The main purpose of this study was to create a prototype of an unmanned aerial system equipped with intelligent hardware and software technologies necessary for monitoring the health and growth of crops in orchards. Another important objective was to use low-cost sensors that accurately measure ultraviolet solar radiation. The device, which needs to be attached to the commercial DJI Mini 4 Pro drone, should be small in size, portable, and have very low energy consumption. For this purpose, the widely used Vishay VEML6075 digital optical sensor was selected and implemented in a prototype, alongside a Raspberry Pi Zero 2W minicomputer. To collect data from these sensors, a program written in Python was used, containing specific blocks for data acquisition from each sensor, to facilitate the monitoring of ultraviolet (UV) radiation, or battery current. By analyzing the data obtained from the sensors, several important conclusions are drawn that may provide valuable pathways for the further development of mobile or modular equipment. Furthermore, the results of the plant condition analysis with proposed models in the Geographic Information System (GIS) environment were also presented. The visualization of maps indicating variations in vegetation condition led to the identification of problem areas like hydric stress.

The Energy Performance of Buildings Directive 2010 calls for the Nearly Zero Energy Standard for new buildings from 2021 onwards: Buildings using “almost no energy” are powered by renewable sources or energy produced by the building itself. For residential buildings, this ambitious new standard has already been reached. But for other building types this goal is still far away. The potential of these buildings to meet a Nearly Zero Energy Standard was investigated by analyzing ten case studies representing non-residential buildings with different uses. The analysis shows that the primary characteristics common to critical building types are a dense building context with a very high degree of technical installation (such as hospital, research and laboratory buildings). The large primary energy demand of these types of buildings cannot be compensated by building and property-related energy generation including off-site renewables. If the future Nearly Zero Energy Standard were to be defined with lower requirements because of this, the state related properties of Bavaria suggest that the real potential energy savings available in at least 85% of all new buildings would be insufficiently exploited. Therefore, it would be useful to instead individualize the legal energy verification process for new buildings to distinguish critical building types such as laboratories and hospitals.

Geminiviruses possess single-stranded, circular DNA genomes, and control the transcription of their late genes, including BV1 of many bipartite begomoviruses, through transcriptional activation by the early expressing AC2 protein. DNA binding by AC2 is not sequence-specific, hence the specificity of AC2 activation is thought to be conferred by plant transcription factors (TFs) recruited by AC2 in infected cells. However, the exact TFs AC2 recruits are not known for most viruses. Here we report a systematic examination of the BV1 promoter (PBV1) of mungbean yellow mosaic virus (MYMV) for conserved promoter motifs. We found that MYMV PBV1 contains three abscisic acid (ABA)-responsive elements (ABREs) within its first 70 nucleotides. Deleting these ABREs, or mutating them all via site-directed mutagenesis, abolished the capacity of PBV1 to respond to AC2-mediated transcriptional activation. Furthermore, ABRE and other related ABA-responsive elements were prevalent in more than a dozen Old World begomoviruses we inspected. Together these findings suggest that ABA-responsive TFs may be recruited by AC2 to BV1 promoters of these viruses to confer specificity to AC2 activation. These observations are expected to guide the search for the actual TF(s), furthering our understanding of the mechanism of AC2 action.

This study highlighted the core and critical tenets that constitute culturally responsive science assessments (CRSciA) for K-12 education and aligned them with the capabilities of generative AI (GenAI). The tenets were identified based on their dominance in the literature, including Indigenous Language, Race and Ethnicity, Religious Beliefs, Family and Community, and Indigenous Knowledge. These tenets were instrumental in developing the GenAI-CRSciA framework and the subsequent prompts to generate CRSciAs aligned with the Next Generation Science Standards (NGSS) while comparing it with standard prompt strategies. The results showed that the GenAI-CRSciA prompting approach outperformed normal prompting strategies in terms of generating CRSciAs, proving its effectiveness in addressing the ongoing challenges in science assessments. Even though the GenAI-CRSciA framework presented assessments that cover a range of the cultural backgrounds, it presents potential challenges such as compromising curricula core competencies and overgeneralization of students’ backgrounds; overlooking subcultural variations within a country or region, for example differences between urban and rural students, or between different ethnic or linguistic groups within the same nation, which can lead to bias and less effective CRSciA outputs. To address this, we recommend that teachers provide comprehensive and specific background information about their students when using the GenAI-CRSciA prompting, ensuring that the generated content is truly reflective of the students’ unique cultural contexts. In larger class settings, teachers could implement comprehensive local data indexing, where detailed student background information is uploaded and retrievable for use in crafting more personalized CRSciAs. We strongly recommend educators to make conscious efforts to validate the generated assessments with input from human experts, including community or family, educators, and even students who are knowledgeable about the cultural nuances. We also suggest continuous professional development would be necessary to enhance teachers’ understanding of the cultural tenets.

Nitrates can cause severe ecological imbalances in aquatic ecosystems, with considerable consequences for human health. Therefore, monitoring this inorganic form of nitrogen becomes essential for any water quality management structure. This research aimed at developing a novel Nitrate Portable Measurement System (NPMS) for monitoring nitrate concentrations in water samples. NPMS is a reagent-free ultraviolet system developed using low-cost electronic components. Its operation principle is based on Beer-Lambert law for measuring Nitrate concentrations in water samples through light absorption in the spectral range 295-315 nm. The system is equipped with ready to use ultraviolet sensor, Light Emission Diode (LED), op-amp, microcontroller, liquid crystal display, quartz cuvette, temperature sensor, and battery. All the components are assembled in a 3D-printed enclosure box which allows a very compact self-contained equipment, with high portability, enabling field and near real time measurements. The proposed methodology and the developed instrument were used to analyse multiple nitrate standard solutions. The performance was evaluated in comparison with the Nicolet Evolution 300, a classical UV-Vis spectrophotometer. The results demonstrate a strong correlation between the retrieved measurements by both instruments within the investigated spectral band and for concentrations above 5 mg NO3- /l.

Polypyrrole (PPy)-capped caped silver nanowire (Ag NW) nanomaterials (core–shell rod-shaped Ag NW@PPy) were synthesized suing a one–port suspension polymerization technique. The thickness of PPy layer on the 50-nm-thickness/15-μm-length Ag NW was effectively controlled to 10, 40, 50, and 60 nm. Thin films cast from one-dimensional conductive Ag NW@PPy formed a three-dimensional (3-D) conductive porous network structure and provided excellent electrochemical performance. The 3-D Ag NW@PPy network can significantly reduce the internal resistance of the electrode and maintain structural stability. As a result, a high specific capacitance of 625 F/g at a scan rate of 1 mV/s was obtained from the 3-D porous Ag NW@PPy composite film. The cycling performance over a long period exceeding 10,000 cycles was also evaluated. We expect that our core–shell-structured Ag NW@PPy composites and their 3-D porous structure network films can be applied as electrochemical materials for the design and manufacture of supercapacitors and other energy storage devices.

Phenylketonuria is an inherited metabolic disorder that leads to neurobehavioral dysfunction. The main treatment is a low-phenylalanine diet and/or the cofactor tetrahydrobiopterin. Regular outpatient follow-up care and measurement of the phenylalanine level in the blood are required. We aimed to analyze the economic burden of phenylketonuria on families and the state. The pa-tients with phenylketonuria were divided into three groups according to their treatment: a low-phenylalanine diet group (n= 50), a tetrahydrobiopterin group (n= 44) and a group taking tetra-hydrobiopterin together with the diet (n= 25). A comparative cost analysis was carried out. The annual economic burden to the state was calculated to average €18801±15345 and was lowest in the diet group, then in the tetrahydrobiopterin group and highest in the tetrahydrobiopterin+diet group (p < 0.001). Out-of-pocket costs amounted to €1531±1173 per year, and indirect losses aver-aged €2125±1930 per year for all families. The economic loss was significantly lower in the fami-lies taking tetrahydrobiopterin than in the other groups (p=0.001). The combined use of medical nutrition and BH4 treatments has been shown to increase the economic harm to the state. Reim-bursing low-protein products and increasing the rate of patients eligible for financial allowances may reduce the economic harm to families.

Salt stress is a major limiting factor for alfalfa yield due to its relatively low salt tolerance. High soil salinity adversely impacts alfalfa growth and development, leading to reduced yield. Melatonin (MT) is known to play a significant role in enhancing plant resistance to abiotic stresses. However, the mechanisms underlying melatonin-mediated abiotic stress responses, particularly salt stress, are not well understood. To address this gap, we conducted a study focusing on germinating alfalfa seeds under salt stress. Physiological indexes and transcriptomics analyses were carried out on the germinated seeds to investigate the effects of melatonin on alfalfa seedlings under salt stress conditions. Our results revealed that the application of melatonin led to an increase in shoot length and fresh weight of alfalfa seedlings under salt stress. Moreover, key physiological indexes such as peroxidase (POD) activity and glutathione (GSH) content were enhanced, while levels of malondialdehyde and superoxide anions decreased. Transcriptomic analysis identified a total of 2,131 differentially expressed genes in the salt-treated group, with 726 up-regulated and 1,405 down-regulated genes, while the MT-treated group showed 2896 differentially expressed genes, of which 1,097 were up-regulated and 1,799 were down-regulated. Further, KEGG enrichment analysis highlighted the enrichment of differentially expressed genes in pathways including flavonoid biosynthesis, ABC transporter, glutathione metabolism, and the MAPK signaling pathway, with these pathways more significantly enriched in the MT-treated group. These findings collectively suggest that melatonin plays a crucial role in alfalfa's response to salt stress and offer new insights into the genomic mechanisms underlying melatonin-mediated salt tolerance in alfalfa.

Source water quality is a key determinant of drinking water quality. The recast European Union 2020/2184 drinking water directive (DWD) introduced the obligation for comprehensive risk assessment in drinking water supplies, including the water source and incorporated new elements of natural origin in the list of parameters to be monitored. The current study is the first comprehensive assessment of 15 natural elements (B, Ba, Be, Ca, Co, K, Li, Mg, Mo, Na, Se, Sr, Ti, U and V) in 1155 (82%) Hungarian drinking water sources, including surface water, bank filtered and groundwater sources. Parameters posing a risk to health (Se, V and U) were typically below the lower limit of quantification (LOQ), but higher concentrations (max. 7.0, 17 and 41 µg/L, respectively) may occur in confined locations, the latter exceeding the DWD parametric value in one water supply. Li in a small geographical area, Mg and Ca in the majority of the water supplies reached the concentration range assumed to be protective to health. Water sources were grouped in 6 clusters based on their element distribution, some of them also showing clear geographical patterns. Water types were not differentiated, with the exception of karstic waters (dominated by Ca and Mg). None of the investigated parameters are expected to be a source of public health concern.

Salt stress is one of the major abiotic stresses that lead to crop yield reduction worldwide. Melatonin (MT), an endogenous hormone synthesized in plants, plays an important role in responding to abiotic stimuli such as drought, salinity, heat, cold, etc. However, the molecular mechanisms of MT-mediated abiotic stresses remain to be better understood. In order to explore the key genes and pathways of melatonin in alleviating salt stress, physiological and biochemical indicators as well as transcriptomics profile were conducted in alfalfa seedlings. The results showed that the germination rate, bud length and fresh weight of alfalfa seedlings added with melatonin were higher than those treated with salt alone. In addition, Malondialdehyde (MDA) and Superoxide anion (O2-) contents also displayed a decreasing trend. The activity and content of Superoxide dismutase (SOD)、peroxidase (POD) and Glutathione (GSH) increased to varying degrees. In order to further reveal the molecular mechanism of MT-mediated salt tolerance of alfalfa, transcriptome analysis was performed on alfalfa seedlings. 2,181 differentially expressed genes (DEGs) were obtained in the salt-treated group, including 780 upregulated genes and 1,401 down-regulated genes, while 4,422 DEGs were obtained in the MT group, among which 1,438 were upregulated and 2,984 were downregulated. By using GO functional annotation and KEGG pathway enrichment, we found that DEGs were mainly enriched in the biosynthesis of flavonoids, isoflavones, plant hormones, Glutathione (GSH), soluble sugars and other substances, as well as in the ABC transporter and MAPK signaling pathways. Among them, the DEGs in the MT group was more enriched in these pathways, suggesting that MT can combat salt stress by regulating the expression of genes related to phytohormone and antioxidant capacity, which has important reference value for the breeding of salt-tolerant alfalfa and other crops.

During 2021 and 2022 summers, we measured the total and dissolved (&lt; 0.45 mm) concentration of 25 elements in Utah Lake using Inductively Coupled Plasma Optical Emission Spectrometry (ICP-OES). Utah regulates twelve of these elements. ICP-OES sensitivity is at the ppb-level but is not the approved regulatory method. All regulations are for dissolved concentrations; except aluminum (Al) and phosphorus (P) which are for total recovery. We found total Al concentrations above allowable, but dissolved concentrations were well below allowable concentrations. We attribute high total concentrations to suspended clays. Dissolved copper (Cu) concentrations were below regulatory levels in 2021, but some samples were above regulatory levels in 2022. This could be related to the use of Cu-based algaecide treatments, or from other sources. Lead (Pb) data were inconclusive; dissolved Pb concentrations were well below the acute (1-hour average) limit, but the chronic concentration limit (4-hour average) is below the ICP-OES minimal detection limit. Arsenic (As) concentrations exhibit a seasonal trend that we attribute to groundwater inflows. This ppb-level study provides insight into regulated elements in Utah Lake previously not available due to the high sensitivity of the method and measurements of both total and dissolved concentrations.

The article addresses manufacturing structures made of biodegradable materials that can be successfully used as energy-absorbing liner of sports helmets of all kinds, replacing the previously used expanded polystyrene. The paper is focused on injection technological tests and tensile tests (in quasi-static and dynamic conditions) of several composites based on a PLA matrix with the addition of other biodegradable softening agents, such as PBAT and TPS. Next, the thin-walled elements (dimensions of 55 x 55 x 20 mm) were manufactured and evaluated using a spring-loaded drop hammer. The 60J impact energy was tested according to EN 1078 standard. The dynamic crushing testing included checking the influence of the materials temperature (-20, 0, 20, and 40 °C) and the impact velocity. The PLA15PBAT85 blend was selected as the most effective material in terms of its use as energy-absorbing liner for sport helmets.

In this work model of mirror elements equilibrium of the micromechanical components is developed, the behavior analysis of the mirror element of micromechanical mirrors in case changing of control voltages of electrostatic actuators is carried out, an expression for determining the maximum value of deflection voltage at which the snap-down effect will take the following form is obtained in case of the influence of the coefficient of the electrostatic rigidity of electrostatic actuators. The developed equilibrium model of mirror elements and the obtained results of modeling can be used at design of micromechanical mirrors with internal suspensions.

Nitrate and nitrite are the most extensively used food additives in the food industry for their multifunctional properties, and they have been in the spotlight for decades for its controversial back effects. The conversion of nitrate and nitrite to various nitroso compounds, specifically N-nitrosamine raises the question of the integrity of these additives. Nitrosamine is a well-known carcinogen and mutagen. A large number of studies demonstrate the carcinogenic effects of these salts. Are these findings credible? Nonetheless, the regulatory agencies approve its usage; is it biased? Are we feeding on the carcinogens in processed foods? The current work provides an insight into the basic and toxicological findings of the food additives -nitrate and nitrite.

Since the discovery of transposable elements (TEs) in Maize in the 1940s by Barbara McClintock [1] transposable elements have been described as junk, as selfish elements with no benefit to the host, and more recently as major determinants of genome structure and genome evolution. TEs are DNA sequences that are capable of moving to new sites in the genome and make additional copies while doing so. To limit the propagation of TEs, host silencing mechanisms are directed at transposon-encoded genes that are required for mobilization. The mutagenic properties of TEs, the potential of TEs to form new genes and affect gene expression, together with the host silencing mechanisms shape eukaryotic genomes and drive genome evolution. While TEs constitute more than half of the genome in many higher eukaryotes, transposable elements in the nematode C. ele-gans form a relatively small proportion of genome, about 15% [2]. Genetic studies of transposon silencing and the discovery of RNAi in C. elegans, propelled C. elegans to the forefront of studies of RNA-based mechanisms that silence TEs. Here, I will review the transposable elements that are present and active in the C. elegans genome, and the host defense mechanisms that silence these elements.

A replicated outdoor pot experiment was conducted in order to investigate the effect of different phytohormone and siderophore producing, and P-solubilizing bacterial species on spinach nu-trient uptake, nitrate concentration and nitrate reductase activity. The mentioned parameters were determined in spinach leaves (Spinacia oleracea L.), non-inoculated and inoculated with four plant growth–promoting actinobacteria (Streptomyces griseus (S1), Streptomyces albogriseolus (S2), Strep-tomyces aurantiacus (S3) and Streptomyces kanamyceticus (S4) under the influence of two sources of nitrogen fertilizers including potassium nitrate and urea (100 and 200 ppm). Inoculation with the strains increased spinach shoot fresh weight by 16%–43% over the control. Bacterial inoculation gave leaf chlorophyll increases of 15%–40%. Inoculation increased plant height by 2.2%–24.6% in spinach. A close reverse relationship between nitrate concentration and enzyme activity (r2= 0.87) was demonstrated. The measured parameter responses were variable and dependent on the in-oculant strain, with highest enzyme activity and lowest nitrate concentration exhibited in S2 (S. albogriseolus) inoculation. The source and application dose of nitrogen fertilizer had varied impact on measured parameter. The maximum phosphorous and iron concentration were measured by soil inoculation with S4 and applying 200 ppm nitrate potassium nitrogen fertilizer. Application of 200 ppm KNO3 nitrogen fertilizer with different Streptomyces strains showed the capability of S2 in decreasing nitrate content while protein content increased. In particular, the strains S2 and S4 have great potential in being formulated and used as biofertilizers.

To investigate this suitability of Black Mustard (Brassica Nigra L.) and Camelina (Camelina Sativa L.) for pulp manufacturing the nitrate-alkaline method was used. The non-wood plants were characterized by chemical analysis, especially lignin, cellulose, ash, extractives and alpha-, beta-, gamma-cellulose. The pulp was cooked in 6% nitric acid and then underwent the extraction by 5% sodium-hydroxide and neutralized by 1% acetic acid. The cooked pulp was characterized by delignification degree – Kappa number. The laboratory sheets were made from this cooked pulp and they were characterized by tensile index, breaking length, smoothness and compared with commonly available papers.

Contamination in coastal regions attributed to fluoride and nitrate cannot be disregarded, given the substantial environmental and public health issues they present worldwide. Maintaining water quality is crucial for environmental well-being. This comprehensive study was performed to assess the spatial as well as indexical water quality, identify contamination sources, and evaluate associated health risks pertaining to nitrate and flouride in AlHassa region, KSA. The physiochemical results revealed a pervasive pollution of the overall groundwater. The dominant water type was Na-Cl, indicating saltwater intrusion and reverse ion exchange impact. Spatiotemporal variations in physicochemical properties suggest diverse hydrochemical mechanisms, with geogenic factors primarily influencing groundwater chemistry. The groundwater pollution index varied between 0.8426 and 4.7172, classifying samples as moderately to very highly polluted. Similarly, the synthetic pollution index (in the range of 0.5021-4.0715) revealed that none of the samples had excellent water quality, with various degrees of pollution categories. Nitrate Health Quotient (HQ) values indicated chronic human health risks ranging from low to severe, with newborns being the most vulnerable. Household use of nitrate-rich groundwater for showering and cleaning did not pose significant health risks. Fluoride HQ decreased with age, and children faced the highest risk of fluorosis. The Hazard Index (HI) yielded moderate to high-risk values. Nitrate risks were 1.21 times higher than fluoride risks, as per average HI assessment. All samples fell into the vulnerable category based on the Total Hazard Index (THI), with 88.89% classified as very high risk. This research provides valuable insights into groundwater quality, guiding water authorities, inhabitants, and researchers in identifying safe water sources and vulnerable human populations. The results highlight the need for appropriate treatment techniques and long-term coastal groundwater management plans.

Hypertensive diseases of pregnancy (HDP) represent a global clinical challenge, affecting 5-10% of women and leading to complications for both maternal well-being and fetal development. At the heart of these complications is endothelial dysfunction, with oxidative stress emerging as a pivotal causative factor. The reduction in nitric oxide (NO) bioavailability is a vital indicator of this dysfunction, culminating in blood pressure dysregulation. In the therapeutic context, although antihypertensive medications are commonly used, they come with inherent concerns related to maternal-fetal safety, and a percentage of women do not respond to these therapies. Therefore, alternative strategies that directly address the pathophysiology of HDP are required. This article focuses on the potential of the nitrate-nitrite-NO pathway, abundantly present in dark leafy greens and beetroot, as an alternative approach to treating HDP. The objective of this review is to discuss the prospective antioxidant role of nitrate. We hope our discussion paves the way for using nitrate to improve endothelial dysfunction and control oxidative stress, offering a potential therapy for managing HDP.

The early 2-factor (E2F) family of transcription factors, including E2F1-8, plays a critical role in apoptosis, metabolism, proliferation, and angiogenesis within glioblastoma (GBM). However, the specific functions of E2F transcription factors (E2Fs) and their impact on the malignancy of Bevacizumab (BVZ)-responsive GBM subtypes remain unclear. This study used data from The Cancer Genome Atlas (TCGA) and Gene Expression Omnibus (GEO) to explore the impact of eight E2F family members on the clinical characteristics of BVZ-responsive GBM subtypes and possible mechanisms of recurrence after BVZ treatment.To predict the possibility of GBM patient survival and progression, we classified and comparedthe expression of E2Fs according to BVZ-responsive subtypes and employed a machine learning method-TreeBagger, one random forest algorithm. Multiple bioinformatics analyses have shown that the significant increased E2F8 post BVZ treatment may enhance the function of angiogenesis and stem cell proliferation, indicating one of the mechanisms of GBM recurrence after treatment. In addition, BVZ treatment in unresponsive GBM patients may potentially worsen disease progression. Our findings suggest that E2F family members play important roles in GBM malignancy and BVZ treatment response, highlighting their potential as prognostic biomarkers and therapeutic targets and recommending precise BVZ treatment for GBM patients.

This study uses simulation and experimental methodologies to explore the efficacy of bi-sectional horizontal kinetic shading systems (KSS) featuring horizontal fins in enhancing daylight comfort across various climates. Given the increasing energy demands and shifting climatic patterns, optimizing daylight levels while minimizing solar heat gain is vital. The paper introduces a bespoke horizontal bi-sectional KSS, simulated in three distinct climates—Wroclaw, Tehran, and Bangkok—using Climate Based Daylight Modelling methods with Ladybug and Honeybee tools in Rhino software. The study employs standard daylight metrics such as Useful Daylight Illuminance (UDI) and Daylight Glare Probability (DGP), along with custom metrics designed to capture the specific dynamics of the bi-sectional KSS. Initial simulations indicated that the KSS significantly improved daylight distribution and uniformity, reducing glare and over-illumination risks by av. 42.34%. Including KSS switching schedules, which are seldom detailed in similar research, enhances the reproducibility and understanding of findings. Subsequently, a physical reduced-scale mock-up of the bi-sectional KSS was tested under real-weather conditions in Wroclaw (lat. 51° N) during June-July 2024. The mock-up utilized two chambers: one equipped with the prototype of bi-sectional KSS and the second without any protection. The operation of fins was guided by two stepper motors controlled by a Python script running on a Raspberry Pi 3 minicomputer. The control chamber served to benchmark the bi-sectional KSS's efficiency by providing results that would be expected if no shading system were installed. The experimental outcomes supported the simulations, demonstrating the KSS's robustness in reducing high illuminance levels to the target comfort level, thus enhancing indoor visual comfort. The values below 3,000 lux were maintained for 68% of the time. However, it must be explicitly stated that during the June-July 2024 heat waves, the illuminance levels inside the test room momentarily exceeded the comfort threshold of 3,000 lux, reaching up to 4,674 lux. Through quantitative and qualitative analyses, the paper advocates for the broader application and further development of KSS as a climate-responsive shading system in diverse architectural contexts.

For a left module RM over non-commutative ring R, the notion for the class of nilpotent elements (nilR(M)) was first introduced and studied by SSevviiri and Groenewald . Moreover, Armendariz and semicommutative modules are generalizations of reduced modules and nilR(M)=0 in the case of reduced modules. Thus, the nilpotent class plays a vital role in these modules. Motivated by this, we present the concept of nil-Armendariz modules as a generalization of reduced modules and a refinement of Armendariz modules, focusing on the class of nilpotent elements. Further, we demonstrate that the quotient module M/N is nil-Armendariz if and only if N is within the nilpotent class of RM. Additionally, we establish that the matrix module Mn(M) is nil-Armendariz over Mn(R) and explore conditions under which nilpotent classes form submodules. Finally, we prove that nil-Armendariz modules remain closed under localization.

Air pollution has created a lot of problems in the developed and developing countries. To avoid or reduce these problems, constant monitoring of the air should be ensured. The conventional techniques is costly because it requires a lot of money and time consuming. Biomonitoring has been the alternative method. Moss, lichens and plants are biomonitors available to entrap air pollutants. The aim of this paper is to discuss one of the ways of monitoring air pollution – Moss bag technique. To do this, types, choice, preparation, handling of bags after preparation of moss were discussed. From the literatures consulted, it was discovered that there were differences in the techniques used by the researchers. In all, the use of mosses with emphasis on the employment of moss bag have proved to be a powerful tool in airborne particulate and toxic elements. To conclude, developing countries should focus more on this technique because it will reduce cost of air monitoring.

Polydiacetylene (PDA) inserted in films or in vesicles have received increasing attention due to PDA property to undergo a blue-to-red colorimetric transition along with a change from non-fluorescent to fluorescent upon application of various stimuli. In this review paper, the principle of the detection of various microorganisms (bacteria: directly detected or detected through the emitted toxins or through their DNA, and viruses) and of antibacterial and antiviral peptides based on these responsive PDA vesicles are detailed. The obtained analytical performances, when vesicles are in suspension or immobilized, are given and compared to those of the responsive vesicles mainly based on the vesicle encapsulation method. Many future challenges are then discussed.

Neuronal PAS domain protein 2 (NPAS2) is a hemeprotein comprising a basic helix-loop-helix domain (bHLH) and two heme-binding sites, the PAS-A and PAS-B domains. This protein acts as a pyridine nucleotide-dependent and gas-responsive CO-dependent transcription factor and is encoded by a gene whose expression fluctuates with circadian rhythmicity. NPAS2 can heterodimerize with ARNTL in the activating limb of the transcriptional/translational feedback loop operating the circadian clock circuitry. NPAS2 can functionally substitute for the core transcription factor and histone/protein acetylase CLOCK in the molecular clockwork endowing central oscillators in the suprachiasmatic nuclei of hypothalamus as well as in peripheral oscillators in the cell of other body tissues, such as the liver and kidney.

The Marun-Keu complex plays a significant role in understanding the geological evolution of the Ural orogen; however, it remains poorly understood. This study aims to provide insights into the complex's age, protolith composition, rock formation conditions, and its position in the region's history. The zircons from the host granitic gneisses are characterized by magmatic cores with an age of 470 Ma and metamorphic rims with an age of approximately 370 Ma. We suggest that the metamorphic rims were formed during eclogite metamorphism and that the metagranitoids hosting the eclogites experienced eclogite metamorphism simultaneously with the basic and ultrabasic rocks that are common in this area. Heterogeneous zircons were also isolated from the selvage of a pegmatite vein, in which four domains are distinguished, two to three of which can be identified within single grains, as follows: 1) igneous cores with an age of approximately 470 Ma and the geochemical characteristics of zircon crystallized in basic rocks; 2) zircons recrystallized during eclogite metamorphism with geochemical characteristics intermediate between those of the magmatic cores and true eclogitic zircon; 3) pegmatitic zircon, exhibiting the most sharply differentiated REE spectra of all four domains, characterized by a prominent positive Ce anomaly and a weakly expressed negative Eu anomaly; and 4) eclogitic zircon, observed in the form of veins and rims, superimposed in relation to the other three domains. The age of the latter three domains is within the error range and is estimated to be approximately 370 Ma. This indicates that the processes of eclogite metamorphism and the formation of pegmatites occurred at approximately the same time in the studied area.

The aim of this research involves investigating the elimination of nitrogen ions from groundwater through the application of dynamic permeable reactive barriers (PRB) utilizing A400-nZVI. The aim also implyies determining barrier parameters, as well as assessing the overall retention capacity of nitrogen ions through percolation with a potassium nitrate solution. The research involves obtaining zero valent iron nanoparticles (nZVI), which were synthesized and doped onto an anionic resin support material (A400) through the reduction reaction of ferrous ions with sodium borohydride (NaBH4). This was achieved by preparing a ferrous sulfate solution, contacting it with the ion exchange resin at various solid-liquid mass ratios, and gradually adding sodium borohydride under continuous stirring in an oxygen-free environment to create the A400-nZVI barrier. The outcomes of this study, focusing on the development of permeable reactive barriers composed of nanovalent iron and ion exchangers, demonstrate significant potential in purification processes when appropriately dimensioned. The research specifically evaluated the efficacy of NO3- removal using the A400-nZVI permeable reactive barrier, conducting laboratory tests that simulated a naturally stratified aquifer with high nitrate contamination.

Nitrogen (N) strongly affects plant growth and metabolism. For shikonin biosynthesis, although the ammonium toxicity phenomenon has been reported, the effects of nitrogen on the shikonin synthesis remains obscure. In this study, we carried out four different concentrations of NH4+ treatments on Arnebia euchroma hairy roots (AEHR) to clarify the influence of NH4+ on the growth and shikonin accumulation in A. euchroma and the possible mechanism. The results showed that compared with the 0% NH4+ treatment (only nitrate as nitrogen source), 10% NH4+ treatment increased the fresh weight and the dry weight of AEHR, and promoted the synthesis of shikonins; 20% NH4+ treatment started to show the inhibition effects on growth and shikonin accumulation of AEHR and 30% NH4+ treatment exhibited the strongest inhibition effects. With increased percentage of NH4+, AEHRs became shorter and thicker with more branches. To further elucidate the mechanism, we analyzed the time-course of nitrogen assimilation, gene expression level of key enzymes involved in the shikonin biosynthesis pathway, and contents of various endogenous hormones under NH4+ toxicity condition. Results indicated that auxin and cytokinin might regulate the growth and architecture of AEHR under NH4+ toxicity, and jasmonate level was reduced along with the inhibition of shikonin biosynthesis. This first comprehensive investigation into the effects of ammonium/nitrate ratio on shikonin biosynthesis not only provided valuable data for optimizing the in vitro culture and shikonin production in A. euchroma, but also suggested potential fertilizer strategies for its cultivation.

Copper-based nanoparticles were synthesized using the glycine–nitrate process (GNP) by using copper nitrate trihydrate [Cu(NO₃)₂‧3H₂O] as the main starting material and glycine [C₂H₅NO₂] as the complexing and incendiary agent. The as-prepared powders were characterized through X-ray diffraction (XRD), Brunauer–Emmett–Teller (BET) analysis, X-ray photoelectron spectroscopy, and scanning electron microscopy. Using Cu(NO₃)₂.3H₂O as the oxidizer (N) and glycine as fuel (G), we obtained CuO, mixed-valence copper oxides (CuO + Cu₂O, G/N = 0.3–0.5), and metallic Cu (G/N = 0.7). The XRD and BET results indicated that increasing the glycine concentration (G/N = 0.7) and reducing particle surface area increased the yield of metallic Cu. The effects of varying reaction parameters such as catalyst activity, catalyst dose, and H₂O₂ concentration on nonylphenol-9-polyethoxylate (NP9EO) degradation were assessed. With a copper‐based catalyst in a heterogeneous system, the NP9EO and total organic carbon removal efficiencies were 83.1% and 70.6%, respectively, under optimum operating conditions (pH, 6.0; catalyst dose, 0.3 g/L; H₂O₂ concentration, 0.05 mM). The results suggested that removal efficiency increased with an increase in H₂O₂ concentration but decreased when the H₂O₂ concentration exceeded 0.0.5 mM. Furthermore, the trend of photocatalytic activity was as follows: G/N = 0.5 > G/N = 0.7 > G/N = 0.3. The G/N = 0.5 catalysts showed the highest photocatalytic activity and resulted in 94.6% NP9EO degradation in 600 min.

Groundwater contamination by nitrate and organic chemicals (e.g. 1,4-dioxane) is a growing worldwide concern. This work presents a new approach for simultaneously treating nitrate and 1,4-dioxane, which is based on UV sensitization of nitrate and sulfite, and the production of reactive species. Specifically, water contaminated with nitrate and 1,4-dioxane is irradiated by a UV source (< 250 nm) at relatively high doses, to sensitize in-situ nitrate and generate HO•. This leads to the oxidation of 1,4-dioxane (and other organics), and the (undesired) production of nitrite as an intermediate. Subsequently, sulfite is added at an optimized time-point, and its UV sensitization produces hydrated electrons which reacts and reduces nitrite. Our results confirmed the effectivity of the proposed treatment: UV irradiation of nitrate (at > 5 mg N/L) efficiently degraded 1,4-dioxane, while producing nitrite at levels higher than 1 mg N/L (its MCL in drinking water). Adding sulfite to the process after 10 minutes of irradiation reduced the concentration of nitrite, without affecting the degradation rate of 1,4-dioxane. The treated water contained elevated levels of sulfate; albeit at much lower concentration than its MCL. Treating water contaminated with nitrate and organic chemicals (often detected concomitantly) typically requires several (expensive) treatment processes. The proposed approach may present a cost-effective alternative, employing a single system for the treatment of nitrate and organic contaminants

Cancer is a highly heterogeneous disease and remains a global health challenge affecting millions of human lives worldwide. Despite advancements in conventional treatments like surgery, chemotherapy, and immunotherapy, the rise of multidrug resistance, tumor recurrence, and severe side effects necessitates innovative therapeutic approaches. The complex nature of the tumor microenvironment (TME) further compromises the efficacy of traditional chemotherapy drugs. Recently, stimulus-responsive nanomedicines designed to target TME characteristics (e.g., pH, redox, enzymes) have gained attention for their potential to enhance anticancer efficacy while minimizing adverse effects. Among various nanocarriers, hydrogels are an interesting class of nanocarriers used in cancer therapy due to their high water content, adjustable mechanical characteristics, and ability to respond to external/internal stimuli. These properties make hydrogels an ideal nanocarrier for controlled drug release within the TME. This review comprehensively surveys the latest advancements in stimulus-responsive hydrogels for cancer therapy, exploring various stimuli-responsive mechanisms, including biological (e.g., pH, redox), chemical (e.g., enzymes, glucose), and physical (e.g., temperature, light), as well as dual- or multi-stimuli responsiveness. This review will offer novel perspectives on the development of stimulus-responsive hydrogels for cancer therapy.

Biomimetic stimuli-responsive materials can respond to various external stimuli in the form of structural or morphological transformations by actively or passively converting input energy into mechanical energy. They are the core element of soft actuators for typical smart devices like soft robots, artificial muscles, intelligent sensors and nanogenerators. While significant progresses have been made in bioinspired stimuli-responsive materials, they have not yet achieved the remarkable properties in biological systems. In this review, we will discuss recent advances in biomimetic stimuli-responsive materials that are instrumental for soft actuators. Different stimuli-responsive principles for soft actuators are firstly discussed, including fluidic, electrical, thermal, magnetic, light and chemical stimuli. We further summarize the state-of-the-art stimuli-responsive materials for soft actuators and explore the advantages and disadvantages of using electroactive polymers, magnetic soft composites, hydrogels, liquid crystal elastomers, shape memory alloys and chemical-responsive materials. Finally, we provide a critical outlook on the field of stimuli-responsive soft actuators, and emphasize the challenges in the process of their implementation to various industries.

Herein, we report a stimuli responsive hydrogel with inhibitory activity against Escherichia coli prepared by chemical crosslinking of carboxymethyl chitosan (CMCs) and hydroxyethyl cellulose (HEC). The hydrogels were prepared by esterification of chitosan (Cs) with monochloroacetic acid to produce CMCs which was then chemically crosslinked to HEC using citric acid as the crosslinking agent. To impart a stimuli responsiveness property to the hydrogels, polydiacetylene-zinc oxide (PDA-ZnO) nanosheets were synthesized in-situ during the crosslinking reaction followed by photopolymerization of the resultant composite. To achieve this, ZnO was anchored on carboxylic groups in 10,12-pentacosadiynoic acid (PCDA) layers to restrict movement of alkyl portion of PCDA during crosslinking CMCs and HEC hydrogels. This was followed by irradiating the composite with UV radiation to photopolymerize the PCDA to PDA within the hydrogel matrix so as to impart thermal and pH responsiveness to the hydrogel. From the results obtained, the prepared hydrogel had a pH dependant swelling capacity as it absorbed more water in acidic media as compared to basic media. Incorporation of PDA-ZnO resulted in a thermochromic composite responsive to pH evidenced by a visible colour transition from pale purple to pale pink. Upon swelling, PDA-ZnO-CMCs-HEC hydrogels had inhibitory activity against E. coli attributed to the slow release of the ZnO nanoparticles as compared to CMCs-HEC hydrogels.

This study focuses on examining the determinants of capital structure and the influence of taxes within Iran Khodro Company in the automobile industry from 2016 to 2023. The research analyzes the relationship between debt, taxes, and various company-specific factors. Findings indicate a direct relationship between taxes and debt, with financial leverage being the most significant element related to taxes. The study aims to provide valuable insights for managers and decision-makers in enhancing financial decision-making and shareholder wealth. Various studies have also been conducted on the impact of taxes and different factors on the capital structure of companies listed on the Tehran Stock Exchange, highlighting the importance of tax implications in financial decisions.

Global warming and climate change have been the major concern for multiple disciplines. Population growth, urbanization, and industrialization are major contributing factors to such a problem by escalating the use of fossil fuels to meet their energy demands. The building sector has the largest share in using the total globally produced energy and emitting tons of greenhouse gas emissions. Emerging eco-friendly technologies such as solar and wind energy harvesting are being extensively explored but still, they are insufficient. Nature-inspired technologies can be the solution to our problem. For instance, algae are microorganisms that use water, light, and CO2 to produce energy and sustain life. Exploiting such characteristics in the built environment is termed algae building technology, a very efficient and green application for a sustainable future. Algae-integrated façades show great versatility through biomass and energy production, wastewater treatment, shading, and thermal and acoustic insulation. In this paper, algae will be introduced as a robust tool toward a greener and more sustainable future, The algae-building technology and its implementation will be demonstrated. Steps for applying this sustainable approach in Egypt will be discussed.

Nitrate is rich in Mars sediments owing to long-term atmospheric photolysis, oxidation, and deposition coupled with a lack of leaching via rainfall. The Atacama Desert in Chile, which is similarly dry and rich in nitrate deposits, is used as a Mars analog in this study to explore the potential effects of high nitrate levels on microbial growth. Seven study sites sampled across an aridity gradient in the Atacama Desert were categorized into 3 clusters – hyperarid, intermediate, and arid sites, as defined by major elements in the regolith, associated biomass, and precipitation. Intriguingly, the distribution of nitrate concentrations in the shallow subsurface suggests that the buildup of nitrate is not solely controlled by precipitation. Correlations of nitrate with SiO2/Al2O3 and grain sizes suggest that sedimentation rates are also important in controlling nitrate distribution. At arid sites receiving more than 10 mm/yr precipitation, rainfall shows a stronger impact on biomass than nitrate does. However, high nitrate to organic carbon ratios are generally beneficial to N assimilation as evidenced both by soil geochemistry and enriched culturing experiments. This study suggests that even in the absence of precipitation on contemporary Mars, the nitrate levels are sufficiently high to benefit potentially extant Martian microorganisms.

Between 2011 and 2016 small-scale farm trials were run across three dairy regions of New Zealand (Waikato, Canterbury, Otago) to compare the performance of typical regional farm systems with farm systems implementing a combination of mitigation options most suitable to the region. The trials ran for at least three consecutive years with detailed recording of milk production and input costs. Nitrate leaching per hectare of the milking platform (where lactating cows are kept) was estimated using either measurements (suction cups), models, or soil mineral nitrogen measurements. Post-trial, detailed farm information was used in the New Zealand greenhouse gas inventory methodology to calculate the emissions from all sources; dairy platform, dairy support land used for wintering non-lactating cows (where applicable) and replacement stock, and imported supplements. Nitrate leaching was also estimated for the support land and growing of supplements imported from off-farm using the same methods as for the platform. Operating profit (NZ$/ha/year), nitrate leaching (kg N/ha/year), and greenhouse gas emissions (t CO₂-e/ha/year) were all expressed per hectare of milking platform to enable comparisons across regions. Nitrate leaching mitigations adopted in lower-input (less imported feed and N fertiliser) farm systems reduced leaching by 22 to 30 percent, and greenhouse gas emissions by between nine and 24 percent. The exception was the wintering barn system in Otago where nitrate leaching was reduced by 45 percent but greenhouse gas emissions were unchanged due to greater manure storage and handling. Important drivers of a lower environmental footprint are reducing nitrogen fertiliser and imported feed. Their effect is to reduce nitrogen surplus and feed flow through the herd and drive down both greenhouse gas emissions and nitrate leaching. Emission reductions in the lower-input systems of Waikato and Canterbury came at an average loss of profit of approximately NZ$100/t CO₂-e (three to five percent of industry average profit per hectare).

The principal aim of this descriptive-survey investigation is to ascertain the factors influencing individuals' choice to purchase organic commodities in Tehran. The statistical populace for this examination comprised all patrons of food retail establishments in Tehran, with the sample size determined using the Cochran formula for an unknown community size, involving the distribution of 30 questionnaires to customers (n=439). Data collection was carried out through a random sampling technique. The survey instrument consisted of a questionnaire with two sections consisting of general queries (7 questions) and specific inquiries (23 items) categorized into four dimensions (product, price, place, and promotion) for the clientele. The questionnaire's validity was confirmed through face and content validation, while its reliability was assessed utilizing Cronbach’s alpha. Data analysis was conducted using SPSS25 software, encompassing both descriptive and inferential statistical analyses. The results revealed a positive and significant correlation between customers' inclination to consume organic goods and the characteristics of the product, price, and promotion. However, no association was found between the propensity to consume organic products and location characteristics. Concerning contextual variables, a solely positive and significant correlation was identified between the willingness to purchase organic items and consumer income levels. No significant relationships were detected between other contextual variables and organic product consumption. A notable contrast was observed between respondents' gender and their readiness to buy organic products, while no significant variances were noted regarding age, income, occupation, and education in relation to the propensity to purchase organic commodities.

Over recent years, nanocarriers have played an ever-increasing role in clinical and biomedical applications owing to their unique physicochemical properties and surface functionalities. Lately, much effort has been directed towards the development of smart, stimuli-responsive nanocarriers that are capable of releasing their cargos in response to specific stimulus. These intelligent-responsive nanocarriers can be further surface-functionalized so as to achieve active tumor targeting in a sequential manner, which can be simply modulated by the stimuli. By applying this methodological approach, these intelligent-responsive nanocarriers can be directed to different target-specific organs, tissues or cells, and exhibit on-demand controlled drug release that may enhance therapeutic effectiveness and reduce systemic toxicity. Light, an external stimulus, is one of the most promising triggers for use in nanomedicine to stimulate on-demand drug release from nanocarriers. Light-triggered drug release can be achieved by light irradiation at different wavelengths, either in UV, visible or even NIR region, depending on the photophysical properties of the photo-responsive molecule embedded in the nanocarrier system, the structural characteristics and material composition of the nanocarrier system. In this review, we highlighted the emerging functional role of light in nanocarriers, with emphasis on light-responsive liposomes and dual-targeted stimuli-responsive liposomes. Moreover, we provided the up-to-date phototriggered targeting strategies and mechanisms of light-triggered drug release from liposomes and NIR-responsive nanocarriers. Lastly, we addressed the current challenges, advances, and future perspectives for the deployment of light-responsive liposomes in targeted drug delivery and therapy.

In Nature, it is common for living plants and non-living plant tissues to consist of materials with anisotropic multilayer and non-homogenous structure. The structure of tissues determines their self-shaping and self-folding capabilities in response to a stimulus in order to activate different functionalities. Predetermined movements are realized according to changes in environmental conditions, which trigger the fibrous anisotropic structure of the plants’ material. In this study, we present the fabrication process of low-cost anisotropic multilayer materials that are capable of realizing complex movements caused by small temperature changes (<40 ^oC). The mismatch in the thermo-mechanical properties between three or more anisotropic thin layers creates responsive materials that alter their shape owing to the developed internal stresses. Isotropic layers can perform only bending movements, whereas anisotropic multilayer materials can perform bending, twisting or complex combined modes. The movements of the material can be controlled by forming anisotropic homogenous metallic strips over an anisotropic polymer. As a result, inexpensive responsive materials can be developed to passively react to a very broad range of thermal requirements. We studied the major parameters that affect the sensitivity of the developed materials, as well as their failure modes and crack formation under thermal fatigue conditions.

The boosted interest in the use of rare earth elements (REEs) in modern technologies had also increase the necessity of their recovery from various sources, including raw materials and wastes. Though Hydrometallurgy plays a key role in these recovery processes, some drawbacks (apparent or not) of these processes, had led to the development of a more environmental friendship subclass named Solvometallurgy, in which non-aqueous solvents substituted to the aqueous media of the hydrometallurgical processing. The non-aqueous solvents chosen for these usages are, besides ionic liquids (ILs), the so-named Deep Eutectic Solvents (DEEs). The utilization of DEEs included the leaching of REEs from the different sources containing them, and also in the separation-purification steps necessary for the yielding of these elements, normally as oxides or salts, in the most purified form. This work reviewed the most recent literature (2023 year) about the utilization of deep eutectic solvents in the recovery of REEs from various sources, and in the coupling of these two (DESs and REEs) to derived compounds to be used in other fields.

Although various atmospheric corrosion simulation models have been developed that give good results, industrial environments are still challenging. This paper aims to investigate the effect industrial atmospheres in Bor on the mechanical properties of structural steel S235JR and to create a constitutive model and also laboratory experimental conditions that will give the best results as an accelerated corrosion test. Atmospheric corrosion tests lasted six months, using sites close to the Electrolytic Refining Plant and Sulphuric Acid Plant, as well as air quality monitoring stations at a remote location in the city of Bor. The laboratory experiments included a salt chamber test lasting 120 h and 240 h and immersing the specimen in the electrolyte from the Electrolytic Refining Plant for 30 days. The results were compared with the standard specimens stored in the laboratory. The X-ray diffraction (XRD) method was used to identify the composition of corrosion products. The scanning electron microscopy (SEM) analysis was applied to analyze the fracture surfaces of the specimens. The use of the Complete Gurson Model (CGM) described the tensile characteristics of the corroded specimens. The study has shown that an enhanced acceleration model and conditions could be developed using numerical analysis of the test results.

Newborn screening (NBS) is hailed as a public health success, but little is known about long-term outcomes following a positive newborn screen. There has been difficulty gathering long-term follow-up (LTFU) data consistently, reliably, and with minimal effort. Six programs developed and tested a core set of minimal LTFU data elements. After an iterative data collection process and the development of a data collection tool, the group agreed on minimal LTFU data elements. The denominator captured all infants with an NBS diagnosis, accounting for children who moved or died prior to the follow-up year. They also agreed on three LTFU outcomes: if the child was still alive, had contact with a specialist, and received appropriate care specific to their diagnosis within the year. The six programs representing NBS public health programs, clinical providers, and research programs provided data across multiple NBS disorders. In 2022, 83.8% (563/672) of the children identified by the LTFU programs were alive and living in the jurisdiction; of those, 92.0% (518/563) saw a specialist, and 87.7% (494/563) received appropriate care. The core LTFU data elements can be applied as a foundation to address the impact of early diagnosis by NBS within and across jurisdictions.

Preventing the rebound of black and odorous water bodies is critical for improving the ecological environment of water bodies. This study investigated the effect and mechanism of in-situ improvement of sediment microenvironment by nitrate in tailwater of wastewater treatment plants combined with aerobic denitrifying bacteria under low-DO regulation (TailN+CFM+LDO). On the 60th day of remediation, the dissolved oxygen and oxidation-reduction potential in the overlying water increased to 5.6 mg/L and 300 mV, respectively, the acid volatile sulfide in the sediment decreased by 70.4%, and the organic matter in the sediment was reduced by 62.7%, in which the HFOM was degraded from 105 g/kg to 56 g/kg, and the potential risk of water reverting to black and odorous conditions significantly decreased. Amplicon sequencing analysis revealed that the relative abundance of electroactive bacteria Thiobacillus and Pseudomonas with denitrification capacity was found to be significantly higher in the TailN+CFM+LDO group than in the other remediation groups. Functional prediction of 16S sequencing results indicated that both the quantity and activity of critical microbial enzymes involved in nitrification and denitrification processes could enhance in the TailN+CFM+LDO group. These results improved our understanding of the improvement of the sediment microenvironment and could thus facilitate its application.

Groundwater plays a pivotal role as the largest potable water sources in Bangladesh. However, the quality of the groundwater faces challenges due to xenobiotic compounds in it. Excess amount of arsenic (As) has already been found in groundwater in many parts of Bangladesh. Thus, this study was conducted to assess the water quality and associated human health risk in central Bangladesh. A total of 99 groundwater samples from the central part of Bangladesh were analyzed to assess human health risk due to high level of nitrate (NO3-) and other trace elements i.e. arsenic (As), iron (Fe), and manganese (Mn). It was found that NO3- concentration (253.17 mg/L) in the groundwater samples exceeds the recommended guideline value by the WHO (50 mg/L). Moreover, this study area also characterized with elevated concentration of As (19.44 µg/L), Fe (811.35 µg/L), and Mn (455.18 µg/L) in the groundwater. Non-carcinogenic human health risk was calculated by justifying HQ (Hazard Quotient) and HI (Hazard Index) and attributed potential conjunctive human health risks due to NO3-, As, Fe and Mn in the study area. Moreover, high carcinogenic risk was found due to As contamination in the groundwater samples in the study area.

Water pollution is the main problem in the current scenario which is being faced by mankind due to the industrial and commercial effects. Industrial effluents contain heavy metals and inorganic ions like nitrates and phosphate ions. These ions are being included in waterways through industrial runoff. When the concentration of these hazardous pollutants increases in aquatic flora and fauna causes severe health problems. So remediation of these toxicants from water reserves is of chief importance. Conventional processes along with modern processes are being used for the treatment of industrial wastes. Photo-degradation is a modern method used for the degradation of inorganic ions due to its environmentally friendly nature and cost-effectiveness. In a recent study Aluminum oxide (Al2O3) nanoparticles were synthesized via a green approach at different pH by using Cymbopogan citratus (lemongrass) plant extract and these nanoparticles were used for the removal of inorganic ions from wastewater. The nanoparticles of different pH showed different % degradation of the inorganic ions in acidic medium removal of inorganic waste was less, in basic media % degradation was more as compared to acidic media but maximum % degradation was observed in neutral media like that average % degradation 91% and 81% was observed for nitrate and phosphate ions. The maximum absorbance occurred at 212nm and Al2O3 nanoparticles showed absorbance from 210nm-217nm. The R2 values of pseudo1st, 2nd, and BMG models were 0.956, 0.837, 0.7007 0.95, 0.896, and 0.756 for the nitrate and phosphate ions. Characterizations of synthesized particles were investigated by using UV-visible spectroscopy and other analytical methods like X-ray diffraction (XRD) and Fourier transform infrared spectroscopy (FTIR). The statistical analyses were done using Simple Linear regression (SLR).

The global oil and gas exploration targets are gradually moving towards a new field of oil and gas accumulation with nano pore throats, ranging from millimeter scale to micro nano pore throats.There are difficulties in fluid transport in nano confined pore throats, such as strong adsorption, which greatly increases the difficulty of starting crude oil.Therefore, it is necessary to construct a nanoscale fluid with strong diffusion and dispersion, and improve its permeability, suction, and displacement capabilities.This article develops a carbon dioxide responsive graphene dot type surfactant.By characterizing its structure, physical and chemical properties, and conducting infiltration simulation experiments, its infiltration and drainage ability in nanopore throats is elucidated.Infrared spectrum measurement shows that after functional modification exhibit new characteristic peaks at 1600 cm-1 to 1300 cm-1, considering the N-H plane stretching characteristic peak.The fluorescence spectra showed that the fluorescence intensity of F-GQDs was increased after functional modification, which indicated that F-GQDs was successfully synthesized.Through measurements of interfacial activity and adhesion work calculations, the oil-water interfacial tension can achieve ultra-low values within the range of 10-2 to 10-3 mN/m. Oil sand cleaning experiments and indoor simulations of spontaneous imbibition in tight cores demonstrate that F-GQDs exhibit effective oil washing capabilities and a strong response to carbon dioxide. When combined with carbon dioxide, the system enhances both the rate and efficiency of oil washing.Imbibition recovery can reach more than 50%.The research results provide a certain theoretical basis and data reference for the efficient development of tight reservoirs.

A tetraphenylethylene-derived compound, TPEPhDAT, has been prepared by successive Suzuki-Miyaura coupling and ring-closing reactions. This compound exhibits aggregation-induced emission (AIE) properties in the DMSO/MeOH system, with a fluorescence emission intensity in the aggregated state that is 5-fold higher than that of its counterpart in a dilute solution. Moreover, the diaminotriazine structure of the molecule is a good acceptor of protons, and thus the TPEPhDAT molecule exhibits acid-responsive fluorescence. TPEPhDAT was protonated by trifluoroacetic acid (TFA), leading to a fluorescence quenching, which was reversibly restored by treatment with ammonia (On-Off switch). Time-dependent density functional theory (TDDFT) computational studies have shown that protonation enhances the electron-withdrawing capacity of the triazine nucleus and reduces the bandgap, producing a more intense intramolecular charge transfer (ICT), thus leading to fluorescence quenching. MeOH can easily remove the protonated TPEPhDAT, and this acid-induced discolouration and erasable property can be applied in anti-counterfeiting.

In this paper, a method for the preparation of ultrasound-responsive microgels was developed based on RAFT-HDA dynamic covalent bonding. First, a styrenic cross-linked network was suc-cessfully prepared by DA reaction between phosphoryl dithioester and furan using double-ended BDEPDF as RAFT reagent mediated St polymerization as double-ended dienophile linker and co-polymer of FMA and St as dienophile. Subsequently, the microgel system was constructed by the HDA reaction between phosphoryl disulfide and furan groups using the copolymer of polyethylene glycol monomethyl ether acrylate (OEGMA) and FMA as the dienophore building block and hy-drophilic segment, and the polystyrene pro-dienophile linker as the cross-linker and hydrophobic segment. The number of furans in the dienophile chain and the length of the dienophile linker were regulated by RAFT polymerization to investigate the effects of single-molecule chain functional group degree (f), furan/dithioester ratio (r), and hydrophobic linker length (D) on the microgel system. These microgels can achieve the reversible transformation of materials under force re-sponsiveness, and the steps are simple and adaptive, which are expected to show important po-tential applications in the fields of biomedical materials and adaptive electrical materials.

Solid tumors are composed of a highly complex and heterogenic microenvironment, with increasing metabolic status, playing a crucial role in the clinical therapeutic outcome of conventional treatments and innovative tumor nanomedicines. Scientists, have devoted great effort in conquering the tumor microenvironment (TME) challenges, in respect of effective drug accumulation and activity in tumor site, overcoming the obstacles of abnormal vasculature, dense stroma and extracellular matrix, hypoxia, and pH gradient acidosis. In this conquest, nanomedicines targeting distinct TME features have flourished, in order to increase site specificity and deep penetration, for effective antitumor activity, and further reprogram TME promoting suppression of cancer stem cells and metastasis. Thereby, several successful nanomedicine therapeutics have been under clinical trials, and further applied in clinical practice. Various novel strategies have been employed in preclinical studies and clinical trials, among which nanomedicines based on biomaterial, that have shown great promise in improving the therapeutic efficacy, reducing side effects, and promoting synergistic activity for TME targeting. In this review, we have focused on the targeting mechanisms for solid TME by nanomedicines based on the application of natural and synthetic biomaterials. We have described critical formulations that have been considered for the design of stimuli-responsive nanomedicines for TME. The development of such systems, has significantly advanced the application of biomaterials, in combinational therapies and in immunotherapies, for improved effectiveness.

Stimuli-responsive polymeric materials have attracted significant attentions in a variety of high-value-added and industrial applications during the past decade. Among various stimuli, light is of particular interest as a stimulus due to its unique advantages such as precisely spatiotemporal control, mild conditions, ease of use, and tunability. In recent years, a lot of effort toward synthesis of biocompatible and biodegradable polypeptide has resulted in many examples of photo-responsive nanoparticles. Depending on the specific photochemistry, those polypeptide derived nano-assemblies are capable of crosslinking, disassembling, or morphing into other shapes upon light irradiation. In this mini-review, we aim to assess the current state of photo-responsive polypeptide based nanomaterials. First, those “smart” nanomaterials will be categorized by their photo-triggered events (i.e., crosslinking, degradation, and isomerization) which are inherently governed by photo-sensitive functionalities including o-nitrobenzyl, coumarin, azobenzene, cinnamyl, and spiropyran. In addition, the properties and applications of those polypeptide nanomaterials will be highlighted as well. Finally, the current challenges and future directions of this subject will be evaluated.

A heterobifunctional reactive oxygen species (ROS)-responsive linker for directed drug assembly onto and delivery from a quantum dot (QD) nanoparticle carrier was synthesized and coupled to doxorubicin using EDC/sulfo-NHS coupling. The doxorubicin conjugate was characterized using ¹H NMR and LC-MS and subsequently reacted under conditions of ROS formation (Cu²⁺/H₂O₂) resulting in successful and rapid thioacetal oxidative cleavage which was monitored using ¹H NMR. The deprotected amine linker is amenable to peptide or protein conjugation prior to QD assembly or to direct conjugation to cognate reactive groups on ligands that cap the QD surface.

Green and sustainable electrocatalytic conversion of nitrogen-containing compounds to ammonia are currently in high demand in order to replace the eco-unfriendly Haber-Bosch process. Model catalysts for the nitrate reduction reaction were obtained by electrodeposition of metal Co, Fe and bimetallic Fe/Co nanoparticles from aqueous solutions onto a graphite substrate. The samples were characterized by the following methods: SEM, XRD, XPS, UV-vis spectroscopy, cyclic (and linear) voltammetry, chronoamperometry and electrochemical impedance spectroscopy. Besides, the determination of electrochemically active surface was also performed for all electrocatalysts. The best electrocatalyst was a sample containing Fe-nanoparticles on the layer of Co-nanoparticles, which showed the Faradaic efficiency 58.2% (E=-0.785 V vs. RHE) at the ammonia yield rate of 14.6 μmol h-1 cm-2. An opinion was expressed on elucidation of the mechanism of coordinated electrocatalytic action of a bimetallic electrocatalyst. This work can serve primarily as a starting point for future investigations on electrocatalytic conversion reactions to ammonia using model catalysts of the proposed type.

With the rapid development of cities in northwest China, there has been an increasing focus on groundwater pollution in plateau cities, specifically the common occurrence of nitrate pollution. The special climatic, geological, and geomorphological characteristics of plateau and river valley cities contribute to distinct groundwater chemical characteristics. Therefore, the formation and evolution process of groundwater nitrate contamination differs from that of plain cities. To explore these issues, we conducted an analysis of eight major ions in various groups of water samples from rivers, springs, and groundwater in Haidong. By utilizing factor analysis and correlation analysis, we were able to identify the characteristics and formation of groundwater chemistry and nitrate pollution in Haidong. Our findings reveal that the chemical characteristics of groundwater in Haidong are primarily controlled by rock weathering, mineral dissolution, and evaporation, leading to the formation of highly mineralized groundwater. Additionally, the excessive nitrate content in certain areas is a result of domestic sewage discharge and agricultural fertilizer use, exceeding Chinese drinking water health standards. Furthermore, for cities located in valleys, the geological structure significantly impacts the nitrate content of groundwater in different regions. Areas with obstructed groundwater flow tend to have higher nitrate levels, while regions with unobstructed groundwater experience lower nitrate concentrations. Notably, shallow groundxwater is more vulnerable to nitrate pollution compared to deep groundwater. This study holds great significance in understanding the chemical characteristics of groundwater and the formation and evolution of nitrate pollution in highland river valley cities.

High nitrate and fluoride contamination in groundwater cause a variety of disorders, including methemoglobinemia, teratogenesis, and dental and skeletal fluorosis. The present work assesses the non-carcinogenic health risks posed by nitrate and fluoride in infants, children, and adults using the USEPA method. Groundwater samples were collected from 36 wells and boreholes in three central Saudi Arabia study areas. Nitrate concentrations varied from 0.70 to 47.00 mg/L. None of the 36 studied boreholes had nitrate levels that exceeded WHO guidelines (50.00 mg/L). Fluoride ranged from 0.63 to 2.00 mg/L, and 30.55% of the fluoride samples (11 out of 36) exceeded the WHO recommendations for acceptable drinking water (1.5 mg/L). The average hazard index (HI) values for adults, children, and infants were 0.99, 2.59, and 2.77, respectively. Water samples surpassed the safety level of 1 for adults, children, and infants at 44.44, 97.22, and 100%, respectively. Accordingly, water samples from Jubailah and a few from Wadi Nisah may expose infants, children, and adults to non-cancer health concerns. Infants and children are more vulnerable to non-carcinogenic health risks than adults, possibly due to their lower body weight.

In this work, silver nanoparticles (AgNPs) were synthesized rapidly and eco-friendlily using the extract of Mulberry leaves and aqueous solution of silver nitrate without any toxic chemical [1,2]. The Mulberry leaves extract acts as both reducing agent and stabilizing agent. The UV-Vis spectrum shows peak at 430 nm. The TEM image of synthesized AgNPs sample shows spherical shaped particles whose size range from 15 to 20 nm. TEM image of nano silver solution sample synthesized by microwave assisted method shows nearly spherical particles with an average particle size of 10 nm. The absorption UV-vis spectrum of silver nanoparticles synthesized by microwave assisted method (AgNPsmw) shows a sharp absorption band around 415 nm. After two month storage of AgNPsmw, the absorption spectrum of AgNPsmw was taken again. The UV-Vis spectrum shows negligible peak changes of silver nanoparticles have occurred after two months of storage. The synthesized AgNPs material could be used as an antimicrobial, used in the field of textile and in wastewater treatment.

The Theory of differences between elements explains the reasons for the differences in physical concepts between different elements, such as quantum physics and the Theory of general relativity, being explained through observations. Thus, it is possible to conclude from the observations that the differences are motivated by the reactions between the elements, by the composition of the elements, and by the influence of the spaces that promote losses and gains of characteristics; therefore, there is no general similarity between quantum physics and the general Theory of relativity. The study aims to understand the elements and their physical concepts that make up the Universe.

Hund's rule of maximum multiplicity is a powerful empirical tool for determining the electron population of electronic shells. It was recently discovered that it is also the rule of minimum Shannon entropy. This study extends these findings to the Aufbau rule and discusses them from the perspective of emergent dimensionality, providing a monotonically increasing entropy function. We observed that some elements that violate the Aufbau rule have the same entropies in the actual and Aufbau electron configurations. On the other hand, lower entropies of all actual elements' configurations are associated with higher or equal numbers of unpaired electrons in these configurations compared to the Aufbau configurations. The only exception to this rule is palladium.

The recently defined and yet rather new topic of Healthy aging is gathering more attention on the global stage. With world’s population getting older - it is rapidly becoming very important to develop and maintain functional abilities in older age and develop mechanisms to protect senior population from chronic diseases. One of the most effective components, as well as, one may call - process involved in, and strongly associated with aging is recently discovered and Nobel prize awarded - nitric oxide as a signaling molecule, which followed by later discoveries showed to have a positive metabolic, immune and anti-inflammatory effects. One of the most debated topics of the last decade in the scientific community is nitrates, one of the pathways involved in nitric oxide production. Thus, the objective of this study was to evaluate effect of different potassium nitrate concentrate supplementation on Drosophila melanogaster longevity. 0,5-3% potassium nitrate medium was analyzed on the life span and motor function in different groups consisting of 100 females fruit flies each. In this assay, female fly species supplemented with potassium nitrate diet showed life span increase by 18.6% and 5.1% with 1% and 2% KNO3- respectively with a positive impact on locomotor function. In conclusion, we found that low concentration of potassium nitrate medium increased lifespan and locomotor function in Drosophila melanogaster.

In recent years, cancer therapy has witnessed significant advancements, with a focus on personalized and targeted treatment strategies. One promising approach involves the use of stimuli-responsive biomaterials for site-specific drug release. Among these biomaterials, pH, and redox-triggered polymer-nano composites have gained immense attention due to their ability to respond to the specific tumor microenvironment, enhancing therapeutic efficacy while reducing off-target effects. Cancer cells often exhibit anomalous biochemical properties, attributed to lower cytosolic pH (acidic) and elevated redox potential through the epitomized upregulation of undesired genes. Such biological process substantially imbalance the level ions (protons) and biological thiols glutathione (GHS) in the cytoplasm as well as in the subcellular organelles. Superfluous accumulation of ions and redox imbalance is associated with proliferation, invasion, and growth of tumor. Because of high surface area, deep tissue penetration capability, higher hydrophilicity, hydrophobic interior for drug/gene efficient loading, biocompatibility and site-specific targeting efficiency, functionalized polymer nanocomposites are superior to conventional small molecular materials. Paradoxically conventional methods of drug delivery aided therapeutics accompanied with inherent drug/genes are encapsulated in biocompatible carrier or suitable transfecting agents generally suffered with low bioavailability, uncontrolled drug release, low cellular penetration, cellular internalization, toxicity, and poor drug loading efficiency. To overcome these issues, recently various multifunctional nanomaterials were developed, based on synergistic stimuli responsive aided drug release in a specified cellular or subcellular system. High therapeutic efficacy, of nanoparticles (NPs) mainly associated with surface functionalization through biocompatible polymeric materials, site-specific targeting units accompanied with stimuli responsive components. Followed by therapeutically important drug or genetic materials were loaded into NPs either in covalent or non-covalent approach. Intriguingly, combined pH and redox dual stimuli based functional materials specially based on polymeric nanocomposites for cancer therapeutics scarcely reported. This article provides the recent progress in pH and redox-responsive polymer-nano composites for site-specific drug delivery in cancer therapy. It explores design principles, fabrication methods, mechanism of action, and prospects of these dual-stimuli responsive biomaterials.

Patients with lean NAFLD make up an increasing subset of liver diseases. The association between lean NAFLD and feutin-A, which serves as a hepatokine and adipokine, has never been examined. Our study aimed to explore the association of serum fetuin-A among lean and nonlean patients. The study comprised 606 adults from the community, stratified into lean or nonlean (BMI </≥ 24 kg/m2) and NAFLD or non-NAFLD (scoring of ultrasonographic fatty liver indicator, US-FLI ≥ 2/<2). Multivariate logistic regression analyses were performed to estimate the odds ratio of having NAFLD among the tertiles of fetuin-A after adjustment. The least square means were computed by general linear models to estimate marginal means of the serum fetuin-A concentrations in relation to the NAFLD groups. The OR of having NAFLD for the highest versus the lowest tertile of fetuin-A was 2.62 (95% CI: 1.72-3.98; P for trend<0.001). Stratifying by BMI, the OR of having lean NAFLD for the highest versus the lowest tertile of fetuin-A was 2.09 (95% CI: 1.09-3.98; P for trend 0.026), while nonlean NAFLD had no significant association with the fetuin-A gradient after adjustments. Fetuin-A was positively associated with lean NAFLD after adjusting for central obesity and insulin resistance.

Rural landscapes are acknowledged for their potential to restore human health due to their natural characteristics. However, few studies have systematically analysed the impact of naturalness, landscape types, and combinations of landscape elements on restorativeness using both subjective and objective measurements. This study investigated the restorative effects of various rural landscapes in Guangzhou, employing electroencephalography and eye-tracking technologies to record physiological responses and using the Restorative Components Scale and the Perceived Restorativeness and Naturalness Scale to evaluate psychological responses. The results indicated the following: (1) There was a significant positive correlation between perceived naturalness and restorativeness, surpassing the impact of actual naturalness. (2) Different landscape types had a varying impact on mental health at the equal perceived naturalness. Natural forest landscapes and artificial forest landscapes exhibited the most substantial restorative effects among the natural and semi-natural landscapes examined, respectively, while settlement landscapes showed the highest restorative potential among the artificial landscapes. (3) Restorative properties varied across landscape elements, with identical elements yielding different benefits in different environments. Trees and water significantly enhanced restorativeness, whereas constructed elements such as roads and infrastructure reduced it. This study provides a scientific basis for restorative rural landscape design to enhance mental health and well-being.

innate and adaptive immune responses lead to wound healing by regulating a complex series of events promoting cellular cross-talk. An inflammatory response is presented with its characteristic clinical symptoms: heat, pain, redness, and swelling. Some smart thermo-responsive polymers like chitosan can be used to create biocompatible and biodegradable scaffolds with 3D architectures similar to human structures, allowing their efficient and safe use as tissue engineering and drug delivery systems in chronic wounds. Locally heated tumors above polymer lower critical solution temperature can induce its conversion into a hydrophobic form, enhancing drug release until the thermal stimulus is gone, where a lower release is due to the swelling of the material. This paper integrates the relevant reported contributions of bioengineered scaffolds for thermo-responsive drug delivery in wound healing. Therefore, we present a comprehensive review that aims to demonstrate the capacity of these systems to provide spatially and temporally controlled release strategies for one or more drugs used in wound healing. In this sense, the novel manufacturing techniques of 3D-printing and electrospinning are explored for the tuning of their physicochemical properties to adjust therapies according to the patient’s convenience, as well as reduce drug toxicity and side effects.

Hybrid microparticles based on an iron core and amphiphilic shell have been prepared to respond simultaneously to external (magnetic and ultrasounds field) and internal (pH) stimuli for delivery of the anticancer drug doxorubicin. The microparticles have been prepared in three main steps; including surface modification of the iron core followed by conjugation with the amphiphilic chitosan and drug loading. The particles demonstrate spherical shape and dimension in the range 1-3 m with tunable surface charge by changing the pH of surrounding environment. The microparticles demonstrate good stability in simulated physiological solutions and able to allocate up to 400 g of drug per mg of bare carrier. The response to ultrasound and the changes in the shell structure when exposed to different pH allows to control the doxorubicin release. In vitro cytotoxicity tests performed on fibloblast NIH/3T3 demonstrate a reduction in the cell viability when doxorubicin was administrated by microparticles compared to the free formulation; in particular when ultrasound were applied. The bare microparticles demonstrate cytocompatibility and hemocompatibility up to 50g/mL and 60 g/mL, respectively.

The coexistence of SAH with T2DM is a common comorbidity. In this present study, we investigated the link between altered plasma antioxidant trace elements (ATE: Manganese, Selenium, Zinc and Copper) and fatty acids ratio (FAR: polyunsaturated/saturated) imbalance as transition biomarkers between vascular pathology (SAH) to metabolic pathology (T2DM). Our data revealed strong correlation between plasma ATE and FAR profile which is modified during SAH-T2DM association compared to healthy group. This relationship is mediated by lipotoxicity (simultaneously prominent visceral adipose tissue lipolysis, significant flow of non-esterified free fatty acids release, TG-Chol-dyslipidemia, high association of Total SFA, Palmitic acid, Arachidonic acid and PUFA 6/ PUFA 3; drop in tandem of PUFA / SFA and EPA+DHA); oxidative stress (lipid peroxidation confirmed by TAS depletion and MDA raise, concurrently drop of Zn/Cu-SOD, GPx, GSH, Se, Zn, Se/Mn, Zn/Cu; concomitantly enhance Cu, Mn and Fe); endothelial dysfunction (endotheline-1 increase); athero-thrombogenesis risk (concomitantly raise of ApoB100/ApoA1, Ox-LDL, tHcy and Lp(a)) and inflammation (higher of Hs-CRP, Fibrinogen and Ferritin). Our study open to new therapeutic targets and to better dietary management, such as to establish dietary ATE and PUFA 6 / PUFA 3 or PUFA / SFA reference values for atherosclerotic risk prevention in hypertensive-diabetics patients.

The theory says that the first things to exist in the universe and the current moment were driven by an imperative need; that is, the intensities of the physical concept specify influence the existence of elements and facts based on the countless observations in physical spaces in relation to elements and facts. The existence of mandatory elements in space is motivated by the characteristics of the spaces that offer conditions for such an obligation. The theory states that the universe did not arise by chance; that is, the universe emerged through determination influenced by its surroundings. The objective of the study is to help explain the elements and facts of the universe from its origins to the present.

Repetitive elements are a major component of DNA sequences due to their ability to propagate through the genome. Characterization of Metazoan repetitive profiles is picking up, however, current pipelines are failing to identify a significant proportion of divergent repeats in non-model organisms. The order Decapoda, for which repeat content analyses are largely lacking, is characterized by extremely variable genome sizes that suggest an important presence of repetitive elements. Here we developed a new standardized pipeline to annotate repetitive elements in non-model organisms, which we applied on 20 Decapoda and 6 other crustacean genomes. With our new tool we identify 10% more repetitive elements than standard pipelines. Repetitive elements were more abundant in Decapoda species than in other crustaceans, with an incredibly large number of highly repeated satDNA families. Moreover, we demonstrated a high correlation between assembly size and transposable elements and a different repeat dynamics between Dendrobranchiata and Reptantia. The patterns of repetitive elements largely reflect the phylogenetic relationships of Decapoda and the distinct evolutionary trajectories within Crustacea. In summary, our results highlight the impact of repetitive elements on genome evolution in Decapoda and the value of our novel annotation pipeline, which will provide a baseline for future comparative analyses.

Transposable elements (TEs) ubiquitously exist in the human genome, and some have the ability to copy and paste themselves to other locations, resulting in new insertions. Organisms have evolved with mechanisms and machineries to repress such activity. TEs are also co-opted for beneficial functions by the host and are thus maintained in the genome. During the lifetime of humans, aberrant TE activity might cause or contribute towards diseases including neurological conditions such as Alzheimers Disease (AD) and cancer. While inflammatory pathways linked to TEs may be a part of the disease pathology, on the other hand altered TE activity involving inflammatory pathways could be recognised by disease suppression mechanisms. For this reason, TEs could be targeted for therapeutic applications aiming to prevent TE activity or reduce initial inflammatory pathways as well as to activate disease suppression mechanisms. In this review, we describe the contributory and potential preventative roles of TEs in neurological conditions and cancer from a molecular and evolutionary perspective. Evolutionary paradigms both at the unicellular and organismal level aid understanding the role of TEs in disease. These observations could pave the way for the development of novel therapeutic approaches targeting TEs.

The orbital elactronic structure of Rare Earth Elements (REEs) contains many unpaired electrons which render them capable of storing large amount of magnetic energy in addition to being critical for hitech applications. Geological deposits are their conventional sources, and the current supply chain relies on production from these deposits. However, given their critical roles in the anticipated global energy transition, there is the need to explore other viable sources to supplement current and future supplies chains. REEs occur in coal as accessory minerals and their concentration in coal ash to levels that rival those of geological deposits has been estab;ished by sophisticated analytical chemical methods. Conmventional hydrometallurgical processes rely on acid leaching, using tioxic mineral acids. Meanwhile, organosulfonic acids have pKa values that rival those of conventional minerals acid and can, therefore, be used in hydrometallurgy but their uses in this regard are not well documented in the literature. In this extensive review, we have covered geological sources of REEs exaustively in addition to showing the potential of organosulfonic acids as environmentally benign lixiviants for REEs extraction from coal ash. We have also shown how process optimization can be achieved using advance technologies while using organisulfonic acids. Moreover, we have shown current and future global market trends regarding the production of select organosulfonic acids, and the anticipated global increase in their production motivates the use of organosulfonic acids as viable lixiviants for REEs extraction from caol ash deposits.

Three octahedral iron(III) nitrate complexes with dimethylated urea ligand isomers, [hexakis(N,N’-dimethylurea-O)iron(III)] nitrate (compound 1), trans-[diaquatetrakis(N,N-dimethylurea-O)iron(III)] nitrate (compound 2) and [hexakis(N,N-dimethylurea-O)iron(III)] nitrate trihydrate (compound 3) were prepared and characterized with single crystal X-ray diffraction, IR, Raman and UV-VIS methods. In compounds 1 and 3, six dimethylurea ligands coordinate to the central FeIII ion via the oxygen in octahedral geometry and the ligands are arranged in a propeller-like manner, dividing the complex cations into two sides. In compound 1, the dimethylurea propellers screw in the opposite direction on the two sides of the complex and in compound 3, they are arranged with the same handedness on the two sides. The complexes have helical chirality. The two sides of the complex cations differ not only in the rotation direction of the ligands but also in the hydrogen bond formation. On one side of the complex cation, the ligands form intermolecular hydrogen bonds only with the crystal waters, meanwhile on the other side of the complex, the ligands form hydrogen bonds only with the nitrate ions. In compound 2, [Fe(N,N-dimethylurea)4(H2O)2]3+ cations form layers that are separated by interconnected NO3- ions forming a hydrogen bonding system and connecting the complex cations A-s and B-s. The three crystallographically different nitrate ions each form four hydrogen bonds in a way that they have one bidentate O atom and two monodentate O atoms, however, the anions differ in their hydrogen bonding. The spectroscopic characteristics of compound 2 were determined by IR measurements on the deuterated compound 2 as well.

Genes coding for enzymes of the denitrification pathway appear randomly distributed among isolates of the ancestral genus Thermus, but only in few strains of the species T. thermophilus the pathway has been studied to a certain detail. Here, we review the enzymes involved in this pathway present in T. thermophilus NAR1, a strain extensively employed as a model for nitrate respiration, on the light of its full sequence recently assembled through a combination of PacBio and Illumina technologies in order to counteract the systematic errors introduced by the former technique. The genome of this strain is divided in four replicons, a chromosome of 2,021,843 pb, two megaplasmids of 370,865 and 77,135 bp and a small plasmid of 9,799 pb. Nitrate respiration is encoded in the largest megaplasmid, pTTHNP4, within a region that includes operons for O2 and nitrate sensory systems, a nitrate reductase, nitrate and nitrite transporters and a nitrate specific NADH dehydrogenase, in addition to multiple insertion sequences (IS), suggesting its mobility-prone nature. Despite nitrite is the final product of nitrate respiration in this strain, the megaplasmid encodes two putative nitrite reductases of the cd1 and Cu-containing types, apparently inactivated by IS. No nitric oxide reductase genes have been found within this region, although the NorR sensory gene, needed for its expression, is found near the inactive nitrite respiration system. These data clearly support that partial denitrification in this strain is the consequence of recent deletions and IS insertions in genes involved in nitrite respiration. Based on these data, the capability of this strain to transfer or acquire denitrification clusters by horizontal gene transfer is discussed.

It is argued that all physical knowledge ultimately stems from observation and that the simplest possible observation is that an event has happened at a certain space-time location . Considering historic experiments, which had been groundbreaking in the evolution of our modern ideas of matter on the atomic, nuclear and elementary particle scales, it is shown that such experiments produce as outputs macroscopically observable events which represent binary decisions with regard to simple alternatives and which accumulate in the course of time into spatio-temporal patterns whose forms allow decisions to be taken concerning conceivable alternatives of explanation. Working towards elucidating the physical and information-theoretic characteristics of those elementary pieces of information we arrive at the conclusion that - unlike the events of relativity which are mere 4-tuples of spacetime coordinates - the events of observation are pieces of information endowed with the properties of physical action, spacetime extension, and Lorentz invariance. Another important aspect is that such events are produced at the expense of irreversibly dissipating energy which can be stated in Landauer diction in the form that more energy needs to be spent in the erasure of events than had previously been invested in their initiation.

We introduce a new generalized inverse (i.e., generalized EP element) which is a natural generalization of EP and *-DMP elements in a Banach *-algebra. We present polar-like characterizations of generalized EP elements. The necessary and sufficient conditions under which the sum of two generalized EP elements is a generalized EP element are investigated. Finally, the generalized core-EP orders for generalized EP elements are characterized.

The study aimed to evaluate for the first time the degree of contamination of soil and crops with major and trace elements (Cd, Co, Cr, Cu, Ni, Pb, Zn, F, Na, Mg, Si, P, Cl, Fe, Al) in agricultural lands situated in the Lower Danube Basin, Galati and Braila counties (SE Romania), impacted by the steel industry. Soil samples from two depths (0–5 cm and 5–30 cm), as well as leaves and seeds of wheat, corn, and sunflower, were collected from 11 different sites. Along with elemental and mineralogical analysis, performed by HR-CS AAS, PIGE, SEM-EDX and ATR-FTIR, the soil pH, texture, organic matter, electric conductivity and CaCO3 content were investigated. The results showed that the levels of Cr (83.270–383.100 mg kg-1), Cu (17.110–68.151 mg kg-1), Ni (30.157–55.656 mg kg-1), and F (319–544 mg kg-1) in soil exceeded the Romanian regulations for sensitive use of the land. The pollution indices (Igeo, EF, PI, PERI) indicate that the soil is moderate to highly contaminated with Cr, Ni and Cu, while CSI and mERMQ indices suggested a relatively low risk for metal contamination. The concentrations of elements in plant tissues and bioaccumulation factors (BFs) show the soil-plant relation and health risk, but also the elemental selectivity of vegetal compartments. Thus, the results showed that wheat plants tend to exclude the bioaccumulation of certain elements in their tissues, while for Zn and Cu, the bioaccumulation pattern is different. In the case of corn, most BFs were below 1, indicating limited phytoaccumulation capacity. However, exceptions were observed for Cd, Zn, and Cu. Sunflower BFs indicate higher bioconcentration of Cu, Cd, and Zn in both the leaves and seeds compared to other elements. Chromium (Cr) contributes to non-carcinogenic dermal contact and ingestion hazards, with children being more susceptible to the adverse effects of this contaminant.

Smart materials represent an elegant class of (macro)-molecules endowed with the ability to react to chemical/physical changes in the environment. Herein, we prepared new photo responsive azobenzenes possessing halogen bond donor groups. The X-ray structures of two molecules highlight supramolecular organizations governed by unusual noncovalent bonds. In azo dye I-azo-NO2, the nitro group is engaged in orthogonal H···O···I halogen and hydrogen bonding, linking the units in parallel undulating chains. As far as compound I-azo-NH-MMA is concerned, a non-centrosymmetric pattern is formed due to a very rare I···π interaction involving the alkene group supplemented by hydrogen bonds. The Cambridge Structural Database contains only four structures showing the same I···CH₂=C contact. For all compounds, an ¹⁹F NMR spectroscopic analysis confirms the formation of halogen bonds in solution through a recognition process with chloride anion, and the reversible photo-responsiveness is demonstrated upon exposing a solution to UV light irradiation. Finally, the intermediate I-azo-NH2 also shows a pronounced color change due to pH variation. These azobenzenes are thereby attractive building blocks to design future multi-stimuli responsive materials for highly functional devices.

Azobenzene photoswitches are fundamental components in contemporary approaches aimed at light-driven control of intelligent materials. Significant endeavors are directed towards enhancing the light-triggered reactivity of azobenzenes for such applications and obtaining water-soluble molecules able to act as crosslinkers in a hydrogel. Here, we report the rational design and the synthesis of azobenzene/alginate photoresponsive hydrogels endowed with fast reversible sol-gel transition. We started with the synthesis of three cationic azobenzenes (AZO A, B, and C) and then incorporated them in sodium alginate (SA) to obtain photoresponsive supramolecular hydrogels (SMHGs). The photoresponsive properties of the azobenzenes were investigated by UV-Vis and ¹H NMR spectroscopy. Upon irradiation with 365 nm UV light, the azobenzenes demonstrated efficient trans-to-cis isomerization, with complete isomerization occurring within seconds. The return to the trans form took several hours, with AZO C exhibiting the fastest return, possibly due to higher trans isomer stability. In the photoresponsive SMHGs, the minimum gelation concentration (MGC) of azobenzenes was determined for different compositions, indicating that small amounts of azobenzenes could induce gel formation, particularly in 5 wt% SA. Upon exposure to 365 nm UV light, the SMHGs exhibited reversible gel-sol transitions, underscoring their photoresponsive nature. This research offers valuable insights into the synthesis and photoresponsive properties of cationic, water-soluble azobenzenes, as well as their potential application in the development of photoresponsive hydrogels.

Temperature-responsive separation membranes can significantly change their permeability and separation properties in response to changes in their surrounding temperature, improving efficiency and reducing membrane costs. This study focuses on the modification of commercial polyvinylidene fluoride (PVDF) membranes with amphiphilic temperature-responsive copolymer and inorganic nanoparticles. We prepared an amphiphilic temperature-responsive copolymer which the hydrophilic poly(N-isopropyl acrylamide) (PNIPAAm) was side-linked to a hydrophobic polyvinylidene fluoride (PVDF) skeleton. Subsequently, PVDF-g-NIPAAm polymer and graphene oxide (GO) blended with PVDF to prepare temperature-responsive separation membranes. The results showed that temperature-responsive polymers with different NIPAAm grafting ratios were successfully prepared by adjusting the material ratio of PVDF to NIPAAm. PVDF-g-NIPAAm was blended with PVDF with different grafting ratios to obtain separate membranes with different temperature responses. GO and PVDF-g-NIPAAm formed a relatively stable hydrogen bond network, which improved the internal structure and mechanical properties of the membrane without affecting the temperature response, thus extending the service life of the membrane.

Bovine lactoferrin (bLf) is a milk-derived protein that exhibits multiple biological activities and has been explored towards different therapeutic applications. Since this molecule is susceptible to degradation and some of its properties depend on its tertiary structure, the encapsulation of bLf in stimuli-responsive therapeutic formulations provides an added value to potentiate its biological activities when administered. Plasmonic magnetoliposomes emerge as promising nanosystems for dual hyperthermia (magneto-photothermia) and local therapy, since the combination of magnetic and gold nanoparticles (NPs) in a single nanosystem (multifunctional liposomes) enables the targeting and controlled release of encapsulated drugs. In this work, plasmonic magnetoliposomes (PMLs) containing manganese ferrite nanoparticles (28 nm size) and gold nanoparticles (~ 5 nm size) functionalized with 11-mercaptoundecanoic acid or octadecanethiol, were synthesized and loaded with bLf. The structural, magnetic and optical properties of the nanoparticles were measured by TEM, SQUID and UV/vis/NIR absorption spectroscopy. Specific Absorption Rate was determined to assess the capabilities for magnetic and photothermal hyperthermia. Finally, Saccharomyces cerevisiae was used as an eukaryotic cellular model to assess the biological activity and the mechanism of entry of bLf-loaded PMLs, through counting of colony forming units and fluorescence microscopy, respectively. The results demonstrate that PMLs are mainly internalized through an energy- and temperature-dependent endocytic process, though the contribution of a diffusion component cannot be discarded. Most notably, only bLf-loaded PMLs exhibit cytotoxicity with an efficiency similar to free bLf, attesting their promising potential for bLf delivery in the context of therapeutic interventions.

Galdieria maxima is a polyextremophilic alga capable of diverse metabolic processes. Ammonia is widely used in culture media typical of laboratory growth. Recent reports that this species can grow on wastes promote the concept that G. maxima might have biotechnological utility. Accordingly, there is a need to know the range of pH levels that can support G. maxima growth in a given nitrogen source. Here, we examined the combined effect of pH and nitrate/ammonium source on the growth and long-term response of the photochemical process to a pH gradient in different G. maxima strains. All were able to use differing nitrogen sources, despite both the growth rate and photochemical activity were significantly affected by the combination with the pH. All strains acidified the NH4+-medium (pH<3); only G. maxima IPPAS P507 showed reduced capacity in lowering the pH from 6.5. pH was a limiting factor in nitrate uptake at pH≥6.5; noteworthy, at pH 5 on nitrate G. maxima ACUF551 showed a good growth performance, despite the alkalization of the medium.

This study describes the seasonal course of denitrifying and nitrate reducing bacteria in a dimictic mesotrophic lake (Lake Scharmützelsee, Brandenburg, Germany) within a three-year period from 2011 to 2013. The bacterial cell numbers were quantified by fluorescence microscopy, most probable number (MPN) and PCR dependent quantification of the chromosomal 16S rDNA and of the nirS and nirK gene copy number. The highest seasonal differences (up to three orders of magnitudes) has been measured by MPN in the epilimnion. This variation was not reflected by PCR dependent approaches or direct microscopical enumeration. At adverse conditions (low temperature and/or low nitrate concentrations), the differences between MPN and gene copy numbers increased up to five orders of magnitudes and decreased to one magnitude at favorable environmental conditions. These results can be explained best by an increasing ratio of viable but not cultivable (VBNC) cells or dead cells at impairing conditions. In the hypolimnion, the courses of MPN and nir gene copy numbers were similar. This can be explained by higher feeding pressure and therefore smaller amounts of dormant cells. In the pelagial in general, the total cell numbers enumerated by either microscopical or molecular approaches were similar. In the sediment, more than 99 % of the DNA was obviously not related to viable bacteria but was rather “dead DNA” in dead cells or adsorbed to particle surfaces.

Herein, we investigated hydrogels composed of boronic Acid functionalized alginate and blended with polyvinyl alcohol of different molecular weights to control the release of metoclopramide hydrochloride (MTC) as a function of pH and shear stress. The functionalization of alginate introduced dynamic covalent bonding and pH-responsive properties that can modulate network connectivity. The study investigated the viscoelastic properties of the hydrogels, their drug release profiles, and their responsiveness to changes in pH and shear forces. The results showed higher PVA molecular weight and alkaline pH conditions increased hydrogel viscosity and stiffness due to a more stable and interconnected network structure than acidic pH. Metoclopramide release revealed that the hydrogels exhibited pH-responsive drug release behavior. The drug was more readily released under acidic conditions due to the instability of sp2-hybridized boronate ester bonds. The influence of shear forces on the release of metoclopramide was also investigated at shear rates of 1, 10, and 100 s-1, revealing their effect on matrix stiffening. The research shows that AlgBA/PVA hydrogels have unique properties, such as dynamic covalent bonding, that make them sensitive to external mechanical forces. This sensitivity makes them ideal for applications where physiological conditions trigger drug release

Diatomite (DME) consists of natural ordered porous structures that are excellent candidates as microcontainers. However, to the best of our knowledge, the application of DME loaded with corrosion inhibitors in anti-corrosion coatings has not hitherto been reported. In this study, DME has been used as a source of microcontainers to load benzotriazole (BTA) inhibitor by an immersion method. In order to prevent unwanted early release of the small molecule BTA inhibitor from the DME microcontainers, inspired by the adhesion characteristics of catechol and amine in mussel adhesion protein, polydopamine (PDA) was coated on their surfaces to generate BTA@DME/PDA microcapsules. Because of the depolymerization characteristics of PDA at low pH, the synthesize microcapsules showed a controllable release function. The SEM morphology, chemical structure, and loading capacity of the synthesized BTA@DME/PDA microcapsules were characterized. The corrosion resistances of epoxy coatings with different contents of BTA@DME/PDA microcapsules were compared by saline immersion and electrochemical impedance tests. A scratched coating with 5wt.% BTA@DME/PDA microcapsules showed the best anti-corrosion effect.

Drought and salinity are among the most important abiotic stress factors that limit the productivity in economically important plants. Although genes from wild relatives or unadapted germplasm have often been used for stress tolerance breeding, only few studies have examined wild relatives to understand the genetic and molecular basis of stress tolerance. In this study, we monitored the changes in gene expression profiles of leaf and root tissues of two wild barleys (Hordeum spontaneum L.) accessions from Israel after treatment with salt (NaCl) and drought (PEG) stress. We identified a total of 641 differentially expressed genes across 24 conditions (2 accessions, 2 stress conditions, 2 tissues and 3 time points). Our gene expression analyses revealed large numbers of differentially expressed genes in different accessions by different stress treatments. In addition, the number of genes altered in the leaves of stress-exposed plants of both genotypes was higher than those altered in the roots. Interestingly, there was a relatively little overlap between the leaf and the root stress-responsive gene expression patterns, suggesting that different stress-associated processes might be operating in these tissues during stress adaptation. Overall, our results revealed a number of candidate genes and plant processes associated with stress tolerance in wild barley. Wild barley would be a useful source of new genetic variation for drought and salt stress tolerance. Our results could provide new insights into the mechanisms of drought and salt stress tolerance in wild barley and should be useful for genetic improvement of salt-drought tolerance in cultivated barley.

The long-term impact of treatment of dogs with steroid-responsive enteropathy (SRE) on the fe-cal microbiome and metabolome has not been investigated. Therefore, this study aimed to evaluate the fecal microbiome and metabolome of dogs with SRE before, during, and following treatment with standard immunosuppressive therapy and an elimination diet. We retrospec-tively selected samples from 9 dogs with SRE enrolled in a previous clinical trial, which received treatment for 8 weeks, and had achieved remission as indicated by the post-treatment clinical scores. Long-term (1 year) samples were obtained from a subset (5/9) of dogs. Samples from 13 healthy dogs were included as controls (HC). We evaluated the microbiome using 16S rRNA sequencing and qPCR. To evaluate the recovery of gut function, we measured fecal metabolites using an untargeted approach. While improvement was observed for some bacterial taxa after 8 weeks of treatment, several bacterial taxa remained significantly different from HC. Seven-ty-five metabolites were altered in dogs with SRE, including increased fecal amino acids and vitamins, suggesting malabsorption as a component of SRE. One year after treatment, however, all bacterial species evaluated by qPCR and 16S rRNA gene sequencing, and all but thirteen me-tabolites were no longer different from healthy controls.

Alfalfa, an important legume forage, is an ideal crop for sustainable agriculture and a potential bioenergy plant. Drought, one of the most common environmental stresses, substantially affects plants’ growth, development and productivity. MicroRNAs (miRNAs) are newly discovered gene expression regulators that have been linked to several plant stress responses. To elucidate the role of miRNAs in drought stress regulation of alfalfa, a high-throughput sequencing approach was used to analyze 12 small RNA libraries comprising of 4 samples, each with 3 biological replicates. We identified 348 known miRNAs, belonging to 80 miRNA families, from the 12 libraries and 281 novel miRNAs using Mireap software. 18 known miRNAs in roots and 12 known miRNAs in leaves were screened out as drought-responsive miRNAs. Except for miR319d and miR157a which were upregulated under drought stress, the expression pattern of drought-responsive miRNAs were different between roots and leaves in alfalfa. This is the first study discovering miR157a, miR1507, miR3512, miR3630, miR5213, miR5294, miR5368 and miR6173 are drought-responsive miRNAs. Target transcripts of drought-responsive miRNAs were computationally predicted. All 447 target genes for the known miRNAs were predicted using an online tool. This study provides a significant insight on understanding drought-responsive mechanisms of alfalfa.

The authors have revised the circularity of materials, which is important to stimulate circular activity processes. The theoretical part starts with describing the characteristics of the circular activity and the comparison of circular and linear systems in terms of recycling. Later on, the authors examined key elements important for the circularity and the results of an examination of various sectors. The authors formed a correlation matrix and used a dynamic regression model to identify the circular material use rate. The authors suggested a three-level methodology, using it provided a dynamic regression model which could be applied for forecasting the size of circular material use rate in European Union countries. The results show that private investments into recycling and the recycling of electronic waste and the recycling of other municipal waste categories are important in seeking to increase the usage rate of circular materials.

Online social networking techniques and large-scale multimedia retrieval are developing rapidly, which not only has brought great convenience to our daily life, but generated, collected, and stored large-scale multimedia data as well. This trend has put forward higher requirements and greater challenges on massive multimedia retrieval. In this paper, we investigate the problem of image similarity measurement, which is one of the key problems of multimedia retrieval. Firstly, the definition of similarity measurement of images and the related notions are proposed. Then, an efficient similarity measurement framework is proposed. Besides, we present a novel basic method of similarity measurement named SMIN. To improve the performance of similarity measurement, we carefully design a novel indexing structure called SMI Temp Index (SMII for short). Moreover, we establish an index of potential similar visual words off-line to solve to problem that the index cannot be reused. Experimental evaluations on two real image datasets demonstrate that the proposed approach outperforms state-of-the-arts.

Using structured light to drive colloidal motors, due to its advantages of remote manipulation, energy tunability, programmability, and controllability of spatiotemporal distribution, has been attracting much attention in the fields of targeted drug delivery, environmental control, chemical agent detection, and smart device design. Here, we focus on studying the group control of colloidal made from a photo-responsive organic polymer molecule NO-COP (N,O-Covalent organic polymer). These colloidal motors mainly respond to the light intensity patterns. We chose a digital micromirror device (DMD) to modulate the structured light field shining on the sample, by considering its merit of fast refreshing speed, good programmability, and high-power threshold. It is found that under ultraviolet or green light modulation, such colloidal motors exhibit various group behaviors including group diffusion, group patterning, and group migration. The qualitative interpretation is also provided for these observations.

In hospitals and smart nursing homes, ambient-intelligent care rooms are equipped with many sensors. They can monitor environmental and body parameters, and detect wearable devices of patients and nurses. Hence, they continuously produce data streams. This offers the opportunity to collect, integrate and interpret this data in a context-aware manner, with a focus on reactivity and autonomy. However, doing this in real-time on huge data streams is a challenging task. In this context, cascading reasoning is an emerging research approach that exploits the trade-off between reasoning complexity and data velocity by constructing a processing hierarchy of reasoners. Therefore, a cascading reasoning framework is proposed in this paper. A generic architecture is presented allowing to create a pipeline of reasoning components hosted locally, in the edge of the network, and in the cloud. The architecture is implemented on a pervasive health use case, where medically diagnosed patients are constantly monitored, and alarming situations can be detected and reacted upon in a context-aware manner. A performance evaluation shows that the total system latency is mostly lower than 5 seconds, allowing for responsive intervention by a nurse in alarming situations. Using the evaluation results, the benefits of cascading reasoning for healthcare are analyzed.

Spherical microparticles of TiO₂ were synthesized by the ionic liquid-assisted solvothermal method at different reaction time (3, 6, 12 and 24h). The properties of the prepared photocatalysts were investigated by means of UV-vis diffuse-reflectance spectroscopy (DRS), BET surface area measurements, scanning electron microscopy (SEM), X-ray diffraction analysis (XRD), and X-ray photoelectron spectroscopy (XPS). The results indicated that the efficiency of phenol degradation was related with a time of the solvothermal synthesis as determined for TiO₂_EAN(1:1)_24h sample. Microparticles of TiO₂_EAN(1:1)_3h formed during the only 3h of synthesis time revealed really high photoactivity under visible irradiation – 75%. This value increased to 80% and 82% after 12h and 24h, respectively. The photoactivity increase was accompanied by the increase of the specific surface area thus pores size, as well as ability to absorb UV-vis irradiation. The high efficiency of phenol degradation of IL-TiO₂ photocatalysts was ascribed to the interaction between the surface of TiO₂ and ionic liquid components (carbon and nitrogen).

Currently, there is increasing industrial demand for rare earth elements (REE) as these elements are now integral to the manufacture of many carbon-neutral technologies. The depleting REE ores and increasing mining costs are prompting to look for alternative sources for these valuable metals, particularly from waste streams. Although REE concentrations in most of the alternate resources are lower than current REE ores, some sources such as marine sediments, coal ash, and industrial wastes like red mud are looking promising with significant concentrations of REE in them. This review focuses on the alternative resources for REE such as ocean bottom sediments, continental shelf sediments, river sediments, stream sediments, lake sediments, phosphorites deposits, industrial waste products like red mud, and phosphogypsum, coal, coal fly ash, and related materials, waste rock sources from old and closed mines, acid mine drainage, and recycling of e-waste. Possible future Moon exploration and mining for REE and other valuable minerals are also discussed. It is evident that REE extractions from both primary and secondary ores alone are not adequate to meet the current demand, and sustainable REE recovery from the alternative resources described here is also necessary to meet the growing REE demand. An attempt is made to identify the potential of these alternative resources and sustainability challenges, benefits, and possible environmental hazards to meet the growing challenges in meeting the future REE requirements.

Façade elements are a building component that satisfies multiple performance parameters. Among other things, “advanced façades” take advantage of hybrid solutions, such as assembling laminated materials. In addition to the enhanced mechanical properties that are typical of optimally composed hybrid structural components, these systems are energy-efficient, durable, and offer lighting comfort and optimal thermal performance, an example of which is the structural solution developed in collaboration with the University of Zagreb and the University of Ljubljana within the Croatian Science Foundation VETROLIGNUM project. The design concept involves the mechanical interaction of timber and glass load-bearing members without sealing or bonding the glass-to-timber surfaces. Following earlier research efforts devoted to the structural analysis and optimization of thus-assembled hybrid Cross-Laminated Timber (CLT)-glass façade elements, in this paper, special focus is given to a thermal and energy performance investigation under ordinary operational conditions. A simplified numerical model representative of a full-size building is first presented by taking advantage of continuous ambient records from a Live-Lab mock-up facility in Zagreb. Afterwards, a more detailed Finite Element (FE) numerical analysis is carried out at the component level to further explore the potential of CLT–glass façade elements. The collected numerical results show that CLT–glass composite panels can offer stable and promising thermal performance for façades similar to national and European standard requirements.

The extensive use of rare earth elements (REEs) in a number of technologies is expected to impact on human health, including occupational REE exposures. A body of experimental evidence on REE-associated toxicity has been accumulated in recent decades. Unlike experimental studies, the consequences of REE exposures to human health have been subjected to relatively fewer investigations. Geographical studies have been conducted on residents in the Chinese REE mining districts, reporting on REE bioaccumulation, and associations between REE residential exposures and adverse health effects. A more limited series of studies has been focused on occupational REE exposures, such as movie operator (with occurrence of cerium aerosol) with the observation of pneumoconiosis and lung fibrosis. Similar effects have been reported in case reports for other workers, such as a lens grinder and a printer exposed to carbon-arc lamp emission. As for the occupations related to REE mining and processing, REE bioaccumulation in scalp hair and excess REE urine levels were reported. A study was devoted to workers employed in e-waste separation, showing alterations of several plasma markers. As for other REE occupational exposures, mention should be made of: a) mechanical workshops, with exposures to diesel exhaust microparticulate (containing nanoCeO₂ as a catalytic additive) and, b) production and manufacture of REE supermagnets for hybrid engines and wind turbines. Diesel exhaust microparticulate has been studied in animal models, leading to evidence of several pathological effects in animals exposed by respiratory or systemic routes. As for supermagnet production and manufacture, a body of literature is reviewed of experimental studies, and of human exposure studies showing several pathological effects of static magnetic fields, warranting further investigations.

Bone fractures are very common in the geriatric population and poses a great economic burden worldwide. While traditional methods for repairing bone defects have primarily been autografts, there are several drawbacks limiting its use. Bone graft substitutes have been used as alternative strategies to improve bone healing. However, there remains several impediments to achieving the desired healing outcomes. Injectable hydrogels have become attractive scaffold materials for bone regeneration given their high performance in filling irregularly sized bone defects, ability to encapsulate cells and bioactive molecules, and mimic the native ECM of bone. We investigated the use of an injectable chitosan-based hydrogel scaffold to promote differentiation of preosteoblasts in vitro. The hydrogels were characterized by evaluating cell homogeneity, cell viability, rheological and mechanical properties, and differentiation ability of preosteoblasts in hydrogel scaffolds. Cell-laden hydrogel scaffolds exhibited shear thinning behavior and the ability to maintain shape fidelity after injection. The CNC-CS hydrogels exhibited higher mechanical strength and significantly upregulated the osteogenic activity and differentiation of preosteoblasts as shown by ALP activity assays and histological analysis of hydrogel scaffolds. These results suggest that this injectable hydrogel is suitable for cell survival, can promote osteogenic differentiation of preosteoblasts, and structurally support new bone growth.

The paradigm of drug delivery via nano- and microcarriers is one of the leading ideas that enable overcoming the limitations of traditional chemotherapy. The trend toward more complex drug carriers capable of multifunctionality is observed in the literature. To date, prospects of stimuli-responsive systems to control the cargo release in the lesion nidus are widely accepted. Both endogenous and exogenous stimuli are employed for this purpose, however, endogenous pH is one of the most common triggers. Unfortunately, scientists face difficulties in the implementation of this idea since a range of biological barriers, drug bioavailability issues, and challenges in the synthesis of carriers with required properties have arisen. Here, we discuss fundamental strategies of pH-responsive drug delivery as well as limits in its application and reveal the main problems, weak sides, and reasons for poor clinical results. Also, we have made an attempt to formulate the profiles of "ideal" drug carrier in the frame of different strategies and considered recently published studies through the lens of these profiles. This approach enables the identification of current trends and promising vectors in the development of pH-responsive drug delivery systems, as well as challenges to be resolved in the next generation of carriers.

Gaseous air pollutants emitted from anthropogenic sources are diverse and form secondary products through photochemical reactions, complicating the regulatory analysis of anthropogenic emissions in the atmosphere. Here, we used an environmental chassis dynamometer and a photochemical smog chamber to conduct a parameter sensitivity experiment to investigate the formation of secondary products from a direct-injection gasoline passenger car. To simulate the mitigation of ammonia (NH3) emissions from gasoline vehicle exhausts assuming future emission controls and to allow photochemical oxidation and aging of the vehicle exhaust, NH3 was selectively removed by a series of five denuders installed between the vehicle and the photochemical smog chamber. Overall, there were no differences in the formation of secondary organic aerosols and ozone with or without NH3 mitigation. However, the secondary particle formation potential of ammonium nitrate (NH4NO3) was significantly reduced with NH3 mitigation. In addition, NH3 mitigation resulted in increased particle phase acidity due to HNO3 in the gas phase not being neutralized by NH3 and condensing onto the liquid particle phase, indicating a potentially important secondary effect associated with NH3 mitigation. The present study provides new insights into the effects of NH3 mitigation on secondary emissions from gasoline vehicle exhaust and the experimental approach.

The theory of one-photon ionization and two-photon above-threshold ionization is formulated for applications to heavy atoms in attosecond science using the Dirac-Fock formalism. A direct comparison of the Wigner-Smith-Eisenbud delays for photoionization is made with delays from the Reconstruction of Attosecond Beating By Interference of Two-photon Transitions (RABBIT) method. Photoionization by an attosecond pulse train, consisting of monochromatic fields in the extreme ultraviolet range, is computed with many-body effects at the level of the Relativistic Random Phase Approximation (RRPA). Subsequent absorption and emission processes of infrared laser photons in RABBIT are evaluated using static ionic potentials as well as asymptotic properties of relativistic Coulomb functions. As expected, light elements, such as Argon, show negligible relativistic effects, while heavier elements, such a Krypton and Xenon, exhibit delays that depend on the fine-structure of the ionic target. The relativistic effects are notable close to ionization thresholds and Cooper minima with differences in fine-structure delays predicted to be as large as tens of attoseconds. The separability of relativistic RABBIT delays into a Wigner-Smith-Eisenbud delay and a universal continuum--continuum delay is studied with reasonable separability found for photoelectrons emitted along the laser polarization axis in agreement with prior non-relativistic results.

3D printing facilitates the straightforward construction of microchannels with complex three-dimensional architectures. Here, we demonstrate 3D-printed modular mixing components that operate on the basis of splitting and recombining fluid streams to decrease interstream diffusion length. These are compared to helical mixers that operate on the principle of chaotic advection.

Plants have a natural protective process of altering their genetic molecules in response to changing environments. To uncover the genetic potential of plants, it is crucial to understand how they adapt to adverse conditions by analyzing their genetic molecules. In the study, we focused on understanding the responsive genes of tomatoes under drought conditions. We analyzed RNASeq data from different Tomato genotypes, tissue types, and different drought durations. We used a time series scale to identify early and late drought-responsive gene modules and applied a machine learning method to identify the best responsive genes. We found six candidate genes of Tomato (ASCT, FLA2, BAG5, DCL2b, NFP7.3, and ADC1) that were responsive to drought. We further constructed their protein-protein interaction network to identify their potential interactors and found them drought responsive proteins. The candidate genes can help to explore the adaptation of tomato plants under drought conditions. The identification of these candidate genes and modules can have far-reaching implications for molecular breeding and genome editing in Tomato, providing insights into the molecular mechanisms that underlie drought adaptation. This research underscores the importance of the genetic basis of plant adaptation, particularly in changing climates and growing populations.

The disruption of conventional manufacturing, supply, and distribution channels for medical supplies during the COVID-19 pandemic has caused widespread shortages and catalyzed local efforts to use nontraditional, rapid manufacturing to meet urgent healthcare needs. Here we present a crisis-responsive design framework designed to assist with product development under pandemic conditions. The framework utilizes extensive stakeholder engagement, comprehensive and dynamic needs assessment, local manufacturing, and product testing for the accelerated development of healthcare products. We contrast this framework with traditional medical device manufacturing and discuss relevant regulatory policies. We highlight the applicability of the crisis-responsive framework to a successful local program that designed and supplied face shields for a large US academic hospital. Finally, we make recommendations aimed at improving future resilience to healthcare emergencies. These include continued development of open source designs suitable for rapid manufacturing and changes in regulatory policy that strike a balance between rigidity and uncontrolled innovation.