In the process of oil and gas development and production, when the flow rate in the wellbore is large, the materials underground will be eroded, causing the operation to be unable to proceed smoothly and reducing the efficiency of oil and gas production. Therefore, optimizing the anti-erosion coating under high-speed flow conditions in wellbore is a very interesting thing. It can greatly improve operational efficiency. In this paper, laser cladding was used to prepare the new coating used in the PDC drill bit. Then, the effects of tungsten carbide and multi-layer graphene on the microstructure and properties of the tungsten carbide coating were studied. The research results indicate that, for new coatings, 60% tungsten carbide and 0.3% graphene are the optimal ratios. After adding WC, the hardness has significantly improved. However, when the WC content further increases more than 30%, the increase in hardness is relatively small. In addition, when the content of graphene is more than 0.3%, the branched structure became thicker, and not only the segregation of Cr, Si and W became very obvious again, but also the segregation of Fe occurred at the Ni enrichment site. The research results contribute to improving oil and gas production and operational efficiency under high-speed fluid flow conditions in the wellbore.

Visible-light photocatalysis, particularly in its application to organic synthesis, has experienced a big renaissance in the past decade. The rational design of new photocatalysts with designed and improved photocatalytic properties, that at the same time circumvents the necessity of using scarce and toxic transition metals, will predictably play a key role in photocatalysis in the next few years. Although free-base porphyrins were identified some years ago as a promising, easily accessible and easily tunable class of organic photoredox catalysts, a systematic study on the effect of the electronic nature and of the position of the substituents on both the ground-state and the excited-state redox potentials of these compounds is still lacking. We have prepared a set of known functionalized derivatives of meso-tetraphenyl porphyrin containing different substituents either in one of the meso-positions or at a beta-pyrrole carbon and we have determined their ground- and (singlet) excited-state redox potentials. This survey has led us to conclude that the introduction of a carbonyl group at the beta-pyrrolic position strongly increases the facility of the monoelectronic reduction of the porphyrin both in the ground state and in the singlet excited state. We have also prepared a second set of four previously unknown benzoyl derivatives of meso-tetraphenylporphyrin, and we have confirmed the validity of our conclusions.

This study aimed to analyse the variation of recreational water quality in Plettenberg Bay in an attempt to comprehend the effects of pollution on the environment, and more specifically the potential impacts on the quality of surface water used for recreational activities. Plettenberg Bay is a major destination for tourists in South Africa, with recreational water activities representing an important attraction. For this study, data were obtained from Bitou Municipality, the local au-thority in charge of the water monitoring program in Plettenberg Bay. The selected datasets contained water quality data collected by the Bitou Municipality waterworks department in three sampling sites in Plettenberg Bay. The samples were tested for six water quality parameters namely, Ammonia, Suspended Solids, Conductivity, Nitrates/Nitrites, pH, and E coli. Water quality trends appeared stabile over the five years, with only a few parameters showing variation in their concentration levels. It is recommended that the Bitou Municipality increase the sampling frequency to allow a clearer understanding of water quality variation and to minimise potential uncertainties.

In the face of escalating cybercriminal sophistication, an innovative approach to network anomaly detection has been pursued in this longitudinal study, integrating computational data analytics in a geographic, organizational, and behavioral context. A data-driven scoring mechanism was employed to systematically analyze and correlate source countries of IP addresses and organization-associated Autonomous System (AS) Numbers (ASN) with network anomalies. Significant correlations between certain countries, specific organizations, and high behavior scores were identified through the data analytics. An increase in connection requests was also found to be linked with elevated behavior scores. Validated by cross-validation techniques, these findings emphasize the necessity for continuous model recalibration. The transformative role of integrative data analytics in cybersecurity is underscored, paving the way for the development of more sophisticated, context-aware anomaly detection systems. Specifically, the analysis underscores the need for organizations to adopt a proactive and adaptive approach to cybersecurity that can keep pace with the evolving threat landscape.

This research article investigates the effectiveness of digital forensics analysis (DFA) techniques in identifying patterns and trends in malicious failed login attempts linked to public data breaches or compromised email addresses in Microsoft 365 (M365) environments. Pattern recognition techniques are employed to analyze security logs, revealing insights into negative behavior patterns. The findings contribute to the literature on digital forensics, opposing behavior patterns, and cloud-based cybersecurity. Practical implications include the development of targeted defense strategies and the prioritization of prevalent threats. Future research should expand the scope to other cloud services and platforms, capture evolving trends through more prolonged, more extended analysis periods, and assess the effectiveness of specific mitigation strategies for identified tactics, techniques, and procedures (TTPs).

The study of biologically active substances from natural sources shows the prospect of obtaining a new type of antimicrobial agents, highly effective against pathogenic microorganisms and non-toxic to humans. Our study reveals for the first time that Cornu aspersum mucus has the potential to act as a source of antibacterial agents against bacterial pathogens such as Bacillus cereus 1085, Propionibacterium acnes 1897, Salmonella enterica 8691, Enterococcus faecalis 3915, and Enterococcus faecium 8754. Both mucus fractions with MW<20 kDa and MW>20 kDa showed antimicrobial activity and antioxidant properties that’s why they can be turned into an alternative agent to expensive synthetic antibacterial compounds. Using de novo sequencing 16 novel peptides with potential antibacterial activity were identified by in a fraction with MW<20 kDa. The results of electrophoretic and proteomic analysis of mucus fraction with MW >20 kDa presented proteins with potential antibacterial activity highly homologous to hemocyanins, mucus protein Aspernin, lectins, L-amino acid oxidase-like protein, and mucins (mucin-5AC, mucin-5B, mucin-2 and mucin-17). Thanks to the synergistic action of the bioactive components, the mucus fraction with MW > 20 kDa in low concentrations per 8–2 µg/mL showed promising antimicrobial activity against the tested bacteria, comparable to Vancomycin and without unwanted cytotoxic effects against non-target cells. Additionally, C. aspersum mucus fractions were found to have a positive effect on eukaryotic organisms by reducing the levels of intracellular oxidative damage and increasing the antioxidant capacity of the cell. These findings could serve as a basis for the development of a potent non-cytotoxic antibacterial agent to replace conventional antibiotics and avoid the development of antibiotic resistance.

A groundbreaking integrated predictive model, termed Cyber Forensics Behavioral Analysis (CFBA), has been developed in an environment characterized by rapidly evolving and increasingly sophisticated cyber threats. This model merges Cyber Behavioral Sciences with Digital Forensics to enhance the prediction accuracy and effectiveness of cyber threats originating from specific Autonomous System Numbers (ASNs). It has been observed that traditional cybersecurity strategies, predominantly focused on technical aspects, must be improved in addressing the complex landscape of cyber threats. Consequently, a novel approach has been proposed in this research, combining technical expertise with insights into the behavior of cybercriminals, thereby addressing a significant gap in existing methodologies. A mixed-methods approach has been employed in the study, integrating quantitative and qualitative research methods. This approach has created a comprehensive framework incorporating digital forensics, cybersecurity, computer science, forensic psychology, and the cyber behavioral sciences which incorporates disciplines scuch as cyberpsychology and forensic cyberpsychology. The study is anchored around four key concepts: (1) Forensic Cyberpsychology, which focuses on understanding psychological aspects of cybercriminal behavior; (2) Digital Forensics, involving the collection and analysis of digital evidence from cyber incidents; (3) Predictive Modeling, which utilizes historical data and patterns to anticipate potential cyber threats; and (4) the Cyber Behavioral Analysis Metric (CBAM) and Cyber Behavioral Score (CBS), tools designed for evaluating and scoring ASNs based on their behavior in terms of cybersecurity threat risks. Challenges encountered in the development of this integration have been significant. Initial setbacks included the misalignment of traditional cyber defense methods with the evolving nature of cyber threats and the absence of a holistic approach in pre-existing models. Through the narrative of these challenges and the subsequent development of the CFBA model, the research highlights the necessity for an interdisciplinary approach to cybersecurity. The outcomes of this study are not merely theoretical but provide practical, actionable tools and frameworks that markedly improve the precision of predicting cyber threats, especially from ASNs. The CFBA model represents a significant shift in cybersecurity strategies, highlighting the importance of integrating behavioral insights with technical knowledge. The study emphasizes the need for ongoing research and collaboration in cybersecurity, advocating for an approach that is as comprehensive and multifaceted as the cyber threats it seeks to mitigate. This research has been conducted to contribute significantly to cybersecurity, offering new perspectives and methodologies in a rapidly changing domain.

The grain-to-grain stress vertically in sediments is given by the overburden less the pore fluid pressure, σ, divided by the fraction of the horizontal area which is the supporting matrix , (1 − φ), where φ is the porosity. It is proposed that the fractional reduction of this ratio, Λ, with time is given by the product of φ 4m/3 , (1 − φ) 4n/3 , and one or more Arrhenius functions A exp(−E/RT ) with m and n close to 1. This proposal is tested for shale sections in six wells from around the world for which porosity-depth data are available. Good agreement is obtained above 30-40 C and porosities less than 0.5. Single activation energies for each well are obtained in the range 15-33 kJ/mole, close to pressure solution of quartz, 24 kJ/mol. Values of m and n are in the range 1 to 0.8, indicating nearly fractal pore-matrix spaces and water-wet interfaces. Results are independent of over- or under-pressure of pore water. This model explains shale compaction quantitatively. Given porosity-depth data and accurate activation energy, E, one can infer paleo-geothermal-gradient and from that organic maturity, thus avoiding unnecessary drilling.

The present article describes the synthesis of an isonicotinate-derived meso-arylporphyrin, that has been fully characterized by spectroscopic methods (including fluorescence spectroscopy), as well as by elemental analysis and by HR-MS. The structure of a n-hexane monosolvate has been determined by single crystal X-ray diffraction analysis. The radical scavenging activity of this new porphyrin against the 2,2-diphenyl-1-picrylhydrazyl (DDPH) radical has been measured. Its antifungal activity against three yeast strains (C. albicans ATCC 90028, C. glabrata ATCC 64677 and C. tropicalis ATCC 64677) has been tested, using the disk diffusion and the microdilution methods. Whereas the measured antioxidant activity was low, the porphyrin showed moderate but encouraging antifungal activity. Finally, a study of its effect on the germination of lentil seeds revealed interesting allelopathic properties.

The chemical investigation of the anti-yeast methanol extract from the stem bark of Terminalia mantaly led to the isolation of seven compounds: 3-O-methyl-4-O-α-rhamnopyranoside ellagic acid (1), 3-O-mehylellagic acid (2), arjungenin or 2,3,19,23-tetrahydroxyolean-12-en-28-oïc acid (3), arjunglucoside or 2,3,19,23-tetrahydroxyolean-12-en-28-oïc acid glucopyranoside (4), 2α,3α,24-trihydroxyolean-11,13(18)-dien-28-oïc acid (5), stigmasterol (6), stigmasterol 3-O-β-D-glucopyranoside (7). Their structures were established by means of spectroscopic analysis and comparison with published data. Compounds 1-5 were tested in vitro for activity against three pathogenic yeast isolates, Candida albicans, Candida parapsilosis and Candida krusei. The activity of compounds 1, 2 and 4 were comparable to that of the reference compound fluconazole (MIC values below 32 µg/ml) against the three tested yeast isolates. They were also tested for inhibitory properties against four enzymes of metabolic significance: Glucose-6-Phosphate Deshydrogenase (G6PD), human erythrocyte Carbonic anhydrase I and II (hCA I and hCA II), Glutathione S-transferase (GST). Compound 4 showed highly potent inhibitory property against the four tested enzymes with overall IC₅₀ values below 4 µM and inhibitory constant (Ki) <3 µM.

Weathering and erosion transport minerals and organics toward the sea or lake bottoms over geologic time. The finest solids are deposited in lower, less turbulent areas, such as lake bottoms and continental shelves. They sometimes stack up to thicknesses of kilometers, and begin compacting. These sediment sections are called shales, and as initially deposited in water, shales can have porosities up to 50-80{\%} water, As they are buried, many alteration products from oil to slate are produced due to overburden and temperature increasess, making them important to study. A preceeding paper \cite{1} showed that pressure solution is the primary mechanism for porosity reduction, with possible mechanical compaction at shallow depths. Without naming the mineral(s) involved, it postulated that the greater the product of the water and pore interfaces, the faster the reaction would proceed. This term is $ \varphi^{4m/3}(1-\varphi)^{4n/3}$ , where $\varphi$ is porosity and m and n are numbers close to unity. The large exponents, {\em 4/3}, recognize that the reaction occurs at the molecular scale at which the surfaces are rough. A second term, $\exp^{(-E/RT)}$ , indicates that the reaction is impeded by a quantum energy barrier, E, with diminished impeding power as increased available thermal energy, represented by the absolute temperature, T, becomes available at greater depths in the Earth. These two factors combine to allow porosity $\varphi$ to reduce with time, or equivalently for the fraction of solids, $(1-\varphi)$, to increase with time,$\left. \frac{\partial(ln(1-\varphi) ) }{\partial t } \right |_{\sigma} = (\varphi )^{4m/3}( 1-\varphi )^{4n/3}Ae^{-E/(RT)}$. { \em Here it is shown that this equation can cover quantitatively any actual deposition rates which may have been experienced by the six sections studied, the actual deposition rates being unknown for these cases. Hence a time-depth depositional history for any new shale section, known in detail, would allow determination of the parameters m, n, E and a lumped proportionality constant A. This was accomplished by showing that, for a wide range of depositional rates, r, the range of E for any of the studied sections is small compared to laboratory measurements of quartz solution\cite{2}, 24+-15kJ/mol. Results were obtained over this range of r's using the previously determined m and n, and porosity and temperature profiles. The presently existing porosity profiles necessarily incorporate any overpressure or underpressure conditions that may have existed in the past or currently, as the net difference between overburden and pore pressure is a primary driving force for pressure solution. $SiO_2$ usually comprises 20-50{\%} of shales. In conclusion, pressure solution of quartz can account for vertical compaction of shales quantitatively in the studied examples. Separately, a quasi-eqivalent method for discussing reduced porosities in Macron 2 versus Macron 1 as increased vertical stress, rather than additional horizontal stress, is illustrated. Experiments are suggested to clarify the pressure solution mechanism. The role of horizontal forces is discussed. From a global point of view, shale compaction by pressure solution is a quantified step in the cycling of continental rocks, beginning with rifting.

Alkaloid-based urea derivatives were produced with high yield through the reaction of anabasine and cytisine with isoxazolylphenylcarbamates in boiling benzene. Their antitumor ac-tivity in combination with the commonly used six anticancer drugs namely cyclophosphane, fluorouracil, etoposide, cysplatine, ribomustine with different mechanisms of action was investi-gated. Based on the quantum chemical calculations data and molecular docking, hypotheses have been put forward to explain their mutual influence when affecting on the С6 rat glioma model cells.

During the last years there has been a high interest in the development of new purely-organic single-component conductors. Very recently, we have reported a new neutral radical conductor based on the perchlorotriphenylmethyl (PTM) radical moiety linked to a monopyrrolo-tetrathiafulvalene (MPTTF) unit by a -conjugated bridge (1). Interestingly, this system behaves as a semiconductor with high conductivity and small energy gap under high pressure. With the aim of developing a new material with improved conducting properties, we have designed and synthesized the radical dyad 2 which was functionalized with an ethylenedithio (EDT) group in order to improve the intermolecular interactions of the TTF subunits. The physical properties of the new radical dyad 2 were studied in detail in solution to further analyze its electronic structure as well as its potential use as radical conductor in the solid state.

The effect of doublet state metalloradical complex in a solar cell inside the common active layer poly(3-hexylthiophene)/ [6,6]-phenyl-C61-butyric acid methyl ester (P3HT/PC60BM) is explored. In this work is demonstrated that the role of the Bis-[1,3-Bis-(2,6-diisopropylphenyl)-4,5-dichloroimidazol-2-ylidene]palladium(I) hexafluoridophosphate dopant, [Pd(IPrCl)2][PF6], is crucial because, by having a stable unpaired electron in the molecule, it significantly improves the optoelectronic performance of the devices. We found the optimal concentration of this molecule in the active layer, and we demonstrated that the presence of this additive in the active layer helps to significantly improve the morphology of the device. The improvements in optoelectronic and morphological parameters are associated with a remarkable increase of photocurrent generation due to more favourable mechanisms of charge separation at the donor/acceptor (D/A) interfaces of the active layer and reduced recombinations. Moreover, the presence of this additive improves the stability of the unencapsulated solar cell against photochemical degradation produced by sunlight.

Japanese plum tree (Prunus salicina Lindl.) is mainly cultivated in temperate areas of China and some European countries. Certain amounts of wood (from pruning works) are generated every year from this crop of worldwide commercial significance. The main objective of this work was to value this agricultural woody residue, for which the chemical composition of pruning wood extracts from six Japanese plum cultivars was investigated, and the antiproliferative activity of extracts and pure phenolics present in those extracts was measured. For the chemical characterization, total phenolic content and DPPH radical-scavenging assays and HPLC‒DAD/ESI‒MS analyses were performed, the procyanidin (‒)-ent-epicatechin-(2α→O→7,4α→8)-epicatechin (5) and the propelargonidin (+)-epiafzelechin-(2β→O→7,4β→8)-epicatechin (7) being the major components of the wood extracts. Some quantitative differences were found among plum cultivars, and the content of proanthocyanidins ranged from 1.50 (cv. ‘Fortune’) to 4.44 (cv. ‘Showtime’) mg/g of dry wood. Regarding the antitumoral activiy, eight wood extracts and four phenolic compounds were evaluated in MCF-7 cells after 48 h of induction, showing the wood extract from cv. ‘Songold’ and (‒)-annphenone (3) the best antiproliferative activity (IC50: 424 ppm and 405 ppm, respectively).

Leishmaniasis are neglected diseases that affect regions such as South Asia, South Africa and Latin America, less developed regions. Current treatment, for cutaneous, mucocutaneous and visceral leishmaniosis, which are the main forms of the disease, is based on the administration of pentavalent antimonial and amphotericin B. However, these drugs have low efficacy and high toxicity. For this reason, the search for new treatments for this disease is necessary, based on studies of new molecules and their conformations. The research proposed the conformational study of brominated guanidine compounds with potential antileishmanial activity using Nuclear Magnetic Resonance (NMR) and X-ray diffraction (XRD) techniques. The present study involves the bro-minated molecules, LQOF-G2, LQOF-G30, LQOF-G35 and LQOF-G35-Br. The later was synthesized by the reaction of LQOF-G35 with NBS under IR irradiation at 120 Watts of potency and dichloro-methane as solvent by 12-h of exposition. The obtained results demonstrated the efficiency of the bromination method, since two bromines atoms entered the molecule. Furthermore, NMR analysis showed the occurrence of a conformational change from Z to E when compound LQOF-G35 was brominated to LQOF-G35-Br. This feature was well confirmed by comparative DRX study of the LQOF-G35 and LQOF-G35-Br compounds. The antileishmanial activity of LQOF-G2 e LQOF-G35 motivated the synthesis of new brominated compounds LQOF-G30 e LQOF-G35-Br.

Studying various marine biomineralized ultrastructures reveals the appearance of common architectural designs and building blocks in materials with fascinating mechanical properties that match perfectly to their biological tasks. Advanced mechanical properties of biological materials are attributed to evolutionary optimized molecular architectures and structural hierarchy. One example which has not yet been structurally investigated in great detail is the shell of Mytilus edulis L. (Finnish blue mussel) found in the archipelago of SW-Finland. Through a combination of various state-of-the-art techniques such as high-resolution electron microscopy imaging, Fourier-transformed infrared spectroscopy, powder X-ray diffraction, synchrotron wide-angle X-ray diffraction, nanoindentation and protein analysis, both the inorganic mineralized components as well as the organic-rich matrix were extensively characterized. We found very similar ultra-architecture across the shell of M. edulis L. as compared to the widely studied and closely related M. edulis. However, we also found interesting differences, for instance in the thickness and degree of orientation of the mineralized layers indicating dissimilar properties and related alterations in the biomineralization processes. Our results show that the shell of M. edulis L. has a gradient of mechanical properties, with the increase in the stiffness and the hardness from anterior to the posterior region of the shell. The shell is made from distinct and recognizable mineralized layers each varying in thickness and microstructural features. At posterior regions of the shell, moving from dorsal to ventral side, these layers are an oblique prismatic layer, a prismatic layer and a nacreous layer, in which the oblique prismatic layer is found to be the main and thickest mineralized layer of the shell. Probing the calcified rods in the oblique prismatic layer using high resolution SEM imaging revealed opening of channels with a diameters of 40-50 nm and lengths up to a micrometer extending through the rods. The chitin and protein have been found to be the main component of the organic-rich interfacial matrix as expected. Protein analysis showed two abundant proteins with sizes around 100 kD and 45 kD which likely not only regulates biomineralization and adhesion of the crystals but also governing the intrinsic-extrinsic toughening in the shell. Overall, this detailed analysis provides new structural insights into biomineralization of marine shells in general.

We present a generic and open-source framework for the numerical modeling of the expected transport and storage mechanisms in unconventional gas reservoirs. These unconventional reservoirs typically contain natural fractures at multiple scales. Considering the importance of these fractures in shale gas production, we perform a rigorous study on the accuracy of different fracture models. The framework is validated against an industrial simulator and is used to perform a history-matching study on the Barnett shale. This work presents an open-source code that leverages cutting-edge numerical modeling capabilities like automatic differentiation, stochastic fracture modeling, multi-continuum modeling and other explicit and discrete fracture models. We modified the conventional mass balance equation to account for the physical mechanisms that are unique to organic-rich source rocks. Some of these include the use of an adsorption isotherm, a dynamic permeability-correction function, and an embedded discrete fracture model (EDFM) with fracture-well connectivity. We explore the accuracy of the EDFM for modeling hydraulically-fractured shale-gas wells, which could be connected to natural fractures of finite or infinite conductivity, and could deform during production. Simulation results indicates that although the EDFM provides a computationally efficient model for describing flow in natural and hydraulic fractures, it could be inaccurate under these three conditions: 1. when the fracture conductivity is very low. 2. when the fractures are not orthogonal to the underlying Cartesian grid blocks, and 3. when sharp pressure drops occur in large grid blocks with insufficient mesh refinement. Each of these results are very significant considering that most of the fluids in these ultra-low matrix permeability reservoirs get produced through the interconnected natural fractures, which are expected to have very low fracture conductivities. We also expect sharp pressure drops near the fractures in these shale gas reservoirs, and it is very unrealistic to expect the hydraulic fractures or complex fracture networks to be orthogonal to any structured grid. In conclusion, this paper presents an open-source numerical framework to facilitate the modeling of the expected physical mechanisms in shale-gas reservoirs. The code was validated against published results and a commercial simulator. We also performed a history-matching study on a naturally-fractured Barnett shale-gas well considering adsorption, gas slippage & diffusion and fracture closure as well as proppant embedment, using the framework presented. This work provides the first open-source code that can be used to facilitate the modeling and optimization of fractured shale-gas reservoirs. To provide the numerical flexibility to accurately model stochastic natural fractures that are connected to hydraulically-fractured wells, it is built atop other related open-source codes. We also present the first rigorous study on the accuracy of using EDFM to model both hydraulic fractures and natural fractures that may or may not be interconnected.

In the frame of our diversity-oriented research on multitarget small molecule anticancer agents, utilizing convergent synthetic sequences terminated by Sonogashira coupling reactions, a preliminary selection of representative alkyne-tethered vindoline hybrids was synthesized. The novel hybrids with additional pharmacophoric fragments of well-documented anticancer agents, including FDA-approved tyrosine-kinase inhibitors (imatinib and erlotinib) or ferrocene or chalcone units, were evaluated for their antiproliferative activity on malignant cell lines MDA-MB-231 (triple negative breast cancer), A2780 (ovarian cancer), HeLa (human cervical cancer) and SH-SY5Y (neuroblastoma) as well as human embryonal lung fibroblast MRC-5 served as reference non-malignant cell line for the assessment of the therapeutic window of the tested hybrids. The biological assays identified a trimethoxyphenyl-containing chalcone-vindoline hybrid (36) as a promising lead compound exhibiting submicromolar activity on A2780 cells with a marked therapeutic window. These results suggest that ovarian cancer might be considered as a prioritized target of treatment with 36.

For centuries, humans have relied on natural products to prevent and treat numerous health issues. However, biologically active compounds from natural sources, such as polyphenols, face significant challenges, including low solubility, rapid metabolism, and instability, which hinder their effectiveness. Advances in science and nanotechnology have provided solutions to overcoming these problems through the use of porous silica materials. These materials possess unique properties, such as a high specific surface area, adjustable particle and pore sizes, and a surface that can be easily and selectively modified. In this review, we summarize and discuss findings on how the pore and particle size, structure, and surface modification of silica materials influence the preparation of efficient delivery systems for biologically active polyphenols from natural sources. The available data demonstrate how parameters such as adsorption capacity, release and antioxidant properties, bioavailability, solubility, stability, etc. of the studied delivery systems could be affected by the structural and chemical characteristics of the porous silica carriers.

Indole is a versatile pharmacophore widely distributed in bioactive natural products. This privileged scaffold has been found in a variety of molecules isolated from marine organisms such as algae and sponges. Among these, indole alkaloids represent one of the biggest, most promising family of compounds, having shown a wide range of pharmacological properties, including anti-inflammatory, antiviral and anticancer activities. The aim of this review is to show the current scenario of marine indole alkaloid derivatives, covering not only the most common chemical structures, but also new synthetic routes developed during the last years as well as promising therapeutic applications.

Colombia is noteworthy as a biodiversity hotspot, featuring an extraordinary number of en-demic orchids, birds, and butterflies. This exploratory study examines the perceptions of desti-nation image considering the cognitive and affective image in predicting behavioral intentions of ecotourists through symmetric data analysis. Using Partial Least Squares (PLS), the author(s) analyzed 64 survey responses collected of rural areas, including a new 15 statement scale spe-cialized on birdwatching. The findings support the reliability of the model, symmetric analysis presents the higher influence of emotions and affections in increasing intentions of recommen-dation, considering birdwatching as based on personal relationships. Additionally, the cognitive image for the birders despite representing destination attributes or sets of destination resources of a mental picture does not have the same impact on behavioral intentions. Therefore, manag-ers should develop positioning strategies based on the generation of emotions, because bird-watching tourists seek to have more emotional experiences.

Hybrid reinforcement in a composite material (CM), in many situations, allows better govern material mechanical properties. Polymer matrix CM plate is reinforced with small particles and macro-fibers. Particles are oil shale ash (OSA) powder, macro-fibers – basalt fiber threads im-pregnated by matrix material. With the goal to find out elastic properties of the matrix- polymer with OSA, samples with its different concentrations were experimentally fabricated and their elastic properties were experimentally measured. Obtained data were used in numerical model-ling. Was observed polymer matrix composite slab, reinforced with OSA and three-dimensional (3D) basalt fiber fabric. Fabric are forming threads impregnated by matrix (polymer resin mixed with OSA particles). Damage accumulation in the stretched slab was modelled. Impregnated thread, in the modelling, is observed as a macro-fiber (MF) with averaged elastic properties. With the load increase MF in the material began to break. At first, appeared isolated single breaks. A probabilistic sequential MF rupture accumulation model was accepted and numerical-ly realized. The geometry of the reinforcing knitted fabric was modeled using the Leaf and Glaskin approach. In the knitted fabric highly, stressed MF cross-sections are observed as po-tential location where thread breakage can occur. If one thread breaks, the cross-sections of the adjacent threads experience the overload caused by this rupture. More overloaded crossection in the adjacent overloaded thread breaks and we obtain two adjacent broken MF designated as a defect with the size j=2. The probabilities of obtaining defect consisting of at least 2, 3, … j adjacent broken MF in the plate were calculated. The calculations continued until the rupture process becomes unstable (j→∞). The overstresses on adjacent threads in the CM were calculat-ed using the FEM three-dimensional numerical approach. Analytical and stochastic methods were used for the load-carrying capacity determination and different size defects accumulation in the hybrid composite material (HCM) plate. Also, was calculated the probability of the plate rupture.

In recent years there has been an increasing interest in developing novel materials based on natural biopolymers as a renewable alternative of petroleum-based plastics. The availability of proteins derived from agricultural by-products, along with their favourable properties, has fostered a renewed interest in protein-based materials, promoting research in innovative technologies. In this study we propose the use of rapeseed protein-rich meal as main ingredient for the preparation of novel sustainable materials combining excellent environmental properties such as biodegradability and renewable origin. Application as sustainable products in the present high-tech society needs modification of basic native properties of these natural compounds. The original route proposed in this paper consists in the preparation via compression moulding of flexible biomaterials stabilized by crosslinkers/chain extenders. Investigation of the effects of different denaturing and disulfide bond reducing agents, crosslinkers, and preparation conditions on the material mechanical behaviour demonstrated that the novel materials have appreciable strength and stiffness. The results show the potential of utilizing full meal from vegetable by-products to prepare protein-based materials with granted ecofriendly characteristics and mechanical properties adequate to specific structural applications.

Xanthone derivatives, a class of natural compounds abundantly found in plants such as mangosteen (Garcinia mangostana) and certain herbs, have garnered substantial interest due to their diverse pharmacological properties, including antioxidant, anti-inflammatory, and anti-cancer activities. Recent investigations have unveiled their potential as modulators of enzymatic activity, prompting exploration into their effects on hyaluronidase-mediated HA degradation, and their effects in topical treatment of telangiectasia and rosacea. Telangiectasia and rosacea are common dermatological conditions characterized by chronic skin inflammation, vascular abnormalities, and visible blood vessels, resulting in significant cosmetic concerns and impaired quality of life for affected individuals. This review aims to provide a comprehensive overview of the current understanding regarding the interplay between mechanisms of action by which xanthone derivatives exert their therapeutic effects, including the inhibition of pro-inflammatory cytokines, modulation of oxidative stress pathways, and regulation of vascular endothelial growth factors. Furthermore, we will discuss the implications of harnessing xanthone derivatives as therapeutic agents for mitigating vascular dysfunction and its associated pathologies, thereby offering insights into future research directions and therapeutic strategies in the field of vascular biology.

Hydrogen gas (H2) has attracted attention as a next-generation clean energy source. Its efficient and safe preparation and utilization are crucial in both industry and organic chemistry. In this study, a Pt/CB-catalyzed MW-mediated continuous-flow hydrogenation reaction was developed using methylcyclohexane (MCH) as the reducing agent (hydrogen carrier). Alkynes, alkenes, nitro groups, benzyl esters, and aromatic chlorides were chemoselectively hydrogenated using Pt/CB under MW-assisted continuous-flow conditions. This methodology represents a safe and energy-efficient hydrogenation process, as it eliminates the need for an external hydrogen gas supply or heating jackets as a heat medium. Further application of MW-mediated continuous-flow hydrogenation reactions is a viable method for the efficient generation and utilization of sustainable energy.

Over the past decades, research has escalated on the use of polylactic acid (PLA) as replacement for petroleum-based polymers. This is due to its valuable properties, such as renewability, biodegradability, biocompatibility and good thermomechanical properties. Despite possessing good mechanical properties comparable to conventional petroleum-based polymers, PLA suffers from some shortcomings such as low thermal resistance, heat distortion temperature and rate of crystallization, thus different fillers have been used to overcome these limitations. In the frame work of environmentally friendly processes and products, there has been growing interest on the use of cellulose nanomaterials viz. cellulose nanocrystals (CNC) and nanofibers (CNF) as natural fillers for PLA towards advanced applications other than short-term packaging and biomedical. Cellulosic nanomaterials are renewable in nature, biodegradable, eco-friendless and they possess high strength and stiffness. In the case of eco-friendly processes, various conventional processing techniques, such as melt extrusion, melt-spinning, and compression moulding, have been used to produce PLA composites. This review addresses the critical factors in the manufacturing of PLA-cellulosic nanomaterials by using conventional techniques and recent advances needed to promote and improve the dispersion of the cellulosic nanomaterials. Different aspects, including morphology, mechanical behavior and thermal properties, as well as comparisons of CNC- and CNF reinforced PLA, are also discussed

The critical role of global electron density transfer (GEDT) in increasing the reaction rate of polar organic reactions has been studied within the framework of Molecular Electron Density Theory (MEDT). To this end, the series of the polar Diels-Alder (P-DA) reactions of cyclopentadiene with cyanoethylene derivatives, for which experimental kinetic data are available, have been chosen. A complete linear correlation between the computed activation Gibbs free energies and the GEDT taking place at the polar transition state structures (TSs) is found; the higher the GEDT at the TS, the lower the activation Gibbs free energy. An interacting quantum atoms (IQA) energy partitioning analysis allows establishing a complete linear correlation between the electronic stabilization of the electrophilic ethylene frameworks and the GEDT taking place at the polar TSs. This finding supports Parr’s proposal for the definition of the electrophilicity  index (J. Am. Chem. Soc., 1999, 121, 1922). The present MEDT study allows establishing the critical role of the GEDT in the acceleration of polar reactions, since the electronic stabilization of the electrophilic framework with the electron density gain is greater than the destabilization of the nucleophilic one, making a net favorable electronic contribution to the decrease of the activation energy.

The growing interest in benchtop NMR systems is visible in a vast number of applications in science and industry. Low-field nuclear magnetic resonance (LF-NMR) became an instant in technologies that productions are dependent on the reliable structure identification, grade and purity control, chemical process inspection or reaction monitoring. Beyond the benefits of being cost-, space-, maintenance- and user friendly, insufficient sensitivity and low signal resolution are the main drawbacks, due to which the low-field NMR (LF-NMR) in the fields of organic chemistry and synthesis remains limited to solely academic teaching purposes. Herein, we discuss the possibilities of LF-NMR for the needs of organic chemistry and synthesis on a set of compounds 1-4 achieved as the products of student’s laboratory course and organic derivatives 5-8 that are from our research interests. Chemical structure determination of all compounds 1-8 presented herein was performed using the benchtop-type NMR instrument operating at 60 MHz (Pulsar Oxford Ltd.). Structure of novel compounds 5-7 prepared under the aims of our research was characterized by combined 1H/19LF-NMR and compared with an appropriate high-field NMR data from Bruker Ascend Instrument (400 MHz). Finally, possibilities of the low-field NMR as an analytical tool for the research purposes in the fields of organic chemistry and synthesis are documented on a set of 1H and 2D 1H-1H COSY for azomethine 8.

New furan, thiophene and triazole oximes were synthesized through several-step reaction paths to investigate their potential for development of central nervous systems (CNS)-active and cholinesterase-targeted therapeutics in organophosphorus compound (OP) poisonings. Acute OP poisoning is still a challenge in treating patients despite the development of a large number of oxime compounds that should have the capacity to reactivate acetylcholinesterase (AChE) and butyrylcholinesterase (BChE). The activity of these two enzymes, crucial for neurotransmission, are blocked by the OP, which has the consequence of disturbing normal cholinergic nerve signal transduction in the peripheral and CNS, leading to cholinergic crisis. Oximes in use have one or two pyridinium rings and cross the brain–blood barrier poorly due to the quaternary nitrogen. Following our recent study on 2-thienostilbene oximes, in this paper we described the synthesis of 63 heterostilbene derivatives out of which 26 oximes were tested as inhibitors and reactivators of AChE and BChE inhibited by OP nerve agents – sarin and cyclosarin. While the majority of oximes were potent inhibitors of both enzymes in micromolar range, we identified several oximes as BChE or AChE selective inhibitors with a potential for drug development. Moreover, even oximes were poor reactivators of AChE, four heterocyclic derivatives reactivated the cyclosarin-inhibited BChE up to 70%, and cis,trans-5 [2-((Z)-2-(5-((E)-(hydroxyimino)methyl)thiophen-2-yl)vinyl)benzonitrile] had comparable reactivation efficacy to the standard oxime HI-6. In silico analysis and molecular docking studies connected the kinetic data to the structural features of these oximes, and confirmed their productive interactions with the active site of the cyclosarin-inhibited BChE. Based on inhibition and reactivation and their ADMET properties regarding lipophilicity, CNS activity, and hepatotoxicity, these compounds could be considered for further development of CNS-active reactivators in OP poisoning as well as cholinesterase-targeted therapeutics in neurodegenerative diseases like Alzheimer’s and Parkinson’s.

Competency frameworks are developed for a variety of purposes, including describing professional practice and informing education and assessment frameworks. Despite the volume of competency frameworks developed in the healthcare professions, guidance remains unclear and is inconsistently adhered to (perhaps in part due to a lack of organising frameworks), there is variability in methodological choices, inconsistently reported outputs, and a lack of evaluation of frameworks. As such, we proposed the need for improved guidance. In this paper we outline a six-step model for developing competency framework that is designed to address some of these shortcomings. The six-steps comprise [1] identifying purpose, intended uses, scope, and stakeholders; [2] theoretically informed ways of identifying the contexts of complex, ‘real-world’ professional practice, which includes [3] aligned methods and means by which practice can be explored; [4] the identification and specification of competencies required for professional practice, [5] how to report the process and outputs of identifying such competencies, and [6] built-in strategies to continuously evaluate, update and maintain competency framework development processes and outputs. The model synthesizes and organizes existing guidance and literature, and furthers this existing guidance by highlighting the need for a theoretically-informed approach to describing and exploring practice that is appropriate, as well as offering guidance for developers on reporting the development process and outputs, and planning for the ongoing maintenance of frameworks.

Emerging autologous cellular therapies that utilize platelet-rich plasma (PRP) applications have the potential to play adjunctive roles in a variety of regenerative medicine treatment plans. There is a global unmet need for tissue repair strategies to treat musculoskeletal (MSK) and spinal disorders, osteoarthritis (OA), and patients with chronic complex and recalcitrant wounds. PRP therapy is based on the fact that platelet growth factors (PGFs) support the three phases of wound healing and repair cascade (inflammation, proliferation, remodeling). Many different PRP formulations have been evaluated, originating from human, in vitro, and animal studies. However, recommendations from in vitro and animal research often lead to different clinical outcomes because it is difficult to translate non-clinical study outcomes and methodology recommendations to human clinical treatment protocols. In recent years, progress has been made in understanding PRP technology and the concepts for bioformulation, and new research directives and new indications have been suggested. In this review, we will discuss recent developments regarding PRP preparation and composition regarding platelet dosing, leukocyte activities concerning innate and adaptive immunomodulation, serotonin (5-HT) effects and pain killing. Furthermore, we discuss PRP mechanisms related to inflammation and angiogenesis in tissue repair and regenerative processes. Lastly, we will review the effect of certain drugs on PRP activity, and the combination of PRP and rehabilitation protocols.

Diarrhea remains one of the leading causes of mortality worldwide, especially among children. Recent epidemiological studies conducted in developing countries identified Shigella species as the most predominant pathogenic bacteria responsible for diarrhea. Antimicrobial therapy is necessary for Shigella infections; however, the rapid emergence of resistance against existing antimicrobials in Shigella spp. poses a serious global health problem. To identify alternative antimicrobial compounds with activity against Shigella species, the pathogens responsible for bacterial diarrhea. In this study, we have applied antibacterial phenotypic screening to identify potent anti-Shigella compounds across a broad chemical diversity, including selected acetaminophen derivatives containing benzothiazoles backbone, and their combination with certain antibiotics. In continuation to our effort in searching potent antimicrobial compounds, we have found this time around that two acetaminophen derivatives containing benzothiazoles backbone (4a and 4b) could inhibit the growth of Shigella flexneri with common MIC value of 12.5 µg/ml. These compounds were established through a time-kill kinetics’ study to be bactericidal. Meanwhile, the 2-aminobenzothiazoles (1a and 1b) used for the synthesis of compounds 4 (a & b) were found to be poorly active (MIC: 100 µg/ml) against this pathogen. Combination studies of 4a and 4b with the least susceptible antibiotics (ceftriaxone and cotrimoxazole) demonstrated synergistic anti-Shigella activity. The present study demonstrates that the azobenzothiazole dyes 4 (a & b) can be repurposed as potential anti-Shigella compounds, which can serve as scaffolds for the development of new agents against infectious diarrhea caused by Shigella and other enteric pathogens, especially in developing countries.

New dimers of selected dipyridothiazines with an m-xylene linker have been designed, synthesized and characterized. Their structure was identified using 1H and 13C NMR as well as 2D NMR techniques (COSY, ROESY, HSQC and HMBC experiments) and HR MS spectrometry. The compounds were subjected to preliminary in silico biological profile tests using the Way2Drug server and analysis of the probable cytotoxic effect on various cancer cell lines. Preliminary in vitro cytotoxicity tests were performed against normal cell lines (HaCaT) and five cancer cell lines (SW480, SW620, MDA-MB-231, A-549, LN-229) showing moderate activity. An analysis of the structure-activity relationship was performed.

The reaction of berberine derivatives containing at O-9 position N,N-disubstituted acetamide fragments with sodium borohydride in methanol at 0 °C leads to a mild reduction of the "C" cycle with the formation of corresponding tetrahydroberberine derivatives with moderate to good yields.

Large-scale volumetric fracturing is generally used during shale gas development. The return rate of fracturing fluid is low, and a large amount of slickwater will be retained in the reservoir. The adsorption and desorption of partially hydrolyzed polyacrylamide (HPAM), an additive commonly used in slickwater, on the surface of shale was studied using Longmaxi Shale from the Sichuan Basin. The experimental results showed that the mass ratio of the HPAM solution to shale reached saturation adsorption at 20:1 when the concentration of HPAM solution was 1000 mg/L and 25:1 when the concentration of HPAM solution was 500 mg/L. The mass ratio of the HPAM solution to shale was fixed at 25:1, and the adsorption equilibrium was reached at a HPAM concentration of 1000 mg/L when the aqueous solution temperature was 30°C and 800 mg/L when the aqueous solution temperature was 60°C. The Langmuir adsorption model yielded a better fit than the Freundlich adsorption model. The adsorption equilibrium time at 30°C was at 60 min for a HPAM concentration of 500 mg/L, while for a concentration of 1000 mg/L, it was at 90 min. The adsorption equilibrium time at 60°C was 40 min for a HPAM concentration of 500 mg/L, whereas it was 60 min for a HPAM concentration at 1000 mg/L. The pseudo-second order kinetics model yielded better fits than the pseudo-first order kinetics model. The adsorption of HPAM on shale was strong, and the adsorbed HPAM resembled cobwebs adhering to the shale surface. HPAM on the surface of shale after adsorption could resist the desorption capacity of water. However, when the amount of adsorbed HPAM on shale increased significantly, the amount of residual HPAM on the surface of the shale decreased rapidly during desorption in deionized water. The desorption of HPAM on the shale surface followed a modified desorption model. The higher the concentration of HPAM adsorbed on the shale surface was, the easier it was to desorb, the easier it was to be removed from the shale.

In this research the efficiency of degradation of different organic contaminant classes, including pesticides (tembotrione, clomazone), pharmaceuticals (ciprofloxacin, 17α-ethinyl estradiol) and mycotoxins (zearalenone, deoxynivalenol, fumonisin B1), by subcritical water treatment, was studied in model systems. All experiments were conducted in a house-made batch type pilot reactor. The research was focused on the optimization of the treatment parameters by using moderate treatment conditions. Optimization of the remediation processes of water contaminated with 17α-ethinyl estradiol, tembotrione, clomazone, ciprofloxacin, was conducted by testing different homogeneous and heterogeneous catalysts, as well as different gas atmospheres (nitrogen and carbon-dioxide) for pressurization of the process system. Mycotoxins in water were degraded without catalysts and all experiments were conducted in nitrogen atmosphere. Optimization was conducted by defining the optimal combination of the treatment temperature and time, oriented towards energy saving and minimization of the technical requirements. The degradation efficiency in all tested samples was determined by HPLC analysis.

Organic electrophoretic coatings have gained significant attention due to their ability to provide a uniform and controlled coating thickness, high coating adhesion, and excellent corrosion protection properties. In this work, to investigate the aging behaviors of an organic electrophoretic coating for magnesium alloys, water absorption kinetics curves of the coatings after immersion in 3.5 wt.% NaCl at 20℃ and 40℃ were measured, and parameters such as the saturated water absorption and saturation time of the free film coatings were fitted to determine the densification evolution of the organic coatings. A tensile test was used to test the tensile strength of the organic coating during service to determine the evolution of the strength and toughness of the organic coating. The evolution of wet adhesion of organic coatings with service time was tested by ASTM D4541-02. The impedance spectra of the organic coatings under the above conditions were detected by EIS, and finally, the failure behavior of the organic coatings under immersion was analyzed.

Soot combustion experiments with 5%O2/He were conducted using model soot, and four distinct compositions of CexPr1-xO2-δ oxides were prepared, varying nominal cerium com-positions (x=0, 0.2, 0.3, and 1). The catalyst samples were comprehensively characterized using techniques such as XRD, Raman spectroscopy, HR-TEM, N2 adsorption at −196 °C, XPS, O2-TPD, H2-TPR, and work function measurements. The Pr-rich compositions, rang-ing from Ce0.3Pr0.7O2-δ to PrO2-δ, resulted in a significant increase in the total evolved O2 amounts and enhanced catalyst reducibility. However, a decrease in textural properties of the catalysts was noted, being particularly important for the pure praseodymia under the synthesis route conducted. The catalytic activity was investigated under two contact modes of mixing between soot and catalyst: loose and tight. The results revealed that the catalytic performance is associated with the surface contact in tight contact mode and with the combination of surface/subsurface/bulk oxygen mobility and the BET surface ar-ea in loose contact mode. Notably, the T10 and T50 parameters were achieved at much lower temperatures than the uncatalyzed soot combustion, even under loose contact conditions. Specifically, the 50% conversion was achieved at 511℃ and 538℃ for Ce0.3Pr0.7O2 and Ce0.2Pr0.8O2, respectively. While no direct correlation between catalytic activity and work function was observed a significant relationship emerges between work function values and the formation of oxy-gen vacancies, whatever the conditions used for these measurements. On the other hand, the ability to generate a high population of oxygen vacancies at low temperatures, rather than the direct activation of gas-phase O2, influences the catalytic performance of Pr-doped ceria catalysts, highlighting the importance of surface/subsurface oxygen vacancy generation, which was the parameter which showed better correlation with the catalytic activity, whatever the soot conversion value or the mode of contact considered.

The targeted compounds in this research, resveratrol analogs 1–14 were synthesized as mixtures of isomers by the Wittig reaction using heterocyclic triphenylphosphonium salts and various benzaldehydes. The planned compounds were those possessing the trans-configuration as the biologically active trans-resveratrol. The pure isomers were obtained by repeated column chromatography in various isolated yields depending on the heteroaromatic ring. It was found that butyrylcholinesterase (BChE) was more sensitive to the heteroaromatic resveratrol analogs than acetylcholinesterase (AChE), except for 6, the methylated thiophene derivative with chlorine, which showed equal inhibition toward both enzymes. Compounds 5 and 8 achieved the highest BChE inhibition with IC50 values of 22.9 and 24.8 μM, respectively. The same as with AChE and BChE, methylated thiophene subunits of resveratrol analogs showed better enzyme inhibition than unmethylated ones. Two antioxidant spectrophotometric methods, DPPH and CUPRAC, were applied to determine the antioxidant potential of new heteroaromatic resveratrol analogs. Molecular docking of these compounds was conducted to visualize the ligand-active site complexes' structure and identify the non-covalent interactions responsible for the complex's stability, which influence the inhibitory potential. As ADME properties are crucial in developing drug product formulations, they have also been addressed in this work. The potential genotoxicity is evaluated by in silico studies for all compounds synthesized.

Multi-stage hydraulic fracturing with horizontal well technology has been widely used in shale oil reservoir. After hydraulic fracturing, hydraulic fractures and opened beddings are intertwined, which result in a complex fracture network. As well as the migration of multi-phase fluids during fracturing and soaking processes, which lead to complex flowback performance, and brings dif-ficulty to productivity evaluation and flowback strategies optimization. In this paper, taking the Daqing Gulong shale reservoir as an example, a numerical model for flowback period, which considered oil-water-gas three-phase flow and orthogonal fracture network has been established. The characteristics and influencing factors of flowback performance have been deeply studied, and the flowback modes of shale oil are reasonably optimized. Factors such as PTPG (pseu-do-threshold pressure gradient), opened bedding stress sensitivity, opened bedding permeability and matrix permeability have obvious effects on the flowback performance, resulting in signifi-cant variations in production peaks, high yield periods, and decline rates. In addition, three flowback modes are distinguished based on the rate at which the BHP (bottom hole pressure) drops. These correspond to three types of choke modes. Based on the result of numerical model, three flowback modes are optimized and the impacts of different flowback modes on shale oil flowback are clarified. This study is particularly important for understanding the performance of shale oil flowback and guiding the efficient exploitation of shale oil.

The pore-throat radius of shale oil reservoir is extremely small, and it is difficult to accurately obtain the absolute permeability and oil-water two-phase relative permeability of actual oil reservoir through conventional core experiments. However, these parameters are very important for reservoir numerical simulation. In this paper, a method for characterizing flow parameters based on pore network model that considers differential pressure flow and diffusion flow is proposed. Firstly, a digital core was reconstructed using focused ion beam scanning electron microscopy (FIB-SEM) from the Gulong shale reservoir in the Songliao Basin, China, and a pore network model was extracted. Secondly, quasi-static single-phase flow and two-phase flow equations considering diffusion were established in the pore network model. Finally, pore throat parameters, absolute permeability, and oil-water two-phase permeability curves were calculated, respectively. The results show that the pore throat distribution of Gulong shale reservoir is mainly concentrated in the nanometer scale, the mean pore radius is 87 nm, the mean throat radius is 41 nm, and the mean coordination number is 3.97; The calculated permeability considering diffusion is 0.000124mD, which is approximately twice the permeability calculated without considering diffusion; The irreducible water saturation of the Gulong shale reservoir is approximately 0.26, and the residual oil saturation is approximately 0.73. The method proposed in this paper can provide an important approach for characterizing the flow parameters of similar shale oil reservoirs.

SOC stock (SOCS) changes caused by land use changes are still unclear, and understanding this response is essential for many environmental policies and land management practices. In this study, we investigated the temporal-spatial and vertical distribution characteristics of SOCS on the Western Sichuan Plateau (WSP) using the sparrow search algorithm-random forest regression (SSA-RFR) models with excellent model applicability and accuracy. The temporal-spatial varia-tions in the SOCS were modeled using 1080 soil samples and a set of nine environmental covariates. We analyzed the effect of land use changes on the SOCS on the WSP. The total SOCS increased by 18.03 Tg C from 1990 to 2020. The results of this study confirmed that the SOCS in the study area has increased significantly since 2010, with an increase of 27.88 Tg C compared to the total SOCS in 2010. We found that the spatial distribution of the SOCS increased from southeast to northwest, and the vertical distribution of the SOCS in the study area decreased with increasing soil depth. Forest and grassland are the main sources of SOCS, the total SOCS in the forest and grassland accounted for 37.53 and 59.39% of the total SOC pool in 2020, respectively. Expansion of the wetlands, forest, and grassland areas could increase SOCS in the study area.

(1) Background: In this work, a series of benzimidazole derivatives containing colchicine-like and cathechol-like moieties with methyl group substitution in the benzimidazole ring were evaluated for their in vitro antiproliferative, pro-apoptotic and antioxidative activity against highly invasive breast cancer cell line MDA-MB-231 and related impairment of tubulin dynamics; (2) Methods: MTT assay was used to evaluate the antiproliferative activity. In vitro tubulin polymerization assay as well as docking analysis was applied to prove the alterations in tubulin polymerization. Immunofluorescent and DAPI staining reveal the pro-apoptotic potential of benzimidazole derivatives and the effect on tubulin’s dynamics in living cells. The antioxidant activity was evaluated by scavenging of H2O2 and hypochlorite ion and ortho-phenanthroline tests; (3) Results: The compounds containing colchicine-like moiety displayed significant growth inhibitory effect against cancer cell line as was highlighted the role of methyl functional group on the tubulin aggregation and blockage of mitosis. All compounds showed an ability to scavenge H2O2, while the compounds with cathecol-like moiety were more effective against hypochlorite ion and chelation of iron; (4) Conclusions: The benzimidazole derivative containing colchicine-like moiety and methyl group substitution in benzimidazole ring is a potential antiproliferative and microtubule destabilizing agent.

We investigated how Artificial Intelligence (AI) reveals factors shaping COVID-19 vaccine hesitancy among healthcare providers by examining their open-text comments. We conducted a longitudinal survey starting in spring of 2020 with 38,788 current and former female nurses in three national cohorts to assess how the pandemic has affected their livelihood. In January and March-April 2021 surveys, participants were invited to contribute open-text comments and answer specific questions about COVID-19 vaccine uptake. A closed-ended question in the survey identified vaccine-hesitant (VH) participants who either had no intention or were unsure of receiving a COVID-19 vaccine. We collected 1,970 comments from VH participants and trained two Machine Learning (ML) algorithms to identify behavioral factors related to VH. The first predictive model classified each comment into one of three Health Belief Model (HBM) constructs (barriers, severity, and susceptibility) related to adopting disease prevention activities. The second predictive model used the words in January comments to predict the vaccine status of VH in March-April 2021; vaccine status was correctly predicted 89% of the time. Our results showed that 35% of VH participants cited barriers, 17% severity, and 7% susceptibility to receiving a COVID-19 vaccine. Out of the HBM constructs, the VH participants citing a barrier, such as allergic reactions and side effects, had the most associated change in vaccine status from VH to later receiving a vaccine.

Honey is a sweet substance extensively consumed in the world for its nutritional and healthy properties. However, residues of pesticides and environmental contaminants can compromise its quality. For this reason, the physicochemical parameters, and the organic contamination of monofloral and multifloral honeys from three regions of Algeria (Tiaret, Laghouat and Tindouf) were monitored to evaluate the quality of honey and the safety for consumers. In general, the results obtained from the physicochemical analyses were in line with the EU standards. In terms of contamination, pesticides authorised and used in Algerian agriculture (matalaxyl-M and cyromazine), as well as banned pesticide (carbaryl), were found in almost all the samples. However, only the concentration of cyromazine was higher than the relative EU maximum residue levels. PCB 180, PCB 189, anthracene, fluorene and phenanthrene were mainly detected. All the honeys show traces of DiBP, DBP, DEHP and DEHT, but no traces of bisphenols were found. Moreover, the dietary exposure assessment shows that a small amount of Algerian honey can be safely consumed. Overall, data from this study should motivate the Algerian government to enhance their monitoring activities in beekeeping and to find solutions for implementing more sustainable agricultural practices harmonizing with the international legislation.

In Cameroon, Aedes mosquitoes transmit various arboviruses, posing significant health risks. We aimed to characterize the Aedes virome in southwestern Cameroon and identify potential core viruses which might be associated with vector competence. A total of 398 Aedes mosquitoes were collected from four locations (Bafoussam, Buea, Edea and Yaounde). Aedes albopictus dominated all sites except for Bafoussam where Aedes africanus prevailed. Metagenomic analyses of mosquitoes grouped per species into 54 pools revealed notable differences in eukaryotic viromes between Ae. africanus and Ae. albopictus, with the former exhibiting greater richness and diversity. Thirty-seven eukaryotic virus species from 16 families were identified, including six novel viruses with near complete genome sequences. Seven viruses were further quantified in individual mosquitoes via qRT-PCR. Although none of them could be identified as core viruses, Guangzhou sobemo-like virus and Bafoussam mosquito solemovirus virus were highly prevalent regionally in Ae. albopictus and Ae. africanus, respectively. This study highlights the diverse eukaryotic virome of Aedes species in southwestern Cameroon. Despite their shared Genus, Aedes species exhibit limited viral sharing, with varying viral abundance and prevalence across locations. Ae. africanus, an understudied vector, harbors a rich and diverse virome, suggesting potential implications for arbovirus vector competence.

Neuron degeneration is the most common old age complications worldwide. Alzheimer's disease (AD) is one of the most common neurodegenerative condition with limited drug options and significant adverse effects. Hence, there is a growing interest in exploring natural products for their potential pharmacological activities against AD. This study investigates the efficacy of Verbesina encelioides flower extract (VFE) in alleviating neurobehavioral damage induced by Scopolamine in rat mimicking AD model. GC-MS analysis showed that V. encelioides flower extract is rich in carotenoids like spirilloxanthin. Various behavioural models were used to assess the rats' learning and memory capabilities. Additionally, biochemical tests were conducted on the AD rat models to evaluate oxidative stress in the brain, including superoxide dismutase (SOD), nitric oxide (NO), reduced glutathione (GSH), and anti-acetylcholinesterase (AChE) enzyme assays. Findings from this study suggest that the VFE significantly improved the rats' cognitive aptitude and alleviated them from oxidative stress by reducing free radical generation. Based on the results obtained from GC-MS analysis, in silico interaction analysis of gingkolide A and spirilloxanthin with acetylcholinesterase was carried out. In summary, this study suggests that V. enceloides flower extract improves learning abilities and mitigates cognitive deficits caused by scopolamine. Thus V. enceloides could be potentially seen as natural therapeutic intervention against neurodegenerative disorders likes Alzheimer’s disease and dementia.

Platelet and fibrin-rich orthobiologic products, such as autologous platelet concentrates, have been extensively studied and appreciated for their beneficial effects in multiple conditions. PRP and its derivatives, including PRF, have demonstrated encouraging outcomes in clinical and laboratory settings, particularly in the treatment of musculoskeletal disorders such as OA. Although PRP and PRF have distinct characteristics, they share similar properties. The relative abundance of platelets, peripheral blood cells and molecular components in these orthobiologic products stimulate numerous biological pathways. These include inflammatory modulation, augmented neovascularization, and delivery of pro-anabolic stimuli that regulate cell recruitment, proliferation, and differentiation. Furthermore, the fibrinolytic system, which is sometimes overlooked, plays a crucial role in musculoskeletal regenerative medicine by regulating proteolytic activity and promoting the recruitment of inflammatory cells and MSCs in areas of tissue regeneration, such as bone, cartilage, and muscle. PRP acts as a potent signaling agent; however, it diffuses easily, while the fibrin from PRF offers a durable scaffolding effect that promotes cell activity. The combination of fibrin with hyaluronic acid, another well-studied orthobiologic product, has been shown to improve its scaffolding properties, leading to more robust fibrin polymerization. This supports cell survival, attachment, migration, and proliferation. Therefore, the administration of the "power mix" containing HA and autologous PRP + PRF may prove to be a safe and cost-effective approach in regenerative medicine.

Retinoblastoma (Rb) is a rare cancer that nonetheless represents the most common ocular malignancy in children. Rb exists as familiar and sporadic cancer and the increasing incidence of the sporadic one and its pathogenesis is mostly unknown. To date the management of retinoblastoma requires intensive chemotherapy and sometimes invasive surgery in order to preserve vision and quality of life in Rb patients. The discovery of the epigenetic nature of non-hereditable/sporadic Rb led to the development of high-throughput precision investigation strategies for the study of its epigenetic landscape. Here we investigated the effect of the demethylating 5-Aza-2’- deoxycytidine (Decitabine; DAC) agent on preclinical models to assess its possible use as anti-cancer drug in the treatment of Rb patients. We found that DAC treatment induced cell cycle arrest and apoptosis in Weri-Rb-1 cells. We investigated the variation of differential gene expression profile in Rb cells in relation to time of exposure to DAC with respect to controls. Network map analysis evidences 15 hub/driver genes, which share pathways of regulation of TNF-, FAS-, p53-dependent apoptotic signaling and NF-kB pro-survival pathways. Furthermore, a computing expression profile analysis of publicly available datasets of patients’ primary tumors and normal retina cell-derived organoids vs WeriWeri-Rb-1 DEGs depicted the relevancy of these 15 hub genes on retinoblastoma genesis. The antiproliferative effect of DAC treatment on Rb was confirmed in vivo, both in subcutaneous xenograft and orthotopic models also showing the changes the gene methylation status in treated Weri-Rb-1, shedding a new light on the reprogramming antiproliferative dynamics induced by the epigenetic therapy and on the role of this therapeutic approach to spare children sight and life.

Although Cable driven rehabilitation devices (CDRD) have advantages over traditional link-driven devices, including lightweight, ease of reconfiguration, remote actuation, etc, the majority of existing lower-limb CDRD is limited to rehabilitation in the sagittal plane. In this work, we extend our previous sagittal plane model (2DOF) to accommodate hip motion in the frontal plane (abduction/adduction) toward studying the feasibility of tracking bi-planar motion (combined frontal and sagittal plane motion) via intra-planar cable routing. Two optimization problems have been formulated to estimate an optimal location of the hip cuffs, first to estimate the optimal cuff location at each time step to identify a single ‘averaged’ optimal cuff location and second to calculate a single optimal cuff location for the entire gait cycle. The optimization solutions identified for the 3DOF model revealed that optimization of the location of cuffs on the anterior and posterior side of the hip joint for 4 cable configuration is not sufficient to generate the desired bi-planar motion. For simultaneous tracking of the bi-planar motion, 2 additional cables have been added at hip joints and are routed in an intra-planar manner. The simulation result with the 3DOF model confirmed successful bi-planar trajectory tracking. The various number of cables and cable routings for tracking bi-planar motion will be studied in future work.

To investigate the effects of organic fertilizer combined with reduced chemical fertilizer on radish yield, quality, and soil environment in high mountainous areas (elevation: 1800 m), and to mitigate the environmental pollution caused by excessive use of chemical fertilizers. The field trial was conducted to study the effects of different fertilizer treatments. (Control:local fertilizer application rate: 375 kg·hm² reduction in chemical fertilizer + 4500 kg·hm² organic fertilizer; T1:12% reduction in chemical fertilizer + 4500 kg·hm² organic fertilizer; T2:20% reduction in chemical fertilizer + 4500 kg·hm² of organic fertilizer; T3:28% reduction in chemical fertilizer + 4500 kg·hm² organic fertilizer). Four different fertilizer ratios were studied to assess their impacts on radish quality, yield, and soil environment. The findings showed that T2 significantly increased radish yield by 12.92%. Moreover, it led to significant improvements in the content of vitamin C, soluble sugars, soluble solids, soluble proteins, titratable acidity, and glucosinolates, which increased by 10.62%, 2.15%, 50.00%, 26.90%, 43.90%, and 44.57%, respectively. Treatment T2 also significantly increased soil nutrient content, with a 7.69% and 14.29% increase in total nitrogen and total phosphorus content compared to the control (Control) treatment, and a significant reduction of 21.64% in soil bulk density . T2 treatment significantly enhanced soil urease activity, sucrase activity, alkaline phosphatase activity, and catalase activity, showing an improvement of 28.97%, 55.92%, 52.08%, and 17.47% compared to the control, respectively (p&lt;0.05). Moreover, treatment T2 resulted in a relative abundance increase of 12.25% and 10.43% in Proteobacteria and Actinobacteria respectively. Thus, the combined application of T2:20% reduction in chemical fertilizer + 4500 kg·hm² of organic fertilizer improved the quality and yield of radish while optimizing the soil environment. T2 effectively promoted radish growth, enhanced radish yield and quality, and improved the soil environment.

The article presents the results of studies aimed to identify the effect of foliar treatments of winter wheat, sugar beets and soybeans with mineral and bioorganic fertilizers. Their positive effect on increasing the concentration of mineral forms of nitrogen in soil was revealed. The crop types have a greater influence on the size of nitrous oxide emissions: in winter wheat crops - 679 µg/m3, soybeans - 637.2 µg/m3, sugar beets - 576.8 µg/m3. The amounts of nitrous oxide emissions were lower in the variants without the use of phosphorus-potassium fertilizers. The Ruter AA fertilizer showed the greatest efficiency on winter wheat crops - 42.7 c/ha. Soybean grain yield of 44.2 c/ha was also achieved by using Ruter AA, as well as Geo-humate together with phosphorus-potassium fertilizers. On the background of the actual supply of phosphorus and potassium, maximum yield was obtained when using N30 on the leaf - 39.3 c/ha. Foliar feeding ensured a yield of sugar beet root crops of up to 67.1-77.4 c/ha on the backdrop of the application of phosphorus-potassium fertilizers with the advantage of using Amino turbo. The largest yield of sugar beet roots without use of mineral phosphorus and potassium was ensured by N30 treatment of the leaf in the phases of 4-6 and 8 leaves - 63.2 t/ha. Of the organo-mineral fertilizers and biostimulants, the best result was shown by the use of Ruter A - 62.6 t/ha. We believe that foliar feeding of crops can be a sustainable farming method that can increase crop yields and reduce N2O emissions.

Background/Objectives: Encouraging results reported of Platelet-Rich Plasma (PRP) treatment for knee osteoarthritis (KOA). The present retrospective study reports the efficacy and safety of a high dose of neutrophile and red blood cell-depleted PRP to treat 212 patients with KOA. Methods: 212 consecutive patients diagnosed with Kellgren-Lawrence (KL) grading 1-3 KOA chronic knee pain for at least 1 year were treated with 3 injections at 15-day intervals with a high dose of neutrophil-depleted PRP (4 billion platelets). Clinical outcomes were retrospectively recorded as a percentage of responders at 3,6, and 12-month follow-up, following the OMERACT-OARSI criteria. Pain through VAS score and WOMAC score have also been recorded. Results: 4ml of PRP containing 4X109 platelets were obtained by single spin centrifugation and injected intra-articular into each patient with no pre-activation. The overall responder rate of patients responding to OMERACT-OARSI criteria at 3,6,12 months was 68.9%, 72,7% and 70,6%. There was a significant improvement in VAS and WOMAC scores at 3-, 6- and 12-month follow-up compared to the pre-treatment value (p&lt; 0.01). The lowest VAS score was observed at 6 months overall and in all three-grade KL groups. KL2 groups showed the best results regarding pain reduction and WOMAC score at 6 months (p&lt; 0.01). Conclusions: a high dose of neutrophil-depleted PRP is an effective treatment for KL1-3 KOA. It provides symptomatic relief, can potentially reduce disease progression, and has sustained effects for up to 12 months.

Particulate organic carbon (POC) is a pivotal component within the marine carbon cycle, actively involved in diverse biogeochemical processes. This study focuses on Mediterranean as the research region, selecting the most influential factors from 47 potential ones influencing surface POC. Using geographic detector for factor identification, ten primary influencers were identified. Preliminarily optimized random forest (BRF), backpropagation neural network, adaptive boosting, and extreme gradient boosting were utilized to construct POC assessment models. Notably BRF exhibited superior performance in estimating the sea surface POC. Further optimization of RF using the tuneRanger R package resulted in R² of 0.868, mean squared error of 1.119 (mg/m³) ², and mean absolute error of 1.041 (mg/m³). Surface POC concentrations in the Mediterranean for May and June 2017 were estimated. Spatial distribution analysis unveiled higher concentrations in the west, lower in the east, higher in the north, lower in the south, with higher levels near the coast and lower far from the coast. Additionally, the study deliberated on the impact of human activities on surface POC in the Mediterranean. This research contributes a high-precision method for satellite retrieval of surface POC concentrations in the Mediterranean, thereby enriching the understanding of POC dynamics in the area.

Promoting organic foods production and consumption contributes to accomplishing United Nations sustainable development goals. Social commerce provides a promising opportunity to develop the organic food industry. However, there is limited knowledge regarding customer behaviors in relation to purchasing organic foods via social commerce platforms. Therefore, this study expanded upon the unified theory of acceptance and use of technology (UTAUT-2) to develop a comprehensive model that explains how customers' social commerce trust and behavioral intentions to purchase organic foods using Instagram social commerce affect their purchasing behaviors. The research model was analyzed by employing partial least squares structural equation modeling (PLS-SEM) for the data collected from a quantitative survey of 410 customers who used Instagram to purchase organic foods in Iran. The results revealed that facilitated purchasing conditions, hedonic motivations, social influence, rating and reviews, and influencers’ endorsements increase customers' purchase intentions. Moreover, Instagram’s recommendations and referrals, influencers’ endorsements, as well as social influence boost customers' trust in the social commerce platform. Eventually, it was determined that influencers’ endorsements, social commerce trust, and purchase intention determine a customer’s organic foods purchasing behaviors. This research provides valuable insights for organic food marketers to optimize their social commerce strategies.

The Gulong shale oil reservoir is formed in freshwater to slightly saline lacustrine basins, mainly consisting of pure shale geological structure, which is quite different from other shale reservoirs around the world. Currently, the development of Gulong shale oil mainly relies on hydraulic fracturing, while the subsequent shut-in period for imbibition has been proven to be an effective method for enhancing shale oil recovery. To clarify the characteristics of fluid occurrence space and the variation of fluid occurrence during saltwater imbibition in Gulong shale, this paper carried out porosity and permeability tests on Gulong shale cores, and analyzed the fluid occurrence space characteristics and imbibition oil recovery based on nuclear magnetic resonance (NMR). In the porosity and permeability tests, the porosity measured by saturation method was calibrated using NMR T2 spectra. Combined with the identification of fractures in shale cores using micro-CT and the analysis of porosity and permeability parameters, it was found that the permeability of shale cores was related to the development of fractures in shale cores. Through the testing and analysis of NMR T1-T2 two-dimensional spectra of the shale cores before and after saturation with oil, it was found that the shale mainly contains heavy oil, light oil, and clay-bound water, and they were distributed in different positions in the T1-T2 spectrum. Finally, the T1-T2 two-dimensional spectra of the shale core at different imbibition stages were analyzed, and it was found that the saltwater mainly entered the minuscule inorganic pores of clay minerals during the imbibition process, and squeezed the larger-sized inorganic pores containing light oil through the hydration expansion effect, thus expelling the light oil from the shale core and achieving the purpose of enhanced oil recovery.

In-situ injection of steam for heating of the subsurface is an efficient method for the recovery of oil and gas from oil shale where permeability typically evolves with temperature. We reported measurements on Jimusar oil shales(Xinjiang, China) at different temperatures to 600℃ and under recreated in situ triaxial stresses to obtain permeability evolution with temperature and stress. Permeability of tight oil shales evolves with temperature to a threshold temperature and peak temperature. The threshold temperature was subjected to triaxial stresses. For Jimusar oil shale, the threshold temperature ranges from 200℃ to 250℃ at ground stress of buried depth of 500m and from 350℃ to 400℃ at buried depth of 1000m. The peak temperature was almost not subjected to triaxial stress and the range is from 450℃ to 500℃ for all Jimusar samples. Pyrolysis plays an important role in permeability evolution and fundamentally changes permeability tendency and magnitude. At high temperature permeability exhibits a little reduction due to stress effect but still remains a high level due to pyrolysis. The above results show that oil shale mass can change from tight porous media into highly permeable media and oil & gas can easily flow through oil shale stratum.

Shale gas production is associated with significant usage of fresh water and discharge of wastewater. Consequently, there is a necessity to create the proper management strategies for water resources in shale gas production and to integrate conventional energy sources (e.g., shale gas) with renewables (e.g., solar energy). The objective of this study is to develop a design framework for integrating water and energy systems including multiple energy sources, cogeneration process, and desalination technologies in treating wastewater and providing fresh water for shale gas production. Solar energy is included to provide thermal power directly to a multi-effect distillation plant (MED) exclusively (to be more feasible economically) or indirect supply through a thermal energy storage system. Thus, MED is driven by direct or indirect solar energy, and excess or direct cogeneration process heat. The proposed thermal energy storage along with the fossil fuel boiler will allow for the dual-purpose system to operate at steady-state by managing the dynamic variability of solar energy. Additionally, electric production is considered to supply a reverse osmosis plant (RO) without connecting to the local electric grid. A multi-period mixed integer nonlinear program (MINLP) is developed and applied to discretize operation period to track the diurnal fluctuations of solar energy. The solution of the optimization program determines the optimal mix of solar energy, thermal storage, and fossil fuel to attain the maximum annual profit of the entire system. A case study is solved for water treatment and energy management for Eagle Ford Basin in Texas.

The escalation of mining activities in the karst regions of Guizhou Province has heightened the occurrence of water-inrush incidents in deep coal mines. This study focused on water-inrush phenomena within the Xinhua mining area of Jinsha County, Guizhou Province, aiming to investigate the sources of these incidents. The findings indicated that the overlying limestone of the Changxing Formation in the coal seam served as a vulnerable aquifer under certain conditions, leading to water inrushes. The analysis of the spatiotemporal distribution patterns of water-inrush incidents at the working face indicated that previous mining operations damaged the shallow Changxing Formation limestone, resulting in the accumulation of goaf water and the formation of numerous mining-induced fractures. These fractures served as rapid conduits for water inrushes from both atmospheric precipitation and underground sources at the deep working face. The examination of surface water and mine water quality demonstrated that both exhibited similar characteristics, predominantly featuring bicarbonate, sulfate, and sodium compositions. Investigation into the relationship between mine water inflow and atmospheric precipitation established that atmospheric precipitation influenced the mine water supply cycle, with a replenishment period of ~10 months during the operational phase of the Jinyuan Coal Mine and about one month post-closure. The fractures induced by mining activities within the Changxing Formation limestone facilitated water flow, with atmospheric precipitation serving as the primary water source for the mine. This study offered a valuable scientific foundation for addressing water-related damage resulting from atmospheric precipitation in mines susceptible to water inrushes under analogous hydrogeological conditions.

A field experiment was conducted for 2 years in Green Tea Laboratory of Saitama Prefectural Agriculture and Forestry Research Center, Iruma, Saitama, Japan from March 2014 to December 2015. Controlled release fertilizers (CRF) or organic fertilizers (ORG) which is the mixture of chicken manure and oil cakewere applied with the amount of 450 kg N ha^-1 yr^-1 in 2014 and 397 kg N ha^-1 yr^-1 in 2015. Nitrous oxide (N₂O) emissionsfrom soil in green tea fields were measured by closed chamber method. The results showed that CRF has significantly lower N₂O compared to ORG. The cumulative N₂O emissions from CRF accounted for 51% of N₂O emissions from ORG fields and 138% of control with no fertilizer treatment. The N₂O flux from the row was higher than that of under the canopy, since fertilizer were applied on the row. However the total emission from the area between the rows was lower than that under the canopy because of the area ratio of row and canopy was 1:5.

The erosion of surface pipelines induced by proppant flowback during shale gas production is significant. The surface pipelines in a shale gas field in the Sichuan Basin experienced perforation failures after only five months of service. To investigate the erosion features of L360N, coatings, and ceramics and optimize the selection of two protective materials, a gas-solid two-phase flow jet erosion experimental device was used to explore the erosion resistance of L360N, coating, and ceramic under different impact velocities (15 m/s, 20 m/s, and 30 m/s). An energy dispersive spectroscope, a scanning electron microscope, and a laser confocal microscope were employed to analyze erosion morphologies. With the increase in flow velocity, erosion depth and erosion rate of L360N, coating, and ceramic increased and peaked under an impact velocity of 30 m/s. Maximum erosion rate and maximum erosion depth of L360N were respectively 0.0350 mg/g and 37.5365 µm. Its primary material removal mechanism was plowing of solid particles and microcracks were distributed on the material surface under high flow velocities. Maximum erosion rate and maximum erosion depth of coating were respectively 0.0217 mg/g and 18.9964 µm. Its primary material removal mechanism was the detachment of the binder phase Co caused by plowing. Maximum erosion rate and maximum erosion depth of ceramics were respectively 0.0108 mg/g and 12.4856 µm. The erosion mechanisms were micro-cutting and plowing. Under different particle impact velocity, different erosion morphologies were observed, but the primary erosion mechanism was the same. The erosion resistance of ceramics was higher than that of coating. Therefore, ceramic lining materials could be used to protect the easily eroded parts, such as pipeline bends and tees, and reduce the failure rate by more than 93%. The study provided the data and theoretical basis for the theoretical study on oil and gas pipeline erosion and pipeline material selection.

More than 700 anthocyanins are described so far, and many different sources are rich in these natural pigments. During the last few years, researchers have been focusing of strategies to recover and purify anthocyanins, from simple liquid-liquid extractions to more advanced supercritical CO2 extractions, however, with such a huge number of different sources, it’s extremely hard to get a simple and fast methodology that fits several sources, not only by the structural nature of the anthocyanins but also by the presence of specific groups of natural compounds. Using simple methodologies like solid-phase extraction resins represents a powerful economical and efficiency strategy. In this work, we tested several sources of structurally distinct anthocyanins, including purple basil, purple cabbage, purple sweet potato, butterfly pea flower, cornflower and wild pansy, in different resins to assess their efficiency in the obtention of anthocyanin-pure extracts. The results showed us that the combination of oasis HLB® resin followed by a cation-exchange SPE with DSC-MCAX® resulted in high-purity anthocyanin extracts for all the cases.

A 2-month incubation study was carried out using two soil types to determine nitrogen mineralization of different inorganic-organic amendments. The following seven treatments (T) were established; T1 = control, T2 = 5 g of dry algae per kg of soil (100%DA), T3 = 136g of agri-mat per kg of soil (100%GA), T4 = 61 g of ground grass per kg of soil (100%GG), T5 = 2.5 g of dry algae + 2.5 g of nitrogen fertilizer (NF) per kg of soil (50%DA50NF), T6 = 50%GA50NF, T7 = 50%GG50NF. Three samples per treatment were drawn at 0, 3, 7, 15, 30, 45, and 60 days for mineral-N determination. A 2-month glasshouse experiment was established afterwards with the following five treatments: T1 = Control, T2 = 50%DA, T3 = 50%GA, T4 = 50%GG, and T5 = 100NF. The results indicated that nitrogen mineralization was significantly higher in organic-inorganic amendments compared to sole organic amendments. The percentage differences ranged from 157% to 195%. The 50%DA treatment increased spinach yield by 20.6% in sandy loam and 36.5% in loam soil. It is difficult to fully recommend the 50%DA treatment without field-scale evaluation, but it is a promising option to be considered.

This work aimed to synthesize new N-rich triazole compounds. In this article we describe the synthesis of three different 1,2,4-triazole-based systems starting from 1,3-diaminoguanidine hydrochloride monohydrate. The structure of the obtained crystals was established by single-crystal X-Ray diffraction. The high nitrogen content of the synthetized compounds makes them building blocks for the application in the High-Energy-Density material science.

The aim of this study was to compare the effect of using L-PRF in patients undergoing impacted lower third molar surgery with either primary or secondary closure techniques. Methods: This prospective, randomised, double-blind, split-mouth clinical trial was conducted in patients with bilateral lower impacted third molars of similar position. Primary closure was performed in group 1 and secondary closure in group 2. Group 1 closure technique was applied to one side of the patients and group 2 closure technique was applied to the other side at different times. Nine pa-tients were excluded from the study due to alveolitis and failure to attend regular control visits out of the 45 patients evaluated. Results: Of the 36 patients included in the study, 23 were female and 13 were male and the mean age was 22.42±3.36 years. The secondary closure group had lower VAS scores at hour 6 (p

Abstract: Kiwifruit, a perennial horticultural crop known for its nutritional value, faces significant challenges due to biotic and abiotic stresses, affecting its yield and quality. Leucine-rich repeat receptor-like proteins (LRR-RLPs), a major group of receptor-like proteins in plants, have diverse functions in plant physiology, including growth, development, signal transduction, and stress responses. Despite their importance, the specific roles of kiwifruit LRR-RLPs in response to biotic and abiotic stresses remain poorly understood. In this study, we investigated the expression patterns of kiwifruit LRR-RLPs under various stress conditions, including pathogen stress, heat stress, waterlogging stress, and copper stress. Through genome and transcriptome analyses, we identified a total of 101, 164, and 105 LRR-RLPs in Actinidia Chinensis 'Hongyang', Actinidia eriantha 'Huate', and Actinidia chinensis 'Red5' kiwifruit, respectively, classified into 9 subgroups based on phylogenetic relationships. Synteny analysis revealed that the expansion of kiwifruit LRR-RLPs was primarily attributed to segmental duplication events. Using RNA-seq data from pathogen-infected kiwifruits, we identified specific LRR-RLP genes potentially involved in different stages of pathogen infection. Additionally, we observed the potential involvement of kiwifruit LRR-RLPs in abiotic stress responses, with upstream transcription factors possibly regulating their expression. Furthermore, protein interaction network analysis unveiled the participation of kiwifruit LRR-RLP genes in the regulatory network of abiotic stress responses. These findings highlight the crucial roles of LRR-RLPs in mediating both biotic and abiotic stress responses in kiwifruit, offering valuable insights for the breeding of stress-resistant kiwifruit varieties.

It’s well known that existing horizontal well drilling and hydraulic fracturing technology that is used to achieve large-scale cost-effective production from immature to low-moderate maturity continental shale in China, where the organic matter mainly exists in the solid form is fairly ineffective. To overcome the obstacles, in-situ conversion technology seems feasible, while implementing it in the target layer along with estimating the amount of expected recoverable hydrocarbon in such shale formations seems difficult. This is because there is no guideline to choose the most appropriate method and select relevant key parameters for this purpose. Hence, based on thermal simulation experiments during the in-situ conversion of crude oil from the Triassic Chang 73 Formation in the Ordos Basin and the Cretaceous Nenjiang Formation in the Songliao Basin, this deficiency in knowledge was addressed. First, relationships between the in-situ converted total organic carbon (TOC) content and the vitrinite reflectance (Ro) of the shales and between the residual oil volume and the hydrocarbon yield was established. Second, the yields of residual oil and in-situ converted hydrocarbon were measured, revealing their sensitivity to fluid pressure and crude oil density. In addition, a model was proposed to estimate the amount of in-situ converted hydrocarbon based on the TOC, hydrocarbon generation potential, Ro, residual oil volume, fluid pressure, and crude oil density. Finally, a method was established to determine key parameters on the final hydrocarbon yield from immature to low-moderate maturity organic material during in-situ conversion in shales. Following the procedure outlined in this paper, estimated recoverable in-situ converted oil in the shales of the Nenjiang Formation in the Songliao Basin was estimated to be approximately 292×108 tons, along with 18.5×1012 cubic meters of natural gas, in an area of approximately 8×104 square kilometers. Collectively, the method developed in this study is independent from the organic matter type and other geological and/or petrophysical properties of the formation and can be applied to other areas globally where there isn’t any available in-situ conversion thermal simulation experimental data.

We replace the current industry-standard empirical forecasts of oil production from hydrofractured horizontal wells in shales with a statistically and physically robust, accurate and precise approach, using the Bakken shale as an illustration. The proposed oil production forecasting method extends our previous work on predicting fieldwide gas production in the Barnett shale and merges it with our new scaling of oil production in shales. We first divide the existing 14,678 horizontal oil wells in the Bakken into 12 static samples in which depositional settings and completion technologies are similar. For each sample, we construct a purely data-driven P50 well prototype by merging the GEV distribution fits of oil production from appropriate well cohorts. We fit the parameters of our physics-based scaling curve to the statistical well prototypes, and obtain their smooth extrapolations to 30 years on production. By calculating the number of potential wells of each Bakken region, and scheduling future drilling programs, we stack up the extended well prototypes to achieve the most plausible forecast. We predict that Bakken will ultimately produce 5 billion barrels of oil from the existing wells, with the possible increments of 2 and 6 billion barrels from core and noncore areas.

This paper concerns the effect of proppant embedment related with hydraulic fracturing treatment. This phenomenon occurs if the strength of the reservoir rock is lower than proppant grains. The aim of the research is laboratory determining the loss of width of the proppant pack built of light ceramic grains. The laboratory simulation of the embedment phenomenon was carried out for a shale rock on a hydraulic press, in a specially prepared for this purpose a heated embedment chamber. Tests were conducted at high temperature and axial compressive stress conditions. The surfaces of the cylindrical core plugs (fracture faces) were imaged under an optical microscope equipped with 3D software. The fracture faces were examined and compared before and after the embedment phenomenon. The analysis of the obtained images of the fracture face were made based on the research method of the embedment phenomenon developed at Oil and Gas Institute-NRI. On the basis of laboratory tests, the parameters characterizing the embedment phenomenon were collected and discussed. In addition, the percentage reduction in the width of the proppant pack was determined.

Innovations and improvements in hydraulic fracturing and horizontal well technologies have contributed to the success of the shale gas industry; however, the industry is also challenged by freshwater use and environmental health issues. Increasing water impact makes precise quantification of water consumption important. The objective in this study was to better understand water sustainability and availability of the projected shale gas from 2018 to 2030 in the Weiyuan play, China. The water footprint framework was used to quantify the potential water use and environmental impacts on different time scales. The results showed that the water use per well ranged from 11351.3 to 60664.73 m3, with a median of 36013.94 m3, totaling ~3.44 Mm3 for 97 wells. Yearly evaluation results showed that the gray water footprint was the main contributor and accounted for 83.82% to 96.76%, which was dependent on different scenarios of treatment percentages. The monthly environmental impact results indicated that the annual streamflow statistics were more likely to prevent water withdrawal. Water quality issues may be alleviated through recycling and retreatment measures that improve current waste water management strategies. Resource regulators should manage their water resources by matching water demand to water availability or replenishment.

Autologous platelet-rich plasma (PRP) preparations are prepared at point of care. Centrifugation cellular density separation sequesters a fresh unit of blood into three main fractions: a platelet-poor plasma (PPP) fraction, a stratum rich in platelets (platelet concentrate) and, bioformulation dependent, also leukocyte and erythrocyte fractions. The employment of autologous platelet concentrates facilitates the biological potential to accelerate and support in numerous cellular activities that can lead to tissue repair, tissue regeneration, wound healing, and ultimately functional structural repair. Normally, after PRP preparation the PPP fraction is discarded. One of the less well known, but equally important features of PPP is that particular growth factors (GFs) are not abundantly present in PRP, as they reside outside the platelet alpha granules. Precisely, insulin-like growth factor-1 (IGF-1) and hepatocyte growth factor (HGF) are mainly present in the PPP fraction. In addition to their roles as angiogenesis activators, these plasma-based GFs are also known to inhibit inflammation, fibrosis, and they promote keratinocyte migration and support in tissue repair and wound healing. Additionally, PPP is known for the presence of exosomes and other macrovesicles, exerting cell-cell communication and cell signaling. Newly developed ultrafiltration technologies incorporate PPP processing methods by eliminating in a fast and efficient manner plasma water, cytokines, molecules, and plasma proteins with a molecular mass (weight) less than the pore size of the fibers. Consequently, a viable and viscous protein concentrate of functional, total proteins, like fibrinogen, albumin, and alpha-2-macroglobulin is created. Consolidating a small volume of high platelet concentrate with a small volume of highly concentrated protein-rich PPP creates a protein rich platelet concentrate (PRPC) biological preparation. After the activation of proteins, mainly fibrinogen, the PRPC matrix retains and facilitates interactions between invading resident cells, like macrophages, fibroblast, and mesenchymal stem cells (MSCs), and the embedded concentrated PRP cells and molecules. The administered PRPC biologic will ultimately undergo fibrinolysis, leading to a sustained release of concentrated cells and molecules that have been retained in the PRPC matrix until the matrix is dissolved. We will discuss the unique biological and tissue reparative and regenerative properties of PRPC matrix.

Competency frameworks outline the perceived knowledge, skills and other attributes required for professional practice. Competency frameworks have gained in popularity, in part for their ability to inform health professions education, assessment, professional mobility, and other activities. Previous research has shown inadequate reporting within reports describing their development and that may jeopardize their use and application. We aimed to develop a set of minimum criteria that provides guidance to authors (and consumers) in an effort to improve reporting of the development of competency frameworks. The checklist was developed by a 35-member expert panel and a five-member research team following published guidance from the Enhancing the QUAlity and Transparency Of health Research (EQUATOR) Network. The final checklist contains 20 essential reporting items including guidance on reporting title and abstract, framework development, the development process, testing and funding/conflicts of interest. The intent of the COmpeteNcy FramEwoRk Development in Health Professions (CONFERD-HP) reporting guideline is to help readers (including researchers, educators, regulators, health professionals, and patients) develop a greater understanding of relevant terminology, core concepts, and key items to report for competency framework development in health professions.

The role of foods is shifting from focusing on the provision of energy and basic nutrients to also include bioactive compounds that prevent the development of chronic age-related diseases. Mi-croalgae offer a source of nutritional compounds with important health effects, and have the po-tential for production of health-promoting products, without increasing agricultural land use and negatively impacting the environment. Here we investigate the health effects of microalgal ex-tracts with high levels of the colourless carotenoid phytoene. Phytoene is widely available from dietary sources and can be detected across different tissues in the human body. However, it is usually regarded as a precursor for the synthesis of other carotenoids, rather than a bioactive molecule. We utilised the model organism C. elegans to show that phytoene-rich extracts from Chlorella sorokiniana and Dunaliella bardawil have anti-ageing properties. The extracts protect against oxidative damage and amyloid-β42 proteotoxicity (a major pathology of Alzheimer's disease), and extends lifespan. We show that pure phytoene also has these anti-ageing effects, suggesting that phytoene is a bioactive molecule with positive effects on ageing and longevity.

.Maize cultivation in Thailand faces challenges owing to climate change and soil organic carbon (SOC) loss. This highlights the importance of comparing maize soil with paddy soil in terms of the role of dissolved organic carbon (DOC) and nutrient availability, as they influence SOC content. Soil samples from Chiang Mai province, primarily Fluvisol, were collected for the cultivation of paddy rice and maize, analysed for carbon fractions and chemical properties, and categorised into layers. Comparative analysis revealed that maize soils had lower levels of labile carbon components and organic carbon than paddy soils (P

Natural and sustainable plant-based antioxidants and antimicrobials are highly desirable for improving food quality and safety. The present investigation assessed the antimicrobial and antioxidant properties of active components from Alkanna tinctoria (herb) roots, also known as Ratanjot root. Two methods were used to extract active components: microwave-assisted hot water (MAHW) and ethanol and air-dried. MAHW extract yielded 6.29% while the ethanol yielded 18.27%, suggesting superior Ratanjot root extract powder (RRP) solubility in ethanol over water. The ethanol extract showed significantly higher antioxidant activity than the MAHW extract. Gas chromatography and mass-spec analysis revealed three major phenolic compounds: Butanoic acid, 3-hydroxy-3-methyl-; Arnebin 7, and Diisooctylpthalate. The color attributes (L*, a*, b*, hab, C*ab) for the ethanolic and MAHW extracts revealed significant differences (P < 0.05) in all the above parameters for both types of extracts, except for yellowness (b*) and chroma (C*ab) values. The ethanol extract exhibited antimicrobial activity against 14 bacterial species, with a signifi-cantly higher inhibitory effect against Gram-positive bacteria (Listeria monocytogenes and Staphylococcus aureus) than the Gram-negative bacteria (Salmonella enterica serovar Typhimurium and Escherichia coli). The minimum inhibitory concentration (MIC) and minimum bactericidal concentration (MBC) were both 25 mg/ml for the Gram-negative bacteria, while the MIC and MBC concentrations varied for Gram-positive bacteria (0.049 - 0.098 mg/ml and 0.098 - 0.195 mg/ml) and the antimicrobial effect was bactericidal. The antimicrobial activities of RRP extract remained stable under broad temperature (37-100°C) and pH (2-6) conditions, as well as during refrigerated storage for 30 days. Application of RRP at 1% (10 mg/g) and 2.5% (25 mg/g) levels in a cooked chicken meatball model system prevented lipid oxidation and improved sensory attributes and retarded microbial growth during refrigerated (4°C) storage for 20 days. Furthermore, the RRP extract was non-toxic when tested with sheep erythrocytes and did not inhibit the growth of probiotics, Lacticaseibacillus casei, and Lactiplantibacillus plantarum. In conclusion, the study suggests that RRP possesses excellent antimicrobial and antioxidant activities, thus making it suitable for food preservation.

Byers Peninsula is considered one of the largest ice-free areas in Maritime Antarctica. Since 2006, the Spanish Polar Program has taken part in a large number of environmental studies involving effects of climate changes in lives cycles, limnology and microbiology. Soils from maritime Antarctica are generally weakly developed and have chemical, physical and morphological characteristics strongly influenced by the parent material. However, biological activity during the short Antarctic summer promotes intense transference of nutrients and organic matter in areas occupied by different species of birds and marine mammals. To mapping and monitoring those areas with high biological occupation, could be very useful to have models of edaphic properties prepared from satellite images. In this approach, Deep Learning and Linear Regression models of soil properties and spectral indexes as explicative variables were performed. We training models of soil properties closely related to biological activity such as Dissolved Organic Carbon (DOC) and the iron fraction associated with organic matter (Fe). We tested the best approach to model the spatial distribution of DOC, Fe and pH by training models of Linear Regression and Deep Learning over Sentinel2 and WorldView2 images. The most robust models were used to track possible areas with ornithogenic soils as well as areas of the Byers Peninsula that could support the highest biological development.

The new hybrid composite materials for PEM fuel cell were synthesized by UV-polymerization of acrylic monomers (acrylonitrile (AN), acrylic acid (AA), ethylene glycol dimethacrylate (EGDMA)) and sulfo aromatic monomer – sodium styrene sulfonate (SSS), and tetraethoxysilane/3-methacryloxypropyltrimethoxysilane (TEOS/MAPTMS)-based sol-gel system. By means of X-ray spectroscopy fractal structure of the obtained materials was characterized. Proton conductivity and viscoelastic properties of the materials were investigated depending on the content of inorganic component in nanocomposites. On the basis of impedance studies, an equivalent scheme is proposed that successfully describes the proton conductivity in the synthesized composite electrolyte membranes.

Plants from the Myrtaceae family are well known to contain considerable amounts of volatile compounds, ranging from oxygenated monoterpenes to hydrogenated sesquiterpenes, and others, which exhibit antimicrobial activity. One such plant includes Syzygium aromaticum that has been extensively used to treat a number of disorders, including bacterial and fungal infections. Thus, the scientific validation of the essential oil (EO) of Syzygium aromaticum vis-à-vis Candida and Cryptococcus species is valuable. To this end, the present study sought to investigate the antifungal activity of EO from S. aromaticum (clove) leaves and flower buds against Candida and Cryptococcus species. The antioxidant activity of S. aromaticum’s essential oils is also elucidated. The EO was extracted from fresh leaves and floral buds of S. aromaticum using a Clevenger-type apparatus. The as-prepared essential oils were further evaluated for antifungal activity against Candida and Cryptococcus species using a microdilution method. The phytochemical analysis of the EOs was assessed by gas chromatography/mass spectrometry (GC-MS). Antioxidant activities of the EOs were evaluated using standard methods. As a result, the GC-MS analysis revealed the presence of volatile compounds, such as eugenol (87.08%), β-caryophyllene (6.40%) and acetyleugenol (4.45%) as the major constituents of EO from the flower buds ; and eugenol (90.54%) and β-caryophyllene (24.65%) as the major components of the leaf’s EO. The eugenol-rich essential oils exhibited significant antifungal effects against Candida species (common MIC value: 200 ppm) and Cryptococcus neoformans (MIC value: 50 ppm), as well as antioxidant activity. Overall, essential oils of S. aromaticum demonstrated an-tioxidant and antifungal effects, thus validating the ethnopharmacological use of this plant in the treatment of fungal infections. However, antifungal mechanisms of action, in-depth toxicity and in vivo experiments, and pharmacokinetics are warranted to support the use of this plant in ethnomedicine.

To evaluate the nutrient load due to the grazing of laying hens in outdoor runs, soil characteristics were monitored in three Italian organic farms. For each farm, soil samples were taken from three increasing distances from the hen house and two depths and different chemical parameters were evaluated. The comparison among the results from the different distances shows that N-NO3 and Olsen P are the most affected parameters by hen faeces: both present high values with a statistically significant difference in the area close to the poultry house and for the most superficial layer. Even TKN and TOC show significant differences between the concentrations of the first layer (more concentrated) and those of the second layer (less concentrated). In general, the surface soil layer closest to the chicken house is the portion of the outdoor run most affected by chicken droppings and represents the most critical point in terms of potential environmental impact. Therefore, it is necessary to intensify the management of the outdoor run with tools that can facilitate the grazing of animals and with vegetation that can absorb nutrients by limiting leaching and run-off.

Exploration practices have proven that over mature shale gas exhibits a feature of carbon isotope reversal. The geochemical statistics indicate that the wetness (C2-C5/C1-C5) of shale gas with carbon isotope reversal is less than 1.8%. In addition, the magnitude of carbon isotope reversal (δ13C1- δ13C2) for the over mature shale gas presents a parabolic variation with decreasing wetness. δ13C1-δ13C2 increases with decreasing wetness within a wetness range of 0.9% ~1.8% and then decreases with decreasing wetness at wetness < 0.9%. The CH4 cracking experiment demonstrates that CH4 polymerization occurring in the early stage of CH4 cracking is an important factor involved in isotope reversal of over mature shale gas. Moreover, δ13C1- δ13C2 decreases with an increase in experimental temperature prior to CH4 substantial cracking. The values of δ13C1 and δ13C2 tend to equalize during CH4 substantial cracking. The δ13C1-δ13C2 of mud gas present at different depths during shale gas drilling in Sichuan Basin increases initially, then decreases with further increase in the depth and finally tends to zero, with only a trace hydrocarbon gas being detectable. Statistical data suggests that the shale gas production in Sichuan Basin decreases with the decreasing δ13C1-δ13C2 value and wetness. Thus, δ13C1-δ13C2 and wetness could potentially serve as useful criteria to screen CH4 cracking degree and to determine the largest depth of natural gas exploration. Great care should be taken during shale gas exploration in deeper layers, with wetness and δ13C1-δ13C2 less than 0.2% and 1%, respectively, since very low wetness (<0.2%) and δ13C1-δ13C2 (<1%) might be indicative of CH4 substantial cracking in a geological setting.

The effect of land use on sandy soils of southern Botswana was carried out by comparing the composition and properties of soil organic matter. Virgin and disturbed soils were sampled from savanna ecosystems (Central District and Kweneng District). The biodegradability of organic matter was evaluated by incubation in the laboratory. Humic fractions were quantified and humic acids were analyzed by visible and infrared spectroscopy. The results indicate that continued disturbance, whether due to grazing or subsistence farming, has resulted in small significant changes in the concentration of available nutrients and organic matter in the soil. Nevertheless, substantial changes could be established in soil C/N ratio, humic acid/fulvic acid ratio and in the biodegradability of soil organic matter and the structural characteristics of humic acids. The increased aromaticity of humic acid (visible and IR spectroscopies) following disturbance, suggests increased biogeochemical activity and/or the impact of abiotic processes (such as periodic fires) selectively removing aliphatic constituents. The overall results indicate a low potential soil fertility, the sustainable preservation of which depending more on features related to quality than to the total amount of the soil organic matter, which shows considerable aromatization parallel to its degree of association with the mineral fraction.

p-Toluenesulfonic acid is commercially available, non-toxic, cheap organic compound with robust stability. p-Toluenesulfonic acid is solid, non-corrosive and a strong organic acid that can be handled easily. Due to this p-toluenesulfonic acid could be the better replacement of other conventional acids like nitric acid, sulfuric acid, perchloric acid and AlCl3 in organic transformations. Moreover, p-toluenesulfonic acid could be used synergistically with other mode of catalysis like transition metal catalysis and photocatalysis. In recent years, the use of this solid organic acid in organic and polymer synthesis has grown tremendously. In this review, we present an overview of p-toluenesulfonic acid promoted various organic reactions with particular emphasis to the more recently reported methods. In some cases, we also detailed the understanding of the reactions by providing the reaction mechanism. Despite these advances, there are still many opportunities for the development of new reactions using PTSA. Industry and academia have become more conscious to adopt sustainable chemical processes using safer reagents and solvents and the use of PTSA in this context is highly significant. This review will inspire researchers for further reaction development employing p-toluenesulfonic acid.

Crop rotation diversification using legumes has been advocated as one of the solutions to improve the resilience of the crop system to various environmental stresses and the use of nitrogen resources. However, when forage legumes or grass-legumes are ploughed, there is a high risk of nitrate leaching, especially in sandy soils. The aim of the study was to determine the effect strip tillage intercropping management on soil mineral nitrogen (SMN), water-extractable organic carbon (WEOC) content and winter wheat (WW, Triticum aestivum L.) grain yield compared to forage legume and WW monocropping with conventional tillage. In intercropping was used winter wheat - black medick (Medicago lupulina L.) WW+BM, winter wheat - white clover (Trifolium repens L.) WW+WC, and winter wheat - Egyptian clover (Trifolium alexandrinum L.) WW+EC. Research was repeated in two experiments. The results showed that after strip tillage and WW sowing less or similar SMN content cud be detected, as in conventional tillage and WW + forage legumes intercropping. WW grain yield in intercrops decreased, compared to the grasses monocultures that were ploughed before WW sowing. The highest amount of WEOC was in intercropping soil growing WW+WC or in all fields (except WW+EC) after applying strip tillage. During the research period, the amounts of mobile humic substances (HSs) and mobile humic acids (HAs) changed analogously. Their content increased substantially in fields with WC and EC, regardless of whether the grasses were ploughed or grown with WW.

In recent years, long periods of drought and heat waves have become increasingly frequent, causing forest dieback phenomena that make stands more sensitive to biotic stressors. How trees may respond to extreme climatic events and which metabolites are involved under stress conditions is still not clear. In this study, we analysed by SPME how dieback (D) and non-dieback (ND) Hungarian oak trees from the San Paolo Albanese site respond to these climatic dynamics, in terms of volatile organic compounds (VOCs). For each group of trees, three wood samples were taken, each divided into four sub-samples with 5 growth rings, subjected to SPME and increase in basal area (BAI) analysis of the last 20 years. Dieback trees had a lower amount of leaves, and this condition may translate into less photosynthesis, less organic matter production and lower reserves of carbohydrates available for growth. Indeed, D trees showed lower radial increases and a lower content of aldehydes, terpenes, and fatty acids than ND trees, indicating a better health of ND trees compared to D trees. While D trees showed a reduction in terpenes, such as α-pinene, γ-eudesmol, and cyperene (with significant insecticidal activity), a reduction in aromatic aldehydes, such as furfural and 5-methylfurfural, and an increase in silanols (with antimicrobial function). Considering the different compounds’ contents between D and ND trees, our study could be useful for detecting bio-indicators to identify an early warning signal of dieback phenomena.

Soil organic matter (SOM) is essential for nutrient cycling and soil carbon (C) accumu-lation, both of which are heavily influenced by the quality and quantity of plant litter. Since SOM dynamics in relation to plant diversity are poorly understood we investigated the effects of willow variety and mixture, and site on the soil C stocks, SOM chemical composition and ther-mal stability. Using pyrolysis-field ionization mass spectrometry we analysed the top 10 cm of soil from two 7-year-old experimental sites in Germany and Sweden, with monocultures and mixtures of two willow varieties (Salix spp.) belonging to different species. Overall, site had the strongest effect on SOM quality. Results showed significant variability across sites for willow identity and mixture effects on C accumulation and SOM chemistry. In the German site (Ros-tock), yearly soil C accumulation was higher (p < 0.05) for variety ‘Loden’ (1.0 Mg C ha-1 year-1) compared to ‘Tora’ (0.5 Mg C ha-1 year-1), whilst in the Swedish site (Uppsala), both varieties ex-hibited similar soil C accumulation rates of around 0.6 Mg C ha-1 year-1. Willow variety identity significantly affected SOM quality at both sites, while mixing had minor effects. Our findings emphasize the significance of site-specific context and variety or species identity in shaping soil C accumulation in willow plantations.

The study involved a comparison of the chemical, physical, microbiological, and functional attributes of must extracted from Solaris cultivar grapes cultivated under both conventional and organic farming systems. This study aimed to determine the influence of cultivation methods on various must properties, including the levels of health-promoting polyphenols and health-threatening mycotoxins and pesticide residues. It was observed that the organic grapes hosted a greater diversity and quantity (OTUs) of bacteria and fungi. The predominant bacteria were Sphingomonas (with similar numbers in both crops) and Massilia (more abundant in grapes from the conventional crop). These two bacterial groups collectively accounted, on average, for about 40% of all OTU sequences detected. Lower levels of bacteria of the genera Hymenobacter and Pseudomonas and others colonized the grapes. Among the fungi, Erysiphe and Aureobasidium were dominant, comprising about 50–70% of all detected taxa. Notably, Erysiphe was predominantly found in conventionally grown grapes, while Aureobasidium, Mycosphaerella, and Botryotinia were present in comparable quantities in fruit from both types of crops. No mycotoxins were detected in the must or marc, despite the presence of genes responsible for aflatoxin and ochratoxin biosynthesis in both types of grape juice. The organic must exhibited significantly higher levels of polyphenols and displayed improved antioxidant properties and technological characteristics. Moreover, sulfur and copper used in the protection of the organic plantation passed from the fruit surface into the must. Also, pesticide residues, namely cyprodinil and fludioxonil from conventional cultivation, were detected in the must.

In this study, by employing the think-aloud model, schema theory and the perceptual cycle model (PCM) from the perspective of vulnerable road traffic participants, the current traffic imperfections of a target section in Wudaokou were analyzed to explore potential improvement measures to enhance safety. Specifically, the present study recruited 30 local volunteers, which were equally divided into a pedestrian group, bicyclist group and E-cyclist group. The research procedure was mainly divided into three steps. By using the think-aloud method, we analyzed and recorded the contents of oral reports of the experimental road section. Then, through translation, segmentation, coding, analysis and other techniques, we sorted and studied the report data and drew a conclusion that was universal in improving the current road traffic conditions. It is hoped that through this study, on the one hand, the applicability of the oral report method, schema theory and perceptual cycle model in road traffic safety can be verified, and, on the other hand, some better improvement measures can be extracted for the road traffic state of the Wudaokou section.

Enteroviruses (EV) are important pathogens causing human disease with various clinical manifestations. To date, treatment of enteroviral infections is mainly supportive since no vaccination or antiviral drugs are approved for their prevention or treatment. Here, we describe the antiviral properties and mechanisms of action of leucoverdazyls - novel heterocyclic compounds with antioxidant potential. The lead compound, 1a, demonstrated low cytotoxicity along with high antioxidant and virus-inhibiting activity. A viral strain resistant to 1a was selected, and the development of resistance was shown to be accompanied by mutation of virus-specific non-structural protein 2C. This resistant virus had lower fitness when grown in cell culture. Taken together, our results demonstrate high antiviral potential of leucoverdazyls as novel inhibitors of enterovirus replication and support previous evidence of an important role of 2C proteins in EV replication.

A recent study by the Wall Street Journal reveals that the hydrofractured horizontal wells in shales have been producing less than forecasted by the industry with the empirical hyperbolic decline curve analysis (DCA). As an alternative to DCA, we introduce a simple, fast and accurate method of estimating ultimate recovery (EUR) in oil shales. We adopt a physics-based scaling approach to analyze oil rates and ultimate recovery from 14,888 active horizontal oil wells in the Bakken shale. To predict EUR, we collapse production records from individual horizontal shale oil wells onto two segments of a master curve: (1) We find that cumulative oil production from 4,845 wells is still growing linearly with the square root of time; and (2) 6,401 wells are already in exponential decline after approximately seven years on production. In addition, 2,363 wells have discontinuous production records, because of refracturing or changes in downhole flowing pressure, and are matched with a linear combination of scaling curves superposed in time. The remaining 1,279 new wells with less than 12 months on production have too few production records to allow for robust matches. These wells are scaled with the slopes of other comparable wells in the square-root-of-time flow regime. In the end, we predict that total ultimate recovery from all existing horizontal wells in Bakken will be some 4.5 billion barrels of oil. We also find that wells completed in the Middle Bakken formation, in general, produce more oil than those completed in the Upper Three Forks formation. The newly completed longer wells with larger hydrofractures have higher initial production rates, but they decline faster and have EURs similar to the cheaper old wells. There is little correlation among EUR, lateral length, and the number and size of hydrofractures. Therefore, technology may not help much in boosting production of new wells completed in the poor immature areas along the edges of the Williston Basin. Operators and policy-makers may use our findings to optimize the possible futures of the Bakken shale and other plays. More importantly, petroleum industry may adopt our physics-based method as an alternative to the overly-optimistic hyperbolic DCA that yields an "illusory picture" of shale oil resources.

The principal aim of this descriptive-survey investigation is to ascertain the factors influencing individuals' choice to purchase organic commodities in Tehran. The statistical populace for this examination comprised all patrons of food retail establishments in Tehran, with the sample size determined using the Cochran formula for an unknown community size, involving the distribution of 30 questionnaires to customers (n=439). Data collection was carried out through a random sampling technique. The survey instrument consisted of a questionnaire with two sections consisting of general queries (7 questions) and specific inquiries (23 items) categorized into four dimensions (product, price, place, and promotion) for the clientele. The questionnaire's validity was confirmed through face and content validation, while its reliability was assessed utilizing Cronbach’s alpha. Data analysis was conducted using SPSS25 software, encompassing both descriptive and inferential statistical analyses. The results revealed a positive and significant correlation between customers' inclination to consume organic goods and the characteristics of the product, price, and promotion. However, no association was found between the propensity to consume organic products and location characteristics. Concerning contextual variables, a solely positive and significant correlation was identified between the willingness to purchase organic items and consumer income levels. No significant relationships were detected between other contextual variables and organic product consumption. A notable contrast was observed between respondents' gender and their readiness to buy organic products, while no significant variances were noted regarding age, income, occupation, and education in relation to the propensity to purchase organic commodities.

In this study, a new type of temperature sensor device was developed. The circular electrode of the thermal sensitive sensor was modified with TMT and O₂ plasma to enhance the conductivity by forming a thin SnOxCy layer on the electrode surface. The Nano-Au particles were subjected to O₂ plasma pretreatment to form peroxide groups on the surface. The thermally sensitive sensor was made by mixing the above-treated Nano-Au particles with N-isopropylacrylamide (NIPAAm) to form solution and then UV-induced grafting polymerization of the NIPAAm-containing solution onto the electrode substrate. The composite hydrogels on the electrode introduce thermo-sensitive polymeric surface films for temperature sensing. Using ambient environment resistance test to measure the resistance, the LCST (lower critical solution temperature) of Nano-Au (MUA) mixed with NIPAAm hydrogel was found to be 32 °C. At ambient temperatures higher than LCST, the electrode resistance decreases linearly.

Spectral characteristics of CDOM in water column are a key parameter for bio-optical modeling. Knowledge of CDOM optical properties and spatial discrepancy based on the relationship between water quality and spectral parameters in Yinma River watershed with in situ data collected highly-polluted waters are exhibited in this study. Seasonal field data sets collected over a period of 2 months in 2015 in Yinma River Watershed. Based on the comprehensive index method, the riverine waters showed serious contamination, especially the COD, Fe, Mn, Hg and DO were out of range contamination warning. Dissolved organic carbon (DOC) and total suspended matter (TSM) with prominent non-homogenizing were significantly high in the riverine waters, but chlorophyll-a (Chl-a) was opposite. Ternary phase diagram showed that non-algal paritcles absorption played an important role in total non-water light absorption (>50%) in most sampling locations, and mean contribution of CDOM were 13% and 22% in summer and autumn respectively. Analysis of ratio of absorption at 250-365 nm (E_250:365) and spectral slope (S_275-295) indicated that CDOM had higher aromaticity and molecular weight in autumn than in summer, is consistent with the results of water quality and relative contribution. Redundancy analysis (RDA) indicated that the environmental variables OSM had a strong correlation with CDOM absorption, followed by heavy metal, e.g., Mn, Hg and Cr⁶⁺. However, for the specific UV absorbance (SUVA₂₅₄), the seasonal values showed opposite results compared with the reported literature. The potential reasons were the more UDOM (uncolored Dissolved Organic Matter) from human source (wastewater effluent) existed in waters. Terrigenous inputs simultaneously are in relation to the a_CDOM(440)-DOC relationship with the correlation coefficient was 0.90 in summer (2-tailed, p<0.01), and 0.58 in autumn (2-tailed, p<0.05). Spatial distribution of CDOM parameters exhibited that the downstream regions focused on dry land have high CDOM molecular weight and aromatic hydrocarbon. Partial sampling locations around the cities or countries generally showed abnormal values due to terrigenous inputs. As a bio-optical model parameter, spectral characteristic of CDOM is helpful in adjusting the derived algorithms in highly-polluted environments. The study on organic carbon and pollutants in highly-polluted waters had an important contribution to global carbon balance estimation and water environment protection.

Aims: The aim was to examine how loneliness was associated with bullying victimization at school and online. Methods: We used data from the Danish arm of the international Health Behaviour in School-aged Children (HBSC) study from 2022. The study population was a nationally representative sample of 11-15-year-olds who completed the internationally standardized HBSC questionnaire at school, n=5382. Multilevel logistic regression was applied to study the associations between bullying victimization and loneliness. Results: The prevalence of reporting loneliness often or very often was 9.0%; 6.3% of the sample experienced habitual bullying victimization at school and 4.8% incurred cyberbullying. There was a strong and graded association between loneliness and bullying victimization at school and cyberbullying. The associations were significant for boys and girls and the association between exposure to bullying at school and loneliness was steeper for boys than girls. The gradients were steeper for physical than cyberbullying. Students exposed to habitual bullying in both contexts had an adjusted OR (95% CI) of 11.21 (6.99-17.98) for loneliness. Conclusion: Exposure to bullying at school and cyberbullying are strongly associated with loneliness. It is important to reduce bullying at school and at the internet, and to promote effective interventions to reduce continuing loneliness.

One of the most concerning global environmental issues is the pollution of agricultural soils by heavy metals (HMs), especially cadmium (Cd), which not only affects human health by taking Cd-containing foods but also impacts the quality of rice. The soil's nitrification and denitrification processes, coupled with the release of volatile organic compounds by plants, raise substantial concerns. The understanding of three aspects of paddy soil under conditions of heavy-metal pollution and water management is currently limited. In this review, we summarized recent literature related to the deleterious effects of Cd on both soil processes related to the N cycle and rice quality, particularly aroma, in different water management practices. Under both continuous flooding (CF) and alternate wetting and drying (AWD) conditions, cadmium (Cd) has been observed to reduce both nitrification and denitrification processes. The adverse effects are more pronounced in continuous flooding (CF) compared to alternate wetting and drying (AWD). Similarly, the alteration in rice aroma is more significant in AWD than in CF. The precise modulation of volatile organic compounds (VOCs) by Cd, remains unclear based on the available literature. Nevertheless, HM accumulation is higher in AWD conditions compared to CF, leading to a detrimental impact on volatile organic compounds (VOCs). The literature concluded that AWD practices should be avoided in Cd contaminated fields to decrease accumulation and maintain the quality of rice. In the future, rhizospheric engineering and plant biotechnology can be used to decrease the transport of HMs from the soil to the plant’s edible parts.

The objective of this work was to investigate the deacidification of bio-oils (BOs) from triglyceride-based biomass through the application of liquid-liquid extraction (LLE) in a simple stage, using methanol and water as a binary solvent and feed/solvent ratio of 1/1. For this, the effects of process parameters such as the water content present in the solvent, the content of carboxylic acids present in the bio-oil, and the extraction temperature on the deacidification process through the efficiency and distribution coefficient were evaluated, as well as the effects of such parameters on the quality of deacidified bio-oils through physical-chemical analyzes and GC-MS analysis. The results show that such process parameters significantly affect the quality of deacidified bio-oils. The ideal condition to have the highest acid removal, i.e., the highest deacidification efficiency (72.65%), is the one in which the deacidification process is performed with aqueous methanol (5% water) at 35 °C and for BOs that have a total acid number (TAN) equal to 24.38 mg KOH/g. Therefore, the process of deacidification by LLE using aqueous methanol is a promising alternative for removing carboxylic acids and other oxygenated compounds, contributing significantly to the upgrading or improving biofuels produced by catalytic thermal cracking.

Soil organic matter (SOM) is important for the global carbon cycle, and hyperspectral remote sensing has proven a promising method for fast SOM content estimation. However, soil physical properties significantly affect the sensitivity of satellite hyperspectral imaging to SOM, leading to poor generalization ability of the estimation model. This study aims to improve the spatiotemporal transferability of the SOM prediction model by alleviating the coupling effect of soil physical properties on the spectra. Based on satellite hyperspectral images and soil physical variables, including soil moisture (SM), soil surface roughness (root mean squared height, RMSH), and soil bulk weight (SBW), a soil spectral correction strategy was established based on the information unmixing method. Two important grain-producing areas in Northeast China were selected as study areas to verify the performance and transferability of the spectral correction model and SOM content prediction model. The results showed that soil spectral corrections based on fourth-order polynomials and the XG-Boost algorithm had excellent accuracy and generalization ability, with residual predictive deviations (RPD) exceeding 1.4 in almost all bands. In addition, when the soil spectral correction strategy was adopted, the accuracy of the SOM prediction model and the generalization ability after model migration were significantly improved. The SOM prediction accuracy based on the XG-Boost corrected spectrum was the highest, with a coefficient of determination (R2) of 0.76, root mean square error (RMSE) of 5.74 g/kg, and RPD of 1.68. The prediction accuracy, R2, RMSE, and RPD of the model after migration were 0.72, 6.71 g/kg, and 1.53, respectively. Compared with the direct migration prediction of the model, adopting the soil spectral correction strategy based on fourth-order polynomials and XG-Boost reduced the RMSE of the SOM prediction results by 57.90% and 60.27%, respectively. The performance comparison highlighted the advantages of considering soil physical properties in regional-scale SOM prediction.

Cerebrospinal fluid contacting neurons (CSF-cNs) are a specific type of neurons located around the ventricles in the brain and the central canal in the spinal cord and have been demonstrated to be intrinsic sensory neurons in the central nervous system (CNS). One of the important channels responsible for the sensory function is polycystic kidney disease 2-like 1 (PKD2L1) channel. Most of the studies concerning the distribution and function of the PKD2L1-expressing CSF-cNs in the spinal cord have previously been performed in non-mammalian vertebrates. In the present study immunohistochemistry was performed to determine the distribution of PKD2L1-immunoreactive (IR) CSF-cNs in the spinal cords of 4 mammalian species: mouse, rat, cat, and macaque monkey. Here, we found that PKD2L1-expressing CSF-cNs were present at all levels of the spinal cord in these animal species. Although the distribution pattern was similar across these species, differences existed. Mice and rats presented a clear PKD2L1-IR cell body labeling, whereas in cats and macaques the PKD2L1-IR cell bodies were more weakly labeled. Ectopic PKD2L1-IR neurons away from the ependymal layer were observed in all the animal species although the abundance and the detailed locations varied. The apical dendritic protrusions towards the lumen of the central canal were clearly seen in all the animal species, but the sizes of protrusion bulbs were different among the species. PKD2L1-IR cell bodies/dendrites were co-expressed with doublecortin, MAP2 (microtubule-associated protein 2) and aromatic L-amino acid decarboxylase, but not with NeuN (neuronal nuclear protein), indicating their immature property and ability to synthesis monoamine transmitters. In addition, in-situ hybridization performed in rats revealed PKD2L1 mRNA expression in the cells around the central canal. Our results indicate that the intrinsic sensory neurons are conserved across non-mammalian and mammalian vertebrates, and that this may play an essential role in the regulation of motor and sensory functions as well as in the maintenance of homeostasis in the CNS.

The market of natural and organic cosmetics has been growing in last decades. The increase in interest in this type of product is a consequence of the concern that consumers have been presenting in relation to the environment and health. In addition to the appreciation the use of sustainable ingredients in cosmetic formulations, the consumers are also concerned about pollution caused by the use of plastics, which leads industries to reinvent themselves and rethink about the composition of packaging. The factor that most drives the purchase of natural and organic cosmetics is the fact that the consumer, in addition to contributing to the preservation of the environment, is also using a sustainable product. The growing demand for natural and organic cosmetics results in a concern of the brands with the organic issue, with the decreased use of animal derived ingredients and with the updating the parameters required for certification of a cosmetic as natural or organic. Due to the few studies available in this area, the importance of clarifying the definitions and concepts of natural and organic cosmetics is evident, in order to contribute with accurate information for the cosmetic sector.

A time-sequential working, spatially multiplexed autostereoscopic 3D display design consisting of a fast switchable RGB-color filter array is presented. The wavelength-selective filter barrier emits the light from a display over a larger active area than common autostereoscopic barrier displays. An optical modelling of wavelength-selective barriers has been used for instance to calculate the light ray distribution properties of that arrangement. To find well working display designs, automated searches by simulation and computational evaluation has been proceeded. Wavelength-selective filter barrier arrangements exhibit characteristics different from common barrier displays with similar barrier pitch and ascent. In particular, these constructions show strong angular luminance dependency under barrier inclination specified by correspondent slant angle. In time-sequential implementation it is important to avoid that quick eye or eyelid movement lead to visible color artifacts. In the millisecond regime tunable liquid crystal Fabry-Pérot color filters for the colors red, green and blue are presented. They consist of a sub-micrometer thick nematic layer sandwiched between dielectric mirrors and ITO-electrodes. These cells shall switch narrow-banding light of red, green or blue. An array for a glasses-free 3D display has to be equipped with several thousand switchable filter elements having different color apertures. The newly introduced design is usable as a multi user display as well as a single user system with user adaptive control.