Negative temperature coefficient (NTC) materials are usually based on ceramic semiconductors and electrons are involved in their transport mechanism. A new type of NTC material, adequate for alternating current (AC) applications, is represented by zeolites. Indeed, zeolites are single-charge carrier ionic conductors with a temperature-dependent electrical conductivity. In particular, electrical transport in zeolites is due to the monovalent charge-balancing cations, like K⁺, capable of hopping between negatively charged sites in the aluminosilicate framework. Owing to the highly non-linear electrical behavior of the traditional electronic NTC materials, the possibility to have alternative types of materials, showing linearity in the electrical behavior, is very desirable. Among different zeolites, the natural clinoptilolite has been selected for investigating the NTC behavior since it is characterized by high zeolite content, convenient Si/Al atomic ratio, good mechanical strength, due to its compact microstructure, and low toxicity. Clinoptilolite has shown a rapid and quite reversible impedance change under heating, characterized by a linear dependence on temperature. X-ray diffraction (XRD) has been used to identify the natural zeolite, to establish all types of crystalline phases present in the mineral, and to investigate the thermal stability of these phases up to 150°C. X-ray photoelectron spectroscopy (XPS) analysis has been used for the chemical characterization of the natural clinoptilolite sample, providing important information on the cationic content and framework composition. In addition, since electrical transport takes place in the zeolite free-volume, a Brunauer–Emmett–Teller (BET) analysis of the mineral has been also performed.

Pipeline conflicts arising from data dependencies are a common issue encountered in the hardware implementation of layered QC-LDPC decoders. This paper proposes an efficient layered decoding architecture to reduce pipeline conflicts without introducing stall cycles, by reordering the processing order offline and using the patch method based on variable-to-check message. The experimental results on the LDPC code of the IEEE802.16 standard in the OFDM-PON system demonstrate that the proposed architecture has a sensitivity improvement of 0.125 dBm and 0.375 dBm, respectively, compared with our previous work and the method described in the other work.

The continuous casting process of helical fiber reinforced metal matrix composites was proposed, and the experimental equipment was designed and manufactured. The relationship model be-tween the process parameters and the helical shape of the fibers in the metal matrix is analyzed by differential geometry. Helical carbon fiber reinforced lead matrix composites were prepared under different conditions. When the melting temperature and cooling intensity were increased, the helical radius of helical carbon fiber in lead matrix was increased. When the fiber rotation speed was increased, the helical radius was decreased, and the helical pitch was de-creased proportionally. The experimental results are consistent with the process model. Carbon fiber rein-forced aluminum composites were prepared. Scanning electron microscopy showed that the infiltration between the aluminum matrix and the carbon fiber was not complete. As the volume fraction of carbon fiber which was added in composites is too small, the mechanical properties of the composites have not been significantly improved.

Yttria stabilized zirconia (Y-TZP) ceramics with drastically reduced yttria content have been introduced by different manufacturers aiming at improving the damage tolerance of ceramic components. In this study an alumina doped 1.5Y-TZP was axially pressed, pressureless sintered in air at 1250–1400 °C for 2 h and characterized with respect to mechanical properties, microstructure and phase composition. The material exhibits a combination of high strength of 1000 MPa and a high toughness of 8.5–10 MPa√m. The measured fracture toughness is, however, extremely depending on measurement protocol. Direct crack length measurements overestimate toughness due to trapping effects. The initially purely tetragonal material has a high transformability of > 80 %, the transformation behavior is predominantly dilatoric, measured R-curve related toughness increments are in good agreement with transformation toughness increments derived from XRD data.

Yttria stabilized zirconia materials are frequently used in mechanical engineering and biomedical applications. Demanding loading conditions require materials combining a high level of strength and fracture toughness. A ready to press alumina doped 2 mol% yttria stabilized zirconia powder was shaped by axial pressing and sintering in air at 1250 - 1500 °C for 2 h. The best combination of strength and toughness value of 7.8 MPa√m. Materials sintered in the middle of the chosen temperature range combine fully density, high transformability and small grain size. Toughness measurements by direct crack length measurements delivered unrealistically high fracture toughness values.

A comprehensive modeling framework for the thermoforming of polymer matrix woven laminate composite was developed. Two numerical indicators, the slip path length and traction magnitude, have been identified to be positively correlated to matrix smearing and wrinkling defects. The material model has been calibrated with picture-frame experimental results, and the prediction accuracy for intra-ply shear and thickness distribution were examined with measurements on the physically formed parts. Finally, a parametric study was conducted to determine the relationship between various process parameters and the quality of the formed part. For the trapezoidal part, orienting the laminate at 45-degrees to the mold axis reduces the likelihood of matrix smear and wrinkling defects. Although this laminate orientation yielded a greater spatial variation of part thickness, the thickness deviation is lower than that for the 0-degree orientation case. Higher forming rates were found to result in more defects due to increased slip path lengths and traction magnitudes. Optimal forming speeds should balance rapid shaping within the operating temperature window while avoiding tear. It was discovered that shallower molds benefit from faster ramp rates, while deeper molds require slower rates to manage extensive shearing, stretching, and bending. Faster forming rates lead to smaller thickness increases at high intra-ply shear regions, indicating a shift from intra-ply shear to out-of-plane bending due to the visco-plastic effect of the molten laminate, and can negatively impact part quality. Lastly, it was shown that a well-conceived strategy using darts could improve the part quality by reducing the magnitude of the defect indicators.

An optical fiber scale sensor based on the detection principle of surface plasmon resonance (SPR) was developed for the rapid, high-sensitivity real-time evaluation of scale precipitation from geothermal fluids. The optical fiber SPR scale sensor was fabricated by depositing a gold thin film on the surface of an optical fiber with an exposed core. The optimal gold film thickness of the sensor was determined to be 30 nm, which achieved a refractive index sensitivity of 2140 nm per refractive index unit. A field test was conducted using geothermal brine from the Obama Binary Geothermal Power Plant in Unzen, Nagasaki Prefecture. A conventional optical fiber scale sensor and the SPR sensor were simultaneously assessed using raw and pH-adjusted brines. For the SPR sensor, a peak shift of 0.27 nm/min was observed at a response time of 1 min, whereas no change in transmittance was observed for the conventional sensor until 180 min. After the experiments, scanning electron microscopy–energy-dispersive spectroscopy analysis was conducted on the sensors, and findings showed that the deposition of Mg–SiO2 scale did not significantly differ between the two sensors. The developed SPR sensor achieved faster scale precipitation detection (tens of minutes to hours) than the conventional sensor.

Amidst escalating environmental concerns, short natural fiber thermoplastic (SNFT) biocomposites have emerged as sustainable materials for the eco-friendly production of mechanical components. However, their limited durability has prompted research into the experimental evaluation of the deterioration of the mechanical characteristics of SNFT biocomposites, particularly under the influence of ultraviolet rays. However, conducting tests to evaluate the mechanical properties can be time-consuming and expensive. In this study, an artificial neural network (ANN) model was employed to predict the mechanical properties (tensile strength) and the impact performance (resistance and absorbed energy) of polypropylene reinforced with 30 wt.% short flax or wood pine fibers (referred to as PP30-F or PP30-P, respectively). Eight parameters were collected from experimental studies. The ANN input parameters comprised nondestructive test results, including mass, hardness, roughness, and natural frequencies, while the output parameters were the tensile strength, the maximum impact load and absorbed energy. The model was developed using the ANN toolbox in MATLAB. The linear coefficient of correlation and mean squared error were selected as the metrics for evaluating the performance function and accuracy of the ANN model. They calculate the relationship and the average squared difference between the predicted and actual values. The data analysis conducted by the models demonstrated exceptional predictive capability, achieving an accuracy rate exceeding 96%, which was deemed satisfactory. For both the PP30-F and PP30-P biocomposites, the ANN predictions deviated from the experimental data by 3, 5, and 6% about the impact load, absorbed energy, and tensile strength, respectively.

Background: Fiber-reinforced composites (FRCs) have been proposed as an alternative to traditional metal alloys for the realization of frameworks in full-arch implant supported prostheses. The aim of the present in vitro study was to evaluate the deflection under load of seven prostheses endowed with frameworks made of different materials, including different types of fiber reinforced composites (FRCs). Methods: A master cast with four implant analogues in correspondence of the two lateral incisors and the two first molars was used to create full-arch fixed prostheses with the same shape and different materials. Prostheses were made in different materials (framework+veneering material): gold alloy+resin (Au+R), titanium+resin (Ti+R), FRC with multi-directional carbon fibers+resin (ICFRC+R), FRC with unidirectional carbon fibers+composite (UCFRC+C), FRC with glass fibers+resin (GFRC+R), FRC with glass fibers+composite (GFRC+C), resin (R, full-acrylic prosthesis). Flexural tests were conducted using Zwick/Roell Z 0.5 machine and the deflection of the lower surface of the prosthesis was measured in order to obtain load/deflection graphs. Results: Greater rigidity and less deflection were recorded for UCFRC+C, GFRC+C, followed by Ti+R, and Au+R. The greatest deformations were observed for resin alone, ICFRC+R and GFRC+R. The results were slightly different in the incisal region probably due to the greater amount of veneering material in this area. Conclusions: When used to realize full-arch frameworks, Au and Ti allow a predictable mechanical behavior with gradual deformations with increasing load. UCFRC also demonstrated good outcomes and less deflection than ICFRCs when loaded. The GFRC full-arch framework may be a valid alternative, however showed greater deflections. Further studies are needed in order to evaluated how different prosthesis design and material thickness might affect the outcomes.

Despite polycarbonate (PC) being a widely used engineering plastic, its notch and crack sensitivity pose challenges in critical applications. To address this, PC was blended with elastomeric polymers to explore the improvement in toughness. This study systematically investigates the toughening mechanisms of PC blended with acrylonitrile-butadiene-styrene (ABS), copolyether ester elas-tomer (COPE), and ABS and styrene-ethylene-butylene-styrene (SEBS) copolymer grafted with maleic anhydride (MA). The morphology and mechanical behavior were evaluated under qua-si-static and high-speed tensile tests and Charpy impact tests using optical, electronic, and atomic force microscopy and Raman spectroscopy. The morphological analysis reveals cavitation and crazing phenomena for COPE and SEBS-g-MA systems, and mostly debonding for ABS, indicating an improvement in toughening. While the addition of ABS improves the PC plastic deformation, modifying ABS with maleic anhydride enhances the elastic modulus. Blending PC with SEBS-g-MA increases the strain at break, and the addition of COPE significantly improves the deformation behavior of PC (by around 115%). This comparative study provides valuable insights into the performance of different PC-elastomer blends under similar conditions, supporting the selection of appropriate materials for given applications.

The interest in obtaining new composite materials with diverse properties has created a growing interest in natural fi-bers as reinforcement in polymers, which has generated an impact in sectors such as automotive and construction, dis-placing synthetic fibers. Properties such as low density, low cost, and rene.wable make these fibers an attractive alterna-tive to reduce environmental impact. Their application in polymers, such as polypropylene, polyethylene, and epoxy resins, has allowed the modification of polymeric composite materials' mechanical and physical properties (NFRP). This review focuses on investigating the status of natural fiber-reinforced polymers. It analyzes their worldwide demand, chemical characteristics, physical and mechanical properties, and various applications in different sectors and indus-tries. In addition, the advantages and disadvantages of NFRPs are highlighted, highlighting their potential for new ap-plications.

Fiber-opening treatment of commingled yarns consisting of thermoplastic nylon fibers and carbon fibers could produce superior CFRTP, but few studies toward that end have been conducted. In this study, we investigated whether an open weave fabric consisting of commingled yarns made of carbon and nylon fibers could shorten the impregnation distance of resin to carbon fibers, and there are few reports on the design of fabrics by opening carbon fiber bundles consisting of commingled yarns. From this study, following are cleared. The impregnation speed of the nylon resin on the carbon fiber was very fast, less than 1 minute. As the molding time increased, the tensile strength and tensile fracture strain slightly decreased and the nylon resin deteriorated. The effects of molding time on flexural strength, flexural modulus, and flexural fracture strain were negligible. From the cross-sectional observation conducted to confirm the impregnation state of the matrix resin, no voids were observed in the molded products regardless of molding time or molding pressure, indicating that resin impregnation into the carbon fiber bundle of the open-fiber mixed yarn fabric was completed at a molding pressure of 5 MPa and a molding time of 5 min.

In this study a material based on Polyethylene (PE) and Microcrystalline Cellulose (MC) was developed as a breathable packaging film. Surface functionalization of MC with 3 aminopropyltriethoxysilane (APTES) shows to be an efficient alternative to tailor their properties and increase opportunities for the application of MC on the reinforcement of polymers such polyethylene (PE). Functionalization of MC with mentioned silane derivative was achieved using a green method and later used on the development of composites with PE in three percentages (1, 3 and 5%). All the materials were prepared by melt blending and characterized, in terms of structural properties (ATR-FTIR and FTIR in transmittance, EDX, SEM), thermal properties (DSC and TGA), thermomechanical properties (DMA), contact angle measurements and permeability to oxygen and water vapor. The materials demonstrated to have potential to be used as breathable film packaging of fresh products.

Extinction of natural resources builds up pressure on governments to invest in research to find more sustainable resources for construction sector. Earlier studies on mortar and concrete show that bottom ash and basalt fiber are independently alternative binder in the concrete sector. This study aims to use bottom ash and basalt fiber blends as alternative novel-based composites in pure cement paste. Strength and durability properties of two different percentages of bottom ash (40% and 50%) and three volume fractions of basalt fiber (0.3%, 0.75%, and 1.5%) were used at three curing periods (7, 28, and 56 days). In order to measure physical properties of the basalt-reinforced bottom ash cement paste composites flowability, dry unit weight, porosity and water absorption measurements at 7, 28, and 56 days of curing were performed. Furthermore, mechanical properties of composites determined by unconfined compressive strength and flexural strength tests. Finally, to assess the durability sulfate-resistance and seawater-resistance tests have been performed on composites at 28 and 56 days of curing. Results showed that addition of basalt fiber improves physical, mechanical and chemical stability properties of paste up to a limiting basalt fiber addition (0.3% volume fraction) where above an adverse effect have been monitored. It is clear that observed results can lead to development of sustainability strategies in the concrete industry by utilizing bottom ash and basalt fiber as an alternative binder.

Fiber-reinforced mycelium (FRM) composites offer an innovative and sustainable approach to construction materials for architectural structures. Mycelium, the root structure of fungi, can be combined with various natural fibers (NF) to create a strong and lightweight material with environmental benefits. Incorporating NF like hemp, jute, or bamboo into the mycelium matrix enhances mechanical properties. This combination results in a composite that boasts enhanced strength, flexibility, and durability. Natural FRM composites offer sustainability through the utilization of agricultural waste, reducing the carbon footprint compared to conventional construction materials. Additionally, the lightweight yet strong nature of the resulting material makes it versatile for various construction applications, while its inherent insulation properties contribute to improved energy efficiency in buildings. Developing and adopting natural FRM composites showcase a promising step towards sustainable and eco-friendly construction materials. Ongoing research and collaboration between scientists, engineers, and the construction industry will likely lead to further improvements and expanded applications. This article provides a comprehensive analysis of the current research and applications of natural FRM composite for innovative and sustainable construction materials. Additionally, the paper reviews the mechanical properties and potential impacts of these natural FRM composites in the context of sustainable architectural construction practices. Recently, the relevance of mycelium-based materials has extended beyond their original fields of microbiology and mycology to architecture.

Monte Carlo techniques have been extensively used for planning laser-based clinical procedures such as photobiomodulation. However, the effect of several biological tissue characteristics, including morphological structure and physiological parameters, has not been carefully addressed in many applications. Specifically, many questions remain concerning the effect of skin phototype and body mass index on the efficacy of photobiomodulation for extraoral therapies. To address these questions, a Monte Carlo simulation model was developed to analyze the effects of body mass index-dependent skin structure and Fitzpatrick skin type, specifically tailored for the morphological characteristics of cheek tissue. The model describes the settings of a typical oral photobiomodulation treatment protocol for pain relief, namely the use of 660 nm and 808 nm laser wavelengths and a therapeutic dose of 2.0 J/cm² on the masseter muscle. The simulations were used to train a machine learning predictive model aimed at accelerating the treatment planning stage and assessing the importance of patient-specific parameters. A multiple regression approach was adopted to predict muscle dose and treatment time for the effective delivered dose.

This research investigates fiber-reinforced cementitious composites, with a particular emphasis on the geometric properties of soft micro and macro fibers. These fibers are characterized by a lower elastic modulus and larger aspect ratios than steel fibers. The composites were manufactured using a cement-to-sand ratio of 1:2.5, with 20% fly ash serving as a partial substitute. In order to attain varying strengths, two water-to-binder ratios (0.55 and 0.60) were implemented. Synthetic fibers, such as carbon and polypropylene, and natural sisal fibers, were introduced in volumes varying from 0.4% to 2.27%, with aspect ratios ranging from 71 to 3750. The flexural strength and behavior were evaluated using 75x75x380 mm prisms, while the compressive strength was measured using 50 mm cubes. Load-deflection curves were developed to investigate fracture behavior. The behavior of specimens reinforced with fibers post-cracking is dependent upon the matrix compressive strength, fiber type, quantity, and aspect ratio. A regression analysis was conducted on data from this study and previous publications to develop an equation that predicts the ratio of modulus of rupture (MOR) to initial fracture strength. The variables are matrix strength and fiber characteristics. The results reveal that carbon fiber-reinforced composites (CFRCCs) exhibit considerable brittleness post-cracking, despite exhibiting a flexural strength that is two to three times greater than that of control specimens. When workability is not compromised, the maximal load capacity and deflection are improved by increasing the fiber volume and aspect ratio. The maximal load stress is more significantly influenced by volumes of fibers than by aspect ratio.

Organic soil amendments, such as composts, mitigate the environmental burdens associated with wasting organic resources. Although compost application to soil enhances an agroecosystem's capacity to store carbon and produce food, studies investigating the agronomical efficacy and their ability to ameliorate drought stress when used as a soil amendment are minimal. In this study, we produced and used a nutrient rich co-compost through the composting of sludge, a nitrogen-rich organic material with carbon rich municipal solid wastes (MSW) to evaluate the agronomic efficacy of the MSW derived co-compost and their ability to ameliorate drought stress. Application of co-compost significantly enhanced growth and yield of lettuce and maize, by a magnitude comparable to chemical fertilizers. Furthermore, under drought stress, lettuce plants grown under co-compost soil amendment grew much better with less wilting, more biomass and yield, and improved root growth. Also, co-compost application enhanced relative root mass ratio (RRMR) under drought stress, indicative that co-compost amendment increased the allocation of biomass to the roots, which is an important morphological attribute for drought adaptability. K content in both leaves and roots of plants amended with co-compost was also higher under drought stress, which may have played a role in osmotic adjustment, consequently, the plants exhibited higher leaf relative water content (RWC). Other nutrient elements that were significantly enhanced by co-compost application included Mg, Ca, Fe and Cu. These results provide evidence that MSW co-composting could optimize organic resource recycling for climate change mitigation and agricultural productivity while minimizing nutrient losses from agroecosystems.

Successful translation of biofortified orange maize (BOM) to a household staple food is dependent on farmers’ ability to cultivate the maize and it subsequent utilization. In this study, we assessed farmers ‘allocation of their land to cultivation of BOM and con-ventional white maize (CWM) varieties in districts where AFI-KEPO Nutrition Program is implemented in Malawi. Results show farmers were skeptical of allocating more land to cultivation of BOM. CWM was allocated significantly more land (1.75 ± 0.51 acres) than BOM (1.12 ± 0.32 acres) (p

It is well known that fiber sizing is one of the most important component in the manufacturing of composites, and it does affect the mechanical properties including strength and stiffness. In this work, the influence of fiber sizing levels on the mechanical properties of carbon fibers (CF) is reported at room temperature by using single fiber tensile testing (Favimat+), single fiber pullout testing (SFPO), and interfacial elemental analysis using X-ray photoelectron spectroscopy (XPS). Standard modulus of CF (7±0.2 μm in diameter) were sized using two Michelman commercially available sizing formulations. The average solid content for each sizing formulation is 26.3 ± 0.2% and 34.1 ± 0.2%, respectively. HEXION RIMR 135 with curing agent RIMH 137 was used as a model thermoset epoxy matrix during the SFPO measurements. A predictive engineering fiber sizing methodology is also developed. Sizing amounts of 0.5, 1, and 2 wt. % on the surface of the fiber is achieved for both sizing formulations. For each fiber sizing level, 50 single fiber tensile testing experiments and 20 single fiber pull-out tests were conducted. The ultimate tensile strength (σult) of the carbon fibers and the interfacial shear strength (τ_app) of the single fiber composite were analyzed. it is also investigated the effect of the sizing levels on the interfacial shear stress and the O/C (Oxygen/Carbon) surface composition ratio. As a result, generalized fiber sizing and characterization methods were established. The developed methods can be used to characterize the strength and interfacial shear strength of any man-made fibers with different sizing formulations and solid contents, irrespective of the matrix i.e. thermoset or thermoplastic.

.With the increasing use of carbon fiber reinforced plastics in various area, carbon fiber composites based on prepregs have attracted attention in industries and academia research. However, prepreg manufacturing processes are costly, and the strength of structures varies depending on the orientation and defects (pores and delamination). For non-contact evaluation of internal defects, we proposed lock-in infrared thermography to investigate orientation angles after a compression test. We also conducted a drop-weight impact test to study the behaviour of the composites after impact according the fibers orientation for composite fabricated using unidirectional carbon fiber prepregs. Using CAI tests, we determined the residual compressive strength and confirmed the damage modes using a thermal camera. The results of the drop weight impact tests show that the specimen laminated at 0° suffered the largest damage because of susceptibility of the resin to impact. In contrast, the specimens oriented in of 0°/90° and +45°/–45° directions transferred more than 90% of the impact energy back to the impactor because of the lamination of fibers in the orthogonal directions. Furthermore, the specimens that underwent complete damage in the impact tests were subjected to the lock-in method and showed internal delamination and cut fibers. With the finite elements analysis, the damage of each ply could be observed. Moreover, the temperature differences in the residual compression tests were not significant.

The use of plant fibers as reinforcement in composites with the aim of totally or partially replacing synthetic fibers has received significant attention in the last years. However, one of the disadvantages of the use of these fibers in polymeric composites is associated to the fact that they are hydrophilic, resulting in poor adhesion with most matrices when in the presence of moisture. In addition, another problem encountered is the lower strength of this type of fiber and, as a solution to minimize these problems, the composite can be hybridized by adding layers of natural and synthetic fibers and the use of resin protection along the thickness of the composite. (Lateral protection) to reduce moisture absorption by the laminate. The objective of this work is to obtain composites formed by five layers of reinforcement and terephthalic polyester matrix, one of which is reinforced only with short glass fiber-E blanket, another reinforced only with jute fiber and a third hybrid containing the fibers. Two types of reinforcements with interlayer layers. Afterwards, the loss of mechanical properties was observed when these materials were immersed in distilled water, with and without lateral protection, until reaching saturation. We evaluated parameters such as the influence of configuration type and environmental conditions, such as the amount of water absorption. The obtained results show that the hybrid composite obtained a behavior close to the composite containing only fiberglass, and better than the one containing only jute fiber and that the absorption was smaller in the samples with side protection.

This review paper presents a comprehensive synthesis of current knowledge on the contamination of water systems by polycyclic aromatic hydrocarbons (PAHs). PAHs, organic contaminants characterized by two or more fused aromatic rings, are notably problematic due to their persistence, bioaccumulation, and significant health risks. The review commences with an examination of various sources of PAHs in aquatic environments, encompassing both anthropogenic activities, such as industrial discharges, urban runoff, and oil spills, and natural phenomena including volcanic eruptions and wildfires. Subsequently, the discussion shifts to the distribution patterns of PAHs within different aquatic ecosystems, with an analysis of factors that influence their transport. Considerable focus is placed on the entry mechanisms of PAHs into water systems and their interactions with diverse environmental matrices. Additionally, the ecotoxicological effects of PAHs on aquatic life are scrutinized, with particular emphasis on molecular, individual, and ecosystemic impacts. This includes an exploration of PAH bioaccumulation in aquatic organisms and their potential mutagenic and carcinogenic consequences. The review further addresses the challenges associated with detecting and quantifying PAHs in aquatic settings, reflecting on the advancements in analytical methodologies and the complexities introduced by their varied physicochemical properties. The paper concludes with a summary of existing regulatory frameworks and guidelines governing PAH contamination in water systems, underscoring the imperative for global collaboration in the monitoring and management of PAH pollution.

Disposable surgical gowns are usually made from petroleum-based synthetic fibers that do not naturally decompose, impacting the environment. A promising approach to diminish the environmental impact of disposable gowns involves utilizing natural fibers and/or bio-based synthetic fibers. In this study, composite web from polylactic bicomponent fiber and natural fibers, cattail and kapok fiber, were prepared by hot-press method. Only the sheath region of the PLA bicomponent fiber melts, acting as an adhesive that enhanced the strength and reduced the thickness of the composite web compared to its state before hot-pressing. Mechanical and physical properties of composite webs were evaluated. Composite webs created from kapok fiber displayed a creamy yellowish-white color, while those made from cattail fiber showed a yellowish-brown color. Composite webs exhibit hydrophobic properties when adding the natural fiber. The maximum natural fiber content, at a ratio of 30, can be incorporated into composite webs while preserving mechanical properties and proper water vapor permeability. This nonwoven material presents an alternative with the potential to replace petroleum-based surgical gowns.

Carbon fibers (CFs) cannot be directly used for the preparation of CF paper because of their chemically inert nature. Herein, the surface of CF was modified via the spontaneous oxidative self-polymerization of dopamine. By taking full advantage of the spontaneous oxidation and self-polymerization properties of PD to maintain the maximum strength of CFs, a polydopamine-modified CF paper (PDA-CFP) with excellent performance was prepared using PD-modified CFs (PDA-CFs), which increased the proportion of hydrophilic functional groups on the surface of carbon fibers, increased the O/C ratio on the CF surface by 6 times, and improved the bond strength between the modified CF and the adhesive by making full use of the interaction force between polydopamine and PVA fibers. In this way, the primary properties of the CF paper was improved. Overall, the results showed that the dispersion of CF was considerably improved by the dopamine modification. In addition, the primary physical properties of PDA-CFP were better than those of virgin CF paper (CFP-0). PDA-CFP exhibited a maximum tensile strength of 2.04 kN/m2, a minimum resistivity of 0.06055 Ω·cm and a minimum porosity of 72.4%. The tightness could be increased by up to 12.1%.

The use of interleaving material with viscoelastic properties is one of the most effective solutions to improve the damping capacity of CFRP laminates. Improving composite damping without threatening mechanical performance is challenging and the use of nanomaterials should lead to the target. In this paper, the effect of a nanostructured interlayer based on Graphite Nanoplatelets (GNPs) on the damping capacity and fracture toughness of CFRP laminates has been investigated. High-content GNP/Epoxy (70wt/30wt) coating was sprayed on the surface of CF/Epoxy prepregs at two different areal weight (10 and 40 g/m2) and incorporated at the middle-plane of a CFRP laminate. The effect of the GNP areal weight on viscoelastic and the mechanical behaviour of the laminates was investigated. Coupons with low-areal weight GNP interlayer showed a 25% increase in damping capacity with a trivial reduction of the elastic modulus. Moreover, a reduction in interlaminar shear strength (ILSS) and fracture toughness (both mode I and mode II) was observed in the composites with GNPs interlayer. GNPs alignment and degree of compaction reached during process were found as key parameters on material performances. By increasing the areal weight a mitigation on the mechanical performances drop was achieved (-15%).

As environmental regulations become stricter, weight- and cost-effective fiber-reinforced polymer com-posites are being considered as alternative materials in the automobile industry. Rapid impregnation of the resin into the reinforcing fibers is critical during liquid composite molding, and the optimization of resin impregnation is related to the cycle time and quality of the products. In this review, various resins capable of rapid impregnation, including thermoset and thermoplastic resins, are discussed for manu-facturing fiber-reinforced composites used in the automobile industry, along with their advantages and disadvantages. Finally, vital factors and perspectives for developing rapidly impregnated resin-based fiber-reinforced composites for automobile applications are discussed

The use of tungsten fiber-reinforced tungsten composites (Wf/W) has been demonstrated to significantly enhance the mechanical properties of tungsten (W) by incorporating W-fibers into the W-matrix. However, prior research has been restricted by the usage of single fiber-based textile fabrics, consisting of 150 µm warp and 50 µm weft filaments, with limited homogeneity, reproducibility, and mechanical properties in bulk structures due to the rigidity of the 150 µm fibers. To overcome this limitation, two novel textile preforms were developed utilizing radial braided yarns with 7 core- and 16 sleeve filaments (R.B. 16+7) as the warp material. In this study, bulk composites of two different fabric types were produced via a layer-by-layer CVD-process, utilizing single 50 µm filaments (type 1) and R.B. 16+7 yarns (type 2) as weft materials. The produced composites were sectioned into KLST-type specimen based on DIN EN ISO 179-1:2000 using electrical discharge machining (EDM), and subjected to three-point bending tests. Both composites demonstrated enhanced mechanical properties with pseudo-ductile behavior at room temperature and endured over 10,000 load cycles between 50-90 % of their respective maximum load without sample fracture. Composites based on fabric type 1 demonstrated superior manufacturing performance and mechanical properties, a high relative average density (>97 %), and high fiber volume fraction (14-17 %). Furthermore, a novel approach to predict the fatigue behavior of the material under cyclic loading was developed based on the high reproducibility of the mechanical properties of type 1, providing a new benchmark for upscaling endeavors.

The effect of the addition of maleated polyethylene (MAPE) to compounds of natural rubber (NR) and Teline monspessulana flour (TMF) previously mercerized was investigated. Two factors were analyzed: A. concentration of MAPE with five levels 2; 4; 6; 8; 10 phr (parts per hundred rubber), B. concentration of TMF with two levels 25 and 40 phr. The effect of MAPE on compatibility between NR and HTM was evaluated by tensile testing the compounds. The mixing was performed in a laboratory scale mill. The test tubes were obtained by cutting or die-cutting crosslinked peroxide sheets, these were obtained during the compression molding process. Analysis indicate that the MAPE coupling agent improved the compatibility between HTM and NR, this effect was evidenced by the values of tensile strength and elongation at break. However, the gel content determination indicates that the addition of 10 phr of MAPE crosslinking decreases due to competition with coupling reaction MAPE - HTM.

Solid-state batteries (SSBs) have emerged as a promising alternative to conventional lithium-ion batteries, with notable advantages in safety, energy density, and longevity, yet the environmental implications of their lifecycle, from manufacturing to disposal, remain a critical concern. This review paper examines the environmental impacts associated with the production, use, and end-of-life management of SSBs, starting with the extraction and processing of raw materials which highlights significant natural resource consumption, energy use, and emissions. A comparative analysis with traditional battery manufacturing underscores the environmental hazards of novel materials specific to SSBs. The review also assesses the operational environmental impact of SSBs by evaluating their energy efficiency and carbon footprint in comparison to conventional batteries, followed by an exploration of end-of-life challenges including disposal risks, regulatory frameworks, and the shortcomings of existing waste management practices. A significant focus is placed on recycling and reuse strategies, reviewing current methodologies like mechanical, pyrometallurgical, and hydrometallurgical processes, along with emerging technologies that aim to overcome recycling barriers, while also analyzing the economic and technological challenges of these processes. Additionally, real-world case studies are presented, serving as benchmarks for best practices and highlighting lessons learned in the field. In conclusion, the paper identifies research gaps and future directions for reducing the environmental footprint of SSBs, underscoring the need for interdisciplinary collaboration to advance sustainable SSB technologies and contribute to balancing technological advancements with environmental stewardship, thereby supporting the transition to a more sustainable energy future.

This study, conducted with meticulous attention to detail, comprehensively examines the state of plants and their adaptation to Kazakhstan's extra-arid climatic zone of the Mangistau. It uses the collections of woody plants from the Mangyshlak Experimental Botanical Garden in Aktau as a case study and extrapolates the results to the entire region. The study area is arid and unsuitable for many plants, so examining physiological adaptation mechanisms and strategies for preserving plants in unfavourable conditions is crucial. The study employed a range of methods, including the measurement of the intensity of transpiration, leaf hydration, and the content of chlorophyll A, B, and carotenoids. These methods were chosen for their proven effectiveness in similar studies and their ability to provide accurate and reliable data. The samples were also assessed using a point system for resistance to drought, phytophagy, gas tolerance, salt tolerance, winter hardiness, and soil fertility. The results obtained and entered into the IEBG platform “DinTseR” to assess the value of the introduction using a diagnostic scale revealed a high variability (up to 51.7-52.2%) of physiological indicators of growth and development. The highest values of transpiration intensity were observed in deciduous trees and shrubs, rose varieties (205-243 mg/g fresh leaf mass per hour), leaf water content - in climbing plants (68.9%), chlorophyll A and B content - in deciduous plants, and plants - old trees, fruit trees and varietal roses (3.46-3.93 and 1.34-1.84%). Their concentration in coniferous species is almost two times lower (0.63%). A correlation was also made between various significant factors. Twenty regression equations and forecasts have been identified that can be used to diagnose and assess resistance, thereby reducing the cost of determining the introduction value in the conditions of Mangistau. These findings are essential in understanding and preserving the unique flora of the Mangistau region.

This article presents the analysis of the allocation of important plant areas (IPA), which urgently identifies the most valuable sites for protecting plant objects. The study is based on a comprehensive inventory of the species composition of plants in the flora of the Western Karatau Ridge and the Mangyshlak Peninsula (arid regions)- key sites Akmysh, Samal, and Kogez, considered standard and the best preserved with natural vegetation cover. The flora of these critical sites was analysed using a combination of field surveys, herbarium studies, and a literature review. The results revealed a rich biodiversity, with 104 species from 82 genera and 33 families. Most species belong to 9 families, making up 60.6% of the total taxa. By the nature of life forms, perennial herbaceous plants dominate in all key sites (30 species, 50.0%). The eco-phylogenetic spectrum showed that a significant share of the flora of the studied IPAs is made up of xerophytes (21 species, 35%) and xeromesophytes (9 species, 15%); desert and mountain-steppe species prevail (53.0%). Rare, endangered and Red Book species account for 10-21.3% of those growing in the region. Regarding economic value, fodder, ornamental, honey, medicinal and food species dominate. The Shannon, Simpson, and Jaccard indices assessed alpha-beta and gamma diversity. The index showed that biodiversity in the Samal and Kogez sites is higher and more evenly distributed compared to the Akmysh site. The Whittaker, Harrison and Cody indices confirm significant differences in the species composition between the sites. In light of these compelling results, a clear and urgent call to action is proposed to allocate these areas to the IPA category, a crucial step towards ensuring the long-term existence of natural biocenoses.

Soil extracellular enzyme activity (EEAs) and enzymatic stoichiometry (ES) can provide a crucial indication of changes in soil ecosystem's nutrient availability and the microbial resource limitations. However, the changing characteristics of soil EEAs and ES at different stages of the native succession process and their key drivers are unclear. In order to investigate the soil EEAs, ES and driving factors of soil under vegetation at different succession stages, we adopted the "spatio-temporal substitution" method to collect the surface soil of bryophyte community, herbaceous community, shrub community and tree community in the new volcanic lava platform of Wudalianchi Volcanic Nature Reserve. We measured seven soil EEA, including carbon(C)-acquiring enzyme (β-1,4-glucosidase (BG)), N-acquiring enzymes (β-N-acetyl-glucosaminidase (NAG) and leucine aminopeptidase (LAP)) and phosphorus (P)-acquiring enzyme (acid phosphatase (AP)) activities. The length and angle of vectors defined by ratios of enzyme activities (BG/(NAG + LAP) vs. BG/AP) were used to indicate relative microbial investments in C- (length), and N- and P- (angle) acquiring enzymes. Our results showed that the contents of TC, TN, TP, MBC, DOC and NO3-N in shrub community soil were significantly higher than those in bryophyte, herb and tree communities, and increased by 441%, 246%, 137%, 5570%, 12% and 484%, respectively. The highest soil EEA of C-, N- and P-acquiring were found in shrub community, and the soil EEAs/MBC of C-, N- and P-acquiring were the highest in bryophyte community. Enzyme C:N, C:P and N:P ratios increased progressively in the order of bryophyte, herb and shrub community, but the enzyme C:N, C:P and N:P ratios of tree community were both far less than shrub community. Vector lengths increased progressively in the order of bryophyte (1.16), herb (1.27), tree (1.29) and shrub (1.40), and Vector angles decreased progressively in the order of bryophyte (49.15°), herb (45.65°), Tree (45.31°) and shurb (44.54°), suggested that as succession progresses, soil microbial nutrients transforms from P limitation (angle＞45°) to N limitation (angle＜45°). Redundancy analysis showed that TC, TN, EC and C:N were important drivers of variation in soil EEAs and ES in vegetation at different succession stages. Our findings highlight that the primary succession process cause nutrient limitation transformation. Soil ES might be a sensitive indicator mediated by soil microorganisms to the relative resource limitation at different stages of the primary succession process.

In this article, we describe a simple procedure for evaluating the sterility of nutrient media using a shear-horizontal surface acoustic wave (SH-SAW) biosensor. We used the SH-SAW biosensor platform to monitor the time-dependent phase responses of the material for the media that binds to a monolayer of 3-mercaptopropanyl-N-hydroxy succinimide on the biosensor surface. Increases in the phase shift less than 50% of the starting phase shift recorded 180 minutes after the sterilization indicate a successful sterility test of the media. Our devices were then applied to sterility testing using a viable Escherichia coli (E. coli) K-12 solution to confirm our hypothesis. Filtered LB Broth was the negative control, and a 24-hour culture of E. coli was the positive control. Before testing, the cell solution was pelleted, the media decanted and then replaced with a 1x phosphate-buffered saline solution (1x PBS). Since we know that the N-hydroxysuccinimide residues will bind to amine groups, only in cases where microbial species are present will the surface binding increase greater than 50%. We confirmed our hypothesis using SH-SAW biosensors and overnight E. coli cultures. The sensitivity for our 250 MHz quartz SH-SAW sensors was calculated based on the response from the E. coli K-12 solution over the linear dynamic range, which appears to be 2x104 – 2x107 CFU per ml and has a sensitivity of S = 1.655x105 o m2 Kg-1. The limit of detection (LOD) for these sensors was calculated to be approximately 2x10-9 grams (g) which is estimated to be approximately 2,000 Escherichia coli (E. coli) K-12 cells. However, the sensitivity and insertion loss remained approximately unchanged before and after coating the sensor with 3,3'-Dithiobis(succinimidyl) Propionate (DSP).

Due to the demands of personal travels and entertainments, light airplanes and small business aircrafts are developing rapidly. Light airplane structure is simple; however, it lacks crashworthiness design, especially the considerations on the impact of energy absorption. Therefore, in an event of accident, significant damage to passengers will be usually incurred. Airplanes made of composite materials structurally have high specific strength and good aerodynamic configuration. These materials have become the primary choice for new airplane development. This study mainly explores the topology optimization analysis of the light aircraft’s cockpit made of carbon fiber reinforced composites. This paper compares the compression amounts in the original models of composite material and aluminum alloy fuselages with the models after optimization during the crash-landing, in order to investigate the safety of fuselages made of different materials after structural optimization under the dynamic crashing. This study found that the energy absorbed by the aluminum alloy fuselage during crash-landing is still higher than that by the carbon fiber reinforced composites fuselage. On the other hand, the aluminum alloy fuselage after topology optimization could have an energy absorption capability enhanced by 40%, as compared to the that of the original model of aluminum alloy fuselage.

Maize is the staple cereal in Malawi, with a daily per capita consumption of 383g (dry matter basis), primarily consumed as dehulled maize flour used to cook nsima, a thick porridge. However, the extent of mass and nutrient loss during dehulling remains unclear in this food-insecure country, where the household maize harvest typically lasts only 6–7 months. In the current study, a milling experiment to determine yield and micronutrient losses was conducted. Milling batches (30 kg) of four maize grain varieties were dehulled at three abrasive disk dehullers under controlled conditions. Mass losses ranged from 18.8% to 42.7%, with a mean of 28.2±5.7%. Maize variety and dehuller significantly affected mass loss (p<0.05). Initial protein, iron, and zinc concentrations were 8.8 ±1.0 g/100g, 20.5±2.0 µg/g, and 18.2 ±2.6 µg/g, respectively. Post-dehulling nutrient true retention varied for protein (49.7% to 75.6%, mean=64.7±7.0%), iron (18.7% to 71.6%, mean=37.6±12.0 %), and zinc (11.0% to 46.2%, mean=27.9±8.7 %). Maize variety significantly influenced mass and protein loss (p < 0.05), while dehuller influenced mass, iron, and zinc losses. However, no significant difference (p > 0.05) was found in the interaction between dehullers and variety on mass and nutrient losses, respectively. Given Malawi's precarious food insecurity situation, transitioning from dehulled maize flour nsima to whole maize flour or less refined nsima, is imperative. Our study findings can have food and nutritional savings for other southern Africa countries where the dehulling practice is rampant.

As part of the efforts to reduce the environmental impacts caused by the aviation sector, the use of bio-based instead of fossil-based materials has been assessed as a possible mitigation option. Natural Fibre Polymer Composites have proven to have a higher environmental performance in the automotive sector and are emerging as an option for weight reduction in aircraft. This study quantifies, though Life Cycle Assessment, the environmental performance of specific flax-based composite panels intended for aircrafts as interior fitting elements (i.e. partition panels, tray tables, baggage compartments) compared to a glass fibre/epoxy composite with a honeycomb core. Through system expansion, the fate of co-products issued from the production of the flax fibre technical textile used as reinforcement in the biocomposite material were considered in the assessment. Results showed that for an application in the aeronautics sector, the weight of the panels is the upmost critical parameter shaping the overall environmental performance of panels. Focusing on the panel production only, the biocomposite panel showed a higher environmental performance in the categories of climate change and marine eutrophication compared to the conventional panel, and the fire suppressant agent was identified as the main contributor to the environmental impacts of the bio-based panel. Yet these gains were negligible when considering the full life cycle of the panels, due to the higher weight (14%) of the bio-based panels; which is linked to the bio-based panel being at a prototype stage.In order to improve the environmental performance of the biocomposite panel and thus reduce its weight, it was shown relevant to optimize geometry of the panel itself, especially its core, so less resin could be used.

Grain quality, cooking quality and nutritional quality traits are some of the major attributes that enhance uptake and utilisation of improved cowpea varieties. Therefore, there is need for a better understanding of the genetic variation and inter-relationships among these quality traits in cowpea to integrate them in cowpea breeding programs. The study was conducted to determine genetic variability among 306 cowpea genotypes for grain quality, cooking quality and nutritional quality traits and to understand the interrelationships among these traits for exploitation in breeding programs. The results showed highly significant differences (P

Glass fibers slowly dissolve and age when exposed to water molecules. Such a phenomenon also occurs when glass fibers are inside fiber-reinforced composites protected by the matrix. This en-vironmental aging results in the deterioration of the mechanical properties of the composite. In structural applications, GFRPs are continuously exposed to water environments for decades (typically design lifetime is around 25 years or even more). During their lifetime, these materials are affected by various temperatures, pH acidity levels, mechanical loads, and the synergy of these factors. The rate of the degradation process depends on the nature of glass, sizing, fiber orientation, and environmental factors such as acidity, temperature, and mechanical stress. In this work, degradation of typical industrial grade R-glass fibers, when inside an epoxy fiber-reinforced composite, is studied experimentally and computationally. A Dissolving Cylinder Zero-Order Kinetic (DCZOK) model was applied and could describe the long-term dissolution of glass composites, considering the influence of fiber orientation (hoop vs transverse), pH (1.7, 4.0, 5.7, 7.0, and 10.0), and temperature (20, 40, 60, and 80 °C). The limitations of the DCZOK model and effects of sizing protection, accumulation of degradation products inside the composite, and water availability were discussed. Experimentally dissolution was measured using ICP-MS. Like for the fibers, for GFRPs also, the temperature showed an Arrhenius-type influence on the ki-netics, increasing the rate of dissolution exponentially with increasing temperature. Similar to fibers, GFRPs showed a hyperbolic dependence on pH. The model was able to capture all of these effects, and the limitations were addressed.

The formation of a rigid tough interface based on a nacre-like structure in carbon fiber (CF) composites is a promising way to eliminate low delamination resistance. An effective method of coating CFs is electrophoretic deposition (EPD), which, in the case of dissimilar components like graphene oxide (GO) and polymeric glue, usually requires their chemical bonding/ strong interactions. In this work, we focus on chitin nanocrystals (ChNCs), leading to an excellent mechanical performance of artificial nacre, where favorable interactions and bonding with GO were controlled by degrees of deacetylation (5, 15 and 30 %). We have prepared coatings based on GO/ChNCs adducts with 95/5, 90/10,50/50 and 25/75 ratios using optimized EPD conditions (pH, concentration, voltage and time). The prepared materials were characterized using FTIR, TEM, XPS, SEM, DLS, and XRD. SEM evaluation indicates the formation of a homogeneous interlayer, which possesses a fair ability of chemical bonding with the epoxy matrix. Short beam testing of epoxy matrix composites indicates that coating does not decrease stiffness and its relatively low dependence on composition. Therefore, all coatings are promising for a detailed study of delamination resistance using laminate samples. Moreover, facile EPD from water solution/ suspension has a fair potential for industrial applications.

In this study, a novel task of printing speed optimization for continuous fiber composites is investigated. Using continuous fibers is an innovative approach to reinforce products made by fused filament fabrication (FFF) additive manufacturing (AM) technology. In the printing process of composites with continuous fibers, the printing speed is critical because of its significant effect on the geometric shape of the samples, especially their corners. During optimization in this research, continuous glass fiber (CGF) and polylactic acid (PLA) filaments were utilized as reinforcing phase and matrix, respectively, and were simultaneously fed into the extrusion-based polymer 3D printer to form PLA/CGF composites. The optimization was carried out by calculating the temperature changes of the deposited rasters in the presence and absence of fibers as a first step and then determining the special relationship between the printing speeds and rasters temperature changes. Finally, the optimal and the maximum printing speed was computed based on a hypothesis, which is proved by the results of high-quality printed composites with different geometric shapes.

Viral contamination in the aquaculture industry is a significant challenge that requires further research. Emerging evidence suggests that long noncoding RNAs (lncRNAs) play a role in regulating various biological processes, including immunity. However, most studies have focused on model organisms, and little is known about non-coding RNAs in the immune response to viral hemorrhagic septicemia (VHS) in rainbow trout. In this study, we investigated the listing of non-coding RNAs (ncRNAs) in rainbow trout challenged with VHS virus. We explored their potential role in defense-like responses based on transcriptomic analysis of the virus-treated and control groups. As a result of this research, 4207 lncRNAs were identified, of which 182 lncRNAs were differentially expressed between treated and untreated samples. Among 7753 lncRNA transcripts, 1920 were novel intergenic (class code “u”), and 3748 transcripts were potentially novel isoform of lncRNAs. Gene ontology analysis revealed biological pathways associated with the stress response and immune signaling. Pairs of genes such as TP63-MSTRG.62, IL10-MSTRG.9783, IL10-MSTRG.9784, TK1-MSTRG.22826, and MSTRG.17881-GLI1 showed cis interactions, while DOCK10-MSTRG.30015, MSTRG.36357-LOC101268921, and MSTRG.34190-ENPP2 showed trans interactions. In this study, the role of lncRNAs in regulating the expression of the target genes was clearly identified. This finding is consistent with the regulatory processes of immune system responses mediated by cytokines, as well as the regulation of oxygen levels in response to viral infection. The information presented here highlights the various regulatory mechanisms of lncRNAs in the expression of immune system genes in fish treated with VHS virus.

In magneto-photoluminescence (magneto-PL) spectra of quasi-two dimensional islands (quantum dots) having seven electrons and Wigner-Seitz radius rs~1.5, we revealed a suppression of magnetic field (B) dispersion, paramagnetic shifts and jumps of the energy of the emission components for filling factors >1 (B<10 T). Additionally, we observed B-hysteresis of the jumps and a dependence of all these anomalous features on rs. Using a theoretical description of the magneto-PL spectra and an analysis of the electronic structure of these dots based on the single-particle Fock-Darwin spectrum and many-particle configuration-interaction calculations, we show that these observations can be described by the rs-dependent formation of the anyon (magneto-electron) composites (ACs) involving single-particle states having non-zero angular momentum and that the anyon states observed involve Majorana modes (MMs), including zero-B modes having equal number of vortexes and anti-vortexes, which can be considered as Majorana anyons. We show that the paramagnetic shift corresponds to a destruction of the equilibrium self-formed ~5/2 AC by the external magnetic field and that the jumps and their hysteresis can be described in terms of Majorana qubit states controlled by B and rs. Our results show a critical role of quantum confinement in the formation of magneto-electrons and implies the liquid-crystal nature of fractional quantum Hall effect states, Majorana anyon origin of the states having even , i.e., composite fermions, which provide new opportunities for topological quantum computing.

Mass hauling operations play central roles in construction projects. They typically use many haulers that consume large amounts of energy and emit significant quantities of CO₂. However, practical methods for estimating the energy consumption and CO₂ emissions of such operations during project planning are lacking. This paper presents a detailed model for estimating the energy consumption and CO₂ emissions of mass haulers that integrates the mass hauling plan with a set of predictive equations. The mass hauling plan is generated using a planning program such as DynaRoad in conjunction with data on the productivity of selected haulers and the amount of material to be hauled during cutting, filling, borrowing, and disposal operations. This plan is then used as input for estimating the energy consumption and CO₂ emissions of the selected hauling fleet. The proposed model will help planners to assess the energy and environmental performance of mass hauling plans, and to select hauler and fleet configurations that will minimize these quantities. The model was applied in a case study, demonstrating that it can reliably predict energy consumption, CO₂ emissions, and hauler productivity as functions of the hauling distance for individual haulers and entire hauling fleets.

Crops obtained by genome editing (GE) technologies represent a notable and disruptive shift from genetically modified or transgenic plants, outpacing public perception and regulatory frame-works. Multiple aspects of GE are contributing to the advancement of modern agriculture, in-fluencing the market structure by introducing specific changes within the existing genetic blue-print of an organism. Generally, the GE toolbox includes distinct technologies able to incorporate site-specific and pre-determined genomic modifications, exploiting well-established genetic modification strategies. For these reasons, GE-derived approaches are considered new plant breeding methods, known as new breeding techniques (NBTs). Particularly, CRISPR/Cas-based technologies represent a considerable improvement over prior techniques, being more precise, accurate and straightforward for targeted gene editing, in a reliable and reproducible way, with numerous applications. CRISPR/Cas system exploitation for non-editing purposes has also been widely documented, ranging from cell imaging to expression regulation and DNA assembly. Recently, CRISPR/Cas systems have been employed for target detection and could be used to ef-ficiently identify multiple organic chemicals. High-sensitivity and high-specificity detection are two main points of the CRISPR/Cas technology, without needing complex expertise or technical pipelines. This manuscript aims to provide an overview of the main advances of CRISPR/Cas-based systems into new frontiers of non-editing. The associated implications (e.g., molecular traceability) and their relative impacts are also presented and discussed.

In this research, a screw-barrel system was designed and implemented, coupled with material extrusion, to print high-melt-temperature thermoplastic materials. The aim was to integrate two methods: the direct extrusion of thermoplastic polymer pellets with material extrusion,utilize various polymers in the form of pellets, especially high melt temperature ones, instead of traditional filaments. This addresses one of the significant challenges in filament preparation for various materials that are not readily available in the market or nearly impossible to fabricate (such as highly filled plastics). First, the screw-barrel assembly performance and factors influencing feed rate were evaluated. Subsequently, specimens were printed with polyether ether ketone (PEEK), an advanced plastic material known for its outstanding mechanical properties, high-temperature tolerance, and broad applications in various sectors, such as medical. Additionally, the material was reinforced with 2.5% continuous glass fibers while printing, which presented a novel product. Upon comparing theoretical values with experimental data from the tensile testing, a notable observation emerged: the inclusion of 2.5% glass fibers led to an approximate 43% increase in the tensile strength of the material. Furthermore, SEM images provided visual evidence of satisfactory adhesion between layers and fibers.

Defectively manufactured and deliberately damaged composite laminates fabricated with different continuous reinforcing fibres (respectively, carbon and glass) and polymer matrices (respectively, thermoset and thermoplastic) were inspected in magnetic resonance imaging equipment. Two pulse sequences were evaluated during non-destructive examination conducted in saline solution-immersed samples to simulate load-bearing orthopaedic implants permanently in contact with biofluids. The orientation, positioning, shape, and especially the size of translaminar and delamination fractures were determined according to stringent structural assessment criteria. The spatial distribution, shape, and contours of water-filled voids were sufficiently delineated to infer the amount of absorbed water if thinner image slices than this study were used. The surface texture of composite specimens featuring roughness, waviness, indentation, crushing, and scratches was outlined, with fortuitous artefacts not impairing the image quality and interpretation. Low electromagnetic shielding glass fibres delivered the highest, while electrically conductive carbon fibres produced the poorest quality images, particularly when blended with thermoplastic polymer, though reliable image interpretation was still attainable.

As the world population grows, fulfilling the need for biomaterials in the healthcare system becomes increasingly important. Biomaterials, which include metals, polymers, ceramics, and composites, play an important role in the creation of medical devices that improve people's lives. The European Society for Biomaterials described biomaterials as non-biological materials used in medical devices to interact with biological systems. This definition has developed to encompass materials that treat, assess, or replace tissues or bodily functions. Biocompatibility, as defined by the FDA, is a key feature of biomaterials, as is the requirement to fulfil design requirements such as mechanical performance, geometry, and electrical control. Over the last decade, advances in regenerative medicine and tissue engineering have boosted biomaterials' usage in medical applications dramatically. Despite its promise, scientists, engineers, and physicians continue to face significant challenges due to the complexity of biomaterials. Biomaterials have various benefits, including biodegradability, non-toxicity, and biocompatibility, making them extremely useful for replacing, sustaining, or improving biological activities in damaged tissues. They are used in a wide range of applications, including tissue engineering implants, human tissue healing and regeneration, medication delivery systems, and biosensors. This study gives insights into the fundamental characteristics, case studies, and ethical issues associated with the usage and use of biomaterials, further examining their potential and significance in healthcare and medicine.

Thermal camouflage is a highly sought-after technology to increase the survivability of military equipment against infrared (IR) detectors. Recently, two-dimensional (2D) nanomaterials have shown low IR emissivity, widely tunable opto-electronic properties and compatibility with stealth-applications. Among them, graphene and graphene-like materials are the most attractive 2D materials used for thermal camouflage applications. In particular, in multilayer graphene (MLG) charge density can be effectively tuned through sufficiently intense electric fields or through electrolytic gating. Therefore, MLG optical properties, like infrared emissivity and absorbance, can be controlled in a wide range by voltage bias. The large emissivity modulation achievable with this material makes it suitable in the design of thermal dynamic camouflage devices. Generally, the emissivity modulation in the multilayered graphene medium is governed by an intercalation process of non-volatile ionic liquids under a voltage bias. The electrically-driven reduction of emissivity leads to a decrease in the apparent temperature of the surface, which can match that of the background enabling thermal camouflaging. Since this property is common to other graphene-based materials, here we present a review specifically focused on the recent advances in the field of the thermal camouflage properties of graphene in the form of composite film and aerogel structures. A summary of the current understanding of the working principle of thermal camouflage materials, current limitations, and future opportunities is presented and discussed.

This paper aims to build up a preference function to evaluate the public benefits of the type of agricultural farming, biodiversity, water provisions, land use type, ecotourism modes, and a monetary attribute (environmental trust fund and willingness to contribute) associated with an ecosystem service and land use program in a forest park. This study used the choice experiments to build a random utility model, analyze the average preference for the above land use attributes based on the conditional logit and used a latent class model to test the resident’s heterogeneous preferences for land use planning in the forest park. We also estimated the welfare derived from various land use programs. The empirical result had shown that: (1) increasing organic farming area, maintaining the status quo of species biodiversity, increasing the surface water provision, increasing the area of custom flora, increasing the wetland area, and setting up an integrated framework for ecotourism increase the public’s preference for the land use program; (2) we found that farmer and non-farmer haven’t the same land use preferences; (3) the ecotourism development program incorporating biodiversity, organic farming, ethnobotany, and wetland area with integrated ecotourism are more preferred than other land use program scenarios.

Reactions of quinones with compounds containing an amino group can produce a wide variety of addition or substitution products that depend on reactivity of both quinone and amino derivative. 6,7-Dichloropyrido[1,2-a]benzimidazole-8,9-diones undergo selective nucleophilic substitution reaction with different benzohydrazides and α-hydroxy-p-quinone imine derivatives stabilized by strong intramolecular hydrogen bond were isolated. Synthesized compounds represent a combination of several structural motifs: benzimidazole core fused with α-hydroxy-p-quinone imine which contains a benzamido fragment. The protonation/deprotonation processes were investigated in a solution using UV-Vis spectroscopy and 1H NMR titration experiment. X-ray crystallography analysis revealed a set of weak non-covalent interactions such as intra- and intermolecular hydrogen bonds and π-π stacking. Additionally, the redox behavior of 6,7-dichloropyrido[1,2-a]benzimidazole-8,9-dione and its p-imino derivative was investigated in acidic and neutral environment using cyclic voltammetry measurements. Cathode material based on 6,7-dichloropyrido[1,2-a]benzimidazole-8,9-dione could act as potential effective active electrode in aqueous electrolyte batteries, however further optimization is required.

Natural fibers are a gift from nature that we yet fully utilized until now. It can be classified into several groups and bast fibers are the group having the most promising performance when reinforced in polymer composites. However, numerous factors have been reported that influences mechanical properties of fiber reinforcements in the composite. In this review, bast fiber retting process and the effect of enzymatic retting on fiber and fibers reinforced polymer composites have been discussed and reviewed for the latest researches. Retting precedes mechanical processing (i.e. scutching) of the fiber from the stem and is essential for reduction of fiber breakage. All retting methods except chemical retting process are involving secretes of enzymes by bacteria or fungi under controlled (enzymatic retting) or random conditions (water and dew retting). Besides, enzymatic retting is claimed to have more environmentally friendly wastewater products, shorter retting period and controllable fiber biochemical components under mild incubation conditions. This review comprehensively assesses the enzymatic retting process for producing high-quality bast fiber and will become a reference for future development on bast fiber reinforced polymer composites.

Mesenchymal stem cells (MSCs) hold immense therapeutic potential due to their regenerative and immunomodulatory properties. However, to utilize this potential, it is crucial to optimize their in vitro cultivation conditions. Three-dimensional (3D) culture methods using cell-laden hydrogels aim to mimic the physiological microenvironment in vitro, thus preserving MSC biological functionalities. Cellulosic hydrogels are particularly promising due to their biocompatibility, sustainability, and tunability in terms of chemical, morphological, and mechanical properties. This study investigated the impact of (1) two physical crosslinking scenarios for hydrogels derived from anionic cellulose nanofibers (CNF) used to encapsulate adipose-derived MSCs (adMSCs) and (2) physiological culture conditions on the in vitro proliferation, differentiation, and extracellular vesicle (EV) production of these adMSCs. Our results revealed that additional Ca2+-mediated crosslinking, intended to complement self-assembly and gelation of aqueous to-CNF in the adMSC cultivation medium, adversely affected both the mechanical properties of the hydrogel spheres and the growth of the encapsulated cells. However, cultivation under dynamic and hypoxic conditions significantly improved the proliferation and differentiation of the encapsulated adMSCs. Furthermore, we demonstrated that adMSCs in CNF hydrogel spheres exhibited potential for scalable EV production with potent immunosuppressive capacities in a bioreactor system. These findings underscore the importance of physiological culture conditions and the suitability of cellulosic materials for enhancing the therapeutic potential of MSCs. Overall, our study provides valuable insights for optimizing the in vitro cultivation of MSCs for various applications, including tissue engineering, drug testing, and EV-based therapies.

Recently, polyacetylene (PA) is receiving a renewed scientific attention due to its electrical properties potentially useful for energy applications (e.g., fabrication of electrodes for batteries and supercapacitors) and unique functional characteristics (e.g., flame retardant, oxygen scavenger, EMI-shielding, etc.). This chemical compound can be obtained in form of a polyacetylene-PVOH copolymers simply by chemical dehydration of poly(vinyl alcohol) (PVOH), which is a very common type of polymer, widely used in packaging and other technological areas. This very inexpensive chemical reaction for the large-scale synthesis of PA/polyvinylenes has been investigated by reacting PVOH with fuming sulfuric acid at room temperature. In this process, PVOH, shaped in form of film, is dipped in fuming sulfuric acid (i.e., H₂SO₄ at 95-97%) and, after complete chemical-dehydration, it has been mechanically removed from the liquid phase by using a nylon sieve. The reduction process leads to a substantial PVOH film conversion to PA as it has been proved by infrared spectroscopy (ATR-mode). Indeed, the ATR spectrum of the reaction product included all characteristic absorption bands of PA. The reaction product has been also characterized by UV-Vis spectroscopy in order to evidence the presence in the structure of conjugated carbon-carbon double bonds of various lengths. Differential scanning calorimetry (DSC) and thermogravimetric analysis have been used respectively to investigate the PA solid-state cis-trans isomerization and thermal stability in air and nitrogen, respectively.

Polyalcohol liquefaction can be done by acid or basic catalysis producing polyols with different properties. This study compared the mechanical properties of foams produced using polyols from liquefied Cytisus scoparius obtained by acid and basic catalysis and using two different foam catalysts. The differences were monitored using FTIR analysis. Acid-catalyzed liquefaction yielded 95.1 %, with the resultant polyol having an OH index of 1081 mg KOH/g while basic catalysis yielded 82.5 %, with a similar OH index of 1070 mg KOH/g. Generally, compressive strength with dibutyltin dilaurate (DBTDL) ranged from 16 - 31 kPa (acid-liquefied polyol) and 12 -21 kPa (base-liquefied polyol), while with stannous octoate (TIN), it ranged from 17 - 42 kPa (acid) and 29 - 68 kPa (base). Increasing water content generally decreased the compressive modulus and strength of foams. Higher water content led to a higher absorption at 1670 cm-1 in the FTIR spectrum due to the formation of urea. Higher isocyanate indices generally improved compressive strength, but high amounts led to unreacted isocyanate that could be seen by a higher absorption at 2265 cm-1 and 3290 cm-1. DBTL was shown to be the best foam catalyst due to higher trimer conversion seen in the spectra by a higher absorption at 1410 cm-1. Acid and base-derived polyols lead to different polyurethane foams with different FTIR spectra, particularly with a higher absorption at 1670 cm-1 for foams from acid-derived liquefaction.

Spray penetration into citrus canopies is critical for adequate coverage and deposition to ensure effective pest control. However, mismatch of air assistance to target canopy characteristics can lead to unintended spray loss through over penetration. To evaluate the effect of air assistance on on-target deposition, two sprayers (surrogates for airflow rates) were used to apply a fluorescent tracer dye solution @ target concentration of 300 ppm to 16 medium foliage density tree blocks in a commercial mandarin orchard. The complete factorial experiment in three replications comprised two ground speeds (1.6 and 4.8 km/h), two disc-core nozzles (TeeJet® D3-25 and D6-45), and either one or two nozzle rows to obtain a wide range of application rates (496 to 9,719 L/ha). Dye deposition significantly decreased with canopy depth (p=<0.001) by nearly 7 times across the 3.4-m-wide canopies but was not significant over 1.2 to 2.2 m sampling height (p=0.867). Deposition obtained with the low airflow rate sprayer was significantly greater (p=<0.001) than that obtained with the high airflow rate sprayer over the dose range likely due to too much air pushing out spray droplets. This study underscores the importance of matching the air assistance of orchard sprayers to the target canopy.

Listeria monocytogenes is an emerging pathogen responsible for the serious foodborne disease, listeriosis. The commensal gut microbiota is the first line of defense against pathogen internalization. The gut microbiome can be modified by prebiotic substrates, which are frequently added to food products and dietary supplements. Prebiotics should selectively support the growth of beneficial microbes and thus improve host health. Nevertheless, little is known about their effect on the growth of L. monocytogenes. The aim of this study was to evaluate the growth ability of four L. monocytogenes strains, representing the most common serotypes, on prebiotic oligosaccharides (beta-(1,3)-D-glucan, inulin, fructooligosaccharides, galactooligosaccharides, lactulose, raffinose, stachyose, and 2´-fucosyllactose and a mixture of human milk oligosaccharides) as a sole carbon source. The results showed that only beta-(1,3)-D-glucan was metabolized by L. monocytogenes. Therefore, the safety of beta-(1,3)-D-glucan with respect to listeriosis development should be further studied.

Current agriculture intensifies crop cultivation to meet food demand, leading to unsustainable use of chemical fertilizers. This study investigates a few physiological and agronomic responses of common wheat following the inoculation with plant growth-promoting bacteria to reduce nitrogen inputs. A field trial was conducted in 2022-23, in Legnago (Verona, Italy) on Triticum aestivum var. LG-Auriga comparing full (180 kg ha-1) and reduced (130 kg ha-1) N doses, both with and without foliar application at end tillering of the N-fixing bacterium Methylobacterium symbioticum. Biofertilization did not improve shoot growth, while it seldom increased root length density in the arable layer. It delayed leaf senescence, prolonged photosynthetic activity, amplified stomatal conductance and PSII efficiency under reduced N dose. Appreciable ACC-deaminase activity of such bacterium disclosed augmented nitrogen retrieval and reduced ethylene production, explaining ameliorated stay-green. Yield and testing weight were unaffected by biofertilization, while both glutenin-to-gliadin and HMW-to-LMW ratios increased together with dough tenacity. It is concluded that Methylobacterium symbioticum can amplify nitrogen metabolism at reduced nitrogen dose, offering a viable approach to reduce chemical fertilization under suboptimal growing conditions for achieving a more sustainable agriculture. Further research over multiple growing seasons and soil types is necessary to corroborate these preliminary observations.

Wood plastic composite usage and demands have increased due to chemical, and mechanical properties when compared to plastic materials. However, because of the possibility of structural and mechanical changes of the material when exposed to external environment more research needs to be done. In the present study yellow birch/HDPE composites materials made by injection molding were treated by zinc oxide and exposed to fungal rots. Mechanical properties of the composites were assessed by Tensile and Izod impact test. The impact energies of the samples loaded with 30 % ZnO-treated fibers and exposed to G. trabeum and T. versicolor decreased, compared to when samples were not treated with ZnO. The mechanical properties of all samples treated with ZnO and exposed to rot decreased which were reported as a decreased Young's modulus and impact energies. ZnO prevented mycelium proliferation which was nonexistent on samples. It has been noted that the decrease in mechanical properties of treated samples was due to NaOH used to dissolve the ZnO powder.

A multiscale modelling approach was developed in order to estimate the effect of defects on the strength of unidirectional carbon fiber composites. The work encompasses a micromechanics approach, where the known reinforcement and matrix properties are experimentally verified and a 3D finite element model is meshed directly from micrographs. Boundary conditions for loading the micromechanical model are derived from macroscale finite element simulations of the component in question. Using a microscale model based on the actual microstructure, material parameters and load case allows realistic estimation of the effect of a defect. The modelling approach was tested with a unidirectional carbon fiber composite beam, from which the micromechanical model was created and experimentally validated. The effect of porosity was simulated using a resin-rich area in the microstructure and the results were compared to experimental work on samples containing pores.

In the recent concrete industry, high fluidity concrete is being widely used for the pouring of dense reinforced concrete. Normally, in the case of high fluidity concrete, it includes high binder contents, so it is necessary to replace part of the cement through admixtures such as fly ash to procure economic feasibility and durability. This study shows the mechanical properties and field applicability of high fluidity concrete that using mass of fly ash as alternative materials of cement. The high fluidity concrete mixed with 50% fly ash was measured to manufacture concrete that applies low water/binder ratio to measure the mechanical characteristics as compressive strength and elastic modulus. Also, in order to evaluate the field applicability, high fluidity concrete containing high volume fly ash was evaluated that fluidity, compressive strength, heat of hydration and drying shrinkage of concrete.

Lactoperoxidase system (LPS) effect on quality of raw and pasteurized milk under real conditions along the dairy value chain in Ethiopia was evaluated. A total of 250 milk samples were collected from farmers, collectors, and factories. Experimental samples were LPS-activated of morning and overnight milk. The samples were tested with several chemical and microbiological tests such as total bacterial count (TBC), total coliform count (TCC) and Escherichia coli count (EC). Results indicated that all LPS-activated milk samples had a higher quality than all the control samples. For instance, both the morning and overnight farm milk samples had a mean TBCs of 5.79 log and 6.55 log cfu/ml which is significantly (p

This paper proposes an innovative approach to address the challenge of softening deformation of thermal-curable thermosets during additive manufacturing. This approach involves the development of a composite powder composed of thermosetting materials with distinct curing temperatures, the utilization of Cold Spray Additive Manufacturing (CSAM) technology for 3D printing, and the application of a stepwise isothermal curing process. The corresponding effectiveness is validated by case studies. The results demonstrate that samples printed via CSAM maintain a solid state without deformation. During the post-curing process, each component of the composite material cures independently while the other components remain in a solid state, providing structural support for the whole material, thereby effectively reducing the softening deformation during the post-curing process. This approach offers a novel perspective for the additive manufacturing of thermal-curable thermosets.

To address the insufficient mechanical properties of calcined phosphogypsum, this research aims to investigate the utilization of basalt fiber and calcium carbonate whiskers as reinforcing agents. The study examines their impact on the flexural and compressive strength, toughness, water resistance, and tensile strength of calcined phosphogypsum. In the individual tests, basalt fibers with different lengths (3 mm, 6 mm, 9 mm, and 18 mm) were added at dosages of 0%, 0.5%, 1.0%, and 1.5% respectively. The findings demonstrate that basalt fiber effectively enhances the flexural and compressive strength, toughness, and tensile strength of calcined phosphogypsum, albeit potentially compromising water resistance. Among the various fiber lengths, the 6 mm fibers exhibit the most advantageous influence on the performance of calcined phosphogypsum. A subsequent test was conducted to investigate the impact of cross-scale fibers on the properties of calcined phosphogypsum by mixing 6 mm basalt fibers and calcium carbonate whiskers. The results illustrate that calcium carbonate whisker refines the pores, thereby improving the flexural strength and toughness of calcined phosphogypsum. Furthermore, it compensates for the water resistance limitations associated with the sole utilization of basalt fiber while further augmenting the tensile strength and strain capacity. However, it should be noted that increasing the dosage of both calcium carbonate whiskers and basalt fibers concurrently leads to increased porosity of phosphogypsum and reduced compressive strength.

Pore structure characterization and fractal analysis have great significance for understanding and evaluating tight limestone reservoirs. In this work, the pore structure of tight limestone is characterized combined with low-temperature nitrogen adsorption (LTNA) and low-field nuclear magnetic resonance (NMR), and the fractal dimension of tight limestone pore structure is discussed based on LTNA and NMR data. The results indicate that the pores of tight limestone have H3 and H4 types, the pore size distribution (PSD) of H3 type is a wave distribution ranging from 2 to 10 nm, and the PSD of H4 type is a unimodal distribution ranging from 2 to 10 nm. The transverse relaxation time (T2) spectrum of tight limestone shows single peak (DF), double peak (SF) and three peak (TF), and the T2 spectrums for micropores, mesopores and macropores range from 0.1 to 10 ms, from 10 to 100 ms, and greater than 100 ms, respectively. The LTNA fractal dimension of tight limestone (DL) ranges between 2.4446 and 2.7688, with an average of 2.5729, and the NMR fractal dimensions of micropores (DNMR1), mesopores (DNMR2) and macropores (DNMR3) are distributed between 0.3744 to 1.1293, 2.4263 to 2.9395 and 2.6582 to 2.9989, respectively. Moreover, there is no correlation between fractal dimension and permeability and porosity, a negative correlation between DL and average pore radius, a positive correlation between DL and specific surface area, and a positive correlation between DNMR2 and DNMR3 and micropore content, while DNMR2 and DNMR3 are negatively correlated with the content of mesopores and macropores.

Porous hierarchical structure has been widely used in engineering for its high specific strength and stiffness, improved corrosion-resistance and multifunctionality. The design of multi-scale topology optimization for such structures has been a hot topic during the past two decades. In this paper, a new hybrid MMC-density topology optimization method of cellular structures with quasi-periodic microstructures is proposed. The so-called ‘quasi-periodic’ means the microstructures in different macro points have similar topology but with different parameters. The key idea is to describe the microstructural topology using MMC and describe the micro layout using the variable density. Sensitivities of the structural compliance with respect to the two types of design variables are derived and gradient optimization method is applied to update the design variables. The presented numerical examples show that the quasi-periodic cellular structures have better performance than single-scale structures and periodic cellular structures. Numerical examples demonstrate the effectiveness of the proposed approach.

Adult neurogenesis involves generation of functional neurons from neural progenitor cells, which have the potential to complement and restore damaged neurons and neural circuits. Therefore, the development of drugs that stimulate neurogenesis represents a promising strategy in stem cell therapy and neural regeneration, greatly facilitating the reconstruction of neural circuits in cases of neurodegeneration and brain injury. Our study reveals that compound A5, previously designed and synthesized by our team, exhibits remarkable neuritogenic activities, effectively inducing neurogenesis in neural stem/progenitor cells (NSPCs). Subsequently, transcriptome analysis using high-throughput Illumina RNA-seq technology was performed to further elucidate the underlying molecular mechanisms by which compound A5 promotes neurogenesis. Notably, comparative transcriptome analysis showed that the up-regulated genes were mainly associated with neurogenesis and the down-regulated genes were mainly concerned with cell cycle progression. Furthermore, we confirmed that compound A5 significantly affected the expression of transcription factors related to neurogenesis and cell cycle regulatory proteins. Collectively, these findings identify a new compound with neurogenic activity and may provide insights into drug discovery for neural repair and regeneration.

The growing interest in benchtop NMR systems is visible in a vast number of applications in science and industry. Low-field nuclear magnetic resonance (LF-NMR) became an instant in technologies that productions are dependent on the reliable structure identification, grade and purity control, chemical process inspection or reaction monitoring. Beyond the benefits of being cost-, space-, maintenance- and user friendly, insufficient sensitivity and low signal resolution are the main drawbacks, due to which the low-field NMR (LF-NMR) in the fields of organic chemistry and synthesis remains limited to solely academic teaching purposes. Herein, we discuss the possibilities of LF-NMR for the needs of organic chemistry and synthesis on a set of compounds 1-4 achieved as the products of student’s laboratory course and organic derivatives 5-8 that are from our research interests. Chemical structure determination of all compounds 1-8 presented herein was performed using the benchtop-type NMR instrument operating at 60 MHz (Pulsar Oxford Ltd.). Structure of novel compounds 5-7 prepared under the aims of our research was characterized by combined 1H/19LF-NMR and compared with an appropriate high-field NMR data from Bruker Ascend Instrument (400 MHz). Finally, possibilities of the low-field NMR as an analytical tool for the research purposes in the fields of organic chemistry and synthesis are documented on a set of 1H and 2D 1H-1H COSY for azomethine 8.

Fire detection from satellite sensors relies on an accurate estimation of the unperturbed state of a target pixel, from which an anomaly can be isolated. Methods for estimating the radiation budget of a pixel without fire depend upon training data derived from the location's recent history of brightness temperature variation over the diurnal cycle, which can be vulnerable to cloud contamination and the effects of weather. This study proposes a new method that utilises the common solar budget found at a given latitude in conjunction with an area's local solar time to aggregate a broad-area training dataset, which can be used to model the expected diurnal temperature cycle of a location. This training data is then used in a temperature fitting process with the measured brightness temperatures in a pixel, and compared to pixel-derived training data and contextual methods of background temperature determination. Results of this study show similar accuracy between clear-sky medium wave infrared upwelling radiation and the diurnal temperature cycle estimation compared to previous methods, with demonstrable improvements in processing time and training data availability. This method can be used in conjunction with brightness temperature thresholds to provide a baseline for upwelling radiation, from which positive thermal anomalies such as fire can be isolated.

(1) Background: A wide literature based on loading and unloading bending tests has been carried out over the half past century for assessing the force released by superelastic wires. The aim of this investigation is not only to characterize a broadly described superelastic NiTi and a novel CuNiTi archwire, but also to provide novel insights into the load vs deflection profiles. A harmonic scenario for superelastic wires will be shown as temperature is kept constant at 37°C. However, a completely different picture will be highlighted as a temporary heating step up to 50°C is introduced within the force vs deflection profiles. (2) Methods: A variety of NiTi and a novel CuNiTi round and rectangular cross-section archwires have been investigated. Static 3-point bending tests up to a deflection level of 3.0 mm have been carried out for detecting the unloading force plateau levels occurring at 37°C. A hold deflection step of 5 min at deflection levels occurring along the unloading plateau extension is introduced. The effect of a temporary heating up to 50°C on the force plateau level released by the investigated wires is analyzed. (3) Results: Mechanical profiles suggest that the plateau force levels detected at 37°C are consistent with those broadly reported in the literature, but they only represent a single block puzzle of the force scenario that a superelastic wire releases during the orthodontic treatment. (4) Conclusions: Once a superelastic wire is bent and clinically applied, the effect of a temporary heating up to 50°C (e.g. hot food or drink ingestion) produces a significant plateau force increase whose magnitude depends on the deflection level. The highest force increase of about 50% and 40% have been detected at deflection levels located at the beginning of the unloading plateau extension for NiTi and CuNiTi wires, respectively.

A novel Gram-stain-negative, facultatively anaerobic and mixotrophic bacterium, designated as strain LZ166T, was isolated from the bathyplagic seawater in the western Pacific Ocean. Cells were short rod-shaped, oxidase- and catalase- positive, and motile by means of lateral flagella. Growth of strain LZ166T was observed at 10-45 ℃ (optimum, 34-37 ℃), at pH 5-10 (optimum, 6-8) and in the presence of 0-5% NaCl (optimum, 1-3%). Phylogenetic analysis based on the 16S rRNA gene showed that strain LZ166T shared the highest similarity (98.58%) with Aquibium oceanicum B7T, and formed a distinct branch within the Aquibium genus. Genomic characterization, including average nucleotide identity (ANI, 90.73-76.79%), average amino identity (AAI, 88.50-79.03%) and digital DNA-DNA hybridization (dDDH, 36.1-22.2%) values between LZ166T and other species within the Aquibium genus, further substantiated its novelty. The genome of strain LZ166T was 6,119,659 bp in size with a 64.7 mol% DNA G+C content. The predominant fatty acid was summed feature 8 (C18:1ω7c and/or C18:1ω6c). The major polar lipids identified were Diphosphatidylglycerol (DPG), phosphatidylethanolamine (PE), glycolipid (GL) and phosphatidylglycerol (PG), with ubiquinone-10 (Q-10) as the predominant respiratory quinone. Genomic annotation indicated the presence of genes for a diverse metabolic profile, including pathways for carbon fixation via the Calvin–Benson–Bassham cycle and inorganic sulfur oxidation. Based on polyphasic taxonomic results, strain LZ166T represented a novel species of the genus Aquibium, for which the name Aquibium pacificus sp. nov., is proposed, with the type strain LZ166T (= MCCC M28807T = KACC 23148T = KCTC 82889T).

The erosion of surface pipelines induced by proppant flowback during shale gas production is significant. The surface pipelines in a shale gas field in the Sichuan Basin experienced perforation failures after only five months of service. To investigate the erosion features of L360N, coatings, and ceramics and optimize the selection of two protective materials, a gas-solid two-phase flow jet erosion experimental device was used to explore the erosion resistance of L360N, coating, and ceramic under different impact velocities (15 m/s, 20 m/s, and 30 m/s). An energy dispersive spectroscope, a scanning electron microscope, and a laser confocal microscope were employed to analyze erosion morphologies. With the increase in flow velocity, erosion depth and erosion rate of L360N, coating, and ceramic increased and peaked under an impact velocity of 30 m/s. Maximum erosion rate and maximum erosion depth of L360N were respectively 0.0350 mg/g and 37.5365 µm. Its primary material removal mechanism was plowing of solid particles and microcracks were distributed on the material surface under high flow velocities. Maximum erosion rate and maximum erosion depth of coating were respectively 0.0217 mg/g and 18.9964 µm. Its primary material removal mechanism was the detachment of the binder phase Co caused by plowing. Maximum erosion rate and maximum erosion depth of ceramics were respectively 0.0108 mg/g and 12.4856 µm. The erosion mechanisms were micro-cutting and plowing. Under different particle impact velocity, different erosion morphologies were observed, but the primary erosion mechanism was the same. The erosion resistance of ceramics was higher than that of coating. Therefore, ceramic lining materials could be used to protect the easily eroded parts, such as pipeline bends and tees, and reduce the failure rate by more than 93%. The study provided the data and theoretical basis for the theoretical study on oil and gas pipeline erosion and pipeline material selection.

Predicting the thermophysical properties of designed materials at the nanoscale is crucial. However, this remains a significant challenge despite numerous efforts by researchers and scientists. This paper presents a unified thermodynamic model to study the size and shape-dependent cohesive energy and the melting temperature of semiconductor nanosolids, including InSb, ZnSe, CdS, and CdSe. The model provides insight into the thermal stability of nanosolid materials by considering the combined impact of size, shape, and packing density. The finding indicates that smaller nanoparticles exhibit a lower cohesive energy than larger ones. Our unified thermodynamic model yields results consistent with experimental values and demonstrates a closer agreement than those from the universal liquid drop model of size-dependent cohesive energy, which includes a shape factor of α = 2/3 for nanowires. According to the results, the melting temperature of nanoparticles drops as their size decreases. Below a diameter of 5 nm, this trend becomes more noticeable. In the nano-scale domain, the nanoparticle's shape also matters greatly. In particular, compared to tetrahedral nanoparticles, nanowires show a lesser reduction in melting temperature. Also, up to a diameter of roughly 10 nm, the melting temperatures of these nanoparticles rise with particle size. The search results show that, especially in the < 5 nm size range, the size and shape of nanoparticles significantly affect their melting point. The models accurately predict the relationship between particle size and melting point for various semiconductor nanomaterials, aligning with experimental findings. Interestingly, the information indicates a potential preference for these nanomaterials to form nanowire structures in the < 5 nm size range. Our research offers helpful insights into the thermophysical properties of these semiconducting materials, which may have significant implications for their use in a diversity of technological applications.

This study aims to conduct a content analysis of the postgraduate theses on the education of the concept of atom in Turkey from 2000 to 2023. The study utilized the document analysis method, a qualitative research design approach. The theses were obtained by conducting a search in the "Thesis Center" of the Council of Higher Education (YÖK). "Thesis Classification Form" and "Thesis Screening Form" were used as data collection tools. Content analysis was performed on 51 theses that were conducted between 2000 and 2023 and whose full versions were accessed. It was observed that the theses were conducted in 25 different universities, using more than one data collection tool and analysis method. It was determined that most of the theses were supervised by academicians having the title of Prof.Dr. It was determined that almost all of the theses were conducted in the form of research-studies, qualitative research approach was mostly used as the research method, quasi-experimental model was mostly used as the research model, and students were generally used as the sample group. The most widely used data collection tools in the theses were interviews and achievement tests, while t-tests and content analysis were used as analysis techniques. In the selection of thesis topics, the studies in which teaching methods were tried the most were conducted. It was determined that students had difficulty in understanding the concept of atom and had misconceptions.

Background: Post-acute sequelae of SARS-CoV-2 infection (PASC) is a complicated disease that affects millions of people all over the world. Previous studies have shown that PASC impacts 10% of SARS-CoV-2 infected patients of which 50-70% are hospitalized. It has also been shown that 10-12% of those vaccinated against COVID-19 were affected with PASC and its complications. The severity and the later development of PASC symptoms is positively associated with the early intensity of the infection. Results: The generated health complications caused by PASC involve a vast variety of organ systems. Patients affected by PASC have been diagnosed with neuropsychiatric and neurological symptoms. Cardiovascular system also has been involved and several diseases such as myocarditis, pericarditis, and coronary artery diseases were reported. Chronic hematological problems such as thrombotic endothelialitis and hypercoagulability were described as a condition that could increase the risk of clotting disorders and coagulopathy in PASC patients. Chest pain, breathlessness, and cough in PASC patients were associated with respiratory system in long COVID-19 causing respiratory distress syndrome. The observed immune complications were notable, involving several diseases. Renal system also was impacted and result in raising the risk of diseases such as thrombotic issues, fibrosis, and sepsis. Endocrine gland malfunction can lead to diabetes, thyroiditis, and male infertility. Symptoms such as diarrhea, nausea, loss of appetite and taste were also among reported observations due to several gastrointestinal disorders. Skin abnormalities might be an indication of infection and long-term implications such as persistent cutaneous complaints were linked to PASC. Conclusions: Long COVID is a multidimensional syndrome with considerable public health implications, affecting several physiological systems and demanding thorough medical therapy as well as more study to address its underlying causes and long-term effects.

The excellent properties of carbon fibers, in combination with the high price of carbon fibers, makes it interesting to recycle these fibers. Pyrolysis is already an established recycling method to recover the carbon fibers, but in this process also the sizing is removed which could result in lower mechanical properties because of bad adhesion between the fiber and matrix. In this study, recycled carbon nonwoven reinforcements made from pyrolyzed carbon fibers were pre-treated in order to improve the mechanical properties of recycled carbon polyamide and recycled carbon polypropylene composites. The pre-treatment involves applying a to the matrix adapted primer coating to the nonwoven by spraying. Via compression molding, polyamide and polypropylene composites were prepared with and without pretreatment. The tensile and interlaminar shear strength of these composites were measured to determine the effect of the pretreatment. Results revealed that both strengths could be increased by pretreatment of the carbon nonwoven and the increase was largest for the PP composites.

The most recent National Research Council Nutrient Requirements for Sheep and Goats was published in 2007, one of the most consequential nutrient requirement recommendations for sheep and goats in the world. It is pertinent to continue the refinement and discussion of nutrient utilization and requirements for the purposes of enhancing the efficiency of production systems, maximizing resource economy, and minimizing the carbon footprint, among others. Progress has been made in the estimation of energy and protein requirements in sheep and goats, mainly utilizing empirical feeding experimentation, comparative slaughter technique and minimum endogenous loss method. In sheep, newer estimates of energy and protein requirements for maintenance and growth and partial efficiencies had been reported since 2007. There were suggestions that energy and protein requirements could have been affected by breed, wool growth, gender and size; with these reported values being similar or lower than the recommended values in international feeding systems such as NRC, ARC, INRA and AFRC. In goats, energy and protein requirements for growing goats were reported to be either higher or lower than the established recommendations, depending upon meat or dairy breeds. Effect of gender on energy requirement appeared to be related to the stage of growth or degree of maturity. Newer data also suggested that the guidelines of the major feeding systems for the entire growth phase may not be adequate for non-pregnant and non-lactating pubertal females. In multiparous pregnant goats, energy and protein requirements for maintenance did not appear to be affected by days of pregnancy, but efficiencies of metabolizable energy and metabolizable protein utilization for pregnancy were. There were suggestions that that metabolizable protein synthesis in the rumen can be predicted from energy intake using combined equations that encompass both sheep and goats, but more data on goats were called for to account for specific differences in nutrition. In addition to sulfur, there has been progress made on the estimation of maintenance and growth requirements of calcium, phosphorus, potassium and magnesium in goats, with suggestions on the consideration of gender and breed differences. Species, level of Intake, genotype, mature size, age, gender, body composition, use of tissue energy, activity, season, and acclimatization continue to be important considerations for the estimation of nutrient requirements in sheep and goats, with emerging factors such as climate change, heat stress, parasitism and secondary plant compounds. Model equations and partial efficiencies used by NRC to predict energy and protein requirements for maintenance, growth, lactation, and fiber have been highlighted and discussed for the purpose of a more focus discussion and refinement for the future. Potential and limitation of both traditional and emerging methodologies in determining the nutrient requirements in sheep and goats were discussed. To justify the research investment, emerging methodologies such as nutrigenomics will have to be linked more directly to the improvement of production efficiency via more precise prediction of nutrient requirement.

The aim of this study was to investigate the physicochemical characterization and biological activities of chitosan (CH) based composite films with the incorporation of chestnut flower essential oil (CFEO). The composite films were prepared by casting method and characterized in terms of structural, morphological and mechanical properties via FT-IR, XRD, UV, SEM and TGA. The results proved the significantly increased water vapor permeability (WVP), heat resistance, antibacterial and antioxidant capabilities of CH-CFEO films. The incorporation of CH and CFEO enhanced the UV blocking, which made the film shield almost all UV light. Films with the tensile strength of 6.37 ± 0.41 MPa and elongation at break of 22.57 ± 0.35% were got with 6 mg mL-1 CFEO. Subsequently, the fruit preservation experiments also confirmed that the composite films could effectively extend the shelf life of bananas through their excellent water vapor and oxygen barrier. These desirable performances enable our newly developed composite films to be a remarkable packaging material to solve the fresh fruit preservation dilemma.

The exceptional performance advantages of the fiber optic gyroscope (FOG) position it as a dominant player in middle and high-end inertial navigation systems. To prevent the loss of sensor precision caused by algorithm design and simplify the complex modeling strategy in traditional methods. We gradually demonstrate the significant role of Convolutional Neural Network (CNN) in the navigation system based on FOG, and utilize the particle swarm optimization algorithm (PSO) to expedite the convergence of the network. The experimental results demonstrate that the initial alignment method based on deep learning is more accurate than the traditional method. The attitude angle error is reduced by 81.25%, 92.54% and 36.53% respectively. The research provides support for the future application of deep learning in optical navigation systems.

This research concerns in to understand the link between urban heat and cool island, the Local Climatic Zones (LCZ) and atmospheric systems during the winter season in the city of Balneário Camboriú, Southern Brazil. To collect meteorological data on urban environmental, 11 permanent points in the Balneário Camboriú metropolitan region were installed. To understand the atmos-pheric systems operating in the region, a synoptic analysis of the dates was performed, and then, the LCZs map created for the city in World Urban Database and Acess Portal Tools was used to cor-relate the magnitudes of the heat and cool islands found in Balneário Camboriú in the winter period. The results indicate that the increasing verticalization with the construction of skyscrapers in Balneário Camboriú has a significant influence on local conditions for the occurrence of heat and cold islands. The findings indicate that LCZs with sparsely distributed buildings (LCZs 6, 8 and 9) and LCZs with dense vegetation (LCZ A) have lower intensity magnitudes of heat and cool con-ditions. The biggest magnitudes of heat and cool islands were reported in LCZs 1 and 3 during the timeframe. The synoptic analysis supports earlier researches that points to atmospheric stability (Anticyclonic domain) as a favorable atmospheric setting for the emergence of urban hear and coolness islands.

The intrusion of seawater in coastal aquifers in Greece is a particularly widespread phenomenon. The coastline of Greece has a length of 15,147 km. Once groundwater resources are contaminated, remediation strategies are difficult, costly and time consuming. In this paper three coastal aquifer systems of Peloponnese are studied. Initially the main ions and cations were calculated for the three aquifers. According to the results from hydrochemical analyzes Na+,Mg2+, Ca2+, SO4-2, Cl- have high values and are affected by the intrusion of seawater into the coastal aquifers. It estimates the vulnerability of groundwater to the intrusion of seawater. Using Geographical Information Systems (GIS) software, maps are prepared for the presentation of each parameter of the GALDIT method. The main factors that affect the seawater intrusion are basically presented in the 6 letters of the acronym GALDIT. The analysis of each parameter is as follows: Groundwater occurrence (aquifer type: unconfined, confined, and leaky confined), Aquifer hydraulic conductivity, depth to groundwater Level above the sea, Distance from the shore (inland distance perpendicular from shoreline), Impact of existing status of sea water intrusion in the area and Thickness of the aquifer. The final map that emerged from the study of the three groundwater systems shows the vulnerability of seawater intrusion in Peloponnese. The maps show that the groundwater system of Larissos presents lower vulnerability to the seawater intrusion compared to the other two groundwater systems. This is because the occurrence of flysch in the northern part of the area acts as a barrier to the penetration of seawater.

In this project, four of fibers Bragg gratings were fabricated by injecting different volumes of liquids (star line Glass Mechanix optical adhesive material, olive oil diluted with ethanol) into the hollow core fiber. The amplitude splitting interferometric technique with a high resolution specially designed translation stage was used for the fabrication process. The fabrication was done using ultraviolet laser operated at wavelength 405nm. The fabricated Bragg length of the four fibers is equal to 3.8 cm. The results presented fiber Bragg grating (FBG) with successful fabrication at 653.3 nm Bragg reflected wavelength.

The North China Plain is among the regions most afflicted by ground fissure disasters in China. Recent urbanization has accelerated ground fissure activity in the three counties of the northern North China Plain, posing significant threats to both the natural environment and socioeconomic sustainability. Despite the increased attention, a lack of comprehensive understanding persists due to delayed recognition and limited research. This study conducted field visits and geological surveys across 43 villages and 80 sites to elucidate the spatial distribution patterns of ground fissures in the aforementioned counties. By integrating these findings with regional geological data, we formulated a causative model to explain ground fissure formation. Our analysis reveals a concentration of ground fissures near the Niuxi and Rongxi faults, with the former exhibiting the most extensive distribution. The primary manifestations of ground fissures include linear cracks and patch-shaped collapse pits, predominantly oriented in east-west and north-south directions, indicating tensile failure with minimal vertical displacement. Various factors contribute to ground fissure development, including fault activity, ancient river channel distribution, bedrock undulations, rainfall, and ground settlement. Fault activity establishes a concealed fracture system in shallow geotechnical layers, laying the groundwork for ground fissure formation. Additionally, the distribution of ancient river channels and bedrock undulations modifies regional stress fields, further facilitating ground fissure emergence. Rainfall and differential ground settlement serve as triggering mechanisms, exposing ground fissures at the surface. This research offers novel insights into the causative mechanisms of ground fissures in the northern North China Plain, providing valuable scientific evidence for mitigating ground fissure disasters during the urbanization process in the region.

In this investigation dyeing of alginate fiber was carried out after cationic treatment of EPTAC (2, 3-Epoxypropyl Trimethyl Ammonium Chloride). Optimum dyeing process and parameter show good dyeing performance when alginate fiber dyed with rhubarb dye. In addition to cationic treatment is taken into account for alginate fiber to improve fastness, color strength, breaking strength. Later in dyeing for fixation ferrous sulfate, copper sulphate was considered as mordents. Moreover using pre-mordanting methods conveyed the dyeing of alginate fiber with the stave of metallic mordant and without metallic salt mordents. The evaluation of each color dyed material was done through following two terms for instance CIELAB (L*, a*, and b*) and K/S values. According to AATCC test methods color fastness to washing of the dyed fiber was determined whereas according to the ASTM D3822M standard the breaking strength of alginate fiber was estimated and tested. When dyeing was carried out on alginate fiber through considering optimum parameter like 80◦C for 90 min, M: L 1:40 and at pH 7 which showed optimum results. In addition to mostly very good wash fastness was obtained while there was no fading of the color, whereas the moderate level of color fastness to crocking was achieved. Later after dyeing the evaluations of SEM of the cationized alginate fiber and FTIR of powder from the rhubarb dye were observed. The results suggested that the surface of cationized alginate fiber was smoother than the raw alginate fiber.

In an effectively managed grazing system, goats as grazers can benefit the land's physical, chemical, biological, and economic aspects. However, little research has evaluated rotational and continuous goat grazing in Kentucky. This observational study investigated the impact of rotational and continuous grazing on forage production and goat performance. One group of 10 does was placed on a rotational pasture, and another group of 10 does were placed on a continuous pasture, each pasture measuring two acres. The pastures were side-by-side with similar forage types and compositions. Goat performance was measured by body weight and eye color score (FAMCHA). Forage production was measured weekly by collecting forage heights at three random spots in each pasture. The rotational grazing field displayed a more evenly grazing pattern, while the continuous field experienced overgrazing in some areas and overgrown of the less desired forage. Goats on the continuous field had a decrease in body weight, while the weights were more consistent in the rotational grazing field. The FAMACHA score was temporarily reduced on the rotational grazing pasture, indicating that properly managed rotational grazing may prevent anemia, possibly by reducing the shedding of gastrointestinal parasites. However, due to drought and lack of forage, the FAMACHA score of goats in the rotational grazing system reverted to its original status by the end, indicating that more extensive management and timely adjustments are necessary to ensure optimal goat performance. Our results suggest that rotational grazing may support more consistent forage yields and body weights of goats and has the potential to reduce the incidence of anemia and parasitic infestations in goats in Kentucky.

Indonesia is one of the largest banana producing countries in the world remaining abundance solid waste of banana fruit bunch. The banana fruit bunch contains high natural fibers which were obtained by an impregnation process using potassium hydroxide (KOH) and followed by a carbonization process under steam at 250°C for 5 h. The nanomaterial of TiO₂/fibre was prepared by a hydrothermal process at 200°C for 4 h. Surface morphology proved that the TiO₂ was loaded into the fibre by an increasing roughness of the surface and irregular size of porosity. The development of amorphous to crystalline phase of TiO₂/fibre was clearly observed. The effectiveness of TiO₂/fibre for removal of rhodamine B was investigated from different parameters of adsorptions in aqueous solution. The equilibrium adsorptions show that the Langmuir and Freundlich isotherm exhibited the best correlation coefficient (R² > 0.94) relating to the chemisorption and physisorption interaction in the adsorption process. Kinetic models were well described by the pseudo-first and second-order with the best correlation coefficient (R² > 0.99). These results indicate that nanomaterial TiO₂/fibre can be used as an effective adsorbent for removal of rhodamine B in aqueous solution.

To study the spatial accessibility of healthcare services in cities on the Tibetan Plateau, this paper proposes an improved 3SFCA method in the main urban area of Xining City. The improved 3SFCA method incorporates both selection weights from the Huff model and the M2SFCA approach to addressing suboptimal allocation of supply resources. Results show that the accessibility of healthcare for the main urban area of Xining City decreases in a circle to four axes, with good accessibility in the east and center but poor accessibility in the north. And there is a positive spatial relationship between population and accessibility. Besides, this paper proposes a framework for studying the spatial accessibility of healthcare on the Tibetan Plateau.

The Kampar Peninsula, a significant peatland region in Riau, Indonesia, is vital for its carbon re-serves and biodiversity, including the Sumatran tiger. Covering approximately 735,091 hectares, it comprises critical peat domes essential for hydrological balance. This research investigates land use changes from 1990-2020 using the Normalized Difference Fraction Index (NDFI) to map disturb-ances and land cover changes. Additionally, interviews and regulatory analysis were conducted to examine the historical drivers of land use change in the Kampar Peninsula. In 2020, natural forests covered 433,395.20 hectares (59.9% of the total area), industrial pulpwood plantations (primarily acacia) covered 27.3%, oil palm plantations accounted for 10.4%, infrastructure occupied 2.4%, and water bodies made up 0.9%. Key drivers of land use change include the construction of access roads by oil companies since 1975 and government policies during the New Order period (1980s-1998) promoting forest exploitation and transmigration programs. These activities have significantly transformed the Kampar Peninsula's land cover, highlighting the need for sustainable management and conservation efforts.

The variation of aerosols, especially dust aerosol, in time and space plays an important role in climate forcing studies. Aerosols can effectively reduce land surface longwave emission and re-emit energy at a colder temperature, making estimation of downwelling surface longwave radiation (DSLR) with satellite data difficult. Using the latest atmospheric radiative transfer code (MODTRAN 5.0), we simulate the outgoing longwave radiation (OLR) and DSLR under different land surface and atmospheric profile conditions. The results show that dust aerosol has an obvious “warming” effect to longwave radiation compared with other aerosols, that aerosol longwave radiative forcing (ALRF) increased with increasing aerosol optical depth (AOD), and that the atmospheric water vapor content (WVC) is critical to the understanding of ALRF. A method is proposed to improve the accuracy of DSLR estimation from satellite data for the skies under heavy dust aerosols. The AOD and atmospheric WVC under cloud-free conditions with a relatively simple satellite-based radiation model that yields the high accurate DSLR under heavy dust aerosol are used explicitly as model input to reduce the effects of dust aerosol on the estimation of DSLR. Validations of the proposed model with satellites data and field measurements show that it estimates the DSLR accurately under heavy dust aerosol skies. The root mean square errors (RMSEs) are 20.4 W/M² and 24.2 W/M² for Terra and Aqua satellites, respectively, at the Yingke site, and the biases are 2.7 W/M² and 9.6 W/M², respectively. For the Arvaikheer site, the RMSEs are 23.2 W/M² and 19.8 W/M² for Terra and Aqua, respectively, and the biases are 7.8 W/M² and 10.5 W/M², respectively. The proposed method is especially applicable to acquire relatively high accurate DSLR under heavy dust aerosol using MODIS data with available WVC and AOD data.

The organic fraction of municipal solid waste (OFMSW) is a significant environmental threat, and an economic and social challenge to manage. As such, the efficient treatment of OFMSW is a significant key factor in achieving sustainable waste management. Decentralized Composting (DC) develops a new framework of waste management. The DC Analysis Model (DCAM), proposed in our previous study, provides a powerful tool for decision makers, based on the quantification of the DC project characteristics. In this paper, we focus on the qualitative analysis as a complementary tool to support decision making, in cases where quantitative analysis is unequivocal. The qualitative analysis identifies the main players in the field, the critical stakeholders and the potential conflicts between them. It also reveals the root problems and the core competencies for the project's implementation. DCAM qualitative analysis in Shefa-Amr (case study) indicates that unresolved root problems, such as the “lack of national regulation”, “clear ownership of the project” and “lack of ongoing budget” can result in an unsustainable composting system. Countering that, “the commitment of the municipality”, together with “economic viability” and securing “suitable areas for placing composters” are among the most important core competencies for the effective implementation of DC projects.

Superior fiber quality is one of the most important objectives in cotton breeding. To detect the genetic basis underlying fiber quality, an F2 population containing 413 plants was constructed by crossing Jifeng 914 and Jifeng 173, both of which have superior fiber quality, with Jifeng 173 being better. Five fiber quality traits were investigated in the F2, F2:3, F2:4, and F2:5 populations. Quantitative trait loci (QTL) mapping was conducted based on a high-density genetic map containing 11,488 single nucleotide polymorphisms (SNPs) and spanning 4,202.12 cM in length. Transgressive segregation patterns and complex correlations in the five tested traits were observed. A total of 108 QTLs were found, including 27 for fiber length (FL), 16 for fiber strength (FS), 24 for micronaire (MC), 17 for fiber uniformity (FU), and 24 for fiber elongation rate (FE). Chromosome A7 contained 12 QTL, ranking the first. No QTL was found on chromosome D1 and D11. Each QTL contributed 1.98%–21.45% to the phenotypic variation (PV), including 13 major effect QTLs that contributed more than 10% toward PV. Two QTLs could be repeatedly detected in three populations, including qFL-D3-2 in F2, F2:4, and F2:5 with 9.18%–21.45% of PV, qFS-A11-1 in F2:3, F2:4 and F2:5 with 6.05%–10.41% of PV. Another seven stable QTLs could be detected in two populations, including four major effect QTLs: qFL-A12-3, qFS-D10-2, qMC-D6-2, and qMC-D8-1. Fourteen QTL-overlapping regions were found, which might explain the complex correlations among the five phenotypic traits. Four regions on chromosome A11, D3, D6, and D10 covered by both stable and major effect QTLs are promising for further fine mapping. The genomic regions of the two QTLs detected in three populations and the four major effect QTLs contain 810 genes. Gene functional analysis revealed that the annotated genes are mainly involved in protein binding and metabolic pathways. Fifteen candidate genes in the qFL-D3-2 region are highly expressed in fiber or ovules during fiber initiation, elongation, secondary cell wall thickening, or maturation stages. qRT-PCR revealed that Ghir_D03G005440.1 and Ghir_D03G011310.1 may play a role in promoting fiber initiation, Ghir_D03G006470.1 may be beneficial for promoting fiber elongation. This study provides more information for revealing the molecular genetic basis underlying cotton fiber quality.

Although social sustainability plays a crucial role in the sustainable development agenda, there is a scarcity of research that clearly defines and fully operationalizes this concept. This study seeks to fill this gap in the literature by creating a comprehensive measurement scale to evaluate social sustainability in the context of urban parks. According to the literature review, social sustainability is identified as a multidimensional concept, encompassing eight key dimensions in urban parks: identity, place attachment, cohesion, safety, equity, facilities, comfort, and accessibility. The validity, reliability, and dimensions of the social sustainability scale for urban parks are examined using factor analysis. To explore the idea that user evaluations of urban parks can be employed as a method to ensure social sustainability, user feedback was collected for the study. The article evaluates data from 120 participants in Alaeddin Hill Park, located in Konya, Turkey—a site selected for its potential to best reflect the identified dimensions. This study reveals the relationships between different dimensions of social sustainability that influence the park's social sustainability performance at the urban park scale. Additionally, it provides insights aimed at improving park design quality. The findings of the study indicate that the park’s social sustainability is at a moderate level, with identity identified as the most influential dimension. On the other hand, the dimension that most negatively impacts sustainability performance is safety, primarily due to low perceptions of safety caused by inadequate lighting, the predominant use of the park by people from lower socioeconomic backgrounds, and a general lack of security.

The impact of legume production on smallholder farmers' socio-economic welfare in Ma-lawi is a crucial question, given the country's aspirations for rural development and eco-nomic growth. This study investigates the effect of legume production on household wel-fare, using two waves of nationally representative data from the Integrated Household Survey and integrating geospatial techniques. A random effects model was employed to estimate the determinants of legume adoption, and the impact of legume cultivation on household welfare was assessed using income and asset holding as indicators. The results show that legume adoption significantly increases household income per capita and household asset holding by 71%. Disaggregated results reveal that adoption benefits all households, but particularly those with larger landholdings. The study concludes that accelerating legume adoption is a promising strategy for rural development in Malawi, aligning with the country's goals of achieving inclusive wealth and self-reliance in the coming decades.

The present study focuses on the development and optimization of a highly efficient unique hybrid technique — membrane-assisted gas absorption (MAGA) in designing the separation unit, which provides the improvement in mass-transfer of a target component during the natural gas processing in terms of sweetening stage. A novel design of membrane-assisted gas absorption cell is used to enhance the ratio between absorbent amount and membrane surface available for permeation. The performance tests were implemented on example of two gas mixtures separation: one is model ternary gas mixture and the second is quasi real natural gas, which includes number of hydrocarbons, nitrogen, acid impurities and xenon. For both cases, the MAGA unit demonstrated high acid gases removal efficiency, and high recovery of hydrocarbons. The ultimate efficiency of studied system was up to 96 and 61 % of removed acid gases with hydrocarbons losses up to 1 % at highest productivity. In this way, the residual sum of acid gases content may be lowered to 1 vol.% using the heat-free hybrid membrane-assisted gas absorption unit maintaining suitable recovery rate of methane, ethane, propane and n-butane. Nevertheless, the overall efficiency of the process may be enhanced using the specific absorption agents with aqueous amino alcohol solutions.

Indigenous traditional land uses, including hunting, fishing, sacred activies and land-based education at Red Sucker Lake First Nation (RSLFN) in Manitoba, Canada are impacted by mining. Traditional land use maps and interviews were undertaken with 21 Indigenous people from RSLFN, showing many traditional land uses are concentrated on greenstone belts. The interviews revealed that mining exploration has resulted in large petroleum spills, noise distress, personal property destruction, wildlife die-offs and animal population declines, which negatively impact RSLFN’s traditional land use practices, ecosystem integrity, and community health. Red Sucker Lake First Nation (RSLFN) people want their territories’ land and water protected for traditional uses, culture and ecological integrity. Towards this goal, their Island Lake Tribal Council sought support for an Indigenous-protected and conserved area (IPCA) in their territory outside of existing mining claims, but without success. Governments need to partner with Indigenous nations to reach their biodiversity targets, particularly considering northern Canada’s peatlands, including those in Island Lake, surpassing the Amazon forests for carbon storage. Critical minerals and gold’s role in renewable energy and geopolitics have colonial governments undermining Indigenous rights, climate stabilization and biodiversity. With extractivism prioritized, the environmental impacts of mining extend to not only the mines but also the extensive development required to facilitate extraction including roads, hydro and ports to ship the minerals with proposals for a national Northern Corridor to run nearby.

The study investigated the impact of traditional medicine on life expectancy in Nasarawa State, Nigeria. The study adopted a quantitative research approach. Purposive or judgmental sampling was used to elucidate the data set used for the study. Cross-sectional data were gathered with the help of a well-designed questionnaire from a total of three hundred and fifty-seven (357) respondents who were available for the survey. The data set collected was analysed using descriptive and linear regression using Ordinary Least Squares (OLS). From the results, 53%, 87%, and 56% were male, below 50 years old, and in the low-income class, respectively, suggesting that the bulk of the respondents under investigation were male, young, and had rather modest incomes. Also, 53% were married, and all had one form of formal education. 67% of respondents acknowledge using traditional medicine; however, the majority of respondents preferred Orthodox medical care over alternative kinds of care. Traditional medicine (TM) and factors that contribute to the advancement of traditional medicine (FITM) have a negative impact on life expectancy, according to the regression analysis. On the other hand, TM has no statistically significant impact on life expectancy, despite FITM having a statistically significant effect at the 5% level. All available data, however, indicates that TM and FITM have an impact on life expectancy, either directly or indirectly. Based on the results, this study concluded that traditional medicine has the potential to significantly increase life expectancy in Nasarawa State and throughout Nigeria. The study recommends that traditional health professionals, stakeholders, and concerned government agencies should put efforts in place to improve and promote modern traditional medicine among the people, especially its effectiveness and medicinal quality, increase its accessibility to people, and efficiently regulate its prices to increase its affordability for low-income earners.

Some wrong decisions and faulty practices applied during the repair and restoration of traditional buildings cause more damage to the structures due to the materials used in the repair. In this study, brick, mortar, plaster, and wood samples were taken from one registered building in the Konuralp neighborhood of Düzce Province, which has survived to the present day by preserving its original structural features and reflecting the characteristics of traditional housing. Texture, chemical and petrographic analyses were carried out on the samples. In line with these analyses, a scientific basis was created for selecting material properties in the repair and reuse processes of traditional buildings, and suggestions are made for the analysis of materials specific to traditional buildings in Konuralp.

The extensive utilization of drones has led to numerous scenarios that encompass both advantageous and perilous outcomes. By using deep learning techniques, it is aimed to reduce the dangerous effects of drone use through early detection of drones.The state of the art of the study is evaluation of deep learning approaches such as pre trained YOLOv8 drone detection for security issues. In this study, dataset collected by Mehdi Özel for a UAV competition are sourced from GitHub. These images are labeled using Roboflow, and the model is trained on Google Colab. To enhance model performance, dataset augmentation techniques including rotation and blurring are implemented. Following these steps, a significant precision value of 0.946, a notable recall value of 0.9605 and a considerable precision-recall curve value of 0.978 are achieved, surpassing many popular models such as Mask CNN, CNN, and YOLOv5.

Morphological and phylogenetic (45S nrDNA+RPB1 gene) analyses of three glomoid spore-producing arbuscular mycorrhizal fungi revealed the presence of two new species be-longing to the genus Glomus in the family Glomeraceae. In the field, Glomus highlandensis sp. nov. was found in a saltmarsh of the Scottish Highlands and in maritime sand dunes of the Baltic Sea in Poland, both saline environments, while G. mongioie sp. nov. originates from the Italian Alps. Phylogenetic placement analysis using environmental sequences indicated that G. highlandensis could have likely worldwide distribution while G. mongioie seems to be a rare species in the world. The molecular and phylogenetic analysis provided important insights about the presence of ribosomal variants in Glomus, with potential negative implication in phylogeny and species recognition.

This study reports on the development of bio-based hydrophobic coatings for packaging papers through deposition of polyhydroxybutyrate (PHB) particles in combination with nanofibrillated cellulose (NFC) and plant wax. In a first approach, PHB particles in micrometer range (PHB-MP) were prepared through a phase-separation technique providing internally nanosized structures. The particles were transferred as a coating by dip-coating filter papers in the particle suspension, followed by sizing with a carnauba wax solution. This approach allowed partial to almost full surface coverage of PHB-MP over the paper surface resulting in static water contact angles of 105° to 122° and 129° to 144° after additional wax coating. In a second approach, PHB particles with submicron sizes (PHB-SP) were synthesized by an oil-in-emulsion (o/w) solvent evaporation method, and mixed in aqueous suspensions with 0 to 7 wt% NFC. After dip-coating filter papers in PHB-SP/NFC suspensions and sizing with a carnauba wax solution, static water contact angles of 112° to 152° were obtained. The intrinsic properties of the particles were analyzed by scanning electron microscopy, thermal analysis and infrared spectroscopy, indicating higher crystallinity for PHB-SP than PHB-MP. The chemical interactions between the more amorphous PHB-MP particles and paper fibers were identified as an esterification reaction, while the morphology of the NFC fibrillar network was playing a key role as binding agent in the retention of more crystalline PHB-SP at the paper surface, hence contributing to higher hydrophobicity.