Asphaltene-resin-paraffin deposition (ARPD) is a complicated and prevalent issue in oil and gas industry, impacting the efficiency, integrity of petroleum extraction, production, transportation and processing systems. Considering all witnessed ARPD problems in Azerbaijan oil fields, this paper proposed a chemical method and optimized the type and the concentration of chemical inhibitors. And then the effect of selected chemical reagent on inhibiting the ARPD amount and thus en-hancing oil recovery was detected by reservoir simulation during both waterflooding and CO2 flooding production. Three new chemical compounds (namely, Chemical-A, Chemical-B and Chemical-C) were examined in laboratory conditions and their impact on rheological properties of high-paraffin oilfield samples of Azerbaijan (X, Y and Z) were investigated. Experimental results show that Chemical-C with concentration of 600 g/t has the best efficiency for alleviating the problems. After adding Chemical-C to the crude oil, the freezing point of oil is decreased from 12 °C to (-4) °C, ARPD amount is declined from 0.185 to 0.016 g and oil effective viscosity is reduced from 16.2 mPa·s to 3.1 mPa·s. It is determined that for water and CO2 flooding, higher injection pressure resulted in reduced asphaltene precipitation. Adding selected ARPD inhibitor, the oil recovery for waterflooding can increase from 52% to 62%, while it can rise from 55% to 68% for CO2 flooding.

In this work, the properties of a composition based on synthetic rubber ethylene-propylene ter-polymer and polymers with functional groups of the mixture are studied. Low efficiency of some compositions based on ethylene and propylene copolymer limits their use in the production of tires and rubber products. Therefore, we conducted a study to improve the disadvantages of SREPT-60 using butyl rubber + choro polyisoprene + butadiene-nitrile + butadiene styrene rubber and adding a plasticizer to the composition = α, methacrylate-(bis-diethylene glycol phthalate) -(btegf-9) The data obtained showed that a number of its indicators of rubber based on them were improved. Tear resistance, resistance to repeated stretching increased, adhesion of the composition to metal, chemical resistance increased, the degree of swelling in benzene and gasoline-benzene mixture decreased. Compositions based on the mixture SREPT-60 using butyl rubber + choro polyisoprene + butadiene-nitrile + butadiene styrene rubber and adding a plasticizer to the composition = α, methacrylate-(bis-diethylene glycol phthalate) -(btegf-9) +Dioctyl phthalate: (70:20:10) have high resistance to swelling in an aggressive environment (Benzene, gasoline, alcohol, acid, oil, etc.) mixture.

In eastern part of Ethiopia groundnut is very commonly intercropped with sorghum. Even though intercropping of sorghum with groundnut is practiced in the eastern part of Ethiopia the population density at what ratio should not be known. Therefore determining the population ratio is found to be crucial to draw management options. The study was conducted at two locations at Fadis (on station) and Babile (sub- station). Sorghum variety (Teshale) and groundnut (Fetene) were used as planting materials. All agronomic data were collected and analyzed by using GenStat software. Significant different were obtained among the treatments. The research result showed that, there were significance difference for both sorghum and ground nut yield per hectare in the years (2014 and 2015) among treatments. The result over time(in 2014 and 2015) at Fadis and Erer showed that the highest sorghum and groundnut yield per hectare were obtained/harvested from the intra row spacing of 25cmx20cm and 30cmx20cm intercropping sorghum with ground nut system with (1.27 and 1.31) respectively. The highest LER (1.31) and highest GMV (10218.00 ETBr/ha) were obtained from the intercropping of 30cmx20cm (Sorghum & groundnut). Clearly showed that, with intercropping of sorghum and Groundnut, it is possible to produce additional yield of sorghum without significant reduction in groundnut yield. As a result of this, the intra spacing of the main crop (sorghum) 25cm and 30cm and for the subsidiary crop (groundnut) 20cm was recommended for further production in the study areas of eastern Harerghe zone and similar agro-ecologies.

Accurate assessment of shale gas reserves hinges on a detailed characterization of gas and water distribution within shale reservoirs. Despite its importance, the nanoscale behavior of water and methane in deep shale formations, especially under elevated temperatures and pressures, remains poorly understood. This study proposes a novel molecular modeling approach to represent the complex nanocomposite porous media found in deep shale matrices. Leveraging quantitative data from experimental analyses of shale pore composition, we developed a molecular model that accurately reflects the intricate pore-slit structure within a composite of kerogen and illite, common constituents of shale. Employing a hybrid grand canonical Monte Carlo and molecular dynamics simulation technique, we investigated the micro-scale distribution and preferential adsorption sites of water and methane within the shale matrix. Our research further elucidates the impact of water on the pore structure of shale and delineates the co-occurrence patterns of water and methane. The simulations reveal that water and methane share similar adsorption preferences on kerogen surfaces, while methane does not exhibit specific adsorption preferences on water-bearing illite. We also find that the presence of water significantly alters the illite pore space, leading to a reduction in larger pore volumes and a concomitant increase in smaller pores. The decrease in methane content with increasing water content is more pronounced in the shrinkage cracks compared to the kerogen matrix pores and is particularly notable in the macropores of illite. The findings underscore the differential sensitivity of methane content to water levels across various shale pore types. These insights contribute to a deeper theoretical understanding of gas and water distribution mechanisms in deep shale reservoirs, offering valuable support for the evaluation of deep shale gas resource potential.

: This study focuses on optimizing chlorophyll extraction techniques and strategically placing leaf disks to enhance chlorophyll concentration in sesame (Sesamum indicum L.) leaves. Thirty sesame genotypes, categorized into light green (LG), middle green (MG), and deep green (DG) pigment groups based on leaf coloration, were selected from a larger pool of field-grown accessions. The investigation involved determining optimal SPAD value index measurements, quantifying pigment concentrations, exploring extraction solvents, and selecting suitable leaf disk positions. Significant variations in chlorophyll content were observed across genotypes, greenness categories, and leaf disk positions. The categorization of genotypes into DG, MG, and LG groups revealed a correlation between leaf appearance and chlorophyll content. The study highlighted a consistent relationship between carotenoids and chlorophyll, indicating their role in adaptation to warm environments. Examination of leaf disk positions revealed a significant chlorophyll gradient along the leaf blade, emphasizing the need for standardized protocols. Chlorophyll extraction experiments identified DMSO and 96% ethanol, particularly the later incubated for 10 minutes at 85°C, as effective choices. This recommendation considers factors like cost-effectiveness, time efficiency, safety, and environmental regulations, ensuring consistent and simplified extraction processes. For higher chlorophyll extraction, focusing on leaf tips and the 75% position along the sesame leaf blade is suggested, consistently yielding higher chlorophyll content. Our findings therefore, underscores insightful knowledge on chlorophyll gradients and encouraging for standardized protocols, that enabling researchers to refine experimental designs for precise and comparable chlorophyll measurements. Recommended solvent choices ensure reliable outcomes in plant physiology, ecology, and environmental studies.

Network Function Virtualization (NFV) allows for the dynamic provisioning of Virtualized Network Functions, adapting services to the complex and real-time network environment for enhanced network performance. Despite the benefits of NFV, virtual network functions (VNFs) migration and the energy consumption pose significant challenges due to the dynamic nature of the physical network, especially in the edge-cloud continuum network. Currently, people tackle this challenge by predicting the network traffic and then proactively migrating the VNFs using the predicted values. There are two challenges here. First, when SFCs belong to different network service providers, the historical network traffic data is held by the service providers, and they are reluctant to share the historical data due to privacy concerns. Without the historical network traffic data of each SFC, the resource provider that owns the underlying network cannot effectively predict the network traffic; in addition, without the feedback of the migration results of the underlying physical network, the network traffic prediction will be difficult to match the needs of the physical network. In this manuscript, we solve the problem of network traffic prediction in the NFV-based edge-cloud continuum network for multiple network service providers. We aim to improve migration performance and reduce energy consumption while ensuring resource and latency requirements. To protect the privacy of each network service provider, we apply an FL algorithm. After that, to improve the migration performance, we tailor the loss function. In the loss function, factors such as the number of migrations, the number of migration failures, and the energy consumption of the NFV-based edge-cloud continuum network are added. Additionally, to obtain the results of the SFC migration, we develop a mathematical model for the problem of multiple network service providers in the NFV-based network. The effectiveness of our algorithm is evaluated through extensive simulations, and the results show a significant reduction in the number of migrated nodes and energy consumption while improving the SFC acceptance ratio compared to state-of-the-art schemes which only use the difference between predicted and actual flows to define the loss function.

Carbon dioxide (CO2)miscible fracturing huff and puff technology plays a pivotal role in enhancing the recovery rate of crude oil, particularly in reservoirs with challenging physical properties, strong water sensitivity, high injection pressure, and complex water injection dynamics. In this study, the oil-increasing mechanism and huff and puff effect of CO2 miscible fracturing fluid are investigated through a comprehensive experimental approach. Specifically, experiments on PVT gas injection expansion, minimum miscible pressure, and CO2 miscible fracturing huff and puff are conducted on the G fault block reservoir in J Oilfield. The findings demonstrate that injecting CO2 into reservoirs leads to oil volume expansion, viscosity reduction, and saturation pressure increase. Additionally, the inclusion of solubilizers and viscosity reducers further enhances the efficiency of crude oil extraction. Solubilizers not only improve oil recovery but also reduce the minimum miscible pressure required for effective CO2 dispersion. Furthermore, the shut-in time, permeability, and huff and puff method all have considerable impacts on huff and puff recovery rate. This study offers valuable technical insights, supporting the application of CO2 miscible fracturing huff and puff technology to enhance oil recovery in low-permeability reservoirs.

Mineral nutrition is essential for plant growth and interaction of plants with biotic and abiotic stresses. Mango twig-tip dieback (MTTD) is a new type of mango decline, but its impact on the trees’ mineral nutrition is unknown. This study was conducted to determine the effect of MTTD infection on the nutrient status, balance, and resorption efficiency (RE) of mango. Leaf nutrient concentrations and deviation from the optimum percentage (DOP) indices of ‘Kensington Pride’ (KP) mango trees with low (LD) and high (HD) levels of MTTD infections were analyzed to compare the foliar nutrition status and nutrient balance between the LD and HD trees. Moreover, the nutrient resorption efficiency of MTTD-infected dried leaves (RE_D) was compared with the resorption efficiency of healthy (RE_S) leaves of KP mangoes. The concentrations of the total Ca, Mg, Cu, Fe, Mn, and Zn were lower in the HD trees than in the LD trees. But the total K content was higher in the HD trees, and its DOP index was sufficient, while the total K concentration was low and deficient level in LD trees. Moreover, DOP indices for total Ca, Mn, and Zn were less deficient in LD trees than in HD trees, and overall nutrient imbalances were exacerbated in HD trees. RE_D was significantly lower than RE_S for the total N, P, S, Cu, Fe, and Zn but significantly higher than RE_S for K. The study underscores the significant influence of MTTD on the mineral nutrition of KP mangoes, revealing distinct nutrient variations between trees with low and high MTTD infection levels. These findings have important implications for mango crop management, emphasizing the need for targeted nutrient interventions to address imbalances induced by MTTD and enhance the overall health and resistance of mango trees against MTTD infection.

In the process of oil and gas development and production, when the flow rate in the wellbore is large, the materials underground will be eroded, causing the operation to be unable to proceed smoothly and reducing the efficiency of oil and gas production. Therefore, optimizing the anti-erosion coating under high-speed flow conditions in wellbore is a very interesting thing. It can greatly improve operational efficiency. In this paper, laser cladding was used to prepare the new coating used in the PDC drill bit. Then, the effects of tungsten carbide and multi-layer graphene on the microstructure and properties of the tungsten carbide coating were studied. The research results indicate that, for new coatings, 60% tungsten carbide and 0.3% graphene are the optimal ratios. After adding WC, the hardness has significantly improved. However, when the WC content further increases more than 30%, the increase in hardness is relatively small. In addition, when the content of graphene is more than 0.3%, the branched structure became thicker, and not only the segregation of Cr, Si and W became very obvious again, but also the segregation of Fe occurred at the Ni enrichment site. The research results contribute to improving oil and gas production and operational efficiency under high-speed fluid flow conditions in the wellbore.

Superior fiber quality is one of the most important objectives in cotton breeding. To detect the genetic basis underlying fiber quality, an F2 population containing 413 plants was constructed by crossing Jifeng 914 and Jifeng 173, both of which have superior fiber quality, with Jifeng 173 being better. Five fiber quality traits were investigated in the F2, F2:3, F2:4, and F2:5 populations. Quantitative trait loci (QTL) mapping was conducted based on a high-density genetic map containing 11,488 single nucleotide polymorphisms (SNPs) and spanning 4,202.12 cM in length. Transgressive segregation patterns and complex correlations in the five tested traits were observed. A total of 108 QTLs were found, including 27 for fiber length (FL), 16 for fiber strength (FS), 24 for micronaire (MC), 17 for fiber uniformity (FU), and 24 for fiber elongation rate (FE). Chromosome A7 contained 12 QTL, ranking the first. No QTL was found on chromosome D1 and D11. Each QTL contributed 1.98%–21.45% to the phenotypic variation (PV), including 13 major effect QTLs that contributed more than 10% toward PV. Two QTLs could be repeatedly detected in three populations, including qFL-D3-2 in F2, F2:4, and F2:5 with 9.18%–21.45% of PV, qFS-A11-1 in F2:3, F2:4 and F2:5 with 6.05%–10.41% of PV. Another seven stable QTLs could be detected in two populations, including four major effect QTLs: qFL-A12-3, qFS-D10-2, qMC-D6-2, and qMC-D8-1. Fourteen QTL-overlapping regions were found, which might explain the complex correlations among the five phenotypic traits. Four regions on chromosome A11, D3, D6, and D10 covered by both stable and major effect QTLs are promising for further fine mapping. The genomic regions of the two QTLs detected in three populations and the four major effect QTLs contain 810 genes. Gene functional analysis revealed that the annotated genes are mainly involved in protein binding and metabolic pathways. Fifteen candidate genes in the qFL-D3-2 region are highly expressed in fiber or ovules during fiber initiation, elongation, secondary cell wall thickening, or maturation stages. qRT-PCR revealed that Ghir_D03G005440.1 and Ghir_D03G011310.1 may play a role in promoting fiber initiation, Ghir_D03G006470.1 may be beneficial for promoting fiber elongation. This study provides more information for revealing the molecular genetic basis underlying cotton fiber quality.

This study aims to investigate the interfacial tension, emulsion stability, and the impact on oil displacement effectiveness of mixed systems containing nonionic surfactants and amphoteric surfactants at different ratios. To achieve this, three different emulsion stability formulations were prepared by mixing betaine and nonionic surfactants in ratios of 1:1, 3:2, and 3:1 respectively. By adjusting the proportions of betaine and nonionic surfactants, variations in interfacial tension and emulsion formation among the three mixed systems were studied to analyze the mechanism of interaction between betaine and nonionic surfactants and evaluate their effects on crude oil displacement and enhanced oil recovery in reservoirs. Subsequently, microscopic and macroscopic oil displacement experiments were conducted on the three mixed systems, along with experiments on emulsion flow resistance. The aim was to verify the oil displacement effectiveness of different mixed systems and further understand their potential applications in reservoirs. By comprehensively analyzing the experimental results, optimal ratios and conditions for the mixed systems were determined. The experimental results indicate that the emulsification system formed by mixing betaine and nonionic surfactants at a ratio of 3:1 achieves molecular synergies through electrostatic interactions and mixed adsorption with betaine, resulting in a compact arrangement of interface membranes and demonstrating a synergistic effect in reducing interfacial tension to an ultra-low value of 10 -4 mN/m. Additionally, as the proportion of betaine surfactant increases, the viscosity of the aqueous phase liquid film increases, the rate of thinning of the liquid film slows down, the rate of water release slows down, and the stability of the emulsion increases. Microscopic oil displacement experiments verified that the three mixed systems increase oil washing efficiency through low interfacial tension and emulsification stripping action, thereby increasing the oil displacement mechanism's coefficient. Emulsion flow resistance experiments demonstrated that as the proportion of betaine surfactant increases, the system exhibits better plugging ability. However, macroscopic oil displacement experiments revealed differences in compatibility between different emulsion stability solutions and rocks with different permeabilities. The mixed system of betaine and nonionic surfactants at a ratio of 3:1 exhibits the best emulsification plugging ability in rocks with a permeability of 109mD, while the 1:1 mixed system performs best in rocks with a permeability of 12mD. This holds significant theoretical and practical significance for reservoir development and enhanced production.

The extensive use of polypropylene (PP) in various industries has heightened interest in devel-oping efficient methods for recycling and optimising its mixtures. This study focuses on formu-lating predictive models for the Melt Flow Rate (MFR) and shear viscosity of PP blends. The in-vestigation involved characterising various grades, including virgin homopolymers, copolymers, and post-consumer recyclates, in accordance with ISO 1133 standards. The research examined both binary and ternary blends, utilising traditional mixing rules and symbolic regression to predict rheological properties. High accuracy was achieved with the Arrhenius and Cragoe models, at-taining R² values over 0.99. Symbolic regression further enhanced these models, offering signif-icant improvements. To mitigate overfitting, empirical noise and variable swapping were in-troduced, increasing the models' robustness and generalisability. The results demonstrated that the developed models could reliably predict MFR and shear viscosity, providing a valuable tool for improving the quality and consistency of PP mixtures. These advancements support the de-velopment of recycling technologies and sustainable practices in the polymer industry by opti-mising processing and enhancing the use of recycled materials.

This paper addresses the lack of analytical tools for visual data analysis in IEEE Xplore, an abstract database of publications on technical problems in electronics and electrical engineering. The openness of the platform and the good fillability of a large number of bibliometric record fields make it attractive for visual data analysis. The topic of machine learning and artificial intelligence applied to power systems, which are critical issues in the energy transition process, is chosen as an example for visual data analysis. The programs and utilities used for data analysis were VOSviewer, Scimago Graphica, FP-Growth algorithm, Inkscape, and MultiDendrograms. The use of IEEE Terms field data to identify publication topics in the exported data is analyzed in the most comprehensive way. This paper can be considered a reference for professionals interested in bibliometric analysis and visualization of IEEE Xplore data.

Objectives. The aim of the study is to identify relevant research topics based on pooled bibliometric data of International Journal of Hydrogen Energy publications from 2022-2024, collected from The Lens and ScienceDirect platforms. Data source. Bibliometric records of International Journal of Hydrogen Energy articles published in 2022-2024 from The Lens and ScienceDirect platforms were used. Programs and utilities used. VOSviewer, Scimago Graphica, Inkscape, FP-growth utility. Results. The study showed the feasibility of merging bibliometric records from the open platforms ScienceDirect and The Lens, which complement each other. The 'Fields of Study' data of The Lens can be rationally interpreted as system keywords similar to Scopus Index Keywords. The possibility of using 'Fields of Study' data in a method similar to bibliographic coupling is shown. The practicality of using an Alluvial diagram to show the co-occurrence of the four terms was demonstrated. The study also emphasizes the advisability of joint use of VOSviewer and Scimago Graphica programs for complex visualization of bibliometric analysis results. The study identified two dominant publication topics in International Journal of Hydrogen Energy for 2022-2024, which can be described in terms of: 'Catalysis, Hydrogen, Physical_chemistry, Chemical_engineering, Nanotechnology, Electrochemistry, Organic_chemistry, Materials_science' and 'Electrical_engineering, Hydrogen_production, Renewable_energy, Environmental_science, Hydrogen_economy, Hydrogen, Engineering'.

Objectives. The aim of this study was to demonstrate the ability to visualize the results of the Scilit platform's bibliometric data analysis on the topic "AI & Machine Learning" to identify publications reflecting specific issues of the topic. Data source. Bibliometric records exported from the Scilit platform on the topic "AI & Machine Learning" for the years 2021–2023 were used. For each year, 6,000 records were downloaded in CSV and RIS format. Programs and utilities used. VOSviewer, Scimago Graphica, Inkscape, FP-growth utility, GSDMM algorithm. Used services: Elicit, QuillBot, Litmaps. Results. It has been shown that bibliometric data from the open access abstract database Scilit can serve as a quality alternative to subscription-only databases. Data exported from the Scilit platform require preprocessing to make them available in a format that can be processed by programs such as VOSviewer and Scimago Graphica. The use of GSDMM and FP-growth algorithms is effective for structuring bibliometric data for further visualization. The Scimago Graphica software provides wide possibilities for building compound diagrams, in particular, for representing the network of keywords in such important coordinates for bibliometric analysis as average year of publication and average normalized citation, as well as for building an alluvial diagram of co-occurrence of more than two keywords. The possibility of using such services as elicit.com, quillbot.com and app.litmaps.com to accelerate the selection of publications on the topic under study is shown.

Background. Keyword co-occurrence analysis is a crucial tool for comprehending research trends, identifying relevant studies, and gaining insight into the connections between various concepts and topics. Objective. This study focuses on analyzing the co-occurrence of keywords using FP-growth algorithm and direct search methods. Materials and methods. The methodology involved extracting bibliometric data of Energies journal for 2023-2024 from MDPI publisher platform, keyword lemmatization and keyword co-occurrence estimation. Clustering and visualization were performed using Multidendrograms and Scimago Graphica software. Results. The results showed that the FP-growth algorithm can achieve a close match with the direct search results, which facilitates data preparation for clustering. In addition, finding the co-occurrence of three or more keywords significantly reduced the number of possible combinations, which allowed the identification of specific research topics. Conclusions. This study highlights the usefulness of the FP-growth algorithm in keyword analysis and provides insights into ways to refine search queries to abstract databases for the purpose of designing and writing literature and systematic reviews.

Relevance of the subject. Keyword selection is critical to finding relevant literature and requires justification for querying abstract databases and other sources to ensure accuracy and completeness. The topic of Energy Systems is of great importance due to the introduction of renewable energy sources, modern control methods, and complex energy systems during the energy transition. The aim of this study. The goal of this paper was to identify keywords that would be useful to subject matter experts when collecting literature on a particular topic, based on entries in the IEEE Terms field. Data. Bibliometric data were exported from the IEEE Xplore platform in the following order: for 2019-2023, 2000 records sorted by relevance, for 2024, 1680 records current as of April 11, 2024. Analytical methods applied and software used. VOSviewer, Scimago Graphica implementing the Clauset-Newman-Moore algorithm and agglomerative hierarchical clustering method implemented in Multidendrograms. Results. The main issues of the Energy Systems topic are presented in tabular and graphical formats. The fpgrowth utility offers flexible data preparation options, which makes it worthwhile to conduct a separate study to analyze the score of co-occurrence terms given by its algorithm.

Purpose of publication: - Preparation of bibliometric data exported from the Scilit platform on energy efficiency and conservation for further analysis to identify relevant research topics. - To identify potential issues in the processing of data exported from the Scilit platform. - Providing colleagues with the opportunity to use the prepared data and examples of their analysis for independent research on topical issues of energy efficiency and energy conservation using materials provided by the Scilit platform. Research Materials: Files in CSV and RIS formats exported from Scilit for the query "energy conservation OR efficiency" in Common Fields [Title, Abstract, Keyword], using filters: Content Type → Journal Article; Year→2021-2023; Subject → Industrial Engineering (29.8K), Energy and Fuel Technology (9.8K), Manufacturing Engineering (9.2K). A total of 30K records sorted by their relevance (10K for each year) were exported. Data are current as of 14-03-2024. Methods: Preprocessing of title, annotation, and keyword field texts using lemmatization dictionaries collected on GitHub, removal of keywords taken from GATE and spaCy, and "manual" editing. Using VOSviewer to analyze publication topics by clustering keywords based on their co-occurrence. Using Scimago Graphica to build bubble diagrams.Application of the GSDMM algorithm for clustering bibliometric records by title and annotation texts. Creation of a dictionary for this algorithm using the keyword field.Use of the Carrot2 demo version and the NMF algorithm for a more detailed analysis of the topics of the record clusters obtained from GSDMM. Results: are presented in the form of initial and interim tables and graphs obtained in the course of this study. The full tables are provided as references to the attached materials. Supplementary material for this preprint on figshare: Chigarev, Boris (2024). Supplementary material for preprint "Analyzing the Possibilities of Using the Scilit Platform to Identify Current Energy Efficiency and Conservation Issues". figshare. Dataset. https://doi.org/10.6084/m9.figshare.25574058.v1

The ASEAN Community-based Tourism (CBT) Standard has been adopted by 10 ASEAN member states in 2016 in order to collectively promote ASEAN as a competitive community-based tourism destination. Among the ASEAN member states, Lao PDR (Laos), has a unique CBT development experience through collaboration with various international development agencies. Such history has brought about issues when ASEAN CBT Standard was implemented at to provincial and district levels in Laos, including concerns of related communities on the Standard being not easily applicable considering the state of tourism development. While the application of the regional standard is a significant issue to the tourism industries in the Member States, however, there has been a lack of studies regarding the dynamics of implementation of regional tourism standards at the national level. In order to fill the research gap, this study utilized in-depth interviews with seven executives with significant experiences from the government, international development agency, international organization, and the private sector. Interviewees projected a diversity of perspectives on enabling factors and challenges in implementing ASEAN Community-based Tourism Standard at the national level focusing on Laos, which showed the complexity of CBT dynamics. The results also revealed how regional standards can be further recognized and promoted to the key stakeholders of Laos, better accepted and utilized by end users, and possibly better customized according to the local circumstances. Findings of this study evidence that collaboration among key stakeholders and the expected role of these stakeholders are critical when implementing ASEAN CBT Standard.

Accurate forecasting of available energy portion that corresponds to the reservoir inflow of the month(s) ahead provides important decision support for the hydropower plants in energy pro-duction planning for revenue maximization, as well as for the environmental impact prevention, and flood control at the upstream and downstream of a basin. Therefore, a reliable forecasting tool or model is deemed necessary and crucial. Considering the fluctuation and nonlinearity of data which significantly influence the forecasting results, this study develops an effective hybrid model by integrating Artificial Neural Network (ANN) and Particle Swarm Optimization (PSO) called “PSO-ANN” model based on the hydrological and meteorological data pre-processed by cross-correlation function (CCF), autocorrelation function (AFC), and normalization techniques for predicting the available energy portion corresponding to the reservoir inflow mentioned above for a case study hydropower plant in Laos namely, Theun-Hinboun hydropower plant (THHP). The model was evaluated by using correlation coefficient (r), relative error (RE), root mean square error (RMSE), and Taylor diagram plots in comparison with the popular single algorithm approaches such as ANN, and NARX models. Results demonstrated the superiority of the proposed PSO-ANN approach over the other two models.

With the offshore oil-gas fields entering decline phase, high-efficiency separation of oil-gas-water mixtures becomes a significant challenge. As essential equipment for separation, the three-phase separators play a key role in Offshore Oil-Gas production. However, level control is critical in the operation of three-phase gravity separators on offshore facilities, as it directly affects the efficacy and safety of the separation process. This paper introduces an advanced deep deterministic policy gradient with adaptive learning rate weights (ALRW-DDPG) control algorithm, which improves the convergence and stability of the conventional DDPG algorithm. An adaptive learning rate weight function is meticulously designed, and an ALRW-DDPG algorithm network is constructed for simulating three-phase separator liquid level control. The effectiveness of the ALRW-DDPG algorithm is subsequently validated through simulation experiments. The results show that the ALRW-DDPG algorithm achieves a 15.38% improvement in convergence rate compared to the traditional DDPG algorithm, and the control error is significantly smaller than that of PID and DDPG algorithms.

Risk management for technological hazards mainly focuses on the consequences on human lives. Although technological risk analysis evaluates environmental vulnerability, it does not reflect the consequences on environmentally exposed elements, such as rivers, water springs, flora, and fauna. This paper's objective was to propose a conceptual framework and create a multidisciplinary evaluation model for environmental risk analysis in the oil and gas industry. Initially, the problem was approached from a global perspective to justify the necessity of a holistic environmental risk analysis methodology in the oil industry, using environmental risk factors as well as underlying factors, such as environmental fragility and lack of resilience. The holistic assessment was carried out based on probabilistic risk analysis methodologies to obtain a holistic environmental risk index, HERI. This methodology was applied to an oil and gas industry company in Colombia. This allowed greater disaggregation of the results to establish priorities for risk reduction actions and identify the company's weaknesses.

Several studies have highlighted the importance and evolution of process safety leadership and culture in various industries. However, none has focused on the palm oil milling industry yet. This paper critically reviews the latest developments in the palm oil milling process and unit operations leading to process safety concerns. It also discusses the Principle of 3C that is applied to explain repeat accidents and the four-level safety culture in the palm oil milling industry. For this purpose, the author presents case studies of two key palm oil companies in Malaysia. Overall, this paper offers guidelines to leaders in the palm oil milling industry about the required process safety leadership and culture to be understood in order to improve their safety outcomes.

The research presented in this article is based on a strategic approach to a rural area in the mountainous region of Romania and is underwritten by specialists in the economy of mountainous regions in order to elaborate relevant solutions to complex problems relating to sustainable development. In essence, the research underlines and promotes the particularities of performing research for the identification and valuation of endogenous resources, that is, creating relevant strategic options for the durable development of the mountainous region, centered on the renewal of economic activities related to the existent endogenous resources, by using methods, work techniques, and instruments of strategic analysis. These factors are subordinate to the process of harmonization to the requirements of community development and environmental protection according to the new strategy for the development of the European Union 2020 (European Green Pact). This pact also emphasizes the necessity of involving the different factor categories of local accountability, promotion, activation, and the development of specific economic activities of different local contexts of sustainability. The research methodology used involves a case study whose complexity necessitated the use of quality and quantity research methods in order to underline specific elements of the rural area in the Romanian mountainous region. Specifically, we used a strategic diagnosis of the Romanian mountainous region using the PESTEL and SWOT models. In order to have relevant strategic options available, the continuity of research was achieved through the use of SOR analysis, creating a problem tree and an objectives tree.

The effects of reaction temperature, reaction time, heating rate, nitrogen flow rate and catalyst quality on the oil yield and oxygen content in the oil were investigated by using the single factor principle. Too high and too low reaction temperature, nitrogen flow rate, heating rate and reaction time have improved the yield of bio-oil, but the oxygen content in bio-oil is higher. The reduction of catalytic dose is beneficial to the increase of oil yield but not conducive to the increase of aromatic compound content. The optimal reaction conditions were observed as reaction temperature of 500℃, nitrogen flow rate of 110 mL/min, heating rate of 20℃/min, reaction time of 15min, mass ratio of catalyst to coconut coat powder was 1, and the oil yield was 4.97%, aquatic yield was 35.80%, and solid yield was 30.78%. The gas yield was 28.45%, the oxygen content was 10.3%, and the aromatic compound content was 89.7%.The analysis of catalytic cracking mechanism shows that most of the oxygen-containing compounds in the bio-oil are generated into water and aromatic compounds by catalytic cracking reaction at high temperature, thus removing oxygen.

Drilling centers are collaborative environments dedicated to facilitate decision-making in the well construction, where multidisciplinary teams work to support operations. The oil operators usually have drilling centers with different types of ergonomic features with considerable potential of integration, creating the opportunity to an Ergonomic Workplace Analysis. This paper aims to present the analysis of infrastructure requirements of one specific company in Brazil. The method was based on a survey with employees, which, coped with a statistical analysis, enabled understanding the impact of the layout requirements. The result is an approach to design collaborative environments, standardizing and defining models for the industry.

With the widespread use of new equipment such as distributed photovoltaics, distributed energy storage, electric vehicles, and distributed wind power, the control of low-voltage distribution networks (LVDNs) has become increasingly complex. Acquiring the most recent topological structure is essential for conducting accurate analysis and real-time control of LVDNs. The signal-injection-based topology identification algorithm is favored for its speed and efficiency. This study proposes a new signal-injection-based topology identification algorithm aimed at solving the issues of reduced completeness and correctness of identification caused by missing feature signal records (FSRs). By analyzing the correlations between FSRs of different positions, the algorithm employs vertical and horizontal completion methods to effectively address missing data, combined with inclusion detection algorithms, to identify the topology of LVDNs. Based on the study of actual LVDN data, the results indicate that the algorithm not only significantly improves the completeness and correctness of topology identification for LVDNs but can also increase the number of devices in operation by evaluating the status of topological equipment, further enhancing the topology identification performance.

The alternating stress caused by periodic high-pressure injection and extraction in gas storage can potentially induce fault slippage, compromising the sealing integrity of faults within these facil-ities. Understanding the mechanical behavior of faults under alternating stress is crucial for en-suring the long-term stability and safety of gas storage operations. To explore the impact of fault dip angle and fault gouge strength on fault slip characteristics, fault samples were prepared with uniaxial compressive strengths of 20.1, 30.2, 42.4, and 51.4 MPa at two distinct dip angles. Triaxial compression experiments were conducted under alternating stress conditions corresponding to operational pressures at a specific gas storage in China. Results indicate that faults with dip angles of 30° and 45° tend to fail at their weakest points. Increasing strength of fault gouge shifts failure mechanisms from interfacial failure between gouge and surrounding rock towards internal gouge failure, often accompanied by shear failure across sections, resulting in characteristic "X"-shaped conjugate shear failures. The decrease in the ratio of bedrock strength to fault gouge strength elucidates the observed phenomena of initial reduction followed by increased fault deformation. Transition points for faults with 30° and 45° dips occur around the strength ratios of 1.7/1 and 1.2/1, respectively. Fault damage exhibits a negative correlation with fault gouge strength and a positive correlation with fault dip angle. Samples with higher strength fault gouge at a 30° dip angle generally incur less damage compared to those with lower strength fault gouge at a 45° dip angle. Moreover, higher maximum static friction coefficients denote greater fault resistance to slipping, with 30° faults consistently demonstrating superior resistance compared to 45° faults. Additionally, higher strength fault gouge consistently enhances slip resistance under identical dip angles.

As the demand for long-distance flights continues to increase, supersonic transport (SST) has once again become a hot research topic. However, due to its uniqueness, there was few corresponding evaluation methods to compare the supersonic civil aircraft with common subsonic aircraft. This paper proposed an evaluation method for the competitiveness of supersonic civil aircraft based on the Analytic Hierarchy Process (AHP). Key indicators were selected to form a competitiveness evaluation model from the perspective of four criterion factors of economy, comfort, adaptability, and environment. The evaluation method proposed in this paper could reflect characteristics of supersonic civil aircraft and other subsonic aircraft, and effectively compare their competitiveness. This work can be used to evaluate the social acceptance of supersonic civil aircraft and provide reliable decision-making support for airlines' design work.

Recent technological advancements in produced water for the oil and gas industry have a long history that spreads over centuries and has roots with many mathematicians, physicists, engineers, and inventors. Working to understand the many ideas and questions has helped to bring the produced water technologies to where we are today. Fluid mechanics is an essential factor in the world of engineering because it comes with significant benefits when designing the necessary equipment to overcome the challenging endeavors of daily operations. Many of us believe certain ideas or products were developed within a specific year not fully understanding the idea or concept might be hundreds of years old. For example, when we think of fluid mechanics, we do not think of Archimedes' immersing King Hiero II crown in water. Archimedes did this to determine the displacement of the water as he knew gold was denser than silver. Archimedes was one of the pioneers who was part of the beginning of fluid mechanics. Another interesting fact is the first valve invented was in 1 AD by Heron of Alexandria. This valve can be described as the very first hydraulic valve. The evolution of technology over hundreds of years has made considerable innovations benefiting engineers all over the world. These innovations come in the form of PLCs, RTUs, PIDs, mathematical formulas, processing methods, and SCADA systems.

Background: The study was conducted to investigate if the mRNA vaccine technology could be adapted for the ectothermic vertebrate Atlantic salmon (Salmo salar). The lipid nanoparticle (LNP) technology has been developed and optimized for mRNA vaccines in mammals, stabilizing mRNA and facilitating delivery into cells. However, its utility at the temperature and specific biological environment in ectotherms remains unclear. In addition, it is unknown if modified mRNA containing non-canonical nucleotides can correctly translate in salmonid cells. Methods: We used an mRNA transcript coding for enhanced green fluorescence protein, flanked by the untranslated regions of the hemagglutinin-esterase gene of infectious salmon anemia virus, and a 120-base-long poly(A) tail. The mRNA was generated by in vitro transcription where uridine residues were replaced with N1-methyl-pseudouridines, and then encapsulated in LNPs. Results: When transfected into the salmonid cell line CHH-1, the mRNA-LNP construct induced expression of EGFP. Furthermore, when mRNA-LNPs were injected intramuscularly into salmon, in vivo protein expression was demonstrated by immunohistochemistry. EGFP was observed in cells infiltrating the space between the muscle cells in a focal inflammatory response. Conclusion: The results indicate that the N1-methyl-pseudouridine modified mRNA encapsulated in LNPs can be used to express antigens of interest in salmonid fish.

The opportunities and advantages of implementing Artificial Intelligence (AI) and Machine Learning (ML) to optimize the process control of wastewater treatment in the Oil and Gas industry are discussed in this work. Discussion is centered around five major points: 1) Various types of Oil and Gas wastewater (Sour, Oily, Produced) and industry standards/methods for treatment, including specific case studies and challenges when treating certain wastewater. This section aims at the common types of wastewater in the Oil and Gas industry and how they are generally treated. 2) How AI/ML has been implemented in wastewater treatment in various industries; summary of which AI/ML languages were used along with a brief overview of how they work. This article focused on an understanding of the specific case studies and AI explanations to understand the effectiveness of wastewater treatment using AI/ML. 3) AI that is currently implemented in Oil and Gas such as personal protective equipment (PPE), smartwatches radiofrequency identification etc. This showed that AI/ML already plays a successful role in the Oil and Gas industry and has proven to help optimize many processes and components. Many of these AI/ML implementations are now industry standards and have greatly benefitted the industry. This section demonstrates that the implementation and the use of AI/ML have been proven to be a successful endeavor and that expanding the role of AI/ML would be beneficial. 5) Using the established points from the previous sections the paper outlines why AI/ML is ideal for Oil and Gas wastewater treatment; this argument centers around fit-for-purpose treatment, and the possible uses of the treated water. A determination of the best-suited AI languages, possible implementation scenarios, and how this would shift the way Oil and Gas industries treat and approach wastewater is presented to the reader.

Keywords: Linear differential arrays; beam steering; frequency-invariant beamforming.

Volatile organic compounds (VOCs) released from plants have been correlated with disease-status. Analysis of VOCs using GC-MS is time-consuming, laboratory-based, and requires specialist training. Electronic nose devices (E-nose) provide a portable alternative. Three different E-nose devices were compared to assess how accurately they could detect Mango Twig Tip Dieback and Panama disease in banana. The devices were initially trained on known volatiles, then pure cultures of Pantoea sp., Staphylococcus sp., and Fusarium odoratissimum, and finally, on infected and healthy mango leaves and field-collected, infected banana pseudo-stems. The experiments were repeated three times with six replicates for each host-pathogen pair. The variation between healthy and infected host materials was evaluated by principal component and linear discriminant analysis, cross-validation and chemometric data analysis. GC-MS analysis was conducted contemporaneously and identified an 80% similarity between healthy and infected plant material. The portable C 320 was 100% successful in discriminating known volatiles but had a low capability in differentiating healthy and infected plant substrates. The advanced devices (PEN 3 / MSEM 160) successfully detected healthy and diseased samples with a high variance. The results suggest that E-nose devices are more sensitive and accurate in detecting changes of VOCs between healthy and infected plants compared to headspace GC-MS.

The multi-stage, multi-level assembly job shop scheduling problem (MsMlAJSP) is commonly encountered in the manufacturing of complex customized products. Ensuring production efficiency while effectively improving energy utilization is a key focus in the industry. For the energy-efficient MsMlAJSP (EEMsMlAJSP), an improved imperialist competitive algorithm based on Q-learning (IICA-QL) is proposed to minimize the maximum completion time and total energy consumption. In IICA-QL, a decoding strategy with energy-efficient triggers based on problem characteristics is designed to ensure solution quality while effectively enhancing search efficiency. Additionally, an assimilation operation with operator parameter self-adaptation based on Q-learning is devised to overcome the challenge of balancing exploration and exploitation with fixed parameters, thus the convergence and diversity of the algorithmic search is enhanced. Finally, the effectiveness of the energy-efficient strategy decoding trigger mechanism and the operator parameter self-adaptation operation based on Q-learning is demonstrated through experimental results, and the effectiveness of IICA-QL for solving EEMsMlAJSP is verified by comparing with other algorithms.

Geological storage of carbon dioxide (CO2) is a crucial technology for mitigating global temperature rise. Near-depleted edge-bottom water reservoirs are attractive targets for CO2 storage, as they can not only enhance oil recovery (EOR) but also provide important potential candidates for geological storage. This study investigated CO2 enhanced oil recovery and storage for a typical near-depleted edge-bottom water reservoir that had been developed for a long time with a recovery factor of 51.93%. To improve the oil recovery and CO2 storage, new production scenarios are explored. At the near-depleted stage, by comparing the four different scenarios of water injection, gas injection, water alternating gas injection, and bi-directional injection, the highest additional recovery of 8.64% is achieved by the bi-directional injection scenario. Increasing the injection pressure leads to a higher gas-oil ratio and liquid production rate. After shifting from the near-depleted to depleted stage, the most effective approach to improve CO2 storage capacity is to increase reservoir pressure. At 1.4 times the initial reservoir pressure, the maximum storage capacity is 6.52×108 m3. However, excessive pressures boosting poses potential storage and leakage risks. Therefore, lower injection rates and longer intermittent injections are expected to achieve a larger amount of long-term CO2 storage. Through the numerical simulation study, a gas injection rate of 80,000 m3/day and a schedule of 4-6 years injection with 1 year shut-in was shown to be effective for the case considered. During 31 years of CO2 injection, the percentage dissolved CO2 increased from 5.46% to 6.23% during the near-depleted period, and to 7.76% during the depleted period. This study acts as a guide for the CO2 geological storage of typical near-depleted edge-bottom water reservoirs.

The escalating concerns over climate change have propelled industries worldwide to seek innovative strategies for mitigating greenhouse gas emissions. Within the energy sector, Carbon Capture and Storage (CCS) technology emerges as a promising solution to curtail emissions and foster sustainable development aims for net zero approach. The research delves into the role of government support in expediting CCS adoption for the maximum potential of 9.79 MtCO2 storage from six major refinery plants. The refineries mentioned above are anticipated to necessitate an initial capital investment of approximately 18,307 million THB. This research focuses on potential business model proposals appropriate for a country's context, specifically applying CCS technology to Thai oil refining sector. To achieve the realization of CCS within the context of this study, a combination of three essential measures will be required: tax incentives, carbon credits, and grants. This process will commence with the implementation of tax incentives, followed by an increase in the carbon price within the country. Finally, the establishment of a dedicated fund, funded through deductions from oil excise tax revenue, will play a pivotal role in facilitating the necessary financial support for the emergence of CCS.

The normal growth and development of skeletal muscle is essential for the health of the body. The regulation of skeletal muscle by intestinal microorganisms and their metabolites has been continuously revealed. Acetate is the predominant short-chain fatty acid synthesized by gut microbiota through the fermentation of dietary fiber, however, the underlying molecular mechanisms governing the interaction between acetate and skeletal muscle during rapid growth stage remain to be further elucidated; Here, specific pathogen-free (SPF) mice, germ-free (GF) mice, and germ-free mice supplemented with sodium acetate (GS) were used to evaluate the effects of acetate on skeletal muscle growth and development of young mice with gut microbiota deficiency; We found the concentration of serum acetate, body mass gain, succinate dehydrogenase activity and expression of myogenesis maker gene of skeletal muscle in the GS group was higher than GF group following sodium acetate supplement. Furthermore, the transcriptome analysis revealed that acetate activated biological processes regulating skeletal muscle growth and development in GF group that are inhibited due to gut microbiota deficiency. In vitro experiment, we proved that acetate up-regulated Gm16062 to promote skeletal muscle cell differentiation; Overall, our findings proved that acetate promote skeletal muscle growth and development in young mice via increase Gm16062 expression.

‘‘Sustainable Supply Chain Management’’ (SSCM) has become a hot topic on which eminent researchers are working on every day. However, it is clear that we still observe in this field of research, an artistic vagueness on the fundamental differences between Sustainable Supply Chain Management and Green Supply Chain Management (GSCM) Moreover, it is regrettable to note that previous researchers haven't yet thought about having a specific theory which can be applied to SSCM, the use of macro theories still being observed. In addition, we observe a lack of research in the oil and gas industry especially in Developing Countries when we know that this industry is the most lucrative and polluting. Therefore, this paper’s purpose consists to make a Systematic Literature Review (SLR) of 38 papers published from 2005 to 2023 especially in oil and gas industry and in Developing Countries, in order to make a clear distinction between SSCM and GSCM while highlighting the practices related to them and at the same time, generating a united theory which will bring together the triple bottom line of the SSCM. As findings, the authors built a Conceptual Framework that applies the triple bottom line of the SSCM in oil and gas industry by demonstrating that GSCM which is more related to environmental issues and is a part of the SSCM. Therefore, in order to be more efficient and to have a great impact on their performances, Oil and gas companies should apply SSCM practices rather than GSCM practices which are very different from what is applied in Developed Countries because of certain barriers and pressures.

In order to achieve the dual carbon goal and simplify the decarbonization process, a CO2 recovery process of the fire-flooding exhaust was designed. The process adopted the two-stage membrane separation method to recover CO2 and obtain high purity CO2 rich flow, and then through the mixed refrigerant liquefaction and rectification column, food grade liquid CO2 was obtained. HYSYS process simulation shows that for the fire-flooding exhaust with a flow rate of 1000 kg/h and a given composition, the process can achieve a CO2 recovery of 69.02%, total product sales S=2086.8 yuan/h, and specific power consumption of 2.818 kW∙h/kg. On this basis, a hybrid simulation platform of HYSYS & Matlab was established. Taking the specific power consumption of the product as the objective function, sequential quadratic programming (SQP) algorithm was adopted to optimize the process, and the optimized specific power consumption was reduced by 18.8%. Finally, by adjusting N2/CO2 components, the adaptability of the optimization condition was analyzed.

As waterflooding multi-layer reservoirs get into the high-water-cut stage, inter-layer conflicts become increasingly serious, leading to a worsening development effect over time. Production layers regroup is an effective approach for resolving inter-layer conflicts and improving waterflooding efficiency. At the current stage, there are limitations for most of the methods of production layers regroup. This article proposes a smart method for optimizing the layer regroup plan based on genetic algorithm. Comprehensively considering various factors that affect the regroup of layers, based on the combination principle of "smaller intra-group variance and larger inter-group variance of each influencing factor are expected ", genetic algorithm is used to calculate the fitness value of the initial combination schemes, the advantageous schemes with higher fitness values are selected as the basis of the next generation. Then crossover and mutation operations are performed to those advantageous schemes to generate new schemes. Through continuous selection and evolution, until the global optimal solution with the highest fitness value is found, the optimal combination scheme is determined. Comparative analysis with numerical simulation results demonstrates the reliability of this intelligent method, with an increased oil recovery of 4.34% for the sample reservoir. Unlike selecting a preferable plan from a limited number of predefined combination schemes, this method is an automatic optimization to solve the optimal solution of the problem. It improves both efficiency and accuracy as compared to conventional reservoir engineering methods, numerical simulation methods and most of the mathematical methods, thus could provide effective guidance for EOR strategies of waterflooding reservoirs in high-water-cut stage.

Palm oil production involves unit operations that lead to greenhouse gas emissions. A typical mill is estimated to produce greenhouse gas emissions of 637–1,131 kg CO2 eq/t crude palm oil. There has been a huge effort to reduce the carbon footprint of palm oil mills. However, the data from such research have not been consolidated. This paper reviews significant information, results, and conclusions derived from studies in the literature. The latest developments in palm oil milling operations and information on greenhouse gas emissions are presented. Current initiatives in reducing carbon footprint of palm oil mills are discussed along with an assessment of the technologies employed. These include the conventional method of capturing biogas from palm oil mill effluent and emerging approaches such as converting palm sludge oil into biodiesel, deploying enzyme-assisted oil extraction, and converting biomass into fuel for energy generation as an alternative to coal and other fossil fuels. The importance of self-sufficiency is deliberated because a self-sufficient palm oil mill is estimated to reduce emissions by 457 kg CO2 eq/t crude palm oil compared to a mill that requires an external power supply. Methods with the greatest positive effect on the carbon footprint are identified for further investigation.

In this study, we analyzed the microbial community of traditional fermented foods in Jeju Island to identify the distribution of useful microorganisms and confirm their anti-inflammatory and anti-melanogenic effects to determine their potential use as cosmetic ingredients. Firstly, we examined the microbial communities of Omphalius rusticus Jeotgal (OR), Spratelloides gracilis Jeotgal (SG), Chromis notata Jeotgal (CN), Turbo cornutus Jeotgal (TC), Trichiurus lepturus intestine Jeotgal (TL), Branchiostegus japonicus Sweet Rice Punch (BJ), Salted Anchovy Sauce (SA), Jeju Soy Sauce (JSS), and Jeju Soybean Paste (JSP). We found that Latilactobacillus sakei (87.2%), Tetragenococcus halophilus (37.7%), T. halophilus (96.8%), Bacillus subtilis (23.4%), T. halophilus (71.3%), L. sakei (53.7%), Lentibacillus sp. (42.9%), Enterococcus durans (14.6%), and E. durans (32.8%) were the dominant species. Secondly, to study the nine Jeju fermented foods’ anti-inflammatory and anti-melanogenic effects, we employed RAW 264.7 and B16F10 cells, classic cell models for inflammation and melanogenesis studies. Ethyl acetate extracts of the nine Jeju fermented foods all inhibited nitric oxide (NO) and melanin production in a concentration-dependent manner. Thirdly, to test the applicability of the nine Jeju fermented foods to human skin, we used the MTT assay to assess their cytotoxic effects on human keratinocytes (HaCaT cells). Finally, the topical applicability of the nine Jeju fermented foods was tested through primary skin irritation, and it was found that they did not cause any adverse effects. Therefore, extracts from the nine Jeju fermented foods have potential applications as ingredients in anti-inflammatory and anti-melanogenic products and can be used in the cosmetic industry.

This research was conducted with the aim of knowing how to compare the financial performance of the oil and gas trading industry with cross-sectional analysis techniques. The type of research conducted in this research is qualitative research with research objects at several companies, namely PT Radiant Utama Interinsco Tbk, PT Elnusa Tbk, PT AKR Corporindo Tbk, and PT Aneka Gas Industri Tbk. The data used in this study comes from secondary data, namely the internet in the form of company financial reports for the 2019-2021 period obtained from the Indonesia Stock Exchange. The results of this study indicate that PT Radiant Utama Interinsco Tbk has the best financial performance on inventory turnover ratio and average age, PT Elnusa Tbk has good inventory performance on current ratio, quick ratio, DAR, and DER., PT AKR. Corporindo Tbk has performed well on the ratios of TIE, FCC, Dividend Payout, Dividend Yield, and PER. PT Aneka Gas Industri Tbk has performed well on the ratio of Receivables Turnover Ratio and Average Age of Receivables.

The Shimensi super-large tungsten polymetallic deposit is located in Late Jurassic- Early Cretaceous Porphyry-Skarn tungsten ore belt in the south Yangtze metallogenic belt. There are 3 types of mineralization: veinlet-disseminated type, thick quartze vein type and hydrothermal crypto-explosive breccia type. Based on geological studies, this paper presents new petrographic, microthermometric, laser Raman spectroscopic and hydrogen and oxygen isotope research of the fluid inclusions from the deposit. The results show that there are five different types of fluid inclusions: liquid-rich inclusions, vapor-rich inclusions, pure liquid inclusions, pure vapor inclusions, and fluid inclusions containing a solid crystal. The homogenization temperatures of the fluid inclusion range from 140℃-270℃, the salinities are 3%-5% NaCleq and the densities of ore-forming fluid range from 0.64 g/cm3 to 0.99 g/cm3. For the analyses of Laser Raman spectroscopic, the ore-forming fluids can be approximated by a Ca2+-Na+-SO42--Cl- fluid system with small amount of CO2, CH4 and N2. Otherwise, the datas of the pressure, pH and Eh show a fluid metallogenic environment of low pressure, weak acid and weak reduction. The values of the homogenization temperature in 3 types of orebodies suggest that the mineralization is characterized by the decrease of the temperature under the condition of the fluid immiscibility. The H-O isotope values are interpreted to indicate that the ore-forming fluids are mainly composed of magmatic water, and also the meteoric water was added with the process of the magma rising.

In order to establish the formation patterns of the Co–Mg oxide system, samples with different Co:Mg ratios and heat treatment temperatures were synthesized and studied. Study of the sam-ples confirmed the phase transition of MgxCo2–xO4 spinels into corresponding solid solutions at 800–900 °C. The similarity of formation patterns for different compositions is shown. The rock-salt oxide in low-temperature samples is an anion-modified paracrystalline phase that forms a “true” solid solution only upon spinel decomposition. TPR profiles of decomposed Co3O4 spinel show surface Co3O4 peaks and a wide peak corresponding to well-crystallized CoO, while par-tial Co3O4 TPR up to 380 °C results in dispersed and amorphous CoO. High-temperature non-stoichiometric samples are poorly reduced, indicating their low oxygen reactivity. Spinel reoxidation after heat treatment to 1100 °C by calcination at 750 °C showed complete regenera-tion for MgCo2O4–Co3O4 samples and its absence in case of an excess of MgO relative to stoi-chiometry. Based on the data obtained, it can be concluded that the processes governing the formation of Co–Mg oxide systems are determined by both Co:Mg ratio and the heat treatment conditions, potentially providing the possibility of fine tuning for specific catalytic processes.

The stinging nettle caterpillar, Darna pallivitta (Lepidoptera: Limacodidae) is a serious invasive pest of agricultural products and a health hazard on the Hawaiian Islands first discovered in 2001. Nursery workers and homeowners have been stung by the caterpillars while handling their plants, especially rhapis palms (Rhapis sp.). Throughout its invaded range, it causes widespread damage including the many cultivated and native palm species grown in Hawaii. Of medical importance are the stinging spines of the larva, which cause dermatitis on contact with the skin. Horticulture and nursery products impacted by the limacodid pest are estimated at $84.3 million (2018 value). An eradication attempt with pesticides and lure traps was made but proved unsuccessful and the moth population continued to spread to major Hawaiian Islands (Hawaii, Kauai, Maui, Oahu). The introduction of specific biological control agents from the native region was thought to be the long-term solution for this invasive pest. Initial exploration in Indonesia and Thailand resulted in the introduction of a pupal ectoparasitoid, Nesolynx sp. (Hymenoptera: Eulophidae: Tetrastichinae), that was not specific. The oriental wasp, Aroplectrus dimerus Lin (Hymenoptera: Eulophidae: Eulophinae), idiobiont gregarious ectoparasitoid of the stinging nettle caterpillar, was introduced from Taiwan in 2004 for host specificity studies and biocontrol in Hawaii. Host range testing showed the parasitoid attacked only limacodid species and it was approved for field release in 2010. The parasitoid identity, host specificity under containment facility conditions, reproductive performance, colonization on the major infested sites were assessed. A total of 13379 parasitoids were colonized on162 release sites on four Hawaiian Islands. Evaluations were conducted using field surveys of larvae, pupal counts, and male lure traps. Field parasitism was thoroughly investigated on Oahu Island averaging 18.9 ± 5.6 % of 3923 collected larvae during 2010 – 2023. The numbers of male moths caught/trap/month were significantly reduced on Oahu Island (P

Indonesia has emerged as one of the leading producers and exporters of palm oil, as supported by data from the Central Bureau of Statistics in 2021, which indicate that Indonesian palm oil exports reached an impressive value of US$ 18.44 billion, or IDR 258 trillion, in 2020, marking an 18.43 percent growth compared to the previous year. Furthermore, the domestic market for palm oil and palm kernel oil remains substantial, despite improvements in export quantities. Various industries, including cooking oil refineries, specialty fats, shortening, margarine, bath soaps, and oleochemicals, present potential markets for palm oil (CPO) and palm kernel oil (PKO). The palm oil industry encompasses four related sub-sectors, namely growers, millers, refiners, and oleochemicals, forming an integrated value chain from upstream to downstream. The current focus on environmental, economic, and social sustainability is driving companies to adopt internal green activities and expand their efforts into sustainability supply chain management (SSCM). Implementing SSCM practices is often seen as economically beneficial, as research has demonstrated their positive impact on firm performance from a resource perspective. Within the palm oil industry, a wide range of green management applications are being utilized. This study aims to examine and highlight the existing sustainable management practices across the entire palm oil supply chain, with a particular emphasis on producing high-quality palm oil. To achieve this objective, the paper utilizes a systematic review methodology, The number of papers analyzed were 62 articles published which involves an extensive review of relevant literature to identify research trends, gaps, and issues. The study seeks to contribute to the body of knowledge by expanding the theory of organizational readiness in preparing globally competitive palm oil products. The research findings hold practical significance for practitioners and academics, providing a comprehensive roadmap for implementing green management applications at the organizational level in the palm oil industry's upstream-to-downstream chain.

sustainability reporting, critical paradigm, upstream oil, and gasThe operating activities of the upstream oil and gas industry directly impact the environment. This industry faces significant social challenges and directly impacts the environment. Many Reputable international sustainability institutions organize sustainability awards. However, community conditions do not have a positive impact on sustainability practices. There are vari-ous serious violations related to sustainability, environmental pollution, multiple cases of cor-ruption, human rights, and other violations. In contrast, the companies receiving this award also received inspection findings of violations committed by The Audit Board of the Republic of In-donesia. This study uses critical discourse analysis that begins with phenomena related to viola-tions of sustainability reporting from scientific journals and other references using a systematic literature review approach over the last ten years. It produces a critical paradigm that is not val-ue-free, which is the basis for framing thought utilizing the theory of hegemony. The results of this study indicate that the upstream oil and gas industries are obliged to implement Corporate Social Responsibility (CSR) practices and Sustainability Reports (SR), has biased factors that are contrary to the sustainability concept and are not under the sustainability award based on evi-dence obtained from the stages of manuscript analysis with systematic literature review

This paper analyzes the relationship between corporate social responsibility (CSR) and social impact within the oil industry in an emerging market (Peru). Following the emerging literature on the social impact field, and using the case study methodology, the findings show that the expected positive relationship is diverse depending on several factors. Specifically, the results reveal that companies must focus on community and environmental responsibility, together with stakeholders' involvement to achieve social impact. However, when companies are weak in any of the previous factors, then the social impact is only partially accepted or even withdrawn.

Analyses of the three predominant types of sedimentation – clastic, carbonate and black shale – revealed their discontinuity/continuity in different facies environments of the Middle and Late Devonian of the central part of the Volga-Urals petroleum province, namely (1) in depressions, both condensed and non-condensed, (2) on the slopes of depressions and (3) in shallow water environments represented by tectonic arches or localised biohermal uplifts. The regional zonation of conodonts, correlated with the global chronostratigraphic scheme, substantiates the stratigraphic completeness of the general Devonian sequence in this area. In particular, the sedimentation of organic-rich black shales, traditionally considered as source rocks, lasted more than 29 million years, starting from the Late Eifel and ending at the Devonian-Carboniferous boundary. There was only one hiatus in the deposition of both black shales and carbonate sediments, lasting about 2.5 million years at the end of the Frasnian. That interval is dominated by clastic sediments, which are considered to be the most productive reservoirs of the Volga-Ural province. In the time interval from the beginning of the Eifel to the end of the Frasnian (about 17 Ma), (a) clastic sediments show the highest accumulation rates; (b) the most complete sequences occur in depressions; and (c) arches and uplifts show the most significant gaps in the geological record. During Famennian, (a) clastic sedimentation has completely ceased; (b) differences between the slopes of troughs and shallow-water environments have diminished, resulting in stable accumulation of carbonate sediments in both settings; (c) the decrease in sequence thickness (up to 50 m) in depressions suggests reduced accumulation rates of deep-water organic-rich black shales. The results help to understand the complex spatial relationship between different coexisting sedimentation types and focus attention to the incompleteness of the geological record in different environments.

High-precision conical threads are widely used in responsible joints in the drilling of oil and gas wells. Difficult underground drilling conditions due to the occurrence of significant mechanical loads and an aggressive environment in wells require the use of workable materials that are often difficult to machine. The huge need for such connections dictates the use of high-performance cutting tools, which means that high demands are placed on their effective geometric performance. The study describes the theoretical dependence of the profile precision of the tapered drill-string tool-joint threads of all standard sizes on the complex of a cutting tool geometric parameters and cutting tool setting accuracy. The experiments include an assessment of the geometric accuracy of the profile of the obtained NC23 thread connector, depending on the values of the installation angles and the declared tangential displacement of the standard threaded carbide insert.

The digital transformation in Industry 4.0 has revolutionized quality control paradigms, integrating advanced technologies such as augmented reality, deep learning, and computer vision systems into a new era called "Quality 4.0". This study systematically reviews how these technologies are shaping new practices in continuous quality supervision and improvement, adapting to increasingly automated and connected production environments. Through a comprehensive analysis of the literature, practical applications in various industrial sectors, from manufacturing and agriculture to the production of sweets and snacks, are highlighted. Additionally, the conceptual and detailed design of a quality control system using artificial intelligence tools is presented, focusing on the inspection of dimensions, color, weight, and labeling of MDF boxes. The proposed system demonstrates an effective integration of sensors, high-definition cameras, and deep learning algorithms, validated through tests with boxes of different sizes. The results suggest that the adoption of these technologies not only improves the accuracy and efficiency of inspections but is also essential to maintaining high-quality standards in a dynamic and competitive industrial environment.

Antioxidant, anti-inflammatory and chemo-preventive features have been reported for the carotenoid diatoxanthin. Diatoxanthin is only produced by a few groups of microalgae where it functions in photoprotection. Its large-scale production in microalgae is currently not feasible. In fact, rapid conversion into the inactive pigment diadinoxanthin is triggered when the cells are removed from the high-intensity light source, which will be the case during large-scale harvesting of microalgae biomass. Zeaxanthin epoxidase (ZEP) 2 and/or ZEP3 have been suggested to be responsible for the back-conversion of high-light accumulated diatoxanthin to diadinoxanthin in low light in diatoms. Using the CRISPR/Cas9 gene editing technology we knocked out the ZEP2 and ZEP3 genes in the already commercially used marine diatom Phaeodactylum tricornutum to investigate their role in the diadinoxanthin-diatoxanthin cycle, and to determine if one of the mutant strains could function as a diatoxanthin production line. Light shift experiments proved that ZEP3 encodes the enzyme converting diatoxanthin to diadinoxanthin in low light. Loss of ZEP3 caused the high-light accumulated diatoxanthin to be stable for several hours after the cultures had been returned to low light, suggesting that zep3 mutant strains could be suitable as commercial production lines of diatoxanthin.

Soluble inorganic pyrophosphatase (sPPase), a pyrophosphate hydrolase, has been shown to play an important role in several physiological processes such as plant growth and development, metabolic activities, and response to abiotic stresses, but sPPase has been less studied in woody plants. In order to preliminarily verify whether the soluble inorganic pyrophosphatase in Eucommia ulmoides Oliver (E. ulmoides) has a role in resistance to drought stress, we amplified the EuSIP5 (E. ulmoides soluble inorganic pyrophosphatase 5) cDNA sequence from E. ulmoides by RT-PCR. In order to study the drought resistance of the Eucommia ulmoides soluble inorganic pyrophosphatase 5 (EuSIP5) gene, the cDNA sequence of the EuSIP5 gene was amplified from Eucommia ulmoides Oliver by RT-PCR. Bioinformatic analysis indicated that EuSIP5 might be an unstable amphipathic protein, mainly located in the cytoplasm. E. ulmoides, the highest expression of the EuSIP5 gene was found in male leaves and pericarp from April to October, and in leaves of E. ulmoides in July and September. During drought, the expression of EuSIP5 in seedling E. ulmoides leaves was significantly higher than that of the control. An overexpression vector harboring the EuSIP5 was constructed and introduced into the tobacco (Nicotiana tabacum cv. Xanthi). We found that during drought stress, the appearance of wilting was delayed by 4 days in transgenic tobacco plants (OE) compared with wild type plants (WT), and the expression of drought-related genes DET2, CYP85A1, P5CS, ERF1 and F-box was found to be increased in transgenic tobacco leaves, as well as the enzyme activities of the protective enzymes: peroxidase (POD), superoxide dismutase (SOD) and catalase (CAT) were significantly higher than those of the WT, and the malondialdehyde (MDA) content was lower than the WT. These results indicated that the introduction of EuSIP5 gene into tobacco increased the expression of drought-related genes, enhanced the anti-membrane oxidation ability of tobacco, and reduced the oxidative stress damage, thus improving the drought resistance of tobacco.

In order to foster a more sustainable and eco-friendly trajectory for the construction industry, while concurrently mitigating environmental pollution and energy inefficiency, it is imperative to cultivate an environmentally conscious building and urban environment. Under the background of carbon peak and carbon neutrality, green building evaluation system (GBRS) has become a research hotspot in the field of green building. This paper systematically summarizes the current research progress based on GBRS, focuses on the current weight and indicators setting, analyzes it with Cite Space software, and puts forward its future development direction. The results show that the weight setting method of green building evaluation system is determined by multidimensional and multi-method. From the perspective of environment, society and economy, the scope of indicators setting is expanding. The green building evaluation system will play a guiding role in green building design, and the evaluation process will continue to be optimized and developed in the direction of intelligence and automation.

In order to develop novel botanical insecticides, the joint action of Ligusticum chuanxiong oil (LCO) and lemongrass oil (LO) against Aphis citricola van der Goot was determined systematically indoors and outdoors. The chemical profiles of LCO and LO as determined by gas chromatography- mass spectrometry analysis revealed that main compounds from LCO were Z-Ligustilide (44.58%) and Senkyunolide A (26.92%), and that of LO were geranial (42.16%) and neral (32.58%), respectively. The mixture of LCO and LO showed significant synergy against A. citricola, with a common-toxicity coefficient (CTC) value of 221.46 at the optimal ratio of LCO to LO (4: 1, w/w). Based on the results of solvents and emulsifiers screening, L. Chuanxiong oil · Lemongrass oil 20% emulsifiable concentrate (20% LCO · LO EC) was developed, which was confirmed to meet the requirements of a commercial pesticide by quality test. Field trials indicated that the insecticidal activity of the diluted 20% LCO · LO EC (1000 fold dilution) was comparable to conventional pesticide (20% imidacloprid EC) on A. citricola 7 days after application. Thus, the mixture of LCO and LO has the potential to be further developed as a botanical pesticide.

Density is a crucial parameter for quantitatively describing the physical properties of liquids. It serves as an important indicator for scientific research, production process control, pipeline transportation, and other aspects. In oil pipeline transportation and raw material processing, real-time online measurement of liquid density is of great significance. This paper analyzes the working principle of an on-line vibrating tube densitometer and derives the fitting equation for temperature, pressure, and density；it also conducts experiments with an on-line vibrating tube liquid densitometer and establishes a traceability chain for the experimental device. The experimental setup includes a desktop densitometer system, a multi-temperature field constant temperature stirring system, a walk-in constant temperature box, an automatic blowing system, and a frequency acquisition and calculation system. The uncertainty of the device's evaluation is U= 0.08kg/m3, k=2.The experimental research on the on-line vibrating tube liquid densitometer can be carried out within the range of (650~1400) kg/m3, (10~70)℃, (0~50)bar the metrological performance of the vibrating tube densitometer can be researched by utilizing the straight tube type and the elbow type on-line vibrating tube densitometer. A preliminary study was conducted on the effects of different densities, temperatures, and pressures on the vibrating tube system's vibration cycle. The fit coefficient and error were calculated, and the experimental results were compared to the theoretical analysis to confirm the device's conformity. The study verified the device's scientific and reasonable design, and demonstrated that it is feasible to use the device for follow-up research.

In the dynamic landscape of the telecommunications industry, understanding and mitigating customer churn is paramount for maintaining competitive advantage and sustaining revenue streams. This comprehensive literature review delves into the intricacies of customer churn prediction, a crucial aspect in fortifying the bond between telecom businesses and their customers. The review methodically analyzes 11 articles published between 2000 and March 2024, spotlighting the strategic role of Customer Relationship Management and the prevalence of high churn rates that necessitate a shift from customer acquisition to retention strategies. Furthermore, the review navigates through the challenges inherent in churn prediction, including the complexities of managing large, imbalanced, and noisy datasets and the intricacies involved in model selection and optimization. Despite these challenges, the paper highlights the superior capability of machine learning techniques in handling complex datasets to provide accurate predictions, albeit acknowledging their practical complexities. The main aim of the study is to provide an overview, serving as a knowledge base for researchers interested in machine learning techniques within the realm of telecommunications.

Brand trust holds significant importance in the Mongolian cashmere industry. This study examines the primary predictors of customer brand trust among Mongolian cashmere users. Our research includes a survey with 800 participants and 20 individual interviews conducted among both Mongolian cashmere users and non-users. We utilized an online platform to reach participants, employing convenience sampling. The study investigates the relationship between various factors and brand trust within the context of Mongolian cashmere brands. Through a combination of in-dividual interviews and statistical analysis, we test six hypotheses. The findings indicate that higher brand quality, a strong reputation, greater transparency, effective issue resolution, commitment to environmental and social responsibility, and pre-purchase research on such commitments positively impact brand trust. Key insights gleaned from the interviews emphasize the importance of quality, reputation, transparency, customer service, and environmental responsibility in shaping consumer trust. These results offer valuable implications for cashmere brands aiming to bolster consumer trust and foster loyalty.

The study aimed to compare the cardiovascular benefits of Omega-3 Polyunsaturated Fatty Acids from fish oil versus krill oil in different forms and dosages. Following PRISMA 2015, data analysis with R software, and databases were searched from 1993 to 2023, (ID PROSPERO: CRD42024502338). Sixty high-quality studies were analyzed, covering various forms of fish oil and krill oil at different dosages (fish oil (ethyl ester-EE, triglyceride-TG, re-esterified triglycerides-rTG, capsules, emulsion-EM); krill oil (phospholipid/free fatty acid-PL/FFA, high concentration phospholipid-HPL, low concentration phospholipid-LPL)). Meta-analysis revealed that krill oil with phospholipid/free fatty acid at doses 2000-2900 mg effectively lowered triglycerides, while fish oil in ethyl ester form at doses above 3000 mg significantly reduced total cholesterol. Fish oil in triglyceride form at doses 2000-2900 mg and other variations positively impacted HDL-C levels. Fish oil in EE form above 3000 mg and triglyceride form below 2000 mg notably reduced LDL-C. However, there was limited effectiveness observed for other interventions. Analysis for LDL-C exhibited publication bias, while other parameters demonstrated reliability (Egger's test). In conclusion, krill oil - PL/FFA, Fish oil - EE above 3000 mg, Fish oil - TG 2000-3000 mg, and fish oil - rTAG 300-1900 mg effectively in reducing heart risk patients.

This paper examines the use of business maturity models as a tool for achieving business maturity and improving organizational performance in a rapidly changing business environment. Specifi-cally, the paper evaluates existing maturity models and methodologies, analyzes their effective-ness, and develops a novel and enhanced model tailored to the oil and gas sector. The authors highlight the importance of considering fundamental factors that underlie the implementation of maturity models and the need to evaluate their fit with organizational goals and values. The pa-per concludes by emphasizing the ongoing nature of business maturity and the effectiveness of theproposed Business Maturity Framework (BMF) model in enhancing operational excellence, competitiveness, and sustainable growth in the oil and gas industry. The paper makes a notable contribution to the specialized literature precisely through the differ-ent approaches to the business maturity process and through the proposed business maturity model itself as a base of strategy formulation, which includes a new dimension. This dimension analyzes whether the market and customers are ready for the level of digitization that the com-pany wants to achieve in a future state.

The ubiquitous presence of microplastics (MPs) in the environment poses a threat to ecosystems and increases concerns about their exposure to the human body. However, despite being consumed for health improvement, limited research has been conducted on MPs in functional foods. This study aimed to investigate the occurrence of MPs and the relation of the source of raw material or the manufacture in various omega-3 oil in the Korean market. MPs in omega-3 capsule and raw oil, sourced from both plant-based (PB) and animal-based (AB) sources, were investigated. We developed the method by direct filtration with acetone washing and analyzed MPs greater than 5 μm using microscope-Raman spectroscopy. The average number of MPs was found to be 1.2 ± 1.7 MPs/g for PB raw oil, 2.2 ± 1.7 MPs/g for AB raw oil, 3.5 ± 3.9 MPs/g for PB capsule oil, and 10.6 ± 8.9 MPs/g for AB capsule oil. Polypropylene and polyethylene terephthalate were major specious (83-95 %) found in omega-3 oil. The ratio of size range remained consistent across all groups, with a trend of higher detection rates as the size diminished. The results reveal that the main reason of MPs contamination is not the source of raw material but the manufacturing and packaging process for omega-3 oil.

Since the discovery of the phenomenon of surface-enhanced Raman scattering (SERS), it has gradually become an important tool for the analysis of material compositions and structures. The applications of SERS have been expanded from the fields of environmental and materials science to biomedicine, due to the extremely high sensitivity and non-destructiveness of SERS-based analytical technology that even allows single molecule detection. This article provides a comprehensive overview of Surface-Enhanced Raman Scattering (SERS) phenomenon. The content is divided into several main sections: basic principles and the significance of Raman spectroscopy; historical advancements and technological progress in SERS, as well as various practical applications across different fields. We also discussed how electromagnetic fields contribute to the SERS effect, the role of chemical interactions in enhancing Raman signals, modeling and computational approaches to understand and predict SERS effects.

Self-sustained learning (SSL) is considered a crucial factor in promoting students’ long-term learning and development in a sustainable society. To deepen the understanding of SSL, especially in the context of learning English as a second language, the current study examined the influence of intercultural communicative skills, language mindset, and positive L2 self on SSL in English learning among 1,238 college students in China. The results showed that students not only had a strong language mindset, positive L2 self, and intercultural communicative skills but also scored higher in long-term self-sustained English learning. Findings from the Structural Equation Modeling indicated that both language mindset and intercultural communicative skills positively predicted positive L2 self and self-sustained English learning. Furthermore, language mindset and intercultural communicative skills had an indirect impact on self-sustained English learning through positive L2 self. These findings suggest that to promote English learners’ SSL, instructors should help facilitate students’ intercultural communicative skills and foster a growth language mindset, as well as positive language learning beliefs.

In this study, the microbial community during the barley yeast fermentation of stevia leaves and its correlation with antioxidant, antiobesity, and anti-inflammatory properties, as well as metabolites, were investigated using UPLC-Q-TOF-MS. Stevia was fermented using commercial TSB media (TSB 1, TSB 2, and TSB 3) and sucrose (Sucrose 1, Sucrose 3, and Sucrose 3) for 1, 3, and 5 days, respectively. Stevia ferments showed higher DPPH and ABTS radical scavenging capacity compared to samples incubated with sucrose for 5 days, and all six ferments inhibited nitric oxide production in a concentration-dependent manner in LPS-induced mouse macrophages. Furthermore, UPLC-QTOF-MS analysis identified 23 related substances, including 10 terpenoids, including rubusoside, steviolbioside, and rebadioside derivatives; dulcoside A; and phlomisoside II, which are indicators of stevia, as well as five flavonoids, four phenolic acids, and four fatty acids. We also identified the microbial community during fermentation via the next-generation sequencing of the 16S rRNA gene for bacteria and the internal transcribed spacer (ITS) gene for fungi. The results showed that TSB 1 and Sucrose 1 ferments were dominated by the pathogens Enterococcus hirae (58.93%) and Cronobacter sakazakii (80.92%), while samples fermented for more than 3 days were pathogen-free and dominated by lactic acid bacteria such as Pediococcus stilesii (73.37%). Microbial community analysis using the ITS region showed that Saccharomycopsis fibuligera, classified as a yeast rather than a mold, dominated the stevia fermentation regardless of the fermentation duration. In particular, the microbial community of the fermentation with a sugar solution was dominated by S. fibuligera by more than 99% throughout the fermentation periods of 1, 3, and 5 days. Finally, to apply the stevia ferments topically to human skin, skin irritation tests were performed on 30 volunteers. The results showed that the highly concentrated extracts (1 mg/mL) of all six stevia ferments were hypoallergenic. Taken together, these findings suggest that brewer's yeast fermented from stevia leaves with a sugar solution offers promise as a natural ingredient for use in functional foods and cosmetics.

This study investigates the impact of circular economy (CE) strategies on organizational resilience (OR) within the metal industry, focusing on a case study of a forging department in a large man-ufacturing company. The idea of the paper is to link the macroeconomic topic of circular economy (CE) with microeconomic and practical activities in the organization, exploring how CE principles can improve resource efficiency, sustainability, and organizational resilience. A systematic literature review and case study methodology were used to assess the relationship between CE and OR. The findings reveal that companies with higher circularity demonstrate better resilience, both in normal operations and during crises. Specifically, in the case study, the closure of the forging department, following a detailed analysis using the Inputs-Mediators-Outputs (IMO) model, emerged as the most sustainable option, yielding financial, environmental, and operational benefits. This decision aligned with the company’s long-term goals of energy efficiency and carbon neutrality. The research highlights the significance of integrating CE strategies with business processes to not only achieve sustainability but also to build a more adaptable and resilient organization. Future research should explore broader applications of this framework across different industries to strengthen the links between circular economy practices and organizational resilience.

Nigeria's upstream oil and gas sector is extensively contributing to the economic growth of the country, but the sector is plagued with challenges around corporate social responsibility (CSR) and taxation practices. Petroleum Industry Act (PIA) is introduced to tackle these challenges towards promoting sustainable development in Nigeria. The aim of this study is to explore the PIA’s provisions on CSR and taxation, identify the Act’s implementation challenges and improvement opportunities, propose an integrated framework for monitoring and evaluating the PIA’s impact on CSR and taxation over time, and recommend measures for enhancing PIA’s impact on CSR and taxation support for sustainable development in Nigeria's upstream oil and gas sector. This study adopts the qualitative desk review method to analyze existent literature, reports, and documents regarding PIA’s provisions on CSR and taxation. Findings reveal that the PIA’s provisions greatly emphasize CSR initiatives and taxation transparency in improving responsible ethical business behaviour. An integrated framework for monitoring and evaluating PIA’s impact over time is developed. This study concludes that the PIA's provisions can balance CSR and taxation practices for sustainable development. The study’s recommendations include using the integrated framework as a structured strategy for monitoring and evaluating the PIA’s impact. This study contributes to the discussion on the imperatives of ethical business practices and regulatory frameworks for sustainable development drive in the oil and gas sector.

The formation of hydrogen sulfide (H₂S) in petroleum reservoirs by anaerobic microbial activity is called biogenic souring of reservoirs and is a risk in the oil and gas industry as the compound is extremely toxic, flammable and corrosive. In this paper, we present a workflow and the tools to assess biogenic souring from a pragmatic engineering perspective. The retention of H₂S in the reservoir due to the reactions with iron-bearing rock minerals (e.g. siderite) is shown in a theoretical approach here and supported with literature data. Cases are given for two fields under secondary (waterflooding) and tertiary flooding with microbial enhanced oil recovery (MEOR). The use of the Monte Carlo method as a numerical modelling tool to incorporate uncertainties in the measured physical/chemical/ biochemical data is demonstrated as well. A list of studies conducted with different chemicals alone or in combination with various biocides to mitigate biogenic souring provides an overview of potential inhibitors as well as possible applications. Furthermore, the results of static and dynamic inhibition tests using molybdate are presented in more detail due to its promising mitigation ability. Finally, a three-step workflow for the risk assessment of biogenic souring and its possible mitigation is presented and discussed.

By introducing environmental mediator, for avoiding randomness in selecting indicators and subjectivity in deciding interaction path coefficients to reveal interaction mechanism among forest industry, ecology and environmental capacity, structural Pressure–State–Impact–Response (PSIR) and quantitative Structural Equation Modeling (SEM) are utilized with data on thirty–one provinces of China. We can find that: (i) forest industry has a negative influence on ecology, whereas ecology has a positive influence on industry; (ii) the destructive influence that industry has on ecology is much greater than the positive effect ecology has on industry; and (iii) environmental capacity plays a partial mediating role between industry and ecology. According to these results we can conclude that: (i) forest industry and ecology are not in a symbiotic relationship and have not reached a level of ecological security; (ii) the interaction between industry and ecology is in a period of transition from antagonistic to beneficial; and (iii) industry dominates ecology. However, we prospect the following advice: (i) methods of forest industry should be changed; (ii) new modes of industrial integration and circular economy should be developed; and (iii) the ability of the environment to sustain itself should be enhanced. The level of forest ecological security to discuss the symbiotic mechanism of industry and ecology will propose to be measured in future.

Nowadays, the fingerprinting methodologies of olive oils are dominated. They consider the entire analytical signal, which is acquired and recorded by the analytical instrument, directly from olive oil or isoleted fraction, i,e chromatogram. The shape and intensity of the recorded signal the instrumental fingerprint from the whole olive oil adulteration. Therefore, the methodolygy is based on the chemical composition (Fatty acids and Triglycerides compositions). However, Fatty acids composition as an indicator of purity suggests that linolenic acid content could be used as a parameter for the detection of extra virgin olive oil fraud with 5% of soybean oil. The adulteration could also be detected by the increase of the trans-fatty acid contents with 3% of soybean oil, 2% of corn oil and 4% of sunflower oil. The use of the ∆ECN42 proved to be effective in the Chemlali extra-virgin olive oil adulteration even at low levels: 1% of sunflower oil, 3% of soybean oil and 3% of corn oil. Therefore, compared to classical methods PCA and new approach of using LDA application could represent an alternative and innovative tool for faster and cheaper evaluation of extra-virgin olive oil adulteration.

Studies have demonstrated the critical role that safety plays in preserving favourable working conditions in the construction industry, which is necessary to accomplish goals. The aim of this research was to inform stakeholders in the construction industry in developing nations about the value of safety and possible strategies for influencing their opinions regarding safety protocols. The importance of safety to the construction sector, which is crucial to the advancement of the country, has also been emphasized. However, due to a lack of adequate safety understanding among stakeholders in the construction sector, the construction industry is characterized by a great deal of instability and hazard. To determine what factors, affect productive working conditions in the construction production, this study examined safety. A conceptual framework for safe working conditions in the construction sector was developed by considering several aspects, including the person dimension, environment factor, safety behaviour, organization features, technology, and incentives. It is now imperative to bring in these dimensions to improve the safe working conditions in the construction industry, particularly in the developing countries. By putting these safety factors into practice, the construction industry can reduce safety risks, lower the number of accidents and fatalities, cut expenses related to subpar safety performance, safeguard the reputation of construction companies, boost employee morale and satisfaction with their work, enhanced employee retention, reduced absenteeism, and enhanced sustainability goals. Additionally, the proposed conceptual framework is assured to be new and to be widely accepted in the developing nations. Based on this assumption the conceptual framework is designed.

There are considerable benefits in applying Artificial Intelligence to automation in modern industries including Oil and Gas Industries. Oil and Gas Industries have many complex systems in their production and flow line. The failure of gas equipment will have serious consequences including financial and environmental issues. Condition monitoring of oil and gas equipment provides the condition of components, machines, systems, equipment, data hardware, and even software. The predictive maintenance and industry 4.0 applications have more advantages in petrochemical industries to make a safer economic environment and this paper addresses the Artificial Intelligence (AI) application of condition monitoring for Oil and Gas Industries. To understand the effectiveness of AI in condition monitoring for oil and gas industries, a case study related to the condition monitoring of drilling machine is conducted and applied Artificial Neural Network (ANN) algorithm to analyze and predict the potential failures. The novelty of this work is the proposal of an approach for tool wear monitoring in drilling using acoustic emission sensors for feature extraction and considering wavelet packet decomposition for further analysis. The extracted features from WPD are given as input for ANN to identify the healthiness of the drill bit and machine. This work aims to find the effectiveness of AI-based condition monitoring in enhancing effectiveness of monitoring and the safety of equipment in Oil and Gas Industries.

Infill drilling is one of the most effective methods to improve the performance of poly-mer flooding. The difficulties related to infill drilling are determining the optimal numbers and placements of infill wells. In this study, an improved archimedes optimization algorithm with Halton sequence (HS-AOA) was proposed to overcome the aforementioned difficulties. First, to optimize the infill well placement for polymer flooding, an objective function that considered the economic influence of infill drilling was developed. Then, the novel optimization algorithm (HS-AOA) for infill well placement was developed by combining the AOA with the Halton se-quence. The codes were developed in MATLAB and connected to a commercial reservoir simula-tor CMG STARS to carry out the infill well placement optimization. Finally, the HS-AOA was compared to the basic AOA to confirm its reliability and then used to optimize the infill well placements for polymer flooding in a typical offshore oil reservoir. The results showed that the introduction of the Halton sequence into AOA effectively increased the diversity of the initial ob-jects in the AOA and avoided the HS-AOA trapping into the local optimal solutions. The HS–AOA outperformed the AOA. It was an effective approach to optimize the infill well placement for polymer flooding processes. In addition, infill drilling could effectively and economically im-prove the polymer flooding performance in offshore oil reservoirs. The NPV of the polymer flooding case with infill wells determined by HS-AOA reached 3.5 × 108 $, which was an increase of 7% over that of the polymer flooding case. This study presents an effective method for opti-mizing infill well placement for polymer flooding processes. It also can serve as a valuable refer-ence for other optimization problems in the petroleum industry, such as joint optimization of well control and placement.

Embracing Fourth Industrial Revolution(4IR) techniques is a need for a long-term sustainability and to do automation in the processes of Industrial and education sector. Rapid advancement in the information technology and other engineering technologies demand more proactive steps in the education institutes. In the post pandemic world, there is an increasing demand of changes in teaching and learning methodologies with the support of modern digital technologies. So, all of the teaching institutes need to have a significant step change in the areas of learning and teaching. The impact of 4 IR is more on the education sectors compared to previous generation’s industrial revolution. Keeping track of key technologies can be quite a challenge as they keep evolving at a very fast pace. Fourth Industrial revolution is the current technological digital revolution in which major focus is on cyber physical and biological systems such as Artificial Intelligence, Robotics, Internet on Things, Virtual Reality etc., The educators and institutions should establish the pedagogies and teaching with the aid of Industry 4.0 techniques to evolve education 4.0. So, it is very important to understand the challenges and competencies required about the implementation of 4IR by the faculty members and students who are currently studying in Higher Education Institutes (HEIs). This paper aim is to do a systematic review about industry 4.0 techniques and its application in relate to the online learning and teaching, change in pedagogies, enhancement of data management in HEIs, digital and virtual laboratories etc.

Land use and cover change (LUCC) is an important method to investigate the causes of global environment change. We utilized the emergy ecological footprint (EEF) model to construct a land-use change model to be used as a systematic measuring tool for monitoring sustainable development trends. In particular, we estimated the eco-security of the Cing-jing region as a case study so that responsible agencies can use it to maintain a balance between ecological preservation and tourism development. The results indicated the following: First, the ecological environment of the Cing-jing region satisfied the safety standard in 2008–2014; however, the related indices increased considerably. Second, the grey model predicted a decrease in 2015–2024 ecological carrying capacities of Cing-jing and a large increase in capita EFs, resulting in a larger ecological deficit and higher EFI. The eco-security from 2015–2024 was higher compared to 7 years ago and is predicted to reach the Grade 2 intermediate level in 2022; thus the Cing-jing region is gradually becoming ecologically unsustainable. Strengths of our study included the use of EEF theory in a quantitative analysis of slope lands for the effective evaluation of ecological security. Finally, we expanded our research to include ecological security issues.

This article deals with special curves similar to those known in mathematics as Lamé curves. Their equations have a certain similarity with the equations of Lamé curves. But these curves are more like ellipses in appearance. Like ellipses, they have major and minor axes. These are such curves that their major and minor semi-axis coincide with an ellipse but are different than an ellipse. The main feature of these curves is that for any triangle whose base coincides with the axis of a given curve and the vertex is on a given curve, the condition aⁿ+bⁿ=cⁿ is obtained. The number “n” is called the degree or rank of this curve. To distinguish this group of curves, we called them Elbe curves. The equations of these lines are also provided in the paper.

In Tunisia, olive is the most cultivated fruit crop while in the north where rainfall exceeded 400mm.year-1, the olive growing area is in widely extension in marginal soil with high slope gradient. Thus, the inclusion of cover crops is a sustainable solution to increase the ecosystem productivity, improve the soil fertility and oil yields. But, in Tunisia a few study were investigated the effect of legumes cover crop on the olive productivity. Therefore, the aim of this study was to evaluate the short-term (two cropping seasons s 2021 and 2022) effects of different seeded cover crops and soil management practices on the cover crops and soil characteristics, as well as enzymes activities and related microbial diversity. Six intercropping were tested in rainfed olive orchards (cv.Chétoui): Spontaneous vegetation (Spont), Wheat, Vetch, Oat, Fenugreek, mixture Vetch-Oat and compared to control (3 periodic tillage/year without intercropping). During the first cropping season, cover crops were cut as animal feed and only residues were incorporated into the soil. While, during the second year, all cover crops biomass were incorporated into the soil. Results indicate that the dry biomass and carbon uptake were significantly higher in grasses species (Wheat and Oat). But, highest level of nitrogen was found in Fenugreek cover crops. As compared to control, all cover crops including spontaneous vegetation increased soil organic matter and macronutrient level, mainly phosphorus. The most activity of β-glucosidase, phosphatase and arysulphatase was found in the cover crops plot of wheat and oat. In addition, this study improve that the utilization of the carbon sources was dominated by amides, amine and amino-acids in the fenugreek plot; while it was dominated by polymers and carboxylic acids in the case of wheat and oat.

Endocrine disruptors are molecules that can interfere with the proper functioning of the endocrine system and lead to harmful effects in living organisms. This review focuses on the impact of synthetic fragrances, which are commonly found in personal care and household products, on the endocrine system. The article discusses the different types of hormones in the body and how they interact with receptors to produce signals. It also explores how endocrine disruptors can interfere with hormone signaling and transport, leading to adverse effects in the body. This work underscores the crucial need for further research into the impact of synthetic fragrances on the endocrine system and the importance of using safer alternatives in personal care and household products.

The study of rare diseases is important not only for the individuals affected but also for the advancement of medical knowledge and a deeper understanding of human biology and genetics. The wide repertoire of structural information now available from reliable and accurate prediction methods provides the opportunity to investigate the molecular origins of most of the rare diseases reviewed in the Orpha.net database. Thus, it has been possible to analyze the topology of the missense mutations found in the 2,535 proteins involved in Mendelian rare diseases (MRD), which form the database for our structural bioinformatics study. The amino acid substitutions responsible for MRD show different mutation site distributions at different three-dimensional protein depths. We then predicted the depth-dependent effects of mutations for the 20,248 pathogenic variants that are present in our database. The results of this structural bioinformatics investigation are relevant, as they provide additional clues to mitigate the damage caused by MRD.

Improper disposal of waste plastic has caused serious ecological and environmental pollution problems. Transforming plastics into high value-added chemicals can not only achieve efficient recycling of waste plastics, but also an effective way to control white pollution. The catalyst selectively breaks the C-C bond of polyolefin plastic under heat treatment and converts it into liquid fuel, thus realizing sustainable recycling of plastics and has a good development prospect. This review provides a detailed overview of the current development of catalytic pyrolysis, catalytic hydrolysis, solvent decomposition and supercritical hydrothermal liquefaction for cracking plastics to make fuel oil. The reaction mechanism, influencing factors and promoting effects of catalysts in various degradation technologies are analyzed and summarized and the latest proposed tandem reaction for degrading plastics is briefly introduced. Finally, some optimization paths of waste plastic pyrolysis to fuel oil technology are proposed: synergies between mixed raw materials, in-depth exploration of catalysts, design and manufacture of reactors that match the pyrolysis technology. All these are important research directions for promoting the industrialization of plastic pyrolysis to fuel oil.

Waste cooking oil (WCO) recycled asphalt is facing issues regarding insufficient thermal oxidation stability and aging resistance. In this research, glycerol esterification was adopted to pretreat WCO, and the consequences of this treatment on the aging resistance and thermal stability of WCO were analyzed. The impacts of varying levels of esterification of WCO on the high-temperature, low-temperature performances, fatigue properties, as well as aging resistance of recycled asphalt were investigated. Furthermore, the mechanisms of regeneration and anti-aging of deeply esterified WCO recycled asphalt were revealed by Fourier transform infrared spectroscopy (FTIR) and gel permeation chromatography (GPC) tests. The results indicated that variations in the physical properties of WCO during the aging process were reduced, and its aging resistance was improved following glycerol esterification therapy. The initial thermal decomposition temperature was increased by approximately 115°C, which resulted in the enhancement of thermal stability significantly. Recycled asphalt obtained from deeply esterified WCO exhibited superior high-temperature, low-temperature performances and fatigue properties. Moreover, the thermal oxidation stability and aging resistance of recycled asphalt with deep-esterified WCO could be promoted by reducing the oxidation and volatilization of light components during the aging process.

The existing methods of oil palm Fresh Fruit Bunch (FFB) evacuation from in-field to temporary collection point which typically apply medium to large tractors, often result in unexpected soil compaction. Meanwhile, smaller size equipment indicates low working capacity and unable to perform direct unloading to collection bin. This paper addresses the challenge of FFB evacuation by focusing on preventing soil compaction, increasing working capacity and enabling direct unloading to collection bin. For this purpose, a 6x6WD transporter prototype with a scissor lift mechanism was developed. With the design, the transporter could evacuate FFB in both steep mineral terrain and low ground pressure peatland, able to carry FFB with capacity of 750 kg and provide direct unloading into collection bin. The average field working capacity of the transporter was found to be 15 tons day-1. This research offers insights for future designs of medium-sized FFB transporters with advanced unloading mechanisms.

Matters relating to preservation of environmental resources and climate change, social inclusion and diversity, and open and sound governance have rapidly gained global attention. However, little is known about the construction industry in meeting the environmental, social and governance (ESG) criteria towards sustainable development. In this study, the purpose is to identify the key ESG indicators for construction development. A systematic literature review was undertaken using data from Scopus, PubMed, Google Scholar, JSTOR, ProQuest, and Web of Science. The results show some of the key ESG indicators as climate resilience and green construction activities (at the project level), and active stakeholder engagement and effective project governance (at the firm level) and meeting environmental and social regulation requirements (industry/national level). The limitation of the article is in the sample size of twenty-six journal articles with future expectation of increment as ESG gain more acceptance in the construction industry. This study will be significant for the design of practice framework and policies on ESG in the construction industry. Comprehensively, this study presents relevant ESG indicators for construction management and presents essential information for future research.

Automobile industry is recognized as one of the most influential sectors shaping the global economies, societies, and individual lifestyles. Therefore, fierce competitions among different companies are continuously undergoing, and innovations deserve special attention to improve the competitiveness. In the past several years, additive manufacturing (AM) is emerging as an innovative technology in the applications of automobile industry with significant advantages over traditional techniques. As a result, increasing attention has been attracted to combining AM technology with the development of automobile industry. Currently, many automobile players are optimizing their industrial layout by incorporating with innovative AM techniques, and meanwhile, many research progresses have been achieved to meet the market demand. This article aims at presenting a timely review to conclude the recent advances in the application of AM techniques in automobile industry, focusing on the available AM techniques, printable materials, and the industry applications. The future research opportunities and challenges are also outlooked. Hopefully, this work can be useful to the related researchers, as well as the game players in the industry of this field.

This study examines the environmental challenges faced by Malaysian industries in adhering to industrial effluent regulations with the research question, what are the challenges in complying with environmental legislations from industries? It investigates the primary factors contributing to non-compliance and the perspectives, knowledge, and needs of Malaysian industries regarding environmental compliance. This study recommends the best strategy for promoting self-compliance. Thirteen stakeholders from various industries with environmental management experience were interviewed. Over the past seven years, these industries have shown low com-pliance with the Industrial Effluent Regulation 2009, prompting an exploration of their adaptability to regulations. Challenges identified include cost, employee attitudes, technology, management support, public complaints, and jurisdictional issues. Responses varied from divergent to unified viewpoints, highlighting the complexity of compliance issues. Respondents suggested enhancing compliance through behavioral changes, including incentives, enforcement, awareness, guidance, industry ratings, management commitment, and public disclosure of emissions. Suggestions for improvement and innovative solutions emerged based on participants' experiences, emphasizing the importance of continuous improvement. The study emphasizes the government's crucial role in ensuring regulation adherence but underscores the need for analyzing barriers and exploring alternative approaches. Understanding industry perspectives and strategies is essential for progress. Compliance, however, requires an analysis of the current challenges and adopting adaptive measures. It is important to understand industries' perspectives and strategies to move forward.

In an attempt to reuse fibrous textile waste and, at the same time, to address dye pollution in textile wastewater, waste cotton-based yarn was utilized as both a cheap and sustainable adsorbent and a precursor for carbon adsorbent production. Cotton and cotton/polyester yarn samples underwent thermal modification through carbonization followed by chemical activation with KOH. Various techniques including nitrogen adsorption-desorption isotherms, scanning electron microscopy, Fourier transform infrared spectroscopy, and surface charge determination were employed to analyze the morphological and surface properties of the cotton-based adsorbents. Adsorption properties were evaluated by testing the removal of selected cationic and anionic dyes from water. The impact of temperature, contact time, initial concentration, and pH of the adsorbate solution on adsorption was investigated, with experimental data analyzed using theoretical models. While carbonization alone did not significantly enhance adsorption properties, activated samples exhibited high efficacy in removing both cationic and anionic dyes from water. Despite the negative influence of the polyester component in the carbon precursor on the efficiency of activated samples in removing methyl orange, results indicated that activated cotton and cotton/polyester yarn could be used to prepare highly efficient adsorbents for the rapid removal of methylene blue from real wastewater samples.

The utilization of natural waxes to form oleogels has emerged as a new and efficient technique for structuring liquid edible oil into solid-like structures for diverse food applications. The objective of this study was to investigate the interaction between sunflower wax (SW) and monoglycerides (MGs) in olive oil oleogels and to assess their physical characteristics and storage stability. To achieve this, pure SW and a combination of SW with MGs in a 1:1 ratio were examined within a total concentration range of 6-12% w/w. The formed oleogels were characterized based on their microstructure, melting and crystallization properties, textural characteristics, and oxidative stability during storage. All the oleogels were shelf-stable, and as the concentration increased, the hardness of the oleogels also increased. The crystals of SW oleogels were long needle-like, while the combination of SW and MGs led to the formation of crystal aggregates and rosette-like crystals. The differential scanning calorimetry and FTIR showed that the addition of MGs led to different crystal structures. The oxidation results revealed that oleogels had low peroxide and TBARS values throughout the 28-day storage. These results provide useful insights about the utilization of SW and MGs oleogels for potential applications in the food industry.

Ammonium sulfate has been utilized in agriculture; however, there is a dearth of research on its application in maize cultivation subsequent to the implementation of nitrification inhibitors or coating. This study aims to analyze the impacts of various combinations of ammonium sulfate fertilizers on soil nutrients, plant nutrient uptake, yield, and fertilizer utilization efficiency in maize cultivation to ascertain the optimal and stabilized disposal method for ammonium sulfate. A completely randomized design was employed with five treatments (AU, the control using urea; AS, treatment using ammonium sulfate; ASN, treatment using ammonium sulfate with a nitrification inhibitor; ASG, treatment using oil-coated ammonium sulfate; ASD, treatment using oil-humic acid-coated ammonium sulfate). Results showed that: (1) Compared with AU and AS, ASN, ASG and ASD decreased the leaching rates of TN, NH4+-N and NO3-N to the 10-20 cm soil layer, and more residual N was obtained in 0-10 cm soil layer. The first-order kinetic equation Nt=N0(1-e-kt) can better fit the process of nitrogen accumulation and release, and the N release rate constant is AU>CK>AS>ASH>ASN>ASD; (2) Compared with AU and AS treatments, the plant dry weight, grain dry weight, spike width, spike length, and yields of maize increased by 8.85-11.08%, 12.98-14.15%, 2.95-3.52%, 5.50-5.65%, and 43.21-51.10% under ASG treatment respectively. The impact of effective spike number on maize yield was found to be significant, as demonstrated by the path analysis conducted in this study. Furthermore, the accumulation levels of nitrogen, phosphorus, and potassium within above-ground plants significantly increased under the ASG treatment compared to the AU and AS treatments. The partial productivity of nitrogen, phosphorus, and potassium increased by 1.43-1.51-fold under ASG treatment, while grain nitrogen balance, grain phosphorus balance, and grain potassium balance increased by 1.41-1.58-fold, 1.51-1.95-fold, and 1.15-l.96-fold respectively. The oil-coated ammonium sulfate, therefore, exhibited the optimal slow-release effect of nutrients, thereby achieving superior performance in enhancing maize production and efficiency.

Against the backdrop of the European Union's commitment to achieve climate neutrality by 2050, efforts to improve energy efficiency are being intensified. The manufacturing industry is a key focal point of these endeavors due to its high final electrical energy demand, while simultaneously facing a growing shortage of skilled workers crucial for meeting established goals. Expert systems (ESs) offer the chance to overcome this challenge by automatically identifying potential energy efficiency improvements and thereby playing a significant role in reducing electricity consumption. This paper systematically reviews state-of-the-art approaches of ESs aimed at improving energy efficiency in industry, with a focus on manufacturing. The literature search yields 1668 results, of which 62 articles published between 1987 and 2024 are analyzed in depth. These publications are classified according to the system boundary, manufacturing type, application perspective, application purpose, ES type, and industry. Furthermore, we examine the structure, implementation, utilization, and development of ESs in this context. Through this analysis, the review reveals research gaps, pointing toward promising topics for future research.

The development of biofuels and biodiesel industry specifically, has resulted in the generation of large amounts of glycerol as a surplus. The conversion of glycerol, into chemicals with indus-trial interest, through anaerobic fermentation using E. coli as a biocatalyst is an attractive alter-native to improve economic performance in the biodiesel industry, for example through the bi-otransformation of residual glycerol into ethanol. For 2019, the size of the global ethanol market was valued at $ 89.1 billion US dollar. Biodiesel can be produced from several materials like rapeseed, palm, soya, corn, palm kernel, frying oil or olive-pomace oil (OPO). The last, can be extracted from alperujo, byproduct of olive oil process. However, olive-pomace oil converting into biodiesel is not enough established to achieve a global olive-oil/biodiesel derived process with minimized waste generation. Traditionally biodiesel production process produces an equivalent of 10% by mass of glycerol as a waste or by-product. This work explores the conver-sion of residual glycerol into chemicals like ethanol and hydrogen with a focus on projecting raw material potential availability from OPO, contributing to the promotion of the use of biofu-els and biodegradable compounds.

With the increasing interest in CM as a potential source of nutrients and bioactive compounds, there arises a necessity to delve into methods for its processing and drying. Over recent decades, a significant amount of research has been conducted on the chemical composition of CM and its potential health benefits. Consequently, this study is directed towards examining CM drying technology, including an analysis of the influence of different drying methods on its chemical composition and nutri-tional properties. The objective of this review is to systematically summarize the available literature on CM drying processes and their impact on its chemical composition. Special attention is devoted to comparing various drying methods such as freeze-drying, spray drying, and freeze-drying, as well as investigating factors affecting the quality of dried CM. To achieve this goal, we scrutinize a series of studies published between 2003 and 2022 to identify optimal drying methods that promote the maximum preservation of CM's nutritional components and bioactive compounds. Additionally, we explore possibilities for reducing drying time to enhance production efficiency. This research is grounded in the analysis of data from diverse scientific research databases, including Scopus and Google Scholar, encompassing a systematic review of scientific literature and a comparative analysis of the obtained results.

Solvent free copolymerization of epoxides derived from fatty acid esters of waste cooking oil with phthalic anhydride using (salen)CrIII Cl as catalyst and n-Bu4NCl/DMAP as co-catalyst was carried out for the first time under microwave irradiation, where reaction time was reduced from number of hours to minutes. The polyesters were obtained with molecular weight (Mw = 3084-6740 g/mol) and dispersity values (D = 1.18-1.92), when (salen)CrIII Cl/n-Bu4NCl was used as catalysts. While in case of DMAP as a co-catalyst, polyesters with improved molecular weight (Mw = 5537-6925 g/mol) and narrow dispersity values (D = 1.07-1.28) were obtained even at reduced concentrations of (salen)CrIII Cl and DMAP. The obtained products were characterized and evaluated by attenuated total reflection-fourier transform infrared spectroscopy (ATR-FTIR), proton nuclear magnetic resonance (1H-NMR) spectroscopy, gel permeation chromatography (GPC) and thermogravimetric analysis (TGA) Techniques.

Biosolids from stabilized sludge presents a high fertilization potential due to its rich content of nutrients and organic matter. Three formulas of organo-mineral fertilizers based on biosolids were manufactured having at least 2 % N, 2 % P2O5, and 2 % K2O and characterized by classical and advanced methods. The content of N and P in the final formula was measured using specific reactants combined with VIS-nearIR spectroscopy. Additionally, all three formulas were characterized by advanced 1H NMR relaxometry, double-quantum and FT-IR spectroscopy. Structural characterization was performed using SEM, EDX and X-ray diffraction. Four dynamical components were identified in the T2-distribution showing that the rigid component is into a percentage larger than 90 %. In order to evaluate the release properties of organo-mineral fertilizers dynamic measurements of electric conductivity and pH were performed, by placing 0.25 g of formulas (V1, V2 and V3) in 200 ml of distillate water. It was found that V3 present the smallest release velocity, but release the largest amount of fertilizers. Two release mechanisms were also observed.

This study proposes and validates a novel combustion control system for Oil-Fired Boilers aimed at reducing air pollutant emissions through flame image prediction. The proposed system is easily applicable to existing ships. Traditional proportional combustion control systems supply fuel and air at fixed ratios according to the set steam load, without considering the emission of air pollutants. To address this, a stable and immediate control system is proposed, which adjusts the air supply to modify the combustion state. The combustion control system utilizes oxygen concentration predictions from flame images via SEF+SVM as control inputs, and applies Internal Model Control (IMC)-based Proportional-Integral (PI) control for real-time combustion control. Due to the complexity of modeling the image-based system, IMC parameter tuning through experimentation is essential for achieving effective control performance. Experiments conducted on a 3000 kg/h marine oil-fired boiler in actual operation optimized the controller parameters for stability and responsiveness, and validated their effectiveness. The results demonstrate the potential of the proposed system to improve combustion efficiency and reduce emissions of air pollutants. This study provides a feasible and effective solution for enhancing the environmental performance of marine oil-fired boilers. Given its ease of application to existing ships, it is expected to contribute to sustainable air pollution reduction across the maritime environment.

The effects of rare earth Ce on the microstructure and properties of cast pure copper were investigated through thermodynamic calculations, XRD analysis, mechanical testing, metallographic microscopy, and scanning electron microscopy (SEM). The experimental results demonstrate that the reaction between rare earth Ce and oxygen as well as sulfur in copper exhibits a significantly negative Gibbs free energy value, indicating a strong thermodynamic driving force for deoxidation and desulfurization reactions. Ce is capable of removing trace amounts of O and S from copper. Moreover, the maximum solid solubility of Ce in Cu falls within the range of 0.009% to 0.01%. Furthermore, Ce can refine columnar grains while enlarging equiaxed grains in as-cast copper.Upon addition of rare earth Ce, the tensile strength increased by 8.45%, elongation increased by 12.1%, and microhardness rose from 73.5HV to 81.2HV-an increase of 10.5%. Overall, rare earth Ce has been found to enhance both the microstructure and mechanical properties of cast pure copper.

Heat transfer fluids are used in various industrial systems to maintain them in perfect operating conditions. Extensive research efforts have been dedicated to enhance the thermal properties of these heat transfer fluids to improve their efficiency. Developing nanofluids is a potential candidate for such enhancements. This study investigates the impact of incorporating TiO2 nanoparticles into two types of oils: transformer oil (NYTRO LIBRA) and virgin coconut oil (manufactured by Govi Aruna Pvt. Ltd.) at different temperatures and with varying volume fractions. The nanofluids were prepared using a two-step method by adding CTAB (Cetyltrimethylammonium bromide) surfactant. To minimize nanoparticle agglomeration, this study employed relatively low-volume fractions. Thermal properties by means of thermal conductivity, thermal diffusivity, and volumetric heat capacity were measured in accordance with ASTM (American Society for Testing and Materials) standard methods, using a multifunctional thermal conductivity meter (LAMBDA thermal conductivity meter). The measured thermal conductivity values were compared with theoretical models and previous research findings. It was confirmed that the modification of thermal properties was enhanced by doping TiO2 nanoparticles with different volume fraction.

Regular regimes of oil and oil products pipelines are studied. The problem is to develop an algorithm of effective pipeline system control that ensures the fulfillment of specified boundary conditions at the system boundaries. The product is pumped in batches, the flow is characterized by a change in temperature and pressure flow parameters over time. The developed solution method uses the principle of decomposition in the sense that each computational iteration is im-plemented in 3 stages, in three nested loops. The inner cycle is connected with the material bal-ance relations, at the next cycle the flow equations are introduced and the fulfillment of the 2nd Kirchhoff's law is monitored. If the flow process is significantly affected by temperature, then an external cycle is also implemented, correcting the solution so that the energy conservation equa-tion is satisfied. In the calculation procedure, some computational difficulties may arise, which consist in choosing an appropriate optimization method. On a specific example, the possibility of using various library programs to solve the problem was checked. The developed method is suita-ble for the analysis of systems of arbitrary topology. Since the method is not time-consuming, it can be recommended for online control of oil and oil products supply systems. The paper opens a new direction in the theory of hydraulic circuits. It uses both traditional methods of continuum mechanics and stochastic models.

The goal of the study presented in this article is to investigate interconnection issues of the Intelligent Electrical Networks (IENs) with the existing ones, as well as the deployment of the appropriate load forecasting demand techniques. The concept of IENs has recently emerged as a potential solution to the global energy problem, due to the more flexible dispersed production units that are involved. In the same context, additional issues, such as the reduction of production-transfer-distribution costs as well as power losses are analyzed as well, via the penetration of Renewable Energy Sources (RESs). To this end, it is necessary to use appropriate advanced infrastructure, where in combination with modern telecommunication networks will make possible the full exploitation of IENs. Moreover, to make the electricity system more efficient, to avoid voltage and frequency imbalance issues and to implement optimal production and consumption planning, the Electric Load Forecast (ELF) is a vital process and plays a key role in the planning as well as in the management of electricity systems. Therefore, recent state of the art approaches in ELF methods are discussed as well.

The fast fashion industry has a significant impact on the environment at every stage of the product life cycle. There is a lack of research in the literature on the impact of fast fashion on the environment through logistics and transport. In this area, the greatest environmental impact is caused by air emissions, which is very important from the point of view of climate change. Therefore, this article deals with the analysis of the carbon footprint resulting from the fast fashion logistics process. The identification and assessment of fast fashion companies' sustainability efforts in the area of transport-related emissions and sustainable transformation strategies was conducted using a case study method for selected brands (H&M Group; Inditex, Shein). The study uses secondary data available in non-financial reports from 2023. After analyzing the data and content in non-financial reports on transport-related emissions, sev-eral important conclusions emerge. As a dominant practice, companies emphasize their reliance on external frameworks and standards, in particular the Global Reporting Initiative and the Task Force on Climate-related Financial Disclosures. Companies prioritize reducing emissions from significant factors, such as production processes. The data disclosed in the reports (scope 1, 2, 3) are not clearly formulated, but they can be used to calculate the level of CO2 emission reduction/increase. The ar-ticle contains recommendations for companies to improve their reporting by including additional indicators expressing the efficiency of transport-related emissions.