Day by day, the share of renewable energy-based power plants such as offshore wind farms and photovoltaic power plants, in the present-day power systems is escalating. Nevertheless, most of these power-producing facilities have been located quite far away from the load centers. At this stage, HVDC power systems provide satisfactory options due to qualities such as reduced line losses, substantial controllability, and environmental advantages. Nevertheless, unique converter designs are required to combine asynchronous HVDC networks with each other and with already existing high voltage alternating current (HVAC) networks. In this study, based on the above special cases, a unique DC-DC modular multilevel converter (MMC) architecture is presented that provides an excellent solution for both integrating modern asynchronous HVDC networks and integrating these modern HVDC power systems with existing asynchronous HVAC power systems. The mathematical analysis of the recommended DC-DC MMC design has been examined in detail and the power transfer between two asynchronous power grids has been realized in a simulation environment. Efficient bilateral power transmission has been made achievable by the control system. The recommended DC-DC MMC topology has shown to be a highly successful approach, in the interconnection of HVDC power systems, according to the simulation results.

In modern inverter applications, multilevel converters are used thanks to their capability of reducing the passive fi lter volumes, improving the overall THD, sharing the power sources across the several converter cells, and providing a reconfi guration ability in case of failure. However, increasing the number of cells makes more complex the control of the converter. This article proposes a decentralized control technique based on the use of elementary modular controllers, associated with each converter cell and communicating with their close neighbors to obtain the balancing of the powers they supplied. Each modular controller can be dynamically removed or added to allow reconfi guration of the converter for functional safety purpose. This method is applied to a 240V/3A 5-cells Cascaded Full-Bridge Multilevel Converter. The response of the system to load transients and cell voltage disturbances demonstrates the robustness of the proposed decentralized control method. Thanks to the use of modular controllers, the number of levels of the converter can be extended to the order N without adding complexity to its control.

This paper presents the design and implementation of a digital control system for modular multilevel converters (MMC) and its use in a 5-kW small scale prototype. To achieve higher system control reliability and multi-functionality, the proposed architecture has been built with an effective split of the control tasks between a master controller and six slave controllers, one for each of the six arms of the converter. The MMC prototype have been used for testing both converter and system level controls in a reduced scale laboratory set up of a Multi-Terminal DC transmission network (MTDC). The whole control has been tested in order to validate the proposed control strategies. The tests performed at system level allowed to explore the advantages of using an MMC in a MTDC system.

Abstract: High step-up voltage gain nonisolated DC-DC converter have attracted much attention in photovoltaic, fuel cells and other renewable energy system applications. In this paper, by combining input current ripple-free boost cell with coupled-inductor voltage-doubler cell, an input current ripple-free high voltage gain nonisolated converter is proposed. In addition, passive lossless clamp circuit is adopted to recycle the leakage inductor energy and to reduce the voltage spike across the power switch. By utilizing voltage-doubler cell consisting of diode and capacitor, the voltage stress of switch is further reduced and the resonance between the leakage inductor and the stray capacitor of the output diode is eliminated. A low switch-on-resistance low-voltage-rated MOSFET can therefore be employed to reduce the conduction loss and cost. The reverse recovery loss of output diode is reduced, and the efficiency of converter can be improved. Furthermore, the proposed converter can achieve nearly zero input current-ripple and make the design of electromagnetic interference (EMI) filter easy. Steady state analysis and operation mode of the converter is performed. Finally, experimental results are presented to verify the analysis results of the proposed converter.

The paper focuses on the application of a multilevel, integrative and territorial approach to the protection of cultural heritage through planning instruments in Serbia. It points out the problems of the sectoral approach and discusses international recommendations that can be integrated into the planning methodology. The case study is the area of Djerdap National Park, which has an already established international and national importance. The research suggests that the cultural heritage in the area, with the exception of the Roman limes, is still recognized at the level of individual localities. The study emphasizes the importance of aligning all levels of governance to safeguard the whole spatial entity rather than focusing solely on its particular areas. The interna-tional and national importance of the planning area contributes to the strengthening of awareness of heritage and its institutional protection. However, the vitality of the area, which is key to its sustainable development, comes from the local level. Planning documents contribute to the inte-gration of local values and local communities into development programs and projects.

The wave energy converter (WEC) technology constantly develops new designs and models. To encourage its development within the energy sector, research is required to improve current designs and create durable and effective devices. However, it is also crucial to investigate the suitability of a WEC to a site-specific sea condition as this can impact its optimal power absorption and constructability. This study evaluates and compares the efficiency of a heaving buoy with varied geometries in one of the most energetic places along the Mexican coast. A statistical analysis of the wave climate on the coast of Ensenada during the last 42 years is performed to define the conditions to which the device is subjected. The location of the WEC in shallow waters is chosen using a computational model which solves the modified mild slope equation in its elliptic shape. The heaving buoy floater is studied using three distinct geometries: a semi-sphere, a cylinder, and a proposed rounded semi-rectangle. The hydrodynamic response of the three geometries is then analysed in the frequency and time domain using ANSYS AQWA. The hydrodynamic study involves the assessment of the floating body dynamics, exerted forces, the power absorbed as well as the suitability of the proposed power take-off (PTO) system. Findings reveal that the proposed geometry absorbs the most energy, with an annual power of 135.11 MW, and that the transmission PTO design is appropriate for this type of technology.

Colorectal cancer is a high-incidence tumor that has a high mortality rate due to its frequent metastasis to the liver. The difference in genes, proteins, and immune microenvironment between the primary and metastatic sites causes them to show different responses to treatment. Colorectal cancer liver metastasis patients also tend to show poorer treatment response and prognosis. Therefore, in this paper, we summarize the heterogeneity exhibited after colorectal cancer liver metastasis from five aspects (gene, transcriptome, protein, metabolism, and immunity), and we found that except for the genetic heterogeneity, the other four aspects exhibite significant heterogeneity, which might serve as a new therapeutic direction and a prognostic marker for patients with liver metastasis. Finally, the therapeutic modalities regarding tumors are rapidly evolving, and we have also summarize the new clinical therapeutic modalities currently proposed based on these heterogeneities, aiming to provide new therapeutic ideas for the clinical treatment of patients with colorectal cancer liver metastases.

This paper presents a novel improvement of MuSIASEM (Multiscale Integrated Analysis of the Societal and Ecological Metabolism) by incorporating a new regional analysis of the electricity metabolism across levels. An analysis of Mexico illustrates this toolkit and shows that the industry sector had Economic Energy Intensity (EEI) with 40.3 MWh/MMXN reached a higher value than the commerce and services sector with 0.84 MWh/MMXN. Regarding the Economic Labor Productivity (ELP) indicator (AV/h), the industrial sector with 208.5 TMXN/Kh reached a higher value than the Commercial and services sector with 114.3 TMXN/Kh. With reference to the Exosomatic Metabolic Rate (EMR), the Household sector obtained 59.3 KWh/Kh whereas the paid sector reached 2,486.4 KWh/Kh. Disaggregation of the EMR indicator into economic sectors shows that the Industrial sector obtained 8.4 KWh/Kh and the commercial and services sector reached 0.10 KWh/Kh. The lack of complete data for the agricultural sector does not allow us to calculate EEI, ELP, and EMR indicators accurately. Considering the analysis of indicators by regions, regarding the EEI rate, the Central region had the lowest value with 12.7 MWh/MMXN, followed by the Northeast with 21.4 MWh/MMXN and Western with 29.4 MWh/ MMXN, which means that they require less electricity to produce more added value. In terms of the ELP indicator, it was found regions with higher values were Northeast with 182.3 MMXN/Mh, Central with 177.5 MMXN/Mh, and North with 127 MMXN/Mh, which means that these regions produce more added value per hour of work. About the EMR, it is observed that regions in the northern part of the country had higher values: Northwest with 337 KWh/Kh, Baja California Sur with 334 KWh/Kh, Baja California with 328 KWh/Kh, North with 313 KWh/Kh and Northeast with 274 KWh/Kh, which means that these regions consume more electricity per hour. This innovative approach is useful for governance because it helps to understand and reduce asymmetries across regions, resulting in more social equality and a better economic equilibrium across sectors and regions.

The past two decades has seen a growing demand for high-power, high-voltage utility scale inverters mostly fueled by the integration of large solar PV and wind farms. Multilevel inverters have emerged as the industry choice for these megawatt range inverters because their reduced voltage stress, capable of generating an almost sinusoidal voltage, in-built redundancy, among others. This paper present a new Switched-Source Multilevel Inverter (SS MLI) architecture. The new inverter show superior over existing topologies. It has reduced voltage stress on the semiconductor, uses less number of switches –reduced size/weight/cost and increased efficiency. The new SSMLI is comprised of two voltage sources (V₁, V₂) and 6 switches. It is capable of generating 5-level output voltage in symmetric modes (i.e., V₁ = V₂), and 7-level output voltage in asymmetric modes (i.e., V₁ ≠ V₂). To demonstrate the validity of the proposed inverter, simulations results using MATLAB^® /Simulink^® for 5- and 7-level output voltages are presented . The simulations are also verified experimentally using a laboratory prototype.

This research presents the design and characteristics of new wideband polarizer based on the square waveguide with irises. Matching and polarization characteristics of the polarizer have been simulated and optimized. Frequency dependences of the characteristics are presented. Developed polarizer can be applied in satellite information systems.

The growing attention for plug-in electric vehicles, and the associated high-performance demands, have initiated a development trend towards highly efficient and compact on-board battery chargers. These isolated ac-dc converters are most commonly realized using two conversion stages, combining a non-isolated power factor correction (PFC) rectifier with an isolated dc-dc converter. This, however, involves two loss stages and a relatively high component count, limiting the achievable efficiency and power density and resulting in high costs. In this paper a single-stage converter approach is analyzed to realize a single-phase ac-dc converter, combining all functionalities into one conversion stage and thus enabling a cost-effective efficiency and power density increase. The converter topology consists of a quasi-lossless synchronous rectifier followed by an isolated dual active bridge (DAB) dc-dc converter, putting a small filter capacitor in between. To show the performance potential of this bidirectional, isolated ac-dc converter, a comprehensive design procedure and multi-objective optimization with respect to efficiency and power density is presented, using detailed loss and volume models. The models and procedures are verified by a 3.7 kW hardware demonstrator, interfacing a 400 V dc-bus with the single-phase 230 V, 50 Hz utility grid. Measurement results indicate a state-of-the-art efficiency of 96.1% and power density of 2.2 kW/dm³, confirming the competitiveness of the investigated single-stage DAB ac-dc converter.

Recent studies suggest that PEBP1/RKIP and YY1, despite having distinct molecular functions, may interact and mutually influence one another's activity. They exhibit reciprocal control over each other's expression through regulatory loops, prompting the hypothesis that their interplay could be pivotal in cancer advancement and resistance to drugs. To delve into this interplay's functional characteristics, we conducted a comprehensive analysis using bioinformatics tools across a range of cancers. Our results confirm the association between elevated YY1 mRNA levels and varying survival outcomes in diverse tumors. Furthermore, we observed differing degrees of inhibitory or stimulatory effects of these two genes in various cancer pathways, along with correlations between their mRNA expression and immune infiltration. Additionally, YY1/PEBP1 expression (or methylation) displayed connections with genomic alterations across cancer types. Notably, we uncovered links between YY1/PEBP1 and different indicators of immunosuppression, such as immune checkpoint blockade response, and T-cell dysfunction/exclusion levels, across different patient groups. Overall, our findings underscore the significant role of the interplay between YY1 and PEBP1 in cancer progression, influencing genomic changes, tumor immunity or the tumor microenvironment. Additionally, these two gene products appear to impact the sensitivity of anticancer drugs, opening new avenues for cancer therapy.

Although microgrids facilitate the increased penetration of distributed generations (DGs) and improve the security of power supplies, they have some issues that need to be better understood and addressed before realising the full potential of microgrids. This paper presents a comprehensive list of challenges and opportunities supported by a literature review on the evolution of converter-based microgrids. The discussion in this paper presented with a view to establishing microgrids as distinct from the existing distribution systems. This is accomplished by, firstly, describing the challenges and benefits of using DG units in a distribution network and then those of microgrid ones. Also, the definitions, classifications and characteristics of microgrids are summarised to provide a sound basis for novice researchers to undertake ongoing research on microgrids.

We consider a class of density-driven flow problems. We are particularly interested in the problem of the salinization of coastal aquifers. We consider the Henry saltwater intrusion problem with uncertain porosity, permeability, and recharge parameters as a test case. The reason for the presence of uncertainties is the lack of knowledge, inaccurate measurements, and inability to measure parameters at each spatial or time location. This problem is nonlinear and time-dependent. The solution is the salt mass fraction, which is uncertain and changes in time. Uncertainties in porosity, permeability, recharge, and mass fraction are modeled using random fields. This work investigates the applicability of the well-known multilevel Monte Carlo (MLMC) method for such problems. The MLMC method can reduce the total computational and storage costs. Moreover, the MLMC method runs multiple scenarios on different spatial and time meshes and then estimates the mean value of the mass fraction. The parallelization is performed in both the physical space and stochastic space. To solve every deterministic scenario, we run the parallel multigrid solver ug4 in a black-box fashion. We use the solution obtained from the quasi-Monte Carlo method as a reference solution.

This article proposes the multilayer and multilevel cosmological model, on average, balanced with respect to the Einsteinian vacuum. This hierarchical model is based on 10 possible Kottler solutions of the extended Einstein's field equations. The extension of the Einstein field equations is associated with the addition of an infinite number of lambda_j-terms to these equations with the condition that the series (i.e., the total sum) of these terms converges to zero. A simplified ten-layer and ten-level case is considered, in which ten spherical formations are sequentially nested into each other like "nesting dolls", while the radii of these spherical formations correspond to the characteristic sizes of a discrete sequence of observed spherical objects: metagalaxy core, galactic cores, stellar (planet) core, biological cells and nuclei of atoms and elementary particles, etc. As an example, from the general ten-level (hierarchical) solution of extended Einstein's field equations, two antipodal spherical formations with a core radius commensurate with the classical electron radius are singled out. Therefore, the metric-dynamic models of these formations obtained in this way are called «electron» and «positron». The article is aimed at the development of differential geometry and the program for the complete geometrization of physics by Clifford-Einstein-Wheeler.

This paper proposes a new cascaded three-phase multilevel inverter based on a cascaded submultilevel and single-phase H-bridge structure. The voltage source of the traditional single-phase H-bridge is replaced with the proposed cascaded submultilevel. Cascading two basic units forms the submultilevel unit. The basic and submultilevel units generate positive voltage only hence the need for an H-bridge to generate both polarities of load voltage. Five algorithms of source voltage are proposed and the optimal algorithm selected to generate the peak load voltage and output levels. The proposed three-phase cascaded multilevel inverter generates 31-level of load voltage. The per-phase component distribution of the proffered inverter are twelve power switches, four dc sources and twelve driver circuits accordingly. Principal merits of the proposed 31-level inverter are high quality load waveforms, production of high levels of load voltage utilizing reduced component quantity, simple cascaded layout, decreased inverter area, minimal inverter cost, minimum inverter losses and utilizing lower rated switches. Also, the proposed topology is highly suited for employment in PV-DVR and other power systems. To validate these advantages of the proposed multilevel inverter, contrastive analysis of the proposed inverter and existing topologies are studied. Finally, the functionality of the proposed inverter is substantiated by simulation in PSCAD/ EMTDC software.

The unprecedented growth of publicly available SARS-CoV-2 genome sequence data has increased demand for effective and accessible SARS-CoV-2 data analysis and visualization tools. A majority of the currently available tools either require computational expertise to deploy or limit user input to pre-selected subsets of SARS-CoV-2 genomes. To address these limitations, we developed ViralVar, a publicly available, point-and-click webtool that gives users the freedom to investigate and visualize user-selected subsets of SARS-CoV-2 genomes obtained from the GISAID public database. ViralVar has two primary features that enable: 1) visualization of spatiotemporal dynamics of SARS-CoV-2 lineages, and 2) structural/functional analysis of genomic mutations. As proof-of-principle, ViralVar was used to explore the evolution of the SARS-CoV-2 pandemic in the USA in the pediatric, adult, and elderly population (n > 1.7 million genomes). While the spatiotemporal dynamics of variants did not differ between these age groups, several USA-specific sublineages arose relative to the rest of the world. Our development and utilization of ViralVar to provide insights on the evolution of SARS-CoV-2 in the USA demonstrates the importance of developing accessible tools to facilitate and accelerate large-scale surveillance of circulating pathogens. The ViralVar webserver is freely available at http://viralvar.org/.

Exploring new ways to represent and discover organic molecules is critical for developing novel therapies. With recent advances in bioinformatics, virtual screening of databases is possible. However, biochemical data must be encoded using computer algorithms to make them machine-readable, taking into account distance and similarity measures to support tasks such as similarity searching. Motivated by the ubiquity of the carbon element and the structured patterns that emerge, we propose a parametric approach to molecular encodings of carbon-based multilevel atomic neighborhoods. It implements a walk along the carbon chain of an organic molecule to compute different representations of its feature encoding in the form of a binary or numerical array that can be exported later into an image. Resulting encodings are reproducible and readily formatted for various domain tasks including machine learning tasks. This approach was evaluated using a 10-fold stratified cross validation for binary classification with eight data sets and six different encodings (384 models) in the domain knowledge of cell-penetrating peptides. The parametric approach is built on open-source software and is implemented as a Python package (cmangoes). Source code and documentation are available at https://github.com/ghattab/cmangoes.

Ocean wave energy is a significantly well-liked renewable energy source. The Internet of Things (IoT) offers a great opportunity for development of the ocean wave energy research. The IoT technology significantly enhanced the performance of the ocean wave energy converter (WEC). The data obtained from IoT devices reduce the risk of using WEC. However, Integrating IoT devices with the WEC is a daunting task because controlling the WEC needs real-time data. This paper investigated the performance of WEC and estimate the lifetime of the modules. IoT devices integrated with various sensors determine different parameters and conditions of the ocean. The IoT platform is used for wireless voltmeters, wireless AC current meters, wireless voltage detection, wireless resistance sensors, wireless temperature sensor, wireless accelerometer, wireless pressure meters, and wireless water level sensors to determine the real-time condition of the ocean wave. These devices are also proven to be reliable and accurate.

This research presents a maximum power point tracking of traditional single-ended primary converter (SEPIC) with the aid of fuzzy logic controller (FLC) for regulating the voltage and perturbation and observation(P&O) algorithms for regulating the reference voltage and reaching the maximum power point tracking. This is a promising technique for the conventional SEPIC converter to achieve maximum power point tracking with much less error. Moreover, the method is simple, reliable, and understandable for photovoltaic systems.

The matrix converter converts the input line voltage into a variable voltage with an unrestricted output frequency without using an intermediate circuit, dc link circuit. A pure sine in and pure sine out is the unique feature of the matrix converter. This research paper also analyzes the basic operating principle and the simulation modeling of the direct matrix converter, which is controlled by the Space Vector Pulse Width Modulation technique by using the software which is known as MATLAB/Simulink. The most desirable features in the power frequency changes can be fulfilled by using the matrix converters, and this is the reason for the tremendous interest in the topology. Since the power electronic circuits which is known as the motor drives are used to operate the AC motors at the frequencies other than that of the supply.

In this paper, a method of charging lead acid battery with solar power by flyback converter is proposed. The basic system consists of a buffer circuit, auxiliary power circuit, control circuit, voltage feedback circuit and current feedback circuit. The system is capable of monitoring battery voltage and the current, charging the coupling inductor and automatic control of output duty cycle, overcharging and over-discharging protection. The experiment proves that the charging efficiency is improved by about 83% at full load.

Background: Obstructive sleep apnea (OSA) is caused by partial or complete obstruction of the upper airways. Corrective surgeries aim at removing obstructions in the nasopharynx, oropharynx, and hypopharynx. OSA is associated with increased risk of various metabolic diseases. Our objective was to evaluate the effect of surgery on the plasma metabolome. Methods: This study included 39 OSA patients who underwent Multilevel Sleep Surgery (MLS). Clinical and anthropometric measures were taken at baseline and 5 months after surgery. Results: The mean Apnea Hypopnea Index (AHI) significantly dropped from 22.0 ± 18.5 events/hour to 8.97 ± 9.57 events/hour (p-Value <0.001). The Epworth’s sleepiness Score (ESS) dropped from 12.8 ± 6.23 to 2.95 ± 2.40 (p-Value <0.001) indicating success of the surgery in treating OSA. Plasma levels of metabolites, phosphocholines (PC) PC.41.5, PC.42.3, ceremide (Cer) Cer.44.0, and triglyceride (TG) TG.53.6, TG.55.6 and TG.56.8 were decreased (p-Value<0.05) whereas lysophosphatidylcholines (LPC) 20.0 and PC.39.3 were increased (p-Value<0.05) after surgery. Conclusion: This study highlights the success of MLS in treating OSA. Treatment of OSA resulted in improvement in metabolic status that was characterized by decreased TG, PCs and Cer metabolites post-surgery indicating that the success of the surgery positively impacted the metabolic status of these patients.

This retrospective study aimed to investigate the effect of known risk factors on nonsurgical periodontal treatment (NSPT) response using a pocket depth fine-tuning multilevel linear model (MLM). Thirty-seven patients (24 males and 13 females) with moderate to severe chronic periodontitis were treated with nonsurgical periodontal therapy. Follow-up visits at 3, 6, and 12 months included measurement of several clinical periodontal parameters. Data were extracted from a database system. Probing depth (PD) and Clinical Attachment Loss (CAL) reductions after NSPT in an overall of 1416 initially affected sites (baseline PD ≥ 4 mm), distributed on 536 teeth, were analyzed against known risk factors at three hierarchical levels (patient, tooth and site). The variance component models fitted to assess the three-level variance of PD and CAL decrease for each post-treatment follow-up showed that all levels contributed significantly to the overall variance (P < 0.001). Patients that underwent NSPT and were continually monitored had very curative results. All three hierarchical levels included risk factors who had impact on the to influence the magnitude of PD and CAL reduction. Specifically, the tooth’s type, surfaces involved and teeth mobility site-level risk factors showed the highest influence on these reductions, being highly relevant factors for the NSPT success.

Ice covering on overhead transmission lines would cause damage to transmission system and long-term power outage. Among various de-icing devices, modular multilevel converter (MMC) based DC de-icer (MMC-DDI) is recognized as a promising solution due to its excellent technical performance. Its principle feasibility has been well studied, but few literature discuss its economy or hardware optimization, thus the designed MMC-DDI for high voltage transmission lines is usually too large and too expensive for engineering applications. To fill this gap, this paper presents a quantitative analysis on the converter characteristics of MMC-DDI, and calculates the minimal converter rating and its influencing factors. It reals that, for a given de-icing requirement, the converter rating varies greatly with its AC-side voltage. Then an optimization configuration is proposed to reduce the converter rating and improve its economy. The proposed configuration is verified in a MMC-DDI for a 500kV transmission line as a case study. The result shows, in the case of outputting same de-icing characteristics, the optimized converter rating is reduced from 151 MVA to 68 MVA, and total cost of MMC-DDI is reduced by 48%. This analysis and conclusion are conductive to the optimized design of multilevel DC de-icer, then to its engineering application.

This paper presents a comprehensive study and the analysis of a topology of a no isolated DC-DC intituled Double Quadratic Boost converter with high static gain. This converter has the main advantage of high static gain and low voltage stress on its switches. The article will first present the theoretical analysis of the converter operating in an open loop. The objective of the work is the mathematical modeling and the control strategy of the converter, as well as the validation through closed-loop experimental results. Besides, we presented the practice test results to demonstrate the operation of the converter, such as the static gain experimental curve, the practice efficiency of the converter, and the control of the output voltage, as well as the capacitor voltage balance control. The authors designed a prototype for 1 kW, with a switching frequency of fs=50kHz, with FPGA-based command and modulation.

A Shape Memory Alloy (SMA) enabled Overtopping Wave Energy Converter (OWEC) that maximizes its overtopping discharge, and thus energy output under different wave conditions is presented. Among all the parameters affecting the overtopping discharge rate, the crest freeboard height is the most influential one to control the overtopping discharge rate and the stored overtopping volume behind it. Currently, all the OWEC crest freeboard heights are fixed by design to maximize the discharge rate on one particular sea state. In the present study, we show that the SMA can adjust the crest freeboard height through a control system based on the sea state and achieve an optimal overtopping discharge rate. A scaled OWEC model is built in the lab with its crest freeboard height controlled by springs made of SMA. The length (and thus tension) of the springs is controlled by temperature changes by changing the passing current through the springs. By adjusting the length of the springs based on the incoming wave condition, we adjust the freeboard to an optimal height known to generate a maximum overtopping discharge rate for energy conversion. This smart material-enabled design can maximize the overtopping discharge and thus the output power of the OWEC under various wave conditions. Furthermore, the simplicity of using SMA springs as the actuator leads to the minimum number of moving mechanical parts, which can remarkably decrease maintenance costs. As the proof of concept, two types of tests are conducted in the laboratory using the same OWEC model under several random wave trains generated from spectra with different significant wave heights - one type with a fixed crest freeboard height and the other type featuring the adjustable crest freeboard height controlled by the springs. The substantial increase of harvested output power in the OWEC with the adjustable crest freeboard height may pave the way for more efficient wave energy conversion systems.

In this research paper, a high gain transformer less inverter modeling which is used for the smart grid technology or as the stand alone for home appliances is proposed. The proposed transformer less topology provides a higher voltage gain, low cost, small size and simple control stand alone transformer less inverter for home appliances. The above inverter is modeled by using software which is known as MATLAB/ Simulimk.

To improve the voltage gain of step-up converters, cascaded technique is considered as a possible solution in this paper. By considering the concept of cascading two Z-source networks in a conventional boost converter, the converter takes the advantages of both impedance source and cascaded converters. However, by applying some modifications, the proposed converter provides high voltage gain while the voltage stress of switch and diodes are still low. Moreover, the low input current ripple of the converter makes it absolutely appropriate for photovoltaic applications in order to expand the lifetime of PV panels. After analyzing the operation principles of the proposed converter, simulation and experimental results of a 100W prototype are presented to verify the proposed converter performance.

In this research paper, a novel high step up dc-dc converter with a coupled inductor and voltage doubler circuits is proposed. The converter achieves a high step up voltage gain with an appropriate duty ratio and low voltage stress on the power switches. Also, the energy which is stored in the leakage inductor of the coupled inductor can be recycled to the output. The operating principles and the steady state analysis of the proposed converter are discussed in detail. Finally, a prototype circuit of the proposed converter is implemented in the laboratory in order to verify the performance of the proposed converter.

Voltage sags can cause the interruption of power supply and can negatively affect operations of customers. In this paper, the authors study the impact of battery energy storage systems (BESS) on voltage sags. A stochastic method of fault positions is used. Faults of various types are simulated and voltages are recorded. Firstly, with the BESS integrated into the network, there are higher residual voltages, fewer voltage sags and less expected critical voltage loss. Secondly, if the BESS converter power factor is reduced, recorded residual voltages are higher, voltage sags are fewer, and the number of expected critical voltage sags is lower. Finally, when three BESS converter control modes, namely constant voltage, constant power factor, and constant reactive power, were assessed, results showed similar voltage sag performances for constant power factor and constant reactive power modes. Furthermore, operating in constant voltage control outperformed the other two modes as it resulted in higher residual voltages, a lower number of voltage sags, and fewer expected critical voltage sags. The paper has demonstrated that the BESS can improve voltage sag performance. In addition, the power factor of the BESS converter and the mode of operation of the converter can influence the magnitude of the voltage sag performance improvement.

Multilevel functional principal components analysis (mFPCA) is used to treat dynamical changes in shape in this article. Results of standard (single-level) FPCA are presented here also as a comparison. Monte Carlo (MC) simulation is used to create univariate data (i.e., a single “outcome” variable) that contains two distinct classes of trajectory with time. MC simulation is also used to create multivariate data of sixteen 2D points that represent (broadly) an eye; this data also has two distinct classes of trajectory (an eye blinking and an eye widening in surprise). This is followed-up by an application of mFPCA and single-level FPCA to “real” data consisting of twelve 3D landmark outlining the mouth that are tracked over all phases of a smile. By consideration of eigenvalues, results for the MC datasets find correctly that variation due to differences in groups between the two classes of trajectories variation are larger than variation within each group. In both cases, differences in standardized component scores between the two groups are observed, as expected. Modes of variation are shown to model the univariate MC data correctly, and good model fits are found for both the “blinking” and “surprised” trajectories for the MC “eye” data. Results for the “smile” data show that the smile trajectory is modelled correctly, namely: the corners of the mouth are drawn backwards and wider during a smile. Furthermore, the first mode of variation at level 1 of the mFPCA model show only subtle and minor changes in mouth shape due to sex, whereas the first mode of variation at level 2 of the mFPCA model govern whether the mouth is upturned or downturned. These results are all an excellent test of mFPCA, which show that mFPCA presents a viable method of modelling dynamical changes in shape.

3D facial surface imaging is a useful tool in dentistry and in terms of diagnostics and treatment planning. Between-groups PCA (bgPCA) is a method that has been used to analyse shapes in biological morphometrics, although various “pathologies” of bgPCA have recently been proposed. Monte Carlo (MC) simulated datasets were created here in order to explore “pathologies” of multilevel PCA (mPCA), where mPCA with two levels is equivalent to bgPCA. The first set of MC experiments involved 300 uncorrelated normally distributed variables, whereas the second set of MC experiments used correlated multivariate MC data describing 3D facial shape. We confirmed previous results of other researchers that indicated that bgPCA (and so also mPCA) can give a false impression of strong differences in component scores between groups when there is none in reality. These spurious differences in component scores via mPCA reduced strongly as the sample sizes per group were increased. Eigenvalues via mPCA were also found to be strongly effected by imbalances in sample sizes per group, although this problem was removed by using weighted forms of covariance matrices suggested by the maximum likelihood solution of the two-level model. However, this did not solve problems of spurious differences between groups in these simulations, which was driven by very small sample sizes in one group here. As a “rule of thumb” only, all of our experiments indicate that reasonable results are obtained when sample sizes per group in all groups are at least equal to the number of variables. Interestingly, the sum of all eigenvalues over both levels via mPCA scaled approximately linearly with the inverse of the sample size per group in all experiments. Finally, between-group variation was added explicitly to the MC data generation model in two experiments considered here. Results for the sum of all eigenvalues via mPCA predicted the asymptotic amount for the total amount of variance correctly in this case, whereas standard “single-level” PCA underestimated this quantity.

Pheidole oxyops Forel, 1908 is a generalist ant, which forages actively for plant debris to dead arthropods. In addition, its nest has an entrance that allows the ants gather resources passively by capturing falling preys into the nest. Our objective was to verify if different day periods, temperature and residual soil accumulation (ground pile in the side of nest entrance) could influence the patterns of foraging activity. Foraging activities were registered in the morning, afternoon and twilight. We measured direction and vector of trails, air temperature and humidity during foraging events. Our results showed that foraging routes are independent of residual soil accumulation and other nearby nests. However, air temperature and the time daily period are significant factors to foragers’ exits. Higher air temperatures influenced negatively the exits. In the period of the afternoon, the ants do not show any preference for routes, different from the morning and twilight. In addition, foraging activities were significantly more frequent during twilight period. Leaving the nest at twilight could allow ants foraging in an environment with less exposition to potential predators and competitors. Moreover, it may be also related to opportunism to hunt other nocturnal insects.

This article presents a decentralized phase-shedding technique for multiphase converters. The usual central digital controller is replaced by identical local controllers forming a daisy-chain structure. Phase-shedding decisions are taken locally based on a local inductor current monitoring and threshold crossing management. This control strategy allows to implement as many phases as desired in a modular manner. In order to handle specific events such as load current inrush or a start-up sequence and to guarantee optimal transient responses, additional functions are included into each local controllers. The inter-cell communication protocol is described, along with necessary design considerations of threshold and timing values. Finally, functional simulations are carried out on a 5-leg 12V/1.2V 60W multiphase converter, which validate the proposed decentralized phase-shedding strategy for a microcontroller power supply implementation.

Offshore wind farms are increasingly built in the North Sea and the number of HVDC systems transmitting the wind power to shore increases as well. To connect offshore wind farms to adjacent AC transmission systems, onshore and offshore modular multilevel converters transform the transmitted power from AC to DC and vice versa. Besides, modern wind farms mainly use wind turbines connected to the offshore point of common coupling via voltage source converters. However, converters and their control systems can cause unwanted interactions, referred to as converter-driven stability problems. The resulting instabilities can be predicted by applying an impedance-based analysis in the frequency domain. Considering that the converter models and system data are often confidential and cannot be exchanged in real systems, this paper proposes an enhanced impedance measurement method suitable for black-box applications to investigate the interactions. The proposed method is applied to assess an offshore HVDC system’s converter-driven stability, using impedance measurements of laboratory converters and a wind turbine converter controller replica. The results show that the onshore modular multilevel converter’s interactions with AC grids of moderate short-circuit ratios can lead to instabilities. The offshore system analysis reveals that considering the offshore grid topology is crucial for assessing interactions between the wind turbine controllers and the offshore modular multilevel converter. It is shown that different stability margins result from varying offshore grid layouts.

Reliable and robust control of power converters is a key issue in the performance of numerous technological devices. In this paper we show a design technique for the control of a DC-DC buck converter with a switching technique that guarantees not only good performance but also global stability. We show that making use of the contraction theorem in the Jordan canonical form of the buck converter, it is possible to find a switching surface that guarantees stability but it is incapable of rejecting load perturbations. To overcome this, we expand the system to include the dynamics of the voltage error and we demonstrate that the same design procedure is not only able to stabilize the system to the desired operation point but also to reject load, input voltage and reference voltage perturbations.

The current paper aims to contribute to the literature on community renewable energy by considering two projects developed in the north-west of Italy, in the Piedmont region. The case-studies are analysed by combining two theoretical perspectives: the multilevel perspective and the sociotechnical imaginary approach. On the one hand, applying the first perspective helps reconstruct the context and circumstances that have permitted Piedmont’s energy community projects to emerge. In particular, attention is given to the windows of opportunity created by the passing of the Milleproroghe decree at the national level and by the ensuing regional law 12/2018, which acknowledged the establishment of energy communities in the Piedmont. On the other hand, the sociotechnical imaginary approach allows identifying collective ideas and meanings that emerge when individuals or groups promote a sociotechnical innovation. In our cases, two main future changes are associated with community renewable energy: an integral ecology approach and a stronger sense of community on the one hand, and local development opportunities for rural areas characterised by depopulation, low employment rate and high energy demand, on the other.

In this paper, the authors consider the influence of the type of power supply and the internal parameters of the DC-DC converter on the stability of the system at constant power load. The stability of the system under consideration is important in the design and development of the power supply system for an autonomous consumer. Such a typical system can be a DC microgrid. In the work, when analyzing the stability of the system, the power source is not considered an ideal voltage source, but the active-inductive nature of the voltage source is taken into account, which is equivalent to using a synchronous machine with permanent magnets. The Rauss-Hurwitz algebraic criterion was used as a criterion for analyzing the stability of the system. This will make it possible to build and analyze the areas and boundaries of the system's stability. As a result, the areas and boundaries of the stability of the system were presented. The general trend towards the behavior of the zone of instability of the system was given. At the same time, dependences describing the boundaries of instability are presented, which are combinations of parameters of the DC-DC converter, beyond which the system becomes unstable. The presented definitions of the instability limits can be used as a corrective device of the control system to ensure the stability of the system in the upper limits of the power consumption.

CO2 has characteristic properties and reactions at converter smelting temperature, and the chemical reaction between CO2 and elements such as C and Si in the molten pool has bubble proliferation and cooling effects, which can effectively improve the kinetic and thermodynamic conditions of converter smelting. Here, an experimental study and industrial test on the application of CO2 in converter smelting were carried out. The smelting effects of Mode-1 and Mode-2 with total CO₂ injection amounts of 229 Nm³ and 196 Nm³, respectively, were compared, and the changes in molten steel and slag compositions, dust removal, and gas are analyzed. The test results show that converter top and bottom blowing CO₂ technology (COMI-B)technology had significant metallurgical advantages over the N-Mode; the dephosphorization rate increased by 4.2%, slag (FeO) content was reduced by 2.04%, end point nitrogen content of molten steel was reduced by 20%, gas recovery increased by 8.29 Nm³/t, and soot production reduced by 14.7%. The results of the study provide reference for the application of COMI-B technology in converters in the iron and steel industry and develop a new path for resource utilization of CO₂.

The use of different sources to energize a load is convenient in many applications, particularly those where two or more renewable energy sources are employed as: energy harvesting, hybrid vehicles, and off-grid systems. In these cases, a multi-input converter able to admit sources with different characteristics and, if necessary, select the output power of each source. Several topologies of multi-input converters have been proposed to this aim, however, most of them are based on multi-stage designs, which decreases efficiency and increases control complexity, particularly when more than two sources are used. In this work, a three-input step-up converter easy to control in open loop condition is analyzed. A designed procedure is described, and experimental results are presented for a 1 kW power converter. The implemented converter results in a higher voltage gain, less storage element keeping high efficiency compared to similar topologies. Using the procedure here proposed, this converter that was initially proposed for photovoltaic applications is enabled to be used in medium and high-power applications, for example when renewable energy sources are used.

Recently, resistive random access memory (RRAM) has been an outstanding candidate among various emerging nonvolatile memories for high density storage and in-memory computing applications. However, the traditional RRAM, which accommodates two states depending on applied voltage, cannot meet the high density requirement in the era of big data. Many research groups have demonstrated that RRAM possesses the possibility of multi-level cell to overcome the demand of mass storage. Among numerous semiconductor materials, gallium oxide, as the fourth-generation semiconductor material, is highly-profile due to its excellent material proper-ties, and already be widely used in optoelectronics, high-power, resistive switching device and so on, due to its wide bandgap and transparent properties. In this study, we have successfully demonstrated the Al/GO/Ga2O3/ITO RRAM to achieve the possibility of two-bit storage. Compared to the single-layer counterpart, the bilayer structure has excellent electrical properties and stable reliability. The endurance characteristics could be enhanced above 100 switching cycles with an ON/OFF ratio of over 103. Moreover, the filament models are also described in this thesis to clarify the transport mechanisms.

A three-phase multilevel inverter (MLI) synthesized with 31-levels in the output voltage is used to provide ac supply to a three-phase, squirrel-cage induction motor. The gating angles required for thirty power switches in MLI are optimized by both Genetic Algorithm (GA) and Gray Wolf Op-timization (GWO). In the optimization technique, the optimal angles are determined by solving the trigonometric equations from the Fourier analysis for targeting minimum total harmonic distortion (THD) at the MLI output. Simulation model and experimental prototype are developed for performance analysis and validation. The results obtained demonstrate that the MLI is effec-tively able to produce 31-levels of three-phase ac output voltages with THD not exceeding 5% when loaded with a resistive load and a three-phase induction motor. The voltages and currents are measured and recorded for different loads and operating conditions, including the amount of energy consumed by the loads, as well as frequency analysis, which shows the absence of most of the triple harmonics that have a negative impact on the efficiency of the inverter.

The present article analyzes the connection between, on the one hand, gender equality and, on the other hand, loneliness and social isolation. It hypothesizes that modern relational institutions, that support gender equality, such as no-fault divorce laws, reduce loneliness in close relationships. This hypothesis is put to the test through a multilevel analysis of the ISSP 2017. The analysis reveals that the data agrees, to a large extent, with the theoretical arguments. The prevalence of loneliness is higher in countries with higher levels of gender inequality (as measured by the Gender Inequality Index [GII]). This can be attributed to a moderation effect: at lower levels of gender inequality, partnerships provide better protection from loneliness. These results are robust to controls for demographic composition, level of health, educational attainment, income poverty, and interview mode. Last, the analyses show that the threat of emotional isolation is more widespread in countries with low gender inequality. This finding, however, is only significant before controlling for demographic composition, level of health, educational attainment, income poverty, and interview mode, and it requires further analysis. The concluding section relates these findings to the popular tendency to argue that modern society has created a “loneliness epidemic.”

This paper proposes a single-stage asymmetrical half-bridge fly-back (AHBF) converter with resonant mode using dual-mode control. The presented converter has an integrated boost converter and asymmetrical half-bridge fly-back converter and operates in resonant mode. The boost-cell always operates in discontinuous conduction mode (DCM) to achieve high power factor. The presented converter operates simultaneously using a variable-frequency-controller (VFC) and pulse-width-modulation (PWM) controller. Unlike the conventional single-stage design, the intermediate bus voltage of this controller can be regulated depending on the main power switch duty ratio. The asymmetrical half-bridge fly-back converter utilizes a variable switching frequency controller to achieve the output voltage regulation. The asymmetrical half-bridge fly-back converter can achieve zero-voltage-switching (ZVS) operation and significantly reduce the switching losses. Detailed analysis and design of this single-stage asymmetrical half-bridge fly-back converter with resonant mode is described. A wide AC input voltage ranging from 90 to 264 Vrms and output 19 V/ 120 W prototype converter was built to verify the theoretical analysis and performance of the presented converter.

In the context of cognitive radio, smart city and Internet-of-Things, the need of advanced radio spectrum monitoring becomes crucial. However, surveillance of a wide frequency band without using extremely expensive high sampling rates devices is a challenging task. The recent development of compressed sampling approaches offers a promising solution to these problems. In this context, the Modulated Wideband Converter (MWC), a blind sub-Nyquist sampling system, is probably the most realistic approach and was successfully validated in real-world conditions. The MWC can be realized with existing analog components and there exist calibration methods which are able to integrate the imperfections of the mixers, filters and ADCs, hence allowing its use in real-world. The MWC underlying model is based on signal processing concepts such as filtering, modulation, Fourier series decomposition, oversampling and undersampling, spectrum aliasing, and so on, as well as in-flow data processing. In this paper we develop an MWC model which is entirely based on linear algebra, matrix theory and block processing. We show that this approach has many interests: straightforward translation of mathematical equations into simple and efficient software programming, suppression of some constraints of the initial model, and providing a basis for the development of an extremely fast system calibration method. With a typical MWC acquisition device we obtained a speed up of a factor greater than 20 of the calibration computation time, compared with a previous implementation.

This paper examines the moral community thesis in the secular context of China. Using multilevel logistic regression, we test (1) whether both individual- (measured by affiliation with institutional religion) and aggregate-level religiosity (measured by the number of religious sites per 10,000 people in province) are inversely related to law and rule violations at the individual level and (2) whether the province-level religiosity enhances the inverse relationship between individual religiosity and the deviant behaviors. Results from analyzing data from the 2010 China General Social Survey and the Spatial Explorer of Religions show that both individual- and aggregate-level religiosity are inversely related to the odds of violating the law and various rules of government, transportation, workplace, and other organizations. However, the cross-level interactions are not significant across models, indicating that the contextual religiosity does not increase the effect of individual-level religiosity on deviance. Implications of findings for the moral community thesis are discussed.

This paper introduces a structured design for an effective power-sharing technique among converter-interfaced distributed generation (DG) units within a microgrid that operates without a synchronous generator. The proposed power-sharing technique leverages the battery energy storage system (BESS) to promptly respond to network changes. The real power output of each commercial distributed energy resources (CDER) unit is governed by a frequency-droop characteristic and a complementary frequency restoration strategy. Deloading techniques are employed by solar and wind power generators to enhance response during power supply or demand disturbances. To ensure microgrid stability, small-signal analysis is conducted for controller design, including the determination of stability margins. Initial tuning of the power-sharing technique parameters is achieved using the Ziegler-Nichols Method, followed by further optimization through a meta-heuristical algorithm to enhance the response time of energy sources. The proposed power-sharing technique's performance is evaluated on a benchmark medium voltage network using industry-standard commercial software. The test results demonstrate the precise and rapid power-sharing capabilities among DGs facilitated by the proposed technique, highlighting its effectiveness in dynamic microgrid environments.

Accurate forecasts of ocean waves energy can not only reduce costs for investment but it is also essential for management and operation of electrical power. This paper presents an innovative approach based on the Long Short Term Memory (LSTM) to predict the power generation of an economical wave energy converter named “Searaser”. The data for analyzing is provided by collecting the experimental data from another study and the exerted data from numerical simulation of searaser. The simulation is done with Flow-3D software which has high capability in analyzing the fluid solid interactions. The lack of relation between wind speed and output power in previous studies needs to be investigated in this field. Therefore, in this study the wind speed and output power are related with a LSTM method. Moreover, it can be inferred that the LSTM Network is able to predict power in terms of height more accurately and faster than the numerical solution in a field of predicting. The network output figures show a great agreement and the root mean square is 0.49 in the mean value related to the accuracy of LSTM method. Furthermore, the mathematical relation between the generated power and wave height was introduced by curve fitting of the power function to the result of LSTM method.

This paper presents the design of a high frequency zero voltage switching (ZVS) full-bridge converter with a phase-shifted driving signal for photovoltaic applications. The resonant power converter can provide high-power capacity under high-frequency operation. The proposed power converter can also reduce the size of the transformer under the same power rating. The high-frequency transformer was developed by using the resonant and switching frequencies of the power converter to reduce the switching loss and to improve the system efficiency. Phase-shifted modulation was selected to drive the switches of a full-bridge power converter based on the switching loss minimization method. The desired output voltage was controlled using a closed-loop controller under a loop gain stability margin. The simulation results showed that the output voltage can be controlled to the desired constant when the input voltage changes from 30 VDC to 60 VDC. The desired output voltage of power converter is constant at 400 VDC. The power converter can transfer the DC supply to a 220 VAC household via grid-connected inverter. Therefore, the proposed study showed the effectiveness of the phase-shift ZVS full-bridge power converter with high-frequency transformer. This power converter can control the operation of the desired voltage system and has a small sizing of power converter system, low switching loss, and high system efficiency.

Power converters with coupled inductors are very promising due to the high efficiency and high voltage gain. Apart from the aforementioned advantages, the boost-flyback converter reduces the voltage stress on the semiconductors. However, to obtain good performance with high voltage gains, the controller must include two control loops (current and voltage), and a compensation ramp. One of the most used control techniques for power converters is the peak current-mode control with compensation ramp. However, in the case of a boost-flyback converter there is no mathematical expression in the literature, to compute the slope of the compensation ramp. In this paper, a formula to compute the slope of the compensation ramp is proposed in such a way that a stable period-1 orbit is obtained. This formula is based on the values of the circuit parameters, such as inductances, capacitances, input voltage, switching frequency and includes some assumptions related to internal resistances, output voltages, and some other electrical properties related with the physical construction of the circuit. The formula is verified numerically using the saltation matrix and experimentally using a test circuit.

Based on Venturini method, it is in favor of the modulation technique for controlling the matrix converter due to only use of the comparison between the duty cycles in time domain and the triangular carrier wave for generating the gating signals and the achievable voltage ratio between fundamental output magnitude and fundamental input magnitude to 0.866. However, even with simple modulation method and achieving maximum fundamental output magnitude, the possible input voltage unbalance conditions accordingly influence on the output performances (more reduction and distortion). Thus, a modified Venturini modulation method is presented in this paper, in order to solve the problems of unbalanced input voltage conditions on the matrix converter performances. The proposed strategy is to satisfy the desirable feature of the duty cycle modulating waves, as generated in the event of normal situation. Up to this approach, it can support either single-phase condition or two-phase condition. Performance of the proposed control strategy was verified by the simulated implementation in the MATLAB/Simulink software with showing good steady-state and dynamic operations.

This paper introduces a sliding mode control (SMC) based equivalent control method to a novel high output gain Cuk converter. An additional inductor and capacitor improves the efficiency and output gain of the classical Cuk converter. Classical PI controllers are widely used in DC-DC converters. However, it is a very challenging task to design a single PI controller operating in different load and disturbances. SMC based equivalent control method which achieves a robust operation in a wide operation range is also proposed. Switching frequency is kept constant in appropriate interval in different loading and disturbance conditions by implementing a dynamic hysteresis control method. Numerical simulations conducted on Matlab/Simulink confirm the accuracy of analytical analysis of high output gain modified Cuk converter. In addition, proposed equivalent control method is validated in different perturbations to demonstrate the robust operation in wide operation range.

Background/Purpose: Over the last two decades, malaria has remained a major worldwide public health concern, especially in the developing countries leading to high morbidity and mortality among children. Nigeria is the world most burdened malaria endemic nation, contributing more than a quarter of global malaria cases. This study determined the prevalence of malaria among children 6-59 months in Nigeria, and the effects of individual and contextual factors. Methods: The study utilized data from 2018 Nigeria Demographic and Health Survey (NDHS) involving a weighted sample size of 10,185 children who were tested for malaria using rapid diagnostic test (RDT). Given the hierarchical structure of the data set, such that children at level-1 are nested in community at level-2, and nested in states and Federal Capital Territory (FCT) at level-3, multilevel mixed effect logistic regression models were used for the analysis. Results: The proportion of children 6-59 months of age in Nigeria that had malaria fever positive as assessed by RDTs was 35.5% (3,418/10185), (CI: 33.9-37.1). Kebbi State had the highest proportion of children 6-59 months who were malaria positive, 77.6%, (CI: 70.2-83.5), followed by Katsina State, 55.5%, (CI: 47.7-63.1). The Federal Capital Territory (FCT), Abuja had the proportion of 29.6%, (CI: 21.6-39.0), malaria positive children of 6-59 months of age. Children between the age of 48 and 59 months were 2.68 times more likely to have malaria fever than children 6-11 months of age (AOR=2.68, 95% CI: 2.03-3.54). Also, children from the rural area (AOR= 2.12, 95% CI: 1.75-2.57), were more likely to suffer from malaria infection compare with children from urban area. Conclusion: The study identified some individual and contextual predictors of malaria among children in Nigeria. These factors are areas that need to be considered for policy designs and implementations toward control and total elimination of malaria-related morbidity and mortality among children in Nigeria.

Cervical fusion has been a standard procedure for treating the abnormalities associated with the cervical spine. However, the reliability of anterior cervical discectomy and fusion (ACDF) has become arguable due to its adverse effects on the biomechanics of adjacent segments. One of the drawbacks associated with ACDF is adjacent segment degeneration (ASD) which has served as the base for the development of dynamic stabilization systems (DSS) and total disc replacement (TDR) devices for cervical spine. However, the hybrid surgical technique has also gained popularity recently but their effect on the biomechanics of cervical spine is not well researched. Thus, the objective of this FE study was to draw the comparison among single, bi-level and hybrid surgery with DCI implant with traditional fusion. Reduction in range of motion (ROM) for all the implanted models was observed for all the motions except extension, compared to intact model. The maximum increase in ROM of 42% was observed at C5-C6 level in Hybrid-DCI model. The maximum increase in adjacent segment’s ROM of 8.7% was observed in multilevel fusion model. The maximum von Mises stress in the implant was highest for the multilevel DCI model. Our study also showed that the shape of DCI implant permits flexion/extension relatively more compared to lateral bending and axial rotation.

This paper proposes a novel symmetrical active-switched coupled-inductor high-step-up DC/DC converter. A new active-switched coupled inductor is used to allow much higher voltage gain of the proposed converter. The symmetrical circuit structure of the proposed converter evenly divides large input currents and reduce input current ripple by operating in interleaved mode so power density is increased. The switches also have low voltage stress. The operating principle and design considerations for the converter topology are described. The proposed converter with an input voltage of 40 V, an output voltage of 400 V and an output of 1000 W at a switching frequency of 50 kHz is implemented. The simulations and experimental results are thus depicted to verify the theoretical analysis. The highest efficiency is 95.5% at 200 W measured by using a HIOKI 3390. Consequently, the proposed converter is suitable for renewable energy generation systems that require high power, high voltage gain and high efficiency.

With the widespread application of Voltage Source Converter (VSC) in the power system with high penetration of renewable resources, the problem of wideband oscillations caused by the interaction between the power converters and the power grid has drawn large attention. This paper presents a new methodology for simplifying the mathematical derivations of the impedance model of VSC. Using the new simplified model, the stability and the spectrum characteristic of the performance of the VSC can be clearly analyzed. The proposed second-order d-q impedance model of the grid connected VSC at presence of PLL, not only mathematically proves that the wideband oscillatory modes always occurs in conjugate pairs, but also deliver a clear vision of the physical essence of the wideband oscillations. The classic modal analysis is executed in the paper to demonstrate the stability and frequency spectral characteristics of the wideband oscillations in the VSC integrated system. The impact of control parameters of the VSC on the wideband oscillatory stability is thouroughly analyzed using the results of the modal analysis. The methodology can be considered a powerful tool for the control design of VSC in the modern power system.

Various renewable energy sources such as wind power and photovoltaic (PV) have been increasingly integrated into the power system through power electronic converters in recent years. However, power electronic converter-driven stability issues under specific circumstances, for instance, modal resonances might deteriorate the dynamic performance of the power systems or even threaten the overall stability. In this paper, the integration impact of a hybrid renewable energy source (HRES) system on modal interaction and converter-driven stability is investigated in an IEEE 16-machine 68-bus power system. Firstly, an HRES system is introduced, which consists of full converter-based wind power generation (FCWG) and full converter-based photovoltaic generation (FCPV). The equivalent dynamic models of FCWG and FCPV are then established, followed by the linearized state-space modeling. On this basis, converter-driven stability analyses are performed to reveal the modal resonance mechanisms of the interconnected power systems and the modal interaction phenomenon. Additionally, time-domain simulations are conducted to verify effectiveness of dynamic models and support the converter-driven stability analysis results. To avoid detrimental modal resonances, an optimization strategy is further proposed by retuning the controller parameters of the HRES system. The overall results demonstrate the modal interaction effect between external AC power system and the HRES system and its various impacts on converter-driven stability.

A modular switched-capacitor (SC) DC-DC converter (MSCC) is introduced in this paper. It is designed to boost a low input voltage to a high voltage level and can be applied for photovoltaics and electric vehicles. This topology has high extensibility for high voltage gain output. The merits of the converters also lie in the fault tolerance operation and the voltage regulation with a minimum change in the duty ratio. Those features are built in when designing the modules and then integrating these into the DC-DC converter. Converter performance including voltage gain, voltage and current stress are focused and tested. The converter is modelled analytically, and its control algorithm is analyzed in detailed. Both simulation and experiment are carried out to verify the topology under normal operation and fault mode operation.

This paper presents a new high-efficiency-high-step-up based converter integrating two stype DC-DC Boost and Flyback coupled magnetic converter with recovery stage dedicated to smart HVDC distributed architecture in renewable energy production systems. Appropriate duty cycle ratio assumes that the recovery stage work with parallel charge and discharge to achieve high step-up voltage gain. Besides, the voltage stress on the main switch is reduced with a passive clamp circuit and thus, low on-state resistance Rdson of the main switch can be adopted to reduce conduction losses. The circuit is simple to control. As a final point of this research, the simulation and the prototype investigational results are presented to demonstrate the effectiveness of this proposed converter.

Three-phase to single-phase matrix converter (TSMC) is used as the transmitter for transient electromagnetic method (TEM) instrument, instead of an AC-DC converter and an H-bridge inverter. The transmitter produces excitation current for primary field. The output current has a waveform with a bipolar square of half duty cycle, which is required by TEM. The space vector PWM based on input currents is discussed in detail. The control method of input power factor is proposed for TSMC. The simulation model of TSMC is established and the simulations of different conditions are completed. The simulation results show the controllability of the input power factor is illustrated.

Background: The aim of our study was to analyze the effect of socioeconomic inequalities, both at the individual and area of residence levels, on the probability of COVID-19 confirmed infection, and its variations across three pandemic waves. Methods: Retrospective cohort study. We included data from all individuals tested by COVID-19 during the three waves of the pandemic, from March to December 2020 (357,989 individuals). We studied the effect of inequalities on the risk of having a COVID-19 confirmed diagnosis after being tested using multilevel analyses with two levels of aggregation: individuals and basic healthcare area (BHA) of residence (deprivation level and type of zone). Results: Patient profile changed through the pandemic, with a predominance of low-paid employees living in deprived BHA. Workers with low salaries, unemployed and people on minimum integration income or who no longer receive the unemployment allowance, had a higher probability of COVID-19 infection than workers with salaries ≥€18,000 per year. Inequalities were higher in women and in the second wave. The deprivation level of BHA of residence influenced the risk of COVID-19 infection, especially in the second wave. Conclusions: There are inequalities in the risk of COVID-19 confirmed infection, both at individual and area level. It is necessary to develop individual and area coordinated measures in the control, diagnosis and treatment of the epidemic, in order to avoid an increase in the already existing inequalities.

Membranes based on sulfonated synditoactic polystyrene were thoroughly characterized by contrast variation SANS over a wide Q-range in dry and hydrated states. The film samples were prepared by solid-state sulfonation that allowed a uniform sulfonation of only the amorphous phase while preserving the crystallinity of the membrane. The samples were loaded with different guest molecules in either the amorphous (fullerenes) or the crystalline (toluene) regions, in order to vary the neutron contrast or to reproduce the conditions enabling an increased resistance of the membranes to chemical decomposition. The use of uni-axially deformed film samples and contrast variation with different H2O/D2O mixtures allowed for the identification and characterization of different structural levels with sizes between nm and μm, which form and evolve in the membrane morphology in dry and hydrated states and produce scattering features on different detection sectors and at different detection distances after the sample, depending on their size and orientation.

This paper presents a hydrodynamic numerical model for a pitching wave energy converter (WEC). The model uses potential wave theory and is based on Cummins' equation, with nonlinear hydrostatic restoring stiffness and excitation forces based on instantaneous body position and water surface elevation. The numerical model can include non-linear forces, like quadratic drag, power-take-off and other forces that may account for unknown viscous effects observed in experiments. The paper discusses the applicability and limitations of the code and presents the cases where assumptions and simplifications can be made. The goal is to conclude on the simplest, yet accurate, version of the model by evaluating its accuracy using experimental data. The case study for validation is Floating Power Plant's (FPP's) WEC [1]. In the full-scale commercial project, FPP's device consists of a semisubmersible platform hosting a wind turbine (5-8MW) and 4 WECs, each one connected to the platform by a rotation shaft. Due to the configuration of the platform, strong interactions occur between the WECs and the structure, as they are very closely spaced. In order to validate a numerical model able to simulate these hydrodynamic interactions, wave basin experiments with a similar but simplified setup were performed.

This article presents a self balanced multistage DC-DC step-up converter for photovoltaic applications. Proposed converter topology is designed for unidirectional power transfer and provides a doable solution for photovoltaic applications where voltage is required to be stepped up without magnetic components (Transformer-less and Inductor-less). The output voltage obtained from renewable sources will be low and must be stepped up by using a DC-DC converter for photovoltaic applications. K diodes and K capacitors along with two semiconductor control switch are used in the K-stage proposed converter to obtain an output voltage which is (K+1) times the input voltage. The conspicuous features of proposed topology are i) Magnetic components free (Transformer-less and Inductor-less). ii) Continuous input current iii) Low voltage rating semiconductor devices and capacitors iv) Modularity v) Easy to add a higher number of levels to increase voltage gain vi) Only two control switches with alternating operation and simple control. The proposed converter is compared with recent existing transformer-less and Inductor-less power converter in term of voltage gain, number of devices and cost. The application of proposed circuit is discussed in detail. The proposed converter has been designed with rated power of 60W, input voltage is 24V, output voltage is 100V and switching frequency is 100 kHz. The performance of the converter is verified through experimental and simulation results.

In this paper, a buck DC-DC converter with the proposed twin frequency control scheme (TFCS) and accurate load current sensing (ALCS) have been designed and implemented with 0.18µm CMOS technology for a supply voltage ranging from 2.0-3.0V which is compatible with state-of-the-art batteries (NiCd/NiMH: 1.1-2V, Li-Ion: 2.5-4.2V). The proposed converter yields a peak efficiency of about 92.7% with a load current of 30mA. Furthermore, it only occupies a silicon area of 1.3mm2. The proposed buck converter is dedicated for smartphone applications whereby it spends most of its time in idle, low load conditions.

In this paper, a fuzzy logic-based energy management system and multi-port quasi-z-source converter are proposed that utilizes hybrid renewable energy sources. The system ensures that each energy source module can be used individually by employing fuzzy logic to define power modes. This approach also helps prevent switching losses resulting from extra switching of the source modules. Also, the proposed energy management does not have a mathematical model, so applicability is simple and it is suitable for different multiple input topologies. The Mamdani fuzzy inference system can be designed to capture the nonlinear behavior of the system because of the linguistic rules. Moreover, by adopting the quasi-z-source network to the end of the multi-port converter, the switching losses of the multi-port modules have been significantly reduced. The simulation results are obtained using MATLAB Simulink, and the experimental results are obtained by connecting the circuit to MATLAB Simulink via an Arduino Due.

This paper presents a control algorithm for soft-switching series LC converters. The conventional voltage-to-voltage controller is split into a master and a slave controller. The master controller implements constant-current-constant-voltage (CCCV) control, required for demanding applications, i.e. lithium battery charging or laboratory power supplies. It defines the set-current for the open-loop current slave controller, which generates the PWM parameters. The power supply achieves fast large-signal responses, e.g. from 5 V to 24 V, where 95% of the target value is reached in less than 400 µs. The design is evaluated extensively in simulation and on a prototype. A consensus between simulation and measurement is achieved.

The article presents the results of tests related to failure analysis and finding ways to diagnose used semiconductor elements, among other, in power electronics converter systems on vessels and offshore facilities (drilling and production rigs, wind turbines). Diagnostic relationships were found between the temperature change in the above systems and the signals generated in form of elastic waves of acoustic emission.

A high step-up DC-to-DC converter that integrates an isolated transformer and a switched-clamp capacitor is presented in this study. The voltage stress of the main power switch should be clamped to 1/4 V by using the turn ratio and switched-clamp capacitor of an isolated transformer to achieve a high voltage gain. In addition, a passive clamp circuit is employed reduce voltage stress on the main power switch. The energy of the leakage inductor can be recycled by the clamp capacitor because of the passive clamp circuit, thereby improving the power converter efficiency. The converter consists of one isolated transformer, one main switch, three capacitors, and four diodes. Operating principle and steady-state analyses are also discussed. Finally, a 24-V-input voltage to 200-V-output voltage and a 150 W output power prototype converter are fabricated in the laboratory. The maximum efficiency of the converter is 95.1 at 60 W.

The purpose of this study was to identify the factors that affect the mortality among adult HIV/TB co-infected patients and to see the nutritional difference among mortality in residence level. Retrospective cohort studies of 417 patients which fulfill our criteria were included. Multilevel logistic regression models were used. MLwiN and SPSS software are used to estimate the parameter. The variance of the random factor in the empty model was significant which indicates that there were residential differences in TB-HIV co-infected mortality and it shows multilevel analysis was an appropriate approach for further analysis. The prevalence of HIV/TB co-infected patients' death was 12.9% in study time. Functional status, age of patients, WHO clinical stages, nutritional status, CD4 counts, regimen, and BMI were found to be significant determinants of HIV/TB co-infected mortality. In our study, patients with the bedridden category of functional status, the fourth stages of WHO clinical stages (stage IV), patients with higher age, patients whose treatments were second-line regimen and low CD4 cell counts were more at risk of death. The study also revealed that; poor nutritional status increased the risk of mortality among HIV/TB co-infected patients and it varies among the residence of the patients (rural area were more at risk).

The integrated DC-DC converter is appropriate for use in many domains, namely, display, cellular, and portable applications. This paper presents an integrated monolithic voltage-mode DC-DC boost converter with a low-power control circuit. The driver circuit requires an integrated converter to power up a digital logic circuit and converts the unregulated DC input to the controlled DC output at the desired voltage level. It is the integration of both power switches and control circuitry within the same CMOS technology to buck down and boost voltages using a switch mode regulator. In order to increase power efficiency in the DC-DC boost converter that provides low-power operation with a small chip size, a low-voltage operation is applied to the unique circuit characteristic. The operational transconductance amplifier(OTA), comparator, and oscillator in the control circuit are designed with the supply voltage of 3.3V and the operating frequency of 5.5 MHz. A compensator is used to create a pole that has sufficient phase margin for high stability. The DC- DC boost converter is measured in both experiment and simulation. Testing of the proposed circuit on the 0.35μm CMOS process shows that the output transient time of the amplifier can be controlled within of 7μsec and the output voltage is accurately controlled with a ripple ratio of 3%.

High-performance motor drives that operate in harsh conditions require an accurate and robust angular position measurement to correctly estimate the speed and reduce the torque ripple produced by angular estimation error. For that reason, a resolver is used in motor drives as a position sensor due to its robustness. A resolver-to-digital converter (RDC) is an observer used to get the angular position from the resolver signals. Most RDCs are based on angle tracking observers (ATOs). On the other hand, generalized predictive control (GPC) has become a powerful tool in developing controllers and observers for industrial applications. However, no GPC-based RDC with zero steady-state error during constant speed operation was proposed. This paper proposes an RDC based on a second-order difference GPC (SOD-GPC). In SOD-GPC, the second-order difference operator is applied to design a GPC model with two embedded integrators. Thus, the SOD-GPC is used to design a type-II ATO whose steady-state angle estimation error tends to zero during constant speed operation. Simulation and experimental results prove that the proposed RDC system has better performance than other literature approaches.

Intended for the high voltage gain and wide-range operation of DC/DC converters for photovoltaic energy storage systems, a topology for four-phase interleaved DC/DC converters for photovoltaic power generation is proposed. This topology increases output voltage for output in series, and reduces the input current ripple by paralleling the input. Compared with traditional boost converter topology, the proposed topology reduces the output current and output voltage ripple, reduces the stress of the switching device, and reduces the withstanding voltage of the output capacitor under the premise of ensuring the boost ratio. Experimental results show that the maximum efficiency of the converter reaches 95.37%. Compared with traditional boost converters, the proposed converter offers obvious advantages in efficiency under the conditions that the output voltage and load are variable.

The management of the electrical energy still raises a huge interest for end-users at the household level. Home electricity management systems (HEMS) have recently emerged both to warrant uninterruptible power and high power quality, and to decrease the cost of electricity consumption, by either shifting it in off peak time or smoothing it. Such a HEMS requires a bidirectional DC-AC converter, specifically when an energy transfer is required between a storage system and the AC-grid, and vice versa. This article points out the relevance of an innovative topology based on sinusoidal waveforms from the generation of sine half-waves. Such a topology is based on a DC-DC stage equivalent to an adjustable output voltage source and a DC-AC stage (H-bridge) which are in series. The results of a complete experimental procedure prove the feasibility to improve the power quality of the output signals in terms of total harmonic distortion (THD-values about 5%). The complexity of the proposed converter is minimized in comparison with multilevel topologies. Finally, wide band-gap semiconductor devices (SiC MOSFETs) are helpful both to warrant the compactness and the high efficiency (about 96%) of the bidirectional converter, whatever its operation mode (inverter or rectifier mode).

The paper deals with an electrothermal model of a thermoelectric converter dedicated to performing simulations of coupled thermal and electrical phenomena taking place in harvesting processes. The proposed model is used to estimate the electrical energy gain from waste heat that would be sufficient to supply electronic circuits, in particular autonomous battery-less nodes of wireless sensor networks (WSN) and Internet of Things (IoT) devices. The developed model is not limited to low power electronic solutions such as WSN or IoT; it can also be scaled up and applied to simulations of considerably higher thermal power conversion. In the paper, a few practical case studies are presented that show the feasibility and suitability of the proposed model for complex simultaneous simulation processes, in both electrical and thermal domains. The first example deals with a combined simulation of the electrothermal model of a thermoelectric generator (TEG) and an electronic harvester circuit based on Analog Devices’ power management integrated circuit LTC3108. The second example relates to the thermalization effect in heat sink-less harvesting applications that could be mitigated by a pulse mode operation.

The power converter is the significant device in a wind power system. Wind turbine will be shut down and off grid immediately with the occurrence of the IGBT module open-circuit fault of power converter, which will seriously impact the stability of grid and even threaten personal safety. However, in the existing diagnosis strategies of power converter, there are few single and double IGBT modules open-circuit fault diagnosis methods producing negative results including erroneous judgment, omissive judgment and low accuracy. In this paper, a novel method to diagnose the single and double IGBT modules open-circuit faults of the permanent magnet synchronous generator (PMSG) wind turbine grid-side converter (GSC) is proposed. Above all, collecting the three-phase current varying with wind speed of 22 failure states including a normal state of PMSG wind turbine GSC as the original signal data. Afterward, the original signal data are decomposed by using variational mode decomposition (VMD) to obtain the mode coefficient series, which are analyzed by the proposed method base on fault trend feature for extracting the trend feature vectors. Finally, the trend feature vectors are used as the input of deep belief network (DBN) for decision-making and obtaining the classification results. The simulation and experimental results show that the proposed method can diagnose the single and double IGBT modules open-circuit faults of GSC, and the accuracy is higher than the benchmark models.

This paper presents a proposal for a non-isolated bidirectional converter (NIBC) controlled by a deep neural network (DNN) to enable vehicle-to-vehicle (V2V) and vehicle-to-grid (V2G) charging, which contributes to the development of more efficient and sustainable transportation and energy systems. The DNN controller manages power flow in both directions, making it possible to charge electric vehicles (EVs) and discharge power from EVs to the grid with improved efficiency and performance compared to traditional control methods. The non-isolated topology used in this proposal offers several benefits, including reduced cost, smaller size, and higher efficiency. To train the DNN controller, a large dataset of simulations was used, and the results were validated with a hardware setup. The real-time performance of the DNN controller was compared to a proportional-integral (PI) based controller through simulated results. The findings of the study show that the DNN controller outperforms traditional PI controllers.

This article discusses a transformer-free, high-efficiency DC-DC converter besides renewable energy applications. The traditional buck-boost, classic Zeta, Sepic, and Cuk converter does have the benefits of a simple design, low cost, as well as the capacity to execute voltage step-up and step-down. Conversely, because of the detrimental consequences of the parasitic constraints of the device, the voltage conversion gain of the traditional DC-DC converter is much more restricted and the efficiency is also significantly smaller, whereas this proposed converter does have a higher voltage gain and efficiency because it is used in a single power switch, resulting in reduced switching losses and voltage stress. The said converter's design is very simple, which simplifies the operation control and reduces switching and conduction losses, leading to an efficiency of 97.4 percent. This converter seems to have the same capabilities as the Zeta converter, including continuous desired output current and desired buck-boost operation. Such an article offers the operation principle and steady evaluation, as well as a comparison with other existing high step-up configurations. The proposed converter employs a fuzzy logic controller, which improves the voltage level as well as reduces the time taken to set the voltage output of a conventional PI and ANN controller, especially in comparison to the FLC controller. For deployment, Experimental Result and MATLAB/Simulink has been used, and the modeling results indicate that the proposed controller performance has improved

This article deals with the denoising of signals from sensors (current and voltage) in a photovoltaic conversion chain using wavelet theory. The idea is to reduce the noise as much as possible without distorting or losing the original signal information. To see the reliability of this proposed method, a comparative study between our proposed method (WDD) and the classic low-pass filter method was presented. The contribution in this work is the improvement of the DC-DC boost converter via the use of wavelet theory, however, that’s why we set two objectives: the first is to obtain reliable control of the DC-DC boost converter via the proposed WDD and the second to increase the overall system efficiency. The experimental results show a very great improvement in the quality of the signals of the proposed method compared to the classic method of filtering by low-pass filter.

Visualization has always been a crucial part of the educational process. Implementing computer algorithms and virtual reality tools into it is vital for the new generation engineers, scientists and researchers. In the field of chemistry education, various software that allow dynamic molecular building and viewing are currently available. These software are now used to enhance the learning process and ensure better understanding of the chemical processes from the visual perspective. The present short communication provides a summary of these applications based on the NarupaXR program, which is a great educational tool that combines the functionality and simple design necessary for an educational tool. NarupaXR is used with a companion application “Narupa Builder'' which requires a different file format, therefore a converter that allows a simple transition between the two extensions has been developed. The converter sufficiently increases the efficiency of the educational process. The automatic converter is freely available on GitLab (https://gitlab.com/teamSCAMT/converter_mol2_to_xml). The current communication provides detailed written instructions that can simplify the installation process of the converter and facilitate the use of both the software and the hardware of the VR set.

Plasma generation by means of electrical discharge requires specialized power supply systems. The applicability of plasma for various plasma processes depends on its parameters, and these in turn depend on the parameters of the power supply systems. Arc plasma can be unstable, generating a lot of electromagnetic interference and overvoltage and overcurrent. The power system of a plasma reactor must guarantee good plasma control characteristics, be immune to disturbances and ensure good cooperation with the power grid. The article analyzes the cooperation of a three-phase plasma reactor, with gliding arc discharge, with a power supply system of a new type. This system integrates an AC/DC/AC converter with a five-column transformer of special design in a single device. Using the properties of magnetic circuits, it was possible to integrate the functions of ignition and sustaining the burning of the discharge in the reactor in a single transformer. Proper design of the transformer is crucial to achieve good cooperation of the AC/DC/AC converter with both the plasma reactor and the power supply network. The presented power supply design shows a number of positive features predisposing it to powering arc plasma reactors.

This paper proposes an approach to estimate the parameters of an AC-DC boost power factor corrector converter which includes an EMI filter. To this end, once the topology is known, measurements at the input and output terminals of the converter are done to identify the values of the passive elements. The proposed methodology is based on the trust-region nonlinear least squares algorithm to identify the parameters of the converter. The steady-state and the transient signals of the converter at the input/output terminals are acquired non-intrusively without any internal modification of the circuitry. The accuracy of the parameter identification carried out is determined by comparing the estimated values with the actual values provided by the manufacturer, and by contrasting the measured signals with the ones obtained with a simulation model with the estimated values of the parameters. The results presented in this paper prove the accuracy of the proposed approach, which can be extended to other power converters and filters.

Implementing computer algorithms and virtual reality tools into all areas of the educational process is vital for the new generation engineers, scientists and researchers. With regards to chemistry education, various software that allow dynamic molecular building and viewing are currently available. The present short communication provides a summary of these applications and a detailed description of the NarupaXR program, which has the desired mix of functionality and simple design, necessary for an educational tool. Since NarupaXR can only be used with a companion application “Narupa Builder” which has a different file format, we have developed a converter that allows a simple transition between the two extensions of the aforementioned programs and sufficiently increases the efficiency of the educational process. The automatic converter is freely available on GitLab (https://gitlab.com/teamSCAMT/converter_mol2_to_xml). We have provided this short communication with detailed written instructions that can simplify the installation process of the converter and facilitate the use of both the software and the hardware of the VR set.

Chaotic switching is a newly evolve randomization method which can suppress conducted electromagnetic interference generated within the DC-DC converter. It can suppress the spectral peaks present in the frequency band effectively by spread spectrum technique and can spread it over the wide range of frequency band implying EMI suppression. In this paper, a chaotic PWM technique based on RCFMFD scheme is generated through Field programmable gate array (FPGA) for suppressing the conducted electromagnetic interference (EMI) generated within the Luo converter. A hardware prototype of Luo converter was developed in order to analyze EMI reduction through FFT analysis by comparing both traditional periodic PWM switching and chaotic PWM switching. The results obtained from the hardware setup shows significant reduction of EMI with Chaotic switching as compared to traditional PWM switching for both boost and buck operation of Luo converter.

The paper presents the design stages of a single-phase Silicon Carbide bidirectional DC-AC converter. This includes the LCL filter design responsible to meet grid connection requirements. A 3kW laboratory prototype of the power converter is built employing a low-cost phase locked loop and its results are presented. The design of the low-cost phase locked loop and its implementation are depicted in some detail.

The article presents an induction generator connected to the power grid using the AC / DC / AC converter and LCL coupling filter. In the converter, both from the generator side and from the power grid side, three-level inverters were used. The algorithm realizing Pulse Width Modulation (PWM) in inverters has been simplified to the maximum. Control of the induction generator was based on the Direct Field Oriented Control (DFOC) method. At the same time, voltage control has been used for this solution. The MPPT algorithm has been extended to include the variable pitch range of the wind turbine blades. The active voltage balancing circuit has been used in the inverter DC voltage circuit. In the control system of the grid converter with an LCL filter, the number of measurements was limited to the measurement of power grid currents and voltages. Synchronization of control from the power grid side is ensured by the use of a PLL loop with the system of preliminary suppression of undesired harmonics (CDSC).

Previous studies generally reckon that the full converter-base wind power generation (FCWG) is a ’decoupled’ power source from the grid, which hardly participates in electromechanical oscillations. However, it is found recently that strong interaction could be induced which might incur severe resonance incidents in electromechanical dynamic timescale. In this paper, the participation of FCWG in electromechanical dynamics is extensively investigated, and particularly, an unusual transition of electromechanical oscillation mode (EOM) is uncovered for the first time. The detailed mathematical models of open-loop and closed-loop power systems are firstly established, and modal analysis is employed to quantify the FCWG participation in electromechanical dynamics, with two new mode identification criteria, i.e., FCWG dynamics correlation ratio (FDCR) and quasi-electromechanical loop correlation ratio (QELCR). On this basis, the impact of different wind penetration levels and controller parameter settings on the participation of FCWG is investigated. It is revealed that if an FOM has a similar oscillation frequency to the system EOMs, there is a high possibility to induce strong interactions between FCWG dynamics and system electromechanical dynamics of the external power systems. In this circumstance, an interesting phenomenon may occur that an EOM may be dominated by FCWG dynamics, and hence is transformed into a quasi-EOM, which actively involves the participation of FCWG quasi-electromechanical state variables.

This research work deals hybrid control system based integrated Cuk converter fed brushless DC motor (BLDCM) for power factor correction. In this work, moth-flame optimization (MFO) and fuzzy logic controller (FLC) has been combined and moth –flame fuzzy logic controller (MFOFLC) has been proposed. Firstly, the BLDC motor modelling is composed with power factor correction (PFC) based integrated Cuk converter and BLDC speed is regulated using variable DC-Link inverter voltage which makes low switching operation with less switched losses. Here, with the use of switched inductor, the task and execution of proposed converter is redesigned. The DBR (diode bridge rectifier) trailed by proposed PFC based integrated Cuk converter operates in discontinuous inductor conduction mode(DICM) for achievement of better power factor.MFO is exhibited for gathering of dataset from the input voltage signal. At that point separated datasets is send to FLC to improve the updating function and minimization of torque ripple. However, our main objective is to assess adequacy of proposed method, the power factor is broke down. The execution of the proposed control methodology is executed in MATLAB/Simulink working platform and the display is assessed with the existing techniques.

This research work explains the practical realization of hybrid solar wind based standalone power system with maximum power point tracker (MPPT) to produce electrical power in rural places (residential applications). The solar inspired Ant Colony Optimization (ACO) based MPPT algorithm is employed for the purpose of fast and accurate tracking power from solar and wind system. Fuzzy Logic Control (FLC) inverter controlling strategy is adopted in this presented work compared to classical PI control. Moreover, single Cuk converter is operated as impedance power adapter to execute MPPT functioning. Satisfactory practical results have been realized using dSPACE (DS1104) platform that justify the superiority of proposed algorithms designed under various operating situations.

To reduce the redundant counting of TDC in high-speed applications and thus reduce power consumption, a TDC architecture is proposed to quantify the difference between two adjacent rows of pixel signals. This structure can remove the identical part between two rows of pixel signals by adjusting the start and stop signal of the TDC, which will reduce the number of flipping of D flip-flops in the TDC. In the 110nm CMOS process, simulation results show that this design achieves an effective number of bits (ENOB) of 4.72 bits and a Figure of Merit (FoM) of 104.7 fJ/step - 162.3 fJ/step with a power consumption ranging from 60 µW to 93 µW. Compared with traditional counting methods, the proposed TDC can reduce counting power consumption by 30%.

The article presents a method of generating Key Performance Indicators related to electric motor energy efficiency on the basis of Big Data gathered and processed in frequency converter. The authors proved that using the proposed solution it is possible to specify the relation between the control mode of an electric drive and the control quality-energy consumption ratio in the start-up phase as well as in the steady operation with various mechanical loads. The tests were carried out on a stand equipped with two electric motors (one driving, the other used to apply the load by adjusting the parameters of the built-in brake). The measurements were made in two load cases, for motor control modes available in industrially applied frequency converters (scalar V/f, vector Voltage Flux Control without encoder, vector Voltage Flux Control with encoder, vector Current Flux Control and Vector Current Flux Control with torque control). During the experiments values of current intensities (active and output), the actual frequency value, IxT utilization factor, relative torque and the current rotational speed were measured and processed. Based on the data the level of the energy efficiency was determined for various control modes.

Power generation systems based on renewable energy sources are finding ever-widening applications and many researchers work on this problem. Many papers address the problem of transformerless structures, but few of them are aimed at conducting research on structures with multilevel converter topologies. In this paper a grid-tied transformerless PV-generation system based on a multilevel converter is discussed. There are common-mode leakage currents which act as a parasitic factor. It is also known that common-mode voltage is the main cause of the common-mode leakage current in grid-tied PV-generation systems. This paper considers the space vector pulse-width modulation (PWM) technique which is used to suppress or reduce common-mode leakage current. The proposed engineering solutions for a generation system based on the multilevel converter controlled with a pulse-width modulation technique are verified by experiment.

Wave energy converter (WEC) arrays deployed in coastal regions may create physical disturbances potentially resulting in environmental stresses. Presently, limited information is available on the nature of these physical disturbance or the resultant effects. A quantitative Spatial Environmental Assessment Tool (SEAT) for evaluating potential effects of wave energy converter (WEC) arrays on nearshore hydrodynamics and sediment transport is presented for the central Oregon coast (USA) through coupled numerical model simulations of an array of WECs. Derived climatological wave conditions were used as inputs to the model to allow for the calculation of risk metrics associated with various hydrodynamic and sediment transport variables such as maximum shear stress, bottom velocity, and change in bed elevation. The risk maps provided simple, quantitative, and spatially-resolved means of evaluating physical changes in the vicinity of a hypothetical WEC array in response to varying wave conditions. Near-field risk of sediment mobility was determined to be moderate in the lee of the densely spaced array, where the potential for increased sediment deposition could result in benthic habitat alteration. Modifications to the nearshore sediment deposition and erosion patterns were observed near headlands and topographic features, which could have implications for littoral sediment transport. The results illustrate the benefits of a risk evaluation tool for facilitating coastal resource management at early market marine renewable energy sites.

The main objective of the paper is to provide a thorough analysis of currently used modulation control schemes for single phase bidirectional dual active bridge DC/DC converter. In this article, it will be shown that single phase shift, extended phase shift and Dual phase shift modulation schemes are special cases of triple phase shift (TPS) modulation scheme. The article aims to highlight six TPS switching modes and their complements with the operational constraints. Unlike previous studies that regarded TPS as a complex scheme, this paper simplifies the analysis of each mode and aims to standardize the understanding of TPS modulation in DAB converters. Power equations, range of power transferred and zero voltage switching (ZVS) are derived for all the modes under TPS without assuming fundamental component analysis. Additionally, a generic optimization algorithm is developed to show the advantages of TPS modulation and thus, detailed analysis presented in this paper provides valuable insights for single phase DAB converter designers in identifying a wide range of optimization algorithms to achieve higher efficiency under TPS modulation. This analysis contributes to the advancement of bidirectional DAB converter technology and facilitates its application in various power electronic systems.

This paper presents an optimal design for the inner current control loop of the continuous current conduction mode (CCM) power factor correction (PFC) stage, which it can be used as the front stage of the two stages alternating current-direct current (AC-DC) telecom power supply. Conventional single-phase CCM-PFC boost converter usually implemented with using of the proportional-integral (PI) controllers in both of the voltage and current control loops, to regulate the output DC voltage to the specified value, moreover to maintains the input current follows the input voltage which offers converter with high power factor (P.F) and low current total harmonic distortion (THD). However, due to the slow dynamic response of the PI controller at the zero-crossing point of the input supply current, input current can’t fully follow the input voltage which leads to high THD. Digitally controlled PFC converter with an optimal design of the inner current control loop using doubly control loops IP controller to reduce the THD and to offer input current with unity P.F was performed in this paper. Furthermore, for the economic design of the digitally control PFC converter, two isolated AC and DC voltage sensors are proposed and designed for the interfacing with the microcontroller unit (MCU). PSIM software was used to test the converter performance with using the proposed designed current controllers and isolated voltage sensors. High power density digitally controlled telecom PFC stage with P.F of about 99.93%, full load efficiency of about 98.70% and THD less 5.50% is achieved in this work.

In this paper, the active front-end (AFE) converter topology for the total harmonic distortion (THD) reduction in a wind energy system (WES) is used. A higher THD results in serious pulsations in the wind turbine (WT) output power and in several power losses at the WES. The AFE converter topology improves capability, efficiency and reliability in the energy conversion devices; by modifying a conventional back-to-back converter, from using a single voltage source converter (VSC) to use pVSC connected in parallel the AFE converter is generated. The THD reduction is done by applying a different phase shift angle at the carrier of digital sinusoidal pulse width modulation (DSPWM) switching signals of each VSC. To verify the functionality of the proposed methodology, the WES simulation in Matlab-Simulink® is analyzed, and the experimental laboratory tests using the concept of rapid control prototyping and the real-time simulator Opal-RT® Technologies is achieved. The obtained results show a type-4 WT with total output power of 6MVA, generating a THD reduction up to 5.5 times at the WES.

The development trends of the modern world of power electronics dictate the requirements for the use of AC voltage converters as soft starters for induction motors. A direct connection of the motors to the mains voltage negatively affects both the motor itself and the mains system as a whole due to high starting currents values, which entail, as a rule, more frequent accidents and shorter the drive system service life. The paper presents a study of the control system of a multi-zone AC voltage regulator. The use of capacitive voltage dividers will also compensate for the consumed reactive power. The article analyzes the features of modern soft starters, describes the circuit design, presents a mathematical calculation by the method of algebraization of differential equations, a performed simulation modeling in Matlab/Simulink, and also an assembled experimental stand for further research. Particular attention is paid to the definition of the multizonality concept of the proposed converter and the analysis of the control method. The developed algorithm of the double-loop automatic control system will minimize the influence of induction motors on the mains voltage, and thus improve electromagnetic compatibility.

This article presents a proposed system that enables energy transfer from the dc grid to a single-phase onboard grid, operating at an hi frequency. In addition to the energy transfer function, it additionally enables compensation of reactive power in the ac grid when the converter operates at less than rated power. To operate in compensator mode, it is necessary to decouple the current from the grid into active and reactive components and control them independently. To achieve good dynamics, synchronizers that operate in the dq system are used. In the case of a single-phase grid, it requires such a synchronizer to generate virtual quadrature signals. The used systems based on second-order generalized integrator are good, but to improve dynamics in the work a quadrature generator based on trigonometric calculations was proposed. The developed system was implemented in a proportional resonant current control system. Tests performed in steady state and in dynamic states related to typical grid disturbances showed better dynamic properties than the standard integrator-based system.Keywords: power transfer; compensator; P+R controller

Glycosidic linkage analysis was conducted on the unfractionated polysaccharides in the alcohol-insoluble residues (AIRs) prepared from six red seaweeds (Gracilariopsis sp., Prionitis sp., Mastocarpus papillatus, Callophyllis sp., Mazzaella splendens, and Palmaria palmata) using GC-MS/FID analysis of partially methylated alditol acetates (PMAAs). The cell walls of P. palmata primarily contained mixed-linkage xylans and small amounts of sulfated galactans and cellulose. In contrast, the unfractionated polysaccharides of the other five species were rich in galactans displaying diverse 3,6-anhydro-galactose and galactose linkages with varied sulfation patterns. Different levels of cellulose were also observed. This glycosidic linkage method offers advantages for cellulose analysis over traditional monosaccharide analysis that is known for underrepresenting glucose in crystalline cellulose. Relative linkage compositions calculated from GC-MS and GC-FID measurements showed that anhydro sugar linkages generated more response in the latter detection method. This improved linkage workflow presents a useful tool for studying polysaccharide structural variations across red seaweed species. Furthermore, for the first time, relative linkage compositions from GC-MS and GC-FID measurements, along with normalized FID and total ion current (TIC) chromatograms without peak assignments, were analyzed using principal component analysis (PCA) as a proof-of-concept demonstration of the technique's potential to differentiate various red seaweed species.