± 13.67 kg) and lowest-scoring group (LS, N=11, 1.68 ± 0.10 cm, and 75.00 ± 14.37 kg). Data collection used a motion analysis system, two force plates, and TrackMan. OpenSim software was used to simulate the joint loads for each lum-bar joint. An independent t-test was used for statistical analysis. Compared to golfers demonstrat-ing limitations in the overhead squat test, golfers with better performance in the overhead squat test demonstrated significantly greater angular extension displacement on the sagittal plane, smaller lumbar extension angular velocity, and smaller L4-S1 joint shear force. Consequently, the overhead squat test is found to be a useful index to reflect lumbar kinematics and joint loading patterns during the downswing, and provides a good training guide reference for reducing the risk of a golf-related low back injury

Contamination in coastal regions attributed to fluoride and nitrate cannot be disregarded, given the substantial environmental and public health issues they present worldwide. Maintaining water quality is crucial for environmental well-being. This comprehensive study was performed to assess the spatial as well as indexical water quality, identify contamination sources, and evaluate associated health risks pertaining to nitrate and flouride in AlHassa region, KSA. The physiochemical results revealed a pervasive pollution of the overall groundwater. The dominant water type was Na-Cl, indicating saltwater intrusion and reverse ion exchange impact. Spatiotemporal variations in physicochemical properties suggest diverse hydrochemical mechanisms, with geogenic factors primarily influencing groundwater chemistry. The groundwater pollution index varied between 0.8426 and 4.7172, classifying samples as moderately to very highly polluted. Similarly, the synthetic pollution index (in the range of 0.5021-4.0715) revealed that none of the samples had excellent water quality, with various degrees of pollution categories. Nitrate Health Quotient (HQ) values indicated chronic human health risks ranging from low to severe, with newborns being the most vulnerable. Household use of nitrate-rich groundwater for showering and cleaning did not pose significant health risks. Fluoride HQ decreased with age, and children faced the highest risk of fluorosis. The Hazard Index (HI) yielded moderate to high-risk values. Nitrate risks were 1.21 times higher than fluoride risks, as per average HI assessment. All samples fell into the vulnerable category based on the Total Hazard Index (THI), with 88.89% classified as very high risk. This research provides valuable insights into groundwater quality, guiding water authorities, inhabitants, and researchers in identifying safe water sources and vulnerable human populations. The results highlight the need for appropriate treatment techniques and long-term coastal groundwater management plans.

The process of sexual reproduction in eukaryotes starts when gametes from two different sexes encounter each other. Paramecium, a unicellular eukaryote, undergoes conjugation and uses a gametic nucleus to enter the sexual reproductive process. The molecules responsible for recognizing mating partners, hypothetically called mating-type substances, are still unclear. We have identified an O3-type mating substance polypeptide and its gene sequence using protein chemistry, molecular genetics, immunofluorescence, RNA inter-ference, and microinjection. The O3-type substance is a polypeptide found in the ciliary membranes, located from the head to the ventral side of cells. The O3-type substance has a kinase-like domain in its N-terminal part located outside the cell and four EF-hand motifs that bind calcium ions in its C-terminal part located inside the cell. RNA interference and immunofluorescence revealed that this polypeptide positively correlated with the expression of mating reactivity. Microinjection of an expression vector incorporating the O3Pc-MSP gene induced additional O3 mating type in the recipient clones of different mating types or syngen. Phylogenetic analysis indicates this gene is widely present in eukaryotes and exhibits high homology among closely related species. The O3Pc-MSP gene had nine silent mutations compared to the complementary mating type of the E3 homologue gene.

(1) Background: Among the chronic complications of type 2 diabetes mellitus, cancer became the leading cause of death in several countries. Our objective was the determination of whether prevalent type 2 diabetes mellitus is associated with a higher incidence of cancer. (2) Methods: This study is a nationwide analysis performed in Hungary. Study population was divided into a group with type 2 diabetes mellitus and into a non-diabetic group. The primary outcome was the risk related to overall cancer incidence. A key secondary outcome was the overall incidence of cancer in distinct study years. Further outcomes were the annual percent changes. (3) Results: The odds ratio related to the overall incidence of cancer was 2.50 (95% confidence interval: 2.46-2.55, P<0.0001) in patients with diabetes as related to controls. The odds ratio was higher in males than in females. The highest risk was found in the 18-39-year-old subgroup. The annual cancer incidence rate declined in controls, but not in patients with diabetes. Several types of cancer showed a decreasing tendency in non-diabetic controls.; (4) Conclusions: type 2 diabetes is associated with a higher risk of cancer. High risk in young patients with type 2 diabetes suggests that these young individuals should be considered as a risk group.

(1) Background: Patients with type 2 diabetes mellitus (T2DM) are at higher risk of cancer but how these two diseases associate is still debated. The goal was the assessment of the overall incidence of cancer among patients with newly diagnosed T2DM in Hungary. Summarizing, incident T2DM is associated with a significantly higher overall risk of incident cancer, with a reverse correlation of age. Newly registered T2DM patients were suggested to be screened for cancer within 6 months. (2) Methods: A nationwide, retrospective, longitudinal study was performed using a Hungarian database. The incident T2DM and diabetes free Hungarian population were included in the study. The primary endpoints were the overall and site-specific incidence and annual percentage change of the incidence of cancer in both populations. (3) Results: The overall incidence of cancer in patients amounted to 29.4/1000 and 6.6/1000 with or without T2DM, respectively, and the OR (95%CI) of cancer of the T2DM group was 4.32 (4.14-4.53), p<0.0001. The risk of having cancer was age-dependent, having the highest odd in the age group 18-39. The incidence of cancer was declining in the non-diabetic but was unchanged in T2DM population. The average lag time of diagnosing a cancer after the detection of T2DM was 3.86 months.; (4) Conclusions: Iincident T2DM is associated with a significantly higher overall risk of incident cancer, with a reverse correlation of age. Newly registered T2DM patients were suggested to be screened for cancer within 6 months.

Diabetes mellitus (DM) poses a significant challenge to global health, with its prevalence projected to rise dramatically by 2045. This narrative review explores the bidirectional relationship between periodontitis (PD) and type 1 diabetes mellitus (T1DM), focusing on cellular and molecular mechanisms derived by the interplay between oral microbiota and the host immune response. A comprehensive search of literature published between 2008 and 2023 was conducted to elucidate the association between these two diseases. Preclinical and clinical evidence suggests a bidirectional relationship, with individuals with T1DM exhibiting heightened susceptibility to periodontitis, and vice versa. The review includes recent findings from human clinical studies, revealing variations in oral microbiota composition in T1DM patients, including increases in certain pathogenic species such as Porphyromonas gingivalis, Prevotella intermedia, and Aggregatibacter actinomycetemcomitans, along with shifts in microbial diversity and abundance. Molecular mechanisms underlying this association involve oxidative stress and dysregulated host immune responses, mediated by inflammatory cytokines such as IL-6, IL-8, and MMPs. Furthermore, disruptions in bone turnover markers, such as RANKL and OPG, contribute to periodontal complications in T1DM patients. While preventive measures to manage periodontal complications in T1DM patients may improve overall health outcomes, further research is needed to understand the intricate interactions between oral microbiota, host response, periodontal disease, and systemic health in this population.

The vomeronasal system serves as a pivotal element in mammalian sensory biology, allowing the perception of chemical signals essential for social communication via the activation of two main receptor families, V1R and V2R. The expression of V1Rs and V2Rs is linked with that of the G-protein alpha-subunits, Gαi2 and Gαo, respectively. The exploration of the evolutionary pathways of V1Rs and V2Rs across all mammalian species remains a main challenge, juxtaposing available genomic data against emerging immunohistochemical evidence. However, recent investigations, in contrast to what is predicted by the currently annotated genomic sequences, have revealed the expression of Gαo in the vomeronasal neuroepithelium of wild canids, including wolves and foxes. In the present study, the employment of a specific antibody raised against the mouse V2R2, member of the C-family of vomeronasal receptors, V2Rs, has confirmed the expression of this receptor in the fox and wolf, but it has revealed the lack of expression in the dog. This may reflect the impact of domestication on the regression of the VNS in this species, in contrast to their wild counterparts, and underscores the effects of artificial selection on sensory functions. Thus, these findings suggest a more refined chemical detection capability in wild species.

The article presents a simplified method for determining the strength of a corrugated board packaging subjected to dynamic transport loads. The proposed algorithm consists of several calculation steps: (1) a static analysis of the compressive strength of the package, (2) an analysis of random vibrations in the frequency domain, used to determine the resonance frequencies, and (3) a dynamic analysis of the package loaded with computed resonant frequencies. For this purpose, numerical models of the static compression test of the packaging before and after the dynamic analysis of the package subjected to general transport loads were developed. In order to validate the model, the laboratory packaging compression tests were also performed for samples of boxes with 3-layer cardboard. Thanks to this, it was possible to verify the results of numerical simulations of compression tests for several box geometries. Which, in turn, allowed for the development of a method based on dynamic and post-dynamic (static) numerical analysis, allowing to determine with high accuracy the resistance of selected packaging to vibrations and dynamic loads. The results of the (validated experimentally) numerical analysis prove the usefulness of the simplified method presented here for precise estimation of the load capacity of various packages dynamically loaded during transport.

Public restrooms are often a hub of microbial contamination, and the examination of bacterial contamination in these facilities can serve as an important indicator of the transmission of infectious diseases. This study was conducted to determine the prevalence of bacterial contamination in public restrooms based on the economic class of the building. Samples were collected from various spots in 32 restrooms found in 10 shopping malls, classifying them into two categories: upper-end restrooms and lower-end restrooms. The findings showed that the level of contamination was higher in the lower-end restrooms, with the seat being the most contaminated area. The most dominant Gram-positive bacteria were coagulase-negative staphylococci species, making up 86% of the identified Gram-positive isolates. The most dominant Gram-negative bacteria identified were Klebsiella pneumoniae and Pseudomonas aeruginosa. The antibiotic sensitivity test results revealed the presence of multi-drug resistant bacteria among the Gram-positive and negative isolates, including Staphylococcus haemolyticus, Staphylococcus kloosi, Acinetobacter baumanii, and Pseudomonas aeruginosa. In conclusion, the study underscores the significance of monitoring bacterial contamination in public restrooms and the need for measures to reduce the spread of infectious diseases. Further research is crucial to gain a complete understanding of the bacterial contamination in public restrooms and their resistance patterns, to ensure the safety and health of the public. The implementation of improved cleaning practices and hands-free designs in restrooms can help reduce the risk of cross-contamination and prevent the spread of diseases.

The weight coefficients of the diaphragm spring depend on experiences in the traditional optimization. However, this method not only cannot guarantee the optimal solution but it is also not universal. Therefore, a new optimization target function is proposed. The new function takes the minimum of average compress force changing of the spring and the minimum force of the separation as total objectives. Based on the optimization function, the result of the clutch diaphragm spring in a car is analyzed by the non-dominated sorting genetic algorithm (NSGA-II) and the solution set of Pareto is obtained. The results show that the pressing force of the diaphragm spring is improved by 4.09%by the new algorithmand the steering separation force is improved by 6.55%, which has better stability and steering portability. The problem of the weight coefficient in the traditional empirical design is solved. The pressing force of the optimized diaphragm spring varied slightly during the abrasion range of the friction film, and the manipulation became remarkably light.

The damage evolution rules of coal under true triaxial combined static-dynamic loads are important to understand and reveal the mechanism of rockburst in coal mines. The numerical simulation was carried out using FLAC3D to explore the coupling effect of static and dynamic stress, especially the influence of dynamic load parameters. The results show that the increase of dynamic load amplitude not only makes the plastic zone grow exponentially and shorten the damage development time, but also decreases the residual strength of the coal sample, which leads to a much more violent of the dynamic failure. The stress wave can propagate more stable in the coal sample with the increase of dynamic load frequency and the development time of the plastic zone also show synchronous fluctuating features, and when the frequency is like the intrinsic frequency of the coal sample, the dynamic load has a significant stimulate effect. The static and dynamic loads have different damage effect to the coal sample under true triaxial stress path, the weight decreases in order of the minimum principal stress, the maximum principal, the amplitude of the dynamic load and at last the dynamic stress frequency by the entropy weight method analysis.

Although the similarity laws were widely used in impact fields, the scaling relations of anisotropic elastic structures often were broken when the geometric distortion (not equal scaling in different spatial directions) and the material distortion (different materials used for scaled model and full-size prototype) were considered. To overcome the difficulty of geometric and material distortion, a directional framework of similarity laws, termed as oriented-density-length-velocity (ODLV) system, is proposed for the anisotropic elastic structure under impact loads. Different from previous similarity law systems using scalar dimensional analysis, the directional similarity law framework mainly considers spatial anisotropy for structural geometry and material parameters. Based on the oriented dimensional analysis and the orthotropic Hooke's law, directional dimensionless numbers and directional scaling relations with geometric power properties for the elastic modulus and the Poisson's ratio are presented systematically. By selecting the dominant material parameters controlling similarity, three important scaling techniques with correction of geometric width and thickness are proposed to compensate for the difficulty of distortion. A clamped square plate with different anisotropic and isotropic elastic materials subjected to dynamic pressure pulse is verified numerically and discussed in detail. The results show that the thin square plate prototype must be scaled to be the thinner/thicker rectangular plate, and the components of displacement, stress and strain between scaled model and full-scale prototype behave good consistency in both spatial and temporal fields.

This study explores optimizing Synthetic Aperture Radar (SAR) satellite constellation scheduling for multi-imaging missions in densely targeted areas using an in-house developed Modified Dynamic Programming (MDP) algorithm. By employing Mixed-Integer Linear Programming (MILP) to define the mission planning problem, the research aims to maximize observation of high-value targets within restricted planning horizons. Numerical simulations, covering a wide range of target numbers and satellite configurations, reveal the MDP algorithm’s superior mission allocation efficiency, enhanced success rates, and reduced revisit times, compared to the Greedy algorithm. The findings underscore the MDP algorithm’s improved operational efficiency and planning robustness for complex imaging tasks, demonstrating significant advancements over traditional approaches.

Berberis vulgaris L. (Berberidaceae) is a shrub that has been widely used in European folk medicine as an anti-inflammatory and antimicrobial agent. The purpose of our study was to elucidate the mechanisms of antiproliferative action of the plant’s methanolic root extract (BVR) against colon cancer cells. Cytotoxicity and pro-apoptotic activity were determined in human colon adenocarcinoma cell lines (LS180 and HT-29) and control colon epithelial CCD841 CoN cells. According to the MTT assay, after 48 h of cell exposure, the IC50 values were as follows: 4.3; 46.1 and 50.2 µg/mL for LS180, HT-29, and CCD841 CoN cells, respectively, showing the greater sensitivity of cancer cells to BVR. The Cell Death Detection ELISAPLUS kit demonstrated that BVR induced programmed cell death only against HT-29 cells. RT-qPCR with relative quantification method showed significant changes in the expression of genes related to apoptosis in both colon cancer cell lines. The genes BCL2L1 (126.84-366.66%), BCL2L2 (277.08-330.12%), CASP3 (180.36-261.36%) and CASP9 (158.08-213.46%) had significantly elevated expression, while BCL2 (23.08-52.06%) had reduced expression. Furthermore, in a panel of antioxidant tests, BVR showed positive effects (63.93±0.01, 122.92±0.01, and 220.29±0.02 mg Trolox equivalents (TE)/g in the DPPH•, ABTS•+ and ORAC assays, respectively). In the lipoxygenase (LOX) inhibition test, BVR revealed 62,60±0.87% of enzyme inhibition. The chemical composition of BVR was determined using UHPLC-UV-CAD-MS/MS analysis and confirmed the presence of several known alkaloids, including berberine, as well as other alkaloids and two derivatives of hydroxycinnamic acid (ferulic and sinapic acid hexosides). This is the first such extensive assessment of the biological activity of BVR. The results are very promising and encourage for the use of BVR as a comprehensive chemopreventive agent (anti-inflammatory, antioxidant, and pro-apoptotic) in colorectal cancer.

Weaving is an ancient and effective structural forming technique characterized by the ability to convert two-dimensional ribbons to three-dimensional structures. However, most 3D structures woven from straight ribbons have topological defects. Baek et al. proposed a method to weave smoother continuous 3D surface structures using naturally curved (in-plane) ribbons, obtained a new surface structure with relatively continuous variation of Gaussian curvature, and analyzed its geometric properties. We believe that this new 3D surface structure with smooth geometric properties must correspond to new mechanical properties. To this end, we investigated a 3D surface structure using naturally curved (in-plane) ribbon weaving, and the results of calculations and experiments show that such structures have better buckling stability than those woven with straight ribbons. It is observed that the number of ribbons influences the buckling behavior of different types of woven structures.

Based on the two-node Euler-Bernoulli beam, the tower system is discretized by finite element method, and the cubic Hermite polynomial is taken as the shape function of the beam element, and the structural characteristic matrix of the tower system is calculated, and the wind turbine-nacelle-tower multi-degree of freedom is established Finite element numerical model. The aerodynamic load calculation formula for any nacelle attitude angle is deduced. The influence of the vibration feedback of the flexible tower on the aerodynamic load of the wind turbine is studied. The results show that when the rigidity of the tower is large, the impact of tower vibration feedback on the aeroelastic load of the wind turbine is small. For a tower system with greater flexibility, the time-varying feedback of wind-induced vibration will cause greater aeroelastic load changes, especially the overturning moment of the tower top, which will cause a greater impact on the dynamic behavior of the tower in the downwind and crosswind directions. As the flexibility of the tower system increases, the interaction between tower vibration and aerodynamic load is gradually increasing. Taking the impact of the flexible tower on the aeroelastic load of the wind turbine into account, on the one hand, helps to predict the wind more accurately. The aerodynamic load of the wind turbine improves the efficiency of wind energy utilization. On the other hand, it can more accurately analyze the dynamic behavior of the flexible structure of the wind turbine, which is extremely beneficial to the structural optimization design of the wind turbine.

Demand response flexible loads can provide fast regulation and ancillary services as reserve capacity in power systems. This paper proposes a joint optimization dispatch control strategy for source-load system with stochastic renewable power injection and flexible thermostatically controlled loads (TCLs) and plug-in electric vehicles (PEVs). Specifically, the optimization model is characterized by a chance constraint look-ahead programming to maximal the social welfare of both units and load agents. By solving the chance constraint optimization with sample average approximation (SAA) method, the optimal power scheduling for units and TCL/PEV agents can be obtained. Secondly, two demand response control algorithms for TCLs and PEVs are proposed respectively based on the aggregate control models of the load agents. The TCLs are controlled by its temperature setpoints and PEVs are controlled by its charging power such that the DR control objective can be fulfilled. The effectiveness of the proposed dispatch and control algorithm has been demonstrated by the simulation studies on a modified IEEE 39 bus system with a wind farm, a photovoltaic power station, two TCL agents and two PEV agents.

Abstract: Safety issues related to the electrification of more electric aircraft (MEA) need to be addressed because of the increasing complexity of aircraft electrical power systems and the growing number of safety-critical sub-systems that need to be powered. Managing the energy storage systems and the flexibility in the load-side plays an important role in preserving the system’s safety when facing an energy shortage. This paper presents a system-level centralized operation management strategy based on model predictive control (MPC) for MEA to schedule battery systems and exploit flexibility in the demand-side while satisfying time-varying operational requirements. The proposed online control strategy aims to maintain energy storage (ES) and prolong the battery life cycle, while minimizing load shedding, with fewer switching activities to improve devices lifetime and to avoid unnecessary transients. Using a mixed-integer linear programming (MILP) formulation, different objective functions are proposed to realize the control targets, with soft constraints improving the robustness of the model. Besides, an evaluation framework is proposed to analyze the effects of various objective functions and the prediction horizon on system performance, which provides the designers and users of MEA and other complex systems with new insights into operation management problem formulation.

Lake Rawa Besar is an urban lake surrounded by dense settlements and market area. Currently Lake Rawa Besar is experiencing physical and ecology strain. This research’s objectives are to determine the levels of sediment and nutrient, the distribution, also the relation to land use and human activities producing pollutant. Field surveys with 30 sample points and observations was needed scattered within the lake. Measuring the value of each parameter is carried out in national standardized laboratory. The result shows that sediment load of TDS is still below the standard limit for clean water, while TSS levels in the middle of lake exceed the standard limit. Nutrient loads, spesifically nitrate and phospate levels is below the standard limit. While turbidity and BOD levels have a uniform distribution pattern in the lake, exceed the standard limit for clean water, and have a positive correlation. High levels of turbidity and BOD are caused by household waste and human activities producing organic waste such as tofu factory, fowl manure, and garbage dump. Small sewage goes into the lake mediates pollutants inflow. Attention is needed by nearby people, also for the government, to sustain the ecological condition of the lake.

Functional connectivity (FC) is a potential candidate that can increase the performance of brain-computer interfaces (BCIs) in the elderly because of its compensatory role in neural circuits. However, it is difficult to decode FC by current machine learning techniques because of a lack of its physiological understanding. To investigate the suitability of FC in BCI for the elderly, we propose the decoding of lower- and higher-order FCs using a convolutional neural network (CNN) in six cognitive-motor tasks. The layer-wise relevance propagation (LRP) method describes how age-related changes in FCs impact BCI applications for the elderly compared to younger adults. Seventeen younger (24.5±2.7 years) and twelve older (72.5±3.2 years) adults were recruited to perform tasks related to hand-force control with or without mental calculation. CNN yielded a six-class classification accuracy of 75.3% in the elderly, exceeding the 70.7% accuracy for the younger adults. In the elderly, the proposed method increases the classification accuracy by 88.3% compared to the filter-bank common spatial pattern (FBCSP). LRP results revealed that both lower- and higher-order FCs were dominantly overactivated in the prefrontal lobe depending on task type. These findings suggest a promising application of multi-order FC with deep learning on BCI systems for the elderly.

This paper presents experimental identification and vibration suppression of a flexible manipulator with non-collocated piezoelectric actuators and strain sensors using optimal multi-poles placement control. To precisely identify the system model, a reduced order transfer function with relocated zeros is proposed, and a first-order inertia element is added to the model to compensate the non-collocation. Comparisons show the identified model match closely with the experimental results both in the time and frequency domains, and a fit of 97.2% is achieved. Based on the identified model, a full-state multi-poles placement controller is designed, and the optimal locations of the closed loop poles are determined. The feasibility of the proposed controller is validated by simulations. Moreover, the controller is tested for different locations of the closed loop poles, and an excellent performance of the optimal locations of the closed loop poles is shown. Finally, the effectiveness of the proposed controller is demonstrated by experiments. Results show that the vibrations of the expected modes are significantly diminished. Besides, vibrations of the higher modes are also slightly suppressed. Accordingly, multi-mode vibrations of the manipulator are well attenuated, and the tip displacement converges quickly with the proposed method.

The purpose of the present study was to develop an experimental model for studying of the intra-articular knee movements depending on the work of the knee joint and applied muscle groups in isometric stretching conditions with different tens. The experimental procedure includes ultrasound examination of a knee joint after isometric stretching of healthy men (n=32). The changes in millimeters of the distances between the femur and tibia were measured with ultrasound sonographer at three stages. The first stage was performed on ten (n=10) healthy men at five different sitting and upright positions. In the second and third experimental model stages the lower limbs loading was on 22 participants. Our hypothesis which was confirmed, was that as a result of increasing extraloads on the participants back (2, 5, 10, 15, 17, 20 kg), a intra-articular decrease in the femur-tibia cartilage surface distance wiil be observed. The accuracy of the created experimental model was improved over its three stages from 30% to 9%. Quantitative model data can help to create a mathematical model for the mechanical effects during deformation of the knee joint bone cartilage, as well as to outlines the some future tasks: increasing loading weights; enlarge participant groups; comparison men and women; healthy and pathology comparison.

The article concerns problems related to the assessment of reactive power in power networks with non-linear, fast-varying loads, such as electric arc furnaces, rolling mill drives, etc. The operation of this type of loads is characterized by the introduction of interharmonic currents (including higher harmonics) into the power supply network and a relatively low power factor. Rapid changes in the RMS value of the current also cause voltage fluctuations and the related phenomenon - flicker. Therefore, there is a need to evaluate the selection of power of compensating devices taking into account the random nature of load changes and the distortion of current and voltage waveforms, in particular interharmonic components, the impact of which has not been fully investigated so far. To analyze the random nature of load changes, autocorrelation functions were used, which allowed for the estimation of the expected values of the arc furnace current distortion coefficient (based on the recorded waveforms). In order to determine the parameters of reactive power compensating devices, and in particular capacitor banks, an autocorrelation function in the exponential-cosine-sine form was used, which meets the conditions of differentiation. The article contains comparative results of calculations of the reactive power of capacitor banks determined using different methods.

This paper presents results from numerical simulations validated by experimental results related to the effects of DSSI on the dynamic response of bridges. An in-service overpass was shaken using the T-Rex, a large-amplitude mobile shaker from the National Hazards Engineering Research Infrastructure (NHERI) facilities. Studies implementing Finite Element Modeling to develop time histories, response spectra, and eigenmodes were conducted in a forward-modeling problem setup. Two models were created to assess the DSSI effects on the dynamic response of the bridge. One model included elements that incorporate DSSI effects, while the other had fixed-base boundary conditions. The response from the DSSI FEM model matched the field results better than the fixed-base model, in terms of the peak response amplitudes and identified natural frequencies and modes. The influence of a series of factors, such as the soil shear wave velocity, bridge height, bridge foundation embedment depth and the corresponding rigidity, slenderness, and embedment ratios, on the bridge response is presented.

Weaving technology can convert two-dimensional structures such as ribbons into three-dimensional structures by specific connections. However, most of the 3D structures fabricated by conventional weaving methods using straight ribbons have some topological defects. In order to obtain smoother continuous 3D surface structures, Baek et al. proposed a novel weaving method using naturally curved (in-plane) ribbons to fabricated three-dimensional curved structures and using this method to weave new spherical weave structures that are closer to perfect spheres. We believe that this new spherical weave structure with smooth geometric properties must correspond to new mechanical properties. To this end, we investigated the buckling characteristics of different types of spherical weave structures by the combination of test and finite element method. The results of calculations and experiments show that the failure mode of the spherical weave structure under vertical loading can be divided into two stages: a flat contact region forms between the spherical weave structure and the rigid plate and inward dimple of ribbons. The spherical weave structures using naturally curved (in-plane) ribbon weaving have better buckling stability than those woven with straight ribbons. The vertical buckling load of spherical weave structures using naturally curved ribbon increases with the width and thickness of the ribbon. In addition, this paper combines test, theoretical and finite element analysis to propose the buckling load equation and buckling correction factor equation for the new spherical weave structure under vertical compression load.

To implement renewable energy resources, microgrid systems have been adopted and developed into the technology of choice to assure mass electrification in the next decade. Microgrid systems have a number of advantages over the conventional utility grid systems, however, it faces severe instability issues due to continually increasing constant power loads. To improve the stability of the entire system, load side compensation technique is chosen because of its robustness and cost effectiveness. In this particular occasion, a sliding mode controller is developed for microgrid system in the presence of CPL to assure certain control objective of keeping the output voltage constant at 480V. After that, the robustness analysis of the sliding mode controller against parametric uncertainties is presented. The sliding mode controller robustness against parametric uncertainties, frequency variations, and additive white Gaussian noise (AWGN) are illustrated in this paper. Later, the performance of the PID and sliding Mode controller is compared in case of nonlinearity, parameter uncertainties, and noise rejection to justify the selection of Sliding Mode controller over PID controller. All the necessary calculations are reckoned mathematically and results are verified in the virtual platform such as MATLAB/Simulink with the appreciable outcome.

Background: About 200 new ovarian cancer cases per year are diagnosed in Armenia, an upper-middle-income country. This study aims to summarize the survival outcomes of relapsed ovarian cancer patients in Armenia based on the type of relapse, risk factors, and the choice of systemic treatment. Methods: A retrospective case-control study including 228 patients with relapsed ovarian cancer from 3 different institutions. Results: The median age of the patients was 55. The median follow-up from the relapse and primary diagnosis was 21 and 48 months. The incidence of platinum-sensitive relapse was 81.6% (186), while platinum-resistant relapse was seen only in 18.4% (42) patients. Median survival of the patients starting from the primary diagnosis in the platinum-sensitive compared to the platinum-resistant group was 54 versus 25 months (p < 0.001), and median survival after relapse: was 25 versus 13 months, respectively 3- and 5-year survival in these groups were: 31.2% vs. 23.8%, and 15.1% vs. 9.5%, respectively (p = 0,113). Conclusions: Overall, despite new therapeutic approaches, ovarian cancer continues to be one of the deadly malignant diseases in women, especially, in developing countries with a lack of resources, where, in fact, the main available systemic treatment for the majority of patients remains chemo-therapy. Low survival rates emphasize the urgent need for more research on this group of patients with poor outcomes.

This paper focus on the modeling and time-domain analyzing method of piecewise-smooth fractional-order circuit systems. Firstly, an analytical framework is constructed based on a generalized piecewise-smooth two-port impedance network model, which takes the topological characteristics of Dickson type switched-capacitor converters (SCCs) as examples, and considers the fractional-order characteristics of class-2 X7R ceramic capacitors, which are widely used in SCCs. Secondly, the time-domain analyzing method for such a piecewise-smooth fractional-order circuit system is developed, numerical solutions are obtained, and the influence of the fractional-order capacitor on the power conversion efficiency of the system are revealed. Finally, in order to validate the analysis, both numerical simulation and experiments are provided in the work, the results of which confirm that, the proposed fractional-order analytical framework can capture the power loss mechanism of piecewise-smooth fractional-order circuit systems more effectively than the traditional integer-order based approach, thus benefiting the design of circuit systems.

The paper presents a new type of hydraulic clutch operating with magnetorheological (MR) fluids and the results achieved from both theoretical analysis and experimental measurement. The hy-draulic clutch system of its own design with MR working fluid and a rotating magnetic field lo-cated is designed. The principle of this clutch is to use a rotating magnetic field created by an al-ternating current electromagnet to set the MR fluid in motion. In the tests of the hydraulic clutch with a rotating magnetic field, MR fluid produced on their own, consisting of solid iron particles of various diameters mixed with a silicone oil, are used as working fluids. The rheological properties of MR fluids are assessed on the basis of tests carried out with a Brookfield DV2T rheometer equipped with a magnetic device for generating the magnetic field of its own design. The char-acteristics of the hydraulic clutch with MR working fluid and the rotating magnetic field are tested on a specially built test stand. As a result of the research, it has been found that the torque transmitted by the clutch is the greater, the higher the rotational speed of the magnetic field and the lower the rotational speed of the beaker in which the working fluid is placed, and that the greatest torque occurs for the working fluid with the highest iron content. Based on the analysis of the structure and characteristics of the clutch in which the magnetic field is used, it has been shown that the design of the developed clutch is similar to that of an induction clutch, and its characteristics correspond to the characteristics of the eddy current clutch. Therefore, the proposed new clutch working with MR fluid and the rotating magnetic field can be applied to stationary power transmission system similarly to an eddy current clutch.

PHA synthases (PhaC) are grouped into four classes based on the kinetics and mechanisms of reaction. The grouping of PhaC enzymes into four classes is dependent on substrate specificity, according to the preference in forming short chain length (scl) or medium chain length (mcl) polymers: class I, class III, and class IV produce scl-PHAs depending on propionate, butyrate, valerate and hexanoate precursors, while class II phaC synthesize mcl-PHAs based on the alkane (C6 to C14) precursors. PHA synthases of class I, in particular PhaC_Cs from Chromobacterium USM2 and PhaC_Cn/RePhaC1 from Cupriavidus necator/R. eutropha, have been analysed and the crystal structures of the C-domains have been determined. PhaC_Cn/RePhaC1 was also studied by small angle X-ray scattering (SAXS) analysis. Models have been proposed for dimerization, catalysis mechanism, substrate recognition and affinity, product formation and product egress route. The assays based on amino acid substitution by mutagenesis have been useful to validate the hypothesis on the role of amino acids in catalysis and in accommodation of bulky substrates, for the synthesis of PHB co-polymers and medium chain length-PHA polymers with optimized chemical properties.

The dynamic evolution and variation of electrical loads is now a priority for optimum management and, above all, forecasting. Indeed, these dynamic load variations require computer tools able to implement optimal load forecasting models. Scientific research into automated models for forecasting electrical loads therefore represents a challenge for scientific researchers. Several research studies have therefore been carried out. These include machine learning approaches such as: LSTM (Long Short-Term Memory), Support Vector Machine (SVM) and others. This article proposes a comparison study between a hybrid model based on the wavelet transform coupled with the adaboost method, and LSTM, for forecasting electricity consumption loads. Python 3.10 was used for the studies. The first results obtained consisted in the study of electricity load forecasts over four (04) data sets of the year (January, April, August and December). These results are very satisfactory, showing a good correlation between the real results of the electrical load consumption data, and the results of the implemented model. The electrical load consumption data are collected from a renewable energy production source: photovoltaic solar energy. The model test results (R2) obtained range from 0.919 to 0.958. These results are representative of real data and reflect the model's performance. The second set of results concerns a comparative study between the methods used by Y. Xie et al (CNN, MLP, LSTM-AM and LSTM-AM-MLP), and our approach. The prediction results obtained between the approaches show a prediction gap ranging from 0.15 to 0.78 for RMSE and 0.83 for MAPE. These results show significant differences between the methods. The minimization of errors by our model, therefore, reflects the model's performance in terms of accuracy, which is necessary for the optimal management of consumer electricity load forecasts in order to ensure balance between supply and demand.