Achieving the thermal conductivity required for efficient heat management in semiconductors and other devices requires the integration of thermally conductive ceramic fillers at concentrations of 60 vol% or higher. However, the increased filler content often negatively affects the mechanical properties of the composite matrix, limiting its practical applicability. To address this issue, in this paper, we present a new strategy to reduce the required ceramic filler content: the use of a thermally conductive ceramic composite filler with carbon nanotubes (CNT) grown on aluminum nitride (AlN). We have combined catalyst coating technology with vacuum filtration to ensure that the catalyst is uniformly applied to micrometer-sized AlN particles, followed by efficient and uniform synthesis of CNTs using a water-assisted process in a vertical furnace. By carefully controlling the number of vacuum filtration cycles and the growth time of the CNTs, we demonstrate precise control over the number and length of the CNT layers, thereby adjusting the properties of the composite to the intended specifications. When AlN/CNT hybrid fillers are incorporated into silicone rubber, while maintaining the mechanical properties of rubber, the thermal diffusivity achieved at reduced filler levels exceeds that of composites using AlN-only or simultaneous AlN and CNTs formulations. This demonstrates the critical role of CNTs on AlN surfaces. Our study represents a significant advancement in the design of thermally conductive materials with potential implications for a wide range of applications.

The chemical investigation of the anti-yeast methanol extract from the stem bark of Terminalia mantaly led to the isolation of seven compounds: 3-O-methyl-4-O-α-rhamnopyranoside ellagic acid (1), 3-O-mehylellagic acid (2), arjungenin or 2,3,19,23-tetrahydroxyolean-12-en-28-oïc acid (3), arjunglucoside or 2,3,19,23-tetrahydroxyolean-12-en-28-oïc acid glucopyranoside (4), 2α,3α,24-trihydroxyolean-11,13(18)-dien-28-oïc acid (5), stigmasterol (6), stigmasterol 3-O-β-D-glucopyranoside (7). Their structures were established by means of spectroscopic analysis and comparison with published data. Compounds 1-5 were tested in vitro for activity against three pathogenic yeast isolates, Candida albicans, Candida parapsilosis and Candida krusei. The activity of compounds 1, 2 and 4 were comparable to that of the reference compound fluconazole (MIC values below 32 µg/ml) against the three tested yeast isolates. They were also tested for inhibitory properties against four enzymes of metabolic significance: Glucose-6-Phosphate Deshydrogenase (G6PD), human erythrocyte Carbonic anhydrase I and II (hCA I and hCA II), Glutathione S-transferase (GST). Compound 4 showed highly potent inhibitory property against the four tested enzymes with overall IC₅₀ values below 4 µM and inhibitory constant (Ki) <3 µM.

During the last years there has been a high interest in the development of new purely-organic single-component conductors. Very recently, we have reported a new neutral radical conductor based on the perchlorotriphenylmethyl (PTM) radical moiety linked to a monopyrrolo-tetrathiafulvalene (MPTTF) unit by a -conjugated bridge (1). Interestingly, this system behaves as a semiconductor with high conductivity and small energy gap under high pressure. With the aim of developing a new material with improved conducting properties, we have designed and synthesized the radical dyad 2 which was functionalized with an ethylenedithio (EDT) group in order to improve the intermolecular interactions of the TTF subunits. The physical properties of the new radical dyad 2 were studied in detail in solution to further analyze its electronic structure as well as its potential use as radical conductor in the solid state.

Leishmaniasis are neglected diseases that affect regions such as South Asia, South Africa and Latin America, less developed regions. Current treatment, for cutaneous, mucocutaneous and visceral leishmaniosis, which are the main forms of the disease, is based on the administration of pentavalent antimonial and amphotericin B. However, these drugs have low efficacy and high toxicity. For this reason, the search for new treatments for this disease is necessary, based on studies of new molecules and their conformations. The research proposed the conformational study of brominated guanidine compounds with potential antileishmanial activity using Nuclear Magnetic Resonance (NMR) and X-ray diffraction (XRD) techniques. The present study involves the bro-minated molecules, LQOF-G2, LQOF-G30, LQOF-G35 and LQOF-G35-Br. The later was synthesized by the reaction of LQOF-G35 with NBS under IR irradiation at 120 Watts of potency and dichloro-methane as solvent by 12-h of exposition. The obtained results demonstrated the efficiency of the bromination method, since two bromines atoms entered the molecule. Furthermore, NMR analysis showed the occurrence of a conformational change from Z to E when compound LQOF-G35 was brominated to LQOF-G35-Br. This feature was well confirmed by comparative DRX study of the LQOF-G35 and LQOF-G35-Br compounds. The antileishmanial activity of LQOF-G2 e LQOF-G35 motivated the synthesis of new brominated compounds LQOF-G30 e LQOF-G35-Br.

Indole is a versatile pharmacophore widely distributed in bioactive natural products. This privileged scaffold has been found in a variety of molecules isolated from marine organisms such as algae and sponges. Among these, indole alkaloids represent one of the biggest, most promising family of compounds, having shown a wide range of pharmacological properties, including anti-inflammatory, antiviral and anticancer activities. The aim of this review is to show the current scenario of marine indole alkaloid derivatives, covering not only the most common chemical structures, but also new synthetic routes developed during the last years as well as promising therapeutic applications.

The critical role of global electron density transfer (GEDT) in increasing the reaction rate of polar organic reactions has been studied within the framework of Molecular Electron Density Theory (MEDT). To this end, the series of the polar Diels-Alder (P-DA) reactions of cyclopentadiene with cyanoethylene derivatives, for which experimental kinetic data are available, have been chosen. A complete linear correlation between the computed activation Gibbs free energies and the GEDT taking place at the polar transition state structures (TSs) is found; the higher the GEDT at the TS, the lower the activation Gibbs free energy. An interacting quantum atoms (IQA) energy partitioning analysis allows establishing a complete linear correlation between the electronic stabilization of the electrophilic ethylene frameworks and the GEDT taking place at the polar TSs. This finding supports Parr’s proposal for the definition of the electrophilicity  index (J. Am. Chem. Soc., 1999, 121, 1922). The present MEDT study allows establishing the critical role of the GEDT in the acceleration of polar reactions, since the electronic stabilization of the electrophilic framework with the electron density gain is greater than the destabilization of the nucleophilic one, making a net favorable electronic contribution to the decrease of the activation energy.

In this work, we designed a MEMS device which allows simultaneous direct measurement of mechanical properties during deformation under external stress and characterization of the evolution of microstructure of nanomaterials within a transmission electron microscope. This MEMS device makes it easy to establish the correlation between microstructure and mechanical properties of nanomaterials. The device uses piezoresistive sensors to qualitatively measure the force and displacement of nanomaterials, e.g., in wire and thin plate forms. The device has a theoretical displacement resolution of 0.19 nm and a force resolution of 2.1 μN. The device has a theoretical displacement range limit of 2.74 μm and a load range limit of 27.75 mN.

This paper presents laboratory devices on which experimental measurements were carried out to prove the validity of the assumption about the reduction of vibrations transmitted to the conveyor belt structure generated by the impact forces of falling material grains in the places of transfer or on the hoppers of conveyor belts. In order to limit damage to the conveyor belts caused by the impact of the sharp edges of material grains, conveyor belts are supported by impact rollers or impact rubber rods in the places of transfers and on the hoppers of belt conveyors. The flattened ends of the impact rollers are inserted into the grooves of steel brackets installed on the supports of the fixed conveyor idlers of a conventional design. In this paper, a special modification of the fixed conveyor idler is presented, which consists of inserting plastic brackets into the structurally modified roller axle holders of the fixed conveyor idler. Measurements were carried out on the first laboratory device, which showed that the specially modified fixed conveyor idler resulted in a higher damping of up to 15% of the impact forces of the falling weight on the rubberized hoop of the impact roller shell compared to the conventional fixed conveyor idler design. Measurements carried out on the second laboratory device show that the effective vibration velocity values detected at the points where the impact roller axis fits into the fixed roller table holder, i.e. points B and D, are higher than when using plastic brackets, up to 6% for a 108 mm diameter roller, compared to steel impact roller brackets.

This article presents a new input device for spastic patients and others with similar symptoms. The sensor consists of a disc used to determine positions and can replace standard joysticks in medical devices such as electric-powered wheelchairs. Using a standard joystick while operating a powered wheelchair can result in dangerous situations when spastic movements occur and extremities cramp making them uncontrollable. To avoid this, a disc was developed that can be controlled with any body part. By shifting weight (x- and y-axis) the disc can tilt in any direction creating a proportional output signal and can also be pushed down in the center (z-axis) to open a menu on a screen for example. When spasms occur it is impossible for users to get stuck on the input device because the disc is flat and can be mounted within a control panel. Body parts coming into contact with the disc would merely slide across the disc without triggering unintentional actions. The sensor presented here is also adaptive and can be adjusted to fit a user’s strength and range of motion. This proposal aims to develop an input device that enables spastic patients to operate sensitive systems safely.

SOC stock (SOCS) changes caused by land use changes are still unclear, and understanding this response is essential for many environmental policies and land management practices. In this study, we investigated the temporal-spatial and vertical distribution characteristics of SOCS on the Western Sichuan Plateau (WSP) using the sparrow search algorithm-random forest regression (SSA-RFR) models with excellent model applicability and accuracy. The temporal-spatial varia-tions in the SOCS were modeled using 1080 soil samples and a set of nine environmental covariates. We analyzed the effect of land use changes on the SOCS on the WSP. The total SOCS increased by 18.03 Tg C from 1990 to 2020. The results of this study confirmed that the SOCS in the study area has increased significantly since 2010, with an increase of 27.88 Tg C compared to the total SOCS in 2010. We found that the spatial distribution of the SOCS increased from southeast to northwest, and the vertical distribution of the SOCS in the study area decreased with increasing soil depth. Forest and grassland are the main sources of SOCS, the total SOCS in the forest and grassland accounted for 37.53 and 59.39% of the total SOC pool in 2020, respectively. Expansion of the wetlands, forest, and grassland areas could increase SOCS in the study area.

(1) Background: In this work, a series of benzimidazole derivatives containing colchicine-like and cathechol-like moieties with methyl group substitution in the benzimidazole ring were evaluated for their in vitro antiproliferative, pro-apoptotic and antioxidative activity against highly invasive breast cancer cell line MDA-MB-231 and related impairment of tubulin dynamics; (2) Methods: MTT assay was used to evaluate the antiproliferative activity. In vitro tubulin polymerization assay as well as docking analysis was applied to prove the alterations in tubulin polymerization. Immunofluorescent and DAPI staining reveal the pro-apoptotic potential of benzimidazole derivatives and the effect on tubulin’s dynamics in living cells. The antioxidant activity was evaluated by scavenging of H2O2 and hypochlorite ion and ortho-phenanthroline tests; (3) Results: The compounds containing colchicine-like moiety displayed significant growth inhibitory effect against cancer cell line as was highlighted the role of methyl functional group on the tubulin aggregation and blockage of mitosis. All compounds showed an ability to scavenge H2O2, while the compounds with cathecol-like moiety were more effective against hypochlorite ion and chelation of iron; (4) Conclusions: The benzimidazole derivative containing colchicine-like moiety and methyl group substitution in benzimidazole ring is a potential antiproliferative and microtubule destabilizing agent.

An easy to implement and cost-effective Fiber Bragg Grating (FBG) sensor interrogation technique based on a ring Erbium-Doped Fiber Laser (EDFL) topology is proposed and experimentally assessed. The FBG sensor is part of the EDFL cavity and must have a central wavelength located within the linear region of the EDF’s amplified spontaneous emission (ASE) spectrum which occurs between 1530 and 1540nm. In this manner, the wavelength-encoded response of the FBG under strain is converted to a linear variation of the laser output power, removing the need for spectrum analysis as well as any limitations from the use of external edge-filtering components. In addition, the laser linewidth is significantly reduced with respect to the FBG bandwidth thus improving the resolution of the system, whereas its sensitivity can be controlled through the pumping power. The performance of the system has been characterized by modeling and experiments for EDF's with different lengths, doping concentrations and pumping power levels. The influence of mode-hopping in the laser cavity on the resolution and accuracy of the system has also been investigated.

Honey is a sweet substance extensively consumed in the world for its nutritional and healthy properties. However, residues of pesticides and environmental contaminants can compromise its quality. For this reason, the physicochemical parameters, and the organic contamination of monofloral and multifloral honeys from three regions of Algeria (Tiaret, Laghouat and Tindouf) were monitored to evaluate the quality of honey and the safety for consumers. In general, the results obtained from the physicochemical analyses were in line with the EU standards. In terms of contamination, pesticides authorised and used in Algerian agriculture (matalaxyl-M and cyromazine), as well as banned pesticide (carbaryl), were found in almost all the samples. However, only the concentration of cyromazine was higher than the relative EU maximum residue levels. PCB 180, PCB 189, anthracene, fluorene and phenanthrene were mainly detected. All the honeys show traces of DiBP, DBP, DEHP and DEHT, but no traces of bisphenols were found. Moreover, the dietary exposure assessment shows that a small amount of Algerian honey can be safely consumed. Overall, data from this study should motivate the Algerian government to enhance their monitoring activities in beekeeping and to find solutions for implementing more sustainable agricultural practices harmonizing with the international legislation.

The increasing regulatory pressure to monitor and reduce GHG emissions and air pollutants requires cost-effective methods for their surveillance. The most common technique used for scientific investigations on gas concentration monitoring in barns are accurate but expensive and with a complex maintenance. This research study analysed the potential use of a low-cost portable measurement devices for the measurement of ammonia (NH3) and carbon dioxide (CO2) concentrations in an open dairy barn. A comparison between gas concentrations acquired at different heights from the floor by using portable devices and those acquired by a photoacoustic infrared multigas spectroscope (i.e., reference measurement) in the same sampling locations was carried out to determine the precision of the low-cost portable devices. The performance of low-cost portable devices was statistically analysed by the application of the one-way analysis of variance, correlation analysis and regression analysis. The results showed a significant difference between gas concentration values at various heights from the floor for both NH3 and CO2. The correlations between concentrations acquired by the low-cost portable device and the INNOVA were statistically significant (r=0.83; P&lt;0.001) for gas concentrations monitored at 0.4 m from the floor. Compared with the reference measurement device, the low-cost devices were effective in the monitoring of NH3 concentrations at 0.40 m from the floor though it underestimated them in the barn at increasing of the height from the floor, whereas the device was not adequate for CO2 concentrations. In detail, the relative measurement error of the low-cost devices compared to INNOVA was reduced close to the floor during NH3 concentration measurements. Within these limitations, this device could be useful for monitoring NH3 concentration in the barn and to assess variation in NH3 concentrations mainly related to the animal occupied zone. Further efforts are needed in this field of research to identify low-cost device that could simplify emission estimation from open dairy barns.

Promoting organic foods production and consumption contributes to accomplishing United Nations sustainable development goals. Social commerce provides a promising opportunity to develop the organic food industry. However, there is limited knowledge regarding customer behaviors in relation to purchasing organic foods via social commerce platforms. Therefore, this study expanded upon the unified theory of acceptance and use of technology (UTAUT-2) to develop a comprehensive model that explains how customers' social commerce trust and behavioral intentions to purchase organic foods using Instagram social commerce affect their purchasing behaviors. The research model was analyzed by employing partial least squares structural equation modeling (PLS-SEM) for the data collected from a quantitative survey of 410 customers who used Instagram to purchase organic foods in Iran. The results revealed that facilitated purchasing conditions, hedonic motivations, social influence, rating and reviews, and influencers’ endorsements increase customers' purchase intentions. Moreover, Instagram’s recommendations and referrals, influencers’ endorsements, as well as social influence boost customers' trust in the social commerce platform. Eventually, it was determined that influencers’ endorsements, social commerce trust, and purchase intention determine a customer’s organic foods purchasing behaviors. This research provides valuable insights for organic food marketers to optimize their social commerce strategies.

Objective: This study aimed to demonstrate the availability of portable devices for nasal FeNO measurement, which could replace exhaled NO measurement based on the continuous aspiration of multiple flow measurement systems. Methods: A descriptive cross-sectional study. The healthy subjects without rhinosinusis disorders (control group) and those with diagnosed allergic rhinitis (AR group) were enrolled in the study. They underwent nasal and bronchial FeNO measurements by both fixed flow NObreath® connected to nasal mask and multiple flows HypAir FeNO®. Results: A total of 153 people were recruited including 63 healthy subjects and 90 subjects with AR. There were no statistically significant differences in anthropometric characteristics between the two groups (P > 0.05). There were a significant increase in FeNO values in the AR group compared to the control group; concentrations of nasal and bronchial FeNO mearsured by NObreath® were 76.0 ± 50.7 ppb (vs 36.0 ± 28.1 ppb, P < 0.01) and 32.3 ± 15.4 ppb (vs 9.2 ± 5.6 ppb, P < 0.001), and those mearsured by NObreath® Hypair FeNO® were 1796.9 ± 523.3 ppb (vs 400.2 ± 123.1 ppb, P < 0.001) and 37.3 ± 23.0 ppb (vs 17.4 ± 18.3 ppb, P < 0.01). A weak correlation between the values measured by NObreath® and Hypair FeNO® devices was observed (r = 0.023 and r = 0.089, respectively; p < 0.05). Conclusions: The handheld NObreath® device is effective in measuring FeNO concentrations in both normal subjects and AR patients. The advantages in price and size, creating a compact, low-cost device that is convenient for use and research.

Scedosporium species are human pathogenic fungi, responsible for chronic, localised, and life-threatening disseminated infections in both immunocompetent and immunocompromised individuals. Diagnosis of Scedosporium infections currently relies on non-specific CT, lengthy and insensitive culture from invasive biopsy, and time-consuming histopathology of tissue samples. At present, there are no rapid antigen tests that detect Scedosporium-specific biomarkers. Here we report the development of a rapid (30 min) and sensitive (pmol/L sensitivity) lateral-flow device (LFD) test, incorporating a Scedosporium-specific IgG1 monoclonal antibody (mAb), HG12, which binds to extracellular polysaccharide (EPS) antigens of between ~15 kDa and 250 kDa secreted during hyphal growth of the pathogens. The test is compatible with human serum, and allows the detection of the Scedosporium species most-frequently reported as agents of human disease (Scedosporium apiospermum, Scedosporium aurantiacum, and Scedosporium boydii), with limits of detection (LOD) of the EPS biomarkers in human serum of ~0.81 ng/mL (S. apiospermum), ~0.94 ng/mL (S. aurantiacum), and ~1.95 ng/mL (S. boydii). The Scedosporium-specific LFD (ScedLFD) test therefore provides a potential novel opportunity for the detection of infections caused by different Scedosporium species.

Byers Peninsula is considered one of the largest ice-free areas in Maritime Antarctica. Since 2006, the Spanish Polar Program has taken part in a large number of environmental studies involving effects of climate changes in lives cycles, limnology and microbiology. Soils from maritime Antarctica are generally weakly developed and have chemical, physical and morphological characteristics strongly influenced by the parent material. However, biological activity during the short Antarctic summer promotes intense transference of nutrients and organic matter in areas occupied by different species of birds and marine mammals. To mapping and monitoring those areas with high biological occupation, could be very useful to have models of edaphic properties prepared from satellite images. In this approach, Deep Learning and Linear Regression models of soil properties and spectral indexes as explicative variables were performed. We training models of soil properties closely related to biological activity such as Dissolved Organic Carbon (DOC) and the iron fraction associated with organic matter (Fe). We tested the best approach to model the spatial distribution of DOC, Fe and pH by training models of Linear Regression and Deep Learning over Sentinel2 and WorldView2 images. The most robust models were used to track possible areas with ornithogenic soils as well as areas of the Byers Peninsula that could support the highest biological development.

Although mammography has been the gold standard for early detection of breast cancer, if a woman has dense breast tissue, a false negative diagnosis may occur. Breast ultrasound, whether hand-held or automated, is a useful adjunct to mammography but adds extra time and cost. The primary aim was to demonstrate that our second-generation Aceso system, which combines full-field digital mammography (FFDM) and automated breast ultrasound (ABUS) in a single platform, is able to produce improved quality images that provide clinically meaningful results. Aceso was first tested using two industry standards: a CDMAM phantom to assess the FFDM images; and the CIRS 054GS phantom to evaluate the ABUS images. In addition, 25 women participated in a clinical trial: 14 were healthy volunteers while 11 were patients referred by the breast clinic at Groote Schuur Hospital. The CDMAM phantom results showed the FFDM results were better than EUREF’s standard of “acceptable” and were approaching “achievable”. The ABUS results showed lateral and axial spatial resolution of 0.5 mm and adequate depth penetration of 80 mm. Our second-generation Aceso system, with its improved quality of clinical FFDM and ABUS images, has demonstrated its potential for early detection of breast cancer in a busy clinic.

Soil organic matter (SOM) is important for the global carbon cycle, and hyperspectral remote sensing has proven a promising method for fast SOM content estimation. However, soil physical properties significantly affect the sensitivity of satellite hyperspectral imaging to SOM, leading to poor generalization ability of the estimation model. This study aims to improve the spatiotemporal transferability of the SOM prediction model by alleviating the coupling effect of soil physical properties on the spectra. Based on satellite hyperspectral images and soil physical variables, including soil moisture (SM), soil surface roughness (root mean squared height, RMSH), and soil bulk weight (SBW), a soil spectral correction strategy was established based on the information unmixing method. Two important grain-producing areas in Northeast China were selected as study areas to verify the performance and transferability of the spectral correction model and SOM content prediction model. The results showed that soil spectral corrections based on fourth-order polynomials and the XG-Boost algorithm had excellent accuracy and generalization ability, with residual predictive deviations (RPD) exceeding 1.4 in almost all bands. In addition, when the soil spectral correction strategy was adopted, the accuracy of the SOM prediction model and the generalization ability after model migration were significantly improved. The SOM prediction accuracy based on the XG-Boost corrected spectrum was the highest, with a coefficient of determination (R2) of 0.76, root mean square error (RMSE) of 5.74 g/kg, and RPD of 1.68. The prediction accuracy, R2, RMSE, and RPD of the model after migration were 0.72, 6.71 g/kg, and 1.53, respectively. Compared with the direct migration prediction of the model, adopting the soil spectral correction strategy based on fourth-order polynomials and XG-Boost reduced the RMSE of the SOM prediction results by 57.90% and 60.27%, respectively. The performance comparison highlighted the advantages of considering soil physical properties in regional-scale SOM prediction.

.Maize cultivation in Thailand faces challenges owing to climate change and soil organic carbon (SOC) loss. This highlights the importance of comparing maize soil with paddy soil in terms of the role of dissolved organic carbon (DOC) and nutrient availability, as they influence SOC content. Soil samples from Chiang Mai province, primarily Fluvisol, were collected for the cultivation of paddy rice and maize, analysed for carbon fractions and chemical properties, and categorised into layers. Comparative analysis revealed that maize soils had lower levels of labile carbon components and organic carbon than paddy soils (P

One of the most concerning global environmental issues is the pollution of agricultural soils by heavy metals (HMs), especially cadmium (Cd), which not only affects human health by taking Cd-containing foods but also impacts the quality of rice. The soil's nitrification and denitrification processes, coupled with the release of volatile organic compounds by plants, raise substantial concerns. The understanding of three aspects of paddy soil under conditions of heavy-metal pollution and water management is currently limited. In this review, we summarized recent literature related to the deleterious effects of Cd on both soil processes related to the N cycle and rice quality, particularly aroma, in different water management practices. Under both continuous flooding (CF) and alternate wetting and drying (AWD) conditions, cadmium (Cd) has been observed to reduce both nitrification and denitrification processes. The adverse effects are more pronounced in continuous flooding (CF) compared to alternate wetting and drying (AWD). Similarly, the alteration in rice aroma is more significant in AWD than in CF. The precise modulation of volatile organic compounds (VOCs) by Cd, remains unclear based on the available literature. Nevertheless, HM accumulation is higher in AWD conditions compared to CF, leading to a detrimental impact on volatile organic compounds (VOCs). The literature concluded that AWD practices should be avoided in Cd contaminated fields to decrease accumulation and maintain the quality of rice. In the future, rhizospheric engineering and plant biotechnology can be used to decrease the transport of HMs from the soil to the plant’s edible parts.

In this study, a new type of temperature sensor device was developed. The circular electrode of the thermal sensitive sensor was modified with TMT and O₂ plasma to enhance the conductivity by forming a thin SnOxCy layer on the electrode surface. The Nano-Au particles were subjected to O₂ plasma pretreatment to form peroxide groups on the surface. The thermally sensitive sensor was made by mixing the above-treated Nano-Au particles with N-isopropylacrylamide (NIPAAm) to form solution and then UV-induced grafting polymerization of the NIPAAm-containing solution onto the electrode substrate. The composite hydrogels on the electrode introduce thermo-sensitive polymeric surface films for temperature sensing. Using ambient environment resistance test to measure the resistance, the LCST (lower critical solution temperature) of Nano-Au (MUA) mixed with NIPAAm hydrogel was found to be 32 °C. At ambient temperatures higher than LCST, the electrode resistance decreases linearly.

A time-sequential working, spatially multiplexed autostereoscopic 3D display design consisting of a fast switchable RGB-color filter array is presented. The wavelength-selective filter barrier emits the light from a display over a larger active area than common autostereoscopic barrier displays. An optical modelling of wavelength-selective barriers has been used for instance to calculate the light ray distribution properties of that arrangement. To find well working display designs, automated searches by simulation and computational evaluation has been proceeded. Wavelength-selective filter barrier arrangements exhibit characteristics different from common barrier displays with similar barrier pitch and ascent. In particular, these constructions show strong angular luminance dependency under barrier inclination specified by correspondent slant angle. In time-sequential implementation it is important to avoid that quick eye or eyelid movement lead to visible color artifacts. In the millisecond regime tunable liquid crystal Fabry-Pérot color filters for the colors red, green and blue are presented. They consist of a sub-micrometer thick nematic layer sandwiched between dielectric mirrors and ITO-electrodes. These cells shall switch narrow-banding light of red, green or blue. An array for a glasses-free 3D display has to be equipped with several thousand switchable filter elements having different color apertures. The newly introduced design is usable as a multi user display as well as a single user system with user adaptive control.

Spectral characteristics of CDOM in water column are a key parameter for bio-optical modeling. Knowledge of CDOM optical properties and spatial discrepancy based on the relationship between water quality and spectral parameters in Yinma River watershed with in situ data collected highly-polluted waters are exhibited in this study. Seasonal field data sets collected over a period of 2 months in 2015 in Yinma River Watershed. Based on the comprehensive index method, the riverine waters showed serious contamination, especially the COD, Fe, Mn, Hg and DO were out of range contamination warning. Dissolved organic carbon (DOC) and total suspended matter (TSM) with prominent non-homogenizing were significantly high in the riverine waters, but chlorophyll-a (Chl-a) was opposite. Ternary phase diagram showed that non-algal paritcles absorption played an important role in total non-water light absorption (>50%) in most sampling locations, and mean contribution of CDOM were 13% and 22% in summer and autumn respectively. Analysis of ratio of absorption at 250-365 nm (E_250:365) and spectral slope (S_275-295) indicated that CDOM had higher aromaticity and molecular weight in autumn than in summer, is consistent with the results of water quality and relative contribution. Redundancy analysis (RDA) indicated that the environmental variables OSM had a strong correlation with CDOM absorption, followed by heavy metal, e.g., Mn, Hg and Cr⁶⁺. However, for the specific UV absorbance (SUVA₂₅₄), the seasonal values showed opposite results compared with the reported literature. The potential reasons were the more UDOM (uncolored Dissolved Organic Matter) from human source (wastewater effluent) existed in waters. Terrigenous inputs simultaneously are in relation to the a_CDOM(440)-DOC relationship with the correlation coefficient was 0.90 in summer (2-tailed, p<0.01), and 0.58 in autumn (2-tailed, p<0.05). Spatial distribution of CDOM parameters exhibited that the downstream regions focused on dry land have high CDOM molecular weight and aromatic hydrocarbon. Partial sampling locations around the cities or countries generally showed abnormal values due to terrigenous inputs. As a bio-optical model parameter, spectral characteristic of CDOM is helpful in adjusting the derived algorithms in highly-polluted environments. The study on organic carbon and pollutants in highly-polluted waters had an important contribution to global carbon balance estimation and water environment protection.

The objective of this work was to investigate the deacidification of bio-oils (BOs) from triglyceride-based biomass through the application of liquid-liquid extraction (LLE) in a simple stage, using methanol and water as a binary solvent and feed/solvent ratio of 1/1. For this, the effects of process parameters such as the water content present in the solvent, the content of carboxylic acids present in the bio-oil, and the extraction temperature on the deacidification process through the efficiency and distribution coefficient were evaluated, as well as the effects of such parameters on the quality of deacidified bio-oils through physical-chemical analyzes and GC-MS analysis. The results show that such process parameters significantly affect the quality of deacidified bio-oils. The ideal condition to have the highest acid removal, i.e., the highest deacidification efficiency (72.65%), is the one in which the deacidification process is performed with aqueous methanol (5% water) at 35 °C and for BOs that have a total acid number (TAN) equal to 24.38 mg KOH/g. Therefore, the process of deacidification by LLE using aqueous methanol is a promising alternative for removing carboxylic acids and other oxygenated compounds, contributing significantly to the upgrading or improving biofuels produced by catalytic thermal cracking.

Reactions of quinones with compounds containing an amino group can produce a wide variety of addition or substitution products that depend on reactivity of both quinone and amino derivative. 6,7-Dichloropyrido[1,2-a]benzimidazole-8,9-diones undergo selective nucleophilic substitution reaction with different benzohydrazides and α-hydroxy-p-quinone imine derivatives stabilized by strong intramolecular hydrogen bond were isolated. Synthesized compounds represent a combination of several structural motifs: benzimidazole core fused with α-hydroxy-p-quinone imine which contains a benzamido fragment. The protonation/deprotonation processes were investigated in a solution using UV-Vis spectroscopy and 1H NMR titration experiment. X-ray crystallography analysis revealed a set of weak non-covalent interactions such as intra- and intermolecular hydrogen bonds and π-π stacking. Additionally, the redox behavior of 6,7-dichloropyrido[1,2-a]benzimidazole-8,9-dione and its p-imino derivative was investigated in acidic and neutral environment using cyclic voltammetry measurements. Cathode material based on 6,7-dichloropyrido[1,2-a]benzimidazole-8,9-dione could act as potential effective active electrode in aqueous electrolyte batteries, however further optimization is required.

The long-term use of fertilizers and pesticides in conventional cultivation has resulted in a decrease in soil productivity and vegetable yields in greenhouses. However, only a limited number of studies have explored the impacts of organic cultivation on greenhouse soil. Specifically, there is a scarcity of research examining the alterations in soil aggregate mediated organic carbon and microbial communities, which are known to enhance soil productivity. This study investigated the properties of soil aggregates, including the levels of organic carbon fractions, microbial community, and enzyme activity with the three aggregate classes microaggregates (&lt;0.25 mm), small macroaggregates (2-0.25 mm) and large macroaggregates (&gt;2 mm). These investigations were conducted under three different cultivation methods in a greenhouse: conventional cultivation (CC), integrated cultivation (IC), and organic cultivation (OC) in greenhouse. The results showed that (1) OC and IC promoted the formation of small macro-aggregates and enhanced aggregate stability compared to CC, (2) SOC in the three size fractions of OC increased by 98.99%-92.06% compared to CC; EOC increased by 98.47%-117.59%; POC increased by 138.59%-208.70%; MBC increased by 104.71%-230.61%; DOC increased by 21.93%-40.90%, respectively; (3) Organic cultivation significantly increased enzyme activity in all three particle size aggregates and increased the relative abundance of bacteria in micro-aggregates as well as the relative abundance of fungi in small macro-aggregates. Structural equation model (SEM) analysis revealed that organic farming practices fostered the development of smaller macro-aggregates, elevated microbial and enzyme activities within soil aggregates, and facilitated the conversion of soil nutrients and carbon sequestration. consequently, this led to an increase in soil organic carbon content and improved vegetable yield in greenhouse environments. In conclusion, the soil carbon content and vegetable yield are enhanced through long-term organic cultivation in greenhouses, primarily by increasing the proportion of small macro-aggregates.

Cardiac amyloidosis is caused by amyloid fibrils that deposit in the myocardial interstitium, causing restrictive cardiomyopathy and eventually death. The electromechanical, inflammatory, and autonomic changes due to amyloid deposition result in arrhythmias. Atrial fibrillation is by far the most common arrhythmia. Rate control strategy is generally poorly tolerated due to restrictive filling physiology and heart rate dependance, favoring adoption of rhythm control strategy. Anticoagulation for stroke prophylaxis is warranted irrespective of CHA2DS2Vasc score in patients with favorable bleeding profile; data on left appendage closure devices is still insufficient. Ventricular arrhythmias are also not uncommon and the role of implantable cardioverter-defibrillator in cardiac amyloidosis is controversial. There is no evidence of improvement in outcomes when used for primary prevention in these patients. Bradyarrhythmia is most commonly associated with sudden cardiac death in cardiac amyloidosis. Pacemaker implantation can help provide symptomatic relief but does not confer mortality benefit.

The eutrophication of open water bodies, especially in coastal water area, has received intensive public focuses in recent years. Biological treatment of organic pollutants in industrial and domestic wastewater requires microbial flora to participate. The environmental impact of these microbes, particularly in regard to the spread of antibiotic resistance genes and pathogenicity in coastal water, remains largely unknown. We initiate studies to examine antibiotic resistance genes (ARGs) in microbial flora and study the mode of antibiotic spread in the coastal waters of Bohai Bay, North China by using high performance liquid chromatography-mass spectrum analysis and quantitative polymerase chain reaction. The metabolic features of bacteria related to the presence of ARGs in the coastal area showed the enrichment of Pseudomonadale species with triple resistance properties (ampicillin, kanamycin and gentamycin) at the estuary site locating adjacent to a coastal sewage treatment plant where both type I and type II polyketide synthase genes and b-lactam type antibiotics are detected. Pseudomonadale order is phylogenetically belonged to Proteobacteria Phylum, Gamma-proteobacteria Class and contains Pseudomonadaceae family and Pseudomonas genus. QPCR analysis suggests that the percent occupation of Pseudomonadale species to total Proteobacteria in the examined stations is close to several sampling stations close to sewage treatment plants, where consistent release of organic wastes occurred.

To evaluate the nutrient load due to the grazing of laying hens in outdoor runs, soil characteristics were monitored in three Italian organic farms. For each farm, soil samples were taken from three increasing distances from the hen house and two depths and different chemical parameters were evaluated. The comparison among the results from the different distances shows that N-NO3 and Olsen P are the most affected parameters by hen faeces: both present high values with a statistically significant difference in the area close to the poultry house and for the most superficial layer. Even TKN and TOC show significant differences between the concentrations of the first layer (more concentrated) and those of the second layer (less concentrated). In general, the surface soil layer closest to the chicken house is the portion of the outdoor run most affected by chicken droppings and represents the most critical point in terms of potential environmental impact. Therefore, it is necessary to intensify the management of the outdoor run with tools that can facilitate the grazing of animals and with vegetation that can absorb nutrients by limiting leaching and run-off.

This paper presents a novel framework for Collaborative Learning Networks (CLNs) in classrooms, aiming to optimize resource utilization and enhance educational services. The study addresses the inefficiencies of traditional education models, particularly the underutilization of computational resources and limited access to specialized software. The proposed framework employs a mix of task-based and random allocation strategies to distribute computational tasks within the CLN, considering each device’s capabilities and task requirements. The findings show significant improvement in resource utilization, facilitated by device-to-device collaboration and task sharing, thus enriching students’ learning experiences. This work contributes to optimizing resource utilization in education, advancing the field of CLNs.

Wafer-scale blue micro-light-emitting diode (micro-LED) arrays are fabricated with a pixel size of 12 μm, a pixel pitch of 15 μm, and a pixel density of 1692 pixels per inch, achieved by optimizing the properties of e-beam-deposited and sputter-deposited indium tin oxide (ITO). Although the sputter-deposited ITO (S-ITO) films exhibit a densely packed morphology and lower resistivity compared to those of the e-beam-deposited ITO (E-ITO) films, the forward voltage (VF) values of a micro-LED with the S-ITO films are higher than those with the E-ITO films. The VF values for a single pixel and for four pixels with E-ITO films are 2.82 V and 2.83 V, respectively, while the corresponding values for S-ITO films are 3.50 V and 3.52 V. This was attributed to ion bombardment damage and nitrogen vacancies in the p-GaN layer. Surprisingly, the VF variations of a single pixel and of four pixels with the optimized E-ITO spreading layer from five different regions are only 0.09 V and 0.10 V, respectively. This extremely uniform VF variation is suitable for realizing micro-LED displays to be used in AR and VR applications, circumventing the bottleneck in the development of long-lifespan and high-brightness organic LED devices for industrial mass production.

Layered halide perovskites have emerged as a promising contender in solid-state lighting thanks to their tunable bandgap, high luminescence quantum yield, and high color purity. However, the fabrication of perovskite light-emitting devices in laboratories usually experiences low de-vice-to-device reproducibility since perovskite crystallization is highly sensitive to ambient condi-tions, such as humidity and temperature. Although device processing inside gloveboxes is primarily used to reduce the influence of oxygen and moisture, several extraneous variables, including gas-eous pollution traces and thermal fluctuations in the inert atmosphere or contaminations from re-sidual solvents confined in the enclosed environment, can destabilize the crystallization process and alter the properties of the emissive layers. Here, we examine different experimental set-ups for spin-coating deposition of layered perovskites in inert atmospheres and their influences on the formation of polycrystalline thin films. Our results demonstrate that fluctuations in the glovebox properties (concentrations of residual O2 and H2O or solvent traces), even in very short timescales, can negatively impact the consistency of the perovskite film formation, while thermal variation plays a relatively minor role in this phenomenon. Furthermore, careful storage of chemical species inside the workstation is critical for reproducing high-quality perovskite layers. Consequently, when applying our most controlled environment for perovskite deposition, the photoluminescence life-time of perovskite thin films shows a standard deviation of only 3%, whereas the reference set-up yields a 15% standard deviation. Regarding complete perovskite light-emitting diodes, the uncer-tainties in statistical luminance and EQE data are significantly reduced from 230% and 140% to 38% and 42%, respectively.

Currently Single Board Computers (SBCs) are sufficiently powerful to run Real-Time Operating Systems (RTOSs) and applications with real-time attributes and requirements. SBCs serve as a foundation in Industrial Internet of Things (IIoT). The NXP Semiconductors produces a series of SBCs based on ARM-processors for a variety of industrial applications. The continuous increase in real-time data generated by IoT devices adds further research issues about the efficiency of such systems and applications. The purpose of this research was to investigate the timing performance of an NXP TWR-K70F120M device with μClinux OS on running concurrently tasks with real-time features and constraints. A custom-built multithreaded application with specific compute-intensive sorting and matrix operations was developed and applied to obtain measurements in specific timing metrics, including task’s execution time, threads waiting time, and response time, under different threads variations. The performance of this device was additionally benchmarked and validated against favorite platforms, a Raspberry Pi4 and BeagleBone AI SBCs. The experimental results showed that this device stands well both in terms of timing and efficiency metrics. Execution times were quite lower than the others, by approximately 56% in the case of two threads, and by 29% in the case of thirty-two threads configurations.

Conventional fertilization practices can lead to many ecological problems, such as nutrient imbalance, soil acidity, and reduced soil fertility in natural rubber plantations. To address these challenges, a field investigation was strategically carried out to substitute inorganic fertilizer with organic fertilizers consisted of six treatments, i.e., no fertilization (CK), inorganic fertilizer (NPK), 25 % replacement of inorganic through organic (25%M), 50 % replacement of inorganic through organic (50%M), 75 % replacement of inorganic through organic (75%M), and 100% organic fertilizer (100%M). The soil physicochemical properties (SOC, TN, AN, C:N, pH, NH4+-N, and NO3--N) and carbon and nitrogen converting enzymes (BG, NAG, and LAP) were all determined. The partial substitution of inorganic fertilizers with organic fertilizers (i.e., 75%M at surface soil layer) showed higher SOC (14.52 g.kg-1), TN (1.06 g.kg-1), AN (20.07 mg.kg-1), C:N (14.63), NH4+-N (10.63 mgkg-1), and NO3--N(11.06 mg.kg-1) than NPK and CK. Such increase in physicochemical properties in partial replacement of inorganic with organic fertilizers plots resulted from higher carbon and nitrogen enzymes activities (BG (143.17 nmol.g-1.h-1), NAG (153.96 nmol.g-1.h-1), and LAP (153.48 nmol.g-1.h-1)) compared to NPK and CK, and further the person correlation and RDA analysis confirmed a significant positive correlation between SOC, AN, and soil enzymes. This study presents a new strategy for assessing the impact of partially replacing inorganic fertilizers with organic fertilizers in rubber plantations, mainly by modifying the soil nutrient composition in tropical regions.

A series of waterborne polyurethane (WBPU)/modified lignin amine (MLA) adhesives was prepared using modified lignin amine (MLA) as a chain extender by a prepolymer mixing process. A successful Mannich reaction was achieved during the synthesis of MLA by reacting lignin with bis(3-aminopropyl)amine. Higher tensile strength, Young’s modulus and thermal stability were recorded for WBPU/MLA adhesives with higher MLA contents. The WBPU/MLA adhesive materials were used to coat PVC substrates. The adhesive strength increased with increasing MLA content. More importantly, the MLA also enhanced the WBPU/MLA coating in terms of adhesive strength at moderately high temperatures as well as under natural weather exposed conditions. The adhesive strength was essentially unaffected with 6.48 mole% MLA in the WBPU/MLA coating after exposure to natural weather conditions for 180 days.

Melasma is a challenging skin condition which involves both structural and functional skin alterations. Despite the availability of various treatment options, the management remains complex. This is the first study to investigate topical application of Rosa Damascena stem cell exosomes when used concomitantly with microneedling in women and men with facial melasma. We recruited 20 subjects with Fitzpatrick skin types I-III, exhibiting melasma of varying severity. The modified Melasma Area and Severity Index (mMASI) and Global Aesthetic Improvement Scale (GAIS) were utilized to evaluate treatment response. The treatment protocol involved microneedling followed by exosome application over four or five sessions, at 4-week intervals. Ninety percent of subjects demonstrated a significant improvement in mMASI scores, while only 10% showed no change. GAIS assessment further supports overall improvement, with just 10% categorized as "not changed". Tolerability was favorable, with mild, transient side effects. Our findings suggest promising outcomes with this combined therapy, underscoring its potential as a safe and effective approach for treating melasma, particularly in severe and moderate cases. However, further research with larger sample sizes and control arms is warranted to validate these findings and explore long-term efficacy.

In this paper, a 100CMM regenerative thermal oxidizer (RTO) system based on a high heating device for low-emission combustion is implemented at a volatile organic compound (VOCs) gas generation workplace. Existing RTO has a structure that repeats the inflow and discharge of VOCs gas into a cylindrical drum-type rotating disk and has excellent energy efficiency with a heat recovery rate of 95% or more. However, when used for a long time, there is a problem that rotation stops or explodes due to the discharge of pollutants due to dust and thermal expansion due to high temperature of 800℃. To overcome this, a RTO based on a high heating device was developed to reduce low-emission combustion emissions and energy use. Through 177 hours of demonstration time, the oxidation efficiency of VOCs was 98.87%; the waste heat recovery rate was reduced by 95.78%, the fuel consumption was reduced by 21.95%, and the nitrogen oxide concentration was 3.9 ppm

In this paper, a 100CMM regenerative thermal oxidizer (RTO) system based on a high heating device for low-emission combustion is implemented at a volatile organic compound (VOCs) gas generation workplace. Existing RTO has a structure that repeats the inflow and discharge of VOCs gas into a cylindrical drum-type rotating disk and has excellent energy efficiency with a heat recovery rate of 95% or more. However, when used for a long time, there is a problem that rotation stops or explodes due to the discharge of pollutants due to dust and thermal expansion due to high temperature of 800℃. To overcome this, a RTO based on a high heating device was developed to reduce low-emission combustion emissions and energy use. Through 177 hours of demonstration time, the oxidation efficiency of VOCs was 97.87%; the waste heat recovery rate was reduced by 95.78%, the fuel consumption was reduced by 21.95%, and the nitrogen oxide concentration was 3.9 ppm

In this study, the resource blocks (RB) are allocated to user equipment (UE) according to the evolutional algorithms for long term evolution (LTE) systems. Particle Swarm Optimization (PSO) algorithm is one of the evolutionary algorithms, based on the imitation of a flock of birds foraging behavior through learning and grouping the best experience. In previous work, the Simple Particle Swarm Optimization (SPSO) algorithm was proposed for RB allocation to enhance the throughput of Device-to-Device (D2D) communications and improve the system capacity performance. In simulation results, with less population size of M = 10, the SPSO can perform quickly convergence to sub-optimal solution in the 100^th generation and obtained sub-optimum performance with more 2 UEs than the Rand method. Genetic algorithm (GA) is one of the evolutionary algorithms, based on Darwinian models of natural selection and evolution. Therefore, we further proposed a Refined PSO (RPSO) and a novel GA to enhance the throughput of UEs and to improve the system capacity performance. Simulation results show that the proposed GA with 100 populations, in 200 generations can converge to suboptimal solutions. Therefore, with comparing with the SPSO algorithm the proposed GA and RPSO can improve system capacity performance with 1.8 and 0.4 UEs, respectively.

Candidiasis is considered an emerging public health concern because of the occurrence of drug-resistant Candida strains and the lack of available structurally diverse antifungal drug armamentariums. The indole alkaloid globospiramine from the anticandidal Philippine medicinal plant Voacanga globosa exhibits a variety of biological activities; however, its antifungal properties remain to be explored. In this study, we report the in vitro antifungal activities of globospiramine against Candida albicans and Candida tropicalis and explore its possible target proteins using in silico methods. The colony-forming unit (CFU) viability assay revealed time- and concentration-dependent anticandidal effects of the alkaloid by decreasing almost 50% of the viable CFUs 60 min after treatment. Results of the MIC and MFC assays indicated inhibitory and fungicidal effects of globospiramine against C. albicans (MIC = 8 µg/mL; MFC = 4 µg/mL) and potential fungistatic effects against C. tropicalis at lower concentrations (MIC = 4 µg/mL; MFC &gt; 64 µg/mL). The FAM-FLICA poly-caspase assay showed metacaspase activation in C. albicans cells at concentrations of 16 and 8 µg/mL, which agreed with the MIC and MFC values. Molecular docking and molecular dynamics simulation experiments indicated stable, strong binding of globospiramine with the target proteins 1,3-β-glucan synthase and Als3 adhesin enzymes, which are indirectly involved in apoptotic-driven candidal inhibition.

The market of natural and organic cosmetics has been growing in last decades. The increase in interest in this type of product is a consequence of the concern that consumers have been presenting in relation to the environment and health. In addition to the appreciation the use of sustainable ingredients in cosmetic formulations, the consumers are also concerned about pollution caused by the use of plastics, which leads industries to reinvent themselves and rethink about the composition of packaging. The factor that most drives the purchase of natural and organic cosmetics is the fact that the consumer, in addition to contributing to the preservation of the environment, is also using a sustainable product. The growing demand for natural and organic cosmetics results in a concern of the brands with the organic issue, with the decreased use of animal derived ingredients and with the updating the parameters required for certification of a cosmetic as natural or organic. Due to the few studies available in this area, the importance of clarifying the definitions and concepts of natural and organic cosmetics is evident, in order to contribute with accurate information for the cosmetic sector.

We revisit the argument that link the efficiency of a solar cell to its reverse operation as a LED, in the case where the material is organic. In organic cells, exciton transport is an intermediate process between sunlight absorption and the generation of electric current. We show that quenching exciton radiation can be beneficial to cell efficiency, without contradicting the general rule prevailing for semiconductor cells. Our treatment allows us to discuss both bulk heterojunction and planar junctions.

As cardiovascular diseases continue to be a leading cause of mortality, recent-ly, wearable devices for monitoring cardiac activity have gained much interest among medical community. This paper introduces an innovative ECG monitoring system based on a single – lead ECG machine enhanced with machine learning methods. The system only processes and analyses the ECG data, but also predict potential heart disease at an early stage. The wearable device was built on the ADS1298 and a microcontroller STM32L151xD. A server module based on REST API architecture style was designed to fa-cilitate interaction with web-based segment of the system. The module is responsible for receiving data in real time from microcontroller and their deliver to web – based segment. Algorithms for analyzing ECG signals have been developed, including band filter artifact removal, K-means clustering for signal segmentation, and PQRST analysis. Machine leaning methods as Isolation Forest have been employed for ECG anomaly detection. Moreover, a comparative analysis with various machine learning methods, including lo-gistic regression, random forest, SVM, XGBoost, decision forest and, CNNs was conducted to predict cardiovascular diseases. Convoluted Neural Networks (CNN) showed an accu-racy of 0.926, proving high effectiveness in ECG data process.

The forest regeneration phase in Sweden commonly involves mechanical soil preparation followed by planting of Scots pine or Norway spruce seedlings. The prepared soil offers planting positions with different properties, including decreased damage by pine weevil (Hylobius abietis L.). Nitrogen fertilization can be applied at the time of planting to aid establishment of the seedlings. In this study we compared the effect of organic nitrogen-fertilization for different planting positions, and seedling sizes on early survival and growth of Scots pine and Norway spruce seedlings. The main planting positions were capped mound, hinge, and mineral soil. Seedlings planted close to organic material were categorized as “low quality positions”, since proximity to organic material increase pine weevil attraction. Higher mortality rates related to pine weevil damage were recorded for seedlings planted in the low-quality positions, regardless of seedling size or N-fertilization. Pine weevil attack rates increased with increasing seedling size. Growth was in general lowest in mineral soil positions. The effect of organic N-fertilization on growth was positive for spruce regardless of planting positions and seedling size, while depending on planting position and seedling size for pine, indicating that effects of organic N-fertilization depend on seedling species, -size and planting position.

Seeds from several Ribes taxa were surveyed for phenolic compounds and in vitro antiproliferative activity against HT-29 colorectal cancer cells. Total phenolic compounds were analysed through the Folin-Ciocalteu procedure, while phenolic profiles were analysed by LC coupled to a single mass spectrometer Orbitrap using an electrospray interface (ESI). Antitumor effects were established using the MTT (3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyltetrazolium bromide) assay. Total phenolics ranged from 11.4 in R. alpinum to 94.8 mg of caffeic acid equivalents (CAE)/g in R. nigrum 'Koksa'. Concerning phenolic compounds, four were hydroxylated benzoic acids, four cinnamic acid derivatives, eight flavonoids, and nine flavonoid glycosides. The growth inhibition against HT-29 cancer cells was exercised much better by R. nigrum 'Koksa' and Ribes 'Erkeeni' (GI50 37 and 42 µg/ml). All Ribes extracts, except R. nigrum 'Hara katarlik', showed higher activity than that of R. rubrum (GI50 at 72 h: 99 µg/ml). Interestingly, the highly bioactive extract from Ribes 'Erkeeni' contains all detected phenolics, while R. nigrum 'Koksa' lacks only populnin. Therefore, the high bioactivity found for such extracts could be due to a synergy due to all detected compounds. This work constitutes a comprehensive action for expanding knowledge on the phenolic profiles and antitumor activity of GLA-rich Ribes seeds.

The article analyzes existing materials and structures with quadratic-nonlinear optical properties that can be used to generate a difference frequency in the terahertz and sub-terahertz frequency ranges. The principle of constructing a nonlinear optical-radio converter, based on an optical focon (a focusing cone), is proposed. Based on the assumption that this focon can be implemented from the metal-organic framework (MOF), we propose a technique for modeling its parameters. The mathematical model of the process of propagation and nonlinear interaction of waves inside the focon is based on a simplification of the nonlinear wave equation. Within the framework of the developed model, the following parameters are approximately determined: the 3D gradient of the linear refractive index and the function determining the geometric profile of the focon, which provide a few-mode-based generation of the difference frequency.

Biochars are often proposed as a strategy for long-term carbon sequestration. Nevertheless, application of pyrolysed feedstock, particularly along with exogenous organic matter, may affect carbon dynamics in soil through introduction of labile carbon pools and stimulation of extracellular enzymes activity. The main aim of this research was to evaluate the influence of biochars and unprocessed organic amendments addition in two agricultural soils on the dissolved organic carbon (DOC) content and activity of three enzymes involved in carbon turnover. In the incubation experiment, activity of dehydrogenase, β-glucosidase, cellulase and DOC content were measured on day 30, 60, 90, 180 and 360. Addition of biochars stimulated the activity of dehydrogenase and β-glucosidase, while cellulase was suppressed. Fresh biomass amendment enhanced activity of the enzymes through priming effect. DOC content tended to be the highest in treatments with high enzyme activity, suggesting that DOC introduced with amendments acted as a source of energy for microbes. Our findings support the hypothesis that biochar properties and presence of exogenous organic matter affect microbial response in soil, what might be crucial for carbon sequestration potential of biochar. However, long-term studies are recommended to fully understand the mechanisms that determine response of soil biota to biochar addition.

Meloidogyne nematodes, commonly known as root-knot nematodes, pose a considerable threat to crop yields, resulting in significant economic losses due to their intricate biology and limited control methods. In line with the European Union's focus on promoting organic farming and soil health to encourage sustainable agricultural practices, this study explores the efficacy of two characterized bacterial communities obtained from compost, namely SynCom1 and SynCom2, against Meloidogyne javanica in tomato plants. Through pot experiments, it is demonstrated that both bacterial communities effectively suppress nematode reproduction and root infections while simultaneously enhancing various growth parameters in tomatoes. These findings underscore the potential of synthetic bacterial communities as promising tools for organic or integrated pest management, thereby supporting sustainable agricultural practices and contributing to improved crop yields.

African scientific research faces formidable challenges, particularly with limited access to state-of-the-art measurement instruments. The high cost associated with these devices presents a significant barrier for regional research laboratories, impeding their ability to conduct sophisticated experiments and gather precise data. This predicament not only hampers the individual laboratories but also has broader implications for the African scientific community and the advancement of knowledge in developing nations—the financial cost barrier considerably impacts the research quality of these laboratories. Reflection on technical and economical solutions needs to be quickly found to help these countries advance their research. In civil Engineering, the thermal conductivity property is the most important measurement for characterising heat transfer in construction materials. Existing devices (i.e., conductometers) in a laboratory are expensive (approximately 30,000 euros) and unavailable for some African laboratories. The study proposes a new and affordable device to evaluate thermal conductivity in construction materials. The method involves establishing a thermal flux between a heat source ( from the Joule effect provided by steel wool where a current is circulating) and a cold source (generated by ice cube) under steady-state conditions. The development of the cylindrical prototype is based on the comparative flux-meter method outlined in the measuring protocol of the ASTM E1225 standard document. Experiments were conducted on four distinct materials (polystyrene, wood, agglomerated wood, and rigid foam). The results indicate a correct correlation between the experimental values obtained from the newly developed prototype and the reference values found in the literature. For example, concerning the experimental polystyrene study, the detailed case analysis reveals a good correlation, with a deviation of only 4%. The percent error found falls within the acceptable range indicated by the standards recommendations of the ASTM E1225 standard, i.e., within 5% acceptable error.

The proliferation of radio frequency devices in today's society, especially in smart homes, Internet of Things devices, and smartphones, underscores the urgent need for robust identification methods to strengthen cybersecurity. This paper delves into the field of radio frequency fingerprinting to propose a Bluetooth device identification method based on the application of the Jensen-Shannon divergence to the statistical distribution of noise in Bluetooth signals. A detailed case study is performed to investigate the Bluetooth radio frequency noise recorded at 5 Gsps from different devices is investigated to define a statistical radio frequency fingerprint for each Bluetooth device. A noise model is used to extract a unique, universal, persistent, recoverable, and robust statistical radio frequency fingerprint that identifies each Bluetooth device. Then, using the Jensen-Shannon divergence, different noise signals provided by each Bluetooth device are compared with the statistical radio frequency fingerprint of all devices and a membership resolution is declared. The study shows that the proposed method can discriminate between devices of the same brand and model, achieving an identification effectiveness of 99.5 \%. By leveraging the statistical radio frequency fingerprint of Bluetooth devices, this research not only contributes to the advancement of the field of implicit device authentication systems based on wireless communication but also provides valuable insights into the practical implementation of radio frequency identification techniques that could be useful in forensic processes.

The application of electrode-based microfluidic devices in biological entity often imposes a problem due to joule heating. The strong applied potentials or micro channels having narrow cross sections generate undesirable temperature inside the microfluidic channels leading to strong thermal distribution inside the micro channel. When intrinsic distribution of temperature, if not fix with threshold value, causes device damage or cell loss. In this work, we investigate the effects of temperature generated due to joules heating effects and we attempt to address the design constraints for minimizing the joule heating effects in the microfluidic device for developing effective microfluidic device. The device reliability was analyzed under different parametric constraints for various types of substrate materials (PDMS, PMMA, Polyimide and glass). We also attempt to investigate the effects of cell reliability due to strong temperature gradients generated through different applied potentials on different cell types. Furthermore, the response of the device performance due to different electrode configuration and different conductivity of the medium was also studied. Our investigation will eventually provide guidelines for microfluidic researchers to fabricate efficient electrode based microfluidic device which will ultimately help to choose a critical channel dimensions, threshold potentials, and conductivity of solutions in order to avoid device damage and cell loss.

Previous studies showed that some lamellarin-resembling annelated azaheterocyclic carbaldehydes and related imino adducts, sharing the 1-phenyl-5,6-dihydropyrrolo[2,1-a]isoquinoline (1-Ph-DHPIQ) scaffold, are cytotoxic in tumor cells and may reverse multidrug resistance (MDR) mediated by P-glycoprotein (P-gp). Herein, we synthesized and evaluated for their antiproliferative activity in four tumor cell lines (RD, HCT116, HeLa, A549) and ability of inhibiting P-gp-mediated MDR some ten diversely substituted 1-Ph-DHPIQ derivatives bearing at position 2 carboxylate groups (COOH, COOEt), nitriles (CN) and Mannich bases (e.g., morpholinomethyl derivatives). Lipophilicity parametrization and molecular docking calculations improved the understanding of the structure-activity relationships in cytotoxicity and P-gp inhibition of the investigated 1-Ph-DHPIQs, which led us to disclose a novel Mannich base HCl salt (8b’), which proved to be cytotoxic to all the tested tumor cell lines in the low micromolar range (IC50 &lt; 20 M) and to inhibit in-vitro the efflux pumps P-gp and MRP1 responsible for MDR, with IC50s of 0.45 and 12.1 M, respectively.

In order to address the issue of nutrient deficiency in coconut coir-based nursery substrates, three materials with nutrient supplementation effects, namely pig manure, composted rice husks, and agricultural humic acid, were added in equal volumes to the coir-based substrate. The newly formulated substrates were then tested for their seedling growth effects on cucumber and rice. Results indicate that the substrate formulation consisting of "10% pig manure + 30% peat + 50% coconut coir + 10% vermiculite" was capable of satisfying the growth requirements of both cucumber and rice seedlings, with the highest acceptance among farmers.

Industrial hemp (Cannabis sativa L.) is an attractive candidate for sustainable pest management due to its abundance of bioactive compounds with potential pesticidal properties. Solvent choice has a significant impact on the extraction efficiency of bioactive compounds. Deep Eutectic Solvents (DESs) are gaining popularity in extraction because they are safe and environmentally friendly, making them viable alternatives to organic solvents (OSs). This research first compared the extraction efficiency of OSs on the extraction of phytochemicals from the infloresences of two hemp varieties, Citrus and Cherry Dwarf. Inflorescences were extracted using three OSs, ethanol, ethyl acetate, and hexane. The highest level of cannabidiol (CBD; 0.69%) was extracted from Cherry Dwarf using ethanol while the level of delta-9 tetrahydrocannabinol THC (0.19%) was essentially the same in both. Therefore, Cherry Dwarf was selected to compare the extraction efficiency of DESs to the OSs. The DESs were choline chloride/ethylene glycol, citric acid/ethylene glycol, menthol/lauric acid, choline chloride/urea and choline chloride/glycerol. In the targeted analysis, choline chloride/ethylene glycol extracted the highest amount of CBD (0.87%) followed by choline chloride/urea (0.78%). As some DESs outperformed ethanol, the popular solvent for extracting cannabinoids, DESs are viable candidates to replace organic solvents.

Phase Change Materials (PCMs) are latent heat storage media with high potential of integration in building structures and technical systems. Their solid-liquid transition is commonly utilized for thermal energy storage in building applications. It also means that some kind of encapsulation is necessary. This is often solved with metal containers that also have high thermal conductivity and resistance to mechanical damage enhancing the performance these so called latent heat thermal energy storage (LHTES) systems. However selection of suitable metal is rather challenging. It depends, among other things, on the elimination of undesirable interaction between storage medium and surrounding metal. Heat storage medium must be reliably sealed in metal container especially when the storage system is integrated in systems like domestic hot water storage tanks, where PCM leaks can negatively affect human health. The aim of this study was evaluation of interaction between selected commercially available organic and inorganic PCMs and metals. The evaluation is based on the calculation of corrosion rate and use gravimetric method for determination of the weigh variations of the metal samples. Results show that aluminium is the most suitable container material with lowest mass loss and suffered only minimal visual changes on the surface after prolonged exposure to PCMs.

Starting 1994, the debate for regulating organic agriculture in Brazil was officially recognized in May 1999. Still, only in 2003, when the law # 10,831 was instituted, the country reached an effective milestone on organic production, both internally and externally. Since the industry regulation, the legislation underwent many modifications, constantly reviewing and adjusting. The current study examined the institutionalization of organic production in Brazil and what the current regulations can be used as a reference for those interested in this sector. The most recent update of Organic legislation and its implication on practice were also discussed. A case study on production of strawberry in organic system is presented and discussed.

The climate change is likely to modify the freezing-thawing cycles in soils and surface waters of permafrost-affected and subarctic regions. Yet, the change of solution chemical composition during ice formation and evolution of remaining fluids remain very poorly known. Towards better understanding of dissolved (&lt; 0.45 µm) organic carbon, major and trace elements behavior in permafrost peatland environments, here we performed laboratory freezing of peat leachates, from complete freezing to complete thawing in order to quantify the partitioning of solutes between the aqueous solution and the remaining ice. We hypothesized the existence of two main groups of solutes, behaving conservatively or non-conservatively during freezing depending on their incorporation into the ice or ability to coagulate in the form of insoluble minerals or amorphous materials in the fluid phase. An unexpected result of this work was that, despite sizable degree of element concentration in the remaining fluid and possible coagulation of organic, organo-mineral and inorganic compounds, the freezing and subsequent thawing produced the final concentrations of most solutes which were not drastically different from initial concentrations in starting leachates, prior freezing. This demonstrates high stability of dissolved (&lt; 0.45 µm) OC, Fe, Al and some trace metals to repetitive freezing and thawing of surface waters in permafrost peatlands.

Glucose is a simple sugar molecule. The sugar molecule is chemically symbolised as C6H12O6. This means that the glucose molecule contains 6 carbon atoms (C), 12 hydrogen atoms (H) and 6 oxygen atoms (O). In human blood, the molecule glucose circulates as blood sugar. Normally after eating or drinking, our body breaks down the sugars in food and uses them to obtain energy for our cells. To do this, our pancreas produces insulin. Insulin "pulls" sugar from the blood and puts it into the cells for use. If someone has diabetes, their pancreas can't produce enough insulin. As a result, the level of glucose in the blood rises. This can lead one to many potential complications, including blindness, disease, nerve damage, amputation, stroke, heart attack and damage to blood vessels etc. In this study, a non-invasive method for monitoring blood glucose has been developed and is therefore easily usable. The device developed can measure the glucose level continuously and eliminates the disadvantages of the invasive system. Near-IR sensors (optical sensors) were used to estimate the concentration of glucose in the blood; these sensors have a wavelength of 940 nm. The sensor is placed on the tip of the finger and the output of the optical sensor is then connected to the microcontroller at the analogue input. Another sensor used, but only to provide more medical information was the heartbeat sensor. After processing and regression analysis, the glucose level is predicted, and data is sent via the Bluetooth network to a developed APP. The results of the implemented device were compared with available invasive methods. The study consists of a hardware platform inserted into an armband and then a small black parallelepiped-shaped box in which the optical sensors are inserted. The hardware consists of a microcontroller, a Near-IR optical sensor, a heartbeat sensor and a Bluetooth module.

Vacuum pump wear is the most prevalent failure mode of the IBA Synthera® automated radiochemistry system. Rebuilding or replacing the pump causes equipment downtime and increases the radiation exposure of the service personnel. We built a dedicated test device to assess new or rebuilt pumps prior to installation, thus reducing downtime and radiation exposure during repairs. The Testbed incorporates a microprocessor that actuates the pump, valves, pressure sensor, and communicates with the user through lights, buttons, and an alphanumeric screen. The Testbed increases productivity and safety in the radiochemistry laboratory.

Thermoelectrics, in particular solid-state conversion of heat to electricity and vice versa, is expected to be a key energy harvesting and temperature management solution in coming years. There has been a resurgence in the search for new materials for advanced thermoelectric energy conversion applications and to enhance the properties of existing materials. In this paper, we review recent efforts on improving figure-of-merit (ZT) through alloying and nano structuring. As heatsink characteristics dictate the performance of thermoelectric modules, various types of heatsink designs has been investigated. Several reported strategies for improving ZT are critically assessed. A notable increase in figure-of-merit of thermoelectric materials (TE) has opened up new areas of applications especially in the medical field. Peltier cooling devices are widely employed for patient core temperature control, skin cooling, medical device and laboratory equipment cooling. Application of these devices in the medical field both in temperature control and power generation has been studied in detail. It is envisioned that this study will provide profound knowledge on the thermoelectric based materials and its role in medical applications.

This paper presents a device for measuring and maintaining the constant water level in a tank. The device uses a capacity sensor to measure the water level. The sensor has a DC voltage output proportional to the water level in the tank. This voltage can be used in other automation too. The water level, in percentages, is displayed on a vu meter with 8 LEDs. The circuit for maintaining the constant level consists in a comparator with hysteresis. The level of the water is adjustable, using a reference voltage from a potentiometer (marked in percentages). The level of the water is compared with the prescribed level and the difference between them commands the start/stop of the water pump which supplies the tank through a relay. The device is powered by 220 V and is isolated from the environment.

Rising organic charge in northern freshwaters is attributed to increasing levels of Dissolved Natural Organic Matter (DNOM) and shifts in water chemistry. Organic charge concentration may be determined by charge balance calculations (Org.-) or modelled (OAN-) using the conceptual Oliver and Hruška models based on the density of weak acid functional sites (SD) present in DNOM. The charge density (CD) is governed by the SD and protonation and complexation reactions on the functional groups. The models use this SD as a key parameter in empirically fitting the model to Org.-. Utilizing extensive datasets of water chemistry, this study shows that spatial and temporal differences in SD and CD are influenced by variations in the humic-to-fulvic ratio of DNOM and the organic aluminum (Al) complexation, as well as the mole fraction of CD to SD governed by the acidity. Site median SD obtained for 44 long-term monitored acid-sensitive lakes was 11.1 and 13.9 µEq/mg C for the Oliver and the Hruška model, respectively. During the 34 years of monitoring the CD increased by 70%, likely due to rising pH and declining Al complexation with DNOM. Present-day median SD values for the Oliver and Hruška models in 16 low-order streams are 13.8 and 15.8 µEq/mg C, respectively, and 10.8 and 12.5 µEq/mg C, respectively, in 10 high order rivers.

Even in the first quarter of XXI century, the presence of organic dyes in wastewaters is a normal occurrence in a series of countries, and being these compounds toxics, their removal from these waters is of a necessity. Among the separation technologies, adsorption processing appeared as one of the most widely used to reach this goal. The present work reviewed the most recent approaches (first half of 2021 year) about the use of a variety of adsorbents on the removal of, also, a variety of organic dyes of different nature.

The European Union green deal has proposed the “organic farming action plan” to render this farming system more sustainable for climate mitigation and adaptation and to meet the United Nations Sustainable Development Goals (UN-SDGs). While this policy instrument is fundamental to reach sustainable agriculture, there is still no agreement on what sustainable agriculture is and how to measure it. This opinion paper proposes an ecosystem-based framework on the crop life-cycle to determine the balance between economic, social and environmental pillars of sustainability to support decision-making.

The soil organic matter (SOM) content and stability in natural gypsum soils and soils from mining/industrial areas were compared, in terms of their physical, chemical and micromorphological properties, to determine whether the old brownfield soils were acting as carbon (C) sinks, counteracting increasing carbon dioxide concentrations in the atmosphere. The mining/industrial soils were 50–400 years old, so had been left sufficiently long for full self-restoration. Despite having very different origins, both natural and brownfield soils stored similar amounts of SOM, and had similar pH values, calcium carbonate contents and textures. They were also fully covered with similar grass plant communities. The mining/industrial soils exhibited similar microstructures to the gypsum soils and were often quite porous. The most striking difference between them and the natural gypsum soils was that the mining/industrial soils were strongly polluted with zinc, lead and cadmium. The 50-year-old brownfield soils differed from the others in terms of having a lower state of SOM transformation, with a much higher C/N ratio, lower aggregate water resistance index, lower dehydrogenase activity and greater areas of undecomposed or slightly decomposed plant residues. These parameters in the older (150–400 years) brownfield soils were similar to those of the natural soils.

Abstract: Windtech device is a novel tool for measuring the sensation of the ‘cold’. Cold poses numerous challenges for industrial operations, human survival, and living convenience. The impact of the cold is not possible to be quantified just based on temperatures; however other factors such as wind speed, humidity, irradiance have to be taken into consideration. Efforts have been made to develop combined indices such as wind chill temperature (WCT), AccuWeather RealFeel®, and others. The presented article discusses these along with the industrial standards that emphasize on the quantification of the ‘cold’. The following article introduces the Windtech device and its operating principle involving ‘heated temperature’, where the ‘heated temperature’ is affected by environmental parameters including ambient temperature, humidity, wind velocity, and irradiance. The discussed Windtech device is calibrated for operation according to the ISO 11079:2007 standard.

Dissolved organic matter (DOM) in the ocean represents about 662 billion tonnes of C, 200 times more than the living biomass. It is produced mainly by microbial primary production. The largest fraction of this DOM is old (>weeks to months) and both chemically and biologically recalcitrant. The remainder is young (seconds to weeks), more labile and surface active. It also changes the rheological properties in the bulk phase of the water and at interfaces including the sea surface microlayer (SML). In order of abundance, this DOM consists of sugars, amino acids, fatty acids and nucleic acids, often incorporated into complex polymers. The DOM molecules are produced by microbial genes, and are further modified by enzymes themselves produced by genes. The properties of ocean water and its interfaces as well as biogeochemical fluxes may thus be modified by ocean microbial genes. These fluxes influence ocean and atmospheric climate, which in return acts on the biota. Therefore the ocean microbial genomes and the fluxes and climates they influence may be subject to Darwinian-type selection. Research programmes need to integrate ocean ecology, rheology, biogeochemistry and genomics, to find the associations among them. Discovery of commercial bioactive molecules may be a bonus.

To substitute of conventional manure and peat with alternatives sourcing from environmental conservation concerns, several promising alternatives has been attracting scientific parties’ interest, recently. However, among them compost perform the best, mostly and support carbon sequestration and mitigation against climate change. The article describes the made locally produced 70% in volume olive pruning branches compost (COMP) performance in two trials as an organic amendment in pepper production and an olive sapling substrate during 2019-2021 organic management in Turkey. The application of COMP to pepper trial conducted using factorial randomised block design with 4 replications and 6 treatments increased total organic matter and soil organic carbon, significantly (p<0.05) as compared to non-used plots in two locations. The olive sapling trial was conducted using a randomised plot design with 4 replications and 4 treatments. After the 12 months of growth, compost had the largest architecture rooted plants significantly different (p<0.05). Fresh volume (cm³) of COMP used saplings were obtained 35% less than 40% peat treatment, significantly (p<0.05) while 6^th month measurement was found as 40%. It is concluded that to enhance circular economy recycling and composting olive pruning branches is lucrative for the country to reduce external input usage in organic horticultural production.

Is the production of the “AnchoisFert” organic fertilizer via the circular economy process based on omega-3 lipid extraction of milled anchovy fillet leftovers with citrus limonene followed by mild drying economically and technically viable? This study answers this question and identifies the main obstacles, chiefly of economic and organizational nature, to be overcome prior to commercialization of this new organic fertilizer. Along with non-variable and proven efficacy, successful competition with conventional organic and inorganic fertilizers requires affordable cost and regular supply. This, inter alia, requires to establish new and mutually beneficial relationship between bioeconomy firms and fish processing companies.

The combination of organic matter, iron oxide, and clay minerals is of great significance for the adsorption of copper ions (Cu). The purpose of this study is to explore the characteristics of Cu adsorption and laws governing Cu complexation to organic–inorganic, organic–clay mineral, and iron-oxide–clay mineral complexes in the sediments in the estuary of plateau fault and sinking lake——Dianchi Lake. In this study, Cu adsorption tests were performed on the three complexes, in order to study the kinetic behavior of adsorption, Langmuir and Freundlich isotherm models were used. The samples before and after adsorption were characterized via scanning electron microscope (SEM), Fourier infrared spectroscopy (FTIR), and X-ray diffraction (XRD). Our results show that, the Freundlich isotherm models model was able to describe adsorbent behavior in comparison to the Langmuir models. During the Cu adsorption process, the iron-oxide–clay mineral complex is able to adsorb Cu, via coordination exchange, through the –OH contained therein. Organic-matter–clay mineral complexes bonded to the surfaces of clay minerals by replacing the hydroxyl groups with functional groups (carboxyl groups or phenolic hydroxyl groups) contained in the organic matter. Organic–inorganic composites then adsorbed Cu through the coordination exchange of –OH in the polar functional groups of alcohols, phenols, and carboxylic acids. The adsorption capacity of Cu in these three sediment complexes was observed to have the following order: organic–inorganic complex &gt; organic-matter–clay mineral complex &gt; iron-oxide–clay mineral complex. The semi-quantitative analysis results of Fourier Infrared Spectroscopy show that the organic matter (changes in the peak area of functional groups such as carboxyl groups) in the organic-inorganic composite material has an important effect on the amount of copper ions adsorbed by clay minerals.

Ankle joint flexion and extension exercises play an important role in the rehabilitation training of patients who have been injured or bedridden for a long time before and after surgery. Accurately guiding patients to perform ankle flexion and extension exercises can significantly reduce deep vein thromboembolism. Currently, most ankle rehabilitation devices focus on assisting patients with ankle flexion and extension movements, and there is a lack of devices for effectively monitoring these movements. In this study, we designed an ankle joint flexion and extension movement monitoring device based on a pressure sensor. It is composed of an STM32 microcontroller, a pressure sensor, an HX711A/D conversion chip, and an ESP8266 WiFi communication module. The value of force and effective number of ankle joint flexion and extension movements were obtained. An experimental device was designed to verify the accuracy of the system. The results showed that the device can effectively monitor and control ankle flexion and extension movements remotely, ultimately ensuring that the patient can effectively monitor and grasp the active ankle pump movement.

(1) Introduction: External high volume extraction devices may offer a way to reduce any aerosol particulate generated. The aim of this study was to measure the particle count during dental aerosol procedures and compare the results to when a High Volume Extraction device is used; (2) Methods: A comparative clinical study measuring the amount of PM1, PM2.5 and PM10 aerosol particulate with and without the use of an external High Volume Extraction device was undertaken. In total, 10 restorative procedures were monitored with an an industrial Trotec PC220 particle counter. The air sampler was placed at the average working distance of the clinicians involved in the study - 420mm.; (3) Results: In the present study aerosol particulate was recorded at statistically significantly increased levels during dental procedures without an external high volume extraction device versus with the device. The null hypothesis was rejected, in that significant differences were found between the results of the amount of aerosol particle count with and without a High Volume Extraction device.; (4) Conclusion: If the results of the present study are repeated in an in vivo setting, an external high volume suction device may potentially lower the risk of transmission of viral particulate.

This paper introduces a theory for the evolution of corporates in which the growth and sustainability strategies are developed simultaneously. Since the introduction of corporate sustainability, it has been an extra cost for risk mitigation and making ‘compensating’ positive impact. The world has reached a tipping point of volatility, mainly due to climate change but also by emergence of COVID-19, so that the applicability of existing corporate structures is under question and these poses high risk to the existence of our planet. On the other hand, the technology cost for sustainable investment has reached a parity in comparison with non-sustainable alternatives. Therefore, our proposed Organic Grow Theory introduces a step-by-step approach so that corporates can grow and be profitable without compromising the ability of future generations to meet their needs. It is concluded that, a new structure for corporate, called Founcorp, would be needed to direct corporates to evolve being a responsible legal entity.

Six mode shapes, including bending and torsion, were documented for five different basketball rims and backboards at the United States Military Academy, West Point, New York, USA. The frequency and damping ratio of each mode shape were also determined. The empirical process began with the time-domain excitation and response of each rim-backboard system. The impulse of excitation came from an impact hammer separately applied to sequentially, to each node. The sinusoidal response was gathered from an accelerometer at a fixed location, node 1. Each time-domain excitation-response was then converted to a frequency domain Bode plot for each node by a B&K 2034 Signal Analyzer, giving transfer functions of output/input versus frequency. Structural Measurements System (SMS) Software was used to fit mode shapes to the Bode plots. Each of the six mode shapes were fitted to the Bode plots of each node at a specific modal frequency. Each of the six mode shapes were a function of the locations of the nodes, and the Bode plot gathered at each node. The first and second modes were critical for showing that the Energy Rebound Testing Device statistically correlated with the energy transferred to the rim and backboard. A known perturbation mass was selectively attached to the rim, to help isolate the dynamic masses and spring rates for the rim and backboard, to ascertain the kinetic energy transferred to the rim had a 95.67% inverse correlation with rim stiffness.

The present study aimed at investigating the in vitro and in vivo susceptibility of malaria parasites to crude extracts and fractions from Polyalthia suaveolens, Uvaria angolensis, and Monodora tenuifolia. The ethanolic extracts were prepared by maceration, and were further partitioned using water, dichloromethane, hexane, and methanol. The most promising fraction was subjected to column chromatography and the sub-fractions tested for activity in vitro. The antiplasmodial effect of extracts and fractions was tested against the Chloroquine resistant (PfK1) strain in 96 wells microtiter plate format using SYBR green florescence assay. The promising fraction was further assessed for cytotoxicity and acute toxicity in Swiss albino mice and subsequently against the rodent malaria parasite, P. berghei. Qualitative phytochemical screening was also performed on the promising fraction. The methanol fractions exerted the overall better effect with that of the twigs of P. suaveolens (PStw(Ace)) showing the highest potency with a IC50 value of 3.24 µg/mL followed by the fractions of leaf of M. tenuifolia (MoTel(Ace), IC50= 3.84 µg/ml) and stem bark of P. suaveolens (IC50= 4.90 µg/ml). The phytochemical screening showed the presence of alkaloids, lactones, and phenols in the more active fraction of P. suaveolens (PStw(Ace)). The chromatographic fractionation of this fraction led to 12 sub-fractions with PS8 sub-fraction being the most active (IC50= 4.42 µg/mL). In vivo, oral administration of 2000 mg/kg b.w of fraction PStw(Ace) in mice showed no signs of toxicity. Also, fraction PStw(Ace) at 400 mg/kg b.w exerted the highest suppressive effect against P. berghei strain B throughout the 4 days experiment (% parasitaemia below 5.2%). Overall, the results achieved supported the use of the three plants in the traditional treatment of malaria in Cameroon. More interestingly, the methanolic fraction of the twigs extract from P. suaveolens might be of interest in future development of an antimalarial phytodrug.

Radical reactions in water or aqueous media are important for organic synthesis, realizing high yielding processes under non-toxic and environmentally friendly conditions. This overview includes (i) a general introduction to organic chemistry in water and aqueous media, (ii) synthetic approaches in-, on- and with-water as well as in heterogeneous phase, (iii) reaction of carbon-centered radicals with water (or deuterium oxide) activated through coordination with various Lewis acids, (iv) photocatalysis in water and aqueous media, and (v) synthetic applications bioinspired from naturally occurring processes. A wide range of chemical processes and synthetic strategies under different experimental conditions have been reviewed that lead to important functional group translocation and transformation reactions, leading to the preparation of complex molecules. These results reveal how water as a solvent/medium/reagent in radical chemistry has matured over the last two decades and how further discoveries are foreseen to come in the near future.

Waste management is a significant issue that Indonesia must face. The presence of waste will always exist as long as life continues. One of the main challenges in waste management is the proper separation of organic and inorganic waste. As a solution to address this issue, the Ministry of Environment has made efforts to develop Waste Banks. However, it also creates new problems related to manual data collection, lack of monitoring by the community in implementing waste management activities, and a lack of specific reports regarding waste management conducted by officers. We propose the creation of a website using the Agile Development SDLC method. This website involve several steps and incorporate functions for data digitalization and expedited data collection, such as the addition of QR Code functionality, Monthly Reporting Function, and enhanced data security. The method used in this research is Agile Development. The application has been developed with a user-friendly interface and the latest web development technologies to ensure smooth performance. Overall, the web-based application for organic and inorganic waste using Laravel is an important step to promoting sustainable waste management practices.

Photovoltaic is one of the promising renewable sources of power to meet the future challenge of energy need. Organic and perovskite thin film solar cells are an emerging cost-effective photovoltaic technology because of low-cost manufacturing processing and a light-weight. The main barrier of commercial use of organic and perovskite solar cells is the poor stability of devices. Encapsulation of these photovoltaic devices is one of the best ways to address this stability issue and enhance the device lifetime by employing materials and structures that possess high barrier performance for oxygen and moisture. The aim of this review paper is to find different encapsulation materials and techniques for perovskite and organic solar cells according to the present understanding of reliability issues. It discusses the available encapsulate materials and their utility in limiting chemicals such as water vapour, oxygen penetration. It also covers the mechanisms of mechanical degradation within the individual layers and solar cell as a whole, and possible obstacles to their application in both organic and perovskite solar cells. The contemporary understanding of these degradation mechanisms, their interplay and their initiating factors (both internal and external) are also discussed.

A selective permeable membrane between two different solutions can generate osmotic pressure, Donnan potential, and ion/pH gradients based on various factors such as membrane type, solute concentration and temperature. In this study, we introduce a novel method for extracting energy from ion gradients through an innovative cycle, presenting intriguing experimental findings. Additionally, by leveraging Raoult’s Law, which describes the relationship between vapor pressure and solute presence, in conjunction with osmosis within a closed system, we successfully engineer the simplest iteration of Maxwell’s demon device. This pioneering approach to sustainable energy generation harnesses ambient temperature marking a significant advancement in energy research. Finally this renewable energy source is available all the time and everywhere.

We compare two methods for creating a microfluidic device from an initial positive master with the same surface relief as the final device. The first method uses urethane or epoxy resin to create an intermediate master for PDMS casting. This method has a very low failure rate but a longer processing time. The second method utilizes PDMS double casting where the intermediate master is passivated PDMS. This method has a higher failure rate but a significantly shorter processing time. Detailed methodology for both methods is included along with a comparison of the strengths and weaknesses of each method. The resin intermediate is a simpler method while PDMS double casting is faster and more scalable. Ultimately it is found that PDMS double casting is preferable in most situations.

Cellular response to mechanical stimuli is a crucial factor for maintaining cell homeostasis. The interaction between extracellular matrix and mechanical stress plays a significant role in organ-izing the cytoskeleton and aligning cells. Tools that apply mechanical forces to cells and tissues, as well as those capable of measuring the mechanical properties of biological cells, have greatly contributed to our understanding of fundamental mechanobiology. These tools have been exten-sively employed to unveil the substantial influence of mechanical cues on the development and progression of various diseases. In this report, we present an economical and high-performance uniaxial cell stretching device. This paper reports the detailed operation concept of the device, ex-perimental design, and characterization. The device was tested with MDA-MB-231 breast cancer cells. Experimental results agree well with previously documented morphological changes re-sulting from stretching forces on cancer cells. Remarkably, our new device demonstrates compa-rable cellular changes within a 30-minute compared to the previous 2-hour stretching duration. Moreover, the device design incorporates an open-source software interface, facilitating conven-ient parameter adjustments such as strain, stretching speed, frequency, and duration. Its versatil-ity enables seamless integration with various optical microscopes, thereby yielding novel insights into the realm of mechanobiology.

We investigated new anodic coloring materials that are used as ion storage layers in complementary energy storage electrochromic devices (ESECDs) to enhance their electrochromic storage performance. In this study, we fabricated counter electrodes (ion storage layers) using IrO2 doping NiO (Ir: NiO) film through cathodic arc plasma (CAP) with varying surface charge capacities. We investigated the influence of MoO3-doped WO3 (Mo: WO3) film by various Ar/O2 gas flow ratios (1/4, 1/5, and 1/6). The ESECDs used in the demonstration were 10×10 cm2 in size. They achieved optical transmittance modulation of Ir: NiO- ESECDs (glass/ITO/ Mo: WO3/gel-polymer electrolytes/ Ir: NiO /ITO/glass), ΔT=53.3% (from Tbleaching (66.6%) to Tcoloration (13.1%)). The ESECDs had a quick coloration time of 3.58 seconds, a rapid bleaching time of 1.24 seconds, and high cycling durability. It remained at 45% transmittance modulation even after 3000 cycles. New anodic materials can provide an alternative to traditional active materials for bi-functional electrochromic batteries.

This paper describes the design and development of an active device that was applied to shoulder rotation rehabilitation. It implements a force control in a similar way to the haptic devices that reflect a force on the user’s hand according to the rehabilitation parameters. This device was tested with patients, combining clinician manipulation and programmed exercises. The results were excellent, given that the range of movement of the shoulder increased in most of the pa-tients. The results of the Usability Scale questionnaire were also promising.

Ultrasound is a well-known tool to produce thermal and non-thermal effects on cells and tissues. These effects require a correct application of ultrasound in terms of localization and acoustic energy delivered. This article describes a new device that combines ultrasound and Dry Needling treatments. The ultrasound transducer can rotate in 3D space mechanically to align itself in the direction of the needle. The transducer electronically focuses the acoustic pressure automatically on the needle tip and its surroundings. A computer, using graphical interface software, controls the angulation of the array and the focus position.

In this paper, we investigate the relationship people have with their smart devices. We use the concept of agency to capture aspects of users’ sense of mastery as they relate to their device. This study gives preliminary evidence of the existence of two independent dimensions of agency for modeling the interaction between humans and smart devices: (i) user agency and (ii) device agency. These constructs emerged from an exploratory factorial analysis conducted on a survey data collected from 587 participants. In addition, we investigate the correlation between user agency and device agency with background variables of the respondents. Finally, we argue that mapping the users’ dynamics with their device into user agency and device agency fosters a better understanding of the needs of the users and helps in designing interfaces tailored for the specific capabilities and expectations of the users.

This study investigated the effects of exogenous gibberellic acid (GA) treatments (elongating cluster + seedless + expanding, T1; seedless + expanding, T2; expanding, T3 and water, CK) on the content of sugars, organic acids, and endogenous hormones and sink strength.Results showed that T2 treatment displayed the highest fructose and glucose levels at 100 days after treatment (DAT), whereas its effect on tartaric acid, malic acid, and citric acid concentrations at 80 and 100 DAT was relatively weak. Under GA3 treatments, both GA3, IAA, and CTK contents increased, whereas ABA contents decreased at 1, 2, 4, 8, and 48 h. Analysis of sugar phloem unloading revealed that T2 treatment exhibited the highest values during softening and ripening stages. Our findings indicate that appropriate GA3 application can positively influence sink strength by regulating sink size and activity, including berry size enlargement, sugar phloem unloading and sugar accumulation in grape sink cells.

The purpose of this article is to present an IoT architecture implemented in an intelligent environment, focusing on the optimization of initial conditions and device management. A general control system was developed using an open-source platform, integrating aWi-Fi network and YAML coding to enable communication and control of the IoT architecture devices. The implementation includes actuators, sensors, and control devices that, through a graphical interface, allow the visualization of the historical record of activities and real-time measurements of connected devices. The design includes specific mechanisms and the analysis of materials through tensile tests on specimens, following the ASTM E8 standard, and deformation test simulations, in which PLA demonstrated better performance compared to materials like ABS and resin. The significance of the implemented IoT system lies in an energy saving of 58% compared to conventional structures. Additionally, the study of response times for network connections showed that using an Ethernet cable resulted in a response time of 1.21 seconds, representing a reduction of 1.65 seconds compared to the second lowest value obtained.

This research, which focuses on wave energy generating technology, suggests a brand-new oscillating float-type wave energy conversion system that is appropriate for the offshore wave environment. To accurately model the device, a three-dimensional viscous numerical pool is created based on STAR-CCM+. The array-type power generation device is numerically simulated using theoretical analysis and numerical simulation, and the wave energy power generation device is arranged as double floats in the front and rear rows, representing triangular array type and rectangular array type, respectively. The triangular array type is a superior layout and can make greater use of marine resources, according to this paper's analysis of the hydrodynamic and power generation impacts of the three array types. The findings are meant to serve as a guide for engineering practice.

The role of circulating plasma cells (CPCs) and circulating leukemic cells (CLCs) as biomarkers for several blood cancers, such as multiple myeloma and leukemia, respectively, have recently been reported. These markers can be attractive due to the minimally invasive nature of their acquisition through a blood draw (i.e., liquid biopsy) negating the need for painful bone marrow biopsies. CPCs or CLCs can be used for cellular/molecular analyses, such as immunophenotyping or fluorescence in situ hybridization (FISH). FISH, which is typically carried out on slides involving complex workflows, becomes problematic when operating on CLCs or CPCs due to their relatively modest numbers. Here, we present a microfluidic device for characterizing CPCs and CLCs enriched from peripheral blood using immunofluorescence or FISH. The microfluidic possessed an array of cross-channels (2-4 µm in depth and width) that interconnected a series of input and output fluidic channels. Placing a cover plate over the device formed microtraps, the size of which was defined by the width and depth of the cross-channels. This microfluidic chip allowed for automating immunofluorescence and FISH requiring the use of small volumes of reagents, such as antibodies and probes, as compared to slide-based immunophenotyping and FISH. In addition, the device could secure FISH results in <4 h compared to 2-3 d for conventional FISH.

A new circuit model of the self-powered device for heart rate measurement is presented in this paper. This device consists of piezoelectric energy harvester (PEH), power management circuit (PMC) with energy storage, microcontroller, Photoplethysmography (PPG) sensor, and Wi-Fi module. The PEH is placed under the insole to harvest the pressure energy from human foot-step to generate ac power. In our model, a PEH is represented by sine voltage source, where its parameters were taken from experiments with 20 volunteers. The PMC is simplified by a switch with gain δ placed in series with the main circuit. The model of the main circuit is RC elements in parallel, where C is the capacitance of the storage device, and R is the equivalent parallel resistance of the microcontroller, PPG sensor, and Wi-Fi modules, respectively. The value of R depends on the power and current absorbed by those modules during sleep, deep sleep, sense, and transmit modes which collected from the datasheet. Finally, the proposed circuit model of the self-powered device was built and simulated in SPICE. The simulation results were compared with the laboratory experiment using commercial devices. Based on the results, the proposed model had small gaps compared to the real self-powered devices in terms of average current, voltage, power and efficiency.

MEMS (Micro-electromechanical Systems) becomes important increasingly due to the smarter and smaller fuze used in OICW (Objective Individual Combat Weapon). MEMS Safety and Arming (S&A) device is employed in different platforms and regions for small caliber projectile. Therefore, it is necessary to make a parametric study of the MEMS S&A device in different apply environments and explore the main sensitive factors of the MEMS S&A device to provide reference for designs. In this paper, based on the MEMS S&A device designed by our term, theory and finite element models are established, and the centrifugal insurance mechanism of the MEMS S&A device is parametric studied under the different speeds, temperature and thickness of the model by nonlinear dynamic method. By comparing the experimental and predicted results, the established FEM model is verified, and the conclusion is that the temperature and the centrifugal force are the main sensitive factors in the centrifugal insurance mechanism. In summary, we can suggest that the application environment, which the MEMS S&A device is suitable for, is the temperature equal to or slightly greater than normal temperature and the rotating speed higher than35000r/min of small caliber projectile.

Empirically based modeling is an essential aspect of design for a wave energy converter. These models are used in structural, mechanical and control design processes, as well as for performance prediction. The design of experiments and methods used to produce models from collected data have a strong impact on the quality of the model. This study considers the system identification and model validation process based on data collected from a wave tank test of a model-scale wave energy converter. Experimental design and data processing techniques based on general system identification procedures are discussed and compared with the practices often followed for wave tank testing. The general system identification processes are shown to have a number of advantages. The experimental data is then used to produce multiple models for the dynamics of the device. These models are validated and their performance is compared against one and other. While most models of wave energy converters use a formulation with wave elevation as an input, this study shows that a model using a hull pressure sensor to incorporate the wave excitation phenomenon has better accuracy.

A series of D–π–A diketopyrrolopyrrole (DPP)-based small molecules have been designed for organic light-emitting diodes (OLEDs) and organic solar cells (OSCs) applications. Appling the PBE0/6-31G(d,p) method, the ground state geometry and relevant electronic properties were investigated. The first excited singlet state geometry and the absorption and fluorescent spectra were simulated at the TD-PBE0/6-31G(d,p) level. The calculated results reveal that the photophysical properties are affected through the introduction of different end groups. Furthermore, the electronic transitions corresponding to absorption and emission exhibit intramolecular charge transfer feature. It was disclosed that the designed molecules act not only as luminescent for OLEDs, but also donor materials in OSCs. Moreover, they also can be used as potential electron transfer materials using for OLEDs and OSCs.

In order to meet the military requirements of the fuze, such as precision strike, efficient mutilates ability and low collateral damages, the microminiaturization is an inevitable trend of secure system. Based on the silicon-based MEMS S&A device designed by our term, the design principles of each module and fabrication process are introduced. The average fracture strength and Young's modulus of the silicon are 726 MPa and 175 GPa from the tensile test, respectively. From Hopkinson impact experiment, we can get the threshold-value judging mechanism being safety under the impact overload of 20526 g, and this value is much more than the standard of the drop overload 12000g; the arming value under the centrifugal overload obtained from theory, simulation and experiment is at the range of 28200 g and 32000 g, it shows that the threshold-value judging mechanism can be arming compared with the value 35951g of design principle. Therefore, the threshold-value judging mechanism can meet the design requirements of overload. Furthermore, the relationship of fracture threshold-values obtained by different theories is found out through parametric design method, as shown in Figure 14, it provides the theory evidence to the follow parametric design.

Supramolecular structures with specific applications are a pillar in several areas of science. Thus, from a contemporary point of view, there are several reasons to feel inclined to cover a systematic, or historic critique of the supramolecular concept itself. First, the idea of a supramolecular material seems more secure now than it was decades ago. Second, updating the interacting of MOFs and supramolecular chemical and conversely, supramolecularity to assemble MOFs and to make ef-ficient complex systems in multiple cutting-edge applications. Third, we should here simply confine to a consideration of how workers in this field have tried to correlate the notion of the idea of supramolecular systems linking self-assembly considerations. Thereby, this is clearly an ad-vantage that optimized geometries obtained on the conductive bases described that undoubtedly, some of these systems have substantial applications and create a significant practical interest. The outline of this review encompasses a general introduction to MOFs and supramolecularity, the key unit of the study presented here, followed by a survey of recent advances in supramolecular chemistry in confined space, relationships of MOFs with the supramolecular chemistry, electro-chemical synthesis of MOFs, and switchable MOFs. Finally, some discussion on possible future perspectives of this field is given.

Climate change is one of the main issues that humanity is currently facing due to carbon dioxide emissions caused by the use of fossil fuels. Organic Rankine cycles may play an important role in reducing these emissions since they can be operated by using industrial waste heat of renewable energies. The present study presents a comprehensive bibliographic review of organic Rankine cycles. The study not only actualizes previous reviews that mainly focused on basic cycles operating on subcritical or supercritical conditions but also includes the analysis of novel cycles such as two-stage and hybrid cycles and the used fluids. Recuperative and regenerative cycles are more efficient than reheated and basic single-stage cycles. The use of two-stage cycles makes it possible to achieve higher thermal efficiencies and net power outputs of up to 20% and 44%, respectively, compared with those obtained with single-stage cycles. Theoretical studies show that hybrid systems, including Brayton and organic Rankine cycles, are the most efficient; however, they require very high temperatures to operate. Most organic Rankine cycle plants produce net power outputs from 1 kW up to several tens of kW, mainly using microturbines and plate heat exchangers.

Although increasing knowledge about biological systems has advanced exponentially in recent decades, it is surprising to realize that the very definition of Life keeps presenting theoretical challenges. Even if several lines of reasoning seek to identify the essence of life phenomenon, most of these thoughts contain fundamental problem in their basic conceptual structure. Most concepts fail to identify necessary and sufficient features to define life. Here, we analyzed the main conceptual framework regarding theoretical aspects supporting life concepts, such as (i) the physical, (ii) the cellular and (iii) the molecular approaches. Based on ontological analysis, we propose that Life should not be positioned under the ontological category of Matter. Yet, life should be better understood under the top-level ontology of “Process”. Exercising an epistemological approach, we propose that the essential characteristic pervading each and every living being is the presence of organic codes. Therefore, we explore theories in biosemiotics in order to propose a clear concept of life as a macrocode composed by multiple inter-related coding layers. Therefore, we suggest a clear distinction between the concept of life and living beings, a distinction that is not evident in theoretical terms. From the proposed concept, we suggest that the evolutionary process is a fundamental characteristic for life’s maintenance but not to its definition. The current proposition opens a fertile field of debate in astrobiology, biosemiotics and robotics.

The evolution of photovoltaic cells is intrinsically linked to advancements in the materials from which they are fabricated. This review paper provides an in-depth analysis of the latest developments in silicon-based, organic, and perovskite solar cells, which are at the forefront of photovoltaic research. We scrutinize the unique characteristics, advantages, and limitations of each material class, emphasizing their contributions to efficiency, stability, and commercial viability. Silicon-based cells are explored for their enduring relevance and recent innovations in crystalline structures. Organic photovoltaic cells are examined for their flexibility and potential for low-cost production, while perovskites are highlighted for their remarkable efficiency gains and ease of fabrication. The paper also addresses the challenges of material stability, scalability, and environmental impact, offering a balanced perspective on the current state and future potential of these material technologies.