This paper introduces an innovative nanotechnology-based approach that provides a pathway to enhance the energy release efficiency of nanoenergetic materials (nEMs) by harnessing self-synchronized collective atomic vibrations and phonon wave resonance within the transition domains between nanocomponents, without altering the material composition. The key innovation involves incorporating finely-tuned 2D-ordered linear-chain carbon-based multilayer nano-enhanced interfaces as programmable nanodevices into the transition domains using advanced multistage processing and assembly techniques. These programmable nanodevices enable precise control over self-synchronized collective atomic vibrations and phonon wave propagation, leading to synergistic effects. To activate and optimize these effects, a combination of various methods is employed, including energy-driven initiation of allotropic phase transformations, surface acoustic wave-assisted micro/nano-manipulation, heteroatom doping, directed self-assembly using high-frequency electromagnetic fields, and data-driven inverse design approaches. By leveraging a data-driven inverse design strategy and uncovering hidden structure-property relationships, we maximize energy release efficiency using the carbon nano-materials genome approach derived from multifactorial neural network-based predictive models. This approach not only unlocks new functionalities in nEMs but also improves environmental performance and safety levels. By pioneering transformative pathways for nEMs through harnessing phonon wave resonance in low-dimensional nanocarbon transition interfaces, this research brings significant advancements in the field.

The influence of growth temperature on the crystalline quality and optical properties of AlGaN at 325 nm, grown using plasma-assisted molecular beam epitaxy (MBE), was investigated. The growth temperature exhibited a significant impact on the growth mode and surface morphology. Specifically, at a growth temperature of 750 degrees Celsius, when appropriate Al and Ga flow rates were employed, the AlGaN layer exhibited exceptional surface morphology and favorable optical properties. The optical properties of the AlGaN material were explored, revealing the presence of two distinct non-radiative recombination centers characterized by different activation energies. The minority carrier lifetimes were measured as 560 ps at 10 K and 64 ps at room temperature. The underlying mechanism was analyzed from the perspective of carrier dynamics, shedding light on the observed phenomena.

Nanocrystalline silicon oxide (nc-SiOx:H) is a multipurpose material with its varied application in solar cells as a transparent front contact, intermediate reflector, back reflector layer and even tunnel layer for passivating contacts, owing to easy tailoring of its optical properties. In this work, we systematically investigate the influence of gas mixture (SiH4, CO2, PH3 and H2), RF power and process pressure on the optical, structural and passivation properties of thin n-type nc-SiOx:H films prepared in an industrial, high throughput, plasma-enhanced chemical vapor deposition (PECVD) reactor. We provide a detailed description of the n-type nc-SiOx:H material develop-ment using various characterization techniques (SEM, EDX, Raman spectroscopy, and spectro-scopic ellipsometry) with a focus on the relationship between the material properties and the pas-sivation they provide to n-type c-Si wafers characterized by their effective carrier lifetime (τeff). Further, we also outline the parameters to be kept in mind while developing different n-type nc-SiOx:H layers for different solar cell applications. We report a tunable optical gap (1.8 – 2.3 eV) for our n-type nc-SiOx:H films as well as excellent passivation properties with τeff up to 3.5 ms (iVoc ~ 715 mV) before annealing. Oxygen content plays an important role in determining the crystallinity and hence passivation quality of the deposited nanocrystalline silicon oxide films.

In this paper, we aim to present real implementation cases where non-visible elements of environmental impact assessments (EIA), wind flow, are visualized using a 3D digital twin technology. The conventional EIA process serves as a crucial tool in the evaluation of potential environmental impacts prior to the initiation of development projects. This evaluation helps to establish a legal and institutional framework that seeks to minimize the adverse effects on the environment. However, traditional EIA methods present challenges, particularly for non-experts, in comprehending the results of assessments involving non-visible environmental factors such as noise, air quality, and wind flow. These elements are often represented in static images or numerical tables, limiting accurate understanding and engagement. Our proposed method, termed Digital Twin based EIA, addresses these limitations by leveraging digital twin technology. This advanced methodology allows for the visualization of non-visible environmental elements in a spatio-temporal dimension, providing a more interactive and comprehensive user interface/experience for both citizens and stakeholders. In this context, we present a unique case study that focuses on visualizing wind flow using this technology. This paper serves as an example of how digital twin platforms can enhance traditional EIA processes, offering a more immersive and informative experience. The evolution of EIA into the digital realm signifies an important step forward in fostering public understanding and engagement in environmental protection efforts.

A low-cost bio-mass-derived carbon substrate has been employed to synthesize MoS₂@carbon composites through a hydrothermal method. Carbon fibers derived from natural cotton provide a three-dimensional and open framework for the uniform growth of MoS₂ nanosheets, thus constructing hierarchically coaxial architecture. The unique structure could synergistically benefit fast Li-ion and electron transport from the conductive carbon scaffold and porous MoS₂ nanostructures. As a result, the MoS₂@carbon composites, when served as anodes for Li-ion batteries, exhibit a high reversible specific capacity of 820 mAh g^-1, high-rate capability (457 mAh g^-1 at 2 A g^-1), and excellent cycling stability. The superior electrochemical performance makes the MoS₂@carbon composites to be low-cost and promising anode materials for Li-ion batteries.

Structural self-organizing and pattern formation are universal and key phenomena observed during growth and cluster-assembling of the carbyne-enriched nanostructured metamaterials at the ion-assisted pulse-plasma deposition. Fine tuning these universal phenomena opens access to designing the properties of the growing carbyne-enriched nano-matrix. The structure of bonds in the grown carbyne-enriched nano-matrices can be programmed by the processes of self-organization and auto-synchronization of nanostructures. We propose the innovative concept, connected with application of the universal Cymatics phenomena during the predictive growth of the carbyne-enriched nanostructured metamaterials. We also propose the self-organization approach for increase stability of the long linear carbon chains. The main idea of suggested concept is manipulating by the self-organized wave patterns excitation phenomenon and their distribution by the spatial structure and properties of the nanostructured metamaterial grows region through the new synergistic effect. Mentioned effect will be provided through the vibration-assisted self-organized wave patterns excitation along with simultaneous manipulating by their properties through the electric field. We propose to use acoustic activation of the plasma zone of nano-matrix growing. Interaction between the inhomogeneous electric field distribution generated on the vibrating layer and the plasma ions will serve as the additional energizing factor controlling the local pattern formation and self-organizing of the nano-structures. Suggested concept makes it possible to provide precise predictive designing the spatial structure and properties of the advanced carbyne-enriched nanostructured metamaterials.

Three-dimensional V₂O₅ hollow structures have been prepared through a simple synthesis strategy combining solvothermal treatment and a subsequent thermal annealing. The V₂O₅ materials are composed of microspheres 2–3 μm in diameter and with a distinct hollow interior. The as-synthesized V₂O₅ hollow microspheres, when evaluated as a cathode material for lithium-ion batteries, can deliver a specific capacity as high as 273 mAh·g⁻¹ at 0.2 C. Benefiting from the hollow structures that afford fast electrolyte transport and volume accommodation, the V₂O₅ cathode also exhibits a superior rate capability and excellent cycling stability. The good Li-ion storage performance demonstrates the great potential of this unique V₂O₅ hollow material as a high-performance cathode for lithium-ion batteries.

Achieving the thermal conductivity required for efficient heat management in semiconductors and other devices requires the integration of thermally conductive ceramic fillers at concentrations of 60 vol% or higher. However, the increased filler content often negatively affects the mechanical properties of the composite matrix, limiting its practical applicability. To address this issue, in this paper, we present a new strategy to reduce the required ceramic filler content: the use of a thermally conductive ceramic composite filler with carbon nanotubes (CNT) grown on aluminum nitride (AlN). We have combined catalyst coating technology with vacuum filtration to ensure that the catalyst is uniformly applied to micrometer-sized AlN particles, followed by efficient and uniform synthesis of CNTs using a water-assisted process in a vertical furnace. By carefully controlling the number of vacuum filtration cycles and the growth time of the CNTs, we demonstrate precise control over the number and length of the CNT layers, thereby adjusting the properties of the composite to the intended specifications. When AlN/CNT hybrid fillers are incorporated into silicone rubber, while maintaining the mechanical properties of rubber, the thermal diffusivity achieved at reduced filler levels exceeds that of composites using AlN-only or simultaneous AlN and CNTs formulations. This demonstrates the critical role of CNTs on AlN surfaces. Our study represents a significant advancement in the design of thermally conductive materials with potential implications for a wide range of applications.

Direct laser writing three-dimensional nano-lithography is an established technique for manufacturing functional 3D micro- and nano-objects via non-linear absorption induced polymerization process. In this Chapter an underlying physical mechanisms taking place during nano-confined polymerization reaction, induced by tightly focused ultra-short laser pulses, are reviewed and discussed. The special attention is paid on the effects that directly impact structuring resolution and minimum achievable feature size. Analysis of possible photo-initiation mechanisms as contributing multi-photon absorption and avalanche ionization in pre-polymers under diverse exposure conditions (wavelength, pulse duration) is presented. Feasible structuring of pure (non-photosensitized) and functional nanoparticles doped polymer precursors is justified and benefits of such materials/structures for microoptics, photonics and cell scaffolds are highlighted. The influence of temperature effects (induced by writing process itself or determined by ambient conditions) on polymerization process, observed in different pre-polymers under diverse exposure regimes is outlined. The further adjustment of the structuring resolution is possible via precise control of light polarization and diffusion assisted radical quenching. The work is concluded with a brief outlook on future challenges and perspectives related to refinement of 3D ultra-fast laser lithography fabrication process in the means of application of diverse post-processing methods and research into novel photo-curable materials including inorganic ones.

Single-layer core corrugated sandwich panels generally consist of a corrugated core and two layers of panels, while multi-layer core corrugated sandwich panels are formed by stacking multiple layers of panels with multiple layers of core layers. In this study, integrated multilayer core corrugated sandwich panels with different shapes of corrugated cores (triangular, trapezoidal, and rectangular) and the different number of core layers were fabricated using 3D printing technology, and the mechanical behavior of such multilayer core corrugated sandwich panels under quasi-static three-point bending was investigated using experiments and numerical simulations. The effects of core shape and number of core layers on the bending deformation process, damage mode, load carrying capacity, and bending energy dissipation capacity of multilayer core sandwich panels are discussed. Parametric design of multilayer triangular core corrugated sandwich panels was also carried out by finite element software ABAQUS. It was found that a new multilayer corrugated sandwich panel with a multi-layer core is better than the single core shape multilayer corrugated sandwich panel in terms of bending load capacity, energy dissipation capacity and deformation capacity can be obtained through the combination design of different core shapes.

Diseases in articular cartilages have affected millions of people globally. Although the biochemical and cellular composition of articular cartilages is relatively simple, there is the limitation in self-repair ability of cartilage. Therefore, developing the strategies for cartilage repair is very important. Here, we reported a new manufacturing process of water-based polyurethane based photosensitive materials with hyaluronic acid and applied the materials for 3D printed customized cartilage scaffolds. The scaffold has high cytocompatibility and is one that closely mimics the mechanical properties of articular cartilages. It is suitable for culturing human Wharton's jelly mesenchymal stem cells (hWJMSCs) and the cells showed an excellent chondrogenic differentiation capacity. We consider that the 3D printing hybrid scaffolds may have potential in customized tissue engineering and facilitate the development of cartilage tissue engineering.

The objective of this study was to detail the monomer composition of resin-based dental materials sold in the market in 2023 and to evaluate the proportion of BPA derivatives in relation with their applications. A search on manufacturers’ websites was performed to reference resin-based dental materials currently on the market. Their monomer composition was determined from material safety data sheets and completed with a search on PubMed database. Among the 543 material compositions exploitable, 382 (70.3%) contained BPA derivatives. Among them, 56.2% contained BisGMA, 28% BisEMA, the most frequently reported. A total of 59 monomers of which 6 BPA-derivatives were found. 309 materials (56.9%) contained UDMA and 292 (53.8%) TEGDMA. Less than one third of materials identified contained no BPA derivatives. These proportions vary a lot depending on their applications with materials dedicated to dental care of young populations containing the highest proportions of BPA-derivatives monomers. The long-term effects on human health of the different monomers identified including BPA-derivatives monomers is a source of concern. For children and pregnant or lactating women arises the question to take a precautionary principle and avoid the use of resin-based dental materials likely to release BPA by opting for alternative materials.

Digital Twin Cities (DTCs) play a fundamental role in city planning and management. They allow three-dimensional modeling and simulation of cities. 3D semantic segmentation is the foundation for automatically creating enriched DTCs, as well as their updates. Past studies indicate that prior level fusion approaches demonstrate more promising precisions in 3D semantic segmentation compared to point level fusion, features level fusion, and decision level fusion families. In order to improve point cloud enriched semantic segmentation outcomes, this article proposes a new approach for 3D point cloud semantic segmentation through developing and benchmarking three prior level fusion scenarios. A reference approach based on point clouds and aerial images was proposed to compare it with the different developed scenarios. In each scenario, we inject a specific prior knowledge (geometric features,classified images ,etc) and aerial images as attributes of point clouds into the neural network’s learning pipeline. The objective is to find the one that integrates the most significant prior knowledge and enhances neural network knowledge more profoundly, which we have named the "smart fusion approach". The advanced Deep Learning algorithm "RandLaNet" was adopted to implement the different proposed scenarios and the reference approach, due to its excellent performance demonstrated in the literature. The introduction of some significant features associated with the label classes facilitated the learning process and improved the semantic segmentation results that can be achievable with the same neural network alone. Overall, our contribution provides a promising solution for addressing some challenges, in particular more accurate extraction of semantically rich objects from the urban fabric. An assessment of the semantic segmentation results obtained by the different scenarios is performed based on metrics computation and visual investigations. Finally,the smart fusion approach was derived based on the obtained qualitative and quantitative results.

Quasi-solid composited electrolytes were produced by LiFSI initiated polymerized poly-(Dioxolane) (PDOL) with garnet-LLZO (Li7La2Zr3O12) nanofibers and used in lithium-metal batteries. Linear sweep voltammetry shows that the initial oxidation voltage of 4.6 V for Gel-10% (G10, 10% wt. LLZO in PDOL) vs Li/Li+. EIS test of stainless steel// stainless steel symmetric cells for Gel-1% (G1), Gel-5% (G5) and Gel-10% (G10) show ion conductivity (5*10-5 S/cm). Li/G10/Li symmetric cells have stable stripping-plating cycling performance over 1300 hours continuously with the current density of 0.1 mA/cm2 at 25 oC, indicating a good interface contact and stable lithium-ion transport pathway through the composite electrolytes. LFP/G10/Li batteries have stable charge-discharge plateau, low polarization voltage of 0.07-volt, energy efficiency of 95% and coulombic efficiency of ~99% at current density of 26.3 mA/g at 25 oC for over 100 cycles.

3D plotting is an additive manufacturing technology enabling biofabrication, thus the integration of cells or biologically sensitive proteins or growth factors into the manufacturing process. However, most (bio-)inks developed for 3D plotting were not shown to be processed into clinical relevant geometries comprising critical overhangs and cavities, which would collapse without a sufficient support material. Herein, we have developed a support hydrogel ink based on methylcellulose (mc), which is able to act as support as long as the co-plotted main structure is not stable. Therefore, 6 w/v %, 8 w/v % and 10 w/v % mc were allowed to swell in water, resulting in viscous inks, which were characterized for their rheological and extrusion properties. The successful usage of 10 w/v % mc as support ink was proven by multichannel plotting of the support together with a plottable calcium phosphate cement (CPC) acting as main structure. CPC scaffolds displaying critical overhangs or a large central cavity could be plotted accurately with the newly developed mc support ink. The dissolution properties of mc allowed complete removal of the gel without residuals, once CPC setting was finished. Finally, we fabricated a scaphoid bone model by computed tomography data acquisition and co-extrusion of CPC and the mc support hydrogel.

Firefighters Protective Clothing consist of several layers of different properties and functions. The layers create barriers against dangerous outer factor. However, they are also barriers to transport of sweat produced by human organism. It causes that very often sweat in the form of vapor is not transferred effectively from the human organism through the FPC to environment. This leads to sweat condensation on the skin of the FPC user causing his discomfort. In order to ensure as good as possible physiological comfort of firefighter while firefighting and other rescue actions it is necessary to take into consideration the transport of condensed sweat in the multilayer textile set creating the FPC. In the presented work four variants of multilayer textile sets for the FPC have been tested in the aspect of liquid moisture transport. Measurement was performed by means of the Moisture Management Tester (MMT290) – innovative instrument manufactured by the SDL Atlas. Obtained results showed that the transfer of sweat in liquid form occurs only in the inner, next to skin layer of the multilayer sets for the FPC.

Wafer-scale blue micro-light-emitting diode (micro-LED) arrays are fabricated with a pixel size of 12 μm, a pixel pitch of 15 μm, and a pixel density of 1692 pixels per inch, achieved by optimizing the properties of e-beam-deposited and sputter-deposited indium tin oxide (ITO). Although the sputter-deposited ITO (S-ITO) films exhibit a densely packed morphology and lower resistivity compared to those of the e-beam-deposited ITO (E-ITO) films, the forward voltage (VF) values of a micro-LED with the S-ITO films are higher than those with the E-ITO films. The VF values for a single pixel and for four pixels with E-ITO films are 2.82 V and 2.83 V, respectively, while the corresponding values for S-ITO films are 3.50 V and 3.52 V. This was attributed to ion bombardment damage and nitrogen vacancies in the p-GaN layer. Surprisingly, the VF variations of a single pixel and of four pixels with the optimized E-ITO spreading layer from five different regions are only 0.09 V and 0.10 V, respectively. This extremely uniform VF variation is suitable for realizing micro-LED displays to be used in AR and VR applications, circumventing the bottleneck in the development of long-lifespan and high-brightness organic LED devices for industrial mass production.

Tissue-like phantoms are widely used as a model for mimicking the optical properties of live tissue. This paper presents the results of a diffusion reflection method as well as fluorescence lifetime imaging microscopy measurements of fluorescein-conjugated gold nanorods in solution as well as inserted in solid tissue-imitating phantoms. A lack of consistency between the fluorescence lifetime results of the solutions and the phantoms raises a question about the ability of tissue-like phantoms to maintain the optical properties of inserted contrast agents.

With the advancement of Additive Manufacturing and its applications in various industrial segments, it becomes increasingly important to investigate the processability parameters associated with nano-reinforcement. This study examines the influence of infill parameters, such as patterns (hexagonal, triangular and concentric), shape (solid and honeycomb) and concentrations by mass of Carbon Nanotubes (CNTs) at 1.0 wt% and 2.0 wt% on the mechanical compression properties of the 3D printed material. In this sense, nanocomposites based on Polylactic Acid (PLA) matrix nano-reinforced by CNTs were characterized using the Scanning Electron Microscopy -SEM, X-ray Diffraction, Raman Spectroscopy techniques and mechanical analysis. The mechanical properties of both the matrix and the nanocomposites were determined through mechanical compression tests, in accordance with [1]. SEM revealed compacted regions, voids, and detachment in the structures. XRD characterization indicated PLA predominantly amorphous nature, while CNTs exhibited characteristic diffractions of carbon nanotubes. Raman characterization showcased bands and characteristic vibrations of CNTs and PLA, nanocomposites' vibrational modes combine those of CNTs and PLA. Mechanical compression analysis indicates a direct influence of infill pattern, shape, and nano-reinforcement. The triangle pattern outperformed other patterns, exhibiting a 15.03% increase compared to concentric and 8.8% compared to hexagon infill. In nanocomposites, all showed higher compressive strength than the matrix. For PLA/1.0%CNTs, strength was 16.8%, and for PLA/2.0%CNTs, it reached 39.2%. In honeycomb shapes with infill variations, the triangular pattern excelled with a 0.97% increase over concentric and 6.12% over hexagon patterns. Honeycomb results indicate a 59.6% increase for (PLA/1.0%CNTs) and a 0.48% increase for (PLA/2.0%CNTs) compared to the matrix. This study highlights 3D printing parameters, emphasizing the effectiveness of the triangular pattern and the enhanced strength with the addition of CNTs, providing insights to enhance products manufactured through Additive Manufacturing.

Curcumin, a polyphenol with a rich history spanning two centuries, has emerged as a promising therapeutic agent targeting multiple signaling pathways and exhibiting cellular-level activities that contribute to its diverse health benefits. Extensive preclinical and clinical studies have demonstrated its ability to enhance the therapeutic potential of various bioactive compounds. While its reported therapeutic advantages are manifold, predominantly attributed to its antioxidant and anti-inflammatory properties, its efficacy is hindered by poor bioavailability stemming from inadequate absorption, rapid metabolism, and elimination. To address this challenge, nano-delivery systems have emerged as a promising approach, offering enhanced solubility, biocompatibility, and therapeutic effects for curcumin. We have analyzed the knowledge on curcumin nano-encapsulation and its synergistic effects with other compounds, extracted from electronic databases. We discuss the pharmacokinetic profile of curcumin, current advancements in nano-encapsulation techniques, and the combined effects of curcumin with other agents across various disorders. By unifying existing knowledge, this analysis intends to provide insights into the potential of nano-encapsulation technologies to overcome constraints associated with curcumin treatments, emphasizing the importance of combinatorial approaches in improving therapeutic efficacy. Finally, this compilation of study data aims to inform and inspire future research into encapsulating drugs with poor pharmacokinetic characteristics and investigating innovative drug combinations to improve bioavailability and therapeutic outcomes.

The rapid development of electrochemical CO2 reduction offers a promising route to convert in-termittent renewable energy into products of high value-added fuels or chemical feedstocks. However, low faradaic efficiency, low current density, and a narrow potential range still limited the large-scale application of CO2RR electrocatalyst. Herein, monolith 3D bi-continuous nano-porous Bismuth (np-Bi) electrodes are fabricated via a simple one-step electrochemical dealloying strategy from Pb-Bi binary alloy. The unique bi-continuous porous structure ensures highly effective charge transfer, meanwhile the controllable millimeter-size geometric porous structure enables easy catalyst adjustment to expose highly suitable surface curvatures with abundant reactive sites. This results in a high selectivity of 92.6% and superior potential window (400 mV, selectivity >88%) for electrochemical reduction of carbon dioxide to formate. Our scalable strategy provides a feasible pathway for mass-producing high-performance and versatile CO2 electrocatalysts.

Weight loss solutions are on the rise, and there is growing interest in natural alternatives to the pharmaceuticals in the market, which are not devoid of relevant side effects. To this end, the objective of the current study is to assess the effects of a botanical-based blend comprised of lemon verbena and hibiscus extracts in weight management, body fat, appetite, lipid, and glucose profiles, in an overweight population, for 90 days. As a result, the volunteers presented significant weight loss in absence of diet, which coincided with decreased body fat. Body fat was assessed by anthropometry, electrical bioimpedance and DEXA scan. Cholesterol levels were also significantly decreased. Satiety assessment revealed that the product contributed to increased feeling of fullness and satisfaction after a meal, compared to the placebo group, which could contribute to the weight loss observed. Blood glucose and blood pressure levels remained unchanged, which was expected as the volunteers were normoglycemic and their blood pressure was in the healthy range. In conclusion, daily supplementation of a botanical-based blend contributes to weight loss in overweight individuals, in absence of diet, while not affecting other parameters that are in the healthy range. This product could be a candidate alternative or add-on to other weight loss products, as part of a healthy lifestyle.

Cancer, characterized by abnormal cell proliferation driven by genetic mutations, remains a significant health challenge. Tailoring effective therapies depends on factors like tumor location, grade, and stage, alongside patient condition. Leveraging Nano-carrier encapsulated drugs offers a promising avenue, as they accumulate preferentially at tumor sites, enhancing therapeutic efficacy while mitigating side effects. Polymeric Nano-carriers, with their customizable properties, further optimize drug delivery efficiency and specificity. Incorporating active targeting ligands such as antibodies, carbohydrates, peptides, folates, and aptamers-onto polymeric nanoparticle surfaces through techniques like functionalization, adsorption, and conjugation plays a pivotal role in directing therapeutic agents to tumor cells. Consequently, polymeric nanoparticles emerge as the carrier of choice for delivering drugs to various tumor types, including breast, colon, lung, prostate, liver, and spleen tumors.

With the development of organizational biology and forced from the EU Cosmetic Regulation (EU/1223/2009) with the complete ban of animal testing for cosmetic purposes, 3D skin models have been widely developed due to their similar physiological structure and metabolic function to native human tissue. 3D skin models for in vitro cosmetic evaluation are still promising alternative methods for evaluating phototoxicity, corrosivity and irritation. These models have been used for early screening and later validation of toxicity and efficacy evaluation by many well-known cosmetic companies. 3D skin models have become an important tool in cosmetic evaluation research. This article reviews the development of 3D skin models and their application in cosmetic evaluation. An outlook on the current application and future technological development directions in the cosmetic field is also presented.

Microscopic vision plays an important role in automated micro-assembly. However, some uncertain factors in the assembly process, such as occlusion and stains can lead to the mistakes of feature extraction. Herein, to solve the problem, the deep learning techniques are introduced into the feature recognition tasks, focusing on the attention mechanism and visualizing CNNs for DL-based microscopic vision. The main contributions are summarized as follows: The CBAM attention mechanism is combined with the YOLOv5 algorithm to improve the accuracy and robustness of feature extraction. The micropart feature occlusion experiment results show that at 70% occlusion degree, YOLOV5-CBAM can reach 97.9% [email protected], which is 4.6% higher than the original one. Visualization analysis of DL-based model is conducted using Grad-CAM to make the decision result more transparent and avoid potential visual detection risks during assembly. The heatmap matching degree between GT area and high-light area is increased by 27.81% on average, which further verify the effectiveness of attention mechanism in micropart feature localization. Additionally, micropart surface stain and droplet quality classification models based on ResNet50 are trained to replace the manual sorting. The visual results are consistent with human eye discernment and judgement, confirming the reliability of parts and droplets sorting.

Supermedia streams transfer video, audio, haptic and other sensory data. Real -time transfering of supermedia streams over the Internet is quite challenging. This paper outlines the proposed protocols for transferring supermedia streams over the Internet. Moreover, it describes the Quality of Service (QoS) requirements for supermedia applications that a network has to fulfill. Extensive simulations and experiments for the performance evaluation of transport protocols for real time transferring HEVC streams with supermedia data are carried out. Complements, differences and relevancies between simulation and real world experiments are discussed. The metrics that are measured for the performance evaluation are delay, jitter, throughput, efficiency, packet loss and one proposed by the authors, packet arrival deviation. The simulation tests reveal which protocols could be used for the transfer of real-time supermedia data with a HEVC video stream.

Magnesium ions play an important immune-regulatory role during bone repair. For this study, we prepared micro-nano bioactive glass containing magnesium, which can release magnesium, silicon, and calcium ions and has a positive impact on osteogenic differentiation and vascular regeneration. In this study, MgMNBG was compounded and combined with PLGA and PCL for 3D printing. Afterwards, the physicochemical properties and bone repair performance of the scaffolds were evaluated through in vitro and in vivo experiments. We also investigated the effects of MgMNBG on osteogenic differentiation, immune regulation, and vascular regeneration. The results showed that MgMNBG can inhibit inflammation and promote osteogenesis and angiogenesis by regulating macrophages. PLGA/PCL/MgMNBG scaffolds have good osteogenic and angiogenic effects, and the composite scaffolds have excellent bone repair performance and potential application value.

The assortment of low-cost 3D printers for “in-practice” use, e.g., for clear aligner therapies, is ever increasing. To address concerns about the accuracy of orthodontic models produced on such printers when cost efficient modes of 3D printing are employed, this study examined the effect of print model body type and print angulation on accuracy. Six printing-configuration groups were included: 2 model types (solid or hollow shell) combined with 3 print angles (0°, 70°, or 90°) with 10 models/group; all models were printed with 100-µm layer thickness using a digital light processing-based 3-dimensional printer. Eleven selected structures and distances were measured on the printed models with a digital microscope and compared to the same measures on a digitized master model. The clinically-acceptability range was set at ±0.25 mm difference from the master model for single tooth measurements (intra-tooth) and ±0.5 mm for cross-arch measurements (inter-tooth). For individual measurements across all models, 98% fell within clinical acceptability. For mean measurements within each model group, only canine height for the shell-0° model had a mean difference (0.26 mm ± 0.03) outside the clinically acceptable range for intra-tooth measurements. Standard deviations for all intra-tooth measurements were within 0.07 mm. While none of the mean inter-tooth measurements exceeded the acceptability range, the standard deviations were larger (0.04 to 0.30 mm). Accuracy of orthodontic models for clear aligner therapies was not impacted beyond the clinically acceptable range when altering model body type and print angulation to improve efficiency of 3D printing. These findings suggest greater flexibility of the practitioner to alter print settings to address time and cost efficiency in various clinical scenarios and still maintain clinically acceptable model accuracy.

This paper describes a novel concept of producing energy efficient ”Maroon enriched natural gas “ and then Pink hydrogen” from any hydrocarbon base. The key idea is the extraction of hydrogen from water in addition to that from the hydrocarbon in an optimal fashion. This has the benefit of higher water vapor to CO2 exhaust ratio than conventional carbonaceous fuels when generating energy via combustion, a prudent step in achieving Netzero goals in a shorter time, and creating energy independence in most places.. The process of production makes concentrated CO₂ available for use and or sequestration. The process also maximizes use of renewable electricity in hydrogen generation, and maximizes use of existing infrastructure, with a minimum capital cost by energy recycle in the process. The process design applies sound thermodynamic principles which evolved during the nineteenth century, and mimics the geochemical processes going on in some of the natural 'colorless hydrogen'.

Background: Thoracic endovascular aortic repair (TEVAR) has become the standard treatment for blunt thoracic aortic injury (BTAI). Some small observational studies revealed aortic morphological changes after TEVAR in patients with BTAI. However, these studies were limited by the rarity of the condition and small sample sizes. To address this gap, the current study aims to conduct a systematic review and meta-analysis of existing literature to provide evidence on the degree of immediate and long-term aortic diameter change following TEVAR for BTAI. Methods: This systematic review and meta-analysis of studies published up to March 2023, was conducted in accordance with the PRISMA statement. Studies eligible for inclusion were studies evaluating aortic diameter change post-TEVAR in BTAI patients. Results: 14 articles, including 353 patients, were included after review. Treatment and measurement protocols varied among individual studies resulting in high heterogeneity of the results. Our meta-analysis demonstrated an immediate post-intervention dilation 2.41 mm and 2.63 mm of the proximal and distal aortic necks’, respectively, as well as continuous dilation of the respective regions at a rate of 0.35 mm/year and 0.49 mm/year. Conclusion: TEVAR in BTAI leads to immediate post-intervention and continuous aortic dilation and morphological changes with possible future important clinical consequences.

In this study, the impact of the addition of high-aspect-ratio nano-ettringite to photocurable epoxy acrylate resin was explored, with a specific focus on the changes observed in viscosity, shrinkage, tensile strength, and elongation at the break of composites formed. Herein, the nano-ettringite samples were modified using KH-570. The 3 wt% or 6 wt% KH-570-modified and unmodified nano-ettringite were dispersed into the resin by ultrasonic treatment in conjunction with mechanical stirring. The grafting effects of nano-ettringite onto KH-570 were analyzed through scanning electron microscopy (SEM), X-ray diffraction (XRD), thermogravimetric (TG) analysis, and Fourier transform infrared spectroscopy (FTIR). The results demonstrate that increased dosages of unmodified and modified nano-ettringite led to increased viscosity of the composite while reducing shrinkage. At the same dosage, the photocurable resin with modified nano-ettringite demonstrated a lower shrinkage and a higher tensile strength. Notably, when the amount of modified nano-ettringite was 3 wt%, the highest tensile strength of the composite was 64.61 MPa, presenting a 72.57% increase compared to the blank sample. Furthermore, the incorporation of modified nano-ettringite as a filler provides a new perspective for improving the performance of photocurable epoxy acrylate resin composites.

This letter presents a dual-frequency terahertz amplitude modulator based on a cross-shaped structure and U-shaped metal patches. Its structural unit is a typical metal-substrate structure. The top metal consists of a cross-shaped structure and U-shaped metal patches, and the bottom substrate layer is made of quartz. Amplitude modulation is achieved by adjusting the temperature of the vanadium dioxide (VO2) patches. The modulation depth can be approximately 75%. The mechanism of the resonance frequency is explained by the equivalent circuit model. The proposed structure shows good amplitude modulation capability at different incidence and azimuth angles by changing the location of the VO2 patches. The dual-frequency terahertz amplitude modulator can be used in terahertz communication, imaging, etc.

GaN ultraviolet photodetector with metal-semiconductor-metal structure is achieved by growing on a periodic trapezoid column-shape patterned sapphire substrate using metalorganic chemical vapor deposition. Under 5-V reverse bias, the photodetector fabricated on such patterned sapphire substrate exhibits a lower dark current, a higher photocurrent, and a 476 % enhancement in the maximum responsivity as compare with those of the photodetector fabricated on conventional flat sapphire substrate. It is also found that the much larger UV-to-visible rejection ratio and the fact that responsivity drops in a smaller cut-off region are observed from photodetector fabricated by using a periodic trapezoid column-shape patterned sapphire substrate. These phenomena may all be attributed to the reduction of threading dislocation density and the improved quality of GaN film, as well as the internal reflection and/or scattering effect on the interface between GaN film and the periodic trapezoid column-shape pattern of the substrate.

Innovative tissue engineering biomimetic hydrogels based on hydrophilic polymers have been investigated for their physical and mechanical properties. 5% to 25% by volume loading PHEMA-nanosilica glassy hybrid samples were equilibrated at 37°C in aqueous physiological isotonic and hypotonic saline solutions (0.15 and 0.05 M NaCl) simulating two limiting possible compositions of physiological extracellular fluids. The glassy and hydrated hybrid materials were characterized both for dynamo-mechanical properties and equilibrium absorptions in the two physiological-like aqueous solutions. Mechanical and the morphological modifications occurring in the samples have been described. The 5% volume nanosilica loading hybrid nanocomposite composition showed mechanical characteristics in the dry and hydrated states that were comparable to those of cortical bone and articular cartilage, respectively, and then chosen for further sorption kinetics characterization. Sorption and swelling kinetics were monitored up to equilibrium. Changes in water activities and osmotic pressures in the water-hybrid systems equilibrated at the two limiting solute molarities of the physiological solutions have been related to the observed anomalous sorption modes using the Flory-Huggins interaction parameter approach. The bulk modulus of the dry and glassy PHEMA-5% nanosilica hybrid at 37°C has been observed to be comparable with the values of the osmotic pressures generated from the sorption of isotonic and hypotonic solutions. The anomalous sorption modes and swelling rates are coherent with the difference between osmotic swelling pressures and hybrid glassy nano-composite bulk modulus: the lower the differences the higher the swelling rate and equilibrium solution uptakes. Bone tissue engineering benefits of use of tuneable biomimetic scaffold biomaterials that can be “designed” to act as biocompatible and biomechanically active hybrid interfaces are discussed.

.Various synthetic nematicides are currently used effectively in the control of plant parasitic nematodes. However, these nematicides have adverse effects on humans and the environment. Neem oil is eco-friendly alternatives to synthetic nematicides. The effectiveness of repeated neem oil application in suppressing the root-knot nematodes infestation in figs seedlings was therefore examined in this study, both in its natural form (10 ml/L) and in its nano-emulsion form (5 and 7 ml/L). The recorded reduction parameters of M. incognita were J2/250g soil, galls and egg masses / 5g roots of infected fig seedlings were measured at that time, and the effects of these natural additives were compared with the Fosthiazate (Krenkel 75%EC). The impact of such soil amendments on some typical plant parameters, the total microbial count of soil, and the overall enzymatic activity of the fig rhizosphere were also included. Obtained results revealed that the soil population density of root knot nematode suppressed by 80.3% , reduction of nematode egg masses (60.4%) due to the application of nano-emulsion of neem oil (at 7ml/L). Present work recommend the use of nano-emulsion of neem oil as one of the effective and eco-friendly means to reduce the root- knot nematode on fig .

A new class of nano-cube core-shell heterostructures containing Ag coating on the top of WO₃ was fabricated. Physical vapor deposition was used to produce WO₃ based nano-heterostructures. All kind of wet toxic chemical process was avoided to make the process simple and contaminant free. Sputtering of WO₃ and a subsequent thermal annealing process was done to create nano-cubes of WO₃. After that, sputtering of Ag was performed to form the Ag-WO₃ core-shell nano-heterostructures (CSNH). The CSNHs were characterized using field emission scanning electron microscopy (FESEM), energy dispersive spectroscopy (EDS), X-ray diffraction analysis (XRD) and UV-vis spectroscopy. The morphologies, elemental analysis, interfaces, crystallinity, phases, and chemical compositions were analyzed. The bottom-up growth of WO₃ nanocubes was studied using different time periods at 900°C. Ag coating was also studied before and after annealing. Finally, an optical property (band gap) was also analyzed using Tauc plot derive from absorption spectra. The tailoring the band gap of WO₃ from ~2.9eV to ~ 2.45 eV was observed while Ag-WO₃ CSNH formed.

A brain-computer interface for controlling elements commonly used at home is presented in this paper. It includes the electroencephalography device needed to acquire signals associated to the brain activity, the algorithms for artefact reduction and event classification, and the communication protocol.

Two antimicrobial agents such as silver nanoparticles (AgNPs) and titanium dioxide (TiO2) have been formulated with natural polysaccharides (chitosan or alginate) to develop innovative inks for the rapid, customizable, and extremely accurate manufacturing of 3D printed scaffolds useful as dressings in the treatment of infected skin wounds. Suitable chemical-physical properties for the applicability of these innovative devices were demonstrated through the evaluation of water content (88-93%), mechanical strength (Young’s modulus 0.23-0.6 MPa), elasticity, and morphology. The antimicrobial tests performed against Staphylococcus Aureus and Pseudomonas Aeruginosa demonstrated the antimicrobial activities against Gram+ and Gram– bacteria of AgNPs and TiO2 agents embedded in the CH or ALG macroporous 3D hydrogels (AgNPs MIC starting from 5 µg/ml). The biocompatibility of chitosan was widely demonstrated by cell viability tests and was higher than that observed for alginate. Constructs containing AgNPs at 10 µg/ml concentration level did not significantly alter cell viability as well as the presence of titanium dioxide; cytotoxicity towards human fibroblasts was observed starting with AgNPs concentration of 100 µg/ml. In conclusions, the 3D printed dressings here developed own the features to be cheap, highly defined, easy to be manufactured and further applied in personalized antimicrobial medicine applications.

Aiming at effectively generating safe and reliable motion paths for quadruped robots, a hierar-chical path planning approach driven by dynamic 3D point cloud is proposed in this article. The developed path planning model is essentially constituted of two layers: global path planning layer and local path planning layer. At the global path planning layer, a new method is proposed for calculating terrain potential field based on point cloud height segmentation. Variable step size is employed to improve the path smoothness. At the local path planning layer, a real-time prediction method for potential collision area and a strategy for temporary target point selection is developed. Quadruped robot experiments were carried out in an outdoor complex environment. The experi-mental results verified that, for global path planning, the smoothness of the path is improved and the complexity of the passing ground is reduced. The effective step size is increased by a maxi-mum of 13.4 times, and the number of iterations is decreased by up to 1/6, compared with the traditional fixed step size planning algorithm. For local path planning, the path length is short-ened by 20%, more efficient dynamic obstacle avoidance and more stable velocity planning are achieved by using the improved dynamic window approach (DWA).

Recent progress in the fabricating flexible electronics has been developed significantly due to the increased interest of the flexible electronics which can be applied to enormous fields not only to conventional electronic devices but to bio/eco electronic devices. Flexible electronics can be applied to wide range of fields such as flexible display, flexible power storage, flexible solar cells, wearable electronics and healthcare monitoring devices. Recently, flexible electronics are being attached on the skin and even implanted into human body to monitor the bio-signals and for treatment purpose. To improve the electrical characteristic and the mechanical properties of flexible electronics, nanoscale fabrications using novel nano-materials are required. Advanced in nanoscale fabrication methods allow construction of the active materials that can combine with the ultra-thin soft substrate to form flexible electronics with high performances and reliability. In this review, wide range of nanoscale fabrication methods for flexible electronics classified in either top-down or bottom-up approaches such as conventional photolithography, soft lithography, nanoimprint lithography, growth, assembly and chemical vapor deposition(CVD) will be reported with specific fabrication processes and results. Here, our aim is to introduce various fabrication methods that can be used to fabricate the flexible electronics.

We report on a new form of nanoscale carbon nitride in the shape of single layer half dome structures grown on the step edges of boron nitride sheets. The half dome structure grown on the step edges of boron nitride sheets. The half dome structures are formed spontaneously at high temperature using Iron oxide nanoparticles capped with tetremethylammonium hydroxide supported on BN sheets. During the combustion process the support, firstly, acted as a reducing agent, secondly, as a source of nitrogen that permitted the transformation of the organic capping agent in sp1 CN chains linked with sp2 CN domains. During the Ostwald ripening process smaller nanoparticles migrates towards bigger nanoparticles, when the nanoparticles come across the step edges of few layer boron nitride sheets the half dome structure is formed. This new method of synthesis has demonstrated for the first time the formation of half dome structures containing cyanopolyynes sp1 chains and sp2 carbon nitride domains.

Nano-drugs and nano-delivery systems are rapidly evolving, with new strategies emerging in the current practices. The evolution of these technologies began with modifying the chemical structure, progressing to supramolecular ionic complexes, and culminating in elegant ad hoc delivery systems. Nanoparticles have numerous benefits as a carrier system for delivering therapeutic agents to intra-arterial sites. These benefits include their subcellular size, targeted surfaces, good suspensibility, and uniform dispersity, making them an ideal choice for catheter-based delivery. Despite the advancements made in the field of nano-drugs and nano-delivery systems, there are still some hurdles to overcome in terms of their commercial availability.The current review presents an updated summary of recent advancements in nano-drugs and nano-delivery systems, including their commercial availability. We aim to discuss the present challenges and prospects of commercially available nano-drugs and nano-delivery systems. Here, we provide a precise and informative overview of the current state of these technologies and underscore the potential they hold for future developments. Further, we have categorized commercially available modifications, name, parent company and their main applications in nano-drugs.

Pedestrian Dead Reckoning (PDR) is a promising algorithm for indoor positioning. However, the accuracy of PDR degrades due to the accumulated error, especially in multi-floor buildings. This paper introduces a three-dimensional (3D) positioning method based on terrain feature matching to reduce the influence of accumulated error in multi-floor scene. The proposed method involves two steps: motion pattern recognition and position matching calibration. The motion pattern recognition aims to detect different motion states, i.e., taking the stairs or horizontal walking, from the streaming data. Then, stair entrances and corridor corners are matched with transition points of motion states and pedestrian turning points, respectively. After matching, calibration is performed to eliminate the accumulated errors. By carrying out experiments on a two-floor closed-loop path with a walking distance about 145 m, it is shown that this method can effectively reduce the accumulated error of PDR , achieving accurate 3D positioning . The average error is reduced from 6.60 m to 1.83 m.

Recent advances in recording and real-time analysis of surface electromyographic signals (sEMG) have fostered the use of sEMG human-machine interfaces for controlling personal computers, prostheses of upper limbs, and exoskeletons among others. Despite a relatively high mean performance, sEMG-interfaces still exhibit strong variance in the fidelity of gesture recognition among different users. Here we systematically study the latent factors determining the performance of sEMG-interfaces in synthetic tests and in an arcade game. We show that the degree of muscle cooperation and the amount of the body fatty tissue are the decisive factors in synthetic tests. Our data suggest that these factors can only be adjusted by a long-term training, which promotes fine-tuning of low-level neural circuits driving the muscles. A short-term training has no effect on synthetic tests, but significantly increases the game scoring. This implies that it works at a higher decision-making level, not relevant for synthetic gestures. We propose a procedure that enables quantification of the gestures’ fidelity in a dynamic gaming environment. For each individual subject the approach allows identifying “problematic” gestures that decrease gaming performance. This information can be used for optimizing the training strategy and for adapting the signal processing algorithms to individual users, which could be a way for a qualitative leap in the development of future sEMG-interfaces.

Tailings generated by mining account for the largest proportion of global waste from industrial activities. Copper is relatively uncommon world-wide, with low concentrations in sediments and waters, yet is very elevated around mining sites. On the Keweenaw Peninsula of Michigan, USA, jutting out into Lake Superior, 140 mines extracted native copper from the Portage Lake Volcanic Series, part of an intercontinental rift system. Between 1901-1932, two mills at Gay (Mohawk, Wolverine) sluiced 22.7 million metric tonnes (MMT) of copper-rich tailings (stamp sands) into Grand (Big) Traverse Bay. Here we examine: 1) 3D coastal elevation and reef bathymetry, 2) particle dispersal, 3) copper concentrations and leaching, plus 4) shoreline toxicity. About 10 MMT of tailings created a migrating coastal beach that stretches 7 km from the Gay pile to the Traverse River Seawall. Another 10 MMT are moving underwater on the coastal shelf, threatening Buffalo Reef, an important lake trout and whitefish breeding ground. Aerial photos, ALS (plane) LiDAR, and relatively inexpensive UAS (drone) surveys characterize shoreline structure and aid initial remediation. Because sands (natural beach quartz, stamp sand basalt) are silicates of similar density, particle dispersal is similar and challenging. However, stamp sand beaches contrast greatly with natural sand beaches in both physical profile and chemistry. Dispersing particles retain copper, and release toxic concentrations. Leaching is elevated by exposure to high DOC and low pH waters. Field experiments, shoreline seining, and benthic sampling confirm serious impacts on aquatic biota, supporting tailings removal.

The awareness of the existence in plants of bioactive compounds namely phytochemicals (PHYs), having health properties is progressively expanding. Therefore, their massive introduction in the normal diet, in food supplements, and their use as natural therapeutics to treat several diseases are increasingly emphasized by several sectors. Particularly, most PHYs possessing antifungal, antiviral, anti-inflammatory, antibacterial, antiulcer, anti-cholesterol, hypoglycemic, immunomodulatory, and antioxidant properties have been isolated from plants. Additionally, their secondary modification with new functionalities, to further improve their intrinsic beneficial effects, is extensively investigated. Unfortunately, although the idea of exploiting PHYs as therapeutics is amazing, its realization is far from simple, and the possibility of exploiting them as effective orally administrable drugs is almost utopic. Most PHYs are insoluble in water and, when introduced orally, they scarcely reach the site of action in therapeutic concentrations. Degradation by enzymatic and microbial digestion, occurring in the mouth, stomach, and intestine, as well as fast metabolism and rapid excretion via the kidney, biliary, or lung, strongly limit their in vivo activity. To overcome these drawbacks, several nanotechnological approaches have been used and many PHYs-loaded delivery systems with dimensions of nanometers have been developed. This paper, also by reporting various recent case studies, reviews the foremost nano-suspension and nano-emulsion-based techniques developed for formulating the most relevant PHYs in more bioavailable nanoparticles (NPs), suitable or promising for clinical application. Also, the acute and chronic toxic effects due to the exposure to NPs reported so far, the possible nanotoxicity which could derive by their massive employment, as well as the ongoing actions to improve the knowledge in the field were discussed. The state of the art concerning the actual clinical application of both PHYs and the nanotechnologically engineered PHYs was also reviewed.

Previous research demonstrates that the interruption of immersive experiences may lead to a bias in the results of questionnaires. Thus, the traditional way of presenting questionnaires, paper-based or web-based, may not be compatible with evaluating VR experiences. Recent research has shown the positive impact of embedding questionnaires contextually into the virtual environment. However, a comprehensive overview of the available VR questionnaire solutions is currently missing. Furthermore, no clear taxonomy exists for these different solutions in the literature. To address this, we present a literature review of VR questionnaire user interfaces (UI) following PRISMA guidelines. Our search returned 1.109 initial results, which were screened for eligibility, resulting in a corpus of 25 papers. This paper contributes to HCI and games research with a literature review of embedded questionnaires in VR, discussing the advantages and disadvantages and introducing a taxonomy of in-VR questionnaire UIs.

We present the results of a twofold experimental and computational study of (0001) GaN/AlN multilayers forming pseudomorphic superlattices. High-Resolution Transmission Electron Microscopy (HRTEM) shows that heterostructures with GaN Quantum Wells (QW) four c-lattice parameters thick are misfit-dislocation free. Accurate structural data are extracted from HRTEM images via a new methodology optimizing the residual elastic energy stored in the samples. Total energy calculations are performed with several models analogous to the experimental QWs with increasing thicknesses of GaN, whereas this of the AlN barrier is kept fixed at n=8 c-lattice parameters. With vanishing external stresses, minimum energy configurations of the studied systems correspond to different strain states. Linear elasticity accurately yields the corresponding lattice parameters, suppressing the need for on-purpose total energy calculations. Theoretically justified parabolic fits of the excess interfacial energy yield the values of interfacial stress and elastic stiffness as functions of the GaN QW thickness. Total species-projected densities of states and gap values extracted therefrom allow deciphering the effect of the evolving strain on the electronic structure of the superlattice. It is found that the gap energy decreases linearly with increasing the strain of the QW. These results are briefly discussed in the light shed by previous works from the literature.

Multimodal user interfaces promise a natural and intuitive human machine interactions. But is the extra effort for the development of a complex multi-sensor system justified, or can users also be satisfied with one input modality already? This study investigates interactions in an industrial weld inspection workstation. Three unimodal interfaces, including spatial interaction with buttons augmented on a workpiece or a worktable, and speech commands, were tested individually and in a multimodal combination. Within the unimodal conditions, users preferred the augmented worktable, but overall, the interindividual usage of all input technologies in the multimodal condition was ranked best. Our findings indicate that the implementation and use of multiple input modalities is valuable, and that it is difficult to predict the usability of individual input modalities for complex systems.

One of the modern methods of improving operating characteristics of titanium and titanium-based alloys under conditions of friction and increased contact loads is the method of ion-plasma nitriding. The effect of nitriding of VT5 alloy (Al 4,5-6,7 %, V to 1,2 %, Mo to 0,8 % − analogue 3.7115) in the plasma of a glow discharge excited in a hollow cathode on its tribological characteristics in pairs with different materials in T-1 fuel and under dry friction conditions has been studied. For research and tribological tests, samples of VT5 alloy were nitrided in the plasma of a glow discharge excited in a hollow cathode at a temperature of 975 ± 15°C and a pressure of 58 ± 2 PA in a nitrogen-argon gas mixture with a nitrogen content of 78 %. Studies of samples of VT5 alloy after nitriding showed that the surface roughness Ra was in the range of 0.58-0.64, and the surface hardness HV5 was 525 ± 20 kgf/mm² at a base hardness of 325 ± 15 kgf/mm². Tribological tests were performed on a friction machine 2070 SMT-1 according to the scheme "cube - roller". Tests under conditions of friction with oil were performed at a load of 200 N. The sliding speed during the tests was 1.3 m/s, the test time was 75 sec. The test under dry friction conditions was carried out at a load of 100 N and a sliding speed of 0.785 m/s, the test time was 30 minutes. Low wear ability in relation to the nitrided titanium alloy VT5 (<2.4x10^-4 mm³/s), as well as friction coefficients at the level of 0.08 to 0.12 in the order of their growth had bronze VB-23NTS (Pd 18–22 %, Ni 3–4 %, Zn 3–4 %, Sb 3–4 %, P 0.15–0.3) r.O10C2N3, VB-24 (Sb 4.7–6, 2 %, P 0.4–0.9), steel 1.3505, cast iron GGG80, cemented steel 20Cr3MoWV.

The beneficial effects of Lanthanide incorporation into 0.94Na0.5Bi0.5TiO3-0.06BaTiO3 (BNT-BT) matrix on its functional properties were investigated. The conventional solid-state method was used for synthesizing samples. The structural refinement revealed that all samples crystallized in R3c rhombohedral symmetry. Raman spectroscopy study was carried out using green laser excitation and revealed that no clear perceptible variation in frequency is observed. Dielectric measurements unveiled that the introduction of rare earth obstructed the depolarization temperature promoted in BNT-BT with decreasing the diffusive phase transition with increasing the lanthanide size. Only Dysprosium addition showed comparable diffusion constant and dielectric behavior as the unmodified composition. Further, the comparison of the obtained ferroelectric hysteresis and strain-electric field loops revealed that only Dy-phase exhibited interesting properties comparing parent composition. In addition, the incorporation of lanthanides Ln3+ into the BNT-BT matrix led to the development of luminescence characteristics in the visible and near infrared regions, depending on the excitation wavelengths. The simultaneous occurrence of photoluminescence and ferroelectric/piezoelectric properties opens up possibilities for BNT-BT-Ln to exhibit multifunctionality in a wide range of applications.Keywords: Sodium Bismuth Titanate; structural refinement; dielectric properties; ferroelectric properties; piezoelectric properties; Photoluminescence.

Graphene is perhaps the most prominent “Dirac material,” a class of systems whose electronic structure gives rise to charge carriers that behave as relativistic fermions. In multilayer graphene several crystal sheets are stacked such that the honeycomb lattice of each layer is displaced along one of the lattice edges. When subject to an external magnetic field, the scaling of the multilayer energy spectrum with the magnetic field, and thus the system’s thermodynamic behavior, depends strongly on the number of layers. With this in mind, we examine the performance of a finite-time endoreversible Otto cycle with multilayer graphene as its working medium. We show that there exists a simple relationship between the engine efficiency and the number of layers, and that the efficiency at maximum power can exceed that of a classical endoreversible Otto cycle.

Many real complex systems present multilayer structure where high-order metadata on one layer refers to dyadic data on a lower layer. Significant progresses to analyse high-order metadata under the assumption of community organization have been done. However, there are no planted communities in real-world networks, and the necessity of new frameworks to analyze high-order metadata regardless of community organization has been raised.Here, we propose to adopt hyperedge organization. Predicting ‘entanglements’ between a hyperedge and nodes scattered in the rest of the network might suggest structural or functional liaisons, without assumption of any community organization. We introduce a novel concept: hyperedge entanglement (HE), which associates to each hyperedge an entangled hyperedge, by means of a network operator that predicts significant ‘interactions at distance’ between network nodes and existing hyperedges. We also introduce a new challenge termed hyperedge entanglement prediction (HEP), and an algorithm to perform this task. We evaluated HEP performance on social, biological and synthetic data where, given only topology and hyperedges (such as communities or functional modules), the goal is to predict whether nodes not connected to a certain hyperedge might be candidates for a significant entanglement. Finally, as real application in diseasome systems biomedicine, we perform HEP on the human protein interactome to predict unknown gene entanglements with the COPD disease gene hyperedge. HEP predictions are validated by biological experiments, enlarging our understanding of molecular mechanisms behind COPD/aneurysm comorbidity.

Existing research indicates that mineralization of Carlin-type gold deposit is related to geological structures, but current studies mostly focus on the qualitative association, and lack quantitative analysis of the relationship between mineralization and structural features, which limits the potential for predictive mineral exploration. In this study, the Nibao Carlin-type gold deposit was selected as the research area to conduct three-dimensional geological modeling, spatial analysis, and three-dimensional prospectivity modeling. Spatial analysis revealed that the majority of gold ore bodies are situated near the main fault, with gold mineralization primarily occurring within a spatial range of approximately -80 meters to 20 meters from the main fault plane. This spatial distribution predominantly aligns in a SW-NE direction. Spatial characteristic extraction of fault slope indicators suggests that the slope angles are conducive to the migration and accumulation of ore-forming hydrothermal fluids, with ore body metal content rapidly increasing within an angle range of approximately 20° to 60°. The shape analysis of the mainfault indicates that the principal spaces of mineralization enrichment are within -10m to 20m of the fault plane undulations, where gold resources are concentrated in a relatively flat area. However, the degree of mineralization is more pronounced in the protruding sections than in the depressed areas. The areas with significant dip changes in faults display higher variations in orebody attitudes, with mineralization noticeably weaker in areas where the fault steepness changes markedly. Ore-bearing units exhibit significantly higher grades within the -17° to 3° interval of fault steepness transition. This interval also sees a rapid accumulation of gold resources. The Nibao gold mine's mineralization is derived from deep, ore-bearing hydrothermal fluids ascending along major fractures, precipitating, and accumulating in favorable ore-hosting spaces (faults, anticline cores) and lithological combinations (sedimentary tuffs, tuffs). Three deep potential gold targets were identified, highlighting the deep western edge of the F1 fault and the deep southeast-trending lower plate as prospective areas for future exploration. This study underscores the effectiveness of 3D prospective modeling as an indispensable tool for elucidating the spatial distribution of fault-controlled Carlin-type gold deposits and their tectonic determinants.

In this communication the concept of functional materials is understood such as real modified substrates for nanomedicine applications. Functional and modified substrates focused on microcapsules and devices for new nanomedicine diagnosis and treatments. Cases of different materials are shown to support the functionality strategy, as in particular chemicals, pharmacophores, and controlled nano-chemistry for the design of nanoplatforms. Recent studies have reported hybrid inorganic/organic compositions for biocompatible, biodegradable, and support materials added to particular physical properties such as conductive, semiconductive, and high electromagnetic fields from the near field within the nanoscale to far-field applications and new nano-pharmacophores and nanomedicine therapeutics. New approaches are shown from the nano-scale to the micro- and higher sizes of substrates for improved therapeutic strategies. Micro-capsules for biosensing and drug delivery applications were developed. In addition, we report recent and novel research centered on implantable, portable, and wearable devices applied to future treatments.

Atopic dermatitis (AD) is a chronic inflammatory disorder presenting a dysregulated immune response and derangement of the epidermal barrier lipids. The Th2-type cytokines interleukin IL-4 and IL-13 play a prominent role in AD by activating the Janus Kinase/Signal Transduction and Activator of Transcription (JAK/STAT) intracellular signal axis. This study aimed to investigate the role of JAK/STAT in the lipid perturbations induced by Th2 signaling in 3D-epidermal equivalents. We used tofacitinib, a low-molecular-mass JAK inhibitor, to screen for the JAK/STAT-mediated deregulation of lipid metabolism. Th2 cytokines decreased the expression of elongases 1, 3, and 4, and serine-palmitoyl-transferase and increased that of sphingolipid delta(4)-desaturase, and carbonic anhydrase 2. Th2 cytokines inhibited the synthesis of palmitate and caused a depletion of triglycerides. This depletion was associated with altered PC profiles and fatty acid (FA) metabolism. Overall, the ceramide profiles were minimally affected. Except for most sphingolipids and very long chain FAs, the effects of Th2 on lipid pathways were reversed by co-treatment with tofacitinib. An increase in the mRNA levels of CPT1A and ACAT1, reduced by tofacitinib, suggests that Th2 cytokines promote FA beta-oxidation. In conclusion, pharmacological inhibition of JAK/STAT activation prevents the lipid disruption caused by halted homeostasis of FA metabolism.

Background: Prostate cancer (PCa) is characterized by significant heterogeneity in its molecular, genomic, and immunologic characteristics. Methods: Whole transcriptome RNAseq data from The Cancer Genome Atlas of prostate adenocarcinomas (n=496) was utilized. The immune microenvironment was characterized using the CIBERSORTX tool to identify immune cell type composition. Unsupervised hierarchical clustering was performed based on immune cell type content. Analyses of progression-free survival (PFS), distant metastases, and overall survival (OS) were performed using Kaplan-Meier estimates and Cox-regression multivariable analyses. Results: Four immune clusters were identified, largely defined by plasma cell, CD4+ Memory Resting T Cells (CD4 MR), M0 and M2 macrophage content (CD4 MRHighPlasma CellHighM0LowM2Low, CD4 MRLowPlasma CellHighM0LowM2Low, CD4 MRHighPlasma CellLowM0HighM2Low, and CD4 MRHighPlasma CellLowM0LowM2High). The two macrophage-enriched/plasma cell non-enriched clusters (3&4) demonstrated worse PFS (HR 2.24, 95% CI 1.46–3.45, p=0.0002) than the clusters 1&2. No metastatic events occurred in the non-macrophage-enriched clusters. Comparing clusters 3 vs 4, in patients treated by surgery alone, cluster 3 had zero progression events (p<0.0001). However, cluster 3 patients had worse outcomes after post-operative radiotherapy (p=0.018). Conclusion: Distinct tumor immune clusters with a macrophage-enriched phenotype and reduced plasma cell enrichment independently characterize an aggressive phenotype in localized prostate cancer that may differentially respond to treatment.

Although Darwin‘s evolutionary mutation theory has been widely accepted, many endeavors have been tried to challenge it. With more and more observation of successful hybridization and hybrids, the sexual isolation between species has become vague. The mechanism of evolution has been expanded from the classical model of evolution to multiple routes of speciation. Furthermore, a fundamental crossbreeding theory has been raised and proved by two lines of evidences: paleopolyploidy and fan-shaped spectrum of species. Ancient genome duplications are widespread throughout eukaryotic lineages, particularly in plants. The genome polyploidization, especially in the somatic cell hybridization, can break through the sexual incompatibility between diploid counterparts to hybridize and produce new species. By comparing characteristics, all species in every taxon, both in the extinct fossil and extant organisms, can be arranged into fan-shaped spectrum according to their similarity: left primitive type-middle advanced type-right primitive type. The species are primitive at the two ends and advanced at the middle. The primitive two species always resemble two types of more primitive species that can be confirmed as their ancestors respectively, and the middle species is half similar to the two ancestors respectively. These suggest that the species in the spectrum come from two different ancestors by crossbreeding and gene combination. As a sum, advanced species originated from crossbreeding of two primitive ancestors, by major method of polyploidization, and proved by results of fan-shaped spectrum of species. Then, sex is the cause, force and opportunity for evolution.

Preventing the occurrence of secondary caries serves as one of the significant issues in dental clinic, thus make it indispensable to improving the properties of conventional composite resin (CR) by developing a novel CR. In present study, two groups of experimental CRs loaded with different contents of fluoride-doped nano-zirconia fillers (25 wt% and 50 wt%) were fabricated. The surface topography, mechanical performance, fluoride release, antibacterial effect, aging property and cytotoxicity of the experimental CRs were evaluated subsequently. A uniform distribution of the F-zirconia fillers over the whole surface of resin matrix could be observed. The experimental CRs showed continuous fluoride release within 28 days, which was positively correlated with the content of F-zirconia fillers. Moreover, the amount of fluoride release increased in the acidic buffer. Addition of F-zirconia fillers could improve the color stability, wear resistance and microhardness of the experimental CRs, without reducing the flexure strength. Furtherly, the fluoride ions released continuously from the experimental CRs resulted in effective contact and antibacterial properties, while they showed no cytotoxicity. As a consequence, considerations can be made to employ this new kind of composite resin loaded with fluoride-doped nano-zirconia fillers to meet clinical requirements when the antimicrobial benefits are desired.

Sustainable manufacturing practices are becoming increasingly necessary due to the growing concerns regarding climate change and resource scarcity. Consequently, material recycling technologies have gradually become preferred over conventional processes. This study aimed to recycle waste polylactic acid (PLA) from household-disposed cups and lids to create 3D-printed parts and promote sustainable manufacturing practices. To achieve this, the current study utilised virgin and post-consumer PLA (sourced from household waste) blends. The PC-PLA wastes were shredded and sorted by size with the aid of a washing step, resulting in a filament with a 1.70 ± 0.5 mm diameter without fragmentation or dissolution. A 50:50 wt.% blend of virgin PLA (vPLA) and PC-PLA was selected as the standard recycling percentage based on previous research and resource conservation goals. The study investigated the impact of three 3D printing parameters (layer height (LH), infill density (I), and nozzle temperature (NT))on the quality of 3D-printed parts using a three-level L9 Taguchi orthogonal array. The findings revealed that blending PC-PLA with vPLA led to significant improvements in the tensile, flexural, and impact strengths by 18.40%, 8%, and 9.15%, respectively, compared to those of recycled PLA. This conclusion was supported by the investigation of the fracture surface area, which revealed fractographic features associated with printing parameters, such as plastic deformation and interfilament debonding. An ANOVA analysis revealed a positive influence of larger layer height and high nozzle temperature on the mechanical properties. Subsequently, the optimal printing parameters (LH: 0.3 mm, I: 100%, and NT: 215 °C) were determined using the S/N ratio, and a confirmation test using the optimum printing parameters exhibited a strong correlation with statistically predicted outcomes. Finally, the study used optimum printing parameters to fabricate 100% post-consumer recycled PLA 3D printed parts, demonstrating their potential for low-strength applications. Based on these findings, it can be concluded that virgin and post-consumer recycled PLA blended filament for fabricating 3D printed components is an effective way to support plastic recycling in the context of a circular economy.

Objective: The aim of this in vitro study was to evaluate the accuracy of resin-based fixed dental restorations, namely veneers, single crowns, and four-unit fixed partial dental prosthesis (FPDs) using two different 3D printers and polymer-based materials. Materials and Methods: A standard maxillary polyurethane jaw model containing prepared teeth was scanned using an intraoral scanner. The generated STL data were used to design the restorations virtually using CAD software. Two 3D printers were utilized for the provisional digital light processing and stereolithography for the castable resin patterns. Each printer produced 10 specimens of each type of restoration, for a total of 80 restorations. The 3d-printed restorations were then 3D scanned using the same intraoral scanner and evaluated for external and internal dimensional accuracy in terms of trueness and precision. A one-way ANOVA and Two-sample T-Test were implemented to compute the precision (variability between groups) and trueness (with the designed CAD model). A level of statistical significance of p-Value

The environment impacts human health in profound ways, yet few theories define the form of the relationship between human physiology and the environment. Under current epidemiological constructs of causation, it is assumed that two complex systems (environment and humans) can transfer information directly. This is the underlying structure of the relationship when studies examine, for example, air pollution and brain health. In marked contrast, we conjecture that complex systems cannot interact directly, but rather such interaction requires the formation of an “interface”. Further, we contend that this dynamic, process-based interface incorporates components from all the interacting systems but exhibits operational independence. This property has many consequences, the foremost being that characteristics of the interface cannot be fully resolved by only studying the systems involved in the interaction. The interface itself must be the subject of inquiry. Without refocusing our attention on biodynamic interfaces, we cannot discern how our environment impacts health.

B chromosomes are supernumerary chromosomes which are found in addition to the normal standard chromosomes (A chromosomes). B chromosomes are well known to accumulate several types of repeats. Although the evolution of B chromosomes has been subject of numerous studies, the mechanisms of accumulation and evolution of repetitive sequences is not fully understood. Recently, new genomic approaches have shed light on the origin and accumulation of different classes of repetitive sequences in the process of B chromosome formation and evolution. Here we discuss the impact of repetitive sequences accumulation on the evolution of plant B chromosomes.

Objective: The aim of study is to find key genes and enriched pathways associated with lung cancer. Participants and Methods: Differentially expressed genes (DEGs) data of 54674 genes based on stage, tumor and status of lung cancer was taken from 66 patients of African American (AAs) origin. 2392 DEGs were found based on stage, 13502 DEGs were found based on tumor, 2927 DEGs were found based on status having p value (p<0.05). Results: Total 33 common DEGs were found from stage, tumor and status of lung cancer. Gene ontology (GO) and KEGG pathway enrichment analysis was performed and 49 significant pathways were obtained, out of which 10 pathways were found to be exclusively involved in lung cancer development. Protein-protein interaction (PPI) network analysis found 69 nodes and 324 edges and identified 10 hub genes based on their highest degrees. Module analysis of PPI found that ‘Viral carcinogenesis’, ‘pathways in cancer’, ‘notch signaling pathway’, ‘AMPK signaling pathways’ had a close association with lung cancer. Conclusion: These identified DEGs regulate other genes which play important role in growth of lung cancer. The key genes and enriched pathways identified can thus help in better identification and prediction of lung cancer.

The human mandible's cancellous bone, which is characterized by its unique porosity and directional sensitivity to external forces, is crucial for sustaining biting stress. Traditional CAD models fail to fully represent bone's anisotropic structure and thus depend on simple isotropic assumptions. For our research, we use the latest versions of nTopology and Creo Parametric software to make biomimetic Voronoi lattice models that accurately reflect the complex geometry and mechanical properties of trabecular bone. The porosity of human cancellous bone is accurately modeled in this work using biomimetic Voronoi lattice models. The porosities range from 70% to 95%, which can be achieved by changing the pore sizes to 1.0 mm, 1.5 mm, 2.0 mm, and 2.5 mm. Finite element analysis (FEA) was used to examine the displacements, stresses, and strains acting on dental implants with a buttress thread, abutment, retaining screw, and biting load surface. The results show that the Voronoi model accurately depicts the complex anatomy of the trabecular bone in the human jaw, compared to standard solid block models. The ideal pore size for biomimetic Voronoi lattice trabecular bone models is 2 mm, taking into account both the von Mises stress distribution over the dental implant, screw retention, cortical bone, cancellous bone, and micromotions. This pore size displayed balanced performance by successfully matching natural bone's mechanical characteristics. Advanced finite element analysis (FEA) improves biomechanical understanding of how bones and implants interact by creating more accurate models of biological problems and dynamic loading situations. This makes biomechanical engineering better.

The development of microelectronics is always driven by reducing transistor size and increasing integration, from the initial micron-scale to the current few nanometers. The photolithography technique for manufacturing the transistor needs to reduce the wavelength of the optical wave, from ultraviolet, deep, to the existing extreme ultraviolet light. One approach toward decreasing the working wavelength is using lithography based on beyond extreme ultraviolet radiation (BEUV) with a wavelength around 7 nm. The BEUV lithography relies on advanced reflective optics such as periodic multilayer film X-ray mirrors (PMMs). PMMs are artificial Bragg crystals having alternate layers of “light” and “heavy” materials. The periodicity of such a structure is relatively half of the working wavelength. Since a BEUV lithographical system contains at least 10 mirrors, optics’ reflectivity becomes a crucial point. The increasing of a single mirror's reflectivity by 10% will increase the system’s overall throughput by 6 times. In this work, the properties and development status of PMMs, particularly for BEUV lithography, were reviewed to gain a better understanding of their advantages and limitations. Emphasis was given to materials, design concepts, structure, deposition method, and optical characteristics of these coatings.

Over the years, network analysis became a promising strategy to analyze complex system, i.e. systems composed by a large number of interacting elements. In particular, multilayer networks have emerged as a powerful framework for modelling and analysing complex systems with multiple types of interactions. Network analysis can be applied to pharmacogenomics to gain insights into the interactions between genes, drugs, and diseases. By integrating network analysis techniques with pharmacogenomic data, the goal consists to uncover complex relationships and identify key genes to use in pathway enrichment analysis to figure out biological pathways involved in drug response and adverse reactions. In this study, we model omics, diseases and drugs data together through the multilayer network representation. Then, we mined the multilayer network with a community detection algorithm by obtaining top communities. After that, we used the identified list of genes from the communities to perform pathway enrichment analysis (PEA) to figure out the biological function affected form the selected genes. The results show that the genes forming the top community have the multiple roles through different pathways.

herein, we have compared the performance of SVM and MLP in emotion recognition using speech and song channels of the RAVDESS dataset. We have undertaken a journey to extract various audio features, identify optimal scaling strategy and hyperparameter for our models. To increase sample size, we have performed audio data augmentation and addressed data imbalance using SMOTE. Our data indicate that optimised SVM outperforms MLP with an accuracy of 82 compared to 75%. Following data augmentation, the performance of both algorithms was identical at ~79%, however, overfitting was evident for the SVM. Our final exploration indicated that the performance of both SVM and MLP were similar in which both resulted in lower accuracy for the speech channel compared to the song channel. Our findings suggest that both SVM and MLP are powerful classifiers for emotion recognition in a vocal-dependent manner.

In Nature, it is common for living plants and non-living plant tissues to consist of materials with anisotropic multilayer and non-homogenous structure. The structure of tissues determines their self-shaping and self-folding capabilities in response to a stimulus in order to activate different functionalities. Predetermined movements are realized according to changes in environmental conditions, which trigger the fibrous anisotropic structure of the plants’ material. In this study, we present the fabrication process of low-cost anisotropic multilayer materials that are capable of realizing complex movements caused by small temperature changes (<40 ^oC). The mismatch in the thermo-mechanical properties between three or more anisotropic thin layers creates responsive materials that alter their shape owing to the developed internal stresses. Isotropic layers can perform only bending movements, whereas anisotropic multilayer materials can perform bending, twisting or complex combined modes. The movements of the material can be controlled by forming anisotropic homogenous metallic strips over an anisotropic polymer. As a result, inexpensive responsive materials can be developed to passively react to a very broad range of thermal requirements. We studied the major parameters that affect the sensitivity of the developed materials, as well as their failure modes and crack formation under thermal fatigue conditions.

: Microplastics and nanoplastics (MNPs) are becoming an increasingly severe global problem due to their widespread distribution and complex impact on living organisms. Apart from their environmental impact, the effects of MNPs on living organisms have also continued to attract attention. The harmful impact of MNPs has been extensively documented in marine invertebrates and larger marine vertebrates like fish. However, the research on the toxicity of these particles on mammals is still limited, and their possible effects on humans are poorly understood. Considering that MNPs are commonly found in food or food packaging, humans are primarily exposed to them through ingestion. It would be valuable to investigate the potential harmful effects of these particles on gut health. This review focuses on recent research exploring the toxicological impacts of micro- and nanoplastics on the gut, as observed in human cell lines and mammalian models. Available data from various studies indicate that the accumulation of MNPs in mammalian models and human cells may result in adverse consequences, in terms of epithelial toxicity, immune toxicity, and disruption of gut microbiota. The paper also discusses the current research limitations and prospects in this field, aiming to provide a scientific basis and reference for further studies on the toxic mechanisms of micro- and nanoplastics.

Developing particles of different anisotropic shapes are the hot topic since decades as they guarantee some special features of properties not possible through other means. Again, controlling atoms to develop certain size and shape particle is a quite challenging job. In this study, gold particles of different shapes are developed via pulse-based electronphoton-solution interface process. Gold atoms of certain transition state develop monolayer assembly at solution surface around the light glow (known in argon plasma) being generated at bottom of copper capillary (known in cathode). The rate of uplifting gold atoms to solution surface is being controlled by forcing energy (travelling photons) pursuing electrons and high energy photons (in high density) entering to solution. Gold atoms dissociated from the precursor under dissipating heat energy into the solution supplied under propagating photons characteristic current through immersed graphite rod (known in anode). Placing packets of nano shape energy of tuned pulse protocol over compact monolayer assembly comprising transition state atoms develop tiny-sized particles of formed shape. On separation of joint tiny particles into two equilateral triangular-shaped tiny particles, exerting forces of surface format elongate atoms of one-dimensional arrays converting them into structures of smooth elements. Due to immersing level of force, such tiny-shaped particles pack from different zones at centre of light glow where they assembled structures of smooth elements for developing mono-layers of different shapes of particles. Developing one-dimensional particles deal assembling of structures of smooth elements of packing tiny-shaped particles from nearly rearward zones of reflection of north-south poles, whereas, developing multi-dimensional particles deal assembling of structures of smooth elements of packing tiny-shaped particles from the east-west poles and near regions. Depending on the number of assembled structures of smooth elements at point of nucleation, packing of tiny-shaped particles from different zones develop different shapes of the anisotropic particles. At fixed precursor concentration, increasing the process time results into develop particles of low aspect ratio. Under tuned parameters, developing mechanisms of particles exhibiting unprecedented features are discussed.

Hybrid reinforcement in a composite material (CM), in many situations, allows better govern material mechanical properties. Polymer matrix CM plate is reinforced with small particles and macro-fibers. Particles are oil shale ash (OSA) powder, macro-fibers – basalt fiber threads im-pregnated by matrix material. With the goal to find out elastic properties of the matrix- polymer with OSA, samples with its different concentrations were experimentally fabricated and their elastic properties were experimentally measured. Obtained data were used in numerical model-ling. Was observed polymer matrix composite slab, reinforced with OSA and three-dimensional (3D) basalt fiber fabric. Fabric are forming threads impregnated by matrix (polymer resin mixed with OSA particles). Damage accumulation in the stretched slab was modelled. Impregnated thread, in the modelling, is observed as a macro-fiber (MF) with averaged elastic properties. With the load increase MF in the material began to break. At first, appeared isolated single breaks. A probabilistic sequential MF rupture accumulation model was accepted and numerical-ly realized. The geometry of the reinforcing knitted fabric was modeled using the Leaf and Glaskin approach. In the knitted fabric highly, stressed MF cross-sections are observed as po-tential location where thread breakage can occur. If one thread breaks, the cross-sections of the adjacent threads experience the overload caused by this rupture. More overloaded crossection in the adjacent overloaded thread breaks and we obtain two adjacent broken MF designated as a defect with the size j=2. The probabilities of obtaining defect consisting of at least 2, 3, … j adjacent broken MF in the plate were calculated. The calculations continued until the rupture process becomes unstable (j→∞). The overstresses on adjacent threads in the CM were calculat-ed using the FEM three-dimensional numerical approach. Analytical and stochastic methods were used for the load-carrying capacity determination and different size defects accumulation in the hybrid composite material (HCM) plate. Also, was calculated the probability of the plate rupture.

Aluminum wire is a common material for wire bonding due to its resistance to oxidation and low price. It does not melt when becoming a free air ball (FAB) during the electronic flame-off (EFO) process with wettability, and is applied by wedge bonding. This study used 20μm Zn-Coated Al-0.5wt.%Si (ZAS) wires to improve the FAB shape after the EFO process, while maintaining stability of the mechanical properties, including the interface bonding strength and hardness. In order to test circuit stability after ball bonding, the current-tensile test was performed. During the experiment, it was found that 80nm ZAS with wire bonding has lower resistance and higher fusing current. For the bias tensile test, the thicker Zn film diffused into the Al-Si matrix easily, after which the strength was reduced. The ball-bond interfaces had no change in their condition before and after the bias. Accordingly, ZAS could be a promising candidate for ball bonding in the future.

The poly lactic acid (PLA) is one of the most used bio-derived thermoplastic polymers in 3D and 4D printing applications. The determination of PLA surface properties is of capital importance in 3D/4D printing technology. (1) Background: The surface thermodynamic properties of PLA polymer were determined by using the inverse gas chromatography (IGC) technique at infinite dilution. The determination of the retention volume of polar and non-polar molecules adsorbed on the PLA particles filling the column allowed us to obtain the dispersive, polar, and Lewis’s acid-base surface properties at different temperatures from 40 °C to 100 °C. (2) Methods: the applied surface method was based on our recent model that used the London dispersion equation and the new chromatographic parameter function of the deformation polarizability and the harmonic mean of the ionization energies of the PLA polymer and organic molecules. (3) Results: The application of this new method led to the determination of the dispersive and polar free surface energy of adsorption of molecules on the polymeric material, as well as the glass transition and the Lewis acid-base constants. (4) Conclusions: four interval temperatures were distinguished showing four zones of the variations of the surface properties of PLA as a function of the temperature before and after the glass transition.

There have been multiple technological advancements that promise to gradually enable devices to measure and record signals with high resolution and accuracy in the domain of Brain Computer Interfaces (BCI). This review paper provides a comprehensive overview of fNIRS, EEG, and fMRI, including their principles, advantages, limitations, and integration with other modalities for advanced BCIs. The paper highlights the advantages of integrating multiple modalities, such as increased accuracy and reliability, and discusses the challenges and limitations of multimodal integration. Applications of advanced BCIs in clinical, assistive, gaming, and entertainment domains are also discussed. Furthermore, we explain the data acquisition approaches for each of these modalities. We also demonstrate various software programs that help in extracting, cleaning, and refining the data. We conclude this paper with discussion on the available literature on data acquisition approaches and a comparison of the ease of use for each of the modalities.

Novel advanced biomaterials have recently gained great attention, especially in surgical minimally invasive techniques. Applying sophisticated design and engineering methods, various elastomer-hydrogel systems (EHS) with outstanding performance have been developed in last decades. Those systems composed of elastomers and hydrogels are very attractive due to their high biocompatibility, injectability, controlled porosity and often antimicrobial properties. Moreover, elastomeric properties and bioadhesiveness are making them suitable for soft tissue engineering. Herein, we present the advances in current state-of-the-art design principles and strategies for strong interface formation inspired by nature (bio-inspiration), diverse properties and applications of elastomer-hydrogel systems in different medical fields, in particular, in tissue engineering. Functionalities of those systems, including adhesive properties, injectability, antimicrobial properties and degradability applicable to tissue engineering will be discussed in a context of future efforts towards development of advanced biomaterials.

The paper presents a method for determining the mutual impedance of two dipoles located on a multilayer dielectric structure. Determining the mutual impedance of linear antennas is a complex issue and we are unable to obtain an exact solution, it is influenced by many elements (location, dimensions, electrical parameters of the earth, thickness of the substrate, thickness and antenna conductivity, etc.) In the case of antennas on a dielectric substrate, the coupling analysis is even more complicated, because the operation of these antennas is significantly influenced by the occurrence of surface waves conducted through an open dielectric structure. The problem was solved by the method of moments using the Galerkin method as its special case. The work uses a method developed by Richmond for obtaining the elements of the impedance matrix, based on the concept of reaction between sections of the base and testing functions. Their mutual interaction was described by the reaction of the electric field caused by the current flowing through one dipole with the current flowing through the other dipole. Based on this analysis, the mutual impedance of two arbitrarily oriented dipoles located on a multilayer dielectric was determined, where the current distribution and antenna lengths are arbitrary. A computer program was developed that allowed to determine the mutual impedance for freely oriented dipoles.

The wide application of graphene in the industry requires the direct growth of graphene films on silicon substrates. In this study, we find a possible technique to meet the requirement above. Multilayer graphene thin films (MLG) are grown without a catalyst on Si/SiO2 by pulsed laser deposition (PLD). It was found that the minimum number of laser pulses that are required to produce fully covered (uninterrupted) samples is 500. This number of laser pulses resulted in samples that contain ~5 layers of graphene. The number of layers was not affected by the laser fluence and the sample cooling rate after the deposition. However, the increase of the laser flu-ence from 0.9 J/cm2 to 1.5 J/cm2, results in 2.5 fold reduction of the MLG resistance. The present study reveals that the PLD method is suitable to produce nanocrystalline multilayer graphene with electrical conductivity of the same magnitude as commercial CVD graphene samples.

A fluid flowing over an object has a tendency to drag the object along it^’s flow direction. An object passing through a fluid which is stationary there is a tendency to slow the object down. For a stationary object in a fluid which is flowing there is a tendency to move the object in the fluid flowing direction .These tendencies of flowing fluid is known as drag. While moving through air airplanes also subjected to several drags. Airplanes subjected to pressure drag or form drag due to flow separation which is based on the pressure difference between the upstream and downstream surfaces of the object. Airplanes also subjected to Skin friction drag which results from the viscous shear of the fluid flowing over the object surface. In order to overcome these drags airplane wings cross section airfoils are designed very carefully. National Advisory Committee for Aeronautics, or NACA, developed and tested "families" of airfoils. Some of the most successful of these were the NACA four-digit and five-digit series. The necessary coordinates for designing NACA airfoil profiles are available in online. UIUC also provide coordinates for designing NACA airfoil profiles. But the present work describes the way of designing NACA four digit airfoils without taking any coordinates from available sources like google or any other search engines. Using C programming with the help of NACA provided equations a generalized source code is designed .Which will provide coordinates for designing any NACA four digit airfoil profiles .With the help of this obtained profile the wing model is also constructed using solid works. Using solid works model the real model was constructed using wood. The chord of regular surface airfoil is 21 cm and the span is also 21 cm. The airfoil profile taken for the model construction is NACA-4415 which is a four digit cambered airfoil.The present work also show some figures of an airfoil by applying certain surface modifications in form of dimples.

Object-level Simultaneous Localization and Mapping (SLAM) has gained popularity in recent years since it can provide a means for intelligent robot-to-environment interactions. However, most of these methods assume that the distribution of the errors is gaussian. This assumption is not valid under many circumstances. Further, these methods use a delayed initialization of the objects in the map. During this delayed period, the solution relies on the motion model provided by an Inertial Measurement Unit (IMU). Unfortunately, the errors tend to accumulate quickly due to the dead-reckoning nature of these motion models. Finally, the current solutions depend on a set of salient features on the object’s surface and not the object’s shape. This research proposes an accurate object-level solution to the SLAM problem with a 4.1 to 13.1 cm error in the position (0.005 to 0.021 of the total path). The developed solution is based on Rao-blackwellized Particle Filtering (RBPF) that does not assume any predefined error distribution for the parameters. Further, the solution relies on the shape and thus can be used for objects that lack texture on their surface. Finally, the developed tightly coupled IMU/camera solution is based on an undelayed initialization of the objects in the map.

This Letter revisits the instability of jet produced by shaped charge. Scaling laws for shaped charge jet are derived by dimensional analysis. It shows that the scaling laws are universal when cross-sectional shrinkage rate is not included in the formulation.

We analyzed the interaction of two acceptor materials, reduced graphene oxide (RGO) and [6,6]-phenyl-C6-butyric acid methyl ester (PCBM), and poly(3-hexylthiphene) (P3HT), as well as the dependence of its photophysical properties with the temperature in the range 90 to 300 K. The nanocomposite of the films was analyzed by optical absorption ultraviolet-visible (UV-Vis) and photoluminescence (PL) and emission ellipsometry (EE) in a function of sample temperature. The surface morphology was studied by atomic force microscopy (AFM). We noted that onset levels (Eonset) of the nanocomposite of P3HT and RGO is smaller than the others. The PL spectra showed the presence of anomalies in the emission intensities in the nanocomposite of P3HT and PCBM. It was also possible to determine the electron-phonon coupling by calculating the Huang-Hys parameters and its dependence with the sample’s temperature. Through EE it was possible to analyze the degree of polarization and the anisotropy. We observed a high degree of polarized emission of the P3HT films which varies subtly according to the temperature. For nanocomposites with RGO the polarization degree in the emission decreases and the roughness on the surface increases. As a result, the RGO improves the energy transfer between adjacent polymer chains at the cost of greater surface roughness. Then, the greater energy transfer may favor applications of this type nanocomposite in OPVC's with enhancement in energy conversion efficiency.

The etiology of Autism Spectrum Disorder (ASD) has been linked to both genetic and epigenetic factors. Among the epigenetic factors, exposure to valproic acid (VPA), an antiepileptic and mood-modulating drug, has been shown to induce characteristic traits of ASD when exposed during embryogenesis. Conversely, in animal models, Enriched Environment (EE) has demonstrated positive behavioral and neural effects, suggesting its potential as a complementary treatment to pharmacological approaches in central nervous system disorders. In this study, we utilized zebrafish to model ASD characteristics induced by VPA and hypothesized that sensory stimulation through EE could ameliorate the behavioral and neuroanatomical features associated with ASD. To test this hypothesis, we assessed social behavior, cerebellar volume, and Purkinje cell populations via histology and immunohistochemistry after exposing the fish to EE. The results revealed that zebrafish exposed to VPA exhibited social deficits, reduced cerebellar cortex volume, and a decrease in c-Fos-positive cells in the Purkinje layer. In contrast, VPA-exposed fish treated with EE showed increased socialization, augmented cerebellar cortex volume, and an elevation in c-Fos-positive Purkinje cells. These findings suggest that alterations induced by VPA may be ameliorated through EE treatment, highlighting the potential therapeutic impact of sensory stimulation in conditions related to ASD.

Environmental concerns, among other causes, are leading to meat replacement in the diet by healthy, nutritious and tasty foods. Alternative protein sources of plant origin can be an alternative to meat, but their low biological value proteins can be a problem. Novel foods, such as insect meals, can meet currently consumer demands. Therefore, this research has developed innovative prototypes of analogue burgers with animal and vegetable proteins. Concerned about health and allergies, a prototype incorporating soya to satisfy coeliacs was developed. An iterative and heuristic process was carried out to test the product development feasibility. The main raw materials used were insect flour (Tenebrio molitor), seitan and soya. In addition, oat and sodium alginate were used as binders. Shelf-life of the new product was evaluated by physicochemical (pH, aw, moisture, colour, acidity and peroxide index) and sensory analysis (quantitative analysis -QDA-). The production of the burger analogues was feasible. Product characterisation showed significant differences (p < 0.05) among samples for organoleptic properties, highlighting texture changes. Using a multivariate model, it was established “The best before date” at 7 days for all developed prototypes, conditioned by microbial growth. Finally, the spoilage model indicated an important contribution to bacterial growth with a notable modification in the pastiness and hardness of the burger analogues developed.

Bioactive surface coatings have retained the attention of researchers and physicians due to their versatility and range of applications in orthopedics, particularly in infection prevention. Antibacterial metal nanoparticles (mNPs) are a promising therapeutic, with vast application opportunities on orthopedic implants. The current research aimed to construct a polyelectrolyte multilayer on a highly porous titanium implant using alternating thin film coatings of chitosan and alginate via the layer-by-layer (LbL) self-assembly technique, along with the incorporation of silver nanoparticles (AgNPs) or titanium dioxide nanoparticles (TiO2NPs), for antibacterial and osteoconductive activity. These mNPs were characterized for their physicochemical properties using quartz crystal microgravimetry with dissipation system, nanoparticle tracking analysis, scanning electron microscopy, and atomic force microscopy. Their cytotoxicity and osteogenic differentiation capabilities were assessed by AlamarBlue and alkaline phosphatase (ALP) activity assays, respectively. The antibiofilm efficacy of the mNPs tested against Staphylococcus aureus. The LbL polyelectrolyte coating was successfully applied to the porous titanium substrate. A dose-dependent relationship between nanoparticle concentration and ALP as well as antibacterial effects was observed. TiO2NP samples were also less cytotoxic than AgNP counterparts, although similarly antimicrobial. Together, these data serve as a proof-of-concept for a novel coating approach for orthopedic implants with antimicrobial and osteoconductive properties.

A multispectral superconducting nanowire single photon detector sensitive to different incident photon wavelength bands, is proposed. The SNSPD consists of a Distributed Bragg Reflector, a gold mirror, and two regions employing four NbN nanowires. Using the DBR both as a filter and a reflector, two distinct detection bands are created. The first detection band has a peak absorbance of > 0.75 at a wavelength of 1143 nm, while the second band has an absorbance of > 0.70 in the wavelength range 1440 to 2000 nm. The design of the device can be tuned to provide sensitivity in different wavelength bands. While SNSPDs do not typically provide photon wavelength sensitivity, the band-selection design proposed in this work opens up potential applications for future quantum communication technology.

Advancing models for accurate estimation of food production is essential for policymaking and managing national plans of action for food security. This research proposes two machine learning models for the prediction of food production. The adaptive network-based fuzzy inference system (ANFIS) and multilayer perceptron (MLP) methods are used to advance the prediction models. In the present study, two variables of livestock production and agricultural production were considered as the source of food production. Three variables were used to evaluate livestock production, namely livestock yield, live animals, and animal slaughtered, and two variables were used to assess agricultural production, namely agricultural production yields and losses. Iran was selected as the case study of the current study. Therefore, time-series data related to livestock and agricultural productions in Iran from 1961 to 2017 have been collected from the FAOSTAT database. First, 70% of this data was used to train ANFIS and MLP, and the remaining 30% of the data was used to test the models. The results disclosed that the ANFIS model with Generalized bell-shaped (Gbell) built-in membership functions has the lowest error level in predicting food production. The findings of this study provide a suitable tool for policymakers who can use this model and predict the future of food production to provide a proper plan for the future of food security and food supply for the next generations.

The work contains a detailed analysis of the electromagnetic field originating from a point source placed above the layered structure.The surface impedance of the multilayer dielectric structure was determined. Based on the boundary conditions, a method for determining the surface impedance of a layered structure with a perfectly conductive screen and or a magnetic screen is presented. The resonance conditions and the conditions for the excitation of surface waves are derived. The integral expression defining the generalized impedance was analyzed with a view to adapting it to numerical implementation. This allowed the development of a computer program based on which calculations were made of the effect of excitation of waves on multilayer dielectric substrates.

Three-layer structures based on various multi-component films of III–V semiconductors heavily doped with Fe were grown by pulsed laser sputtering of InSb, GaSb, InAs, GaAs and Fe solid targets. The structures comprising InAsSb:Fe, InGaSb:Fe and InSb:Fe layers with Fe concentrations up to 24 at. % separated by GaAs spacers were deposited on (001) i-GaAs substrates at 200ºC. Transmission electron microscopy showed that the structures have a rather high crystalline quality and do not contain secondary-phase inclusions. X-ray photoelectron spectroscopy investigations revealed significant diffusion of Ga atoms from the GaAs regions into the InAsSb:Fe layers, which has led to the formation of an InGaAsSb:Fe compound with a Ga content up to 20 at. %. It has been found that the ferromagnetic properties of the InAsSb:Fe magnetic semiconductor improve with increasing Sb:As ratio. It has been concluded that the indirect ferromagnetic exchange interaction between Fe atoms occurs predominantly via Sb atoms.

New analytical solutions of the heat conduction equation are presented in cylindrical and spherical coordinates. Then these solutions are reproduced with high accuracy by recent explicit and unconditionally stable finite difference methods. After this, real experimental data from the literature regarding a heated cylinder are reproduced by the explicit numerical methods as well as by Finite Element Methods (FEM) ANSYS workbench. Convection and nonlinear radiation are also considered on the boundary of the cylinder, and it is shown that the explicit methods are much more accurate than the commercial software.

Triangular resonators re-shaped with the Sierpinski geometry and U-shaped resonators have been designed, linking them with single-pole-double-through (SPDT) RF MEMS switches to provide frequency tuning for potential applications in the K-Band. Prototypes of band-stop narrowband filters working around 20 GHz and 26 GHz, interesting for RADAR and satellite communications, have been studied in coplanar waveguide (CPW) configuration, and the tuning was obtained by switching between two paths of the devices loaded with different resonators. As a result, dual-band operation or fine-tuning can be obtained depending on the choice of the resonator, acting as a building block. The studied filters belong to the more general group of devices inspired by the metamaterial design.

A triangular lattice model for pattern formation by core-shell particles at fluid interfaces is introduced and studied for the particle to core diameter ratio equal to 3. Repulsion for overlapping shells and attraction at larger distances due to capillary forces are assumed. Ground states and thermodynamic properties are determined analytically and by Monte Carlo simulations for soft outer- and stiffer inner shells, with different decay rates of the interparticle repulsion. We find that thermodynamic properties are qualitatively the same for slow and for fast decay of the repulsive potential, but the ordered phases are stable for temperature range depending strongly on the shape of the repulsive potential. More importantly, there are two types of patterns formed for fixed chemical potential - one for a slow and another one for a fast decay of the repulsion at small distances. In the first case two different patterns - for example clusters or stripes - occur with the same probability for some range of the chemical potential. For fixed concentration, an interface is formed between two ordered phases with the closest concentration, and the surface tension takes the same value for all stable interfaces. In the case of degeneracy, a stable interface cannot be formed for one out of four combinations of the coexisting phases, because of a larger surface tension. Our results show that by tuning the architecture of a thick polymeric shell, many different patterns can be obtained for sufficiently low temperature.

Spin valves with a synthetic antiferromagnet were fabricated by magnetron sputtering. It was shown that the fabricated spin valves had perfect microstructure of layers and smooth interfaces, therefore RKKY interaction dominates in coupling of ferromagnetic layers separated by a copper spacer. Rhombus-shaped microobjects were fabricated from a single spin valve film. The thermomagnetic treatment procedure was found, to form unidirectional anisotropy in the microobject so, that the values of the exchange bias fields in the rhombus’ nonparallel sides were opposite in sign. For the synthetic antiferromagnet CoFeNi/Ru/CoFeNi the difference between ferromagnetic layers thicknesses was found, at which the thermomagnetic treatment forms the same exchange bias all over the rhombus’ side. The sensor element was fabricated in which each side of the rhombus was a shoulder of a Wheatstone bridge. After the thermomagnetic treatment procedure each shoulder worked as an active magnetosensitive element, thus the device operated as the full Wheatstone bridge. The sensor output has the shape of a step, high sensitivity to field change and significant magnetic hysteresis. Such characteristics are suitable for switching devices.

Accurate classification of objects in 3D point clouds is a significant problem in several applications, such as autonomous navigation and augmented/virtual reality scenarios, which has become a research hot spot. In this paper, we presented a deep learning strategy for 3D object classification in augmented reality. The proposed approach is a combination of the GRU and LSTM. LSTM networks learn longer dependencies well, but due to the number of gates, it takes longer to train; on the other hand, GRU networks have a weaker performance than LSTM, but their training speed is much higher than GRU, which is The speed is due to its fewer gates. The proposed approach used the combination of speed and accuracy of these two networks. The proposed approach achieved an accuracy of 0.99 in the 4,499,0641 points dataset, which includes eight classes (unlabeled, man-made terrain, natural terrain, high vegetation, low vegetation, buildings, hardscape, scanning artifacts, cars). Meanwhile, the traditional machine learning approaches could achieve a maximum accuracy of 0.9489 in the best case.

Solute decoration at grain boundaries (GB) leads to a number of phenomenon such as changes in interface structure, mobility, cohesion etc. Recent experimental investigations on interfacial segregation in steels are based on microstructural characterisation using two correlative methodologies, namely, Transmission Electron Microscopy-Atom Probe Tomography (APT) and Electron Backscatter Diffraction-APT. Considering the growing interest in this avenue, the present review is aimed at addressing the common adsorption isotherms used for quantifying interfacial segregation and providing an overview of the present state of experimental research in the area of GB segregation in steels. The areas where an understanding of GB segregation may be utilised have also been highlighted with a focus on the experimental challenges associated with understanding GB segregation in steels.

Omega-3 polyunsaturated fatty acids (ɷ-3 PUFAs) offer diverse health benefits, such as supporting cardiovascular health, improving cognitive function, promoting joint and musculoskeletal health, and contributing to healthy aging. Despite their advantages, challenges like oxidation susceptibility, low bioavailability, and potential adverse effects at high doses persist. Nanoparticle encapsulation emerges as a promising avenue to address these limitations while preserving stability, enhanced bioavailability, and controlled release. This comprehensive review explores the therapeutic roles of omega-3 fatty acids, critically appraising their shortcomings and delving into modern encapsulation strategies. Furthermore, it explores the potential advantages of Metal-organic framework nanoparticles (MOF NPs) compared to other commonly utilized nanoparticles in improving the therapeutic effectiveness of omega-3 fatty acids within drug delivery systems (DDS). Additionally, it outlines future research directions to fully exploit the therapeutic benefits of these encapsulated omega-3 formulations for cardiovascular disease treatment.

Understanding the dynamics of Organic Carbon mineralization is fundamental in forecasting biosphere to atmosphere Net Carbon Ecosystem Exchange (NEE). With this perspective, we developed 3D-CMCC-PSM, a new version of the hybrid Process Based Model 3D‐CMCC FEM where also heterotrophic respiration (R_h) is explicitly simulated. The aim was to quantify NEE as a forward problem, by subtracting Ecosystem Respiration (R_eco) to Gross Primary Productivity (GPP). To do so, we developed a simplification of the Soil Carbon dynamics routine proposed in DNDC [1]. The method calculates decomposition as a function of soil moisture, temperature, state of the organic compartments, and relative abundance of microbial pools. Given the pulse dynamics of soil respiration, we introduced modifications in some of the principal constitutive relations involved in phenology and littering sub-routines. We quantified the model structure related uncertainty in NEE, by running our training simulations over 1000 random parameter-sets extracted from parameters distributions expected from literature. 3D-CMCC-PSM predictability was tested on independent time series for 6 Fluxnet sites. The model resulted in daily and monthly estimations highly consistent with the observed time series. It showed lower predictability in Mediterranean ecosystems, suggesting that it may need further improvements in addressing evapotranspiration and water dynamics.

Urbanization and climate change have increased the need for stormwater management and nature-based solutions. Decisions made at project level impact the emergence of systemic traits of the stormwater network and the functionality of the catchment areas in urban planning. To that end, it is vital to introduce the decision-making tools for analyzing both the utilities and amenities of nature-based solutions (NBS) to increase their adoption to reduce the peak loads in the stormwater system, and to that end, mitigate the impacts of climate change. This paper demonstrates a workflow using drone-based photogrammetry, 3D modeling, and simulation software to generate visual and functional models assisting in informed decision-making in the design of stormwater systems as functional landscape architecture. Using aerial data from drones and modeled design solutions, the proposed workflow simulates rain events, infiltration, evaporation, water flow, and accumulation of stormwater in a way that allows the visual and quantified analysis of detailed landscape architecture designs. The paper provides an example of a rooftop site simulation demonstrating the infiltration and flow of water to the drainage. The visual decision-making method provided can aid in investment decisions for functional landscape design in support of stormwater management.

Tinnitus is a heterogeneous auditory disorder without a pharmacological cure but with several palliative treatments. One of the most applied treatments for tinnitus relief combines counselling with sound therapy. The efficiency of this sound therapy depends on the type of sound stimulus and the exposition time. The fundamentals of a customized sound therapy that stimulates the auditory system with a continuous or sequential sound which compensates for the subject hearing loss are described here. A sample of 137 tinnitus subjects are treated with this sound therapy, named Enriched Acoustic Environment. 90% of these patients achieved a clinically relevant and statistically significant tinnitus-related distress relief quantified as a mean drop of their Tinnitus Handicap Inventory score of 24.3 points. These subjects exposed with sequential stimuli (31%) achieved greater distress relief (5.1 points more in their Tinnitus Handicap Inventory score) than those stimulated with continuous sound (69%). Therefore, this sound constitutes an optimized stimulus for tinnitus treatment.

Rotorcrafts operate HUMS for fault diagnosis, but the capabilities of HUMS analysts are important due to the complex mechanical configuration of rotorcraft and the difficulty of analysis. Accordingly, an advanced algorithm is needed to identify faults, and flight data can be used to develop the algorithm. However, flight data contains abnormal or missing data due to problems such as sensor defects, which can be a major problem in algorithm development. Therefore, in this paper, we study a gap filling method using MLP to obtain normal data when there are problems such as abnormal or missing data in rotorcraft flight data. Existing methods typically fill the gap through interpolation or curve fitting using the before and after values of missing data. However, in this study, normal values were estimated using the values of other parameters at the moment of missing or abnormal data occurred. As a result of evaluating the performance of the trained MLP using normal data, it was confirmed that the output of the model well estimates the changing trend of the target. And when abnormal data was applied to the trained model, it was confirmed that point outliers were eliminated and appropriate values were found in the case of missing data.