Ab initio density functional theory molecular dynamics extensive calculations were used for the first time to evaluate stability conditions for relevant phases of InN. In particular, thermal decomposition of InN with formation of N2 molecules and pressure induced wurtzite – rocksalt solid-solid phase transition were established. The results consistent with available experimental data allowed a critical evaluation of potential and limitations of the proposed simulation method. The ab initio molecular dynamics as an efficient tool for simulations of phase transformations of InN including solid-solid structural transition and thermal decomposition with formation of N2 molecules has been demonstrated. It is of high interest because InN being important component of epitaxial quantum structures has still not been obtained as a bulk single crystal making difficult a determination of its basic physical properties and designing new applications.

The Eastern Kunlun Fault Zone (EKFZ) is located in a seismic blank area. This study investigates the hydrogeochemical characteristics of varied-temperature springs in the EKFZ to understand the relationship between fractures, fluids and earthquakes. It aids in establishing their induction mechanisms and assists in monitoring the earthquake precursors of the EKFZ. In this study, the main elements, trace elements, hydrogen and oxygen isotopes and strontium isotopes of 23 varied-temperature springs in the EKFZ were analyzed. The results reveal the source of groundwater recharge, hydrochemical types, mineral saturation, and for a select few springs indicative of geothermal activity, collected geothermal reservoir temperatures. The study also explores the relationship between earthquakes and springs, identifying sensitive chemical indicators. Based on continuous monitoring at Maqu Station, we found that before the occurrence of the Maerkang Ms 6.0 earthquake, the concentration of Cl− rose by 2.9 times, and 46 days before the Gande earthquake (Ms = 4.7), the concentrations of Na+ and SO42− significantly increased. Finally, a conceptual model of the hydrogeochemistry of springs is presented to describe the groundwater circulation in the study area. This research is of great significance for the analysis of fluid geochemistry in this area and for assessing the seismic hazards of the EKFZ.

As a member of smart materials, electrorheological elastomers (EREs) formed by pre-treating active electrorheological particles are attracting more and more attention. In this work, four Mg-doped strontium titanate particles with spherical, dendritic, flake-like and pinecone-like morphorlogies were obtained by hydrothermal and low-temperature co-precipitation. XRD, SEM, Raman and FT-IR were used to characterize the obtained products. The results showed that the sizes of Mg-doped strontium titanates are about 1.5‒2.0 μm, and the phase structure are dominated by cubic crystal. These Mg-doped strontium titanates were dispersed in a hydrogel composite elastic medium. Then, Mg-doped strontium titanate/glycerol/gelatin electrorheological composite hydrophilic elastomers were obtained with or without electric field. The electric field response properties of Mg-doped strontium titanate composite elastomers were investigated. It concluded that dendritic Mg-doped strontium titanate composite elastomers is high-performance EREs. And the maximum value of energy storage modulus of Mg-doped strontium titanate composite elastomers has achieved 8.70 MPa. This high electrorheological performance of the products is helpful for their applications in vibration control, force transducers, smart structures, dampers, and other fields.

Background: A Morel–Lavallée lesion (MLL) is a traumatic, internal closed degloving injury that results from shearing of subcutaneous tissue away from underlying fascia, usually associated with high-velocity trauma. Case presentation: A 52-year-old man was transported to hospital for further follow-up of a superficial femoral artery injury. Examination on admission showed bruising seen around the left thigh. Contrast-enhanced computed tomography of the left thigh revealed hematoma with extravasation from a branch of the left superficial femoral artery, but no apparent aneurysms or femoral fractures. The patient was treated with compression bandages and discharged on hospital day 6. He left hospital able to walk unaided. He subsequently complained of left thigh pain with swelling and visited the hospital several times. He was treated at another outpatient clinic and was diagnosed with MLL. Single-use disposable portable negative pressure wound therapy (NPWT) was applied for about 2 months, achieving a stable wound site. Conclusion: We encountered a case of MLL successfully treated with single-use portable NPWT. This report presents the case of a patient with isolated MLL without fracture in the left thigh, in which the diagnosis was missed on initial admission. Finally, the patient received minor interventions including drainage along with tissue debridement and portable NPWT. We reviewed the relevant literature and summarize the pathogenesis, clinical manifestations, and treatment strategies for MLL. Emergency physicians require an increased understanding of MLL to avoid misdiagnosis and missed diagnosis.

Using the example of III-V nitrides crystallizing in a wurtzite structure (GaN, AlN, InN), this review presents the special role of hydrostatic pressure in studying semiconductor properties. Starting with a brief description of high pressure techniques for growing bulk crystals of nitride compounds, we focus on the use of hydrostatic pressure techniques in both experimental and theoretical investigations of special properties of nitride compounds, their alloys and quantum structures. The band gap pressure coefficient is one of the most important parameters in semiconductor physics. Trends in its behavior in nitride structures, together with trends in pressure-induced phase transitions, are discussed in the context of the behavior of other typical semiconductors. Using InN as an example, the pressure-dependent effects typical of very narrow bandgap materials, such as conduction band filling or effective mass behavior, are described. Interesting aspects of bandgap bowing in In-containing nitride alloys, including pressure and clustering effects, are discussed.Hydrostatic pressure also plays an important role in the study of native defects and impurities, as illustrated by the example of nitride compounds and their quantum structures. Experiments and theoretical studies on this topic are reviewed. Special attention is given to hydrostatic pressure and strain effects in short periods nitride superlattices. The explanation of the discrepancies between theory and experiment in the optical emission and its pressure dependence from InN/GaN superlattices led to the well-documented conclusion that InN growth on the GaN substrate is not possible. The built-in electric field present in InGaN/GaN and AlGaN/GaN heterostructures crystallizing in wurtzite lattice can reach several MV/cm, leading to drastic changes in the physical properties of these structures and related devices. It is shown how hydrostatic pressure modifies these effects and helps to understand their origin.

1) Introduction: Negative pressure wound therapy (NPWT) is a frequently applied open abdomen (OA) treatment. There are only a few experimental data supporting this method and describing the optimal settings and pressure distribution in the abdominal cavity during this procedure. The aim of our study was to evaluate pressure values at different points of the abdominal cavity during NPWT in experimental abdominal compartment syndrome (ACS) animal model. 2) Methods: In this study (permission Nr. 13/2014/UDCAR) 27 Hungahib pigs (15.4- 20.2 kg) were operated. ACS was generated by implanting a plastic bag in the abdomen through mini-laparotomy and filled with 2100- 3300 ml saline solution (37 C°) to an intraabdominal pressure (IAP) of 30 mmHg. After 3 hours, NPWT (Vivano Med ® Abdominal Kit, Paul Hartmann AG, Germany) or Bogota bag was applied. NPWT group was divided into -50, -100 and 150 mmHg suction group. Pressure distribution to the abdominal cavity was monitored at 6 different points of the abdomen via a multichannel pressure monitoring system. 3) Results: The absolute pressure levels were significantly higher above than below the layer. The values of the pressure were similar in the midline than laterally. Amongst the bowels, the pressure values changed periodically between 0 and -12 mmHg which might be caused by the peristaltic movements. 4) Conclusions: The porcine model of the present study seems to be well applicable for investigating ACS and NPWT. It was possible to provide valuable for clinicians. The pressure was well distributed by the protective layer to the lateral parts of the abdomen and this phenomenon did not change considerably during the therapy.

Abstract: Chemical burns are one of the most dangerous and aggressive types of burns as they can cause significant tissue damage, leading to pain, inflammation, necrosis, and scarring. We present a burn case report associated with the use of Acellular Dermal Matrix (MatriDerm® MedSkin Solution Dr. Suwelack AG, Billerbeck, Germany) for the reconstruction of a Hallux after the patient was mistakenly administered intramuscular Nitric Acid at another institution. The patient presented with a third degree burn that compromised the medial aspect of the hallux’s skin, the distal phalanx and nail bed. Early debridement was performed, and Negative Pressure Wound Therapy (NPWT VAC, 3M, US) was used to preserve and promote tissue viability. Eight days later, the patient was taken to the OR, and Acellular Dermal Matrix and split-thickness skin graft were used to reconstruct her right hallux’s defect. The patient achieved adequate clinical evolution and was discharged with complete reconstruction of the burned area. Acellular Dermal Matrix proved to be an important and viable option for reconstructive surgery after a chemical burn, and further studies are warranted to ensure its routine usage in this kind of lesions. Keywords: chemical burn, acellular matrix, hallux reconstruction, NPWT

Negative temperature coefficient (NTC) materials are usually based on ceramic semiconductors and electrons are involved in their transport mechanism. A new type of NTC material, adequate for alternating current (AC) applications, is represented by zeolites. Indeed, zeolites are single-charge carrier ionic conductors with a temperature-dependent electrical conductivity. In particular, electrical transport in zeolites is due to the monovalent charge-balancing cations, like K⁺, capable of hopping between negatively charged sites in the aluminosilicate framework. Owing to the highly non-linear electrical behavior of the traditional electronic NTC materials, the possibility to have alternative types of materials, showing linearity in the electrical behavior, is very desirable. Among different zeolites, the natural clinoptilolite has been selected for investigating the NTC behavior since it is characterized by high zeolite content, convenient Si/Al atomic ratio, good mechanical strength, due to its compact microstructure, and low toxicity. Clinoptilolite has shown a rapid and quite reversible impedance change under heating, characterized by a linear dependence on temperature. X-ray diffraction (XRD) has been used to identify the natural zeolite, to establish all types of crystalline phases present in the mineral, and to investigate the thermal stability of these phases up to 150°C. X-ray photoelectron spectroscopy (XPS) analysis has been used for the chemical characterization of the natural clinoptilolite sample, providing important information on the cationic content and framework composition. In addition, since electrical transport takes place in the zeolite free-volume, a Brunauer–Emmett–Teller (BET) analysis of the mineral has been also performed.

This paper presents a piezoresistive pressure sensor with a shield layer for improved stability. Compared with the conventional piezoresistive pressure sensors, p-type piezoresistors are covered by an n-type shield layer, which is formed by ion implantation. The proposed pressure sensors have been successfully fabricated by bulk micromachining techniques. The impact of electrical field on piezoresistors is studied by simulation. The temperature drift of the pressure sensor has been investigated by both simulation and experimental measurement. Characteristics of developed pressure sensors are tested from -40 C to 125 C. A sensitivity of 0.022 mV/V/KPa and a maximum non-linearity of 0.085% FS are measured for the fabricated sensor in a pressure range of 1 MPa. The temperature coefficients of resistance of shielded piezoresistors are found to be smaller than those of un-shielded ones. It is demonstrated that the shield layer is able to reduce the drift caused by electrical field and ambient temperature variation.

Background and Objectives: Acute compartment syndrome (ACS) is an emergency condition of the lower limb in which prophylactic fasciotomy is required to prevent complications. A negative pressure wound therapy (NPWT) used to the treatment of fasciotomy wounds provide beneficial clinical results. This study aimed to exchange the authors’ experience of using the NPWT installation system on the lower limb wounds after fasciotomy in ACS. Materials and Methods: This is a retrospective study enrolled consecutive patients with ACS, who underwent fasciotomy and was treated with the NPWT installation system at Department of Vascular Surgery, Provincial Hospital in Kielce from April 2016 to July 2017. Results: The study enrolled 15 patients with a diagnosis of ACS (87% men, mean age 65 years old). An open four-compartment fasciotomy (87%) or two-compartment fasciotomy (13%) was performed. The NPWT was applied on the first day after fasciotomy in 87% of patients. Therapy was initiated by the negative pressure of 125 mm Hg, which maintained at this level until the therapy was finalized. In 80% of patients, the vacuum-assisted wound closure (VAC) dressing changes were performed every 3 days. The first approximation of fasciotomy wounds margins occurred on the 4th day after surgery among 67% of individuals. The average time of using VAC on fasciotomy wounds was 9 days. The average time to definitive closure edges of fasciotomy wounds was 12 days. The average time of hospital stay was 17 days. Conclusions: Our experience indicates the legitimacy of using NPWT in wound treatment after fasciotomy in ACS. The NPWT enables faster primary closure of wounds, reduces edema, as well as decreases hospitalization time.

Salmonella Typhimurium is a typical Gram-Negative bacterium associated with food-borne illness threatening public health. This pathogen is reported to have caused millions of infections and thousands of hospitalizations yearly in the United States alone. Salmonella Typhimurium has a sophisticated array of virulent factors, including its flagella, which contributes significantly to its pathogenicity. Cannabidiol (CBD), the non-psychoactive component of the cannabis plant, has attracted the interest of many researchers recently because of its antimicrobial properties. With the growing interest in exploring CBD’s antimicrobial properties, we, in this study, have delved into unravelling how prolonged exposure of Salmonella Typhimurium to CBD influences the expression of the flgA gene. We hypothesized that the exposure of Salmonella Typhimurium to CBD may result in flgA upregulation, causing the bacteria to withstand various stresses and potentially enhance its survival rates and pathogenicity. We have employed several assays, such as mRNA expression, motility assays, pH induction assays, nutrient starvation interventions, and biofilm analysis, to explore the influence of CBD on the pathophysiology of Salmonella Typhimurium. Our findings reveal that CBD-resistant strains exhibit enhanced resilience to extreme pH levels and motility and survive poorly under nutrient starvation, with more robust biofilm formation compared to the susceptible strains. The results contribute to the broader comprehension of CBD resistance mechanisms in bacteria. This work provides insight into the potential therapeutic interventions for controlling CBD-resistant bacterial infections. This study also underscores the essence of exploring novel alternative antimicrobial agents to tackle the ever-persistence of bacterial antibiotic resistance.

The electronic properties of calcium intercalated graphite (CaC6) as a function of pressure are revisited using density functional theory (DFT). The electronic band structures of CaC6, like many other layered superconducting materials, display cosine-shaped bands at or near the Fermi level (FL). Such bands encompass bonding/antibonding information with a strong connection to superconducting properties. Using an hexagonal cell representation for CaC6, construction of a double supercell in the c-direction effects six-folding in reciprocal space of the full cosine function, explicitly revealing the bonding/antibonding relationship divide at the cosine midpoint. Similarly, folding of the Fermi surface (FS) reveals physical phenomena relevant to electronic topological transitions (ETT) with application of pressure. For CaC6, the peak value for the superconducting transition temperature, Tc, occurs at about 7.5 GPa, near to the observed pressure of the calculated ETT. At this pressure, the radius of the nearly spherical Ca 4s-orbital FS coincides with three times the distance from the G centre point to the Brillouin zone (BZ) boundary of the 2c supercell (which is equal to half the identically defined distance for the primitive rhombohedral BZ). In addition, the ETT coincides with alignment of the non-bonding (inflection) point of the cosine band (the point at which the sign of the cosine amplitude modulation is reversed) with the FL. At other calculated pressure conditions, the Ca 4s-orbital FS undergoes topological changes that correspond and can be correlated to experimentally determined changes in Tc. The ETT is a key mechanism that circumscribes the known significant drop in Tc for CaC6 as a function of increasing pressure.

Background: Several kinds of research say that adjuvant blood glucose and blood pressure are usual, but an efficient solution for medical application count remains. This review analyzes the pandemic blood pressure and blood glucose to identify the publications which tell about the clinical practices and research gaps in systematic research.Methods: A study guides to identify the research of Blood Pressure (BP) and Blood Glucose. In order to analyze the recent innovations and research on BP and Blood glucose, the relevant publications and literature from journals were identified.Results: Co-morbidity of BP and Blood glucose is reported as very high. The commonness of blood pressure is thrice as high in type I diabetes patients and almost two times higher in type II diabetes patients when compared to others without Diabetes. The pervasiveness of getting depression is more in the female when compared with men. A detailed study about the linkage of BP and blood glucose tells that the relationship between them is not exactly clear.Limitations: Nearly all reviews providing the linkage of BP and blood glucose are with some limitations and they are not providing any clear conclusion.Conclusions: Present research tells that people having high blood glucose will have a greater chance of getting high blood pressure. More research is needed to state the linkage between BP, blood glucose, and the growth of diabetes mellitus issues and to provide support for managing Diabetes.

Background: This study stands as a pioneer in the histological evaluation of the biological behavior of a novel implant design featuring decompressive cervical blades. Hence, the aim of the present study was to evaluate the healing outcome in cortical regions at where decompressive protocols were adopted using implants equipped with blades. Materials and methods: Blades with varying diameters were integrated into the coronal portion of the implant to prepare the cortical region of rabbit tibiae. The blade diameters differed from the implant collar by the following amounts: control group (0 µm), +50 µm, and +200 µm. Results: No marginal bone loss was detected. Instead, all implants exhibited new bone formation in the coronal region. Complete closure was observed in the CG-0 group, as well as in the TG-50 and TG-200 groups, despite the presence of marginal gaps without primary bone contact at installation. In the apical region, most implants breached the cortical layer. Nevertheless, new bone formation in this region completely closed the osteotomy, effectively isolating the internal environment of the tibia from the external. Conclusions: The use of a blade attached to the implant body enabled precise preparation of the cortical layer, allowing for controlled decompression in the targeted area. This technique resulted in optimal osseointegration with no loss of marginal bone, and complete restoration of marginal gaps ranging from 0 µm to 200 µm.

Due to environmental concerns, natural refrigerants and their use in refrigeration and air conditioning systems are receiving more attention from manufacturers, end users and the scientific community. The study of heat transfer and pressure drop is essential for accurate design and more energy efficient cycles using natural refrigerants. The aim of this work is to provide an overview of the latest outcomes related to heat transfer and pressure drop correlations for ammonia, propane, isobutane and propylene and to investigate the current state of the art in terms of operating conditions. Available data on the existing correlations of heat transfer coefficient and pressure drop for natural refrigerants have been collected through a systematic search. Whenever possible, validity intervals are given for each correlation and the error is quantified. It is the intention of the authors that this could be a valuable support for researchers and an aid to design, with particular reference to heat pumps. A procedure based on the Preferred Reporting Items for Systematic Reviews and Meta-Analyses (PRISMA) statement was adopted, and the Scopus database was used to query the relevant literature. A total of 135 publications qualified for inclusion in the survey; 34 articles report experimental investigations for not usual geometric conditions. Of the 101 selected papers related to usual geometric conditions, N = 50 deal only with HTC, N = 16 deal only with pressure drop and the remainder (N = 35) analyse both HTC and pressure drop. Among the 85 HTC papers (N = 53) deal with the evaporating condition, N = 30 with condensation and only N = 2 with the heat transfer correlations under both conditions. Most of the 101 articles concern propane and isobutane. The high temperatures are less widely investigated.

Medical data flows in streams as the data related to clinical tests and administered drugs by the doctors flows continuously. The doctors must be immediately alerted if negative associations are found among the drugs they prescribe. Data streams are to be processed in single scans as it is not possible to re-scan the data for any iterative processing. To detect negative drug connections, regular and frequent drug patterns must be processed. Negative correlations between disease-curing medications might create adverse responses that kill patients. This paper proposes an algorithm that finds the negative associations among regular and frequent patterns mined from medical data streams. The negative associations mined are the most effective and reduce the negative associations, which are more critical by 50%.

In current transportation hubs, it is a common phenomenon that passengers travel with necessary wheeled-luggage or suitcases. Due to the fact that most luggage occupies certain space within dense passenger crowds with giant mass inertia, its abnormal motions, such as drifting, frequently trig unavoidable local disturbances and turbulence in surrounding pedestrian flows, further increasing security risk. While, current researches primarily concentrate on examining the impact of luggage on crowd evacuation efficiency through scenario-based experiments and analyzing the spatial characteristics of crowd distribution in surveillance videos. There still lacks of the dynamic disturbance mechanisms and crowd stability associated with the combined motion of passengers and luggage. Therefore, this study considers the luggage-laden passenger as a deformable particle, the resulting disturbance on surrounding non-luggage passengers is analyzed and quantified into a nonlinear pressure term. Subsequently, the disturbance propagation model of passenger-luggage is developed by adapting the classical Aw-Rascle traffic flow model with incorporation of the pressure term. Simulation experiments of disturbances caused by luggage drifting and retrograding validate that the proposed propagation model aligns with real-world situations in transportation hubs. Quantitively, when luggage-laden passenger drifted left, the disturbing force of left side crowd can reach a peak of 238N in the passenger density of 3.0 p/m2, and the maximum difference between the left and right sides disturbing force can reach 153N. Furthermore, it is recommended that the proposed model can be applied to crowd flow analysis and risk assessment.

The ethylene-regulated hypocotyl elongation of Arabidopsis thaliana's involves many transcription factors. The specific role of MYC transcription factors in ethylene signal transduction is not completely understood. The results here revealed that two MYCs, MYC2 and MYC3, act as negative regulators in ethylene-suppressed hypocotyl elongation. Etiolated seedlings of the lost-of-function mutant of MYC2 or MYC3 were longer than wild type seedlings. Single- or double-null mutants of MYC2 and MYC3 displayed an enhanced response to ACC(1-aminocyclopropane-1-carboxylate), the ethylene precursor, compared to wild type seedlings. MYC2 and MYC3 directly bind to the promoter zone of ERF1, suppressing its expression. Additionally, EIN3, a key component in ethylene signaling, interacts with MYC2 or MYC3 and suppresses their binding to ERF1’s promoter. MYC2 and MYC3 play crucial roles in the ethylene-regulated expression of functional genes. The results revealed these transcription factors’ novel role and functional mechanism in ethylene signal transduction.

We first explore negative-ion formation in fullerenes C44, C60, C70, C98, C112, C120, C132 and C136 through low-energy electron elastic scattering total cross sections calculations using our Regge-pole methodology. Water oxidation to peroxide and water synthesis from H₂ and O₂ are then investigated using the anionic catalysts C44ˉ to C136ˉ. The fundamental mechanism underlying negative-ion catalysis involves hydrogen bond strength-weakening in the transition state. DFT transition state calculations found C60ˉ numerically stable for both water and peroxide synthesis, C100ˉ increases the energy barrier the most and C136ˉ the most effective catalyst in both water synthesis and oxidation to H2O2.

The present study aims to evaluate the antibacterial activity of five commercially available essential oils (EOs): Lavender (LEO), Clove (CEO), Oregano (OEO), Eucalyptus (EEO), and Peppermint (PEO) against the most-known MDR Gram-positive and Gram-negative bacteria - Staphylococcus aureus (ATCC 25923), Escherichia coli (ATCC 25922) and Pseudomonas aeruginosa (ATCC 27853) - alone and in various combinations. Gas Chromatography-Mass Spectrometry (GC-MS) analysis established their complex composition. Then, the antibacterial activity was investigated in vitro by diffusimetric antibiogram method, using sterile cellulose discs with Ø 6 mm impregnated with 10 µl of sample and sterile borosilicate glass cylinders loaded with 100 µl of sample; MIC (µg/mL) for each EO was calculated from IZD values (mm) measured after 24 hours. The following EO combinations were evaluated: OEO+CEO, CEO+EEO, CEO+PEO, LEO+EEO, and EEO+PEO. Then, the influence of each dual combination on 3 conventional antibacterial drugs – Neomycin (NEO), Tetracycline (TET), and Bacitracin (BAC) - activity was investigated. The most active EOs against S. aureus and E. coli were LEO and OEO (IZD = 40 mm). They were followed by the CEO and EEO (IZD = 20-27 mm); PEO exhibited the lowest antibacterial activity (IZD = 15-20 mm). EEO alone showed the highest inhibitory activity on P. aeruginosa (IZD = 25-35 mm). It was followed by the CEO, LEO, and EEO (IZD = 7-11 mm), while PEO proved no antibacterial action against it (IZD = 0 mm). Only one synergic action was recorded (OEO+CEO against P. aeruginosa); EEO+PEO revealed partial synergism against S. aureus and CEO+PEO additive behavior against E. coli. Two triple associations with TET showed partial synergism against E. coli, and the other 2 ones (with NEO and TET) evidenced the same behavior against S. aureus; all contained EEO+PEO or CEO+PEO. Most combinations reported indifference. However, numerous cases were of antagonism between constituents included in double and triple combinations, and EOs with the strongest antibacterial activities belong to the highest antagonistic combinations. A consistent statistical analysis supports our results, showing that EOs with moderate antibacterial activities could generate combinations with higher inhibitory effects based on synergistic or additive interactions.

The system of non-interacting electrically charged core-massless spring-shell mechanical units, demonstrating negative effective mass, is considered, seen as a Drude-Lorentz gas. When such an ideal gas is exposed to the external harmonic field, it demonstrates as the certain conditions the negative frequency-dependent electrical conductivity. The negative value of the electrical conductivity implies that the electrical current will flow against the direction of the electric field and correspondingly the direction of the electrical force. Low- and high-frequency asymptotic behavior of the electrical conductivity is addressed. The same system demonstrates at low frequencies the negative asymptotic refraction. Experimental realization of the introduced model system, based on the exploitation of plasma oscillations of the free electron gas is suggested.

The nozzle is the key element of the water jet generator for energy conversion. In order to explore the influence of the nozzle diameter on the pressure characteristics of the supercharged pulsed water jet plenum chamber, a supercharged pulsed water jet pressure acquisition system was established, and the Equations of motion and theoretical pressurization ratio equations of the supercharged pulsed water jet generator were established. The pressurization chamber pressure acquisition experiments under different nozzle diameters were carried out. The research results indicate that there is a critical nozzle diameter. When the nozzle diameter is less than the critical diameter, the pressure in the boost chamber is equal to the product of the driving pressure and boost ratio. As the nozzle changes, there is no significant change in the peak pressure and frequency of the boost chamber; When the nozzle diameter is greater than the critical diameter, there is a non-linear relationship between the boost chamber pressure and the driving pressure. As the nozzle diameter gradually increases, the actual boost ratio gradually decreases, and the peak pressure of the boost chamber further decreases. The nozzle diameter can no longer provide a load for the establishment of fluid pressure in the boost chamber. The research results provide a research basis for further controlling the pressure characteristics of the boost pulse water jet.

In the realm of high-pressure vessel simulation, conventional finite element method (FEM) approaches, as per ASME standards, may inadequately predict the behavior of flat surfaces under elevated temperatures. This study challenges the efficacy of shell-type mesh modeling for high-temperature flat plates, demonstrating that the thermal conditions within such high-pressure vessels can induce thermal instability and buckling, not accounted for by traditional FEM methods recommended by ASME. Through comprehensive analytical investigations, we reveal that traditional shell-type meshing techniques, while suitable for certain applications, fail to capture the intricate thermal stresses and deformation patterns inherent in high-temperature flat plate configurations. Our analysis delineates distinct stability regimes governed by key design parameters—including plate thickness, operating temperature, and geometric dimensions—profoundly impacting the structural integrity of heating plates under thermal loading. By elucidating these stability boundaries, this research provides engineers with critical insights necessary for optimizing the design and performance of high-temperature equipment. This includes the design of high-pressure vessels with flat surfaces for heating materials, flanges in high-temperature environments, and fins in heat exchangers across various industries such as oil and gas, pyrolysis, and power plants. The findings presented herein serve as a valuable reference for engineers seeking to comprehend and mitigate instability phenomena in solid mechanics, offering practical guidance for developing robust and reliable high-temperature structures in demanding industrial environments.

This article raise a topic of critical examination of polypropylene, a key polymeric material, and its extensive application within the automotive industry, particularly focusing on the manufacturing of brake fluid reservoirs. The study aims to enhance the understanding of polypropylene's behavior under mechanical stresses through a series of laboratory destruction tests and numerical simulations, emphasizing the Finite Element Method (FEM). A novel aspect of this research is the introduction of the PEAK parameter, a groundbreaking approach designed to assess the material's resilience against varying states of strain, known as triaxiality. This parameter facilitates the identification of critical areas prone to crack initiation, thereby enabling the optimization of component design with a minimized safety margin, which is crucial for cost-effective production. The methodology involves conducting burst tests to locate crack initiation sites, followed by FEM simulations to determine the PEAK threshold value for the Sabic 83MF10 polypropylene material. The study successfully validates the predictive capability of the PEAK parameter, demonstrating a high correlation between simulated results and actual laboratory tests. This validation underscores the potential of the PEAK parameter as a predictive tool for enhancing the reliability and safety of polypropylene automotive components. The research presented in this article contributes significantly to the field of material science and engineering by providing a deeper insight into the mechanical behavior of polypropylene and introducing an effective tool for predicting crack initiation in automotive components. The findings hold promise for advancing the design and manufacturing processes in the automotive industry, with potential applications extending to other sectors.

Triple negative breast cancer (TNBC) is associated with a generally poor prognosis due to its highly aggressive and metastatic nature, lack of targetable receptors, as well as the frequent development of resistance to chemotherapy. We previously reported that AU1, a small molecule developed as an inhibitor of BPTF (bromodomain PHD finger containing transcription factor), was capable of sensitizing preclinical models of triple negative breast cancer to chemotherapy, in part via the promotion of autophagy. In studies reported here, we identify an additional property of this compound, specifically that sensitization is associated with inhibition of the P-glycoprotein efflux pump. In silico molecular docking studies indicate that AU1 binds to active regions of the efflux pump, in a manner consistent with inhibition of pump function. This work identifies a novel chemical structure that can influence multidrug efflux, an established mechanism of drug resistance in triple negative breast cancer, that has not yet been successfully addressed by clinical efforts.

Membrane-based sensors (MePSs) exhibit remarkable precision and sensitivity in detecting pressure changes. MePSs are commonly used to monitor catalytic reactions in solution, generating gas products crucial for signal amplification in bioassays. They also allow catalyst quantification by indirectly measuring the pressure generated by the gaseous products. This is particularly interesting to detect enzymes in biofluids associated with disease onset. To enhance the performance of a MePS, various structural factors influence membrane flexibility and response time, ultimately dictating the device's pressure sensitivity. In this study, we fabricated MePSs using polydimethylsiloxane (PDMS) and investigated how structural modifications affect the Young's modulus (E) and residual stress (σ0) of the membranes. These modifications have a direct impact on the sensors' sensitivity to pressure variations, observed as a function of the volume of the chamber (Σ) or of the mechanical properties of the membrane itself (S). MePSs exhibiting the highest sensitivities were then employed to detect catalyst quantities inducing the dismutation of hydrogen peroxide, producing dioxygen as gaseous product. As a result, catalase enzyme was successfully detected using these optimized MePSs, achieving a remarkable sensitivity of (22.7 ± 1.2) µm/nM and a limit of detection (LoD) of 396 pM.

Objectives: To assess the short-term impact of a single global stretching session on plantar pressures and lumbar range of motion (RoM) over one week in sedentary university students. Design: A randomised controlled trial with two parallel groups. Participants: Sixty-four university students were randomly assigned to a stretching group or control group. The stretching group received a single session of global stretching and the control group remained seated for the same length of time as the stretching session. Main outcome measures: Lumbar RoM and plantar pressures were assessed before, immediately after, 48 hours after, and 7 days after intervention. Results: Group-by-time interaction was significant for lumbar lateral flexion (p = 0.044), right maximal pressure (p = 0.003), left maximal pressure (p = 0.008), right mean pressure (p = 0.025), left mean pressure (p = 0.002), and maximal pressure minus mean pressure in right foot (p = 0.007). The model with plantar pressures showed a significant difference for group-by-time interaction (p = 0.010).Conclusion: Global stretching seems to counteract the ill-effects of prolonged sitting up to seven days with respect to plantar pressure in standing without improving lumbar ROM

One-dimensional chain of core-shell pairs connected by ideal springs enables design of the metamaterial demonstrating the negative effective density and negative specific thermal capacity. We assume that the molar thermal capacity of the reported metamaterial is governed by the Dulong-Petit law in its high temperature limit. The specific thermal capacity depends of the density of the metamaterial; thus, it is expected to be negative, when the effective density of the chain is negative. The range of the frequencies enabling the effect of the negative thermal capacity is established. Dependence of the effective thermal capacity on the exciting frequency for various core/shell mass ratios is elucidated. The effective thermal capacity becomes negative in the vicinity of the local resonance frequency ω0 in the situation when the frequency ω approaches ω0 from above. The effect of the negative effective thermal capacity is expected in metals in the vicinity of the plasma frequency.

The reflectance $R$ of monolayer graphene for the normal incidence of electromagnetic radiation is known to be remarkably defined only by $\pi$ and the fine-structure constant $\alpha$. It is shown in this paper that the reflectance (or the sum of transmittance and absorptance) of monolayer graphene, expressed as a quadratic equation with respect to the fine-structure constant $\alpha$ must unsurprisingly introduce the 2$^\text{nd}$ fine-structure constant $\alpha_2$, as the 2$^\text{nd}$ root of this equation, as well as two $\pi$-like constants for a convex and a saddle surface. It turns out that this 2$^\text{nd}$ fine-structure constant is negative, and the sum of its reciprocal with the reciprocal of the fine-structure constant $\alpha$ is independent of the reflectance value $R$ and remarkably equals $-\pi$. Particular algebraic definition of the fine-structure constant $\alpha^{-1} = 4\pi^3 + \pi^2 + \pi \approx 137.036$, containing the free $\pi$ term and agreeing with the physical definition of this dimensionless constant to the 5$^\text{th}$ significant digit, when introduced to this sum, yields $\alpha_2^{-1} = -4\pi^3 - \pi^2 - 2\pi \approx -140.178$. Assuming universal validity of the physical definition of $\alpha$, $\alpha_2$ defines the negative speed of light in vacuum $c_n$. The average of this speed $c_n$ and the speed of light in vacuum $c$ is in the range of the Fermi velocity ($10^6$ m/s). Furthermore, the 2$^\text{nd}$ negative fine-structure constant $\alpha_2$ alone introduces the imaginary set of base Planck units.

For paramagnetic and elastic materials in the presence of quasi-static magnetic field, there is correspondingly quasi-static magnetic pressure, in contrast to the radiational electromagnetic pressure associated with electromagnetic momentum density. A thermodynamic pressure demagnetization is demonstrated. For the elastic dielectrics in the presence of quasi-static electrical field, its dual effect can be easily obtained by variable transformation.

In our previous papers, we demonstrated that inflammation and aging are the common roots of cancer and Alzheimer’s disease (AD). In both diseases, there is an inhibition of the mitochondria. In cancer, the alkaline intracellular pH (pHi) is associated with cell proliferation; acidic pHi causes apoptosis in AD. This difference is because cancer feeds on chemically neutral glucose, while neurons feed on acidic lactic acid. Increased uptake of lactic acid is responsible for acidic pH and cell death. Similarly, to AD, inflammation is responsible for metabolic shifts in age-related macular degeneration (AMD). In AD, there is hyperosmolarity responsible for increased lactic secretion by glial cells. Increased lactic secretion will cause neo-angiogenesis and neural cell death. Drugs increasing hyperosmolarity (Polyethylene Glycol) cause neo-angiogenesis and drusen-like structures in rodents. The link between AMD and inflammation is reinforced by the fact that treatments aiming at restoring mitochondrial activity, such as lipoic acid and/or methylene blue, have been experimentally shown to be effective in each set of diseases. The role of osmolarity has been demonstrated in the pathologies of the anterior segment of the eye, such as dry eye, corneal ulceration, cataracts, and glaucoma. The role of increased osmolarity in age-related macular degeneration (AMD) has been largely overlooked. We herein suggest that metabolic shift, inflammation, and hyperosmolarity are key players in the pathogenesis of AMD.

We provide a detailed analysis of the electronic properties of graphene-like materials with charge carriers living on a curved substrate, focusing in particular on constant negative-curvature spacetime. An explicit parametrization is also worked out in the remarkable case of Beltrami geometry, with an analytic solution for the pseudoparticles modes living on the curved bidimensional surface. We will then exploit the correspondent massless Dirac description, to determine how it affects the sample local density of states.

We report the negative effective mass metamaterials based on the electro-mechanical coupling exploiting plasma oscillations of a free electron gas. The negative mass appears as a result of vibration of a metallic particle with a frequency of ω which is close the frequency of the plasma oscillations of the electron gas m_2 relatively to the ionic lattice m_1. The plasma oscillations are represented with the elastic spring k_2=ω_p^2 m_2, where ω_p is the plasma frequency. Thus, the metallic particle vibrated with the external frequency ω is described by the effective mass m_eff=m_1+(m_2 ω_p^2)/(ω_p^2-ω^2 ) , which is negative when the frequency ω approaches ω_p from above. The idea is exemplified with two conducting metals, namely Au and Li.

High pressure crystallization technique has been successfully used to prepare an elusive form II of a non-steroidal anti-inflammatory drug, Mefenamic acid. Single crystal of form II was grown at 0.3 GPa from an 4:1 methanol/ ethanol mixture as a solvent using Diamond Anvil Cell. Comparison of crystal structures show that the efficient packing of MA molecules in Form II results from the structural flexibility of MA acid molecules. Compression studies performed on the single crystal of form I resulted in 14 % decrease of unit cell volume up to 2.5 GPa. No phase transition was observed up to this pressure. A reconstructive phase transition is required to induce conformational changes in the structure, which is confirmed by crystallization at high pressure results.

This cross-sectional study evaluated the validity of three alternative methods compared to the gold standard 24-h urine collection for estimating dietary sodium intake, a modifiable risk factor for hypertension, among middle-aged and older adults with elevated blood pressure. These included spot urine collection (using Kawasaki, Tanaka, and INTERSALT equations), 24-h dietary recall, and food frequency questionnaire responses, compared against 24-h urine collection in a subset of 65 participants (aged 50–75 years, 58.5 % women, 61.6 % hypertensive) from the DePEC-Nutrition trial. The validity of the methods was assessed using bias, Spearman correlation coefficient (SCC), intraclass correlation coefficient (ICC), and Bland-Altman analysis. Among the alternative methods, spot urine collection using the Kawasaki equation showed the strongest correlation (SCC 0.238; ICC 0.119, 95 % CI -0.079 to 0.323) but it exhibited a significant bias (1414 mg/day, p-value < 0.001) relative to 24-h urine collection. Conversely, dietary surveys had a smaller bias but wider limits of agreement. These findings underscore the complexities of accurately estimating dietary sodium intake using spot urine collection or dietary surveys in this specific population, suggesting that a combination or refinement of existing methodologies might improve accuracy. Further research with larger samples is necessary to develop more reliable methods for assessing sodium intake in this high-risk group.

Background: Extracellular Vesicles are pivotal mediators in intercellular communication, facilitating the exchange of biological information among healthy, pathological and tumor cells. Between the diverse subtypes of extracellular vesicles, exosomes have unique properties, clinical and therapeutical applications, even towards cancer. Breast cancer ranks as one of the most prevalent malignancies across the globe. Both the tumor core and its surrounding microenvironment engage in a complex, orchestrated interaction that facilitates the cancer’s growth and spread. Methods: The most valuable and significant PubMed Literature about extracellular vesicles and adipose–derived stem cells exosomes was selected and analyzed in order to report their biological properties and potential applications, in particular on the Triple–Negative Breast Cancer. Results: Adipose–derived stem cells exosomes represent a potential tool to target the tumor core of the Triple–Negative Breast Cancer, its microenvironment and surrounding tissues including metastasis. The authors are developing a supportive Triple–Adipose–derived stem cells Exosomes [T.A.E.] Technology against breast cancer in order to perform a selective preconditioning of the cancer before or while the traditional oncological treatments are running. Conclusion: The possibility to exploit the impact of Adipose–derived stem cells exosomes within the T.A.E. Technology against the Triple–Negative breast cancer is real, highlighting a new era for supportive measures against breast cancer.Keywords: Extracellular vesicles; Exosomes; Adipose–derived stem cells, Tumor microenvironment, Triple–Negative Breast Cancer, T.A.E. Technology.

There is limited real-world data from India examining the treatment characteristics, safety, and efficacy of ceftazidime-avibactam against Gram-negative organisms especially multidrug-resistant pathogens including Carbapenem-Resistant Enterobacterales and Carbapenem-Resistant Pseudomonas. In this retrospective study, the real-world treatment patterns, effectiveness, and safety of ceftazidime-avibactam in treating Gram- negative infections were assessed. Data was extracted from electronic health records of adult patients admitted to the hospital with documented Gram-negative infection who had received treatment for at least 48 hours with ceftazidime-avibactam as a part of routine clinical management. Among the 189 patients, on day 3, clinical symptoms improvement was recorded in 79.6% of patients. Clinical success was achieved in 79.5% and 76.3% of assessed patients on day 7 and day 14/End-of-treatment, respectively. Microbiological success was reported in 76% of patients on day 7 and in 60.3% of patients on day 14 or EOT. The mean treatment duration of ceftazidime-avibactam therapy was 6.92 (± 4.1) days. No new safety concerns were identified. In conclusion, this study provides real-world evidence on treatment patterns and clinical outcomes associated with ceftazidime-avibactam in India, complementing the previously reported literature. The results suggest ceftazidime-avibactam is an effective and tolerable option for the management of Gram-negative infections in critically ill patients.

High systolic blood pressure and increased blood pressure variability after the onset of ischemic stroke are associated with poor clinical outcomes. One of the key determinants of blood pressure is arteriolar size, determined by vascular smooth muscle tone and vasodilatory and vasoconstrictor substances that are released by the endothelium. The aim of this study is to outline alterations in vasomotor function in isolated peripheral arteries following ischemic stroke. The reactivity of thoracic aortic segments from male C57BL/6 mice to dilators and constrictors was quantified using wire myography. Acetylcholine induced endothelium-dependent vasodilation was impaired after ischemic stroke (LogIC50 Sham=-7.499, LogIC50 Stroke=-7.350, P=0.0132, n= 19, 31 respectively). Vasodilatory responses to SNP were identical in isolated aortas in sham and stroke groups. Phenylephrine induced vasoconstriction was impaired in aortas isolated from stroke animals in comparison to sham counterparts (Sham LogEC50= -6.652 vs Stroke LogEC50=-6.475, P< 0.001). Our study demonstrates that 24 hours post-ischemic stroke, peripheral vascular responses are impaired in remote arteries. Aortas from stroke animals exhibited reduced vasoconstrictor and endothelium-dependent vasodilator responses, while endothelium-independent vasodilatory responses were preserved. Since both vasodilatory and vasoconstrictor responses of peripheral arteries are impaired following ischemic stroke, our findings might explain increased blood pressure variability following ischemic stroke.

The paper will analyze the pressures and vulnerabilities of the consolidated city from two perspectives: technical and social. Some design and pragmatic experiences conducted by the author in his teaching and research experience first at the Department of Urbanism of TUDelft in the Netherlands and currently at the PDTA Department of La Sapienza University of Rome will be introduced and analyzed. In the first research activity, whose case study is Rotterdam, all urban vulnerabilities related to climate change will be analyzed while in the second one, conducted in Viterbo, the vulnerability related to the hull of social inclusion, poor accessibility and psycho-social stress that plague our established cities will be treated. The two areas of study, different in size and spatial governance tools, are comparable because they allow deciphering the city's risks through lines of intervention that could serve as best practices and serve the urban planning disciplinary update also allowing to define a reflection on morphology and fabrics and on the shape of the city itself. Both teaching and research activities in which the author is involved allow the topic of urban vulnerability to be addressed with a broad exploratory scope that, in the final stage, hypothesizes design intervention on the neighborhood scale, identified as the most appropriate to provide plausible climate and social adaptation and mitigation responses.

Pressure-sensitive paint (PSP) has received significant attention for capturing surface pressure in recent years. One major source of uncertainty in PSP measurements, temperature dependency, stems from the fundamental photophysical process that allows PSP to extract pressure information. The motion-capturing PSP method, which involves two luminophores, is introduced as a method to reduce the measurement uncertainty due to temperature dependency. A theoretical model for the pressure uncertainty due to temperature dependency is proposed and demonstrated using a static pressure measurement with an applied temperature gradient. The experimental validation of the proposed model shows that the motion-capturing PSP method reduces the temperature dependency by 37.7% compared to the conventional PSP method. The proposed model also proves that a PSP with zero temperature dependency is theoretically possible.

Triple negative breast cancer (TNBC) has a negative expression of estrogen receptors (ER), progesterone receptors (PR), or human epidermal growth factor receptors (HER2). The survival rate for TNBC is generally worse than other breast cancer subtypes. TNBC treatment has made significant advances, but certain limitations remain. Treatment for TNBC can be challenging since the disease has various subtypes. Individualized therapy is recommended rather than generalized therapy, given the genetic variations among these TNBC subtypes. A precise and effective treatment for TNBC requires identifying prognostic markers. Depending on the type and stage of TNBC, patients are treated with various therapeutic interventions. A variety of treatment options are available, such as chemotherapy, immunotherapy, radiotherapy, and surgery. Chemotherapy is the most common of these options. TNBC is generally treated with systemic chemotherapy using drugs such as anthracyclines and taxanes in the neoadjuvant or adjuvant settings. Developing resistance to anticancer drugs and off target toxicity are the primary hindrances to chemotherapeutic solutions for cancer. It is imperative that researchers, clinicians, and pharmaceutical companies work together to develop effective treatment options for TNBC. Several studies have suggested nanotechnology as a potential solution to the problem of suboptimal TNBC treatment.

The implementation of green logistics can reduce the increasingly serious environmental damage and improve the operating efficiency of logistics enterprises. In this paper, through quantitative calculation of logistics negative external costs, including traffic accidents, atmospheric pollution, noise pollution, and pollution caused by packaging, we build accounting standards to calculate the negative external cost of logistics enterprises that mainly generate pollution from transportation and packaging. Then, assuming the impetus provided by government implementing incentive mechanisms in a free market economy, we establish a ‘Logistics Negative External Cost Internalizing’ model, which quantitatively analyzes the relationships among freight rate, freight volume, investment of enterprise for implementing green logistics, and the subsidy given by government, under the comparison of the two modes ‘enterprise operates first’ and ‘government subsidizes first’. The results show that the introduction of ‘government subsidizes first’ incentive mechanism and increasing freight rate are helpful in promoting the process of logistics market greening.

Background Homologous recombination deficiency (HRD) evolved into a major diagnostic marker in high grade ovarian cancer (HGOC) predicting the response to poly (Adenosine diphosphate-ribose) polymerase inhibitors (PARPi) and also platinum-based therapy. In addition to HRD, the type of peritoneal tumor spread influences treatment response and patient survival; miliary type tumor spread has poorer predicted outcome than non-miliary type tumor spread. Methods Known methods for HRD assessment were adapted for our technical requirements and the Predictive-value Integrated Genomic Instability Score (PIGIS) for HRD assessment evolved as an outcome. PIGIS was validated in HGOC samples from 122 patients. We used PIGIS to analyze whether the type of tumor spread correlated with HRD status and whether this had an impact on survival. Results We demonstrated that PIGIS can discriminate HRD positive from HRD negative samples. Tumors with miliary tumor spread are HRD negative and have a very bad prognosis with a progression free survival (PFS) of 15.6 months and an overall survival (OS) of 3.9 years. However, HRD negative non-miliary spreading tumors in our cohort had a much better prognosis (PFS 35.4 months, OS 8.9 years), similar to HRD positive tumors (PFS 34.7 months, OS 8.9 years). Conclusions Our results indicate that in a predominantly PARPi naïve cohort the type of tumor spread might be a better predictor of response to platinum sensitivity than HRD. It remains to be determined, whether this also applies for sensitivity to PARPi.

This research has developed a process for producing ZnO thin film from DEZn deposited onto a PET substrate with low-pressure, high-frequency Ar + O2 plasma using a chemical vapor deposition technique. The aim is to study the film production conditions that affect electrical properties, optical properties, and thin film surfaces. This work highlights the use of plasma energy produced from a mixture of gases between Ar + O2. Plasma production is stimulated with an RF power supply to deliver high chemical energy and push ZnO atoms from the cathode inside the reactor onto the substrate through surface chemical reactions. The results showed that increasing the RF power in plasma production affected the chemical reactions on the substrate surface of film formation. The film preparation at RF power 300 W will give the thickest films. The film has a continuous columnar formation, and the surface has a granular structure. This results in the lowest electrical resistivity of 1.8 x 10-4 Ω-cm. In addition, when fabricated into a DSSC device, the device tested the PCE value and showed the highest value at 5.68%. This is due to the very rough surface nature of the ZnO film, which increases the scattering and storage of sunlight, making cells more efficient. Therefore, the benefit of this research is that it will be a highly efficient prototype of thin film production technology using a chemical process that reduces production costs and can be used in the industrial development of solar cells.

Controlling injection parameters is paramount when it comes to producing high-quality green parts using powder injection molding. This work combines experimental and numerical approaches to study the impact of injection parameters on mold in-cavity pressure and on the overall quality of green parts produced by low-pressure powder injection molding. The properties of two low-viscosity feedstocks (formulated from a water-atomized stainless-steel powder and wax-based binder system) were measured and implemented in an Autodesk Moldflow numerical model to quantify the molding pressures, which were finally validated using experimental real-scale injections. The results confirmed that an increase in mold temperature, an increase in feedstock temperature, and a decrease in solid loading decrease the mold in-cavity pressure, which was correlated with the feedstock viscosity. As a key result, real-scale injections confirmed that a minimum flow rate was required to avoid atypical high in-cavity pressure leading in several visual defects such as weld lines, flow marks, cracks, sinks, and incomplete filling. Due to differences in its thermal transfer properties, this flow rate threshold value decreases as the feedstock solid loading increases. For injection speeds higher than this value, the injection pressure measured experimentally was linearly correlated with the injection flow rate.

Abstract: Coal bed methane (CBM) reservoirs are complex systems whose properties differ from those of conventional reservoirs. Coal seams are dual-porosity systems that comprise the porosities of the matrix and cleat system. Gas in the coal seams can be stored as free gas in the cleat system and as adsorbed gas in the porous medium. The flow mechanisms of the natural gas through the formation include desorption, diffusion, and Darcy’s flow regimes. The permeability of CBM reservoirs is more sensitive to pressure variations than conventional gas reservoirs. To study the flow behavior of CBM reservoirs it is mandatory to use a model that considers their unique characteristics. The objective of this study was to propose a physical and mathematical model of production performance for horizontal wells in CBM reservoirs whose permeability is dependent on pressure. A solution for the model was obtained by applying Pedrosa´s transformation, perturbation theory, Laplace transformation, the point source method, and Sthefest´s algorithm. The solution to this problem was validated with previous work thoroughly. The type curves of the model were built and the pressure transient behavior of the model was analyzed and discussed. The effects of several parameters on pressure behavior were also discussed.

Chronic exposure to the nephrotoxic metal pollutant, cadmium (Cd), has been associated with hypertension, but the mechanism by which it raises blood pressure is not understood. We hypothesize that exposure to Cd reduces the glomerular filtration rate (GFR), which in turn, causes a rise in blood pressure. Data were collected from 447 Thai subjects with a mean age of 51.1 years, of which 48.8% had hypertension, 15.4% had diabetes and 6.9% had an estimated GFR (eGFR) below 60 mL/min/1.73 m2 (low eGFR). The mean blood and urinary Cd concentrations were 2.75 and 4.23 µg/L, respectively. The prevalence odds ratio (POR) for hypertension rose twofold in those with blood Cd levels of 0.61-1.69 µg/L or urinary Cd excretion levels ≥ 0.98 µg/g creatinine. In the hypertensive group, the eGFR was inversely associated with age (β =−0.517), the Cd excretion rate (β = −0.177), and diabetes (β = −0.175). Mean eGFR in the normotensive group was 7.5 mL/min/1.73 m2 higher than the hypertensive with a similar Cd body burden. Mean systolic blood pressure (SBP) in those with low or medium eGFR plus heavy Cd body burden was 9.5 mmHg higher than those with the same Cd body burden and a normal eGFR. By mediation analysis, a 22.7% increase in SBP and a 5% increase in diastolic blood pressure (DBP) were attributable to the effect of Cd on GFR. Thus, a rise of blood pressure appears to be a consequence of GFR loss due to Cd-induced kidney damage. This finding is consistent with a well-known role of the kidney in long-term blood pressure regulation.

Headache is considered to be one of the most common causes of medical treatment and evaluation worldwide in both acute and outpatient settings. It is the most common neurological symptom seen worldwide affecting all genders, ages, ethnicities, and socioeconomic levels. It’s impact is noted in educational decline in school-aged children and decreased productivity through sick leave in adults. Its overall burden is well documented in well-resourced countries but limited data is seen low resourced countries. While many underlying causes bring about secondary headaches, primary headaches and more specifically migraines have been more widely explored. Migraines have a distinct criterion that is inclusive of one day duration (4 hours to 7 days, unilateral distribution, nausea and vomiting and disability as a few examples. However, migraines can vary and proper documentation through a migraine diary can help to guide treatment. Management of migraines can vary. Lifestyle modification is a key factor in the overall prevention and reduction of triggers in migraines. In addition to this, pharmacotherapy can be given in a tier-based approach based on overall severity and frequency of the migraine. Interventions have progressed from botox injection and have seen the advent of new medications such as nasal sprays to novel formulations of pre-existing drug formulations. Nonetheless, there is great room for further studies of headaches and migraines. Research specifically in low-resource countries can prove to beneficial.

Pressure Ulcers (PU) are a debilitating and often painful condition. They are localized lesions on the skin and/or underlying tissues and are common in the elderly, immobile people, diabetics and vascular disease or malnutrition, as well as in those requiring intensive or palliative care. Prevention and treatment of PU involve strategies to optimize hydration, circulation and nutrition. Nutrition plays a key role in pressure ulcer care because wounds require macronutrients and micronutrients to heal. Reports relating to the effectiveness of "Complementary Enzyme Therapy" also in the vulnological field led us to this study, the aim of which was to test the activity of a biodynamic nutritional supplement (Citozym®), characterized by a marked antioxidant activity, administered topically and/or systemically, in patients suffering from PU. The treatment showed a marked reduction in bedsores and in many cases their complete healing. Furthermore, it was possible to observe a lower incidence of side effects compared to conventional therapies. The results obtained, confirmed by various tests, and recognized by the scientific community, allow us to conclude that treatment with Citozym® could represent a new and effective strategy for the treatment of PU.

The antimicrobial quantitative structure–activity relationship of plant flavonoids against Gram-positive bacteria was established in our previous works, and the cell membrane was confirmed as a major site of action. To investigate whether plant flavonoids have similar antibacterial effects and mechanisms against both Gram-negative and Gram-positive bacteria, here, the minimum inhibitory concentrations (MICs) of 37 plant flavonoids against Escherichia coli were determined using the microdilution broth method, and then the correlation between their lipophilic parameter ACD/LogP or LogD_7.40 value and their MIC was analyzed. Simultaneously, the correlation between the ACD/LogP or LogD_7.40 value and the MIC of 46 plant flavonoids reported in literature against E. coli was also analyzed. Both sets of results showed that there is a significant correlation between the LogP value and the MIC of plant flavonoids against Gram-negative bacteria. However, it is difficult to effectively predict the MIC of plant flavonoids against Gram-negative bacteria from their lipophilic parameters. By comparing two regression curves derived from plant flavonoids against Gram-negative and Gram-positive bacteria, it was further discovered that the antibacterial activities of most plant flavonoids against Gram-negative bacteria are stronger than those against Gram-positive bacteria when their LogP values are less than about 3.0, but the opposite is true when their LogP values are more than about 3.6. Moreover, this comparison also suggests that unlike mainly acting on the cell membrane of Gram-positive bacteria, plant flavonoids have multiple mechanisms against Gram-negative species, while the cell membrane is also an important action site among them. Combined with the correlation analyses between the enzyme inhibitory activity and the LogP value of the reported flavonoids, it was further suggested that DNA gyrase is another important target of plant flavonoids against Gram-negative bacteria.

Triple negative breast cancer (TNBC) has a higher mRNA expression of programmed cell death ligand 1 (PD-L1) which is a ligand to programmed cell death protein 1 (PD-1). The binding of the ligand leads to suppressed activity of T-cell-mediated immune response against cancer cells. The approval of anti-PD-L1 drugs including pembrolizumab and atezolizumab in subgroups of TNBC offer potential improvement to the current treatment regimens available for TNBC. We conducted a meta-analysis to review the efficacy of pembrolizumab and atezolizumab for the treatment of TNBC in both adjuvant and neo-adjuvant settings. A systematic strategy was used as per the PRISMA 2020 statement. All statistical analyses were conducted using Review Manager 5.4. Outcome measures included objective response rate, progression free survival, overall survival in adjuvant therapy groups, and pathological complete response rates in neoadjuvant groups. Six clinical trials were included. For adjuvant therapies, the ORR (OR=1.26, P = 0.04) of Atezolizumab/Pembrolizumab plus chemotherapy was higher in intention to treat (ITT) arms than the placebo groups in TNBC. A positive effect size was found for PFS in the ITT arms (Cohen’s d = 1.55, P<0.001). The Atezolizumab plus chemotherapy group had a positive effect size for OS compared to the control groups (Cohen’s d = 0.52, P<0.001). In the neo-adjuvant setting, patients in ITT arms had higher pCR rates as compared to the control groups (OR= 1.61, P = 0.001). Our findings collate evidence of pembrolizumab and atezolizumab as a viable treatment option among patients with TNBC with PDL1+ subgroups deriving benefits.

The structural stability of γ-boron is investigated using Raman spectra under high pressures up to 126 GPa at ambient temperature. The pressure dependence of all the Raman-active modes of the γ-boron is reported. We also observe amusing changes within the B3g and B1g Raman-active vibrational modes, which results in the phenomenon of merging first and then separating of the Raman peaks. In addition to the Raman measurements, the changes in crystal structure and force constants are calculated to reasonably explain the discrepancy between the two Raman modes in response to pressure. The results of the continuous shifts for all Raman modes with increasing pressure indicate that γ-boron remains stable below this pressure value, with no changes in either symmetry or structure.

Based on the nonlinear failure criterion and modified tangential technique, the upper bound solutions of supporting pressure on the deep tunnel face were obtained under pore water pressure conditions. The influence of parameters on the supporting pressure and collapse range was investigated according to the unlimited block failure mechanism. It is found that the upper bound solutions of supporting pressure increase with the growth of the nonlinear coefficient and pore water pressure coefficient. The collapse range of the tunnel face scales out with the increase of the nonlinear coefficient and shrinks when increasing the pore water pressure coefficient. Moreover, with the increase of the nonlinear coefficient, the impact strength on supporting pressure and collapse range declines gradually. According to the calculating results, it is manifest that both the pore water pressure and nonlinear criterion factors have negative impacts on the stability of the tunnel face. Thus, more attention should be paid to these parameters to ensure face stability in deep tunnel construction.

It has been suggested that the measured magnetic properties of hydrides under pressure claimed to be high temperature superconductors indicate that the materials are granular superconductors. Such materials will show reduced or no magnetic field expulsion under field cooling, and will trap magnetic fields when the external magnetic field is removed. They will also exhibit hysteretic behavior in magnetoresistance and other transport properties. Here we point out that hysteresis in transport properties has never been reported for hydrides under pressure. Its presence, with the expected features, would indicate that the materials trap magnetic flux, hence that they can sustain persistent currents without dissipation, something that all superconductors can do. Conversely, its absence would indicate that these materials are not superconductors.

Glucosamine is the most common nutrition supplement used in the United States. It is promoted not only as a pain reliever but also a therapy to slow osteoarthritis. Although studies with 3,800 patients with osteoarthritis of the knee or hip found that glucosamine was no better than placebo, it continues to be used for these two indications due to its perceived safety. However, reports of an increased intraocular pressure are alarming, especially in glaucoma. Glycosaminoglycans play a key role in the physiology of the cornea, conventional outflow of aqueous humor and the retina. In theory, long-term treatment with glucosamine could reach a concentration that impacts the morphology and function of ocular tissues. We recommend ophthalmologists counsel glaucoma patients about the potential risks of glucosamine and encourage cessation in uncontrolled intraocular pressure.

The pressure exerted on the heart and blood vessels because of blood flow is considered as an important parameter for the cardiovascular function. It determines sufficient blood perfusion as well as transportation of nutrition, oxygen and other essential factors to every organ. Pressure in the primary arteries located near the heart and the brain, known as central blood pressure (CBP), while in peripheral arteries, known as peripheral blood pressure (PBP). Normally, CBP and PBP are correlated; however, cardiovascular disorders interfere their regulation and affect the blood flow in vital organs and accessory organs, differently. Therefore, understanding each of them in normal and disease conditions is essential for managing various cardiovascular disorders and increasing their treatment outcomes. In this review, we have described the control systems (neural, hormonal, osmotic and cellular) of the blood pressure and its regulation in hypovolemic shock using centhaquine (Lyfaquin®) as a resuscitative agent.

The effect of the negative effective mass emerging in the gravitating core-spring-shell system is considered. The effect appears when the entire system is exerted to the external harmonic force and the frequency of external force approaches to the critical frequency from above. The critical frequency depends on the density of the self-gravitating system only. The scaling law predicting the value of for condensed phases is derived. The generalization of the effect for the Coulomb-like forces is reported

This study investigated the associations of imageability with fear reactivity. Imageability ratings of four word classes: positive and negative (i) emotional and (ii) propriosensitive, neutral and negative (iii) theoretical and (iv) neutral concrete filler, and fear reactivity scores – degree of fearfulness towards different situations (TF score) and total number of extreme fears and phobias (EF score), were obtained from 171 participants. Correlations between imageability, TF and EF scores were tested to analyze how word categories and their valence were associated with fear reactivity. Imageability ratings were submitted to recursive partitioning. Participants with high TF and EF scores had higher imageability for negative emotional and negative theoretical words. The correlations between imageability of negative emotional words and negative theoretical words for EF score were significant. Males showed stronger correlations for imageability of negative emotional words for EF and TF scores. High imageability for positive emotional words was associated with lower fear reactivity in females. These findings were discussed with regard to negative attentional bias theory of anxiety, influence on emotional systems, and gender-specific coping styles. This study provides insight into cognitive functions involved in mental imagery, semantic competence for mental imagery in relation to fear reactivity, and a potential psycholinguistic instrument assessing fear tendency.

Blood stream infections (BSI) due to carbapenem-resistant gram-negative bacilli (CR-GNB), especially Klebsiella pneumoniae carbapenemase (KPC) and New-Delhi metallo-β-lactamase (NDM) producers, are a major concern of public health, as they are associated with high morbidity and mortality. We conducted a single-center, retrospective, observational study at a tertiary-care, teaching Greek hospital, to determine the incidence, 30-day and overall, in-hospital, crude mortality, risk factors and efficacy of best available treatment options in patients with BSIs from KPC- or NDM-producing GR-GNB. During the one-year study period, from 1st January to 31st December 2023, we recorded 133 episodes of BSIs in 118 unique patients; 79 episodes were due to KPC-producing and 54 to NDM-producing CR-GNB. Our study showed relatively high incidence of BSIs by both KPC- and NDM-producing CR-GNB (0.49 and 0.31 episodes per 1000 patient-days respectively). We found high 30-day crude mortality rates for patients with BSIs due to KPC- producing CR-GNB (26.4 %), and NDM-producing CR-GNB (37%), while BSIs due to NDM-producing P. aeruginosa had the highest 30-day (47.1%) and overall (70.6%) in-hospital, crude mortality. Beta-lactam/beta-lactamase inhibitors as monotherapy or in combination with other active agents used to treat KPC-producing CR-GNB were associated with improved survival rates (p=0.009).

In the investment casting process, the pattern made of wax is obtained in a die for further formation of shell mold. This work investigates commercial pattern waxes fluidity with a newly developed injection fluidity test. A good correlation between wax fluidity and its viscosity is observed, which is different from metallic alloys, where the solidification behavior is more critical. The difference in investigated filled waxes fluidity can be associated with the type and amount of filler.

Background: Epileptic patients frequently encounter cognitive impairment. Functions that are mostly affected involve memory, attention and executive function; however this is mainly dependant on the location of the epileptic activity. The aim of the study is to assess cognitive functions in MRI-negative epilepsy patients by means of neurophysiological and neuropsychological measures. Methods: The patients were enrolled from the outpatient Epilepsy/Clinical Neurophysiology clinic over a time period of 6 months. The study sample comprised 20 MRI negative epilepsy patients [mean age ± standard deviation (SD), 30.3 ± 12.56 years; age range 16-60 years; average disease duration, 13.95 years) and 10 age-matched controls (mean age ± SD, 24.22 ± 15.39 years), that were also education-matched (p>0.05) Patients with epileptogenic lesions were excluded from the study. Informed consent was obtained from all subjects involved in the study. Auditory ERPs and the cognitive screening tool EpiTrack, were administered to all subjects. Results: Latencies of P300 and slow waves were prolonged in patients compared to controls (p<0.05). ASM load and the patients’ performance in the EpiTrack maze subtest were the most significant predictors of P300 latency. A decline in memory, attention, and speed of information processing has been observed in patients with cryptogenic epilepsy compared to age-matched controls, as reflected by P300 latency and EpiTrack scores.

Antimicrobial resistance has become a significant public health problem globally with multidrug resistant Gram negative (MDR-GN) bacteria being the main representatives. The emergence of these pathogens in neonatal settings threatens the well-being of vulnerable neonatal population given the dearth of safe and effective therapeutic options. Evidence from studies mainly in adults is now available for several novel antimicrobial compounds, such as new β-lactam/β-lactamase inhibitors (e.g. ceftazidime-avibactam, meropenem-vaborbactam, imipenem/cilastatin-relebactam), although old antibiotics such as colistin, tigecyclin and fosfomycin are also encombassed in the fight against MDR-GN infections that remain challenging. Data in the neonatal population are scarse, with few clinical trials enrolling neonates for the evaluation of efficacy, safety and dosing of new antibiotics, while the majority of old antibiotics are used off-label. In this article we review data about some novel and old antibiotics that are active against MDR-GN bacteria causing sepsis and are of interest to be used in the neonatal population.

Triple-negative breast cancer (TNBC) is a subtype of breast cancer characterized by the lack of estrogen receptors (ER), progesterone receptors, and HER-2 receptors. Thus, TNBC tumours do not benefit from the current therapies targeting ER or HER-2. Therefore, there is an urgent need to develop novel treatment for this subtype of breast cancer. Marijuana is a common name given to Cannabis plants, a group of plants in the Cannabis genus of the Cannabaceae family. Cannabis plants are among the oldest cultivated crops, traced back at least 12,000 years and are well known for their multi-purpose usage, including medicinal purposes. The main active compounds extracted from Cannabis plants are 21-carbon-containing terpenophenolics, which are referred to as phytocannabinoids. Of these, the tetrahydrocannabinol (THC) group contains highly potent cannabinoids, including delta-9-tetrahydrocannabinol (∆9-THC) and delta-8-tetrahydrocannabinol (∆8-THC), which are the most abundant THCs and are largely responsible for psychological and physiological effects of marijuana. The use of Cannabis plants for medicinal purposes was first recorded in 2337 BC in China, where Cannabis plants were used to treat pains, rheumatism, and gout. Recently, several cannabinoids have been approved for a number of treatments, one of which is the treatment of nausea and vomiting caused by chemotherapy in cancer patients. Furthermore, increasing evidence shows that cannabinoids not only attenuate side effects due to cancer treatment, but might also potentially possess direct antitumor effects in several cancer types, including breast cancer. However, anti-tumour activity of marijuana has been variable in different studies and even promoted tumour growth in some cases. In addition, the mechanisms of cannabinoid action in cancer remain unclear. This review summarizes evidence about the mixed actions of cannabinoids in cancer in general and triple-negative breast cancer in particular.

Triple negative breast cancer (TNBC) is an aggressive subtype of the disease with poor clinical outcomes and limited therapeutic options. Immune checkpoint blockade (CP) has surged to the forefront of cancer therapies with widespread clinical success in a variety of cancer types. However, the percentage of TNBC patients that benefit from CP as a monotherapy is low and clinical trials have shown the need for combined therapeutic modalities. Specifically, there has been interest in combining CP therapy with radiation therapy where clinical studies primarily with external beam have suggested their therapeutic synergy, contributing to the development of anti-tumor immunity. Here, we have developed a therapeutic platform combining radionuclide therapy (RT) and immunotherapy utilizing a radiolabelled biomolecule and CP in an E0771 murine TNBC tumor model. Survival studies show that while neither monotherapy is able to improve therapeutic outcomes, the combination of RT + CP extended overall survival. Histologic analysis showed that RT + CP increased necrotic tissue within the tumor and decreased levels of F4/80+ macrophages. Flow cytometry analysis of the peripheral blood also showed that RT + CP suppressed macrophages and myeloid-derived suppressive cells, both of which actively contribute to immune escape and tumor relapse.

Sepsis is a life-threatening condition caused by the body's overwhelming response to an infection, such as pneumonia or urinary tract infection. It occurs when the immune system releases cytokines into the bloodstream, triggering widespread inflammation. If not treated, it can lead to organ failure and death. Unfortunately, sepsis has a high mortality rate, with studies reporting rates ranging from 20% to over 50%, depending on the severity and promptness of treatment. According to the World Health Organization (WHO), the annual death toll in the world is about 11 million. One of the main toxins responsible for inflammation induction are lipopolysaccharides (LPS, endotoxin) from Gram-negative bacteria, which ranks among the most potent immunostimulants found in nature. Antibiotics are consistently prescribed as a part of anti-sepsis-therapy. However, antibiotic therapy (i) is increasingly ineffective due to resistance development and (ii) most antibiotics are unable to bind and neutralize LPS, a prerequisite to inhibit the interaction of endotoxin with its cellular receptor complex, namely Toll-like receptor 4 (TLR4)/MD-2, responsible for the intracellular cascade leading to pro-inflammatory cytokine secretion. The pandemic virus SARS-CoV-2 has infected hundreds of millions of humans worldwide since its emergence in 2019. The COVID-19 (Coronavirus disease-19) caused by this virus is associated with high lethality, particularly for elderly and immunocompromised people. As of August 2023, nearly 7 million deaths were reported worldwide due to this disease. According to some reported studies, upregulation of TLR4 and the subsequent inflammatory signaling detected in COVID-19 patients “mimics bacterial sepsis”. Furthermore, the immune response to SARS-CoV-2 was described by others as “mirror image of sepsis”. Similarly, the cytokine profile in sera from severe COVID-19 patients was very similar to those suffering from the acute respiratory distress syndrome (ARDS) and sepsis. Finally, the severe COVID-19 infection was frequently accompanied by bacterial co-infections, as well as by the presence of significant LPS concentrations. These data indicate similarity and interdependences of both syndromes, but also significant differences which will be discussed in the present review.

The study shows that the volumes and surfaces of the $n$-simplices, $n$-orthoplices, $n$-cubes, and $n$-balls are holomorphic functions of $n$, which makes those objects omnidimensional. Furthermore, the volume of an $n$-simplex is shown to be a bivalued function of $n$, and thus the surfaces of $n$-simplices and $n$-orthoplices are also bivalued functions of $n$. Applications of these formulas to the omnidimensional polytopes inscribed in and circumscribed about $n$-balls reveal previously unknown properties of these geometric objects in negative dimensions. In particular, for $0 < n < 1$, the volumes of the omnidimensional polytopes are larger than those of circumscribing $n$-balls, while their volumes and surfaces are smaller than the volumes of inscribed $n$-balls. Reflection relations around $n = 0$ for volumes and surfaces of these polytopes inscribed in and circumscribed about $n$-balls are disclosed. Specific products and quotients of volumes and surfaces of the omnidimensional polytopes and $n$-balls are shown to be independent of the gamma function.

Diagnostics and decomposition of atmospheric disturbances in a planar flow are considered and applied to numerical modeling results with the direct possibility to use in atmosphere monitoring especially in such strong events which follow magnetic storms. The study examines a situation in which the stationary equilibrium temperature of a gas may depend on a vertical coordinate, that seriously complicates the problem solution. The relations connecting perturbations for acoustic and entropy modes are analytically established and led to the solvable diagnostic equations. These perturbation structures, found as the equation solutions specify acoustic and entropy modes in an arbitrary stratified gas under the condition of stability. These time-independent diagnostic relations link gas perturbation variables of the acoustic and the entropy modes. Hence, they provide the ability to decompose the total vector of perturbations into acoustic and non-acoustic (entropy) parts uniquely at any instant within the all accessible heights range. As a prospective model, we consider the diagnostics at the height interval [120;180] km, where the equilibrium temperature of a gas depends linearly on the vertical coordinate. For such a heights range it is possible to proceed with analytical expressions for pressure and entropy perturbations of gas variables. Individual profiles of acoustic and entropy parts for some data, obtained by numerical experiment, are illustrated by the plots for the pure numerical data against ones obtained by the model. The total energy of a flow is determined for both approaches and its height profiles are compared.

At present more than 9 million people die of cancer every year. Simple and broad-spectrum drugs are still an urgent need for cancer patients. Recently, we proposed a new hypothesis that intracellular osmotic pressure (IOP) is the driving force of cell division, and abnormal tumor proliferation is the result of uncontrolled IOP in cells. On the one hand, aneuploidy and abnormal function of Na⁺/K⁺ pump lead to a faster rise of IOP in tumor cell than normal cells, on the other hand, abnormality of cytoskeleton assembly leads to the decrease of tolerance limit of cell membrane (TLCM) of tumor cells for resisting IOP. This hypothesis predicts: 1)Tumor cells were more intolerant to hypotonic stress than normal cells. 2) Maligancies may be sellectively killed by a suddenn increase of IOP and combined with decrease of the TLCM of tumors. Na⁺/K⁺ pump inhibitors can promotely increase the IOP of tumor cells and cytoskeleton inhibitors can dramatically lower the TLCM of tumor cells. Therefore, Na⁺/K⁺ pump and cytoskeleton inhibitors may have a synergetic effect to kill tumor cells. 3) Molecules regulating cell osmolality may be new targets for cancer treatment.

NMR spectral datasets, especially in systems with limited samples, can be difficult to interpret if they contain multiple chemical components (phases, polymorphs, molecules, crystals, glasses, etc…) and the possibility of overlapping resonances. In this paper, we benchmark several blind source separation techniques for analysis of NMR spectral datasets containing negative intensity. For benchmarking purposes, we generated a large synthetic datasbase of quadrupolar solid-state NMR-like spectra that model spin-lattice T1 relaxation or nutation tip/flip angle experiments. Our benchmarking approach focused exclusively on the ability of blind source separation techniques to reproduce the spectra of the underlying pure components. In general, we find that FastICA (Fast Independent Component Analysis), SIMPLISMA (SIMPLe-to-use-Interactive Self-modeling Mixture Analysis), and NNMF (Non-Negative Matrix Factorization) are top-performing techniques. We demonstrate that dataset normalization approaches prior to blind source separation do not considerably improve outcomes. Within the range of noise levels studied, we did not find drastic changes to the ranking of techniques. The accuracy of FastICA and SIMPLISMA degrades quickly if excess (unreal) pure components are predicted. Our results indicate poor performance of SVD (Singular Value Decomposition) methods, and we propose alternative techniques for matrix initialization. The benchmarked techniques are also applied to real solid state NMR datasets. In general, the recommendations from the synthetic datasets agree with the recommendations and results from the real data analysis. The discussion provides some additional recommendations for spectroscopists applying blind source separation to NMR datasets, and for future benchmark studies. Applications of blind source separation to NMR datasets containing negative intensity may be especially useful for understanding complex and disordered systems with limited samples and mixtures of chemical components.

This study introduces a new discrete distribution which is a weighted version of Poisson-Lindley distribution. The weighted distribution is obtained using the negative binomial weight function and can be fitted to count data with over-dispersion. The p.m.f., p.g.f. and simulation procedure of the new weighted distribution, namely weighted negative binomial Poisson-Lindley (WNBPL), are provided. The maximum likelihood method for parameter estimation is also presented. The WNBPL distribution is fitted to several insurance datasets, and is compared to the Poisson and negative binomial distributions in terms of several statistical tests.

Abrasive Water Jet Machining (AWJM) is a non-conventional machining process that, unlike other methods, is deemed superior because of its applicability, versatility, and no heat-affected zones in the target material. The main objective of this paper was to develop a cheap, practical model for a low-pressure water jet cutting machine and provide some empirical test data for cutting delicate materials. Proper design calculations were performed and are included for both the water jet machine and the two-axis numerical control. Finite Element Analysis results validate the structural integrity of beams and columns in AWJM. Computational Fluid Dynamic analysis of the nozzle shows good agreement with the theoretical calculations regarding the pressure and velocity of the water-abrasive mixture exiting the nozzle. Modal analysis in ANSYS was done to mitigate potential failure due to resonance induced by vibrations. Limited testing on various thicknesses of polystyrene foam ranging from 1-5 mm thickness and rubber sheet of 1 mm thickness showed that even low pressure of 25-30 bar was sufficient to produce a kerf without any burr. However, extensive testing to report optimized parameters like nozzle transverse speed, standoff distance, abrasive flow rate, etc for working at low-pressure ranges is still a consideration for future investigation.

The structural, elastic, and electronic properties of orthorhombic Cd2SiO4 and Hg2GeO4 were examined under varying pressure conditions using first-principles calculations based on densi-ty-functional theory employing the projector augmented wave method. The obtained cell pa-rameters at 0 GPa were found to align well with existing experimental data. We delved into the pressure-dependence of normalized lattice parameters and elastic constants. In Cd2SiO4, all lat-tice constants decreased as pressure increased, whereas in Hg2GeO4, parameters a and b de-creased while parameter c increased under pressure. Employing the Hill average method, we calculated the elastic moduli and Poisson’s ratio up to 10 GPa, noting an increase with pressure. Evaluation of ductility/brittleness under pressure indicated both compounds remained ductile throughout. We also estimated elastic anisotropy and Debye temperature under varying pres-sures. Cd2SiO4 and Hg2GeO4 were identified as indirect band gap insulators, with estimated band gaps of 3.34 eV and 2.09 eV, respectively. Interestingly, Cd2SiO4 exhibited a significant increase in band gap with increasing pressure, whereas the band gap of Hg2GeO4 decreased under pres-sure, revealing distinct structural and electronic responses despite their similar structures.

Abstract:High-pressure water jet technology has received extensive attention and application due to its high efficiency and environmental protection characteristics. The high-pressure water jet nozzle is its core component, and the research on the high-pressure water jet nozzle is conducive to improving the jet performance and improving the jet efficiency. This paper introduces the characteristics of water jet and the working principle of pure water jet, abrasive water jet, pulsed water jet and cavitation water jet, reviews the theoretical analysis and experiment of the predecessor's nozzle, briefly explains the application of high-pressure water jet and looks forward to the development trend of this technology.

This study investigates the suitability of the timestamp approach algorithm for predicting blood pressure (BP) using wearable and comfortable devices, showcasing its accuracy even with low-frequency sampled signals. Developed within the SINTEC European project, the algorithm utilizes Electrocardiogram (ECG) and Photoplethysmogram (PPG) sensors, demonstrating promising results in both laboratory and hospital settings. The research emphasizes the algorithm’s potential to transform continuous and non-invasive BP monitoring through wearable technology, offering frequent measurements with minimal discomfort. While the study shows promise, further exploration is needed, focusing on optimizing machine learning coefficients for long-term monitoring applications and addressing potential changes over time. Technological improvements, including the implementation of edge computing algorithms, hold the key to enhancing BP accuracy, denoising techniques, and integrating alarm systems for future wearable solutions. This study emphasizes the adaptability of the algorithm for diverse healthcare environments, paving the way for broader applications in convenient and reliable BP monitoring.

The surrounding rock during the coal mine excavation is prone to significant engineering disasters such as considerable deformation and rockbursts. Pressure release can improve the stress field of a deep rock mass and prevent the occurrence of dangers such as roadway collapse and coal and gas outbursts. This paper uses the ANSYS/LS-DYNA finite element software to simulate the crush area and fracture zone of a detonation charge with different diameters under in-situ stress. The stability of the surrounding rock was analyzed based on the impact stress and velocity, and was verified by field tests. The research results show that the blasting load primarily affects the damaged area near the borehole, while the in-situ stress affects the far-field crack propagation. The crack propagates in the direction of high surrounding rock pressure. When the uncoupling index is 1.5, the impact pressure of the 60 mm diameter cartridge is 8 times that of the 20 mm diameter cartridge. The impact speed can reach 2 times that of the 20 mm diameter cartridge. The high-energy event of the roof is transferred to the front of the working face, the distribution is no longer concentrated, and a better blasting pressure relief effect is achieved. The research results can help guide the prevention and control measures of rock bursts and other mining disasters.

Demolished concrete and plastic waste are two increasingly aggravating problems. In this study, a novel method was proposed to simultaneously recycle concrete and plastic wastes by compacting concrete and plastic powders together under pressure and temperature. The influence of compression pressure and temperature as well as the mixture proportion on the bending strength of specimens was investigated. The results showed that pressure and temperature had a positive effect on the specimen strength; however, the molding temperature should not exceed the melting temperature of plastic. The proportion of plastic had a minimal effect on the bending strength of the specimen when plastic accounted for 25%–75% of the overall mass of the test piece.

In reservoir engineering, one of the main sources of information for the characterization of reservoir and well parameters is well testing. Among the unconventional well testing methodologies, Harmonic Well Testing (HPT) is appealing from an economic standpoint because it could provide well performance and reservoir behavior monitoring without having to interrupt field production. Recorded pressure analysis is performed in the frequency domain by adopting a derivative approach similar to conventional well testing. To this end, pressure and rate data must be decomposed into harmonic components. Test interpretability can be significantly improved if pressure data are detrended prior to interpretation, filtering out non periodic events such as discontinuous production from neighboring wells and flow regime variations which did not respect the designed test periodicity. Therefore, detrending offers the possibility of overcoming the limitation of HPT applicability due to the difficulty of imposing a regularly pulsing rate for the whole test duration (typically lasting several days). This makes HPT attractive for well performance monitoring, especially in gas storage fields. In this paper, the application of different detrending methodologies to synthetic HPT pressure data generated in different reservoir and operational scenarios is presented and discussed. Moreover, a real case application is also presented.

Most of the research in data mining concentrated on finding the positive associations that exist in frequent patterns. Frequent patterns have no bearing on the time duration and, therefore, lose interestingness. The Regularity of an itemset is related to the time at which the transaction occurred and the time distance between the transactions. Frequent Regular item sets can be generated considering the Frequency and the Regularity of the occurrence of the Item Sets. The frequent and regular Item sets will be so huge that they cannot be handled in real time. The count of Frequent and regular item sets gets reduced drastically when the properties “closed” and “Maximality” are applied. Finding negative associations among such patterns are important in the field of medicine. Many drugs administered to cure some diseases have counter reactions leading to many other diseases. Negative associations among the mined patterns are important as they reveal significant contradictions frequently among medical drugs administered by medical practitioners to cure some diseases. This paper proposes a method that mines medical databases to find regular, frequent patterns applied with closed and maximal properties and find negative associations among those patterns. The proposed algorithm is accurate to 98% and performs 9% more efficiently than the other algorithms presented in the literature.

Bacteremia and fungemia are significant causes of morbidity and mortality which frequently occur as co-infections with viral respiratory infections including SARS-CoV-2. It was aimed to evaluate the microorganisms isolated from blood cultures of SARS-CoV-2 positive and negative patients and investigate their antimicrobial resistance patterns. A retrospective analysis was performed with the total number of 22,944 blood cultures sent to the laboratory between November 2020 and December 2021. Blood cultures were performed on the BD Bactec automated system. Identification was performed using conventional methods, VITEK-2 and MALDI-TOF MS. Antibacterial/antifungal susceptibility tests were performed according to EUCAST/CLSI recommendations. SARS-CoV-2 tests were performed with RT-PCR. It was detected 1,630 culture positivity belonging to 652 patients. Totally 633 of 652 patients were tested for SARS-CoV-2; 118 (18.6%) were positive and 515 (81.3%) were negative. The bacteria and fungi isolated at the high-est rate in SARS-CoV-2 positive patients were methicillin-resistant coagulase negative staphylococci (MR-CoNS) (21.5%), Escherichia coli (12.4%), Klebsiella pneumoniae (12.4%), Candida albicans (1.65%) and Candida glabrata complex (1.65%); while in negative patients, E. coli (21.3%), MR-CoNS (13.5%), K. pneumoniae (12.05%), C. albicans (2.1%), Candida parapsilosis (1.1%) and Candida tropicalis (0.9%). The fact that the most common isolate was MR-CoNS in SARS-CoV-2 positive patients (p = 0.028); the detection of Acinetobacter baumannii was more frequent (p = 0.001) and the isolation of carbapenem-resistant K. pneumoniae was at a higher rate than in SARS-CoV-2 negative patients; also, the increase in multidrug-resistant strains indicate that healthcare-associated infec-tions should not be disregarded while focusing on the outbreak.

Diffusion-controlled cyclic voltammograms at fast scan rates show peak shifts as well as decreases in the peak currents from the predicted diffusion-controlled currents especially when currents are large in low concentration of supporting electrolyte. This has been conventionally recognized as an IR-drop effect by solution resistance on the peaks as well as heterogeneous kinetics. It is also brought about by negatively capacitive currents associated with charge transfer reactions. The reaction product generates dipoles with counterions to yield a capacitance, of which current flows oppositely to that of the double layer capacitance. The three effects are specified here in the oxidation of a ferrocenyl derivative by fast scan voltammetry. The expression for voltammograms complicated with IR-drop is derived analytically, and yields deformed voltammograms. The peak shift is approximately linear with the IR-term, but exhibits a convex variation. Dependence of some parameters on the peaks by the IR-drop is compared with those by the negative capacitance. The latter is more conspicuous than the former under conventional conditions. The two effects cannot be distinguished specifically except for variations of conductance of the solution.

Crop disease classification has always been a critical and persistent problem in the field of agricultural and forestry sciences, where often we do not have access to a sufficient number of samples to know the distribution of real-world samples. How to make full use of the existing data is the starting point of our thinking. To address this problem, this paper proposes a supervised image augmentation method Negative Contrast, which uses the contrast images of existing disease samples after removing disease areas as negative samples for image augmentation when samples are relatively scarce. Numerous experiments have shown that several classical models using this augmentation method have improved in disease classification of four crops, rice, wheat, corn, and soybean, with a maximum accuracy improvement of 30.8%. In addition, the comparative analysis of attentional heat map shows that the model using Negative Contrast is more accurate and intense on the area of interest of diseases, and thus reflects better generalization ability in real-world disease classification. Our dataset and codes can be found in https://www.kaggle.com/datasets/w970704112/corn-wheat-rice-soybean and https://github.com/hiter0/contrastaug .

Women have been leading organizations and communities for centuries, but their journeys in leadership have sometimes been challenging. This paper aims to reflect on women's positive and negative experiences in leadership roles and understand the factors contributing to their successes and challenges.To explore these issues, we will draw on various academic literature, including studies on gender and leadership and case studies of women in leadership positions. We will also examine the cultural and social factors that affect women's experiences in leadership, including bias and discrimination, societal expectations, and work-life balance challenges.One key theme from this analysis is the importance of role models and support networks in helping women succeed in leadership roles. Women with access to mentorship, sponsorship, and peer networks are more likely to thrive in their roles and overcome the challenges they may face. However, lacking female role models and mentors can make it difficult for women to advance in their careers and contribute to feelings of isolation and imposter syndrome.Another important theme is the need for organizations and society to address systemic biases and discrimination that prevent women from reaching their full potential. This can include initiatives such as unconscious bias training, flexible work arrangements, and policies that support gender diversity and inclusion.In conclusion, this paper highlights women's positive and negative experiences in leadership roles and emphasizes the need for ongoing efforts to support and empower women in leadership. By addressing the challenges women face and building a culture of inclusion and support, organizations and society can help unlock the full potential of women leaders and create a more equitable and just world.

Among the biggest challenges facing the contemporary human condition, and therefore also education, is responding to the climate crisis. The source of the crisis is assumed to be absent-mindedness, presented by Leslie Dewart as a distortion of the development of human consciousness. Dewart's poorly-known philosophical consciousness study is presented in this paper in broad outline. The problems in the study of consciousness, the most important of which are the qualitative representations – qualia – and the question of free will, are also briefly discussed. These problems are then examined transcendental analytically, with the question of what one must assume in order to allow the emergence of these phenomena. From the resulting conception of causal relationship, we proceed to the circular causality as a prerequisite for life, namely the homeostatic systems and negative feedback. An organization of action that is essential to animals and humans is presented, using William Powers’ perceptual control theory (PCT), and the role of consciousness in this organization is drafted according to the studies of Martin Taylor. Action is seen as continuous problem solving, in which negative feedback is used to bring perceptions into line with the goals. The fundamental function of consciousness is revealed as the direction and enhancement of learning. Based on PCT, it can be shown that the main practical problems in animal and, especially, human action, are related to adverse side effects of action and the resulting various conflicts. The climate crisis is a typical example of the problematic side effects of collective action. Dewart's concept of absent-mindedness can therefore be defined as an inability to responsibly account for the side effects of action. Thus, the main task of education is to forestall, through negative feedback and in cooperation with learner consciousness, absent-mindedness and the problems it causes.

Negative corona discharges occur widely in high voltage transmission lines and charged aircraft, which can cause strong electromagnetic interference. Negative corona discharge is typically performed simultaneously at multiple discharge points. In this study, the current and its EM radiation characteristics of single-needle and multi-needle negative corona discharge in different conditions were tested. The current and electromagnetic radiation characteristics of the two discharge structures were compared. The dipole radiation model was established to analyze the EM radiation characteristics of the negative corona discharge.The results show that, It is only when the voltage reaches a certain threshold that the current and electromagnetic radiation fields of the multi-needle discharge structure will be superimposed and their amplitudes will increase significantly. The frequency of electromagnetic radiation signal does not change with the number of needles, cathode geometry and applied voltage, but only depends on ambient pressure. It provides a basis for detecting corona discharge sources under different conditions.

Purpose: The deterioration of oral function has been getting much attention as “Oral frailty”. This study evaluated the change in tongue pressure, one of the objective items of oral frailty, to examine the relationship between body position and tongue pressure. Methods: This study was prospective, observational study in a single-center. The participants were categorized by Clinical Frailty Scale (CFS). Tongue pressure was measured in the following positions: dorsal, sitting, and sitting with plantar grounding. Differences in tongue pressure between CFS and between body positions were statistically analyzed. Results: A significant decrease in tongue pressure was demonstrated in CFS4 compared to CFS3. Furthermore, in CFS5 and CFS6, tongue pressure decreased in the sitting po-sition compared to that in the dorsal position and recovered to the dorsal level with plantar grounding. Conclusions: Tongue pressure decreased as the progression of frailty. It decreased by sitting, and this decrease was alleviated by plantar grounding.

To explore the impact of parenting styles on the perception of campus non-physical bullying, 492 students in upper elementary school grades were surveyed by using the Delaware Bullying Victimization Scale, the Negative Coping Style Scale, the Negative Affect Scale, and the Egna Minnen Beträffende Uppfostran Questionnaire. The questionnaire survey was conducted in the fifth and sixth grades of eight primary schools in Zhejiang province. The results showed that cyberbullying was not significantly related to an anxious parenting style, but negative affect experiences, negative coping styles, negative family parenting styles, and the perception of campus non-physical bullying were all positively correlated with each other (p < 0.05). The refusal parenting style was shown to be an important factor that affected students’ perception of campus non-physical bullying; it was observed to directly affect students’ perception of campus non-physical bullying and indirectly affect students’ perception of campus non-physical bullying by influencing negative affect experiences and negative coping styles. In conclusion, negative affect experiences and negative coping styles had a chain-like mediating effect between the refusal parenting style and students’ perception of campus verbal bullying. Moreover, negative affect experiences had a partial mediating effect between the refusal parenting style and students’ perceptions of campus cyberbullying, relationship bullying, and non-physical bullying total scores. Implications and suggestions based on these results are also discussed.

The precipitation, flocculation, and deposition of asphaltene cause severe formation damage within a reservoir and shorten a well’s productive life. Pressure depletion is one factor that contributes to asphaltene precipitation during production; therefore, the first step in managing asphaltene is to determine the onset pressure of the precipitation. While there are numerous equation of state models that can be used to predict the onset pressure, these models are complex and heavily reliant on tuning parameters. Using multivariate linear regression, this work attempts to develop a simple and accurate thermodynamic model for predicting the upper precipitation onset pressure under pressure depletion above the bubble point pressure (Pb) at various temperatures. A total of 94 experimental data points from 37 published crude oil data sets were compiled from the literature. To develop the model, 59 experimental data points were used as training data and 35 experimental data points as testing data. According to the results of the multicollinearity test, the bubble point pressure, temperature, resins, and saturate-to-aromatic ratio were chosen as predictors. The upper onset pressure data with comparable trends were clustered, and unsupervised recognition of three distinct cluster groups was performed. For each cluster identified, a multivariate linear regression model was developed. The model was chosen based on Mallow’s coefficient of determination (Cp), adjusted R² (statistical measure of fit), and S (standard error of the regression slope). The developed model was tested using a data set, and the results showed an adjusted R² of 96.25%, with a mean absolute error of 4.1%. The model was randomly applied to 15 data points to compare it to perturbed-chain statistical associated fluid theory (PC SAFT) and the Peng-Robinson equation of state models and to the multivariate regression models of Fahim (2007) and Ameli et al. (2016). The results showed that the mean absolute error for predicting the asphaltene precipitation onset pressure was 2.82% using Peng-Robinson, 2.36% using the PC SAFT equation of state, 23.96% using the Fahim model, 24.80% using the model reported by Ameli et al., and 2.39% using the newly developed multivariate regression model. The developed multivariate model appears to be as accurate as the PC SAFT equation of state modeling with tuning parameters. The primary advantage of multivariate regression is that, unlike the PC SAFT equation of state model, it does not require saturates, aromatics, resins, and asphaltenes (SARA)-based characterization methodologies or rigorous parameter tuning. It is simple to use, quick, and it produces results in a short period of time.

Simple Summary: Breast cancer is the most common invasive cancer among women. Triple-negative breast cancer (TNBC) accounts for 15–20% of newly diagnosed breast cancers and has the worst prognosis. However, TNBC patients are not a homogeneous group, and there are differences in the course of the disease as well as in response to treatment. For this reason, differentiation of subtypes of this tumor is important for optimal therapeutic decision and risk prediction. The presented study focuses on the expression of the androgen receptor (AR) and the infiltration of T-lymphocytes in the tumor stroma (TILs) of TNBC patients. Correlation of these tested biomarkers with standard prognostic factors. Defining new prognostic factors for 3-year overall survival (OS). Abstract: Background: Analysis of the practical benefit of testing the expression of AR and the TILs in patients with TNBC and their correlation with standard prognostic factors. Methods: The study group consisted of 86 female patients treated for TNBC. T-lymphocyte infiltration was examined in H+E staining. AR expression, CD8 and CD4 T-lymphocytes were evaluated in immunohistochemistry. Results: Significantly negative correlation was found between AR expression and the CD8 T-lymphocyte infiltration levels. A significant negative correlation was found between the AR expression and G and Ki 67, and a positive correlation between the TILs levels and G and Ki 67. Patients with AR expression and low TILs levels had the highest percentage of diagnosed distant metastases and 3-years OS. Patients with high TILs no distant metastases or deaths were diagnosed. The level of TILs turned out to be a significant independent prognostic factor. Conclusions: Based on the assessment of AR expression and TILs infiltration, the group of highest and lowest risk was determined. The prognostic factor of known parameters such as TNM and a new factor - TILs was confirmed. On the other hand, parameters such as G and Ki 67 and the tested factor - AR had no effect on the prognosis.

Chronic exposure to the nephrotoxic metal pollutant, cadmium (Cd), has been associated with the pathogenesis of hypertension, but so far, the mechanism has not been well defined. We hypothesize that exposure to Cd causes a decline in the glomerular filtration rate (GFR), which in turn, causes a rise in blood pressure. Data were collected from 447 Thai subjects with a mean age of 51.1 years, of which 48.8% had hypertension, 15.4% had diabetes and 6.9% had an estimated GFR (eGFR) below 60 mL/min/1.73m2 (low eGFR). The mean blood Cd and mean urinary Cd concentrations were 2.75 and 4.23 µg/L, respectively. Prevalence odds ratio (POR) for hypertension rose twofold in those with a medium Cd burden and blood Cd levels of 0.61-1.69 µg/L. In the hypertensive group, the eGFR was inversely associated with age (β =−0.517), the Cd excretion rate (β = −0.177), and diabetes (β = −0.175). Mean eGFR in those with hypertension was 7.5 mL/min/1.73m2 lower than those who were normotensive with the same Cd body burden. In addition, higher systolic blood pressure (SBP) values were associated with older age (β = 0.243), higher BMI (β = 0.113), lower eGFR (β = −0.106) and diabetes (β = 0.216). Mean SBP in those who had low eGFR and medium and heavy Cd body burden was 9.5 mmHg higher than those with the same Cd body burden and a normal eGFR. Thus, chronic environmental exposure to Cd that produces urinary and blood Cd levels of 0.57-0.61 µg/L, increases the risk of hypertension, and this could be mediated by a declining GFR.

This study examined the association between pressure injuries and complexity of abdominal temperature measured in residents of a nursing facility. The temperature served as a proxy measure for skin thermoregulation. Refined multiscale sample entropy and bubble entropy were used to measure the complexity of the temperature time series measured over two days at 1-minute intervals. Robust summary measures were derived for the multiscale entropies and used in predictive models for pressure injuries that were built with adaptive lasso regression and neural networks. Both types of entropies were lower in the group of participants with pressure injuries (n=11) relative to the group of non-injured participants (n=15). This was generally true at the longer temporal scales, with the effect peaking at scale τ=23 minutes. Predictive models for pressure injury on the basis of refined multiscale sample entropy and bubble entropy yielded 92% accuracy, outperforming predictions based on any single measure of entropy. Combining entropy measures with a widely used risk assessment score led to the best prediction accuracy. Complexity of abdominal temperature series could therefore serve as an indicator of risk of pressure injury.

Background: Morphological alterations in intracranial pressure pulse waveform (ICPPW) secondary to intracranial hypertension (ICP >20 mmHg) and reduction in intracranial compliance (ICC) are well known indicators of neurological severity. To date, no studies have documented the ICPPW modifications after intracranial hypertension resolution with decompressive craniectomy (DC). The present study aimed to assess the morphological alterations in ICPPW among neurocritical care patients with and without DC, by comparing the variations of ICPPW features according to elevations in mean ICP values. Methods: Patients requiring ICP monitoring because of severe traumatic or spontaneous conditions were included. Mean ICP values were compared with ICPPW features (P2/P1 ratio, TTP and pulse amplitude). Elevation in ICP was produced by means of ultrasound-guided manual internal jugular veins compression. Results were distributed for three groups: intact skull (exclusive burr hole for ICP monitoring), craniotomy/large fractures (group 2) or DC (group 3). Results: 57 patients were analyzed. 21 (36%) presented no skull defects, whereas 15 (26%) had DC. ICP was not significantly different between groups: ±13.59 for intact and ±17.66 mmHg for DC, with ICP induced elevation also similar between groups (p= 0.56). Significant elevation was observed for P2/P1 ratio for groups 1 and 2, whereas reduction was observed in group 3 (elevation of ±0.09 for groups 1 and 2, whereas reduction of 0.03 for group 3, p=0.01). Conclusion: In the present study, intracranial pressure pulse waveform analysis indicated that intracranial compliance was significantly more impaired among decompressive craniectomy patients, although ICPPW indicated DC to be protective for further influences of ICP elevations over the brain. Analysis of ICPPW seems to be an alternative to real time ICC assessment.

Negative thermal quenching (NTQ) denotes that the integral emission spectral intensity of a given phosphor increases continuously with increasing temperature up to a certain elevated temperature. NTQ has been a subject of intensive investigation in recent years and a large number of phosphors were reportedly to have exhibited NTQ. In this paper, a collection of results in the archival literature about NTQ of specific phosphors are discussed from a macroscopic viewpoint in the following three aspects:1) Could NTQ of a given phosphor be reproducible?2) Could the associated data for a given phosphor exhibited NTQ be in line with the law of conservation of energy?3) Could NTQ of a given phosphor be demonstrated in a prototype WLED device? By analyzing typical cases based on common sense, it is hoped to increase the awareness for the issues with the papers reporting NTQ of the specific phosphors based on spectral intensity along with for the importance of keeping stability and consistency of the measurement conditions in temperature-dependent spectral intensity measurement which is a prerequisite for the validity of the measurement results.

Standard of care for triple negative breast cancer (TNBC) involves the use of microtubule poisons like paclitaxel, which are proposed to work by inducing lethal levels of aneuploidy in tumor cells. While these drugs are initially effective in treating cancer, dose-limiting peripheral neuropathies are common. Unfortunately, patients often relapse with drug resistant tumors. Identifying agents against targets that limit aneuploidy may be a valuable approach for therapeutic development. One potential target is the microtubule depolymerizing kinesin, MCAK, which limits aneuploidy by regulating microtubule dynamics during mitosis. Using publicly available datasets, we found that MCAK is upregulated in triple negative breast cancer and is associated with poorer prognoses. Knockdown of MCAK in tumor-derived cell lines caused a two- to five-fold reduction in the IC50 for paclitaxel, without affecting normal cells. Using FRET and image-based assays, we screened compounds from the ChemBridge 50k library and discovered three putative MCAK inhibitors. These compounds reproduced the aneuploidy-inducing phenotype of MCAK loss, reduced clonogenic survival of TNBC cells regardless of taxane-resistance, and the most potent of the three, C4, sensitized TNBC cells to paclitaxel. Collectively, our work shows promise that MCAK may serve as both a biomarker of prognosis and as a therapeutic target.

46 patients with a newly diagnosed, histologically verified glioma that was visually classified as [18F]FET-negative were included. Tumor volumes were defined using routine T2/FLAIR MRI data and applied to extract information from dynamic [18F]FET PET data, i.e. early and late tu-mor-to-background (TBR5-15, TBR20-40) images and time-to-peak (TTP) images. Radiomic features of healthy background were calculated from the tumor volume-of-interest mirrored to the con-tralateral hemisphere. Differences between tumor and healthy tissue features were compared us-ing Wilcoxon test. Additionally, the ability to distinguish tumor from healthy tissue was assessed using logistic regression. 5 % of features derived from TBR20-40 images were significantly differ-ent; 16 % of features derived from TBR5-15 images and 69 % of features derived from TTP images. The high number of significantly different features derived from TTP images was even found in isometabolic gliomas (after exclusion of photopenic gliomas) with visually normal [18F]FET up-take in static images. However, the differences did not reach satisfactory predictability for ma-chine learning based identification of tumor tissue. In conclusion, radiomic features derived from dynamic [18F]FET PET data may extract additional information even in [18F]FET-negative glio-mas, which should be investigated in larger cohorts and correlated with histological and out-come features in future studies.

This review reports the available technologies for the flexible utilization of biomass towards negative CO₂ emissions and addresses the possibility to couple biogas production plants with the electrical grid converting excess electrical energy into storable chemical molecules. This changed mind-set towards biomass utilization can lead readily to the implementation of negative CO₂ emission along the entire bioenergy supply chain without limiting the potential for Power-to-X applications. First, the technologies for direct conversion of waste and wood into gaseous energy carriers are screened, to highlight the potential for the production of renewable fuels. Second, the processes for the removal of CO₂ from biogenic gas streams are analysed in terms of technological performance, cost and further potential for the CO₂ recovered. These technologies are the key to pre-combustion CO₂ capture and negative emissions. Third, the possibility of coupling biomass conversion and synthetic fuels production is explored, providing an overview on the technical maturity of the various energy storage processes. The flexible use of biomass can be an essential part of the future CO₂-free energy systems, as it can directly provide energy carriers all around the year and also large quantities of climate-neutral carbon for the production of synthetic fuels with renewable energy. In turn, when no additional renewable electricity is available, the CO₂ by-product from biofuel synthesis can be used for the negative emissions. This opens the way to an efficient strategy for the seasonal storage of electrical energy, realizing a carbon-neutral energy system coupled with the development of carbon-negative energy strategy.

Here, we report a simple and effective method for separation of gram-negative bacteria using aptamer-modified microbeads and acoustophoresis. As acoustophoresis allows for simultaneous washing and size-dependent separation in continuous flow mode, we efficiently obtained gram-negative bacteria that showed high affinity without any additional washing steps. The proposed device has a simple and efficient channel design, utilizing a long, square-shaped microchannel that shows excellent separation performance in terms of the purity, recovery, and concentration factor. Microbeads (10 µm) coated with the GN6 aptamer can specifically bind gram-negative bacteria. Using acoustophoresis, gram-negative bacteria-bound microbeads and other unbound/contaminants can be separated by size with high purity and recovery. The device demonstrated excellent separation performance, with high recovery (up to 98%), high purity (up to 99%), and a high volume rate (500 µL/min), and a concentration factor of up to 20×. The acoustophoresis microfluidic device also showed binding affinity to multiple strains of gram-negative bacteria, but not to gram-positive bacteria. This study presents a new paradigm for early diagnosis of bacterial infectious diseases. In addition to detecting living bacteria or bacteria-derived biomarkers, this protocol can be extended to monitoring the contamination of water resources, and may aid quick responses to bioterrorism and pathogenic bacterial infections.

We study impact of geometry on leakage loss in negative curvature fibers made with As₂Se₃ chalcogenide and As₂Se₃ chalcogenide glasses for carbon dioxide (CO₂) laser transmission. The minimum leakage loss decreases when the core diameter increases both for fibers with six and for fibers with eight cladding tubes. The optimum gap corresponding to the minimum loss increases when the core diameter increases for negative curvature fibers with six cladding tubes. For negative curvature fibers with eight cladding tubes, the optimum gap is always less than 20 μm when the core diameter ranges from 300 μm to 500 μm. The influence of material loss on fiber loss is also studied. When material loss exceeds 10² dB/m, it dominates the fiber leakage loss for negative curvature fiber at a wavelength of 10.6 μm.

A physical model based on the mechanism observed in experimental investigations is introduced to describe the formation of negative leader steps. Starting with a small length of a space leader located at the periphery of the negative streamer system of the stepped leader the model simulates the growth and the subsequent formation of the leader step. Based on the model, the average step length, the average step forming time and the average stepped leader propagation speed is estimated as a function of prospective return stroke peak current. The results show that the average step length and the average leader speed increases with increasing prospective return stroke current. The results also show that the speed of the stepped leader increases as it approaches the ground. For a 30 kA prospective return stroke current the average leader speed obtained is about 5 x 10⁵ m/s and the average step length was about 10 m. The results obtained are in reasonable agreement with the experimental observations.

In this paper, a regression model between neutron star crust-core pressure and the symmetry energy characteristics was estimated using the Akaike information criterion and the adjusted coefficient of determination Radj2. Based on the obtained regression function, the most probable value of the transition density, which should characterize the crust-core environment of the sought physical neutron star model, was determined. An anti-correlation was found between this transition density and the main characteristic of the symmetry energy, i.e., its slope L.

Ankle joint flexion and extension exercises play an important role in the rehabilitation training of patients who have been injured or bedridden for a long time before and after surgery. Accurately guiding patients to perform ankle flexion and extension exercises can significantly reduce deep vein thromboembolism. Currently, most ankle rehabilitation devices focus on assisting patients with ankle flexion and extension movements, and there is a lack of devices for effectively monitoring these movements. In this study, we designed an ankle joint flexion and extension movement monitoring device based on a pressure sensor. It is composed of an STM32 microcontroller, a pressure sensor, an HX711A/D conversion chip, and an ESP8266 WiFi communication module. The value of force and effective number of ankle joint flexion and extension movements were obtained. An experimental device was designed to verify the accuracy of the system. The results showed that the device can effectively monitor and control ankle flexion and extension movements remotely, ultimately ensuring that the patient can effectively monitor and grasp the active ankle pump movement.