Two methods for Pd nanoparticle synthesis were explored with three different carbide-derived carbon (CDC) support materials of which one was nitrogen-doped. These materials were studied for oxygen reduction reaction (ORR) in 0.1 M KOH solution. The prepared CDC/Pd catalysts were characterized using TEM, XRD and XPS. Using these methods, we can observe the influence of support materials for one-pot synthesis methods as we use the standard citrate method and polyol method with polyvinylpyrrolidone (PVP) as a capping agent. Comparing the two methods N-doping of carbon material resulted in smaller nanoparticles only in the case of citrate synthesis, suggesting that the influence of support is weaker using polyol method. Citrate method on CDC1, which was predominantly microporous led to a higher degree of agglomeration and larger particle formation in comparison to CDC2 and CDC3 supports, which possessed higher degree of mesoporosity. Smaller Pd particle sizes were achieved using citrate and NaBH4 in comparison to the ethylene glycol-PVP method. CDC2 and CDC3 did not show significant difference suggesting that the N-doping did not have much of an influence on the ORR. Highest SA value was observed on CDC1/Pd_Cit, which could be attributed to formation of larger particles and agglomerates.

A four-step synthesis of bifunctional, noncovalent organocatalysts based on the chiral (1R,2R)-cyclohexane-1,2-diamine scaffold containing a 1,2-benzenediamine H-bond donor was developed. Nucleophilic aromatic substitution of the 2-fluoronitrobenzene derivative with the commercial (1R,2R)-cyclohexane-1,2-diamine was followed by selective alkylation of the primary amino group, reduction of the aromatic nitro group and final derivatization of the primary aromatic amino group, i.e. acylation, sulfonation, reductive alkylation and arylation, leading to the four subtypes of organocatalysts. All new compounds were fully characterized. The prepared organocatalysts (32 examples) were tested in the Michael addition of acetylacetone to trans-β-nitrostyrene, yielding the addition product with incomplete conversions (up to 93%) and enantioselectivities of up to 41% ee.

The open data market is growing, driven by laws requiring governments to make data publicly available. However, the true value of this market lies in the products and services derived from open data. In Slovenia, the open data market has been growing since 2015, especially in the field of mobility. Platforms such as Avtolog.si facilitate the retrieval of vehicle data via vehicle identification numbers, while tocen.si, ojpp.si, and brezavta.si aggregate mobility data, focusing on sustainable and micromobile public transportation services. These platforms use open government data and private sector open data, and are freely accessible. This study examines the use of open data in the Slovenian mobility applications and similar solutions developed in other countries. By mapping these applications, we gain valuable insights into potential advances in the field, and provide a useful resource for future developers worldwide. By focusing on the socio-economic impact of these innovations, the study identifies methods for evaluating such applications. This approach highlights how transforming open data into user-friendly products and services can deepen our understanding of their broader societal and economic benefits. While open data is valuable in its own right, its full transformative potential is realized through innovative products that support sustainable lifestyles and promote environmentally conscious behavior.

Hexakis(2-alkoxy-1,5-phenyleneimine) macrocycles were synthesized using a simple one−pot procedure through by precipitation−driven cyclization. The acetal−protected AB−type monomers, 2-alkoxy-5-aminobenzaldehyde diethyl acetals, underwent polycondensation in water or acid−containing tetrahydrofuran. The precipitation−driven cyclization based on imine dynamic covalent chemistry and π−stacked columnar aggregation played a decisive role in the one−pot synthesis. The progress of the reaction was analyzed by MALDI−TOF mass spectrometry. The macrocycles with alkoxy chains were soluble in specific organic solvents such as chloroform, allowing their structures to be analyzed by NMR. The shape−anisotropic, nearly planar, and persistent macrocycles aggregated into columnar assemblies in polymerization solvents, driven by aromatic π−stacking. The octyloxylated macrocycle OcO−Cm6 exhibited an enantiotropic columnar liquid crystal−like mesophase between 165°C and 197°C. In the SEM image of (S)-(−)-3,7-dimethyloctyloxylated macrocycle (−)BCO-Cm6, columnar substances with a diameter of 100−200 nm were observed. The polymerization solution for 2-(2-methoxyethoxy)ethoxy)ethoxylated macrocycle (TEGO−Cm6) gelled and showed thixotropic properties by forming a hydrogen bond network.

Economic, social, and environmental sustainability are the results of efforts aiming to improve all aspects of milk production, respecting animal welfare and improving herd health. An epidemi-ological study was designed to assess the role of contagious pathogens (S. aureus and S.agalactiae) in a cohort of 120 dairy herds located in the southern regions of Italy. Milk quality was assessed using certified methods, and the prevalence of mastitis pathogens in bulk tank milk was determined using quantitative polymerase chain reaction. Welfare scores were assessed using a scoring card that have more than 100 items, including animal-based measurements. Statistical analyses were performed using general lineal model and logistic regression procedures. The results showed that S. aureus had a significant negative effect on the amount of milk components delivered to the dairy plant, and on the level of welfare. Whereas, the presence of S.agalactiae did not show any significant association. The major risk factors associated with the presence of S.aureus were also identified to help prioritise control programs. These results support the “One Sustainability” approach im-plying that an increase of animal productivity is related to the improvement of animal health and welfare and potentially leading to the mitigation of greenhouse gas emissions.Economic, social, and environmental sustainability are the results of efforts aiming to improve all aspects of milk production, respecting animal welfare and improving herd health. An epidemi-ological study was designed to assess the role of contagious pathogens (S. aureus and S.agalactiae) in a cohort of 120 dairy herds located in the southern regions of Italy. Milk quality was assessed using certified methods, and the prevalence of mastitis pathogens in bulk tank milk was determined using quantitative polymerase chain reaction. Welfare scores were assessed using a scoring card that have more than 100 items, including animal-based measurements. Statistical analyses were performed using general lineal model and logistic regression procedures. The results showed that S. aureus had a significant negative effect on the amount of milk components delivered to the dairy plant, and on the level of welfare. Whereas, the presence of S.agalactiae did not show any significant association. The major risk factors associated with the presence of S.aureus were also identified to help prioritise control programs. These results support the “One Sustainability” approach im-plying that an increase of animal productivity is related to the improvement of animal health and welfare and potentially leading to the mitigation of greenhouse gas emissions.

Several pathotypes of enteric E. coli have been identified. The group represented by Shiga toxin-producing E. coli (STEC) is of particular interest. Raw milk and raw milk products are significant sources of STEC infection in humans; therefore, identifying pathogens at the herd level is crucial for public health. Most national surveillance programs focus solely on raw milk and raw milk cheeses that are ready for retail sale, neglecting the possibility of evaluating the source of contamination directly at the beginning of the dairy chain. In order to assess the viability of new molecular methodologies applied to raw milk filters enabling the identification of the presence of STEC serotypes in milk production and apply the same methods to identify the presence of these pathogens in calf feces we analyzed, through a commercial real-time PCR assay, a total of 290 samples coming from 18 different dairy herds; 88 bulk tank milk (BTM), 104 raw milk filters (RMF) and 98 calves’ feces samples. In total 3.4% of BTM, 41.4% of RMF and 73.4% of calves’ feces tested positive for stx presence, supporting our hypothesis that BTM is not a suitable matrix to assess the STEC presence at herd level, underestimating it. Our conclusion is that the surveillance program needs critical and extensive improvements such as RMF and calves’ feces analysis implementation in order to be more efficient in detecting and preventing STEC infections. The epidemiology of these infections and the characteristics of the pathogen clearly show how a One Health approach will be pivotal to improve our capabilities to control the spread of these infections.

Chitosan decorated copper nanoparticles catalysts (CSCuNPs) were synthesized via reduction methods utilizing green protocol. The CSCuNPs catalysts were tested for the synthesis of quinoline derivatives utilizing one-pot multicomponent reaction (MCR) under ultrasonic irradiation. The best catalyst (Cu-CS-NPs) that provided good conversion reaction yield and high turnover frequency (TOF) was characterized using FTIR, TGA, XRD, TEM and XPS techniques. Generalization of the scope of the proposed catalytic process was studied using different aldehydes. Excellent products yield and high TOF in even shorter reaction time (~5 min) was attained. Recyclability performance of the catalyst over five times re-use without detectable loss in product yield was recorded. The current method is green process utilizing environmentally benign catalyst and considered to be promising sustainable protocol for the synthesis of fine chemicals.

The development of a method to produce coumarins unsubstituted on the pyranic nucleus catalyzed from Wells–Dawson heteropolyacid (H₆P₂W₁₈O₆₂), phenol derivatives and ethyl 3,3-diethoxypropionate using Pechmann condensation under solvent-free conditions is described. This catalytic method was also applied successfully to synthesize various substituted coumarins, including the corresponding phenols and ethyl 3,3-diethoxypropionate. This work provides a novel, cheaper and safer way to syhthesize coumarins unsubstituted on the pyranic nucleus.

The present article describes a one-pot and cascade mode process using biocompatible/biodegradable reagents, for directly and simply obtaining surfactant compositions of mixtures of D-mannuronic acid and L-guluronic acid directly from oligoalginates or semi-refined alginates (mixtures of alginate, cellulose, hemicellulose, laminaran and fucan). Simple treatments of partial purification of the reaction crudes (elimination of the salts and/or the residual fatty alcohols) or isolation of the surfactant compositions result in derived compounds and in compositions having performance levels appropriate to applications in detergency. In addition, the challenging extension of this cascading one-pot synthesis technology to crude milled brown seaweeds was successfully carried out to provide promising surface-active compositions made up of alkyl uronate and alkyl glycoside monosaccharides.

The studied solar pot is a recent invention, which gained a utility model protection in 2021 from the Hungarian Intellectual Property Office under patent number 5489. The device is made for environmentally friendly cooking or heating (by utilizing solar energy) of foods and liquids. Its structure is similar to a double pipe heat exchanger, it has an outer mantle and an inner cooking tank. The goals of the paper are proposing a new physically-based mathematical model describing the solar pot and carrying out computer experiments with it, assembling an experimental system of the pot connected with a solar collector and performing measurements on it. Based on the results, the solar pot can successfully be used for cooking or sterilizing foods or liquids during the studied time period, in Hungary.

The green synthesis of metallic nanoparticles is an emerging and promising field owing to its environmentally friendly nature and diverse applications. In this article, a new technology for the green synthesis of functional ultrastable biopolymer gold nanoparticles is introduced. This approach employs thiolated single-stranded DNA (ssDNA-SH) aptamers instead of conventional self-assembled monolayers, resulting in the production of highly stable aptamer-tagged gold-core-shell nanoparticles. A comprehensive discussion on the use of glucose as a simple reducing agent for the green synthesis of Au nanoparticles and the utilization of ssDNA-SH aptamers as smart and biologically functional capping agents is provided. The potential of this innovative approach for the green synthesis of nanoparticles is demonstrated through a case study involving the use of the naked eye for qualitative detection of human fungal infections caused by Candida albicans for women's health.

Silica aerogels and their derivatives have outstanding thermal properties with exceptional values in the thermal insulation industry. However, the brittle nature restricts its large-scale commercialization. Thus, enhancing their mechanical strength without affecting their thermal insulating properties is essential. Therefore, for the first time, highly thermally stable Poly(acrylamide-Co-acrylic acid) partial sodium salt is used as a reinforcing polymer to synthesize hybrid P(AAm-CO-AAc)-silica aerogels via epoxy ring-opening polymerization in the present study. Functional groups in P(AAm-CO-AAc) partial sodium salts, such as CONH2 and COOH, acted as nucleophiles for the epoxy ring-opening reaction with (3-glycidyloxypropyl)trimethoxysilane, which resulted in a seven-fold enhancement in mechanical strength compared to that of a pristine silica aerogel while maintaining the thermal conductivity at less than 30.6 mW/mK and porosity of more than 93.68%. Moreover, the hybrid P(AAm-CO-AAc)-silica aerogel demonstrated improved thermal stability up to 343 ⁰C owing to the synergetic effect between P(AAm-CO-AAc) and the silica aerogel, corresponding to thermal stability and strong covalent bonding among them. These excellent results illustrate that this new synthetic approach for producing hybrid P(AAm-CO-AAc)-silica aerogels is useful for enhancing the mechanical strength of a pristine silica aerogel without impairing its thermal insulating property and shows potential as an industrial heat insulation material.

Automatic Milking Systems (AMS) are revolutionizing the dairy industry by boosting herd effi-ciency, primarily through increased milk yield per cow and reduced labor costs. The performance of milking machines, whether traditional or automated, can be evaluated using advanced vacuum meters through dynamic testing. This process involves scrutinizing the system and milking rou-tine to identify critical points, utilizing the VaDia™ logger (BioControl AS, Rakkestad, NO). Vacuum recordings were downloaded and analyzed using the VaDia Suite™ software under the guidance of a milking specialist. Access to data from AMS across various manufacturers and herds facilitated a retrospective study aimed at describing and comparing key milk emission parameters for different AMS brands while identifying potential mastitis risk factors. Using proper statistical procedures of SPSS 29.1 (IBM Corp, USA), researchers analyzed data from 4,878 individual quarter milkings from cows in 48 dairy herds. Results indicated significant variability in milking pa-rameters associated to quarter milk yield and AMS brand. Notably, despite AMS standardizing teat preparation and stimulation, the study revealed a surprisingly high frequency of two major mastitis risk factors—bimodality and irregular vacuum fluctuations—occurring more frequently than in conventional milking systems. This study, one of the few comparing different AMS brands and their performance, highlights the crucial role of dynamic testing in evaluating AMS perfor-mance under real-world conditions.

Obesity is a global public health problem and the environment as its major determinant. To identify interventions an evidence base is warranted. To this aim we investigate the relationship between the consumption of foods and eating locations (like home, school/work and others) in British adolescents, using data from the UK National Diet and Nutrition Survey Rolling Program (2008–2012 and 2013-2016). Cross-sectional analysis of 62,523 food diary entries from this nationally representative sample then focused on foods contributing up to 80% total energy to the daily adolescent´s diet. Correspondence Analysis (CA) was first used to generate food-location relationship hypotheses and Logistic Regression (LR) to quantify the evidence in terms of odds ratios and formally test those hypotheses. The less-healthy foods that emerged from CA were chips, soft drinks, chocolate and meat pies. Adjusted Odds Ratios (99% CI) for consuming specific foods at a location “Other” than home (H) or school/work (S) in the 2008-12 survey sample were: for soft drinks 2.8 (2.1 to 3.8) vs. H and 2.0 (1.4 to 2.8) vs. S; for chips 2.8 (2.2 to 3.7) vs. H and 3.4 (2.1 to 5.5) vs. S; for chocolates 2.6 (1.9 to 3.5) vs. H and 1.9 (1.2 to 2.9) vs. S; and for meat pies 2.7 (1.5 to 5.1) vs. H and 1.3 (0.5 to 3.1) vs. S. These trends were confirmed in the 2013-16 survey sample. Interactions between location and BMI were not significant in either sample. In conclusion, our study showed that adolescents are more likely to consume specific less-healthy foods at locations away from home and school/work, irrespective of BMI. Such locations include leisure places, food outlets and “on the go”, hence public health policies to discourage less-healthy food choices in these locations is warranted for all adolescents.

A facile and novel synthesis of thirteen 2-amino-3-cyanopyridine derivatives 5(a-m), by a one-pot multicomponent reaction (MCRs), is described for the first time, starting from aromatic aldehydes, malononitrile, methyl ketones, or cyclohexanone and ammonium acetate in the presence of the nanostructured diphosphate Na2CaP2O7 (DIPH) at 80 °C, under solvent-free conditions. These compounds were synthesized in short reaction times with good to excellent yields (84-94%). The diphosphate Na2CaP2O7 is used as an efficient catalyst, environmentally, easy handling, non-toxic, stable, and reusable. Our study was strengthened by the synthesis of five new pyrido[2,3-d]pyrimidine derivatives 6(b, c, g, h, j) by intramolecular cyclization of 2-amino-3-cyanopyridines 5(b, c, g, h, j), with formamide. The synthesized products were characterized by FT-IR, SEM, XRD, TEM, 1H NMR, 13C NMR, TLC, and BET. The operating conditions were optimized using a model reaction in which the catalyst amount, temperature, time, and solvent effect were evaluated. The antibacterial activity was tested against Gram-positive and Gram-negative strains for the synthesized compounds.

In contemporary design practices, there is a disconnect between the design techniques used for early-stage design experimentation and performance analysis, and those used for the manufacture and construction. This study addresses the problems in developing an integrated digital design workflow and provides a research framework for integrating environmental performance requirements with robotic manufacturing processes on a construction site. The proposed method enables the user to import a design surface, identify design parameters, set several environmental performance goals, and thereafter simulate and select a robotic building strategy. Based on these inputs, design alternatives are developed and evaluated, considering their robotically simulated constructibility, in terms of their performance criteria. To validate the proposed method, the design is evaluated in an experiment wherein a double-skin facade perforation is generated using the proposed methodology. The results suggest a heuristic feature to improve the simulated robotic constructibility. Moreover, the functionality of the prototype is demonstrated.

Fine chemicals are produced in small annual volume batch processes (often <10,000 tonnes per year), with a high associated price (usually > $10/kg). As a result of their usage in the production of speciality chemicals, in areas including agrochemicals, fragrances and pharmaceuticals, their necessity will remain high for the foreseeable future. This review article assesses current methods used to produce fine chemicals with heterogeneous catalysts, including both well-established methods as well as newer experimental methods. A wide range of methods utilising microporous and mesoporous catalysts has been explored, including their preparation and modification before use in industry. Their potential drawbacks, as well as benefits, have been analysed, with their feasibility compared to newer, recently emerging catalysts. The field of heterogeneous catalysis for fine chemical production is a dynamic and ever-changing area of research. This deeper insight into catalytic behaviour and material properties will produce more efficient, selective, and sustainable processes in the fine chemical industry. The findings from this article will provide an excellent foundation for further exploration and a critical review in this field of fine chemical production using micro- and mesoporous heterogeneous catalysts.

Fluorinated compounds and co-enzymes are being widely researched and employed throughout research community because of their versatile physical, chemical and biological properties. In this work, we synthesized NiS-NiO/S-g-C3N4, a highly effective photocatalyst for C(sp3)-F bond activation and the regeneration of coenzyme (1,4-NADH) employing a new and ecologically acceptable route. The obtained photocatalyst exhibited important photocatalytic properties, such as good solar light harvesting ability, suitability of the optical band-gap, and facilitating efficient charge migrations. As a result, the newly designed NiS-NiO/S-g-C3N4 photocatalyst shows the excellent yield for regenerations of 1,4-NADH (51%). Further, a method of combining C(sp3)-F bond activation with photocatalysis has been demonstrated that represents a very powerful and sustainable approach, that can be a major breakthrough for the field of pharmaceutical.

Dirofilaria immitis and D. repens are the two most widespread and important species of mosquito-borne nematodes, posing a significant threat to veterinary health, particularly affecting canines and felines. While D. immitis causes cardiopulmonary dirofilariasis, D. repens causes subcutaneous infections in dogs and other carnivores. Despite extensive knowledge about the aforementioned parasites, little is known about their natural vectors in Serbia. Thus, the aim of this study was to: i) further map out Dirofilaria sp. hotspots in the Vojvodina Province, ii) detect positive mosquito species which can provide insights in how the nematodes spread and adapt to the environmental conditions, and iii) analyze the blood fed mosquitoes females of species found infected to identify the potential source of parasite infection. A total of 2,902 female mosquitoes were collected across 73 locations during 2021 and 2022. Molecular biology methods, based on conventional PCR, were used to analyze non-blood fed (2,521 specimens) and blood fed (381 specimens) mosquito females, in order to detect filarial nematode presence and identify blood meal sources respectively. When the parasite genome was detected, the amplicon (COI gene, 650 bp fragment) was sent for Sanger sequencing, further confirming the presence of nematodes and species assignation. D. immitis was detected in three Culex pipiens mosquitoes collected in XXXX (location and date), while Setaria tundra was detected in Aedes vexans and Aedes caspius. This work adds two new locations where D. immitis occurs in Vojvodina, and is the first report of S. tundra on the territory of Serbia. Blood meal analysis provided insights into the preferences of mosquitoes that were positive for Dirofilaria sp. and S. tundra.

In contemporary design practices, there is a disconnect between the design techniques used for early-stage design experimentation and performance analysis, and those used for the manufacture and construction. This study addresses the problems in developing an integrated digital design workflow and provides a research framework for integrating environmental performance requirements with robotic manufacturing processes on a construction site. The proposed method enables the user to import a design surface, identify design parameters, set several environmental performance goals, and thereafter simulate and select a robotic building strategy. Based on these inputs, design alternatives are developed and evaluated, considering their robotically simulated constructibility, in terms of their performance criteria. To validate the proposed method, the design is evaluated in an experiment wherein a double-skin facade perforation is generated using the proposed methodology. Initial results suggest a heuristic feature to improve the simulated robotic constructibility. Moreover, the functionality of the prototype is demonstrated.

Artificial Intelligence and especially machine learning have noticed rapid advancement on image processing operations. However, its involvement in the architectural design is still in its initial stages compared to other disciplines. Therefore, this paper addresses the issues of developing an integrated bottom up digital design approach and details a research framework for the incorporation of Deep Convolutional Generative Adversarial Network (GAN) for early stage design exploration and generation of intricate and complex alternative facade designs for urban infill. This paper proposes a novel building facade design by merging two neighboring building’s architecture style, size, scale, openings, as reference to create a new building design in the same neighborhood for urban infill. This newly produced building contains the outline, style and shape of the parent buildings. A 2D urban infill building design is generated as a picture where 1) neighboring buildings are imported as a reference using mobile phone and 2)iFACADE decode their spatial adjacency. It is depicted the iFACADE will be useful for designers in the early design stage to generate new façades depending on existing buildings in a short time that will save time and energy. Besides, building owners can use iFACADE to show their architects their preferred architecture facade by mixing two building styles and generating a new building. Therefore, it is depicted that iFACADE can become a communication platform in the early design stages between architects and owners. Initial results properly define a heuristic function for generating abstract design facade elements and sufficiently illustrate the desired functionality of our developed prototype.

This study analyzes how Perceived Credibility of a 360-degree feedback and Evaluation of Outcome impact on ratees’ attitudes towards behavioral change. The study adopts a qualitative-quantitative mixed method approach. Reasoned Action Theory was selected as the theoretical framework, and ten 360-degree assessment ratees were interviewed on their perceived credibility, evaluation of outcome and attitude toward behavioral change in the 360-degree assessment practices. The qualitative inputs were analyzed under the methodology of grounded theory. Additional 159 respondents participated in the quantitative research phase of the research to validate the findings in the qualitative research phase. It was validated that Perceived Credibility, Evaluation of Outcome has impact on Attitude Toward Behavioral Change in 360-degree assessment.

In this study, a summary of the processes performed on the SPL for recycling, reduction in toxicity and treatment were examined on an industrial and laboratory scale. In writing this research, an attempt has been made to address the useful processes that have taken place in this field. Spent pot lining or SPL is a type of solid waste that is produced in the aluminum production process. After 3 to 8 years, the cathode blocks become problematic and can no longer be used, and need to be replaced due to adverse effects on cell function. SPL is known to be a hazardous waste to nature due to its fluoride and cyanide content. Research has shown that SPL ingredients have destructive and very dangerous effects on human DNA, which is why they are so important to maintain and recycle.

ATP is an essential molecule in many biocatalytic processes. The industrial implementation of these processes is hampered by the fact that they require stoichiometric quantities of this expen-sive co-factor. To avoid this problem, recycling systems are needed. This study characterizes a putative polyphosphate kinase enzyme from Burkholderia cenocepacia that can regenerate ATP from AMP. Sequence analysis shows that BcPPK2-III exhibits the characteristic structural motifs of known PPK2 enzymes, including conserved motifs Walker A and B, and the subclass-specific res-idue E137. Molecular docking simulations showed ADP had the highest binding affinity (-7.340 kcal/mol), followed by AMP (-7.284 kcal/mol), with ATP having the lowest affinity (-6.464 kcal/mol). The enzyme was overexpressed in E. coli. Protein expression and purification were monitored by SDS-PAGE and quantified by densitometric analysis. Enzymatic activity assays re-vealed that BcPPK2-III converts 70% ATP with a TTN of 334,000 after 24 hours and remains sta-ble over a pH range of 6-9 and temperatures up to 70°C. BcPPK2-III shows significant potential for industrial ATP regeneration and offers high conversion rates and stability. The enzyme's high conversion rate and stability make BcPPK2-III a promising candidate for the improvement of bio-catalytic processes that rely on ATP at industrial level.

In this study, a simple, easy and convenient fluorescent sensing system for detection of vascular endothelial growth factor (VEGF) based on VEGF aptamers, aptamer-complementary fluorescence-labeled probe and streptavidin magnetic beads was developed in only one single tube. The VEGF is the most important biomarker in cancer angiogenesis, and is investigated that serum VEGF level was various according to the different type and course of cancers. Hence, efficient quantification of VEGF is able to improve the accuracy of cancer diagnosis and precision of disease surveillance. In this research, the VEGF aptamer was designed to be able to bind with the VEGF by forming G-quadruplex secondary structures, and then the magnetic beads would capture the none-binding aptamers due to none steric interference, and finally, the fluorescence-labeled probes were hybridized with the aptamers captured by the magnetic beads. Therefore, the fluorescent intensity in the supernatant would specifically reflect the present of VEGF. After an overall optimization, the optimal conditions for detection of VEGF were as followed, KCl, 50 μM; pH 7.0; aptamer, 0.1 μM and magnetic beads, 10 μL (4 μg/μL). The VEGF could be well quantified within a range of 0.2-2.0 ng/ml in plasma, and the calibration curve possessed a good linearity (y = 1.0391x + 0.5471, r = 0.998). The detection limit (LOD) was calculated to be 0.0445 ng/mL according to the formula (LOD = 3.3×σ/S). The specificity of this method was also investigated under the appearance of many other serum proteins, and the data showed the good specificity in this aptasensor-based magnetic sensing system. This strategy provided a simple, sensitive and selective biosensing platform for detection of serum VEGF. Finally, it was expected that this detection technique can be promoted to more clinical applications.

The seed habit is the most complex and successful method of sexual reproduction in vascular plants. It represents a remarkable moment in the evolution of plants that afterwards spread on land. In particular, seed size had a pivotal role as for evolutionary success and agronomic trait, especially in the field of crop domestication. Given that crop seeds constitute one of the primary products for consumption, it follows that seed size represents a fundamental determinant of crop yield. This adaptative feature is strictly controlled by genetic traits from both maternal and zygotic tissues, although seed development and growth are also affected by environmental cues. Despite being a highly exploited topic for both basic and applied research, there are still many issues to be elucidated as for developmental biology as well as for agronomic science. This review addresses a number of open questions related to cues that influence seed growth and size, and how developmental processes are influenced by them. Besides, new insights on the genetic-molecular control of this adaptive trait are presented.

In this paper, we consider the Cauchy problem of a time fractional nonlinear diffusion equation. According to the Kaplan’s first eigenvalue method, we first prove the blow-up of the solutions in finite time for some sufficient conditions. We next give sufficient conditions for the existence of global solutions by using the result of Zhang and Sun. In conclusions, we find the second critical exponent for the existence of global and non-global solutions via the decay rates of the initial data at spatial infinity.

One of the oldest problems in physics is that of calculating the motion of N particles under a specified mutual force: the N-body problem. Much is known about this problem if the specified force is non-relativistic gravity, and considerable progress has been made by considering the problem in one spatial dimension. Here I review what is known about the relativistic gravitational N-body problem. Reduction to one spatial dimension has the feature that gravitational radiation is absent, thereby allowing for a clear comparison between the physics of one-dimensional relativistic and non-relativistic self-gravitating systems. After describing how to obtain a relativistic theory of gravity coupled to N point particles, I discuss in turn the 2-body, 3-body, 4-body, and N-body problems. Quite general exact solutions can be obtained for the 2-body problem, unlike the situation in general relativity in 3 spatial dimensions for which only highly specified solutions exist. The 3-body problem exhibits mild forms of chaos, and provides one of the first theoretical settings in which relativistic chaos can be studied. For N4 other interesting features emerge. Relativistic self-gravitating systems have a number of interesting problems awaiting further investigation, providing us with a new frontier for exploring relativistic many-body systems.

Background: One challenge in implant dentistry is to reduce marginal bone resorption to avoid long-term esthetic and biological complications. Sub-gingival implant placement has been suggested as a suitable strategy. Methods: 38 healthy patients were enrolled to receive bone level (BL – Control group) or 2 mm sub-crestal (SC - Test group) conical connection, platform-switched implants. An immediate tissue level abutment was used in the Test group by following a One Time Abutment (OTA) restorative procedure. Marginal Bone Modification (MBM) was calcu-latied on standardized radiographs at surgery (T0), loading (T1), and 6 months (T2) and 12 months after loading (T3), and cathegorised in Bone Loss (BL) if the resorption occurred below the implant neck and Bone Remodeling (BR) if above. Pocket probing depth (PPD), Bleeding on probing (BoP) and Plaque Index (PI) were also collected. Results: The mean MBM in the test group after 12 months was 0.61mm, compared to 0.52mm in the control group. However, no BL was observed in the test group, as the MBM completely occurred above the implant neck as BR, whilst in the control group MBM corresponded in total to BL. The average PPD was 2.38mm in the test group and 3.04mm in the control group after 12 months, BoP 50% and 43%, PI 33% and 19.44% respectively. Conclusions: Sub-crestal conical connection, platform-switched implants could be a suitable clinical choice to avoid BL with exposure of the treated implants surfaces.

We investigated the micro-threaded stem taper surface and the impact on premature failures, aseptic loosening, and infection. We have focused on the fretting, and crevice corrosion of micro-threaded tapers, as well as the characterization of microstructure and surface properties of two new and three retrieved Zweymüller stem tapers of cementless hip endoprostheses selected from a set of 45 stems. The retrievals examined were those in which the sole source of modularity with a metallic component was the head-stem taper interface between the Ti alloy taper stem and the ceramic head. To determine the surface chemistry and microstructures of both new and retrieved hip endoprostheses stem taper titanium alloy, scanning electron microscopy (SEM) was employed for morphological and microstructural analyses. At the same time, energy dispersive spectroscopy (EDS) was utilized for characterizing chemical element distribution, and electron backscattered diffraction (EBSD) was used for phase analysis. The micro-threated stem taper’s roughness for different manufacturers was investigated using an optical profilometer. Standard roughness pa-rameters Ra (average surface roughness) and Rz (mean peak to valley height of the roughness pro-file) were used in this investigation.Additionally, profile depth and peak spacing for different samples were investigated. The surface roughness results indicate no significant difference in roughness associated with varying survivorship times, ranging from 3 to 239 months, and across different manufacturers. Electrochemical studies revealed no fretting corrosion in retrieved stem tapers (ceramic head) that prematurely failed due to aseptic loosening after 239 months, infection after 3 months, and low-grade infection after a 32-month lifetime. Therefore, three retrieved ta-pers and two new ones for comparison underwent potentiodynamic measurements in Hank’s so-lution to ascertain the corrosion rate of new and retrieved stem taper surfaces. The results show a low corrosion rate for both new and retrieved samples that failed prematurely due to aseptic loosening. However, the corrosion rate of infected and low-grade infected tapers was higher. In conclusion, our study aligns with existing literature, suggesting that the use of ceramic heads de-creases the problem of taper corrosion and subsequently reduces premature failures in total hip arthroplasty.

In this paper we study a class of impulsive delayed neural networks with parameter uncertainties and reaction-diffusion terms. Using the properties of M-matrices and some inequality techniques, some sufficient conditions are derived to guarantee the global exponential stability of the given system. The results obtained are presented by simple algebraic inequalities, which are certainly more concise than previous methods. Finally, the validity and usefulness of our results are illustrated by arithmetic examples.

The application of antimicrobials in aquaculture primarily aims to prevent and treat bacterial infections in fish. Inappropriate use of antimicrobials in fish farming may result in the emergence of zoonotic antibiotic-resistant bacteria and subsequent transmission of resistant strains to humans via food consumption. From recently, AMR emerged as a significant public health concern in the aquaculture ecosystem and fisheries. The aquatic environment serves as a potential reservoir for resistant bacteria, with aquaculture practices providing an ideal breeding ground for AMR due to the excessive use of antimicrobials to prevent and treat diseases. The mutual inter-connection of intensive fish farming systems with terrestrial environments, food processing industry and human population creates pathways for the transmission of resistant bacteria, exacerbating the problem further. One Health concept, which recognizes the interconnectedness of human, animal and environmental health, enables a holistic approach to address the challenges posed by AMR. By understanding the evolution of such approach, the future of aquaculture, being the important source of a global animal protein supply, can be safeguarded. Risk mitigation strategies for AMR should be based on One Health concept to contribute to sustainable aquaculture practices that protect human and animal health, ensure food safety and protection of environment.

Green synthesis of silver nanoparticles (AgNPs) using raw Whey has never been reported. Silver nanoparticle formation involves a reduction reaction of silver salt solution with Whey extract. Extract and metal salt concentrations, and temperature can control this reaction. In this work, incubation period, extract, AgNO3, and NaOH concentrations were used as the independent factors using central composite design under response surface methodology. The aim was to elucidate the influence these factors have on the measured UV-Vis absorption spectra fitted with a Voigt function, and to optimize the conditions for nanoparticle formation. The fitting parameters, peak wavelength (λ0), peak area (A), and Full Width at Half Maximum (FWHM), were the responses. Silver nanoparticle formation was only possible in an alkaline environment (pH 10). The peak wavelength and the FWHM are influenced mainly by extract and AgNO3 concentrations. In contrast, the peak area is influenced by a total of 33.54 % from the interaction terms of AgNO3 and extract concentrations with NaOH. Metallic AgNPs were formed for the following parameter ranges: a) Whey (0.4 – 1.6 % v/v), b) AgNO3 (0.15 – 0.6 mM), c) NaOH (10 – 50 mM), and d) Time (20 – 60 min). Silver oxide nanoparticles were also observed.

This study presents a reproducible and scalable method for synthesizing silica nanoparticles (SNPs) with controlled sizes below 200 nm, achieved by systematically varying three key reaction parameters: ammonium hydroxide concentration, water concentration, and temperature. SNPs with high monodispersity and controlled dimensions were produced by optimizing these factors. The results indicated a direct correlation between ammonium hydroxide concentration and particle size, while higher temperatures resulted in smaller particles with increased polydispersity. Water concentration also influenced particle size, with a quadratic relationship observed. This method provides a robust approach for tailoring SNP sizes, with significant implications for biomedical applications, particularly in drug delivery and diagnostics. Using eco-friendly solvents such as ethanol further enhances the sustainability and cost-effectiveness of the process.

This study aimed to identify whether gyrate atrophy of the choroid and retina (GACR) heterozygous individuals have possible clinical manifestations and to explore the potential pathogenic mechanism. In this retrospective study, we surveyed a two-generation pedigree of an individual diagnosed with GACR. Two family members underwent ophthalmological, hematologic, and genetic tests. An arginine-restricted diet with vitamin B6 supplementation was implemented; clinical assessments were repeated every 3 months during follow-up. Relative OAT mRNA expression was determined using real-time quantitative polymerase chain reaction. The 19-year-old compound heterozygous daughter (OAT: c.1186C>T; c.748C>T), had bilateral high myopia, posterior staphyloma, chorioretinal atrophy, macular abnormalities, and elevated hematologic ornithine. The 54-year-old heterozygous mother (OAT: c.1186C>T), presented with bilateral severe myopia, asymmetric posterior staphyloma, retina and choroidal capillary layer atrophy, retinal pigment epithelium abnormalities, and mildly elevated hematologic ornithine. Compared to normal individuals, the daughter and mother had 29% and 46% relative OAT mRNA expression, respectively (P<0.001). We believe that this is the first report of a carrier of one OAT variant allele with mild phenotypes, suggesting that family members should be aware of the possible involvement of autosomal recessive conditions. Additional data suggests nonsense mediated decay-initiated mRNA degradation may cause GACR.

In an effort to enhance the efficiency and safety of open-pit mines, this study explores the optimization of end slope road parameters and slope structures, specifically focusing on unmanned driving lanes.A significant aspect of the study is the development of a truck trajectory offset model, which considers the different reaction times between automated sensors and human drivers in adapting to environmental changes. To test these concepts, the study uses numerical simulations to confirm the stability of the proposed end slope designs. Using Victory West Mine No. 1 as a case study, the research determines the optimized width for unmanned driving lanes and the maximum angle for safe steepening of end slopes. The findings indicate that the optimized unmanned lane width for NTE240 mining dump trucks is 1743 mm, allowing for a 2-degree increase in the slope angle at the south end slope. This optimization leads to a steep mining stripping volume of 3.2735 million m³ and a coal output of 2.49628 million tons, maintaining a stripping ratio of 1.31m³/t. These results demonstrate that the unmanned driving road width optimization not only ensures slope safety but also significantly boosts the economic benefits of steep mining in open-pit mines.

Despite recent developments in monitoring and visualizing construction progress, the data exchange between construction jobsite and office lacks automation and real-time recording. To address this issue, a near real-time construction work inspection system called iVR is proposed; this system integrates 3D scanning, extended reality, and visual programming to visualize interactive onsite inspection for indoor activities and provide numeric data. iVR comprises five modules: iVR-location finder (finding laser scanner located in the construction site) iVR-scan (capture point cloud data of jobsite indoor activity), iVR-prepare (processes and convert 3D scan data into a 3D model), iVR-inspect (conduct immersive visual reality inspection in construction office), and iVR-feedback (visualize inspection feedback from jobsite using augmented reality). An experimental lab test is conducted to validate the applicability of iVR process; it successfully exchanges required information between construction jobsite and office in a specific time. This system is expected to assist Engineers and workers in quality assessment, progress assessments, and decision-making which can realize a productive and practical communication platform, unlike conventional monitoring or data capturing, processing, and storage methods, which involve storage, compatibility, and time-consumption issues.

As well known, the torque produced by a rotating motor generates an opposite and equal reaction torque in the machine casing that must be transmitted to the base. In many applications, especially when the reaction moment has high values, it is necessary to apply some constructive solutions, which in certain cases are difficult to implement. In this context, the need to reduce the reaction moment from drive motors is a challenging topic, which has not been completely exhausted. In this paper, the authors present an original concept of a device which uses the centrifugal force generated by some equidistantly placed weights on a chain drive, for reducing the reaction torque of the motor used for driving a rotating tool. The proposed system is capable to produce a supplementary torque which can be added to driving moment. Due to this fact, by using this system, the power of the driving motor can be decreased, with the consequence of reducing the reaction moment, that must be absorbed by the base.

Ice accumulation poses considerable challenges in transportation, notably in the domain of general aviation. The present study combines the strengths and limitations of conventional aircraft de-icing techniques with the emerging trend toward all-electric aircraft. The study aims to utilize laser-induced graphene (LIG) technology to create a multifunctional surface, seamlessly integrating hydrophobic properties with efficient electrical heating to mitigate surface icing effectively. We investigated the utilization of a 10.6 μm CO2 laser for direct writing on polyimide (PI), a widely-used insulating encapsulation material. From the thermomechanical perspective, our initial analysis using COMSOL Multiphysics software revealed that when the laser power P exceeds 5 W, the PI substrate experience ablative damage. The experimental results show that when P ≤ 5W, an increase in power has a positive impact on the quality, surface porosity, roughness reduction, line-spacing reduction, and water contact-angle enhancement of the graphene. Conversely, when P > 5 W, higher power negatively affects both the substrate and the graphene structure by inducing excessive ablation. However, it influences the graphene line height positively and is consistent with overall experimental-simulation congruence. Furthermore, the incorporation of high-quality graphene resulted in a surface that exhibited higher contact angles (CA > 120°), lower energy consumption, and higher heating efficiency compared to the use of traditional electrically heated materials for anti-icing applications. The potential applications of this one-step fabrication method extend across various industries, particularly aviation, marine engineering, and other ice-prone domains. Moreover, the method has extensive prospects for addressing pivotal challenges associated with ice formation and serves an innovative and efficient anti-icing technology.

Hydrogen is now recognized as the primary alternative to fossil fuels due to its renewable, safe, high energy density and environmentally friendly properties. Efficient hydrogen production through water splitting has laid the foundation for sustainable energy technologies. However, when hydrogen production is scaled up to industrial levels, operating at high current densities introduces unique challenges. It is necessary to design advanced electrocatalysts for hydrogen evolution reaction (HER) under high current densities. This review will briefly introduce chal-lenges posed by high current densities on electrocatalyst, including catalystic activity, mass dif-fusion and catalyst stability. In an attempt to address these issues, various electrocatalyst design strategies are summarized in detail. In the end, our insights into future challenges for efficient large-scale industrial hydrogen production from water splitting are presented. This review is expected to guide the rational design of efficient high current density water electrolysis electro-catalysts and promote the research progress of sustainable energy.

The esterification of propylene glycol methanol (PM) and acetic acid (AA) is an important reaction for the production of propylene glycol methyl ether acetate (PMA). Herein, we used macroporous ion exchange resin Amberlyst-35 as a catalyst to explore the effects of reaction conditions on the reaction rate and equilibrium yield of PMA. Under the optimized conditions of reaction temperature of 353 K, initial reactant PM/AA molar ratio of 1:3, and catalyst loading of 10 wt%, PMA equilibrium yield reached 78%, which is the highest equilibrium yield so far. The reaction equilibrium constants and activity coefficients were estimated to obtain reaction thermodynamic properties, indicating the exothermicity of the reaction. Furthermore, Pseudo-homogeneous (PH), Eley-Rideal (ER), and Langmuir-Hinshelwood-Hogen-Watson (LHHW) kinetic models were fitted based on experimental reaction kinetic data. The results demonstrate that the LHHW model is the most consistent with experimental data, indicating surface reaction controlled process and exhibiting an apparent activation energy of 62.0 kJ/mol. This work represents a valuable example of calculating the reaction thermodynamic and kinetics, which are particularly essential for promising industrial reactor design.

The iron roughneck is an automated equipment utilized for the connection and removal of drilling tools. This paper presents the design of an integrated iron roughneck, providing a detailed introduction to its clamp body structure, along with an analysis of its structural characteristics and performance requirements. The study delves into the integration mode and working characteristics of the clamping mechanism and spin buckle mechanism for the integrated upper clamp body structure of the iron roughneck. Additionally, this paper conducts an in-depth theoretical study on the spin buckle mechanism. Firstly, it analyzes the actual working condition of the spin buckle roller from two perspectives: contact theory and rolling friction theory, determining the structural form of the spin buckle roller. Secondly, it investigates the relative displacement between the spin buckle mechanism and the drilling tool, proposing a design method for the floating device mounted on the spin buckle roller and establishing the kinematic equation of the spin buckle roller under the influence of the floating device. Furthermore, the kinematic equations of the spin buckle roller under the influence of the floating device are established. Finally, a dynamics simulation experiment is performed to simulate the working process of the spin buckle mechanism under actual working conditions, analyzing the dynamics and kinematics of the spin buckle mechanism and obtaining the relevant parameter curves of the spin buckle mechanism and drilling tools. Through data comparison and analysis, the correctness of the theoretical analysis results and the rationality of the performance and structure of the spin buckle mechanism are verified.

Rift Valley fever (RVF) is a mosquito-borne zoonotic viral disease that infects both human and animals. This is a descriptive study summarizes investigation and response to RVF outbreak, using surveillance data. A RVF outbreak occurred in Berber locality in northern Sudan. We identified 246 cases of RVF including seven deaths among humans, 119 deaths and 82 abortions among Livestock. Our entomological surveillance confirmed the presence of Anopheles arabiensis, An. stephensi, Aedes aegypti, Ae. vexans, Culex pipiens, Cx. Quinquefasciatus, and Cx. theileri in the area during the outbreak. In a comparison with another outbreak of Rift Valley fever in nearby area while ago, a multisectoral One Health response strategy has resulted in strengthening the health system through re-innovating health facilities and centres and training about 200 healthcare and emergency responders. Additionally, it reduced cases and fatalities among humans by 78% and 63%, respectively, and loss in livestock due to deaths and/or abortions by 82%. The added-value of implementing One Health strategy was saving more lives and resources, while strengthening the health system. We recommend the systematic institutionalization of One Health strategy in the country as a core part of the national prevention and control strategy for zoonotic diseases epidemics and pandemics.

Ammonia can be considered a relevant compound in the future energy sector, playing a significant role as an energy carrier, storage, or carbon-free fuel. However, the production of this molecule has a high energy demand, and the use of natural gas, which is not free of controversy due to the accidental leakage into the atmosphere produced during extraction and the fact that it is a non-renewable source, contributes to increasing greenhouse gas emissions. Reducing the process’s energy demand and carbon footprint will be essential to making ammonia a clear alternative for a carbon-free economy. Given the vast experience in ammonia production and handling, this gas seems to be the logical step forward in the evolution of the energy sector. However, the current uncertainty in the global market requires cautiousness in decision-making. Several factors may impact economic growth and human welfare, thus needing a careful assessment before taking any transcendental decisions that could affect worldwide energy prices and raw material availability.

The regulatory approvals of tumor agnostic therapies have led to reevaluation of the drug development process. Conventional models of drug development are histology-based. On the other hand, tumor agnostic drug development of a new drug (or combination) focuses on targeting a common genomic biomarker in multiple cancers, regardless of histology. Basket-like clinical trials with multiple cohorts allow clinicians to evaluate pan-cancer efficacy and toxicity. There are currently 8 tumor agnostic approvals granted by the Food and Drug Administration (FDA). This includes two immune checkpoint inhibitors, and 5 targeted therapy agents. Pembrolizumab is an anti-PD-1 antibody that was the first FDA approved tumor agnostic treatment for unresectable or metastatic microsatellite instability-high (MSI-H) or deficient mismatch repair (dMMR) solid tumors in 2017. It was later approved for tumor mutational burden-high (TMB-H) solid tumors, although the TMB cut-off used is still debated. Subsequently, in 2021, another anti-PD-1 antibody, Dostarlimab was also approved for dMMR solid tumors in the refractory setting. Patients with fusion-positive cancers are typically difficult to treat due to their rare prevalence and distribution. Gene rearrangements or fusions are present in a variety of tumors. neurotrophic tyrosine kinase (NTRK) fusions are present in a range of pediatric and adult solid tumors in varying frequency. Larotrectinib and entrectinib were approved for neurotrophic tyrosine kinase (NTRK) fusion-positive cancers. Similarly, selpercatinib was approved for Rearranged During Transfection (RET) fusion-positive solid tumors. FDA approved the first combination therapy of dabrafenib, a B-Raf Proto-Oncogene Serine/Threonine Kinase (BRAF) inhibitor, plus trametinib, a mitogen-activated protein kinase (MEK) inhibitor for patients 6 months or older with unresectable or metastatic tumors (except colorectal cancer) carrying BRAFV600E mutation. The most recent FDA tumor agnostic approval is of fam-trastuzumab deruxtecan-nxki (T-Dxd) for HER2-positive solid tumors. It is important to identify and expeditiously develop drugs that have the potential to provide clinical benefit across tumor types.

Imitation learning, also known as programming by demonstration, has been shown to be a promising paradigm for intuitive robot programming by non-expert users. However, the classical kinesthetic approach with physical hand guidance suffers from generalizability across different robot types and is impractical for demonstrating tasks with long horizons. Visual imitation learning enables the recording of multi-step tasks as a single continuous video, allowing non-experts to demonstrate tasks naturally. Existing approaches typically require a large amount of data to develop end-to-end deep learning models that map raw pixels to robot actions. This paper explores the application of visual imitation learning from one-shot demonstration, significantly reducing the data requirements and simplifying the programming process. To achieve this target, a framework is proposed to map hand trajectories to the robot end-effector, consisting of four essential components: hand detection; object detection; segmentation of the trajectories into elemental skills; and learning the skills. Methods are developed for each component and evaluated on recorded videos to demonstrate the effectiveness of the proposed framework.

The organic material present at the same depth in the reservoir has the potential for conversion, as indicated by analyses conducted before and after combustion in the development of heavy oil. This paper examines the oxidation and pyrolysis reaction pathways of hydrocarbons, specifically benzaldehyde (C₇H₆O) and naphthalene (C₁₀H₈), before and after combustion using molecular dynamics simulations. The primary products formed under various temperature conditions include H₂O, HO₂, CO, and CO₂. The discussion includes the number of molecules, such as HO and H, as well as their temperature variations. The activating group functions as an electron donor, while the inactivating group serves as an electron acceptor. The oxidation and pyrolysis reactions of naphthalene and the synthesis pathway of benzaldehyde are also explored. The C-C dissociation pathway in the early stages of combustion and the process of C-C bond synthesis in the later stages of the reactions are investigated through dynamic simulations at different temperatures: 3000 K, 3500 K, and 4000 K, with a particular focus on the reaction network at 4000 K. The application of the molecular reaction dynamics method to heavy oil combustion research is the primary objective of this work. This study aims to provide a novel approach to investigating hydrocarbon conversion at high temperatures and offers recommendations for enhanced oil recovery.

The relationship between tissue effects, intensity (I), and voltage (V) of a high-frequency alternative current seems well known. However, the translation of the settings of the electrosurgical unit and their use during surgery seems not to be unanimously understood by all surgeons. This results in many variations of surgical technique and plenty of specific questions asked during live surgery. Above 200 V, the heat of the sparks results in the explosion of superficial cells and a cutting effect. With higher voltages, the associated coagulation is increasing. Voltage and amount of energy (Watt=I*V) are independent since a similar amount of energy can be obtained with a continuous current or an intermittent current half the time and a double voltage. Below 200 V, tissue is heated until the steam from boiling tissue stops the current. Therefore, slower heating with less energy or a larger contact area permits deeper coagulation. The maximal output (W) of the electrosurgical unit results in versatility of use besides being a safety measure. The current intensity increases with the area of contact. Therefore, when I*V exceeds the preset output, V has to drop. A limited maximal output thus permits using the same instrument for non-contact cutting with >200V and sparks and coagulation when the contact area is much larger. In conclusion, the tissue effects of electrosurgery vary with the device’s voltage setting (often indicated as force) and the maximal output. The sur-geon’s choice to cut or coagulate by changing the contact area adds versatility.

Plant proteins being considered to become the most important protein source of the future, they must be able to replace the animal-derived proteins currently in use as technofunctional food ingredients. This poses challenges because plant proteins are oftentimes storage proteins with a high molecular weight and low water solubility. One promising approach to overcome these limitations is the glycation of plant proteins. The covalent bonding between the proteins and different carbohydrates created via the initial stage of the Maillard reaction can improve the technofunctional characteristics of these proteins without the involvement of potentially toxic chemicals. However, compared to studies with animal-derived proteins, glycation studies on plant proteins are currently still underrepresented in literature. This review provides an overview of the existing studies on the glycation of the major groups of plant proteins with different carbohydrates using different preparation methods. Emphasis is put on the reaction conditions used for glycation as well as the modifications to physicochemical properties and technofunctionality. Different applications of these glycated plant proteins in emulsions, foams, films, and encapsulation systems are introduced. Another focus lies on the reaction chemistry of the Maillard reaction and ways to harness it for controlled glycation and to limit the formation of undesired advanced glycation products. Finally, challenges related to the controlled glycation of plant proteins to improve their properties are discussed.

Motivated by diffraction experiments on the $\left(2\sqrt{3}\times \sqrt{3}\right)\mathrm{R}{30}^{\circ }$ reconstructed Si(111) due to deposition of rare earth elements (Dy, Tb) and silicide formation we analyse the splitting and non-splitting of superstructure spots. For this purpose, we model diffraction patterns for one dimensional structures generated by the binary surface technique and use supercell models to keep the analysis simple. Diffraction pattern are calculated in the framework of the kinematical diffraction theory and they are analyzed as a function of the domains and domain boundaries. Basic properties of the diffraction pattern are analyzed for model systems of a two-fold and a three-fold periodicity. The rules derived from these calculations are applied to the "real-world" system of Si(111)-($\left(2\sqrt{3}\times \sqrt{3}\right)\mathrm{R}{30}^{\circ }$)-RESi$2_{}$ (RE = Dy or Tb). Depending on the combination of domains and domain boundaries of different types a plethora of different features are observed in the diffraction patterns. These are analyzed to determine the sizes of both domain boundaries and domains from experimentally observed splitting of specific superstructure spots.

This study aimed to evaluate the effects of Blazepod technology when incorporated with various training regimens on the essential elements of physical fitness in volleyball, such as agility, speed, visual response time, and vertical leap. Thirty-six participants (age :17.33±0.48 y, height: 183.78±6.34 cm, weight: 77.14±5.16 kg) were in-volved in this study. In randomized design, three equal groups with two experimental groups and one control group were involved in the study over a period of six weeks: (GE1) used Blazepod technology to workout at a low level; (GE2) used Blazepod technology to workout at a higher intensity; (CG) did not employ Blazepod technology, but it adhered to the same fundamental training curriculum. We conducted agility, speed, reaction time, and vertical jump tests before, midway and after the study to determine optimal training volume, intensity, and frequency. A significant main effect of time (P0.01), and time×group interaction (P>0.001) were found for all tests. Post hoc test showed that the two experimental groups gadget significantly improved in all performance variables (P

The goal is the optimal synthesis of the parameters of the control law for a nonlinear satellite attitude control system under constraints related to the saturation effect of reaction wheels. The maximum stability degree of the control system is considered as a criterion for the optimality of the parameters of the control law, and the absolute values of the control torques and angular velocities of the reaction wheels, achievable within the limits of the physical characteristics of the drives, are considered as constraints. The solution to the optimal synthesis problem is based on the transformation of the nonlinear control system model into a linear model, within the framework of the problem of global asymptotic stability of the control system is also guaranteed. The problem is decomposed into a subproblems of obtaining the optimal transient process shape in the control system and considering the constraints. A method of synthesizing the optimal transient process shape based on the criterion of maximum stability degree had been developed. An analytical method of determining the optimal values of the control law parameters, based on decomposing the normalized characteristic polynomial in the linear model into three identical factors had been proposed. A method with regards to the constraints of the control torque and angular speed of the reaction wheels, based on transitioning from relative to real time is developed. An algorithm for calculation of the transition scale from relative to real time, ensuring the fulfillment of all constraints in the optimal synthesis problem, is proposed. An example demonstrating the efficiency and simplicity of the proposed methods and algorithm for targeted selection of technical characteristics of the control system, considering the maximum absolute values of angular speeds and control torques of the reaction wheels, is provided.

This article aims to analyze the relationship between non-obstructive coronary artery disease (NOCAD) and atrial fibrillation (AF), exploring the underlying pathophysiological mechanisms and implications for clinical management. NOCAD and AF are prevalent cardiovascular conditions that often coexist, yet their interrelation is not well understood. NOCAD, characterized by the presence of atherosclerotic plaques without significant luminal stenosis, can lead to ischemic necrosis of cardiomyocytes and their replacement with fibrous tissue, in this way sustaining the focal ectopic activity in atrial myocardium. Atrial fibrillation, on the other hand, is the most common sustained cardiac arrhythmia, associated with an increased risk of stroke and heart failure, which may accelerate atherosclerosis and may increase oxygen consumption in the myocardium, creating a mismatch between supply and demand, thus promoting the development or worsening of coronary ischemia. Therefore, NOCAD and AF seems to be a complex Interplay with one begets another.

The socio-economic benefits of globalization cannot be overemphasized. However, the global spread of infectious diseases has so followed a parallel course. The recent wave of pandemics with emerging new diseases has shown that no part of the world is immune from the spread of infectious diseases. COVID-19 like previous pandemics has exposed inadequacies of our healthcare systems and global capacity for prevention, early detection, and response in pandemic outbreaks. Given the highly interconnected global economy and the high potential for passim spread of infections, every nation must not only come up with concerted efforts to prevent and better prepare for pandemics, international solidarity and engagements will also be critical to ensure a long-lasting and sustainable solution. We are only as strong as our weakest health system, global support to strengthen all health systems around the world is the most effective way to be pandemic – ready. ‘All for one and one for all’.

Lung neuroendocrine tumors (LNETs) and gastroenteropancreatic neuroendocrine tumors (GEPNETs) are two distinct types of neuroendocrine tumors (NETs) that have traditionally been treated as a single entity despite originating from different sources. Although they share certain phenotypic characteristics and the expression of neuroendocrine markers, they exhibit differences in their microenvironment, molecular mutations, and responses to various therapeutic regimens. Recent research has explored the genetic alterations in these tumors, revealing dissimilarities in the frequently mutated genes, role of EGFR in carcinogenesis, presence of transcription factors, and immunogenicity of the tumor and its microenvironment. Spread Through Air Spaces (STAS), a phenomenon unique to lung carcinomas, appears to play a crucial role in LNET prognosis. These distinctions are also evident in the cascade response of lung and GI tract neuroendocrine tumors to somatostatin analogs, Peptide Receptor Radionuclide Therapy (PRRT), chemotherapy, and immunotherapy. Identifying similarities and differences between the two groups may im-prove our understanding of the underlying mechanisms and facilitate the development of more effective treatment strategies.

Peripheral nerve injuries (PNI) can have several etiologies, such as trauma and iatrogenic interventions that can lead to the loss of structure and/or function impairment. These changes can cause a partial or complete loss of motor and sensory functions, physical disability, and neuropathic pain, what in turn can affect the quality of life. For those reasons, PNI is a major public health concern. This review aims to revisit the concepts associated with the PNI. First, the anatomy of the peripheral nerve is detailed to explain the different types of injury. Then, some of the available therapeutic strategies are explained, including surgical methods, pharmacological therapies, and the use of cell-based therapies alone or in combination with biomaterials in the form of tube guides. Nevertheless, even with the various available treatments, it is difficult to achieve a perfect outcome with complete functional recovery. This review aims to explain the urge for new approaches and to understand the methods to evaluate nerve regeneration in a One Health perspective. In vitro models followed by in vivo models are very important to be able to translate the achievements to human medicine.

Breast cancer (BC) is the most common invasive neoplasm and affects many women of working age. The return to work (RTW) of female survivors (BCSs) is associated with a better quality of life and longer survival. A tailored intervention to promote RTW was launched in 2022. A year later, the women were contacted to find out if RTW had occurred regularly and what their health conditions were compared to baseline. BCSs reported excessive fatigue, poor sleep quality, anxiety, depression and reduced work ability; these parameters had not improved significantly compared to baseline. Thematic analysis of the interviews confirmed the presence of personal, company and societal factors that could hinder or favor RTW. The interviews demonstrated that, even in an economically developed country that has provided numerous benefits for BCSs, protection is not always effective. Personalized intervention seems necessary to complete the process of reintegrating BCSs into their future working careers.

The COVID-19 pandemic caused by the novel severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) virus has exposed the vulnerabilities and unpreparedness of the global healthcare system in dealing with emerging zoonoses. In the past two decades, coronaviruses (CoV) have been responsible for three major viral outbreaks, and the likelihood of future outbreaks caused by these viruses is high and nearly inevitable. Therefore, effective prophylactic universal vaccines targeting multiple circulating and emerging coronavirus strains are warranted. This study utilized an immunoinformatic approach to identify evolutionarily conserved CD4+ (HTL) and CD8+ (CTL) T cells, and B-cell epitopes in the coronaviral spike (S) glycoprotein. A total of 132 epitopes were identified, with the majority of them found conserved in the bat CoV, pangolins CoV, endemic coronaviruses, SARS-CoV-2, and Middle East respiratory syndrome coronavirus (MERS-CoV). Their peptide sequences were then aligned and assembled to identify the overlapping regions. Eventually, two major peptide assemblies were derived based on their promising immune-stimulating properties. In this light, they can serve as lead candidates for universal coronavirus vaccine development, particularly in the search for pan-coronavirus multi-epitope universal vaccines that can confer protection against current and novel coronaviruses.

A sustainable green one pot procedure for the synthesis of dihydropyrimidinones (DHPMs) derivatives by a three-component reaction of β-ketoester derivatives, aldehyde and urea or thiourea over the alkali-treated H-ZSM-5 zeolite under ball-milling has been developed. The product was isolated by simple washing of the crude reaction residue with ethyl acetate followed by evaporation of solvent. The hierachical zeolite catalyst (MFI27_6) showed high yield (86–96%) of dihydropyrimidinones (DHPMs), in very short time (10-30 min). The catalyst is recycled for subsequent reactions in four runs without appreciable loss of activity and high yields of products provide efficient protocol for Biginelli reactions.

Stage IV grade C localized periodontitis (pre-puberal localized aggressive periodontitis/LPP), an extremely rare form of periodontal disease, occurs in otherwise healthy individuals (no signs of dental plaque/calculus) due a hyper-aggressive auto-immune response to high periodontopathic bacteria levels. Methods: A 4-year-old Caucasian girl with unusual high mobility of temporary lower left canine and localized gingival inflammation was misrecognized by multiple clinicians (initially diagnosed with hypophosphatasia, genetic and metabolic disorders, all turning negative), over a period of 4-6 month, despite initial radiographs showing clear pathognomonic signs. LPP diagnostic was made by the last clinician, but by now the tooth was lost. Similar inflammation signs appeared around the lower temporary right canine. X-ray examination showed similar bone and periodontal loss as previously seen, while periodontopathic bacteria tested highly positive. The patient received both mechanical cleaning and ten days systemic antibiotic treatment (Augmentin and Metronidazole). Results: Two months after, inflammation signs disappeared, with periodontal regeneration radiologically present, and only small periodontopathic bacteria precursors concentrations. Conclusions: Despite initial periodontal loss, an adequate treatment can keep under control an LPP disease. Moreover, bone and periodontal regeneration appears if periodontopathic bacteria scores are kept lower, showing the importance of fast adequate diagnostic and treatment.

Group A rotaviruses (RVA) have been identified as the leading cause of neonatal calf diarrhea (NCD) In Yunnan, China, despite the limited documentation on this issue within the country. Given the significant impact on animal health and welfare, further attention is warranted to comprehend the prevalence and epidemiology of this disease. In this study, we isolated RVA strains from NCD clinical samples to support RVA epidemic study and further disease control in Yunnan. Material and Methods: Ten fecal samples were obtained from calves with a single episode of neonate calf diarrhea from a farmer during a severe NCD outbreak. For the diagnosis of Group A rotavirus (RVA) infection, fecal reverse transcription-polymerase chain reaction (RT-PCR) was employed as the primary method. Subsequently, RVA isolation was conducted on MA104 cells, with inoculates being pretreated with trypsin TPCK to enhance viral infectivity. The isolated RVA strain was further confirmed through RT-PCR and immunofluorescence assay. Results: RVA virus was isolated from clinical samples following six passages depended on trypsin treatment of inoculates. The sign of CPE detected consisted of increased cell granularity, obscure cell boundaries, cell rounding, and eventual degeneration and detachment of cells. Analysis of sequencing revealed that field isolates was of group A serotype. Phylogenetic analysis based on the ORF sequences of the VP4 and VP7 sequences segments indicated that the isolate was classified as the P[1] genotype. VP4 gene of strain YN-1 shares 75.2%-99.7% nucleotide identity of and 81.6%–99.7% amino acid identity with the complete VP4 sequences of the P[1]. The complete VP7 gene of YN-1 is 981 nucleotide long and encode 326 amino acids. The RotaC v2.0 analysis classified the sequence as the G8 genotype. The VP7 gene of strain YN-1 shares 88.5%-97.7% nucleotide identity and 94.2%-99.1% amino acid identity. Conclusion: This is the first study in China which reports the circulation of Group A NCD on cattle farms in the field. Our study constitutes a crucial and a necessary step allowing preventive and veterinary medicine to support RVA disease controls in Yunnan province, China.

(1)Background: Fascioliasis is considered a neglected tropical disease affecting an estimated 17 million people in more than 70 countries worldwide. The highest prevalence of human fascioliasis is found in regions where livestock farming and consumption of raw or undercooked freshwater plants are common, such as parts of Africa, Asia, Europe, and Latin America. It is responsible for over 90,000 disability-adjusted years of life due to associated abdominal complications. We conducted a study to investigate the prevalence of human fascioliasis through a systematic review and meta-analysis of all available literature in Sun-Saharan Africa.(2). Methods: We screened a total of 126 publications using pubmed online search engine databases; Web of Science and CAB for articles published within a 20-year period between 2000 and 2022. We used a comprehensive search method using a combination of terms, parasite and disease names. The initial search resulted in a screening of articles by title, abstracts and full texts. The relevant information on the prevalence of human fascioliasis in Africa was extracted. Of the 126 publications, 33 articles were selected for meta-analysis. The essential information required was extracted from these documents and determined through statistical analysis in Microsoft Excel for calculating the prevalence of human fascioliasis in sub-Saharan Africa. The variance of each study was assessed using a bimodal distribution and heterogeneity assessment using a I2 index. Analysis was performed using random effects models.(3)Results: A total of 271 articles were searched through the database search and 33 articles were eligible studies that provided qualitative information on the prevalence of human fascioliasis in Africa. These make up 12.17% (n=33). The pooled prevalence estimates for human fascioliasis are 0.032% (IVhet PPE: 0.032% (95%CI 1.4-6.53). The highest prevalence rate was observed in Egypt with a prevalence of 100%. The prevalence of human fascioliasis is very high in some sub-Saharan countries, partly due to neglect of diagnostics, demonstrating the bias of available information for decision-making in human fascioliasis across Africa, given the spatial presence, scarcity and incompleteness are region.(4)Conclusions: The prevalence of Human fascioliasis is very high in some Sub-Saharan Countries partly due to neglect in diagnostics. This presents how highly focal with spatial occurrences, scarcity and patchy the available information for decision making is on Human fascioliasis across the Sub-Saharan African region.

This investigation is part of a topical situation where wireless equipment is gradually being used for energy transfer, particularly for autonomous systems and the use of decarbonized en-ergies. A characteristic example of decarbonized autonomous use is linked to the substitution of thermal engine vehicles by electric vehicles (EVs) equipped with energy storage batteries. This response was considered in an ecological context of reducing air pollution and defending plane-tary biodiversity, which are currently vital. These EVs ultimately operate thanks to the wireless charging of their batteries when stationary or running. By changing long-established means of transport that have become a threat to biodiversity, it is necessary to ensure that innovative re-placement solutions protect this biodiversity. In addition, the construction of wireless power transfer (WPT) battery chargers for these EVs must offer an optimal ecology of clean energy saving. In such a context, the two concepts of One Health (OH) and Responsible Attitude (RA) will find their place in the design and control of WPT tools in EVs. This contribution aims to il-lustrate and analyze the roles of the green and non-wasteful OH and RA approaches in the de-sign and control of WPT embedded in EVs for the smart city (SC) environment. In the paper, WPT tools are first introduced. The design and control of EV battery charging tools are then examined. The biological effects on living tissues due to the electromagnetic field (EMF) radia-tion of WPT are analyzed. The phenomena and equations governing the design of WPT and the effects of EMF radiation are then exposed. The OH and RA approaches in the SC context are af-terward analyzed. The protection against the unsafe effects of WPT tools in the SC environment is consequently explored. The analyses followed in the paper are supported by examples of lit-erature.

Separase is a key cysteine protease to separate sister chromatids through digestion of cohesion ring that inhibits chromosome segregation as trigger of metaphase–anaphase transition in eukaryotes and highly regulated its activity by binding with securin and cyclinB-CDK1 complex. Those bindings prevent proteolytic activity of separase until the onset of anaphase. Chromosome missegregation and aneuploidy are frequently observed in malignancies. However, there are some difficulties for biochemical examinations due to instability of separase in vitro and a few spatiotemporal resolution approaches monitoring live separase activity throughout mitotic processes. Here we have developed FRET-based molecular sensors including GFP variants with separase cleavable sequences as donor and covalently attached fluorescent dye as acceptor molecules applicable to conventional live cell imaging and flow cytometric analysis because of efficient live cell uptake. We investigated performance of equivalent molecular sensors localized or not localized inside nucleus under cell cycle control using flow cytometry. Synchronized cell cycle progression rendered significant separase activity detections in both molecular sensors. We obtained consistent outcomes with localized molecular sensor introduction and cell cycle control by fluorescent microscopic observations. We thus established live cell separase activity monitoring systems specifically or statistically that could lead to elucidate separase properties in detail.

The microbioma is presently one of the hottest areas of scientific and medical research and exerts a marked influence on the host during homeostasis and disease. Fermented foods arise in the human relationship to the microbial environment. Further to the traditionally recognized effects of fermented foods and beverages on the digestive health and well-being there is now strong evidence on their general health benefits, namely the significance on the gut microbiota and brain functionality. We highlight the possibilities in this field, how little is still known, and call for a convergence of interdisciplinary research fields of One Health microbe-nutrition with fermented foods and gut-brain research. A consequence of civilisation, changes in present-day society in diets with more sugar, fat and salt, habits and lifestyle, contributes to the likelihood of an inflammatory microbiome, particularly the global epidemics of obesity and mental health. Although two recent papers claim that probiotics perturb rather than aid in microbiota recovery back to baseline after antibiotic administration in humans, consuming fermented foods has shown to reduce inflammation so improve gut health and the proper function of the body’s immune system.

We describe an interesting case report about a patient with hemophilia A with severe chronic elbow arthropathy who underwent multiple surgical because of his condition. We collected all the clinical and imaging findings, and we compared the decision-making flow chart and the surgery performed with the most recent indications, treatments and complications reported in the literature. The aim of this case report is to show how usually the hemophilic patient even if young usually comes to our attention from the beginning with complex and advance musculoskeletal disease. Elbow hemophilic arthropathy is a complex disease and the management in these patients could be more difficult than others because of the higher risk of complications rate after all surgical procedures, for this reason it’s very important to treat these patients in hub centers with expertise in well-coordinated multidisciplinary teams. The path from diagnosis to surgical treatment of hemophilic elbow arthropathy can be a risky one, as it happened in this case.

The giant octopus caught off the east coast of Korea is an important fishery resource with the largest haul and is mostly caught using net pots. While giant octopus pots have different shapes, drum, rectangular, and cylinder pots are mostly used. However, these pots have not been thoroughly evaluated. Here, we evaluated the fishing performance of three giant octopus pots, their fluid resistance, and underwater movement. Six sea trials were conducted near the Hupo region in Gyeongsangbuk-do. In total, 163 individuals (62,724 g), 190 individuals (49,913 g), and 154 individuals (52,364 g) were caught using drum, rectangular, and cylinder pots, respectively. Drum pots showed significant differences in the amount of catch by weight (ANOVA test, p<0.05). Moreover, the percentage of minimum conservation size was the lowest in cylinder pots (6.5%). Drum pots showed the highest stability in the underwater stability test, while underwater fluid resistance at 2.5 kt fluid speed was in the following order: drum pots (7.66 kgf) > rectangular pots (7.16 kgf) > cylinder pots (7.04 kgf). Therefore, drum pots showed excellent fishing performance. This study provides foundational data for developing managing systems for giant octopus resources and establishing the extent of fishing gear usage.

Establishment of diagnostic methods with low detection limits plays a critical role in the maintenance of early diagnosis, prevention of serious neurological complications, and control of the spread of ZIKA. In this study, we established the micro-droplet digital polymerase chain reaction (ddPCR) and real-time fluorescent quantification PCR (qPCR) protocols for the detection of Zika virus based on the NS5 gene. For the Zika standard plasmid, the standard curve of R² was 0.999, and the amplification efficiency was 92.203%, as determined by qPCR. Both ddPCR and qPCR were positive for cell culture of Zika nucleic acid.The minimum detection limit of ddPCR is 1–2 times lower than qPCR. Moreover, all tests of Dengue virus (1–4 serotypes) were negative in cell culture. Overall, these results suggested than ddPCR may have a lower limit of detection than qPCR.

Preprints is delighted to have passed the milestone of one thousand preprints online. This is a significant step for the platform, which was launched in May last year with the objective of speeding up the process of communicating research across all disciplines. We are proud to be the first preprint server to cover all disciplines.

Background/Objectives:The first attempts of posterior lumbar interbody fusion can be traced back to the 1940s, where their performance was marked by animosity due to high rates of failure. Nowadays, the use of interbody fusion involves a much more complicated consideration of factors such as global alignment, disc height, fusion rates, and operative risk, all combined at once.Our study aims to examine all these effects using Flarehawk 9 as a means of interbody fusion.Materials and methods: A total of 58 patients underwent open posterior lumbar surgery using Flarehawk 9 between September 2021 and February 2023 with a mean follow up of 1 year.The mean age was 59.8 years old ( range between 33 and 79 years old), 36 of them are males while 22 of them are females. The diagnostic groups included spinal canal stenosis (n=40), failed back surgery syndrome-revision surgery (n=5),spondylolisthesis with slip percentage 25% (n=4),recurrent herniated disc (n=7) and adjacent segment disease (n=2). Results: The majority of patients demonstrated remarkable improvement based on ODI scores.The rate of union varied based on the fused levels and whether the patients had previous surgery or not.The amount of lordosis postoperatively is increased by 2±0.4 degrees.Conclusions: Even though anterior approaches become more and more popular and advanced nowadays, posterior fusion with interbody cage still remains a safe and effective method to treat various spine surgical pathologies with optimal results.

Non-polio enteroviruses (NPEVs), namely coxsackieviruses (CV), echoviruses (E), enteroviruses (EV), and rhinoviruses (RV), are responsible for a wide variety of illnesses. Some infections can progress to life-threatening complications in children or immunocompromised patients. To date, no treatments have been approved. Several molecules have been evaluated through clinical trials without success. To overcome these failures, the multi-target directed ligand (MTDL) strategy can be applied to tackle enterovirus infections. This work analyzes clinical trials to highlight the best candidates and develops filters to apply to a selection for MTDL synthesis. We explicitly stated the methods used to answer the question: Which solution can fight NPEVs effectively? We note the originality and relevance of this proposal in relation to the state of the art in the enterovirus-inhibitors field. Several combinations are possible to broaden the antiviral spectrum and potency. We discuss data related to the virus and data related to each LEAD compound identified. Overall, this study proposes a perspective on different strategies to overcome issues identified in clinical trials and evaluate the “MTDL” potential to improve the efficiency of drugs synergistically, broaden the targeted, and reduce the adverse effects and drug design cost as well as limit the opportunity of drug-resistant viruses.

Noninvasive brain stimulation technique can be used for modulation of motor behaviors such as reaction time (RT). The main aim of this study was to investigate whether RT during a sequential visual isometric pinch task (SVIPT) can be affected by anodal transcranial direct current stimulation (a-tDCS) over three different stimulation sites such as dorsolateral prefrontal cortex (DLPFC), primary motor cortex (M1) or posterior parietal cortex (PPC). We also aimed to assess if stimulation of these cortical sites affect the transfer of learning during SVIPT. A total of 48 right-handed healthy participants were randomly assigned to one of the four a-tDCS groups: 1) left M1, 2) left DLPFC, 3) left PPC and 4) sham. A-tDCS was applied concurrent with SVIPT in which the participants were precisely controlled their forces to reach seven different target forces from 10 to 40% of maximum voluntary contraction (MVC) presenting on a computer screen with right dominant hand. Four test blocks were randomly performed at baseline and 15 min after the intervention including sequence and random blocks with either hand. Our results showed significant differences between a-tDCS groups on ratio RT in the sequence blocks of both the right trained (P = .041) and left untrained hands (P = .023) for target forces of 15% and 30 % of MVC, respectively. In sequence blocks, M1 showed significant elongation in ratio RT for the target force of 15% and 30 % MVC compared to PPC and Sham groups in the right hand. In sequence blocks with left hand, this negative effect were found between M1-DLPFC and M1-Sham groups. In random blocks, no significant differences were found among four groups at each target forces for the left hand while there were significant differences for 15% (P =. 04) and 40% MVC (P =. 035) in the right hand. Our findings suggest that three different stimulation sites (DLPFC, M1 or PPC) were differentially affected by a single session of a-tDCS at some target forces during SVIPT. The effects of a-tDCS on ratio RT were transferred in the left untrained hand for sequence blocks but not random blocks. Further research is needed to understand fundamental aspects of these main areas of the brain on temporal processing in a precision control task such as SVIPT.

The hetero Diels-Alder (HDA) reaction between the ambident heterodiene 3-methylene-2,4-chromandione (MCDO) and the non-symmetric methyl vinyl ether (MVE) is investigated within the Molecular Electron Density Theory (MEDT) at the B3LYP/6-311G(d,p) computational level. The aim of this study is to gain insight into the molecular mechanism and to elucidate the factors that control the selectivity found experimentally. DFT-based reactivity indices reveal that MCDO exhibits strong electrophilic character, while MVE displays a strong nucleophilic character. Meanwhile, Parr function explains the ortho regioselectivity of this HDA reaction. The highly polar nature of this HDA reaction, supported by the high global electron density transfer (GEDT) taking place at the transition state structures (TSs), accounts for the very low activation energy associated with the most favorable TS-4on. The ambident nature of MCDO allows the formation of two constitutional isomeric cycloadduct. In the case of MVE, the pseudocyclic selectivity is attained by a thermodynamic control. This polar HDA reaction displays an endo stereoselectivity and a complete ortho regioselectivity. A comparative Relative Interacting Atomic Energy (RIAE) analysis of the two diastereomeric TS-4on and TS-6on indicates a highly likeness between them, which explains the low pseudocyclic selectivity under kinetic control.

Density functional theory (DFT) calculations of hydrogen adsorption on titanium nitride had previously shown that hydrogen may adsorb on both titanium and nitrogen sites with a moderate adsorption energy. Further, the diffusion barrier was also found to be low. These findings may qualify TiN, a versatile multifunctional material with electronic conductivity, as electrode material for the hydrogen evolution reaction (HER). This was the main impetus of this work which aims to experimentally and theoretically investigate the electrocatalytic properties of TiN-layers that were processed on Ti substrate using reactive ion sputtering. The properties are discussed focusing on the role of oxygen defects introduced during the sputtering process on the HER. Based on DFT calculations, it is shown that these oxygen defects alter the electronic environment of the Ti atoms which entails a low hydrogen adsorption energy in the range of -0.1 eV; this leads to HER performances that match those of Pt-NPs in acidic media. When a few nanometr thick layer of Pd-NPs is sputtered on-top of the TiN-layer, the performance is drastically reduced. This is interpreted in terms of oxygen defects being scavenged by the Pd-NPs near the surface which is thought to reduce the hydrogen adsorption sites.

Our knowledge of electricity is based on two parallel lines of research: one focusing on ‘charge’, the other on ‘electron’. The distinction is blurred. The difficulty is that the fundamental nature of elementary charge is unknown. Here I present evidence that charge is a resting electron and electron is a moving charge – one physical entity two behavioural identities. That is, charge is nonrelativistic electron and electron is relativistic charge. Charges obey the laws of static electricity (electrostatics); electrons obey the laws of moving electricity (electrodynamics). Whether positive or negative, a charge is ejected from the atom at tremendous speed, losing the characteristics of ‘a charge’ and gaining those of ‘an electron’. I conclude that an atom, hence nature in general, contains an equal number of positive and negative electrons, recognised at rest as opposite charges. This solves the mystery of the electron-positron numerical asymmetry. It means that static positions and negatrons (charges) play equivalent roles as subatomic building blocks of matter, revealing a new atomic structure.

Catalyst material plays a pivotal role in the pharmaceutical industry process. Among them, Friedel-Craft acylation reaction is a well-known reaction to synthesis acetophenone derivatives. However, Friedel-Craft acylation mostly used acetyl chloride as starting material with Lewis acid as homogeneous catalyst, which is nonenvironmental friendly process. In this work, a simple and efficient Friedel-Craft acylation reaction is reported by using the palladium oxide doped on activated bentonite (PdOAB) as the heterogeneous catalyst. The PdOAB catalyst material was characterized with scanning electron microscopy-energy dispersive X-ray (SEM-EDX), nitrogen isotherm adsorption, Fourier transform infrared (FTIR), X-ray powder diffraction (XRD), and thermogravimetric-differential thermal analysis (TG-DTA). The acetophenone derivatives with R = -H, -Cl, -CH₃, -OCH₃, -OH and -NH₂ at para position were successfully synthesized from its corresponding aromatic compounds with glacial acetic acid in 86.6, 7.9, 91.7, 86.6, 82.7, and 78.9% yield, respectively. Therefore, a green method was established because the byproduct is water and the catalyst material can be recovered. Furthermore, the substituent (σ) constants were obtained by using Hammet equation, and the catalysis mechanism has been proposed.

Developing sustainable and renewable energy sources is critical as higher and higher global energy and environmental challenges arise. Hydrogen has the highest mass/energy density of any fuel and is considered one of the best sources of clean energy. Water splitting is regarded as one of the most promising solutions for hydrogen production on a large scale. Highly efficient, durable and cost-effective catalysts for hydrogen evolution reaction (HER) are critical in the realization of this goal. Among many materials proposed, graphene-based materials offer some unique properties for HER catalysis. In this review, we present recent progress on development of graphene-based electrocatalysts toward HER throughout the past few years.

This work demonstrates that a plasmid can function as an efficient biocatalyst in mediating the nitroaldol (Henry) reaction at high temperatures in ultrapure water. Compared with ssDNA, the plasmid displayed a remarkable catalytic efficiency (97% yield within 20 min). Aromatic aldehydes which bear strong or moderate electron-withdrawing groups reacted satisfactorily with nitromethane, which afforded the corresponding β-nitroalcohols in good yields within 2 h (up to 98%). By contrast, aliphatic and aromatic aldehydes with electron-donating groups did not react. Moreover, the yield significantly dropped when the size of the carbanion increased, and the yield was only 10% when nitropropane was used as the donor.

Mucosal healing (MH) is the main treatment target in ulcerative colitis and Crohn’s disease, and it is defined by a combination of complete endoscopic and histologic remission. Indeed, the complete resolution of mucosal inflammation should be confirmed at histology. Neutrophil infiltration represents the unique histological marker in discriminating the active vs quiescent phase of disease, also including crypt injuries (cryptitis and crypt abscesses), erosions and ulcerations. Basal plasmacytosis do not qualify by itself the remission in inflammatory bowel diseases (IBD), but it represents a diagnostic clue, mostly at onset. Several histological scoring systems have been developed to evaluate therapeutic efficacy, even though they often resulted tricky and subjective. Moreover, these scores listed a heterogeneous group of histological features as parameters. The recently proposed simplified histological score on MH was based on neutrophils and their distribution in the gut mucosa was also considered, aiming to provide a simple, time-sparing and reproducible tool to be applied to the routinary diagnostic practice. The artificial intelligence could be a promising tool both in evaluating and standardizing the histological assessment of disease activity in IBD. Moreover, novel molecules involved in the inflammatory dynamics in the gut could be employed in supporting the diagnostic practice in IBD.

New fluorinated pentaphene derivative has been obtained as a potential precursor for fluorinated polycyclic aromatic hydrocarbons. In this work 7,7-difluoropentaphen-6(7H)-one was prepared from 1,1-difluoroanthracen-2(1H)-one via Diels-Alder reaction with o-quinodimethane generated in situ from o-bis(dibromomethyl)benzene. The structure of newly synthesized compound was confirmed by 1H, 13C, 19F NMR, IR and UV/Vis spectroscopy as well as high-resolution mass spectrometry.

The traditional practice of harvesting and processing raw date palm sap is not only culturally significant but also an essential nutritional source in South Asia. Yet, the potential for bacterial or viral contamination from animals and environmental sources during its collection remains a real and insufficiently studied risk. Implementing improved food safety measures and collection techniques could mitigate the risk of these infections. Additionally, the adoption of advanced food analytical methods has the potential to identify pathogens and uncover the natural bacterial diversity of these products. The advancement of NGS technologies, particularly nanopore sequencing, offers rapid and highly mobile capabilities. In this study, we employed nanopore sequencing for bacterial metabarcoding of a set of raw date palm sap samples collected without protective coverage against animals in Bangladesh in 2021. We identified several bacterial species with importance in the natural fermentation of the product and demonstrated the feasibility of this NGS method in the surveillance of raw palm sap products. We revealed two fermentation directions dominated by either Leuconostoc species or Lactococcus species in these products at the first 6 hours from harvest along with opportunistic human pathogens in the background, represented with low abundance. Plant pathogens, bacteria with the potential for opportunistic human infections and the sequences of the Exiguobacterium genus were also described and their potential role is discussed.

It is unclear whether military shoes (combat boots and sports shoes) attenuate loading rate or affect force transfer during walking. Therefore, this study compared ground reaction forces (GRF) related to impact and force transfer between combat boots, military sports shoes and running shoes. Ten army recruits walked over a walkway with two force plates embedded. GRF were measured when walking barefoot (for data normalization) and with combat boots, military sports shoes and running shoes. Loading rate, first and second peak forces and push-off rate of force were computed along with temporal analysis of waveforms. Reduced loading rate was observed for the running shoe compared to the combat boot (p = 0.02 and d = 0.98) and to the military sports shoe (p = 0.04 and d = 0.92). The running shoe elicited a smaller second peak force than the combat boot (p < 0.01 and d = 0.83). Walking with military shoes and combat boots led to larger force transfer then running shoes potentially due to harder material used in midsole composition (i.e. styrene-butadiene rubber). These results could lead to a potentially larger risk of injuries while long duration walking in military shoes and boots compared to traditional running shoes.

Background: Nutritional status and oxidative stress have been implicated in the pathogenesis and persistence of long COVID, but data in patients undergoing hemodialysis (HD) are limited. The present study aimed to investigate the association between pre-infection nutritional status, oxidative stress, and one-year long COVID persistence in HD patients. Methods: This prospective observational cohort study enrolled 115 HD patients with confirmed COVID-19. Nutritional status was assessed using the Controlling Nutritional Status (CONUT) score twice: before infection and three months post-infection. Oxidative markers included malondialdehyde (MDAs), ceruloplasmin, transferrin, and sulfhydryl groups. The endpoint was one-year long COVID persistence. Results: Moderate pre-infection CONUT scores were associated with heightened severe undernutrition risk (p &lt; 0.0001), elevated MDAs (p &lt; 0.0001), and reduced ceruloplasmin levels (p = 0.0009) at three months post-COVID-19 compared to light CONUT scores. Pre-infection CONUT score independently predicted post-COVID oxidative damage [OR 2.3 (95%CI 1.2; 4.6), p &lt; 0.0001] and one-year long COVID persistence [HR 4.6 (95%CI 1.4; 9.9), p &lt; 0.0001], even after adjusting for potential confounders. Conclusion: Moderate pre-infection undernutrition in patients undergoing HD associated with increased post-COVID oxidative stress intensity and heightened risk of one-year long COVID persistence.

World Health Organization (WHO) has announced the monkeypox (MPX) epidemic a global public health emergency due to its re-emergence, remarkable increase in the number of MPX cases worldwide, and its potential spread. This paper introduces the symptoms, complications, and features of MPX; its transmission, diagnosis and testing, vaccines and treatment; MPX and sexually transmitted diseases, especially the human immunodeficiency virus (HIV); possible natural hosts or reservoirs of the monkeypox virus (MPXV). A useful tool for MPX and surgical safety recommendations are presented. The challenges in fighting the MPX epidemic, One Health strategy, and future research are discussed.

This work is driven by a practical question, corrections of Artificial Intelligence (AI) errors. Systematic re-training of a large AI system is hardly possible. To solve this problem, special external devices, correctors, are developed. They should provide quick and non-iterative system fix without modification of a legacy AI system. A common universal part of the AI corrector is a classifier that should separate undesired and erroneous behavior from normal operation. Training of such classifiers is a grand challenge at the heart of the one- and few-shot learning methods. Effectiveness of one- and few-short methods is based on either significant dimensionality reductions or the blessing of dimensionality effects. Stochastic separability is a blessing of dimensionality phenomenon that allows one-and few-shot error correction: in high-dimensional datasets under broad assumptions each point can be separated from the rest of the set by simple and robust linear discriminant. The hierarchical structure of data universe is introduced where each data cluster has a granular internal structure, etc. New stochastic separation theorems for the data distributions with fine-grained structure are formulated and proved. Separation theorems in infinite-dimensional limits are proven under assumptions of compact embedding of patterns into data space. New multi-correctors of AI systems are presented and illustrated with examples of predicting errors and learning new classes of objects by a deep convolutional neural network.

Since the advent of the OBORI, it was subjected to numerous studies. However, most previous studies investigated only the potential impact of the OBORI on the Chinese economy and geopolitics. Therefore, its real effect on Chinese international commerce in OBORI countries is not evaluated yet. Accordingly, this study intends to model the OBORI effect on Chinese product brand purchases across country members. The assessment is made on 18362 purchases of the International Online Consumers (IOCs) from a Chinese international online selling platform. The Data was obtained from a programming language and the octopus software. The OBORI policy's effect on Chinese brands' purchases was examined through a Different In Different Model (DIDM). Results show that the impact of OBORI is weak in the real market. However, it could be significant if OBORI includes more developed and economically strong countries. To Chinese brands and policymakers, we show how the inclusion in the OBORI project of developed countries could contribute more to Chinese product brands' purchases. Thus, the study enables decision-makers to understand the current impact of OBORI on the real market and its potential effect if more developed and economically strong countries are included.

This paper is concerned with a hydraulic cylinder directly controlled by a variable speed fixed displacement pump. The considered configuration is referred to as a one-motor-one-pump (1M1P) motor-controlled hydraulic cylinder (MCC). A 1M1P MCC with a hydraulically driven passive load-holding function enabled by controlled system pressures is proposed. The proposed load-holding functionality works if there is a standstill command, a loss of power supply, or a hose rupture. Additionally, this paper conducts a comprehensive analysis of the proposed system's operation and load-holding function across four quadrants. Simulation results demonstrate the four-quadrant operation and good load-holding performance under the aforementioned scenarios. In conclusion, the proposed 1M1P MCC can be successfully used on practical applications characterized by overrunning loads and four quadrant operation.

This paper presents machine learning methods for approximate solutions of reaction-diffusion equations with multivalued interaction functions. This approach addresses the challenge of finding all possible solutions for such equations, which often lack uniqueness. The proposed method utilizes physics-informed neural networks (PINNs) to approximate generalized solutions.

Dielectric barrier discharge (DBD) plasma has several applications in different fields. One of these fundamental applications is medical usages, where various methods are employed to improve the plasma treatment process. The combination of different gases is one of the important strategies to improve the performance of plasma in treatment. In this paper, the optimized plasma parameters for one-dimensional radiofrequency discharge produced at low pressures in a helium gas combination is studied. In this research, the optimal combination of H₂O and He is identified to attain the highest amount of reactive oxygen species (ROS). Considered mixture are 5,10,15 and 20 precent of H₂O for one dimensional helium gas discharge. The results show that the parameters of the output plasma are highly dependent on the composition of the input gases. It is found that the greatest concentrations of H+, He+, Hes (excited helium), and OH/ densities are observed when the H₂O percentage is 10%. Moreover, the density distributions of various species and the temperatures of electrons are numerically calculated during the electrical discharge process. These findings provide useful knowledge on how to optimize plasma parameters for biomedical applications, which may lead to improved treatment results in several therapeutic areas.

: Oscillation synchronization through diffusion-based communication of active materials can lead to emergence of diverse patterns and collective behaviors. A detailed general description of the formation process of synchronization or resynchronization dynamics is a challenging task. We employ a photosensitive Belousov-Zhabotinsky reaction-diffusion model (within a gel media) to investigate the recovery process of oscillation synchronization between a pair of gel patches. The recovery time for oscillation resynchronization can be modulated by patch-distance, species of signaling molecules, intensity and duration of illumination. Analysis reveals that the “switch effect” of the gel-distance and the “promotion effect” from illumination on the oscillation resynchronization originate from the competition between processes of photo-promotion of oscillation, diffusion of signaling molecules (HBrO2 and Br-) and disproportionation of HBrO2. These results will benefit studies on bio-inspired active materials and soft motors.

The increase in carbon dioxide emissions has a significant impact on human society and the global environment. As the most abundant and cheap C1 resource, the conversion and utilization of carbon dioxide has received extensive attention from researchers. In many methods of carbon dioxide conversion and utilization, the reverse water gas conversion reaction is considered to be one of the most effective ways. In this paper, the research progress of reverse water gas conversion reaction in recent years is introduced.

MoS2 has long been considered as a promising catalyst for hydrogen production. At present, there are many strategies to further improve its catalytic performance, such as edge engineering, defect engineering, phase engineering and so on. However, at present, there is still a great deal of controversy about the mechanism of MoS2 catalytic hydrogen production. For example, it is generally believed that the base plane of MoS2 is inert, but it has been reported that the inert base plane can undergo a transient phase transition in the catalytic process to play the catalytic role, which is contrary to the common understanding that the catalytic activity is only at the edge. Therefore, it is necessary to further understand the mechanism of MoS2 catalytic hydrogen production. In this article, we summarized the latest research progress on the catalytic hydrogen production of MoS2, which is of great significance for revisited the mechanism of MoS2 catalytic hydrogen production.

Dynamics of human populations can be affected by various socio-economic factors through their influence on the natality and mortality rates, and on the migration intensity and directions. In this work we study an economic-demographic model which takes into account the dependence of the wealth production rate on the available resources. In the case of nonlocal consumption of resources the homogeneous in space wealth-population distribution is replaced by a periodic in space distribution for which the total wealth increases. For the global consumption of resources, if the wealth redistribution is small enough, then the homogeneous distribution is replaced by a heterogeneous one with a single wealth accumulation center. Thus, economic and demographic characteristics of nonlocal and global economies can be quite different in comparison with the local economy.

Temperature influences the life of many organisms in various ways. A great number of them live under conditions, where their ability to adapt to changes in temperature can be vital and largely determine their fitness. Understanding the mechanisms and principles underlying this ability to adapt can be of great advantage, for example, to improve growth conditions for crops and increase their yield. In times of imminent, increasing climate change, this becomes even more important, in order to find strategies and help crops cope with these fundamental changes. There is intense research in the field of acclimation, that comprises fluctuations of various environmental conditions, but most acclimation research focuses on regulatory effects and the observation of gene expression changes within the examined organism. As thermodynamic effects are a direct consequence of temperature changes, these should necessarily be considered in this field of research, but are often neglected. Also, compensated effects might be missed, even though they are equally important for the organism, since they do not cause observable changes, but rather counteract them. In this work, using a systems biology approach, we demonstrate that even simple network motifs can exhibit temperature dependent functional features, resulting from the interplay of network structure and the distribution of activation energies over the involved reactions. The demonstrated functional features are (i) the reversal of fluxes within a linear pathway, (ii) a thermo-selective branched pathway with different flux modes and (iii) the increased flux towards carbohydrates in a minimal calvin cycle that was designed to demonstrate temperature compensation within reaction networks. By this, we expand the scope of thermodynamic modelling of biochemical processes by addressing further possibilities and effects, following established mathematical descriptions of biophysical properties.

The tsscds method, recently developed in our group, discovers chemical reaction mechanisms with minimal human intervention. It employs accelerated molecular dynamics, spectral graph theory, statistical rate theory and stochastic simulations to uncover chemical reaction paths and to solve the kinetics at the experimental conditions. In the present review, its application to solve mechanistic/kinetics problems in different research areas will be presented. Examples will be given of reactions involved in photodissociation dynamics, mass spectrometry, combustion chemistry and organometallic catalysis. Some planned improvements will also be described.

Fungi constitute a diverse group with highly positive and negative impacts in different envi-ronments, having several natural roles and beneficial applications in human life, but also caus-ing several concerns. Fungi can affect human health directly, but also indirectly by being detri-mental for animal and plant health influencing food safety and security. Climate changes are al-so affecting fungal distribution, prevalence, and their impact on different settings. Searching for sustainable solutions to deal with these issues is challenging due to the complexity of the inter-actions among fungi and agriculture, animal production, environment, and human health. In this way, the “One Health” approach may be useful to get some answers since it recognizes that human health is closely connected to animal and plant health, as well as to the shared environ-ment. This review aims to explore and correlate each of those factors influencing human health in this “One Health” perspective.

Four Fourier transforms are usually defined, the Integral Fourier transform, the Discrete-Time Fourier transform (DTFT), the Discrete Fourier transform (DFT) and the Integral Fourier transform for periodic functions. However, starting from their definitions, we show that all four Fourier transforms can be reduced to actually only one Fourier transform, the Fourier transform in the distributional sense.

Background: Swept-source anterior segment optical coherence tomography (SS-AS- OCT) is a suitable examination for the vitreolenticular interface. Methods: In a prospective study using Anterion (Heidelberg Engineering, Heidelberg, Germany) 102 eyes of 102 patients were examined, in pupil dilation, preoperatively and 6 times over 1-year follow-up. Preoperatively anterior hyaloid membrane (AHM) visibility was determined with Imaging App with high reliability. Postoperatively capsular bag–AHM distance was measured on six points by using Metrics App. Results: The AHM was visible in 18.6% preoperatively and postoperatively as well (Group 1), 49% of the preoperatively adherent AHMs became visible (Group 2A), 32.4% remained attached (Group 2B). Group 1: the average deepest point first day was 782.5 ± 324.1 microns, and it significantly differed from the later follow-up values. Group 2A: the average deepest value was 184.1 ± 220.1 microns, and there was no statistically significant difference between the postoperative visit values. The difference between the groups was statistically significant at every location and at each time points. Conclusions: AS-SS-OCT can be used to check BS both preoperatively(with limitations) and postoperatively.

Objective: The effect of long-term performance of one-bottle or two-bottle bonding agents on the shear bond strength to lithium disilicate ceramics (LDS) were to investigate, and the long-term performance of the bond strength of two-bottle bonding agent (Tokuyama Universal Bond II) was investigated under conditions without hydrofluoric acid solution (abbreviated as HF)-pretreatment of LDS. Methods: Nine resin cements (both self-adhesive and adhesive types) were used. It was investigated 1) the adhesion strength of various resin cements to LDS from the presence or absence of HF-treatment, 2) to determine the effect of the deterioration in three times [after one-day storage (abbreviated as Base), and after 5,000 &amp; 20,000 thermocycles (abbreviated as TC 5k and TC 20k)] of one- and two-component bonding agents. And the difference in degradation between one- and two-component bonding gents consist of the silane coupling agent was performed by chemical analysis (High Performance Liquid Chromatography). Results: The trends of resin cements were statistically not very different for each cement 3 times with HF-conditions. Also ESTECEM II and Super-Bond Universal showed the significant greatest values in two conditions (TC 5k and TC 20k) without HF-condition. In TC 20k, ESTECEM II &amp; Super-Bond Universal showed significantly better results than others when treated with the recommended bonding agents without HF-condition. In TC 20k, there was not much statistically significant difference if pretreated with Tokuyama Universal Bond II without HF-condition. Significance: When using LDS, it was found that long-term durability could be maintained by pretreating with Tokuyama Universal Bond II without pretreating with various hazardous HFs.

Globally increasing antibiotic resistance has been connected to the use of antibiotics in medical, veterinary, and agricultural medicine, contributing to the burden of antibiotic resistance in Asia and Europe. The main objective of this study was to correlations of antimicrobial-resistant of various pathogens in three compartments: humans, animals and the environment in India and Germany. A systematic search was carried out in Medline via PubMed, Google Scholar, and science direct, including studies published in 2022. Out of 532 papers, 24 were considered for meta-analysis. This study reveals that in India, β-lactam is highly resistant in animals. Quinolone, on the other hand, was highly resistant in humans. Furthermore, in the environment and integrated studies, aminoglycosides and β-lactams is resistant. While in Germany, a high rate of AMR resistance in all three sectors was reported in β-lactam. However, E. coli was the most frequent pathogen in both countries and is highly resistant to β-lactam, followed by cephalosporin in all the compartments. Monitoring and evaluating antibiotic-sensitivity patterns and developing proper antibiotic regimens may lead to improved outcomes for inhibiting and controlling E. coli infections in various parts of the world.