The Ultra-Cold Neutron (UCN) source being commissioned at North Carolina State Universityâs PULSTAR reactor is uniquely optimized for UCN production in the former graphite-filled thermal column outside of the reactor pool. The source utilizes a remote moderation design which is particularly well suited to the PULSTAR reactor on account of its large thermal and epithermal neutron leakage from the core face. This large non-equilibrium flux from the core is efficiently transported to the UCN source through the specially designed beam port in order to optimize UCN production at any given reactor power. The increased distance to the source from the core also greatly limits the heat load on the cryogenic system. A MCNP model of this system was developed and is in good agreement with gold foil activation measurements using a mock-up setup as well as with the real UCN source heavy water moderator. These results established a firm baseline for estimates of the cold neutron flux available for UCN production and prove that remote moderation in a thermal column port is a valuable option for future designs of cryogenic UCN sources.

This work (in two parts) will review the recently developed predictive modeling methodology called “4th-BERRU-PM” and its applicability to energy systems as exemplified by an illustrative application to the Polyethylene-Reflected Plutonium (acronym: PERP) OECD/NEA reactor physics benchmark. The acronym 4th-BERRU-PM designates the “Fourth-Order Best-Estimate Results with Reduced Uncertainties Predictive Modeling” methodology, which yields best-estimate results with reduced uncertainties for the first fourth-order moments (mean values, covariance, skewness, and kurtosis) of the optimally predicted posterior distribution of model results and calibrated model parameters. The 4th-BERRU-PM uses the Maximum Entropy (MaxEnt) principle to incorporate fourth-order experimental and computational information, including fourth (and higher) order sensitivities of computed model responses to model parameters, thus incorporating, as particular cases, the results previously predicted by the second-order predictive modeling methodology 2nd-BERRU-PM, and vastly generalizing the results produced by extant data assimilation and data adjustment procedures. The 4th-BERRU-PM methodology encompasses the scopes of high-order sensitivity analysis (SA), uncertainty quantification (UQ), data assimilation (DA) and model calibration (MC). The application of the 4th-BERRU-PM methodology to energy systems is illustrated by means of the above-mentioned OECD/NEA reactor physics benchmark, which is modeled using the neutron transport Boltzmann equation involving 21976 imprecisely known parameters, the solution of which is representative of “large-scale computations.” The model result (“response”) of interest is the leakage of neutrons through the outer surface of this spherical benchmark, which can be computed numerically and measured experimentally. Part 1 of this work illustrates the impact of high-order sensitivities, in conjunction with parameter standard deviations of various magnitudes, on the determination of the expected value and variance of the computed response in terms of the first four moments of the distribution of the uncertain model parameters. Part 2 of this work will illustrate the capabilities of the 4th-BERRU-PM methodology for combining computational and experimental information, up to and including forth-order sensitivities and distributional moments, for producing best-estimate values for the predicted responses and model parameters while reducing their accompanying uncertainties.

Computationally modelling a nuclear reactor startup core for a benchmark against the existing models is highly desirable for an independent assessment informing nuclear engineers and energy policymakers. This work presents a startup core model of the UK’s first Evolutionary Pressurised Water Reactor (EPR) based on Monte Carlo simulations of particle collisions using Serpent 2, a continuous-energy Monte Carlo reactor physics burnup code. Coupling between neutronics and thermal-hydraulic conditions with the fuel depletion is incorporated into the multi-dimensional branches, obtaining the thermal flux and fission rate (power) distributions radially and axially from the three dimensional (3D) single assembly level to a 3D full core. Shannon entropy is employed to characterise the convergence of the fission source distribution, with 3 billion neutron histories tracked by parallel computing. Source biasing is applied for the variance reduction. Benchmarking the proposed Monte Carlo 3D full-core model against the traditional deterministic transport computation suite used by the UK Office for Nuclear Regulation (ONR), a reasonably good agreement within statistics is demonstrated for the safety-related reactivity coefficients, which creates trust in the EPR safety report.

Farmers today are using biochemical treatments to improve their crop yields. Commercialized organic biostimulants exist in the form of pyroligneous acid generated by burning agricultural waste products. During the 2023 growing season we demonstrated that soil treatment with a commercial pyroligneous acid product, Coriphol™, manufactured by Corigin Solutions, Inc., stimulated plant growth and significantly improved yield with an optimal treatment dose of 2 gal./acre. In the present work we examined the effect of this treatment on soybean nutritional content using seed harvested from the 2023 season. Total mean seed protein content for untreated control plants was 32.26 ± 0.49% of dry mass and increased 10.8% to 35.64 ± 0.64% with treatment. This increase resulted in a net reduction in total free amino acid content although levels of the es-sential dietary amino acid, lysine, were boosted 6-fold. Total lipid content was unaffected by treatment with mean levels of 21.61 ± 0.70% of dry mass noted. Treatment, however, reduced saturated fatty acid content by roughly 40% while reducing the polyunsaturated content of linoleic acid in favor of the monounsaturated fatty acid, oleic acid. Finally, Coriphol™ treatment did not impact seed content of eight essential micronutrients including Na, Mg, K, Ca, Fe, Ni, Cu and Mo, but did significantly boost Zn and Mn levels. Altogether, these results demonstrate that soil treat-ment with the growth stimulant Coriphol™ has the potential to improve the dietary nutritional value of soybean.

Dhaka one of the fastest-growing megacities in the world is increasingly vulnerable to urban flooding due to rapid urbanization, inadequate drainage infrastructure, and climate change-induced extreme weather events. This study presents the development of an urban flood forecasting system for Dhaka City using the MIKE+ hydrodynamic modeling software. The system integrates detailed hydrological and hydraulic models to simulate urban flooding scenarios, accounting for complex drainage networks and catchment characteristics. Real-time data from river gauges, rainfall stations, and drainage systems are incorporated to enhance the accuracy and reliability of the forecasts. The model's predictive capability is validated against historical flood events, demonstrating its effectiveness in forecasting flood extents, depths, and durations in critical areas of the city. This system serves as a valuable tool for city planners, emergency response teams, and decision-makers, enabling proactive flood management and risk mitigation. The study underscores the importance of such advanced modeling tools in safeguarding urban populations and infrastructures from the increasing threat of urban floods in Dhaka and similar rapidly urbanizing cities.

Calcium and magnesium are important not only for human health, but also for reducing problems related to the corrosive and aggressive effects of soft water on drinking water distribution materials. Experimental and mathematical modeling of the recarbonization process aimed at increasing the content of these biogenic elements in water was carried out using the novelty of a continuous laboratory and pilot scale fluidized bed reactors. Water remineralization using half-calcined dolomite (HCD) and carbon dioxide was used. The influence of operating conditions Q(CO2), freshwater inflow and HCD dose on quality indicators of treated drinking water (c(Ca2+), c(Mg2+), c(Ca2++Mg2+) and Ca/Mg) was studied. The results show that the concentration of Mg2+ is more significantly affected by the amount of HCD in the system and the flow of CO2. The influence of freshwater inflow on the Mg2+content is to a lesser extent. At a constant CO2 flow, therefore, as the tap water inflow increases, the Ca2+ content decreases and the Mg2+ content increases, which has results in a decrease in the Ca/Mg molar ratio. However, the Ca/Mg ratio can be effectively controlled by adding an appropriate amount of HCD at certain time intervals. Overproduction of ions is easily controlled by CO2 flow.

Pretreatment of cells with proteolysis inhibitors diminished intensity and changed shape of DNICs specific EPR signal in a treatment time-dependent manner. The level of DNIC formation was significantly influenced by the presence of protein degradation products. Interestingly, formation of HMWDNICs depended on the availability of LMWDNICs. The extent of glutathione involvement in the in vivo formation of DNICs is minor yet noticeable, aligning with our prior research findings.

Estimating parameters for multiple datasets can be time consuming, especially when the number of datasets is large. One solution is to sample from multiple datasets simultaneously using Bayesian methods such as adaptive multiple importance sampling (AMIS). Here we use the AMIS approach to fit a von Misses distribution to multiple datasets for wind trajectories derived from a Lagrangian Particle Dispersion Model driven from a 3D meteorological data. The primary objective is to characterise the uncertainties in wind trajectories in a form that can be used as inputs for predictive models of wind-dispersed insect pests and pathogens of agricultural crops for use in evaluating risk and in planning mitigation actions. Our results show that AMIS can significantly improve the efficiency of parameter inference for multiple datasets.

This work continues the review and illustrative application to energy systems of the “Fourth-Order Best-Estimate Results with Reduced Uncertainties Predictive Modeling” (4th-BERRU-PM) methodology. The 4th-BERRU-PM methodology uses the Maximum Entropy (MaxEnt) principle to incorporate fourth-order experimental and computational information, in-cluding fourth (and higher) order sensitivities of computed model responses with respect to model parameters. The 4th-BERRU-PM methodology yields the fourth-order MaxEnt posterior distribution of experimentally measured and computed model responses and parameters, in the combined phase-space of model responses and parameters. The 4th-BERRU-PM methodology encompasses fourth-order sensitivity analysis (SA) and uncertainty quantification (UQ), which were reviewed in the accompanying work (Part 1), as well as fourth-order data assimilation (DA) and model calibration (MC) capabilities, which will be reviewed and illustrated in this work (Part 2). The applicability of the 4th-BERRU-PM methodology to energy systems is illustrated by using the Polyethylene-Reflected Plutonium (acronym: PERP) OECD/NEA reactor physics benchmark, which is modeled using the linear neutron transport Boltzmann equation, involving 21976 im-precisely known parameters. This benchmark is representative of “large-scale computations” such as those involved in the modeling of energy systems. The result (“response”) of interest for the PERP benchmark is the leakage of neutrons through the outer surface of this spherical benchmark, which can be computed numerically and measured experimentally. The impact of the high-order sensitivities of the response with respect to the PERP model parameters is quantified for “high-precision” parameters (2% standard deviations) and “medium-precision” parameters (5% standard deviations). Analyzing the best-estimate results with reduced uncertainties for the 1st- through 4th-order moments (mean values, covariance, skewness, and kurtosis) produced by the 4th-BERRU-PM methodology for the PERP benchmark indicates that, even for systems mod-eled by linear equations (e.g., the PERP benchmark), retaining only first-order sensitivities is insufficient for reliable predictive modeling (including SA, UQ, DA, MC). At least second-order sensitivities should be retained in order to obtain reliable predictions.

The studied solar pot is a recent invention, which gained a utility model protection in 2021 from the Hungarian Intellectual Property Office under patent number 5489. The device is made for environmentally friendly cooking or heating (by utilizing solar energy) of foods and liquids. Its structure is similar to a double pipe heat exchanger, it has an outer mantle and an inner cooking tank. The goals of the paper are proposing a new physically-based mathematical model describing the solar pot and carrying out computer experiments with it, assembling an experimental system of the pot connected with a solar collector and performing measurements on it. Based on the results, the solar pot can successfully be used for cooking or sterilizing foods or liquids during the studied time period, in Hungary.

The licensing of new reactors implies the use of verified and validated neutronics codes. Numerical validation can rely on sensitivity and uncertainty studies but they require repeated execution of time-consuming neutron flux and depletion calculations. The computational costs can be shortened by using perturbation theories. However, Depletion Perturbation Theory is restricted to single integral values such as a nuclide density. Relying on reduced basis approaches, which reconstruct the whole nuclide densities at once, is one way to get around this restriction. Furthermore, the adjoint-based reduced-order model uses the direct and adjoint equations for the projection. For diffusion or transport calculations, Exact-to-Precision Generalized Perturbation Theory has been developed. Still, no models for depletion calculations are readily available. Therefore, this paper describes a novel adjoint-based reduced order model for the Bateman equation. It uses a range-finding algorithm to create the basis and the Depletion Perturbation Theory for the reconstruction of the nuclide densities at first order. Our paper shows that for several perturbed cases, the depletion reduced-order model successfully reconstructs the nuclide densities. As a result, this serves as a proof of concept for our adjoint-based reduced order model which can perform sensitivity and uncertainty burn-up analysis in a shorter time.

The rapid and accurate detection of viruses and the discovery of single nucleotide polymorphisms (SNPs) are crucial for disease management and understanding viral evolution. In this study, a pipeline for virus detection, validation, and SNP discovery from next-generation sequencing (NGS) data is presented. By integrating state-of-the-art bioinformatics tools with artificial intelligence, the pipeline processes raw sequencing data to identify viral sequences with high accuracy and sensitivity. Before aligning the reads to the reference genomes, quality control measures and adapter trimming are performed to ensure the integrity of the data. Unmapped reads are subjected to de novo assembly to reveal novel viral sequences and genetic elements. The effectiveness of the pipeline is demonstrated by the identification of virus sequences, illustrating its potential for the detection of known and emerging pathogens. SNP discovery is performed using a custom Python script that compares the entire population of sequenced viral reads to a reference genome. This approach provides a comprehensive overview of viral genetic diversity and identifies dominant variants and a spectrum of genetic variations. The robustness of the pipeline is confirmed by the recovery of complete viral sequences, which improves our understanding of viral genomics. This study highlights the synergy between traditional bioinformatics techniques and modern approaches, providing a robust tool for analyzing viral genomes and contributing to the broader field of viral genomics.

Determining the estrous cycle stages in mice is essential for optimizing breeding strategies, synchronizing experimental time lines, and facilitating studies in behavior, drug testing, and genetics. It is critical for reducing the production of genetically unmodified offspring in the generation and investigation of genetically modified animal models. An accurate detection of the estrus cycle is particularly relevant in the context of the 3Rs—Replacement, Reduction and Refinement. The estrous cycle, encompassing the reproductive phases of mice, is key to refining experimental designs and addressing ethical issues related to the use of animals in research. This study presents results from two independent laboratories on the efficacy of the Mouse Estrus Detector (MED) from Elmi Ltd. (Latvia) for the accurate determination of the estrus phase. The female mice of five strains/stocks (CD1, FVB/N, C57Bl6/J, B6D2F1, and Swiss) were used. The results showed that the MEDProTM is a low -traumatic, simple, rapid and painless method of estrus detection that supports the principles of the 3Rs. The use of the MEDProTM for estrus detection in mice caused minimal stress, enhanced mating efficiency, facilitated an increase in the number of embryos for the in vitro fertilization and allowed the production of the desired number of foster animals.

Lap joints were friction stir welded in AA 7075-T6 at 1320 rpm and using two welding speeds: 70 mm/min and 120 mm/min. The temperature profiles of the weld zone were registered during the process; furthermore, the microhardness, tensile strength, and microstructure of the joints produced were examined. This study brings new insights into the thermomechanical behavior of the material during the process. The peak temperature obtained with the lower welding speed (70 mm/min) is 10% higher than that obtained with the higher speed (120 mm/min). Moreover, a 5% increase in microhardness and a 6% increase in tensile strength were were observed increasing the welding speed. Addition-ally, the microstructure examination demonstrated that, by decreasing the welding speed, the larger interaction between the tool and the material results in a deeper stir zone due to the increased heat diffusion downwards to the material. This heat flow affects the thermal profile and influences the resulting mechanical properties of the welded joints.

Previous high throughput screening studies indicated trans-eQTLs tend to be tissue specific. In this study, I probed if this feature can be used to identify tissue-specific gene regulatory networks. eQTL data (P<5e-8) for 16,259 genes were identified and their summary association statistics were obtained from the eQTLGene database. Next, eQTLs that display both cis and trans regulatory effects were selected and the association between their corresponding genes were examined using Mendelian randomization. A total of 169 genes that exerted trans-regulatory impacts on 692 genes were identified. 90% of the genes (N=749) aggregated into a gene regulatory network significantly enriched in hemo-immune processes. The robustness of finding was confirmed through simulation. The identified network displayed the scale-free topology. This provided the reason to examine the association of the network’s hub genes with the phenome. The outcome of analyses revealed GSDMB and ORMDL3 impact several disorders of immune origin and ALDH2 overexpression contributes to obesity. This study reports trans-eQTLs can be used to identify tissue-specific gene regulatory networks and describes a workflow to achieve this purpose. The network identified in this study showed scale-free topology indicating the hub genes of a GRN could be targeted to prevent disease outcomes.

The presented work offers a novel process scheme for valorizing historical Pb-Zn slag, which involves crushing, grinding, and then using separation techniques to concentrate valuable components (nonferrous metals). This methodology could have a significant impact on the global beneficiation of metallurgical slags since, in theory, it is significantly more simple, environmentally friendly, and cost-effective than standard pyrometallurgical or hydrometallurgical procedures. According to previous physicochemical and mineralogical studies, Pb-Zn slag from "Topilnica" Veles is a valuable secondary raw material. This inhomogeneous technogenic resource contains substantial amounts of nonferrous metals (Pb, Zn, Cu, and Ag). However, laboratory tests have indicated that the Pb-Zn slag contains a very uneven valuable metals amounts, ranging from several g/ton to several tens of g/ton. The main issue is that traditional metallurgical procedures for releasing beneficial elements are not commercially viable since the valuable elements are "trapped" within amorphous aluminosilicates or intergrowths of alloy grains and glassy phases. Gravity concentration (Wilfley 13 shaking table) and magnetic separation (Davis separator and disk separator) were used to obtain the final concentrate following comminution and grindability testing. The gravity concentration proved more effective. This streamlined approach of valorizing Pb-Zn slag can reduce the need for hazardous chemicals used in hydrometallurgical refinement operations, as well as the extremely high temperatures required for pyrometallurgical processing. This is the first investigation into the feasibility of this novel approach, which includes direct investigations of the Pb-Zn slag feed using these alternative technologies. After extracting the valuable metals, the amorphous aluminosilicate part of the Pb-Zn slag can be reapplied as an alternative raw material in the building sector, adding to the circularity of the suggested approach..

Using analysis methods such as Rutherford backscattering Spectrometry, scanning electron microscopy, X-ray diffraction, and Raman spectroscopy, the diffusion behavior of iodine in micro/nano-porous graphite under high-temperature conditions was studied. The results indicate that iodine diffusion leads to the contraction of graphite microcrystals, a decrease in interlayer spacing, and an increase in defect density, resulting in a reduction in microcrystal size. Upon diffusion of iodine out of iodine-loaded graphite, the microcrystal size of the graphite increases, the interlayer spacing appears to return to the initial state, and the defect density decreases. By comparing the iodine diffusion performance of nanoporous graphite G400 and G450 with microporous graphite G500, it was determined that nanoporous graphite exhibits better inhibition of iodine diffusion compared to microporous graphite. Studying the diffusion behavior of iodine in micro/nano-porous graphite has significant academic significance and engineering value for the screening, design, and performance optimization of nuclear graphite.

Continuous-wave photocathode guns are capable of delivering electron beams with high repetition rates and high average currents. However, they are limited by relatively low accelerating gradients and cathode fields. This limitation leads to a larger beam size at the gun exit due to space charge forces, making the beam more sensitive to optical aberrations and posing challenges for low-emittance electron beam transmission. This paper focuses on the aberrations induced by multipole fields. We analyze the effects of quadrupole, sextupole, and higher-order fields on beam profile and transverse emittance and propose a beam-based method for the rapid characterization and correction of these multipole fields. Furthermore, we present an experimental study conducted on the DC-SRF-II photocathode gun equipped with dedicated correctors. Both simulation and experimental results demonstrate that our approach effectively mitigates beam aberrations caused by multipole fields, resulting in improved beam symmetry and reduced emittance.

PET imaging of bacterial infection could potentially provide added benefit for patient care by non-invasive means. [68Ga]Ga-desferrioxamine B – a radiolabelled siderophore – shows specific uptake by human-pathogenic bacteria like Staphylococcus aureus or Pseudomonas aeruginosa as well as sufficient serum stability for clinical application. Here, we provide data for automated production of [68Ga]Ga-desferrioxamine B on two different cassette based synthesis modules (Modular-Lab PharmTracer and GRP 3V) using commercially available cassettes together with an approved 68Ge/68Ga radionuclide generator. Quality control including determination of radiochemical purity as well as a system suitability test was set up via RP-HPLC on a C18 column. The two described production processes, using an acetic acid/acetate buffer system with ascorbic acid as a radiation scavenger for radiolabelling, yield ready-to-use formulations with sufficient activity yield. Batch data showed radiochemical purity of &gt;95 % as determined by RP-HPLC and ITLC as well as excellent stability over 2 hours post production. Specifications for routine production were set up and validated with four master batches for each synthesis module. Based on this study, an academic clinical trial for imaging of bacterial infection was initiated. Both described synthesis methods enable reproducible, automated in-house production of [68Ga]Ga-desferrioxamine B for clinical application.

Background: G6PD is a rate-limiting enzyme of the pentose phosphate pathway. The loss of G6PD activity in red blood cells exposes to the risk of acute haemolytic anaemia under oxidative stress, induced by infections, some medications, or fava beans. More than 200 single missense mutations are known in the G6PD gene. This study reports a 41-year-old woman coming from Basilicata region (Italy) that carried out the G6PD status in our hospital for prenatal investiga-tions. Methods: DNA was extracted from peripheral blood sample and genotyped for common-est G6PD pathogenic variants (PVs). Positive results obtained by Restriction Fragment Length Polymorphism (RFLP), as per practice in our laboratory, are then re-confirmed in Sanger se-quencing. Results: RFLP analysis highlighted a variant compatible with G6PD Cassano variant. Confirmatory testing by Sanger unexpectedly identified a novel variant: c.1357G>A, p.(Val453Met) (NM_001360016.2). In silico models predicted a deleterious effect of this variant at the protein level. The novel G6PD variant was named "G6PD Potenza", on the basis of the pa-tient's regional origin. Conclusion: This case describes a novel G6PD variant. It also highlights how the Sanger sequencing technique still represents an indispensable confirmatory standard method for variants that could be miss-interpreted by using of “first-level” approached, as the RFLP. We stress that the evaluation of clinical manifestations in G6PD deficient patients is of primary importance for the classification of each new G6PD mutation, in agreement with the new WHO guidelines.

This paper proposes a novel facial expression recognition network called the Lightweight Facial Network with Spatial Bias (LFNSB). The LFNSB model balances model complexity and recognition accuracy. It has two key components: a lightweight feature extraction network (LFN) and a Spatial Bias (SB) module for aggregating global information. The LFN introduces combined channel operations and depthwise convolution techniques, effectively reducing the number of parameters while enhancing feature representation capability. The Spatial Bias module enables the model to focus on local facial features while also capturing the dependencies between different facial regions. Additionally, a novel loss function called Cosine-Harmony Loss is designed. This function optimizes the relative positions of feature vectors in high-dimensional space, resulting in better feature separation and clustering. Experimental results on the AffectNet and RAF-DB datasets show that the proposed LFNSB model performs excellently in facial expression recognition tasks. It achieves high recognition accuracy while significantly reducing the number of parameters, thus substantially lowering model complexity.

The physical properties of a structure such stiffness although can be determined by some statical tests, the identification of damping parameter requires a dynamic test. In general, both theoretical prediction and experimental identification of damping are quite difficult. There are many different techniques available for damping identification, and each method gives a different damping parameter. The dynamic indentation method, rheometry, atomic force microscopy, and resonant vibration tests are commonly used to identify the damping of materials, including soft materials. While the viscous damping ratio, loss factor, complex modulus and viscosity are quite common to describe damping of materials, there are also other parameters such as the specific damping capacity, loss angle, half-power bandwidth, and logarithmic decrement to describe damping of various materials. Often one of these parameters is measured in practical applications and the measured damping parameter needs to be converted into another damping parameter for comparison purposes. In this review, the theoretical derivations of different parameters for the description and quantification of damping and their relationships, and the methods for damping identification are presented. The expressions for both high damping and low damping are included and evaluated. This paper could be a primary resource for damping research and teaching.

Computational methods are essential to support and advance nuclear technologies due to the hazards of handling and analysing highly radioactive materials such as spent nuclear fuel (SNF). However, many such methods, including those thatcan predict SNF compositions and decay heat parameters, require expensive, proprietary software, alongside significant programming experience and computational power for utilisation, severely limiting availability of data and hampering research throughput. Although some datasets are available, many are incomplete or only cover certain fuel systems for older reactor types. Research investigating new methods for SNF recycling, for example, requires compositional and decay heat data for fuel systems not covered by extant data, though analogous source data may be available. With this in mind, we have developed a simple, accessible, and flexible method for extrapolation of isotopic, elemental, and decayheat compositions for SNF at discharge and following decay storage before recycling, based on an extant dataset. This semi-empirical method uses physical and mathematical first principles and can be performed using software accessible to all researchers. This provides outputs accurate to within 1% of reference values interpolated within the range of available data for isotopic compositions, with sensible extrapolations at higher burnups beyond those reported, withoverall elemental outputs accurate to within 0.1%of expected totals. In this publication, we present the developmental methodology, some sample data, the present limitations, and options for future development and expansion of functionality.

MicroRNAs are small non-coding RNAs, which contribute to the regulation of many physiolog-ical and pathological processes. Conventionally, miRNAs perform their activity in the cyto-plasm, where they regulate gene expression by interacting in a sequence-specific manner with mature messenger RNAs. Recent studies point to the presence of mature miRNAs in the nucleus. This review summarizes current findings regarding the molecular activities of nuclear miRNAs. These molecules can regulate gene expression at the transcriptional level by directly binding DNA on the promoter or the enhancer of regulated genes. MiRNAs recruit to these regions dif-ferent protein complexes, resulting both in activation or repression of transcription, through a number of molecular mechanisms. Haematopoiesis is presented as a paradigmatic biological process whereby nuclear miRNAs possess a relevant regulatory role. Nuclear miRNAs may af-fect gene expression also acting on nuclear mRNA processing and on the biogenesis of miRNA themselves by regulating pri-miRNA maturation. Overall, nuclear miRNAs are biologically ac-tive molecules that can be critical for the fine tuning of gene expression and deserve further studies in a number of physiological and pathological conditions

Certain micronutrients exhibit immunomodulatory effects. However, no intervention has yet investigated the effect of an individualized supplementation on the severity of upper respiratory tract infections (URI). Therefore, we investigated whether a personalized supplementation moderates the incidence and severity of URI. Selenium, zinc, and vitamin D was measured from 59 healthy participants ) in dried blood spots. Accordingly, a personalized supplement was provided with or without the respective micronutrients. We used WURSS-21 questionnaires to assess the disease status. The blood values converged during the intervention and micronutrients no longer differed at the end of the intervention period between treated and untreated volunteers. The incidence and severity of the illness did not significantly differ between the groups. However, when analyzing the WURSS-21 score by the intention to treat, the initially randomized treatment arm revealed a significantly higher score than the placebo arm. Upon acute administration, individualized combination of selenium, zinc and vitamin D does not reduce the number or contribute to a milder course of URIs. Therefore, supplementation in acute infectious situations seems questionable. Further studies must address the habitual diet in more detail to better understand the impact of individual micronutrient status on the prevention of URI.

Kisspeptin (KISS1) and its cognate receptor (KISS1R) are implicated in the progression of various cancers. However, a theranostic radiopharmaceutical targeting the KISS1 receptor (KISS1R) has yet to be explored. A gallium-68 labelled kisspeptin-10 (KP10) has potential as a pan-tumor radiopharmaceutical for the detection of cancers. Furthermore, a lutetium-177 labelled KP10 could find therapeutic application in treating oncological diseases. We attached DOTA to the NH2-terminus of KP10 as we posited that this modification would not impair biological activity and showed that receptor stimulation of inositol phosphate accumulation in HEK293 transfected with the KISS1R gene was similar for KP10 and DOTA-KP10. We describe optimization of radiolabeling with gallium-68 and lutetium-177 and stability in serum, plasma, and whole blood. Pharmacokinetics was established with µPET/CT and ex vivo measurements. Dynamic studies with µPET/CT demonstrated that background clearance for the radiopharmaceutical was rapid with a blood half-life of 18 ± 3 minutes. DOTA-KP10 demonstrated preserved functionality at KISS1R and good blood clearance. These promising results advocate the further development of KP10 structures which have high binding affinity along with proteolytic resistance.

This paper presents the results of investigations into the pyrolysis of waste polypropylene in a laboratory fixed-bed batch reactor. The experiments were designed and verified in such a way as to allow the application of the Response Surface Methodology (RSM) in the development of an empirical mathematical model that quantifies the impacts mentioned above. The influence of the mass of the raw material (50, 100 and 150 g), together with the reactor temperature (450, 475 and 500 °C) and the reaction time (45, 50 and 75 min) was examined. It has been shown that the mass of the raw material, i.e. the filling volume of the reactor, has a significant influence on the pyrolysis oil yield. This influence exceeds the influence of reactor temperature and reaction time. This was explained by observing the temperature change inside the reactor at three different spots at the bottom, middle and top of the reactor. Recorded temperature diagrams show that with greater masses of feedstock, local overheating occurs in the middle part of the reactor, which leads to overcracking of vapor products, and from there to an increased formation of non-condensable gases, i.e. reduced yield of pyrolytic oil.

The isotopic and nuclear techniques discussed, namely: Fallout Radionuclide, Fingerprint, and Isotope Hydrology, are linked to the evaluation of soil and water degradation processes. A traditional literature review was conducted to gain the most comprehensive understanding of both the current state of the art and the subject matter, with the aim of proposing a hypothesis that integrates the synergistic convergence of these techniques in order to offer results that are more reliable. A case study is presented as a synthesis of the preceding discussion.

Depressions containing partially molten rocks were investigated in Quaternary pebbly sedi-ments in Alpine foreland in Bavaria, Germany. Ruins of limekilns from 18-19th centuries are abundant around Seeshaupt. They are usually associated with earthworks for fuel feeding and protection from wind. Depressions contain partially molten stones from furnace walls, with lime and burnt loam remnants. On the surface of pebbles (typically gneisses), green glass formed with chemical composition possibly affected by moderately volatile components of wood biomass, mainly K and Cu. Thermoplastic deformation of pebbles is limited and the sur-face melt deformation points to slow flow. At Emmerting, on the other hand, two walled circu-lar depressions which lack additional earthworks have been identified as possible impact cra-ters. Thermally affected pebbles show much more intense deformation. Colorless to greenish glass, also K and Cu enriched, usually forms only thin surface coatings, in places covered by younger melt extruded from pebble interior. Burnt loam is missing. At Grabenstätt-Kaltenbach, a depression of unclear origin was investigated. Morphologically, it matches craters rather than limekilns, but anthropogenic contamination (brick-like material) is probable. The rare molten samples do not display extreme deformation features. The thermally affected stones, mainly those from Emmerting, have elevated magnetic susceptibility.

Laser Photoacoustic Spectrometers (LPAS), which provide photoacoustic spectra for detecting food frauds or adulteration, and fluorescence-based systems for recognition of contamination by heavy metal ions in water are two important families of sensors for health and environmental purposes. Both sensor families require one or more low-frequency Lock-In Amplifiers (LIAs) to extract the signal of interest from background noise. In the cited applications, the required LIA frequency is quite low (up to 1kHz), and this leads to a simplification of the hardware with consequent good results in portability, economy, reduced size, weight and low-cost characteristics. The present system, called ENEA DSP Box Due, is based on a very inexpensive microcontroller proto-board and can replace four commercial LIAs, resulting in significant savings in both cost and space. Furthermore, it incorporates a dual-channel oscilloscope and a sinusoidal function generator. This article outlines the architecture of the ENEA DSP Box Due, its electrical characterization and its applications within a project concerning laser techniques for food and water safety.

Background/Objectives: This study aimed to identify various risk factors associated with breast cancer and explore different treatment strategies based on socio-economic, hormonal, and clinical perspectives.; Methods: We analyzed socio-economic, hormonal, genetic, and clinical variables using data from 356 questionnaires obtained from breast cancer patients at Hassan II Regional Hospital in Agadir, Morocco ; Results:The study reveals that the average age of breast cancer patients is 50 ± 10.72 years, with a mode of 47 years and an age range from 29 to 94 years. Notably, women aged 38 are most frequently diagnosed with triple-negative breast cancer. Significant socio-economic trends were observed among the participants, with the majority being housewives (91%) and nearly half residing in rural areas (48.60%). High rates of illiteracy (74.72%) and financial difficulties (54.2%) pose challenges in accessing healthcare services. Psychological distress is prevalent, with 40.7% experiencing anxiety and 30.1% experiencing sadness. The use of oral contraceptives varies, with implications for breast cancer risk. Additionally, statistics on menarche and menopause suggest hormonal influences on breast cancer development. Histological analysis indicates a predominance of grade II invasive ductal carcinoma and left breast localization. Metastases are present in nearly 38.20% of cases. Notably, surgery as the primary treatment effectively treats medium-sized tumors while limiting metastasis. Furthermore, a comparison of treatment strategies reveals a preference for letrozole among postmenopausal patients and tamoxifen among premenopausal patients; Conclusions:These findings highlight the complexity of breast cancer risk factors and therapeutic approaches, emphasizing the importance of personalized care and targeted interventions.

Despite being stored at 113 K and atmospheric pressure, LNG cold potential is not exploited to reduce green ships’ energy needs. An innovative system based on three Organic Ranking Cycles integrated into the regasification equipment is proposed to produce additional power and recover cooling energy from condensers. A first-law analysis identified ethylene and ethane as suitable working fluids for the first and the second ORC making available freshwater and ice. Propane, ammonia and propylene could be arbitrarily employed in the third ORC for air-conditioning. An environmental analysis that combines exergy efficiency, ecological indices and hazard aspects for marine environment and ship’s passengers, indicated propylene as safer and more environmentally friendly. The exergy analysis confirms more than 20% of the LNG potential can be recovered from every cycle to produce a net clean power of 76 kW, whereas 270 kW can be saved by recovering condensers' cooling power to satisfy some ship needs. Assuming the sailing mode, a limitation of 162 kg in LNG consumptions was determined, avoiding the emission of 1584 kg of CO2 per day. Marine thermal pollution is reduced by 3.5 times by recovering the working fluids' condensation heat for the LNG pre-heating.

This paper investigates the energy dissipation level of a nonlinear vehicle suspension system. The suspension system is modelled as a mass-spring-damper system, which is designed using the output frequency response function (OFRF) method. This method enables the derivation of an explicit relationship, between the system output spectrum (or Performance metric) and the system nonlinear parameters of interest. The OFRF polynomial, of the energy dissipation level, was derived in terms of the nonlinear parameters of interest. The results obtained show that the OFRF model, of the energy dissipation level, could be used to estimate the amount of heat dissipated, for a set of design parameters. This has potentials of providing some insights, in the design of vibration-based energy harvesters, as some of the wasted heat energy could be converted to electrical energy.

The genus Strophantus belongs to the Apocynaceae family of flowering plants which grows primarily in tropical Africa. The plants are widely used in traditional herbal medicine. S. sarmentosus, in particular, is used for the treatment of, e.g., joint pain and rheumatoid arthritis, wound infections, head lice, diarrhoea, snake bite, and eye conditions. Despite the widespread use, dedicated research characterizing bioactive plant components is scarce. Investigations focussed mainly on the cardenolides, because of their cardioactivity and historical use as cardiotonic. There are also studies concerning the antibacterial, antioxidant and anti-inflammatory activity of plant extracts. This review summarizes the present knowledge about the biochemical and analytical reserach on Strophantus, in general, and S. sarmentosus, in particular, and describes the current state-of-the-field based on the available sientific literature.

In this work, the surface of poly(ethylene terephthalate) track-etched membranes (PET TeMs) with pore sizes of 670-1310 nm was hydrophobized with 2,2,3,3,4,4,5,5,6,6,7,7-dodecafluoroheptyl acrylate (DFHA) by photoinitiated graft polymerization. Attenuated total reflection FTIR spec-troscopy (ATR-FTIR), scanning electron microscopy (SEM) coupled to an energy-dispersive X-ray spectrometer (EDX), and contact angle measurement were used to identify and characterize the TeMs. The optimal parameters for graft polymerization were determined as follows: polymeriza-tion time 60 min, monomer concentration of 30% and distance from the UV-source 7 cm. The wa-ter contact angle of the modified membranes reached 97° which is 51o for pristine membranes. The modified membranes were tested for water desalination using direct contact membrane distillation (DCMD) method. The effect of membrane pore size, the degree of grafting and salt concentration on the performance of membrane distillation process was investigated. According to the results obtained, it has been concluded that large pore size hydrophobic TeMs modified by using DFHA could be used for desalinating water.

Aluminium alloys are used for fabrication of fuel clad of research grade nuclear reactors as well as of several types of core components of high flux research reactors. In order to carry out design and safety analysis of these components, their mechanical and fracture properties are required by the designer. In this work, experiments have been conducted on tensile specimens machined from an aluminium alloy block to evaluate the material stress-strain curve. For evaluation of fracture properties, experiments have been conducted on disc shaped compact tension specimens in order to determine the fracture toughness of aluminium alloy. From crystal plasticity based finite element analysis and experimental data, a material damage parameter for prediction of crack initiation has been evaluated. The variation of the parameter for various values of initial a/W ratios of the disc-shaped CT specimens have been studied. It was observed that the damage parameter is independent of crack geometry and hence, it qualifies as transferable material property which can be used to predict crack initiation in a component of this material subjected to different kinds of loading conditions. In addition, the JR curves of the disc-shaped CT specimens have also been evaluated from experiments. The material damage parameter has also been used to study the crack initiation in single crystal fracture specimens with two different orientations. It was observed that the [111] orientation is more susceptible to crack initiation and propagation compared to the [100] orientation as the damage parameter is high in the ligament of the specimen ahead of the crack-tip for the same level of load. The results of the experiments and the material damage parameter shall be helpful for integrity analysis of fuel clad of research reactors as well as components of high flux research reactors.

This study investigates resource adequacy and renewable energy integration in the United States, European Union, and Pakistan amid global energy market liberalization and greenhouse gas re-duction efforts. It explores how these regions are adapting to the surge in renewable sources like wind and solar, which, despite their financial and environmental benefits, challenge resource adequacy and the economic viability of traditional energy sources. In the US and EU, significant improvements have been introduced in wholesale electricity markets and capacity accreditation mechanisms, which enhanced the large-scale deployment of renewables. This shift has prompted a reevaluation of resource adequacy, leading to increased deployment of battery storage and demand response. Presently, gas-based generation is largely upholding resource adequacy, however, future trends indicate a move towards greater consumer participation, energy efficiency, and utility-scale storage, with a decline in fossil fuel use. Pakistan aims to adopt a liberalized market structure by balancing competitive markets with legacy contracts. Public pressure is driving a shift from costly fossil-based generation to renewables. Similarly, a trend in the rise of behind-the-meter solar generation can be witnessed. In future, Pakistan may also experience resource adequacy challenges. It will likely need to implement battery storage, demand response, and modern capacity accreditation tools, by drawing lessons from developed markets.

In the last three decades the presence of phospholipids in the nucleus has been shown and thoroughly investigated. A great interest raised about nuclear inositol lipids mainly because of their role in signalling acting. Here we review the main issues of nuclear phospholipid localization and the role of nuclear inositol lipids and their related enzymes in cellular signaling both in physiological and pathological conditions.

We investigate the existence and representation of the generalized core-EP inverse of some triangular matrices over a Banach algebra. Further, the general representations of the generalized core-EP inverse of a triangular matrix over a $C^*$-algebra are presented. As applications, the generalized core-EP inverses of some block operator matrices over Hilbert spaces are given.

The microstructure evolution during the cold rolling and subsequent annealing of Alloy 800H was investigated. Two distinct rolling methods, unidirectional rolling and cross-rolling, were intro-duced. Results show that better ductility was observed in the unidirectional rolling than in cross-rolling, whilst a higher volume fraction of large deformed grains was observed in the cross-rolled plates than in the unidirectionally rolled plates. Recrystallization occurred faster in plates from unidirectional rolling than from cross-rolling.

In this work, we studied light-output properties, efficiency function as well as PSD capability of p-Terphenyl scintillator. The selected solid cylindrical scintillation detector has a size of (45 x 45) mm with PSD properties. Recently presented studies of light-output functions have been meas-ured only for low neutron energies. Our motivation has been to determine more accurate the light output function for p-Terphenyl scintillator over a wider neutron energy range. The measurements have been carried out with mono-energetic neutron beams in the wide energy range from 2.5 to 19 MeV. The neutron-gamma spectrometric system, which we developed has been used for the measurement. The input analogue signal from the detector is digitized with fast 12-bits analogue to digital converter with sampling frequency of 1 GHz. Measured data from the detector are processed into gamma and neutron spectra. The light output function for protons has been determined by finding the position of the protons for given neutron energies. The more accurate light output function for p-Therphenyl scintillator has been calculated. The pulse-shape discrimination capability as well as efficiency of p-Terphenyl scintillator in comparison with NE-213 equivalent detector is lower.

We introduce a new generalized inverse which is a natural generalization of (pseudo) right core inverse in a Banach *-algebra. We characterize this generalized inverse by using right core and quasi-nilpotent decomposition. We then present its polar-like characterization and investigate related algebraic properties. Finally, the right core-EP inverse is characterized by certain new ways.

The main goal was to investigate the ability of non-thermal plasma reactor with gliding arc discharge to remove the diesel exhaust particulates (DEPs). A conventional knifed-shaped LTP GA reactor was utilized. Three cases were studied: 140 L/min, 70 L/min and 14 L/min of air drawn through the reactor and diesel exhaust fumes were sampled continuously. They were assayed in terms of concentration and number particle size distribution. The higher the residence time’s, the higher the energy input that may be utilized for DEPs’ removal. Reactor’s performance definitely lowered the concentration of DEPs (250 - 580 nm) and altered their number size distribution. There was no effect on the number concentration, nor on the particle size distribution, of DEP particulates of 10 – 250 nm in size. The effectiveness of DEPs’ removal: Decreasing flow rate from 140 L/min to 70 L/min somehow altered the values. Achieving the airflow of 14 L/min led to a substantial improvement (even to a fourfold increase for 300 – 480 nm particles). Non-thermal plasma reactors with gliding arc discharge may be successfully adapted in the process of DEPs’ treatment. Their performance may be optimized by adjusting the airflow at the inlet of reactor to guarantee the longest aerosol residence times and the highest removal efficiency.

Multilayered metallic sheets fabricated by hot metal forming processes are attractive structural components in the aerospace and automobile industry. The strength of the mechanical bond between the different layers is critical to the applicability of such components in load bearing applications. While it is well understood that the process conditions such as temperature, deformation and rate of deformation influence the bond strength, a clear functional relationship between these conditions and the bond strength has yet to be established. The objective of the current study is to investigate the joining of Aluminum-6061 alloy specimens by hot compression bonding. Hot compression tests of beam specimen pairs were conducted at different temperatures (300-500℃), with different strains and strain rates (10-2-10-1 [1sec]). Coupled thermo-mechanical finite element models were utilized to compute the time dependent thermo-mechanical fields that develop along the specimen interface. The computed values were used to map the spatial distribution of a scalar parameter J which is hypothesized to govern bond formation. Mechanical tensile tests were used to determine the bond strength and expose the bonded surfaces. It is demonstrated that the computed J distribution can be correlated well with SEM observations of the debonded surface. It is also shown that the actual bonded area can be predicted from the computations for a certain range of critical J values.

The paper describes an application of machine learning approach for parameter optimization. The method is demonstrated for the elasto-viscoplastic model with both isotropic and kinematic hardening. It is shown that the proposed method based on long-short term memory networks enabled to obtain reasonable agreement of stress-strain curves for cyclic deformation in low-cycle fatigue regime. The main advantage of the proposed approach over traditional optimization schemes lies in the possibility to get parameters for a new material without the necessity to conduct any further optimizations. As the power and robustness of the developed method was demonstrated on the very challenging problem (cyclic deformation, crystal plasticity, self-consistent model, isotropic and kinematic hardening), it is directly applicable to other experiments and models.

The per capita availability of freshwater resources on a global scale is gradually decreasing due to population growth, rapid urbanization, industrialization, and modern lifestyles. In this situation, wastewater management becomes a major concern. Conventional treatment processes used to treat wastewater discharges are not adequate for the advanced removal of pollutants, especially refractory organic pollutants, which are mainly organic compounds that are not easily biodegradable in the environment. The use of photocatalytic membrane reactors (PMRs) for tertiary wastewater treatment has attracted much interest in recent periods, and various configurations have been investigated. The performance of a PMR using an iron doped titanium photo catalyst and Polysulfone-based polymeric membrane for municipal wastewater treatment was evaluated under natural and simulated solar light. Obtained results proved that solar driven PMRs can remove organic loading (COD) with high efficiencies and may represent a suitable alternative for the tertiary treatment step of municipal wastewater.

The nuclear reactor measurement system is a crucial component of the nuclear measurement system in a nuclear power plant. Its primary function is to measure the power distribution within the reactor core using detectors, calibrate, and provide data on core fuel consumption. Therefore, the study of the detectors' reliability is crucial for ensuring the safe operation of the nuclear power system. The article describes the operational mechanism of the gas ionization chamber detector utilized in the intermediate-range detector of the off-board nuclear measurement system. It also analyzes the movement of particles between the plates during the ionization process of the nuclear reaction taking place in the detector. The functional relationship between the current in the recombination region and the ionization region involved in the actual working condition, and the change with the increase of voltage between the plates, is deduced. A mathematical model is established for the number of pulses generated between the plates and the magnitude of the voltage between the plates. Subsequently, the change in the offset of the voltage corresponding to the inflection point of the ping curve and the change rule of the slope of the ping curve are investigated. Combined with the analysis of experimental data, the results show that the initial particle energy of Ar+, the primary sensitive particle on the detector surface, follows a normal distribution and is influenced by the energy loss associated with the initial velocity and the voltage between the plates. The trends of the inflection points and slopes of the ping curves can be utilized to evaluate the performance and operational status of the detector. Combined with the results of the experimental data analysis, the fit is good, and the inflection point currents in the normal state decrease by about 1.5% annually. The intelligent diagnostic system, based on the method studied in this paper, has been successfully implemented in the RPN digital retrofit and upgrade project at Qinshan No. 2 Plant.

When wildlife and motor vehicles collide, the result for the animals is often death (roadkill). A commercial roadkill Virtual Fence (VF) mitigation device (iPTE Traffic Solutions) was used in a field trial to test its effectiveness along a 4.9-km segment of road on Bruny Island, Tasmania. A total of 585 days of monitoring of roadkill by species was conducted, with six sections alternatively switched on or off, according to a variation of a Crossover and Multiple Before-After-Control-Impact (MBACI) experimental designs that divided monitoring into “off-on” then “on-off” blocks of periods with each “on” period followed by a 16 d “wash-out” period. For the six sections over the four periods that exclude wash-outs, the 24 aggregated values of daily counts of roadkill of Tasmanian pademelons (Thylogale billardierii), that gave a total count of 222, were modelled. Other species were killed in insufficient numbers for analysis to be informative. The statistical analysis exploited the MBACI design to estimate the VF effect using a log-odds ratio parameter (LORP) while accounting for local spatio-temporal effects. Both versions of the analysis, either averaging over the three spatial replicates (paired sections) or two temporal replicates (blocks) gave no statistically significant effect of the VF judged as a LORP estimate not sufficiently below zero. Corresponding percentage reduction estimates of 9% and 16% were derived from the LORP estimates and given parameter uncertainty estimates the power to detect as significant a LORP corresponding to a 50% reduction in rate were 0.5 and 0.6, respectively. This study confirms results from a similar field trial carried out in 2018 also in southern Tasmania and adds to the evidence that this VF is likely to give if anything only a minor reduction in roadkill for a commonly killed species for which researchers have the best chance of detecting any practically useful reduction.

In this paper, the neural network is developed for solving the inverse photoacoustic problem aiming to estimate thermo-elastic properties and thickness of a semiconductor sample. The idea was that these sample properties be estimated from the phase characteristic because the phase measurements are more sensitive. The neural network has been trained on a large basis of photoacoustic phases calculated from a theoretical Si n-type model in the range of 20Hz to 20kHz, on which random Gaussian noise has been applied. It is shown that high accuracy and precision could be reached in solving of inverse photoacoustic problem using only phase measurement.

To support the integration of renewable energy sources and preserve grid stability, this study examines several approaches for controlling the temperature of Battery Energy Storage Systems (BESS) in modern energy settings. Specifically, the usage of BESS in Virtual Power Plants (VPPs) is the focus of this study. The effectiveness, safety features, dependability, affordability, and suitability for VPP applications of these systems are examined. Among the various hybrid cooling alternatives, two particularly promising combinations emerge. Firstly, the integration of heat pipes and phase change materials leverages their ability to conduct heat efficiently away from heat sources with minimal temperature differences, making them excellent for rapid heat transfer. Secondly, an approach employing heat pipes and liquid passive cooling a combination that capitalizes on the efficient heat transfer capabilities of heat pipes and the consistent cooling offered by liquid passive systems. The study underscores the importance of improving BESS performance and sustainability within VPPs by providing useful recommendations for choosing the best thermal management system depending on climate conditions and geographic location.

In this work SiC-Ti3AlC2 and TiC-Ti3AlC2 composites produced by additive manufacturing are investigated. The fused granules fabrication (FGF) method as one of the material extrusion additive manufacturing (MEAM) technology is used to obtain composite samples. Composites with different ratios between components and different powder:polymer ratios are investigated. The technological features of the additive formation of composites are investigated, as well as their structure and properties. The optimal sintering temperature to form the best mechanical properties for both composites is 1300 °C. The composites have a regulatable porosity. Ti3AlC2 content, sintering temperature, and polymer content in the feedstock are the main parameters that regulates the porosity of FGF samples.

The objective of this paper was to verify the applicability of statistical learning (SL) compared to human reasoning with respect to the Universal Thermal Climate Index (UTCI), a complex tool for the assessment of outdoor thermal stress. UTCI is an equivalent temperature index based on the 48-dimensional output of an advanced model of human thermoregulation formed by 12 variables at four consecutive 30-minute intervals, which were calculated for 105642 thermal conditions from extreme cold to extreme heat. Comparing the performance of SL algorithms to the results accomplished by an international endeavor involving more than 40 experts from 23 countries, we found that random forests and k-nearest neighbors closely predicted UTCI values, but that clustering applied after dimension reduction algorithms (principal component analysis and t-distributed stochastic neighbor embedding) were inadequate for risk assessment in relation to the UTCI stress categories. This indicates a potential supportive role for SL, as it will not (yet) fully replace the bio-meteorological expert knowledge.

Taking into account modern technologies in the mining industry and in the processing of industrial waste, we propose to reprocess cemented low- and intermediate level radioactive waste by extracting all chemical compounds from them. Because of the low cost of space flights in the near future, we propose to use chemical compounds, extracted from radioactive waste, in the production of space electronics and structural materials for automatic space probes and rovers. At the same time, since nano- and micro powders, as well as composites with these fillers, are widely used today in electronics and technology, including in the space industry, the production of radioactive powders and composites will provide new scientific results in the field of materials science and solid-state physics, since nothing is known today about the properties of radioactive powders and composites containing radioactive sources inside.

This paper presents the results of investigations on the kinetic of Brilliant Blue FCF (BB) discoloration reactions in aqueous solutions with different ozone concentrations and pH conditions. Kinetic studies involve knowledge of the structure and properties of the dye and ozone, as well as the experimental conditions. In general, scientists admit that the predominant oxidation pathway is direct (by free oxygen atoms) or indirect (by free hydroxyl radicals), it will depend on influencing factors such as: the physicochemical properties of the dye, the pH of the aqueous solution, ozone concentration, reaction time and the contact mode with/without stirring. In the experimental research, two pathways were chosen following CBB = f(t): 1. constant dye concentration and different ozone concentration on the concentration range (100 - 250 mg/L) at three pH media (acidic, neutral and basic) with and without stirring; 2. Constant concentration of ozone and different dye in the range of concentrations (2.5 - 10 mg/L) under the conditions of point 1. With obtained experimental data the curves CBB = f(t) were drawn and were processed by the integral method of classical kinetic based on first and second order equations. Unfortunately, this simple procedure this not yield any minim full results and any pH level. The rate constants been negative and/or the reaction order been dependent on initial conditions. Due to its structure, the BB dye has several chromophore groups, thus multiple attack centers, resulting in more oxidation by-products, which is why the 1H - NMR spectrum of BB discoloration with ozone was recorded.

Investigation of functional magnetic resonance imaging (fMRI) data with machine learning (ML) techniques, including also deep learning (DL) methods, have been widely used to study Autism Spectrum Disorder (ASD). This disorder is characterized by symptoms that affect the individual’s behavioral aspects and social relationships. Early diagnosis is crucial for intervention, but the complexity of ASD poses challenges for treatment development. This study compares traditional ML techniques with deep learning (DL) methods in the analysis of functional connectivity measures obtained from the time series of multicentric ABIDE dataset. Specifically, Support Vector Machines (SVM) classifiers, with both linear and Radial Basis Function (RBF) kernels, as well as eXtreme Gradient Boosting (XGBoost) classifiers, are compared against the TabNet classifier, which is a DL architecture customized for tabular data analysis and a Multi Layer Perceptron (MLP). The findings suggest that DL classifiers may not be optimal for the type of data analyzed, as their performance trails behind that of standard classifiers. SVMs achieve performances, in terms of AUC, around 75%, compared to the best TabNet and MLP results, which are 65% and 71%, respectively. Additionally, this work investigates the brain regions that contribute most to the classification task, which are found to be those primarily responsible for sensory and spatial perception, as well as attention modulation, known to be altered in ASD.

The importance of personalized medicine is growing, since there is an urged need to avoid unnecessary and expensive treatments. In nuclear medicine, the theranostic approach is an established tool for a specific molecular targeting in means of diagnostics and therapy. The visualisation of potential targets can help to predict if a patient would benefit from a particular treatment or not. Thanks to the quick development of radiopharmaceuticals and diagnostic techniques, the use of theranostic agents is constantly rising. In this article important milestones of nuclear therapies and diagnostics in the context of theranostics are highlighted. It begins with the well-known radioiodine therapy in patients with thyroid cancer and then guides through different approaches for the treatment of advanced cancer with targeted therapies. The aim of this review is to provide a summary of background knowledge, current applications and advantages of targeted therapies and imaging in nuclear medicine practice.

The Atmospheric Dynamics Mission ADM-Aeolus was successfully launched in August 2018 by the European Space Agency (ESA). The Aeolus mission carried a single instrument, the first-ever Doppler Wind Lidar (DWL) in space, called Atmospheric LAser Doppler INstrument (ALADIN). Aeolus circled the Earth in a polar sun-synchronous orbit at about 320 km altitude with a repeat cycle of 7 days, providing vertical profiles of horizontal line-of-sight (HLOS) winds on a global scale. Exceeding scientific expectations, Aeolus, initially designed for a 3-year lifetime, provided global coverage of wind profiles for almost five years. In this long-term validation study, we assessed the accuracy of the Level 2B (L2B) Rayleigh-clear and Mie-cloudy wind products by collecting radiosonde data from three stations in the Brazilian Amazon: Cruzeiro do Sul (7.62° S, 72.67° W), Porto Velho (8.76° S, 63.91° W), and Rio Branco (10.00° S, 67.80° W). Statistical validation was conducted by comparing Aeolus L2B wind products and radiosonde data, launched daily at 12:00 UTC from October 2018 to March 2023. Considering all data collected during the mission period, Pearson’s coefficient (R) of 0.73 was observed in Rayleigh-clear and 0.85 in Mie-cloudy, revealing a strong correlation between Aeolus and radiosonde winds. No significant biases were detected, with values of -0.14 m/s for Rayleigh-clear and -0.40 m/s for Mie-cloud, fulfilling the mission requirement of having absolute biases below 0.7 m/s. However, when analyzed annually, in 2022, the bias for Rayleigh-clear was -0.95 m/s, exceeding the mission requirements.

Bulk composition, mineralogy and microchemistry of various fractions of the filling of the Crater No. 4 at Emmerting were investigated. Here we present mainly the fine fractions, which, in contrast to pebbles larger than ca. 4 cm, are relatively poor in material affected by melting. A 0.1 mm long meteorite fragment without ablation features was found, and remelted fragments of the same body have been identified. The projectile was dominated by enstatite, also containing forsterite, basic plagioclase, Ni-rich pyrrhotite and troilite, kamacite, silica, and probably merrillite. The molten fragments contain porous Mg-rich glass (indicating temperature &gt; 1500 °C), minor Fe oxides, and occasionally uncommon Ni-rich minerals. The bulk composition and electron microprobe show that the amount of meteoritic material is low (&lt;&lt; 1 %), and it is not unequivocally manifested even in platinum-group elements abundances and osmium isotope ratios (the latter, however, were only measured in two samples). This can be explained by dilution of the filling by particles brought after the crater formation, and by probably achondritic composition of the projectile. Relatively large hollow spheroid Fe oxide particles were observed in thin sections from the magnetic fraction. A Mn oxide hollow spherule has also been found. In magnetically separated filling from the nearby Crater No. 5, bulk chemical composition points to contamination with several metals and metalloids probably due to influence of recent alluvial sediments. Therefore, the extent of meteoritic contamination in this crater may be even smaller.

Studies and opinion articles present unequal conclusions concerning empathy and morality, mainly because a somewhat heterogeneous and foggy conceptual approach prevails. This scoping review aims to analyse the relationship between empathy and morality and to present a novel conceptual model of empathy applied to moral decisions.A search in PsycINFO, Scopus and PubMed identified articles addressing the relationship between empathy and morality.Thirty-two articles were included. We find an absence of a consensual definition of empathy. It is commonly defined as a predominant emotional process and a factor of bias and prejudice in moral decisions.According to our conceptual model, empathy is a distinct, complex human neuropsychological capacity that mobilises and is dependent on the proper functioning of several brain areas and balances the scales on which are Emotion and Reason, enabling the most thoughtful moral decisions possible in diverse circumstances and contexts.

The Shimensi super-large tungsten polymetallic deposit is located in Late Jurassic- Early Cretaceous Porphyry-Skarn tungsten ore belt in the south Yangtze metallogenic belt. There are 3 types of mineralization: veinlet-disseminated type, thick quartze vein type and hydrothermal crypto-explosive breccia type. Based on geological studies, this paper presents new petrographic, microthermometric, laser Raman spectroscopic and hydrogen and oxygen isotope research of the fluid inclusions from the deposit. The results show that there are five different types of fluid inclusions: liquid-rich inclusions, vapor-rich inclusions, pure liquid inclusions, pure vapor inclusions, and fluid inclusions containing a solid crystal. The homogenization temperatures of the fluid inclusion range from 140℃-270℃, the salinities are 3%-5% NaCleq and the densities of ore-forming fluid range from 0.64 g/cm3 to 0.99 g/cm3. For the analyses of Laser Raman spectroscopic, the ore-forming fluids can be approximated by a Ca2+-Na+-SO42--Cl- fluid system with small amount of CO2, CH4 and N2. Otherwise, the datas of the pressure, pH and Eh show a fluid metallogenic environment of low pressure, weak acid and weak reduction. The values of the homogenization temperature in 3 types of orebodies suggest that the mineralization is characterized by the decrease of the temperature under the condition of the fluid immiscibility. The H-O isotope values are interpreted to indicate that the ore-forming fluids are mainly composed of magmatic water, and also the meteoric water was added with the process of the magma rising.

Wide bandgap semiconductors-based photocatalysts are usually limited by their low solar energy conversion efficiency due to their limited absorption solar wavelength, surface’s fast recombination of photoelectron–hole pairs and low charge-carrier mobility. Here we report a new stepwise solution synthesis for making a new photocatalytic core/shell of titanate nanowire/reduced graphene oxide shell (or titanate/rGO) 1D-nanocomposite. The new core/shell nanocomposite maximized the specific surface area, largely reduced the charge transfer resistance and reaction energy barrier, and significantly improved the absorption of the visible light. The core/shell nanocomposites’ large on/off current ratio and rapid photo-responses boosted the photocurrent by 30.0%, the photocatalysis rate by 50.0%, and the specific surface area by 16.4%, when comparing with the pure titanate nanowire core. Our numerical simulations support the effective charge separation on the new core-shell nanostructure, which can help further advance the new photocatalysis.

The superfamily of Acid proteases has two catalytic aspartates for proteolysis of their peptide substrates. Here, we show a minimal structural scaffold, the Structural Catalytic Core (SCC), which packs all conserved substructure elements around the catalytic machinery, and which can be found in all enzymes of the Acid proteases superfamily. The SCC is a dimer of several structural blocks, such as the DD-link, the D-loop and the G-loop, around two catalytic aspartates in each protease subunit or within an individual chain. The dimer of two D-loop/DD-link substructures makes a DD-zone, and the dimer of two D-loop/G-loop substructures makes a psi-loop. These structural markers are useful for protein comparison, structure identification, protein family separation and protein engineering.

In this paper, we study the effect of decreasing aperture diameter on signal transmission from the scintillator to the PMT. The apertures have been inserted directly between the scintillator and the photomultiplier. Three different aperture diameters have been used over a wide energy range.A newly developed fast digital spectrometer has been utilised for experimental measurement in the radial channel of the VR-1 research reactor. The detector signals with and without inserted apertures have been measured and evaluated. The aim of our research was to determine the effect of the apertures on the spectral quality, energy range and the evaluated physical quantities.

Pyrethroid pesticides (PYRs) as the third most widely used pesticides, following organophosphorus and carbamate pesticides, which are of significant importance in the analysis and detection of vegetables. However, the current pretreatment technology for PYRs confronts challenges of difficult separation and low enrichment efficiency, resulting in a cumbersome and time-consuming pretreatment process with poor selectivity. Here, a simple and efficient magnetic solid-phase extraction (MSPE) strategy was developed to simultaneously purify and enrich five PYRs in vegetables, with the magnetic covalent organic framework nanomaterial COF-SiO2@Fe3O4 as an adsorbent. The COF-SiO2@Fe3O4 was prepared by a simple solvothermal conditions method, using Fe3O4 as magnetic core, benzidine and 3,3,5,5-tetraaldehyde biphenyl as two building units. COF-SiO2@Fe3O4 could effectively capture the targeted PYRs by virtue of its abundant π-electron system and hydroxyl groups. The impact of various experimental parameters on extraction efficiency was investigated to optimize the MSPE conditions, including adsorbent amount, extraction time, elution solvent type and elution time. Subsequently, method validation was conducted under the optimal conditions in conjunction with gas chromatography-mass spectrometry (GC-MS). Within the range of 5.00–100 μg·kg-1 (1.00–100 μg·kg-1 for bifenthrin and 2.5–100 μg·kg-1 for fenpropathrin), the five PYRs exhibited a strong linear relationship, with determination coefficients ranging from 0.9990 to 0.9997. The limits of detection (LODs) were 0.3–1.5 μg·kg-1, and the limits of quantification (LOQs) were 0.9–4.5 μg·kg-1. The recoveries were 80.2–116.7% with relative standard deviations (RSDs) below 7.0%. Finally, COF-SiO2@Fe3O4, NH2-SiO2@Fe3O4 and Fe3O4 were compared as MSPE adsorbents for PYRs. The results indicated that COF-SiO2@Fe3O4 was an efficient and rapid selective adsorbent for PYRs. This method holds promising prospects for the determination of PYRs in real samples.

In this paper, the time-resolved model of photoacoustic signal for samples with a complex inner structure is derived including local non-equilibrium of structural elements with multiple degrees of freedom, i.e. structural entropy of the system. The local non-equilibrium is taken into account through the fractional operator. By analyzing the model for two types of time-dependent excitation, a very short pulse and a very long pulse, it is shown that the rates of non-equilibrium relaxations in complex samples can be measured by applying the derived model and time-domain measurements. Limitations of the model and further directions of its development are discussed.

Compared to agonists, radiolabeled somatostatin receptor (SSTR) antagonists have advantages in neuroendocrine tumors (NETs). Articles on radiolabeled somatostatin receptor agonists or antagonists in NETs were included by searching the Web of Science (WoS) database. The included literature has been subjected to data collection and bibliometric study. A detailed analysis of the included clinical articles was also performed. 123 publications were identified for biblio-metric analysis. The number of publications on radiolabeled somatostatin receptor agonists and antagonists in the theranostics of NETs has increased significantly after 2014, with Germany publishing the most papers (39), followed by the United States (33) and Switzerland (28). The Swiss paper was cited the most, with 1783 quotations, followed by the USA (1338) and Germany (1330). The most common keywords were NETs (89), Peptide receptor-mediated radionuclide therapy (PRRT) (62), and antagonists (53). Antagonists had lower uptake in normal tissue and higher uptake in tumor tissue compared to agonists, with a high tumor-to-liver ratio. Research on radiolabeled somatostatin receptor agonists and antagonists in theranostics of NETs is increasing, with significant contributions from Europe and the United States. Radiolabeled somatostatin receptor antagonists are likely to be a hot topic in NETs theranostics.

This study introduces numerical advancements in an alternative design for the SPS Beam Dump Facility (BDF) at CERN. The design envisions a high-power operation target made of flowing liquid lead. The BDF is a proposed versatile facility at CERN, intended for both beam-dump-like and fixed-target experiments. The target behavior is assessed, assuming a proton beam with a momentum of 400 GeV/c, a pulse frequency of 1/7.2 Hz, and an average beam power of 355 kW. An evaluation is conducted using various Computational Fluid Dynamics (CFD) codes to analyze the behavior of liquid lead and to predict the thermal stress on the target vessel induced by the pulsed heat source generated by the charged particle beam. The comparison increases the reliability of the results, investigating the dependencies on the CFD modeling approach. The beam is modeled as a volumetric heat source with data coming from beam-lead interaction simulations provided by CERN and obtained with the Monte-Carlo code FLUKA. The velocity field and stress profiles are utilized to enhance the design of the lead loop and verify its viability and safety when operated with a liquid metal target.

The expansion of renewable energies is progressing strongly. The influence on the power supply networks by the volatility of the infeed must be met with new concepts. In this paper we investigate the possibilities of integrating microgrids as a cooperating unit in the power supply network to support further expansion of RES power plants. In this paper a differentiation of microgrids from similar network structures is established, a classification of proposed groups is made. Then, after the description of simulation of components in a microgrid, with practical advice, an example model is shown, which aids the dimensioning of the components within a microgrid to achieve a specified goal.

The calculation and visualization of the dose field in the decommissioning of nuclear facilities is one of the important functions of the decommissioning virtual simulation system, which can provide accurate and intuitive radiation field distribution and play an important role in determining the demolition plan and protecting personnel during the engineering implementation process. This article investigates the development of dose field calculation and visualization in the reactor decommissioning virtual simulation systems, and preliminarily proposes a technical plan suitable for the development of the decommissioning dose field calculation and visualization display programs for the first Heavy Water Research Reactor (HWRR) in China. Besides, the applicability of the selected scheme is analyzed, the functional requirement and development direction of the HWRR reactor decommissioning dose field calculation and visual display module are preliminarily determined. Furthermore, the reactor vessel of HWRR reactor is modeled and the dose field distribution was calculated and visualized. This research can provide technical support for the development of the decommissioning simulation system for the first HWRR reactor in China.

A tritium resistant coating on the surface of materials is one of the main methods to reduce tritium permeability. In actual operating processes, mechanical damage such as spalling and scratches will occur on the surface of tritium resistant coatings. These mechanical damages will affect the hydrogen permeability resistance of the coatings. It is an important engineering problem that evaluate the effect of these damage on the tritium resistance of the coating. In this experiment, the mechanical damage of FeAl/Al2O3 tritium resistant coating on 316L stainless steel was simulated by scratching, debonding and thermal shock, and the gas hydrogen isotope permeation (GDP) test was carried out. The influence of mechanical damage degree on the tritium permeation behaviour of the coating was evaluated and discussed.

Background/Objectives: Although the role of F-18 FDG PET/CT imaging is well established in oncology, its diagnostic value in routine monitoring for recurrent colorectal cancer (CRC) is still controversial. The aim was to evaluate the diagnostic value of FDG PET/CT in detecting recurrent CRC in correlation with CEA, CA 19-9 levels, and conventional imaging modalities (CIM). Methods: Between 2009 and 2023, we retrospectively studied 134 CRC patients referred for FDG PET/CT imaging on the suspicion of recurrence based on elevated CEA and/or CA 19-9, and/or equivocal radiological findings. According to the Institutional Tumor Board CRC protocol, after initial treatment which was dependent on TNM stage (neoadjuvant therapy, primary resection or adjuvant treatment), patients underwent a standard 5-year surveillance including CEA and CA 19-9 measurements, CIM, and colonoscopy every 6 months. The statistics including univariate and multivariable analyses were conducted using the IBM SPSS 20.0 statistical software. P-values <0.05 were considered statistically significant. Results: Recurrent CRC was confirmed in 54/134 (40.3%) patients with elevated tumor markers. FDG PET/CT shows high diagnostic performance in detecting recurrent CRC with sensitivity, specificity, PPV, NPV, and accuracy of 94.4%, 82.5%, 78.5%, 95.7%, and 87.3%, respectively. The CEA shows a high sensitivity of 98.1%, but both low specificity and accuracy of 15% and 48.5%, respectively. The sensitivity, specificity, and accuracy, for CA 19-9 and CIM for the correct diagnosis in CRC patients were: 44.4%, 67.5%, 58.2%, and 51.9%, 98.8%, 79.9%, respectively. The AUC for FDG PET/CT, elevated CEA levels, CIM, and elevated CA 19-9 levels was 0.885 (95% CI: 0.824-0.946; p<0.001), 0.844 (95% CI: 0.772-0.916; p<0.001), 0.753 (95% CI: 0.612-0.844; p<0.001); and 0.547 (95% CI: 0.442-0.652; p=0.358). Univariate analysis shows that both FDG PET/CT- and CIM-positive results were highly associated with CRC recurrence (p<0.001 and p<0.001, respectively), while gender, mucinous tumor type, presence of initial lymph node metastasis (N+), and presence of initial distant metastasis (M+) have no significance (p=0.211, p=0.158, p=0.583, and p=0.201, respectively). Our multivariate analysis shows that independent predictors for CRC recurrence are: positive FDG PET/CT scans (p<0.001), positive CIM results (p=0.001) and elevated CA19-9 levels (p=0.023). Although CA 19-9 was not detected as a statistically significant predictor in the univariate analysis (p=0.358), in a multivariate analysis it was recognized as a significant predicting factor in detecting CRC recurrence (p=0.023). Conclusions: FDG PET/CT shows a high diagnostic efficacy in CRC recurrence detection, in correlation with CEA levels, CA 19-9 levels, and CIM. This imaging modality should be routinely integrated into the postoperative follow-op in patients with elevated tumor markers.

Abstract: Imaging of low (LGG) to high (HGG) grade gliomas is conventionally performed with MRI, which is the non-invasive gold-standard imaging modality to derive data. Gliomas (Grade 1,2,3,4) are lethal and demonstate poor outcomes despite novel therapies. Integrins compose of heterodimeric parasympathetic nervous system; the aVb3 (RGD i.e. Galacto-Arginine-Glycine-Aspartic acid) have been displayed as a potential biomarker that can be imaged via PET in order to trace the angiogenetic pathway. Gliomas are common primary central nervous system (CNS) tumours which are often pose a diagnostic challenge, even to stage and manage because of their heterogeneity in molecular aberrations. Several core mutational core hallmarks of gliomas are inducing/accessing vasculature, tumour promoting inflamation, polymorphic microbes and avoiding/resisting cell death; these ultimately lead to poor prognosis. In 2007, the classification of diffuse gliomas was based on the histopathology and subtype e.g. Pilocytic astrocytoma and low cell proliferation, in 2016, the classification of diffuse gliomas was based on the IDH status, 1p/19q codeletion, subtype and grade; then in 2021, the IDH status (wild-type or mutant), molecular profile, subtype and grade were added in order to improve the classification of diffuse gliomas. Imaging (MRI) techniques progress stalled despite the imperfections in MRI e.g distinguishing RN (radionecrosis) and PsP (Pseudoprogression) hence the exploration of PET probes that detect important hallmarks of gliomas e.g. techniques such as [68Ga]68Ga-RGD positron emission tomography (PET) to be utilised to assess vasculature. This case report aimed to determine the potential clinical utility of molecular imaging with 68Ga-RGD PET used in complementary to traditional MRI techniques.

We have repeated the experiment performed recently by Krasznahorkay et al., (Phys. Rev. Lett. 116, 042501 (2016)), which may indicate a new particle called X17 in the literature. In order to get a reliable, and independent result, we used a different type of electron-positron pair spectrometer which have a more simple acceptance/efficiency as a function of the correlation angle, but the other conditions of the experiment were very similar to the published ones. We could confirm the presence of the anomaly measured at the Ex=18.15 MeV resonance, and also confirm their absence at the Ex=17.6 MeV resonance, and at Ep= 800 keV off resonance energies.

Cancer theragnostics is a novel approach that combines diagnostic imaging and radionuclide therapy. It is based on the use of a pair of radiopharmaceuticals, one optimized for positron emission tomography imaging, through linkage to a proper radionuclide, and the other bearing a beta-emitter isotope that can induce significant damage to cancer cells. In recent years, the use of theragnostics in nuclear medicine clinical practice has increased considerably, and thus investigation has focused on the identification of novel radionuclides that can bind to molecular targets which are typically dysregulated in different cancers. The major advantages of the theragnostic approach include elimination of multi-step procedures, reduced adverse effects to normal tissues, early diagnosis, better predicting responses and personalized patient care. This review aims to discuss emerging theragnostic molecules that have been investigated in a series of human malignancies, including gliomas, thyroid cancer, neuroendocrine tumors, cholangiocarcinoma and prostate cancer, as well as potent and recently introduced molecular targets, like cell-surface receptors, kinases, and cell adhesion proteins. Furthermore, special reference has been made to copper radionuclides as theragnostic agents, and their radiopharmaceutical applications since they present promising alternatives to the well-studied gallium-68 and lutetium-177.

Many of the fundamental molecules of life share extraordinary pigment-like optical properties in the long-wavelength UV-C spectral region. These include strong photon absorption and rapid (sub pico-second) dissipation of the induced electronic excitation energy into heat through peaked conical intersections. These properties have been attributed to a ``natural selection'' of molecules resistant to the dangerous UV-C light incident on Earth's surface during the Archean. In contrast, the ``thermodynamic dissipation theory for the origin of life'' argues that, far from being detrimental, UV-C light was, in fact, the thermodynamic potential driving the dissipative structuring of life at its origin. The optical properties were thus the thermodynamic ``design goals'' of microscopic dissipative structuring of organic UV-C pigments, today known as the ``fundamental molecules of life'', from common precursors under this light. This ``UV-C Pigment World'' evolved towards greater solar photon dissipation through more complex dissipative structuring pathways, eventually producing visible pigments to dissipate less energetic, but higher intensity, visible photons, up to wavelengths of the ``red-edge''. The propagation and dispersal of organic pigments, catalyzed by animals, and their coupling with abiotic dissipative processes, such as the water cycle, culminated in the apex photon dissipative structure, today's biosphere.

Soft magnetic composites cores were produced by Spark Plasma Sintering (SPS) from Ni3Fe@ZnFe2O4 and NiFeMo@ZnFe2O4 pseudo-core-shell powders. In the Fe-Ni alloys@ZnFe2O4 pseudo-core-shell composite powders, the core is a large nanocrystalline Permalloy or Supermalloy particle obtained by mechanical alloying, and the shell is a pseudo continuously layer of Zn ferrite particles. The pseudo-core-shell powders have been compacted by SPS at temperatures between 500-700 ºC, with a holding time of 0 minutes. Several techniques were used for the characterisation of the powders and sintered compacts: X-ray diffraction, scanning electron microscopy, energy dispersive X-ray spectroscopy, magnetic hysteresis measurements (DC and AC) and electrical resistivity. The electrical resistivity is stabilised at values of about 7·10-3 Ω·m for sintering temperatures between 600-700 °C and this value is 3 orders of magnitude higher than the electrical resistivity of sintered Fe compacts. The best relative initial permeability was obtained for the Supermalloy/ZnFe2O4 composite compacts sintered at 600 ºC, which decreases linearly for the entire frequency range studied, from around 95 to 50. Up a frequency of 2,000 Hz the power losses are lower than 1.5 W/kg. At the frequency of 10 kHz, the power losses are larger, but they remain at a low level. In the case of Supermalloy/ZnFe2O4 composite compact SPS-ed at 700 °C, the specific power losses are even lower than 5 W/kg. The power losses decomposition proved that intra-particles losses give the main part of the losses.

In the present work consideration is given to the primordial black holes ({\bf pbhs}) in the Schwarzschild-de Sitter Metric with small mass (ultralight) in the preinflationary epoch. Within the scope of natural assumptions, it has been shown that the quantum-gravitational corrections ({\bf qgcs}) to the characteristics of such black holes can contribute to all the cosmological parameters, shifting them compared with the semiclassical consideration. These contributions are determined by a series expansion in terms of a small parameter dependent on the hole mass (radius). For this pattern different cases have been considered (stationary, black hole evaporation...). It has been demonstrated that involvement of ({\bf qgcs}) leads to a higher probability for the occurrence of such {\bf pbhs}. Besides, high-energy deformations of Friedmann Equations created on the basis of these corrections have been derived for different patterns. In the last section of this work it is introduced a study into the contributions generated by the above-mentioned {\bf qgcs} in inflationary cosmological perturbations. Besides, it has been shown that non-Gaussianity of these perturbations is higher as compared to the semi-classical pattern.

Nuclear waste is one of the most important environmental problems of nuclear power plants. A novel renewable distillation method has been proposed for an on-site recycling of the spent nuclear fuel and separation of its valuable components from the fissile isotopes, which is especially applicable for reactors using liquid fuels.

The German health authorities' guidelines for medical devices in 2012 highlighted the importance of cleaning ultrasound probes, emphasizing their validation and reliability. In addition to automated and validated options, alternative manual methods such as wipe disinfection have gained traction due to their independence from additional hardware. The study examines the effectiveness of manual disinfection methods, specifically the cleaning process, addressing concerns raised by the Robert Koch Institute regarding the lack of validation for wipe disinfection of semi-critical devices. The EQUINOS colored wipe disinfection kit identified wetting gaps in all cleanings across four probes tested. The results indicate significant challenges in ensuring complete surface wetting, particularly in complex body parts such as clip-on areas and shapes for additional biopsy attachments, suggesting that manual methods alone may not adequately mitigate the risk of infection transmission (p value .001). The study concludes that while manual disinfection methods are a viable alternative to automated reprocessing, there is a critical need for enhanced training and potentially the development of more effective manual disinfection techniques or colored wipes to ensure patient safety and compliance with healthcare hygiene standards.

Overconsumption of an unbalanced diet and overweight, leading to insulin resistance, dyslipidemia, hepatic steatosis, cardiovascular diseases and obesity, is nowadays a worldwide health issue, with different patterns of metabolic disturbances in the young and adult popula-tions, in both gender. Preclinical models that closely mimic the gradual weight gain that occurs in humans upon consumption of a “western-type” diet (WD) are of great interest. In particular, the diet-induced obesity (DIO) model in the C57BL/6J mouse sub-strain is often used in biomed-ical research, considering that it is prone to metabolic disorders and obesity, and is widely used to generate genetically modified mice. This study aimed to phenotypically characterize the C57BL/6J mouse strain fed a WD-like diet, using high-frequency ultrasound imaging (HFUS) as a complementary tool to longitudinally monitor morphofunctional changes in the liver, heart and kidney associated with DIO. Long term WD feeding increased mice body weight (BW), liver/BW ratio and body condition score (BCS), serum transaminases, glucose and insulin, as well as Homeostasis model assessment (HOMA) indexes, and caused dyslipidemia and insulin resistance. According to the 3Rs, ultrasound imaging has enabled a comprehensive study of metabolic syndrome in mice, in vivo and non-invasive, improving the identification of early stages of diseases.

A study of cryogenic drilling in sandwich composites has been carried out. Materials used have been carbon fiber reinforced polymer sandwich sheets with inner foamed polyvinyl chloride core, composites with aerospace, marine, construction and automotive applications, including protec-tion structure of Polar engineering equipment. Experimental tests have been performed in lam-inates with 12 mm and 6 mm of thickness, drilling with liquid nitrogen as refrigerant to reach temperatures below -120ºC under different cutting conditions, in particular, drill rotation speeds between 2000 rpm and 6000 rpm and feed rates between 200 mm/min and 600 mm/min. Variables as thrust forces and circularity error have been measured, due to the importance of its effect on the hole quality, as an operation prior to a possible assembly. A design of experiments has been allowed determining relationships between variables, identifying the influence of cutting condi-tions on the thrust force and the circularity at inlet and outlet holes.

Public restrooms are often a hub of microbial contamination, and the examination of bacterial contamination in these facilities can serve as an important indicator of the transmission of infectious diseases. This study was conducted to determine the prevalence of bacterial contamination in public restrooms based on the economic class of the building. Samples were collected from various spots in 32 restrooms found in 10 shopping malls, classifying them into two categories: upper-end restrooms and lower-end restrooms. The findings showed that the level of contamination was higher in the lower-end restrooms, with the seat being the most contaminated area. The most dominant Gram-positive bacteria were coagulase-negative staphylococci species, making up 86% of the identified Gram-positive isolates. The most dominant Gram-negative bacteria identified were Klebsiella pneumoniae and Pseudomonas aeruginosa. The antibiotic sensitivity test results revealed the presence of multi-drug resistant bacteria among the Gram-positive and negative isolates, including Staphylococcus haemolyticus, Staphylococcus kloosi, Acinetobacter baumanii, and Pseudomonas aeruginosa. In conclusion, the study underscores the significance of monitoring bacterial contamination in public restrooms and the need for measures to reduce the spread of infectious diseases. Further research is crucial to gain a complete understanding of the bacterial contamination in public restrooms and their resistance patterns, to ensure the safety and health of the public. The implementation of improved cleaning practices and hands-free designs in restrooms can help reduce the risk of cross-contamination and prevent the spread of diseases.

The strong competition in the automotive industry has required manufacturers to implement lean production, both with methods and techniques specific to Industry 4.0. At the same time, universities must provide graduates with specific skills for applying these new production methods and techniques. In this context, a Lean Learning Factory was developed in the Pitesti University Center, which allows students to learn, experiment, and research, in an environment similar to that of enterprises, the new Lean Manufacturing methods and techniques, and Industry 4.0. The research presented in this study had as its objective identifying the minimum number of repetitions necessary to train operators who serve two differently organized workstations, one classic, the other including digital techniques, but on which the same assembly operation is performed. Several indicators were considered in the analysis, such as the number of errors, the number of stops, the effective duration of the work cycle, and the percentage ratio between the standard duration of cyclical activities and the effective duration of the work cycle. The evolution of these indicators was mathematically modelled by regression functions, using the least squares method. The obtained results also highlight the usefulness of applying the DOJO method as a Lean manufacturing-specific learning technique and the efficiency of implementing digital techniques in work organization.

Energy consumption modelling is of critical importance for improving energy efficiency in the drive towards sustainable manufacturing. Modern manufacturing processes and machine tools are very complex as they involve interplay of several advanced technologies. Therefore, energy modelling of modern machine tools is a complex multi-disciplinary task. This paper proposes a systematic and practical framework to choose the appropriate modelling approach for a given industrial problem. The framework was validated by applying it to diverse industrial scenarios.

The true ternary fission, the fission of a nucleus into three fragments of nearly equal mass, is an elusive and poorly known process influenced by shell effects. It has been envisaged an increase of the probability of this process with respect to the binary fission, very low in spontaneous and neutron-induced fission, by adopting heavy-ion induced reactions due to the possibility to increase the fissility parameter and the excitation energy of the compound nuclei. Nuclei with mass number around A=250, accessible in heavy-ion induced reactions, are favorable and should be investigated. It is still debated if the process takes place in a single step, direct ternary fission, or in two steps, sequential ternary fission. The purpose of this work is to define experimental conditions and observables that allow the disentangling of the products from the direct and sequential ternary fission as well as from the usual most probable binary fission. This step is essential to gain insight on the ternary fission dynamics and on the binary to ternary fission competition. The method proposed here is to simulate the kinematics of the ternary and binary fission processes to compute the energy distributions and angular correlations of direct and sequential ternary fission products, as well as those of binary fission. The reaction taken as benchmark is 40Ar+208Pb at 230 MeV supposed to form the 248Fm* compound nucleus. The simulation results have been filtered by considering the response function of a multi-coincidence detection system virtually constructed using the Geant4 simulation toolkit. The simulations support the possibility to separate the products of different multimodal fission decays with the proposed setup that consequently represents an effective tool to get insight on ternary fission from the observables selected.

In the last decades the primordial black holes ({\bf pbhs}) have attracted much attention of cosmologists and astrophysicists. This is associated with origination of such black holes in the early Universe as a result of a gravitational collapse of the high-density matter, making them natural ''detectors'' of the processes involved. In inflationary cosmology of particular importance are {\bf pbhs} originated during the pre-inflationary period. And, since they are small and generated at the energies close to the Planck energies, for them we should take into consideration the quantum-gravitational corrections ({\bf qgcs}). In turn, these corrections change (shift) the inflationary parameters. The paper presents a study of the above-mentioned shifts with regard to these corrections for different scenarios. It is shown that probabilities of occurrence of the {\bf pbhs} under study with due regard for the given {\bf qgcs} are rising as compared to the semiclassical consideration. Besides, high-energy deformations of Friedmann Equations created on the basis of these corrections have been derived for different patterns. Conclusion contains the general remarks concerning the above-mentioned {\bf qgcs} for cosmological parameters and perturbations due to inflation; the steps for their investigation are outlined and the key problems of such a study are formulated.

This study presents a detailed investigation of the application of superquadrics in small-angle scattering (SAS), a technique essential in materials science, biology, and physics for investigating structural properties at the nanoscale and microscale. Superquadrics, a family of geometric shapes known for their versatility in representing a wide range of forms, are employed to model complex structures in SAS studies. We examine the parametric nature of superquadrics and their ability to efficiently describe shapes from simple balls to intricate star-like forms. We demonstrate the application of superquadrics through a rigorous analysis of SAS simulated data, including scattering intensity patterns and pair-distance distribution functions. This allows us to reveal insights into key structural characteristics of various materials, such as the size and shape. We also demonstrate the efficacy of superquadrics in accurately modeling experimental small-angle X-ray scattering data from a chimeric protein complex, showcasing their potential in biological systems analysis. The findings offer a robust framework for future research and application in diverse fields, including materials science, nanotechnology, and bioengineering.

This study investigated a novel radioimmunotherapy strategy for targeting tumor angiogenesis. We developed a radiopharmaceutical complex by labeling an anti-adenosine triphosphate syn-thase (ATPS) monoclonal antibody (mAb) with the radioisotope 177Lu using DOTA as a chelating agent. 177Lu-DOTA-ATPS mAb demonstrated high labeling efficiency (99.0%) and stability in se-rum. MKN-45 cancer cells exhibited the highest cellular uptake, which could be specifically blocked by unlabeled ATPS mAb. In mice, 177Lu-DOTA-ATPS mAb accumulated significantly in tumors, with a tumor uptake of 16.0 ± 1.5%ID/g on day 7. 177Lu-DOTA-ATPS mAb treatment sig-nificantly reduced the viability of MKN-45 cells in a dose-dependent manner. In a xenograft tumor model, this radioimmunotherapy strategy led to substantial tumor growth inhibition (82.8%). Furthermore, combining 177Lu-DOTA-ATPS mAb with sunitinib, an anti-angiogenic drug, en-hanced the therapeutic efficacy of sunitinib in the mouse model. Our study successfully developed 177Lu-DOTA-ATPS mAb, a radioimmunotherapy agent targeting tumor blood vessels. This ap-proach demonstrates significant promise for inhibiting tumor growth, both as a single therapy and in combination with other anti-cancer drugs.

According to current forecasts, global heating is likely to exceed 2,8°C by the end of the century. This makes substantial adaptation measures necessary to secure a broad basis for livelihoods provision and the conservation of biodiversity. While the implementation of top-down and technocratic adaptation efforts is the majority, related adaptation shortcomings of socio-economic and ecological nature are becoming more and more apparent. Community-based adaptation (CBA) with its participatory, inclusive and needs-based bottom-up approach offers a promising and powerful alternative. This article uses a semi-systematic literature review approach to screen the current literature and identify core issues of CBA. Linking communality, locality, multidimensionality, power imbalances, transformative potential, localisation, the triad of adaptation metrics and adaptation with nature to corresponding potential actions for practical implementations provides a more holistic conceptualisation and broadens the horizons for further learnings, research and improved application.

A large core size and bending resistance are very important properties of mid-infrared energy transfer fibers, but large core sizes usually lead to a deterioration of bending properties. A negative-curvature nested node-free anti-resonant hollow-core fiber (AR-HCF) based on quartz is proposed. It was made by adding a nested layer to a previous AR-HCF design to provide an additional anti-resonance region while keeping the gap between adjacent tubes strictly correlated to the core diameter to produce a node-free structure. These features improve the fiber’s bending resistance while achieving a larger core diameter. The simulation results show that the radial air-glass anti-resonant layer is increased by the introduction of the nested anti-resonant tube, and the weak interference overlap between the fiber core and the cladding mode is reduced, so the fiber core’s limiting loss and the sensitivity to bending are effectively reduced. When the capillary wall thickness t of the fiber is 0.71 μm, the core diameter D is 70 μm, the ratio of the inner diameter of the cladding capillary to the core diameter d/D is 0.62, and the diameter of the nested tube is d0=29 μm, the fiber has a lower limiting loss at the wavelength of 2.79 μm, and the limiting loss is 3.28×10-4 dB/m. At the same time, the optimized structure also has good bending resistance. When the bending radius is 30 mm, the bending loss is only 4.72×10-2 dB/m. To our knowledge, this is the first research to achieve an anti-bending low-loss micro-structure hollow fiber with a bending radius of less than 30 mm in the 2.79 μm band. An anti-bending low-loss anti-resonant hollow-core fiber with this structure constitutes a reliable choice for the light guiding system of a 2.79 μm band erbium laser therapy instrument.

To reduce the cost of small wind turbines, a prototype of a butterfly wind turbine (6.92 m in diameter), a small vertical-axis type, was developed with many parts made of extruded aluminum suitable for mass production. An over-speed control system with movable arms that operated using centrifugal and aerodynamic forces was installed for further cost reduction. Introducing this mechanism eliminates the need for large active brakes and expands the operating wind speed range of the wind turbine. However, although the mechanism involving the use of only bearings is simple, the violent movement of the movable arms can be a challenge. To address this in the present study, dampers were introduced on the movable arm rotation axes to improve the movement of the movable arms. To predict the behavior of a movable arm and the performance of the wind turbine with the mechanism, a simulation method was developed based on the blade element momentum theory and the equation of motion of the movable arm system. Comparison of experiments and predictions with and without dampers demonstrated qualitative agreement. In the case with dampers, measurements confirmed the predicted increase in the rotor rotational speed when the shorter ailerons installed perpendicularly to the movable arms were used to achieve the inclination. The movable arm system with dampers is expected to be a useful device for vertical-axis wind turbines that are difficult to control.

Gliomas are common primary central nervous system (CNS) tumours which are often very difficult to diagnose, stage and manage because of their heterogeneity and molecular aberrations. The notable hallmark of gliomas is integrated genome mutations and methylome that correlates with distinctive patterns of transcription that potentiates glioma heterogeneity, angiogenesis and ultimately poor prognosis. The World Health Organization (WHO) has decided to reclassify gliomas based on molecular markers rather than the traditional anatomical basis; use of Nuclear Medicine techniques e.g. SPECT/PET and Magnetic Resonance Imaging (MRI) techniques based on molecular markers is set to become the future gold standards. This has led to the investigations on potential for the use of non-invasive imaging techniques such as [68Ga]68Ga-RGD positron emission tomography (PET) to be utilised routinely in clinical practice based on angiogenic markers and also the potential to add information that may assist in drug-design and therapeutic decision making. This review aims to provide an overview of the basis of recent advances in glioma imaging using molecular targeting with positron emission tomography and SPECT imaging, as well as the role in patient management i.e. diagnosis, staging, recurrence detection etc.

Pore structure characterization and fractal analysis have great significance for understanding and evaluating tight limestone reservoirs. In this work, the pore structure of tight limestone is characterized combined with low-temperature nitrogen adsorption (LTNA) and low-field nuclear magnetic resonance (NMR), and the fractal dimension of tight limestone pore structure is discussed based on LTNA and NMR data. The results indicate that the pores of tight limestone have H3 and H4 types, the pore size distribution (PSD) of H3 type is a wave distribution ranging from 2 to 10 nm, and the PSD of H4 type is a unimodal distribution ranging from 2 to 10 nm. The transverse relaxation time (T2) spectrum of tight limestone shows single peak (DF), double peak (SF) and three peak (TF), and the T2 spectrums for micropores, mesopores and macropores range from 0.1 to 10 ms, from 10 to 100 ms, and greater than 100 ms, respectively. The LTNA fractal dimension of tight limestone (DL) ranges between 2.4446 and 2.7688, with an average of 2.5729, and the NMR fractal dimensions of micropores (DNMR1), mesopores (DNMR2) and macropores (DNMR3) are distributed between 0.3744 to 1.1293, 2.4263 to 2.9395 and 2.6582 to 2.9989, respectively. Moreover, there is no correlation between fractal dimension and permeability and porosity, a negative correlation between DL and average pore radius, a positive correlation between DL and specific surface area, and a positive correlation between DNMR2 and DNMR3 and micropore content, while DNMR2 and DNMR3 are negatively correlated with the content of mesopores and macropores.

Interest grows in designing silicon-on-insulator slot waveguides to trap optical fields in subwavelength-scale slots and developing their optofluidic devices. However, it is worth noting that the inherent limitations of the waveguide structures may result in high optical losses and short optical paths, which challenge the device performance in optofluidics. Incorporating the planar silicon-based slot waveguide concept into a silica-based hollow-core fiber can provide a perfect solution to realize an efficient optofluidic waveguide. Here we propose a subwavelength-scale liquid-core hybrid fiber (LCHF), where the core is filled with carbon disulfide and surrounded by a silicon ring in a silica background. The waveguide properties and the Stimulated Raman Scattering (SRS) effect in the LCHF are investigated. The fraction of power inside the core of 56.3% allows an improved sensitivity in optical sensing; while the modal Raman gain of 23.60 m-1·W-1 is 2 times larger than that generated around a nano fiber with the interaction between the evanescent optical field and the surrounding Raman media benzene-methanol, which enables a significant low-threshold SRS effect. Besides, this in-fiber structure features compactness, robustness, flexibility, ease of implementation in both trace sample consumption and reasonable liquid filling duration, as well as compatibility with optical fiber systems. The detailed analyses of the properties and utilizations of the LCHF suggest a promising in-fiber optofluidic platform, which provides a novel insight into optofluidic devices, optical sensing, nonlinear optics, etc.

In this paper, we consider the behavior of the local energy flow velocity of the fundamental air – core mode at the core – cladding boundary in two types of hollow – core fibers: hollow – core fibers with a negative curvature of the core boundary and single – capillary fibers with similar geometrical parameters. It is demonstrated that the behavior of both axial and radial components of the local energy velocity of the fundamental air – core mode is completely different for these two types of hollow – core fibers. The negative curvature of the core boundary leads to an alternating behavior of the radial projection of the local energy velocity and a decrease by two orders of magnitude compared to the values of this projection for a single capillary. In our opinion, this behavior of the local energy velocity of the fundamental air – core mode is caused by a periodic set of Poynting vector vortices that appear in the cladding capillary walls.

A new class of nano-cube core-shell heterostructures containing Ag coating on the top of WO₃ was fabricated. Physical vapor deposition was used to produce WO₃ based nano-heterostructures. All kind of wet toxic chemical process was avoided to make the process simple and contaminant free. Sputtering of WO₃ and a subsequent thermal annealing process was done to create nano-cubes of WO₃. After that, sputtering of Ag was performed to form the Ag-WO₃ core-shell nano-heterostructures (CSNH). The CSNHs were characterized using field emission scanning electron microscopy (FESEM), energy dispersive spectroscopy (EDS), X-ray diffraction analysis (XRD) and UV-vis spectroscopy. The morphologies, elemental analysis, interfaces, crystallinity, phases, and chemical compositions were analyzed. The bottom-up growth of WO₃ nanocubes was studied using different time periods at 900°C. Ag coating was also studied before and after annealing. Finally, an optical property (band gap) was also analyzed using Tauc plot derive from absorption spectra. The tailoring the band gap of WO₃ from ~2.9eV to ~ 2.45 eV was observed while Ag-WO₃ CSNH formed.

Nowadays, inquiries are one of the most important tasks to be executed in order to get valued information. When an inquiry is done to gather information about a human behavior there are some problems inherent to it. One of the main problems is how the information about many different persons can be processed to give good information about their environment. Most of the information gathered by these inquiries is used to analyze the behavior of the respondents. It can be used to estimate the success of a certain product on the market or just to validate the satisfaction of current costumers. The veracity of this information can be critical to model environments with some acceptable level of precision. Modelling environments through Artificial Neural Networks (ANN) is highly common because ANN’s are excellent to model predictable environments using a set of data. ANN’s are good in deal with sets of data with some noise, but they are fundamentally surjective mathematical functions and they aren’t able to give different results for the same input. So if an ANN is trained using data where the same input has different images which can be the case of survey data, this can be a problem for the success of modelling the environment. Therefore is necessary to process the data in order to adjust and eliminate invalid data.

With reference to electromagnetic interaction and Abdus Salam’s strong (nuclear) gravity, 1) Square root of ‘reciprocal’ of the strong coupling constant can be considered as the strength of nuclear elementary charge. 2) ‘Reciprocal’ of the strong coupling constant can be considered as the maximum strength of nuclear binding energy. 3) In deuteron, strength of nuclear binding energy is around unity and there exists no strong interaction in between neutron and proton. $G_s\cong 3.32688\times {10}^{28}{\mathrm{m}}^3{\mathrm{kg}}^{-1}{\sec }^{-2}$ being the nuclear gravitational constant, nuclear charge radius can be shown to be, $R_0\cong \frac{2G_s{m}_p}{c^2}\cong 1.24\mathrm{fm}.$ $e_s\cong \left(\frac{G_s{m}_p^2}{\hslash c}\right)e\cong 4.716785\times {10}^{-19}\mathrm{C}$ being the nuclear elementary charge, proton magnetic moment can be shown to be, ${\mu }_p\cong \frac{e_s\hslash }{2m_p}\cong \frac{e{G}_s{m}_p}{2c}\cong 1.48694\times {10}^{-26}\mathrm{J}{.\mathrm{T}}^{-1}.$ ${\alpha }_s\cong {\left(\frac{\hslash c}{G_s{m}_p^2}\right)}^2\cong 0.1153795$ being the strong coupling constant, strong interaction range can be shown to be proportional to $\exp \left(\frac{1}{{\alpha }_s^2}\right).$ Interesting points to be noted are: An increase in the value of ${\alpha }_s$ helps in decreasing the interaction range indicating a more strongly bound nuclear system. A decrease in the value of ${\alpha }_s$ helps in increasing the interaction range indicating a more weakly bound nuclear system. From $Z\cong 30$ onwards, close to stable mass numbers, nuclear binding energy can be addressed with, ${\left(B\right)}_{A_s}\cong Z\times \left\{\left(\frac{1}{{\alpha }_s}+1\right)+\sqrt{\sqrt{30\times 31}}\right\}\left(m_n-m_p\right)c^2\approx Z\times 19.66\mathrm{MeV}.$ With further study, magnitude of the Newtonian gravitational constant can be estimated with nuclear elementary physical constants. One sample relation is, $\left(\frac{G_N}{G_s}\right)\cong \frac{1}{2}{\left(\frac{m_e}{m_p}\right)}^{10}\left[\sqrt{\frac{G_F}{\hslash c}}/\left(\frac{\hslash }{m_{e}c}\right)\right]$ where $G_N$ represents the Newtonian gravitational constant and $G_F$ represents the Fermi’s weak coupling constant. Two interesting coincidences are, ${\left(m_p/m_e\right)}^{10}\cong \exp \left(1/{\alpha }_s^2\right)$ and $2G_s{m}_e/c^2\cong \sqrt{G_F/\hslash c}.$

The direct detection of dark matter constituents, in particular the weakly interacting massive particles (WIMPs), is central to particle physics and cosmology. In this paper we develop the formalism for WIMP-Nucleus induced transitions from isomeric nuclear states. We specialize it in the case of the experimentally interesting target 180 Ta

We are witnessing a progressive divestment of some institutions with strong traditions and skills in physical modelling and their consequent impoverishment, to the detriment of numerical modelling. For many reasons, the economic imperatives and the exponential growth of computational means and numerical methods should certainly not be excluded. In this work, we aimed to highlight the new requirements of the recent sophisticated developments in physical modelling, precisely due to the new needs imposed on them by mathematical and numerical modelling and the growing risks in civil construction works. In this context, reflections are reported, justified by scientific and real-world examples, on the need for maintenance and reinforcement of investments in physical modelling, both to support the scientific community and to design buildings of significant economic, social and environmental impact.