Non-impregnated small pore graphite (NSPG) with the compact microstructure for using in molten salt reactors (MSR) was prepared by the novel process, and the pore diameter of the obtained graphite was reduced to ~800 nm. The irradiation evaluation of the prepared graphite was carried out by 7 MeV Xe26+ ion irradiation and the microstructural changes of the graphite were investigated with IG-110 as a comparison. The graphitization degree of NSPG was higher than that of IG-110, though it was not subjected to an impregnation process. Under low-dose ion irradiation (

To address friction and wear challenges in dry contacts, manufacturers often employ self-lubricating materials. Graphite and its derivatives stand out as particularly suitable due to their exceptional tribological properties. However, under intense friction conditions, graphite can experience a decline in lubricating efficiency due to severe abrasive wear. This abrasive damage results in elevated activated carbon surfaces with increased surface energy, fostering greater adhesion between sliding surfaces. The low friction coefficient of graphite is not an inherent property but rather a consequence of water vapor adsorption by the material. Beyond 150°C, desorption of the vapor occurs, leading to a transition in the friction coefficient from µ=0.1 to µ=0.6. To address this issue, impregnation solutions for self-lubricating materials have been developed, with various compositions tailored to specific objectives. Common types include molybdenum disulfide, soft metals, or polymers. In this predominantly experimental study, the impact of polymer impregnation on the evolution of friction force and wear rate in graphite material bearings subjected to a dry fretting contact under severe thermal stresses at 270°C was investigated. Additionally, the mechanical stresses in the bearings throughout different phases of our tests were analyzed using a numerical model.

Recognizing the need to enhance immune cells' ability to target and eliminate tumor cells by focusing on tumor-associated antigens is crucial for the success of immunotherapy. Numerous cell-based therapies, such as CAR-T cell therapy, tumor-infiltrating lymphocyte (TIL) therapy, CAR-NK cell therapy, and T-cell receptor (TCR)-based therapies, are currently undergoing clinical and pre-clinical evaluation across various cancer types. However, a significant challenge lies in managing the inflammatory responses that are harmful to cancer patients. To overcome this, developing advanced strategies to target tumor cells precisely while preserving immune balance in cancer patients is imperative. One promising approach involves using modified tumor-associated macrophages (TAMs), which constitute approximately 50% of the tumor microenvironment (TME) and play a pivotal role in tumor progression. CAR-Macrophage (CAR-M) therapy is an emerging potential asset of immunotherapy for a wide range of tumors.

The European Green Deal poses a two-pronged challenge for the automotive industry: migrating to solutions based in light structures, requiring light weight concepts and light materials, while at the same time avoiding dependence towards the importation of these advanced materials. Aluminium alloys are lightweight and cost-effective materials that can successfully cover the requirements of many structural applications, however their production requires from bauxite and other Critical Raw Materials (CRM), such as Si and Mg. Aluminium alloys are fully recyclable, but scrap is usually contaminated and its use is related to an increment of impurities, tramp element and undesired inclusions. Traditionally, the use of secondary alloys has been restricted to low performance applications. The present work analyses the effect that the use of scrap has in the quantity of inclusions present in the alloy and in other properties relevant for the material processing. The study was carried out for common alloys belonging to 3 of the most common aluminium processes used in the car manufacturing industry: High Pressure Die Casting (HPDC) (EN AC-43500), extrusion (6063) and sheet metal forming (5754 and 6181). Reference alloy were mixed with different level of scrap (0, 20, 40, 60, 80 and 100%) trying to keep the chemical composition as unaffected as possible. The inclusions level of the alloy was characterized with the Prefil Foot-printer® test. In addition, the obtained materials, after being cast in an open mould, were subjected to metallographic characterization. Relevant properties to assess the formability quality of the alloys for the corresponding transforming process, were obtained: flowability test for HPDC alloy and high temperature compression for extrusion alloys. The results obtained suggest that the number of inclusions present in the melt highly increase with the amount of scrap used to produce the alloy. These inclusions are also related with an important lost of flowability, but do not have a noticeable impact on microstructure.

While the beneficial effects of using magnetic and electromagnetic treatment (ET) of brackish and saline waters on soil salinity reduction in the root zone were widely reported more studies are needed to answer questions about the soil salt leaching efficiency and the effect of the duration of the exposure to ET. For this aim, pot experiments were conducted using an Aqua-4DR physical water treatment device. The first experiment included two trials. The first considered 5 concentrations: C0:1.0; C1:4.5; C2:9; C3:13.5; and C4:18 dSm-1. The results revealed that the volume and the salt concentrations of the drained waters were significantly higher under irrigation with ET saline waters than those provided by untreated waters. The drained fraction of water varied from 20 to 26% under irrigation with untreated water and increased from 33 to 56% under irrigation with electromagnetized water indicating an improvement of salt leaching. The second trial was carried out with different irrigation doses. The result showed that the higher the dose, the more obvious and significant ET effect. The different treatment durations of water exposure revealed that the volume and salinity of drained water significantly increase as the ET duration increases. An increase in ET duration induces also an increase in soil water content of around 2.5%. Based on the experimental findings, we may conclude that the ET of saline water can reduce the adverse effect of salinity on the top soil, but these leached salts are carried away in depth and there is no concentration limit of water to the effect of the ET.

In this work, studies were carried out on the extraction of silver and gold from cakes of pressure oxidation leaching of sulfide concentrate containing pyrite and arsenopyrite. The addition of gypsum at a consumption of 0.1 g/g of concentrate helps to increase silver extraction from 13.4 to 95–98% at the cyanidation stage, with no conditioning operation. Gold recovery was 99%. An increase in gypsum consumption contributes to the formation of BFAS with an increased content of sulfate sulfur, and a decrease in the As/S(sulfate) molar ratio in the cake from 3.7 down to 0.88 contributes to an increase in silver extraction at the cyanidation stage up to 98%, and its further decrease from 0.88 down to 0.58 leads to a gradual reducing silver transfer into solution from 98 down to 75.1% at the cyanidation stage. Basic ferric sulfate (BFS) is not formed in this case, since according to EDS mapping the distribution of arsenic and sulfur over iron-containing particles is uniform. According to TCLP analysis, the cake obtained after pressure oxidation leaching with the addition of gypsum and cyanidation is stable and suitable for disposal, since the final concentration of arsenic in the solution was 0.45 mg/dm3.

In the field of railroad safety, effective detection of surface cracks is critical, necessitating reliable, high-speed non-destructive testing (NDT) methods. This study introduces a hybrid Eddy Current Testing (ECT) probe, specifically engineered for railroad inspection, to address the common issue of ’lift-off noise’ due to varying distances between the probe and test material. Unlike traditional ECT methods, this probe integrates transmit and differential receiver coils, aiming to enhance detection sensitivity and minimize lift-off impact. The study optimizes ECT probes employing different driver coils, emphasizing three main objectives: a) quantitatively evaluating each probe using signal- to-noise ratio (SNR) and outlining a real-time data processing algorithm based on SNR methodology; b) exploring the frequency range proximal to the electrical resonance of the receiver coil; c) examining sensitivity variations across varying lift-off distances. The experimental outcomes indicate that the newly designed probe with figure 8-shape driver coil significantly improves sensitivity in detecting surface cracks on railroads. It achieves an impressive SNR exceeding 100 for defects with minimal dimensions of 1 mm in width and depth. Simulation results closely align with experimental findings, validating the investigation of optimal operational frequency and lift-off distance for selected probe performance, determined to be 0.3 MHz and 0.5 mm, respectively. The realization of this project would lead to notable advancements in enhancing railroad safety by improving crack detection efficiency.

Graphite nanoplatelets (GNPs) were produced from flake graphite that had been immersed in isopropyl alcohol solution (70%) and converted to powder form in an ultrasonic bath (5 h, room temperature). Scanning and transmission electron microscopy, X-ray diffractometry, and Raman spectroscopy identified 120-nm-thick GNP crystallites and 0.5–21 µm plates with different areas and shapes. Extensive exfoliation was observed by transmission electron microscopy with abundant multilayer and some monolayer GNPs. X-ray diffractometry confirmed 43 GNP layers along the c-axis. Raman spectroscopy indicated well-defined GNPs with few defects and no oxide content. Rietveld analysis indicated a GNP crystal lattice with stacks of parallel two-dimensional graphene layers and tightly bound hybridized carbon atoms stacked in a translational …ABAB… sequence in hexagonal rings.

Nanocellulose (CNC) seems to be a promising surfactant, which, together with expandable graphite (EG), forms the essence of an effective natural-based fire retardant wood coating. In our research, the most suitable composition of the mixture was tested concerning good solubility, dispersion, and consistency. Favorable results were achieved with the formulation composed of a 4% CNC alkaline solution with 80 wt.% of selected EG. Subsequently, six different EG were used to prepare these wood fire retardant coatings. The effectiveness of treatments was verified using a test with a radiant heat source, where the test samples' relative weight loss, relative burning rate, and surface temperature during 600 sec were evaluated. All prepared formulations can be characterized as more or less equally effective. However, the best results were obtained with EG of GG 200 – 100 N, where the mass loss of the sample was 8.10 ± 1.24%. Very good results were also achieved by graphite 25 E + 180 HPH (8.70 ± 0.89%), which is similar to the previous one, even according to the microscopic assessment of the coating as well as the expanded layer. Graphite type 25 K + 180 (8.86 ± 0.65 %) shows the expanded layer's best cohesion, coating uniformity, and ease of application. The results of this work confirmed that the CNC coating itself has significant retardation effects.

Mechanically homogenized composite of expanded graphite and cobalt(II) rhenate(VII) has been described. Cobalt(II) rhenate(VII) was obtained in a reaction of perrhenic acid with cobalt(II) nitrate. A simple mortar homogenization method was used to enhance intercalation of cobalt species within carbon matrix. The specific capacity of composite was enhanced by 50% in comparison to bare expanded graphite. The electrochemical characteristic was significantly improved including better cyclability, lower resistance of electrode material, lower iR drop, with respect to expanded graphite without cobalt(II) rhenate(VII) active species. Expanded graphite with its unique specific surface area and pore size diameter was proved as potential and cheap carbon support.

Current paper is aiming to show the obtained results in manufacturing and characterization of graphite-based and metal composite materials suitable to be used in high voltage applications of automotive and/or aviation field. Thus, 4 types of materials have been processed and tested in order to assess their suitability to be used as current collector material for electric engines. The novelty of this work is the presentation of the new innovative technological process for obtaining the carbon/metal composite material used in the manufacture of sliding contacts for current collector heads, as well as the characteristics obtained for this material. All 4 obtained materials have been characterized from structural, mechanical and functional point of view and the most suitable of them has been chosen to be further developed by the end beneficiary.

This study investigated the impact of boron and copper on the microstructure and mechanical properties of Spheroidal graphite Cast Iron (SCI). The addition of boron increased the ferrite content, while copper increased the stability of pearlite. The interaction between boron and copper significantly increased the ferrite content. Differential Scanning Calorimetry (DSC) revealed that boron decreased the enthalpy change of the α + Fe3C -> γ transformation and increased the enthalpy change of the α -> γ transformation. The addition of boron and copper reduced the tensile and yield strength but increased elongation and impact energy. The findings provide valuable insights into the effect of boron and copper on SCI, facilitating the design and development of high-performance SCI materials.

Porous graphite was prepared without the use of template by rapidly heating the carbonization products from mixtures of anthracene, flourene, and pyrene with a CO₂ laser. Rapid CO₂ laser heating at a rate of 1.8 × 10 ⁶ °C/s vaporizes out the fluorene-pyrene derived pitch while annealing the anthracene coke. The resulting structure is that of graphite with 100 nm spherical pores. The graphitizablity of the porous material is the same as pure anthracene coke. Transmission electron microscopy revealed that the interface between graphitic layers and the pore walls are unimpeded. Traditional furnace annealing does not result in the porous structure as the heating rates are too slow to vaporize out the pitch, thereby illustrating the advantage of fast thermal processing. The resultant porous graphite was prelithiated and used as an anode in lithium ion capacitors. The porous graphite when lithiated had a specific capacity of 200 mAh/g at 100 mA/g. The assembled lithium ion capacitor demonstrated an energy density as high as 75 Wh/kg when cycled between 2.2 V to 4.2 V.

Modification of electrode surface with a selective layer gives the possibility to detect target ana-lytes of forensic interest. 3-(4-trifluoromethyl)-phenyl)-thiophene (ThPhCF3) was deposited on a graphite (G) electrode by electrochemical oxidation and characterized as a receptor for the recognition of synthetic stimulants (2-aminoindane, buphedrone, naphyrone). First, the structural characterization of the polymeric layer were obtained from Raman spectroscopy. Second, the electrochemical profiles of selected synthetic stimulants and their affinity to ThPhCF3/G-modified electrodes were studied using square wave voltammetry and electrochemical impedance spec-troscopy. The values of the adsorption constant show the importance of – PhCF3 groups in the interaction with synthetic stimulants, namely recognition by the formation of hydrogen bonds (Kads (buphedrone) < Kads (2-AI)) and interaction with aromatic H atoms (Kads (buphedrone) < Kads (naphyrone)). It was demonstrated that the polymeric layer derived from thiophene with – PhCF3 group is capable to increase the intensity of the electrochemical signal.

Sialylated milk oligosaccharides (SMOs) is the most important oligosaccharides in human milk oligosaccharides (HMOs), and have a multifunctional health benefit, and the most abundant SMOs are sialyllactose (SLs). The previous studies indicate that the growth of tumor cells, and angiogenesis on tumor tissues with Lewis lung carcinoma, melanoma, and colon carcinoma cells could be prevented by SL. Thus, it has been proposed that SL might be an ideal candidate for the development of anti-angiogenic drugs without any side effects. It has been proposed that the Sialic acid (Sia) can be produced through SL’s hydrolysis, and the dietary Sia is further transported to the brain and other tissues though blood for formation of CMP-Sia, the activated precursor of Sia, and then is catalyzed by polysialyltransferases (polySTs) for synthesis of polysialic acid (polySia) or polysialylation of neural cell adhesion molecule (NCAM). Thus, it’s necessary to study and develop new inhibitors, which not only modulate a proper balance between the gut health and neuros system development, but also inhibit the overexpression of polySia, and thus block the tumor cell migration. In this study, we proposed that 3’-SL and 6’-SL may be more ideal inhibitors comparing with two previous inhibitors, the low molecular weight heparin (LMWH) and cytidine monophosphate (CMP) in the previous studies.

Recently published structural analysis and galvanomagnetic studies of a large number of different bulk and mesoscopic graphite samples of high quality and purity reveal that the common picture assuming graphite samples as a semimetal with a homogeneous carrier density of conduction electrons is misleading. These new studies indicate that the main electrical conduction path occurs within 2D interfaces embedded in semiconducting Bernal and/or rhombohedral stacking regions. This new knowledge incites us to revise experimentally and theoretically the diamagnetism of graphite samples. We found that the $c$-axis susceptibility of highly pure oriented graphite samples is not really constant but can vary several tens of percent for bulk samples with thickness $t \gtrsim 30~\mu$m, whereas by a much larger factor for samples with smaller thickness. The observed decrease of the susceptibility with sample thickness resembles qualitatively the one reported for the electrical conductivity and indicates that the main part of the $c-$axis diamagnetic signal is not intrinsic of the ideal graphite structure but it is due to the highly conducting 2D interfaces. The interpretation of the main diamagnetic signal of graphite agrees with the reported description of its galvanomagnetic properties and provides a hint to understand some magnetic peculiarities of thin graphite samples.

Microbial infections in wounds can significantly delay the healing process, with bacteria often forming protective biofilms that shield them from external threats. In this study, we evaluated the impact of copper oxide-impregnated wound dressings (referred to as COD) on a bacterial mixture comprising common gram-positive and gram-negative wound pathogens encased in biofilm. The bacterial mix was exposed to COD or control dressings for 0, 1, 2, and 3 hours, and the effects were analyzed using scanning electron microscopy. After just 1 hour of exposure to COD, notable leakage of bacterial cytoplasmic contents was observed. By the 3-hour mark, the gram-negative bacteria exhibited formation of holes in their cell walls, while gram-positive bacteria showed a reduction in cell width. These findings demonstrate the ability of COD to effectively kill bacteria, even when protected by biofilm, supporting clinical observations of its efficacy in managing infected wounds.

The expression of polysialic acid (polySia) on the neuronal cell adhesion molecule (NCAM), is called NCAM-polysialylation, which is strongly related to the migration and invasion of tumor cells and with aggressive in the clinic. Thus, it’s important to select a proper drug to block tumor cell migration for clinic treatment. In this study, we proposed that lactoferrin (LFcinB11) may be a more ideal candidate for inhibition of NCAM polysialylation comparing with CMP and low molecular weight heparin (LMWH), which were determined based on our NMR studies. On the other hand, because neutrophil extracellular traps (NET) is the most dramatic stage in cell death process, and NETs’ release are related to pathogenesis of autoimmune and inflammatory disorders, with proposed involvement in glomerulonephritis, chronic lung disease, sepsis and vascular disorders. In this study, the molecular mechanism of inhibition of NETs’ release using LFcinB11 as inhibitor was also determined. Based on these results, LFcinB11 is proposed to be bifunctional inhibitor for inhibiting both NCAM polysialylation and NETs releases.

CoCrFeNiMn high-entropy alloy coatings were prepared on compacted graphite iron（CGI） through plasma cladding to strength the CGI substrate. The effects of heat treatment temperatures and times on the microstructure and mechanical properties of the CoCrFeNiMn coatings were investigated. After heat treatment, a single FCC phase was remained in the coating as compared to the deposited one, with smaller dendrites, larger dendritic spacing and more Cr-rich compounds precipitated between dendrites. The coatings’ microhardness was increased after heat treatment. After heat treated at 660°C for 90 minutes, the coating had the highest microhardness of 563±6.9 HV0.2, the lowest frictional coefficient of 0.71 and the smallest wear mass loss of 1.12 mg, and it had the best wear resistance.

We propose novel spectrometer designs that aim to enhance the measured spectral range 1 of ions on a finite-sized detector. In contrast to the traditional devices that use uniform magnetic 2 field, in which the deflection of particles increases inversely proportional to their momentum, in a 3 gradient magnetic field, the deflection of particles will be decreased due to the reduction of the 4 magnetic field along their propagation. Low energy ions are particularly impacted, as they are 5 deflected less and are more likely to reach the detector compared to being driven out of it while 6 using a uniform magnetic field. By the means of a gradient magnetic field, the nonlinear dispersion 7 of ions in a homogeneous magnetic field can approach a nearly linear dispersion. Nonetheless, 8 the dispersion of low energy ions in a homogeneous magnetic field remains unnecessarily high. 9 In this article, we explore linear, quadratic, and higher-order field profiles in comparison to the 10 homogeneous field case. We discuss the employed methodology and present simulation results of 11 the spectrometer with an extended ion spectral range, focusing on the minimum detectable energy 12 (energy dynamic range) and energy resolution

As one of the typical deposits in Sichuan-Yunnan-Guizhou Pb-Zn metallogenic province, the Daliangzi Pb-Zn deposit has a close genetic relation with the structural system of “black/fracture zone” formed under the action of NWW-approx. EW strike-slip structures in the metallogenic province, but the mechanism of rock and ore-controlling action of the structural system remains unclear. Based on detailed analysis of tectonite-mineralized alteration lithofacies of R1 “black/fracture zone”, the tectonite-mineralized alteration lithofacies zones can be divided into 4 types in succession outward from the Pb-Zn mineralization center, i.e., ① brecciated and stockwork-like Pb-Zn mineralization-complex breccia facies zone, ② stockwork-like Pb-Zn mineralization-simple breccia and cataclasite facies zone, ③ veined pyrite-sulfide-dolomitic cataclasite facies zone, and ④ fine-veined calcite-black carbonized dolomite facies zone; Cl- and SO42--rich high-temperature oxidizing ore-bearing fluid mixes with reducing fluid in Zone ① while migration and precipitation occur in Zone ④. With the evolution of ore-forming fluid, the homogenization temperature decreases from Zone ① to Zone ④, the salinity increases from Zone ① to Zone ② and then decreases to Zones ③ and ④, and the fluid density has little change on the whole; the contents of Zn, Pb, Cu, Ga, Ge, Cd, Ag, and other metallogenic elements, the Zn/Pb ratio, and the CaO/MgO mole ratio decrease gradually from Zone ① to Zone ④; and REE fractionation, calcilization, silicification, and pyritization enhance gradually from Zone ① to Zone ④. This series of changes are the product of diapirism (cryptoexplosion) of strike-slip structures and “black/fracture zone”, among which the second-order structures (F5, F100, and other faults) derived from NWW-approx. EW striking dextral shear-tension faults F1 and F15 control the brecciated and stockwork-like Pb-Zn mineralized complex breccia facies zones and the stockwork-like Pb-Zn mineralized simple breccia and cataclasite facies zones. Therefore, this paper establishes the zoning mode of tectonite-mineralized alteration lithofacies of “black/fracture zone” and proposes that Zones ① and ② are important prospecting criteria. conclusions.

This study examines the impact of the impregnation of fireclay-based conventional (CC) and medium cement castables (MCC) with liquid sodium silicate glass under vacuum conditions. The goal is to assess how this treatment affects physical, mechanical properties, and durability (alkali and thermal shock resistance) of these castables used in biomass combustion boilers, where they are exposed to temperatures up to 1100°C. The research work employs standard test methods to evaluate physical and mechanical properties. Additionally, advanced techniques such as scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDS), X-ray diffraction (XRD), and specific tests for alkali resistance and thermal shock resistance are used. The research findings suggest that impregnation with sodium silicate glass under vacuum significantly enhances the alkali resistance of both CC and MCC castables. This improvement is primarily due to the reduction in porosity and the increase in density. SEM images reveal that impregnated samples are coated with a glassy layer and the pores are partially filled with sodium silicate. Tests for alkali resistance demonstrate the formation of a protective glassy layer (with a thickness of 0.9-1.5 mm) on the castables surfaces, thereby reducing further penetration of alkali into deeper layers of the samples. However, it is important to mention that impregnated refractory castables have reduced resistance to thermal shock cycles.

Introduction: Silver nanoparticles have been extensively investigated in dental and orthopedic materials. However, the impregnation of bone graft with silver nanoparticles has been poorly investigated. Objectives: The aim of this study was to evaluate the in vitro antibiofilm activity of a bovine bone impregnated with silver nanoparticles. Methods: Bone scaffolds from cancellous bovine femur were used for the tests and impregnated with silver nanoparticles (50nm) by physical adsorption. Silver nitrate minimal inhibitory and bactericidal concentration were performed Staphylococcus aureus, Pseudomonas aeruginosa, Candida albicans, Enterococcus faecalis, Acinetobacter baumannii, and Escherichia coli. Disc diffusion tests for silver nanoparticles susceptibility and quantification of biofilm production on plate and bone with sessile cell count were also performed. Results: All pathogens were susceptible to silver with low minimal inhibitory concentration (0.25 – 4 mg/L). The scaffold impregnated with silver nanoparticles presented a significant reduction in the biofilm cells for all microorganisms with a reduction of more than 3 logs in colony forming units count. Conclusion: Bone scaffolds impregnated with silver nanoparticles can significantly reduce biofilm, and it can be a strategical material to be used as an implant for different approaches.

Background: Number of joint infections caused by Vancomycin-resistant pathogens is emerging. Currently no PMMA cement is commercially available to cover VRE. Daptomycin shows promising results in infection treatment, offers a good safety profile and reduced risk for resistance development. Purpose of this in vitro study is to investigate the mechanical stability, handling properties, elution behavior and antimicrobial effectiveness of PMMA cement loaded with three different Daptomycin concentrations in comparison to commercially available ALBC; Methods: Mechanical properties and handling characteristics (ISO 5833, DIN 53435), HPLC elution, antimicrobial effectiveness with proliferation assay (DIN 17025) and inhibition zone testing were investigated; Results: All tested Daptomycin concentrations fulfilled ISO and DIN mechanical strength. Dosage of 0.5. g added Daptomycin did not show any antimicrobial effectiveness in contrast to 1.0 g and1.5 g. Cement with 1.5 g Daptomycin was best in elution and effectiveness, showed good mechanical ISO strength, ISO doughing was a little longer sticky and setting was faster as Vancomycin containing reference cement; Conclusion: PMMA cement containing 0.5 g Gentamicin and 1.5 g Daptomycin could be a good alternative to the already established COPAL® G+V for PJI treatment of VRE.

Wounds are structural and functional disruptions of the skin that occur because of an accident. Chronic wounds are caused by a breakdown in the finely coordinated cascade of events that occurs during wound healing. Wound healing is a long process that split into at least three continuous and overlapping processes: an inflammatory response, a proliferative phase that leads to tissue repair, and third one is tissue remodeling. Therefore, wound healing studies are extensively studied to develop techniques that can achieve maximum recovery with minimum scar. Several growth hormones and cytokines secreted at the wound site tightly regulate wound healing processes. The traditional approach for wound management has been represented by topical treatments. Metal nanoparticles (e.g., silver, gold, zinc) are increasingly being employed in dermatology due to their favorable effects on wound healing, as well as in treating and preventing bacterial infections. The development of wound dressings materials has now been used to overcome the issues of external environments. The impregnated nanomaterials have provided moist environment that removes the exudates and avoid maceration. This review highlights the mechanism and focus on the current advancement of various nanoparticles impregnation material for wound healing process that can protect wound from infection and maintain the optimum exchange of gases.

Graphene oxide was synthesized by a one-step environmentally friendly mechanochemistry process directly from graphite and characterized by Raman, FT-IR and UV/vis spectroscopies, Atomic Force Microscopy, X-ray Diffraction, Scanning Electron Microscopy, Energy-Dispersive X-ray Spectroscopy and Thermogravimetric Analysis. Spectroscopic analysis shows that the functional groups and oxygen content of the synthesized material are comparable with those of graphene oxide synthesized by other previously reported methods (Hummers). Thermogravimetric analysis reveals thermal stability up to 400 °C.

On the system Au(III)-HCl-A324H⁺Cl^-, liquid-liquid extraction experiments were used to define the extraction equilibrium and the corresponding extraction constant, and the facilitated transport of this precious metal, from HCl solutions, across a flat-sheet supported liquid membrane was investigated, using the ionic liquid as carrier, as a function of hydrodynamic conditions, concentration of gold(III) (0.01-0.1 g/L), and HCl (0.5-6 M) in the feed phase, and carrier concentration (0.023-0.92 M) in the membrane. An uphill transport equation was derived considering aqueous feed boundary layer diffusion and membrane diffusion as controlling steps. The aqueous diffusional resistance (Δf) and the membrane diffusional resistance (Δm) were estimated from the proposed equation, being their values 241 s/cm an 9730 s/cm, respectively. The performance of the present carrier was compared against results yielded by other ionic liquids, and also it was investigated the influence that other metals had on gold(III) transport both from binary or quaternary solutions. Gold was finally recovered from receiving solutions as zero valent gold nanoparticles.

Heating films were prepared by using poly(methyl methacrylate) and polybutadiene composites containing graphite. The heating film was prepared by casting the as-made polymer composite on PET film. Copper electrodes were attached to both ends of the as-prepared film, and the heating characteristics of the film was analyzed while applying DC voltage. The electrical conductivity and the heating temperature of the heating films depended on the size, the structure, the content and the dispersion characteristics of the graphite in the composite. The electrical resistance of the heating film was controlled to adjust the heating temperature of the film. The relationship between the physical/chemical structure and the heating characteristics of the composite film was studied by measuring the heating temperature as functions of film thickness and resistance by using an infrared thermal imaging camera. The lower the film resistance, the higher the heating temperature of the film. The surface temperature was uniform throughout the film.

Graph theory plays a crucial role in modeling and designing of chemical structure or chemical network. Chemical Graph theory helps to understand the molecular structure of molecular graph. The molecular graph consists of atoms as vertices and bonds as edges. Topological indices capture symmetry of molecular structures and give it a mathematical language to predict properties such as boiling points, viscosity, the radius of gyrations etc. In this article, we study the chemical graph of carbon Crystal structure of graphite and cubic carbon and compute several degree-based topological indices. Firstly we compute M-Polynomials of these structures and then from these M-polynomials we recover nine degree-based topological indices.

Cycling reliability is crucial for Si-based materials due to severe volume change during cycles that results in the fast capacity fading. Though the binder only occupies a very low amount of the total mass of anodes, it is proved to perform a key parameter to improve the cycle performance of Si-based anodes. Because they are eco-friendly and cost saving, water-based binders styrene-butadiene rubber (SBR) and carboxymethyl cellulose (CMC) are regarded as the better binder to substitute Poly (vinylidene difluoride) (PVDF) as the binder for Si-based anode. In this study, the anodes are fabricated by simply mixing the active materials (naso Si, graphite and conductive additive) together and using the mixture of SBR and CMC as a binder. The results showed that the retention capacities of the anodes are more than 440 mAh/g after 400 cycles. It indicates that it is an easy and simple way to make high performance anodes.

This research is concentrated on the physical technique of carbon activation from carbon-based material such as bamboo. In addition, we impregnated the activated carbon by use of experimental methods. In the first case, the results from various parameters on the carbon activation process, such as kiln rotation speed, steaming time, calcination temperature and heating rate at the different levels has been investigated on iodine number of activated carbon. Using the Taguchi method and ANOVA analysis, the optimal test results were obtained which are as follows: steaming time and calcination temperature were the most influential factors and heating rate and kiln rotation speed were the less influential factors in the process. In the second case, palladium-impregnated activated carbon (Pa/AC) was prepared at different conditions of the experiment and effects of optimum ratios on the responses have been studied.

Carbon fiber reinforced polymers (CFRPs) are being used extensively in modern industries that require high strength-to-weight ratio such as aerospace, automotive, motorsport, and sports equipment. However, although reinforcement with carbon fibers improves the mechanical properties of polymer, this comes on the expense of abrasive wear resistance. Therefore, to efficiently utilize CFRPs in dry sliding contacts, solid lubricant is used as a filler. Further, to facilitate fabrication of objects with complex geometries, selective laser sintering (SLS) can be employed. Accordingly, in the present work, graphite-filled carbon fiber-reinforced polyamide 12 (CFR-PA12) specimens were prepared using SLS process to explore the dry sliding friction and wear characteristics of the composite. The test specimens were aligned along four different orientations in the build chamber of SLS machine to determine the orientation-dependent tribological properties. The experiments were conducted using pin-on-disc tribometer to measure the coefficient of friction (COF), interface temperature, friction-induced noise, and specific wear rate. In addition, scanning electron microscopy (SEM) of tribo-surfaces was conducted to specify the dominant wear pattern. The results indicated that the steady state COF, contact temperature, and wear pattern of graphite-filled CFR-PA12 are orientation-independent, and that the contact temperature is likely to approach an asymptote far below the glass transition temperature of amorphous PA12 zones, thus eliminating the possibility of matrix softening. Additionally, the results showed that the Z-oriented specimen exhibits the lowest level of friction-induced noise along with the highest wear resistance. Moreover, SEM of tribo-surfaces determined that abrasive wear is the dominant wear pattern.

The use of interleaving material with viscoelastic properties is one of the most effective solutions to improve the damping capacity of CFRP laminates. Improving composite damping without threatening mechanical performance is challenging and the use of nanomaterials should lead to the target. In this paper, the effect of a nanostructured interlayer based on Graphite Nanoplatelets (GNPs) on the damping capacity and fracture toughness of CFRP laminates has been investigated. High-content GNP/Epoxy (70wt/30wt) coating was sprayed on the surface of CF/Epoxy prepregs at two different areal weight (10 and 40 g/m2) and incorporated at the middle-plane of a CFRP laminate. The effect of the GNP areal weight on viscoelastic and the mechanical behaviour of the laminates was investigated. Coupons with low-areal weight GNP interlayer showed a 25% increase in damping capacity with a trivial reduction of the elastic modulus. Moreover, a reduction in interlaminar shear strength (ILSS) and fracture toughness (both mode I and mode II) was observed in the composites with GNPs interlayer. GNPs alignment and degree of compaction reached during process were found as key parameters on material performances. By increasing the areal weight a mitigation on the mechanical performances drop was achieved (-15%).

Lung cancer (LC) continues to be an important public health problem being the most common form of cancer and a major cause of cancer deaths worldwide. Despite the great bulk of research to identify genetic susceptibility genes by genome-wide association studies, only few loci associated to nicotine dependence have been consistently replicated. Our previously published study in few phenotypically discordant sib-pairs identified a combination of germline truncating mutations in known cancer susceptibility genes in never smoker early-onset LC patient does not present in their healthy sib. These results firstly demonstrated the presence of an oligogenic combination of disrupted cancer predisposing genes in non-smokers patients, giving experimental support to a model of a “private genetic epidemiology”. Here, we used a combination of whole-exome and RNA sequencing coupled with a discordant sib’s model in a novel cohort of pairs of never-smokers early-onset LC patients and in their healthy sibs used as controls. We selected rare germline variants predicted as deleterious by CADD and SVM bio-informatics tools and absent in the healthy sib. Overall, we identified an average of 200 variants per patient, about 10 of which in cancer predisposing genes. In most of them, RNA sequencing data reinforced the pathogenic role of the identified variants showing: i) downregulation in LC tissue (indicating “second hit” in tumor suppressor genes); ii) upregulation in cancer tissue (likely oncogene); iii) downregulation in both normal and cancer tissue (indicating transcript instability). The combination of the two techniques demonstrates that each patient has an average of six (with a range from four to eight) private mutations with functional effect in tumor predisposing genes. The presence of a unique combination of disrupting events in the affected subjects may explain the absence of familial clustering of non-small cell lung cancer. In conclusion, these findings indicate that each patient has his/her own “predisposing signature” to cancer development and suggest the use of personalized therapeutic strategies in lung cancer.

The focus of this study was to evaluate the effectiveness of incorporation of phenolic compounds from blueberry juice into pear slices using a combination of ohmic heating (OH) and vacuum impregnation (VI), followed by air- or freeze-drying. The results showed that OH is a valuable technique to increase the content of bioactive compounds and antioxidant capacity of blueberry juice. The optimal OH treatment is heating the juice at 50 °C for 20 min under an electric field of 13 V/cm. Furthermore, the combination of VI and OH showed the efficiency of enriching pear slices with bioactive compounds from blueberry juice. The best treatment is to immerse the slices for 90 min at 50 °C and an electric field of 7.8 V/cm. The presence of anthocyanin pigments from blueberry juice affects the color parameters of pear slices by increasing the a* parameter and decreasing the b* and L* parameters. However, both freeze-drying and air-drying (at temperatures of 40, 50, and 60 °C) negatively affected the phenolic content and antioxidant capacity. Notably, air-drying at 60 °C highest levels of phenolic compounds and antioxidant potential for both impregnated and non-impregnated pear slices among the drying processes applied.

Introduction: Infections associated with medical implants pose significant challenges to healthcare, demanding the development of new effective antimicrobial strategies. This study focuses on the creation of a novel biological membrane with enhanced antimicrobial properties by with the incorporation of either vancomycin or silver nanoparticles. Methods: Pericardium samples were impregnated with either silver nanoparticles (AgNPs) or vancomycin (VAN). The antimicrobial activity of the membranes was assessed through qualitative microbiological analysis, biofilm production and animal in vivo model of infection. Histological analysis was performed on the pericardium samples, and quantitative microbiological analysis was conducted on the tissue from the animal model and biocompatibility evaluation. Statistical analyses were carried out using appropriate tests. Results: Microbiological tests confirmed both VAN and AgNP showed inhibition halos against bacteria. Histological analysis indicated minimal inflammatory response and bacterial presence in VAN and AgNP groups compared to the control group revealed reduced bacterial presence. Biomechanical testing showed that polypropylene had the lowest tensile strength, while AgNP-impregnated pericardium exhibited lower resistance than VAN-impregnated and control pericardium. Conclusion: Lyophilized and decellularized bovine pericardium as a substrate, combined with the incorporation of vancomycin or silver nanoparticles, provides a versatile platform for combating infections associated with medical implants.

The focus of this work lies in the construction of monitoring system designed in the form of a patch using a long-lasting potentiometric electrolyte concentration sensor from metal electrodes, in a galvanic cell configuration Mg(s)|NaCl(aq)|Cu(s). Initially, a mathematical analysis was conducted on the expected sensor output through the Nernst equation. The experimental phase involved conducting controlled tests in the laboratory using various molar concentrations of sodium chloride (NaCl) in aqueous solution. Results showed that the electrolyte sensor allows for monitoring electrolyte levels in NaCl in the range of 0.02 to 1 M/L, with electrode lifespan exceeding 10 days. On the other hand, when patch is using human sweat during controlled exercise routines, it showed the sensor's capability for monitoring changes in the subjects' hydration levels in real time. The sensor output potential is greater than 1.7 volts when the sensor electrodes are in contact with human sweat, which is equivalent to measuring molar concentrations at normal hydration and moderately high hydration levels. Sensor results indicate that the system can function in a self-powered manner without external batteries. Additionally, the extended lifespan of its electrodes allows for continuous monitoring of imbalances in the human body, showcasing the system capability for long-term health assessment.

Microplastics (plastic particles &lt; 5 mm) are ubiquitous pollutants that pose the ability to carry microbiota, including pathogens. Microbial adhesion is usually a sign of pathogenicity, thus we investigated the adherent strains found on 4 mm nylon strips, which were ingested and excreted by wild fish specimens. Polymer analysis of the excreted samples shown no signs of degradation, nor have their controls, represented by the nylon strips submerged in the same water tanks. Both the ingested samples and controls presented pathogens in large numbers, revealing the fact that nylon microplastics can be physical carriers for pathogens in the aquatic environment.

In the aerospace sector, structural and non-structural components are usually subjected to a wide range of environmental conditions. Although lightweight, the use of composite parts for these applications is restricted, due to their poor performance in severe environmental conditions. Specifically, moisture can seriously damage the materials' performance, reducing their mechan-ical, thermal, electrical, and physical properties as well as the service time. A strategy to improve the materials’ resistance in humid environments is the use of protective lightweight barrier coatings to reduce the diffusion of gases and/or liquids in composites. Nanolamellar nanocom-posite characterized by the high in-plane orientation of nanoplatelets effectively works as barrier structures by generating tortuous paths for molecule diffusion. In this work, the effectiveness of protection against water uptake of nanocomposites reinforced with Graphite NanoPlatelets (GNPs) at high filler content (70, 80 and 90%wt) for Kevlar sandwich panels of a nacelle engine of an ATR42 aircraft has been investigated. Moisture uptake and Ground Air Ground (GAG) tests were carried out in an environmental chamber to reproduce temperature and relative humidity profiles representative of a real-scale application for a regional aircraft composite part. The high filler content of the graphene films ensures a high level of tortuosity by delaying and reducing moisture absorption by –71% compared to the unprotected panel, showing good barrier properties.

In this study, graphite, the most stable form of carbon, was examined for its hexagonal crystalline structure with specific dimensions (ao=2.46 Ǻ; co=6.70 Ǻ). Its framework comprises parallel carbon atom planes forming regular hexagons (side length 1.415 Ǻ) and 120° angles between adjacent atoms. Two structural variations exist: hexagonal symmetry (1-2-1-2-1-2 planes) and rhomboidal symmetry (1-2-3-1-2-3 planes). The research aimed to produce high-density graphite utilizing carbonaceous raw materials. Graphite-based materials often exhibit high porosity, necessitating additional treatments. The study successfully obtained mesophase tar pitch (yield: 45%), a pivotal raw material, and high-density graphite. The resulting graphite underwent characterization for physical properties (apparent and real density, porosity and compression strength), demonstrating conformity with existing literature data.

In this study, Ni50Ti50 powder was coated on the surface of graphite substrate (C) by plasma spraying process using a radio frequency inductively coupled plasma reactor. The coating was carried out by using 12- and 9-kW power under Ar atmosphere. The cross-section of coating layers and the surface were examined with SEM, EDX, XRD analysis and microhardness test. The thickness and quality of the coating increased with input power. Many pores were detected in the cross-sectional surface areas. Higher input power caused a better coating layer in NiTi alloy. The hardness of the coating layer decreases with higher input power.

Background/Objectives: Periodontitis (P), a chronic inflammatory condition that affects the supportive tissues around the teeth, is 3 to 4 times more prevalent in individuals with diabetes mellitus (DM), with a direct correlation between its severity and the levels of glycosylated haemoglobin (HbA1c). This study aimed to evaluate the periodontal clinical parameters following non-surgical periodontal treatment (NSPT) in patients with and without type 2 DM and P. Methods: Forty patients with P were divided into two groups: Group DM/P and Group P. All patients were assessed at baseline, and 90 and 180 days after receiving NSPT. The parameters evaluated included HbA1c levels, plaque index (PI), probing pocket depth (PPD), clinical attachment level (CAL), and bleeding on probing (BoP). Statistical analysis was performed with a significance level set at α = 5%. Results: There were significant differences in HbA1c levels between the DM/P and P groups at baseline, 90, and 180 days, as expected. Importantly, HbA1c levels did not change after NSPT. Group P showed a significant reduction in both PI and BoP values at 90 and 180 days (p &lt; 0.05). In contrast, group DM/P demonstrated a significant increase in the percentage of sites with PPD ≥ 5mm at 180 days (p &lt; 0.05). Additionally, group P exhibited an increase in sites with PPD ≤ 4mm and a decrease in sites with PPD ≥ 5mm at both 90 and 180 days (p &lt; 0.05). Conclusions: Our findings suggest that DM may compromise the effectiveness of NSPT, potentially hindering favorable outcomes during the follow-up period.

Epithelial ovarian cancer (EOC) has not significantly benefited from advances in immunotherapy, mainly because of the lack of well-defined actionable antigen targets. Using proteogenomic analyses of primary EOC tumors, we previously identified 91 aberrantly expressed tumor-specific antigens (TSAs) originating from unmutated genomic sequences. Most of these TSAs derive from non-exonic regions, and their expression results from cancer-specific epigenetic changes. The present study aimed to evaluate the immunogenicity of 48 TSAs selected according to two criteria: presentation by highly prevalent HLA allotypes and expression in a significant fraction of EOC tumors. Using targeted mass spectrometry analyses, we found that pulsing with synthetic TSA peptides leads to a high-level presentation on dendritic cells. TSA abundance correlated with the predicted binding affinity to the HLA allotype. We stimulated naïve CD8 T cells from healthy blood donors with TSA-pulsed dendritic cells and assessed their expansion with two assays: MHC-peptide tetramer staining and TCR Vβ CDR3 sequencing. We report that these TSAs can expand sizeable populations of CD8 T cells and, therefore, represent attractive targets for EOC immunotherapy.

Today with enhancement in technology, sciences, there is also an increase in global heating rate. There is an urgent need of any alternate efficient source to reduce the wastage of energy and to utilize it efficiently. The advanced preparation of Expanded graphite ,lauric acid, stearic acid as shape stabilized phase change material deals with different energy harvesting applications. The main reason behind the need for synthesis of this matrix is to prepare a material that can be used in low temperature energy storage applications. Mixture of lauric acid , stearic acid impregnated in expanded graphite through vacuum impregnation followed by Vacuum Drying and Microwave acid treatment serves as novel shape stabilized phase change material of its type. The microwave acid treatment was done in order to increase the removal of moisture from the sample thus initiating proper bonding of its constituents. The mixture was produced in 1:1:1 ratio where all expanded graphite, lauric acid , stearic acid has one proportions of each other. The product obtained after microwave acid treatment was subjected to SEM, DSC analysis

In recent experimental studies, we reported the aggravating effects of Asian sand dust (ASD) on male reproductive function in mice. However, the effects of fetal ASD exposure on male reproductive function have not been investigated. The present study investigated the effects of fetal ASD exposure on reproductive function in male offspring. Using pregnant CD-1 mice, ASD was administered intratracheally on days 7 and 14 of gestation, and the reproductive function of male offspring was determined at 5, 10, and 15 weeks after birth. The secondary sex ratio was significantly lower in the fetal ASD-exposed mice than in the controls. Histologic examination showed partial vacuolation of seminiferous tubules in immature mice. Moreover, daily sperm production (DSP) was significantly less in the fetal ASD-exposed mice than in the controls. DSP in the fetal ASD-exposed mice was approximately 10% less than the controls at both 5 and 10 weeks. However, both the histologic changes and the DSP decrease were reversed as the mice matured. These findings suggest that ASD exposure affects both the fetal development and the reproductive function of male offspring. In the future, it will be necessary to clarify the onset mechanisms of ASD-induced male fetus death and male reproductive disorders.

We fabricate paper-supported semiconducting devices by rubbing a layered molybdenum disulfide (MoS₂) crystal onto a piece of paper, similarly to the action of drawing/writing with a pencil on paper. We show that the abrasion between the MoS₂ crystal and the paper substrate efficiently exfoliates the crystals, breaking the weak van der Waals interlayer bonds and leading to the deposition of a film of interconnected MoS₂ platelets. Employing this simple method, that can be easily extended to other 2D materials, we fabricate MoS₂-on-paper broadband photodectectors with spectral sensitivity from the ultraviolet (UV) to the near-infrared (NIR). We also used these paper-based photodetectors to acquire pictures of objects by mounting the photodetectors in a homebuilt single-pixel camera setup.

In this paper we suggest a first ever construction of fractional integral and differential operators based on signed measures including a vector-valued case. The study focuses on constructing the fractional power of the Riemann-Stieltjes integral with a signed measure, using semigroup theory. The main result is a theorem that provides the exact form of a semigroup for the Riemann-Stieltjes integral with a measure having a countable number of extrema. The article provides examples of semigroups based on integral operators with signed measures and discusses the fractional powers of differential operators with partial derivatives.

Melt mixing is a convenient method to prepare polymer nanocomposites, but the extent of the dispersion of the solid filler reached is often limited, and may compromise the anticipated performance of these materials during service. Since the efficiency of extensional flows on dispersion is now well recognized, several mixers were designed with the aim of inducing both shear and extensional flow components. This work combines experimental and numerical data to better understand the kinetics of the dispersion of graphite nanoplates in a polypropylene melt, using a mixing device that consists of a series of stacked rings with equal outer diameter and alternating larger and smaller inner diameters, thus creating a series of converging/diverging flows. Numerical simulation of the flow using the opensource OpenFOAM software assuming both inelastic and viscoelastic responses predicted the velocity, streamlines, flow type and shear and normal stress fields for the mixer. Experimental and computed data were combined to determine the trade-off between the local degree of dispersion of the PP/GnP nanocomposite, measured as Area ratio, and the absolute average value of the hydrodynamic stresses multiplied by the local cumulative residence time. From considerations based on a theoretical approach to dispersion, the cohesive strength of the GnP agglomerates studied was estimated to be in the range 3 - 10kPa.

Graphite carbon nitride (g-C3N4) supported PtNi alloy nanoparticles (NPs) were fabricated via a facile and simple impregnation and chemical reduction method and explored their catalytic performance towards hydrogen evolution from ammonia borane (AB). Interestingly, the resultant Pt_0.5Ni₀.5/g-C₃N₄ catalyst affords superior performance, including 100% conversion, 100% H₂ selectivity, yielding the extraordinary initial total turnover frequency (TOF) of 250.8 mol_H2 min^-1 (mol_Pt)^-1 for hydrogen evolution from AB at 10 °C, a relatively low activation energy of 38.09 kJ mol⁻¹, and a remarkable reusability (at least 10 times), which surpass most of the noble metal heterogeneous catalysts. This notably improved activity is attributed to the charge interaction between PtNi NPs and g-C₃N₄ support. Especially, the nitrogen-containing functional groups on g-C₃N₄, serving as the anchoring sites for PtNi NPs, may be beneficial for becoming a uniform distribution and decreasing the particle size for the NPs. Our work not only provides a cost-effective route for constructing high-performance catalysts towards the hydrogen evolution of AB but also prompts the utilization of g-C₃N₄ in energy fields.

Heart failure is a prevalent cardiovascular condition with significant health implications, necessitating effective diagnostic strategies for timely intervention. This study explores the potential of continuous monitoring of non-invasive signals, specifically integrating Photoplethysmogram (PPG) and Electrocardiogram (ECG), for enhancing early detection and diagnosis of heart failure. Leveraging a dataset from the MIMIC-III database, encompassing 682 heart failure patients and 954 controls. Feature selection techniques were used to systematically select key features which were identified for their clinical relevance and significance in capturing cardiovascular dynamics and to reduce computational complexity and to decrease the chance of overfitting the ML algorithms. These features are then utilized to train and evaluate machine learning algorithms, resulting in a model with an impressive accuracy of 98%, sensitivity of 97.60%, specificity of 96.90%, and precision of 97.20%. The integrated approach outperforms single-signal strategies, showcas-ng its potential for early, precise, and non-invasive heart failure diagnosis. Furthermore, the study underscores the significance of continuous monitoring through wearables, emphasizing the benefits of integrating multiple signals for a comprehensive evaluation of cardiovascular health. The proposed approach holds promise for implementation in hardware systems to enable continuous monitoring, aiding in early detection and prevention of critical health conditions.

Non-isocyanate polyurethane synthesis by non-Sn catalysis is an essential challenge toward green polyurethane synthesis. Bismuth compounds are attractive candidates due to their low cost, low toxicity, and availability to urethane chemistry. We applied various Bi catalysts to the self-polycondensation of a bishydroxyurethane monomer and found BiCl3 to be an excellent catalyst through optimization. The catalytic activity and price of BiCl3 are comparable to those of Bu2SnO, while its toxicity is significantly low. BiCl3 is, therefore, a promising alternative to Sn-based catalysts in non-isocyanate polyurethane synthesis.

The aim of this randomized controlled clinical trial was to compare the 2-year clinical performance of resin composite restorations placed at non-caries cervical lesions (NCCL) with one-step self-etch, total-etch, and selective enamel etch & self-etch adhesive techniques. Thirty-two patients received three resin composite restorations each at NCCLs (Tetric EvoCeram/Ivoclar/Vivadent), bonded with a total-etch adhesive agent (ExciTE F/Ivoclar/Vivadent) and a self-etch (AdheSE One F/Ivoclar/Vivadent) without and with selective enamel etching. All restorations were evaluated by two examiners at baseline, 6-, 12-, 18- and 24-months post-operation regarding retention, caries occurrence, marginal adaptation, and marginal staining. A logistic regression analysis with generalized estimating equations was used. After 2 years, the retention rate was 86,8% for total-etch, 92.26% for self-etch, and 93.63% for selective enamel etching & self-etch. No caries were detected during all the restorations. Concerning marginal adaptation, the clinically perfect restorations were 26.9% for the total-etch technique, 16% for self-etch, and 25,9% for selective enamel etch & self-etch. All three adhesive strategies provided restorations with no significant differences in the retention rate and the marginal adaptation, whereas the total etch yielded better performance for marginal staining. All the restorations were assessed as clinically acceptable after 2 years.

The state-of-the-art smart city has been calling for an economic but efficient energy management over large-scale network, especially for the electric power system. It is a critical issue to monitor, analyze and control electric loads of all users in system. In this paper, we employ the popular computer vision techniques of AI to design a non-intrusive load monitoring method for smart electric energy management. First of all, we utilize both signal transforms (including wavelet transform and discrete Fourier transform) and Gramian Angular Field (GAF) methods to map one-dimensional current signals onto two-dimensional color feature images. Second, we propose to recognize all electric loads from color feature images using a deep neural network with multi-scale feature extraction and attention mechanism. Third, we design our method as a cloud-based, non-intrusive monitoring of all users, thereby saving energy cost during electric power system control. Experimental results on both public and our private datasets have demonstrated our method achieves superior performances than its peers, and thus supports efficient energy management over large-scale Internet of Things.

The electrical percolation of alternating current through two-phase polyethylene/graphite composite electrodes with different contents of graphite microparticles immersed in aqueous KCl solutions has been studied. Above the graphite content of the first percolation threshold, the electrochemical impedance response of this electrode is associated with an equivalent circuit of resistance Ru in series with a constant phase element CPE. An insulator material+conductive filler model is proposed in which the electroactive surface is considered as the intersection of the percolation cluster through the solid and the cluster associated with the interfacial region. CPE is analyzed assuming a distribution of micro-capacitors of the graphite particles in contact with the dielectric solution and inside the dielectric polymeric phase.

The ubiquitous deployment of Li-ion batteries (LIBs) in more demanding applications has reinforced the need to understand root-causes of thermal runaway. Herein we perform a forensic simulation of a real-case failure scenario, using localised heating of Li(Ni0.5Mn0.3Co0.2)O2 versus graphite 18650 cylindrical cells. This study determined the localised temperatures that would lead to venting and thermal runaway of these cells, as well as correlating the gases produced as a function of degradation pathway. Catastrophic failure, involving melting (with internal cell temperatures exceeding 1085°C), deformation and ejection of cell componentry, was induced by locally applying 200 °C and 250 °C to a fully charged cell. Conversely, catastrophic failure was not observed when the same temperatures were applied to the cells at lower state of charge (SOC). This work highlights the importance of SOC, chemistry and heat in driving the thermal failure mode of Ni-rich LIB cells, allowing for a better understanding of battery safety and associated design improvements.

Meat serves as a vital component of the human diet, offering a rich source of protein and essential trace elements. China stands as both a significant producer and consumer of meat on a global scale, leading the world in terms of total meat production and consumption. As the standard of living within the country continues to rise, there is a growing emphasis on the nutritional value and safety of meat consumption. The tenderness of meat is a critical factor influencing its overall quality. Traditionally, tenderness has been assessed through shear force testing, a method that is inherently destructive, inefficient, and results in considerable sample wastage. In light of these drawbacks, non-destructive testing techniques have emerged as a preferred alternative, promising greater accuracy, efficiency, and convenience without compromising the integrity of the samples. This paper delves into the application of five advanced non-destructive testing technologies in the realm of meat tenderness assessment. These include near-infrared spectroscopy, hyperspectral imaging, Raman spectroscopy, airflow optical fusion detection, and nuclear magnetic resonance detection. Each technology is scrutinized for its respective strengths and limitations, providing a comprehensive overview of their current utility and potential for future development. Moreover, the integration of these techniques with the latest advancements in artificial intelligence (AI) technology is explored. The fusion of AI with non-destructive testing offers a promising avenue for the development of more sophisticated, rapid, and intelligent systems for meat tenderness evaluation. This integration is anticipated to significantly enhance the efficiency and accuracy of quality assessment in the meat industry, ensuring a higher standard of safety and nutritional value for consumers. The paper concludes with a set of technical recommendations aimed at guiding the future direction of non-destructive, AI-enhanced meat tenderness detection, thereby contributing to the ongoing improvement of the meat industry in China and beyond.

The effect of the heterogeneity in sex factor is considered in the Markovian manpower modeling model. The estimation of the transition probability matrix of the staff flow was done using the maximum likelihood method. The expected future durations of the individuals in the manpower system were obtained under the aggregated and disaggregated (male and female) staff flow as well as their variances. Test for the heterogeneity of the staff based on sex factor was performed and the result of the heterogeneity test shows that there is difference between the disaggregated staff flows. The computed entrant probabilities also indicate that the male group has higher probabilities of attaining higher grades than the female group.

A new type of laminated flooring decorated by resin impregnated paper was designed, with the advantages of high stability, low deformation, natural and beautiful surface texture, comfortable foot feeling, low formaldehyde emission, improved flame retardant, high surface hardness and high wear resistance. The structure of this engineered wood flooring is based on the ordinary laminated flooring, followed by a decorative layer of thin wood pieces, and then the transparent improved flame retardant, wear-resistant paper is added to the top. After main influencing factors analysis, the surface unevenness was seriously affect the flame-retardant performance. The wear-resistant paper pressing technology commonly affects the decorative effect of laminated flooring. The hot-pressing temperature is the most important factor affecting the adhesion of resin impregnated. The optimal hot-pressing parameters are selected as the hot-pressing pressure of 3.5 MPa, hot-pressing temperature of 180 ℃, and hot-pressing time of 40 s. The new laminated flooring was improved with high flame retardant, high wear-resistant, combined with the conventional advantages of both solid wood composite flooring and reinforced wood flooring. The new laminated flooring decorated by resin impregnated paper has broad application prospects.

Background: Antibiofilm activity of silver nanoparticles has been extensively investigated in common bacteria. Metallo-β-lactamase producing Gram-negative bacteria are hard-to-treat microorganisms with few therapeutic options, and silver nanoparticles were not evaluated on the biofilm of these bacteria. Objectives: The aim of this study was to evaluate the antibiofilm activity of a bone scaffold impregnated with silver nanoparticles in NDM-producing Gram-negative bacilli. Methods: Bone scaffolds from bovine femur were used for the tests and impregnated with silver nanoparticles (50 nm) by physical adsorption. Silver nitrate minimal inhibitory and bactericidal concentrations (MIC and MBC) were performed on NDM-producing Escherichia coli, Klebsiella pneumoniae, and Pseudomonas aeruginosa. Disc diffusion tests for silver nanoparticles susceptibility and quantification of biofilm production on plate and bone with sessile cell count were performed. Results: The MIC results demonstrated that silver nitrate had an antimicrobial effect on all microorganisms, inactivating the growth of isolates from a concentration of 8 µg/mL. MBC results showed that E. coli 16.211 was the only isolate to present MIC different from MBC, with a value of 16 µg/mL. Conclusion: Bone scaffolds impregnated with silver nanoparticles can significantly reduce biofilm, and it can be a strategic material to be used as an implant for different approaches.

MicroRNAs (miRNA) exert regulatory actions via base-pairing with their binding sites on target mRNAs. Cooperative-binding, i.e., synergism, among binding sites on a mRNA is biochemically well-characterized. We studied whether this synergism is reflected in global relationship between miRNA-mediated regulatory activity and miRNA-binding-site count on the target mRNAs, i.e., leading to a non-linear relationship between the two. Recently, using our own and public datasets, we have enquired into miRNA regulatory actions: first, we analyzed the power-law distribution pattern of miRNA binding sites; second, strikingly, mRNAs for core miRNA regulatory apparatus proteins have extra-ordinarily high binding site counts, forming self-feedback-control loops; third, we revealed that tumor suppressor mRNAs generally have more sites than oncogene mRNAs; and fourth, we characterized enrichment of miRNA target mRNAs in translationally less-active polysomes relative to more-active polysomes. In these four studies, obvious correlation was observed qualitatively between the extent to which a mRNA is miRNA-regulated and its binding sites count. This paper summarizes the used datasets. We also re-analyzed the correlation by comparative linear and non-linear regression analyses. The results support a non-linear, instead of linear, relationship between the two parameters, conceivably a transcriptome-level reflection of cooperative-binding/synergism among miRNA binding sites on a target mRNA.

This paper presents a theory on graph topological structure and graph coloring, proving that for any N-order graph structure (with a topological structure similar to ), the maximum number of colors required for coloring is less than or equal to . The Four Color Theorem is just one special case of this theory, with the maximum structure size for a four-color graph being a 4-order structure graph, hence requiring only a maximum of 4 colors for coloring.

Glucose is a simple sugar molecule. The sugar molecule is chemically symbolised as C6H12O6. This means that the glucose molecule contains 6 carbon atoms (C), 12 hydrogen atoms (H) and 6 oxygen atoms (O). In human blood, the molecule glucose circulates as blood sugar. Normally after eating or drinking, our body breaks down the sugars in food and uses them to obtain energy for our cells. To do this, our pancreas produces insulin. Insulin "pulls" sugar from the blood and puts it into the cells for use. If someone has diabetes, their pancreas can't produce enough insulin. As a result, the level of glucose in the blood rises. This can lead one to many potential complications, including blindness, disease, nerve damage, amputation, stroke, heart attack and damage to blood vessels etc. In this study, a non-invasive method for monitoring blood glucose has been developed and is therefore easily usable. The device developed can measure the glucose level continuously and eliminates the disadvantages of the invasive system. Near-IR sensors (optical sensors) were used to estimate the concentration of glucose in the blood; these sensors have a wavelength of 940 nm. The sensor is placed on the tip of the finger and the output of the optical sensor is then connected to the microcontroller at the analogue input. Another sensor used, but only to provide more medical information was the heartbeat sensor. After processing and regression analysis, the glucose level is predicted, and data is sent via the Bluetooth network to a developed APP. The results of the implemented device were compared with available invasive methods. The study consists of a hardware platform inserted into an armband and then a small black parallelepiped-shaped box in which the optical sensors are inserted. The hardware consists of a microcontroller, a Near-IR optical sensor, a heartbeat sensor and a Bluetooth module.

Alzheimer's disease (AD) is a multifaceted neurodegenerative disorder characterized by cognitive decline and neuronal loss, representing a most challenging health issue. We present a computational analysis of transcriptomic data of AD tissues vs. healthy controls, focused on elucidation of functional roles played by long non-coding RNAs (lncRNAs) throughout the AD progression. We first assembled our own lncRNA transcripts from the raw RNA-Seq data generated from 527 samples of dorsolateral prefrontal cortex, resulting in the identification of 31,574 novel lncRNA genes. Based on co-expression analyses between mRNAs and lncRNAs, a co-expression network is constructed. Maximal subnetworks with dense connections are identified as functional clusters. Pathway enrichment analyses are conducted over mRNAs and lncRNAs in each cluster, which serve as the basis for the inference of functional roles played by lncRNAs involved in each of the key steps in an AD development model that we have previously build based on transcriptomic data of protein-encoding genes. Detailed information is presented about the functional roles by lncRNAs in activities related to stress response, reprogrammed metabolism, cell-polarity, and development. Our analyses have also revealed that lncRNAs have discerning power in distinguishing between AD samples of each stage and healthy controls. This study represents the first of its kind.

Non-toroidal shape primary pass through protection current transformers (CTs) are used to measure high currents. Their design provides them with a big airgap that allow passing several cables per phase though them, which is the main advantage versus toroidal types, as the number of CTs required to measure the whole phase current is drastically reduced. The cables pass through the transformer window can be in several positions. As the isolines of the magnetic field generated by the primary currents are centered in the cables, if these cables are not centered in the transformer window, the magnetic field will be non-uniform along the transformer core. Consequently, local saturations can appear if the cables are not properly disposed causing the malfunction of the CT. In this paper, the performance of a non-toroidal shape protection CT is studied. The research is focused on the cable position influence in possible partial saturations of the CT when it is operating near to its accuracy limit. Depending on the cable position, the ratio of the primary and secondary currents can depart from assigned ratio. The validation of this phenomenon has been carried out via Finite Element Analysis (FEA) showing that partial transformer core saturations appears in areas of the magnetic core close to the cable. Applying FEA, also the admissible accuracy region for cable positioning inside the CT is delimited. Finally, the simulation results are ratified with experimental tests performed in non-toroidal protection CTs varying the primary cables’ positions, which are subjected to currents up to 5 kA, achieving satisfactory results. From this analysis, installation recommendations are given.

A great deal of studies have assessed the expression of noncoding RNAs (ncRNAs) as well as their relevant molecular functions and biological mechanisms in the individuals of alcohol dependence. Alcohol dependence is one of the most prevalent neuropsychological disorders worldwide, and its pathogenesis is intricate and inadequately understood. There is considerable evidence demonstrating substantial links between multiple genetic factors and the development of alcohol dependence. Critical roles of ncRNAs have been emphasized in the pathophysiology of mental diseases including alcohol dependence. In the comprehension of ncRNAs action and their mechanisms of modification, they have emerged as therapeutic targets for a variety of psychiatric illness including alcohol dependence. Worth mentioning, dysregulated expression of ncRNAs has been regularly detected in individuals of alcohol dependence. An in-depth knowledge of roles of ncRNAs and m6A modification may be valuable for the development of a novel treatment against alcohol dependence. In general, a deeper comprehension of functional roles ncRNAs may make significant contributions to the precise diagnosis and/or actual treatment of alcohol dependence. Here in this review, we mostly focused on the up-to-date knowledge regarding alterations and/or modifications in the expression of ncRNAs in alcohol dependence, and then, presented their prospects for future research and therapeutic application with a novel concept of engram-system.

To date, the percentage composition of the lung microbiome in bronchopulmonary cancer has not been summarized. Existing studies on identifying the lung microbiome in bronchopulmonary cancer through 16S rRNA sequencing have shown variable results regarding the abundance of bacterial taxa. Objectives: To identify the predominant bacteria in the lung microbiome of bronchopulmonary cancer from samples collected through bronchoalveolar lavage and to assess their potential role in the diagnosis of bronchopulmonary cancers. Data Sources: A systematic review of English articles using MEDLINE, Embase, and Web of Science. Search terms included lung microbiome, lung cancer, bronchoalveolar lavage. Study Selection: Randomized clinical trials that investigated the lung microbiome in bronchopulmonary cancer with samples collected via bronchoalveolar lavage. Data Extraction: Independent extraction of articles using predefined data fields, including study quality indicators. Data Synthesis: Nine studies met the inclusion criteria, focusing on those that utilized a percentage expression of the microbiome at the phylum or genus level. There was noted heterogeneity between studies, both in terms of phylum and genus, with a relatively constant percentage of the Firmicutes phylum and the genera Streptococcus and Veillonella being mentioned. Significant differences were also observed regarding the inclusion criteria for study participants, the method of sample collection, and data processing. Conclusions: To date, there is no consistent percentage pattern at the phylum or genus level in bronchopulmonary cancer, with the predominance of a phylum or genus varying across different patient cohorts, resulting in non-overlapping outcomes.

Background Sarcopenia is a state with progressive and generalized loss of skeletal muscle mass and strength. It is a serious complication occurring in chronic kidney disease (CKD) patients which increases morbidity and mortality rate. Sarcopenia is diagnosed when loss of both compartments - muscle strength and skeletal muscle quality or quantity are present. However, there are still numerous patients, also with CKD, diagnosed as pre-sarcopenic individuals with low muscle strength and normal skeletal muscle quality or quantity and conversely, with correct muscle strength and decreased skeletal muscle mass, who are prone to develop sarcopenia in future life. It is crucial to examine numerous variables possibly associated with changes of skeletal muscle mass and muscle strength in terms of preventing the development of sarcopenia. The aim of the study was to investigate anthropometric and clinical correlates and sources of variation in both skeletal muscle mass and muscle strength in advanced stages of CKD. Methods The study sample consisted of 84 non-dialysis dependent patients of both sexes (including 45.2% of women) with eGFR < 45 ml/min/1.73m²: 26.2% with eGFR 30-44 mL/min/1.73 m², 65.5% with eGFR 15-29 mL/min/1.73 m² and 8.3% with eGFR < 15 mL/min/1.73 m². Muscle strength was estimated by measuring hand grip strength (HGS) with the use of handheld hydraulic dynamometer. Muscle quantity was measured by bioimpedance spectroscopy using Body Composition Monitor. Appendicular skeletal muscle mass (ASM) was calculated according to Lin’s formula. Serum creatinine, urea, uric acid and albumin were measured. Results In bivariate analysis we found that ASM significantly and positively correlated with anthropometric variables such as body mass (r=0.903, p<0.001), NH weight (r=0.882, p<0.001), height (r=0.694, p<0.001), body mass index (BMI) (r=0.701, p<0.001), lean tissue mass (LTM) (r=0.664, p<0.001), lean tissue index (LTI) (r=0.433, p<0.001), fat mass (r=0.614, p<0.001) and fat tissue index (FTI) (r=0.449, p<0.001), and was negatively associated with clinical variable such as hydration status (p<0.001). HGS significantly and positively correlated with anthropometric parameters such as body mass (r=0.319, p=0.003), NH weight (r=0.315, p=0.004), height (r=0.666, p<0.001), LTM (r=0.490, p<0.001), LTI (r=0.238, p=0.029), and ASM (r=0.501, p<0.001), and was negatively associated with clinical variables like uric acid (p=0.039) and urea (p<0.001). After adjustment for age, sex and height, HGS remained significantly and negatively related with uric acid (β=-1.078, p=0.041) and hydration status (β=-0.805, p=0.042). Conclusions In CKD patients, ASM is determined mainly by anthropometric parameters but HGS - both by anthropometric and clinical variables specific for CKD.

The economics and safety of reactors can be affected by the diffusion of fission products into graphite. Xenon (Xe) fission products diffusing into the graphite is the most critical neutron absorber and poison that can slow down or stop the chain reaction. The transport parameters for inhibiting the xenon diffusion in graphite are therefore the utmost scientific problem. Self-sintered nanopore-isotropic (~ 40nm) graphite (SSNG) derived from green pitch coke can decrease Xe diffusion into the graphite. In this study, a method for measurement of diffusion coefficients of fission products diffusion in graphite by Rutherford backscattering spectrometry (RBS) was reported. The SSNG substrates were implanted with Xe at a dose of 4.8×1015 ions/cm2 and energy of 7 MeV. The RT-implanted samples were annealed in a vacuum at 650°C for 9 h. The implanted and annealed samples were characterized by RBS. The diffusion coefficient D(Xe,650°C) is 6.49×10-20 m2/s. The results indicate the excellent ability to inhibit Xe diffusion of the SSNG and present significance in designing and evaluating the safety of nuclear reactors.

Using analysis methods such as Rutherford backscattering Spectrometry, scanning electron microscopy, X-ray diffraction, and Raman spectroscopy, the diffusion behavior of iodine in micro/nano-porous graphite under high-temperature conditions was studied. The results indicate that iodine diffusion leads to the contraction of graphite microcrystals, a decrease in interlayer spacing, and an increase in defect density, resulting in a reduction in microcrystal size. Upon diffusion of iodine out of iodine-loaded graphite, the microcrystal size of the graphite increases, the interlayer spacing appears to return to the initial state, and the defect density decreases. By comparing the iodine diffusion performance of nanoporous graphite G400 and G450 with microporous graphite G500, it was determined that nanoporous graphite exhibits better inhibition of iodine diffusion compared to microporous graphite. Studying the diffusion behavior of iodine in micro/nano-porous graphite has significant academic significance and engineering value for the screening, design, and performance optimization of nuclear graphite.

Development of carbon nanomaterials for adsorption thus removal of organic pollutants from water is a progressive research subject. In this regard, carbon nanomaterials with bifunctionality towards polar and non-polar or even amphiphilic undesired materials is indeed attractive for further study and implementation. Here, we created carbon buckypaper adsorbents comprising amphiphilic (oxygenated amorphous carbon (a-COx)/graphite (G)) nanofilaments that can dynamically adsorb organic biomolecules (i.e. urease enzyme) and thus purify the wastewaters of relevant industries. Given the dynamic conditions of the test, the adsorbent was highly efficient in adsorption of the enzyme (88%) while permeable to water (2382 L.h-1.m-2), thus holds a great promise for further development and upscaling. A subsequent citric acid functionalization declined selectivity of the membrane to urease, implying the biomolecules adsorb mostly via graphitic domains rather than oxidized, polar amorphous carbon ones. The devised platform i.e. the urease functionalized buckypaper is optimally conductive (13 S.cm-1) and can be further employed as a biosensor. Accordingly, water treatment can be linked to biosensing via a nanostructured membrane.

A rehabilitation technique for asphalt pavements with geosynthetic is the application of impregnated nonwoven geotextiles between deteriorated and new asphalt overlays. The performance investigation of impregnated geotextiles proves that they are enhancing in mechanical and hydraulic properties. Although, the installation process may cause severe impacts on these materials’ performance. During the installation, the geotextile suffers damage due to the traffic of high load vehicles, as compactors and pavers, and the friction with granular materials found under its layer or poured above it. This paper aims to investigate how the damage caused by granular materials on nonwoven geotextiles impregnated with different asphalt emulsions effect on their strength resistance and permittivity. From two types of nonwoven geotextiles: polypropylene and polyethylene terephthalate, the comparison uses geotextiles in three conditions: not impregnated, impregnated with asphalt emulsion of rapid setting, and impregnated with asphalt emulsion changed by an elastomeric polymer. Part of the samples followed the damage according to ISO 10722 procedure, placed between three different scenarios of granular materials, applying gravel, sand, and clay. After the damage process, the samples were submitted to mechanical and hydraulic properties evaluations.

This paper addresses the evolving landscape of electricity markets in Europe, with a focus on the integration of Renewable Energy Communities as introduced by the Renewable Energy Directive 2018/2001. Residents within a postal code area are highly incentivized to join a community, which enables them to exchange energy among themselves at lower procurement costs. Thereby, energy management systems optimize the operation of respective energy systems, with electrical load forecasting playing a key role. Given that prosumers may switch between communities on a daily basis, electricity demands within these groups will vary, leading to data that is non-stationary, discontinuous as well as non-identical and independently distributed. To encounter this issue, we propose a sophisticated forecasting model that applies federated learning, using informations from various distributed communities to learn domain-invariant features. To achieve this, we initially utilize synthetic electrical load time series at district level and aggregate them to profiles of Renewable Energy Communities with dynamic portfolios. Subsequently, we develop a forecasting model that accounts for the composition of residents of a Renewable Energy Community, adapt data pre-processing in accordance with the time series process, and detail a federated learning algorithm that incorporates weight averaging and data sharing. Following the training of various experimental setups, we ultimately evaluate their effectiveness. The findings suggest that our proposed framework is capable of effectively forecast non-stationary and discontinuous time series and that it can be applied to new, unseen data through the integration of knowledge from multiple sources.

In recent years, extensive research has been conducted on the IoT, one of its challenges has been the field security and penetration in these networks. security solutions it Require more planning and awareness to ensure system security and privacy protection.it has also been shown that adjusting the weights of neural networks can help improve the accuracy of detection to what extent. the challenge in the attack detection field is to increase the accuracy of attack detection by machine learning methods, in this paper, a new method is presented to adjust weights of the random neural network for attack detection. Evaluations of the proposed method show that compared to random neural network methods, nearest neighbor, and support vector machine, the accuracy of attack detection improves up to 99.49 percent, and the random neural network method has been able to improve by 99.01 percent, placing the best methods together in these experiments in the form of a multi-learning model showed that the results also had an increase in accuracy up to 99.56 percent, while the training time in the proposed model is less compared to the random neural network method.

Background and Aims: Obesity is a pervasive health issue in children. It affects multiple systems in the body including the gastrointestinal tract. Research on obesity-related gastrointestinal diseases has focused mostly on hepatobiliary disorders. However, non-hepatic gastrointestinal diseases such as gastroesophageal reflux, constipation, and functional abdominal pain, though common and debilitating, have not been highlighted in the context of obesity. These entities can downgrade the already compromised lifestyle of obese children. Some of these disorders are more difficult to treat in these children compared to their peers with normal body mass index. Method: We reviewed the available literature on the association between obesity and these three common gastrointestinal disorders. Results: - There appears to be a strong correlation between childhood obesity and constipation and gastroesophageal reflux, and a probable correlation with functional abdominal pain. Conclusion: We suggest that given the available literature, weight management should be an integral part of the management of gastroesophageal reflux, constipation, and functional abdominal pain in obese children. This gains relevance especially because of the recent availability of medications for the treatment of obesity in children.

This study introduces a novel approach by proposing a dressing impregnated with vancomycin and chlorhexidine for postoperative care, specifically targeting patients undergoing orthopedic surgeries. The research design involved a pilot study with a randomized control group, aiming to evaluate the vancomycin with chlorhexidine dressing's efficacy and safety. A total of 12 patients used impregnated dressing and 9 used the same dressing without impregnation. Despite limitations, including the small sample size and single-center study location, our findings demonstrate the safety of the impregnated dressing in trauma surgeries, indicating potential applicability in broader surgical contexts. In conclusion, this study contributes to the discourse on preventive strategies for SSIs, presenting a pioneering approach with the vancomycin and chlorhexidine-impregnated dressing. Future research endeavors, incorporating larger-scale studies and addressing study limitations, are crucial for advancing the understanding and implementation of effective postoperative care strategies.

We discuss the electrodeposition of two-dimensional (2D) Pt-nanostructures on HOPG achieved under constant applied potential versus a Pt counter electrode (Eappl = ca. - 2.2 V vs RHE). The deposition conditions are discussed in terms of the electrochemical behavior of the electrodeposition precursor (H2PtCl6). We performed cyclic voltammetry (CV) of the electrochemical Pt deposit on HOPG and on Pt substrates to study the relevant phenomena that affect the morphology of Pt deposition. Under conditions where the Pt deposition occurs and H2 evolution is occurring at the diffusion-limited rate (- 0.3 V vs RHE), Pt forms larger structures on the surface of HOPG, and the electrodeposition of Pt is not limited by diffusion. This indicates the need for large overpotentials to direct the 2D growth of Pt. Investigation of the possible effect of Cl- showed that Cl- deposits on the surface of Pt at low overpotentials, but strips from the surface at potentials more positive than the electrodeposition potential. The CV of Pt on HOPG is a strong function of the nature of the surface. We propose that during immersion of HOPG in the electrodeposition solution (3 mM H2PtCl6, 0.5 M NaCl, pH 2.3) Pt islands are formed spontaneously, and these islands drive the growth of the 2D nanostructures.

(1) Background: Intravesical Chemotherapy is standard of care in intermediate risk non-muscle-invasive bladder cancer (NMIBC). Different agents are used across the world based on availability, cost and practice patterns. Epirubicin (EPI), one of these agents is used by many centers over many decades. However, its true differential efficacy compared to other agents and its tolerability is still poorly reported. We aimed to assess the differential efficacy and safety of intravesical EPI in NMIBC patients. (2) Methods: A systematic search of PUBMED, Webofscience, clinicaltrials.gov, and Google Scholar databases was performed on December 31, 2023. We reviewed 28 studies that included patients treated EPI after TURBT (transurethral resection of bladder tumors) for NMIBC and who compared oncological outcomes such as recurrence and progression to other adjuvant treatment such as Mitomycin C (MMC), Gemcitabine (GEM) and BCG. Further, we looked at the safety profile of EPI at room temperature under hyperthermia intravesically and at the oncological outcomes when administrated with hyperthermia; (3) Results: When compared to other chemotherapeutics (MMC/GEM), EPI seemed to be equally effective; however, EPI seems less effective in preventing disease management recurrence compared to BCG intravesical. The most common adverse events of EPI include cystitis, dysuria, and pollakiuria. (4) Conclusions: EPI exhibits similar oncological performances to Gemcitabine and Mitomycin C currently used for adjuvant therapy in NMIBC. Novel delivery mechanisms such as hyperthermia are promising newcomers.

Cystic artery bleeding (CAB), a relatively uncommon entity, can arise from both traumatic and non-traumatic etiologies. This pictorial essay aims to elucidate the computed tomography (CT) findings associated with CAB in these distinct contexts. In traumatic CAB, particularly blunt or penetrating trauma, a cystic artery lesion is the culprit behind the hemoperitoneum characteristically located within the gallbladder fossa. Prompt diagnosis is crucial. Fortunately, trans-arterial embolization offers a successful treatment option for traumatic cystic artery lesions, especially in settings where non-operative management is preferred. Non-traumatic CAB, on the other hand, often stems from inflammation in the hepatobiliary and pancreatic system, gallbladder tumours, or iatrogenic injuries. The underlying mechanism typically involves cystic artery wall damage, either due to inflammation or procedural complications, leading to the formation of a cystic artery pseudoaneurysm (CAP). Notably, CAP bleeding can manifest long after the causative event, posing a diagnostic challenge with a variable clinical presentation. This pictorial essay serves to illustrate the CT signs and features of CAB in both traumatic and non-traumatic scenarios. Additionally, it will delve into the characteristic CT appearance of CAP.

Lung involvement in rheumatic diseases is a major determinant of patient morbidity and mortality; however, its diagnosis depends on the detection methods used. We compared the incidence of pulmonary involvement in newly diagnosed treatment-naive patients with rheumatic diseases, as assessed by pulmonary function tests (PFTs) and chest high-resolution computed tomography (HRCT). This retrospective study reviewed the symptoms, spirometry results, and HRCT scans of 22 newly diagnosed, treatment-naïve patients and age-matched controls from the University General Hospital “Attikon”, Athens, Greece, between January 2021 and December 2023. Correlations between clinical findings and spirometry parameters were tested. HRCT scans revealed lung abnormalities in all patients, including peribronchial wall thickening (61.5%), ground glass opacities (59.1%), parenchymal bands (54.5%), air-trapping (50%), reticular patterns (45.5%), bronchiectatic changes (40.9%), and parenchymal opacities (31.8%). PFTs, performed in 17/22 (77.3%) patients, revealed definite pathology in 5 patients (restrictive: N=4; obstructive: N=1). No association was found between spirometric indices and clinical parameters. The results indicate a higher prevalence of abnormal chest CT than of PFT abnormalities, suggesting that HRCT is more sensitive in detecting early lung involvement in pediatric patients with rheumatic disease and should be considered in the routine evaluation of these patients.

As technology advances, the field of electrical and computer engineering continuously demands the introduction of innovative new tools and methodologies to facilitate effective learning and comprehension of fundamental concepts. This research addresses an identified gap in technology-augmented education capabilities and researches the integration of Virtual Reality (VR) technology with real-time electronic circuit simulation to enable and enhance the visualization of non-observable concepts such as voltage distribution and current flow within these circuits. In this paper, we describe the development of our immersive educational platform, which makes understanding these abstract concepts intuitive and engaging. This research also involved the design and development of a VR-based circuit simulation environment. By leveraging VR’s immersive capabilities, our system enables users to physically interact with electronic components, observe the flow of electrical signals, and manipulate circuit parameters in real-time. Through this immersive experience, learners can gain a deeper understanding of fundamental electronic principles, transcending the limitations of traditional two-dimensional diagrams and equations. Furthermore, this research focuses on the implementation of advanced and novel visualization techniques within the VR environment for non-observable electrical and electromagnetic properties, providing users with a clearer and more intuitive understanding of electrical circuit concepts. Examples include color-coded pathways for current flow and dynamic voltage gradient visualization. Additionally, real-time data representation and graphical overlays are researched and integrated to offer users insights into the dynamic behavior of circuits, allowing for better analysis and troubleshooting.

Europium is one of the most reactive lanthanides and humans use it in many different applica-tions, but we still know little about its potential toxicity and cellular response to its exposure. Two strains of the eukaryotic microorganism model Tetrahymena thermophila adapted to high concentrations of two Eu(III) compounds (EuCl3 or Eu2O3) were obtained and compared to a control strain and cultures treated with both compounds. In this ciliate, EuCl3 is more toxic than Eu2O3. LC50 values show that this microorganism is more resistant to these Eu(III) compounds than other microorganisms. Oxidative stress originated mainly by Eu2O3 is minimized by overexpression of genes encoding important antioxidant enzymes. The overexpression of metallothionein genes under treatment with Eu(III) compounds supports the possibility that this lanthanide may interact with the -SH groups of the cysteine residues from metallothi-oneins and/or displace essential cations of these proteins during their homeostasis function. Both lipid metabolism (lipid droplets that fuse with europium-containing vacuoles) and au-tophagy are involved in the cellular response to europium stress. Bioaccumulation, together with a possible biomineralization to europium phosphate, seems to be the main mechanism of Eu(III) detoxification in these cells.

Enhancing spectral efficiency, especially in Non-line-of-Sight environments, is emerging as a pivotal necessity when dealing with the evolving landscape of 5G networks and beyond, sur-passing the capabilities of previous 4G systems to achieve a high information rate combined with minimal interference. Contrary to depending on the traditional Orthogonal Multiple Access (OMA) systems to tackle the issues caused by Non-line-of-Sight (NLoS) environments, advanced wireless networks are focusing on adopting innovative models such as Non-Orthogonal Multiple Access (NOMA), MIMO, IRS technology, etc. In this paper, we present technologies that can be integrated with NOMA to enhance communication reliability in environments that suffer from issues such as limited coverage and lower spectral efficiency mainly caused by huge obstacles. Our exploration includes the fundamental concepts of Cooperative NOMA (C-NOMA), Multiple Input Multiple Output (MIMO), Intelligent Reflective Surfaces (IRS), Unmanned Aerial Vehicles (UAVs), and Energy Harvesting (HV), which adds a layer of sophistication, promising not only improved connectivity but also contributing to a more reliable and environmentally friendly data trans-mission landscape.

Alzheimer's disease (AD) is the most prevalent form of dementia. With the global aging population, the incidence of AD and related dementias is projected to rise dramatically, posing significant public health challenges. Traditionally, the diagnosis of AD has relied on the detection of amyloid-beta (Aβ) plaques and neurofibrillary tangles of hyperphosphorylated tau in the brain, assessed through invasive cerebrospinal fluid (CSF) analysis and costly positron emission tomography scans. However, these methods are not feasible for widespread screening or use in low-resource settings. Recent advances in blood-based biomarkers offer a promising alternative for the early detection and monitoring of AD. These biomarkers provide a minimally invasive, cost-effective means of tracking the pathological progression of AD before the onset of clinical symptoms, potentially enabling earlier and more accurate diagnosis. Blood-based biomarkers, including those related to Aβ, phosphorylated tau, and neurofilament light polypeptide, have demonstrated significant potential in reflecting the underlying neuropathology of AD and correlating with traditional CSF and imaging biomarkers. This review synthesizes the latest research on blood-based biomarkers in AD, highlighting their role in the disease's etiopathogenesis, diagnostic accuracy, and prognostic value. We discuss the emerging evidence on proteinopathies, neuroinflammation, vascular pathology, and bioenergetic profiles, emphasizing the clinical applicability of these biomarkers. Furthermore, we explore the integration of blood-based biomarkers with advanced neuroimaging techniques and their potential to revolutionize the diagnostic landscape of AD, particularly in resource-limited settings. We have integrated protein-protein interaction (PPI) and miRNA network analyses to enhance the analysis. By incorporating these, we can explore the interactions and relationships between different proteomic, genomic, and epigenomic biomarkers, potentially unveiling new insights into the underlying biological mechanisms of AD. The continued development and validation of these biomarkers could lead to more accessible and equitable AD diagnostics, ultimately improving patient outcomes.

Recent analyses of cosmic microwave background surveys have revealed hints that there may be a non-trivial running of the running of the spectral index. If future experiments were to confirm these hints, it would prove a powerful discriminator of inflationary models, ruling out simple single field models. We discuss how isocurvature perturbations in multi-field models can be invoked to generate large runnings in a non-standard hierarchy, and find that a minimal model capable of practically realising this would be a two-field model with a non-canonical kinetic structure. We also consider alternative scenarios such as variable speed of light models and canonical quantum gravity effects and their implications for runnings of the spectral index.

Neurosteroids are pleiotropic molecules involved in various neurodegenerative diseases with neuroinflammation. We assessed neurosteroids serum levels in a cohort of Parkinson’s Disease (PD) patients with heterozygous glucocerebrosidase (GBA) mutations (GBA-PD) compared with matched cohorts of consecutive non-mutated PD (NM-PD) patients, and healthy subjects with (GBA-C) and without (NM-HC) GBA mutations. A consecutive cohort of GBA-PD was paired for age, sex, disease duration, Hoehn &amp; Yahr stage, and comorbidities with a cohort of consecutive NM-PD. Two cohorts of GBA-C and HC were also considered. Clinical assessment included the MDS-UPDRS and the Montreal Cognitive Assessment (MoCA). Serum samples were processed and analyzed by liquid chromatography coupled with triple quadrupole mass spectrometry. Twenty-two GBA-PD (males: 11, age: 63.68), 22 NM-PD (males: 11, age: 63.05), 14 GBA-C (males: 8; age: 49.36), and 15 HC (males: 4; age: 60.60) were studied. Compared to NM-PD, GBA-PD showed more hallucinations and psychosis (p&lt;0.05, Fisher’s exact test) and higher MDS-UPDRS part-II (p&lt;0.05). Most of the serum neurosteroids were reduced in both GBA-PD and NM-PD compared to the respective control cohorts, except for 5α-DHP. Allopregnanolone was the only neurosteroid significantly lower (p&lt;0.01, Dunn’s test) in NM-PD compared to GBA-PD patients. Only in GBA-PD, allopregnanolone, and pregnanolone levels correlated (Spearman) with a more severe MDS-UPDRS part-III. Allopregnanolone levels also negatively correlated with MoCA scores, and pregnanolone levels correlated with more pronounced bradykinesia. This pilot study provides the first observation of changes in neurosteroid peripheral levels in GBA-PD. The involvement of the observed changes in the development of neuropsychological and motor symptoms of GBA-PD deserves further attention.

Recently Kawashima has reported that, when wetted with alkanes, several forms of graphite and single-layer graphene exhibit superconductor-like properties above room temperature under ambient pressure [AIP Adv. 2013, 3, 052132; arXiv:1612.05294; arXiv:1801.09376]. Under the assumption that these seemingly unlikely properties arise from the presence of paired electrons brought about by the alkane-wetting, we explored their implications to arrive at a probable mechanism for strong electron-pairing driven by Fermi surface nesting and acoustic phonon. This mechanism explains why alkane-wetting is essential for the graphene systems to become “superconductor-like” above room temperature and why the “T_c” of alkane-wetted pitch-based graphite fibers increases almost linearly from ~363 to ~504 K with increasing the molecular weight of alkane from heptane to hexadecane. It also provides a number of experimentally-verifiable predictions, the confirmation of which will provide a strong support for the superconductivity driven by Fermi surface nesting and acoustic phonon.

In order to solve the problem of large eddy current loss and high temperature rise caused by large amount of permanent magnet, a new type of combined magnetic pole permanent magnet motor is proposed in this paper. The sinusoidal distribution subdomain model of non-uniform air gap rotor is established by using Laplace equation, and the analytical expression of eddy current loss of rotor in uniform air-gap and non-uniform air-gap is derived. The effect of rotor eccentricity on eddy current loss is obtained. According to the characteristics of distributed winding of non-uniform air gap combined pole permanent magnet motor, equivalent treatment is performed to obtain the equivalent thermal conductivity, so as to establish equivalent thermal network model of motor, calculate the temperature value of each component of the motor, and verify the correctness of the thermal network model through the method of magnetothermal bidirectional coupling. Finally, an experimental platform is set up to carry out temperature rise experiments on the two prototypes respectively. Experimental results show that the non-uniform air-gap rotor structure can effectively reduce the rotor eddy current loss and motor temperature rise, and also verify the accuracy of the analytical model calculation results.

Microgrid (MG) control is essential for efficient, reliable, and sustainable energy management in distributed energy systems. Genetic Algorithm-based energy management systems (GA-EMS) can optimally control a MG by finding global optima and handling complex, non-linear, and non-convex problems, but they can be computationally intensive, making real-time control challenging. Model Predictive Control (MPC)-based EMS predicts future behaviour over a defined horizon, ensuring optimal performance and constraint satisfaction but typically relies on linear models. This paper proposes a novel Genetic Predictive Control (GPC) method, combining GA and MPC to enhance resource allocation, balance multiple objectives, and adapt dynamically to changing conditions. Integrating GA with MPC significantly improves the handling of non-linearities and non-convexity in the system model, leading to more accurate and effective control. Comparative analysis shows that GPC significantly reduces excess power production—surplus power generated beyond load demand—improving resource allocation efficiency. For instance, in the Mutation–Random Selection scenario, GPC reduced excess power to 76.0W compared to 87.0W with GA. Additionally, GPC balances cost, emissions, and power efficiency. In the Crossover-Elitism scenario, GPC achieved a daily cost of $113.94 compared to GA's $127.80, and carbon emissions of 52.83 kg CO2e compared to GA's 69.71 kg CO2e, demonstrating GPC's cost efficiency and environmental benefits. While MPC optimizes a weighted sum of objectives, designing appropriate weights can be challenging and may result in non-convex problems. GA handles multiple, conflicting objectives through multi-objective optimization, providing Pareto-optimal solutions. GPC's dynamic adaptability maintains optimal performance by forecasting future load demands and adjusting control actions. GPC consistently achieves lower emissions than GA across various scenarios and, although it sometimes incurs higher costs, such as $113.94 compared to $131.90 in the Crossover–Random Selection scenario, its holistic approach balances these costs with other metrics, making it cost-effective in the long run. By reducing excess power production and emissions, GPC contributes to economic savings and promotes sustainable practices. These findings underscore GPC's potential as a versatile, efficient, and environmentally beneficial optimization tool for power generation systems.

This article aims to analyze the relationship between non-obstructive coronary artery disease (NOCAD) and atrial fibrillation (AF), exploring the underlying pathophysiological mechanisms and implications for clinical management. NOCAD and AF are prevalent cardiovascular conditions that often coexist, yet their interrelation is not well understood. NOCAD, characterized by the presence of atherosclerotic plaques without significant luminal stenosis, can lead to ischemic necrosis of cardiomyocytes and their replacement with fibrous tissue, in this way sustaining the focal ectopic activity in atrial myocardium. Atrial fibrillation, on the other hand, is the most common sustained cardiac arrhythmia, associated with an increased risk of stroke and heart failure, which may accelerate atherosclerosis and may increase oxygen consumption in the myocardium, creating a mismatch between supply and demand, thus promoting the development or worsening of coronary ischemia. Therefore, NOCAD and AF seems to be a complex Interplay with one begets another.

The present study sought to determine the effect of incorporating a Chitosan-TiO2 nano-composite on the color stability of pigmented Room Temperature Vulcanization (RTV) maxillofacial silicone subjected to a variety of accelerated aging conditions. The experimental setup consisted of one hundred groups of five disk-shaped specimens (22mm diameter, 2mm thick) each, created using RTV silicon elastomer type A-2186, with the total sample distributed into four groups based on the pigments combined with the silicon—specifically, brilliant red, blue, and yellow dry intrinsic pigments (at 0.2% concentration by weight) and a fourth group that remained non-pigmented. Each of these primary groups was further subdivided into five categories corresponding to the silicon variants treated with different nanoparticles—2% TiO2, 3% Chitosan, a hybrid nano-combination of 1% TiO2/Chitosan, 1% synthesized Chitosan-TiO2 Nanocomposite, and a control group devoid of nanoparticle additions. The synthesized Chitosan-TiO2 Nanocomposite was effectively prepared using the core-shell method. The color stability of each silicon category, irrespective of whether pigmented or non-pigmented was evaluated by calculating the color difference (ΔE) pre- and post-subjection to five distinct accelerated aging conditions: 30 hours in an antibacterial cleaning solution, six months in sebum, six months in sweat, UV-accelerated aging for 720 hours, and outdoor weathering for six months. Color measurements were taken using a Colorimeter within the CIELAB color system. Statistical analyses, including one-way ANOVA at a significance level of p < 0.05, were employed to discern significant differences among the various accelerated aging conditions across the five silicon categories. Further comparisons were made using Dennett's T3 multiple comparison test, Tukey HSD multiple comparisons, and a t-test, with SPSS for Windows version 27.0 as the software platform. Results indicated that all silicon types, whether pigmented or not, exhibited varying degrees of color change under different aging conditions. Red-colored samples, across all silicon categories, demonstrated significant color alterations after 720 hours of UV-accelerated aging, with the most pronounced change in the 3% Chitosan samples and the least in the 2% TiO2 samples. Six months of outdoor weathering led to a marked increase in ΔE values across all categories. The blue-pigmented silicon samples treated with 2% TiO2 showed the highest color modification, while the yellow-pigmented silicon and non-pigmented silicon also underwent significant color shifts, particularly in the control and Chitosan-TiO2 categories, respectively. The study underscores the pervasive influence of outdoor weathering on color stability across all silicon categories. It also demonstrates that while nanoparticle incorporation offers some resilience against accelerated aging, it fails to provide adequate protection against the specific effects of UV radiation encountered during outdoor weathering.

Dental agenesis is one of the most common developmental anomaly in humans and it is frequently as-sociated with several other oral abnormalities. The present case describes nonfamilial agenesis of per-manent teeth in a twenty-one-year-old boy, with no apparent systemic abnormalities. The treatment in-cluded a personalized and interdisciplinary approach by the means of endodontics, orthodontics, im-plants supported restorations and prosthetic treatments. The treatment plan was thoroughly elaborated using photographic analysis, study models, orthopantomogram, CBCT and cephalograms. Virtual smile design, diagnostic waxing, and mock-up previsualized the treatment objectives. The edentulous spaces were reconstructed by inserting dental implants, and monolithic Zirconia implant supported restorations. The final results showed a highly aesthetic and functional rehabilitation. Periodic checkups have shown that the stability of the result is well maintained and that the implant supported restorations are an op-timal solution for patients with multiple anodontia.

Vascular endothelial growth factor (VEGF) and its receptors (VEGFRs) serve an essential role in tumor angiogenesis and have emerged as potential therapeutic targets in lung cancer. This review explores the significance of serum VEGF levels as a predictive biomarker in non-small cell lung cancer (NSCLC). The VEGF family, consisting of VEGFA, VEGFB, VEGFC, VEGFD, and placenta growth factor (PlGF), engages with specific receptors, including tyrosine kinase receptors (VEGFR-1, VEGFR-2, and VEGFR-3) and neuropilin receptors (NRP-1 and NRP-2), to promote angiogenesis and lymphangiogenesis. VEGF-A, the primary component of the VEGF family, binds to VEGFR-2 to stimulate endothelial cell proliferation and migration, while VEGF-B, VEGF-C, and VEGF-D interact with VEGFR-1 and VEGFR-3 to regulate tumor angiogenesis, lymphangiogenesis, and metastasis. The VEGF/VEGFR signaling pathway activates various downstream effectors, including phospholipase Cγ1, MAPK, and PI3K/Akt, which are essential for maintaining vascular homeostasis and promoting angiogenesis. In NSCLC, elevated serum VEGF levels have been observed, and the VEGF/VEGFR axis is frequently impaired, leading to irregular blood vessel formation and metastatic spread. Despite the development of anti-VEGF therapies, their impact on lung cancer outcomes has been limited. Further research is needed to optimize the effectiveness of these treatments and elucidate the potential of serum VEGF as a predictive biomarker in NSCLC.

This report describes the pathological findings of acute gastric dilatation syndrome in New World nonhuman primates that died suddenly. The animals were kept in a Zoo and were received proper nutritional and sanitary management. The animals were submitted for necropsy, and macroscopic findings included gastric and duodenal dilation with marked mesenteric vascular congestion. Gastric and intestinal contents were sent for microbiological examination, and bacterial colonies were isolated and identified as Escherichia coli, Streptococcus sp., Salmonella sp., Staphylococcus sp., and Cronobacter sakazakii. The antibiotic sensitivity test revealed that these bacteria had different re-sistance patterns to several antibiotics. Cronobacter sakazakii was susceptible to Ampicillin and Norfloxacin and resistant to Penicillin and Clindamycin. Cronobacter sakazakii is an opportunistic pathogen in animals, frequently reported in cases of human’s enterocolitis. Acute gastric dilata-tion, previously described in Old World nonhuman primates, is a cause of sudden death in Neo-tropical primates and should be considered as a differential diagnosis in cases of sudden mortality in these species. Although its pathogenicity in primates has not been elucidated, the isolation of Cronobacter sakazakii from samples suggests its presence in the environment, emphasizing the need for reinforced hygiene measures, especially of food supplied for these animals.

A reliable and efficient rail track defect detection system is essential for maintaining rail track integrity and avoiding safety hazards and financial losses. Eddy current (EC) testing is a non-destructive technique that can be employed for this purpose. The trade-off between spatial resolution and lift-off should be carefully considered in practical applications to distinguish closely spaced cracks such as those caused by rolling contact fatigue (RCF). A multi-channel eddy current sensor array has been developed to detect defects on rails. Based on the sensor scanning data, defect reconstruction along the rails is achieved using an inverse algorithm that includes both direct and iterative approaches. In experimental evaluations, the EC system with the developed sensor is used to measure defects on a standard test piece of rail with a probe lift-off of 4-6 mm. The reconstruction results clearly reveal cracks at various depths and spacings on the test piece.

Objectives. To compare the audiological benefits of a non-implantable wearing option of a bone conduction (BC) implant mounted on an arch (SoundArc) to traditional BC hearing aids (HA) mounted on eyeglasses (BCHA) in patients with moderate to severe conductive or mixed hearing loss. Methods: A preliminary cross-sectional observational prospective cohort study was conducted at a Tertiary Audiological Department, University Hospital. Fourteen adults with conductive or mixed hearing loss (PTA at 0.5-1-2-4 KHz = 67 ± 15 dB HL) had been wearing conventional BCHA on eyeglasses for at least 3 years, and refused the surgical implantation of a BC hearing implant (BCHI). Unaided and aided pure-tone AC and BC thresholds and speech test in quiet and in noise were recorded at baseline and in two different settings: with a BCHI mounted on SoundArc®, and with their own BCHA with two couplers, mounted on eyeglasses. International Inventory for Hearing Aids [IOI – HA], the Hearing Handicap Inventory [HHIA/E], Speech, Spatial, Qualities of Hearing Scale [SSQ], a 10-scores visuo-analogic scale [VAS], and Fatigue impact scale [FIS] score were asked in both conditions. Results: a statistical significative functional gain was observed for both settings. (p=.0001) Better speech perception performances in quiet and in noise were observed with SoundArc compared to their conventional BCHA on eyeglasses (word repetition score in noise improvement of +19.3 at SNR +10 dB, p=.002; + 12.1 at SNR 0 dB, p=.006; and +11.4 at SNR -10 dB, p=.002) No significant differences were found in IOI–HA, FIS, and HHIA/E scores, while significative better SSQ scores in all domains were reported for SoundArc. (p=.0038) Conclusions: Although patients were accustomed to their BCHA on eyeglasses, the non-implanted wearable option of the BCHI proved to be a viable alternative in adult patients with conductive or mixed hearing loss unable to receive or refusing BCHI surgery.

This study endeavors the preparation and evaluation of Phenol Furfural Resin (PFR) from bagasse and its nanocomposites for Electrically Conductive Adhesives (ECAs) application. PFR was prepared with the furfural extracted from bagasse using modified acid digestion method. Three different formulations of PFR nanocomposites with conductive nanoparticles i.e., PFR-silver, PFR-graphite, and PFR-silver + graphite were prepared using 20-60 w/w% of fillers via impregnation method. Resultant products were characterized by FT-IR, SEM, EDS and XRD spectroscopy. Electrical conductivity was measured using four probe technique while band gap was calculated via Tauc plot. Virgin PFR has shown poor conductivity up to 2.6 × 10^-4 Scm^-1 while the highest conductivity achieved was 8.2 × 10^-1 Scm^-1 for nanocomposite constituted silver, graphite, and PFR with 40:30:20 ratios respectively. This synergism was exhibited because graphite and Ag NPs supply excellent junctions for building networks. Both tend to coalesce due to van der Waals forces and high surface energies, therefore conductive pathways numbers can be increased, and contact area can be effectively enlarged. This ternary composite has exhibited the lowest bandgap energy value i.e., 3.1 eV. Thermogravimetric temperatures T₀ and T_deg values were increased up to 120 °C and 484 °C respectively, showing significant increase in thermal stability. Therefore, the resultant nanocomposite material has good potential to be employed as ECAs in electronic industry.

This study endeavors the preparation and evaluation of Phenol Furfural Resin (PFR) from bagasse and its nanocomposites for Electrically Conductive Adhesives (ECAs) application. PFR was prepared with the furfural extracted from bagasse using modified acid digestion method. Three different formulations of PFR nanocomposites with conductive nanoparticles i.e., PFR-silver, PFR-graphite, and PFR-silver + graphite were prepared using 20-60 w/w% of fillers via impregnation method. Resultant products were characterized by FT-IR, SEM, EDS and XRD spectroscopy. Electrical conductivity was measured using four probe technique while band gap was calculated via Tauc plot. Virgin PFR has shown poor conductivity up to 2.6 × 10-4 Scm-1 while the highest conductivity achieved was 8.2 × 10-1 Scm-1 for nanocomposite constituted silver, graphite, and PFR with 40:30:20 ratios respectively. This synergism was exhibited because graphite and Ag NPs supply excellent junctions for building networks. Both tend to coalesce due to van der Waals forces and high surface energies, therefore conductive pathways numbers can be increased, and contact area can be effectively enlarged. This ternary composite has exhibited the lowest bandgap energy value i.e., 3.1 eV. Thermogravimetric temperatures T0 and Tdeg values were increased up to 120 °C and 484 °C respectively, showing significant increase in thermal stability. Therefore, the resultant nanocomposite material has good potential to be employed as ECAs in electronic industry.

The diamagnetic levitation technique can be applied to non-destructive testing for identifying cracks and defects in magnetic materials. Pyrolytic graphite is a material that can be leveraged in micromachines due to its no-power diamagnetic levitation on a permanent magnet (PM) array. However, the damping force applied to pyrolytic graphite prevents it from maintaining con-tinuous motion along the PM array. This paper investigates the in-plane motion and damping characteristics of pyrolytic graphite sheets on the PM array. The centroid of pyrolytic graphite will maintain a stable levitation when positioned on the intersecting point of the PM array. Fur-thermore, the in-plane motion of two different pyrolytic graphite sizes - PG10 (10×10×0.5mm3) and PG20 (20×20×0.5mm3) - has revealed that the in-plane forces applied to them are approximately 61.4μN and 28.2μN, respectively. The smaller sheet has a shorter oscillation time while oscillating before it stabilizes. The damping ratio of the oscillation was between 0.1-0.2. The in-plane force and the stable time of pyrolytic graphite are related to its size ratio in comparison with the PM. This relationship is believed to promote stability, as the force acting on the graphite sheet will be distributed over a larger area when the sheet size increases. During the fixed-axis rotation process, the study found that the friction coefficient and friction force decreased as the rotational speed decreased. The diamagnetic levitation of pyrolytic diamagnetic levitation is also unable to maintain long-term axial rotation. Finally, friction force was tested using PG10 during fixed-axis rotation above a circular PM array. The results showed that the order of the friction coefficient is 10-3, and the friction force is about 0.8μN, decreasing with graphite rotation speed. We hope this technique will be used in crack detection, magnetic detection and other micromachine.

Non-Vitamin K Oral Anticoagulants (NOACs) have revolutionized anticoagulant therapy, offering improved safety and efficacy over traditional agents like warfarin. This review comprehensively examines the dual roles of NOACs—Apixaban, Rivaroxaban, Edoxaban, and Dabigatran—not only as anticoagulants but also as modulators of inflammation via Protease-Activated Receptor (PAR) signaling. We highlight the unique pharmacotherapeutic properties of each NOAC, supported by key clinical trials demonstrating their effectiveness in preventing thromboembolic events. Beyond their established anticoagulant roles, emerging research suggests that NOACs influence inflammation through PAR signaling pathways, implicating factors such as FXa and Thrombin in the modulation of inflammatory responses. This review synthesizes current evidence on the anti-inflammatory potential of NOACs, exploring their impact on inflammatory markers and conditions like atherosclerosis and diabetes. By delineating the mechanisms by which NOACs mediate anti-inflammatory effects, this work aims to expand their therapeutic utility, offering new perspectives for managing inflammatory diseases. Our findings underscore the broader clinical implications of NOACs, advocating for their consideration in therapeutic strategies aimed at addressing inflammation-related pathologies. This comprehensive synthesis not only enhances understanding of NOACs' multifaceted roles but also paves the way for future research and clinical applications in inflammation and cardiovascular health

Quadruped robots possess significant mobility in complex and uneven terrains due to their outstanding stability and flexibility, making them highly suitable in rescue missions, environmental monitoring, and smart agriculture. With the increasing use of quadruped robots in more demanding scenarios, ensuring accurate and stable state estimation in complex environments has become particularly important. Existing state estimation algorithms relying on multi-sensor fusion, such as those using IMU, LiDAR, and visual data, often face challenges on non-stationary terrains due to issues like foot-end slippage or unstable contact, leading to significant state drift. To tackle this problem, this paper introduces a state estimation algorithm that integrates an Invariant Extended Kalman Filter (InEKF) with a disturbance observer, aiming at estimating the motion state of quadruped robots on non-stationary terrains. Firstly, foot-end slippage is modeled as a deviation in body velocity and explicitly included in the state equations, allowing for a more precise representation of how slippage affects the state. Secondly, the state update process integrates both foot-end velocity and position observations to improve the overall accuracy and comprehensiveness of the estimation. Lastly, a foot-end contact probability model, coupled with an adaptive covariance adjustment strategy, is employed to dynamically modulate the influence of the observations. These enhancements significantly improve the filter's robustness and the accuracy of state estimation in non-stationary terrain scenarios. Experiments conducted with the Jueying Mini quadruped robot on various non-stationary terrains show that the enhanced InEKF method offers notable advantages over traditional filters in compensating for foot-end slippage and adapting to different terrains.