Recognition, decoding and tracking of vortex patterns is of increasing importance in many fields reaching from astronomical observation of distant galaxies to turbulence phenomena in liquids or gases. Currently, coherent light beams with orbital angular momentum (OAM) are of particular interest for optical communication, metrology, micro-machining or particle manipulation. One common task is to identify characteristic spiral patterns in pixelated intensity maps at real-world signal-to-noise ratios. Recently, Fast Fourier Transform (FFT) was applied to the quantitative analysis of spiral interference patterns of OAM beams. Our study considers this approach in more detail. It is demonstrated that specific information can be extracted by combining conformal mapping by polar transform with determining one- or two-dimensional angular frequency spectra either in spatially fixed or scanning mode. Results of proof-of-principle experiments are presented.

In wireless sensor networks (WSNs), each sensor node can estimate the global parameter from the local data in distributed manner. This paper proposed a robust diffusion estimation algorithm based on minimum error entropy criterion with self-adjusting step-size, which are referred to as diffusion MEE-SAS (DMEE-SAS) algorithm. The DMEE-SAS algorithm has fast speed of convergence and is robust against non-Gaussian noise in the measurements. The detailed performance analysis of the DMEE-SAS algorithm is performed. By combining the DMEE-SAS with diffusion minimum error entropy (DMEE) algorithms, an Improving DMEE-SAS algorithm is proposed, in non-stationary environment where tracking is very important. The Improving DMEE-SAS algorithm can avoid insensitivity of the DMEE-SAS algorithm due to the small effective step-size near the optimal estimator, and obtain a fast convergence speed. Numerical simulations are given to verify the effectiveness and advantages of these proposed algorithms.

Master equations define the dynamics that govern the time evolution of various physical processes on lattices. In the continuum limit, master equations lead to Fokker-Planck partial differential equations that represent the dynamics of physical systems in continuous spaces. Over the last few decades, nonlinear Fokker-Planck equations have become very popular in condensed matter physics and in statistical physics. Numerical solutions of these equations require the use of discretization schemes. However, the discrete evolution equation obtained by the discretization of a Fokker-Planck partial differential equation depends on the specific discretization scheme. In general, the discretized form is different from the master equation that has generated the respective Fokker-Planck equation in the continuum limit. Therefore, the knowledge of the master equation associated with a given Fokker-Planck equation is extremely important for the correct numerical integration of the latter, since it provides a unique, physically motivated discretization scheme. This paper shows that the Kinetic Interaction Principle (KIP) that governs the particle kinetics of many body systems, introduced in [G. Kaniadakis, Physica A 296, 405 (2001)], univocally defines a very simple master equation that in the continuum limit yields the nonlinear Fokker-Planck equation in its most general form.

An algorithm for the treatment of images affected by both blurring and salt&pepper noise is proposed with a cost only proportional to the number of pixels. The methodology uses a discretization scheme for the Laplace operator multiplied by a suitable nonlinear term depending on the gradient. Even if this approach resembles a diffusion type algorithm, only one step of the procedure is applied, leading to significant time savings. The procedure is successfully tested on some standard black&white natural images.

Nonlinear catastrophes caused by geological fluids are a fundamental issue in rock mechanics and the geoengineering hazard field. For the consideration of hydrodynamic force on red-bed mudstone softening damage, X-ray visualization test on the fissure flow in mudstone block failure under hydrodynamic force was performed in this study based on block scale and the physical phenomena of fissure seepage and nonlinear diffusion were further explored. A new method for evaluating the hydro-damage degrees of rocks using an X-ray image analysis was proposed, and the quantitative relation of diffusion coefficients of hydro-damage and seepage was established. The research results revealed that the hydrodynamic force promoted the fluid-filled fissure behavior in mudstone specimen failure. Also, the seepage and diffusion phenomena of fluid in rocks during failures were indicated using X-ray imaging. A dual mechanical behavior was presented in the nonlinear seepage and abnormal diffusion of a red mudstone geological body under hydrodynamic conditions. The damaged degree of mudstone was aggravated by the effect of hydrodynamic force, and the initial seepage–diffusion coefficient with respect to lower hydro-damage was larger than the final seepage–diffusion coefficient with respect to higher hydro-damage of rocks with a decreasing nonlinear trend.

The fractional advection-dispersion equation FADE plays an important role, especially in explaining the process of solute-transport in natural porous media with different degrees of heterogeneity. However, studies of the flow and transport of contaminants in the underground environment are based on the knowledge of many functional parameters of the subsoil. The delay factor caused by nonlinear absorption is one of these parameters inheriting significant ambiguities in its estimation in heterogeneous media. In the study, a fractional advection-dispersion FADE model was developed by the implicit Euler method, based on a Grunwald and Caputo-Liousville approximation to explicitly evaluate and simulate the transport mechanism of contaminants in media with unsaturated porous materials subjected to a nonlinear sorption model. Better solute mass retention was observed for fractional advection-dispersion FADE model. Moreover, the absorption parameter of the retardation coefficient has a better impact on the motion of the solute in a saturated porous medium. In other words, it has a significant effect on the dispersion of pollutants in aquifers. This study highlights the need to characterize the aquifer to predict solute transport in porous media.

The splitting method developed in a previous study for linear, multi – component, convection-diffusion mass transfer equations is extended to non-linear, multi-component, convection-diffusion mass transfer equations. The diffusion term is non-linear (the diffusion coefficients depend on chemical species concentrations). Theoretical results about the splitting error are presented, as well as numerical simulations for mixtures with n ≤ 5. The numerical experiments show second-order accuracy and stability for the present splitting algorithm.

Purpose: Prostate cancer remains the 2nd leading cancer killer of men, yet it is also a disease with a high rate of overtreatment. Diffusion weighted imaging (DWI) has shown promise as a reliable, grade-sensitive imaging method, but it is limited by low image quality. Currently, DWI image quality is directly related to low gradient ampli-tudes, since weak gradients must be compensated with long echo times. Methods: We propose a new type of MRl accessory, an "inside-out" and nonlinear gradient, whose sole purpose is to deliver diffusion encoding to a region of interest. Performance was simulated in OPERA and the resulting fields were used to simulate DWI with two compartment and kurtosis models. Experiments with a nonlinear head gradient prove the accuracy of DWI and ADC maps diffusion encoded with nonlinear gradients. Results: Simulations validated thermal and mechanical safety while showing a 5 to 10-fold increase in gradient strength over prostate. With these strengths, lesion CNR in ADC maps approximately doubled for a range of anatomical positions. Proof-of-principle experiments show that spatially varying b-values can be corrected for accurate DWI and ADC. Conclusions: Dedicated nonlinear diffusion encoding hardware could improve prostate DWI.

The chiral optical Tamm state (COTS) is a special localized state at the interface of a handedness-preserving mirror and a structurally chiral medium such as a cholesteric liquid crystal or a chiral sculptured thin film. The spectral behavior of COTS, observed as reflection resonances, is described by the temporal coupled-mode theory. Mode coupling is different for two circular light polarizations because COTS has a helix structure replicating that of the cholesteric. The mode coupling for co-handed circularly polarized light exponentially attenuates with the cholesteric layer thickness since the COTS frequency falls into the stop band. Cross-handed circularly polarized light freely goes through the cholesteric layer and can excite COTS when reflected from the handedness-preserving mirror. The coupling in this case is proportional to anisotropy of the cholesteric and theoretically it is only anisotropy of magnetic permittivity that can ultimately cancel this coupling. These two couplings being equal results in a polarization crossover (the Kopp--Genack effect) for which a linear polarization is optimal to excite COTS. The corresponding cholesteric thickness and scattering matrix for COTS are generally described by simple expressions.

The numerical implementation of the controllers allows the use of very complex algorithms with ease. However, in practice, due to its proven advantages, the PID controller (and its variants) is widely used in industrial control systems as well as in many other applications that require continuous control. Most of the methods for tuning the parameters of PID controllers are based on time-invariant linear models of the processes, which in practice can lead to poor performance of the control system. The paper presents an application of reinforcement learning algorithms in tuning of PID controllers for the control of some classes of continuous nonlinear systems. Tuning the parameters of PID controllers is done with the help of Twin Delayed Deep Deterministic Policy Gradients (TD3) algorithm which presents a series of advantages compared to other similar methods from Machine Learning dedicated to continuous state and action spaces. TD3 algorithm is an off-policy Actor-Critic based method and was used as it does not require a system model. The presented technique is applied for control of a biotechnological system which has a strongly nonlinear dynamic. The proposed tuning method is compared to the classical tuning methods of PID controllers. The performance of the tuning method based on the TD3 algorithm is demonstrated through simulation illustrating the effectiveness of the proposed methodology.

This paper proposed an optimal tracking control scheme through adaptive dynamic programming(ADP) for a class of partially unknown discrete-time nonlinear systems based on radial basis function neural network(RBF-NN). In order to acquire the unknown system dynamics, we use two RBF-NNs, the one is used to construct the identifier, and the another is used to directly approximate the steady-state control input, where a novel adaptive law is proposed to update neural network weights. While the optimal feedback control and the cost function are derived via feedforward neural networks approximating, it is proposed to regulate the tracking error, the critic network and the actor network are then trained online to obtain the solution of the associated Hamilton–Jacobi–Bellman (HJB) equation being built under the ADP framework. Simulations verify the effectiveness of the optimal tracking control technique using the neural networks.

The instability of traveling pulses in nonlinear diffusion problems is inspected on the example of Gunn domains in semiconductors. Mathematically the problem is reduced to the calculation of the "energy" of the ground state in Schrödinger equation with a complicated potential. A general method to obtain the bottom-part spectrum of such equations based on the approximation of the potential by square wells is proposed and applied. Possible generalization of the approach to other types of nonlinear diffusion equations is discussed.

While numerous studies have explored the correlation between the built environment and ride-hailing demand, few have assessed their nonlinear interplay. Utilizing ride-hailing order data and multi-source built environment data from Nanjing, China, this paper uses the machine learning method, eXtreme Gradient Boosting (XGBoost), combined with SHapley Additive exPlanations (SHAP) and Partial Dependence Plots (PDP) to investigate the impact of built environment factors on ride-hailing travel demand, including their non-linear and threshold effects. The findings reveal that dining facilities have the most significant impact, with a contribution rate of 30.75%, on predicting ride-hailing travel demand. Additionally, financial, corporate, and medical facilities also exert considerable influence. The built environment factors need to reach a certain threshold or within a certain range to maximize the impact of ride-hailing travel demand. population density, land use mix and distance to the subway station collectively influence ride-hailing demand. The results are helpful for TNCs to allocate network ride-hailing resources reasonably and effectively.

In this paper, we consider a fourth-order suspension bridge equation with nonlinear damping term |u_t|^m-2u_t and source term |u|^p-2u. We give necessary and sufficient condition for global existence and energy decay results without considering the relation between m and p. Moreover, when p>m, we give sufficient condition for finite time blow-up of solutions. The lower bound of the blow-up time T_max is also established. It worth to mention that our obtained results extend the recent results of Wang (J. Math. Anal. Appl., 2014) to the nonlinear damping case.

In current transportation hubs, it is a common phenomenon that passengers travel with necessary wheeled-luggage or suitcases. Due to the fact that most luggage occupies certain space within dense passenger crowds with giant mass inertia, its abnormal motions, such as drifting, frequently trig unavoidable local disturbances and turbulence in surrounding pedestrian flows, further increasing security risk. While, current researches primarily concentrate on examining the impact of luggage on crowd evacuation efficiency through scenario-based experiments and analyzing the spatial characteristics of crowd distribution in surveillance videos. There still lacks of the dynamic disturbance mechanisms and crowd stability associated with the combined motion of passengers and luggage. Therefore, this study considers the luggage-laden passenger as a deformable particle, the resulting disturbance on surrounding non-luggage passengers is analyzed and quantified into a nonlinear pressure term. Subsequently, the disturbance propagation model of passenger-luggage is developed by adapting the classical Aw-Rascle traffic flow model with incorporation of the pressure term. Simulation experiments of disturbances caused by luggage drifting and retrograding validate that the proposed propagation model aligns with real-world situations in transportation hubs. Quantitively, when luggage-laden passenger drifted left, the disturbing force of left side crowd can reach a peak of 238N in the passenger density of 3.0 p/m2, and the maximum difference between the left and right sides disturbing force can reach 153N. Furthermore, it is recommended that the proposed model can be applied to crowd flow analysis and risk assessment.

This paper aims to address the exponential stability and stabilization problems for a class of delayed nonlinear Markov jump systems under randomly occurring Denial-of-Service (DoS) attack and packet loss. Firstly, the stochastic characteristics of DoS attack and packet loss are depicted by the attack success rate and packet loss rate. Secondly, a Period Observation Window (POW) method and a hybrid-input strategy are proposed to compensate for the impact of DoS attack and packet loss on the system. Thirdly, A Dynamic Event-triggered Mechanism (DETM) is introduced to save more network resources and ensure the security and reliability of systems. Then, by constructing a general common Lyapunov functional and combining with the DETM and other inequality analysis techniques, the less conservative stability and stabilization criteria for the underlying systems are derived. In the end, the effectiveness of our result is verified through a numerical example.

This paper addresses the analysis for the nonlinear vibration response of a rectangular tube with a flexible end and non-rigid acoustic boundaries. This is a further work of the linear structural acoustic problem in a well-known acoustic book. In fact, the acoustic boundaries of an enclosed space sometimes are non-rigid and the structural vibration responses are nonlinear. These two points are the focuses of this paper. The multi-level residue harmonic balance method is applied to this nonlinear structural acoustic problem. The results obtained from the multi-level residue harmonic balance method and numerical method are generally in good agreement. The effects of excitation magnitude, tube length, and phase shift parameter etc. are examined.

The generation and maintenance of membrane potential is a fundamental part of Membrane Pump Theory. One of the key points of this hypothesis is based on a natural or facilitated molecular diffusion through several types of ion channels and pumps like the Na/K ATPase. Chemistry, physics and especially electrochemistry, however, bring strong contradictions to this theoretical assumption. By respecting the principles of chemistry and electrostatics, it becomes obvious that this theoretical hypothesis cannot work. The ionic diffusion that would be at the origin of this potential cannot take place. Indeed, the topology and the forces involved definitively exclude the current model, which must absolutely be revised according to the current state of our knowledge and allow an advance in the understanding of the phenomena and open new research perspectives.

For the past few decades, researchers have been intrigued with glassy polymers, which have applications ranging from gas separations to corrosion protection to drug delivery systems. The techniques employed to examine the sorption and diffusion of small molecules in glassy polymers are the subject of this review. Diffusion models in glassy polymers are regulated by Fickian and non-Fickian diffusion, with non-Fickian diffusion being more prevalent. The characteristics of glassy polymers are determined by sorption isotherms, and different models have been proposed in the literature to explain sorption in glassy polymers during the last few years. This review also includes the applications of glassy polymer. Despite having so many applications, current researchers still have difficulty in implementing coating challenges due to issues like as physical ageing, which is briefly discussed in the review.

The paper examines the impact of inward remittances flows on per capita GDP growth in Bangladesh during 1976-2012. We find that the growth effect of remittances is negative at first but becomes positive at a later stage, an evidence of a non-linear. Unproductive use of remittances was rampant in the beginning when they were received by migrant families but better social and economic investments led to more productive utilisation of remittances receipts at later periods. This was the possible mechanism behind the U-shaped relationship. Unlike what is suggested in the literature that the effect of remittances is more pronounced in a less financially developed economy, our evidence do not show that the effect of remittances on per capita GDP growth in Bangladesh is conditional on the level of financial development.

In the framework of the self-consistent Maxwell-Pauli theory, the non-linear Pauli equation is obtained. Stationary and nonstationary solutions of the nonlinear Pauli equation for the hydrogen atom are studied. We show that spontaneous emission and the related rearrangement of the internal structure of an atom, which is traditionally called a spontaneous transition, have a simple and natural description in the framework of classical field theory without any quantization and additional hypotheses. The behavior of the intrinsic magnetic moment (spin) of an electron wave in an external magnetic field is considered. We show that, according to the self-consistent Maxwell-Pauli theory, in a weak magnetic field, the intrinsic magnetic moment of an electron wave is always oriented parallel to the magnetic field strength vector, while in a strong magnetic field, depending on the initial orientation of the intrinsic magnetic moment, two orientations are realized: either parallel or antiparallel to the magnetic field strength vector.

The diffusion coefficient (D) is a key parameter characterizing gas transport in coal seams. Usually, the D is calculated from the desorption curve of particle coal, which cannot accurately reflect the diffusion characteristics under the stress constraint conditions of in-situ coal seams. In this paper, based on Fick's law of counter diffusion, different metamorphic deformed coals of medium and high coal rank are taken as the research object. The change laws of D under different confining pressure, gas pressure, and temperature conditions are tested and analyzed, and the influencing mechanisms on the D are discussed. The results show that the D of different metamorphic deformed coals decreases exponentially with the increase of confining pressure, and increases exponentially with the increase of gas pressure and temperature. There is a limit diffusion coefficient. The influence of confining pressure on the D is essentially determined by the change of effective stress, and the D has a negative effect of effective stress similar to permeability. The effect of gas pressure on the D involves two mechanisms, namely, mechanical and adsorption effects, which are jointly restricted by effective stress and coal particle shrinkage and expansion deformation. The effect of temperature on the D is mainly achieved by changing the root mean square speed and average free path of gas molecules. Under the same temperature and pressure conditions, the D increases first and then decreases with the increase of deformation degree, and the D of fragmented coal is the largest. Under similar deformation conditions, the D of high-rank anthracite is greater than that of medium-rank fat coal. It is considered that porosity is the key factor affecting the change of D in different metamorphic deformed coals.

An interesting anomaly of the diffusion process with an apparently negative diffusion coefficient defined through the mean-square displacement in a one-dimensional quantum molecular chain model is shown. Nevertheless, the system satisfies the H-theorem, so that the second law of thermodynamics is satisfied. The reason why the “diffusion constant” becomes negative is due to the effect of the phase mixing process, which is a characteristic result of the one-dimensionality of the system. We illustrate the situation where this negative “diffusion constant” appears.

Imperfection sensitivity of large amplitude vibration of curved single-walled carbon nanotubes (SWCNTs) is considered in this study. The SWCNT is modeled as a Timoshenko nano-beam and its curved shape is included as an initial geometric imperfection term in the displacement field. Geometric nonlinearities of von Kármán type and nonlocal elasticity theory of Eringen are employed to derive governing equations of motion of nano-beam. Spatial discretization of governing equations and associated boundary conditions is performed using differential quadrature (DQ) method and the corresponding nonlinear eigenvalue problem is iteratively solved. Effects of value and location of the geometric imperfection, and the nonlocal small-scale parameter on the nonlinear frequency ratio and imperfection sensitivity of a curved SWCNT for various boundary conditions are investigated. The results show that the geometric imperfection plays a significant role in the nonlinear vibration characteristics of curved SWCNTs.

Diffusion bonding is often used on pre-machined parts to generate internal cavities, e.g. for cooling injection molding tools close to the mold cavity. Only then, the workpieces are finished to their final dimensions. In the case of micro-process devices, however, it is essential to precisely control the deformation, as otherwise uncontrollable pressure losses will occur with channel cross-sections in the sub-millimeter range. Post-processing is not possible. The most important process parameters for diffusion bonding are temperature, dwell time and contact pressure, with the bonding temperature and contact pressure acting in opposite directions and showing a strong non-linear dependence on deformation. In addition, the deformation is influenced by a number of other factors such as the absolute size of the cross-section and the aspect ratio of the parts, the dimensions and distribution of the internal cross sections and the overall percentage of the cross-section to be bonded. In micro process engineering, small material cross-sections in the range of the materials microstructure can facilitate additional deformation mechanisms such as grain boundary sliding, which are not relevant at all for larger structures. For parts consisting of multiple layers, tolerances in thickness and roughness of multiple surfaces must be levelled, contributing to the percentaged deformation. This makes it difficult, especially in micro process engineering and in single or small series production, to determine suitable joining parameters in advance, which on the one hand do not cause unforeseen large deformations, but on the other hand reliably produce highly vacuum-tight components. Hence, a definition of a fixed percentaged deformation does not work for all kinds of components. This makes it difficult to specify parameters for surely obtain high-vacuum tight parts. For successful diffusion bonding, atoms must diffuse over the bonding planes, forming a monolithic part in which the original layers are no longer visible. Only then, mechanical properties identical to those of the base material, which has been subjected to identical heat treatment, can be achieved. In this paper, the impacts of different material cross section widths as well as of the aspect ratio on deformation were investigated. By accident, it was found that also accuracy of the temperature measurement may have a serious impact in terms of deformation.

It is shown by numerical modelling that anisotropic diffusion can compensate and even overcome diffusion broadening - the main limiting factor of devices working at atmospheric pressure. The thickness of ion clouds coming out of the ionisation chamber is reduced ~ 1000 times in the ADMA inlet increasing the resolution. This finding has a great potential that enables construction of a device with resolution close to that of currently available desktop ion separation devices – high pressure mass spectrometers, but with much lower cost of manufacture and with smaller dimensions. Comprehensive numerical modelling along with mathematical analysis of physical concepts enables reduction of the footprint and manufacturing costs. Modelling determined that the resolving power (RP) potential of the ADMA is greater than the RP of currently available on the market devices for the airport security market. The ADMA technology enables very fast detection of threats; at least 100 times faster than currently used in Ion Mobility Spectrometers (IMS). This potentially allows an increase in passenger throughput in airports.

A set of programs for the numerical simulation of the diffusion decomposition processes was developed by using simulation methods, kinetic and particle method. The complex has been validated on the model system Ni-Al by the growth of -phase separations. The results on the evolution of the distribution function and other characteristics of the ensemble, which in the zero volume fraction approximation are asymptotically in good agreement with the theory and the experiment, have been obtained. The peculiarity of the created program complex is the possibility of its adaptation to the description of the decomposition of multicomponent multiphase systems. Fig. 6, list of references - 19 titles.

This article is devoted to Feller's diffusion equation which arises naturally in probabilities and physics (e.g. wave turbulence theory). If discretized naively, this equation may represent serious numerical difficulties since the diffusion coefficient is practically unbounded and most of its solutions are weakly divergent at the origin. In order to overcome these difficulties we reformulate this equation using some ideas from the Lagrangian fluid mechanics. This allows us to obtain a numerical scheme with a rather generous stability condition. Finally, the algorithm admits an elegant implementation and the corresponding Matlab code is provided with this article under an open source license.

In a bid to resolve lingering problems in cosmology, more focus is being tilted towards cosmological models in which physical constants of nature are not necessarily real constants, but varying with cosmic time. In this paper we have study cosmology in nonlinear electrodynamics with the Newton's gravitational constant $G$ not a constant but vary in form of power-law of the scale factor of the universe. The evolution of the scale factor $a (t)$ is studied in this model which depends on nonlinear electrodynamics fine tuning term of $\alpha$. Then we check the stability of the model using the speed of sound.

We discuss methods for calculation of critical indices and amplitudes from the perturbative expansions. Several important examples of the Stokes flow through 2D and 3D channels are brought up. Power series for the permeability derived for small values of amplitude are employed to calculation of various critical exponents in the regime of large amplitudes. Special nonlinear approximations valid for arbitrary values of the wave amplitude are derived from the expansions. The technique developed for critical phenomena is applied then for relaxation phenomena. The concept of time-translation invariance is discussed, its spontaneous violation and restoration considered. Emerging probabilistic patterns correspond to a local breakdown of time-translation invariance. Their evolution leads to the timetranslation symmetry complete (or partial) restoration. We estimate typical time extent, amplitude and direction for such restorative process. The new technique is based on explicit introduction of origin in time. After some transformations we come to the exponential and generalized, exponential-type solution with explicit finite time scale, which was only implicit in initial parametrization with polynomial approximation. The concept of crash as a relaxation phenomenon, consisting of time-translation invariance breaking and restoration, is put forward. COVID-19 related mini-crash in the time series for Shanghai Composite is discussed as an illustration.

Time evolution of the quantum correlation of the hybrid qubit-qutrit system in multilocal and global dephasing under the effect of a classical noises environment is presented. We considered the qutrit in z direction and the qubit x direction. In addition, our system presents two configurations: the different and the common environment and our discussion involves three types of noises: A Static Noise (SN), Random Telegraph Noise (RTN) and Ornstein- Uhlenbeck noise (OU). By using the density matrix approach to determine the evolution of the state of the system, the found that the static noise is fatal for the quantum entanglement, the quantum correlation and for RTN and OU noises the quantum entanglement, the quantum correlation decreases monotonically with a sufficiently long time. Therefore, we can say that, entanglement and the quantum correlation are more robust to the noise precisely those Random telegraph noise and Ornstein-Uhlenbeck noise.

This paper considers a nonlinear model for population dynamics with age structure. The fertility rate with respect to age is non constant and has the form proposed by . Moreover, its multiplicative structure and the multiplicative structure of mortality makes the model separable. In this setting it is shown that the number of births in unit time is given by a system of nonlinear ordinary differential equations. The steady state solution together with the equilibrium solution is found explicitly.

We show that one of the two important uncertainty principles derived by Maccone and Pati \textit{[Phys. Rev. Lett., 2014]} can be derived for arbitrary maps defined on subsets of $\mathcal{L}^p$ spaces for $1< p<\infty$. Our main tool is the Clarkson inequalities. We also derive a nonlinear uncertainty principle for weak parallelogram spaces and Type-p Banach spaces.

According to our current understanding of quantum mechanics, a `measurement' violates unitarity. In other words as the act of measurement `resets' the probabilities described by the Schrödinger equation, in the very `moment' of the collapse of the wavefunction, conservation of probability does not hold. To make progress in our understanding of the measurement problem it is thus expected that one must encompass in a single equation both otherwise mutually-exclusive processes of measurement and unitary evolution. In this light, turning to the continuity equation, we realize the possibility that if we allow for existence of sources and sinks in the `fluid of probability' we get closer to such a theory by arriving at nonlinear generalizations of Schrödinger and Klein-Gordon equations. The generalized equations derived are then shown to satisfy all conditions that are expected from a proper generalization: simplification to their linear counterparts by a well-defined dynamical condition, and Galilean and Lorentz invariance.

Continuation methods are presented that are capable of treating frequency-domain flutter equations including multiple nonlinearities represented by describing functions. A small problem demonstrates how a series of continuation processes can find all limit-cycle oscillations within a specified region with a reasonable degree of confidence. Curves of the limit-cycle amplitude variation with velocity, indicating regions of stability and instability with colors give a compact view of the nonlinear behavior throughout the flight regime. A continuation technique for reducing limit-cycle amplitudes by adjusting various system parameters is presented. These processes are economical enough to be a routine part of aircraft design and certification.

The study of different forms of preconditioners for solving a system of nonlinear equations, by using Newton’s method, is presented. The preconditioners provide numerical stability and rapid convergence with reasonable computation cost, whenever chosen accurately. Different families of iterative methods can be constructed by using a different kind of preconditioners. The multi-step iterative method consists of a base method and multi-step part. The convergence order of base method is quadratic and each multi-step add an additive factor of one in the previously achieved convergence order. Hence the convergence of order of an m-step iterative method is m + 1. Numerical simulations confirm the claimed convergence order by calculating the computational order of convergence. Finally, the numerical results clearly show the benefit of preconditioning for solving system of nonlinear equations.

Pulsed-field gradient (PFG) diffusion experiments can be used to measure anomalous diffusion in many polymer or biological systems. However, it is still complicated to analyze PFG anomalous diffusion, particularly the finite gradient pulse width (FGPW) effect. In practical applications, the FGPW effect may not be neglected such as in clinical diffusion magnetic resonance imaging (MRI). Here, two significantly different methods are proposed to analyze PFG anomalous diffusion: the effective phase shift diffusion equation (EPSDE) method and an observing the signal intensity at the origin method. The EPSDE method describes the phase evolution in virtual phase space, while the method to observe the signal intensity at the origin describes the magnetization evolution in real space. However, these two approaches give the same general PFG signal attenuation including FGPW effect, which can be numerically evaluated by a direct integration method. The direct integration method is fast and without overflow. It is a convenient numerical evaluation method for Mittag-Leffler function type PFG signal attenuation. The methods here provide a clear view of spin evolution under field gradient, and their results will help the analysis of PFG anomalous diffusion.

: Oscillation synchronization through diffusion-based communication of active materials can lead to emergence of diverse patterns and collective behaviors. A detailed general description of the formation process of synchronization or resynchronization dynamics is a challenging task. We employ a photosensitive Belousov-Zhabotinsky reaction-diffusion model (within a gel media) to investigate the recovery process of oscillation synchronization between a pair of gel patches. The recovery time for oscillation resynchronization can be modulated by patch-distance, species of signaling molecules, intensity and duration of illumination. Analysis reveals that the “switch effect” of the gel-distance and the “promotion effect” from illumination on the oscillation resynchronization originate from the competition between processes of photo-promotion of oscillation, diffusion of signaling molecules (HBrO2 and Br-) and disproportionation of HBrO2. These results will benefit studies on bio-inspired active materials and soft motors.

The focus of this paper is on analyzing the role and the choice of parameters in sociophysics diffusion models, by leveraging the potentialities of sociophysics from a mathematical programming perspective. We first present a generalised version of Galam’s opinion diffusion model (see, e.g. , ). For a given selection of the coefficients in our model, this proposal yields the original Galam’s model. The generalised model suggests guidelines for possible alternative selection of its parameters that allow to foster diffusion. Examples of the parameters selection process as steered by numerical optimisation, taking into account various objectives, are provided.

Dynamics of human populations can be affected by various socio-economic factors through their influence on the natality and mortality rates, and on the migration intensity and directions. In this work we study an economic-demographic model which takes into account the dependence of the wealth production rate on the available resources. In the case of nonlocal consumption of resources the homogeneous in space wealth-population distribution is replaced by a periodic in space distribution for which the total wealth increases. For the global consumption of resources, if the wealth redistribution is small enough, then the homogeneous distribution is replaced by a heterogeneous one with a single wealth accumulation center. Thus, economic and demographic characteristics of nonlocal and global economies can be quite different in comparison with the local economy.

Almost all modern inorganic light-emitting diode (LED) designs are based on double heterojunctions (DHJs) whose structure and current injection principle have remained essentially unchanged for decades. Although highly efficient devices based on the DHJ design have been developed and commercialized for energy-efficient general lighting, the conventional DHJ design requires burying the active region (AR) inside a pn-junction. This has hindered the development of emitters utilizing nanostructured ARs located close to device surfaces such as nanowires or surface quantum wells. Modern DHJ III-N LEDs also exhibit resistive losses which arise from the DHJ device geometry. The recently introduced diffusion-driven charge transport (DDCT) emitter design offers a novel way to transport charge carriers to unconventionally placed ARs. In a DDCT device, the AR is located apart from the pn-junction and the charge carriers are injected into the AR by bipolar diffusion. This device design allows the integration of surface ARs to semiconductor LEDs and offers a promising method to reduce resistive losses in high power devices. In this work, we present a review of the recent progress in gallium nitride (GaN) based DDCT devices, and an outlook of potential DDCT has for opto- and microelectronics.

The principles of causality and unitarity are studied within rational nonlinear electrodynamics proposed earlier. We investigate dyonic and magnetized black holes and show that in the self-dual case, when the electric charge equals the magnetic charge, corrections to Coulomb's law and Reissner-Nordstrom solutions are absent. In the case of the magnetic black hole, the Hawking temperature, the heat capacity and the Helmholtz free energy are calculated. It is shown that there are second-order phase transitions and it was demonstrated that at some range of parameters the black holes are stable.

A harmful impact of climate change and global warming has concerned various sectors of the international community. Numerous energy policies aiming at climate change mitigation have been implemented on a national and global scale. Renewable Energy Technologies (RET) play a critical role in enhancing sustainable solutions that significantly limit greenhouse gases (GHG) emissions. Such innovative technologies can facilitate energy transition through providing e.g. energy security, sustainable development, or effective usage of indigenous resources. However, the commercialization of RET becomes extremely challenging. The barriers can be of a different nature, although in this study the focus has been put on socio-economic and regulatory issues. In fact, there is ample evidence that energy policies play a central role in supporting renewables adoption. It is also claimed that RET require the whole ecosystem to support their successful diffusion. In this study, we explore multifarious barriers for a widespread RET diffusion in two European Union countries: Finland and Poland, indicating the most common barriers existing in the literature as well as analyzing major bottlenecks in the viewpoint of renewable energy companies’ executives. We also present statistics of the most commonly used RET in these countries in order to express the diffusion issues more appropriately. The outcomes of this study provide useful insight for the researchers in the energy transition field as well as practical managerial and regulatory implications aimed at overcoming these challenges.

A number of experiments suggest that the elementary particles are non-local entities. A dissipative self-organization, that treats particles as open systems may provide a better understanding of the underlying phenomena than conservative models. The proposed toy model is such an attempt. We found that self-gravitation (although accompanied by self-diffusion) may not only be compatible with the quantum phenomena but is perhaps the major reason for the existence of quantum fields. According to the proposed model, fields/particles (resemble those of the Standard Model) emerge from a dynamic self-organized medium (which we associate with vacuum dust) from competition between self-gravitation and self-diffusion. These forces produce turbulence in the form of vortices (which we call vacuum cells) that serve as the building blocks for fields and particles. Field/particle features and symmetries are based on their internal (intracellular) dynamics and vortex synchronization (intercellular dynamics). This model allows for rough estimations of relative field coupling strengths, the quantity of charges and flavors, the probabilities of quark transmutations, the dimensionality and the topologies of phase spaces, and other Standard Model parameters that came not from the theory but rather determined by experiment.

We show that Universe inflation occurs when Einstein's gravity couples to nonlinear electromagnetic fields with cosmic stochastic magnetic fields background. Nonlinear electrodynamics with two parameters is used. The strength of magnetic fields to have the Universe inflation is obtained. It is shown that singularities of the energy density and pressure are absent for any scale factors. At large scale factors one arrives at equation of state for ultra-relativistic case. It is demonstrated that the curvature invariants do not have singularities. By computing the deceleration parameter we show that graceful exit takes place with reasonable e-folding number. The duration of Universe inflation as a function of model parameters is obtained. The classical stability and causality are analyzed by calculating the speed of the sound.

We derive an uncertainty principle for Lipschitz maps acting on subsets of Banach spaces. We show that this nonlinear uncertainty principle reduces to the Heisenberg-Robertson-Schrodinger uncertainty principle for linear operators acting on Hilbert spaces.

The article analyzes existing materials and structures with quadratic-nonlinear optical properties that can be used to generate a difference frequency in the terahertz and sub-terahertz frequency ranges. The principle of constructing a nonlinear optical-radio converter, based on an optical focon (a focusing cone), is proposed. Based on the assumption that this focon can be implemented from the metal-organic framework (MOF), we propose a technique for modeling its parameters. The mathematical model of the process of propagation and nonlinear interaction of waves inside the focon is based on a simplification of the nonlinear wave equation. Within the framework of the developed model, the following parameters are approximately determined: the 3D gradient of the linear refractive index and the function determining the geometric profile of the focon, which provide a few-mode-based generation of the difference frequency.

The nonlinear deformation and stress analysis of a circular torus is a difficult undertaking due to its complicated topology and the variation of the Gauss curvature. A nonlinear deformation (only one term in strain is omitted) of Mindlin torus was formulated in terms of the generalized displacement, and a general Maple code was written for numerical simulations. Numerical investigations show that the results obtained by nonlinear Mindlin, linear Mindlin, nonlinear Kirchhoff-Love, and linear Kirchhoff-Love models are close to each other. The study further reveals that the linear Kirchhoff-Love modeling of the circular torus gives good accuracy and provides assurance that the nonlinear deformation and stress analysis (not dynamics) of a Mindlin torus can be replaced by a simpler formulation, such as a linear Kirchhoff-Love theory of the torus, which has not been reported in the literature.

This paper constituted an extension of two previous studies concerning the mathematical development of the grain boundary grooving in polycrystalline thins films in the cases of the evaporation/condensation and diffusion taken separately. The thermal grooving processes are deeply controlled by the various mass transfer mechanisms of evaporation–condensation, surface diffusion, lattice diffusion, and grain boundary diffusion. This study proposed a new original analytical solution to the mathematical problem governing the grain groove profile in the case of simultaneous effects of evaporation-condensation and diffusion in polycrystalline thin films submitted to thermal and mechanical stress, and fatigue effects; by resolving the corresponding fourth-order partial differential equation ∂y∂t=C∂2y∂x2-B∂4y∂x4 obtained from the approximation y'2≪1. The comparison of the new solution to that of diffusion alone proved an important effect of the coupling of evaporation and diffusion on the geometric characteristics of the groove profile. A second analytical solution based on the series development was also proposed. It was proved that change of the boundary conditions of the grain grooving profile largely affected the different geometric characteristics of the groove profile.

Polymer electrolyte was used as a medium for testing the performance of microband electrodes under conditions of linear diffusion. Cyclic voltammetry and chronoamperometry experiments were performed in such viscous medium, where diffusion rates are much slower than in fluid solutions. Confirmation of the existence of such conditions from the log i vs. log v or log i vs. log t relationships in the current equation always yielded values lower than the expected value of 0.5. This could indicate impure linear diffusion profile, i. e. some contribution from radial diffusion (edge effect). However, performing these tests in monomeric solvents of similar viscosities, such as glycerol or propylene glycol, gave the desired value of 0.5. These results lead to the conclusion that current equations which are based on Fick’s laws may not be applicable for polymer electrolytes, where various obstruction to diffusion make it a more complicated process than in monomeric solvents.

The presence of phase diffusion can lead to the loss of the advantages of quantum measurements. Squeezing is considered to be an effective method to reduce the detrimental effect of phase diffusion on the measurement. The Mach-Zehnder (MZ) interferometer has been exploited as a generic tool for precise phase measurement. Describing the reduction in quantum advantage caused by phase diffusion in an MZ interferometer that can be mitigated by squeezing is not easy to handle analytically, because the input state will change from a pure state to a mixed state after experiencing the diffusion noise in the MZ interferometer. We introduce a truncated MZ interferometer that can achieve the same potential phase sensitivity as the conventional MZ interferometer. This scheme can theoretically explain how phase diffusion reduces phase estimation and why squeezing counteracts in the presence of phase diffusion. Using the Gaussian property of the input state and the characteristic of Gaussian operation in the squeezing, the two orthogonal field quantities of the quantum state are squeezed and anti-squeezed to different degrees, and the analytic results are obtained. The truncated MZ interferometer is simpler to build and operate than the conventional MZ interferometer, and also mitigates the phase diffusion noise by the squeezing operation, thus making it useful for applications in precision metrology.

We present a new mathematical model of disease spread reflecting specialties of covid-19 epidemic by elevating the role social clustering of population. The model can be used to explain slower approaching herd immunity in Sweden, than it was predicted by a variety of other mathematical models; see graphs Fig. \ref{GROWTH2}. The hierarchic structure of social clusters is mathematically modeled with ultrametric spaces having treelike geometry. To simplify mathematics, we consider homogeneous trees with $p$-branches leaving each vertex. Such trees are endowed with algebraic structure, the $p$-adic number fields. We apply theory of the $p$-adic diffusion equation to describe coronavirus' spread in hierarchically clustered population. This equation has applications to statistical physics and microbiology for modeling {\it dynamics on energy landscapes.} To move from one social cluster (valley) to another, the virus (its carrier) should cross a social barrier between them. The magnitude of a barrier depends on the number of social hierarchy's levels composing this barrier. As the most appropriate for the recent situation in Sweden, we consider {\it linearly increasing barriers.} This structure matches with mild regulations in Sweden. The virus spreads rather easily inside a social cluster (say working collective), but jumps to other clusters are constrained by social barriers. This behavior matches with the covid-19 epidemic, with its cluster spreading structure. Our model differs crucially from the standard mathematical models of spread of disease, such as the SIR-model. We present socio-medical specialties of the covid-19 epidemic supporting our purely diffusional model.

We present three reduced integrable hierarchies of nonlocal integrable NLS type equations from a vector integrable hierarchy associated with a matrix Lie algebra, not being A type. Three similarity transformations are taken to keep the invariance of the transformed zero curvature equations. The key step is to formulate a solution to a reduced stationary zero curvature equation so that the zero curvature formulation works for a reduced case.

It is known that ammonium has a higher permeability through anion-exchange and bipolar membranes compared to K+ cation that has the same mobility in water. However, the mechanism of this high permeability is not clear enough. We develop a mathematical model based of the Nernst-Planck and Poisson equations for diffusion of ammonium chloride through an anion-exchange membrane; proton exchange reactions between ammonium, water and ammonia are taken into account. It is assumed that ammonium, chloride and OH− ions can only pass through membrane hydrophilic pores, while ammonia can also dissolve in membrane matrix fragments not containing water and diffuse through these fragments. It is found that due to the Donnan exclusion of H+ ions as coions, the pH in the membrane internal solution increases when approaching the membrane side facing distilled water. Consequently, there is a change in the principal nitrogen-atom carrier in the membrane: in the part close to the side facing the feed NH4Cl solution (pH&lt;8.8), it is the NH4+ cation, and in the part close to distilled water, NH3 molecules. The concentration of NH4+ reaches almost zero at a point close to the middle of the membrane cross-section, which approximately halves the effective thickness of the diffusion layer for the transport of this ion. When NH3 takes over the nitrogen transport, it only needs to pass through the other half of the membrane. Leaving the membrane, it captures an H+ ion from water, and the released OH− goes towards the membrane side facing the feed solution to meet the NH4+ ions. The comparison of the simulation with experiment shows a satisfactory agreement.

Li₂MnO₃ is critical component in the well-studied Li-excess cathode materials xLi₂MnO₃•(1- x)LiMO₂ for achieving high lithium storage capacity. In this article, the diffusion of Li ions in Li₂MnO₃ is studied using molecular dynamics (MD) simulation with well-behaved empirical force fields obtained by fitting against the crystal structure from experiment and phonons calculated using Density Function Theory (DFT). We have found two possible tetrahedral hopping channels, 0-TM and 1-TM(Mn⁴⁺) channel, which are differentiated by the face sharing octahedral cations. Simulation results show that the 0-TM channel is active for Li hopping, while 1-TM(Mn4+) channel is inactive. During the delithiation process, the Li ions in the TM layered are firstly removed, then those in the Li layer. However, the Li ions will be trapped in the tetrahedral 0-TM channels as long as the four face sharing octahedral sites are cleared. Up to x=1.0 for Li₂-xMnO₃, almost all the Li ions are located at the tetrahedral sites, forming a regular array along a axis. The de-intercalation of tetrahedral Li ions requires a high voltage (>5.2 V vs. Li/Li+), limiting the practical capacities measured in lab. The diffusion of Mn ions into the Li layers is observed in a deeper delithiated structure (x=1.2 for Li₂-xMnO₃), indicating an initial phase transformation to a spinel-like structure. However, the Mn ions are mainly trapped in the tetrahedral sites in the Li layer, instead of the octahedral sites fin spinel-like structure. A few of Mn ions diffusing into the octahedral sites in Li layers have no face sharing tetrahedral Li ions, revealing a further Li de-intercalation is imperative for the complete phase transformation. Our model is not stable for x≥1.4 in Li₂-xMnO₃. Other charge compensation mechanism should be considered in this high delithiation stage, eg. oxygen release.

In this study, we focus on an abstract form of summation equations, which can be regarded as a particular class of nonlinear difference equations. We investigate sufficient conditions for the existence of discrete almost automorphic solutions by appealing to the fixed point theory and establish a linkage between the existence of discrete almost automorphic solutions and the existence of bounded solutions for the nonlinear difference equations in the spotlight. Consequentially, we propose a discrete counterpart of the Bohr-Neugebauer theorem for the qualitative theory of difference equations.

The widespread integration and growing dependence among currency, stock and commodity markets make these markets often very vulnerable to shocks and at risk of collapse at the same time. As a result, these trends threaten the sustainability of the entire financial system. In this study, we explore the spillovers and nonlinear dependences between the seven major foreign ex-change rates, crude oil and gold prices, a global stock price index, and oil and stock implied volatility indices as proxy variables for global risk factors by em-ploying directional spillover network approach. We also use multi-scale de-composition method and nonlinear causality test between these variables to capture multi-level relationships at short and long horizons. Major findings are summarized as follows. First, from the multi-scale decomposition analysis, we identify that Granger causality test results and the direction and strength of return spillovers change with the level of decomposition. Second, the results of nonlinear causality tests show variation in both the significance and direction of Granger causality relationships between the decomposed currency and other series at different timescales, especially for the decomposed oil, gold, and OVX series. Third, the measured directional spillover indices identify the EUR as the largest contributor of connectedness to the other series. The central role of the EUR is a net transmitter of connectedness to gold, oil, the GBP, JPY, and CHF.

The article is devoted to issues related to the propagation and transformation of vortexes in the optical range of frequency. Within the framework of the traditional and modified model of slowly varying envelope approximation (SVEA), the process of converting vortex beams of the optical domain into vortex beams of the terahertz radio range based on nonlinear generation of a difference frequency in a medium with a second-order susceptibility is considered. The modified SVEA splits a slowly varying amplitude into two factors, which makes it possible to more accurately describe the three-wave mixing process. The theoretical substantiation of the rule of vortex beams topological charges conversion is given – the topological charge of the output radio-vortex beam is equal to the difference between the topological charges of the input optical vortex beams. A numerical simulation model of the processes under consideration has been implemented and analyzed.

Hydrogel microneedles are a promising technology for the delivery of different types of medicines locally and painlessly, as well as ISF extraction. As the hydrogel microneedles are inserted into the tissue, they swell and release drugs. To improve the effectiveness of this technology in delivering medicine at controlled and desirable doses and intervals, a deep understanding of the mechanism of drug delivery inside the microneedles is required. In this work, drug diffusion inside a tapered microneedle is investigated using numerical simulation. The microneedle is divided into many small elements, and the mass transfer equation of meloxicam is solved in each element over time. The skin is simulated as the sink in the microneedle surface for drug absorption. Simulations are performed for different sizes of microneedles. For a microneedle with a height of 500 µm and a base diameter of 250 µm, the drug completely penetrates the skin within 3.2 seconds. The rate of drug diffusion from the tip of the microneedle is higher than diffusion from the side area near the microneedle base. The obtained data demonstrate that in addition to the height and the base diameter, the microneedle’s aspect ratio, h/d, also affects the time of drug diffusion. We present a nonlinear equation to predict the time of complete drug diffusion as a function of the microneedle geometrical parameter, including the height and base diameter. The proposed equation calculates the total drug diffusion time with an error of less than 7% for all studied cases. Predicting drug diffusion patterns inside microneedles can be helpful in the biomedical field, especially in the drug-controlled release system for the optimization of drug delivery.

This paper studies the spatial joint evolution of cooperative behavior and a partially assortative matching institution that protects cooperators. We consider cooperation as characterized by a cultural trait transmitted via an endogenous socialization mechanism a la Bisin and Verdier (2001) and we assume that such trait can diffuse randomly in space due to some spatial noise in the socialization mechanism. Using mathematical techniques from reaction-diffusion equations theory, we show that, under some conditions, an initially localized domain of preferences for cooperation can invade the whole population and characterize the asymptotic speed of diffusion. We consider first thecase with exogenous assortativeness, and then endogeneize the degree of social segmentation in matching, assuming that it is collectively set at each point of time and space by the local community. We show how relatively low cost segmenting institutions can appear in new places thanks to the spatial random diffusion of cooperation, helping a localized cultural cluster of cooperation to invade the whole population. The endogenous assortative matching institution follows a life cycle process : appearing, growing and then disappearing once a culture of cooperation is suffciently established in the local population.

Using a nonclassical symmetry of nonlinear reaction-diffusion equations, some exact multi-dimensional time-dependent solutions are constructed for a fourth-order Allen-Cahn-Hilliard equation. This models a phase field that gives a phenomenological description of a two-phase system near the critical temperature. Solutions are given for the changing phase of a cylindrical or spherical inclusion, allowing for a 'mushy zone' with mixed state that is controlled by imposing a pure state at the boundary. The diffusion coefficients for transport of one phase through the mixture, depend on the phase field value, since the physical structure of the mixture depends on the relative proportions of the two phases. A source term promotes stability of both of the pure phases but this tendency may be controlled or even reversed through the boundary conditions.

The particulars of stimulus-response experiments done on dynamic biosystems clearly limit what one can learn and validate about their structural interconnectivity (topology), even when collected kinetic output data are perfect (noise-free). As always, available access ports and other data limitations rule. For linear systems, exponential modes, visible and hidden, play an important role in understanding data limitations, embodied in what we call dynamical signatures in the data. We show here how to circumscribe and analyze modal response data in compartmentalizing model structures – so that modal analysis can be used constructively in systems biology model building – for nonlinear (NL) as well as linear biosystems. We do this by developing and exploiting the modal basis for dynamical signatures in hypothetical (perfect) input-output data associated with a structural model – one that includes inputs and outputs explicitly – and for NL as well as linear biosystems. The methodology establishes model dimensionality (size, complexity) from particular data sets; helps select among multiple candidate models (model distinguishability); helps in designing new experiments to extract “hidden” structure; and helps to simplify (reduce) models to their essentials. For NL biosystems, results are not as comprehensive, similarly informative about their dominant dynamical properties, and unified with linear models on invariant 2-dimensional manifolds in phase space. Some automation of these highly technical aspects of biomodeling is also introduced.

DGJ (Daftardar-Gejii-Jafaris) method is used to obtain numerical solution of the third order fractional differential equation. Providing the DGJ method converges, the approximate solution is a good and effective numerical result which is close to the exact solution or the exact solution. For this,the examples of the explaning the method are presented. The proposed method is implemented for the approximation solution of the third order nonlinear fractional partial differential equations. The method was shown to be unsuitable and inconsistent for an example of a nonlinear fractional partial differential equation depend on initial-boundary value conditions. The fact that these numerical results are not consistent can be explained by the fact that the method is not convergent.

Reliable fatigue design rules affect the proactive identification of safety parameters in aerospace industry. Numerous fatigue crack initiation and propagation models, linear and nonlinear, have been developed for designing purposes or estimation of the remaining life of aging airplanes. Depending on the adopted assumptions, the accuracy varies for different loading histories, loading types, and materials. Semi empirical models are simple but yield significant inaccuracies. Models with better theoretical basis provide better accuracy, but implementation in real conditions is problematic. In the present work, a review of author’s recent fatigue crack initiation and propagation models based on physical mechanisms is presented and improvements are proposed. Verification of the models on test results is provided and discussed.

Additive manufacturing processes offer various options to fabricate metal parts, which show numerous ecological and technological advantages compared to formative and subtractive manufacturing methods. Due to quick availability and high accuracy, they are particularly suitable to produce complex prototypes. Metal fused deposition modeling is a relatively new material extrusion additive manufacturing technique based on the widely used fused filament deposition process. This study focuses on the Inconel 625 metal filament from Markforged Inc., it consists of a mixture of metal powder and a binder system, the latter being removed during washing and sintering. In this article, the mechanical properties of printed and sintered Inconel were investigated using tensile testing specimens with three different infill patterns, solid, triangular, and gyroid, printed in flatwise and upright direction. In addition, investigations into the dimensional accuracy of the printed specimens and the sintering shrinkage were carried out. The results showed that neither the dimensional accuracy nor the sintering shrinkage was significantly influenced by the printing orientation. In the context of lightweight engineering, the structures proofed beneficial especially within the elastic region. Generally, triangular infill patterns resulted in higher stiffness, while gyroids led to more ductile specimens. A mass-related evaluation of tensile testing elucidates that with aid of the infill structures weight savings of 40 % resulted in mechanical performance decreased by only 20 % on average.

The interplay between Diffuse Idiopathic Skeletal Hyperostosis (DISH) and the gut microbiota represents a compelling area of research, offering insights into the relationship between spinal degenerative diseases and the gut's microbial inhabitants. This comprehensive review seeks to unravel the complex connection, shedding light on its implications for human health and potential therapeutic avenues. A crucial section dives into the world of gut microbiota (GM), exploring its impact on human health, featuring its defining characteristics, and highlighting its role in metabolism, immunomodulation, host interaction, and how its composition changes over time. The subsequent portion delves into the relationship between microbiome composition and pathological bone development, including the link between Intervertebral Disc Degeneration (IDD) and gut inflammation, emphasizing how gut inflammation and GM dysbiosis play pivotal roles. Further dissecting the interconnections, various axes of influence, including the gut-spine axis, gut-bone axis, gut-joint axis, gut-disc axis (specific to DISH), gut-ligament axis, and gut-muscle axis, are discussed. Of particular interest is the section on the impact of GM on DISH-derived pain, addressing a critical aspect of the condition's manifestation. The review discusses the potential of GM modulation as a treatment for DISH, providing hope for therapeutic advancements. Additionally, it highlights the positive impact of lifestyle interventions, such as dietary modifications, sleep optimization, and exercise regimens, in mitigating GM dysbiosis and potentially improving DISH outcomes. Lastly, the intriguing prospect of fecal microbiome transplant and its implications for DISH management is examined, opening new avenues for research and therapeutic interventions. In conclusion, this comprehensive review underscores the intricate interplay between DISH and the gut microbiota, offering a fresh perspective on the impact of GM on spinal degenerative diseases. It emphasizes the potential for innovative treatments, such as GM modulation and lifestyle interventions, and presents fecal microbiome transplant as an exciting area for future exploration.

Carbon fibers (CFs) cannot be directly used for the preparation of CF paper because of their chemically inert nature. Herein, the surface of CF was modified via the spontaneous oxidative self-polymerization of dopamine. By taking full advantage of the spontaneous oxidation and self-polymerization properties of PD to maintain the maximum strength of CFs, a polydopamine-modified CF paper (PDA-CFP) with excellent performance was prepared using PD-modified CFs (PDA-CFs), which increased the proportion of hydrophilic functional groups on the surface of carbon fibers, increased the O/C ratio on the CF surface by 6 times, and improved the bond strength between the modified CF and the adhesive by making full use of the interaction force between polydopamine and PVA fibers. In this way, the primary properties of the CF paper was improved. Overall, the results showed that the dispersion of CF was considerably improved by the dopamine modification. In addition, the primary physical properties of PDA-CFP were better than those of virgin CF paper (CFP-0). PDA-CFP exhibited a maximum tensile strength of 2.04 kN/m2, a minimum resistivity of 0.06055 Ω·cm and a minimum porosity of 72.4%. The tightness could be increased by up to 12.1%.

Lipid mesophases are being intensively studied as potential candidates for drug-delivery purposes. Extensive experimental characterization has unveiled a wide palette of release features depending on the nature of the host lipids and of the guest molecule, as well as on the environmental conditions. However, only few simulation works have addressed the matter, which hampers a solid rationalization of the richness of outcomes observed in experiments. Particularly, to date there are no theoretical works addressing the impact of hydropathy on the transport of a molecule within lipid mesophases, despite the significant fraction of hydrophobic molecules among currently-available drugs. Similarly, the high heterogeneity of water mobility in the nanoscopic channels within lipid mesophases has also been neglected. To fill this gap, we introduce here a minimal model to account for these features in a lamellar geometry, and systematically study the role played by hydropathy and water-mobility heterogeneity by Brownian-dynamics simulations. We unveil a fine interplay between the presence of free-energy barriers, the affinity of the drug for the lipids, and the reduced mobility of water in determining the net molecular transport. More in general, our work is an instance of how multiscale simulations can be fruitfully employed to assist experiments in release systems based on lipid mesophases.

Background. To describe the characteristics of anterior mediastinal masses on conventional magnetic resonance imaging (MRI) and to assess the role of the Apparent Diffusion Coefficient (ADC) value in distinguishing benign from malignant mediastinal lesions. Methods. We conducted a retrospective cross-sectional study on 55 patients with anterior mediastinal mass who performed MRI before treatment. Biopsy and histopathological assessments were done after that. A radiologist evaluates the changes of signal intensity on these sequences: T1- weighted VIBE DIXON pre and post-contrast with Gadolinium, T2 HASTE, T2 TIRM, DWI/ADC, to determine the size, margin of the lesion, the presence of fat, cystic in it. ADCs values were calculated from the ADC maps which were constructed from b = 0 and b = 2000 Results. The study was composed of 55 patients, with 5 benign lesions and 50 malignant lesions. The ADCmean, ADCmedian, ADC10, and ADC90 in the histogram-based approach and hot-spot-ROI-based mean ADC for the malignant lesions was significantly lower than those found in benign lesions (P-value <0.05). The hot-spot-ROI-based mean ADC had the highest value in differentiation between benign and malignant mediastinal lesions, between group A (benign lesions, thymoma A, AB, B1) and group B (thymoma B2, B3 and other malignant lesions). The cut-off point of the ADC value differentiating malignant from benign mediastinal lesions was 1,17x10-3mm2/s with sensitivity of 80%, and specificity of 80%. The cut off point of the ADC value differentiating group A from group B was 0.99 x10-3mm2/s with sensitivity of 78,4%, and specificity of 88.9%. The cut-off point of the ADC value differentiating lymphoma from other malignant lesions was 0,91 x10-3mm2/s with sensitivity of 100%, and specificity of 60.5%. Conclusion. Diffusion-weighted MRI and measurement of ADC value in histogram-based approach and hot-spot-ROI-based mean ADC are very helpful in the differentiation between benign and malignant anterior mediastinal lesions.

In this paper we introduce an ODE system to model the interaction between nature resources and human exploitation in a rich consumeristic society. In this model the rate of change of population depends on wealth per capita, and the rate of consumption has a quadratic growth with respect to population and wealth. As in our previous work \cite{BaCra_1}, we distinguish between renewable and non renewable resources, and we introduce a replenishment term for non renewable resources. We first get some information on the asymptotic behaviour of wealth and population, then we compute all the equilibria of the system and we study their stability when the parameter of exploitation of resources is small. Some numerical simulations confirm the theoretical results, and give suggestions for future research.

We introduce the linear subgroup of volume-preserving diffeomorphism as the underlying symmetry to construct an action within the effective field theory framework and the Schwinger-Keldish formalism. The formulated action is posited to effectively incorporate dissipative effects into the Navier-Stokes equations.

As a rapidly expanding family of two-dimensional (2D) materials, MXenes have recently gained considerable attention due to their appealing properties. Here, by developing a solution-based coating method that enables transfer-free and layer-by-layer film coating, we investigate the layer-dependent nonlinear optical absorption of Ti₃C₂T_x films ‒ an important member of the MXene family. By using the Z-scan technique, we characterize the nonlinear absorption of the prepared MXene films consisting of different numbers of monolayers. The results show that there is a strong and layer-dependent nonlinear absorption behavior, transitioning from revisable saturable absorption (RSA) to saturable absorption (SA) as the layer number increases from 5 to 30. Notably, the nonlinear absorption coefficient β varies significantly within this range, changing from ~7.13 × 10² cm/GW to ~-2.69 × 10² cm/GW. We also characterize the power-dependent nonlinear absorption of the MXene films at various incident laser intensities, and a decreasing trend in β is observed for increasing laser intensity. These results reveal the intriguing layer-dependent nonlinear optical properties of 2D MXene films, highlighting their versatility and potential for implementing high-performance nonlinear photonic devices.

Soft tactile sensors based on piezoresistive materials have various large-area sensing applications. However, their accuracy is often affected by hysteresis, a phenomenon that poses a significant challenge during operation. This paper introduces a novel approach that employs a backpropagation (BP) neural network to address the hysteresis nonlinearity in conductive fibre-based tactile sensors. To assess the effectiveness of the proposed method, four sensor units with different layer configurations (1, 3, 6, and 12) were designed. These sensor units underwent force sequences to collect corresponding output resistances. A backpropagation network was trained using these force sequences, thereby correcting the resistance values. The training process exhibited excellent convergence, effectively adjusting the network's parameters to minimize the error between predicted and actual resistance values. As a result, the trained BP network accurately predicted the output resistances. Several validation experiments were conducted to highlight the primary contribution of this research. The proposed method reduced the maximum hysteresis error from 24.2% of the sensor's full-scale output to 13.5%. This improvement establishes the approach as a promising solution for enhancing the accuracy of soft tactile sensors based on piezoresistive materials. By effectively mitigating hysteresis nonlinearity, the capabilities of soft tactile sensors in various applications can be enhanced. These sensors become more reliable and more efficient tools for force measurement and control, particularly in the fields of soft robotics and wearable technology. Consequently, their widespread applications extend to robotics, medical devices, consumer electronics, and gaming. Notably, the complete elimination of hysteresis in tactile sensors may not be feasible. Nevertheless, the proposed method effectively modifies the hysteresis nonlinearity, leading to improved sensor output accuracy.

This paper presents the common methods and corresponding drawbacks concerning nonlinear analysis of fluxgate excitation circuits and emphasizes the importance of nonlinear analysis for these circuits. With regard to the nonlinearity of the excitation circuit, this paper proposes the use of the core-measured hysteresis curve for mathematical analysis and the use of a nonlinear model that considers the coupling effect of the core and winding and influence of the historical magnetic field on the core for simulation analysis. The feasibility of mathematical calculations and simulation for the nonlinear study of fluxgate excitation circuit is verified via experiments. The results demonstrate that, in this regard, the simulation is better than a mathematical calculation. The simulation and experimental results of the excitation current and voltage waveforms under different excitation circuit parameters and structures are essentially consistent with each other, thereby verifying the effectiveness of the nonlinear excitation analysis method.

With correct dynamic system parameters (embodied in self-awareness statements), a controller can provide precise signals for tracking desired state trajectories. If dynamic system parameters are initially guessed incorrectly, a learning method may be used to find the correct parameters. In the deterministic artificial intelligence method, self-awareness statements are formed as mathematical expressions of the governing physics. When the nonlinear, coupled expressions are precisely parameterized as the product of known matrix components and unknown victrix (i.e., a regression form) tracking errors may be projected onto the known matrix to update the unknown victrix in an optimal form (in a two-norm sense). In this work, a modified learning method is proposed and proved to have global convergence of both state error and parameter estimation error. The modified learning method is compared with those in the prequels using simulation experiments of three-dimensional rigid body dynamic rotation motion. The modified approach is two magnitudes better than the methods in the prequels in terms of state error convergence.

Integrated photonic devices operating via optical nonlinearities offer a powerful solution for all-optical information processing, yielding processing speeds that are well beyond that of electronic processing as well as providing the added benefits of compact footprint, high stability, high scalability, and small power consumption. The increasing demand for high-performance nonlinear integrated photonic devices has facilitated the hybrid integration of novel materials to address the limitations of existing integrated photonic platforms, such as strong nonlinear optical absorption or an inadequate optical nonlinearity. Recently, graphene oxide (GO), with its large optical nonlinearity, high flexibility in altering its properties, and facile fabrication processes, has attracted significant attention, enabling many hybrid nonlinear integrated photonic devices with improved performance and novel capabilities. This paper reviews the applications of GO to nonlinear integrated photonics. First, an overview of GO’s optical properties and the fabrication technologies needed for its on-chip integration is provided. Next, the state-of-the-art GO nonlinear integrated photonic devices are reviewed, together with comparisons of the nonlinear optical performance of different integrated platforms incorporating GO. Finally, the challenges and perspectives of this field are discussed.

Cellular Nonlinear Networks (CNN) are a concept introduced in 1988 by Leon Chua and Lin Yang as a bio-inspired architecture, capable of massively parallel computation. Later on, CNN have been enhanced by incorporating designs that incorporate memristors to profit from their processing and memory capabilities. In addition, Stochastic Computing (SC) can be used to optimize the quantity of required processing elements; thus it provides a lightweight approximate computing framework, quite accurate and effective, though. In this work, we propose utilization of SC in designing and implementing a memristor-based CNN. As a proof of the proposed concept, an example of application is presented. This application combines Matlab and a FPGA in order to create the CNN. The implemented CNN has then been used to perform three different real-time applications on a 512x512 gray-scale and a 768x512 color image: storage of the image, edge detection, and image sharpening. It has to be pointed out that the same CNN has been used for the three different tasks, with the sole change of some programmable parameters. Results show an excellent capability with significant accompanying advantages, like the low number of needed elements further allowing for a low cost FPGA-based system implementation, something confirming the system’s ability for real time operation.

Backward electromagnetic waves are extraordinary waves with contra-directed phase velocity and energy flux. Unusual properties of the coherent nonlinear optical coupling of the phase-matched ordinary and backward electromagnetic waves with contra-directed energy fluxes are described which enable greatly-enhanced frequency and propagation direction conversion, parametrical amplification, as well as control of shape of the light pulses. Extraordinary transient processes that emerge in such metamaterials in pulsed regimes are described. The results of the numerical simulation of particular plasmonic metamaterials with hyperbolic dispersion are presented, which prove the possibility to match phases of such coupled guided ordinary and backward electromagnetic waves. Particular properties of the outlined processes in the proposed metamaterial are demonstrated through numerical simulations. Potential applications include ultra-miniature amplifiers, frequency changing reflectors, modulators, pulse shapers, and remotely actuated sensors.

In the paper, by virtue of techniques in combinatorial analysis, the authors simplify two families of nonlinear ordinary differential equations in terms of the Stirling numbers of the first kind.

Magnetic Nanoparticles (MNPs) is a promising technique to cure brain diseases. On the one hand, by serving as drug carriers, they can bypass the blood-brain barrier and deliver drug molecules to the brain parenchyma; on the other hand, their transport trajectory can be manipulated by applying an external magnetic field. However, due to the complex microstructure of brain tissues, e.g. the anisotropy of white matter (WM), how to achieve desired drug distribution patterns, e.g. uniform distribution, by tuning the drug delivery system is largely unknown. Here, in this study, by adopting a mathematical model capable of capturing the diffusion trajectories of MNPs in the microstructures, we systematically investigated the effects of key parameters in the MNPs delivery system on the equivalent diffusion coefficient of MNPs in the microenvironment of brain WM. The results show that uniform distribution of MNPs in anisotropic tissues can be achieved by adjusting the particle size and magnetic field. We have not only obtained a deeper understanding on how to optimise the MNPs delivery system, it can also be anticipated that an improved mathematical model could even help to achieve complex drug distribution patterns in the complicated brain environment by designing an appropriate combination of the key parameters.

We develop the process of discounting when underlying rates follow a jump-diffusion process, that is, when, in addition of diffusive behavior, rates suffer a series of finite discontinuities located at random Poissonian times. Jump amplitudes are also random and governed by an arbitrary density. Such a model may describe the economic evolution specially when extreme situations occur (pandemics, global wars, etc.). When between jumps the dynamical evolution is governed by an Ornstein-Uhlenbeck diffusion process, we obtain exact and explicit expressions for the discount function and the long-run discount rate and show that the presence of discontinuities may drastically reduce the discount rate, a fact that has significant consequences for environmental planning. We also discuss as a specific example the case when rates are described by the continous time random walk.

The work is devoted to the investigation of virus quasispecies evolution and diversification due to mutations, competition for host cells, and cross-reactive immune responses. The model consists of a nonlocal reaction-diffusion equation for the virus density depending on the genotype considered as a continuous variable and on time. This equation contains two integral terms corresponding to the nonlocal effects of virus interaction with host cells and with immune cells. In the model, a virus strain is represented by a localized solution concentrated around some given genotype. Emergence of new strains corresponds to a periodic wave propagating in the space of genotypes. The conditions of appearance of such waves and their dynamics are described.

We have investigated the canine of olive flounder in terms of the nonlinear optical signals of two-photon excitation autofluorescence (2PEF) and second harmonic generation (SHG), whereby two kinds of nonlinear microscope images of the canine were obtained using ~140 femtosecond pulses. For increasing excitation power of laser pulses, a photobleaching effect was found to be significant in the red and green ranges of autofluorescence, where a double-exponential decay of the intensity occurs within hundreds of second due to collagen fluorophores in the canine. In the blue range of autofluorescence, the photobleaching is suppressed due to an energy conversion of the incident laser pulse to SHG signal. As a result, the signal in blue range remains constant for long term exposure to laser. We have also found that the SHG intensity depends on the orienta-tion of linearly polarized excitation, and the optical anisotropy of SHG can be attributed to the collagen alignment of canines.

We examine a family of nonlinear q-difference-differential Cauchy problems obtained as a coupling of linear Cauchy problems containing dilation q-difference operators, recently investigated by the author, and quasi-linear Kowalevski type problems that involve contraction q-difference operators. We build up local holomorphic solutions to these problems. Two aspects of these solutions are explored. One facet deals with asymptotic expansions in the complex time variable for which a mixed type Gevrey and q-Gevrey structure is exhibited. The other feature concerns the problem of confluence of these solutions as q tends to 1.

Gol'denveizer's problem of a torus has been analyzed by Audoly and Pomeau (2002) and Sun (2021). However, all of the investigations of Gol'denveizer's problem of an elastic torus have been linear. In this paper, the finite element method is used to more accurately address this problem. Furthermore, Sun (2021) cannot be solved by nonlinear analysis. We research the nonlinear mechanical properties of Gol'denveizer's problem of circular and elliptic tori, and relevant nephograms are given. We study the buckling of Gol'denveizer's problem of an elastic torus, and propose failure patterns and force-displacement curves of tori in the nonlinear range. Investigations reveal that circular tori have more rich buckling phenomena as the parameter a increases. Gol'denveizer's problem of the buckling of an elliptic torus is analyzed, and we find a new buckling phenomenon called a "skirt." As a/b increases, the collapse load of an elliptic torus of the Gol'denveizer problem is enhanced gradually.

Bayesian nonlinear mixed effects models for data in the form of continuous, repeated measurements from a population, also known as Bayesian hierarchical nonlinear models, are a popular platform for analysis when interest focuses on individual specific characteristics and relevant uncertainty quantification. Due to the limitation of computational power, this framework was relatively dormant until the late 1980s, but in recent years, the statistical research community saw vigorous development of new methodological and computational techniques for these models, the emergence of software, and wide application of the models in numerous industrial and academic fields. This article presents an overview of the formulation, interpretation, and implementation of Bayesian nonlinear mixed effects models and surveys recent advances and applications.

This paper presents sufficient conditions for almost global stability of nonlinear switched systems consisting of both stable and unstable subsystems. Techniques from the stability analysis of switched systems have been combined with the multiple Lyapunov density approach - recently proposed by the authors for the almost global stability of nonlinear switched systems composed of stable subsystems. By using slow switching for stable subsystems and fast switching for unstable subsystems lower and upper bounds for mode-dependent average dwell times are obtained. In addition to that, by allowing each subsystem to perform slow switching and using some restrictions on total operation time of unstable subsystems and stable subsystems, we have obtained a lower bound for an average dwell time.

Principle of memristor presented by Leon Chua and time reversal based non-linear elastic wave spectroscopy (TR-NEWS) which can be applied to acoustic tomography are reviewed. Correlation of acoustic or electromagnetic nonlinear waves and its time reversed wave can produce strong signal. Materials like transducer or biological skin can be assumed to be composed of a large number of small elastic unit: hysteretic elementary unit (HEU), and one can take a HEU as a memristor whose operation depends on time. Relation between TR-NEWS and solitonic wave in fluid, and relation between decomposition of time reversal operator (DORT) and chaotic oscillation are discussed.

Nonlinear rheological properties of chiral crystal cholesteryl oleyl carbonate (COC) in blue phase III are investigated under different shear deformations; large amplitude oscillatory shear, step shear deformation, and continuous shear flow. Rheology of the liquid crystal is significantly affected by structural rearrangement of defects under shear flow. One of the examples on the defect-mediated rheology is the blue phase rheology. Blue phase is characterized by three dimensional network structure of the disclination lines. It has been numerically studied that the rheological behavior of the blue phase is dominated by destruction and creation of the disclination networks. In this study, we find that the nonlinear viscoelasticity of BPIII is characterized by the fracture of the disclination networks. Depending on the degree of the fracture, the nonlinear viscoelasticity is divided into two regimes; the weak nonlinear regime where the disclination network locally fractures but still show elastic response, and the strong nonlinear regime where the shear deformation breaks up the networks, which results in a loss of the elasticity. Continuous shear deformation reveals that a series of the fracture process delays with shear rate. The shear rate dependence suggests that force balance between the elastic force acting on the disclination lines and the viscous force determines the fracture behavior.

Abstract: The diffusion of competition under the coexistence of multi-generation products has become one of the important challenges faced by enterprises in their daily and sustainable operations. At the same time, the competition between different brands has intensified the difficulty and complexity of decision-making in the process of multi-generation product operation, Therefore, based on the Norton-Bass model diffusion process, this paper introduces two marketing variables, dynamic price and quality level, builds a multi-generation product diffusion model under the dual-brand competition, and analyzes the impact of the company's revenue on the launch time to market, pricing, quality or technical level. By using system dynamics (SD) method, From the perspective of strong brand and weak brand enterprises, the competition diffusion model is built and simulated. The simulation shows that: i) When enterprises have the same brand competitiveness, reducing the pricing level cannot obtain more revenue, but diminish the overall revenue of the industry; Raising the pricing level can get more revenue, but also improve the revenue of competitors. ii) When the competitive strength of enterprises is different, the strong brand tends to maintain a stable pricing on the basis of improving the quality level, or slightly raise the price. Weak brands tend to raise the pricing of new products significantly on the basis of improving the quality level. iii) The launch time to market decision of new product is influenced by the degree of product quality upgrade. Therefore, the frequency of releasing new products should trade-off against the degree of technological upgrading of product quality. This paper provides the theoretical basis and new insights for the new product launch and operation decision of enterprises.

Rapid solidification during metal additive manufacturing (AM) leads to non-equilibrium microsegregation, which can result in the formation of detrimental phases and cracking. Most of the microsegregation models, assume a Scheil-type solidification, where the solidification interface is planar and there exists local equilibrium at the interface along with either zero or infinite solute diffusion in the respective participating phases - solid and liquid. This assumption leads to errors in prediction. One has to account for finite solute diffusion and the curvature at the dendritic tip for more accurate predictions. In this work, we compare different microsegregation models that do and do not consider finite diffusion and dendrite tip kinetics against the experiments. We also propose a method to couple dendrite tip kinetics with the diffusion module (DICTRA®) implemented in Thermo-Calc®. The models which accounted for both finite diffusion and dendrite tip kinetics matched well with the experimental data.

We study an air-fluidized granular monolayer, composed in this case of plastic spheres, which roll on a metallic grid. The air current is adjusted so that the spheres never loose contact with the grid, so that the dynamics may be regarded as pseudo two-dimensional (or two-dimensional, if the effects of sphere rolling are not taken into account). We find two surprising continuous transitions, both of them displaying two coexisting phases. Moreover, in all cases, we found the coexisting phases display strong energy non-equipartition. In the first transition, at weak fludization, a glassy phase coexists with a disordered fluid-like phase. In the second transition, a hexagonal crystal coexists with the fluid phase. We analyze, for these two-phase systems, the specific diffusive properties of each phase, as well as the velocity correlations. Surprisingly, we find a glass phase at very low packing fraction and for a wide range of granular temperatures. Both phases are characterized also by a strong anti-correlated velocities upon collision. Thus, the dynamics observed for this quasi two-dimensional system unveils phase transitions with peculiar properties, very different from the predicted behavior in well know theories for their equilibrium counterparts.

We investigate entropy generation in unsteady three-dimensional axisymmetric MHD nanofluid flow over a non-linearly stretching sheet. The flow is subject to thermal radiation and a chemical reaction. The conservation equations were solved using the spectral quasi-linearization method. The novelty of the work is in the study of entropy generation in three-dimensional axisymmetric MHD nanofluid and the choice of the spectral quasilinearization method as the solution method. The effects of Brownian motion and thermophoresis are also taken into account when the nanofluid particle volume fraction on the boundary in passively controlled. The results show that as the Hartman number increases, both the Nusselt number and the Sherwood number decrease whereas the skin friction increases. It is further shown that an increase in the thermal radiation parameter corresponds to a decrease in the Nusselt number. Moreover, entropy generation increases with the physical parameters.

Cannabis is among the oldest human domesticates and has been subjected to intensive artificial (human-mediated) selection throughout history to create a wide array of varieties and biotypes for diverse uses, including fibre, food, biofuel, medicine and drugs. This paper briefly reviews the available literature on the taxonomy, evolutionary origin and domestication of this plant, as well as its worldwide dispersal, in both its wild and cultivated forms. Emphasis is placed on Europe and especially on the Iberian Peninsula. Today, it is accepted that Cannabis is a monospecific genus with two subspecies, C. sativa subsp. sativa and C. sativa subsp. indica, originating in Europe and Asia, respectively, by allopatric differentiation after geographic isolation fostered by Pleistocene glacial-interglacial cycles. Palynological and phylogeographic evidence situates the Cannabis ancestor on the NE Tibetan Plateau during the mid-Oligocene. The timing and place of domestication is still a matter of debate between contrasting views that defend single or multiple Neolithic domestication centres situated in different parts of the Eurasian supercontinent, notably central/southeastern China and the Caucasus region. Recent meta-analyses have suggested that wild Cannabis may have already been spread across Europe in the Pleistocene, and its domestication could have occurred during the European Copper/Bronze ages. According to the available reviews and meta-analyses, pre-anthropic dispersal of Cannabis into the Iberian Peninsula seems to have occurred only in postglacial times, and the earlier signs of cultivation date to the Early Medieval Ages. However, the palynological and archaeological evidence used to date is insufficient for a sound assessment, and the development of thorough Iberian databases to address further meta-analysis is essential for more robust conclusions. Some clues are provided for these achievements to be fulfilled.

We propose a new hierarchy of the vector derivative nonlinear Schr{\"o}dinger equations and consider the simplest multiphase solutions of this hierarchy. The study of the simplest solutions of these equations led to the following results. First, the three-leaf spectral curves $\Gamma=\{(\mu,\lambda)\}$ of the simplest multiphase solutions have a quite simple symmetry. They are invariant with respect to holomorphic involution $\tau$. The type of this involution depends on the genus of the spectral curve. Or the involution has the form $\tau:(\mu,\lambda)\to(\mu,-\lambda)$, or $\tau:(\mu,\lambda)\to(-\mu,-\lambda)$. The presence of symmetry leads to the fact that the dynamics of the solution is determined not by the entire spectral curve $\Gamma$, but by its factor $\Gamma/\tau$, which has a smaller genus. Secondly, it turned out that the dynamics of the two-component vector $\bp=(p_1,p_2)^t$ is determined, first of all, by the dynamics of its length $\abs{\bp}$. Independent equations determine the dependence of the direction of the vector $\bp$ from its length. In cases where the direction of the vector $\bp$ is fixed, the corresponding spectral curve splits into separate components. In conclusion, we note that, as in the case of the Manakov system, the equation of the spectral curve is invariant with respect to the orthogonal transformation of the vector solutions. I.e., the solution can be found from the spectral curve up to the orthogonal transformation. This fact indicates that the spectral curve does not depend on the individual components of the solution, but on their symmetric functions. Thus, the spectral data of multiphase solutions have two symmetries. These symmetries make it difficult to reconstruct signals from their spectral data. The work contains examples illustrating these statements.

In the last years, a recent growing line of research has been developed with fruitful results by using fractional and conformable derivatives in the iterative procedures of classical methods for solving nonlinear equations. In that sense, the use of conformable derivatives has shown better behavior than fractional ones, not only in the theory, but also in the practice. In this work, we adapt the approximation of conformable derivatives in order to design the first conformable derivative-free iterative schemes to solve nonlinear equations: a Steffensen’s type method and a Secant type method; the latter with memory. Convergence analysis is made, preserving the order of classical cases, and the numerical performance is studied in order to confirm the results in the theory. It is shown that these methods can present some numerical advantages versus their classical partners, with wide sets of converging initial estimations.

An exact spherically symmetric and magnetically charged black hole solution in 4D Einstein-Gauss-Bonnet gravity coupled to nonlinear electrodynamics (NED) is obtained. The NED Lagrangian is given by ${\cal L}_{NED} = -{\cal F}/(1+\sqrt[4]{2\beta{\cal F}})$, where ${\cal F}$ is the field invariant. We study the thermodynamics calculating the Hawking temperature and the heat capacity of the black hole. The phase transitions take place when the Hawking temperature has an extremum and the heat capacity is singular. We demonstrate that black holes are thermodynamically stable in some range of event horizon radii where the heat capacity is positive. The BH shadow radii are calculated. It is shown that when increasing the nonlinearity parameter $\beta$ the BH shadow radius is decreased.

Our earlier work has tentatively shown that the hierarchy of fermion masses and mixing angles follows from the universal behavior of nonlinear dynamics. In this brief sequel we survey a similar scenario in which the Cabibbo angle arises from the nonlinear dynamics of charged-current interactions.

The necessary and sufficient conditions of existence of the nonlinear operator equations' branches of solutions in the neighbourhood of branching points are derived. The approach is based on reduction of the nonlinear operator equations to finite-dimensional problems. Methods of nonlinear functional analysis, integral equations, spectral theory based on index of Kronecker-Poincare, Morse-Conley index, power geometry and other methods are employed. Proposed methodology enables justification of the theorems on existence of bifurcation points and bifurcation sets in the nonstandard models. Formulated theorems are constructive. For a certain smoothness of the nonlinear operator, the asymptotic behaviour of the solutions is analysed in the neighbourhood of the branch points and uniformly converging iterative schemes with a choice of the uniformization parameter enables the comprehensive analysis of the problems details. General theorems are illustrated on the nonlinear integral equations.

In the present work we study the existence of solutions for hybrid nonlinear fractional integrodifferential equations. We developed an algorithm by using the operator theoretical techniques in order to obtain the approximate solutions. The main results depend on the Dhage iteration method that were incorporated with the modern hybrid fixed point theorems. The approximate solutions were obtained by using Lipschitz conditions and weaker form of mixed partial continuity. Further, we provide some examples to explain the hypotheses and the related results.