We aimed to investigate the relationship between membrane material and development of membrane fouling in a membrane bioreactor (MBR) using membranes with different pore sizes and hydrophilicities. Batch filtration tests were performed using submerged single hollow fiber membrane ultrafiltration (UF) modules with different polymeric membrane materials including cellulose acetate (CA), polyethersulfone (PES), and polyvinylidene fluoride (PVDF) with activated sludge taken from a municipal wastewater treatment plant. The three UF hollow fiber membranes were prepared by a non-solvent-induced phase separation method and had similar water permeabilities and pore sizes. The results revealed that transmembrane pressure (TMP) increased more sharply for the hydrophobic PVDF membrane than for the hydrophilic CA membrane in batch filtration tests, even when membranes with similar permeabilities and pore sizes were used. PVDF hollow fiber membranes with smaller pores had greater fouling propensity than those with larger pores. In contrast, CA hollow fiber membranes showed good mitigation of membrane fouling regardless of pore size. The results obtained in this study suggest that the surface hydrophilicity and pore size of UF membranes clearly affect the fouling properties in MBR operation when using activated sludge.

Production of wastewater related to the oil and gas industries is increasing over the years. The compounds found in industrial wastewater typically show high toxicity, and in this way, they have become a primary environmental concern. Several techniques have been applied in industrial effluents remediation. In spite of the efforts, these techniques are yet ineffective to treat oily wastewater before it can be discharged safely to the environment. Membrane technology is an attractive approach to treat oily wastewater. This is dedicated to the immobilisation of TiO2 nanoparticles on poly (vinylidene fluoride–trifluoro ethylene) (PVDF-TrFE) porous matrix by solvent casting. Membranes with interconnected pores with an average diameter of 60 micrometres and the contact angle of 97°, decorated with TiO2 nanoparticles, are obtained. The degradation of oily wastewater demonstrated the remarkable photocatalytic efficiency of the nanocomposite membranes: under sunlight irradiation for 7 hours, colourless water was obtained. These results show the suitability of TiO2/P(VDF–TrFE) nanocomposite for photocatalytic applications for oily wastewater remediation.

The new hybrid composite materials for PEM fuel cell were synthesized by UV-polymerization of acrylic monomers (acrylonitrile (AN), acrylic acid (AA), ethylene glycol dimethacrylate (EGDMA)) and sulfo aromatic monomer – sodium styrene sulfonate (SSS), and tetraethoxysilane/3-methacryloxypropyltrimethoxysilane (TEOS/MAPTMS)-based sol-gel system. By means of X-ray spectroscopy fractal structure of the obtained materials was characterized. Proton conductivity and viscoelastic properties of the materials were investigated depending on the content of inorganic component in nanocomposites. On the basis of impedance studies, an equivalent scheme is proposed that successfully describes the proton conductivity in the synthesized composite electrolyte membranes.

Quasi-solid composited electrolytes were produced by LiFSI initiated polymerized poly-(Dioxolane) (PDOL) with garnet-LLZO (Li7La2Zr3O12) nanofibers and used in lithium-metal batteries. Linear sweep voltammetry shows that the initial oxidation voltage of 4.6 V for Gel-10% (G10, 10% wt. LLZO in PDOL) vs Li/Li+. EIS test of stainless steel// stainless steel symmetric cells for Gel-1% (G1), Gel-5% (G5) and Gel-10% (G10) show ion conductivity (5*10-5 S/cm). Li/G10/Li symmetric cells have stable stripping-plating cycling performance over 1300 hours continuously with the current density of 0.1 mA/cm2 at 25 oC, indicating a good interface contact and stable lithium-ion transport pathway through the composite electrolytes. LFP/G10/Li batteries have stable charge-discharge plateau, low polarization voltage of 0.07-volt, energy efficiency of 95% and coulombic efficiency of ~99% at current density of 26.3 mA/g at 25 oC for over 100 cycles.

The processability of conductive polymers such as polyaniline (PANI) still poses a challenge due to their properties. The use of stabilizers, compatible and able to interact with PANI, to obtain dispersible and stable colloids is described in this work. To this aim, potato starch has been used as a steric stabilizer for the preparation of polyaniline (emeraldine salt, ES)/starch biocomposites, by exploiting oxidative polymerization of aniline in aqueous solutions containing different ratios of aniline and starch (% w/w). The polyaniline/starch biocomposites were subjected to structural and spectroscopic analyses, thermal analysis, morphological analysis and electrochemical analysis. The samples were then tested for their dispersibility/solubility in various organic solvents. The results showed the formation of PANI/starch biocomposites with an overall smaller size than starch particles, with improved aqueous dispersion and solubility in organic solvents. Although X-ray diffraction and differential scanning calorimetry analyses indicated a loss of crystallinity in the biocomposites, the cyclic voltammetry tests showed that all PANI ES/starch biocomposites display improved redox exchange properties.

Nowadays asymmetric thin film composite (TFC) polymeric hollow fiber (HF) membranes are extensively used in industrial gas/vapor separations, water treatment etc. There are numerous advantages to use hollow fibers such as: low energy requirements, simplicity of operation, and high specificity. In the present article we discuss the progress made during the past decade in the preparation of the HF substrate and preparation/modification of the thin selective layer. Their applications in water treatment, dehydration of alcohols via pervaporation and gas/vapor separation are also demonstrated.

Corneal diseases are the third leading cause of blindness worldwide. There are numerous causes of corneal blindness, and the common treatment for this condition often involves corneal tissue transplantation, such as Descemet's Membrane Endothelial Keratoplasty (DMEK). DMEK has been established as the preferred surgical technique for the treatment of corneal endothelial disorders. The success of DMEK depends largely on the quality of the donor endothelial cells and the trans-plantation procedure. However, the scarcity of suitable donor tissue and the sensitivity of endo-thelial cells pose a major challenge. In recent years, tissue engineering has attracted attention as potential solutions to these problems. This review offers an outline of the current landscape of DMEK in the context of bioengineering, exploring various methodologies, advancements, and fu-ture prospects.

Previous reviews by the authors [1, 2] indicate the continuing development and improvement of thermal protective systems through the introduction of polymer nanocomposites into polymer matrix composites. These materials perform as thermal protective systems for a variety of aerospace applications, such as thermal protection systems (TPS), solid rocket motors (SRM) nozzles, internal insulation of SRM, leading edges of hypersonic vehicles, and missile launch structures. A summary of the most recent, global technical research is presented. Polymeric resin systems continue to emphasize phenolic resins and other materials. New high-temperature organic resins based on phthalonitrile (PN), and polysiloxane are described and extend the increased temperature range of resin matrix systems.

Extracorporeal membrane oxygenation (ECMO) is increasingly used in intensive care units; however, ECMO can modify drug pharmacokinetics (PK), leading to underexposure and associated treatment failure. The aim of the present study was to determine the effect of ECMO on the PK of dexmedetomidine (DEX). In vivo rat models were developed, both of which involved a bolus injection of DEX and concentration monitoring. In the in vivo model experiment, rats which underwent ECMO were compared with a control group. PK analysis of in vivo data (noncompartmental analysis and nonlinear mixed-effects modelling) was carried out to determine the effect of ECMO. In vivo PK exploration showed that ECMO induced a decrease in DEX clearance. Because the effect of ECMO on the PK of DEX is not clinically significant, normal DEX dosing for critically ill patients should be effective for patients undergoing ECMO.

Hydrogels can be considered as mimics of extracellular matrix (ECM).Cytoskeleton through integrins is connected with ECM and cytoskeleton tension depends on ECM stiffness.A number of age-related diseases depend on cellular processes related with cytoskeleton function.Some examples of cancer initiation and progression and heart disease in relationship with ECM stiffness has been analysed.Incorporation of rigid particles in ECM can increase ECM stifness and to promote formation of internal residual stresses. Water migration, changes of water binding energy to biomactomolecules, changes of the state of water from tightly bound water to free and loosely bound water changes stiffness of ECM. Risks related with rigid particles incorporation into ECM have been also iscussed.

The results of the investigation showed that second-order kinetics govern the adsorption process, and the corresponding rate constants were found. To evaluate the parameters related to the adsorption process, the adsorption equilibrium was examined using a variety of mathematical models, such as the Langmuir, Freundlich, Temkin, and Dubinin-Radushkevich isotherm models. The Langmuir isotherm was found to be the best appropriate among all models for describing the adsorption of Cu2+ and Ni2+ ions using bio-nanocomposite beads. The positive values of ΔH° indicate that the adsorption is physical and endothermic, in agreement with experimental results. The negative value of ∆G° shows that the adsorption process is spontaneous. Positive ΔS° values indicate increased randomness at the solid/liquid interface, during adsorption of Cu2+ and Ni2+ cations onto the engineered bio-nanocomposite. The maximum adsorbed amounts of metal ions by the bio-nanocomposite used were 370.37 mg/g for Ni2+ and 454.54 mg/g for Cu2+ from single system. For the binary system, according to the Langmuir isotherm, the maximum adsorbed amounts of Ni2+ and Cu2+ were 357.14 mg/g and 370,37 mg/g, respectively. There is proof that Alginate-Moroccan clay bio-nanocomposites can serve as a different, less expensive source of sorbents for the removal of metal ions from single and binary systems.

This study introduces a novel nanocomposite coating composed of PANI/CeO2 nanocomposite films, aimed at addressing corrosion protection needs. Analysis through FTIR spectra and XRD patterns confirms the successful formation of the nanocomposite films. Notably, the PANI/CeO2 nanocomposite films exhibit a hydrophilic nature. The bandgap energy of the PANI composite film measures at 3.74 eV, while the introduction of CeO2 NPs into the PANI matrix reduces the bandgap energy to 3.67 eV. Furthermore, the electrical conductivity of the PANI composite film is observed to be 0.40 S.cm-1, with the incorporation of CeO2 NPs leading to an increase in electrical conductivity to 1.07 S.cm-1. To evaluate its efficacy, electrochemical measurements were conducted to assess the corrosion protection performance. Results indicate a high protection efficiency of 92.25% for the PANI/CeO2 nanocomposite film.

Infectious diabetic wounds can result in severe injuries or even death. Biocompatible wound dressings offer one of the best ways to treat these wounds, but creating a dressing with suitable hydrophilicity and biodegradation rate can be challenging. To address this issue, we used the electrospinning method to create a wound dressing composed of poly(glycerol sebacate) (PGS) and gelatin (Gel). We dissolved the PGS and Gel in acetic acid (75 v/v%) and added EDC/NHS solution as a crosslinking agent. Our measurements revealed that the scaffolds' fiber diameter ranged from 180.2 to 370.6 nm, and all the scaffolds had porosity percentages above 70%, making them suitable for wound healing applications. Additionally, we observed a significant decrease (p < 0.05) in the contact angle from 110.8° ± 4.3° for PGS to 54.9° ± 2.1° for PGS/Gel scaffolds, indicating an improvement in hydrophilicity of the blend scaffold. Furthermore, our cell viability evaluations demonstrated a significant increase (p < 0.05) in cultured cell growth and proliferation on the scaffolds during the culture time. Our findings suggest that the PGS/Gel scaffold has potential for wound healing applications.

Carbon nanodots (CNDs) have garnered significant attention as viable drug delivery vehicles in recent years, especially in the field of phytomedicine. Although there is much promise for therapeutic applications with phytomedicine, its effectiveness is frequently restricted by its low solubility, stability, and bioavailability. This paper offers a thorough synopsis of the developing field of phytomedicine drug delivery based on CND. It explores CND synthesis processes, surface functionalization strategies, and structural and optical characteristics. Additionally, the advantages and difficulties of phytomedicine are examined, with a focus on the contribution of drug delivery methods to the increased effectiveness of phytomedicine. The applications of CNDs in drug delivery are also included in the review, along with the mechanisms that underlie their improved drug delivery capabilities. Additionally, it looks at controlled release methods, stability augmentation, and phytomedicine loading tactics onto CNDs. The potential of polymeric carbon nanodots in drug delivery is also covered, along with difficulties and prospective directions going forward, such as resolving toxicity and biocompatibility issues. In summary, the present review highlights the encouraging contribution of CNDs to the field of drug delivery, specifically in enhancing the potential of phytomedicine for therapeutic purposes.

Background/Objectives: The aim of this study was to investigate feasibility and safety of neuromuscular electrical stimulation (NMES) in patients on extracorporeal membrane oxygenation (ECMO) and assess thoroughly any potential adverse events. Methods: We conducted a safety and feasibility study including 16 ICU patients on ECMO support who were admitted to the cardiac surgery ICU from January 2022 to December 2023. Patients underwent a 45-minute NMES session, still on ECMO support, that included a warm up phase of 5 minutes, a main phase of 35 minutes and a recovery phase of 5 minutes. NMES was implemented on vastus lateralis, vastus medialis, gastrocnemius and peroneus longus muscle of both lower extremities. Two stimulators delivered biphasic, symmetric impulses of 75 Hz, with 400 μsec pulse duration, 5 sec on (1,6 sec ramp up and 0,8 sec ramp down) and 21 sec off. The intensity levels aimed to cause visible contractions and be well tolerated. Primary outcomes of the study were feasibility and safety, evaluated by whether the NMES sessions were successfully achieved, and by any adverse events and complications. Secondary outcomes included indices of rhabdomyolysis from biochemical blood test, 24 hours after the application of NMES. Results: All patients successfully completed their 45-minute NMES session, without presenting hemodynamic deterioration, adverse events or signs of rhabdomyolysis. The majority of patients achieved type 4 and 5 quality of muscle contraction. Conclusions: NMES is a safe and feasible exercise methodology in patients supported with ECMO.

In this work, zinc oxide (ZnO)/ granular activated carbon (GAC) composites at different ZnO concentration (0.25M-ZnO@GAC, 0.5M-ZnO@GAC, and 0.75M-ZnO@GAC) were prepared by an in-situ hydrothermal method and demonstrated synergistic photocatalytic degradation and ad-sorption of Rhodamine B (RhB). The thermal stability, morphological structure, elemental com-position, crystallographic structure, and textural properties of developed catalysts were charac-terized by thermal gravimetric analysis (TGA/DTG), scanning electron microscopy equipped with energy dispersive-x-ray (SEM-EDS), x-ray diffraction (XRD), and Brunauer–Emmett–Teller (BET) analysis. Successful loading of ZnO onto GAC was confirmed by SEM-EDS and XRD analysis. The BET surface areas of GAC, 0.25M-ZnO@GAC, 0.5M-ZnO@GAC, and 0.75M-ZnO@GAC were 474 m2/g, 450 m2/g, 453 m2/g, and 421 m2/g, respectively. The decrease in GAC could be attributed to the successful loading of ZnO on the GAC surface. Notably, 0.5M-ZnO@GAC exhibited the best photocatalytic degradation efficiency of 82% and 97% under UV-A and UV-C light over 120 min, attributed to improved crystallinity and visible light absorption. The photocatalytic degradation parameters revealed that lowering the RhB concentration, raising the catalyst dosage and pH be-yond the point of zero charge (PZC) would favor the RhB degradation. Photocatalytic reusability was demonstrated over 5 cycles. Scavenger tests revealed that the hydroxyl radicals (•OH), su-peroxide radicals (O2−•), and photoinduced hole (h+) radicals play a major role during the RhB degradation process. Based on the TOC results, the RhB mineralization efficiency of 79.1% was achieved by 0.5M-ZnO@GAC. Additionally, GAC exhibited a strong adsorptive performance towards RhB with adsorption capacity and RhB removal of 487.1 mg/g and 99.5% achieved within 90 min equilibrium time. The adsorption characteristics were best described by pseu-do-second-order kinetics, suggesting chemical adsorption. This research offers a new strategy for the development of effective photocatalyst materials with potential for wider wastewater treat-ment applications.

The per capita availability of freshwater resources on a global scale is gradually decreasing due to population growth, rapid urbanization, industrialization, and modern lifestyles. In this situation, wastewater management becomes a major concern. Conventional treatment processes used to treat wastewater discharges are not adequate for the advanced removal of pollutants, especially refractory organic pollutants, which are mainly organic compounds that are not easily biodegradable in the environment. The use of photocatalytic membrane reactors (PMRs) for tertiary wastewater treatment has attracted much interest in recent periods, and various configurations have been investigated. The performance of a PMR using an iron doped titanium photo catalyst and Polysulfone-based polymeric membrane for municipal wastewater treatment was evaluated under natural and simulated solar light. Obtained results proved that solar driven PMRs can remove organic loading (COD) with high efficiencies and may represent a suitable alternative for the tertiary treatment step of municipal wastewater.

As marine traffic is contributing to pollution and mostly have predictable route with repetitive load profiles, to reduce their impact on environment, hybrid system with proton exchange membrane fuel cells (PEMFC-s) and battery pack, is promising replacement. For this purpose, the numerical model of repowered existing vessel that have two diesel engines with 300 kWe is developed. The goal of this paper is to develop numerical model which analyzes and determine equivalent hybrid ship propulsion system for known traveling route. The developed numerical model consists of an interconnected system with PEMFC stack and battery pack as power sources. Numerical model is developed and optimized to meet minimal required power demand for successful route demand, which has variable loads and daily sails six-time same voyage- in total 54 nautical miles. The results have shown that equivalent hybrid power system consists of 300 kWe PEMFC stack and battery pack with 424 kWh battery and state of charge varying between 20 and 87%. To power this new hybrid power system, hydrogen tank of 7200 l holding 284.7 kg at pressure of 700 bar is needed, compared to previous system that spend 1524 kg of diesel and generate 4886 kg of CO2.

Artificial membrane systems can serve as models to investigate molecular mechanisms of different cellular processes, including transport, pore formation, and viral fusion. However, the current simulacrums such as SUVs, GUVs, and the supported lipid bilayers suffer from issues, namely high curvature, heterogeneity, and surface artefacts, respectively. Freestanding membranes provide a facile solution to these issues, but current systems developed by various groups use silicon or aluminium oxide wafers for fabrication that involves access to a dedicated nanolithography facility and high cost while conferring poor membrane stability. Here, we report the development, characterization and applications of an easy-to-fabricate suspended lipid bilayer (SULB) membrane platform leveraging commercial track-etched porous filters (PCTE) with defined microwell size. Our SULB system offers a platform to study the lipid composition-dependent structural and functional properties of membranes with exceptional stability in a high throughput fashion. With dye entrapped in PCTE microwells by SULB, we show that sphingomyelin significantly augments the activity of pore-forming toxin, Cytolysin A (ClyA) and the pore formation induces lipid exchange between the bilayer leaflets. Further, we demonstrate high efficiency and rapid kinetics of membrane fusion by dengue virus in our SULB platform. Our suspended bilayer membrane mimetic offers a novel platform to investigate a large class of biomembrane interactions and processes.

Dye/salt separation has gained increasing attention in recent years, prompting the quest for cost-effective and environmentally-friendly raw materials for synthesis high performance nanofiltration (NF) membrane for effective dye/salt separation. Herein, a high-performance loose structured NF membrane was fabricated by via a simple vacuum filtration method using a green nanomaterial, 2,2,6,6-tetramethylpiperidine-1-oxide radical (TEMPO)-oxidized cellulose nanofiber (TOCNF), by sequentially filtrating larger-size and finer-size TOCNFs on a microporous substrate, followed by cross-linked with trimesoyl chloride. The resultant TCM membrane possesses a separating layer composed entirely of pure TOCNF, eliminating the need for other polymer or nanomaterials additives. TCM membranes exhibits high performance and effective dye/salt selectivity. Scanning Electron Microscope (SEM) analysis shows that the TCM membrane with Fine-TOCNF layer has a tight layered structure. Further characterizations via Fourier transform infrared spectroscopy (FTIR) and X-ray diffraction (XRD) confirm the presence of functional groups and chemical bonds of the crosslinked membrane. Notably, the optimized TCM-5 membrane exhibits a rejection rate of over 99% for various dyes (Congo red, orange yellow) and 14.2% for NaCl, showcasing a potential candidate for efficient dye wastewater treatment.

Mechanochemical technology is developing rapidly, judging by the scientific information in both basic and applied studies. However, many issues and points of view remain to be discussed. This review presents some new key issues for the optimization of mechanochemical processes in theoretical and practical aspects. Emphasis is placed on powder technology aspects, which are not always discussed compared to functional or microscopic viewpoints. The transfer of chemical species across the interparticle interface between organic and inorganic species during the mechanosynthesis of nanocomposite oxides offers many new possibilities, which are discussed here in detail. Since all material transport is preceded by charge transfer, its driving force has been searched for using terminology beyond the well-established electrochemical ones. The role of organic compounds during the whole process is emphasized, regardless of their survival in the final product. The similarity with the pharmaceutical phenomena is pointed out, although its mentality is very different from that of the synthesis of nanocomposites. Not only for the rational amorphization of the active pharmaceutical ingredient, but also for the stabilization of molecular dispersion states with the participation of excipients are discussed. The effects of liquids, either added or formed by mechanochemical auto-liquefaction, are presented with reference to the comparison between wet and dry grinding. Finally, mechanisms of apparent stabilization of mechanically activated states of products are elucidated to investigate the practical applicability of mechanochemically synthesized products

We address Multi-Wall Carbon NanoTubes (MWCNTs) for structural health monitoring in adhesive bonds such as in building structures. MWCNT-loaded composites are employed to sense strain changes under tension load using an AC impedance measurement setup. Different weight percentages of 1, 1.5, 2 and 3 wt.% MWCNT are added to the base epoxy resin using different dispersion times, i.e. 5, 10 and 15 minutes. The equivalent parallel resistance of the specimens is measured by applying an alternating voltage at different frequencies. To determine the mechanical as well as sensory properties, the specimens are subjected to a tensile test with concurrent impedance measurement. Using alternating voltage, a higher sensitivity of the impedance reading can be achieved. Employing these sensors in buildings and combining the readings of a network of such devices can significantly improve the buildings’ safety. Additionally, networks of such sensors can be used to identify necessary maintenance actions and locations.

A hybrid material, consisting of commercially available nitrocellulose (NC) membrane non-covalently modified with amino-polyethylene glycol functionalized reduced graphene oxide (NH2-PEG-rGO) nanoparticles, was successfully synthesized for oligonucleotide extraction. Fourier Transform Infrared Spectroscopy (FTIR) confirmed the modification of the NC membrane, revealing characteristic peaks of both compounds NC and NH2-PEG-rGO. Scanning Electron Microscopy (SEM) exhibited morphological changes in the NC/NH2-PEG-rGO hybrid membrane, marked by the introduction of NH2-PEG-rGO particles, resulting in a distinctly smothered surface compared to the porous surface of the NC control membrane. Wettability assays revealed hydrophobic behavior for the NC/NH2-PEG-rGO hybrid membrane, with a water contact angle exceeding 90°, contrasting with the hydrophilic behavior characterized by a 16.7° contact angle in the NC membrane. The performance of the NC/NH2-PEG-rGO hybrid membrane was evaluated for the extraction of ssDNA with fewer than 50 nucleotides from solutions containing various ionic species (MnCl2, MgCl2, and MnCl2/MgCl2). The NC/NH2-PEG-rGO hybrid membrane exhibited optimal performance when incubated in MgCl2, presenting the highest fluorescence emission at 525 relative fluorescence units (r.f.u.). This corresponds to the extraction of approximately 610 pg (≈13%) of the total oligo-DNA, underscoring the efficacy of the pristine material, which extracts 286 pg (≈6%) of oligo-DNA in complex solutions.

Polymer inclusion membranes (PIMs), which contained cellulose tri-acetate used as a polymer base, a plasticizer in the form of o-NPOE, and meso-tetra methyl tetrakis-[methyl-2-(4-acetlphenoxy)] calix[4]pyrrole (KP) used as a carrier, were prepared and tested for the effective purification of aqueous solutions of methylene blue dye. The scanning electron microscope (SEM), thermogravimetric analysis (TGA), and attenuated total reflection Fourier transform infrared (ATR-FTIR) were used to define the microstructure and surface of PIMs. Experimental results showed that with the increased concentration of methylene blue in an aqueous solution, the removal percentage also increased. Further observation also showed that the flux increased with the rise of the source phase pH values from 3 to 10. The carrier and plasticizer content in the membrane significantly influenced the membrane’s transport properties. The optimal composition of the membrane in per cent by weight was for KP: 74% plasticizer; 18% support; 8% carrier. It was shown that the membrane with optimal composition showed good reusability and enabled the easy and spontaneous separation of methylene blue from aqueous solutions.

The literature analysis did not indicate any studies on fluorination tests of carbon nanocomposite coatings doped with transition metals of the nc-MeC/a-C type. This was the motivation for undertaking research in this area. As a model coating to investigate the effect of fluorination in a tetrafluoromethane (CF4) atmosphere, a nano-composite carbon coating doped with chromium nc-CrC/a-C produced by magnetron sputtering from graphite targets and the use of a Pulse-DC type medium frequency power supply was chosen [6]. After deposition of the gradient CrCN adhesive sublayer, fluorination of the main coating was conducted in a reactive mode in an (Ar+CF4) atmosphere at various CF4 contents. It was observed that the presence of CF4 in the atmosphere resulted in a reduced amount of chromium carbides formed in favor of chromium fluorides. So far, this is an observation that seems unnoticed by the carbon coatings researchers. Fluorine was assumed to bond much more readily to carbon than to chromium, due to the stability of tetrafluoromethane (CF4). The opposite seems to be true. The mechanical properties (nano-hardness and Young's modulus) and tribological properties in the 'pin-on-disc' friction pair are presented, along with the analysis of bonds occurring between chromium, carbon, and fluorine (XPS).

Mandibular critical size defect (CSD) due to pathological conditions, trauma, and congenital disease can not heal spontaneously and predominantly filled with fibrous tissue. Therefore, a Guided Bone Regeneration (GBR) combined with bone grafting can be performed. The researchers considered using Demineralized Dentin Material Membrane (DDMM) from bovine dentine as an alternative GBR. This study aimed to determine the amount of fibroblast and collagen density after DDMM and bone graft implantation on CSD. Thirty-six Rattus norvegicus rats were used as samples. Mandibular bone defect 5x5 mm was made, then filled with bone graft and covered with Bovine Pericardium Collagen Membrane (BPCM) in the control group and DDMM in the treatment group. Six samples were sacrificed on 7, 14, and 21 days post-surgical for histology examination. There were no significant differences in the amount of fibroblast and collagen density (p-value > 0,05). The amount of fibroblast is lower and the collagen density is higher in treatment group. DDMM has microporosity to prevent connective tissue ingrowth and dentine tubules to allow growth factors release. DDMM and bone graft implantation can reduce the amount of fibroblasts and increase collagen density of CSD which potentially being used as a CSD alternative treatment for bone regeneration.

Introduction: Atrial fibrillation (AF) is a common cardiac arrhythmia whose prevalence rises with age and is linked to increased morbidity and mortality due to the risk of thromboembolism. Management typically involves anticoagulation and rhythm control, but the treatment of elderly patients with multiple comorbidities requires careful consideration of drug side effects and interactions. Cibenzoline, a Vaughan-Williams class IA antiarrhythmic, is effective against AF but has risks of toxicity, especially in older people and those with renal impairment, due to its renal excretion and prolonged half-life in these populations. Discussion: This paper presents a case of an 80-year-old woman with paroxysmal AF who suffered cardiac arrest due to cibenzoline toxicity despite receiving standard adjusted dosages. The patient's cibenzoline blood concentration was significantly higher than the therapeutic range, leading to cardiotoxicity, which was exacerbated by drug interactions with bisoprolol and edoxaban, both metabolized by the CYP3A4 enzyme. Venoarterial extracorporeal membrane oxygenation (V-A ECMO) and intra-aortic balloon pump (IABP) successfully managed the cardiac arrest. This case emphasizes the unpredictable pharmacokinetics of cibenzoline in elderly patients with renal impairment and the need for vigilant therapeutic drug monitoring to avoid adverse events. Conclusions: Cibenzoline can pose a significant risk of severe toxicity in elderly patients with renal impairment, and drug interactions may potentiate this risk. The paper underscores the importance of careful dose adjustment and monitoring of drug levels in this population. In cases of cibenzoline-induced cardiac arrest, V-A ECMO and IABP are effective treatment modalities. The case study serves as a critical reminder for clinicians to remain vigilant for drug-induced complications and to apply aggressive supportive treatments when necessary.

This article utilized electrodeposition technology to fabricate Zn and Zn-Y₂O₃-Al₂O₃ composite coatings on Q235 steel plates. The composite coatings were obtained by adding Y₂O₃/Al₂O₃ nanoparticles (0, 5, 10, and 15 g/L) to acidic chloride solutions. This study then examined the impact of these nanoparticles on the microstructure, morphology, microhardness, hydrophobicity, and corrosion resistance of the composite coatings. The results indicate that the addition of the nanoparticles increased the nucleation sites on the surface of the coating, thereby refining the grain size and reducing the roughness of the coating surface. When 10g/L of Y₂O₃ and 10g/L of Al₂O₃ nanoparticles were added, the hardness of the composite coating (369 Hv) was 2.49 times higher than that of the pure Zn coating (148 Hv), which was attributed to the dispersion strengthening and grain refinement effects of the nanoparticles. The corrosion resistance of the Zn and Zn-Y₂O₃-Al₂O₃ composite coatings was studied using linear sweep voltammetry and AC impedance spectroscopy. The addition of the nanoparticles improved the corrosion resistance of the composite coating, and the composite coating prepared in an electrolyte containing 10 g/L of Y₂O₃ and 10 g/L of Al₂O₃ nanoparticles exhibited the best corrosion resistance. Meanwhile, the composite coating exhibited good hydrophobicity, with a contact angle of 120.9°, 1.94 times that of the pure Zn coating (62.2°). The Zn-Y₂O₃-Al₂O₃ nanocomposite coating material has significant potential advantages in the field of steel corrosion.

The compatibility of graphene or graphene oxide with its dispersion medium (polymer) plays a critical role in the formation nanocomposite materials with significant property improvements. Environmentally friendly miniemulsion polymerization, which allows a formation of nanoencapsulation in an aqueous phase and high molecular weight polymer/composite production is one promising method. In this study, we screened a series of amphiphilic modifiers and found that the quaternary ammonium (ar-vinyl benzyl) trimethyl ammonium chloride (VBTAC) pending carbon double bonds could effectively modify the graphene oxide (GO) to be compatible with the organophilic monomer. After that, free radical miniemulsion polymerization could successfully synthesize stable latex of exfoliated poly (methyl methacrylate) (PMMA)/ GO nanocomposite. The final latex had an extended storage life and a relatively uniform particle size distribution. X-ray powder diffraction (XRD), transmission electron microscopy (TEM), and scanning electron microscopy (SEM) analysis of this latex and its films indicated successful encapsulation of exfoliated nano-dimensional graphene oxide inside a polymer matrix.

Introduction: Among the many factors that may limit effective wound healing in patients with chronic ulcers, bacterial infection and poor cell recruitment are primary causes that contribute to prolonged healing. Thus, a novel strategy that aims to prevent bacterial infection within the wound, while at the same time providing structural scaffolding that promotes endogenous tissue repair, would be of great interest. Here, we developed a thermo-sensitive silver nanoparticle hydrogel composite as an antibacterial nutritional scaffold for the wound that contains all nutrients required for cell growth while preventing bacterial infection with the ability to fill up all the cavities and void areas in wounds regardless of their geometry. Methods: Silver nanoparticles (AgNPs) were synthesized by chemical reduction. After characterization, silver hydrogel nanocomposite was developed by reconstitution of collagen-based hydrogel powder in a nanoparticle suspension of varying AgNPs concentrations (200, 400, and 600 ppm). The antibacterial activity of the formulations was examined in vitro and in vivo in subcutaneous implant infected model. The wound healing efficacy of the hydrogel nanocomposite was also evaluated using a splinted wound model in rats through comparison of clinical wound measurements and histological assessments. Cytocompatibility assay and biochemical analysis of blood at the end of in vivo wound healing study were performed to evaluate the safety of formulations. Results: The synthesized nanoparticles were spherical and stable. While hydrogel alone did not show any bacterial reduction in vitro, the inhibition of bacterial growth was significant in all silver hydrogel nanocomposites compared to controls (p <0.05) and was dose-dependent, with maximum reduction observed in the 600 ppm group (4.56±0.26 LOG CFU/mL, P<0.001). All concentrations of AgNPs hydrogel composites showed significant antibacterial activity in vivo as well (P<0.0001). Treatment of splinted wounds with AgNPs hydrogel composite resulted in faster wound closure and accelerated wound re-epithelialization. The formulations were non-cytotoxic and did not differ significantly in hematological and biochemical factors from the control group in in vivo study. Conclusions: By presenting promising antibacterial and wound healing activity, silver hydrogel nanocomposite offers a safe therapeutic option that can be used as a functional scaffold for an acceleration of wound healing.

New hybrid nanostructured electrodes for supercapacitors made by combination of electrical double layer and faradaic supercapacitors based-nanomaterials within a single hybrid composite has a great potential on expanding the range of use of these devices and increase their electrochemical performance. In this work, we developed several hybrid nanostructured composites with combinations of such types of materials with potential applicability as electrodes in supercapacitors. In particular, these composites were obtained by easy, cost-effective and scalable procedures, and were composed by NiCo2O4 nanocores as the main faradaic-based nanomaterial and either the conductive polymer polyaniline (PANI), multiwall carbon nanotubes (MWCNTs), or reduced graphene oxide (r-GO) as the electrical double layer-based carbonaceous-based nanomaterials in order to enable the combination of both type of energy storage processes within a single nanostructured device. These constructions allowed us to obtain specific capacitance as large as 1760 F/g, 900 F/g and 734 F/g at a current density of 1 A/g for NiCo2O4/PANI, NiCo2O4/MWCNT, and NiCo2O4/r-GO hybrid nanocomposite electrodes, respectively. Besides, the stability of NiCo2O4/MWCNTs and NiCo2O4/r-GO-based electrodes was outstanding, with capacity losses below 10% after long periods of operation (> 500 cycles).

Biological membranes are fascinating. Santiago Ramón y Cajal, who received the Nobel prize in 1906 together with Camillo Golgi for their work on the nervous system, wrote “[..]in the study of this membrane[..] I felt more profoundly than in any other subject of study the shuddering sensation of the unfathomable mystery of life”[1]. The visualization and conceptualization of these biological objects have profoundly shaped many aspects of modern biology, drawing inspiration from experiments, computer simulations, as well as from the imagination of scientists and artists. The aim of this review is to provide a fresh look on current ideas of biological membrane organization and dynamics by discussing selected examples across fields [1] The full quotation is “I must not conceal the fact that in the study of this membrane I for the first time felt my faith in Darwinism (hypothesis of natural selection) weakened, being amazed and confounded by the supreme constructive ingenuity revealed not only in the retina and in the dioptric apparatus of the vertebrates but even in the meanest insect eye. There, in fine, I felt more profoundly than in any other subject of study the shuddering sensation of the unfathomable mystery of life.” from the autobiography Recollections of My Life.

The most common and taught membrane theory assumes that the membrane behaves as a kind of electrical capacitance that is exposed to an electrical current generated by an ionic flow. If this statement is verifiable, it can be confirmed by the laws of physics, mathematics and in particular electricity. We will demonstrate that this hypothesis is not verified and that it is necessary to modify biophysics according to already established and experimentally verified principles of physics.

Membrane-based sensors (MePSs) exhibit remarkable precision and sensitivity in detecting pressure changes. MePSs are commonly used to monitor catalytic reactions in solution, generating gas products crucial for signal amplification in bioassays. They also allow catalyst quantification by indirectly measuring the pressure generated by the gaseous products. This is particularly interesting to detect enzymes in biofluids associated with disease onset. To enhance the performance of a MePS, various structural factors influence membrane flexibility and response time, ultimately dictating the device's pressure sensitivity. In this study, we fabricated MePSs using polydimethylsiloxane (PDMS) and investigated how structural modifications affect the Young's modulus (E) and residual stress (σ0) of the membranes. These modifications have a direct impact on the sensors' sensitivity to pressure variations, observed as a function of the volume of the chamber (Σ) or of the mechanical properties of the membrane itself (S). MePSs exhibiting the highest sensitivities were then employed to detect catalyst quantities inducing the dismutation of hydrogen peroxide, producing dioxygen as gaseous product. As a result, catalase enzyme was successfully detected using these optimized MePSs, achieving a remarkable sensitivity of (22.7 ± 1.2) µm/nM and a limit of detection (LoD) of 396 pM.

Olivine-like NaFePO4 glasses and nanocomposites are promising materials for cathodes in sodium batteries. Our previous study concerned the influence of high pressure on DC electric conductivity of NaFePO4 glasses. This work presents the results of AC measurements of glasses and nanocomposites from pressure treatment. Depending on the temperature range, the electronic conduction mechanism changed from variable range hopping (between Fe2+/Fe3+centers) to phonon-assisted hopping. For DC electric conductivity the portrayal via the classic Mott’s Variable Range Hopping is limited to low temperatures. Spectra of AC conductivity for glasses and pressure-formed nanocomposites fulfill Jonscher’s scaling law with power exponents ranging from 0.3 to 0.9 depending on temperature and the electron hopping mechanism. Due to the decrease in distance between hopping centers, an increase of AC conductivity around 2-3 orders of magnitude was observed after high pressure-high temperature treatment. Up to 200 K temperature dependencies of AC conductivity follow the pattern suggested by Mott's theory. Above that temperature corresponds to phonon-assisted hopping with activation energies EAC≈0.40 eV (for glass: amorphous solid) and EAC≈0.18 eV (for glass + nanocrystallites nanocomposite). Notable that they are considerably lower than values of EDC for DC conductivity. Results obtained show that high-temperature compressing, just below the glass temperature, significantly leads to a stable decrease in distance between hopping centers related to nanocrystallites in a glassy matrix. Consequently, it leads to an essential rise in electric conductivity and volumetric capacity. AC spectra of electronic conductivity are disturbed by the conduction of Na+ mobile ions, which impacts polaron conductivity and can be a limiting factor for conductivity.

The reproductive health of women is governed by an optimal balance between the host-microbiota interaction. Depletion in the beneficial vaginal microflora caused by depletion of Lactobacillus species and increased proliferation of pathogens results in gynecological infections. Among women of reproductive age, vaginal infections are increasingly prevalent. Attaining therapeutic efficacy using conventional formulations remains a challenge as vaginal fluids quickly remove or dilute the therapeutic formulations. Hydrogels have been widely exploited for targeted delivery of therapeutics directly into the vaginal mucus. With careful choice of polymers (natural, synthetic or semi-synthetic) hydrogels with specific properties such as stimuli-responsiveness, antimicrobial, and muco-adhesiveness can be tailored for higher therapeutic efficacy. In this review, the advnances in hydrogel strategies for the treatment of vaginal infections is presented with emphasis on the types and properties that play a significant role in vaginal drug delivery systems.

Heavy metal ions (HMIs) have acute toxic effects on the health and are dangerous for human ex-istence and the ecosystem. Therefore, its sensitive and selective detection is of great importance. In recent years various nanocomposite materials have been used by researchers for the detection of HMIs by using various modalities of electrochemical techniques. This review article summarizes the recent advances in developing electrochemical sensors based on numerous nanocomposite mate-rials for detecting heavy metal ions. Nanocomposites materials, such as Metal-Organic Framework (MOF), organic conducting polymers (OCP), carbon nanotubes, graphene/reduced graphene oxide, graphitic carbon nitride, metal oxide, chitosan, mxenes, metal nanoparticle-based nanocomposites, etc. have been explored by various researchers to improve the sensing properties of electrochemical sensors. This review emphasized the synthesis and characterization techniques of nanocomposite materials, modalities for HMI detection by electrochemical technique and the electrochemical sensors. Moreover, this review highlights the development of portable biosensors for detecting HMIs in real-world scenarios, such as environmental monitoring, food safety, and clinical diagnosis. This review also demonstrates the importance of electrochemical sensors-based on nanocomposite ma-terials as a reliable, sensitive, and selective tool for detecting HMIs.

Nanocomposite hydrogels offer remarkable potential for applications in bone tissue engineering. They are synthesized through the chemical or physical crosslinking of polymers and nanomaterials, allowing for the enhancement of their behaviour by modifying the properties and compositions of the nanomaterials involved. However, their mechanical properties require further enhancement to meet the demands of bone tissue engineering. Here, we present an approach to improve the mechanical properties of nanocomposite hydrogels by incorporating polymer grafted silica nanoparticles into a double network inspired hydrogel (gSNP Gels). The gSNP Gels were synthesised via a graft polymerization process using a redox initiator. gSNP Gels were formed by grafting 2-acrylamido-2-methylpropanesulfonic acid (AMPS) as the first network gel followed by a sequential second network acrylamide (AAm) onto amine functionalized silica nanoparticles (ASNPs). We utilized glucose oxidase (GOx), to create an oxygen-free atmosphere during polymerization resulting in higher polymer conversion compared to argon degassing. The gSNP Gels showed excellent compressive strengths of 13.9 ± 5.5 MPa, a strain of 69.6 ± 6.4%, and a water content of 63.4% ± 1.8. The synthesis technique demonstrates a promising approach to enhance the mechanical properties of hydrogels, which can have significant implications for bone tissue engineering and other soft tissue applications.

Geopolymers are ecologically-friendly inorganic materials which can be produced at low temperatures from industrial wastes such as fly ash, blast furnace slags or mining residues. Although to date their principal applications have been as alternatives to Portland cement building materials, their properties make them suitable for a number of more advanced applications, including as photocatalytic nanocomposites for removal of hazardous pollutants from waste water or the atmosphere. For this purpose, they can be combined with photocatalytic moieties such as metal oxides with suitable bandgaps to couple with UV or visible radiation, or with carbon nanotubes or graphene. In these composites the geopolymers act as supports for the photoactive components, but geopolymers formed from wastes containing oxides such as Fe2O3 show intrinsic photoactive behaviour. This review discusses the structure and formation chemistry of geopolymers and the principles required for their utilisation as photocatalysts. The literature on existing photocatalytic geopolymers is reviewed, suggesting that these materials have a promising potential as inexpensive, efficient and ecologically-friendly candidates for the remediation of toxic environmental pollutants and would repay further development.

This study presents a new bionanocomposite coating on poly(ethylene terephthalate) (PET) made of pullulan and synthetic mica. Mica nanolayers have a very high aspect ratio (α) at levels much greater than that of conventional exfoliated clay layers (e.g., montmorillonite). A very small amount of mica (0.02 wt%, which is ϕ ≈ 0.00008) in pullulan coatings dramatically improved the oxygen barrier performance of the nanocomposite films under dry conditions, whereas this performance was partly lost as the environmental relative humidity (RH) increased. This outcome was explained in terms of the perturbation of the spatial ordering of mica sheets within the main pullulan phase because of RH fluctuations, as confirmed by modelling of the experimental OTR data according to Cussler’s model. The presence of the synthetic nanobuilding block (NBB) led to a decrease in both static and kinetic coefficients of friction compared with neat PET (≈12% and 23%, respectively) and PET coated with unloaded pullulan (≈ 26% reduction in both coefficients). In spite of the presence of the filler, all of the coating formulations did not significantly impair the overall optical properties of the final material, which exhibited haze values below 3% and transmittance above 85%, with the only exception represented by the formulation with the highest loading of mica (1.5 wt%, which is ϕ ≈ 0.01). These findings revealed, for the first time, the potential of the NBB mica to produce nanocomposite coatings in combination with biopolymers for the generation of new functional features, such as transparent high oxygen barrier materials.

Bacterial structures formed from the outer membrane and the periplasm components carry biomolecules to expel cellular material and interact with other cells. These outer membrane vesicles (OMVs) can encapsulate bioactive content, which gives OMVs a high potential as alternative drug delivery vehicles or as a platform for novel vaccine development. Single-gene mutants of the hypervesiculating strain Escherichia coli JC8031 were engineered to further enhance OMV production based on metabolic network modelling and in silico gene knockout design (ΔpoxB, ΔsgbE, ΔgmhA, and ΔallD). Mutants were experimentally obtained by genome editing using CRISPR-Cas9 and tested for OMVs recovery observing an enhanced OMV production in all of them. Lipidomic analysis through LC-ESI-QTOF-MS was performed for OMVs obtained from each engineered strain and compared to the wild type E. coli JC8031 strain. The lipid profile of OMVs from the wild type E. coli JC8031 did not change significantly when compared to the mutant strains. The obtained results suggest that the vesicle production can be further improved while the obtained vesicles are not altered in their composition, allowing further study for stability and integrity for use in therapeutic settings.

In the last 20 years, an increasing number of studies have been reported on membrane active peptides, which exert their biological activity by interacting with the cell membrane either to disrupt it and lead to cell lysis or to translocate through it to deliver cargos into the cell and reach their target. These peptides are attractive alternatives to currently used pharmaceuticals. Antimicrobial peptides (AMPs) and peptides designed for drug and gene delivery currently in the drug pipeline suggest that these membrane active peptides will soon constitute a significant percentage of the drug market. Here, we focus on two most prominent classes of membrane active peptides; AMPs and cell-penetrating peptides (CPPs). AMPs are a group of membrane active peptides that disrupt the membrane integrity or inhibit the cellular functions of bacteria, virus and fungi. CPPs are another group of membrane active peptides that mainly function as cargo-carriers even though they may also show antimicrobial activity to some extent. Biophysical techniques to understand how they interact with the membrane have shed light on the peptide–membrane interaction at various levels of detail. Structural investigation of membrane active peptides in the presence of the membrane provides important clues on the effect of the membrane environment on peptide conformations. Advances in live imaging techniques have allowed examination of peptide action at a single cell or single molecule level. In addition to these experimental biophysical techniques, molecular dynamics simulations provided clues on the peptide-lipid interactions and dynamics of the cell entry process at atomic detail. In this review, we summarize the recent advances in experimental and computational investigation of membrane active peptides with particular emphasis on two amphipathic membrane active peptides, the AMP melittin and the CPP pVEC.

The generation and maintenance of membrane potential is a fundamental part of Membrane Pump Theory. One of the key points of this hypothesis is based on a natural or facilitated molecular diffusion through several types of ion channels and pumps like the Na/K ATPase. Chemistry, physics and especially electrochemistry, however, bring strong contradictions to this theoretical assumption. By respecting the principles of chemistry and electrostatics, it becomes obvious that this theoretical hypothesis cannot work. The ionic diffusion that would be at the origin of this potential cannot take place. Indeed, the topology and the forces involved definitively exclude the current model, which must absolutely be revised according to the current state of our knowledge and allow an advance in the understanding of the phenomena and open new research perspectives.

The exploitation of lipid membranes in biosensors has provided the ability to reconstitute a considerable part of their functionality to detect trace of food toxicants and environmental pollutants. Nanotechnology enabled sensor miniaturization and extended the range of biological moieties that could be immobilized within a lipid bilayer device. This chapter reviews recent progress in biosensor technologies based on lipid membranes suitable for environmental applications and food quality monitoring. Numerous biosensing applications are presented, putting emphasis on novel systems, new sensing techniques and nanotechnology-based transduction schemes. The range of analytes that can be currently detected include, insecticides, pesticides, herbicides, metals, toxins, antibiotics, microorganisms, hormones, dioxins, etc. Technology limitations and future prospects are discussed, focused on the evaluation/ validation and eventually commercialization of the proposed sensors.

In order to alter and adjust the shape of the membrane, cells harness various mechanisms of curvature generation. Many of these curvature generation mechanisms rely on the interactions between peripheral membrane proteins, integral membrane proteins, and lipids in the bilayer membrane. One of the challenges in modeling these processes is identifying the suitable constitutive relationships that describe the membrane free energy that includes protein distribution and curvature generation capability. Here, we review some of the commonly used continuum elastic membrane models that have been developed for this purpose and discuss their applications. Finally, we address some fundamental challenges that future theoretical methods need to overcome in order to push the boundaries of current model applications.

The exploitation of lipid membranes in biosensors has provided the ability to reconstitute a considerable part of their functionality to detect trace of food toxicants and environmental pollutants. Nanotechnology enabled sensor miniaturization and extended the range of biological moieties that could be immobilized within a lipid bilayer device. This chapter reviews recent progress in biosensor technologies based on lipid membranes suitable for environmental applications and food quality monitoring. Numerous biosensing applications are presented, putting emphasis on novel systems, new sensing techniques and nanotechnology-based transduction schemes. The range of analytes that can be currently detected include, insecticides, pesticides, herbicides, metals, toxins, antibiotics, microorganisms, hormones, dioxins, etc. Technology limitations and future prospects are discussed, focused on the evaluation/ validation and eventually commercialization of the proposed sensors.

To investigate the effect of acidic nanoparticles on proton conductivity, permeability and fuel cell performance, a commercial Nafion® 117 membrane was impregnated with zirconium phosphates (ZrP) and sulfated zirconium (S-ZrO2) nanoparticles. The tensile test, water uptake, methanol crossover, Fourier-transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), Thermal gravimetric analysis (TGA) and Scanning Electron Microscopy (SEM) were used to assess the ca-pacity of nanocomposite membrane to function in a fuel cell. The modified Nafion® membrane obtained the higher water uptake and a lower water content angle than the commercial Nafion® 117 membrane, indicating that it has a greater impact on conductivity. Under strain rates of 40, 30 and 20 mm/min, the nanocomposite membranes demonstrate more stable thermal deterioration and higher mechanical strength, which offers tremendous promise for fuel cell applications. When compared to 0.113 S/cm and 0.013 S/cm, respectively, of commercial Nafion® 117 and Nafion® ZrP membranes, the modified Nafion® membrane with ammonia sulphate acid had the highest proton conductivity of 7.891 S/cm. When tested using a direct single cell methanol fuel cell, it had the highest power density of 183 m. cm-2 which is better than commercial Nafion® 117 and Nafion® ZrP membranes.

In this study, the pristine MgO, MgO/CNT and Ni-MgO/CNT nanocomposites were processed by the impregnation and chemical vapour deposition methods and analyzed for hydrogen evolution (HER) via electrochemical water splitting process. Furthermore, effect of nickel on the deposited carbon was systematically elaborated in this study. The highly conductive carbon nanotubes (CNTs) deposited on the metal surface of the Ni-MgO nanocomposite heterostructure provides the robust stability and superior electrocatalytic activity. The optimized Ni-MgO/CNT nanocomposite exhibited hierarchical helical-shaped carbon nanotubes adorned on the surface of the Ni-MgO flakes, forming a hybrid metal-carbon network structure. The HER catalytic reaction was carried out in 1M alkaline KOH electrolyte, and the optimized Ni-MgO/CNT nanocomposite achieves the low 117 mV overpotential value (ɳ) at the 10 mA cm-2 and needs low 116 mV/dec Tafel value denoted Volmer-Heyrovsky pathway. Also, high electrochemical active surface area (ECSA) value of Ni-MgO/CNT nanocomposite acquires 515 cm2, which is favorable for the generation of abundant electro-active species and the prepared electrocatalyst durability was also performed by chronoamperometry test for prolonged duration of 20 h at 10 mA cm-2 and exhibits the good stability with 72% retention. Hence, obtained results demonstrated that the optimized Ni-MgO/CNT nanocomposite is highly active and cost-effective electrocatalyst towards hydrogen energy production.

Polyvinyl Alcohol (PVA)/ Graphene Quantum Dots (GQDs) polymer nanocomposite films have been prepared, and the relationship between their structural, thermal and nanoscale morphologi-cal properties, and their photoluminescent response, has been investigated. Although according to X-ray Diffraction (XRD), Fourier-Transform Infrared Spectroscopy (FT-IR) and Differential Thermal Analysis (DTA) the incorporation of GQDs does not significantly affect the percentage crystallinity of the PVA matrix, for a range of added GQD concentrations, Atomic Force Micros-copy (AFM) showed the formation of islands with apparent crystalline morphology on the surface of the PVA/GQD films, with GQD presumably acting as a nucleating agent for island growth. The incorporation of GQD also led to the formation of characteristic surface pores with increased stiffness and frictional contrast, according to Ultrasonic Force Microscopy (UFM) and Frictional Force Microscopy (FFM) data. The photoluminescence (PL) spectra of the films were found to de-pend both on the amount of GQD incorporated and on the film morphology. For GQD loads > 1,2wt%, a GQD-related band was observed at ~ 1650 cm-1 in FT-IR, along with an increase in the PL band at lower energy. For a load of ~2wt% GQD, the surface morphology was characterized by extended cluster aggregates with lower stiffness and friction than the surrounding matrix, and the PL signal decreased.

Carbon nanomaterial is widely used in structural health monitoring due to the advantage of sensitivity and good mechanical properties. This study presents a novel approach employing carbon nanocomposite materials (CNM) to characterize deformation and damage evolution in physical modelling. As the primary measurement method, the CNM is used to investigate the deformation characteristics of a 200-400 m thick sandstone bed at a 1 km deep longwall mine. The sandstone unit is identified as an ultra-thick key stratum (UTKS), with its thicknesses varying across different mining panels of the UTKS. The results of CNM monitoring show that the UTKS remains stable even after a consecutive excavation of 900 m in width. This stability impedes the upward propagation of overlying strata failure, leading to minimal surface subsidence. The study demonstrates the huge potential of CNM in the mining area, which can be useful for investigating material damage in physical modelling studies. The findings suggest that the cumulative extraction width in individual mining areas of the mine should be controlled to avoid a sudden collapse of the UTKS, and that special attention should be paid to where the UTKS's thickness changes substantially. The substantial variation in UTKS thickness significantly impacts the pattern of overburden subsidence.

A nonlinear MEMS multimass sensor is investigated. The MEMS design consists of an array of nonlinear microcantilevers clamped to a shuttle mass which, in turn, is attached to a linear spring and a dashpot. The microcantilevers are made of a polymeric hosting matrix reinforced by aligned carbon nanotubes (CNT) with different CNT volume fractions in each cantilever so as to suitably tune the frequency bandwidth of the device. The advantages of a single input-single output (SISO) system are here exploited for the design, actuation and detection principles as in previous literature.

Green electrospun materials are gaining popularity in the quest for a more sustainable environment for human life. Bee pollen (BP) is a valuable apitherapeutic product, which has many beneficial properties such as antioxidant properties and antibacterial activity. Alginate is a natural and low-cost polymer. Both natural materials show good compatibility with human tissues for biomedical applications and have no toxic effect on the environment. In this study, the production of bee pollen loaded sodium alginate (SA) and polyvinyl alcohol (PVA) nanofibrous mat was fabricated by electrospinning technique. The green electrospun composite mats were characterized by scanning electronic microscopy (SEM), Fourier transforms infrared spectroscopy (FTIR), and differential scanning calorimeter (DSC). According to the findings of the study, the toxin-free electrospinning method is suitable for producing green composite material. Because of the useful properties of the bee pollen and the favorable biocompatibility of the alginate fibers, the bee pollen-loaded SA/PVA electrospun mats have the potential for use in a variety of biomedical applications.

In this research, first a binary nanocomposite of magnetic recyclable photocatalyst Fe₃O₄/TiO₂, was synthesized by sol gel technique. Then, in order to enhance the photocatalytic activity of the synthesized nanocomposite, it was deposited by silver nanoparticles for using in degradation of organic pollutants 2, 4-dichlorophenol (2, 4-DCP) under visible light. A range of analytical techniques including XRD, FESEM/EDX, DRS, VSM and N₂ physisorption were employed to reveal the crystal structure, morphology and property of the nanocomposites. We obtained 32% and 55% degradation of 2, 4-DCP under visible light after 180 min irradiation in the presence of Fe₃O₄/TiO₂ and Fe₃O₄/TiO₂/Ag respectively. Thus, the excellent visible light photocatalytic activity of Fe₃O₄/TiO₂/Ag sample can be attributed to the surface plasmon resonance effect of Ag nanoparticles deposited on Fe₃O₄/TiO₂ nanocomposite.

In order to achieve the dual carbon goal and simplify the decarbonization process, a CO2 recovery process of the fire-flooding exhaust was designed. The process adopted the two-stage membrane separation method to recover CO2 and obtain high purity CO2 rich flow, and then through the mixed refrigerant liquefaction and rectification column, food grade liquid CO2 was obtained. HYSYS process simulation shows that for the fire-flooding exhaust with a flow rate of 1000 kg/h and a given composition, the process can achieve a CO2 recovery of 69.02%, total product sales S=2086.8 yuan/h, and specific power consumption of 2.818 kW∙h/kg. On this basis, a hybrid simulation platform of HYSYS & Matlab was established. Taking the specific power consumption of the product as the objective function, sequential quadratic programming (SQP) algorithm was adopted to optimize the process, and the optimized specific power consumption was reduced by 18.8%. Finally, by adjusting N2/CO2 components, the adaptability of the optimization condition was analyzed.

Dysregulation of cartilage homeostasis and the changes in the density and the architecture of the subchondral bone were postulated as a potent mechanically pathological activity contributing to osteoarthritis (OA) pathogenesis. Extracorporeal shockwave therapy (ESWT) is a new, none invasive and effective method in the treatment of animal OA model. In the current study, we demonstrated that shockwave induced the expression of protein-disulfide isomerase-associated 3 (Pdia-3) which is a multifunctional protein hypothesized to be a significant mediator for 1α,25-Dihydroxyvitamin D3 (1α,25(OH)₂D₃) signaling pathway using two-dimensional electrophoresis. Histological analysis and quantitative polymerase chain reaction (qPCR) were verified and observed that the expression of Pdia-3 at 2 weeks was significantly higher than that of any other group at 4 weeks, 8 weeks, and 12 weeks post-shockwave treatment in early OA knee of rat. The other factors of the 1α,25(OH)₂D₃ rapid membrane signaling pathway including extracellular signal-regulated protein kinases 1 (ERK1), osteopontin (OPG), alkaline phosphatase (ALP), and matrix metallopeptidase 13 (MMP13) were measured and significantly increased by qPCR at 2 weeks post-shockwave treatment in early OA knee. Our proteomic data revealed significant Pdia-3 expression in microenvironments of joint tissue that could be actively responded to ESWT, which may potentially regulate biological function of chondrocytes and osteoblasts in the treatment of OA knee.

Adhesive-invasive E. coli have been suggested to be associated with the development of Crohn's disease (CD). It is assumed that they can provoke the onset of the inflammatory process as a result of the invasion of intestinal epithelial cells, and then, due to survival inside macrophages, stimulate chronic inflammation and the development of granuloma. In previous reports, we have shown that passage of the СD isolate ZvL2 on minimal medium M9 supplemented with sodium propionate (PA) as a carbon source stimulates, and with glucose - inhibits the adherent-invasive properties and the ability to survive in macrophages. This effect was reversible and not observed for the laboratory strain K12 MG1655. We were able to compare the isogenic strain AIEС in two phenotypes - virulent (ZvL2-PA) and non-virulent (ZvL2-GLU). We showed that, unlike ZvL2-GLU, the ZvL2-PA activates the production of ROS and cytokines when interacting with neutrophils. The laboratory strain does not cause a similar effect. Differences in neutrophil NADH-oxidase activation and ζ potential for ZvL2-GLU and ZvL2-PA are associated with changes in the abundance of membrane proteins. Using differential 2D electrophoresis and LC-MS, we identified membrane proteins that may be associated with the activation of the virulence properties of the СD isolate ZvL2.

The generation and maintenance of membrane potential is considered a fundamental element of the cellular machinery. They are based on elements of physics and chemistry. Mathematics is used to validate the equations and evaluate the results. However, this computation process can lead to a misunderstanding of the phenomena involved or to the masking of crucial events. It is even possible that the calculation no longer corresponds to the hypothesis considered. Membrane theory is no exception to these trivial considerations, which are essential for normal theory validation.

Membrane potential generation and maintenance are fundamental parts of membrane theory. However, since its inception, theories and assumptions have remained simple, whereas the amount of knowledge available has only grown. Unfortunately, this simplification and reductionism lead to its loss of validity on both microscopic and macroscopic scales. This article shows that assumptions made outside the context of factual reality lead to contradictions that cannot be compared with science. Membrane theory must be thoroughly revised, taking into account all forgotten and unanswered assumptions and questions to conform to facts and science to maintain credibility.

The membrane potential or resting potential of the neuron has been the subject of many studies. Although this theory explains the generation and maintenance of the membrane potential by direct or even facilitated diffusion, there are too many contradictions to doubt that these forces are sufficient or even at work in a process whose initial conditions are of rare complexity. The aim of this article is to show that already in the past, a competing theory has been developed whose hypothesis seems more scientifically sound. To confirm this last theory, Hirohisa Tamagawa carried out an experiment of great simplicity which makes it possible to invalidate the current theory and to question the teaching and the knowledge in Biology and Biophysics.

There are different treatment options in modern dentistry for the replacement of lost dentition. Of these the most upcoming and acceptable treatment option is Dental implants. The common problem usually with immediate implant placement in the anterior region is the post-operative soft tissue contour as a part of the bone modelling during healing. Hurzeler et al in 2010 introduced a new technique called the “socket shield technique”. This technique has been used as an alternative treatment modality for immediate implant placement in the aesthetic zone.This review articles provides a detailed information regarding the clinical concept of Root membrane technique.

The growing global population and limitations in fish catch production have led to a surge in the demand for aquaculture. Contaminants of emerging concern (CEC) are frequently being detected at low levels in surface water. These CECs, which include previously unidentified or unregulated pollutants, pose potential risks to health and the environment, though their impacts are not yet fully understood. Extensive research studies have been proposed and undertaken to address the issue of aquaculture wastewater, aiming to minimize its impact and implement effective treatment methods. This review provides an analysis of various technologies used for treating aquaculture wastewater using advanced oxidation processes (AOPs) focusing on photocatalysis and ozonation. It examines their advantages and disadvantages, as well as their respective treatment efficacies and discusses their potential applications in sustainable aquaculture practices complying with the Sustainable Development Goals of 1,2 and 6 and the Environmental Social and Governance (ESG) framework.

Currently, petroleum-derived plastics are widely used. However, one of its main disadvantages is its low degradation time, which is not beneficial to the environment. Therefore, natural polymers are an alternative to overcome this obstacle. Among the natural polymers, starch can be highlighted. Thus, the objectives of our investigation were to obtain sisal nanofibers using low concentrations of acid solutions to produce and characterize corn starch nanocomposites reinforced with these nanofibers. The films were produced by a casting technique using commercial corn starch and glycerol as plasticizing agents; the nanofibers were obtained using acid hydrolysis. The films were subjected to tensile tests to evaluate their resulting mechanical behaviors. The results of X-ray diffraction and transmission electron microscopy analyses revealed the possibility of obtaining cellulose nanofibers using a sulfuric acid concentration lower than that previously reported in the literature. The nanocomposites reinforced with plant nanofibers showed lower tensile stress and elongation characteristics than the matrices without nanofibers.

Conductive nanocomposites play a significant role in tissue engineering by providing a platform to support cell growth, tissue regeneration, and electrical stimulation. In this present study, a set of electroconductive nanocomposite hydrogels based on gelatin (G), chitosan (CH) and conductive carbon black (CB) was synthesized with the aim to develop novel biomaterials for tissue regeneration application. Incorporation of conductive carbon black (10, 15 and 20 wt %) significantly improved electrical conductivity and enhanced mechanical properties with the increased CB content. We employed an oversimplified unidirectional freezing technique to impart anisotropic morphology with interconnected porous architecture. An investigation into whether any anisotropic morphology affects the mechanical properties of hydrogel was conducted by performing compression and cyclic compression tests in each direction parallel and perpendicular to macroporous channels. Interestingly, nanocomposite with 10 % CB produced both anisotropic morphology and mechanical property, whereas anisotropic pore morphology diminished at higher CB concentration (15 and 20 %) imparting denser texture. Collectively, the nanocomposite hydrogels showed great structural stability as well as good mechanical stability and reversibility. Under repeated compressive cyclic at 50 % deformation, the nanocomposite hydrogels showed preconditioning, characteristic hysteresis, nonlinear elasticity, and toughness. Overall, the collective mechanical behavior resembled the mechanics of soft tissues. Electrical impedance associated to the hydrogels was studied in terms of modulus and phase in dry and wet condition. The electrical properties conducted in wet conditions, which is more physiologically relevant, showed low impedance at high frequencies due to capacitive currents. Overall, impedance of the nanocomposite hydrogels decreased with increased CB concentrations. These gelatin-chitosan–carbon black nanocomposite hydrogels show great promise for use as conducting substrates for the growth of electro-responsive cells in tissue engineering.

We report the synthesis and characterization of Poly Methyl-Meth-Acrylate (PMMA)/Poly vinylalcohol (PVA) polymeric blend doped with different concentrations of Copper oxide (CuO) nanoparticles (NPs). The (PMMA-PVA)/CuO nanocomposite hybrid thin films (wt. % = 0%, 2%, 4%, 8%, and 16%) of CuO NPs are deposited on glass substrates via dip-coating technique. The transmittance (T%), reflectance (R%), the absorption coefficient (α), the optical constants [refractive index (n), extinction coefficient (k)], optical dielectric functions [ɛ',ɛ''] are investigated and interpreted. Tauc, Urbach, Spitzer-Fan, and Drude models are employed to calculate the optical bandgap energy (Eg) and the optoelectronic parameters of the nanocomposite thin films. The refractive index and optical bandgap energy of of (PMMA-PVA) polymeric thin film are found to be (1.5 to 1.85) and 4.101 eV, respectively. Incorporation of specific concentrations of CuO-NPs in (PMMA-PVA) polymeric thin films leads to a noticeable decrease in the optical bandgap energy and to an increase of the refractive index. Moreover, Fourier Transform Infrared Spectroscopy (FTIR) transmittance spectra are measured and analyzed for undoped and doped polymeric thin films to pinpoint the major vibrational modes in the spectral range (500 and 4000 cm-1), as well as, the nature of network bonding in both systems. Thermal stability of thin films is investigated by performing thermogravimetric analysis (TGA). The TGA thermograms confirm that both doped polymeric thin films are thermally stable at temperatures below 110°C which enables them to be attractive for a wide range of optical and optoelectronic applications. Our results indicate that optical, vibrational and thermal properties of both polymeric thin films can be tuned for specific applications by the appropriate corporation of particular concentrations of CuO-NPs.

Endothelial cells are the crucial inner lining of blood vessels, pivotal in vascular homeostasis and integrity. However, these cells are perpetually subjected to a myriad of mechanical, chemical, and biological stresses that can compromise their plasma membranes. A sophisticated repair system involving key molecules, such as calcium, annexins, dysferlin, and MG53, is essential for maintaining endothelial viability. These components orchestrate complex mechanisms, including exocytosis and endocytosis, to repair membrane disruptions. Dysfunctions in this repair machinery, often exacerbated by aging, are linked to endothelial cell death, subsequently contributing to the onset of atherosclerosis and the progression of cardiovascular diseases (CVD) and stroke, major causes of mortality in the United States. Thus, identifying the core machinery for endothelial cell membrane repair is critically important for understanding the pathogenesis of CVD and stroke and developing novel therapeutic strategies for combating CVD and stroke. This review summarizes the recent advances in understanding the mechanisms of endothelial cell membrane repair. The future directions of this research area are also highlighted.

In this study, considering the peroxidase-like activity of the SiO₂@AuNPs nanocomposite, their biochemical properties including, pH stability, cycling stability, shelf stability, and kinetic parameters were investigated. The results revealed that the as-mentioned SiO₂@AuNPs nanocomposite reveal its maximal activity at pH=4.0 along with saving 83.3% of its maximal activity at pH=5.0. Besides, the reusability and shelf-storage studies exhibited that the SiO₂@AuNPs nanocomposite retained 90% and 100% of its initial activity after 5 operational cycles and 30 days of storage, in order. The kinetic parameters of the as-prepared nanozymes were calculated using Menten kinetic model, revealing a V_max of 1.35 µM min^-1 and a K_m as low as 0.06 mM for the SiO₂@AuNPs nanocomposite. Based on the results of this work, the as-prepared SiO₂@AuNPs nanocomposite with intrinsic peroxidase-like activity shows high substrate affinity and catalytic efficiency along with excellent cycling- and shelf-stability, making them suitable for application in peroxidase-mediated reactions instead of the native enzyme.

Programmed cell death protein 1 (PD-1) is a biomarker on the surface of cells that has a role in promoting self-tolerance by suppressing the inflammatory activity of T cells. In this work, one peptide of PD-1 was used as the template in molecular imprinting. The magnetic peptide-imprinted poly(ethylene-co-vinyl alcohol) composite nanoparticles (MPIP NPs) were characterized by dynamic light scattering (DLS), high-performance liquid chromatography (HPLC), Brunauer-Emmett-Teller (BET) analysis and superconducting quantum interference device (SQUID) analysis. Natural killer-92 (NK-92) cells were added to these composite nanoparticles and then incubated with human hepatoma (HepG2) cells. The viability and apoptosis pathway of HepG2 were then studied using cell counting kit-8 (CCK8) and the quantitative real-time polymerase chain reaction (qRT-PCR), respectively. These nanoparticles were found significantly enhance the activity of natural killer cells toward HepG2 cells by increasing expression of NK-kB, caspase 8 and especially caspase 3.

Soy protein isolate (SPI) based materials are abundant, biocompatible, renewable, and biodegradable. In order to improve the tensile strength (TS) of SPI films, we prepared a novel composite film modified with microcrystalline cellulose (MCC) and metal nanoclusters (NCs) in this research. The effects of the modification of MCC on the properties of SPI-Cu NCs and Zn NCs films were investigated. Attenuated total reflectance-Fourier transformed infrared spectroscopy analyses and X-ray diffraction patterns characterized the strong interactions and reduction of the crystalline structure of the composite films. Scanning electron microscope showed the enhanced cross-linked and entangled structure of modified films. Compared with untreated SPI film, the tensile strength of the SPI-MCC-Cu and SPI-MCC-Zn films increased from 2.91 MPa to 13.95 and 6.52 MPa, respectively. Moreover, the results also indicated their favorable water resistance with higher water contact angle. Meanwhile, the composite films exhibited increased initial degradation temperatures, demonstrating their higher thermostability. The results suggested that MCC could effectively improve the performance of SPI-NCs films, which would provide a novel preparation method for environmentally friendly SPI-based films in the applications of packaging materials.

The structure of existing activated models is inherently deficient in reflecting the major role of the membrane filtration. This study developed and proposed a novel model, MASM, for the membrane activated process. The effective filtration size imposed by the membrane module, entrapping larger size particles was adopted as the basis of the proposed model. The model defined a modified COD fractionation, accounting for the captured COD fractions as additional model components and utilizing related mass balance relationships. It was implemented for testing the fate of soluble hydrolysable COD and system performance of super-fast membrane activated sludge based on real data for the characterization and process kinetics of domestic sewage and denim processing effluents. Model evaluation was carried for parallel systems with gravity settling and membrane filtration operated at a sludge age range of 0.5-2.0 d. Results reflected significantly better performance of super-fast membrane activated sludge system for both wastewaters, underlining that it was crucially important to account for the captured COD fractions to provide an accurate evaluation of system behavior and effluent quality. This should also be identified as the major shortcoming of the ASM models for evaluating and predicting system performance of activated sludge configurations with membrane separation.

A simple model is developed for membrane fouling, taking into account two main fouling phenomena: cake formation, due to attached solids onto the membrane surface and pores clogging, due to retained compounds inside the pores. The model is coupled with a simple anaerobic digestion model for describing the dynamics of an Anaerobic Membrane BioReactor (AnMBR). In simulations, we investigate its qualitative behavior: it is shown that the model exhibits satisfying properties in terms of flux decrease due to membrane fouling. Comparing simulation and experimental data, the model is shown to predict quite well the dynamics of an AnMBR. The simulated flux best fits the experimental flux with a correlation coefficient r2=0.968 for the calibration data set and r2=0.938 for the validation data set. General discussions are given on possible control strategies to limit fouling and optimize the flux production. We show in simulations that these strategies allow one to increase the mean production flux to 33 L/(h.m2), whereas without control it was 18 L/(h.m2).

Nowadays, the chemical industry is looking for sustainable chemicals to synthesize nanocomposite bio-based polyurethane foams, PUs, with the aim to replace the conventional petrochemical precursors. Some possibilities to increase the environmental sustainability in the synthesis of nanocomposite PUs include the use of chemicals and additives derived from renewable sources (such as vegetable oils or biomass wastes) which comprise an increasing wider base raw materials. Generally, sustainable PUs exhibit chemico-physical, mechanical and functional properties which are not comparable with those of PUs produced from petrochemical precursors. In order to enhance the performances as well as the bio-based aspect, the addition in the polyurethane formulation of renewable or natural fillers can be considered. Among these, walnut shells and cellulose are very popular wood-based waste and due to their chemical composition, carbohydrate, protein and/or fatty acid, can be used as reactive fillers in the synthesis of PUs, diatomite as natural inorganic nanoporous filler can be also evaluated to improve mechanical and thermal insulation properties of rigid PUs. In this respect, sustainable nanocomposite rigid PU foams are synthesized by using a cardanol-based Mannich polyol, MDI as isocyanate source, catalysts and surfactant to regulate the polymerization and blowing reactions, H2O as sustainable blowing agent and suitable amount (5wt%) of ultramilled walnut shell, cellulose and diatomite as filler. The effect of these fillers on the chemico-physical, morphological, mechanical and functional performances on PU foams has been analyzed.

Phosphorus, an essential rare element in aquatic ecosystems, plays a key role in maintaining ecosystem balance. However, an excess of phosphorus will lead to eutrophication and algal pro-liferation. To prevent eutrophication, it is crucial to pretreat and measure the concentration of total phosphorus (TP). Compared with conventional TP pretreatment equipment (autoclave), a lab-on-a-chip detection device fabricated through micro-electromechanical system technology using titania (TiO2) as a photocatalyst is more convenient, efficient, and cost-effective. However, the wide bandgap of TiO2 (3.2 eV) limits the photocatalytic activity. To address this problem, this paper describes the preparation of a TiO2/Au nanocomposite film by electron-beam evaporation and atomic layer deposition, based on the introduction of a gold film and TiO2 on a quartz substrate. The photocatalytic degradation properties of TiO2/Au nanocomposite films with thicknesses of 1, 2, 3, and 4 nm are assessed using rhodamine B as a pollutant. Experimental results demonstrate that the deposition of a gold film with different thicknesses can enhance the photocatalytic degradation efficiency through synergetic reactions in the charge separation process on the surface. The optimal photocatalytic efficiency is achieved when the deposition thickness is 2 nm, and it decreases with further increase in the thickness. When the photocatalytic reaction time is 15 min, the LOC device with a 2-nm-thick gold layer and autoclave exhibit similar TP pretreatment performance. Therefore, the proposed LOC device based on photocatalysis technology can address the limitation of conventional autoclave equipment, such as large volume, long processing time, and high cost, thereby satisfying the growing demand for on-site evaluation.

Ultralong carbon nanotubes (UCNTs) are highly demanded for nanocomposites applications because of their magnificent physical and chemical properties. UCNTs are synthesized by catalytic chemical vapor deposition (CCVD) method and, before using as fillers in nanocomposites, should be purified from residual catalyst and non-CNT particles without significant destruction or scissoring of UCNTs. The role of water vapor for purification of UCNTs is investigated, the importance of water assistance in this process is confirmed. It was shown that wet air treatment of products of UCNTs CCVD synthesis under mild conditions can be used to decrease sufficiently residual catalyst content without significant carbon losses in comparison with the results obtained with dry air, while the residual iron content was shown to influence heavily on the subsequent oxidation of different forms of carbons, including UCNTs. The increasing of D/G ratio of Raman spectra after wet air treatment of products of UCNTs CCVD synthesis makes it possible to conclude that iron catalyst particles transform into iron oxides and hydroxides that caused inner structural strains and destruction of carbon shells improving removal of the catalyst particles by subsequent acid treatment. UCNTs purification with water assistance can be used to develop economically and ecologically friendly methods for obtaining fillers for nanocomposites of different applications.

Extracorporeal membrane oxygenation (ECMO) is used for the management of severe respiratory and cardiac failure, as well as bridge to definite treatment or transplantation. ECMO associated coagulopathy (EAC) is a frequent complication leading to high rates of thrombosis or severe haemorrhage, contributing to morbidity and mortality of patients. Understanding the pathophysiology of EAC is substantial for effectively managing patients on ECMO. We analyse the underlying mechanism of EAC and discuss the monitoring of coagulation profile, combining the viscoelastic point of care assays with the conventional coagulation laboratory tests.

Spin Assisted Layer-by-Layer (SA-LbL) assembly is one of the Layer-by-Layer (LbL) assembly variants. It is considered as the fastest LbL assembly, however, the deficiency of layering quality on bigger polymeric support size poses a significant challenge to the application of SA-LbL assembly at a larger or industrial scale. To address the challenge, combined spin-spray assisted Layer-by-Layer (SSA-LbL) is employed to prepare membrane. In this study, nanofiltration (NF) thin film composite membranes were prepared by alternate deposition of branched-polyethyleneimine (PEI) and poly(sodium 4-styrenesulfonate) (PSS) on polyethersulfone (PES) ultrafiltration (UF) membrane support. The resulting membrane was then tested to separate NaCl from water. One of the membranes produced in this work, i.e., (PEI/PSS)10 achieved rejection rate of 76.2 %; permeability of 2.79 l/h·m2·bar tested at pressure of 10 bar, temperature of 24.58 ± 0.51 °C , and NaCl-Feed concentration of 2076.75 ± 40.51 ppm. The membrane fouling resistance was also examined in 5 days-test. The membrane showed stable performance and lost only about 30% flux from the initial flux due to fouling which was comparable to that of commercial NF membrane such as NF90. Hence, this work shows that SSA-LbL can be considered as a promising and innovative membrane fabrication technique as it offers flexibility and applicability for preparing membrane from various materials as well as pertinence to industrial scale.

Ras is the most frequently mutated oncogene and recent drug development efforts have spurred significant new research interest. Here we will review progress toward understanding how Ras functions in nanoscale, proteo-lipid signaling complexes on the plasma membrane, called nanocluster. We will discuss how G-domain reorientation is plausibly linked to Ras-nanoclustering and -dimerization. We will then look at how these mechanistic features could cooperate in the engagement and activation of RAF by Ras. Moreover, we will show how this structural information can be integrated with microscopy data that provide nanoscale resolution in cell biological experiments. Synthesizing the available data, we propose to distinguish between two types of Ras nanoclusters, an active, immobile RAF-dependent type and an inactive/ neutral membrane anchor-dependent. We conclude that it is possible that Ras reorientation enables dynamic Ras dimerization, while the whole Ras/ RAF complex transits into an active state. These transient di/oligomer interfaces of Ras may be amenable to pharmacological intervention. We close by highlighting a number of open questions including, whether all effectors form active nanoclusters and whether there is an isoform specific composition of Ras nanocluster.

Alginate-silver nanocomposites in the form of spherical beads and films were prepared using a green approach by using the aqueous extract of Ajwa dates seeds. The nanocomposites were fabricated by in situ reduction and gelation method by ionotropic crosslinking using calcium ions in solution. The rich phytochemicals of the dates seeds extract played a dual role as reducing and stabilizing agent in the synthesis of silver nanoparticles. The formation of silver nanoparticles was studied using UV-Vis absorption spectroscopy and a distinct surface plasmon resonance (SPR) peak at 421 nm characteristic of silver nanoparticles confirmed the green synthesis of silver nanoparticles. The morphology of the nanocomposite beads and film was compact with even distribution of silver nanoclusters. The catalytic property of the nanocomposite beads was evaluated for the degradation of 2-nitrophenol in the presence of sodium borohydride. The degradation followed pseudo-first order kinetics with a rate constant of 1.40 ´ 10^-3 s^-1 at 23 °C with an activation energy of 18.45 kJ mol^-1. The thermodynamic parameters such as changes in enthalpy and entropy were evaluated to be 15.22 kJ mol^-1 and -197.50 J mol^-1 K^-1, respectively. The nanocomposite exhibited properties against three clinically important pathogens (Gram-positive and Gram-negative bacteria)

Polymer-derived ceramic (PDC) based coatings like Si-C-N and their derivatives are gaining importance day by day in N/MEMS and aerospace due to their thermos-mechanical stability and conductivity. The crystallized, amorphous, and near amorphous morphology of SiCN nanocomposite coatings based on deposition conditions requires thorough investigation for appropriate utilization as they lead to differences in mechanical properties (quantified using nanoindentation in this case). A 4-stage model was proposed based on Raman spectroscopy due to the N₂-Ar pressure variations during the deposition process of SiCN coatings by magnetron sputtering. The integral intensity of the G (graphitic), disorder (D), and tetrahedral (T) peaks namely I_G, I_D, and I_T were calculated after the deconvolution of the spectra. The sp² domain size and defect parameters were evaluated and correlated with the hardness and different bond formation involving Si, C, and N. Image analysis revealed the atomic migration involved during the growth process leading to crystallization along with the formation of voids and defects. The observations were supported by FTIR and TEM-SAED analysis. The outcomes provide a foundation causing an urge to develop similar models with further elemental additions and correlate with various physical properties.

This study introduces a promising and practical method for the removal of paracetamol from aqueous environments, employing graphene oxide-polymer nanocomposite beads. The approach involves the utilization of a straightforward and facile phase inversion method, offering a convenient and efficient one-step process for the creation of adsorbent beads by integrating polymers and graphene oxide (GO). The synthesized nanocomposite beads are tailored for the removal of paracetamol from simulated wastewater in batch systems. Extensive characterization techniques are employed to scrutinize the chemical properties and structural attributes of the prepared beads. The investigation explores the impact of critical parameters such as adsorbent dosage, adsorption duration, initial paracetamol concentration, and solution pH on the adsorption process. These nanocomposite beads exhibit an exceptional paracetamol removal efficiency, achieving up to 99% removal. This research not only contributes to the advancement of efficient and sustainable adsorbent materials for pollutant removal but also underscores their potential for environmentally friendly and cost-effective solutions in the domain of wastewater treatment.

A nanocomposite rod-shaped structure with single-walled carbon nanotube (SWCNT) embedded in polypyrrole (PPy) doped with nonafluorobutanesulfonic acid (C4F), SWCNT/C4F-PPy, was synthesized using emulsion polymerization. The hybrid ink was then directly coated on a polyimide film interdigitated with the Cu/Ni/Au electrodes via a screen-printing technique to create a flexible film sensor. The sensor film showed a response of 1.72% at 25 °C/atmospheric pressure when acetone gas of 5 ppm was injected, which corresponds to almost 95% compared to the Si wafer-based array interdigitated with the Au electrode. Additionally, C4F was used as a hydrophobic dopant of PPy to improve the stability of humidity and to produce a highly sensitive film-type gas sensor that provides stable detection even in humid conditions.

The optical properties of the Nafion polymer membrane containing colloidal CdSe/CdS/ZnS nanocrystals embedded by diffusion have been studied. The CdSe/CdS/ZnS nanocrystals have a core/shell/shell appearance. A toluene solution was used to provide mobility of the active sul-fone groups of the Nafion membrane and to embed the nanocrystals inside the membrane. The kinetics of the process of nanocrystal embedding into the membrane matrix was studied using luminescence analysis, absorption spectroscopy and laser emission spectroscopy techniques. The diffusion of colloidal CdSe/CdS/ZnS nanocrystals into the Nafion proton exchange membrane resulted in a new molecular complex «Nafion-colloidal CdSe/CdS/ZnS nanocrystals». The pres-ence of new luminescence centers based on CdSe/CdS/ZnS nanocrystals in the membrane was registered using laser emission spectroscopy. Colloidal nanocrystals located in the Nafion ma-trix represent an analogue of a luminescent transducer. The lines contained in the luminescence spectrum of the membrane, which has been in solution with colloidal nanocrystals for a long time, registered upon its drying, show the kinetics of the formation of the molecular complex «Nafion membrane - nanocrystals». The luminescence spectrum of the membrane with nano-crystals contains additional intensity maxima that do not coincide with the spectral lines of the solvent and Nafion membrane. The intensity of the luminescence spectrum of the membrane with embedded nanocrystals is higher than the intensity of the secondary emission peak of the initial nanocrystals, which is important for the practical use of the complex «Nafion-colloidal nanocrystals» in optical systems.

The air is a fundamental element for the life on Earth. Rapid urbanization and industrialization release large amounts of pollutants (harmful gases, microorganisms, and particulate matter, among others) into the atmosphere, leading to health hazards. Air filtration is still the most used and promising technique for protecting air against pollutants. The quality and efficiency of filtering process are dependent of material used for the filter and other filter’s properties. Several methods can be used for manufacturing filters, one of them uses fibrous membranes obtained through electrospinning from polymeric solutions. Electrospinning is a technique that combines the application of an electrostatic field to a moving fluid which results in the fibers formation. Electrospun membranes are constituted by fibers that the sizes spread on submicro and or nanometric scales. This review focuses on fiber membranes obtained by electrospinning for filtration of particulate matter. It is addressed the effect of solution, processing and ambient parameters on the morphology and dimensional characteristics of fiber membranes. The basic principles of air filtration and test and characterization of filter performance are presented. The research progress on electrospun nanofibers as air filters in recent years is summarized and examined. Finally, conclusion and future perspectives in electrospun fibers for air filtration are provided and discussed.

The generation and maintenance of membrane potential is a fundamental part of Membrane Pump Theory. One of the key points of this hypothesis is based on a natural or facilitated molecular diffusion through several types of ion channels and pumps like the Na/K ATPase. Following the principles of chemistry, electrostatics and geometry, it becomes clear that ion channels cannot function in this way. The ions channels cannot by their location have both a filter function and be ion concentrators, and the Na/K pump by its position in the membrane and by the proposed assumptions is not able to perform its regulatory function. The current model must absolutely be revised according to the current state of our knowledge and allow an advance in the understanding of the phenomena opening new research perspectives.

A new method is proposed to increase rejection in microfiltration by applying membrane oscillation using a new type of microfiltration membranes with slotted pores. The oscillations applied to the membrane surface result in reducing membrane fouling and increasing separation efficiency. An exact mathematical solution of the flow in the surrounding solution outside the oscillating membrane is developed. The oscillation results in appearance of the lift velocity, which moves oil particles away from the membrane. The latter results in both reducing membrane fouling and increasing oil droplets rejection. This developed model was supported by the experimental results for oil water separation in produced water treatment. It was proven that oil droplet concentration reduced notably in the permeate due to the membrane oscillation and that applied shear rate caused by the membrane oscillation is also reduce pore blockage. New generation of microfiltration membranes with slotted pores was used in the experiments.

This study proposed the combination system consisting of biogas dry reforming reactor and solid oxide fuel cell (SOFC). Since a biogas dry reforming is an endothermic reaction, this study adopted a membrane reactor operated due to the non-equilibrium state with H2 separation from the reaction space. This study aimed to clarify the characteristics of Ni/Cr/Ru catalyst using for a biogas dry reforming membrane reactor. Additionally, this study also investigated the comparison of the characteristics of Ni/Cr/Ru catalyst with that of Ni/Cr catalyst. The impact of operation temperature, the molar ratio of CH4 : CO2, the differential pressure between the reaction chamber and the sweep chamber and the introduction of sweep gas on the characteristics of the biogas dry reforming membrane reactor using Pd/Cu membrane and Ni/Cr/Ru catalyst was examined. The concentration of H2 using Ni/Cr/Ru catalyst was larger than that using Ni/Cr catalyst by 2871 ppmV for the molar ratio of CH4 : CO2 = 1.5 : 1 at the reaction temperature of 600 ℃ and the differential pressure of 0 MPa without a sweep gas, especially. Under this condition, CH4 conversion, H2 yield and thermal efficiency were 67.4 %, 1.77×10-2 % and 0.241 %, respectively.

This study focuses on a biogas dry reforming to produce H2. Biogas contains CO2 of 40 vol% approximately, indicating that the efficiency of the power generation is reduced because of the smaller heating value compared with a natural gas. The authors have proposed the combination system consisting of biogas dry reforming reactor and solid oxide fuel cell (SOFC). Since a biogas dry reforming is an endothermic reaction, this study adopts a membrane reactor which can be operated by causing the non-equilibrium state with H2 separation from the reaction space. This study aims to clarify the impact of thickness of Pd/Cu membrane on the characteristics of the biogas dry reforming membrane reactor using Pd/Cu membrane and Ni/Cr catalyst. The impact of the operation temperature, the molar ratio of CH4:CO2 and the differential pressure between the reaction chamber and the sweep chamber on the characteristics of the biogas dry reforming membrane reactor using Pd/Cu membrane and Ni/Cr catalyst is examined changing the thickness of Pd/Cu membrane. As a result, the highest concentration of H2 is 122711 ppmV which is obtained in case of CH4:CO2 =1:1 at the reaction temperature of 600 ℃ and the differential pressure of 0 MPa using the Pd/Cu membrane whose thickness of 40 m.

membrane separation technology shows promise, particularly gas separation membranes, including ceramic membrane. Ceramic membranes are increasingly gaining attention for their acid and alkali stability, corrosion resistance, high-temperature tolerance, and mechanical strength. This study focuses on alumina support ceramic membrane for CO2 capture. The membranes were characterized using contact angle measurements, scanning electron microscopy (SEM), and Fourier Transform Infrared spectroscopy (FTIR) analysis. The contact angle measurements confirmed the hydrophilic, while SEM analysis showed even particle distribution in the alumina ceramic membranes respectively. EDAX analysis revealed the elemental composition in the alumina support matrix. FTIR analysis demonstrated chemical interactions of the support membrane. Single gas permeation experiments were conducted. It can be observed that Nitrogen gas permeated faster with increase in feed pressure through the unmodified ceramic inorganic hydrophobic membrane more than the other two single gases, O2, and CO2). As a result, only high permeance separation membranes with realistic size and pressure conditions may be considered of as a practical alternative for CO2 capture. However, the presence of non-selective defects limited the improvement in selectivity of hydrophilic ceramic membrane. In this case, there is need to modify the ceramic membrane used to increase the flux, permeance of CO2, and selectivity of CO2.

Abstract: membrane separation technology shows promise, particularly gas separation membranes, including ceramic membrane. Ceramic membranes are increasingly gaining attention for their acid and alkali stability, corrosion resistance, high-temperature tolerance, and mechanical strength. This study focuses on alumina support ceramic membrane for CO2 capture. The membranes were characterized using contact angle measurements, scanning electron microscopy (SEM), and Fourier Transform Infrared spectroscopy (FTIR) analysis. The contact angle measurements confirmed the hydrophilic, while SEM analysis showed even particle distribution in the alumina ceramic membranes respectively. EDAX analysis revealed the elemental composition in the alumina support matrix. FTIR analysis demonstrated chemical interactions of the support membrane. Single gas permeation experiments were conducted. It can be observed that Nitrogen gas permeated faster with increase in feed pressure through the unmodified ceramic inorganic membrane more than the other two single gases, O2, and CO2). As a result, only high permeance separation membranes with realistic size and pressure conditions may be considered of as a practical alternative for CO2 capture. However, the presence of non-selective defects limited the improvement in selectivity of hydrophilic ceramic membrane. In this case, there is need to modify the ceramic membrane used to increase the flux, permeance of CO2, and selectivity of CO2.

Autophagy is a cellular mechanism that utilizes lysosomes to degrade its own components and is performed using Atg5 and other molecules originating from the endoplasmic reticulum membrane. On the other hand, we identified an alternative type of autophagy, namely, Golgi membrane-associated degradation (GOMED), which also utilizes lysosomes to degrade its own components, but does not use Atg5 originating from the Golgi membranes. The GOMED pathway involves Ulk1, Wipi3, Rab9 and other molecules, and plays crucial roles in a wide range of biological phenomena, such as the regulation of insulin secretion and neuronal maintenance. We here describe the overview of GOMED, the methods to detect autophagy and GOMED, and to distinguish GOMED from autophagy.

In a large variety of organisms, antimicrobial peptides (AMPs) are primary defences against pathogens. BP100 (KKLFKKILKYL-NH2), a short, synthetic, and cationic AMP, is active against bacteria and displays low toxicity towards eukaryotic cells. BP100 acquires an α-helical conformation upon interaction with membranes and increases membrane permeability. Despite the volume of information available, the mechanism of action of BP100, the selectivity of its biological effects, and its applications are far from consensual. In this work, we synthesized a fluorescent BP100 analog containing naphthalimide linked to its N-terminal end, Napht-BP100 (Napht-AAKKLFKKILKYL-NH2). The fluorescence properties of naphthalimides, especially their spectral sensitivity to microenvironment changes, are well established, and their biological activities against different types of cells are known. A wide variety of techniques were used to demonstrate that a-helical Napht-BP100 was bound and permeabilized POPC and POPG LUV. Napht-BP100, different from that observed for BP100, was bound to, and permeabilized POPC LUV. With zwitterionic (POPC) and negatively charged (POPG) containing LUVs, membrane surface high peptide/lipid ratios triggered complete disruption of the liposomes in a detergent-like manner. This disruption was driven by charge neutralization, lipid aggregation, and membrane destabilization. Napht-BP100 also interacted with double-stranded DNA, indicating that this peptide could also affect other cellular processes in addition to membrane destabilization. Napht-BP100 showed superior antibacterial activity, increased hemolytic activity compared to BP100, and may constitute an efficient antimicrobial agent for dermatological use. By conjugating BP100 and naphthalimide antimicrobial properties, Napht-BP100 was bound more efficiently to the bacterial membrane and could destabilize the membrane and enter the cell by interacting with its cytoplasm- exposed DNA.

Polyvinyl guanidineacetic (PVG) was prepared by the chemical grafting between poly(vinyl alcohol) (PVA) and guanidineacetic acid. The results showed that the guanidineacetic groups were successfully introduced into the polyvinyl alcohol by fourier transform infrared (FTIR) and thermogravimetry (TG). The effects of the amount of catalyst and reaction time on the PVG grafting rate were investigated. The PVG/NWF composite membrane as a heterogeneous catalyst for biodiesel production was successfully prepared by the solvent phase inversion. The effects of mass ratio of methanol/soybean oil and reaction temperature on the conversions using the composite membrane for transesterification were studied. And the reusability of the composite membrane and the kinetics of the reaction catalyzed by the composite membrane were also investigated. The conversions obtained from the model are in good agreement with the experimental data.

African trypanosomes are an early branch in eukaryotic evolution and developed a unique endomembrane system as an adaptation to their parasitic life style. The key virulence mechanism of many pathogens is successful immune evasion to enable survival within the host, which is a feature requiring both genetic events and membrane transport in African trypanosomes. Intracellular trafficking not only plays a role in immune evasion, but also in homeostasis of intracellular and extracellular compartments and interactions with the environment. Significantly, historical and recent work has unravelled some of the connections between these processes and highlighted how immune evasion mechanisms associated with adaptations in membrane trafficking may have, paradoxically, provided specific sensitivity to drugs. Here we explore these advances in understanding the membrane composition of the trypanosome plasma membrane and organelles and provide a perspective for how transport could be exploited for therapeutic purpose.

The global polyvinyldene flouride market is estimated to reach $937,278.5 thousand by 2019, therefore to develop new membranes and gain pioneering ideas, which could create innovative business opportunities, a fundamental knowledge about membrane properties fabricated from recent commercially available PVDF polymers is highly mandatory. In this study, we successfully prepared nine non-woven supported PVDF membranes using a phase inversion precipitation method starting from a 15 wt% PVDF solution in N-methyl-2-pyrrolidone. Various membrane morphologies were obtained by using (1) PVDF polymers with diverse molecular weight in a range from 300.000 Da to 700.000 Da and (2) different temperatures of the coagulation bath (20, 40, and 60 ±2°C) used for the films precipitation. Environmental Scanning Electron Microscope (ESEM) was used for surface and cross-section morphologies characterization. Atomic Force Microscope (AFM) was employed to investigate surface roughness, while Contact Angle (CA) instrument was used for membranes wettability studies. Fourier Transform Infrared Spectroscopy (FTIR) results show that the fabricated membranes are formed by a mixture of TGTG’ chains in α phase crystalline domains and all-TTTT trans planar zigzag chains characteristic to β phase. Moreover, generated results indicate that the phases content and membrane morphologies depend on the polymer molecular weight and conditions used for the membranes preparation. The diversity of fabricated membranes could be applied by the End User Industries for different applications.

Nowadays there is a growing interest in membrane modification processes, to improve their characteristics, the effectiveness of their treatments and reduce the possible fouling. In this sense, in this work a modification of an ultrafiltration membrane with tree different materials has been carried out: reduced graphene oxide (rGO), chitosan and MgCl2. For both the native and the modified membranes, a study has been carried out to remove the emerging contaminant sul-fomethoxazole. SEM and SEM-EDX analyses have been performed to confirm membrane surface modifications. In the characterization of the membranes, it is noteworthy that the values of the permeability coefficient, Aw, have been lower in the modified membranes, which is unexpected. Regarding the pollutant removal tests, the influence of pressure and initial concentration on permeate flows and rejections has been studied. Native membrane shows the highest permeate flow values. Comparing the modified membranes, the highest rejection values are obtained with the rGO-modified membrane, which can be explained by its greater hydrophilic character. Finally, a fouling study has been carried out, verifying that in almost all cases such fouling occurs after the passage of the pollutant, due to the blockage of the membrane pores.

Mesoporous MgAl2O4+ LnFe0.7Ni0.3O3 (Ln=La, Pr) nanocomposites were prepared by inexpensive one-pot procedure with Pluronic P123 copolymer, Ni+Ru active component was supported by wet impregnation. The real structure of samples was studied by XRD and TEM with EDX, surface properties by FTIRS of adsorbed CO, reactivity by H2 –TPR, catalytic activity was tested in ethanol steam reforming. Disordering of the real structure of nanocomposite supports due to incorporation of transition metal cations into MgAl2O4 results in developed metal-support interface and domination of single surface metal centers. This provides a high catalytic activity in reaction of ethanol steam reforming in the intermediate temperature range ~550 oC close to that of the best known catalysts, and stability to coking. A higher activity for Pr-containing catalyst is provided by a high reactivity of surface oxygen species bound with Pr cations.

We are presenting a new method for the treatment of large macular holes (MH) with the use of an inverted flap consisting of both internal limiting membrane (ILM) and epiretinal proliferation (EP). A prospective interventional case series was conducted from September 2021 to January 2023. MH patients with coexistent EP visualized preoperatively in macula optical coherence tomography and MH minimum linear diameter larger than 400 microns underwent standard pars plana vitrectomy with the creation of an inverted petaloid flap (consisting of both ILM and EP) and gas tamponade. 16 eyes were included in our study. MH closure was successful in all the eyes with a single procedure. Preoperative minimum linear diameter was 707.63(±164.02μm) and preoperative best corrected visual acuity was 1.11±0.52. Postoperative BCVA was 0.51±0.20 (p=0.01) at 6weeks postoperatively and final BCVA was 0.45±0.20 (p=0.008). EP can be safely combined with ILM for the creation of an inverted, petaloid flap to cover and facilitate the closure of large MH.

Hepatocellular carcinoma (HCC) is a heterogeneous malignancy with complex carcinogenesis. Although there has been significant progress in the treatment of HCC over the past decades, drug resistance to chemotherapy remains a major obstacle in its successful management. In this study we were able to reduce chemoresistance in cisplatin-resistant HepG2 cells by either silencing the expression of transglutaminase type 2 (TG2) using siRNA or by pre-treatment of cells with the TG2 enzyme inhibitor cystamine. Further analysis revealed that, whereas the full-length TG2 isoform (TG2-L) was almost completely cytoplasmic in its distribution, the majority of the short TG2 isoform (TG2-S) was membrane-associated in both parental and chemoresistant HepG2 cells. Following induction of cisplatin toxicity in non-chemoresistant parental cells, TG2-S together with cisplatin quickly relocated to the cytosolic fraction. Conversely, no cytosolic relocalisation of TG2-S or nuclear accumulation cisplatin was observed following identical treatment of chemoresistant cells, where TG2-S remained predominantly membrane-associated. This suggests that deficient subcellular relocalisation of TG2-S from membranous structures into the cytoplasm may limit the apoptic response to cisplatin toxicity in chemoresistant cells. Structural analysis of TG2 revealed the presence of binding motifs for interaction of TG-S with the membrane scaffold protein LC3/LC3 homologue that could contribute to a novel mechanism of chemotherapeutic resistance in HepG2 cells.

In contrast to the traditional fillers, clay, in particular, natural smectite clay represents an environmentally significant alternative to improve the properties of polymers. Compared to con-ventional nanofillers, smectite clay can effectively enhance the physical and mechanical properties of polymer nanocomposites with a relatively small amount of addition (< 5 wt%). The present study focuses on investigating the reinforcing efficiency of different amounts (up to 5 wt%) of a natural Brazilian smectite clay on the mechanical and thermal properties of poly(butylene terephthalate) (PBT) nanocomposites. Natural Brazilian clay modified by addition of quaternary salt and sodium carbonate (MBClay) was infused into the PBT polymer by melt extrusion, using a twin-screw extruder. It was found that the best properties for PBT were obtained at 3.7 wt% of modified BClay. Tensile strength at break exhibited an increase of about 60 %, flexural strength increased by 24 % and flexural modulus increased by 17 %. In addition, an increase in the crystallinity percentage of PBT/BClay nanocomposite was confirmed by DSC and XRD analysis, and a gain of about 45 % in HDT was successfully achieved due to incorporation of 3.7 wt% of MBClay.

Proton exchange membrane (PEM) fuel cells have emerged as a viable alternative energy production source for stationary and transportation applications. Reliable and sustainable fuel cell operation requires effective water management. Membrane water content can vary along the stack during transients which can lead to losses in fuel cell performance. To control these variations a model that predicts the internal humidity dynamics of the stack is needed. In this study, a control-oriented model for predicting membrane water content variation was developed and implemented in MATLAB/Simulink. A lumped parameter model was initially developed and then further discretized into smaller control volumes to track humidity distribution along the stack. To validate the model’s predictions, the predicted results were compared to computer simulation results from GT-Suite. The root mean square error (RMSE) between the model’s prediction and GT-Suite’s simulation results was found to be within 1.5 membrane water content for all cases, demonstrating the model’s capability to capture the variation of membrane water content along the stack. The developed model will be useful for real-time control of membrane water content variation in PEM fuel cells.

Toxic metal wastewater is a challenge for exposed terrestrial, aquatic environments and the recyclability of the water, prompting inputs for the development of promising treatment methods. Consequently, the rGO/ZnONP nanocomposite was synthesized at room temperature for four hours and was tested for adsorption of cadmium and lead in wastewater. The optimized nanocomposite had the lowest band gap energy (2.69 eV) and functional group interactions were at 516, 1220, 1732, 3009, and 3460 cm-1. The nanocomposite showed saturation of ZnO nanoparticles on rGO with a weight percentage of zinc (60.02 %), oxygen (22.96 %), and carbon (16.58 %), and the micrograph showed slight agglomeration on the sheet surface. The nanocomposite’s D and G band intensities were almost the same constituting the ZnO presence on rGO from the raman spectrum. The adsorption equilibrium time for cadmium and lead was reached within 10 and 90 minutes with efficiencies of ~ 100 %. Sips and Freundlich were best fitting the cadmium and lead adsorption data (R2 ~ 1), therefore the adsorption was a multilayer coverage for lead and a mixture of heterogenous and homogenous coverage for cadmium adsorption. Both adsorptions were best fitted by the pseudo first order model, suggesting the multilayer coverage dominance. The adsorbent was reused for three and seven times for cadmium and lead. The nanocomposite showed selectivity towards lead (95 %) and cadmium (100 %) in the interfering wastewater matrix. Conclusively, the nanocomposite may be embedded within upcoming lab-scale treatment plants which could lead to further upscaling and serving as industrial wastewater treatment material.