This work exclusively focuses on the assessment of the thermal performance of a multifunctional facade panel incorporating PCM in foam layers, recurring to a hot box heat flux meter method to determine the thermal transmittance (U-value). The experimental setup is based on the steady-state approach using climatic chambers, assuring a stable thermal environment. Even small fractions of PCM achieved a small reduction in thermal amplitude. Numerical simulations using Ansys Fluent were developed to evaluate the performance of PCM use over a wide range of temperature boundary conditions and operating modes. These numerical models were calibrated and validated using the results of experimental tests, achieving a correlation factor of 0.9674, thus accurately representing a real-world scenario. The decrement factor (f) was used to analyse the data. It was identified that the efficiency of the panel and size of the optimum region increased with the PCM fraction growth. The simulated behaviour was optimum when the input mean temperature is of 20 °C for a room temperature of between 18-20 °C. The results show the significant potential of the multi-layered panel and the thermal regulator effect of the PCM incorporated on indoor space temperature to reach good thermal comfort levels.

This study investigates the transformation of Bubungan Tinggi, a traditional Banjar house with a high roof, into a modern home through the integration of modern facade design with traditional Bubungan Tinggi facade elements. Bubungan Tinggi is a monumental artifact in South Kalimantan representing the collective memory of the Banjar community with its distinctive typology and anatomy. This study uses a qualitative approach with design experiments to explore the integration of smart home systems, eco-friendly materials, and contemporary design principles. The findings highlight the potential of blending traditional architecture with modern innovations to create sustainable, smart, and culturally sensitive housing solutions.

Solar energy is one of the most important renewable energy sources for many settings, such as households, solar-powered vehicles, power grid support, etc. However, the amount of solar energy produced is directly proportional to the surface area of the solar panel exposed to the sun rays, and so the challenges arise for the space required to install solar panels in order to get maximum area coverage of sun radiation energy absorption in constricted spaces such as vehicles powered by solar, small residential apartments, etc. The challenge with solar energy is that once a plate is installed, the space under it or above it cannot be used for another solar panel installation. This is due to the fact that the shadow cast by the above solar panel or structure prevents sun rays from reaching the below solar panel. The introduction of flexible solar panels that can take on any shape has given us the opportunity to explore the possibility of maximising solar plate surface area using surface manifold techniques. In this optimisation study, the constraint is that we have a space with fixed dimensions of length, width, and height, and the objective is to maximise the surface area of the panel within the given space dimensions to maximise solar energy absorption. Thus, this paper then proposes curving the panel surface and/or protruding the surfaces of the panel using the concept of a topology surface manifold to maximise the surface area: Protruding panel surface with shapes such as pyramidal, cone, hemisphere, sinusoidal wavy curve, etc. are analysed to check if the panel surface increases at all. The geometrical design result shows that the panel surface can increase by more than 20%. Although this paper only presents concept work and details of experimental design are yet to be performed, it should also be noted that curving surfaces have drawbacks, such as some protruding parts of solar panels when the plate is tilted, not facing the sun directly, which may cast shadows on parts of the solar panel, causing hindrance.

Panel data of our interest consist of a moderate number of panels, while the panels contain a small number of observations. An estimator of common breaks in panel means without a boundary issue for this kind of scenario is proposed. In particular, the novel estimator is able to detect a common break point even when the change happens immediately after the first time point or just before the last observation period. Another advantage of the elaborated change point estimator is that it results in the last observation in situations with no structural breaks. The consistency of the change point estimator in panel data is established. The results are illustrated through a simulation study. As a by-product of the developed estimation technique, a theoretical utilization for correlation structure estimation, hypothesis testing, and bootstrapping in panel data is demonstrated. A practical application to non-life insurance is presented as well.

Aiming at the limitations of single-functionality, limited applicability, and complex designs prevalent in current metasurfaces, we propose a terahertz multifunctional and multiband tunable metasurface utilizing a VO2-metal hybrid structure. This metasurface structure comprises a top VO2-metal resonance layer, a middle polyimide dielectric layer, and a gold film reflective layer at the bottom. This metasurface exhibits multifunctionality, operating independently of polarization and incident angle. The varying conductivity states of the VO2 layers, enable the metasurface to achieve various terahertz functionalities, including single-band absorption, broadband THz absorption, and multiband perfect polarization conversion for linear (LP) and circularly polarized (CP) incident waves. Finally, we believe that the functional adaptability of the proposed metasurface expands the repertoire of options available for future terahertz device designs.

Current commitments by European governments seek to improve energy consumption as a means to reduce carbon emissions from building stock by 2050. Within such context, retrieving reliable three-dimensional contours from point clouds becomes an important step in developing facade retrofitting solutions since facade retrofitting projects often make use of as-built 3D models to help reduce inaccuracies by narrowing interpretation and measurement errors. This work aims to provide a method that uses topology-based parametric modelling for reconstructing building envelopes from point clouds. Through a semi-automated process that gives permanent visual feedback, the user adjusts parameters to custom standards of acceptability. A solution under the form of a Grasshopper definition delivers building envelope 3D contours in various file formats as a means for increasing interoperability. The main contributions of this work consist of a parametric reconstruction workflow capable of solving building topology for retrieving 3D contours, a strategy to bypass point cloud occlusion, and a strategy for converting those contours into an IFC model directly from the parametric modelling environment.

Postbiotic is a preparation of inanimate microorganisms and/or their components that confers a health benefit on the host. Different bacterial strain and preparation method result in different functions. Herein, a postbiotic preparation named Postbiotic-P by intercepting 1-5 KD of the cell-free supernatants of L. caseiparacasei P6 fermentation broth was prepared, and its multifunctional activities were evaluated. The results showed that Postbiotic-P exerted good antihemolytic (10%-50% Postbiotic-P resulted in 4.9%-48.1% antihemolytic rate), anti-inflammatory (8% to 40% Postbiotic-P is comparable to 259.1-645.4 μg/mL of diclofenac sodium equivalents), antioxidant [reducing power (1.25%-12.5% Postbiotic-P resulted in the increase of OD700 from 0.279-2.322), DPPH free radical scavenging activity (2.5%-50% Postbiotic-P resulted in 38.9%-92.4% free radical scavenging rate), and hydroxyl radical scavenging activity (0.5%-4% Postbiotic-P resulted in 4.66%-10.38% hydroxyl radical scavenging rate)], and antimicrobial activities (against 2 Gram-positive, 8 Gram-negative and 1 fungus). Furthermore, it was proved that Postbiotic-P could significantly inhibit the increase of the peroxide value and the malondialdehyde content in cookies, indicating the application potential of Postbiotic-P in food preservation. Taken together, Postbiotic-P has good application potential for the development of health care products and functional foods. However, further studies are needed to determine their precise mechanism of action, to clarify the active components responsible for the function, and to validate the biological activities in animal models or clinical trials.

In the construction sector, the integration of biobased materials has emerged as a pivotal aspect of EU policies, aimed at promoting sustainable practices throughout the value chain to mitigate resource consumption and carbon emissions. This paper explores the development and validation activities of a bio-based façade system within the Basajaun H2020 project, focusing on enhancing the utilization of biobased components within building envelopes to replace conventional solutions with eco-friendly alternatives. This paper reports the methodologies employed to detect requirements and outline the testing protocols undertaken to validate the façade system design devised within the project focusing on the original façade components as the bio composite profile. Vision and opaque façade modules are prototyped and tested following curtain wall standards standard for performance and acoustic assessments, to showcase the efficacy of the developed solution. The conducted tests demonstrate the feasibility of integrating bio-based components into building envelopes, aligning with project expectations, and prevailing standards for curtain wall façade solutions. Notably, the designed façade system meets technical conditions and project objectives. Nevertheless, the research underscores the need for further refinements to facilitate solution industrialization and explore broader market applicability. Future efforts will focus on addressing these improvements and assessing the scalability of the solution.

Metasurface constitutes one of the most promising technologies for holographic imaging; however, the work for terahertz (THz) metasurface holographic imaging is relatively limited. Here, we propose a THz dielectric geometric-propagation phase metasurface, which can operate dual-mode (reflection and transmission) and reconfigurable multifunctional holographic imaging. The dual-mode is realized by controlling the Fermi energy level (Ef) of the graphene integrated into the metasurface unit, and the reconfigurable three-channel holographic imaging in reflection or transmission mode are achieved by switching the feed polarization among left-handed circular polarization (LCP), right-handed circular polarization (RCP) and linear polarization (LP). The metasurface is designed based on the transmission mode, and a physical model for switching to the reflection mode is established. For the first time to the best of our knowledge, a reflection-transmission dynamic modulation THz holographic imaging metasurface has been developed. The holographic metasurface operates in transmission mode at Ef = 0.1 eV, and in reflection mode at Ef = 0.9 eV. Compared with recently published holographic imaging metasurfaces, the proposed metasurface offers the following advantages: high holographic efficiencies (42.5% to 49%), more holographic imaging channels, dynamic modulation dual-mode operations, and reconfigurability.

Halide perovskite materials gain enormous attention for their semiconducting properties, higher power conversion efficiency and potential applications in a wide range field of studies along with their two key limitations: stability and toxicity. In spite of great progress made on the halide perovskites and many promising research developments, overcoming these limitations is not realized yet. Therefore, coordination engineering of new framework for obtaining alternative new halide perovskite materials and fundamental understanding of the coordination chemistry and electronic interactions forming the structure of these newly engineered halide perovskite materials might be one way in order to overcome the issues related to both stability and toxicity. In this review, the current development of halide perovskite families, both lead halide perovskites and lead free halide perovskites followed by coordination engineering of the new frameworks to engineer new halide perovskite materials will be reviewed comprehensively. Moreover, all the concerns of the fundamental ideas of coordination chemistry and electronic interactions that are keys in forming the halide perovskite structures are discussed in detail and form the main aim of this review. Interestingly, we also discuss recent potential energy applications beyond photovoltaic and this review has completed with an essential and open question: ‘what could happen in the future of halide perovskites?’ in order to excite commercial enterprises and research institutions again as well as to get motivating new predictions on the future continuity of this field.

In contemporary design practices, there is a disconnect between the design techniques used for early-stage design experimentation and performance analysis, and those used for the manufacture and construction. This study addresses the problems in developing an integrated digital design workflow and provides a research framework for integrating environmental performance requirements with robotic manufacturing processes on a construction site. The proposed method enables the user to import a design surface, identify design parameters, set several environmental performance goals, and thereafter simulate and select a robotic building strategy. Based on these inputs, design alternatives are developed and evaluated, considering their robotically simulated constructibility, in terms of their performance criteria. To validate the proposed method, the design is evaluated in an experiment wherein a double-skin facade perforation is generated using the proposed methodology. Initial results suggest a heuristic feature to improve the simulated robotic constructibility. Moreover, the functionality of the prototype is demonstrated.

Artificial Intelligence and especially machine learning have noticed rapid advancement on image processing operations. However, its involvement in the architectural design is still in its initial stages compared to other disciplines. Therefore, this paper addresses the issues of developing an integrated bottom up digital design approach and details a research framework for the incorporation of Deep Convolutional Generative Adversarial Network (GAN) for early stage design exploration and generation of intricate and complex alternative facade designs for urban infill. This paper proposes a novel building facade design by merging two neighboring building’s architecture style, size, scale, openings, as reference to create a new building design in the same neighborhood for urban infill. This newly produced building contains the outline, style and shape of the parent buildings. A 2D urban infill building design is generated as a picture where 1) neighboring buildings are imported as a reference using mobile phone and 2)iFACADE decode their spatial adjacency. It is depicted the iFACADE will be useful for designers in the early design stage to generate new façades depending on existing buildings in a short time that will save time and energy. Besides, building owners can use iFACADE to show their architects their preferred architecture facade by mixing two building styles and generating a new building. Therefore, it is depicted that iFACADE can become a communication platform in the early design stages between architects and owners. Initial results properly define a heuristic function for generating abstract design facade elements and sufficiently illustrate the desired functionality of our developed prototype.

In contemporary design practices, there is a disconnect between the design techniques used for early-stage design experimentation and performance analysis, and those used for the manufacture and construction. This study addresses the problems in developing an integrated digital design workflow and provides a research framework for integrating environmental performance requirements with robotic manufacturing processes on a construction site. The proposed method enables the user to import a design surface, identify design parameters, set several environmental performance goals, and thereafter simulate and select a robotic building strategy. Based on these inputs, design alternatives are developed and evaluated, considering their robotically simulated constructibility, in terms of their performance criteria. To validate the proposed method, the design is evaluated in an experiment wherein a double-skin facade perforation is generated using the proposed methodology. The results suggest a heuristic feature to improve the simulated robotic constructibility. Moreover, the functionality of the prototype is demonstrated.

Facade elements are known to represent a building component with multiple performance parameters to satisfy. Among others, “advanced facades” take advantage of hybrid solutions, like the assemblage of laminated materials. In addition to enhanced mechanical properties that are typical of optimally composed hybrid structural components, these systems are energy-efficient, durable, and offer lightening comfort and optimal thermal performance. This is the case of the structural solution developed in joint research efforts of the University of Zagreb and the University of Ljubljana, within the Croatian Science Foundation VETROLIGNUM project. The design concept involves the mechanical interaction of timber and glass load-bearing members, without sealing or bonded glass-to-timber surfaces. Laminated glass infilled timber frames are recognized as a new generation of structural members with relevant load-carrying capacity (and especially the enhancement of earthquake resistance of framed systems), but also energy-efficient and cost-effective solutions.

An actual problem of inertial navigation related to the creation of a multifunctional device that performs the functions of a meter for both angular velocities and linear accelerations is considered. The possibility of constructing such a device based on a hybrid-type modulation micromechanical gyroscope has shown. The ability to measure linear accelerations has provided by the presence of a small symmetrical distance between the axes of the elastic suspension relative to the center of mass of the sensor element. A mathematical model of the device ("heavy" gyroscope) as a high-quality three-dimensional oscillatory system is constructed. It has shown numerically that the reaction of the system to the movement of an object has, along with precession, the observed nutation. This allows you to develop an algorithm for separating information about the angular and linear motion of the base and implement a two-component angular velocity meter and a two-component linear acceleration meter in one device.

There are many uncertainties and risks in residential electricity consumption during the economic development. Knowledge of the relationship between residential electricity consumption and its key determinant—income—are important to the sustainable development of electric power industry. Using panel data from 30 provinces for the 1995-2012 period, this study investigates how residential electricity consumption changes as incomes increase in China. Previous studies typically used linear or quadratic double-logarithmic models imposing ex ante restrictions on the indistinct relationship between residential electricity consumption and income. Contrary to those models, we employed a reduced piecewise linear model that is self-adaptive and highly flexible and circumvents the problem of “prior restrictions.” Robust tests of different segment specifications and regression methods are performed to ensure the conservatism of the research. The results provide strong evidence that the income elasticity was approximately one, and it remained stable throughout the estimation period. The income threshold at which residential electricity consumption automatically remains stable or slows has not been reached. To ensure the sustainable development of the electric power industry, introducing higher energy efficiency standards for electrical appliances and improving income levels are vital. And government should emphasize electricity conservation in industrial sector rather than in residential sector.

Multifunctional landscapes are complex systems that integrate biophysical, cultural-historical and socio-economic components into unique territorial structures and regional ensembles. Facing increasing pressures generated by urbanization, climate change and overexploitation of natural resources, assessing the sustainability of these landscapes has become an urgent priority. The present research is based on the development and parametrization of a new tool for evaluating the sustainability of multifunctional landscapes that aims to measure the level of biocultural resilience of a landscape, integrating biological, cultural and socio-economic indicators in a single analytical framework. This index, called the biocultural resilience index (BRI), provides a holistic perspective on the dynamics of landscapes, allowing the identification of vulnerability areas and the development of conservation and sustainable management strategies. The evaluation of the of multifunctional landscapes sustainability requires a comprehensive approach that has to integrate both biological aspects, such as biodiversity and ecosystem health, as well as identity and cultural aspects, such as cultural value and the relationship of the local communities with the environment. In this context, this study highlights the fact that the development of appropriate tools and methods for assessing and monitoring the sustainability of multifunctional landscapes becomes essential for their sustainable management and for protecting the benefits they offer to society. Our findings show that the biocultural resilience index (BRI) can be used in a variety of contexts and fields, including spatial planning, biodiversity conservation, sustainable rural development and ecotourism. In the meanwhile, this index offers a robust and flexible analytical framework, adaptable to the needs and particularities of different regions and communities.

Background: Pediatric neurological disorders include neurodegenerative disease causing cognitive impairment, vision loss to mention a few. They are one of the important causes of morbidity and mortality in children with diverse etiology. Diagnosis is difficult in spite of genetic work and in only 60% of cases final diagnosis can be achieved. Case presentation: We explore three cases of pediatric neurological diseases, viz. Arthrogryposis, congenital bilateral cataract and Autism by analyzing clinical exomes. In this work, we attempted to understand rare neurological disorders in an Indian pediatric cohort using exome studies. Conclusions: We used our benchmarked CONVEX pipeline for screening consensus variants, wherein EIF2B2 was found to be inherently pathogenic. We map the association of variants and genes, disease correlation to neuroleptic malignant syndrome which is a matching phenotype to the cases.

Shape Memory Polymer (SMP) actuators are smart materials that adapt and switch shape in response to environmental conditions, allowing controlled and dynamic building systems. The integrated SMP strip enabled the adaptive facade shading system to operate independently and with flexibility under certain thermoresponsive conditions to regulate building performance. This study aims to improve adaptive façade performance in a hot-humid climate by determining optimal thermal activation factors for the shape memory polymer. This was achieved by comprehensively examining and analysing the impact of various SMP activation parameters on energy efficiency, thermal comfort, and visual comfort. In addition, dynamic IES-VE building energy simulation was used to evaluate the thermal performance of the adaptable facade. The results were validated using a multicriteria approach to compare with the existing glass façade of a high-rise apartment. The results showed that the coactivation technique, which combines solar radiation and air temperature triggers, proved to be the most efficient strategy to improve the performance of the adaptive façade. This strategy minimised heat gain, lowered indoor temperatures, reduced glare, and enhanced daylight comfort, resulting in notable energy savings through reduced cooling consumption. The study concluded that the utilisation of SMP actuators with fine-tuning activation parameters significantly optimised adaptive façade performance, promoting functionality, efficiency, and sustainability in buildings.

Hydrogels are used for various biomedical applications due to their biocompatibility, capacity to mimic the extracellular matrix, and ability to encapsulate and deliver cells and therapeutics. However, traditional hydrogels have a few shortcomings, especially regarding their physical properties, thereby limiting their broad applicability. Recently, researchers have investigated the incorporation of nanoparticles (NPs) into hydrogels to improve and add to the physical and biochemical properties of hydrogels. This brief review focuses on papers that describe the use of nanoparticles to improve more than one property of hydrogels. Such multifunctional hydrogel nanocomposites have enhanced potential for various applications, including tissue engineering, drug delivery, wound healing, bioprinting and biowearable devices.

Functional ZnO nanostructured surfaces are important in a wide range of applications. Here we report facile fabrication of ZnO surface structures at near room temperature with morphology resembling that of sea urchins, with densely packed, μm-long, tapered nanoneedles radiating from the urchin centre. The ZnO urchin structures were successfully formed on several different substrates with high surface density and coverage, including silicon (Si), glass, polydimethylsiloxane (PDMS), and copper (Cu) sheets, as well as Si seeded with ZnO nanocrystals. Time-resolved SEM revealed growth kinetics of the ZnO nanostructures on Si, capturing the emergence of “infant” urchins at the early growth stage and subsequent progressive increase in the urchin nanoneedle length and density, whilst the spiky nanoneedle morphology was retained throughout the growth. ε-Zn(OH)₂ orthorhombic crystals were also observed alongside the urchins. The crystal structures of the nanostructures at different growth time were confirmed by synchrotron X-ray diffraction measurements. On seeded Si substrates, a two-stage growth mechanism was identified, with a primary growth step of vertically aligned ZnO nanoneedle arrays preceding the secondary growth of the urchins atop the nanoneedle array. The antibacterial, anti-reflective, and wetting functionality of the ZnO urchins—with spiky nanoneedles and at high surface density—on Si substrates was demonstrated. First, bacteria colonisation was found to be suppressed on the surface after 24 h incubation in Gram-negative E. coli culture, in contrast to control substrates (bare Si and Si sputtered with 20 nm ZnO thin film). Secondly, the ZnO urchin surface, exhibiting superhydrophilic property with a water contact angle ~0°, could be rendered superhydrophobic with a simple silanization step, characterised by a water static contact angle θ of 159° ± 1.4° and contact angle hysteresis ∆θ < 7°. The dynamic superhydrophobicity of the surface was demonstrated by bouncing-off of a falling 10 μL water droplet, with a contact time of 15.3 milliseconds (ms), captured using a high-speed camera. Thirdly, it was shown that the presence of dense spiky ZnO nanoneedles and urchins on the seeded Si substrate exhibited a reflectance R < 1% over the wavelength range λ = 200–800 nm. The ZnO urchins with unique morphology via a facile fabrication route at room temperature, readily implementable on different substrates, may be further exploited for multifunctional surfaces and product formulations.

Leucokinins (LKs) constitute a neuropeptide family first discovered in a cockroach and later identified in numerous insects and several other invertebrates. The LK receptors are only distantly related to other known receptors. Among insects, there are many examples of species where genes encoding LKs and their receptors are absent. Furthermore, genomics has revealed that LK signaling is lacking in several of the invertebrate phyla and in vertebrates. In insects, the number and complexity of LK expressing neurons vary, from the simple pattern in the larva of Drosophila where the entire CNS has 20 neurons of three main types, to cockroaches with about 250 of many different types. Common to all studied insects is the presence or 1-3 pairs of LK-expressing neurosecretory cells in each abdominal neuromere of the ventral nerve cord, that, at least in some insects, regulate secretion in Malpighian tubules. This review summarizes the diverse functional roles of LK signaling in insects, as well as other arthropods and mollusks. These functions include regulation of ion and water homeostasis, feeding, sleep-metabolism interactions, state-dependent memory formation, as well as modulation of gustatory sensitivity and nociception. Other functions are implied by the neuronal distribution of LK, but remain to be investigated.

Fractional cointegration in time series data has been explored by several authors, but panel data applications have been largely neglected. A previous study of ours discovered that the Chen and Hurvich fractional cointegration test for time series was fairly robust to a moderate degree of heterogeneity across sections, out of the six tests considered. Therefore, this paper advances a customized version of the Chen and Hurvich methodology to detect cointegrating connections in panels with unobserved fixed effects. Specifically, we develop a test statistic that accommodates variation in the long-term cointegrating vectors and fractional cointegration parameters across observational units. The behaviour of our proposed test is examined through extensive Monte Carlo experiments under various data generating processes and circumstances. The findings reveal that our modified test performs quite well comparatively and can successfully identify fractional cointegrating relationships in panels even in the presence of idiosyncratic disturbances unique to each cross-sectional unit. Furthermore, the proposed modified test procedure established the presence of long-run equilibrium between the exchange rate and labour wage of 36 countries agricultural markets.

Aseptic implant loosening after total joint replacement is partially influenced by material-specific factors when cobalt-chromium alloys are used, including osteolysis induced by wear- and corrosion products, and stress shielding. Here, we aim to characterize a hybrid material consisting of alumina-toughened zirconia ceramics (ATZ) and additively manufactured Ti-35Nb-6Ta (TiNbTa), joined by a glass solder. The structure of the joint, static and fatigue shear strength, the influence of accelerated aging, and the cytotoxicity using an elution assay with human osteoblasts is characterized. Furthermore, the biomechanical properties of functional demonstrators of a femoral component for total knee replacements are evaluated. TiNbTa-ATZ specimens showed a homogenous joint with statistical distributed micro-pores and a slight accumulation of Al-rich compounds at the glass solder-TiNbTa interface. The static shear strength was 26.4 ± 4.2 MPa (Ti-ATZ reference: 38.2 ± 14.4 MPa, p = 0.117), all specimens survived 107 cycles of shear loading to 10 MPa, and aging did not reduce the strength. TiNbTa-ATZ did not impair the proliferation and metabolic activity of human osteoblasts. Functional demonstrators of TiNbTa-ATZ provided a maximum bearable extension-flexion moment of 40.7 ± 2.2 Nm. Biomechanical and biological properties of TiNbTa-ATZ demonstrate potential application for endoprosthetic implants.

Background: Circulating rare cells participate in breast cancer evolution as systemic components of the disease and thus, are a source of theranostic information. Exploration of cancer-associated rare cells is in its infancy. We determined the validity of a rare-cell detection platform and demonstrated the usefulness of a certain rare cell subset as a novel approach to characterize the breast cancer system. Methods: Linearity of the Rarmax® platform was established using a spike-in approach. The platform includes red blood cell lysis, leukocyte depletion and high-resolution fluorescence image recording. Rare cell analysis was conducted on 28 samples (before and after surgery) from 14 patients with breast cancer, 20 healthy volunteers and 9 non-cancer control volunteers. In-depth identification of rare cells, including circulating tumor cells, endothelial-like cells, erythroblasts and inflammation-associated cells, was performed using a phenotype and morphology-based classification system. Results: The platform performed linearly over a range of 5-950 spiked cells, with an average recovery of 84.6%. Circulating epithelial and endothelial-like cell subsets have been demonstrated to be associated with or independent of cancer with tumor presence. Furthermore, certain cell patterns may be associated with treatment-related adverse effects. The sensitivity in detecting tumor-presence and cancer-associated abnormality before surgery was 50% and 85.7%, respectively and the specificity was 100% and 96.6%, respectively. Conclusion: The present study supports the idea of a cancer-associated rare cell abnormality to represent tumor entities as well as systemic cancer. The latter is independent of the apparent clinical cancer.

Urbanization is considered as a main indicator of regional economic development due to its positive effect on promoting industrial development; however, many regions, especially developing countries, are troubled by its negative effect — the aggravating environmental pollution. Many researchers have indicated that rapid urbanization stimulated the expansion of industrial production scale and increased industrial pollutant emissions. However, this judgement contains a grave deficiency in that urbanization not only expands industrial production scales but can also increase industrial labour productivity and change the industrial structure. To modify this deficiency, we first decompose the influence which urbanization impacts on industrial pollutant emissions into the scale effect, the intensive effect and the structure effect by using the Kaya Identity and the LMDI Method; second, we perform an empirical study of the three effects’ impacts by applying the spatial panel model with data from 282 Chinese cities between 2003 and 2013. Our results indicate that (1) there are significant reverse U-shapes between Chinese urbanization rate and its industrial pollutant emissions; (2) the scale effect and the structure effect have aggravated Chinese industrial waste water discharge, sulphur dioxide emissions and soot (dust) emissions, while the intensive effect has generated a decreasing and ameliorative impact on that aggravated trend. The definite relationship between urbanization and industrial pollutant emissions depends on the combined influence of the scale effect, the intensive effect and the structure effect; (3) there are significant spatial autocorrelations of industrial pollutant emissions between Chinese cities, but the spatial spillover effect from other cities does not aggravate local urban industrial pollutant emissions, we offer an explanation to this contradiction that the vast rural areas surrounding Chinese cities have served as sponge belts and have absorbed the spatial spillover of cities’ industrial pollutant emissions. According to the results, we argue that this type of decomposition of the influence into three effects is necessary and meaningful, it establishes a solid foundation for understanding the relationship between urbanization and industrial pollutant emissions, and effectively helps to meet relative policy making.

Premature failure and degradation of layers are the main problems for transportation infrastruc-ture. Addressing these issues necessitates implementing structural health monitoring (SHM) for transportation layers. This strategic approach is instrumental in mitigating maintenance expenses, prolonging the operational lifespan, and preventing accidents resulting from abrupt layer col-lapse. To this end, this research investigated the stress/strain and damage detection capabilities of a self-sensing cementitious composite developed for potential utilization in the construction of an intelligent subgrade layer. The prepared self-sensing cementitious composite consisted of 10% cement and hybrid conductive fillers, including multiwalled carbon nanotubes (MWCNTs) and graphene nanoplatelets (GNPs) in sand. Initial findings reveal that the electrical resistivity of the composite is significantly affected by the concentration of MWCNTs/GNPs, with a minimum concentration of more than 0.5% needed to achieve a responsive cementitious composite. More-over, the piezoresistive analysis indicates that an increase in the concentration of MWCNTs/GNPs and stress levels leads to an improvement in the stress/strain sensing perfor-mance. When the self-sensing cementitious composite is subjected to equivalent stress levels, variations in the FCR exhibit an increasing trend with decreasing resilient modulus, stemming from a decrease in stiffness due to the increased concentration of MWCNTs/GNPs. Additionally, the EIS analysis demonstrates a contraction for the Nyquist curves under compressive ramp loading prior to failure, followed by the expansion of these curves postfailure. Scanning electron microscopy (SEM) images visually showcase the bridging effects of MWCNTs and the filling ef-fects of GNPs within the composite structure.

Asymptotic theories for fractional cointegrations have been extensively studied in the context of time series data, with numerous empirical studies and tests developed. However, most of the previously developed testing procedures for fractional cointegration were primarily designed for time series data. This paper proposes a generalized residual-based test for fractionally cointegrated panels with fixed effects. The test development is based on bivariate panel series with the regressor assumed to be fixed across cross-sectional units. The proposed test procedure accommodates any integration order between [0,1], and it is asymptotically normal under the null hypothesis. Monte Carlo experiments demonstrate that the test exhibits better size and power compared to a similar residual-based test across varying sample sizes.

Building facade design plays an essential role in enhancing energy efficiency and reducing environmental impact in high-performance building design. Balancing the conflicts among various building facade design parameters to satisfy different optimization objectives constitutes a highly complex optimization problem. The rapidly increasing number of studies demonstrates a significant interest in implementing multi-objective optimization methods to tackle building facade optimization problems. This study conducts a systematic review of optimization methods for building facade optimization (BFO). The optimization objectives and design variables are categorized based on their characteristics. The efficiency and effectiveness of optimization algorithms in addressing BFO problems are compared. Building optimization techniques and tools are showcased, along with their functions and limitations. Key findings highlight the robust feasibility and effectiveness of optimization algorithms, methods, and techniques in resolving a diverse range of BFO challenges. The limitations, challenges, and future potential of these methods are summarized and proposed.

Power quality is a major concern in electrical power systems. The power quality disturbances such as sags, swells, harmonic distortion and other interruptions have impact on the electrical devices and machines and in severe cases can cause serious damages. Therefore it is required to recognize and compensate all types of disturbances at an earliest to ensure normal and efficient operation of the power system. To solve these problems, many types of power devices are used. At the present time, one of those devices, Dynamic Voltage Restorer (DVR) is the most efficient and effective device used in power distribution system. In this paper, design and modeling of a new structure of multifunctional DVR for voltage correction is presented. The performance of the device under different conditions such as voltage swell, voltage sag due to symmetrical and unsymmetrical short circuit, starting of motors, and voltage distortion are described. Simulation result shows the superior capability of proposed DVR to improve power quality under different operating conditions. The proposed new DVR controller is able to detect the voltage disturbances and control the converter to inject appropriate voltages independently for each phase and compensate to load voltage through three single- phase transformers.

Europium (Eu)-doped fluorapatite (FA) nanorods has a similar biocompatibility with hydroxyapatite (HA) in terms, attracted much attention as cell imaging biomaterials due to their luminescent property. Here, we will discuss the new feature of europium doped fluorapatite (Eu-FA) nanorods as anticancer drug carrier. Eu-FA nanorods was prepared using a hydrothermal method. The morphology, crystal structure, fluorescence and composition are investigated. The specific crystal structure, enabling an effective loading of drug molecules. Doxorubicin (DOX), used as an anticancer model drug, was shown to be effectively loaded onto the surface of the nanorods. The DOX release was fairly pH-dependent, occurring more rapidly at pH 5.5 than pH 7.4 was observed. The intracellular penetration of the DOX-loaded Eu-FA nanorods (Eu-FA/DOX) can be imaged in situ due to the self-fluorescence property. Treatment of melanoma A375 cells with Eu-FA/DOX elicited a more effective apoptosis rate than direct DOX treatment. Overall, Eu-FA show great promise for tracking and treating tumor, may potentially useful as a multifunctional carrier system to effectively load and sustainably deliver drugs.

As prominent oil producers, the Gulf Cooperation Council (GCC) countries have played a significant role in the global energy market. However, as the world's attention increasingly shifts towards environmental sustainability, understanding the implications of the GCC's economic activities on CO2 emissions becomes indispensable. This research paper investigates the relationship between specific economic indicators and their impact on CO2 emissions in the GCC from 2001 to 2021. The study employs quantile regression, a powerful statistical method that estimates the conditional quantiles of a response variable given a set of predictor variables. The findings reveal several important insights: Financial institution efficiency is significant and negative at a 1% level at the lower (10th) -83537.3 and the higher quantile (90th) -549002.3. The relationship between GDP per capita and CO2 emissions varies across quantiles, highlighting the complexity of the growth-environment nexus. Total patents exhibit a positive and significant relationship with emissions, underscoring the importance of directing innovation towards environmentally sustainable solutions. Renewable energy consumption displays a nuanced relationship with CO2 emissions, with a stronger negative impact observed at higher consumption levels. This underscores the potential of renewable energy to mitigate emissions when integrated at scale. The study's outcomes hold crucial policy implications for the GCC countries as they seek to align economic growth with environmental sustainability. The findings emphasize the importance of fostering financial institution efficiency, promoting green innovation, and expanding renewable energy sources to reduce emissions

This study involved a comprehensive examination of sensory attributes in Bísaro dry-cured loins, including odor, androsterone, scatol, color, fat color, hardness, juiciness, chewiness, flavor intensity, and flavor persistence. Analysis of 40 samples revealed a wide variation in these attributes, ensuring a robust margin for multivariate calibration purposes. The respective near-infrared (NIR) spectra unveil distinct peaks associated with significant components such as protein, lipid, and water. Support Vector Regression (SVR) models were methodically calibrated for all sensory attributes, with optimal results using multiplicative scattering correction pre-treatment, MinMax normalization, and radial base kernel (non-linear SVR model). The predictive models exhibited acceptable results, characterized by R-squared values close to 1 (0.9616 - 0.9955) and low RMSE values (0.0400 – 0.1031). The prediction set's relative standard deviation (RSD) remained under 5%. Comparisons with prior research revealed significant improvements in prediction accuracy, particularly when considering attributes like pig aroma, hardness, fat color, and flavor intensity. This research underscores the potential of advanced analytical techniques to improve the precision of sensory evaluations in food quality assessment.

This paper contributes to the debate on the impact of economic diversity and the resource curse on economic growth. We use dynamic panel data models on data on Canadian and US sub-national jurisdictions. We find evidence for a positive relationship between diversity and growth. Based on the Krugman Specialization Index, our analysis shows that the required threshold for not having the resource curse is 0.209. Above this threshold, the marginal contribution of natural resources to economic growth is lower for a more diversified regional economy than a less diversified one. We highlight the policy implications of these findings.

Chen, et al., compared two modified polyurethane-based wound dressings (PUE and PUESi), both intended for use in chronic wounds, with a negative control (gauze) and a positive control (PolyMem) via a series of preliminary in vitro and rodent model tests. Future studies may find that one or both of these two new dressings are beneficial. However, the results of this first study cannot be relied upon. Although they exhibited in-depth knowledge of manufacturing techniques, the study designers seem far less familiar with the science of wound healing and with PolyMem wound dressings. This helps explain the flaws in the methods that lead to many of their tests not being translatable to real-world settings. In addition, the interpretation of some of the test results is questionable.

BMAP-18, derived from the N-terminal region of bovine myeloid antimicrobial peptide BMAP-27, demonstrated potent antimicrobial activity without cytotoxicity. This study aimed to compare the antibacterial, antibiofilm, and anti-inflammatory properties of BMAP-18, rich in aromatic phenylalanine residues, with its aliphatic analogue, BMAP-18-FL. Both aromatic BMAP-18 and aliphatic BMAP-18-FL exhibited equally potent antimicrobial activities against Gram-positive and Gram-negative bacteria, particularly methicillin-resistant Staphylococcus aureus (MRSA) and multidrug-resistant Pseudomonas aeruginosa (MDRPA). Mechanistic investigations employing SYTOX green uptake, DNA binding, and FACScan analysis revealed that both peptides acted by inducing membrane permeabilization and subsequent intracellular targeting. Moreover, both BMAP-18 and BMAP-18-FL effectively prevented biofilm formation and eradicated existing biofilms of MRSA and MDRPA. Notably, BMAP-18-FL displayed superior anti-inflammatory activity compared to BMAP-18, significantly reducing the expression levels of pro-inflammatory cytokines in lipopolysaccharide-stimulated macrophages. This study emphasizes the similarities and differences in the antimicrobial, antibiofilm, and anti-inflammatory properties between aromatic BMAP-18 and aliphatic BMAP-18-FL, providing valuable insights for the development of multifunctional antimicrobial peptides against drug-resistant bacteria.

Ferulic acid has numerous beneficial effects for human health, which are frequently attributed to its antioxidant behavior. In this report many of them are reviewed and 185 new ferulic acid derivatives are computationally designed, using the CADMA-Chem protocol. For the later, the chemical space was sampled and evaluated. To that purpose selection and elimination scores were used, which are built from a set of descriptors accounting for ADME properties, toxicity, and synthetic accessibility. After the first screening, 12 derivatives were selected and further investigated. Their potential role as antioxidants was predicted from reactivity indexes, directed related with the formal hydrogen atom transfer and the single electron transfer mechanisms. The best performing molecules were identified by comparisons with the parent molecule and two references: Trolox and alpha-tocopherol. Their potential as polygenic neuroprotectors was investigated through the interactions with enzymes directed related with the etiologies of Parkinson’s and Alzheimer’s diseases. They are acetylcholinesterase, catechol-O-methyltransferase, and monoamine oxidase B. Based on the obtained results, the most promising candidates (FA-26, FA-118, and FA-138) are proposed as multifunctional antioxidants with potential neuroprotective effects. The findings derived from this investigation are encouraging and might promote further investigations on these molecules.

The skin acts as a protective barrier, guarding the body against microorganisms, chemicals, and several environmental factors. Accordingly, this all-important organ must be kept healthy to maintain its optimal functionality. One approach to maintain skin health is the application of multifunction bioactive sunscreens containing antioxidant molecule(s). Rosmarinic acid (RA), a phenolic compound, is known for its antioxidant activity. Herein, the safety and efficacy of a multifunction prototype sunscreen were investigated, aiming to probe putative synergies of this polyphenol with two known and widely used UV filters (bemotrizinol and octyl p-methoxycinnamate). Samples protected the DNA fragmentation compared to UV control, by the comet assay, and showed good skin compatibility in subjects. Formulations F1 and F3 were able to increase skin hydration, and, possibly, the RA interfered with this attribute. An increase in transepidermal water loss was observed for formulations F1, F2 and F4, which may be related to vehicle containing or not the RA. No decreases were observed in the inflammatory reaction caused by the ethyl nicotinate with any of the evaluated formulations. As a perspective, we suggest trials with a greater number of subjects or protocol modifications. Altering the vehicle qualitative and quantitative composition is also a pertinent perspective.

Poly(vinylidene fluoride) nanocomposites processed with different morphologies, such as porous and non-porous films and fibres, have been prepared with silica nanoparticles (SiNPs) of varying diameter (17, 100, 160 and 300 nm) which in turn have encapsulated perylenediimide (PDI), a fluorescent molecule. Structural, morphological, optical, thermal, and mechanical properties of the nanocomposites, with SiNP filler concentration up to 16 wt% were evaluated. Further, cytotoxicity and cell proliferation studies were performed. All SiNPs are negatively charged independently of the pH and more stable from pH 5 upwards. The SiNPs introduction within the polymer matrix increases the contact angle independently of the nanoparticle diameters and the smallest ones (17 nm) improve the PVDF Young modulus from 0.94 ± 0.04 GPa for the pristine polymer film to 1.05 ± 0.06 GPa. Varying filler diameter, physico-chemical, thermal and mechanical properties of the polymer matrix were not significantly affected. Finally, the SiNPs inclusion does not induce cytotoxicity in murine myoblasts (C2C12) after 72 h of contact and proliferation studies reveal that the prepared composites represent a suitable platform for tissue engineering applications, as they allow to combine the biocompatibility and piezoelectricity of the polymer with the possible functionalization and drug encapsulation and release of the SiNP.

This study describes an eco-friendly synthesis of ZnO nanoparticles using aqueous oat extract. The advanced electrochemical and optical features of green synthesized ZnONPs displayed excellent antibacterial activity, and exhibited an important role in pharmaceutical determinations. The formation of nanoscale ZnO was confirmed using various spectroscopic and microscopic investigations. The formed nanoparticles were found to be around 100 nm. The as-prepared ZnONPs were monitored for their antibacterial potential against different bacterial strains. The inhibition zones for ZnONPs were found as E. coli (16 mm), P. aeruginosa (17 mm), S. aureus (12 mm) and B. subtilis (11 mm) using 30 µg mL-1 sample concentration. Also, ZnONPs exhibited significant antioxidant effects 58 to 67 % with an average IC50 value of 0.88 ± 0.03 scavenging activity and 53 to 71 % (IC50 value 0.73 ± 0.05) against the DPPH and ABTS scavenging free radicals, respectively. The photocatalytic potential of ZnONPs for Rhodamine B dye degradation dye under UV irradiation was performed. The photodegradation process was carried out as a function of time-dependent and the complete degradation (nearly 98 %) with color removal after 120 min. Conclusively, the synthesized ZnONPs using oat biomass might provide a great promise in the future for biomedical applications.

ABSTRACT Surfactants are a broad category of tensio-active biomolecules with multifunctional properties applications in diverse industrial sectors and processes. Surfactants are produced synthetically and biologically. The biologically derived surfactants (biosurfactants) are produced from microorganisms with Pseudomonas aeruginosa, Bacillus subtilis Candida albicans and Acinetobacter calcoaceticus as dominant species. Rhamnolipids, sophorolipids, mannosylerithritol lipids, surfactin, and emulsan are well known in terms of their biotechnological applications. Biosurfactants can compete with the synthetic surfactants in terms of performance with established advantages over the synthetic ones including eco-friendliness, biodegradability, low toxicity, and stability over a wide variability of environmental factors. However, at present, the synthetic surfactants are a preferred option in different industrial applications, because of their availability in commercial quantities, unlike the biosurfactants. Usage of synthetic surfactants introduce new species of recalcitrant pollutants to the environment and lead to undesired results where a wrong selection of surfactants is made. Substituting synthetic surfactants with biosurfactants resolves these drawbacks, thus, interest has been intensified in biosurfactant applications in a wide range of industries hitherto considered as experimental fields. This review, therefore, intends to offer an overview of diverse applications where biosurfactants have found useful, with emphases in petroleum biotechnology, environmental remediation and in the agriculture sector. Application of biosurfactant in these settings would lead to industrial growth and environmental sustainability.

This study aims to provide empirical evidence on whether using renewable and non-renewable energy, CO₂ emissions and the resulting changes in temperature and precipitation can alter cereal yields in European Union countries. To this end, a panel data set covering 1992-2021 has been used to analyse the impact of climate change and economic factors on cereal production in European Union countries. The study employed various analytical techniques to understand better the relationship between climate change, energy consumption, and economic growth. These included using annual average temperature and rainfall to measure climate change and energy consumption and economic growth to analyse the economic aspects. To achieve the objective, feasible generalised least squares (FGLS) models with robust standard errors and bootstrap and a quantile regression (QR) model with marginal analysis were employed. The Westerlund cointegration test confirmed the presence of cointegration between cereal production and climate variables, economic growth, and energy consumption. The results indicate that increases in temperature and precipitation may contribute to increased cereal production in European Union countries. In contrast, energy consumption, including renewable energy and CO₂ emissions, may have a nonlinear effect on cereal production. Quantile regression analysis suggests climate change may impact crop yields most in countries with low and moderate cereal production per hectare. Increased CO₂ emissions may increase yields in the initial period, but excessive CO₂ may negatively impact cereal production in the long term. It would be advisable for countries with low and moderate crop productivity to consider implementing technological advances and combating global warming by modernising cultivation methods and making greater use of renewable energy sources.

Hereditary cancer syndromes caused by germline mutations account for 5-10% of all cancers. The finding of a genetic mutation could have far-reaching consequences for pharmaceutical therapy, personalized prevention strategies, and cascade testing. According to the National Comprehensive Cancer Network’s (NCCN) and the Italian Association of Medical Oncology (AIOM) guidelines, unaffected family members should be tested only if the affected one is unavailable. This article explores whether germline genetic testing may be offered to high-risk families for hereditary cancer even if a living affected relative is missing. A retrospective study was carried out on 103 healthy subjects tested from 2017 to 2023. We enrolled all subjects with at least two first or second-degree relatives affected by breast, ovarian, pancreatic, gastric, prostate, or colorectal cancer. All subjects were tested by Next Generation Sequencing (NGS) multi-gene panel of 27 cancer-associated genes. In the study population, 5 (about 5%) pathogenic/likely pathogenic variants (PVs/LPVs) were found while 40 (42%) had a Variant of Uncertain Significance (VUS). This study highlights the importance of genetic testing for individuals with a strong family history of hereditary malignancies. This approach would allow women who tested positive to receive tailored treatment and prevention strategies based on their personal mutation status.

Gold nanoclusters (AuNCs) with fluorescence in the Near Infrared (NIR) by both one- and two-photon electronic excitation were incorporated in mesoporous silica nanoparticles (MSNs) using a novel one-pot synthesis procedure where the condensation polymerization of alkoxysilane monomers in the presence of the AuNCs and a surfactant produce hybrid MSNs of 49 nm diameter. This method was further developed to prepare 30 nm diameter nanocomposite particles with simultaneous NIR fluorescence and superparamagnetic properties, with a core composed of superparamagnetic manganese ferrite nanoparticles (MnFe2O4) coated with a thin silica layer, and a shell of mesoporous silica decorated with AuNCs. The nanocomposite particles feature NIR-photoluminescence with 0.6% quantum yield and large Stokes shift (290 nm), and superparamagnetic response at 300 K, with a saturation magnetization of 13.4 emu g-1. The conjugation of NIR photoluminescence and superparamagnetic properties in the biocompatible nanocomposite has high potential for application in multimodal bioimaging.

People counting applications have been used in diverse applications. The ability and accuracy of thermal imaging over conventional image cameras has led to the implementation of thermal cameras in people counting applications. This paper present a thermal people counting smart glass windows. The people counting application would be remotely monitored from a single centralized PC station as it’s connected to a multiplex of mass monitoring of 20 thermal camera, all embedded into different glass windows. The thermal cameras would then be able to detect body temperatures of all individuals who pass through any of the camera range and also count the numbers of people who passed through the camera range. The data gotten can then be further utilized in various ways, example is in the control of air conditioning and lightening.

The objective of the proposal is to find the optimal geometric shape of a photovoltaic panel that maximizes the collection of solar radiation. The optimal shape will be determined based on direct radiation, as it is the most relevant radiation for the photovoltaic process. To achieve this goal, we will use computer simulations to evaluate the performance of different geometric shapes under different conditions of solar radiation. Specifically, we will simulate the behavior of a photovoltaic panel with different shapes and orientations, and we will compare their energy yield over a given period of time. The simulations will be based on a mathematical model that takes into account the incidence angle of solar radiation on the panel, as well as other factors such as the reflection and absorption of radiation, and the temperature of the panel. The simulations will be carried out for different locations, with different solar radiation conditions, and for different periods of time, in order to obtain a comprehensive assessment of the performance of the different shapes. The results of the simulations will be analyzed to identify the optimal shape of the photovoltaic panel. This shape will be compared with the performance of flat panels, both static and with tracking systems, in order to evaluate the potential improvement in energy yield.

The direct hydrogenation of greenhouse gas carbon dioxide (CO2) to higher alcohols (C2+OH), as an important research area in C1 chemistry, is one of the most essential approaches to convert CO2 into liquid fuels or other value-added chemicals. The high atom economy and direct pathway make this reaction attractive to convert CO2 to higher alcohols. However, due to the complicated reaction network and the difficulty of C-C coupling, the formation of higher alcohols is more difficult compared with methanol or other compounds containing one carbon. The key issue is development of novel catalysts with high conversion and space time yield. But this is still a huge challenge faced by researchers. In this review, the thermodynamics and reaction pathways of CO2 hydrogenation were firstly clarified. Subsequently, after reviewing single metal-based, bi-and multi-metallic catalysts, the recently progress of tandem catalytic system was emphasized. Finally, we also provided an overview about tandem catalysis for CO2 hydrogenation to higher alcohols.

Developing low-cost and stable materials for converting solar energy into electricity is vital in meeting the world's energy demand. Metal-organic frameworks (MOFs) have gained attention for solar cells due to their natural porous architectures and tunable chemical structures. This review commences with an exploration of the synthetic methods of MOFs. Moreover, we discuss the various roles of MOFs, including photoanodes and counter electrodes in dye-sensitized solar cells and interfacial layers and charge carriers in perovskite solar cells. Ultimately, burdensome tasks and possible directions for advancing MOFs-based nanomaterials are provided for solar cells.

In order to improve the strength of PVA/xylan composite films and endow them with ultraviolet (UV) shielding ability, TiO2-KH550 nanoparticle was synthesized and added into the PVA/xylan matrix. The TiO2-KH550 nanoparticle dispersed well in the 0.04% sodium hexametaphosphate (SHMP) solution under ultrasonic and stirring treatments. Investigations on the properties of films showed that TiO2-KH550 had the positive impact on improving the strength, moisture and oxygen barrier properties of the composite films. The maximum tensile strength (27.3 MPa), the minimum water vapor permeability (2.75×10-11 g•m-1•s-1•Pa-1) and oxygen permeability (4.013 cm3•m-2•24h-1•0.1MPa-1) were obtained under the addition of 1.5% TiO2-KH550. The tensile strength of TiO2-KH550 reinforced composite film was increased by 70% than that of the pure PVA/xylan composite film, and the water vapor and oxygen permeability were decreased by 31% and 41%, respectively. Moreover, the UV transmittance of film at the wavelength of 400 nm was almost zero when adding 1.5~2.5% of TiO2-KH550, which indicated the PVA/xylan composite films were endowed with excellent UV light shielding ability.

Halloysite nanotubes (HNTs) are natural occurring mineral clay nanotubes that have excellent application potential in different fields. However, HNTs are heterogeneous in size, surface charge and formation of surfacial hydrogen bond, which lead to weak affinity and aggregation at a certain extent. It is very important to modify the HNTs’ surface to expand its applications. In this review, the structural characteristics, performance and the related applications of surface-modified HNTs are reviewed. We focus on the surface-modified variation of HNTs, the effects of surface modification on the materials and related applications in various regions. In addition, future prospects and the meaning of surface modification were also discussed in HNTs studies. This review provides a reference for the application of HNTs modifications in the field of new nanomaterials.

Background: The cumulative exposure of UV radiation can result in dangerous consequences such as skin burns, photoaging, and skin cancer, hence the importance of using photoprotective formulations. Currently, the formulations seek to be more efficient, innovative and reach a wider audience. Many sunscreens are vegan, and have antioxidant substances to ensure additional photochemoprotective action. To evaluate biological, functional, and mechanical characteristics of them on the skin, biometric and rheologic methods can be used. Objective: Evaluate biophysical, rheological and sensorial parameters of Face Care Facial Moisturizing Cream® (P1) and a vegan formulation (P2) by in vitro and in vivo tests. Methods: A UV scan experiment was performed covering the range of 250 to 400 nm. Sun Protection Factor (SPF) was evaluated by Mansur method. Rheological profiles were obtained using a MARS II (Haake®) controlled shear stress and gradient rheometer. Biophysical parameters were analyzed: skin sebum content, hydration level, transepidermal water loss, erythema and melanin level, skin color, and skin pH. The acceptance profile of the formulations by the volunteers was determined using a 9-point hedonic scale and a 5-point purchase intention test. Results: The formulations effectively absorbed light covering the UV radiation spectrum from UVA to UVB. The SPF of P1 was 25.21 and of P2 was 12.10 by in vitro tests. They had also pseudoplastic and thixotropic behavior, it can contribute to better spreadability and to form a protective film. Biometric tests showed an increase in hydration and skin sebum, decreased erythema, and maintenance of skin pH after application of both formulations. The products also had similarly good acceptance and purchase intention by the volunteers. Conclusion: The comparation of a commercialized product and a vegan test version showed very similar rheological and great acceptance profiles. Therefore, the vegan formulation is a good alternative to reach a different market.

This paper investigates the relationship between public debt and economic growth in the context of a panel kink regression with latent group structures. The proposed model allows us to explore the heterogeneous threshold effects of public debt on economic growth based on unknown group patterns. We propose a least squares estimator and demonstrate the consistency of estimating group structures. The finite sample performance of the proposed estimator is evaluated by simulations. Our findings reveal that the nonlinear relationship between public debt and economic growth is characterized by a heterogeneous threshold level, which varies among different groups, and highlight that the mixed results found in previous studies may stem from the assumption of a homogeneous threshold effect.

With the development of society and the economy, the unified planning of architectural style has become a difficult problem in the competition between urban expansion and the protection of tra-ditional buildings in villages and towns. At the same time, it also allows people to re-examine the appearance and quality of life of traditional village buildings. In this paper, the Conditional Gen-erative Adversarial Network (CGAN) is used to construct a method of building facade generation in villages and towns, so as to gradually realize the governance of the style of villages and towns. At the same time, it has also reduced the restoration of the facades of villages and towns and the graphic design of rural tourism products, showing its application value and potential in the field of planning and design. In the research, taking villages and towns in the Wuyishan area of China as an example, the method is used to carry out model training, image generation, and comparison of the derivation results of different assumed building contours and product contours. The research shows that: (1) CGAN can be used to derive and design the facades of conventional civil buildings in villages and towns. (2) In terms of product graphic design, especially the common tourist cultural products fans and water cups, show significant potential. (3) The construction of this method is not only applicable to villages and towns under the World Heritage City, but can be further promoted and used in the future for cities and villages that have a demand for architectural style consistency.

Amidst the strong demand for wood-based products, and the clamor of environmental consciousness, more functional and green solutions arise to meet both of these goals. Pursuant to this, the study looked into the potential of a bio-waste taken from Cocos nucifera tree known as phellem—the tree’s outermost skin made of dead tissues, to be a main component of a new construction material. This study builds on existing research showing phellem is impermeable, buoyant, elastic, has a slow burn rate, and repels water during precipitation, which supports the hypothesis that phellem may be a potential substitute material for dry wall boards. To test this, three (3) formulations were developed as experimental setups to test the physico-mechanical properties of coconut palm phellem (COPAP): Formulation A (40% COPAP and 60% cement); Formulation B ( 25% COPAP and 75% cement); and lastly, Formulation C that was (10% COPAP and 90% cement). The study tested (1) which among these formulations exhibited the best physico-mechanical properties, then it (2) compared the formulations with common dry wall products available in the market, and subsequently, (3) identified the possible architectural applications of COPAP board as a new building material. Of the three setups, Formulation C exhibited the best physico-mechanical properties in terms of compressive and flexural strength, fire resistivity, and water absorption. It fared better than the particle board in terms of compressive strength, better than wafer and particle board in fire resistivity, performed best in the water absorption test, and was almost equivalent in flexural strength to fiber cement board. With these findings, the study concluded that COPAP board can be used for projects that entail a high number of interior partitions, such as offices, BPO firms and commercial stalls in shopping malls, etc. The findings were conclusive only for interior applications, as the results clearly suggest that the COPAP boards are not load-bearing. Future investigations may explore and assess other properties of COPAP boards like thermal and sound insulation, resistance to rot and other properties that may prove its competitive advantage as a construction material.

This study assesses the impact of globalization on female participation in the labor force (FPLF). The increased globalization in the last several decades has created various economic opportunities for enterprises and individuals worldwide at an unprecedented rate. As a result, it has helped improve the quality of life for many men and women. In this process, the issue of women’s economic participation has been a critical topic for discussion worldwide. In that context, the objective of the paper is to determine if FPLF is influenced by a country’s participation in foreign markets through foreign direct investment (FDI) – a proxy for globalization. The paper uses a panel dataset obtained from the World Bank’s World Development Indicators database for 99 countries from 2001 to 2018. We then use system Generalized Method of Moments (system GMM) to estimate a dynamic panel model with appropriate specification tests. The results show that the positive effects of FDI on FPLF are more robust for low- and middle-income countries than high-income countries. We also find that results may be sensitive to outlier observations. Our results explain the seemingly inconclusive results within existing literatures and suggest that low- and middle-income countries should particularly focus on sectors that generate FDI as they stand to yield the greatest benefits with regards to female economic empowerment.

In the aerospace sector, structural and non-structural components are usually subjected to a wide range of environmental conditions. Although lightweight, the use of composite parts for these applications is restricted, due to their poor performance in severe environmental conditions. Specifically, moisture can seriously damage the materials' performance, reducing their mechan-ical, thermal, electrical, and physical properties as well as the service time. A strategy to improve the materials’ resistance in humid environments is the use of protective lightweight barrier coatings to reduce the diffusion of gases and/or liquids in composites. Nanolamellar nanocom-posite characterized by the high in-plane orientation of nanoplatelets effectively works as barrier structures by generating tortuous paths for molecule diffusion. In this work, the effectiveness of protection against water uptake of nanocomposites reinforced with Graphite NanoPlatelets (GNPs) at high filler content (70, 80 and 90%wt) for Kevlar sandwich panels of a nacelle engine of an ATR42 aircraft has been investigated. Moisture uptake and Ground Air Ground (GAG) tests were carried out in an environmental chamber to reproduce temperature and relative humidity profiles representative of a real-scale application for a regional aircraft composite part. The high filler content of the graphene films ensures a high level of tortuosity by delaying and reducing moisture absorption by –71% compared to the unprotected panel, showing good barrier properties.

Serine/threonine kinase (AKT) signaling regulates diverse cellular processes and is one of the most important aberrant cell survival mechanisms associated with tumorigenesis, metastasis, and chemoresistance. Targeting AKT has become an effective therapeutic strategy for the treatment of many cancers. AKT3 (PKBγ), the least studied isoform of the AKT family, has emerged as a major contributor to malignancy. AKT3 is frequently overexpressed in human cancers, and many regulatory oncogenic or tumor suppressor small non-coding RNAs (ncRNAs), including microRNAs (miRNAs), have recently been identified to be involved in regulating AKT3 expression. Therefore, a better understanding of regulatory miRNA/AKT3 networks may reveal novel biomarkers for diagnosis of patients with cancer and provide invaluable information for developing more effective therapeutic strategies. The aim of this review is to summarize current research progress in the isoform-specific functions of AKT3 in human cancers and the roles of dysregulated miRNA/AKT3 in specific types of human cancers.

This paper presents a multifunctional reflective digital metasurface of arbitrary base based on voltage tunable liquid crystal (LC). The reflective digital metamaterial can be multiplexed for different desirable functions by properly biasing the LC for different code patterns. Simulation results of three significant functions, beam steering with a steering elevation angle 27° at 75 GHz, RCS reduction of at least 15dB along the incident direction, and beam shaping with different beam shapes have been presented to prove the concept.

The demand for sustainable cosmetics leads to the search for natural and biotechnology ingredients. The present study reports the development of multifunctional lip moisturizer containing levan (LEV) from Bacillus subtilis natto, sophorolipids (SOP) from Starmerella bombicola and Citrus paradisi (OCP) essential oil , using simplex-centroid experimental design. The formulations were evaluated physicochemically, pharmacotechnically and by DPPH assay. The optimized formulation was selected through Response Surface Method and the evaluation of its efficiency in lip hydration was carried out using bioimpedance method and sensory analysis. The formulations showed pH compatible with the lip region and remained stable after centrifuge test and thermal stress in preliminary stability. Spreadability varied between 415.3 and 1217.1 mm2, moisture retention was above 95%, and antioxidant capacity was around 50% for all formulations. The optimized formulation, containing 0.4% LEV and 0.8% SOF, helped to maintain the lip hydration already shown by the participants; 85% of them reported improvement in this aspect. The incorporation of these actives is innovative and helps in the development of future works, through the use of a new non-invasive and low-cost technique, not previously described in other studies, in association with relevant sensory analyzes in the field of cosmetology.

In this paper, the validity of the Wagner’s law is investigated in tenth selected Sub- Saharan African countries, namely Botswana, Equatorial Guinea, Mauritania, Nigeria, South Africa, Sierra Leone, Tanzania, Ethiopia, Madagascar, and DR Congo. Five variants of the Wagner’s law were tested for the period 2005-2014, using panel econometric approaches encompassing cointegration and causality. The study found a long run relationship between the public expenditure and the various explanatory variables used as proxies of income. The long-run causality tests indicate that there is bidirectional causality between expenditure and income in all models with the exemption of the Gupta model. It is concluded that for Sub-Saharan Africa, both the Wagner’s law the Keynesian hypothesis tend to be valid under the period of investigation. The explanation is that there has been the tendency for public expenditure to grow relative to national income (Wagner’s law) and that public expenditure is a policy instrument (an exogenous factor) for improving national income (Keynesian hypothesis) during the 10-year period.

Novel far-red-sensitive symmetric squaraine (SQ) dyes with terminal alkyl-chain modifications were designed, synthesized and characterized aiming towards imparting multifunctionalities such as photosensitization, dye aggregation prevention and source of electrolyte components. The dye sensitizers SQ-77 and SQ-80 with the alkyl chain terminal modifications consisting of iodine and 1-methylimidazolium iodide, respectively, were designed and synthesized as new dye sensitizers for DSSCs based on the symmetric SQ-5 without any terminal modification used as reference. Upon adsorption on the mesoporous TiO2 surface, The SQ-77 depicted an enhanced dye loading and dye aggregation. On the other hand, SQ-80 demonstrated reduced dye aggregation and stronger binding on the TiO2 surface leading to enhanced durability of DSSCs. Apart from the most common photosensitization behaviour, the newly designed dye demonstrated multifunctionality such as aggregation prevention and electrolyte functionality utilizing iodine-based redox electrolyte in the presence and absence of I2 and LiI additives. In the absence of LiI and I2, a mixture of SQ-77 and SQ-80 demonstrated a photoconversion efficiency of 1.54 % under simulated solar irradiation, which was about 6 times higher as compared to reference dye SQ-5 (0.24 %) having no alkyl chai terminal modification.

This study assesses the impact of militarization, industrialization, technological innovation, and energy consumption on CO2 emissions in NATO countries, divided into "traditional" (Group 1) and "new member" states (Group 2), using data from 1985 to 2019. It identifies heterogeneity in effects and dependencies between the groups. Employing Pedroni and Kao panel cointegration tests, a long-term equilibrium relationship among the variables is confirmed. The analysis, using panel ARDL and GMM methods, reveals distinct outcomes for each group. In Group 1, military spending and energy consumption significantly increase CO2 emissions, while industrialization and technological innovation reduce them. Conversely, in Group 2, technological innovation and energy consumption raise emissions, whereas military spending and industrialization decrease them. The findings suggest Group 1 should strategize military expenditure and energy consumption to cut emissions, whereas Group 2 should focus on eco-friendly technology and efficient energy use to achieve environmental sustainability.

The coronavirus disease (COVID-19) vaccine is key to reducing the probability of contracting COVID-19. The vaccine is generally known to prevent severe illness, death, and hospitalization as a result of the disease and for considerably reducing COVID-19 infection risk. Accordingly, this might significantly change an individual’s perceived risk of altering everyday behaviors. For instance, the proliferation of vaccination is anticipated to reduce preventive behaviors such as staying at home, handwashing, and wearing a mask. We corresponded with the same individuals monthly for 18 months from March 2020 (early stage of COVID-19) to September 2021 in Japan to independently construct large sample panel data (N=54,007), with a participation rate of 54.7 %. We used a fixed effects model, controlling for key confounders, to determine whether vaccination was associated with a change in preventive behaviors. The major findings are as follows. Contrary to the prediction, (1) based on the whole sample, being vaccinated against COVID-19 led people to stay at home; however, it did not change the habit of handwashing and wearing a mask. Especially after the second shot, respondents were likelier to stay at home by 0.107 (95% CIs: 0.059–0.154) points on a 5-point scale compared to before the vaccination. Dividing the entire sample into young and old, (2) those aged ≤ 40 years were more likely to go out after being vaccinated, and (3) people over 40 years of age were more likely to stay at home (similar to the first result). Preventive behaviors impact all individuals during the current pandemic. Informal social norms motivate people to increase or maintain preventive behaviors even after being vaccinated in societies where these behaviors are not enforced.

Studies employing Arellano-Bond and Blundell-Bond GMM estimation for single linear dynamic panel data models are growing exponentially in number. However, for researchers it is hard to make a reasoned choice between many different possible implementations of these estimators and associated tests. By simulation the effects are examined of many options regarding: (i) reducing, extending or modifying the set of instruments; (ii) specifying the weighting matrix in relation to the type of heteroskedasticity; (iii) using (robustified) 1-step or (corrected) 2-step variance estimators; (iv) employing 1-step or 2-step residuals in Sargan-Hansen overall or incremental overidentification restrictions tests. This is all done for models in which some regressors may be either strictly exogenous, predetermined or endogenous. Surprisingly, particular asymptotically optimal and relatively robust weighting matrices are found to be superior in finite samples to ostensibly more appropriate versions. Most of the variants of tests for overidentification restrictions show serious deficiencies. A recently developed modification of GMM is found to have great potential when the cross-sectional heteroskedasticity is pronounced and the time-series dimension of the sample not too small. Finally all techniques are employed to actual data and lead to some profound insights.

Background: Acute ischemic stroke is among the main causes of mortality worldwide; a rapid and opportune diagnosis is crucial to improve a patient's outcome. MicroRNAs are quite useful for a rapid and accurate diagnosis.Methods: We perform both structural networks approach and a meta-analysis (using a random-effect model to evaluate the heterogeneity and risk bias, according to the PRISMA statement) to analyze the feasibility to develop a microRNA-based biomarker panel for an opportune AIS diagnosis. Results: Structural networks identify a set of eight miRNAs (miR-16, miR-124-3p, miR-484, miR-15a, miR-4454, miR-107, miR-125b-5p and miR-320b) as preliminary microRNA-based biomarker panel, from these only three microRNAs are significantly associated with the main risk factors of AIS, (miR-107: hypertension, 95% CI 9.74-53.24 p<0.0001, type 2 Diabetes mellitus, 95% CI 2.18-19.26); p=0.0008; miR-16 hypertension, 95% CI 1.26-3.56 p=0.0046, smoking, 95% CI 1.07-3.54 p=0.0277; and miR-15a hypertension, 95% CI 1.26-3.56 p=0.0046; smoking, 95% CI 1.07-3.54 p=0.0277). However, the meta-analysis reveals that data is highly heterogeneous and biased; and only microRNAs isolated from plasma samples and further processed in microarrays are the most reliable to distinguish AIS patients.Conclusions: Together our results show that although there are some miRNAs that seem to be associated with AIS, we are still far to develop a miRNA-based biomarker for AIS diagnosis and it is necessary to harmonize the protocols, results and include more populations for further studies otherwise we will remain throwing punches in the dark.

Novel multifunctional fluorescent chemosensors composed of electrospun (ES) nanofibers with high sensitivity toward pH, mercury ions (Hg²⁺), and temperature were prepared from poly(N-Isopropylacrylamide-co-N-methylolacrylamide-co-rhodamine derivative) (poly(NIPAAm-co-NMA-co-RhBN2AM)) by employing electrospinning process. NIPAAm and NMA moieties provide hydrophilic and thermo-responsive properties (absorption of Hg²⁺ in aqueous solutions), and chemical cross-linking sites (stabilization of the fibrous structure in aqueous solutions), respectively. The fluorescent probe, RhBN2AM is highly sensitive toward pH and Hg²⁺. Synthesis of poly(NIPAAm-co-NMA-co-RhBN2AM) with different compositions were carried on via free-radical polymerization. ES nanofibers prepared from sensory copolymers with a 71.1:28.4:0.5 NIPAAm: NMA: RhBN2AM ratio (P3 ES nanofibers) exhibited significant color change from nonfluorescent to red fluorescence while sensing pH or Hg²⁺, and high reversibility of on/off switchable fluorescence emission when Hg²⁺ and ethylenediaminetetraacetic acid (EDTA) were sequentially added. The P3 ES nanofibrous membranes had a higher surface-to-volume ratio to enhance their performance than did the corresponding thin films. In addition, the fluorescence emission of P3 ES nanofibrous membranes exhibited second enhancement above the lower critical solution temperature. Thus, the ES nanofibrous membranes prepared from P3 with on/off switchable capacity and thermo-responsive characteristics can be used as multifunctional sensory devise for specific heavy transition metal (HTM) in aqueous solutions.

Green Infrastructures (GI) are considered key to reconcile ecological and social benefits by providing multiple functions. The concept is increasingly promoted and guidelines for its implementation have been developed in many countries and regions of the Western Hemisphere. However, for other parts of the world, especially for countries with less developed infrastructures, promotion, guidance for decision-making and manuals for GI are often lacking. But the state of infrastructure development and often unplanned character of settlements in the Global South differ and result in specific constraints as well as demands to GI that need to be addressed explicitly. This study presents a methodological approach to explicitly address the specific conditions and physical limitations to GI development in urban areas of the Global South. A four step methodology was developed to assess the implementation potential for retrofitted and multifunctional urban green infrastructure in public areas. An initial site analysis (1) and the definition of design criteria as well as general strategies (2) to achieve the different dimensions of multi-functionality are the basis to derive spatial typologies (3) for GI elements and finally the spatial suitability assessment for potential placements (4). An application of the methodology to a study area in the metropolitan region of San José, Costa Rica, shows exemplarily that the potential to improve the hydrological conditions (up to 34% of surface runoff reduction), ecological conditions (increase of green space by 2,2 %, creation of 1500 m length of roadside greenery and two new habitat types), and social conditions (2.200 m of road type upgrading) of multi-functionality of the site through Green Infrastructures. These assessment results of different multi-functionality dimension can serve as a guidance for GI promotion and implementation in urban areas of the Global South.

Here, we present a series of novel block copolymers (BCP) from bio-derived monomers, poly(lactic acid)-block-poly(2,5-furandimethylene succinate) (PLA-b-PFS), in which the furan groups from PFS block can be crosslinked with bis(maleimido) triethylene glycol (M2) through a Diels-Alder reaction. This dynamic crosslinking reaction leads to a network structure for enhancing the mechanical properties compared to their linear BCP analogous. Decreasing the crosslinking density leads to a decrease of glass transition temperature of BCPs and a transition from glassy to rubbery-like behavior at room temperature. This allows a wide tunablity of both elastic moduli and yields of the materials. For the lowest crosslinking density. the material exhibits an over 50% self-healing efficiency at room temperature after five days, attributed to the low Tg (15.2 C) from the introduction of PFS block, allowing sufficient chain mobility for structure re-organization. Moreover, with the appropriate selection of crosslinking density (PLA-b-PFS/M2 (6/1)), it also shows an excellent shape memory property with a high recovery rate of 96.3% and a fixity rate of 97.3%. The permanent shape can be rewriteable due to the reversibility of Diels-Alder reaction. With these advanced functionalities and ease in large-scale fabrication, the PLA-b-PFS/M2 shows great promises for self-healing coatings or films with shape memory properties in a wide variety of applications such as packaging materials

Respiratory tract infections (RTIs) are one of the main causes of hospitalization and mortality causing substantial economic burden to healthcare systems globally. As opposed to the previous belief that respiratory infections are caused by a single pathogen, studies have shown that most RTIs are a result of a combination of bacterial and/or viral pathogens infecting the host. The clinical manifestation of RTIs is very similar (i.e., syndrome), often showing Influenza-like illness (ILI) symptoms. While COVID-19 has dominated ILI over the past few years, there are many other pathogens that are responsible for ILI. In addition, it is not uncommon to have coinfections with multiple pathogens in patients presenting with ILI and that such coinfections can even exacerbate the disease severity of RTIs. Therefore, an insight into coinfections can help with accurate disease prognosis, patient care management and outcomes. The goal of this study was to identify the different organisms in symptomatic patients presenting with ILI.

The paper presents modelling of relationships between wind velocity distributions observed in Poland and technical requirements for wind power stations design. The wind velocities distributions for various locations in Poland are determined, and expressed in Weibull distribution parameters. Theoretical computations concerning the dependence of wind power station as function of wind speed and aire physical properties are presented. Conclusions important for design of power stations fitted to atmospheric conditions in Poland are given. Wind power plants have been an important source of electricity generation for many years.Wind power modelling with the use of wind speed is used to improve the accuracy of forecasts and analyses of the power production of wind farms.

Purpose: The aim of the study is an approach to a nanocomposite with copper nanoparticles, constituting a bacteriostatic surface for maintaining the human lung cells' function. Methods: The polyelectrolyte layer coating with copper nanoparticles incorporated was designed. As a bacteriostatic factor, copper nanoparticles were applied as a colloidal solution of copper nanoparticles (ColloidCuNPs) and solution of copper nanoparticles (CuNPs). The influence of polyelectrolytes on selected Gram(+) and Gram(-) strains was examined. The function of the human adenocarcinoma A549 cell line of epithelial human lung cells cultured in the presence of nanocomposite layer coatings was analyzed, as well as their morphology using flow cytometry, fluorescence microscopy, and scanning electron microscopy. In addition, the material of layer coating was assessed using AFM and SEM-EDX characterization. Results: It was observed that polyelectrolytes polyethylenimine and poly-L-lysine do not induce proliferation of E.coli strain. On the other hand, it induces the proliferation of S. aureus strain. Due to CuNPs effectiveness against E.coli strain, CuNPs were selected for further research. The designed coatings at proper NPs share sustained the function of human lung cells cultured within 10 days of culture. The AFM and EDX characterization confirmed copper presence in the layer coating nanomaterial. The presence of CuNPs in polyethyleneimine-based nanocomposite deepens the bacteriostatic effect on E. coli compared with PEI alone. Meanwhile, incorporating CuNPs in PLL at share allowed A549 cell maintenance, did not exert a bacteriostatic influence on the examined strain.Conclusion: The platform based on polyelectrolytes incorporated with copper nanoparticles ensuring the growth and morphology of the human lung epithelial cells can be considered an element of the system components for medical devices for maintaining the human lung cells' function.

Porous structures and micropatterning surfaces play a crucial role in the development of highly sensitive force sensors. However, achieving these two conductive architectures typically requires complex materials synthesis and expensive manufacturing processes. In this study, we introduce a novel conductive composite film featuring a porous/micropyramid hybrid conductive architecture, which is achieved through a straightforward process of materials mixing and one-step screen printing. By utilizing a deep eutectic solvent in the ink component, micropores are induced in the printed composite, while the mesh of the screen mask acts as a template, resulting in a micropyramid film surface. We have successfully realized highly sensitive flexible force sensors with multifunctional capabilities for perceiving normal force and shear force.

In current work, we illustrate the effect of adding small amount of Carbon to very common Co2MnSi Heusler alloy based-glass coated microwires. A significant change in the magnetic and structure structural properties has observed for the new alloy Co2MnSiC compared to the Co2MnSi alloy. The magneto-structural investigations have performed to clarify the main phys-ical parameters i.e., structural & magnetic at a wide range of measuring temperature. The XRD analysis illustrated the well-defined crystalline structure with average grain size (Dg = 29.16 nm) and a uniform cubic structure with A2-type compared to the mixed L21 and B2 cubic structures for Co2MnSi-based glass coated microwires. The magnetic behaviour has investigated at a tem-perature range (5 to 300 K) and an external applied magnetic field (50 Oe to 20 kOe). The adding of small amount of Carbon to the Co2MnSi matrix enhance the magnetic thermal stability, where the thermomagnetic behaviour of Co2MnSiC glass-coated microwires show a perfect stable be-haviour for a temperature range from 300 K to 5 k, the differences between the coercivity value is only 0.3 Oe compared to 4 Oe for Co2MnSi-sample. In addition, M-H loops measured at tempera-ture below 50 K show unsaturated loops; meanwhile the Co2MnSi loops shows a strong antifer-romagnetic coupling for the loops measured below 50 K. By studying the field cooling (FC) and field heating (FH) magnetizations curves at a wide range of external applied magnetic field we detected a critical magnetic field (H = 1 kOe) where FC and FH curves have a stable magnetic behavior for Co2MnSiC sample, such stability does not find in Co2MnSi sample. We proposed a phenomenal expression to estimate the magnetization thermal stability, ΔM (%), of FC and FH magnetization curves and the maximum value is detected at the critical magnetic field where ΔM (%) ≈ 98 %. The promising magnetic stability of Co2MnSiC glass-coated microwires with tem-perature is due to the changing of the microstructure induced by adding Carbon, as the A2-type structure show a unique stability by variation the temperature and the external magnetic field. In addition, a unique internal mechanical stress, which induced during the fabrication process and plays on controlling magnetic behavior with temperature and external magnetic field. The ob-tained results make Co2MnSiC promising candidate for magnetic sensing devices based Heusler glass-coated microwires.

Air pollutants such as volatile organic compounds (VOCs), nitrogen oxides (NOx), sulfur dioxide (SO2), as well as water pollutants including heavy metal, are harmful to human and environment. Effective control and reduction of their pollution is therefore an important topic for today’s scientists. Fly ash (FA) is a type of industrial waste that can cause multiple environmental problems if discharged into the air. On the other hand, because of its high porosity, large specific surface area, and other unique characteristics, the FA can also be used as a low-cost and high efficient adsorbent with some simple modifications. This paper reviews the effects of FA on treatment of the above air and water pollution based on our research experience over many years, including to the current status of global FA utilization, physicochemical properties, principle of adsorption, and the application direction of FA in the future. It focuses on the use of nanocomposite technology to fabricate functional FA fibrous membranes to adsorb VOCs from air, and treat heavy metal wastewater. This present review first describes the fabrication technology of FA nanocomposites and their mechanism of adsorption VOCs from air. Utilization of nanofiber technology to fabricate multi-functional FA emerging composite materials to mitigate air and water pollution has great potential in the future, especially use of pollutant material to control other pollutants.

The high level of noise in helicopter cabins considerably compromises the comfort and safety of the pilot and passengers. To verify the feasibility and effectiveness of microperforated panel composite sound absorption structures for noise suppression in helicopter cabins, simulation and experimental studies were conducted on a model of a light helicopter cabin. First, three microperforated composite sound absorption structures for the helicopter cabin wall panel were designed. Then, a finite element model of the main gear/body acoustic vibration coupling was established to obtain the target frequencies of the microperforated composite sound absorption structures; the acoustic effect was verified by simulation. Finally, a model helicopter cabin equipped with the three microperforated composite sound absorption structures was built, and a cabin noise test was performed. The test results showed that the combined microperforated panel acoustic structure and microperforated panel–porous material composite structure realized an overall cabin sound pressure level attenuation of 8–10 dB, on average, in the wide frequency range of 500–2000 Hz, with an amplitude of more than 20 dB. The microperforated panel–acoustic supermaterial composite structure achieved low-frequency sound absorption in the frequency range of 300–450 Hz. The sound absorption effect reached 50%, and it also exhibited good noise reduction effects in the middle- and high-frequency bands.

Single-layer core corrugated sandwich panels generally consist of a corrugated core and two layers of panels, while multi-layer core corrugated sandwich panels are formed by stacking multiple layers of panels with multiple layers of core layers. In this study, integrated multilayer core corrugated sandwich panels with different shapes of corrugated cores (triangular, trapezoidal, and rectangular) and the different number of core layers were fabricated using 3D printing technology, and the mechanical behavior of such multilayer core corrugated sandwich panels under quasi-static three-point bending was investigated using experiments and numerical simulations. The effects of core shape and number of core layers on the bending deformation process, damage mode, load carrying capacity, and bending energy dissipation capacity of multilayer core sandwich panels are discussed. Parametric design of multilayer triangular core corrugated sandwich panels was also carried out by finite element software ABAQUS. It was found that a new multilayer corrugated sandwich panel with a multi-layer core is better than the single core shape multilayer corrugated sandwich panel in terms of bending load capacity, energy dissipation capacity and deformation capacity can be obtained through the combination design of different core shapes.

Nowadays, determining the socioeconomic factors' influence on environmental quality is a crucial issue for policymakers. We aim to explore the impact of socioeconomic factors i.e., ethnic conflicts inform ethnic fragmentation, institutions quality effectiveness, and energy consumption on environmental quality by testing the various hypotheses (Pollution Halo Hypothesis, IPAT, and EKC) in 40 selected Asian countries throughout 1993-2019. We also use a set of control variables which are gross domestic product per capita, foreign direct investment inflows, and population growth to determine their impact on environmental quality. We use the Panel Quintile Regression Method of 0.25, 0.5, and 0.75 to analyze the results. We find ethnic conflict negatively affects the environmental quality at all quantiles. The institution's variables regulatory quality and rule of law negatively influence the environmental quality. Our result supports Porter's hypothesis because the effect of direct foreign investment on the amount of CO2 emissions is negative and significant at 0.25, 0.5, and 0.75 quantiles which states that foreign direct investment in the host country supports environmental quality. Furthermore, our results support the IPAT hypothesis in selected Asian countries.

Telecommunication infrastructure, as a technology-intensive industry, provides fundamental support for informatization construction. This paper empirically studies the impact of telecommunication infrastructure construction on economic and social innovative development using provincial panel data from China spanning from 2009 to 2022. The research findings indicate the following: (1) Telecommunication infrastructure significantly promotes innovation in terms of R&amp;D investment, knowledge output, and application output. (2)At various stages of telecommunication technology development, the impact on innovative development varies. Iterative updates in telecommunication technology drive higher R&amp;D expenditures, facilitating better utilization of innovation outcomes in industries. (3) There are regional disparities in the influence of telecommunication infrastructure on economic and social innovative development. In the eastern regions, telecommunication infrastructure construction primarily promotes mobile communication, with clear spillover effects. In contrast, in western regions, it mainly facilitates fixed communication networks. Therefore, in the new development stage of China, further strengthening telecommunication infrastructure construction provides a new impetus and space for economic and social innovative development. It is essential to persistently advance the coordinated construction of mobile and fixed communication infrastructure to achieve regional development coordination.

Based on the seminal paper of Case, Quigley and Shiller (2013), we investigate the effects of financial and housing wealth on consumption. Using quarterly data from 1975 to 2016, for all States of U.S. economy, and a different methodology in measuring wealth, we report relatively greater financial effects than housing effects on consumption. Specifically, in our basic utilized model, the calculated elasticity for financial wealth is 0.060, while for housing is 0.045. The results are not in agreement with the ones obtained by Case, Quigley and Shiller. In an attempt to investigate the disparity we proceed by incorporating the introduction of the Tax Reform Act in 1986, which increased incentives for owner-occupied housing investments. Finally, due to distributional factors at work, and taking into account the pronounced uneven distribution of wealth we investigate the effects of wealth for 8 states that include the Metropolitan areas comprising of the well known Case-Shiller 10-City Composite Index. Now the housing effect on consumption is much stronger and larger than the financial effect. Additionally, we forecast the consumption changes at the time of the high rise and large drops in house prices for these states. Forecasts showed a recession from the fall of Lehman Brothers until the fourth quarter of 2011. These forecasts were not verified. Probably, the new techniques used by politics played an important role. We also find that extreme behaviors cannot be predicted.

The efficacy and cost-effectivness of Multigene Panel Next-Generation Sequencing (NGS) in directing patients towards genomically matched therapies remains uncertain. This study investigated metastatic colorectal cancer (mCRC) patients who underwent NGS analysis on formalin-fixed paraffin-embedded tumor samples. Data from 179 patients were analyzed, revealing no mutations in 39 patients (21.8%), one mutation in 83 patients (46.4%), and two or more mutations in 57 patients (31.8%). KRAS mutations were found in 87 patients (48.6%), including KRAS G12C mutations in 5 patients (2.8%), PIK3CA mutations in 40 patients (22.4%), BRAF mutations in 26 patients (14.5%). Less common mutations were identified: ERBB2 in 5 patients (2.8%) and SMO in 4 patients (2.2%). Additionally, MAP2K1, CTNNB1, and MYC were mutated in 3 patients (2.4%). Two mutations (1.1%) were observed in ERBB3, RAF1, MTOR, JAK1, and FGFR2. No significant survival differences were observed based on mutation numbers. 40% of patients had druggable molecular alterations, but only 1.1% received genomically guided treatment, suggesting limited application in standard practice. Despite this, expanded gene panel testing can identify actionable mutations, aiding personalized treatment strategies in metastatic CRC, although current eligibility for biomarker-guided trials remains limited.

Marine renewable energy is emerging as one of the fast-growing industry in the last decades, as modern society pushes for technologies that can convert energy contained from winds, waves, tides and stream flows. The implementation of renewable energy technologies impose high demands on both structural and environmental engineering, as the energy converters have to work under extreme conditions where parameters such as sea-bottom configuration, water transparency and depth, sea-states and prevailing winds are harsh. Constant monitoring of the marine environment is crucial in order to keep this sector reliable. Active acoustics is becoming a standard tool to collect multi-dimensional data from physical, geological and biological properties of the marine environment. The Div. of Electricity of Uppsala University have been developing an environmental monitoring platform based on sonar (Sound Navigation And Raging) systems. This platform aims to monitor the installation, operation and decommissioning of marine renewable energy converters. The focus will be given the observations of behaviours of marine animals in vicinity of energy converters but also structural inspection and monitoring of MRETs. This paper describes how this multifunctional environmental monitoring platform come to existence from the design to the deployment phase.

The aim of this work is to explain the behaviour of the multiresistance percentage of Pseudomona aeruginosa in some countries of Europe through a multivariate statistical analysis and machine learning validation, using data from the European Antimicrobial Resistance Surveillance System, the World Health Organization and the World Bank. First, we will use a descriptive analysis and a principal components analysis. Then, we use a k-means clustering to determine the countries and regions that are most affected by the antibiotic resistance. Second, we expand the database by adding some socioeconomic, governance and antibiotic-consumption variables. We then run a data panel regression analysis to determine some functions that relates the multiresistance percentage with those new variables. Finally, we use machine learning techniques to validate a pooling panel data case, using XGBoost and random forest algorithms. The results of the data panel analysis indicate that the most important variables for the multiresistance percentage are corruption control and the rule of law. Similar results are found with the machine learning validation analysis, where the human development index is an additional important variable for the multiresistance percentage.

In estimating logistic regression models, convergence of the maximization algorithm is critical, however, this may fail. Numerous bias correction methods for maximum likelihood estimates of the parameters have been conducted for cases of complete data sets and also longitudinal models. For binary response fixed effects panel data model, the conditional logit estimator is consistent for balanced data. When faced with missing covariates problem, researchers opt for various imputation techniques to make the data complete and without loss of generality consistent estimates still suffice asymptotically. For maximum likelihood estimates of the parameters for logistic regression in cases of imputed covariates, the optimal choice of an imputation technique which yields the best estimates with minimum variance is still elusive. The main aim of this paper is to examine the behaviour of the Hessian matrix with optimal values of the imputed covariates vector which will make the Newton-Raphson algorithm to converge faster through a reduced absolute value of the product of the score function and the inverse fisher information component. We focus on a method used to modify the conditional likelihood function through partitioning of the covariate matrix. We also confirm from the moduli of the Hessian matrices that the log likelihood of a panel data logistic model has a global maximum as the parameter estimates. Simulation results reveal that model based simulation perform better than classical imputation techniques yielding estimates with smaller bias and higher precision for the conditional maximum likelihood estimation of nonlinear panel models with single fixed effects.

The COVID-19 pandemic introduced risks and challenges to global food and nutrition security. In this paper, we examine the impact of the COVID-19 pandemic on the nutritional intake of China's rural residents using panel data and a fixed effect model. The data were collected in 2019 and 2020 and covered nine provinces and 2,631 households in rural China. The results reveal that an increase of 100 confirmed cases in a county resulted in a 1.48% (p<0.01), 1.46% (p<0.01), 1.77% (p<0.01), and 1.23% (p<0.01) decrease in per capita intake of dietary energy, carbohydrates, fats, and proteins, respectively. Moreover, the COVID-19 pandemic only had a significant and negative effect on dietary energy intake in the low-income group at the 5% level of significance. Our study indicates that the potential insufficient nutrition situation, nutritional imbalance, and dietary imbalance of low-income rural residents should be addressed appropriately.

Discovery of novel variants from data derived from local population provides confident targets for developing biomarkers for personalized medicine. Biomarker discovery would be an important tool in advancing and utilizing the concept of precision and personalized medicine in the clinic. We identified the need to generate high quality sequencing data from local population and understand the pattern of occurrence of variants in colorectal cancer patients. In this report, we used archived samples from Saudi Arabia and used Ampliseq Comprehensive Cancer panel to identify novel somatic variants. We report a comprehensive analysis of next generation sequencing results with a coverage of >300X. We identified 466 novel variants which were previously unreported in COSMIC and ICGC databases. We analyzed the genes associated with these variants in terms of their frequency of occurrence, probable pathogenicity and clinicopathological features. Among pathogenic somatic variants, 174 were identified for the first time in large intestine. APC, RET and EGFR genes were most frequently mutated. Higher number of variants were identified in left colon. Occurrence of variants in ERBB2 was significantly correlated with those of EGFR and ATR genes. Network analyses of the identified genes provide functional perspective of the identified genes and suggest affected pathways and probable biomarker candidates. This report lays the ground work for biomarker discovery and identification of driver gene mutations in local population.

This research aims to study the ultimate limit state (ULS) behaviour of stiffened panel under longitudinal compression by non-linear finite element method (NLFEM). There are different types of stiffeners being used in shipbuilding i.e. T-bar, flat-bar and angle-bar. However, this research focuses on the ultimate compressive strength behaviour of flat-bar stiffened panel. A total of 420 of reliable scenarios of flat-bar stiffened panel are selected for numerical simulation by ANSYS NLFEM. The ultimate strength behaviours obtained were used as data for the development of closed form shape empirical formulation. Recently, Kim et al. [1] proposed for advanced empirical formulation for T-bar stiffened panel and the applicability of the proposed formulation to flat-bar stiffened panel will be confirmed by this study. The accuracy of the empirical formulation obtained for flat-bar stiffened panel has been validated by FE simulation results of statistical analysis (R2 = 0.9435). The outcome obtained will be useful for ship structural designers in predicting the ultimate strength performance of flat-bar type stiffened panel under longitudinal compression.

Among colours, the green has the most sensitivity in human vision so that green defects on displays can be effortlessly perceived by a photopic eye with the most intensity in the wavelength 555 nm of the spectrum. With the market moving forward to high resolution, displays can have resolutions of 10 million pixels. Therefore, the task detects the appearance the panel using ultra-high resolutions in TFT-LCD. The machine vision associated with reflective chromaticity spectrometer quantises the defects are explored, such as blackening and whitening. The result shows the significant phenomena to recognize the non-uniformity film-related chromatic tendency. In contrast, the quantitative assessment illuminates that the chromaticity CIE xyY at 0.001 is a just noticeable difference (JND) and detects even more sensitivity. Moreover, an optical device associated with a 198 Hg discharge lamp calibrates the spectrometer accuracy.

A new lateral force-resisting wall panel is presented for applications in mid-rise prefabricated lightweight steel construction in seismic prone regions. This panelised system is composed of a hot-rolled frame and cold-formed studs and tracks, which works as a lateral force resisting system in lightweight steel framing. The proposed hybrid panel system exhibits proper ductility and energy dissipation behaviour. The hysteretic responses of full-scale panel experiments demonstrate that the system can safely resist high cyclic loads. The hot-rolled steel part, on the other hand, can significantly improve the initial lateral stiffness of the total system that will control the maximum allowable drift of multi-story buildings. Finally, in a case study, by applying the proposed system to the design of a mid-rise building in a high seismic area, the performance of the hybrid panels, are compared with those of fully hot-rolled systems (moment resisting frames) and fully cold formed systems. The findings indicate that applying hybrid panels will result in lower weights and better performance in seismic prone regions.

The ever deepening population aging has brought opportunities and challenges to the continued expansion of tourism consumption in China. In this article, the impact of population aging on household tourism consumption was studied from both theoretical and empirical aspects. First, the micro mechanisms of the impact of population aging on household tourism consumption were analyzed, which include economic condition mechanism, intergenerational care mechanism, health status mechanism and Internet use mechanism. Subsequently, the impact of population aging on household tourism consumption and its impact mechanisms were tested, and the heterogeneity analysis was conducted, by using the data of China Family Panel Studies (CFPS) from 2014, 2016 and 2018. The main conclusions of the article are as follows: (1) Population aging has a significant negative impact on household tourism consumption, and a series of robustness test results such as endogenous treatment support this finding. (2) The results of the impact mechanism test show that population aging has a negative mediating effect on household tourism consumption by reducing household economic conditions. The moderating effect of intergenerational care on the effect of population aging on household tourism consumption is insignificant. Health status of the elderly and Internet use have a significant positive moderating effect on the impact of population aging on household tourism consumption. (3) The results of the heterogeneity analysis show that the negative impact of population aging on household tourism consumption in urban areas is greater than that in rural areas, and the negative impact of population aging on household tourism consumption of families with the old-old elderly is greater than that of falimies with the young-old elderly. The conclusions of this article provide important references for activating tourism consumption in China in the context of population aging.

A Pacific brittle star Ophiura sarsii has previously been shown to produce a chlorin (3S,4S)-14-Ethyl-9-(hydroxymethyl)-4,8,13,18-tetramethyl-20-oxo-3-phorbinepropanoic acid (ETPA) (1) with potent phototoxic activities making it applicable to photodynamic therapy. Using extensive LC-MS metabolite profiling, molecular network analysis and targeted isolation with de novo NMR structure elucidation, we here identify five additional chlorin compounds from O. sarsii and its deep-sea relative O. ooplax: 10S-Hydroxypheophorbide a (2), Pheophorbide a (3), Pyropheophorbide a (4), (3S,4S,21R)-14-Ethyl-9-(hydroxymethyl)-21-(methoxycarbonyl)-4,8,13,18-tetramethyl-20-oxo-3-phorbinepropanoic acid (5), and (3S,4S,21R)-14-Ethyl-21-hydroxy-9-(hydroxymethyl)-4,8,13,18-tetramethyl-20-oxo-3-phorbinepropanoic acid (6). Chlorins 5 and 6 have not been previously reported in natural sources. Interestingly, low amounts of chlorins 1-4 and 6 could also be identified in a distant species, the basket star Gorgonocephalus cf. eucnemis, demonstrating that chlorins are produced by a wide spectrum of marine invertebrates of the class Ophiuroidea. Following purification of these major Ophiura chlorin metabolites, we discovered the high singlet oxygen quantum yield upon their photoinduction and their strong phototoxicity against a panel of cancer cell lines. These studies identify an arsenal of brittle star chlorins as powerful natural photosensitizers with potential photodynamic therapy applications.

Following the rapid spread of COVID-19 across the globe, the intense response that was demanded of diagnostic centers and research laboratories prompted the use of numerous products and protocols for the management of SARS-CoV-2 specimens. In these settings, proper handling of such infectious specimen is necessary to ensure the safety of personnel and to reduce the risk of active transmission. Our aim was to evaluate the inactivation efficacy of different inactivating methods, notably from commercial lysis buffers available in diagnostic kits. Heat and sodium dodecyl sulfate detergent were also included in our investigations. A cell culture-based assay was used, and supported by molecular qRT-PCR detection, to show in vitro infectivity reduction after inactivation treatment. Overall, all the investigated methods were successful in inactivating SARS-CoV-2. Ten minutes of contact with the commercial buffers completely stopped in vitro SARS-CoV-2 infectivity. Fifteen minutes at 68°C and 30 minutes at 56°C as well as one hour with sodium dodecyl sulfate detergent at 2, 1, 0.5, and 0.1% yielded the same results. These findings demonstrate the reliability of these protocols with regards to biosafety. Inactivation by heat and sodium dodecyl sulfate detergent are rather simple and can be readily available methods for rendering an infectious SARS-CoV-2 specimen inactive, especially in settings where commercial buffers are not available.

This study analyzes the effect of economic growth and income distribution on health inequality using data from the Organization for Economic Cooperation and Development (OECD). A panel analysis was conducted by combining 21 years of data (from 2000 to 2020) from 38 OECD countries. Life expectancy and avoidable mortality were set as the dependent variables; gross domestic product and poverty gap were set as the independent variables; body mass index, consumption, smoking rate, healthcare personnel, number of beds in health service facilities, national medical expenses, and unemployment were set as control variables. First, economic growth and poverty gap significantly affect life expectancy and avoidable mortality. It has been confirmed that to resolve health inequality, growth during growth and distribution must be prioritized. Second, it has been confirmed that as the poverty gap increases, life expectancy increases and the avoidable mortality rate decreases. A mechanism different from the existence of a medical security system targeting the lowest class or an increase in the welfare of society worked. In conclusion, as a policy proposal to alleviate health inequality, this study suggests that policy intervention is necessary to block or alleviate the negative impact of income inequality in health care policies.

Abstract: The VSI represents a significant advancement in the assessment of gastrointestinal-specific anxiety among patients with Irritable Bowel Syndrome (IBS) and other Chronic Inflammatory Bowel Diseases (IBD). However, an Italian version of the instrument is not yet available for the reference population. This study utilized a national sample of 500 individuals, including healthy controls and patients with Ulcerative Colitis and Crohn's Disease, to test the validity and reliability of the Italian VSI. Using back-translation methodology to ensure translation fidelity, the research applied a questionnaire and the VSI through an online format to 500 participants. Data analysis revealed that the Italian VSI had excellent psychometric properties, demonstrating high internal consistency (Cronbach’s α = 0.95) and construct validity. The scale proved sensitive in detecting significant differences in visceral sensitivity among groups, highlighting its utility as a clinical and research assessment tool. Specifically, the Italian VSI exhibited a unidimensional factorial structure and maintained a strong correlation with other measures of anxiety and the severity of gastrointestinal symptoms, confirming its role in enhancing the understanding and management of IBS and IBD in Italy.

With the popularity of solar energy in the electricity market, demand arises for data such as precise locations of solar panels for efficient energy planning, management, and distribution. However, this data is not easily accessible and in some cases, information such as precise locations does not exist. Furthermore, existing data sets for training semantic segmentation models of PV installations are limited, and their annotation is time-consuming and labor-intensive. Therefore, for additional remote sensing (RS) data creation, the pix2pix generative adversarial network (GAN) is utilized, enriching the original resampled training data of varying GSDs without compromising its integrity. Experiments done with the DeepLabV3 model, ResNet-50 backbone, and pix2pix GAN architecture were conducted to find the optimal configuration for an accurate RS imagery segmentation model. The result is a fine-tuned solar panel semantic segmentation model, trained using transfer learning and utilizing an optimal amount – 60% of generated RS imagery for additional training data, increasing model accuracy. The findings demonstrate the benefits of using GAN-generated images as additional training data, increasing the size of small data sets, and improving the capabilities of the segmentation model for solar panel detection in RS images.

This study examines whether gas is emitted from the materials used in the fabrication of metal vacuum panels or not and if emitted, their degree as time goes by. As experimental materials, metal sheets, foamed concrete as a core material, and polymer materials as a sealing material between metal sheets were selected. Experiments on the type and the degree of bending of metal materials showed that aluminum’s vacuum reaching time of 0.001 torr was at least 40 sec to 90 sec in its flat plate, but its vacuum reaching time increased from 3 times to 4.5 times in case of 90 ° and 135 ° bending state. For this reason, it is judged that stainless steel or steel material is suitable because aluminum is inadequate in terms of processability at the time of fabricating the metal vacuum panel. Also, vacuum arrival times and weight changes with increasing foam content of inorganic foamed concrete increased from 22,000 sec to 42,000 sec with increasing foaming rate and also, the weight change increased from 1.7% to 8%. Also, the experimental results on the type of honeycomb materials, the PE (polyethylene) with a vacuum reaching time of 30,000 sec and with a weight change of 0.5% and the PTFE (Poly-tetrafluoro ethylene) with a vacuum reaching time of 29,000 sec and with a weight change of 2.2% showed the optimum value.

Wastewaters containing synthetic dyes, namely molecules with large aromatic structure which can produce harmful effects on the aquatic environment, are difficult to treat. Accordingly, and based on the adsorption technology, this work proposes the use of porous carbons as adsorbents of a red dye used in the wood industry. Three porous carbonaceous materials with relatively high porosity and tunable pore size were prepared by transformation of a nitrogen-rich precursor, polyacrylonitrile (PAN), at high temperature: N doped carbon (PAN-C), N-doped activated carbon with potassium hydroxide (PAN-C-Act) and N, S-co doped carbon with sulphur (PAN-S-C). Different experiments were planned to study the influence of pH (1.9-2.3, 6-6.8 and 11.8-12.6), solid/liquid ratio (S/L, 0.43-0.53 and 1.73-1.91 g L−1) and initial concentration (24 – 28 mg L−1 and 231 – 285 mg L−1) on the dye removal from aqueous solutions. The best results were found for the activated carbon (PAN-C-Act) at all concentrations and pH essayed. Specifically, the maximum adsorption capacity of 602.3 mg g−1 (99.9%, adsorption yield) was obtained at S/L of about 0.5 g L−1, acid pH, 285 mg L−1 and 48 h. Adsorption kinetics was better explained by the pseudo-second order model. Also, the existence of external mass transfer and intra-particle diffusion was confirmed.

This paper addresses investigation of guided-wave excitation by angle-beam wedge piezoelectric transducers in multi-layered composite plate structure with orthotropic symmetry of the material. The aim of the present study is to determine the capability of such actuators to provide the controlled generation of an acoustic wave of a desirable type with the necessary wavelength, propagation distance and directivity. The studied CFRP panel is considered as homogenous with effective elastic moduli and anisotropic structural damping, whose parameters were determined experimentally. According to the results of dispersion analysis and taking into account the data of wave attenuation in a highly damping CFRP composite, the two types of propagating waves A0 and S0 were considered theoretically and experimentally in the frequency range 10 - 100 kHz. Using the results of a previous study, the structure of the wedge actuator was reconstructed to develop its finite element (FE) model, and a modal analysis was carried out, which revealed the most intense natural vibration modes and their eigenfrequencies within the used frequency range. Both experimental and numerical studies of the generation, propagation, directivity and attenuation of waves in the orthotropic composite panel under study revealed the influence of the angular orientation of the actuator on the formation of wave patterns and allowed to determine the capabilities of the wave's directivity control.

This study attempts to assess the impact of corruption on economic growth in the Mediterranean countries, during the period from 1998 to 2007. Econometric analysis using panel regression has been adopted to test this effect. Individual effects models such as random effects model and fixed effects model were applied to the study sample of 160 observations, and to choose the suitable model, we implemented several tests. For our analysis, we used a basic model that includes the dependent variable GDP per capita as a factor of economic growth and the corruption perception index as the independent variable concerned. Then we completed the model with several standardized macroeconomic control variables mentioned above and applied the individual effects models. The outcomes illustrate that corruption has a negative impact on the selected Mediterranean countries’ economic growth.

Setting A high proportion of notified tuberculosis cases in the Philippines are clinically diagnosed (63%) as opposed to bacteriologically confirmed. Better understanding of this phenomenon is required to improve tuberculosis control. Objectives To determine the percentage of Smear Negative Presumptive Tuberculosis patients that would be diagnosed by GeneXpert; compare clinical characteristics of patients diagnosed as tuberculosis cases; and review the impact that the current single government physician and a reconstituted Tuberculosis Diagnostic committee (Expert Panel) may have on tuberculosis over-diagnosis. Design This is a cross-sectional study of 152 patients 15-85 years old with two negative Direct Sputum Smear Microscopy results, with abnormal chest X-ray who underwent GeneXpert testing and review by an Expert Panel. Results 31% (48/152) of the sample were Xpert positive. 93% (97/104) of GeneXpert negatives were clinically diagnosed by a Single Physician. Typical symptoms and X-ray findings were higher in bacteriologically confirmed tuberculosis. When compared to GeneXpert results, the Expert panel’s sensitivity for active tuberculosis was high (97.5%, 39/40) but specificity was low (40.2%, 35/87). Conclusion Using the GeneXpert would increase the level of bacteriologically confirmed tuberculosis substantially among presumptive Tuberculosis. An Expert panel will greatly reduce over-diagnosis usually seen when a decision is made by a Single Physician.

We report fabrication of a multifunctional photonic integrated chip on lithium niobate on insulate (LNOI), which is achieved by femtosecond laser assisted chemo-mechanical polish. We demonstrate a high extinction ratio beam splitter, a 1 × 6 optical switch, and a balanced 3 × 3 interferometer on the fabricated chip by reconfiguring the microelectrode array integrated with the multifunctional photonic circuit.