The state detection of power cable is very important to ensure the reliability of power supply. Traditional sensors are mostly based on electric field detection, the operation is complex, and its efficiency needs to be improved. This paper optimizes the design and development of the magnetic field detection sensor for AC power cables. Firstly, through the establishment of the magnetic field sensor model, it is determined that permalloy is the material of the magnetic core, the optimal aspect ratio of the magnetic core is 20, and the ratio of coil length to core length is 0.3. Secondly, the coil simulation model is established, and it is determined that the optimal number of turns of the coil is 11000 turns, the diameter of the enamelled copper wire is 0.08mm, and the equivalent magnetic field noise of the sensor is 0.06pT. Finally, the amplifying circuit based on negative magnetic flux feedback is designed and the sensor is assembled, and the experimental circuit is built for sensitivity test. the results show that the sensitivity of the magnetic field sensor is 327.6mV/μT. The sensor designed in this paper has the advantages of small size, high sensitivity, easy to carry and high reliability.

The magnetic properties of 0.10 mm ultra-thin grain-oriented (UTGO) silicon steel and Fe-based amorphous (FBA) alloy under sinusoidal excitation were measured experimentally, and the magnetic field strength and iron loss of the two materials under different frequencies and magnetic densities were obtained. Based on the measured data, the magnetization and loss characteristics of the two materials were analyzed and compared. Furthermore, two Epstein square ring models of the same specification and different materials were designed, and the reliability of the models was verified. Then, the electromagnetic characteristics of the two Epstein square ring models at higher and lower frequencies were calculated by using the finite element method, and the iron loss was obtained and compared. The results show that the FBA alloy has good application characteristics at low frequency and low power, and the 0.10 mm UTGO silicon steel has good application characteristics at high frequency and high power. This research can provide important data basis to promote the application of these two materials in new energy equipment.

To accomplish IMO's emissions reduction targets, the Chinese government has established emission control areas and implemented strict sulfur limitation policies. Faced with the downturn in the shipping industry and the challenge of insufficient supply of compliant fuel, Hong Kong and Shenzhen in China have implemented different low-sulfur fuel subsidy policies. Therefore, it is particularly important to study the air pollution control mechanism considering low sulfur fuel subsidy policy. Firstly, the non-cooperative game models considering low-sulfur fuel subsidies are constructed. Secondly, the mechanisms of various factors affecting port pricing, throughput and profit are analyzed. Then, a case study is conducted by using AIS data of container ships in Shanghai Port and Ningbo Zhoushan Port. The study reveals that whether the container service price of the leader port increases or decreases, the follower port always take corresponding follow-up measures. In both sequential and simultaneous game, the profit difference of the leader port is positively related to the subsidy ratio of the port’s own and negatively related to the coefficient of the competitor's subsidy. In conclusion, the low-sulfur fuel subsidy policy has a significant positive impact on the step-by-step implementation of more stringent pollution reduction policies in port waters.

This research proposes a methodology for minimizing losses in transmission lines (LT), considering the reconfiguration of the architecture of the electrical power system (SEP). The implementation of this methodology redirects the power flow with optimal switching through its LTs to guarantee the stability of the voltage, angle, frequency, and power balance to minimize losses that affect the reliability and quality of the system. Optimal transmission switching (OTS) allows various types of analysis to be carried out, where the loadability of the lines, response times, and operating costs, among others, can be improved. This article proposes to minimize the losses in the transmission lines with the OTS by using AC power flows as a mixed integer nonlinear problem (MINLP). Several test scenarios evaluate the method’s effectiveness, determining the optimal topology for corrective control that optimizes power flows in different situations. It has been proven that this approach reduces losses compared to a base case by 99%, even in the face of N-1 or random contingencies, without losing load, maintaining the same active power dispatch, and finally verifying a strategic increase in dispatch of reactive power to maintain operating parameters within stable limits.

Under the development mode of deep blending of emerging technologies, major projects are important for enhancing China's comprehensive national strength and independent innovation capability. Based on the social benefits of major projects, and considering the influence of reputation factors, an evolutionary game model composed of a general contractor and subcontractor of major projects is established. This paper studies the influence of various factors including the income distribution coefficient of collaborative innovation, and MATLAB simulation software is analyzed the influence of factors on an evolutionary path. The results show that a reasonable income distribution coefficient can promote the game behavior of both parties to the direction of active collaborative innovation; The reduction of innovation cost and the improvement of spillover technology absorption capacity can make innovation subjects tend to choose active collaborative innovation strategies. In addition, reputation loss above a specific threshold can effectively inhibit free-riding behavior and encourage innovation subjects to choose active collaborative innovation strategies. The research results provide reference for promoting major projects' technology innovation.

Cooperative localization under complex urban environments has become a solution to replace the Global Navigation Satellite System (GNSS) positioning. Due to utilizing distance measured and information exchanged between vehicles, cooperative localization results in high computational complexity and heavy communication overhead. This paper proposes a cooperative localization method based on evolutionary coalitional game theory, which implements vehicles' location estimation with less communication cost. We select the neighboring vehicles to form a coalition based on the node's square position error bound and communication cost. The location is obtained via exchanging information between vehicles. It is evident from the simulations and results that the proposed method holds low communication overhead while maintaining localization accuracy.

This paper describes the proposal and development of a proof of concept (PoC) for a data logger system designed for operation and fault detection in bench testing of combustion engines. The main objective was to develop a data logger system that collects data on vibration, sound, temperature, and CO2 levels to identify ignition and combustion faults, thereby contributing to reducing greenhouse gas emissions (GHG). The paper presents (i) the proposal and development and (ii) the open-source code: proof of concept for a data logger system focused on detecting faults and monitoring the operational condition of benchtop combustion engines. The results indicate the feasibility of the PoC for data acquisition and dataset creation for Research and Development purposes.

Transportation plays an important role in urban development. Population growth and environmental burden have turned the efforts of cities globally towards smarter and greener mobility. Cooperative and Connected Automated Mobility (CCAM) serves as a concept with the power and potential to help achieve these goals building upon technological fields like Internet of Things, computer vision and distributed computing. However, its implementation is hindered by various challenges covering technical parameters such as performance and reliability in tandem with other issues, such as safety, accountability and trust. To overcome these issues, new distributed and decentralized approaches like blockchain and smart contracts are needed. This paper aims at identifying a comprehensive inventory of CCAM challenges and use it as a framework to describe methodologies using blockchain and smart contracts to address them. It provides a comparative analysis of the findings to draw useful conclusions and discuss future directions in CCAM and relevant blockchain applications. The paper contributes to intelligent transportation systems’ research by offering an integrated view of the difficulties in substantiating CCAM and providing insights on the most prominent blockchain and smart contract technologies that tackle them.

Intelligent transportation systems (ITS) are at the forefront of advancements in transportation, offering enhanced efficiency, safety, and environmental friendliness. To enable ITS, autonomous systems play a pivotal role, leveraging breakthroughs in autonomous driving, data-driven modeling, and multiagent control strategies to establish sustainable and coordinated traffic management. The integration of connected and automated vehicles has garnered significant attention as a potential solution for alleviating traffic congestion and improving fuel economy, achieved through global route optimization and cooperative driving. This study focuses on a predictive control perspective to address the cooperative cruise control problem. Online decision-making is employed during the driving process, utilizing information gathered from the network. By employing bargaining games to establish an operating agreement among vehicles, we formalize a synchronization approach based on predictive control theory. Ultimately, these findings are put to the test in an emulation environment within a hardware-in-the-loop system.

UAV cooperative control has been an important issue in UAV-assisted sensor network, thanks to the considerable benefit obtained from cooperative mechanism of UAVs being applied as a flying base station. In coverage scenario, the tradeoff between coverage performance and transmission performance often makes deployment of UAVs fall into a dilemma, since both indexes are related to the distance between UAVs. To address this issue, UAV coverage and data transmission mechanism is analyzed in this paper, then an efficient multi-UAV cooperative deployment model is proposed. The problem is also modeled as a coalition formation game (CFG). The CFG with Pareto order is proved to have a stable partition. Then, an effective approach consisting of coverage deployment and coalition selection is designed, wherein UAVs can decide strategies cooperatively to achieve better coverage performance. Combining analysis of game approach, a coalition selection and position deployment algorithm based on Pareto order (CSPDA-PO) is designed to execute coverage deployment and coalition selection. Finally, simulation results are shown to validate the proposed approach based on efficient multi-UAV cooperative deployment model.

Recognizing the need to enhance immune cells' ability to target and eliminate tumor cells by focusing on tumor-associated antigens is crucial for the success of immunotherapy. Numerous cell-based therapies, such as CAR-T cell therapy, tumor-infiltrating lymphocyte (TIL) therapy, CAR-NK cell therapy, and T-cell receptor (TCR)-based therapies, are currently undergoing clinical and pre-clinical evaluation across various cancer types. However, a significant challenge lies in managing the inflammatory responses that are harmful to cancer patients. To overcome this, developing advanced strategies to target tumor cells precisely while preserving immune balance in cancer patients is imperative. One promising approach involves using modified tumor-associated macrophages (TAMs), which constitute approximately 50% of the tumor microenvironment (TME) and play a pivotal role in tumor progression. CAR-Macrophage (CAR-M) therapy is an emerging potential asset of immunotherapy for a wide range of tumors.

The upgrade of energy infrastructure to those of smart grids, necessarily goes through the provision of integrated technological solutions that ensure the interoperability of their business capabilities and reduce the risk of devaluation of the systems used. The heterogeneity of the infrastructures and the dynamics of their operating environment, requires the continuous reduction of the complexity, the faster execution of the processes and the easy addition of innovative counterparts. Also, the integrated management of the overall ecosystem demands the provision of end-to-end interconnection, quality assurance, the definition of strict security policies, collaborative integration and correlation of events. In this respect, every design detail can be critical to the success or failure of a costly and ambitious project, such as that of smart energy networks. This work presents communication operating standards specific to the smart electricity networks applications, which should be taken into account in the process of planning and implementation of new infrastructures.

The rapid integration of Information and Communication Technology (ICT) is transforming the traditional electrical grid into a {\em Smart Grid}. Smart grids enable two-way communication and improved monitoring and control between utilities and customers. However, due to its heterogeneous nature, public exposure, and weak security at low-powered devices, the Smart Grid has vulnerabilities to various malicious threats, adversaries, and cyber attacks, which may affect cost and service availability. Additionally, when the systems' confidentiality, integrity, or availability are compromised, the resulting fallout can threaten national security and have cascading effects on human lives. Given the extreme consequences of an attack, smart-grid technology must be thoroughly tested for correct operation and security {\em before} it is deployed. As a result, vulnerability testing of smart grids, not only for correctness but for security purposes, has been the subject of numerous studies by academics, government agencies, and private companies. This paper reviews the vulnerabilities associated with the smart grid and spotlights simulation as the vulnerability testing methodology conducted in recent pertinent research works. It also presents various security aspects of the smart grid, including grid applications, system and network infrastructure and components, cyber threats and attacks, simulation, and different mitigation techniques. Finally, we analyze the gaps in the current research works, focusing on simulation. We briefly present a real-time simulation testbed that mimics customer behaviour and integrates hardware in the loop to apply attack methods, analyze vulnerabilities and risk mitigation associated with the smart grid system, and propose future work to improve the current framework.

This paper proposes an innovative approach to address the challenge of softening deformation of thermal-curable thermosets during additive manufacturing. This approach involves the development of a composite powder composed of thermosetting materials with distinct curing temperatures, the utilization of Cold Spray Additive Manufacturing (CSAM) technology for 3D printing, and the application of a stepwise isothermal curing process. The corresponding effectiveness is validated by case studies. The results demonstrate that samples printed via CSAM maintain a solid state without deformation. During the post-curing process, each component of the composite material cures independently while the other components remain in a solid state, providing structural support for the whole material, thereby effectively reducing the softening deformation during the post-curing process. This approach offers a novel perspective for the additive manufacturing of thermal-curable thermosets.

We model the financial markets as a game and make predictions using Markov chains estimators. We extract the possible patterns displayed by the financial markets, define a game where one of the players is the speculator, whose strategies depend on his/hers risk-to-reward preferences, and the market is the other player, whose strategies are the previously observed patterns. Then we estimate the market’s mixed probabilities by defining Markov chains and utilizing its transitions matrices. Afterwards, we use these probabilities to determine which is the optimal strategy for the speculator. Finally, we apply these models to real-time market data to determine its feasibility. After all, we obtained a model for the financial markets that has an outstanding performance in terms of accuracy and profitability.

This article provides a detailed analysis of non-invasive techniques for prediction and diagnosis of faults in internal combustion engines, focusing on the application of the Proknow-C and Methodi Ordinatio systematic review methods. Initially, the relevance of these techniques in promoting energy sustainability and mitigating greenhouse gas emissions is discussed, aligning with the Sustainable Development Goals (SDGs) of Agenda 2030 and the Paris Agreement. The systematic review conducted in the subsequent sections offers a comprehensive mapping of the state-of-the-art, highlighting the effectiveness of combining these methods in categorizing and systematizing relevant scientific literature. The results reveal significant advancements in the use of artificial intelligence (AI) and digital signal processors (DSP) to enhance fault diagnosis, as well as underscore the crucial role of non-invasive techniques in minimizing interference in monitored systems. Finally, concluding remarks point towards future research directions, emphasizing the need to develop digital twins for internal combustion engines and identify gaps for further improvements in fault diagnosis and prediction techniques.

We applied evolutionary game theory to extend a resource constrained security game model for confidentiality attacks in an Advanced Metering Infrastructure (AMI), which is a component of IoT-enabled Smart Grids. The AMI is modelled as a tree structure where each node aggregates the information of its children before encrypting it and passing it on to its parent. As a part of the model, we developed a discretization scheme for solving the replicator equations. The aim of this work is to explore the space of possible behaviours of attackers and to develop a framework where the AMI nodes adaptively select the most profitable strategies. Using this model, we simulated the evolution of a population of attackers and defenders on various cases resembling the real life implementation of AMI. We discuss in depth how to enhance security in AMI using evolutionary game theory either by a priori analysis or as a tool to run dynamic and adaptive infrastructure defence.

This study highlighted the core and critical tenets that constitute culturally responsive science assessments (CRSciA) for K-12 education and aligned them with the capabilities of generative AI (GenAI). The tenets were identified based on their dominance in the literature, including Indigenous Language, Race and Ethnicity, Religious Beliefs, Family and Community, and Indigenous Knowledge. These tenets were instrumental in developing the GenAI-CRSciA framework and the subsequent prompts to generate CRSciAs aligned with the Next Generation Science Standards (NGSS) while comparing it with standard prompt strategies. The results showed that the GenAI-CRSciA prompting approach outperformed normal prompting strategies in terms of generating CRSciAs, proving its effectiveness in addressing the ongoing challenges in science assessments. Even though the GenAI-CRSciA framework presented assessments that cover a range of the cultural backgrounds, it presents potential challenges such as compromising curricula core competencies and overgeneralization of students’ backgrounds; overlooking subcultural variations within a country or region, for example differences between urban and rural students, or between different ethnic or linguistic groups within the same nation, which can lead to bias and less effective CRSciA outputs. To address this, we recommend that teachers provide comprehensive and specific background information about their students when using the GenAI-CRSciA prompting, ensuring that the generated content is truly reflective of the students’ unique cultural contexts. In larger class settings, teachers could implement comprehensive local data indexing, where detailed student background information is uploaded and retrievable for use in crafting more personalized CRSciAs. We strongly recommend educators to make conscious efforts to validate the generated assessments with input from human experts, including community or family, educators, and even students who are knowledgeable about the cultural nuances. We also suggest continuous professional development would be necessary to enhance teachers’ understanding of the cultural tenets.

The success of deep learning (DL) in offline brain-computer interfaces (BCIs) has not yet translated into efficient online applications. This is due to three primary challenges. First, most DL solutions are designed for offline decoding, making the transition to online decoding complex and unclear. Second, the use of sliding windows in online decoding increases the computational complexity of DL training. Third, DL models typically require large amounts of training data, which are often scarce in BCI applications. To address these issues and enable real-time decoding, even across different subjects without calibration data, we first introduce a novel approach called real-time adaptive pooling (RAP). RAP modifies the pooling layers of existing offline DL models towards the online decoding requirements. Additionally, it significantly reduces the computational demand during training by jointly decoding consecutive windows. To reduce the amount of training data required, our approach leverages different levels of domain adaptation. We show how different settings enable different adaptation solutions. The results demonstrate that our approach is both powerful and can be calibration-free, providing a robust and practical solution for real-time BCI applications. These findings pave the way for the development of co-adaptive and highly efficient DL-based online BCI systems.

Non-invasive continuous health monitoring has become feasible with the advancement of biosensors. While monitoring certain biomarkers such as heart rate or skin temperature are now at certain maturity, monitoring molecular biomarkers is still challenging. Progress has been shown in sampling, measurement and interpretation of data towards non-invasive molecular sensors that can be integrated in daily wearable items. Towards this goal, this paper explores the potential of embroidered interdigitated transducer (IDT)-based sensors for non-invasive, continuous monitoring of human biomarkers, particularly glucose levels, in human sweat. The study employs innovative embroidery techniques to create flexible fabric-based sensors with gold-coated IDTs. In controlled experiments, we have shown the variation of glucose concentration in water can be wirelessly detected by tracking the resonant frequency of the embroidered sensors. The current sensors operate at 1.8GHz–2GHz and respond to the change of glucose concentration with a sensitivity of 0.17 MHz/(mg/dl). The embroidered IDT-based sensors with wireless sensing will be a new measurement modality for molecular wearable sensors. The establishment of a wireless sensing mechanism for embroidered IDT-based sensors will be followed by investigation of sweat for molecular detection. This will require adding functionalities for sampling and interpretation of acquired data. We envisage the embroidered IDT-based sensors offer a unique approach for seamless integration into clothing, paving the way for personalised, continuous health data capture.

The smart grid system, an improvised form of the traditional grid, is considered a critical cyber-physical system. Due to its complex combination of smart and legacy technologies, this technology is characterized by a wide range of features such as full duplex communication, advanced metering infrastructure, remote monitoring, and control. However, despite this system’s substantial environmental and socio-economic impact on modern life, it poses severe security vulnerabilities due to its integration and interconnected and interdependent cyber-physical components. Based on the rapid development of cyber-physical systems (CPS), academics and industries have investigated relevant techniques to enhance and strengthen the security measures of the SG system. The intrusion detection system is a countermeasure, a powerful safeguard against various cyber-attacks and threats. The contribution of the IDSs to the SG paradigm is examined in this study. A comprehensive review has been presented in this study, highlighting different techniques, basic ideas, and analyses. Besides discussing the contemporary pertinent research studies, the shortcomings of the existing IDS for the SG system are also identified with a recommendation for future research direction.

In South Korea, in line with the increasing need for a reliable water supply following the continuous increase in water demand, the Smart Water Grid Research Group (SWGRG) was officially launched in 2012. With the vision of providing water welfare at a national level, SWGRG incorporated information and communications technology in its water resource management, aiming at the development of core technologies for a Smart Water Grid consisting of intelligent microgrids and a demonstration and tests of the developed technologies through a field operation in a living lab. The living lab was built in Block 112 of YeongJong Island, Incheon, South Korea (area of 17.4 km2, population of 8,000), where Incheon International Airport, a hub of Northeast Asia, is located. In this location, water is supplied through a single submarine pipeline, making the place optimal for responses to water crises and the construction of a water supply system during emergencies. From 2017 to 2019, ultrasonic wave type smart water meters and IEEE 802.15.4g advanced metering infrastructure (AMI) networks were installed at 527 sites of 958 consumer areas in the living lab, and core element technologies (intelligent water source management and distribution system, smart water distribution network planning/control/operation strategy establishment, AMI network and device development, integrated management of bi-directional smart water information), and operation solutions (smart water statistics information, real-time demand-supply analysis, decision support system, real-time hydraulic pipeline network analysis, smart DB management, and water information mobile application) were developed through a field operation and testing.

Frontal Polymerization (FP) is recognized as a polymer synthesis method capable of generating a highly localized and self-propagating exothermic front, considered a more rapid and energy-efficient manufacturing scheme for polymer-based fiber-reinforced composite materials. This study conducts a numerical investigation based on the Finite Element Method into the initiation and propagation of frontal polymerization of acrylamide. Utilizing Differential Scanning Calorimetry (DSC) experiments, the study phenomenologically tests the curing kinetics reactions of acrylamide (AM) in deep eutectic solvent (DES)-based polymerizable systems, thereby establishing a curing kinetics model for the autocatalytic reaction of polyacrylamide. By coupling the heat conduction diffusion equation of the frontal polymerization reaction, the Finite Element Method is employed to solve the reaction-diffusion model, aiming to explore the evolution of temperature and degree of curing during the manufacturing process. The results demonstrate the reliability and accuracy of the nth-order autocatalytic model in the study of curing kinetics for DES-based synthesis, indicating that the front propagation speed of the AM-based FP reaction is influenced by the activation temperature, duration of activation temperature, and initial temperature of the solution. Experimental validation of the polyacrylamide manufacturing through frontal polymerization corroborates the accuracy and reliability of the model predictions, providing a reference for the numerical model study and temperature control in the synthesis of acrylamide composite hydrogels via FP.

This article presents a buck converter in which the inductor has been replaced by a transmission line. This approach would be practically conceivable if the power supply and load have a greater spatial distance. In the time domain, this new converter can be described by a system of coupled partial and ordinary differential equations. In the frequency domain, a transcendental transfer function is obtained. For comparison with an equivalently parameterized conventional converter, Padé approximants are derived. A linear controller is designed for the converter topology under consideration.

Emerging data processing techniques brought back into attention the HF range communication as an interesting alternative to third-party solutions for IoT applications, such as data transmission in distributed energy production facilities. The physical size of HF antennas, often comparable to the surrounding objects, require in-situ radiation measurements. Drone-borne measuring systems are already known as a flexible solution, but mostly restricted to higher frequency ranges. In this work, we propose to use an electrically small, folded dipole as a probe for drone-borne measurements on HF antennas. We also propose a calibration approach for the effects related to the near-field zone, and to the drone body proximity. The impact of ground reflection is also investigated. We show that despite its low, realized gain figure such a probe can provide stable results for near-field measurements, even at low input power levels.

We present the mathematical model of cooperative functioning of unconscious and consciousness. The model is based on the theory of open quantum systems. Unconscious and consciousness are treated as bio-information systems. The latter plays the role a measurement apparatus for the former. States of both systems are represented in Hilbert spaces. Consciousness performs measurements on the states which are generated in unconscious. This process of unconscious-conscious interaction is described by the scheme of indirect measurements. This scheme is widely used in quantum information theory and it leads to the theory of quantum instruments (Davis-Lewis-Ozawa). Our approach is known as quantum-like modeling. It should be sharply distinguished from modeling of genuine quantum physical processes in biosystems, in particular, in the brain. In the quantum-like framework, the brain is a black box processing information in the accordance with the laws of quantum theory. During the last 10-15 years this framework has been actively used in cognition, psychology, decision making, social and political sciences. The quantum-like scheme of unconscious-consciousness functioning has already been explored for sensation-perception modeling.

The European Green Deal poses a two-pronged challenge for the automotive industry: migrating to solutions based in light structures, requiring light weight concepts and light materials, while at the same time avoiding dependence towards the importation of these advanced materials. Aluminium alloys are lightweight and cost-effective materials that can successfully cover the requirements of many structural applications, however their production requires from bauxite and other Critical Raw Materials (CRM), such as Si and Mg. Aluminium alloys are fully recyclable, but scrap is usually contaminated and its use is related to an increment of impurities, tramp element and undesired inclusions. Traditionally, the use of secondary alloys has been restricted to low performance applications. The present work analyses the effect that the use of scrap has in the quantity of inclusions present in the alloy and in other properties relevant for the material processing. The study was carried out for common alloys belonging to 3 of the most common aluminium processes used in the car manufacturing industry: High Pressure Die Casting (HPDC) (EN AC-43500), extrusion (6063) and sheet metal forming (5754 and 6181). Reference alloy were mixed with different level of scrap (0, 20, 40, 60, 80 and 100%) trying to keep the chemical composition as unaffected as possible. The inclusions level of the alloy was characterized with the Prefil Foot-printer® test. In addition, the obtained materials, after being cast in an open mould, were subjected to metallographic characterization. Relevant properties to assess the formability quality of the alloys for the corresponding transforming process, were obtained: flowability test for HPDC alloy and high temperature compression for extrusion alloys. The results obtained suggest that the number of inclusions present in the melt highly increase with the amount of scrap used to produce the alloy. These inclusions are also related with an important lost of flowability, but do not have a noticeable impact on microstructure.

While the role of safe riding behavior as a safety contributor for cyclists has been increasingly studied in recent years, there have been few studies analysing cycling behavior in relation to crash-related outcomes in Baltic countries. Indeed, to the best of our knowledge, this is the first time this issue has been addressed in the case of Latvia. Aim: The objective of this study was to assess the relationships among self-repotted cyclists’ behavior, traffic safety literacy, and their cycling crash involvement rates. Method: A total of 299 cyclists aged M=32.8 from across Latvia (42% females) participated in an online survey, which comprised questions regarding respondents’ demographics, frequency of riding, and the number of crashes in the past five years. The Cycling Behavior Questionnaire (CBQ) and the Cyclist Risk Perception and Regulation Scale (RPRS) were applied to assess cyclists' behavior patterns and traffic safety literacy. Results: According to the findings, it can be inferred that cyclists frequently engage in riding errors and traffic violations while cycling. Those who exhibit more antisocial behavior patterns are also more likely to be involved in road crashes. Conversely, cyclists with greater positive behavior rates more often also tend to possess better knowledge of traffic rules and exhibit a heightened risk perception, indicating a greater awareness of road traffic safety. Conclusion: All in sum, this study underscores key age differences, with older individuals significantly less involved in riding crashes, exhibiting fewer driving errors and a higher level of risk perception, which serves as a crucial factor in road safety. At the practical level, these results stress the need to address both traffic safety literacy and protective cycling factors of cyclists, in a manner to improve overall road safety and promote active transport modes in Latvia.

In the context of constructing new power systems, distribution networks are increasingly incorporating distributed resources such as distributed photovoltaic (PV) systems, decentralized wind turbines (WT), and new types of energy storage system (ESS), which may lead to prominent issues such as voltage overruns and reverse heavy overloads in the distribution network. While distributed resources are valuable for voltage regulation, their regulation characteristics vary with their operation means, and the randomness and volatility of renewable power generation will also influence the optimization and regulation of voltage in the distribution network. This paper proposes a multi-time scale reactive power optimization and regulation method for distribution networks in a multi-source interactive environment. Firstly, the voltage regulation characteristics of distributed PV systems, decentralized ES, and distributed WT are analyzed. Based on this analysis, then a multi-time scale voltage optimization scheme for distribution networks using MPC method is proposed, which optimizes the voltage regulation strategies for each distributed resource in a rolling manner. Furthermore, an event-triggered real-time voltage zoning control strategy based on voltage sensitivity is proposed to address the real-time sudden voltage overlimit problems. The modified IEEE 33-node system is used to verify the performance of proposed method, simulation results indicate that the issue of voltage overruns at distribution network nodes has been improved, and the intraday rolling optimization yields results that are more realistic compared to the day-ahead optimization method.

Smart grids are seeing an increase in renewable energy and an enormous introduction of advanced power electronics, increasing the number of disturbance sources. This requires improving the accuracy of measurement systems capable of acquiring data for use in power system monitoring applications. Rogowski Coils (RCs) and Merging Units (MUs) are being widely deployed in controlling, metering, and monitoring of digital power systems. Because the performance of digital measurement devices has a direct influence on power measurement accuracy, it is critical to perform a laboratory calibration of these measurement instruments before they are installed in any project. To determine the magnitude and phase displacement errors of the RC+MU under normal and abnormal operating conditions, this article presents a comprehensive laboratory digital calibration system constructed from precise, readily available commercial products such as a fluxgate current transducer and a National Instrument. In addition, the analysis of measurement chain is affected by sources of uncertainty is discussed. The tests yield findings that are consistent with the relevant standards.

Presently power control and management play a vigorous role in information technology and power management. Instead of non-renewable power manufacturing, renewable power manufacturing is preferred by every organization for controlling resource consumption, price reduction and efficient power management. Smart grid efficiently satisfies these requirements with the integration of machine learning algorithms. Machine learning algorithms are used in a smart grid for power requirement prediction, power distribution, failure identification etc. The proposed Random Forest-based smart grid system classifies the power grid into different zones like high and low power utilization. The power zones are divided into number of sub-zones and map to random forest branches. The sub-zone and branch mapping process used to identify the quantity of power utilized and the non-utilized in a zone. The non-utilized power quantity and location of power availabilities are identified and distributed the required quantity of power to the requester in a minimal response time and price. The priority power scheduling algorithm collect request from consumer and send the request to producer based on priority. The producer analysed the requester existing power utilization quantity and availability of power for scheduling the power distribution to the requester based on priority. The proposed Random Forest based sustainability and price optimization technique in smart grid experimental results are compared to existing machine learning techniques like SVM, KNN and NB. The proposed random forest-based identification technique identifies the exact location of the power availability, which takes minimal processing time and quick responses to the requestor. Additionally, the smart meter based smart grid technique identifies the faults in short time duration than the conventional energy management technique is also proven in the experimental results.

The volatility and uncertainty associated with the high proportion of wind and PV output in the new power system significantly impact power and energy balance, making it challenging to accurately assess the risks related to renewable energy abandonment and supply guarante. Therefore, a probabilistic power and energy balance risk analysis method based on distributed robust optimization is proposed. Firstly, the affine factor and the flexible ramp reserve capacity of thermal power are combined to establish a probabilistic index, which serves to characterize the risk associated with power and energy balance. Drawing upon the principles of conditional value at risk theory, the risk indexes of load shedding power and curtailment power under a certain confidence probability are proposed. Secondly, the probability distribution fuzzy sets of uncertain variables are constructed using the distributionally robust method to measure the Wasserstein distance between different probability distributions. Finally, aiming at minimizing the operation cost of thermal power, the risk cost of power abandonment and the risk cost of load shedding, a distributed robust optimal scheduling model based on flexible ramp reserve of thermal power is established.

The forest is a complex and dynamic ecosystem that requires integrated planning and management, considering economic, social, environmental, and ecological dimensions. Different stakeholders often have conflicting goals, making optimal management decisions challenging. This study aims to balance increasing economic benefits for forest users with reducing negative environmental impacts, aligning the interests of managers, government institutions, and policymakers. To achieve this, multi-objective optimization methods and game theory were used. The objectives were to maximize the net present value of wood harvesting and the amount of carbon sequestration. The study was conducted in the Shafarood forest in northern Iran. Data collected included stumpage prices, variable harvesting costs, tree density per ha, volume per ha, growth rates, interest rates, carbon sequestration, and labor costs. Using this data, models were developed for the expected mean price of various species, stored carbon, logistics growth, and labor. After adjusting the objective functions and model constraints, the range of Pareto optimal solutions for the multi-objective model and the Nash equilibrium for the game theory model were determined using the epsilon-constrain method. The results indicate that both modeling approaches can identify optimal points for balancing economic and environmental goals. The Pareto optimal range and Nash equilibrium allow for informed decision-making in managing the Hyrcanian forests, accommodating different user goals. Therefore, both models are effective tools for forest management planning and provide a framework for achieving sustainable management practices.

The lack of defect image data is one of the main factors affecting the accuracy of supervised deep learning-based defect detection models. In response to the insufficient training data of defect images with complex backgrounds such as rust and surface oil leakage in substation equipment, leading to poor performance of the detection model, this paper proposed a novel adversarial deep learning model for substation defect generation: ADD-GAN. In comparison to existing generative adversarial networks, this model generates defect images based on effectively segmented local areas of substation equipment images, avoiding image distortion caused by global style changes. Additionally, the model utilizes a joint discriminator for overall image and defect image to address the issue of low attention to local defect areas, thereby improving the loss of image features. This enhances the overall quality of generated images as well as locally generated defect images, ultimately improving image realism. Experimental results demonstrate that the YOLOV7 object detection model trained on the dataset generated using the ADD-GAN method achieves an mAP of 81.5% on the test dataset, representing an improvement of 9.6% over the original dataset, 5.7% over traditional augmentation methods, and 7% over typical adversarial deep learning methods. This confirms that the ADD-GAN method can generate a high-fidelity dataset of substation equipment defects.

The state-of-the-art smart city has been calling for an economic but efficient energy management over large-scale network, especially for the electric power system. It is a critical issue to monitor, analyze and control electric loads of all users in system. In this paper, we employ the popular computer vision techniques of AI to design a non-intrusive load monitoring method for smart electric energy management. First of all, we utilize both signal transforms (including wavelet transform and discrete Fourier transform) and Gramian Angular Field (GAF) methods to map one-dimensional current signals onto two-dimensional color feature images. Second, we propose to recognize all electric loads from color feature images using a deep neural network with multi-scale feature extraction and attention mechanism. Third, we design our method as a cloud-based, non-intrusive monitoring of all users, thereby saving energy cost during electric power system control. Experimental results on both public and our private datasets have demonstrated our method achieves superior performances than its peers, and thus supports efficient energy management over large-scale Internet of Things.

Starting from a very simple economic scenario, we build on it a game and then we introduce a general strategy able to reduce a regression problem to an equivalent binary classification problem. This reduction scheme (that we call adaptive reduction or also dynamic reduction) can be also used to derive a new boosting algorithm for regression problems named bOOst^d. The bOOst^d algorithm is very simple to implement, and it can use any learning algorithm with no priori assumptions. We present a conjecture for bOOst^d performances, which ensures a little error on training set. More important we can also provide a very good theoretical upper bound for the generalization error. We give a set of preliminary experimental results that seems to confirm our conjecture for bOOst^d performances on training set and the theoretical assumptions for the generalization error. We also provide a possible justification of why boosting often does not overfit. Finally, we leave some open problems and argue that in the future an adaptive single boosting (with an unique code) algorithm for binary, multi class and regression problems can be derived.

As the adoption of renewable energy sources grows, ensuring a stable power balance across various time frames has become a central challenge for modern power systems. In line with the "dual carbon" objectives and the seamless integration of renewable energy sources, harnessing the advantages of various energy storage resources and coordinating the operation of long-term and short-term storage have become pivotal directions for future energy storage deployment. To address the complexities arising from the coupling of different time scales in optimizing energy storage capacity, this paper proposes a method for energy storage planning that accounts for power imbalance risks across multiple time scales. Initially, the Seasonal and Trend decomposition using the Loess (STL) decomposition method is utilized to temporally decouple actual operational data. Subsequently, power balance computations are performed based on the obtained data at various time scales to optimize the allocation of different types of energy storage capacities and assess the associated imbalance risks. Finally, the effectiveness of the proposed approach is validated through hourly applications using real-world data from a province in China over recent years.

While the beneficial effects of using magnetic and electromagnetic treatment (ET) of brackish and saline waters on soil salinity reduction in the root zone were widely reported more studies are needed to answer questions about the soil salt leaching efficiency and the effect of the duration of the exposure to ET. For this aim, pot experiments were conducted using an Aqua-4DR physical water treatment device. The first experiment included two trials. The first considered 5 concentrations: C0:1.0; C1:4.5; C2:9; C3:13.5; and C4:18 dSm-1. The results revealed that the volume and the salt concentrations of the drained waters were significantly higher under irrigation with ET saline waters than those provided by untreated waters. The drained fraction of water varied from 20 to 26% under irrigation with untreated water and increased from 33 to 56% under irrigation with electromagnetized water indicating an improvement of salt leaching. The second trial was carried out with different irrigation doses. The result showed that the higher the dose, the more obvious and significant ET effect. The different treatment durations of water exposure revealed that the volume and salinity of drained water significantly increase as the ET duration increases. An increase in ET duration induces also an increase in soil water content of around 2.5%. Based on the experimental findings, we may conclude that the ET of saline water can reduce the adverse effect of salinity on the top soil, but these leached salts are carried away in depth and there is no concentration limit of water to the effect of the ET.

In this paper, a new type of self-excited thermomechanical oscillator containing an oscillating shape memory alloy (SMA) filament with two symmetrically arranged spheres is investigated. The self-excitation of the oscillations is due to a heater of constant temperature, which causes periodic contractions of the filament when it approaches it. The contracted filament moves away from the heater a distance sufficient to cool it. Under the action of the weight of the spheres, the cooled filament re-approaches the heater, causing the above processes to repeat periodically. On the basis of experimental studies, approximating functions of the heater's heat field distribution are derived. A dynamic model of the oscillator has been created, in which the minor and major hysteresis in the SMA alloy and the distribution of the heat field around the heater have been taken into account. By numerical solutions of the differential equations, the laws of motion of the spheres are obtained. The displacements of the spheres in two perpendicular directions were measured using an experimental system. The obtained experimental results validate the proposed dynamic model and its assumptions with a high degree of confidence. Conclusions are drawn about the stochastic nature of the oscillations due to the hysteresis properties of the SMA and the temperature variation of the natural frequency of the oscillating system.

It is a critical issue to allocate redundancy to critical smart grid infrastructure for disaster recovery planning. In this study, we present a framework to combine statistical prediction methods and optimization models for the optimal redundancy allocation problem. First, we develop statistical simulation methods to identify critical nodes of very large-scale smart grid infrastructure based on the topological features of embedding networks, and then present a linear integer programming model based on generalized assignment problem (GAP) for redundancy allocation of critical nodes in smart grid infrastructure. The model is specifically implemented in the context of smart grid infrastructure. The findings demonstrate that the combined approach of statistical simulation and optimization effectively addresses the size limitations inherent in a sole optimization approach. Notably, the optimal solutions for redundancy allocation in very large grid systems highlight that the cost of redundancy is only a fraction of the economic losses incurred due to weather-related outages.

From ancient time, electric grid system developed as one way direction in which users get the electricity from generators to far end. However, it is not the consumer centric as its one way process and consumer have no way to communicate to the server. Thus, with the development of digital revolution, the grid converted to smart grid and meter converted to smart meter. In smart grid, the protocol follows the bidirectional way of communication with support of consumers in the system. Recently in 2016, Jo et al. proposed the scheme for smart grid system using privacy preserving model and claimed to be efficient and secure. However, in this paper we have analyzed the scheme of Jo et al. and proved that the scheme is vulnerable to Replay attack and afterwards shows the change in protocol to withstand against this attack.

Smart grid software interconnects multiple Engineering disciplines (power systems, communication, software and hardware technology, instrumentation, big data, etc.). The software architecture is an evolving concept in smart grid systems in which systematic architecture development is a challenging process. The architecture has to realize the complex legacy power grid systems and cope up with current Information and Communication Technologies (ICT). The distributed generation in smart grid environment expects the software architecture to be distributed and to enable local control. Smart grid architecture should also be modular, flexible and adaptable to technology upgrades. In this paper, the authors have made a comprehensive review on architecture for smart grids. An in depth analysis of layered and agent based architectures is presented and compared under various domains.

This paper presents an 8x8 channel optoelectronic readout array (ORA) realized in a 180-nm CMOS process for the applications of short-range light detection and ranging (LiDAR) sensors. We propose several circuit techniques in this work including an amplitude-to-voltage (A2V) converter that reduces the notorious walk-errors by intensity compensation, and a time-to-voltage (T2V) converter that acquires the linear slope of the output signals by exploiting a charging circuit, thus extending the input dynamic range significantly from 5 uApp to 1.1 mApp, i.e. 46.8 dB. These results correspond to the maximum detection range of 8.2 meters via the action of the A2V converter and the minimum detection range of 56 centimeters with the aid of the proposed T2V converter. Optical measurements utilizing an 850-nm laser diode confirm that the proposed 8 x 8 ORA with 64 on-chip avalanche photodiodes (APDs) can successfully recover the narrow 5-ns light pulses even at the shortest distance of 56 centimeters. Hence, this work provides a potential CMOS solution for low-cost, low-power short-range LiDAR sensors.

Accurately estimating the pose of spacecraft is indispensable for space applications. However, such targets are generally non-cooperative, i.e., no markers are mounted on it and no parts for operation. Therefore, the detection and measurement of a non-cooperative target is very challenging. Stereovision sensors are important solutions in the near field. In this paper, a rectangular natural feature recognition and pose measurement method for non-cooperative spacecraft is proposed. Solar panels or the bodies of spacecraft are selected as detection objects and their image features are captured by stereo vision. These rectangle features are then reconstructed in 3D Cartesian space through parallelogram fitting on the image planes of two cameras. The vertexes are used to calculate the center position of the rectangle and the direction of the fixed coordinate system to solve the pose and attitude of the non-cooperative target. An experimental system is built to validate the effectiveness of the algorithm. The experimental results show that the average position measurement error of the algorithm is about 10mm and the average attitude measurement error is less than 1°. The results show that the proposed method has high accuracy and efficiency.

In the modern power grid, characterized by the increased penetration of power electronics and extensive utilization of renewable energy, inverters-based power plants play a pivotal role as the principal interface of renewable energy sources (RESs) and the grid. Considering the stability characteristics of grid-following (GFL) inverters when the grid is relatively weak, the application of grid-forming (GFM) controls becomes imperative to enhance the stability of the entire power plant. Thus, there is an urgent need for suitable and effective models to study the interaction and stability of the paralleled inverters employing GFL and GFM controls. Thus, the small-signal modeling with full-order state space model and eigenvalues analysis is presented in this paper. First, the small-signal state-space model of the individual GFL and GFM inverters is obtained considering the control loop, interaction, reference frame, transmissions, and time delays. Then, the models of the individual inverter are extended to the hybrid inverters to study the effects of the GFM inverters on the small- signal stability of the entire system. And, the impacts of the inertia and damping are analyzed by the eigenvalues of the state-transition matrix. Case comprising three parallel GFL inverters and two GFL inverters with one GFM inverter, respectively, are studied to examine the effectiveness and accuracy of the model. Finally, the stability margin obtained from the eigenvalue analysis of the entire system is verified by time-domain simulations.

Promoting close and sustainable cooperation between schools, enterprises, and government has become an important concern in many countries. Based on evolutionary game theory, this paper constructs a tripartite evolutionary game model of schools, enterprises, and government in order to analyze the stability of strategies of the different players. The results show that the main factor that influences the stability of the strategies of schools and enterprises is the reward of positive cooperation from sources other than the government, and the main factor that influences the stability of the strategy of the government is the benefit of positive cooperation strategy under the scenario where schools cooperate with enterprises. Therefore, the government should focus on implementing more effective policies, such as increasing the incentives and penalties, improving the mechanism for managing conflicts, ensuring the fairness of benefits distribution, and clarifying the responsibilities of different departments; schools should focus on providing more practical curricula and programs for students, training high-quality teachers, and perfecting talent cultivation to meet the needs of enterprises; and enterprises should focus on providing job experiences for students and transforming the results of schools’ teaching and theoretical research into practical productivity.

Due to the great threat of torpedo against surface warships, an efficient hydroacoustic countermeasure system must output realtime strategies that can accommodate varied antagonizing scenarios. Aiming at the decision-making problem in the anti-torpedo hydroacoustic countermeasure cases, this paper proposes an intelligent adversarial strategy based on the game theory. By discretizing the strategy space of both sides, a matrix game model is established with the payoff characterized by the capture probability of attacking torpedo. An improved simplex algorithm is then developed to get the mixed-strategy Nash equilibrium of the game model, with which preferred avoiding strategies can be obtained to minimize the risk of being captured by the attacking torpedo. Based on the probabilistic view of preferred adversarial strategy, the launching strategy of floating acoustic decoy can be achieved, and the evasion trajectory of warship can be confirmed simultaneously. Numerical simulation demonstrates that the proposed method can generate realtime intelligent antagonizing strategy, and consequently, can improve the survival rate of surface warships in the of anti-torpedo countermeasure scenarios.

The authors argue that despite significant numbers of foreign workers present in the Russian labor market Russia remains unattractive for highly skilled foreign workers. The economic crisis the country has faced since 2014 has resulted in a further outflow of foreign nationals from OECD countries. So Russia has to look for employees among newcomers from the former Soviet states, the majority of whom come from Central Asia. Russian politics with regard to immigration is characterized by the collision between “geopolitical” and domestic policy rationales. On one hand, seeking to maximize its influence in the post-Soviet space Russia provides preferential conditions of employment for citizens of partner countries in the framework of the Eurasian Economic Union. On the other hand, the Kremlin is afraid to liberalize its approach to immigration and the integration of immigrants through fear of losing popularity among the electorate. The second substantial feature of Russian immigration politics is an extreme level of securitization of migration issues. The government considers these issues primarily through a policing lens. One cannot claim that the Russian state does not take any steps to liberalize “migratory regulation”; however, the effect of these measures is being vastly reduced by new restrictions. In addition, liberally designed laws do not bring the expected results due to the corrupt practices that pervade the whole of migration regulation.

Protection suit is vital for fireman’ safety. Traditional protection suit just physically protects fireman from empyrosis, but can not locate the body injury position from the impact debris. Herein, we present a wearable impact debris positioning system for fireman protection suit alarming based on accelerometer array. The wearable piezoelectric accelerometers with distribute regularly on the suit to detect the vibration on different body parts, which is conducive to positioning injured body parts. In addition, the injured parts can be displayed on the dummy body model on the upper computer with a higher localization accuracy of 4 cm. The positioning alarm system has a rapid response time of 0.11ms attributing to smart signal processing method. This work provides a reliable and smart method for locating and assessing the body injury position from the impact debris, which is significant for fire disaster commander to rescue injured fireman in time.

This paper presents a theory on graph topological structure and graph coloring, proving that for any N-order graph structure (with a topological structure similar to ), the maximum number of colors required for coloring is less than or equal to . The Four Color Theorem is just one special case of this theory, with the maximum structure size for a four-color graph being a 4-order structure graph, hence requiring only a maximum of 4 colors for coloring.

The development and utilization of wind energy is of great significance to the sustainable development of China's economy and the realization of the goal of "dual carbon". Under the typhoon system, the randomness and volatility of wind speed become an important basis for affecting the energy efficiency utilization and design of wind turbines. Therefore, based on wind speed and wind direction data at 10m, 30m, 50m and 70m heights of a wind power tower in Yancheng, Jiangsu Province, this paper analyzes the change characteristics of wind speed and wind direction by using BFAST method and Hurst index. Based on typhoon body data, topographic data and mesoscale system wind direction data, the causes of the occurrence and development of wind speed and wind direction of wind tower are further analyzed, and a conclusion is drawn: (1) In BEAST method, there are 5, 5, 6 and 6 change points at the height of 10m, 30m, 50m and 70m respectively. Among them, the change points at the height of 10m, 30m and 50m all change before and after node 325, and the change time point at the height of 70m is inconsistent with other heights. Hurst index results show that the inconsistency at 70m altitude is stronger than that at other altitudes. (2) The wind direction sequence at 10m, 30m, 50m and 70m altitude is fitted by stages, and the direction of wind direction is SE-E-SE-SW-W-NW, where, At the height of 70m, the deviation of the fitting trend line from other altitudes is larger in the wind speed strengthening stage and weakening stage. (3) The wind speed at the height of 10m and 70m has different response degrees to the typhoon body. The correlation between the wind speed and the distance between the wind measurement tower and the typhoon near the center is stronger at the height of 10m than at the height of 70m. The surface type and the wind direction of the mesoscale system also have certain effects on the wind speed and direction. In this paper, the change characteristics and influencing factors of wind speed and direction of wind tower are studied, which provides methods and theoretical support for the study of short-term wind speed when typhoon passes through, and provides reliable support for the selection of wind power forecast indicators and the selection and design of wind turbines under extreme gale weather systems.

Currently, urban renewal activities in China are booming. And promoting the renovation of public buildings is the key due to its large scale, high cost and significant impact to the nature and social environment. To reduce the ambiguity and uncertainty in evaluating the potential for renewal of existing public buildings, a renewal potential evaluation model combining game theory combination weighting method and cloud model theory is proposed. The paper constructs a comprehensive evaluation index system based on relevant standards and literature. Game theory is used to optimize the weights obtained by AHP and entropy weight methods to obtain a combined weight. MATLAB programming is used to calculate the comprehensive cloud parameters of the evaluation index for the potential renewal of existing public buildings and therefore generate cloud Graphs. Through case study in Nanjing of China, it has been demonstrated that the combination empowerment cloud model can objectively reflect the relationship between the fuzziness and randomness of evaluation indicators for public building renewal potential. The expression of cloud Graphs can intuitively reflect the magnitude of renewal and renovation potential and the degree of uncertainty in evaluation results. The research result provides useful references for the sustainable utilization of building resources in the era of building.

Because of the significant enabling role smart meters can play in securing the transition towards sustainable energy distribution, the paper provides insights to support smart meters implementation projects. Energy utilities must propose adequate solutions to manage grid-upgrading projects and, in the meantime, increase efficiency levels. Based on empirical data analysis the paper provides insights aimed at maximize probability of success of smart meters projects. Results show common patterns of variables that may support project undertakers, policymakers and scholar when it comes to analyze projects to predict to maximize opportunities. For smart meters projects to succeed, regulatory stability is essential as long-period investments grids produce benefits for energy utilities, and for society.

Smart grid capabilities have grown significantly in recent years. The smart grid provides advanced real-time handling of faults, advanced automatic control for efficient electricity transmission, monitoring and collection of the electrical system's capacity, and communication for information sharing. Unfortunately, its exposure to public networks makes it increasingly vulnerable to privacy breaches, vulnerabilities, and cyber-attacks. Cyber security threats and vulnerabilities in smart grid networks have become a primary concern that needs to be addressed before deploying a smart grid. Furthermore, the wide range of protocols increases the attack surface of a smart grid. This study focuses on the vulnerability of Modbus, which is regarded as one of the most prevalent protocols in smart grid communication networks. This paper presents preliminary findings of analyzing cyber-attacks against the Modbus protocol using a virtual testbed to investigate its effects on the smart grid network protocol. The concept incorporates an emulated Modbus/TCP network environment built from open-source software components that imitate fundamental industrial control features of the smart grid. Finally, we analyze the cycle of a cyber-attack leading through Reconnaissance to a DoS attack on the Modbus/TCP protocol and propose improvements to the test bed for protocol attack detection and mitigation.

A cognitive radio sensor network (CRSN) based Smart Grid (SG) is a new paradigm for a modern SG. It is totally different from the traditional power grid and also different from the conventional SG that uses a static resource allocation technique to allocate resources to sensor nodes and communication devices in the SG network. Due to the challenges associated with competitive sensor nodes and communication devices in accessing and utilizing radio resources, the need for dynamic radio resource allocation (RRA) has been proposed as a solution for allocating radio resources to sensor nodes in a CRSN based smart grid ecosystem (network). These challenges include energy/power constraints, poor quality of service (QoS), interference, delay, spectrum efficiency issues, and excessive spectrum hand-offs. Hence, the optimization of resource allocation criteria, such as energy efficiency, throughput maximization, QoS guarantee, fairness, priority, interference mitigation/avoidance, etc., will go a long way in addressing the problems of RRA in a CRSN based SG. Consequently, this work explores RRA in CRSNs for SGs. Various resource allocation schemes, as well as its architecture in a CRSN for SG environment, are presented. The work reported in this paper introduces a model called the “guaranteed network connectivity channel allocation” for throughput maximization (GNC-TM) and optimal spectrum band determination in RRA for improved throughput criteria in CRSNs for SGs. The results show that the model outperforms the existing protocol in terms of throughput and error probability. Finally, the contribution to knowledge and future research direction, such as energy efficiency and hybrid energy harvesting schemes are highlighted.

Cloud computing refers to applications delivered as services over the Internet. Cloud systems employ policies that are inherently dynamic in nature and that depend on temporal conditions defined in terms of external events, such as the measurement of bandwidth, use of hosts, intrusion detection or specific time events. In this paper, we investigate an optimized resource management scheme named v-Mapper. The basic premise of v-Mapper is to exploit application-awareness concepts using software-defined networking (SDN) features. This paper makes three key contributions to the field: (1) We propose a virtual machine (VM) placement scheme that can effectively mitigate the VM placement issues for data-intensive applications; (2) We propose a validation scheme that will ensure that a service is entertained only if there are sufficient resources available for its execution and (3) We present a scheduling policy that aims to eliminate network load constraints. An evaluation was carried out with various benchmarks and demonstrated that v-Mapper shows improved performance over other state-of-the-art approaches in terms of average task completion time, service delay time and bandwidth utilization. Given the growing importance of supporting large-scale data processing and analysis in datacentres, the v-Mapper system has the potential to make a positive impact in improving datacentre performance in the future.

Recently there has been growing interest in the application of game theory (GT) to solve many diverse problems in the field of construction, including i.a.: tender preparation, selection of a contractor for construction works, negotiating terms and conditions of cooperation of the parties to the contract, analysis and modeling of investment risk. In the authors opinion, the use of GT by general contractor (GC) of construction works to indicate the best strategy leading to winning court proceedings in a situation of conflict with investor (IN), so far has not been the subject of research. Taking into account the above, the aim of the presented paper is to indicate the optimal strategy from the GC point of view in the conflict situation with IN. The article presents a list of the most common causes of conflicts between parties of the construction works' contract, defines the background of the problem and the cause of the dispute, and on its basis, the authors generate the theoretical model of the game. Based on the analyzed game model, expected payoffs for players were calculated and the probability border value at which GC should apply the indicated strategy determined. The results of the study show that in the case when the probability of issuing a judgment favorable for GC is at least equal to 69.23%, it is justified to use an aggressive strategy. The analysis also confirms that from the financial perspective, litigation in most cases of conflicts in the area of construction should be the last choice.

Driving factors of smart city construction are exploratively studied by grounded theory method based on text sources from journal papers in SCI and CSSCI databases. Initial scale of driving factors about smart city construction is obtained on the basis of above analyses. This paper modifies measuring items of the initial scale with a small sample pretest and reliability test, then forms final items by exploratory factor analysis. According to the above scale, questionnaires are designed to obtain empirical data, and confirmatory factor analysis is used to verify further validity and reliability of the scale. The results show that driving factors of smart city construction include three main dimensions: problem-oriented factors, business- or technology-driven factors and endogenous development requirements.

This study investigates the long-term stability of the Suomi National Polar-orbiting Partnership (S-NPP) Visible Infrared Imaging Radiometer Suite (VIIRS) moderate-resolution Thermal Emissive Bands (M TEBs; M12 – M16) covering a period from February 2012 to August 2020. It also assesses inter-sensor consistency of the VIIRS M TEBs among three satellites-S-NPP, NOAA-20, and NOAA-21 over eight months spanning from March 18 to November 30, 2023. The field of interesting is limited to the ocean surface between 60°S and 60°N, specifically under clear-sky conditions. Taking radiative transfer modeling (RTM) as the transfer reference, we employed the Community Radiative Transfer Model (CRTM) to simulate VIIRS TEB brightness temperature (BTs), incorporating European Centre for Medium-range Weather Forecasts (ECMWF) reanalysis data as inputs. Our results reveal two key findings. Firstly, the reprocessed S-NPP VIIRS TEBs exhibit a robust long-term stability, as demonstrated through analyses of the observation minus background BT differences (O-B ∆BTs) between VIIRS measurements (O) and CRTM simulations (B). The drifts of the O-B BT differences are consistently less than 0.105 K/Decade across all S-NPP VIIRS M TEB bands. Notably, observations from VIIRS M14 and M16 stand out with drifts well within 0.04 K/Decade, reinforcing their exceptional reliability for climate change studies. Secondly, excellent inter-sensor consistency among these three VIIRS instruments is confirmed through the double-difference analysis method (O-O). This method relies on the O-B BT differences obtained from daily data. The mean inter-VIIRS O-O BT differences remain within 0.08 K for all M TEBs, except for M13. Even in the case of M13, the O-O BT differences between NOAA-21 and NOAA-20/S-NPP have values of 0.312 K and 0.234 K, respectively, which are comparable to the 0.2 K difference between some TEBs among VIIRS and MODIS. These disparities are primarily attributed to the significant differences in the Spectral Response Function (SRF) of NOAA-21 compared to NOAA-20 and S-NPP. Our study confirms the RTM-based TEB quality evaluation method’s versatility and effectiveness in assessing long-term sensor stability and inter-sensor consistency. The double-difference approach effectively mitigates uncertainties and biases inherent to CRTM simulations, establishing itself a robust mechanism for assessing inter-sensor consistency. In addition, we’ve observed that, except for M13, M12 always exhibits larger spatial variations of O-O BT differences with greater uncertainties compared to the other M TEBs. The influence of solar contribution through sea surface reflection on the Top of Atmosphere (TOA) radiance measurements during daytime in M12 should not be underestimated.

In this work, studies were carried out on the extraction of silver and gold from cakes of pressure oxidation leaching of sulfide concentrate containing pyrite and arsenopyrite. The addition of gypsum at a consumption of 0.1 g/g of concentrate helps to increase silver extraction from 13.4 to 95–98% at the cyanidation stage, with no conditioning operation. Gold recovery was 99%. An increase in gypsum consumption contributes to the formation of BFAS with an increased content of sulfate sulfur, and a decrease in the As/S(sulfate) molar ratio in the cake from 3.7 down to 0.88 contributes to an increase in silver extraction at the cyanidation stage up to 98%, and its further decrease from 0.88 down to 0.58 leads to a gradual reducing silver transfer into solution from 98 down to 75.1% at the cyanidation stage. Basic ferric sulfate (BFS) is not formed in this case, since according to EDS mapping the distribution of arsenic and sulfur over iron-containing particles is uniform. According to TCLP analysis, the cake obtained after pressure oxidation leaching with the addition of gypsum and cyanidation is stable and suitable for disposal, since the final concentration of arsenic in the solution was 0.45 mg/dm3.

Vertical Indoor Farming (VIF) with hydroponics offers a promising perspective for sustainable food production. Intelligent control of VIF system components plays a key role in reducing operating costs and increasing crop yields. Modern machine vision (MV) systems use Deep Learning (DL) in combination with camera systems for various tasks in agriculture, such as disease and nutrient deficiency detection, and flower and fruit identification and classification for pollination and harvesting. This study presents the applicability of MV technology with DL modelling to detect the growth stages of chilli plants using YOLOv8 networks. The influence of different bird’s eye and side view datasets and different YOLOv8 architectures was analysed. To generate the image data for training and testing the YOLO models, chilli plants were grown in a hydroponic environment and imaged throughout their life cycle using four camera systems. The growth stages were divided into growing, flowering and fruiting classes. All trained YOLOv8 models showed reliable identification of growth stages with high accuracy. The results indicate that models trained with data from both views show better generalisation. YOLO’s middle architecture achieved the best performance.

The silver fir (Abies alba Mill.) is among the most valuable conifers in Europe for ecological and economic reasons. In the course of history, primarily in the 20th century, its share in stands has been declining due to ill-suited management practices, especially clear-cut management, air pollution, and wildlife-induced damage. Based on recent knowledge of fir ecology and population dynamics, small-scale shelterwood and selection management have been introduced in fir stands, which have also stabilized them. Fir is an essential species for maintaining high stability and biodiversity, especially on planosols and in waterlogged habitats. Due to its shade tolerance and environmental flexibility, particularly at higher altitudes, it can coexist very well with many tree species in mixtures, which can increase the productive potential of stands. It can form stands of heterogeneous structure, ranging from single to multi-layer to selection. For its successful natural regeneration, it is essential to reduce cloven-hoofed game and thus prevent bud browsing damage. On the other hand, fir is a species relatively resistant to bark stripping and the spread of secondary rot compared to Norway spruce (Picea abies [L.] Karst.). During global climate change, fir is expected to shift to higher elevations with sufficient precipitation, while in the southern part of its natural range or at lower elevations, outside water-influenced habitats, it is likely to decline. This paper essentially reviews the description and distribution of the species, its ecological requirements, threats and diseases, habitat and stand conditions, and close-to-nature forest management practices with emphasis on ongoing climate change.

(1) Background: We aim to construct a machine learning (ML) algorithm to predict the risk of distant metastasis (DM) of T1 and T2gallbladder cancer (GBC); (2) Demographic and clinical pathological data of T1 and T2 GBC patients were extracted from the National Institutes of Health (NIH)’s Surveillance, Epidemiology, and End Results (SEER) database between 2004 and 2015 to develop seven ML algorithm models. Models were evaluated based on accuracy, precision, recall rate, F1- score, and area under the receiver operating characteristic curve (AUC); (3) Results:A total of 4371 patients were included in the study, of whom 764 (17.4%) developed DM. Multivariate logistic regression showed that age, histology, tumor size, T and N stages were independent factors in GBC with DM. A novel nomogram was established to predict distant metastasis in early T stage GBC patients. Evaluation indicators of the best model Random Forest (RF) were as follows: accuracy (0.828), recall rate (0.862), precision (0.811), F1- score (0.836), and AUC value (0.913); (4) Con-clusions: The RF model constructed in this study could accurately predict distant metastasis in GBC patients, which may provide clinicians with more personalized clinical decision-making recom-mendations.

In this research article, the notions of SuperHyperDominating and SuperHyperResolving are defined in the setting of neutrosophic SuperHyperGraphs. Some ideas are introduced on both notions of SuperHyperDominating and SuperHyperResolving, simultaneously and as the same with each other. Some neutrosophic SuperHyperClasses are defined based on the notion, SuperHyperResolving. The terms of duality, totality, perfectness, connectedness, and stable, are added to basic framework and initial notions, SuperHyperDominating and SuperHyperResolving but the concentration is on the “perfectness” to figure out what’s going on when for all targeted SuperHyperVertices, there’s only one SuperHyperVertex in the intended set. There are some instances and some clarifications to make sense about what’s happened and what’s done in the starting definitions. The key point is about the minimum sets. There are some questions and some problems to be taken as some avenues to pursue this study and this research. A basic familiarity with SuperHyperGraph theory and neutrosophic SuperHyperGraph theory are proposed.

This study analyzes the eating behavior and factors associated with the presence of disordered eating attitudes in patients undergoing bariatric surgery. It is a cross-sectional, descriptive, and analytical study conducted at a hospital in the Amazon region of Brazil. The Disordered Eating Attitude Scale reduced version (DEAS-s) was used to assess the risk of eating disorders and the Three-Factor Eating Questionnaire (TFEQ-R21) to characterize eating behavior. A total of 205 patients participated, with a mean age of 37.5 ± 8.6 years, the majority being female (93.7%; p<0.001), the mean BMI was 45.3±6.7 kg/m2. It was found that cognitive restraint had the highest mean (52.6±19.9; p<0.001). As for the DEAS-s, the question with the highest mean was "spending one or more days without eating or consuming only liquids to lose weight" (2.80±1.99). Female participants had a higher score in the emotional eating (p=0.016). Disordered eating attitudes showed a correlation with emotional eating and uncontrolled eating. These results suggest that candidates for bariatric surgery may have susceptibility to eating disorders. The importance of a multidisciplinary team in monitoring during the preoperative period is highlighted.

The rate of technical innovation, system interconnection, and advanced communications undoubtedly boost distributed energy networks' efficiency. However, when an additional attack surface is made available, the possibility of an increase in attacks is an unavoidable result. The energy ecosystem's significant variety draws attackers with various goals, making any critical infrastructure a threat, regardless of scale. Outdated technology and other antiquated countermeasures that worked years ago cannot address the complexity of current threats. As a result, robust artificial intelligence cyber-defense solutions are more important than ever. Based on the above challenge, this paper proposes an ensemble transfer learning spiking immune system for adaptive smart grid protection. It is an innovative Artificial Immune System (AIS) that uses a swarm of Evolving Izhikevich Neural Networks (EINN) in an Ensemble architecture, which optimally integrates Transfer Learning methodologies. The effectiveness of the proposed innovative system is demonstrated experimentally in multiple complex scenarios that optimally simulate the modern energy environment. In this way, the proposed system fully automates the strategic security planning of energy networks with computational intelligence methods. It allows the complete control of the digital strategies of the potential infrastructure that frames it, thus contributing to the timely and valid decision-making during cyber-attacks.

Cooperative Non-Orthogonal Multiple Access (NOMA) with Simultaneous Wireless Information and Power Transfer (SWIPT) communication can effectively improve the spectrum efficiency and energy efficiency of the wireless networks with extend coverage. An important design issue is to incentivize a relaying center user to participate in the cooperative process and achieve a win-win situation to both the BS and the center user. Some private information of the center users are hidden from the BS in the networks. We apply a contract theory-based incentive mechanism under such asymmetric information scenario to incentives center user to join the cooperative communication to maximize the BS profit utility and to guarantee the center user’s expect payoff. A match theory-based Gale-Shapley algorithm is proposed to obtain the optimal strategy with low computation complexity. Simulation results indicated the network performance of our proposed cooperative transmission is much better than the conventional NOMA transmission and the benefit utility of the BS with the stable match strategy is nearly close to the complete channel state information multi-users scenario while the center users get the satisfied expect payoffs.

The main aim of sustainable development is to ensure an intelligible and long-lasting balance between the economy, society, and the environment. Sustainable tourism could only be successful if the inter-relationships between all three dimensions are accepted. In the limited number of research analyses, the focus of the research is on competition between tourist countries and destinations. This study has used Game theory to analyze the competition applies time-series data in selected neighboring countries measure of a VAR-based spillover index, developed by [1] to investigate the time-varying relationship between tourism and Gross Domestic Product. Each country analyzed Vector Error Correction (VEC) and Granger analysis to explore the causal short and long-term tourism and use a sample that spans from 1997 to 2019. From the main results of Cholesky, the total spillover index is 59.0% between Russia and Mongolia which suggests a moderate interdependence among the four variables. Findings indicate that neither China nor Mongolia have a short-run influence on tourism development. China's inbound tourism is affected in the long run by Mongolia's inbound tourism but not vice versa can be explained by the fact that the number of tourists visiting Mongolia would include China in their travels.

In the field of railroad safety, effective detection of surface cracks is critical, necessitating reliable, high-speed non-destructive testing (NDT) methods. This study introduces a hybrid Eddy Current Testing (ECT) probe, specifically engineered for railroad inspection, to address the common issue of ’lift-off noise’ due to varying distances between the probe and test material. Unlike traditional ECT methods, this probe integrates transmit and differential receiver coils, aiming to enhance detection sensitivity and minimize lift-off impact. The study optimizes ECT probes employing different driver coils, emphasizing three main objectives: a) quantitatively evaluating each probe using signal- to-noise ratio (SNR) and outlining a real-time data processing algorithm based on SNR methodology; b) exploring the frequency range proximal to the electrical resonance of the receiver coil; c) examining sensitivity variations across varying lift-off distances. The experimental outcomes indicate that the newly designed probe with figure 8-shape driver coil significantly improves sensitivity in detecting surface cracks on railroads. It achieves an impressive SNR exceeding 100 for defects with minimal dimensions of 1 mm in width and depth. Simulation results closely align with experimental findings, validating the investigation of optimal operational frequency and lift-off distance for selected probe performance, determined to be 0.3 MHz and 0.5 mm, respectively. The realization of this project would lead to notable advancements in enhancing railroad safety by improving crack detection efficiency.

The effects of CO₂-water-rock interactions on the mechanical properties of shale are essential for estimating the possibility of sequestrating CO₂ in shale reservoirs. In this study, uniaxial compressive strength (UCS) tests together with an acoustic emission (AE) system and SEM & EDS analysis were performed to investigate the mechanical properties and microstructural changes of black shales with different saturation times (10 days, 20 days and 30 days) in water dissoluted with sub-/super-critical CO₂. According to the experimental results, the values of UCS, Young’s modulus and brittleness index decrease gradually with increasing saturation time in water with sub-/super-critical CO₂. Compared to intact samples, 30-days’ saturation causes reductions of 56.43% in UCS and 54.21% in Young’s modulus for sub-critical saturated samples, and 66.05% in UCS and 56.32% in Young’s modulus for super-critical saturated samples, respectively. The brittleness index also decreases drastically from 84.3% for intact samples to 50.9% for samples saturated in water with sub-critical CO₂, to 47.9% for samples saturated in water with super-critical carbon dioxide (SC-CO₂). SC-CO₂ causes a greater reduction of shale’s mechanical properties. The crack propagation results obtained from the AE system show that longer saturation time produces higher peak cumulative AE energy. SEM images show that many pores occur when shale samples are saturated in water with sub-/super-critical CO₂. The EDS results show that CO₂-water-rock interactions increase the percentages of C and Fe and decrease the percentages of Al and K on the surface of saturated samples when compared to intact samples.

A total of 27 microsatellites markers , scattered all over the genom of barley, were used for characterization,and diversity analysis in 33 barley (Hordeum vulgare L.) accessions and cultivars of Algeria.Over the 27 genetic loci studied, 110 alleles were identified with a mean of 4.1 alleles per locus and the average polymorphism information content (PIC) of 0.46,the marker Ebma0806 showed the greatest value of PIC with 0.83.Genetic diversity at 27 microsatellite loci varied from 0 to 0.84 (Mean=0.50) for 33 Algerian cultivars. The genetic distance among the cultivars ranged from 0.2 to 0.85. Cluster analysis and principal coordinate analysis (PCoA) based on the SSR data clearly differentiate the all genotypes studied.

The use of smart grids has enabled a number of planning methods to be developed to optimize energy costs, Peak to Average Ratios (PARs), and consumer satisfaction for load management in industrial, commercial, and domestic sectors. From a technical point of view, achieving optimal outcomes requires Demand Side Management (DSM). In smart grids, utility companies and electric users communicate two-way using digital technology to make a sustainable and economic system. This paper proposes a novel framework within which an Energy Management Controller (EMC) keeps track of each appliance, its operational time, and the costs associated with them. Customers of smart grids are motivated to shift their Off-Peak Hours (OPH) from Peak Hours by presenting incentives in OPH. The metering devices would also save customers costs by preventing load shifting between high- and low-cost periods. In addition, the study proposes the bacterial foraging algorithm and grasshopper optimization algorithm for lessening power price and PAR without compromising user comfort (UC) through appliance planning. The simulation results on a practical test system advocate the high effectiveness and reliable performance of the proposed model.

Concern about the planet's future has motivated governments around the world to adopt policies that promote more responsible energy consumption. Reducing emissions of the principal cause of climate change man-made greenhouse gases requires greater system efficiency and the utilization of renewable energy sources. The generation of electricity is the single largest source of hazardous pollutants, followed by the transportation sector. This is true due to the extreme reliance on petroleum and its derivatives that these industries have. Electric mobility is receiving more attention from businesses, governments, and academic institutions as a means to reduce the negative impacts of current energy consumption. Without measures to address common technical issues, electric vehicles would strain electrical infrastructure. In order to determine the best strategy for switching operations and feeder reconfiguration, this research presents a helpful hybrid genetic algorithm particle swarm optimization (HGAPSO) method. Meet transmission limits while decreasing real power losses and enhancing the system's bus voltage profile. The effects of HGAPSO on power losses and voltage distributions in the network are analyzed. Then, a report is produced contrasting GA and PSO. This cross-breeding of GA and PSO led to HGAPSO. This important problem can be solved more effectively with the use of new or improved algorithms. To find the optimal reconfiguration and properly rearrange transmission network interconnection, it employs a plethora of heuristic optimization algorithms. The objective is to limit bus voltage variations while maintaining the system's radial topology and minimizing power usage. The reliability and performance of the procedure were evaluated using MATLAB's IEEE 33-bus communication network. The outcomes demonstrate the effectiveness of the proposed technique, which cuts down on power waste during standalone runs and speeds up the processing time.

Reliability assessment in traditional power distribution systems has played a key role in power system planning, design, and operation. Recently, new information and communication technologies have been introduced in power systems automation and asset management, making the distribution network even more complex. In order to achieve efficient energy management, the distribution grid has to adopt a new configuration and operational conditions that are changing the paradigm of the actual electrical system. Therefore, the emergence of the cyber-physical systems concept to face future energetic needs requires alternative approaches for evaluating the reliability of modern distribution systems, especially in the smart grids environment. In this paper, a reliability approach that makes use of failure modes of power and cyber network main components is proposed to evaluate risk analysis in smart electrical distribution systems. We introduce the application of Failure Modes and Effects Analysis (FMEA) method in future smart grid systems in order to establish the impact of different failure modes on their performance. A smart grid test system is defined and failure modes and their effects for both power and the cyber components are presented. Preventive maintenance tasks are proposed and systematized to minimize the impact of high-risk failures and increase reliability.

An existing power grid is going through a massive transformation. Smart grid technology is a radical approach for improvisation in prevailing power grid. Integration of electrical and communication infrastructure is inevitable for the deployment of Smart grid network. Smart grid technology is characterized by full duplex communication, automatic metering infrastructure, renewable energy integration, distribution automation and complete monitoring and control of entire power grid. Wireless sensor networks (WSNs) are small micro electrical mechanical systems which are accomplished to collect and communicate the data from surroundings. WSNs can be used for monitoring and control of smart grid assets. Security of wireless sensor based communication network is a major concern for researchers and developers. The limited processing capabilities of wireless sensor networks make them more vulnerable to cyber-attacks. The countermeasures against cyber-attacks must be less complex with an ability to offer confidentiality, data readiness and integrity. The address oriented design and development approach for usual communication network requires a paradigm shift to design data oriented WSN architecture. WSN security is an inevitable part of smart grid cyber security. This paper is expected to serve as a comprehensive assessment and analysis of communication standards, cyber security issues and solutions for WSN based smart grid infrastructure.

Computer vision is a rapidly developing field that focuses on highly sophisticated picture analysis, manipulation, and comprehension. Its objective is to analyze what is happening in front of a camera and utilize that understanding to control a computer or robotic system or to present users with fresh visuals that are more enlightening or appealing than the original camera images. Computer vision technologies make it feasible for new user interfaces, augmented reality gaming, biometrics, automobile, photography, movie creation, Web search, and many more applications. This essay seeks to explain how computer vision can be utilized to play blackjack successfully.

This paper reviews the multiple roles of machine learning in improving the resilience of power grids, especially in applying new energy storage technologies. Energy storage technologies, such as compressed air energy storage, flywheel energy storage, and superconducting coil energy storage, significantly improve the power grid's ability to respond to load fluctuations and emergencies through intelligent control and optimisation of machine learning algorithms. This not only helps to optimise energy dispatch and improve the operational efficiency and flexibility of the grid but also significantly improves the stability and reliability of the grid so that it is better able to meet future challenges and needs.

Tungsten balls with sub-100-μm diameter can function as probe tips for micro-coordinate measuring machines (CMMs) to measure ultraprecise workpieces such as ceramic bearings with a high aspect ratio. A high-precision measuring system was proposed to evaluate the roundness error of the self-made tungsten ball tips. The principles and mathematical models of the measuring system are illustrated, and the fabrication principle of tungsten balls is introduced. An analysis was conducted on the maximum allowable contact force and bending strength of the tungsten ball tips, and the elastic mechanism was designed based on the analysis. A ruby probe with a sphericity error of 130 nm (A-5003-0577, Renishaw Corporation) used as a reference sphere was measured to verify the system's effectiveness. Repeated measurement experiments were performed for two tungsten ball tips. The results show the roundness error of the tungsten ball-A is between 568.3 and 586.2 nm with a standard deviation of 6.6 nm while the tungsten ball-B’s roundness error is between 898.5 and 958.0 nm with a standard deviation of 19.7 nm. The uncertainty is calculated as 125.8 nm. The developed system can stably measure the roundness of the tungsten ball tips.

Climate change and global warming are becoming important problems around the globe. To prevent these environmental problems, many countries try to reduce the emissions of greenhouse gases (GHG) and manage the consumption of energy. In Korea, Korea Electric Power Corporation (KEPCO) has introduced Smart Grid (SG) technologies to its branch office in 2014. This was the first demonstration of smart grid on a building called Smart Grid Station. This paper treats the achievements of the Smart Grid Station (SGS) by its early target in three aspects. The things are peak reduction, power consumption reduction and electricity fee saving. The authors analyzed the achievements by comparing the data of 2015 with the data of 2014. Through the evaluation, the authors studied the case, proved the advantages of SGS, and suggested the requirements to improve and the direction to go of the system.

We describe here the coherent formulation of electromagnetism in the nonrelativistic quantummechanical many-body theory. We use the mathematical frame of the field theory and its quantization in the spirit of the QED. This is necessary because of the manifold of misinterpretations emerging from the hystorical development of quantum mechanics, starting from the Schrödinger equation of a single particle in the presence of given electromagnetic fields, followed by the many-body theories of many charged identical particles having just Coulomb interactions inspired from the classical electromagnetic theory of point-like charges. However, this later is known to be inconsistent due to the self-interaction. This way could not be continued further to include properly the magnetic forces between the charged particles and lead to a lot of confusion about the interpretation of the magnetic field in the Hamiltonian, as well as about the gauge invariance. We emphasize the importance of the distinction between the applied (external fields) and the field in the matter. All these problems are length properly solved within the non-relativistic QED, nevertheless the confusion dominates in all the problems related to the magnetic properties of the solid state.

The incidence of right-turning pedestrian accidents is increasing in South Korea. Most of the accidents occurred when the larger vehicle was turning right, and the main cause of the accidents was found to be the driver's limited field of vision. After these accidents, the government has implemented a series of institutional measures with the objective of preventing such accidents. However, despite the institutional arrangements in place, pedestrian accidents continue to occur. We focused on the many limitations that autonomous vehicles, like humans, can face in such situations. To address this issue, we propose a right-turn pedestrian collision avoidance system by installing a LiDAR sensor in the center of the intersection to facilitate pedestrian detection. Furthermore, the urban road environment is considered, as this provides the optimal conditions for the model to perform at its best. During this research, we collected data on right-turn accidents using the CARLA simulator and ROS interface and demonstrated the effectiveness of our approach in preventing such incidents. Our results suggest that the implementation of this method can effectively reduce the incidence of right-turn accidents in autonomous vehicles.

This policy paper explores various strategies that would facilitate transitioning the traditional Jordanian electrical grid to a secure smart grid. It includes comprehensive recommendations from academia and industry for the regulatory and governmental sector in Jordan to achieve specific roadmap objectives. As Jordan is heavily dependent on fossil fuels, This policy paper also provides recommendations for incorporating more renewables into its energy mix, thereby facilitating a sustainable future. The proposed policies will emphasise the creation of an enabling environment where innovation, research, and development initiatives flourish, thereby promoting private sector engagement.

Small and Medium-scale Enterprises (SMEs) need a platform that actively enables collaboration with Research institutions and consultants since SMEs lack the financial resources to conduct independent research. Such a platform will require a verifiable manipulation-free system for enabling, executing, and recording collaboration activities and tracking reputations among the organizations and individuals that use the platform. Blockchain provides an opportunity to build such a collaborative platform by enabling the verifiable recording of outcomes from collaborations, aggregating the resulting reputation of the collaborating parties, and offering tokenised incentives for rewarding positive contributions to the platform. Cryptocurrencies from which blockchain-based tokens are highly unstable, thereby, reducing business organisations’ interest in blockchain applications. Hence, there is a need to design a self-sustaining valuable token model that incentivises user behaviours that positively contribute to the platform. This paper explores the application of game theory in analyzing token-based economic interactions between the various groups of users in a blockchain-based collaboration platform to design and simulate a token distribution system that provides a fair reward mechanism for the users while also providing a dynamic pricing model for the utility value provided by the platform tokens. Furthermore, the paper analyzed potential risks on the token model design and propose mitigation strategies.

In modern warfare, the diversified tasks can sometimes be challenging to fulfill with a single projectile, necessitating the incorporation of cooperation constraints in trajectory planning. Limited by the stringent requirements of the launch platform and lower costs, the maneuverability and ability to adjust the flight time range of projectiles are weak. Therefore, the rationality of performance indicators and flight time coordination strategies is especially critical. To fully exploit the control capabilities of projectiles, a battlefield area segmentation method is proposed, differentiated performance indicators and a cooperative trajectory planning model that considers the entire range of projectiles are established. Considering the limitations of existing flight time coordination strategies in applications, targeted improvements have been made in different cooperation scenarios, and a bi-level adaptive cooperation strategy(BACS) with both optimality and flexibility is proposed. To rapidly determine feasible conditions, a simple and universal method for obtaining the capability ranges of cooperation is introduced. The multi-phase optimal control problems are transformed into nonlinear programming problems using the Radau pseudo-spectral method, and simulation results show that the proposed methods are capable of handling trajectory planning tasks in different cooperation scenarios. The improved strategies effectively enhance the planning success rate under relatively harsh conditions and BACS demonstrates good compatibility with the problems studied.

The effects of heterogeneity of cooperative membership on cooperative and collective action sustainability has been previously discussed. However, despite the importance of membership heterogeneity in recent theoretical frameworks, empirical examinations have been limited. We determine the effect of changes to cooperative member heterogeneity on cooperative sustainability and discuss changes to heterogeneity overtime that can advance our understanding to cooperative sustainability long-term. This study uses USDA Agricultural Management Resource Survey data, coupled with USDA-Rural Development cooperative financial data at the state level, to quantify effects of cooperative member heterogeneity to sustainability of U.S. farmer cooperatives. We use random forest regression to interpret the significance of heterogeneity with cooperative sustainability at an aggregate level. The findings of this empirical study narrowly reconciles the theoretical understanding of the emergence of intra-cooperative issues while providing consistent empirical evidence and expectations for the sustainability of cooperatives in the near term.

This paper presents an analysis of the sensitivity of controlling an autonomous surface object among a group of encountered objects to the inaccuracy of state control process data. For this purpose, a safe and optimal model of the control process was defined. An algorithm for determining the optimal and safe trajectory of an object, based on the multi-object game model, was developed; for comparative analysis, an algorithm for calculating only the optimal trajectory, not taking into account the maneuverability of other objects, was additionally developed. First, simulation-based studies of the algorithms enabled a comparative analysis of a number of different acceptable strategies for optimally shifting the trajectory of maneuvering objects from a single initial direction. Thereafter, the main goal of this paper was implemented: an analysis of the sensitivity characteristics of safe control, assessed with the risk of collision, both on the inaccuracy of navigation data and on the number of possible control strategies. Finally, final conclusions and a plan for further research on the subject of the paper were formulated.

- Power grids of the future will likely incorporate more renewable energy distributed generation (REDG), also known as alternative energy systems. REDG units are increasingly being used in electrical transmission networks because to the overall positive effects they have on power networks. REDG systems are the backbone of smart electric networks and are essential to the operation of the smart grid. These REDG systems can additionally improve system reliability by providing some customers with a backup generator in the event of power interruptions. The report offers a thorough evaluation of the existing body of information on the topic of electric vehicles' (EVs') future interactions with the smart grid. The combination of the EVs' potential deployment and the smart grid's conceptual goal presents challenges in electric grid infra-structure, communication, and control. The proposal for connecting EVs to the grid is based on research into cutting-edge smart metering and communication systems. In the context of the vehicle-to-grid (V2G) phenomenon, the possibilities, benefits, and limitations of various EV smart charging systems are also fully examined. There is a fast growing percentage of distributed energy that is wind and solar photovoltaic. Their variable power output, however, introduces fresh challenges for those responsible for organizing, operating, and controlling the power grid. While fluctuations in the electric grid are problematic, they may be mitigated by the entry of EVs into the energy market. As such, we do a comprehensive literature search to learn more about the exciting research gap that needs to be filled and the most recent possible answer that involves EVs. Additionally, we take a close look at the practicality of the sophisticated V2G technology. The smart grid is a developing concept for the world's energy infrastructure, and this study analyzes in depth how EVs interact with it.

Backscatter communication, which transmits information by passively reflecting radio frequency (RF) signals, has become a focal point of interest due to its potential to significantly enhance the energy efficiency of Wireless Power Mobile Edge Computing (WPMEC) networks and extend the operational lifespan of terminal devices. However, there is little research on the integration of user cooperation in WPMEC scenarios within volatile network environments. In this paper, we propose a dynamic task offloading scheme for a Backscatter-assisted WPMEC system, which involves two mobile devices (MDs) and a Hybrid Access Point (HAP) with user cooperation. We formulate the energy efficiency (EE) maximization problem as a stochastic programming problem, considering the randomness of task arrivals and time-varying wireless channels. By leveraging Dinkelbach’s method and stochastic network optimization technique, we transform the problem into a series of deterministic sub-problems for each time slot, and convert the non-convex sub-problem into convex ones. We propose a low-complex EE maximization algorithm to solve the convex problems efficiently. Extensive simulations are conducted to validate the performance of our algorithm under various system parameter settings. Experiment results demonstrate that our algorithm not only outperforms the benchmark algorithms by approximately 23%, but also stabilize all queues within the MEC system.

Spent coffee grounds (SCG) have great potential as a useful, value-added biological material. In this context, activated carbon (AC) was prepared from SCG by an activation process using H3PO4 at 600°C in air and used as an adsorbent for the azo dye AO7, a model molecule for dye colorants found in textile industry effluents. X-ray diffraction, SEM and BET revealed that the AC was predominantly amorphous, consisting of a powder of 20-100 µm particles with mesopores averaging 5.5 nm in pore size. Adsorption kinetics followed a pseudo-second-order law, while the Langmuir model best fitted experimental isotherm data (maximum capacity of 119.5 mg AO7 per AC g). Thermodynamic parameters revealed that adsorption was endothermic and spontaneous. All the characterizations indicated that adsorption occurred by physisorption via mainly - interactions. The best experimental removal efficiency optimized by means of a Box-Behnken design and response surface methodology was 98% for an initial AO7 concentration of 20 mg.L-1 at pH 7.5 with a dose of 0.285 g.L-1 of AC and a contact time of 40 min. These results clearly show that activated carbon prepared from SCG can be a useful material for efficiently removing organic matter from aqueous solutions.

The insufficient flexibility of the hybrid renewable integrated energy system (HRIES) makes it difficult to accommodate renewable energy with a high proportion. It is thus necessary to excavate its potential flexibility to improve its operational performance and consume renewable energy. This paper unlocks the adjustment potential of flexible buildings and builds a flexible thermal load regulation model according to the dynamic thermal characteristics and thermal comfort elastic interval of the buildings and a regulation model of the flexible electrical load based on its transferability, resectability, and rigidity. An operation optimization model, which incorporates multiple flexible load regulations and the variable load of devices, is then developed. A case study is presented to analyze the regulation and synergy mechanism in different types of flexible loads. Its results show a saturation effect between the flexible thermal and electrical loads in increasing renewable energy consumption and a synergy effect in decreasing the total cost. This synergy can reduce the total cost by 0.73%. Besides, the total cost can be reduced by 15.13%, and the renewable energy curtailment rate can decrease by 12.08% if the flexible electric and thermal loads are integrated into the operation optimization of HRIES.

With the development of higher voltage power grid, the high and low voltage parallel loops are emerging, which lead to energy losses, even threaten the security and stability of power system. The multi-infeed HVDC configurations widely appearing in AC/DC interconnected power system make this situation even worse. Aimed at energy saving and system security, a decision optimization method for power grid operating condition with high and low voltage parallel loops is proposed in this paper. Firstly, considering hub substation distribution and power grid structure, parallel loop opening schemes are generated with GN algorithm. Then, candidate opening schemes are preliminarily selected from all these generated schemes based on a filtering index. Finally, with the influence on power system security, stability and operation economy in consideration, an evaluation model for candidate opening schemes is founded based on analytic hierarchy process (AHP). And a fuzzy evaluation algorithm is used to find the optimal scheme. Simulation results of New England 39-bus system and an actual power system validate the effectiveness and superiority of this proposed method.

Adaptation to climate change is being addressed in many domains. This means that there are multiple perspectives on adaptation; often with differing visions resulting in disconnected responses and outcomes. Combining singular perspectives into coherent, combined perspectives that include multiple needs and visions can help to deepen the understanding of various aspects of adaptation and provide more effective responses. Such combinations of perspectives can help to increase the range and variety of adaptation measures available for implementation or avoid maladaptation compared with adaptations derived from a singular perspective. The objective of this paper is to present and demonstrate a framework for structuring the local adaptation responses using the inputs from multiple perspectives. The adaptation response framing has been done by: (i) contextualizing climate change adaptation needs; (ii) analyzing drivers of change; (iii) characterizing measures of adaptation; and (iv) establishing links between the measures with a particular emphasis on taking account of multiple perspectives. This framework was demonstrated with reference to the management of flood risks in a case study Can Tho, Vietnam. The results from the case study show that multiple perspective framing of adaptation responses enhance the understanding of various aspects of adaptation measures, thereby leading to flexible implementation practices.

The aim of this article is to propose a core game theory model of transaction costs wherein it is indicated how direct costs determine the probability of loss and subsequent transaction costs. The existence of optimum is proven, and the way in which exposure influences the location of the optimum is demonstrated. The decisions are described as a two-player game and it is discussed how the transaction cost sharing rule determines whether the optimum point of transaction costs is the same as the equilibrium of the game. The dispute between actors regarding changing the share of transaction costs to be paid by each party is modeled by a non-cooperative bargaining game. Requirements of efficient transaction cost sharing rules are defined, and it is posited that solution exists which is not unique. Policy conclusions are also devised based on principles of design of institutions to influence the nature of transaction costs.

Smart Grid systems have become popular and necessary for the development of a sustainable power grid. These systems use different technologies to provide optimized services to the users of the network. Regarding computing, these systems optimize electrical services by processing a large amount of data generated. However, privacy and security are essential in this kind of system. With a large amount of data generated, it is necessary to protect the privacy of users, because this data may reveal users’ personal information. Today, blockchain technology has proven to be an efficient architecture for solving privacy and security problems in different scenarios. Over the years, different blockchain platforms have emerged, attempting to solve specific problems in different areas. However, the use of different platforms fragmented the market, which was no different in the smart grid scenario. This work proposes a blockchain architecture that uses sidechains to make the system scalable and adaptable. We used three blockchains to ensure privacy, security, and trust in the system. To universalize the proposed solution, we used the OSGP protocol and smart contracts. The results show that architecture security and privacy are guaranteed, making it feasible for implementation in real systems. Although scalability issues regarding the storage of data generated still exists.

In bacteria, enzymes usually comprise of enzymatic domains only. In eukaryotes/mammals, and here particularly in context of signal transduction, proteins with enzymatic functions contain additional modules promoting interactions with cooperating signaling proteins. Often such protein-protein interaction domains, such as SH2- and SH3-domains, help to localize the enzymatic function (e.g. kinase, phosphatase) to another protein, cellular compartment, or membrane nanodomain. In such cases, the interaction domain(s) serve(s) the enzymatic function. However, there are molecular situations in which an interaction domain fulfills its task completely independent of the protein´s enzymatic function and in this review, we call such function the adapter function of an enzyme. Though many stories can be told, we will concentrate on several proteins playing crucial roles in cells of the immune system, such as BTK, PI3K, and SHIP1, as well as in cancer cells, such as proteins of the RAS/ERK MAPK pathway. We will also discuss how these adaptor functions of enzymes determine or even undermine the efficacy of targeted therapy compounds, such as ATP-competitive kinase inhibitors, thereby highlighting the need to develop pharmacological approaches, such as PROTACs, that eliminate the entire protein. We also review how genetic kock-out and knock-in approaches can be leveraged to identify adaptor functions of signaling proteins.

Mechanically homogenized composite of expanded graphite and cobalt(II) rhenate(VII) has been described. Cobalt(II) rhenate(VII) was obtained in a reaction of perrhenic acid with cobalt(II) nitrate. A simple mortar homogenization method was used to enhance intercalation of cobalt species within carbon matrix. The specific capacity of composite was enhanced by 50% in comparison to bare expanded graphite. The electrochemical characteristic was significantly improved including better cyclability, lower resistance of electrode material, lower iR drop, with respect to expanded graphite without cobalt(II) rhenate(VII) active species. Expanded graphite with its unique specific surface area and pore size diameter was proved as potential and cheap carbon support.

Mobile Edge Computing (MEC) integrated with Wireless Power Transfer (WPT) is emerging as a promising solution to reduce task delays and extend the battery life of Mobile Devices (MDs). Cooperative user communication, or relay technology, enhances communication efficiency for users located far from the base station by mitigating the double near-far effect caused by distance. This is considered a key technology in Beyond 5G (B5G) and future communication systems. In this paper, we focus on maximizing the long-term energy efficiency (EE) of a user-cooperation WPT-MEC system, while taking into account the uncertain load dynamics at the edge MD and the time-varying state of the wireless channel. The joint optimization of wireless charging time fraction, MD offloading duration, helper node processing time, and transfer power decision presents significant challenges due to the coupling of data offloading among cooperative users and a volatile system environment. To address these challenges, we formulate the problem as a stochastic programming problem and propose an online control algorithm, DOUCA, to solve it. Our approach utilizes Dinkelbach’s method and Lyapunov optimization theory to decouple the sequential decision problem into a deterministic sub-problem for each time slot. For the sub-problem, we use variable substitution to convert the non-convex problem into a convex one, containing only a small number of variables, which can be efficiently solved. Furthermore, we provide a mathematical analysis of our algorithm’s performance. Extensive simulation results demonstrate the effectiveness of our proposed algorithm, as evidenced by an impressive energy efficiency improvement of over 20% compared to benchmark methods. Our algorithm also achieves a trade-off between EE and system stability.

To improve carbon efficiency for urban logistics service system composed of a third-party logistics service provider (3PLs) and an e-business enterprise, low-carbon operation game between them was studied. Considering low carbon technology investment cost and sales expansion effect of low carbon level, profit functions for both players were constituted. Based on their different bargaining capabilities, totally 5 types of game scenarios were designed. Through analytical solution, Nash Equilibria under varied scenarios were obtained. By analyzing these equilibria, 4 major propositions were given, in which, some key variables and system performance index were compared. Results show that the best system yields could only be achieved under the fully cooperative situation; limited cooperation only for carbon emission reduction would not benefit the system performance improvement; E-business enterprise-leading game’s performance overtook 3PLs-leading ones.

The construction safety risks (such as landslides or slumps) of the high-fill subgrade are characterized by uncertainty and variability. In order to ensure the construction safety of the high-fill subgrade of the expressway, a comprehensive risk assessment model of high-fill subgrade construction according to the combination weighting method based on game theory was established. Firstly, settlement rate, lateral differential settlement, horizontal displacement at the foot of the slope, deep horizontal displacement, and excess pore pressure were selected as evaluation indicators, and an evaluation index system of high-fill subgrade was constructed. Secondly, the subjective and objective weights were obtained via the analytic hierarchy process and entropy method. Furthermore, the optimized weights were obtained by introducing game theory, and the construction risk of the high-fill subgrade was evaluated and analyzed using the fuzzy comprehensive evaluation method. Finally, based on the high-fill section of the Zhijiang-Tongren Expressway in Hunan Province (China), the evaluation model was validated through field measurement data. The results show that the safety scores obtained using the three methods of analytic hierarchy process, entropy method, and combination weighting method based on game theory are similar. The combination weighting evaluation model can correct the evaluation result error caused by a single weight and avoid information delay caused by the manual processing and analysis of monitoring data. The high-fill subgrade safety evaluation grade based on the combination weighting method and game theory is consistent with the engineering situation, and its fault tolerance range is within 20%. The evaluation model proposed in this study can scientifically and effectively evaluate the safety risks of high-fill subgrade construction, significantly improving the safety and reliability during the construction process.

This paper proposes an optimization method for the scheduling of a multi-energy virtual power plant supply-demand balance in the power market environment of Jiangxi Province. The objective of this method is to enhance the operational efficiency of the power grid, reduce energy costs, and facilitate economical and efficient energy distribution in the power market. The method comprehensively considers the characteristics and uncertainties of renewable energy sources such as solar and wind energy, and incorporates advanced multi-objective optimization algorithms. Additionally, real-time market price feedback is integrated to achieve accurate allocation of power supply and demand. Through a case study of a multi-energy virtual power plant in Jiangxi Province, this paper examines the optimal combination model for various energy sources within VPP, and analyzes the impact of different market environments on supply-demand balance. The results demonstrate that the proposed scheduling optimization method significantly improves economic benefits while ensuring grid stability. Compared with traditional power supply models, it reduces average electricity costs by 15% and increases renewable energy utilization efficiency by 20%.